Galileo Quick Start Guide

QUICK START GUIDE
INTEGRATION TOOLS
Galileo™ Remote Computer Control
To control the Galileo remotely from a computer:
1. Attach the Galileo to the computer’s Ethernet port or to a network router or network
switch.
2. Configure the computer’s network settings.
3. Configure the Galileo’s network settings.
4. Launch and configure the Compass control software.
Attaching the Galileo to Your Computer
The Galileo’s RJ-45 port connects to a standard computer Ethernet port, router, or switcher
with shielded CAT-5e cables. The Ethernet connection allows the unit to be controlled
remotely from a Mac® or Windows® computer running the Compass control software. Bidirectional communication ensures that the current settings, whether changed from the
Galileo front panel or from the Compass software, are always in sync.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
E
!
AC INPUT 100-240V~, 50-60Hz, 375W Max.
1
2
3
4
5
6
7
8
13
14
15
16
ANALOG OR
AES/EBU STEREO
CAUTION
WARNINGS: THIS PRODUCT MUST BE GROUNDED. TO ENSUR E
PROPER OPER ATION, ALLOW AT LEAST 2 INCHES CLEARANCE
FROM SIDE FANS AND ADEQU ATE VENTIL ATION. NO OPER ATOR
SERVICEABLE PARTS INSIDE. REFER SE RVICING TO QUALIFIED
PERSONNEL. TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE
Connect to SIM
3022 or 3088 only
ANALOG
(DISABLED FOR
AES/EBU)
OUTPUT
B
D
F
9
10
11
12
Galileo 616
Network switcher or
wireless router
RJ-45
Connector
Shielded
CAT-5e
cables
:
Esc
Computer
~
F1
!
C ap s Lo ck
Shift
C tr l
F2
@
1
`
T ab
X
A lt
C
^
5
R
D
F5
%
4
E
S
Z
F4
$
3
W
A
F3
#
2
Q
N
F8
8
9
I
J
<
,
F9
P
>
.
Alt
F 11
+
F1 2
Sc r oll
Loc k
Paus e
Inser t
Home
Pp
age
U
Delete
End
Page
Dow n
Pr int
Sc reen
|
=
{
[
\
}
]
Num
Lo ck
Num
Loc k
7
Sc roll
Loc k
Ca ps
Loc k
/
*
8
9
4
5
6
1
2
3
Home
-
PgUp
+
:
;
L
F1 0
_
-
0
O
K
M
)
(
*
U
H
B
F7
F6
7
Y
G
V
&
6
T
F
"
'
?
/
En te r
Sh ift
End
Ctr l
0/
Ins
PgDn
.
Enter
Del
Galileo 616 Connected to Computer
1
GALILEO QUICK START GUIDE
Galileo 408
Network switcher or
wireless router
RJ-45
Connector
Shielded
CAT-5e
cables
:
Esc
Computer
~
F1
!
C ap s Lo ck
Shift
C tr l
F2
@
1
`
T ab
X
A lt
C
^
5
R
D
F5
%
4
E
S
Z
F4
$
3
W
A
F3
#
2
Q
N
F8
8
9
I
J
<
,
F9
P
>
.
Alt
F 11
+
F1 2
Sc r oll
Loc k
Paus e
Inser t
Home
Pp
age
U
Delete
End
Page
Dow n
Pr int
Sc reen
|
=
{
[
\
}
]
Num
Lo ck
Num
Loc k
7
Sc roll
Loc k
Ca ps
Loc k
/
*
8
9
4
5
6
1
2
3
Home
-
PgUp
+
:
;
L
F1 0
_
-
0
O
K
M
)
(
*
U
H
B
F7
F6
7
Y
G
V
&
6
T
F
"
'
?
/
En te r
Sh ift
End
Ctr l
0/
Ins
PgDn
.
Enter
Del
Galileo 408 Connected to Computer
NOTE: When connecting the Galileo to a computer through a router, make sure
the router is appropriately configured.
Configuring the Galileo Network Settings and IP Address
The IP address for the Galileo is set to DHCP (Dynamic Host Control Protocol) by default.
DHCP allows the Galileo, or multiple Galileos, to be easily attached to a computer with minimal setup. In addition, the Galileo can also be set to a static IP address. When using a static
IP address, the computer (as well as the router, if you are using one) must be set to the same
IP address as the Galileo.
NOTE: The network settings and IP address for the Galileo 616 can be configured from its front panel on the System Settings > Network page. To configure
the network settings and IP address for the Galileo 408, you must use the Compass
control software (see “Configuring the Galileo Network Settings and IP Address” on
page 2). The network settings and IP address for the Galileo 616 can also be configured from the Compass control software.
2
GALILEO QUICK START GUIDE
Resetting the Galileo to DHCP from the Front Panel
If the Galileo has been set to a static IP address, you can easily reset it to DHCP from the front
panel.
To reset the Galileo to DHCP from the front panel:
1. Power down the Galileo and wait several seconds.
2. Do one of the following:
■
For the Galileo 616, press the Panel Select switches for channels 4, 7, and 8 while powering up the unit.
■
For the Galileo 408, press the Panel Mute switches for channels 4, 7, and 8 while powering
up the unit.
Using the Compass Control Software
Computer Requirements for the Compass Control Software
■
2 GB RAM
■
2 GHz processor or faster
■
Windows Vista; Windows XP SP3 or later; or Mac OS 10.4.11 or later
Installing and Launching the Compass Control Software
To install and launch the Compass control software:
1. Install the Compass control software:
■
For Windows, run the Setup program from the Compass Installer disc.
■
For Mac, drag the Compass software from the Compass Installer disc and extract it to
your computer’s hard drive.
3
GALILEO QUICK START GUIDE
2. Double-click the Compass program to launch it. The Galileo tab displays a list of connected Galileos. If the Compass program is not configured to automatically detect Galileos
when launched, or if you want to search for Galileos recently connected to your computer,
click Find Galileos.
3. To add a virtual Galileo, do the following:
■
On the Galileos tab, click Add Galileo.
■
In the Add Galileo dialog box, select the Galileo Type (Galileo 616 or Galileo 408) and then
enter a fictional IP Address (for example, 1.2.3.4), Galileo Nickname, and Tab Name.
Click OK. The new Galileo is added appears on the Galileos tab.
■
To display demo meters for the virtual Galileo, on the Galileos tab, in the Meters column
for the new Galileo, click None so it changes to “Demo.”
4
GALILEO QUICK START GUIDE
■
In the Virtual column for the new Galileo, click Use Virtual to make the device a virtual
Galileo. A blue tab is created at the top of the screen for the new Galileo.
■
Click the blue tab for the new virtual Galileo to display its settings. Galileo settings are
organized in groups of sub tabs: Project, Settings, Galileo Map, Input Processing, Output
Processing, Summing Matrix, Input Masters, and Output Masters.
4. Click the Compass tab to display global properties for the Compass software.
5
GALILEO QUICK START GUIDE
Configuring Galileo Network Settings in the Compass Control Software
To configure the network settings and IP address for the Galileo 408, you must use the
Compass control software. The network settings and IP address for the Galileo 616 can be
configured from either its front panel or with the Compass control software.
To configure Galileo network settings in the Compass control software:
1. In the Compass control software, click the tab for the Galileo you want to configure.
2. On the Settings > Network page, click Edit Network Settings.
3. In the Network Settings dialog box, select one of the following options:
■
Select DHCP to use the Dynamic Host Control Protocol.
■
Select Static to use a static IP address. Enter a Static IP Address, Net Mask, and Gateaway.
4. Click OK to close the Network Settings dialog box.
6
GALILEO QUICK START GUIDE
7
GALILEO QUICK START GUIDE
Meyer Sound Laboratories Inc.
2832 San Pablo Ave.
Berkeley, CA 94702
www.meyersound.com
T: +1 510 486.1166
T: +1 510 486.8356
© 2009
Meyer Sound. All rights reserved.
Galileo Quick Start Guide
The contents of this manual are furnished for informational purposes only, are subject to change without
notice, and should not be construed as a commitment by Meyer Sound Laboratories Inc. Meyer Sound
assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual.
Except as permitted by applicable copyright law, no part of this publication may be reproduced, stored in
a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, recording or otherwise, without prior written permission from Meyer Sound.
Galileo, Compass, Composite EQ, TruShaping, M Series, M1D, M2D, M’elodie, and MICA are trademarks
of Meyer Sound. Meyer Sound, SIM, M3D, and MILO and are registered trademarks of Meyer Sound
Laboratories Inc. (Reg. U.S. Pat. & Tm. Off.). All third-party trademarks mentioned herein are the property
of their respective trademark holders.
Printed in the U.S.A.
Part Number: 05.141.002.09 B
8