commando 300 - Sandvik Mining and Construction

commando 300 - Sandvik Mining and Construction

COMMANDO 300
02130-1
2002-01-02
1/4
Technical description
Commando 300 is a hydraulic, self-propelled drilling
unit on a 4-wheel, oscillated drive carrier. It drills holes
with a maximum recommended diameter of 64 mm (2
1/2") and a maximum practical length of 15 metres
(50'), utilizing 25, 28 or 32 mm (1", 1 1/8" or 1 1/4")
extension rods.
Commando 300 is a completely self contained drilling
unit. It is easily manoeuvrable with good rough terrain
capabilities. It is also easy to transport between job
sites on a truck or on a trailer, or it can even be lifted
by a helicopter.
Commando 300 is equipped with HL 300, hydraulic top
hammer rock drill. The rock drill is mounted on an
aluminium chain feed, which is attached to an
2
articulated boom giving a drilling coverage of 10 m
(108 sq-ft). A 48 kW (64 hp) diesel engine supplies
power both for hydraulic pumps and for an on-board
compressor. Several routine functions of Commando
300, e.g. collaring and antijamming, are automatically
executed by electronic controls.
SANDVIK TAMROCK reserves the right to change this specification without further notice.
For easy operation, good visibility and operator safety,
Commando 300 is supplied with an electronic remote
control unit. Thanks to the electronics, this unit has
fewer levers which make it easy to use. For operator
comfort Commando 300 is also equipped with a dust
collection system, which gathers drilling dust from the
hole into a plastic bag.
Typical applications for Commando 300 are foundation
drilling, road cutting, trenching, occasional bolting and
other
special
drilling
applications.
Therefore
Commando 300 is most often used by construction
contractors, mines and quarries, and the municipal
sector. Due to its versatility Commando 300 is often
included in the equipment fleet of rental houses as
well.
SANDVIK TAMROCK OY, P.O.Box 100, FIN-33311 Tampere, FINLAND
Tel.int. +358 205 44 121, Telefax int. +358 205 44 120
COMMANDO 300
Spec. no: 02130-1
2002-01-02
2/4
Drilling geometry
Transport dimensions
5560
5560
3770
2700 (max)
3770
2970
1400 (min)
SANDVIK TAMROCK reserves the right to change this specification without further notice.
SANDVIK TAMROCK OY, P.O.Box 100, FIN-33311 Tampere, FINLAND
Tel.int. +358 205 44 121, Telefax int. +358 205 44 120
2280
260
2580
1200 (max)
0 (min)
COMMANDO 300
Spec. no: 02130-1
2002-12-20
3/4
Hydraulic rock drill
Rock drill type
Drill rod diameters
Shank adapter
Operating pressure
Percussion rate
Percussion output power
Maximum rotation torque
Shank lubrication
Flushing
Weight
Powerpack
HL 300
32 mm (25, 28 mm)
Standard
90-160 bar
50 Hz
8 kW
245 Nm (400 Nm)
/170 bar
Grease
Air or water
94 kg
Chain feed
Chain feed type
Length of feed
Rock drill travel
Max. length of starter rod
Hole length with starter rod
Feed/pull out force
Retaining centralizer
Feed extension travel
Feed swing
Feed tilt
Weight
CF 300 x 12
5 560 mm
4 070 mm
3 660 mm
3 300 mm
15 kN
Pito 9H
1 300 mm
+/- 47°
110°
245 kg
Engine type
Number of cylinders
Engine output
Transmission type
Hydraulic pumps
Screw compressor type
Air flushing capacity
Flushing air pressure
Air cleaner
Fuel tank
Average fuel consumption
Max. operating altitude
Fuel saving system
Deutz BF4L 1011/F,
air/oil cooled
4
48 kW/2800 rpm
Direct/v-belt
One variable
displacement, two
gear pumps
Enduro 12
3
2.5 m /min
4-8 bar
2 pcs
100 l
8-10 l/h
3000 m
Standard
Hydraulic system
Driving, boom and percussion
Rotation and dust collector
Filtration rate
Cooling capacity
Hydraulic oil tank
Load sensing system
Open center
12 micron abs.
up to +40°C ambient
85 l
Control system
Articulated boom
Boom type
Boom length
Boom swing
Vertic. drilling coverage on flat
Vertical collaring height
Horizontal holes
DB 300
4m
+/- 40°
2
10 m
+2.2 m/-4.6 m
Sideways, forwards
Oscillation angles
Ground clearance
Tramming force
Tramming speed
Number of hydraulic jacks
Antijamming system
Voltage
Carrier
Carrier type
Driving and jack control
Boom and drilling control
Collaring control
Percussion control
Rubber tyred,
4-wheel drive
+/- 16°
380 mm
31 kN
4.5 km/h
4
Direct hydraulic
Electric remote
Automatic, adjustable
Controlled by feed
pressure
Both feed and
percussion are
controlled by time
relays
12 VDC
Dust collection system
Dust collector type
Capacity/vacuum
Filter elements/material
Total filter surface
Hydraulic motor output
Weight
DC 410H
3
10 m /min at 950 mm
vacuum H2O
9 pcs/fiber
2
7.2 m
5.5 kW
110 kg
Transport dimensions
Operating weight
Width without tracks
Height
Total length
SANDVIK TAMROCK reserves the right to change this specification without further notice.
4 800 kg
(without options)
2.3 m
2.6 m
5.6 m
SANDVIK TAMROCK OY, P.O.Box 100, FIN-33311 Tampere, FINLAND
Tel.int. +358 205 44 121, Telefax int. +358 205 44 120
COMMANDO 300
Spec. no: 02130-1
2002-01-02
4/4
Standard components
Selection of options
1. Rock drill
2. Chain feed
1.
2.
3.
4.
5.
6.
3. Rod rack
4. Boom
5. Carrier
6. Powerpack
7. Hydraulic system
8. Control system
9. Dust collection system
10. Working lights
11. Hydraulic jacks
12. Swing arm
13. Manuals
HL 300, hydraulic
CF 300 x 12/Pito 9H,
incl. one set of jaws
For 2 extra rods on
chain feed
DB 300, articulated
Rubber-tyred
Diesel driven,
hydraulic pumps and
on-board compressor
Open center and load
sensing
TA 342, electric
DC 410H, hydraulic
4 pcs
4 pcs
For remote control
unit
Operating,
maintenance and
spare parts manuals:
2 x paper copy
2 x CD-ROM
14. EU-safety devices
The jaws for drill steels
1
Drill steel
type
Integral rod for
HE 122 drifter
2
Extension
rods
3
Extension
rods
4
Extension
rods
If several jaws
assembled.
Drill steel
diameter
22 mm
7/8"
25 mm
1"
28 mm
1 1/8"
32 mm
1 1/4"
selected
HE 122 rock drill (replaces standard component)
Hydraulic winch (2 tons)
Pulling device for 22 mm (7/8") rods
Chain tracks
Hydraulic drill steel grinder, Tamrock HGW
Hydraulic drill steel grinder for integral steels,
Sanroc ILH
7. Angle indicator MEC Angie
8. TIM 2104 Tamrock inclination angle measuring and
controlling system
9. Electric filling pump for refuelling
10. Electric engine heater
11. Spirit level angle indicator
12. Hydraulic roll-over (360°) boom head
Specify the boom head dead point
- upwards
- 3 o'clock from front
13. Bigger rotation motor (400 Nm) for 51 or
64 mm holes
14. PTX exhaust gas purifier
15. Water flushing kit without water pump
16. Water flushing kit with water pump
(replaces previous option)
17. Extra manuals
18. First service kit for Commando 300, ID 881 536 39
19. Special tools for HL 300, field kit ID 881 537 69
Recommended
hole diameter
28 - 38 mm
1 7/64 - 1 1/2"
please
38 - 45 mm
1 1/2" - 1 3/4"
38 - 48 mm
1 1/2" - 1 7/8"
45 - 64 mm
1 3/4" - 2 1/2"
specify
jaws
SANDVIK TAMROCK reserves the right to change this specification without further notice.
SANDVIK TAMROCK OY, P.O.Box 100, FIN-33311 Tampere, FINLAND
Tel.int. +358 205 44 121, Telefax int. +358 205 44 120