Model T1517 - National Controls Corp.

Comments

Transcription

Model T1517 - National Controls Corp.
TDR-28
TIME DELAY RELAYS
Fan and Light Control
Model T1517
.781
C
L
Off
TIME
TIME SET
(MINUTES)
On
Min.
Max.
1
2.063
1.640
WIRING DIAGRAM
2.75
4.125
C
L
R
3.281
ON
R
2.375
1.187
National Controls
Corporation
West Chicago, IL. 60185
P/N TNC-T1517-120
Time
15
60
30
45
Delay
1-60 Minutes
TIMING DELAY
ADJUSTMENT
WIRING DIAGRAM
LINE (BLK)
120 VAC
NEUTRAL
5.0
Off
LIGHT
#6-32X7/8 SCREW (2 PL.)
PROVIDED FOR BOX
MOUNTING
.187 X .50
SLOT (2 PL.)
SATIN ALUMINUM
WALL PLATE
On
Fan
1.3
.906
1.562
On
Light
.5" ± .125" STRIP AND TIN TYP.
.50
1.812
LOGIC FUNCTION DIAGRAM
Switch
LENGTH MEASURED
FROM THE COVER: 5.5" ± 1.0",
FAN
MOTOR
Operating Logic: Voltage is applied to the
unit at all times via the black and white
wires. When the switch is placed in the ON
position, power is applied to the lamp and
fan output. When the switch is placed in the
TIMED position, the power is removed from
the lamp output and the fan output stays
on for the preset delay time. After the delay
time the power is removed from the fan output.
Should the switch be placed in the ON
position during the delay time, the timer will
be reset and both outputs will be ON as
defined above.
Should power be interrupted, when in the
TIMED position, the timer will be reset and
when power is re-applied the fan output will
be ON for the preset delay time after the
power is re-applied.
ALL 4 WIRES ARE 18 AWG,
U.L. STYLE 1015, .031 INSULATION
RED
exhaust fan off
Adjustable fan turn off time
Fits single switch outlet box
Simple wire nut hook-up
Cover plate and hardware provided
File #E95644
BLUE
●
●
●
●
●
(WHT)
TIME DELAY
Adjustment: On-board Trimpot
Range: 1 to 60 minutes
Repeatability: ±0.5% +8ms max.
Accuracy:
Maximum time -0%, +10%
Minimum time -30%, +0%
INPUT
Operating Voltage: 120 VAC ±10%
Power Consumption: 3.5 VA max. at 120 VAC
(exclusive of loads)
Frequency: 50/60 Hz
OUTPUT
A-Lamp Load (Switch): 500 W at 120 VAC max.
(blue wire)
B-Fan Load (Switch and Relay Contact):
1/3 hp, 10 A (resistive) at 120 VAC max. (red wire)
Life: 100,000 cycles at full load
MECHANICAL
Mounting: Fits single switch outlet box
Electrical: Simple wire nut hook-up
Switch color: Black
ENVIRONMENTAL
Storage Temperature: -40°C to 70°C
Operating Temperature: -40°C to 55°C
Humidity: 95% relative
LINE (BLK)
SPECIFICATIONS
● One switch controls fan and light
● Digital timing circuit
● Saves energy by automatically turning
120 VAC NEUTRAL
FEATURES
BLUE
RED
LAMP
(WHT)
FAN
MOTOR
5801
1.7
ORDERING INFORMATION
WALL PLATE
INPUT VOLTAGE
ADJ. OFF DELAY
SWITCH COLOR
PART NUMBER
120 VAC
1 to 60 min.
BLACK
TNC-T1517-120
120 VAC
1 to 60 min.
WHITE
TNC-T1517-120W
(ATTACH AFTER INSTALLATION OF UNIT)
Note: The following hardware is supplied with this
product: 2 screws for unit / wall mounting; satin
aluminum wall plate with 2 screws; 4 wire connectors
(screws and wire connectors packed in plastic bag)
Consult factory for any special requirements not listed in catalog (minimum order requirement may apply).
AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: 800-323-2593 • 630-231-5900 • FAX: 630-231-1377 • www.nationalcontrols.com
© 2013 by AMETEK, Inc. All rights reserved.
313PDF (240032)
TDR-29
TIMER ACCESSORIES
Potentiometer
3/8"
3/8" x 32 THREADS
NCC remote mounting potentiometers have 24"
wire leads, dust protection, 1/4" shaft (no knob)
and are calibrated to provide constant timing.
These are suitable for mounting through a panel
and can be used with a dial and knob.
A locking bushing is used in place of knob to
secure setting. Not for use on K or CKK Series
timers.
22 GA. .032 - 105˚ C UL STYLE 1015 WIRE
24" ± 1"
3/8" x 32 NUT
INSULATING TUBING OVER TERMINALS
ORDERING INFORMATION
1 Megohm remote potentiometer
ASY-0001M-450
Locking bushing
MLO-K1701-011
1/4" x .032 FEMALE FASTONS
5.75
Hold-down Straps
.33
.45
A locking bushing is used in place of knob to
secure setting. Used on all plug in timers with
knobs except K and CKK Series.
.500
.437
.065 ± .015
.57
.50
ORDERING INFORMATION
7.00
Hold-down strap for K Series timers
.25
.33
.50 typ.
ASY-STRAP-5.75L
.45
Hold-down strap for T, S, A, and CKK
timers
ASY-STRAP-7.00L
Locking bushing
MLO-010MM-.75
.065 ± .015
1.85
1.76
Mounting Bracket
ORDERING INFORMATION
Mounting bracket for 1/16 DIN
enclosure
MBK-1/16D-011
.16
.28
1.76
.90
2.26
AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: 800-323-2593 • 630-231-5900 • FAX: 630-231-1377 • www.nationalcontrols.com
© 2013 by AMETEK, Inc. All rights reserved.
313PDF (240032)
TDR-30
TIMER ACCESSORIES
Sockets
1.575
.866
.315
.709
MSO-0008P-012
2.362
8-pin circular socket, DIN rail
mountable
165 dia.
5
4
3
7
8
1
2
Mounting Holes
.165 dia. 2 pl.
.984
ORDERING INFORMATION
6
1.299
1.299
2.323
.315
Terminal
Arrangement
ORDERING INFORMATION
7
9
10
6
5
4
2
3
Mounting Holes
.165 dia. 2 pl.
1.063
MSO-0011P-012
.165 dia.
2.632
11-pin circular socket, DIN rail
mountable
8
1.299
11
1.299
1
Top View
.709
.866
1.312
4
1.844
11-pin circular socket for DIN panel
mount
8
7
.156
ORDERING INFORMATION
6
5
MSO-0011P-013
3
2 1
11
10 9
1.844
0.315
6
5
4
3
2
1
0.165 DIA
Mounting Holes (2)
2.205
0.165
MSO-00KUP-012
2.992
ORDERING INFORMATION
11-pin spade socket, DIN rail
mountable
Terminal
Arrangement
0.709
1.457
B
9
1.417
1.693
0.571
A
8
7
Top View
0.987
AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: 800-323-2593 • 630-231-5900 • FAX: 630-231-1377 • www.nationalcontrols.com
© 2013 by AMETEK, Inc. All rights reserved.
313PDF (240032)

Similar documents

www.ametek.com

www.ametek.com gravitometers, liquid densitometers, and trace oxygen analyzers for natural gas, sulfur recovery, chemical production, oil refining, industrial gases, semiconductor manufacture, pharmaceutical man...

More information