especificaciones tecnicas

Comments

Transcription

especificaciones tecnicas
Catalogo de
Productos
2016
EXTINTOR PORTATIL 1 KILO PQS
ESPECIFICACIONES TECNICAS:
• Extintor portátil capacidad 1 kilo presión interna.
• Polvo Químico Seco multipropósito al 40% (Fosfato Monoamonico).
• Certificado Cesmec.
• Para el combate de fuegos clase ABC.
• Rating apague de 1 – A: 2 – B: C.
EXTINTOR PORTATIL 2 KILO PQS
ESPECIFICACIONES TECNICAS:
• Extintor portátil capacidad 2 kilos presión interna.
• Polvo Químico Seco multipropósito al 40%.
• Certificado Cesmec.
• Para el combate de fuegos clase ABC.
• Rating de apague de 2 – A: 5 – B C.
• Incluye soporte.
EXTINTOR PORTATIL 4 KILO PQS
ESPECIFICACIONES TECNICAS:
• Extintor portátil capacidad 4 kilos
presión interna.
• Polvo Químico Seco multipropósito al 40%.
• Certificado Cesmec.
• Para el combate de fuegos clase ABC.
• Rating de apague de 6 – A: 30 – B C.
• Incluye soporte.
EXTINTOR PORTATIL 6 KILO PQS
ESPECIFICACIONES TECNICAS:
• Extintor portátil capacidad 6 kilos presión interna.
• Polvo Químico Seco multipropósito al 40%.
• Certificado Cesmec.
• Para el combate de fuegos clase ABC.
• Rating de apague de 10 – A: 40 – B C.
• Incluye soporte.
EXTINTOR PORTATIL 10 KILO PQS
ESPECIFICACIONES TECNICAS:
• Extintor portátil capacidad 10 kilos presión interna.
• Polvo Químico Seco multipropósito al 40%.
• Certificado Cesmec.
• Para el combate de fuegos clase ABC.
• Rating de apague de 10 – A: 40 – B C.
• Incluye soporte.
repuestos de extintores PQS y CO2
Mangueras PQS de 4 a10 kg :
Mangueras CO2 de 5 kg:
Toberas Co2 de 2 kg:
Abrazaderas:
manometros:
valvulas:
EXTINTOR PORTATIL 2 KILOS DIOXIDO DE CARBONO ( CO2 )
ESPECIFICACIONES TECNICAS:
• Extintor portátil capacidad 2 kilos
• Procedencia RPC
• Dióxido de Carbono (CO²)
• Certificado Cesmec
• Para el combate de fuegos clase BC
• Rating de apague 2 – B : C
• Incluye soporte
EXTINTOR PORTATIL 5 KILOS DIOXIDO DE CARBONO ( CO2 )
ESPECIFICACIONES TECNICAS:
• Extintor portátil capacidad 5 kilos.
• Procedencia RPC.
• Dióxido de Carbono (CO²).
• Certificado Cesmec.
• Para el combate de fuegos clase BC.
• Rating de apague 2 – B : C.
• Incluye soporte.
EXTINTOR PORTATIL ACETATO DE POTASIO 6 LITROS
Los extintores de químicos húmedos son los mejores extintores portátiles para
cocinas de restaurantes y aprobados por la nueva Clase K enlistada por la UL
específicamente para accidentes de cocinas en restaurantes. Contiene una base
especial de acetato de potasio, un agente de bajo PH desarrollado para el uso en
sistemas de pre-ingeniería de cocinas para restaurantes. La existencia actual de
aparatos de cocina más complejos y el uso de aceites no saturados, dictan el uso
de extintores portátiles con mayor capacidad para combatir el fuego y el efecto
de enfriamiento para combatir estos difíciles y calientes incendios.
EXTINTOR PORTATIL ACETATO DE POTASIO 10 LITROS
Los extintores de químicos húmedos son los mejores extintores portátiles
para cocinas de restaurantes y aprobados por la nueva Clase K enlistada
por la UL específicamente para accidentes de cocinas en restaurantes.
Contiene una base especial de acetato de potasio, un agente de bajo PH
desarrollado para el uso en sistemas de pre-ingeniería de cocinas para
restaurantes. La existencia actual de aparatos de cocina más complejos y
el uso de aceites no saturados, dictan el uso de extintores portátiles con
mayor capacidad para combatir el fuego y el efecto de enfriamiento para
combatir estos difíciles y calientes incendios.
EXTINTOR PORTATIL ACETATO DE POTASIO 6 LITROS
ESPECIFICACIONES TECNICAS:
Naturaleza del Agente : Espuma mecánica
Nombre químico: AFFF / AR
Contenido porcentual nominal del compuesto activo: 3%
Potencial de extinción: 2-A :10 -B
Contenido nominal : 6 lts
Masa aprox. cargado: 9,2 kg
Masa aprox. Descargado: 3,2 kg
EXTINTOR PORTATIL ACETATO DE POTASIO 10 LITROS
ESPECIFICACIONES TECNICAS:
Naturaleza del Agente : Espuma mecánica
Nombre químico: AFFF / AR
Contenido porcentual nominal del compuesto activo: 3%
Potencial de extinción: 4-A : 20 -B
Contenido nominal : 10 lts
Masa aprox. cargado: 14,2 kg
Masa aprox. Descargado: 4,2 kg
EXTINTOR PORTATIL ACETATO DE POTASIO 6 LITROS
RED LINE cartridge-operated fire extinguishers are the premium
firefighting units preferred by safety directors worldwide in high
fire-risk industries such as chemical, petro-chemical, oil and gas,
mining, aviation, and power generation. Cartridge-operated
means increased reliability, on-the-spot recharge, ease of service, and superior firefighting performance.
Typical applications include fuel loading racks, heavy construction sites, dip tanks, oil pumping stations, mining equipment,
paint lockers, trucks and buses, fuel storage rooms, production
lines and others. Tough, carbon steel shells resist impact, vibration and corrosion; quality components stand up to years of
service; and special polyester powder paints provide superior
protection against cracking and chipping.
Carro Rodante PQS 25 Kg
ESPECIFICACIONES TECNICAS:
Naturaleza del Agente : Polvo Químico Seco
Multipropósito
Nombre químico: Fosfato mono amónico
Contenido porcentual nominal del compuesto
activo: 90%
Potencial de extinción: 40-A : 60 - B :C
Contenido nominal : 25 kg
Carro Rodante PQS 25 Kg
ESPECIFICACIONES TECNICAS:
Naturaleza del Agente : Polvo Químico Seco Multipropósito
Nombre químico: Fosfato mono amónico
Contenido porcentual nominal del compuesto activo: 90%
Potencial de extinción: 40-A : 60 - B :C
Contenido nominal : 25 kg
Masa aprox. cargado: 55,7 kg
Masa aprox. Descargado: 30,7 kg
Carro Rodante PQS 50 Kg
ESPECIFICACIONES TECNICAS:
Naturaleza del Agente :
Polvo Químico Seco Multipropósito
Nombre químico: Fosfato mono amónico
Contenido porcentual nominal del compuesto
activo: 90%
Potencial de extinción: 40-A : 80-B:C
Contenido nominal : 50 kg
Masa aprox. cargado: 86,6 kg
Carro Rodante PQS 100 Kg
ESPECIFICACIONES TECNICAS:
Naturaleza del Agente : Polvo Químico Seco Multipropósito
Nombre químico: Fosfato mono amónico
Contenido porcentual nominal del compuesto activo: 90%
Potencial de extinción: 40 A : 160 B:C
Contenido nominal : 100 kg
Masa aprox. cargado: 147,5 kg
Masa aprox. Descargado: 47,5 kg
Carro Rodante CO2 10 Kg
ESPECIFICACIONES TECNICAS:
Naturaleza del Agente : Dióxido de Carbono
Nombre químico: CO2
Contenido porcentual nominal del compuesto activo: 100%
Potencial de extinción: 10-B :C
Contenido nominal : 10 kg
Masa aprox. cargado: 37,5 kg
Masa aprox. Descargado: 27,5 kg
Carro Rodante CO2 25 Kg
ESPECIFICACIONES TECNICAS:
Naturaleza del Agente : Dióxido de Carbono
Nombre químico: CO2
Contenido porcentual nominal del compuesto activo: 100%
Potencial de extinción: 20-B :C
Contenido nominal : 25 kg
Masa aprox. cargado: 93 kg
Masa aprox. Descargado: 68 kg
Carro Rodante Espuma 25 Lts
ESPECIFICACIONES TECNICAS:
Naturaleza del Agente : Espuma Mecánica
Nombre químico: AFFF / AR
Contenido porcentual nominal del compuesto activo: 3%
Potencial de extinción: 10-A : 40-B
Contenido nominal : 25 lts
Masa aprox. cargado: 55,4 kg
Masa aprox. Descargado: 30,4 kg
Carro Rodante Espuma 50 Lts
ESPECIFICACIONES TECNICAS:
Naturaleza del Agente : Espuma Mecánica
Nombre químico: AFFF / AR
Contenido porcentual nominal del
compuesto activo: 3%
Potencial de extinción: 20-A : 60-B
Contenido nominal : 50 lts
Masa aprox. cargado: 86,3 kg
Masa aprox. Descargado: 36,3 kg
GABINETE DE RED HUMEDA
70X70X30 con carrete de manguera semirígida de 1”
de 25 metros con piton incluido de 3 posiciones :
neto $130.000 / iva $24.700 / total $154.700
GABINETE DE RED HUMEDA
70X70X30 con carrete de manguera semirígida de 1”
de 30 metros con piton incluido de 3 posiciones :
neto $142.000 / iva $26.980 / total $168.980
GABINETE DE EXTINTOR PQS
Metálico abatible con puerta de vidrio :
Gabinete fabricado con los más altos estándares de seguridad y Calidad, este
gabinete reforzado esta diseñado para dar cuidado a su extintor, resistiendo la
inclemencia del tiempo y la exposición prolongada. Su diseño lo hace visible y
seguro.
Puerta abatible bisagra pomel con mirilla de inspección y terminación de esmalte termo convertible de color rojo normalizado.
GABINETE DE EXTINTOR PQS
Metálico abatible con LLAVE :
Gabinete fabricado con los más altos estándares de seguridad y Calidad, este
gabinete reforzado esta diseñado para dar cuidado a su extintor, resistiendo la
inclemencia del tiempo y la exposición prolongada. Su diseño lo hace visible y
seguro.
Puerta abatible bisagra pomel con mirilla de inspección y terminación de esmalte termo convertible de color rojo normalizado. Cierre con llave única.
GABINETE DE EXTINTOR PQS
Metálico DE QUIEBRE :
Gabinete fabricado con los más altos estándares de seguridad y Calidad, este
gabinete reforzado esta diseñado para dar cuidado a su extintor, resistiendo la
inclemencia del tiempo y la exposición prolongada. Su diseño lo hace visible y
seguro.
Gabinete fijo de quiebre, incluye martillo de quiebre, soporte y cadena para su
fácil manipulación. Todo el gabinete tiene una terminación de esmalte termo
convertible de color rojo normalizado.
GABINETE DE EXTINTOR PQS
Gabinete de policarbonato (CHICO)
GABINETE DE EXTINTOR CO2
Gabinete de policarbonato (GRANDE)
SOPORTE MURAL TIPO L
SOPORTE SIMPLE PARA EXTINTORES DE PQS Y CO2:
SOPORTE MURAL pqs 1KG
mETÁLICO /PLÁSTICO /pLÁSTICO 2 KG
Soporte Metálico para extintor PQS
TIPO ABRAZADERA DE 4 A 10 KG
Soporte reforzado Económico
para extINTORES Pqs de 4 a 6 kg
Soporte reforzado ROJO TRADICIONAL
para extINTORES Pqs de 6 a 10 kg
Uniones, tuercas. Tapas y traspasos STORZ
VALOR RELATIVO SEGUN LA MEDIDA (CONSULTAR EL REQUERIDO)
UNION Y BIFURCACION DE 3”
PARA RED SECA:
PITON NEBLINERO
PARA RED HUMEDa
PITON DE ALUMINIO
TRES POSICIONES
CUBRE VOLANTE
negro con insertos efecto fibra de carbono
FUNDAS CUBRE ASIENTOS
polyester - set para 5 plazas
incluye 4 apoya cabezas
SISTEMA LUZ DIA
conexión positiva (gris) y conexión negativa (morada)
SISTEMA LUZ DIA
Alarma de retroceso 97dB- 12V / 24V / 36V
BOTIQUIN LONCHERO
INCLUYE suministros básicos ante una emergencia
CHALECO REFLECTANTE
CUMPLE CON TODA LA NORMATIVA
CINTAS REFLECTANTES
COLORES VARIOS
KIT ANTIDERRAMES MARCA 3M
PARA FAENAS MINERAS:
neto $66.000 / iva $12.540 / total $ 78.540
CUÑAS DE poliuretano ( PU )
cuñas para camionetas:
neto $36.000 / iva $6.841 / total $ 42.840
cuñas de 20 ton:
neto $42.000 / iva $7.980 / total $ 49.980
cuñas de 60 ton:
neto $69.000 / iva $13.110 / total $ 82.110
PORTA CUÑAS METALICAS
C/U:
neto $11.500 / iva $2.185 / total $ 13.685
PALA ARMABLE
articulada - abierta 24''- cerrada 9,5'':
neto $9.000 / iva $1.710 / total $ 10.710
FOCOS FAENEROS
BALIZAS PARA VEHICULOS MINEROS
BALIZA SYFCO AZUL Y AMBAR
EQUIPO MINERO, OPERACION INVIERNO
SACO YUTE / frasada de polar
CADENAS PARA NIEVE
STANDART
PÉRTIGAS Y ACCESORIOS
Pértiga Completa de 8 Pies con Led
Pértiga Completa de 10 Pies con Led
Pértiga Completa de 12 Pies con Led
Banderín Pértiga / Ampolleta Led Pértiga
/ Resorte Pértiga
TENSORES PARA CADENAS
Cono Minsafe base negra
18” / 28” / 36”
18”
28”
Estrobos con grilletes
5/8 * 4 metros
TRABATUERCAS
VALOR RELATIVO SEGUN LA MEDIDA
(CONSULTAR EL REQUERIDO):
36”
Carrete ataque rápido Con Manguerin
Carrete de manguera semirigida marca AyR Prieto en 1'' por 25
metros con pitón metálico de tres posiciones. Con brazo
abatible en 180 grados. Conexión a red de agua por medio de
manguerín. Pintura electro convertible en dos capas de color
rojo. Equipo certificado por IDIEM de la Universidad de Chile
de acuerdo a requerimientos de normativa del RIDDA.
Incluye:
Manguera Semirígida de 1" x largos 25 MT ., fabricada en
caucho sintético 100 % impermeablePresión de trabajo 225 lbs
Presión de ruptura 710 lbs.
Pitón con patrón de descarga variable, posición de corte
Carrete ataque rápido Kolling
- Carrete interior importado marca Kolling, procedencia
Malasia, similar modelo Angus MK-II, fabricado en lámina
metálica de 1.2 mm. de espesor, compuesto de dos tapas
laterales de 550 mm. de diámetro estampadas y rodonadas,
sistema de grifería interna que permite el paso del agua en
forma constante a través del eje sin necesidad de desenrollar la
manguera.
Pintura termo convertible epóxico, 90 micras en doble capa
Color Rojo Standard
Certificación Internacional
Certificación Chilena por IDIEM
Cumple con norma RIDAA
Incluye:
Manguera Semirígida de 1" x largos 25 MT ., fabricada en caucho
sintético 100 % impermeable
Presión de trabajo 225 lbs
Presión de ruptura 710 lbs.
Pitón con patrón de descarga variable, posición de corte
Foam Proportioning & Loose Equipment
Product
Williams’ “High Head” Through-the-Pump
1500 Portable Foam System
Description:
The Williams High Head Through-the-Pump 1500 Portable Foam
System was designed to turn any pumper into a foam producing device. This
unit will proportion 3% foam solution up to 1500 GPM. It can work against
hydrant pressure up to 50 PSI with only 150 PSI discharge pressure. This
economical system is easy to use and is completely water driven; there are no
pumps or parts to maintain. Can’t get the foam to the pump? Not a problem!
The WTTP was designed to proportion foam from remote locations.
FEATURES:
• Operates against 33% Pump Suction Pressure.
(Example: Master Pressure @150 PSI, Suction Pressure @ 50 PSI)
• Proportions Class “B” Foam up to 1500 GPM at 3%.
• Proportions Class “B” Foam up to 750 GPM at 6%.
• Positive Shut-Off on Metering Valve.
• Requires no maintenance.
• Portable.
• Water Powered.
• Remote Proportioning Capabilities.
• Check Valve Prevents Water from “Back Flowing“
into Concentrate Source.
System Includes:
• Base Unit with Jet Pump & Metering Valve.
• 2.0” Clear Concentrate Pick-Up Hose.
• 2.0” Valved Drum Stinger.
ThunderStorm
AFFF/ATC
MATERIALS OF CONSTRUCTION:
• Brass with Stainless Steel Trim.
Notes:
1. The following table is based on 150 psig operating pressure at the jet pump inlet.
2. At 50 psi water pump inlet, maximum hose lay is 25 ft. of 3.0” hose.
3. For drafting operations or pressure below 10 psi, use the 10 psi numbers shown.
Maximum Hose Lay (ft) For Remote Proportioning Portable WATP 1500 System
PUMP INLET PRESSURE
Solution Rate
1%
3%
30
10 PSI
HOSE SIZE
6%
20 PSI
HOSE SIZE
30 PSI
HOSE SIZE
40 PSI
HOSE SIZE
2.5”
3”
2.5”
3”
2.5”
3”
2.5”
3”
12
850
1700
625
1250
400
775
200
325
100
40
825
1675
600
1225
375
750
175
300
400
160
80
800
1625
575
1175
350
725
150
275
1000
400
200
750
1500
525
1050
325
650
125
250
2000
750
375
650
1325
475
950
300
600
100
225
4000
1500
750
525
1050
375
775
250
475
75
200
Foam Proportioning & Loose Equipment
Product:
Williams’ Pressure Reducing Valve
(WPRV/3, 3P, 4 & 4P)
Description:
Maintains constant pre-set inlet pressure for use in conjunction with the Williams “High Head” Through/Around The Pump
(or comparable) foam systems. Allows any firewater pump to produce suction side foam at virtually ANY positive inlet pressure.
As such, the WPRV eliminates need for operator intervention to
adjust intake gate valves due to suction pressure fluctuations as a
result of changes in pump discharge flow. Thus, the added burden
of assuring a maximum pump intake pressure (based on pump
discharge pressure) associated with traditional suction side foam
systems simply goes away.
Additional Applications:
Got a CAFS or Balanced Pressure system? The WPRV can provide reduced pump inlet pressures to allow increased
engine/PTO speed to maintain higher compressor or foam pump output when operating with positive pump inlet pressures.
Installed within a discharge line, the WPRV maintains a preset pressure for hand lines or ground monitors independent of
higher pump discharge pressures.
Features:
3 Modes of Operation:
1. AUTOMATIC – Controls pre-set pressure from 15-115 PSI
2. OPEN – Full flow to rated capacity
WPRV/3 — 500 GPM w/ 7 PSI drop
WPRV/4 — 1500 GPM w/ 20 PSI drop
3. CLOSED — Bubble tight shut off
• NFPA 1901, 14-6 COMPLIANT — Exclusive WPRV pilot control also provides bubble tight shut off to comply with
NFPA 1901, 19-3.6, TIA 99-1 preventing foam solution back flow into a potable (hydrant system) water supply
• PRESSURE RATINGS — 230 PSI Max. — 20 PSI Min. (Prevents reducing hydrant system pressures below 20 PSI)
• INLET/OUTLET — WPRV/3: 2.5” NST; WPRV/4: 5” Storz
Options:
WPRV/3 & 3P (Portable)
• “In-Truck” installation with panel mount control valve, standard 2.5” (F)NST swivel inlet w/ strainer and bleeder port
• 3” (F) NST inlet w/strainer/outlet
• 4” Storz inlet w/strainer/outlet WPRV/4 & 4P (Portable)
• “In-Truck” installation with panel mount control valve, standard 5” Storz inlet w/strainer, adjustable intake relief,
bleeder port and mounting hardware
• Inlet intake relief valve & bleeder (4P)
• 4” Storz inlet w/strainer/outlet
• 6” (F)NST swivel outlet for direct mounting to pump intakes
• Inlet/outlet pressure gauges
• Carrying handle
• 5” LDH X 10’ Long with 5” Storz couplings (200 PSI operating pressure)
Materials of Construction:
• WPRV/3 & 3P – Epoxy coated cast iron w/brass and stainless steel trim
• WPRV/4 & 4P – Epoxy coated & anodized aluminum w/brass and stainless steel trim
Foam Proportioning & Loose Equipment
Product
Tank Farm Fire Fighting Foam System
“Old Style” 2 x 6 Gun JRCP Hose Lay Comparison
Flow
Rate
Solution
%
Jet
Size
# of Jet
lays
2.0” Hose
Lay (ft) Time (min)
6,000
1
2
1
N/A
6,000
1
1.5
2
6,000
3
2
3
2.50” Hose
Lay (ft) Time (min)
3.0” Hose
Lay (ft) Time (min)
N/A
350
1.0
750
2.8
440
1.4
1,300
6.1
2,550
17.4
N/A
N/A
75
0.3
150
0.6
Ambassador JRCP Hose Lay Comparison
Flow
Rate
Solution
%
Jet
Size
# of Jet
lays
2.0” Hose
Lay (ft) Time (min)
2.50” Hose
Lay (ft) Time (min)
3.0” Hose
Lay (ft) Time (min)
6,000
1
2
1
N/A
N/A
350
1.0
750
2.7
6,000
1
1.5
2
434
1.3
1,250
6.0
2,550
17.2
6,000
3
2
3
N/A
N/A
150
0.5
300
1.2
Foam Proportioning & Loose Equipment
Product:
Jet Ratio Controllers (Jet Pumps)
Description:
Utilizing a small amount of water, this high efficiency venturi-type device moves foam concentrate from a remote storage
location to a matched Hydro-Foam™ nozzle. This all-hydraulic
system dramatically simplifies and improves the logistics of
moving the high quantities of foam concentrate required to
extinguish a large flammable liquid fire. Foam concentrate is
delivered from the Jet Ratio Controller to a matched HydroFoam™ nozzle via fire hose. Depending on nozzle and hose
size, as well as the percentage of foam mixed (1% or 3%), the
distance between the foam supply and Hydro-Foam™ nozzle
can be up to 2,500 feet.
Jet Ratio Controllers are supplied in conjunction with matched Hydro-Foam™ nozzles. Foam concentrate inlet on
matched nozzle can be provided with 8 ft. of reinforced clear plastic hose with PVC shut-off valve, and/or metering valve
“stinger”. This configuration allows foam concentrate to be drawn directly from a foam concentrate drum and then delivered
efficiently to the nozzle via fire hose.
Jet Ratio Controllers are provided with connections at three ports, designated as “inlet,” “discharge” and “suction.” Inlet
(female swivel) and discharge (rigid male) has National Hose thread (NST, NH) connections with NPT (M) connection for
the concentrate inlet port. Foam concentrate inlet is furnished with standard drum kit, which consists of flexible suction hose,
rigid PVC “Stinger” pipe and shutoff valve. Jet Ratio Controller body is all brass construction. “H” series jet ratio controllers
are available, on special order, for elevated nozzles, or other high back pressure applications.
Typical Schematic
ThunderStorm®
AFFF/ATC
Foam Proportioning & Loose Equipment
1.5”
INLET
TYPICAL SCHEMATIC
ThunderStorm®
AFFF/ATC
MODEL
3%
Flow Match 1%
DISCHARGE “A”
SUCTION “B”
LENGTH “C”
1.5JP24
750 GPM
2000 gpm
1.5”
1.5”
12.375”
1.5JP30
1000 GPM
2500 gpm
1.5”
1.5”
12.375”
2.0JP60
2000 GPM
5000 gpm
2.5”
2”
15.5”
NOTE: 6% APPLICATIONS AVAILABLE UPON REQUEST
Foam Proportioning & Loose Equipment
Product:
95 gpm Liquid Eductor
Description:
The Elkhart 242-95 Eductor is a device used for educting a liquid concentrate solution into the water stream of
1-1/2” coupled fire hose lines.
The Eductor is constructed of Armor-Lyte ™ composite
material with stainless steel components for resilience and
durability. Armor-Lyte ™ is impervious to the corrosion
caused by high concentrate detergents, salt water and most
chemicals.
Each eductor comes equipped with a 1-1/2” “F” NH
female swivel connector input, a 1-1/2” “M” NH male outlet
and a 3/4” male Garden Hose Thread inlet for the concentrate pick-up hose.
The 242-95 Eductor is factory calibrated for pump flow rates of 95gpm (356 lt/m). The Eductor comes complete with
three different checkvalves for three different concentrate eduction rates. When attached, the Black checkvalve will educt at
a 0.5% rate, the Purple checkvalve will educt at a 1% rate and the Green checkvalve is for educting at a 3% rate.
T o swi tch check val ves on the eductor uni t, gentl y grasp the check val ve body wi th pl i ers or vi se gri ps and unscrew.
Carefully screw alternate checkvalve into eductor body, thread to “hand-tight”. There is no need to over tighten.
The 242-95 Eductor can be used as either an “End-of-the-Line” or as a “Pump Mounted” System. The eductor is designed
for a nominal operating pressure of between 75 and 150 psi. If proportioning 3%, the 242-95s are restricted to a maximum
1.50”ID fire hose goes to 200 feet when used with a 95+gpm nozzle.
The Eductor comes complete with
three different checkvalves for three
different concentrate eduction rates.
*Armor-Lyte™ is a registered trademark of
Williams Fire and Hazard Control, Inc®
Foam Proportioning & Loose Equipment
Product:
Spectrum Inline Eductors
Description:
Spectrum Inline Foam Eductors provide the simplest and
most economical method of introducing a controlled flow of
foam concentrate into a pressurized water stream. As opposed to
“Hydro-Foam™ Technology”, (which is used in conjunction with
master stream nozzles) these “Venturi-Type” foam proportioners
are designed to be used in conjunction with a matched constant
flow end-of-line device (nozzle), where adequate water pressure
is available. Inline foam eductors are capable of operating at inlet
pressures as low as 70 psi, but in most cases adequate residual fire
fighting pressure at the nozzle requires that the eductor inlet pressure be at least 100 psi, or greater.
Spectrum Inline Eductors are rated to flow 60, 95, or 125 gpm @ 150 psi inlet. Nominal flow rates at other inlet pressures are listed below. Eductor outlet pressure is approximately 65% of inlet pressure. Eductor components, including body,
venturi jet and metering orifice are constructed of corrosion-resistant brass.
Standard water inlet - NH (F) swivel. Foam solution discharge - NH (M). Complete with clear pvc concentrate pick-up
hose with slotted brass “stinger”; 1% or 3% fixed orifice; ball check valve.
RIGID
Model
Nominal Flow
@100 PSI
Nominal Flow
@125 PSI
Nominal
@150 PSI
Proportioning
1.5” -60 gpm
49 gpm
55 gpm
60 gpm
1% or 3%
1.5” -95 gpm
78 gpm
87 gpm
95 gpm
1% or 3%
1.5” -125 gpm
102 gpm
114 gpm
125 gpm
1% or 3%
Foam Proportioning & Loose Equipment
Product:
Spectrum “Double Action” By-Pass Eductor
Description:
The Spectrum “Double Action” By-Pass Foam Eductor provides the versatility of a full-flow water by-pass foam proportioner
in conjunction with the simplicity and reduced weight of a standard, single waterway inline eductor. This specialty by-pass type
foam venturi transforms any 1.5” handline into a foam proportioning system. Three flow rates are available: 60 gpm; 95 gpm; 125
gpm. Flows are based on 200 psi inlet pressure. The eductor will
proportion foam at lower inlet pressures, provided that discharge
pressure is not excessive. Positive shut-off metering allows foam
proportioning to be adjusted and set from 0.5% to 3%. Body is
constructed of durable 6061 - T6 (black) anodized aluminum.
In operation, foam is produced by simply installing the system in the hose line, emersing the concentrate pickup tube
into an adequate supply of ThunderStorm® AFFF foam concentrate and adjusting the eductor to the “foam” position. When
foam application is no longer needed, there is no need to remove the eductor for application of water only. This conversion
is easily accomplished by simply rotating the foam control sleeve to the “water” setting. The result is an enlarged waterway
which allows for water only application.
Other Features Include:
• Positive Shutoff Metering Valve.
• Integral Concentrate Ball Check Valve.
• Clear Plastic Concentrate Pick Up Hose with Rigid “Stinger”.
• Lightweight, Compact Design (4 lbs., nominal).
Double Action
Eductor
Nominal Flow
@200 PSi
K-Factor
Inlet
Discharge
Proportioning
Range
60 gpm
60 gpm
4.25
1.5 NH (F) Swivel
1.5” NH (M)
0.5%-6%
95 gpm
95 gpm
6.72
1.5 NH (F) Swivel
1.5” NH (M)
0.5%-6%
125 gpm
125 gpm
8.84
1.5 NH (F) Swivel
1.5” NH (M)
0.5%-6%
“PKW™” Dry Chemical Delivery Manifold —
Typical Layouts
Hydro-Chem™ Technology
Manifolds for Hydro-Chem™ Systems
Dry Chemical Manifiold - 4 Inlets
Dry Chemical Manifiold - 6 Inlets
Hydro-Chem™ Technology
Typical Hose Lay For Hydro-Chem™ Trailer mount Systems
1000 GPM Hose Layout
Patriot II Hose Layout
Monitors
Product:
Daspit Tool™
Features:
Patented “Daspit Tool” tank frame clamp with 5” vertical waterway
“Daspit Tool” Specialty Flange Monitor Adapter
“Daspit Tool” Rotator Elbow with Storz inlet and 4.5” (F) NH swivel adapter
Component Weights:
Daspit Tool™ Tank Clamp = 89 lbs
Accessory Component Weights:
90˚ Aluminum Rotator Elbow - 4.5” (F) NH Swivel x 5” Storz = 22 lbs 30˚ Aluminum Rotator Elbow - 4.5” (F) NH
Swivel Elbow x 5” Storz = 9 lbs
4” Aluminum Tiller Bar Monitor w/ 4.5” (F) NH Swivel inlet = 43 lbs
4” Aluminum Dual Hand Wheel Monitor - 4.5” (F) NH Swivel inlet = 50 lbs
Ranger™ 1.5 Nozzle = 22 lbs
Applications:
Sunken roof
Rim Seal fire
Vapor Suppression/Mitigation
Options:
3” Aluminum Waterway Monitor w/Tiller Bar Control
250-1,000 gpm Automatic Nozzle
4” Aluminum Waterway Monitor w/Dual Hand Wheel Control
500-2,000 gpm Automatic Nozzle
Rim Mounted Model
Truck Mounted Model
“Throw-Down” Model
Tank Mount Standard Unit
For US and Foreign Patent and Trademark information, please refer to page IP2
Monitors
Product:
Daspit Tool - Truck Mount™
For US and Foreign Patent and Trademark information, please refer to page IP2
Monitors
Product:
Daspit Tool™ - Throw Down Model
Component Weights:
Daspit™ Tool Throw Down Mount = 113 lbs
8 Stabilizing stakes = 64 lbs
47.875”
For US and Foreign Patent and Trademark information, please refer to page IP2
Monitors
Product:
Alpha MA-HV4 Monitor
Description:
Rugged lightweight aluminum construction 4” ID full flow monitor with “Quick Acting” Tiller-Bar control for vertical
and horizontal movement. Red powder coat anodized aluminum. The single 4” full-flow waterway with internal turning vanes
is designed to provide maximum efficiency. The “Easy-Lock” brake system insures that the nozzle position “stays put” with
the simple twist of an ergonomically designed locking bar. Monitor features a 3.50” (M) NH outlet and a 4.0” 150# ASA
flat-faced flange inlet. Horizontal articulation is 360˚ and vertical travel is 75˚ up and -25˚ down.
Monitors
Product:
Alpha-E Tiller Bar Montior - 3”
Description:
Rugged, corrosion resistant brass construction; unique configuration flows up to 1250 gpm; compact - just 16” high; 3”
NPT female, 3” or 4” 150# ANSI flange; vertical movement 90 degrees above horizontal to 45 degrees below; full, continuous
360 degree rotation; rugged, stainless steel lock hardware; brass balls in all swivel joints; grease fittings for easy lubricaion;
durable acrylic urethane finish
Alpha-E Tiller Bar
Monitor
Waterway
Inlet
Discharge
Material
Vertical Travel
Horizontal
Rotation
3”
3”-4” Flanged
2.5” NH(M)
Cast Brass
90º
360º
Monitors
Product:
“SharpShooter Four” Tiller Bar -4”
Description:
Superior grade 4” I.D. waterway monitor with tiller bar
control for vertical and horizontal movement. Designed for
use in corrosive atmospheres that require the dependability
and durability of an all brass monitor. Single waterway
with turning vanes providing excellent projection for water
or foam streams. Flows up to 1,500 gpm.
Tiller bar control with brake band swivels, adjusts, then
locks at the vertical and horizontal position. Vertical setting
is from minus (-) 10º to plus (+)70º. Full 360 degree horizontal travel. Painted red polyurethane finish. 3.5”NH (M)
discharge threads. Base -4” 150 # ASA flange.
Sharpshooter
Four
Waterway
Inlet
Discharge
Material
Vertical Travel
Horizontal
Rotation
4”
4” Flange
3.5” NH(M)
Cast Brass
80º
360º
Monitors
Product:
“SharpShooter Four” Dual Handwheel -4”
Description:
Superior grade 4” I.D. waterway monitor with dual handwheel/worm
gear operation for vertical and horizontal movement. The ultimate monitor
for portable applications or for fixed installations where precise and posi
tive control are needed. Designed for use in corrosive atmospheres that
require the dependability and durability of an all brass monitor. Single
waterway with turning vanes providing excellent projection for water or
foam streams. Flows up to 1,500 gpm.
V erti cal handwheel adj usts traj ectory f rom mi nus ( -) 10º to pl us ( +) 90º.
Horizontal handwheel allows for full 360º rotation. Painted red polyure
thane. 3.5”NH (M) discharge threads. Base -4” 150 # ASA flange.
Sharpshooter
Four
Waterway
Inlet
Discharge
Material
Vertical Travel
Horizontal
Rotation
4”
4” Flange
3.5” NH(M)
Flange
Cast Brass
100º
360º
Monitors
Product:
Alpha-SHW Single HandWheel Monitor - 3”
Description:
Rugged, cast brass construction • Full 3.0” unobstructed waterway • FLows up to 1250 GPM • Handwheel driven worm
gear fully enclosed and protected from the elements • Stainless steel worm • Vertical travel from 70˚ above to 70˚ below
horizontal • Gear holds vertical position wherever it is stopped • Four ball races with bronze balls and grease zerks for easy
lubrication • Full 360˚ rotation with positive twist lock • 2.5” male outlet • FM Approved • See chart for base options • Finish
red urethene enamel.
Model
Alpha-SHW
Waterway
Inlet
Discharge
Material
Vertical Travel
Horizontal
Rotation
3”
3” or 4” Flange
2.5” NH(M)
Cast Brass
90º
360º
Monitors
Product:
Spectrum “Mini- Monitor” -2”
Description:
Designed for use in corrosive atmospheres that require the
dependability of an all brass monitor. Suitable for most industrial
environments. Flows up to 300 gpm @ 100 psi. Full 2” I.D. waterway, efficiently designed to minimize pressure drop. 2” NPT female
inlet base, 1.5” NH male discharge tip. Tiller bar control handle with
rubber grip. Vertical (110º) and horizontal (360º) adjustments with
positive quarter-turn locking handles. Natural brass finish.
Model
Mini Monitor
Waterway
Inlet
Discharge
Material
Vertical Travel
Horizontal
Rotation
2”
2”NPT (F)
1.5” NH(M)
Cast Brass
110º
360º
Oscillating Monitors
Product:
Spectrum High Flow Model 4 Oscillating Monitor Tiller Bar Control
Description:
For flows between 750 - 1500 gpm. Spectrum High Flow Model
4 water-powered oscillating monitor is constructed of predominantly
corrosion-resistant materials. Cast brass monitor body with stainless steel trim. 4” I.D. waterway with turning vanes. Controls provided for adjusting vertical trajectory as well as horizontal position.
Reciprocating motion is generated by a two-way high performance
hydraulic actuator. Oscillation is accomplished through the use of
plated sprockets and a heavy duty drive chain. Standard arc of oscillation is from 0-90˚ and speed of oscillation is from 0-40˚ per second.
Vertical trajectory is from minus (-)10˚ to plus (+)70˚. Standard inlet
flange - 4” 150# ASA RF Flange. Monitor is to be used with either
a non air-aspirating or air-aspirating nozzle. Standard 3.5” NH (M)
discharge. Oscillating mechanism is Factory Mutual Approved - File
No. J.I.1R6A3.AF.
(Nozzle shown for
reference only)
Model
Flow @ 100 PSI
Inlet
Discharge
Water I.D.
High Flow Model 4
Tiller Bar Control
Between 750-1400 gpm
4” 150# ASA RF flange
3.5” NH (M)
4”
* Minimum operating pressure = 50 psi
Oscillating Monitors
Product:
Spectrum Medium Flow Model 4
Oscillating Monitor
Description:
For flows between 150-750 gpm. Spectrum Medium Flow
Model 4 low profile water-powered oscillating monitor features a
super-compact design, as well as predominantly corrosion resistant
materials of construction. Reciprocating motion is generated by a
two way high performance hydraulic actuator. Oscillation is accomplished through the use of plated sprockets and a heavy duty drive
chain. Arc of oscillation is from 0-185º and speed of oscillation is
from 0-40º per second. Nozzle elevation is from 10º below to 70º
above horizontal. Single brass 3” I.D. waterway with turning vanes
provided with positive horizontal and vertical locks. Standard inlet
flange - 4” 150# ASA RF Flange. Monitor can be used with either a
non air-aspirating or air aspirating nozzle. Oscillating mechanism is
Factory Mutual Approved - File No. J.I.1R6A3.AF.
(Nozzle shown for
reference only)
Model
Flow @ 100 PSI
Inlet
Discharge
Water I.D.
Medium Flow Model 4
Between 150-750 gpm
4” 150# ASA RF flange
2.5” NH (M)
3”
* Minimum operating pressure = 50 psi
Oscillating Monitors
Product:
Spectrum Marine Grade Model 4
Oscillating Monitor
Description:
For flows between 150-750 gpm. Spectrum Marine Grade Model 4 low profile water-powered oscillating monitor features a super-compact design, as well as construction of totally corrosion resistant materials to include inlet flange, enclosure
and drive mechanism, sprocket and chain — all manufactured in 316 Stainless Steel. Reciprocating motion is generated by a
two way high performance hydraulic actuator. Oscillation is accomplished through the use of plated sprockets and a heavy
duty drive chain. Arc of oscillation is from 0-185º and speed of oscillation is from 0-40º per second. Nozzle elevation is from
10º below to 70º above horizontal. Single brass 3” I.D. waterway with turning vanes provided with positive horizontal and
vertical locks. Standard inlet flange - 4” 150# ASA RF Flange. Monitor can be used with either a non air-aspirating or air
aspirating nozzle. Oscillating mechanism is Factory Mutual Approved - File No. J.I.1R6A3.AF.
Model
Flow @ 100 PSI
Inlet
Discharge
Water I.D.
Marine Grade
Model 4
Between 150-750 gpm
4” 150# ASA RF flange
2.5” NH (M)
3”
* Minimum operating pressure = 50 psi
Oscillating Monitors
Product:
Spectrum Low Flow Model 4 Oscillating Monitor
Description:
For flows between 100-350 gpm. Spectrum Low Flow Model 4 low
profile water-powered oscillating monitor features a super-compact design,
as well as corrosion resistant materials of construction. Reciprocating
motion is generated by a two-way high performance hydraulic actuator.
Oscillation is accomplished through the use of plated sprockets and a heavy
duty drive chain. Arc of oscillation is from 0-185º and speed of oscillation
is from 0-40º per second. Nozzle elevation is from 30º below to 80º above
horizontal. Single brass 2” I.D. waterway. Provided with positive horizontal
and vertical locks. Standard inlet flange -4” 150#. Monitor can be used with
either a non air-aspirating or air-aspirating nozzle. Oscillating mechanism is
Factory Mutual Approved - File No. J.I.1R6A3.AF.
(Nozzle shown for
reference only)
Model
Flow @ 100 PSI
Inlet
Low Flow Model 4
Between 100 - 350 gpm
4” 150# ASA RF flange
* Minimum operating pressure = 50 psi
Discharge
1.5” NH(M)
Water I.D.
2”
Oscillating Monitors
Product:
“Durham” Oscillating Monitor Conversion Kit
Description:
The Durham Conversion Kit transforms an existing manual station monitor into an oscillator. Designed for use with most 2.5” or 3”
I.D. single waterway monitors, flowing up to 750 gpm. Upgrading
foam or water monitor coverage in any area is now as easy as unbolting the existing monitor and inserting the conversion kit between
the flanges. Oscillating mechanism is identical to the one used on
the Spectrum Model 4 Oscillating Monitor and is Factory Mutual
Approved - File No. J.I.1R6A3.AF. Standard inlet and discharge
flange is -4” ASA RF Flange 150#. Optional inlet and discharge
flanges available upon request.
Model
Flow @ 100 PSI
Inlet
Discharge
Water I.D.
Durham
Conversion Kit
up to 750 gpm
4” 150# ASA RF flange
4” 150# ASA RF flange
2.5” or 3”
Remote Control Monitors
Product:
Spectrum Direct-Mounted Electric Actuated Monitor
Description:
Flows water or foam from 500 to 6,000 gpm. The Spectrum Direct-Mounted
Electric Actuated High Volume/Remote Control Monitor has a programmable
oscillation capability, but may also be overridden with a matched Hydro-Foam™
nozzle operated remotely through the use of a joystick and switches on a consolidated control panel. Manual operation can also be accomplished locally through
the use of handwheels. Foam concentrate can be proportioned at the nozzle
through the use of a jet ratio controller and atmospheric concentrate storage tank.
All electric actuators are reversible, NEMA 7 explosion proof, refinery grade,
F.M. Approved and C.S.A. certified. No external controls, starters, or starters in
motor control center are needed. Only power and control conductors are required.
Monitor can be programmed to “return to home” position (horizontal, vertical,
nozzle to wide angle fog) after use, automatically, whether P.L.C. controlled or
hard wired.
Two direct mounted electric actuators with speed reducing gear drives installed on the motor enable remote control of
horizontal position, as well as vertical trajectory. Field-adjustable limit switches on each actuator allow 340º horizontal rota
tion and from minus (-)70º to plus (+)70º vertical travel. Monitor traversing speed is a least 10º per second. A third directmounted electric actuator enables remote operation for the nozzle’s discharge pattern, from wide fog to straight stream.
Weather protective cowlings are provided over all gears and shafts. Monitor and controls are designed for minus
(-)20º F operation. Maximum working pressure is 200 psi.
Stainless Steel monitor (waterway) with red epoxy finish. Includes lifting lug for handling and mounting. Stainless steel
swivels with stainless steel ball bearings. Steel/bronze gears. Nickel plated brass shaft. Standard motor voltage is 480/3/60
Standard Control voltages is 120 Vac. Other voltages are available when required.
Model
Nominal flow range
Inlet
Pressure Drop
4” Waterway Monitor
500-1500 gpm
4” flange
@ 1500 gpm-9 psi
6” Waterway Monitor
1500-3000 gpm
6” flange
@ 3000 gpm-7 psi
8” Waterway Monitor
2500-6000 gpm
8” flange
@ 6000 gpm-10 psi
Remote Control Monitors
Spectrum Direct-Mounted
Electric Actuated Monitor
Remote Control Monitors
Product:
Spectrum Electro/Hydraulic Actuated Monitors
Description:
Flows water or foam from 500 to 3,000 gpm. The Spectrum Electro/
Hydraulic High Volume/Remote Control Monitor is operated remotely through
the use of a joystick and switches on a consolidated control panel. Manual operation can also be accomplished locally through the use of handwheels.
Two hydraulic actuators installed on the monitor enable remote control of
horizontal position, as well as vertical trajectory. Maximum travel is limited to
340 degrees horizontal travel and from minus (-)70 degree to plus (+)70 degree
vertical travel. Monitor traversing speed is at least 8 degrees per second. A
direct-mounted linear hydraulic actuator enables remote operation for the
nozzle’s discharge pattern, from wide fog to straight stream. Weather protective
cowlings are provided over all gears and shafts.
Equipped with a standard non air aspirating fog-to-straight stream nozzle.
With a matched Hydro-Foam™ nozzle, foam concentrate can be proportioned at
the nozzle through the use of a jet ratio controller and atmospheric concentrate
storage tank.
Stainless steel monitor (waterway) with red epoxy finish. Includes lifting
lug for handling and mounting. Stainless steel swivels with stainless steel ball
bearings. Steel/bronze gears. Nickel plated brass shaft. Anodized aluminum
fog/straight stream nozzle.
Model
Nominal flow range
@ 100 psi
Inlet
Pressure Drop
4” Waterway Monitor
500-1500 gpm
4” flange
@ 1500 gpm-9 psi
6” Waterway Monitor
1500-3000 gpm
6” flange
@ 3000 gpm-7 psi
Remote Control Monitors
Spectrum Electro/Hydraulic
Actuated Monitor
Monitor Accessories
Product:
Hydrant Monitor Stand
Description:
For mounting monitor station (Hydro-Foam™ or water only)
onto any fire hydrant. Standard configuration: water inlet is 2.5”
NH(F) brass swivel; 3” waterway with 90 degree elbow; bolted vertical support stanchions; flanged discharge (specify either 3” or 4”
150# ASA). Red polyurethane finish.
Monitor Stand shown with Hydrant and Optional
Monitor and Nozzle.
Note: hydrant not included.
Ranger3™ Nozzle
Product:
Ranger3™ Monitor/Nozzle
The Ranger3™, featuring “Smart Nozzle” Technology, was designed for today’s
Industrial fire fighting and protection needs. Hazards involving flammable liquids in
storage and liquids under pressure have met their match with the New Millennium
Equipment from Williams Fire & Hazard Control, Inc®.
The Ranger3™ nozzle combination is capable of not only self-educting foam
concentrate, but can do so while maintaining a nearly constant pressure (+/-10%)
and a constant foam percentage (1% or 3% selectable) regardless of the flow rate.
Discharge flow rates from 1000-3000 USGPM (3800-11356 LPM) can be water only,
Hydro-Foam™ (using jet pumps or automatic constant/selectable metering) or HydroChem™ for extinguishing liquids and gases under pressure.
Advancing the Fire Fighter’s Ability with Equipment and
Knowledge.
This “Hybrid” nozzle has the unique capability to perform as an automatic pressure or fixed gallonage nozzle. During
automatic operation the nozzle will respond to varying flows to maintain a nearly constant tip pressure, thus maximizing effective range for a given discharge flow. Once the nozzle reaches the fixed gallonage set point (1000-3000 GPM), it performs
as a conventional fixed gallonage nozzle. This is desirable for foam proportioning operations on storage tank fires or other
hazards requiring specific application rates. This nozzle is capable of Hydro-Foam™ proportioning at rates up to 3000 GPM
@ 3%. It can automatically maintain a nearly constant foam percentage (1% or 3%) throughout the entire flow range while
self-educting. It can optionally be configured to proportion foam from remote locations using jet pump technology (thus forfeiting the constant/selectable metering feature). The extensive Ranger3™ options list allows this nozzle to be Hydro-Chem™
capable (without Hydro-Foam™ capability) with PKW™ flow rates from 25 lbs/s to 50 lbs/s. Pattern control from straight
stream to full fog is accomplished via a full wrap-around handle attached to the outer sleeve.
*See Williams’ Nozzle Range Chart on page D5
Standard Features List:
Dual Mode Automatic/Fixed Operation
Fixed Gallonage plugs: 1K, 2K, 3K
Hydro-Foam™ Constant/Selectable
1% or 3% Nozzle
Wrap-around handle design for pattern control
For US and Foreign Patent and Trademark information, please refer to page IP2
Options:
Hydro-Chem™ Tip conversion
Choke tubes (25 and 50 lbs/s)
Dry chemical manifolds (4 inlet or 7 inlet)
1.5JP30 Jet Pump w/stinger (one)
2.0JP60 Jet Pump w/stinger (one)
2.5” x 10 Dry Chemical Hose
3-2.5” FNST x 3.0” MNPSH Siamese
(Jet to Monitor Supply)
1-2.5” FNST x 3-1.5” MNST Wye
(Jet Pump Supply)
Hydro-Foam™ Nozzles
Product:
Ranger Lightning
Description:
Ranger Lightning is the latest in a series of innovative lightweight Hydro-Foam™, self-contained foam systems as defined by
NFPA standard 1901, Section A-8-3.22.
This rugged design is the first in a series of master stream nozzles to feature Williams Fire & Hazard Control’s Armor-Lyte™
construction.
Armor-Lyte™ is a composite of lightweight, non-corrosive materials that provide years of trouble-free service.
Features
• Self-educts foam concentrate directly from an atmospheric source.
• Selectable gallonage with matched foam proportioning of 1% and 3% at 350, 500, or 750 gpm at 100 psi operating
pressure.
• Flush setting as recommended per NFPA 1964.
• Change flow rate, proportion rate, or flush without the need to
shutdown.
• Positive lock feature for rate selection!
• Self-contained internal stream straightner to maximize range!
• T-handle for pattern control for full fog to straight stream.
• Complete unit weighs only 6 lbs!
• 1.00” MNPT foam inlet port.
• 2.50” FNST Swivel inlet connection.
Options
• Available in Hydro-Chem and Master Stream (water only) versions.
• Actuated pattern control in 12vdc, 24vdc, pneumatic, or hydraulic.
• Nickel-plated brass swivel inlet.
• Nozzles available at: .5% & 1% proportioning selections
Special inlet threads available upon request.
Inlet view
Selectable gallonage with matched foam
proportioning of 1% and 3%
Hydro-Foam™ Nozzles
Product:
HF Ranger™ “Select” - Automatic/Constant Metering
Foam Nozzle
Description:
Introducing the most advanced foam fire fighting nozzle ever made! The
Hydro-Foam™ Ranger™ “Select” Nozzle combines the effective range of
an automatic nozzle, while incorporating the exclusive combination of self
educting/selectable “constant metering” foam proportioning. It is capable of
accurate foam proportioning (Selectable 1% or 3%) over a broad range of
flows (250 - 1500 gpm), while maintaining automatic control of tip pressure
(100 psi +/- 10%) over the entire flow range. This constant nozzle pressure
capability maximizes the effective discharge reach for any given flow. The
discharge pattern is adjustable from full fog to straight stream. Constructed of
anodized aluminum with “wrap around” control handle and protective rubber
bumper. Water inlet is available in nickel plated brass as an option. Manually
operated nozzle is available with automatic controls: 12v; 24v; or hydraulic.
Options:
• 2.5” or 3.5” swivel
• Nickel plated brass swivel
• 12v, 24v or hydraulic pattern activation
Model
Ranger™ Hydro-Foam™
Ranger™ HFR 1.0 M 2.5*
Ranger™ HFR 1.5 M 3.5*
Water Inlet *
2.5” (F) NH Swivel
3.5” (F) NH Swivel
Foam Concentrate Inlet *
1.50 M/NPT
w/1.5” x 8 Flexible Pickup
Hose & 1.5” Rigid PVC
Drum “Stinger”
2.00 (M) NPT
w/2” x 8 Flexible Pickup
Hose & 1.5” Rigid PVC
Drum “Stinger”
Foam/Water Flow
(@ 100 psi)
250-1000 gpm
250-1500 gpm
Proportioning
(Selectable)
1% or 3%
1% or 3%
Application
Class “B” Liquid Fires
*Refer to page D14 for complete part# and ordering information
For US and Foreign Patent and Trademark information, please refer to page IP2
Hydro-Foam™ Nozzles
Product:
Constant Flow Ranger™ 750, 1000, 1250 & 1500 GPM
Description:
Water powered nozzle system that proportions and delivers either water
or foam to the hazard area. Fully adjustable from straight stream to full fog.
Constructed of hard anodized aluminum alloy with stainless steel trim. Water inlet
is available in nickel plated brass as an option. Nozzle is supplied with flexible 8
ft. pick-up hose with 1.5” rigid pvc drum “stinger”. Built in select feature provides
proportioning at either 1% or 3%. Fixed foam proportioning may be proportioned
directly from atmospheric source. Manually operated nozzle is also available with
automatic controls: 12v; 24v; or hydraulic. Optional “Jet Pump” is available for
remote proportioning.
Nominal Flow
@100psi
K-Factor
Nominal Range
@ 100psi
(straight stream)
Water inlet standard
Concentrate Inlet
Proportioning
without jet
Fixed Ranger™
750
Fixed Ranger™
1000
Fixed Ranger™
1250
Fixed Ranger™
1500
750 gpm
1000 gpm
1250 gpm
1500 gpm
75
100
125
150
215 ft.
250 ft.
260 ft.
275 ft.
2.5”NH (F)
2.5”NH (F)
3.5”NH (F)
3.5”NH (F)
1.5” NPT(M)
1.5” NPT(M)
2” NPT(M)
2” NPT(M)
1% / 3%
1% / 3%
1% / 3%
1% / 3%
For US and Foreign Patent and Trademark information, please refer to page IP2
Monitor Foam Nozzles, Air Aspirating
Product:
Hydro-Air Foam Monitor Nozzles, Medium (Not shown)
& Big Body
Description:
Exclusive super-compact, air aspirating foam nozzle with adjustable stream
from full fog to straight stream! Has the appearance of a standard fog/straight
stream monitor nozzle, yet the “Hydro-Air” venturi provides foam expansion ratios
of up to 6:1 by actually inducting air into the center of the master stream. Medium
Body Nozzles are available in lightweight anodized aluminum. Standard flow
rates from 350 to 1500 gpm at 100 psi. As an option, nozzles can be factory modified to flow from 200 to 1500 gpm at specific inlet pressures.
Big Body “Ranger™”
Hydro-Air Nozzle
750-1500 GPM
Air Inlet
Foam Inlet
(F) NH Swivel
Medium Body
HA-350
Medium Body
HA-500
Medium Body
HA-700
Big Body
HA-1000*
Big Body
HA-1250
Big Body
HA-1500*
Flow @100 psi
350
500
700
1,000
1,250
1,500
Standard inlet
2.5”NH(F)
2.5”NH(F)
2.5”NH(F)
2.5” or 3.5”
2.5” or 3.5”
2.5” or 3.5”
Material
Brass
Brass
Brass
Aluminum
Aluminum
Aluminum
*Refer to page D14 for complete part# and ordering information
For US and Foreign Patent and Trademark information, please refer to page IP
Monitor Nozzles
Product:
Ranger™ Automatic - Master Stream Nozzle
Description:
The Ranger™ Automatic Master Stream Nozzle is made for use
on monitors, ladder pipes, deluge guns and aerial platforms. This nozzle’s uniquely-designed constant-pressure feature assures maximum
effective reach for either water or foam/water solution. The tip pressure is automatically controlled to maintain a constant pressure (100 psi
+/- 10%) over the nozzle flow range, which is from 250 gpm to 1,500
gpm.
(Other maximum flow stops available). The nozzle pattern is
adjustable from full fog to straight stream. Constructed of anodized
aluminum with exclusive “wrap-around” control handle and protective bumper. Water/foam solution inlet is available in nickel plated brass
as an option. Nozzle is used in conjunction with an independent foam
proportioning system when applicable. Manually operated nozzle is also available with automatic controls: 12v; 24v; or hydraulic.
Model
Nozzle Pattern
Control
Solution Inlet*
Solution Rate
(GPM)
Material of
Construction
MSR1.O M 2.5
Manual
2.5”
250-1,000
Anodized Alum.
MSR1.5 M 3.5
Manual
3.5”
250-1,500
Anodized Alum.
MSR1.O A 2.5
12 vdc electric
2.5”
250-1,000
Anodized Alum.
MSR1.5 A 3.5
12 vdc electric
3.5”
250-1,500
Anodized Alum.
MSR1.O B 2.5
24 vdc electric
2.5”
250-1,000
Anodized Alum.
MSR1.5 B 3.5
24 vdc electric
3.5”
250-1,500
Anodized Alum.
MSR1.O H 2.5
Hydraulic
2.5”
250-1,000
Anodized Alum.
MSR1.5 H 3.5
Hydraulic
3.5”
250-1,500
Anodized Alum.
For US and Foreign Patent and Trademark information, please refer to page IP2
Hydro-Chem™ Technology
The most effective method for extinguishing large pressure and flowing fuel fires.*
By using foam solution as the means to propel, Hydro-Chem™ Systems project dry chemical approximately three to four
times farther than that of conventional dry chemical equipment. Hydro-Chem™ technology gives the firefighter a safer and
more efficient integrated system of delivering dry chemical onto large pressure and flowing fuel fires.
In operation, ground fires are extinguished using foam only. The foam solution applied then “ties-up” or harnesses the
three dimensional fire, greatly reducing flame intensity. After this reduction in heat, dry chemical is then injected into the
foam stream, resulting in a more proficient extinguishment of the fire. Each system is used in conjunction with customerprovided dry chemical storage equipment.
*Not normally intended for use on liquefied petroleum gas fires.
For US and Foreign Patent and Trademark information, please refIP2
Hydro-Chem™ Nozzle
Product:
HC Ranger™-Automatic Hydro-Chem™ Nozzle
Description:
The Hydro-Chem™ Ranger™ Nozzle combines the effective range
of an automatic nozzle, while incorporating the dry chemical/foam solution delivery capabilities of Hydro-Chem™ Technology. Designed to
extinguish three dimensional and oxygenated fuel fires. This unique
nozzle projects dry chemical (@ 20 lbs./sec.) through the center of the
foam/water stream, resulting in an effective range not possible with conventional dry chemical equipment. The constant pressure feature assures
maximum effective reach of the foam/water solution. The tip pressure
is automatically controlled to maintain a constant pressure (100 psi
+/- 10%) over the nozzle flow range, which is from 250 gpm to 1,500
gpm. The discharge pattern is adjustable from full fog to straight stream.
Constructed of anodized aluminum, with “wrap-around” control handle and
protective rubber bumper. Foam solution/water inlet is available in nickel
plated brass as an option. Nozzle is used in conjunction with an independent foam proportioning and dry chemical delivery system.
Basic Model# *
Nozzle Pattern
Control
Water Solution Inlet*
Solution Rate (GPM)
Material of
Construction
HCR1.O M 2.5
Manual
2.5”
250-1,000
Anodized Alum.
HCR1.5 M 3.5
Manual
3.5”
250-1,500
Anodized Alum.
HCR1.O A 2.5
12 vdc electric
2.5”
250-1,000
Anodized Alum.
HCR1.5 A 3.5
12 vdc electric
3.5”
250-1,500
Anodized Alum.
HCR1.O B 2.5
24 vdc electric
2.5”
250-1,000
Anodized Alum.
HCR1.5 B 3.5
24 vdc electric
3.5”
250-1,500
Anodized Alum.
HCR1.O H 2.5
Hydraulic
2.5”
250-1,000
Anodized Alum.
HCR1.5 H 3.5
Hydraulic
3.5”
250-1,500
Anodized Alum.
*Refer to page D14 for complete part# and ordering information
For US and Foreign Patent and Trademark information, please refer to page IP2
Hydro-Chem™ Nozzles
Product:
Handgun Hydro-Chem™ Variable Flow Nozzle
Description:
Dual-agent pistol grip handline nozzle incorporates a foam solution or water application with simultaneous Hydro-Chem™ Technology
which projects dry chemical through the center of the foam/water stream
to achieve ranges not possible with conventional equipment. Used in conjunction with a separate foam proportioning system.
The foam/water stream is adjustable from full fog to straight stream.
Collar mounted ring adjustment allows quick selection of 60, 95 or 125
gpm flow rates — also features a flush setting. The nozzle features separate flow valves for water/foam and dry chemical operations. Constructed
of hard anodized aluminum alloy. Total nozzle weight 7 lbs.
Options Include:
Three inlet valved dry chemical inlet manifold (not shown); flat lay
dry chemical inlet hose, 1.5” x 50’, coupled 1.5 (M) NH; “cross-over”
adapter (for Ansul 350 lb wheeled unit) 1.25” (F) NPSH X 1.5” (M) NH
NOTE: 1.0” NH (F) Swivel connections also available for
water/foam and dry chemical
* Varies depending on dry chemical delivery system and
length of hose lay
For US and Foreign Patent and Trademark information,
please refer to page IP2
Part #
Water/Foam Flow
HCHG-S
60, 95, 125 gpm
Dry Chemical Flow*
5, 7.5, 10 lbs / sec
Water/Foam Solution
Inlet NH (F)
1.5” Swivel NH (F)
Dry Chemical Inlet
1.5” Swivel NH (F)
Ranger™ AUTOMATIC NOZZLE
HF / HC / MS PART NUMBERING SYSTEM
R
VERSION:
HF HC MS -
-
-
-
-
Hydro-Foam™
Hydro-Chem™ (1.5” (F)NPT CHEMICAL INLET STD.)
MASTER STREAM
FLOW RANGE:
1.0
250-1000 USGPM - Automatic
1.5
250-1500 USGPM - Automatic
X
Special - Fixed Flow or Automatic
(Requires Engineering Approval - Specify As Option)
PROPORTIONING METHOD:
N
None (Required for HC & MS Versions)
F
Fixed Rate (HF Only)
S
Selectable Rate (HF Only)
J
Jet Pump (HF Only - Requires Engineering Approval Limited to 750 GPM for 3% Proportioning)
PROPORTIONING RATE:
0
None (Required for HC & MS Versions)
.5
.5% (Fixed Only) (1” MNPT Foam Inlet Std)
1
1% (Fixed), .5% (Selectable) (1.5” MNPT Foam Inlet Std)
3
3% (Fixed), 1-3% (Selectable) (2” MNPT Foam Inlet Std)
X
Special (Requires Engineering Approval)
PATTERN CONTROL:
M
Manual
A
12VDC Actuated
B
24VDC Actuated
H
Hydraulic
X
Special
INLET CONNECTIONS:
2.5
2.5” FNST (Standard on 1.0 Flow Range)
3.5
3.5” FNST (Standard on 1.5 Flow Range)
64
64MM (2.5”) FBSP
89
89MM (3.5”) FBSP
X
Special (Requires Engineering Approval)
OPTIONS:
0
1
2
3
4
5
6
7
A
F
X
None
90˚ Swivel w/1.5” FNPT Foam/Chemical Inlet Port (Not recommended for HF1.5)
90˚ Swivel w/1.5” FNST Swivel Foam/Chemical Inlet Port (Not recommended for HF1.5)
Nickel Plated Brass Inlet Nut in Lieu of Standard Anodized Aluminum
Straight 1.5” FNST Swivel Foam/Chemical Inlet Port (Not recommended for HF1.5)
Straight 1.5” FNPT Rigid Foam/Chemical Inlet Port (Standard on HC - Not recommended for HF1.5)
Male Cam-Lock Foam/Chemical Inlet Port (Same as Standard Size for Nozzle Configuration)
Manual ON/OFF 1-3% Metering Valve
Automatic w/Maximum Flow Stop (Requires Engineering Approval)
Fixed Flow Maximum Stop Non-Automatic (Requires Engineering Approval)
Special (Requires Engineering Approval)
NOTE:
All “X” Selections Require Engineering Approval Prior to Ordering —
A Detailed Description Must be Provided When Placing Order
Monitor Nozzles
Product:
Monitor Nozzle - “BTM” Series
Description:
Standard industrial grade master stream nozzle. Fully adjustable from
straight stream to full fog. Cast brass construction. Standard flow rates of 350,
500, and 700 gpm at 100 psi nozzle pressure. As an option, nozzle can be factory modified to any flow between 100 to 700 gpm at 100 psi (i.e. any K Factor
between 10 and 70). Abbreviated style cast control handles. Standard jam nut
locks foam or water stream at desired pattern. 2.5” NH (F) rigid inlet.
Model
Flow @100 psi
K-Factor
Inlet
Range Straight
Stream
Material
BTM-350
350
35
2.5” NH (F)
150 ft.
Cast Brass
BTM-500
500
50
2.5” NH (F)
190 ft.
Cast Brass
BTM-700
700
70
2.5” NH (F)
200 ft.
Cast Brass
Monitor Nozzles
Product:
Premium Monitor Nozzle - “Big Tee”
Description:
Premium grade industrial master stream nozzle with exclusive
“flush” feature. In flush position, nozzle will purge particulates up
to .25” diameter. Fully adjustable from straight stream to full fog.
Large composite rubber covered brass handles for positive stream
control. All brass construction. Standard flow rates are 350 and
500 at 100 psi nozzle pressure.
Model
Flow @100 psi
K-Factor
Inlet
Range Straight
Stream
Material
BT-350
350 gpm
35
2.5” NH (F) Swivel
135 ft.
Cast Brass
BT-500
500 gpm
50
2.5” NH (F) Swivel
150 ft.
Cast Brass
Monitor Nozzles
Product:
High Volume Monitor Nozzle - WBB “Big Boy”
Description:
High-volume, industrial-grade, master stream nozzle. Fully adjustable from straight stream to full fog. Cast brass construction. Standard
flow rates of 750, and 1000 gpm at 100 psi. Abbreviated style cast
control handles. Standard jam nut locks foam or water stream at desired
pattern. Available with either 2.5” or 3.5” NH (F) inlet.
Model
Flow @100 psi
K-Factor
Inlet(s)
Range Straight
Stream
Material
WBB-750
750 gpm
75
2.5” / 3.5” NH (F)
175 ft.
Cast Brass
WBB-1000
1000 gpm
100
2.5” / 3.5” NH (F)
200 ft.
Cast Brass
Hydro-Foam™ Nozzles
Product:
Hydro-Foam™ Monitor Nozzles —
Small Body LW Series
Description:
Patented water powered nozzle system that proportions and delivers
either water or foam to the hazard area. Fully adjustable from straight
stream to full fog with flows of 150 or 225 gpm. Brass construction with
stainless steel trim. Foam is proportioned directly from an atmospheric
source at 1%, 3% or 6%.
Model #
Flow
Hydro-Foam™ @100psi
Nozzle
Range
@100psi
(straight
stream)
[email protected]
(narrow fog)
Water inlet
Concentrate
inlet
K-factor
Proportioning
Small Body
LW150
150 gpm
110 ft.
60 ft.
1.5”NH
(F)swivel
1”NPT(M)
15
1%, 3% or 6%
Small Body
LW225
225 gpm
115 ft.
65 ft.
1.5”NH
(F)swivel
1”NPT(M)
22.5
1%, 3% or 6%
For US and Foreign Patent and Trademark information, please refer to page IP2
Hydro-Foam™ Nozzles
Product:
Hydro-Foam™ Monitor Nozzles —
Medium Body HF Series - Elkhart
Description:
Patented water powered nozzle system that proportions and delivers either water
or foam to the hazard area. Fully adjustable from straight stream to full fog with
flows of 350 or 500 gpm. Brass construction with stainless steel trim. Nozzle comes
complete with 1” X 8 ft. flexible pick-up hose. Optional 1% or 3% selector provides
dual proportioning capability. Foam concentrate is proportioned directly from an
atmospheric source.
Model #
Hydro-Foam™
Nozzle
Flow
@100psi
Range
@100psi
(straight
stream)
Range
@100psi
(narrow fog)
Water
inlet
Concentrate
inlet
K-factor
Proportioning
HF 350
350 gpm
145 ft.
65 ft.
2.5”NH
(F)swivel
1”NPT(M)
35
1%, 3%
HF 500
500 gpm
155 ft.
75 ft.
2.5”NH
(F)swivel
1”NPT(M)
50
1%, 3%
Hydro-Foam™ Nozzles
Product:
Hydro-Foam™ Monitor Nozzles —
Medium Body LW 700
Description:
Patented water powered nozzle system that proportions and delivers
either water or foam to the hazard area. Fully adjustable from straight
stream to full fog with a flow of 700 GPM @100 PSI. Brass construction
with stainless steel trim. 1% or 3% proportioning. Nozzle is supplied with
a 1” x 8 ft. flexible pick-up hose. Foam is proportioned directly from an
atmospheric storage tank.
Model #
Hydro-Foam™
Nozzle
Flow
@100psi
Range @100psi
(straight stream)
Water
inlet
Concentrate
inlet
K-factor
Proportioning
Medium Body
LW700
700 gpm
160 ft.
2.5”NH
(F)swivel
1”NPT(M)
70
1% or 3%
For US and Foreign Patent and Trademark information, please refer to page IP2
Hydro-Foam™ Nozzles
Product:
Hydro-Foam™ Monitor Nozzles Medium Body LWNS 350, 500 & 750
Description:
Patented water powered nozzle system that proportions and delivers either
water or foam to the hazard area. Fully adjustable from straight stream to
full fog. Brass construction with stainless steel trim. Flows 350, 500 or 750
gpm @100 psi, with 1% or 3% (6% @ 350 and 500 gpm) proportioning. An
optional 1% / 3% (3% / 6% @ 350 and 500 gpm) selector valve provides dual
proportioning. Foam concentrate is proportioned directly from an atmospheric
storage tank or from a remote foam concentrate supply in conjunction with a
matched Jet Ratio Controller at 1% or 3% only. Nozzle is supplied with 1.5”
X 8 ft. flexible pick-up hose.
Model
Hydro-Foam™ Nozzle
LWNS 350
LWNS 500
LWNS 750
Nominal Flow @100psi
350 gpm
500 gpm
750 gpm
Nominal Range @ 100psi
(straight stream)
135 ft.
150 ft.
160 ft.
Water Inlet
2.5”NH (F) Swivel
2.5”NH (F) Swivel
2.5”NH (F) Swivel
Foam Concentrate Inlet
1.5” NPT(M)
1.5” NPT(M)
1.5” NPT(M)
Proportioning
1% / 3% / 6%
1% / 3% / 6%
1% / 3%
For US and Foreign Patent and Trademark information, please refer to page IP2
Handline Nozzles
Product:
HYDROJET HANDLINE NOZZLES
Viper Select Series
Description:
Superior quality fire fighting handline nozzles. Created from performance data gained through extensive research, as well
as from actual field exposure on a multitude of large “fires in anger.”
• Multiple Gallonage/Constant Flow design.
• Compact and Lightweight Design in Extruded “E-Lite” Alloy.
• Molded Composite Rubber Pistol Grip for Precise Control.
• Durable Construction Provides Superior Impact Resistance.
Standard Features Include:
» Constant Flow feature Allows for use with Matched Foam Eductor.
» Factory Installed spinning teeth for Maximum Stream Break-up.
» Combination Full Fog to Straight Stream.
» Independent Pattern Selection with Indication.
» Heavy Duty Rubber Bumper.
» Fully Machined Waterway for Flow Efficiency.
» Excellent for use with ThunderStorm® ATC Foam
Concentrates.
» Horseshoe Shutoff Provides Positive Flow Control.
» Change Flow without Changing Pattern.
» Full Flush Feature.
Model
HydroJet Nozzle
Nominal Flow
Inlet
Length
Weight
SG-3012
30,60,95,125
1.5” NH (F)
8.9”
4.25 lbs.
SG-7515
75,100,125,150
1.5” NH (F)
8.9”
4.25 lbs.
SG-9520
95,125,150,200
1.5” NH (F)
10.6”
6.5 lbs.
Handline Nozzles
Product:
HYDROJET HANDLINE NOZZLES
Viper Select Series
Standard Viper Nozzle
SG-3012
SG-7515
Viper Midrange Nozzle
SG-9520
Air Aspirating Foam Nozzle
Model AFN-1
General Description
Constructed of hard anodized aluminum with stainless steel fasteners
and adjustment rod, this air aspirating foam nozzle offers minimum weight
with durability. Stream pattern is adjustable in the field from an even fan type
to a full straight stream.
Flow rates are specifically tailored to individual protection by the insertion of a pre-engineered stainless steel orifice plate.
Orifice plates can be sized for flows from 250 to 1000 gpm (946 to
3785 Lpm) within K-factors of 35 to 125 based on flowing nozzle inlet pressure. (Monitor friction loss must be deducted from monitor inlet pressure to
use those K-factors.)
Connector is a female swivel, 2.5” – 7.5” TPI NHT.
Ordering Information
Part No.
400200
400336
400380
400326
Description
AFN-1 Nozzle
AFN-1M Nozzle with Lever Operator
AFN-1-SS Stainless Steel Nozzle
AFN-1M-SS Stainless Steel
AFN-1 Nozzle
48.125“
(122.2 cm)
2.5“ - 7.5 NHT
Swivel Coupling
4.5” (11.4 cm)
Diameter
Adjustable Control
Rod
Adjustable Jaws
AFN-1 Nozzle
48.125“
(122.2 cm)
Lever Operator
Control Rod
2.5“ - 7.5 NHT
Swivel Coupling
Nozzle Flow and Range
Pressure
psi
(kPa)
_________
50
(345)
100
(690)
150
(1034)
Flow Rate
gpm (Lpm)
__________
385
(1457)
534
(2021)
656
(2483)
4.5” (11.4 cm)
Diameter
Range at
30° Elev.
ft.
(m)
________
135
(41)
175
(53)
190
(58)
Adjustable Jaws
Range at
22.5° Elev.
ft.
(m)
________
135
(41)
175
(53)
190
(58)
NOTE: Above based on orifice sized for 500 gpm @ 100 psi (1893 Lpm @ 690 kPa).
Range at
15° Elev.
ft.
(m)
________
115
(35)
170
(52)
190
(58)
Range at
0° Elev.
ft.
(m)
________
50 (15)
80 (24)
100 (30)
Air Aspirating Handline Nozzles
Features
•
•
•
•
•
Stainless Steel Construction for Use in
Corrosive Environments
Nominal Flow Rates of 60, 95, or 120 gpm
(227, 360, or 454 Lpm)
Compatible with Ansul PL-60, PL-95, and
PL-120 Line Proportioners
Optional Pistol-Grip Shutoff Available
(Anodized Aluminum)
Lightweight, Portable Design for Maximum
Mobility
23.1”
(58.7 cm)
19”
(48.3 cm)
2.5”
(6.4 cm)
19”
(48.3 cm)
3”
(7.6 cm)
Nozzle
Optional
Shutoff
Application
Ansul (HL) foam handline nozzles can be used with all low expansion foam agents: protein foam, fluoroprotein foam,
and AFFF. These portable, air aspirating nozzles can be used in a variety of flammable liquid hazard areas. Typical applications include use by municipal fire departments and crash-fire-rescue vehicles; or for handline applications around tank farms,
loading racks, aircraft hangars, and chemical plants.
Description
Ansul handline nozzles are available in three sizes (HL-60, HL-95, and HL-120) with or without pistol-grip shutoff. The
nozzles are constructed of stainless steel; the pistol-grip shutoff is anodized aluminum. Lightweight and compact, they maximize fire fighting mobility and ease of use.
Typical Foam Quality/Range Data
Protein/
Fluoroprotein
______
AFFF
____
3%
ARC
_______
Foam
Expansion
Ratio
8:1
10:1
7:1
Drain Time
(25%)
7 min.
3 min.
8 min.
Stream Range
@ 50 psi
(345 kPa)
50 ft.
(15.2 m)
50 ft.
50 ft.
(15.2 m) (15.2 m)
Stream Range
@ 75 psi
(517 kPa)
65 ft.
(19.8 m)
65 ft.
65 ft.
(19.8 m) (19.8 m)
Stream Range
@ 100 psi
(690 kPa)
75 ft.
(22.9 m)
75 ft.
75 ft.
(22.9 m) (22.9 m)
Hose Length/Size Data
Handline Line
Nozzle
Proportioner
_____
__________
Hose
Size
in.
____
Maximum
Hose
Length*
ft.
(m)
________
HL-60
HL-95
HL-120
1.5”
1.5”
1.5”
200
100
100
PL-60
PL-95
PL-120
(61.0)
(30.5)
(30.5)
* Maximum hose length is based on nozzle being elevated a maximum of 8 ft. (2.4 m) above line proportioner.
Ordering Information
The models listed below are provided with 1.5” NHT female inlet threads. Other thread types are available upon request.
The flow rates listed are nominal; see Flow Rate Data for actual flow rates based on inlet pressure.
Part
No.
Description
Approx
Shipping
Weight
lb. (kg)
Part
No.
Description
Approx
Shipping
Weight
lb. (kg)
Part
No.
Description
Approx
Shipping
Weight
lb. (kg)
77796* HL-60 Nozzle
without Shutoff,
60 gpm (227 Lpm)
5
(2.3)
77797* HL-95 Nozzle
without Shutoff,
95 gpm (360 Lpm)
5
(2.3)
77981
HL-120 Nozzle
without Shutoff,
120 gpm (454 Lpm)
5
(2.3)
77792* HL-60S Nozzle
with Shutoff,
60 gpm (227 Lpm)
7
(3.2)
77793* HL-95S Nozzle
with Shutoff,
95 gpm (360 Lpm)
7
(3.2)
78419
HL-120S Nozzle
with Shutoff,
7
(3.2)
Air Aspirating Handline Nozzles
INLET PRESSURE
Flow Rate Data
(kPa)
____
psi
___
(1034)
150
(827)
120
(690)
100
(621)
90
(552)
80
(483)
70
(414)
60
(345)
50
(276)
40
40
(151)
HL-60
50
(189)
60
(227)
70
(265)
80
90 100
(303) (341) (379)
HL-95 HL-120
120
(454)
150 gpm
(568) (Lpm)
FLOW RATE
001224
Foam Nozzles
Product:
Foam Wand
Description:
The Foam “Wand” is designed to expand and deliver foam into remote/
hazardous areas where either logistics or safety considerations dictate that
the foam nozzle be “unattended.” The “wand” delivers high quality foam
onto hard-to-access flammable liquid fires. Flow rate is 95 gpm @ 100
psi (K=9.5). Works in conjunction with a standard 95 gpm inline eductor or other foam proportioning system. Nominal foam expansion is 4:
1. Assembly includes 1.5” NH (F) brass swivel
foam solution inlet; carbon steel distribution piping; foam nozzle; detachable horizontal “standoff”, canvas carrying case.
Typical Application
Foam Wand assembly
Model
Foam Wand
Nominal Flow
@ 100 PSI
K-factor
Inlet
Body
95 gpm
95 gpm
9.5
1.5” NH(F) Swivel
Schedule 40
Carbon Steel
Balanced Pressure Proportioning Systems
Product:
Spectrum Bladder Tanks-Horizontal Configuration
Description:
Spectrum Horizontal Bladder tanks provide dependable and cost
effective foam fire protection for a wide variety of flammable/combustible
liquid hazards. Used in conjunction with either one, or multiple ratio flow
controllers (installed adjacent to the tank), the all-hydraulic balanced pressure proportioning system stores, delivers and proportions foam without
dependence on external foam concentrate pumping. Only water under
pressure is required for system operation.
The Spectrum Horizontal Bladder Tank is a cylindrical carbon steel
ASME pressure vessel containing a flexible polymeric elastomer inner bladder which encapsulates the foam concentrate. This
bladder physically separates stored foam concentrate from the water supply. When the system is activated, water is directed
into the tank shell, which then pressurizes the space between the flexible bladder and the interior tank wall. This water pressure causes the bladder to collapse, which then dispenses foam concentrate out through distribution piping and (ultimately)
into the ratio controller(s). The ratio controller’s modified venturi creates a “metering pressure drop” in the fire water line,
allowing foam concentrate to pass through a fixed orifice plate and enter the fire water piping at the designated proportioning
rate. In installations where the bladder normally is under pressure (wet pipe, reaction, or when the deluge valve is downstream
from the ratio controller), a normally-closed actuated concentrate valve (electric or hydraulic) isolates the foam concentrate
until energized. Interior/exterior finished in red enamel.
Standard Spectrum Bladder tank trim includes:
1. ASME Code Pressure Vessel
2. Flexible Concentrate Bladder
3. Shell Side (water) Vent Valve
4. Bladder (concentrate) Vent Valves
5. Shell Side (water) Fill/Drain Valve
6. Bladder (concentrate) Fill/Drain Valve
7. Water Balancing Nozzle (screened)
8. Vessel Skirt with Anchors
9. Concentrate Discharge Pipe, Perforated
10. Concentrate Discharge Nozzle
11. Lifting Lugs included (not shown)
Spectrum Bladder Options:
12. Sight Gauge Assembly
13. Epoxy Interior/Exterior Finish (For use in
marine or corrosive environments)
14. Pressure Relief Valve (Not Shown)
Horizontal Bladder Tank
Tank Size
A
B
C
D
E
F
G
H
Saddle
Width
Gal.
(L)
in.
(cm)
in.
(cm)
in.
(cm)
in.
(cm)
in.
(cm)
in.
(cm)
in.
(cm)
in.
(cm)
in.
(cm)
100
(379)
16.0
(41)
32
(81)
35.5
(90)
0.75
(1.9)
5
(13)
10
(25)
18
(46)
0.63
(1.6)
3
(7.6)
150
(568)
18.0
(46)
36
(91)
35.0
(89)
0.75
(1.9)
8
(20)
16
(41)
24
(61)
0.63
(1.6)
3
(7.6)
200
(757)
20.0
(51)
40
(101)
44.0
(112)
0.75
(1.9)
8
(20)
16
(41)
24
(61)
0.63
(1.6)
3
(7.6)
300
(1136)
21.0
(53)
42
(107)
46.0
(117)
0.75
(1.9)
11
(28)
22
(56)
30
(76)
0.63
(1.6)
3
(7.6)
400*
(1514)
21.0
(53)
40
(107)
44.5
(113)
0.75
(1.9)
14
(36)
28
(71)
36
(91)
0.75
(1.9)
4
(10.2)
400
(1514)
17.12
(43)
34.25
(87)
36.5
(93)
0.88
(2.2)
17
(43)
34
(86)
42
(107)
0.88
(2.2)
4
(10.2)
500*
(1893)
24.0
(61)
48
(122)
53.0
(135)
0.75
(1.9)
14
(36)
28
(71)
36
(91)
0.75
(1.9)
4
(10.2)
500
(1893)
20.62
(52)
41.25
(105)
43.0
(109)
0.88
(2.2)
17
(43)
34
(86)
42
(107)
0.88
(2.2)
4
(10.2)
600
(2271)
22.5
(57)
45
(114)
49.5
(126)
0.88
(2.2)
17
(43)
34
(86)
42
(107)
0.88
(2.2)
4
(10.2)
700
(2650)
26.0
(66)
52
(132)
56.5
(144)
0.88
(2.2)
17
(43)
34
(86)
42
(107)
0.88
(2.2)
4
(10.2)
800
(3028)
30.62
(78)
61.25
(156)
63.5
(161)
0.88
(2.2)
17
(43)
34
(86)
42
(107)
0.88
(2.2)
4
(10.2)
800*
(3028)
24.0
(61)
48
(122)
52.2
(133)
0.88
(2.2)
20
(51)
40
(102)
48
(122)
1.0
(2.5)
4
(10.2)
900
(3407)
34.12
(87)
68.25
(173)
70.5
(179)
0.88
(2.2)
17
(43)
34
(86)
42
(107)
0.88
(2.2)
4
(10.2)
900*
(3407)
26.0
(66)
52
(132)
57.7
(147)
0.88
(2.2)
20
(51)
40
(102)
48
(122)
1.0
(2.5)
4
(10.2)
1000
(3785)
37.62
(96)
75.25
(191)
77.5
(197)
0.88
(2.2)
17
(43)
34
(86)
42
(107)
1.0
(2.5)
4
(10.2)
1000*
(3785)
28.0
(71)
56
(142)
63.2
(160)
0.88
(2.2)
20
(51)
40
(102)
48
(122)
1.0
(2.5)
4
(10.2)
1100
(4164)
28.0
(71)
56
(142)
60.0
(152)
0.88
(2.2)
23
(58)
46
(117)
54
(137)
1.0
(2.5)
4
(10.2)
1200
(4542)
30.5
(78)
61
(155)
64.5
(164)
0.88
(2.2)
23
(58)
46
(117)
54
(137)
1.0
(2.5)
4
(10.2)
1300
(4921)
32.5
(83)
65
(165)
69.0
(175)
0.88
(2.2)
23
(58)
46
(117)
54
(137)
1.0
(2.5)
4
(10.2)
1400
(5299)
35.0
(89)
70
(178)
73.5
(187)
0.88
(2.2)
23
(58)
46
(117)
54
(137)
1.0
(2.5)
4
(10.2)
1500
(5678)
37.0
(94)
74
(188)
78.0
(198)
0.88
(2.2)
23
(58)
46
(117)
54
(137)
1.0
(2.5)
4
(10.2)
1600
(6057)
39.5
(100)
79
(201)
88.0
(234)
0.88
(2.2)
23
(58)
46
(117)
54
(137)
1.0
(2.5)
4
(10.2)
1700
(6435)
42.0
(107)
84
(213)
87.5
(222)
0.88
(2.2)
23
(58)
46
(117)
54
(137)
1.0
(2.5)
4
(10.2)
1800
(6814)
44.0
(112)
88
(224)
92.0
(233)
0.88
(2.2)
23
(58)
46
(117)
54
(137)
1.0
(2.5)
4
(10.2)
1900
(7182)
46.5
(118)
93
(236)
96.5
(245)
0.88
(2.2)
23
(58)
46
(117)
54
(137)
1.0
(2.5)
4
(10.2)
2000
(7571)
36.0
(91)
72
(183)
72.2
(183)
0.88
(2.2)
29
(74)
58
(147)
66
(168)
1.0
(2.5)
4
(10.2)
2200
(8328)
39.0
(99)
78
(198)
81.7
(208)
0.88
(2.2)
29
(74)
58
(147)
66
(168)
1.0
(2.5)
4
(10.2)
2400
(9085)
42.5
(108)
85
(216)
88.2
(224)
0.88
(2.2)
29
(74)
58
(147)
66
(168)
1.0
(2.5)
4
(10.2)
2600
(9842)
45.5
(116)
91
(231)
94.7
(241)
0.88
(2.2)
29
(74)
58
(147)
66
(168)
1.0
(2.5)
4
(10.2)
2800
(10599)
48.5
(123)
97
(246)
100.7
(256)
0.88
(2.2)
29
(74)
58
(147)
66
(168)
1.0
(2.5)
4
(10.2)
3000
(11356)
52.0
(132)
104
(264)
107.2
(272)
0.88
(2.2)
29
(74)
58
(147)
66
(168)
1.0
(2.5)
4
(10.2)
*To be phased out after June 1996.
H
A
D
E
B
C
F
G
Foam Concentrate Tanks
Product:
Vertical Polyethylene Storage Tanks
Description:
Atmospheric High Density, Cross-Linked Polyethylene Storage Tanks are
an industry standard for storing foam concentrate. They are typically used in
conjunction with pumped balanced pressure systems or self-educting HydroFoam™ monitor stations. Polyethylene is an exceptionally stable and durable
material when used to store foam concentrates. These rotationally molded,
corrosion/impact resistant upright tanks are available in nominal storage
capacities ranging from 55 to 12,000 gallons.
Bill of Materials
Vertical
Poly Tank
1
Pressure Vacuum Vent.
2
PVC Bulkhead Fitting.
3
10” Threaded Inspect Hatch (tank sizes
up to 400 gallons).
4
19” Bolted Manway (tank sizes >400 gallons).
5
Top Mounted Fill Connection with PVC
Drop Tube (option).
6
Liquid Level Indication-Molded.
7
Tank Drain/Fill Fitting, Stainless Steel
Valved.
8
Pump Supply Fittings, Stainless Steel
with Siphon Pickup.
9
Return Fitting, Stainless Steel with
Siphon Discharge.
10
Fittings (only) for tank liquid level contacts.
Material
Pigments,
Vapor Space
Fittings
Fittings,
Liquid Space
Liquid Level
Indication
High Density
Cross Linked
Polyethylene
<0.5% by weight
PVC or Stainless
Steel
Stainless Steel
Molded into side
of (translucent)
tank
Foam Concentrate Tanks
Vertical Polyethylene Storage Tanks- Dimensional Data
Nominal Vessel
Size in Gallons
Capacities
Str. Wall
Capacities
Total
Diameter
Height
Wall Thickness
(bottom third)
Weight
(less fittings)
Top
Opening
55
55
55
1 11”
3 5”
.250
35#
10”
100
100
100
1 1”
5 4”
.250
55#
10”
150
150
150
2 7”
4 6”
.250
67#
10”
200
200
200
2 7”
5 10”
.250
70#
10”
300
300
300
3 10”
4 4”
.250
90#
10”
305
305
305
2 10”
6 10”
.250
90#
10”
400
400
400
3 10”
6
.250
120#
10”
525
497
557
5 4”
3 10”
.250
185#
19”
550
550
574
4
6 7”
.250
187#
19”
800
798
822
4
9 6”
.250
200#
19”
805
805
865
5 4”
5 10”
.250
200#
19”
1000
929
988
5 4”
6 8”
.313
205#
19”
1100
1025
1178
7 1”
4 6”
.250
190#
19”
1200
1156
1215
5 4”
8
.313
260#
19”
1450
1325
1475
7 1”
6
.313
280#
19”
1500
1458
1518
5 4”
9 10”
.344
300#
19”
2000
1722
1945
8
5 11”
.313
300#
19”
2500
2286
2508
8
7 4”
.375
390#
19”
3000
2755
2977
8
8 9”
.359
470#
19”
4000
3955
4159
7 10”
12 5”
.500
720#
24”
4250
4120
4407
8 6”
11 3”
.500
795#
19”
4300
4274
4905
11 11”
6 9”
.375
1025#
24”
5000
5038
5241
7 10”
15 7”
.656
1170#
24”
5500
5154
5509
9 2”
13
.594
950#
24”
5500
5153
5508
9 2”
12 7”
.594
950#
24”
6400
6056
6424
10”
12
.500
960#
24”
6800
6835
7466
11 11”
10
.625
1610#
19”
7000
7089
7665
10
14 3”
.734
1310#
19”
8000
8317
8947
11 11”
11 8”
.703
1650#
24”
10000
10120
10750
11 11”
14
.906
2445#
24”
12000
12324
1294
11 11”
16 8”
1.047
3150#
24”
Foam Concentrate Tanks
Product:
Horizontal Polyethylene Storage Tanks
Description:
Atmospheric High Density, Cross-Linked Polyethylene
Storage Tanks are an industry standard for storing foam concentrate. They are typically used in conjunction with transportable foam trailers, pumped balanced pressure systems or
self-educting Hydro-Foam™ monitor stations. Polyethylene
is an exceptionally stable and durable material when used
to store foam concentrates. These rotationally molded,
corrosion/impact resistant horizontal/cylindrical tanks are
available in sizes ranging from 110 gallons to 2,500 gallons. Tanks are mounted on carbon steel support saddles and
secured with support bands.
Bill of Materials
Horizontal Poly
Tank
1
Pressure Vacuum Vent.
2
PVC Bulkhead Fitting.
3
10” Threaded Inspect Hatch (tank sizes <
1000 gallons).
4
19” Bolted Manway (tank sizes >1000 gallons).
5
Top Mounted Fill Connection with PVC Drop
Tube (option).
6
Liquid Level Indication-Molded.
7
Tank Drain/Fill Fitting, Stainless Steel Valved.
8
Pump Supply Fittings, Stainless Steel with
Siphon Pickup.
9
Tank Return Fitting, Stainless Steel with
Siphon Discharge.
10
Tank Return Fitting, Stainless Steel with
Siphon Discharge.
11
Fittings (only) for tank liquid level contacts.
Material
Pigments
Fittings,
Vapor Space
Fittings,
Liquid Space
Liquid Level
Indication
High Density
Cross Linked
Polyethylene
<0.5% by weight
PVC or Stainless
Steel
Stainless Steel
Molded into side of
(translucent) tank
Foam Concentrate Tanks
Horizontal Polyethylene Storage Tanks- Dimensional Data
Tank Configuration “A” (150-1000 Gallon Capacity)
Nominal
Capacity
(US Gallons)
Diameter
Length
Total
Weight
Fill
Opening
150
2 8”
4 10”
190
10”
200 x 32”
2 8”
5 8”
245
10”
200 x 38”
3 2
4 4”
245
10”
300
3 2
6 3”
305
10”
400
4
5 3”
330
10”
500
4
6 4”
350
10”
750
4 6”
7 1.5”
585
10”
1000
5 4”
7 2”
770
10” or 19”
Support Saddle “A1” - (150-500 Gallon Capacity)
Tank Size
Width
Length
150
31.5”
48”
200 x 32”
31.5”
60”
200 x 38”
37.5”
38.5”
300
37.5”
60”
400
48”
48”
500
48”
50”
Support Saddle “A2” - (750-1000 Gallon Capacity)
Tank Size
Width
Length
750
48.5”
65”
1000
57”
60”
Foam Concentrate Tanks
Horizontal Polyethylene Storage Tanks- Dimensional Data
Tank Configuration “B” (1025-2500 Gallon Capacity)
Nominal Capacity
(US Gallons)
Diameter
Length
Total Weight
Fill Opening
1025
4
12 4”
1065
19”
1625
5 4”
11 3”
1433
19”
2000
5 4”
13 1”
1550
19”
2500
5 4”
15 11”
1942
19”
Support Saddle “B”
Tank Size
Width
Length
1025
3 8.75”
9 10
1625
4 10”
9 3”
2000
4 10”
10
2500
4 10”
14 6”
Foam Systems - Around The Pump Eductors
Product:
Spectrum ATP Eductors, 2” & 3” - Grooved Type
Description:
The Spectrum Around The Pump Eductor is a fundamental, economical, yet proven way to produce foam on a fire truck. In operation a
portion of the fire water discharge is diverted to the eductor. The eductor picks up foam concentrate from the on-board atmospheric foam tank
and delivers it to the suction side of the water pump. A metering valve
such as the Spectrum Multiport Metering Valve controls the amount of
concentrate entering the system. This, along with the rate of discharge,
determines the solution flow rate; typically from 1% to 6%. All discharges in this type of system will produce foam solution. Eductors are
constructed of brass to provide years of trouble free service.
2”
3”
A
7.5”
10”
B
3.875”
5.0625”
C
2.8125”
2.6875”
D
2.625”
3.3125”
E
1.5”
2”
F
2”
3”
G
10”
15”
*Minimum straight pipe lengths
required upstream of controller
Minimum Operating Pressure = 75 psi
Maximum Operating Pressure = 225 psi
Maximum
Proportioning
Rates (gpm)
Part #
Ratio
Controller Size
Configuration
Nominal
Concentrate Flow
Drive Water
Flow @ 200 psi
3%
6%
2.0EDCT-75
2”
Grooved
75 gpm
2500
1250
85 gpm
3.0EDCT-150
3”
Grooved
150 gpm
5000
2500
150 gpm
Foam Systems - Multi Port Metering Valve
Product:
Spectrum Multi-Port Metering Valve Air Actuated
Description:
The Spectrum Multi-Port Metering Valve offers the simplicity
and reliability of fixed orifice metering coupled with the flexibility
of eight (8) air actuated ports. The valve can be custom configured
to have from 1 to 8 ports. Each port can be selected to meter solution flows from 30 gpm @ 3% up to 750 gpm @ 6%. Each orifice
can easily be removed, replaced, added or changed in the field.
Each active port features a single acting spring loaded air actuator.
This air actuator features a manual over-ride that will allow the
system to manually function in the event of air system loss. The
construction is Red Brass with Stainless Steel trim and positive
rubber valve seats.
This valve is used in conjunction with the proper Spectrum
Eductor in an Around The Pump (ATP) Foam System. Primarily
used in Airport Crash Trucks, this system offers economic reliability. As each discharge is opened an air signal is sent to the associated metering valve port. As each valve opens, more
predetermined amounts of concentrate enter the system to maintain either a 1, 3 or 6% proportioning rate.
Maximum Positive Pressure Rating is 25 psig
Part #
Description
MVM01
Valve Body & Orifice Plate
Bronze
MVM02
Air Actuated Valve
Bronze
Orifice Insert
Brass
*MVM03-(Port#)-(Diameter)
*Contact Factory for Orifice Sizing
Material
Foam Systems- Balanced Pressure Components
Product:
Spectrum Ratio Controllers, 2” & 2.5” -Threaded Type
Description:
Ratio Controllers are modified venturi foam proportioners that
accurately meter pressurized foam concentrate into the firewater stream.
These foam proportioners are used in conjunction with balanced pressure systems, such as bladder tanks and pumped proportioning skids. In
operation, firewater flows through the modified venturi, creating an area
of lower pressure, which is referred to as the “metering pressure drop”.
This metering pressure drop is directly effected by the firewater velocity
as it flows through the venturi. The (1%, 3% or 6%) concentrate-to-water
ratio is maintained over the entire flow range of each size ratio controller. However, each size ratio controller has a minimum flow rate/velocity
requirement, and these minimums must be maintained for proper ratio
controller operation.
Each Spectrum Ratio Controller consists of the following components: body; metering orifice; inlet nozzle. These components are constructed of ASTM 85-5-5-5 bronze. The inlet nozzle
is tapered and machined to a smooth finish to maximize water stream efficiency through the venturi. The foam concentrate
metering orifice is sized to the exact type and percentage of foam concentrate to be used. Both the inlet nozzle and metering
orifice are secured by a stainless steel retaining ring.
2”
2.5”
A
2.375”
2.875”
B
7”
7”
C
2.0625”
2.0625”
D
3.75”
4.125”
E
10”
13”
*Minimum straight pipe lengths
required upstream/downstream of
controller.
Ratio
Controller Size
Configuration
Nominal
ATC Flow
Nominal
AFFF Flow
Proportioning
(Fixed)
Concentrate Inlet
2”
Threaded
80-200 gpm
40-200 gpm
1%/3%/6%
1”NPT (M)
2.5”
Threaded
160-500 gpm
80-500 gpm
1%/3%/6%
1”NPT (M)
Foam Systems- Balanced Pressure Components
Product:
Spectrum Ratio Controllers, 5” Grooved
Description:
The Spectrum 5” Grooved Ratio Controller is a modified
venturi foam proportioner that accurately meters pressurized foam
concentrate into the firewater stream. This foam proportioner is
used in conjunction with balanced pressure systems, such as bladder tanks and pumped proportioning skids. In operation, water
flows through the modified venturi, creating an area of lower pressure, which is referred to as the “metering pressure drop”. This
metering pressure drop is directly effected by the firewater velocity
as it flows through the venturi. The (1%, 3% or 6%) concentrateto-water ratio is maintained over the entire flow range of the ratio
controller. However, each size ratio controller has a minimum flow
rate/velocity requirement, and these minimums must be maintained
for proper ratio controller operation.
The Spectrum Ratio Controller consists of the following components: body; metering orifice; inlet nozzle. These components are constructed of ASTM 85-5-5-5 bronze. The inlet nozzle is tapered and machined to a smooth finish to maximize
water stream efficiency through the venturi. The foam concentrate metering orifice is sized to the exact type and percentage
of foam concentrate to be used. Both the inlet nozzle and metering orifice are secured by a stainless steel retaining ring.
Ratio
Controller Size
Configuration
Nominal
ATC Flow
Nominal
AFFF Flow
Proportioning
(Fixed)
Concentrate Inlet
5”
Victaulic™ or
Gruv-Lok™
400-1800 gpm
200-1800 gpm
1%/3%/6%
2”NPT (F)
Foam Systems- Balanced Pressure Components
Product:
Spectrum Ratio Controllers, 3”,4”,6”,8”- Wafer Style
Description:
Spectrum Ratio Controllers are modified venturi foam proportioners
that accurately meter pressurized foam concentrate into the firewater stream.
These foam proportioners are used in conjunction with balanced pressure
systems, such as bladder tanks and pumped proportioning skids. In operation, firewater flows through the modified venturi, creating an area of lower
pressure, which is referred to as the “metering pressure drop”. This metering
pressure drop is directly effected by the firewater velocity as it flows through
the venturi. The (1%, 3% or 6%) concentrate-to-water ratio is maintained
over the entire flow range of each size ratio controller. However, each size
ratio controller has a minimum flow rate/velocity requirement, and these
minimums must be maintained for proper ratio controller operation.
Designed to be installed between two 150# F.F. flanges, each Spectrum
Ratio Controller consists of the following components: body; metering orifice; inlet nozzle. These components are constructed of ASTM 85-5-5-5
bronze. The inlet nozzle is tapered and machined to a smooth finish to maximize water stream efficiency through the venturi.
The foam concentrate metering orifice is sized to the exact type and percentage of foam concentrate to be used. Both the inlet
nozzle and metering orifice are secured by a stainless steel retaining ring. F.M. approved, File No. J.I.1R6A3.AF.
3”
4”
6”
8”
A
2.375”
2.5”
3.25”
3.5”
B
6.0625”
8”
12”
12”
C
2.625”
3.125”
4.125”
5.25”
D
1.25”
1.5”
2”
2.5”
E*
15”
20”
30”
40”
WEIGHT
10 lbs.
16 lbs.
32 lbs.
3 lbs.
*Minimum straight pipe length required upstream/
downstream of controller.
Ratio
Controller Size
Configuration
Nominal
ATC Flow
Nominal
AFFF Flow
Proportioning
(Fixed)
3”
Wafer, Between Flange
200-700 gpm
100-700 gpm
1%/3%/6%
4”
Wafer, Between Flange
300-1250 gpm
175-1250 gpm
1%/3%/6%
6”
Wafer, Between Flange
500-2500 gpm
350-2500 gpm
1%/3%/6%
8”
Wafer, Between Flange
950-4500 gpm
700-4500 gpm
1%/3%/6%
Foam Systems- Balanced Pressure Components
Ratio Controller Detail
Threaded - 2’ and 2.5”
Ratio
Controller Size
Configuration
Nominal
ATC Flow
Nominal
AFFF Flow
Proportioning
AFFF Flow
Concentrate Inlet
2”
Threaded
80-200 gpm
40-200 gpm
1% / 3% / 6%
1” NPT (M)
2.5”
Threaded
160-500 gpm
80-500 gpm
1% / 3% / 6%
1” NPT (M)
Grooved - 5”
Ratio
Controller Size
Configuration
Nominal
ATC Flow
Nominal
AFFF Flow
Proportioning
AFFF Flow
Concentrate Inlet
5”
Victaulic™ or
Gruv-Lok™
400-1800 gpm
200-1800 gpm
1% / 3% / 6%
2” NPT (F)
Wafer Style - 3”, 4”, 6”, 8”
Ratio
Controller Size
Configuration
Nominal
ATC Flow
Nominal
AFFF Flow
Proportioning
D
3”
Wafer, Between Flange
200-700 gpm
100-700 gpm
1% / 3% / 6%
1.25”
4”
Wafer, Between Flange
300-1250 gpm
175-1250 gpm
1% / 3% / 6%
1.5”
5”
Wafer, Between Flange
500-2500 gpm
350-2500 gpm
1% / 3% / 6%
2”
6”
Wafer, Between Flange
950-4500 gpm
700-4500 gpm
1% / 3% / 6%
2.5”
Foam Systems Components
Product:
Hydraulically Actuated Foam Concentrate Control Valve“Standard Port” Waterway
Description:
The Spectrum “Standard Port” Hydraulically Actuated Foam Concentrate Control
Valve is typically installed in the concentrate piping between the foam concentrate
storage tank and ratio controller (proportioner). When used in a balanced pressure
proportioning system, as well as most other foam concentrate applications, the valve
position is “normally closed,” preventing foam concentrate from entering into the
ratio controller. Upon system actuation, the valve will automatically open, supplying
foam concentrate to the specific (flowing) ratio controller.
Actuator Features
•
•
•
•
•
•
Operating Medium- Water
Connections-.25” (F) NPT
Seal Material- O-Rings, Buna-N
Rotational Arc, Max- 94 degrees
Max Operating Pressure- 175 psi
Position Indicator with Manual Override
Installation/Operation
The actuator is opened by introduction of system water pressure, and (therefore) requires no electrical power for operation. In most installations system water pressure is supplied to the actuator via .25” I.D. copper tubing, which is typically
connected to the trim of an automatic system valve (deluge, dry pipe, preaction).
Valve Features
• Ball valve, quarter-turn type with mounting pad.
• 600 psi WOG, cold, non-shock
• Threaded NPT (F) both ends.
• Reinforced TFE seats and stuffing box.
• Bronze body (standard) with stainless steel ball.
Std. Port
Model No.
Valve
Size
Waterway
(port)
Diameter
Minimum
Pressure
(actuator)
A
B
C
D
E
F
G
HBVS-1.0
1”
.875”
25 psi
3.625”
2.5”
4.625”
3.25”
10.125”
7”
8”
HBVS-1.25
1.25”
1”
40 psi
3.625”
2.5”
4.875”
4”
10.375”
7”
8”
HBVS-1.5
1.5”
1.25”
50 psi
3.625”
2.5”
5”
4.375”
10.625”
7”
8”
HBVS-2.0
2”
1.5”
60 psi
3.625”
2.5”
5.125”
4.6875”
10.875”
7”
8”
Foam Systems Components
Product:
Hydraulically Actuated Foam Concentrate Control Valve“Full Port” Waterway
Description:
The Spectrum “Full Port” Hydraulically Actuated Foam Concentrate Control
Valve is typically installed in the foam concentrate piping between the foam concentrate storage tank and ratio controller (proportioner). When used in a balanced pressure proportioning system, as well as most other foam concentrate applications, the
valve position is “normally closed,” preventing foam concentrate from entering into
the ratio controller. Upon system actuation, the valve will automatically open, supplying foam concentrate to the specific (flowing) ratio controller.
Actuator Features
•
•
•
•
•
•
Operating Medium- Water
Connections-.25” (F) NPT
Seal Material- O-Rings, Buna-N
Rotational Arc, Max- 94 degrees
Max Operating Pressure- 175 psi
Position Indicator with Manual Override
Valve Features
• Ball valve, quarter-turn type with mounting pad.
• 600 psi WOG, cold, non-shock
• Threaded NPT (F) both ends.
• Reinforced TFE seats and stuffing box.
• Bronze body (standard) with stainless steel ball.
Installation/Operation
The actuator is opened by introduction of system
water pressure, and (therefore) requires no electrical
power for operation. In most installations system water
pressure is supplied to the actuator via .25” I.D. copper
tubing, which is typically connected to the trim of an
automatic system valve (deluge, dry pipe, preaction).
Std. Port
Model No.
Valve
Size
Waterway
(port)
Diameter
Minimum
Pressure
(actuator)
A
B
C
D
E
F
G
HBVF-1.0
1”
1”
50 psi
3.625”
2.5”
5”
3.625”
10.375”
7”
8”
HBVF-1.25
1.25”
1.25”
60 psi
3.625”
2.5”
5.125”
4.25”
10.625”
7”
8”
HBVF-1.5
1.5”
1.5”
75 psi
3.625”
2.5”
5.375”
4.75”
10.9375”
7”
8”
HBVF-2.0
2”
2”
130 psi
3.625”
2.5”
5.625”
5.375”
11.375”
7”
8”
Foam Systems Components
Product:
Electrically Actuated Foam Concentrate Control Valve“Standard Port” Waterway
Description:
The Spectrum “Standard Port” Electrically Actuated Foam Concentrate
Control Valve is typically installed in the foam concentrate piping between the
foam concentrate storage tank and ratio controller (proportioner). When used
in a balanced pressure proportioning system, as well as most other foam concentrate applications, the valve position is “normally closed, “ preventing foam
concentrate from entering into the ratio controller. Upon system actuation, the
valve will automatically open, supplying foam concentrate to the specific (flowing) ratio controller.
Actuator Features
•
•
•
•
•
•
Unidirectional through shafted design.
Manual override, with valve position indicator.
Permanently lubricated fully closed gear train.
Water tight NEMA 4 enclosure.
Prewired terminal strip.
Maximum current requirements for open position
control - 11 amp @ 115V- 15 amp @ 24VDC.
• AC Voltages- (50 or 60 Hz), 24, 115, 220V.
• DC Voltages - 12, 24V.
Valve Features
• Ball valve, quarter-turn type with mounting pad.
• 600 psi WOG, cold, non-shock
• Threaded NPT (F) both ends.
• Reinforced TFE seats and stuffing box.
• Bronze body (standard) with stainless steel ball.
Standard Port
Model No.
Valve Size Waterway
(port)
Diameter
Standard
Voltage
A
B
C
D
EBVS-1.0
1”
.875”
24 VDC
7”
3.375”
8.75”
5”
EBVS-1.25
1.25”
1”
24 VDC
7”
4.25”
9.125”
5”
EBVS-1.5
1.5”
1.25”
24 VDC
7”
4.75”
9.375”
5”
EBVS-2.0
2”
1.5”
24 VDC
7”
5.375”
9.75”
5”
Williams’ ‘Flow Solution’
Low Pressure Drop / Wide-Range Proportioner
The Williams’ ‘Flow Solution’ Proportioner Redefines Accurate/ Wide Range Balanced Pressure Foam
Proportioning and Control!
The Williams ‘Flow Solution’ has been developed to
address the Special Hazards Fire Protection Industry’s need
for an accurate wide-flow balanced pressure foam propor
tioner which incorporates both low and constant pressure loss
with minimum water inlet pressure throughout its entire flow
range. In addition, these features are integrated into an assem
bly, which also includes precise water and foam concentrate
control. The ’Flow Solution’ proportioner is configured as
an assembly which consolidates the following system com
ponents: ratio controller; water control valve and (optional)
foam concentrate control valve with integral concentrate
check valve. Specifically suited for all closed head and
deluge foam sprinkler systems including auxiliary handline
discharges, the ‘Flow Solution’ proportioners’ revolutionary
design provides the following features:
Low, 8 PSI (nominal) Constant Pressure Loss
Throughout Entire Flow Range.
Wide Flow Range of 25gpm to 2500+gpm for Single Sprinkler Head to Total System Activation.
Low Minimum Inlet Pressure Requirement of 25 PSI Across Entire Flow Range
Configurable as Alarm Check or Water Control Valve
Fixed Proportioning of 1% or 3% with External Adjustment to Accommodate a Wide Range
of Foam Concentrate Viscosities.
‘Convertible’ 150# ANSI Flange / Grooved Water, Foam & Solution Connections
Nickel Plated Ductile Iron Body with Brass & Stainless Steel Trim
Balanced Pressure Proportioning Systems
Product:
Pump Injection Type, with Ratio Controller on Skid
Description:
The Spectrum Pump Injection Type Balanced Pressure
Proportioning Skid is a completely self-contained system which
automatically proportions foam concentrate over a wide range of
flows and pressures, without manual adjustment. The skid is installed
adjacent to an atmospheric foam concentrate storage tank, and consists of the following major components: positive displacement foam
concentrate pump; electric (or diesel) driver; pump starter/controller;
pressure balancing valve; ratio controller(s); duplex gauge; interconnecting pipe, valves, and fittings. In operation, foam liquid is drawn
from the atmospheric concentrate storage tank and pumped to the
skid-mounted ratio controller. The back-pressure type balancing
valve, installed on the tank return line regulates the amount of foam
concentrate which is returned to the storage tank, and balances the
foam concentrate pressure to match the water pressure at the ratio
controller. Water and foam pressures are monitored by a duplex
pressure gauge. Manual override of the system is accomplished through the use of a manual globe valve, installed in piping
which bypasses the diaphragm control valve. Field connections on the skid are limited to: water inlet to ratio controller; foam
solution discharge from ratio controller; electrical service to the pump motor starter/controller; foam concentrate suction and
return connections to the foam storage tank. All piping connections on the skid are 150# flanges.
Foam Storage Tank
Pump Type
Skid Concentrate
Piping
Ratio Controller
Size(s)
Standard
Proportioning
High Density
Polyethylene
Positive
Displacement
1.5”-4”
3”-8”
1% / 3%
Balanced Pressure Proportioning Systems
Product:
Pump Injection Type, with Ratio Controller on Skid
Piping Standard Piping Options Pump Standard Pump Options Standard Pump/Motor -
Schedule 40 Carbon Steel
Brass, Stainless Steel
Ductile Iron, Bronze Fitted
Bronze, Stainless Steel
Open Drip Proof 230 VAC/60/3
Model
Nominal
Solution
Flow ATC
(gpm)
Nominal
Solution
flow AFFF
(gpm)
Ratio
Controller Size
AFFF (gpm)
BPS-3L
200-600
100-600
BPS-3H
200-800
BPS-4
Pump Capacity gpm
(@200 PSI)
Bronze
Stainless Steel
1% or 3%
Limited Service, NEMA II
Enclosure
Horsepower
(pump motor)
Pipe
Size
1%
3%
1%
3%
3”
10
20
5
5
1.5”
100-800
3”
12
30
5
7.5
1.5”
300-1250
175-1250
4”
15
40
5
10
1.5”
BPS-5
400-1800
200-1800
5”
20
60
5
15
2
BPS-6L
500-2200
350-2200
6”
25
70
7.5
20
2
BPS-6H
600-2500
350-2500
6”
30
80
7.5
25
2
BPS-8L
950-2900
700-2900
8”
35
90
1.0
25
2.5”
BPS-8M
950-3800
700-3800
8”
45
120
10
30
2.5”
BPS-8H
950-4500
700-4500
8”
55
140
15
30
2.5”
Required Ordering Information:
1.
2.
3.
4.
Valve Standard Valve Options Standard Proportioning Standard Pump Controller -
Tank Capacity/Configuration
Tank Material
Type/Percentage of Foam Concentrate
System Water Pressures (static/residual)
@Ratio Controller(s)
5. Available Power Supply (voltage/cycle/phase)
6. Piping Specification
7. Valve Specification
8. Paint Specification
9. Foam System Flow Rate(s) - Minimum/Maximum
Demand
Balanced Pressure Proportioning Systems
Product:
Inline Balanced Pressure Proportioning Modules
Description:
Spectrum Inline Balanced Pressure Proportioners (ILBP’s) comprise a complete foam storage, delivery and proportioning system,
when used in conjunction with properly sized atmospheric foam
tanks, foam pumps, back-pressure control valves and concentrate
distribution piping. When supplied with foam concentrate under
adequate pressure, they are designed to accurately introduce the
foam concentrate into the water stream over a wide range of flows
and pressures by automatically responding to variations in system
demand. ILBP’s provide accurate foam concentrate introduction
at either single/local, or multiple/remote system proportioning
location(s). Each ILBP system “riser” is calculated for system
demand and then equipped with the properly sized proportioner.
InLine Balanced Pressure System Schematic
Operation:
The Inline Balanced Pressure Proportioning System utilizes a foam pump, which pressurizes the distribution piping and
ultimately supplies foam concentrate to each ILBP. Foam concentrate is stored in an atmospheric foam tank. Pumped foam
concentrate that is not delivered to the system is returned to the storage tank via a back-pressure control valve. Concentrate
discharge pressure is regulated into the system by this control valve, which can be adjusted to assure that foam concentrate is
supplied at pressures that exceed system static water pressure. Concentrate supply piping should be designed and sized so that
residual concentrate pressure exceeds (15 psi minimum) the residual water pressure at the respective inlet of each ILBP.
A pressure throttling valve is located on the concentrate inlet trim of each ILBP. The pressure throttling valve senses
foam concentrate residual pressure and automatically modulates, resulting in the balancing of the concentrate pressure with
the water pressure. A duplex gauge provides the comparative readings of concentrate and water pressure at the ILBP inlets.
Foam concentrate is then introduced to the ratio controller (proportioner) at a pressure that is equal to (balanced with) the inlet
water pressure. A modified venturi in the ratio controller body creates a temporary pressure drop in the water stream, which
then meters the proper amount of foam concentrate into the system.
Foam Systems-Balanced Pressure Components
Product:
Inline Balanced Pressure Pump Skid - Typical Schematic
Piping Standard Piping Options Pump Standard Pump Options -
Schedule 40 Carbon Steel
Brass, Stainless Steel
Ductile Iron, Bronze Fitted
Bronze, Stainless Steel
Model
Pump Capacity
(GPM)@ 200 PSI
IBPS-40
Maximum-3%
Solution Flow (gpm)
Bronze
Stainless Steel
1% / 3%
Per Schedule, NEMAII
Open Drip Proof Enclosure
230 VAC/60/3
Horse power
(pump motor)
Piping Size
(concentrate)
Type of Pump
Controller
1%
3%
40
4000
1320
10
1.5”
Limited Service
IBPS-60
60
6000
1980
15
2”
Limited Service
IBPS-80
80
8000
2640
25
2”
Limited Service
IBPS-100
100
10000
3300
25
2”
Limited Service
IBPS-120
120
12000
3960
30
2.5”
Limited Service
IBPS-140
140
14000
4620
30
2.5”
Limited Service
IBPS-150
150
15000
4950
30
3”
Limited Service
IBPS-200
200
20000
6600
50
3”
Full Service
IBPS-225
225
22000
7425
50
3”
Full Service
IBPS-250
250
25000
8250
60
3”
Full Service
IBPS-275
275
27500
9075
60
3”
Full Service
IBPS-300
300
30000
9900
75
3”
Full Service
Required Ordering Information:
1.
2.
3.
4.
Valve Standard Valve Options Standard Proportioning Standard Pump Controller Standard Pump/Motor -
Tank Capacity/Configuration
Tank Material
Type/Percentage of Foam Concentrate
System Water Pressures (static/residual)
@Ratio Controller(s)
5.
6.
7.
8.
9.
Available Power Supply (voltage/cycle/phase)
Piping Specification
Valve Specification
Paint Specification
Foam System Flow Rate(s) - Minimum/Maximum demand
Balanced Pressure Proportioning Systems
Product:
Inline Balanced Pressure Proportioning Modules
Description:
Spectrum Inline Balanced Pressure Proportioners (ILBP’s) comprise a complete foam storage, delivery and proportioning system,
when used in conjunction with properly sized atmospheric foam
tanks, foam pumps, back-pressure control valves and concentrate
distribution piping. When supplied with foam concentrate under
adequate pressure, they are designed to accurately introduce the
foam concentrate into the water stream over a wide range of flows
and pressures by automatically responding to variations in system
demand. ILBP’s provide accurate foam concentrate introduction
at either single/local, or multiple/remote system proportioning
location(s). Each ILBP system “riser” is calculated for system
demand and then equipped with the properly sized proportioner.
InLine Balanced Pressure System Schematic
Operation:
The Inline Balanced Pressure Proportioning System utilizes a foam pump, which pressurizes the distribution piping and
ultimately supplies foam concentrate to each ILBP. Foam concentrate is stored in an atmospheric foam tank. Pumped foam
concentrate that is not delivered to the system is returned to the storage tank via a back-pressure control valve. Concentrate
discharge pressure is regulated into the system by this control valve, which can be adjusted to assure that foam concentrate is
supplied at pressures that exceed system static water pressure. Concentrate supply piping should be designed and sized so that
residual concentrate pressure exceeds (15 psi minimum) the residual water pressure at the respective inlet of each ILBP.
A pressure throttling valve is located on the concentrate inlet trim of each ILBP. The pressure throttling valve senses
foam concentrate residual pressure and automatically modulates, resulting in the balancing of the concentrate pressure with
the water pressure. A duplex gauge provides the comparative readings of concentrate and water pressure at the ILBP inlets.
Foam concentrate is then introduced to the ratio controller (proportioner) at a pressure that is equal to (balanced with) the inlet
water pressure. A modified venturi in the ratio controller body creates a temporary pressure drop in the water stream, which
then meters the proper amount of foam concentrate into the system.
Foam Systems-Balanced Pressure Components
Product:
Inline Balanced Pressure Pump Skid - Typical Schematic
Piping Standard Piping Options Pump Standard Pump Options -
Schedule 40 Carbon Steel
Brass, Stainless Steel
Ductile Iron, Bronze Fitted
Bronze, Stainless Steel
Model
Pump Capacity
(GPM)@ 200 PSI
IBPS-40
Maximum-3%
Solution Flow (gpm)
Bronze
Stainless Steel
1% / 3%
Per Schedule, NEMAII
Open Drip Proof Enclosure
230 VAC/60/3
Horse power
(pump motor)
Piping Size
(concentrate)
Type of Pump
Controller
1%
3%
40
4000
1320
10
1.5”
Limited Service
IBPS-60
60
6000
1980
15
2”
Limited Service
IBPS-80
80
8000
2640
25
2”
Limited Service
IBPS-100
100
10000
3300
25
2”
Limited Service
IBPS-120
120
12000
3960
30
2.5”
Limited Service
IBPS-140
140
14000
4620
30
2.5”
Limited Service
IBPS-150
150
15000
4950
30
3”
Limited Service
IBPS-200
200
20000
6600
50
3”
Full Service
IBPS-225
225
22000
7425
50
3”
Full Service
IBPS-250
250
25000
8250
60
3”
Full Service
IBPS-275
275
27500
9075
60
3”
Full Service
IBPS-300
300
30000
9900
75
3”
Full Service
Required Ordering Information:
1.
2.
3.
4.
Valve Standard Valve Options Standard Proportioning Standard Pump Controller Standard Pump/Motor -
Tank Capacity/Configuration
Tank Material
Type/Percentage of Foam Concentrate
System Water Pressures (static/residual)
@Ratio Controller(s)
5.
6.
7.
8.
9.
Available Power Supply (voltage/cycle/phase)
Piping Specification
Valve Specification
Paint Specification
Foam System Flow Rate(s) - Minimum/Maximum demand
Foam Systems-Balanced Pressure Components
Product:
Spectrum Back Pressure Control Valve
Description:
The Spectrum #108-2WF Back Pressure Control Valve is typically
installed on the foam concentrate pump-to-tank return line of a pumped balanced pressure proportioning system. The pilot operated, diaphragm actuated
150# globe valve is designed to control foam concentrate pressure at the inlet
and is set to maintain a regulated pressure in the concentrate distribution piping which supplies one or more (remote or local) Inline Balanced Pressure
Proportioning Modules (ILBP’s). The valve’s diaphragm is nylon fabricated
(bonded with synthetic rubber), and forms a sealed chamber in the upper portion of the valve, separating operating pressure from line pressure. The valve
automatically opens to relieve any pressure above its (adjustable) set point
and foam concentrate that is not delivered to the ILBP(s) is returned to the
concentrate storage tank. Standard inlet/discharge - 150# FF flange.
1
Basic Control Valve
2
Pressure Relief Pilot
3
Ejector, Fixed Restriction
4
Flow Control Valve
5
Sense Line Drain Orifice
6
Ball Valve- Sense Line Flush
Size
Ductile Iron/
Epoxy Coated
Bronze
Stainless Steel
A
B
C
1.5”
108-2WF-1.5 DI
108-2WF-1.5 B
108-2WF-1.5 SS
8.5”
2.5”
12.375”
2”
108-2WF-2.0 DI
108-2WF-2.0 B
108-2WF-2.0 SS
9.375”
3”
12.375”
2.5”
108-2WF-2.5 DI
108-2WF-2.5 B
108-2WF-2.5 SS
10.5”
3.5”
14.375”
3”
108-2WF-3.0 DI
108-2WF-3.0 B
108-2WF-3.0 SS
10.5”
3.75”
14.625”
4”
108-2WF-4.0 DI
108-2WF-4.0 B
108-2WF-4.0 SS
13.5”
4.5”
16.375”

Similar documents