height safety - NZ Safety Online Catalogue

Transcription

To reduce falls
from height in the
workplace, hazard
identification and
training are essential.
HEIGHT SAFETY
In New Zealand,
more than 50%
of reported falls
are from less
than 3 metres.*
*Statistics supplied by WorkSafe NZ.
Don’t gamble with safety.
29
HEIGHT SAFETY
LEGAL REQUIREMENTS AND EMPLOYER RESPONSIBILITY
Eliminate
The Health and Safety in Employment
Act 1992 requires that if there is a
potential for a fall from any height,
reasonable and practical steps must be
taken to prevent harm from resulting.
A mistaken belief exists that no controls
are needed where risk of fall is less than
3 metres. 50% of reported falls in the
workplace in New Zealand are from less
than 3 metres.
HEIGHT SAFETY
AS/NZS Standards
AS/NZS 1891.4:2009 - INDUSTRIAL
FALL-ARREST SYSTEMS AND DEVICES SELECTION, USE AND MAINTENANCE
The Standard specifies requirements
and sets out recommendations for the
selection, safe use and maintenance of
industrial fall-arrest systems and devices
based on the use of safety harnesses,
horizontal life lines and rails, fall-arrest
devices, and associated lanyards,
connectors, anchorages and fittings.
HIERARCHY OF CONTROLS
The best method of hazard control is to
eliminate the potential for a fall.
• SAFER DESIGN - Location of plant
equipment, use of walkways &
handrails, use of parapets, etc.
develop a system and work plan for
managing hazards.
We recommend you refer to the
hierarchy of controls outlined in HSE
Act (1992) and AS/NZS 1891.4:2009.
• ALTERNATIVE CONSTRUCTION
METHODS - Fabricating structures on
the ground and lifting into position.
• USE OF TOOLS & EQUIPMENT - Use of
long-handled tools eliminating the
need to work from a ladder
Hazards need to be identified,
assessed, evaluated, then eliminated
or controlled. AS/NZS ISO 31000:2009
gives guidance on risk management.
Isolate
Risk assessment and control measures
help identify:
• S caffolding or elevated work
platforms
• What hazards are involved with the
task and who could be affected by
the dangers
• Edge Protection
Height Safety Hazard
Management Planning
• What instructions (including rescue)
need to be written
Too many falls from height are caused
by a failure to plan and organise work
properly. Prior to working at height
• What training is necessary
Can the hazard of working at height be
isolated?
• Mechanical access
• What equipment needs to be used
The best type and combination of
equipment that should be used can
be very specific to the actual height
safety situation.
A B C D OF HEIGHT SAFETY EQUIPMENT
Minimise
Involves the use of fall arrest equipment
and allows a worker to be protected
while positioned at a work location
where there is a risk of fall occurring.
Regardless of whether a restraint, positioning or arrest system is employed, the basic
A,B,C,D components of a height safety system remain consistent and need to be included.
THE MOST COMMON SYSTEMS USED
INCLUDE:
A
• Total restraint system
ANCHORAGE POINT
B
BODY HARNESS
• Work positioning system
• Fall arrest system
C
30
CONNECTOR
D
DESCENT & RESCUE PROVISION
www.nzsafety.co.nz | 0800 NZSAFETY (0800 697 233)
HEIGHT SAFETY
AS/NZS STANDARDS COMPLIANT EQUIPMENT & TRAINING
Based on the
Health and Safety in
Employment Act,
WorkSafe NZ
Best Practice
Guidelines and
NZQA Unit Standard
course content, it is
recommended that
only AS/NZS standards compliant
height safety equipment should be
used in New Zealand workplaces.
Height Safety training programmes
should cover the following:
• Requirements of standards and
legislation
• Identification of relative hazards
• Application of the hierarchy of control
and other measures to minimise and
control risk
• Rescue plans and procedures
WE OFFER
PRACTICAL &
CUSTOMISED
HEIGHT SAFETY
COURSES.
• The use, fit, inspection and
maintenance of fall protection
equipment
HEIGHT SAFETY
See pages 10-14 for
more information.
Training Requirements
If you are required to perform any tasks
at height, you must be competently
trained as per AS/NZS 1891.4.
DIFFERENCES BETWEEN AS/NZS AND EN/ISO REQUIREMENTS
Criteria
AS/NZS
EN/ISO
Comments
Webbing
Polyester webbing tested and
No UV test requirements.
AS/NZS web products are provided with a 10
year manufacturer's warranty.
approved for UV light degradation
and manufactured for 10 year life
span of product required.
Validation Testing
Harness Capacity
1 in every 500 units manufactured
No requirement.
Variations in materials between batches are
must be tested for ongoing
not necessarily picked up without certification
compliance with the Standard.
testing. The AS/NZS testing regime reduces risk.
Though a weight is not stipulated
100kg only.
Consider the combined weight of worker +
clothing + tools
in the Standard, a 100kg test weight
is used resulting in a minimum
136kg requirement.
Labelling
States manufacture and certification
May simply state
An AS/NZS "certified" product means that all
to the testing requirements of
"conforms to"
requirements for raw materials, total assembly
AS/NZS under the supervision of
or "complies with" the
testing, validation testing, factory & quality
3rd party certifying body e.g.
requirements of AS/NZS.
audits are observed resulting in the issuing of
SAI Global, Benchmark.
factory licence and/or identification numbers.
EN or ISO certified products may claim “conformance to” AS/NZS 1891.1 however unless they carry an
AS/NZS certification label they have not been tested to and are not compliant to the AS/NZS 1891.1 Standard
31
HEIGHT SAFETY
EQUIPMENT MAINTENANCE
When should
equipment be removed
from service?
Inspection and
maintenance
requirements
• S ix monthly service and/or periodical
inspection is due
All fall protection equipment must
be inspected prior to and after each
use by the user and periodically by a
competent height safety equipment
inspector as defined by Australian &
New Zealand Standard AS/NZS 1891.4.
• It has been involved in a fall
• Labels have been removed,
are missing or illegible
• Excessive abrasive wear (furry or
frayed surfaces) has occurred
Height safety
equipment
requires
regular
inspections
& servicing
• B roken fibres, tears, cuts, snags and
splinters are present
• Weld burns are present
• Deterioration or stretching has
occurred
• Loss of resilience, discolouration or
visible damage is experienced
HEIGHT SAFETY
• Parts and mechanisms are not
moving freely or are corroded
• There is reduction in cross-section of
rope area or webbing
• There is excessive contamination
not removed by approved cleaning
methods
• It is more than 10 years old for
AS/NZS certified products
Australian and New Zealand Standards
also require that all fall arrest devices
such as SRLs be subjected to a full
inspection and service by factory
accredited service centres every
12 months in the absence of any
instructions/recommendations from
the manufacturer.
They must also be re-certified by the
manufacturer or their accredited
service agent after they have been
used to arrest a fall.
FOR MORE INFORMATION
CONTACT NZ SAFETY TODAY
As per AS/NZS 1891.4
KNOWLEDGE IS THE BEST PROTECTION
Our NZQA qualified trainers provide customised courses at your workplace
providing relevant interactive training in real life environments.
Call us today for an on-site training evaluation, and discover why New Zealand’s
leading employers entrust the training of their people to NZ Safety.
32
HEIGHT SAFETY
CORRECT FITTING IS ESSENTIAL
2. SUB PELVIC STRAP
The positioning of the
sub-pelvic strap is critical.
Adjust the shoulder straps to
ensure the sub-pelvic strap
is positioned directly below
the buttocks.
4. CHEST STRAPS
Position chest
strap across the
middle of the chest,
approximately
3 finger widths
above the base of
the sternum. Shoulder
straps should be
vertical, not pulled
into centre of body.
3. LEG STRAPS
Adjust the leg straps
so that a flat hand
(not a fist) can be
placed between the
leg and the leg strap
5. FINAL ADJUSTMENTS
The harness should be
comfortable without
undue pressure on the
shoulders, thighs or
pelvis. You should still
have your full range
of motion with the
harness fitted.
HEIGHT SAFETY
1. GETTING STARTED
Hold harness by back
D-ring, ensure all buckles
are undone and ensure
there are no tangles in
the webbing.
HARNESS SIZING CHART
150
145
140
Extra Large
135 Waist in Centimetres
130
125
120
115
Large
110
105
100
95
90
Medium
85
80
75
70
65
60
Small
55
50
40
45
50
55
60
65
70
75
80
85
90
95
100
105
110
115
120
125
130
135
Weight in Kilograms
Whether you wear a harness for 4 hours a day or 14 hours a day, proper fit is essential. The harness needs to
feel good and fit right for optimum comfort, safety and productivity.
Capital Safety manufactures harnesses that are designed to fit most body sizes or shapes (S-XL) under the
brands of DBI-SALA, PROTECTA and FIRST.
33
HARNESSES
EXOFIT HARNESSES
Get into the best!
Comfort
Function
Durability
HEIGHT SAFETY
REPEL™ TECHNOLOGY
WEBBING
Water, mould and dirt
repellent - up to 5 times
more abrasion resistance
TECH-LITE™
ALUMINIUM D-RINGS
Patented spring loaded
stand up dorsal D-ring for
easy, safe connection
EXOFIT NEX™
CONFINED SPACE HARNESS
• Fall-arrest rated front D-ring
• Confined space retrieval loops
• Certified to AS/NZS 1891.1:2007
• Wide padded waist belt with large side
D-rings for work positioning
Applications: Rigging, construction,
confined space access and
general work at height.
Sizes: S, M, L, XL
Applications: Confined space
access, work positioning
and construction.
Sizes: S, M, L, XL
CODE 405962 603X2018
CODE 405961 623X2018
EXOFIT NEX™ RIGGERS HARNESS
DUO-LOK™ QUICK
CONNECT BUCKLES
One-handed operation with
memory-fit web-lock for fast,
slip free connection
REVOLVER™ VERTICAL
TORSO ADJUSTER
Fast, simple adjustment,
eliminating loose ends and
locks into place preventing
slippage
INTEGRATED
TRAUMA STRAPS
Provides relief after a fall to
minimise suspension trauma
COVERED LABELS
AND I-SAFE™
Built-in RFID tag makes
accessing and recording
inspections fast and easy
BONUS HARD WEARING
HARNESS STORAGE
BACKPACK
EXOFIT NEX™ LINESMAN AND
TOWER WORKER HARNESSES
• Webbing dorsal connection with
300mm extension
• Fall arrest rated front belay loops
• Confined space attachment loops
• Padded waistbelt with D-rings for
work positioning
• Additional side O-rings for pole work
• Padded work positioning buttock seat
Applications: Electrical utilities, live-line
and work positioning.
Sizes: S, M, L, XL
CODE 408434 663x4019 Linesman
410665 663x4018 Tower Worker
34
EXOFIT NEX™
CROSSOVER HARNESS
• Easy donning crossover design
• Fall arrest rated front D-ring
• Ideal harness for women workers
Applications: Rigging, construction and
general work at height
Sizes: S, M, L, XL
CODE 410664 613x2016
HARNESSES
DELTA HARNESS RANGE
Durability
when it counts!
• Waist belt with large side D-rings for positioning
Applications: Rigging, construction,
confined space access and
Sizes: S, M, L, XL
Applications: Confined space
access, work positioning
and construction.
Sizes: S, M, L, XL
CODE 407784 803X0018
CODE 407785 823X0018
REPEL™
TECHNOLOGY WEBBING
Water repellent to reduce
the attraction of mould and
dirt - up to 5 times more
abrasion resistance
STAND-UP
DORSAL D-RING
Unique spring loaded back
D-ring ensures fast easy to
reach connections
QUICK CONNECT
BUCKLES
HEIGHT SAFETY
DELTA™ ALL-PURPOSE HARNESS
DELTA™ RIGGERS HARNESS
Lightweight construction
with intuitive operation
and memory-fit for easy
one-handed operation
LABEL PACK
Laminated PVC labels
resistant to abrasion, UV,
ambient heat, water and a
wide range of chemicals
I-SAFE™ INTELLIGENT
SAFETY SYSTEM
DELTA™ LINE WORKER HARNESS
DELTA™ TOWER WORKERS
HARNESS
• Fall-arrest rated belay loops
• Padded waist belt with side D-rings for
work positioning
• Padded work positioning buttock seat with
additional lower side D-rings for pole work
• Webbing dorsal connection with
300mm extension
• Fall-arrest rated front belay loops
• Wide padded waist belt with side angled
D-rings for work positioning
• Additional lower side O-rings for pole work
• Padded work positioning buttock seat
Applications: Tower and line work,
work positioning and rescue.
Sizes: S, M, L, XL
Applications: Electrical utilities,
elevated work platforms, live-line
Sizes: S, M, L, XL
CODE 407787 853X0018
CODE 407770 390X4147A
Built-in RFID tag makes
accessing and recording
inspections, inventory
and user information fast
and easy
DELTA HARNESSES SUPPLIED
WITH STORAGE BAG
35
HARNESSES
AIRCORE™
HARNESS RANGE
• Reduces padding
contact
• Reduces weight
• Increases worker
comfort
AIRCORE™
CONSTRUCTION HARNESS
• Quick-connect buckles
• Aluminium stand up rear D-ring
• DuraClean coating repels water, oil and
dirt, increasing durability
• Confined space webbing loops
HEIGHT SAFETY
BREATHABLE
AIRCORE™ RIGGER’S HARNESS
• Q uick-connect buckles
• Work positioning side D-rings
Applications: Construction, maintenance,
scaffolding and warehousing.
Sizes: S, M/L, XL/XXL.
Applications: Construction, maintenance,
scaffolding, ladder safety systems, confined
space rescue, elevated work platforms
CODE 410456
CODE 410457
AIRCORE™
TOWER WORKERS HARNESS
AIRCORE™ TOWER WORKERS
HARNESS WITH SOFT LOOPS
• B uilt-in buttock pad increases comfort for
work positioning
• B uilt-in buttock pad increases comfort for
work positioning
Applications: Tower work, ladder work,
pole top and line work.
Applications: Tower work, ladder work, pole
top and line work.
CODE 410456
CODE 410459
AIRFLOW
STRETCHABLE
DURAFLEX™
WEBBING
The Aircore™ is a lightweight,
full-body harness designed with
breathable, open-core padding
technology that provides optimal
air flow, while reducing heat and
moisture entrapment - keeping you
cooler, drier and more comfortable.
DuraFlex™ webbing flexes with your
movement to provide optimum
comfort and reduced fatigue.
36
HARNESSES
DURAFLEX™
HARNESS RANGE
MAXIMUM
• Comfort
• Compliance
• Safety
• Frontal and rear fall arrest attachment
points, rear and extended dorsal dee
• Waist belt for greater support and stability
Applications: Rigging, confined space
access, construction, work positioning
and general work at height.
CODE 403794
DURAFLEX™
MAINTENANCE HARNESS
• Front fall-arrest attachment point, rear and
extended dorsal D-rings
• Confined space loops
• Easy to fit with fully adjustable chest,
shoulder and leg straps
HEIGHT SAFETY
DURAFLEX™ RIGGER’S HARNESS
Applications: Scaffolding, construction
and confined space access.
CODE 403798
Miller® DuraFlex™
webbing harnesses
conform to the
shape of the worker,
stretching with
every movement
DURAFLEX™
DURAFLEX™
GLOVE & BARRIER HARNESS
• Frontal belay loops for fall arrest
• 500mm extended dorsal with soft-eye-dee
• Fully adjustable leg, chest and shoulder straps
The flexibility of DuraFlex™ webbing
offers unsurpassed comfort, greater
mobility and wider user acceptance
resulting in increased compliance
and safety.
• 300mm extension off rear fall arrest
soft-eye-dee
• Frontal fall arrest attachment loops
• Confined space shoulder loops
• Label pack with lanyard parking ring
stores harness documents
• Adjustable shoulder and leg straps
• Certified to AS/NZS 1891.1 2007
Applications: Live wire applications,
EWP and confined space.
Applications: General work at height,
construction, confined space access
and rescue.
CODE 501001
CODE 819816
37
HARNESSES
Harnesses
and lanyards
should be
inspected and
logged every
six months*
Nationwide on-site inspection service
and factory accredited workshop.
• height safety
• confined space access
• gas detection
HEIGHT SAFETY
For more information contact
NZ Safety today
*As per AS/NZS 1891.4
• Heavy duty and lightweight fluorescent
orange polyester webbing
• Front fall-arrest, rear dorsal and extended
dorsal D-rings
• Work positioning D-rings
• Back and buttock pad both offering
comfort, support and stability
construction, confined space access
and rescue.
Applications: Pole top, line workers, tower
workers and ladder work.
One size (M).
CODE 817562
CODE 850050
CONSTRUCTION HARNESS
• Front and rear fall-arrest rated D-rings
• Secure label pack
• High-visibility fluorescent green webbing
• Wide padded waist-belt with side D-rings
• Integrated shoulder pads for comfort
CODE 4
03203 Small
403204 Medium
403205 Large
38
• Rear fall-arrest D-ring and 300mm extension
with soft-eye-dee
• Front fall-arrest rated belay loops
• Quick-release buckles
• Padded leg straps for additional comfort
INDUSTRIAL HARNESS
Applications: Rigging,construction,
elevated work platforms, ladder access
LINE WORKER HARNESS ELITE 2
• Shoulder D-rings for spreader bar attachment
• Secure label pack
Applications: Construction, work positioning
Applications: Confined space access,
rigging, construction and general work
at height.
CODE 4
03209 Small
403210 Medium
403211 Large
CODE 4
03206 Small
403207 Medium
403208 Large
HARNESSES
WORKING IN RESTRAINT
The best
option when
working at height
because you are
restricted from a fall
Working in restraint is when your fall
protection equipment is used to
prevent access to an edge, or to
prevent you from reaching a position
where there is a risk of free fall.
• Over the head cross-over design
• Hybrid polyester and DuraFlex™ webbing
provides optimum worker comfort
• Large front and rear fall-arrest D-rings
• Convenient, economical harness
• Quick release leg buckles for fast and
simple donning
• Front & rear D-rings
Applications: Roofing, construction
Applications: Construction & maintenance,
scaffolding and warehousing.
One size M/L.
CODE 896014
CODE 409379
WORKING POSITIONING
When
you are
supported
by the fall protection
equipment in such
a way that a fall is
partially restrained
A common example is when
working on a ladder with a pole
strap connected to the side D-rings
on a harness.
WORKING IN FALL-ARREST
HEIGHT SAFETY
CONSTRUCTION PLUS HARNESS
ROOF WORKER HARNESS
The least
preferred
method
for working
at height
FIRST™ COMPLIANCE HARNESS
FIRST™ CHERRY PICKERS HARNESS
• Rear fall-arrest rated D-ring
• Front fall-arrest attachment loops
• Fully adjustable
• One size only
• Integral adjustable lanyard with shock
absorber (0.75m - 2.0m)
• Front fall-arrest attachment loops
• Fully adjustable
• One size only
maintenance and construction.
Applications: Cherry pickers and
elevated work platforms (EWPs).
CODE 500577
CODE 500576
Working in fall-arrest means that
there is a likelihood of a free fall
greater than 600mm. This should only
be performed by trained personnel.
When working in fall-arrest it is
imperative that a rescue plan is in
place to retrieve anyone who falls.
Free-fall distance must never
exceed two metres.
39
SPECIALITY
DO YOU HAVE A
SPECIALIST APPLICATION?
PRO™ WELDING HARNESS
AND LANYARDS
ExoFit™ NEX
Flotation
Harness
Ideal for the professional
requiring both fall and
buoyancy protection in
open or closed waters.
Available in: S, M, L & XL
HEIGHT SAFETY
ExoFit™ NEX
Derrickmans
Harness
Ideal for professional oil
industry personnel when
working on the derrick/
monkey board.
Available in: S, M, L & XL
Contact NZ Safety for a free
on-site assessment
TRAILER DEMONSTRATION
Specifically designed for welding applications
to provide heat and char resistance.
• Heat resistant & flame retardant webbing with
high durability and resistance to abrasion
• Lanyard features a heat & char resistant
shock pack cover that slips over shock pack
• Harness and lanyard Kevlar webbing is
heat resistant up to 371°C
• Front and rear fall arrest rated D-ring
• Fully adjustable harness with pass-through
buckles and torso adjusters
• Lightweight design to improve comfort
Applications: Welding, hot work and general
work at height. Sizes: S, M, L.
CODE 4
11343 Welding Harness
411344 Twin tail welding lanyard with scaff hooks
411345 Single tail welding lanyard with scaff hook
411346 Single tail welding lanyard with snap hook
Capital Safety site inspection
and reporting service
Bringing height safety
education to you
• Educational focus
• Live drop tests
• Hands on access to the
latest products
Contact NZ Safety to arrange
a free on-site height safety
trailer demonstration
Capital Safety’s trained technicians
provide a comprehensive
investigative report outlining
height related operational
hazards at your workplace.
Receive a customised
recommended solution to
improve worker safety,
increase productivity and
minimise equipment costs.
CODE 4
10671 - Half Day Site Inspection
410672 - Full Day Site Inspection
40
HEIGHT SAFETY KITS
ACCESSORY
HARNESS STORAGE BAG
Contents not included.
CODE 401211
ROOFERS KIT
CONSTRUCTION KIT
Applications: Roofing, construction,
maintenance and
demolition.
Ideal for elevated platforms and scaffolding
or building edges , suits most construction
height situations.
Kit includes:
• Fall arrest harness with front and rear D-rings
(403204)
• 1.5m anchor strap (405091)
• Karabiner (401325)
• Adjustable scaffold lanyard (404296)
• Backpack kit bag
CODE 405087
CODE 409800
ACCESSORY
SUSPENSION
TRAUMA STRAPS
While the suspended worker is awaiting
rescue they can stand up in their
harness to relieve the negative effects
of suspension trauma. Fits all styles
of harnesses.
CODE 401045
WE DON’T JUST
SELL SAFETY
EQUIPMENT,
WE MAKE SURE
YOU KNOW
HOW TO USE IT.
HEIGHT SAFETY
Kit includes:
• Fall arrest harness with front and
rear D-rings (403204)
• 1.5m anchor strap (405091)
• Karabiner (401325)
• 11.5mm kernmantle rope lifeline - 15m
(405088)
• Backpack kit bag
Our practical training
courses include:
• Safe Work at Heights
• Height Safety
Equipment
• Fall Arrest Systems
• Climb and Work
Off Structures
• Industrial Abseiling
• Rescue
FIRST™ ROOFERS KIT
“Compliance in a Can”
Kit includes:
• Fall-arrest harness (500577)
• 15m rope lifeline with 1.0m integral shock
absorbing lanyard (405088)
• 1.5m round anchor strap (405091)
• Packed in a rugged reusable carry bucket
Applications: Roofing, construction,
maintenance and demolition.
CODE 401720
• Certificate in Height
Safety and Rescue
ROOFERS KIT ROPE LIFELINES
• 11.5mm kernmantle rope lifeline
• Karabiner on each end
• Manual rope adjuster
• Integral 1.0m shock-absorbing lanyard
CODE 4
05088 15m
405089 20m
405090 30m
41
LANYARDS
FORCE2™
Revolutionary
lanyard
technology
• Smallest shock
absorber in the world
66%smaller* &
40% lighter*
• Lightest & strongest
connector
combinations on
the market
FORCE2™ WEBBING LANYARD
• REPEL™ Technology
webbing
• Hi Vis yellow webbing
• Steel hardware
• Certified to AS/NZS 1891:1:2007
standard
• Alloy hardware for less weight
standard
• Protected labels
CODE 4
09694 2m adjustable Single tail with
double action snap hooks
CODE 4
09696 2m elasticated Single tail with
double action scaff hooks
HEIGHT SAFETY
• Rated to 160kg
for all sizes
of workers
*Compared to
previous FORCE2™
models
FALL DISTANCE MINIMISED
Ensure you are safe by calculating
your fall clearance using the diagram.
Remember working in restraint and
preventing a fall is always best.
For example, a 2.0m shock absorbing
lanyard and a 2.0m free-fall requires
a fall clearance of 5.70m from the
anchorage point.
For more information refer to
AS/NZS 1891.4
FORCE2™ WRAPBAX™
TIE-BACK LANYARDS
standard
• Heavy duty webbing provides 5 x more
abrasive resistance for tying off on harsh
surfaces
standard
CODE 4
09695 2m elasticated Twin tail with
double action scaff hooks
CODE 4
09697 2m Single tail with double
action snap hooks
409698 2m Twin tail with double
action snap hooks
FORCE2™ ROPE LANYARD
FORCE2™ ROPE LANYARD
• Hi Vis yellow kernmantle rope
standard
• Hi Vis yellow kernmantle rope
standard
CODE 4
09699 2m Single tail rope adjustable with karabiner
CODE 4
09703 2m Twin tail with double action scaff hooks
After Fall Anchorage Calculation
42
Length of
Lanyard
(anchored with
no slack)
2.00m
Deceleration
distance
(for energy
asborber)
Max
0.90m
Height of
worker
1.80m
Safety factor
1.00m
Total Distance from Anchorage
For a 2 metre energy absorbing Lanyard
(see AS/NZS 1891.4)
5.70m
LANYARDS
MILLER ® SHARP EDGE
RANGE
Don’t let sharp edges
bring you down
ADJUSTABLE LANYARD
CODE 402993 2.0m adjustable lanyard
404296 2.0m adjustable scaffold lanyard
FIXED LENGTH LANYARDS
• 19mm snap hook both ends
• 16kN gate strength
• Rated to 160kg
CODE 4
00063 2.0m (Prosafe - Green)
400677 1.5m (Protecta - Red)
400676 1.0m (Protecta
- Red)
EXTRA
PROTECTION
AGAINST
SHARP EDGES
MANYARD LANYARD
TWIN SCAFFOLD LANYARD
• Ideal for scaffolding or access on structures
• 56mm scaffold hooks on the tail ends
• 19mm snap hook on the shock pack end
• Rated to 160kg
• Specially woven shock absorbing inner
core which smoothly expands to reduce
fall arrest forces
• No energy absorber pack making it more
comfortable to use
• 19mm snap hooks each end
• Certified to AS/NZS 1891.1 2007
CODE 401064 2.0m elastic
CODE 402068 2.0m
SHARP EDGE ADJUSTABLE LANYARD
• 2.0m adjustable lanyard
• Robust 12mm sharp edge kernmantle rope
• Rope adjuster moves along the rope to
adjust length
• Includes compact energy absorber
and 19mm snap hooks on each end
CODE 405853
SHARP EDGE
FIXED LENGTH LANYARD
• 2.0m lanyard
• Includes compact energy absorber
and 19mm snap hooks on each end
CODE 405852
Miller ® Sharp Edge products are
designed to protect workers at
height should a fall take place over
a sharp edge. Our range includes
sharp edge lanyards, anchorage
lines and fall arrestors, and feature
quality hardware.
HEIGHT SAFETY
• Adjusts from 0.75m–2.0m
• 19mm snap hook both ends with
16kN gate strength
• Rated to 160kg
SHARP EDGE ANCHORAGE LINE
Ideal for any situation that requires an
adjustable anchorage line such as roof access.
• Type 1 fall arrestor moves along the rope,
locks in the event of a fall
• Includes karabiner and snap hook
CODE 4
07294 15m
407295 30m
43
POLE STRAPS
INSPECTION & SERVICING
Summary of
inspection frequency
requirements
AS/NZS 1891.4:2009
INSPECTION BY HEIGHT SAFETY
OPERATOR BEFORE AND AFTER USE.
All personal height safety equipment.
SIX MONTHLY INSPECTION BY A
HEIGHT SAFETY EQUIPMENT INSPECTOR
OR AS RECOMMENDED BY THE
MANUFACTURER.
• Harnesses, lanyards, fall-arrest
devices (external inspection only),
ropes, slings and associated
personal equipment
POLE STRAP
POLE STRAPS
• 2.5m length with easy and efficient
adjustment system
• Integral wear-sleeve provides abrasion
resistance and extends product life
• 19mm snap hook both ends with 16kN
gate strength
• Certified to
AS/NZS1891.1:2007
• Lightweight, alloy double action snap
hooks for easy connection
• Easy and efficient adjustment system that
can be adjusted whilst working
• Heavy duty integral wear sleeve
provides abrasion resistance
and extends product life
CODE 400511 2.5m
CODE 4
04126 2.0m
401209 2.5m
HEIGHT SAFETY
12 MONTHLY INSPECTION BY A HEIGHT
SAFETY EQUIPMENT INSPECTOR.
• Anchorages - drilled in type or fixed
to timber frames - other types can
be up to five yearly if approved by
the manufacturer
• Horizontal and vertical lifelines –
steel rope or rail
• Fall-arrest devices – full service
POLE STRAPS
Ideal for work positioning, restraint and
assisted climbing.
• 16kN gate strength on all hooks
• Easy and efficient adjustment system that
can be adjusted whilst working
• Heavy duty integral wear sleeve
provides abrasion resistance and
extends product life
CODE 4
10650 2.5m with snap hook and karabiner
410651 2.0m with snap hook and karabiner
410652 2.5m with triple action karabiner
ARBORIST POLE STRAP
Designed for positioning, restraint and
climbing when using a chainsaw
• Ideal for arborists and tree pruning
• Wire core rope prevents
accidental cutting of pole strap
• Rope adjuster provides quick
and easy adjustment
CODE 4
07176 1.2m
407177 1.5m
YOU NEED TO
BE PROPERLY
TRAINED TO
WORK SAFELY
AT HEIGHT.
POLE STRAPS
Used in applications such as line and pole
top work.
• Fully adjustable and available in
various lengths
• Two 19mm snap hooks with easy adjuster
• Includes wear-protection sleeve
See page 10-14 for
more information.
CODE 8
50051 1.8m
500801 2.4m
896326 2.7m
44
SELF RETRACTING LIFELINES
FLEXIGUARD
ACCESS SYSTEMS
DBI-SALA’s
FlexiGuard™ height
access systems
NANO-LOK™ SELF RETRACTING LIFELINE
The smallest and lightest self retracting lifeline (SRL) on the market today - Nano-Lok™ is
ergonomically designed for ease-of-use and is ideal for direct connection to most harnesses it’s virtually unnoticeable to the user!
• Sharp edge compliant (orange one pictured)
• 1.8m working length
• Quick-connect anchorage connector (single or twin leg) for direct connection to the harness
without the requirement for a separate Karabiner
•C
ab-mount anchorage connector for direct attachment to the cab of order pickers
• Karabiner connection for direct connection to harness D-ring
Provide mobile overhead
anchorage points that can
be moved from application to
application. Ideal for situations
where an overhead structure is
unreachable or does not exist.
These systems are robustly built
and are typically rated for at least
two users. Fixed or adjustable in
height, they provide an active fall
protection solution for a wide range
of applications.
CODE 4
07987 Standard hook
407988 Scaffold hook
407989 Twin leg
407990 Cab mount
410670 Sharp edge with scaffold hook (2.4m working length)
Other connection configurations available upon request.
PORTABLE TANKER ACCESS LADDER
SYSTEM-WORK POSITIONING
A-FRAME RAIL
FALL ARREST SYSTEM
BOXED-FRAME RAIL
FALL ARREST SYSTEM
COUNTERWEIGHT RAIL
FALL ARREST SYSTEM
LADDER
FALL ARREST SYSTEM
PORTABLE TANKER ACCESS
LADDER SYSTEM-FALL ARREST
HEIGHT SAFETY
Applications: Warehousing, construction and general work at height.
Safety from
the ground up!
TURBOLITE™ SELF RETRACTING LIFELINES
The TurboLite™ is a small and lightweight 2.0m webbing self retracting lifeline designed as a cost
effective alternative to traditional lanyards.
• Includes twistlock karabiner at top and either snap or scaffold hook
• Optional Twin Turbo bracket connects two TurboLites to a fall-arrest D-ring for continuous tie-off
Applications: Warehousing, construction and general work at height.
CODE 4
04837 19mm snap hook
404838 56mm scaffold hook
405975 Twin Turbo bracket
45
INCREASE MOBILITY
HEIGHT SAFETY
SRLs offer greater
mobility than
conventional lanyards
and automatically
minimise fall distances
REPLACE YOUR LANYARD AND IMPROVE
PRODUCTIVITY AND SAFETY TODAY
FALCON™
The Miller® Falcon™ has a lightweight, high
impact-resistant nylon housing to withstand
toughest applications.
• Corrosion resistant stainless steel and
aluminium internal components
• Swivel top and bottom attachments
• Internal shock absorption
• Factory recertification only required every
five years
46
REBEL™
SELF RETRACTING LIFELINE
BLACK RHINO™
SELF RETRACTING LIFELINE
• 3.3m working length
• Compact and lightweight, only 1.3kg
• Integral webbing energy absorber
• Snap hook and karabiner included
Compact and lightweight, only 1.9kg.
• 2.7m stainless steel cable
• Internal shock absorber
• Impact-resistant aluminium outer casing
• Karabiner on top and swivel snap hook
Applications: Warehousing,
construction and general
work at height.
CODE 400813 3.3m
Applications: Construction, hot work and
CODE 402067
REBEL™ SELF RETRACTING LIFELINE
The Protecta® Rebel™ sets performance
standards beyond compliance, while
providing substantial value for money.
• Galvanised cable lifeline
• Swiveling self-locking snap hook
• Internal shock absorption
• Rugged, lightweight housing with corrosion
resistant components
Applications: Construction, industrial
maintenance, roofing and general work
at height.
Applications: Construction, industrial
maintenance, roofing and general work
at height.
CODE 4
04133 6m webbing
402117 6m cable
402118 10m cable
402119 15m cable
402120 20m cable
CODE 4
07372 6m
407373 10m
407374 15m
407375 20m
407376 30m
ULTRA-LOK™ RSQ SELF-RESCUE SRL
A unique self retracting lifeline providing
fall-arrest with assisted rescue capabilities or
automatic self rescue for ultimate versatility.
• 15m stainless steel cable lifeline
• Optional rescue pole available
• Self rescue mode automatically
lowers the user to the next level
after a fall
Applications: Truck tarping,
construction, industrial maintenance
CODE 405973 15m
ANCHORS
HOW STRONG IS YOUR
ANCHOR?
TRUSS ROOF ANCHOR
Roof anchor point for steel or tiled roof with
timber trusses.
• Easy installation
• All stainless steel 316 construction
• Rated up to 15kN
CODE 500999 L4544
PURLIN ROOF ANCHOR
Roof anchor point for steel roof with
steel purlins.
• All stainless steel 316 construction
• Rated up to 15kN
CODE 500837 L4543
When working at
height, your fall
protection system
is only as good as
the anchorage it is
connected to.
• Permanent D-ring style anchor
• Provides a compact, reliable connection
point for your fall protection system
• Attaches to the structure using fasteners
(not included)
• Rated to 22kN
• Can be bolted or welded to structure
• Two 14mm diameter attachment holes
(fixings not included)
• Stainless steel construction for durability
• Plate size: H = 6.35mm, W = 50mm,
L = 115mm
• Rated to 22kN
CODE 407790
CODE 407791
It is important that the anchorage
and the structure it is connected to is
capable of withstanding the forces
generated in the event of a fall.
Kilonewton (kN) is the measure of
force and is commonly used when
dealing with fall protection.
One kN is approximately equal to
100kg (1kN = 100kg). Therefore 15kN
is equivalent to 1500kg or 1.5 tonnes.
AS/NZS 1891 states the following
requirements for anchorage
strengths:
• 12kN for limited free-fall and abseil
• 15kN for 1 person fall-arrest
• 21kN for 2 people fall-arrest
CONCRETE D-RING ANCHOR
• A simple, versatile temporary or
permanent anchor
• Safe ‘hook-up’ indicator notifies the anchor
has been installed properly
• D-ring swivels 360 degrees
• Rated to 22kN
CODE 407792
TURNABLE ANCHOR EYES
• Single person fall-arrest anchor point
• Compact, swivels 360 degrees
• M16 bolt required (not supplied)
CODE 4
07829 Swivel
407830 Low profile
ANCHOR ON THE GO™
LADDER GRIP ANCHOR
A low-profile ladder anchor point that can
be permanently attached to the roof to
prevent a ladder from moving.
• Fall-arrest anchor point for 1 person
• Easy to install
• Supplied with a weather seal
and mounting rivets
CODE 405855
HEIGHT SAFETY
D-RING ANCHOR
D-RING BOLT-ON ANCHOR
Provides a safe and secure connection point
for maintenance and roof work.
• Fall-arrest anchor point for one person
• Easy to install
• Supplied with a weather seal
and mounting rivets
Temporary roof anchor for fall-arrest or
restraint on metal roof applications.
• 15kN fall-arrest rated anchor point
• Portable and re-usable single person anchor
• Large anchor eye allows for easy
attachment of fall-arrest system
• Easy-grip locking cam levers, for
tool-less installation and removal
CODE 405854
CODE 405390
MILLER FIX ROOF ANCHOR
47
TIE-OFF ADAPTORS & SLINGS
BEST PRACTICE GUIDELINES
Worksafe NZ has developed the
Best practice guidelines for working
at height in New Zealand.
HEIGHT SAFETY
These guidelines provide health
and safety guidance to all people
working at height and those involved
in the planning and preparatory
stages of any project that includes
working at height.
TIE-OFF ADAPTER
DUAL RING CABLE TIE-OFFS
Durable tie-off adapter for
anchoring to a variety of structures.
• Integral wear-sleeve
• Rated to 22kN
Lightweight and extremely durable
• Reposition without disconnecting or loosening
• Built in karabiner, self closing, self-locking
one-handed operation
• Rated to 22kN
CODE 4
07797 0.5m
402152 1.0m
500597 1.5m
402153 2.0m
CODE 4
09690 0.9m
409691 1.2m
409692 1.8m
ACCESSORIES
The guidelines outline how people
working at height and those involved
in the process can meet their
obligations under the HSE Act and
the HSE Regulations.
PERSONAL ENERGY ABSORBER
An essential resource
for everyone working
at height.
CODE 400820
• 300mm length
• Rated to 160KG
• Screw gate karabiner
on each end
DORSAL EXTENSION
For workers who cannot comfortably
reach the dorsal D-ring on their harness.
• Easy to retrofit to any harness
CODE 401685
DOWNLOAD IT FROM
NZSAFETY.CO.NZ TODAY
ROUND SLINGS
WEBBING TIE-OFF
Ideal for creating an anchorage for a
single person.
• Rated to 24kN
CODE 8
96017 1.0m
896018 2.0m
48
ANCHOR STRAP
1.5m round 25mm webbing anchor strap.
• Rated to 15kN
CODE 405091 1.5m
Durable 25mm tubular sewn slings.
• Special lengths can be made to order
• Rated to 25kN
• Made in New Zealand
CODE 4
06551 60cm
406552 100cm
406553 120cm
406554 150cm
406555 200cm
TEMPORARY HORIZONTAL LIFELINES
TEMPORARY
HORIZONTAL LIFELINES
An anchor that
moves with you
Fast set-up, removal and storage
with built-in tensioner and carry bag
• 18 metre webbing lifeline
• Includes two tie-off adaptors for
simple anchorage
• Built-in shock absorber preserves
the structure
• Fall arrest rated for two users
CODE 407789 18m
SAYFLINE™ TEMPORARY
HORIZONTAL LIFELINE KIT
• Complete kit with carry bag, easily installed
with no special tools
• Rope lifeline with integral tensioning device
• Includes two anchor straps
• Two runner pulleys for lanyard connection
• Rated for two people
CODE 4
03818 20m
500595 30m
WEBBING TEMPORARY
HORIZONTAL LIFELINE
Swing-Fall
When connected to a temporary
horizontal lifeline, it is important to
consider the effect of swing-fall (also
known as the pendulum effect). If a
fall takes place near the end or at an
intermediate anchorage, the mobile
anchorage device will run toward
the centre of the span (see diagram
below). This may cause the user
to collide horizontally with a fixed
object and knock off the line any
other users.
Fall Distance
While connected to a temporary
horizontal lifeline it is important to
consider the potential fall distance.
This can be significantly greater than
on a fixed anchorage due to the
potential deflection in the lifeline. The
system must be set up in such a way
so the worker will avoid striking a lower
level surface or obstacle. See below.
• 20m webbing with ratchet tensioner
• Easy to install and remove from site
• Complete with storage bag sewn to line
• For up to two people
CODE 500594 20m
YOU NEED TO
BE PROPERLY
TRAINED TO
WORK SAFELY
AT HEIGHT.
See page 10-14 for
more information.
Temporary horizontal lifelines are an
excellent solution when mobility is
required over an area between two
anchor points.
HEIGHT SAFETY
PRO-LINE TEMPORARY
HORIZONTAL LIFELINE KIT
EZ-LINE RETRACTABLE
HORIZONTAL LIFELINE
• Simply pull out for installation and retract
for dismantling
• Customise your length up to 18 metres
• Built-in tension and impact indicators takes the
guesswork out of system set-up and service
• Continuous protection for up to two people
per span and up to six people
per system
CODE 403736 18m
49
CONFINED SPACE ACCESS
DBI-SALA CONFINED
SPACE SYSTEM
THE HEALTH
& SAFETY IN
EMPLOYMENT ACT
1992 REQUIRES
WORKERS TO BE
TRAINED WHEN
ENTERING A
CONFINED SPACE.
ROPE POSITIONING DEVICE
Ideal for rescue/retrieval and confined space
applications.
• Supplied with 60m of 9mm kernmantle rope
to deliver 15m of travel
• Inertia speed brake automatically activates
if you become unconscious
• Complete kit includes anchor strap,
karabiners and rescue strop
CODE 500603
TRIPOD
Portable, lightweight aluminium tripod with
leg connection chains for added stability .
• DBI-SALA winch mount included
• Integrated dual pulley system for winch cable
• Two additional anchor points
HEIGHT SAFETY
CODE 5
00602 2.75m
402149 2.13m
Note: Only compatible with DBI-SALA
branded winch/retrieval block
We offer NZQA
accredited courses in:
• Confined Space Entry
& Planning
• Atmospheric Testing
• Permit Issue & Receiver
• Self Contained
Breathing Apparatus
(SCBA)
RESCUE MASTER KIT
Designed for rescues from confined
space or other difficult to access areas.
Kit includes:
• Pulley system and 11mm kernmantle rope
• 2 x karabiners
• Webbing tie-off adaptor
• Storage bag
CODE 5
00083 RM 45M-L 3:1 Ratio
500099 RM 60M-L 4:1 Ratio
SEALED RETRIEVAL
SELF-RETRACTING LIFELINE
Sturdy design for the most arduous confined
space environment.
• Supplied with 15m of 5mm galvanised cable
• Stainless steel internal components and cast
aluminium housing for corrosion resistance
• Built-in retrieval winch
CODE L 3402 15m
L3402096 Mounting bracket for connection
to tripods
SPREADER BAR
SALALIFT® II WINCH
•A
ttaches to harnesses incorporating
confined space loops.
• Complete with double action karabiners
• Adjustable rescue wrist straps
• Spreader frame attaches to the confined
space loops on a harness
• Top D-ring can be attached to a raising
and lowering device
• Wrist loops assist in casualty removal from a
confined space
For routine work support and rescue/retrieval
from confined spaces.
• Easy operation - 6:1 gear ratio
• Supplied with 18m of 6mm galvanised cable
• Quick-mount system
CODE 500580
CODE 818119
SPREADER BAR
50
CODE 500605 18m
PROTECTA CONFINED
SPACE SYSTEM
MILLER CONFINED
SPACE SYSTEM
Don’t want
to own it?
HIRE IT!
Tripod
TRIPOD
Light weight aluminium confined space tripod.
• Adjustable legs with non-slip feet
• Includes four anchorage points
• Lightweight, strong aluminium tripod
• Adjustable legs with non-slip feet
• Provides a 22kN anchor (vertical pull)
CODE 400068 2.35m
CODE 8
94915 TRI/7 2.26m
896284 TRI/9 2.92m
500600 CP105 Optional Pulley (not shown)
Note: Only compatible with Protecta branded
winch/retrieval block
NOTE: Only compatible with Miller branded
winch/retrieval block
+
Winch
+
Gas Detector
MIGHTEVAC™ RECOVERY REELS
• 15m of galvanised cable
• 7.4:1 mechanical advantage
• Mounting bracket sold separately
Recovery fall arrestor with 4:1 mechanical
advantage retrieval winch for
emergency evacuation.
• Galvanised cable
• 15m or 30m lengths
• Includes mounting bracket
• Aluminium housing with stainless steel
components
CODE 4
11351 Protecta Type3 retrieval device
411352 Bracket
CODE 8
96071 15m MR15MGB
896098 30m MR30MGB
RETRIEVAL BLOCK
+
Harness
HEIGHT SAFETY
TRIPOD
=
Confined
Space Access
MANHANDLER® WINCH
WINCH
• 20m of stainless steel cable
• 4.5:1 mechanical advantage
• Anti-release and auto-lock safety system
Designed for work positioning and emergency
rescue from confined spaces.
• 18m of galvanised cable
• Over speed breaking mechanism
CODE 400634 20m
CODE 894918 18m
All confined space access
equipment available for daily,
weekly or monthly hire.
TALK TO NZ SAFETY ABOUT
YOUR REQUIREMENTS.
51
VERTICAL SYSTEMS
ADVANCED PORTABLE
FALL ARREST SYSTEM
HEIGHT SAFETY
ADVANCED
FIVE-PIECE HOIST SYSTEM
CODE 4
04118 Five piece system
406171 Upper mast
406172 Lower mast
406173 Portable base
406174 Vehicle hitch mount
404117 Wall mount
404116 Floor mount
404120 DBI-SALA winch bracket
CODE 4
03487 PFAS Post
403648 Weld-on base plate with anchor
404115 Rescue davit arm
408395 PFAS bag
Attachments and accessories
sold separately.
DURAHOIST™ FOUR PIECE
CONFINED SPACE SYSTEM
DURAHOIST™ PORTABLE
ANCHOR POST
• Lightweight, easy storage, transport and
set-up, no tools required
• Height of mast is adjustable
• Adjustable feet for uneven surfaces
• Quick release joins for easy collapsibility
and transport
Provides three independent swivelling tie-off
fall-arrest anchorage points.
• Telescoping design and aluminium
construction for easy transportation
and setup
• Can be installed vertically on applications
with inclines up to 15 degrees
• Optional Davit Arm available for materials
handling or rescue and access needs
CODE 4
03922 DH-3 One piece mast
403923 DH-4 Portable base
403926 DH-19-MILLER winch bracket
403924 DH-8ZP Wall mount sleeve
403925 DH-7ZP Floor mount sleeve
404713 DH-12 Vehicle hitch mount
404714 DH-16 Tow ball adapter
sold separately.
52
• Compact and lightweight design makes the
post very easy to transport and put in place
• Three independent anchor points rotate
360 degrees, for up to three workers
CODE 4
03927 DH-AP-1 Portable fall arrest post
403928 DH-AP-4 Base plate with anchor
403930 DH-AP-3 Rescue davit arm
sold separately.
CABLOC™ VERTICAL LIFELINE KIT
• User installed ladder safety system for
fixed ladders
• Sleeve follows user for hands-free climbing
• Stainless steel construction
• Ideal for a variety of structures
CODE 4
10657 10m
410658 20m
410659 30m
LAD-SAF™ VERTICAL SYSTEMS
• Rugged and corrosion resistant
galvanised construction
•U
ser installed ladder safety system for fixed
ladders (cable available separately)
• Sleeve follows user for hands-free climbing
•B
uilt in energy absorber protects user
and structure
•A
ccommodates up to 2 workers
at one time
CODE 4
00886 Bolt on kit
400707 Cable, per metre
411347 Lad-Saf sleeve
411348 Bolt on cable guide
ENGINEERED FIXED SYSTEMS
ENGINEERED SAFETY
DBI-SALA® Engineered Systems
Custom solutions designed the way you want!
You can always depend on DBI-SALA®’s
horizontal safety systems for mobility and safety
when working at height. A comprehensive
range of height safety products offering fully
compliant, practical solutions for structures of all
types, in all industries. Engineered fall protection
systems are used to protect workers while
working at height who may not have continuous
access to suitable anchorage points.
Miller® fall protection
systems
Every permanently installed system offers
comfort, mobility and safety combined with
ease of use, flexibility and low maintenance.
• Railcars
• Cranes
• Truck trailers
• Rooftops
• Buses/mass transit
• Window washing
• Commercial buildings
• Warehouses
• Aircraft hangers
• Bridges
Miller ® Engineered Systems provides
innovative and superior fall arrest
solutions for unique safety challenges.
The range of systems is specifically
designed to enhance worker safety
and productivity while increasing
compliance and lowering overall
cost. Our systems include: Multi-Rail
horizontal rail system; Vi-Go vertical
cable system; Glideloc ® horizontal
and vertical ladder systems; and
Xenon horizontal lifeline and
overhead lifeline systems.
XENON
SHOCK ABSORBER
HEIGHT SAFETY
Designed for optimum performance and worker
satisfaction, engineered systems are typically
required in the following sites and applications:
VI-GO SHUTTLE
NZ SAFETY UTILISES A NETWORK OF FULLY TRAINED,
CERTIFIED INSTALLERS PROVIDING INDUSTRY
LEADING INSTALLATION SERVICES OF THE DBI-SALA
ENGINEERED SYSTEMS RANGE.
CONTACT NZ SAFETY FOR AN ON-SITE ASSESSMENT
BY A DBI-SALA TRAINED CONSULTANT TO PROVIDE A
CUSTOMISED, COST EFFECTIVE SOLUTION.
53
RESCUE EQUIPMENT
HEIGHT SAFETY
ROLLGLISS®
R250 RESCUE KIT
Designed for the rescue of a worker left
suspended at height after a fall.
• Lightweight, portable and easy to operate,
no specialist tools required
• Large hook makes it easier to connect to
the suspended person
• Kit includes R250 descender with karabiner,
rope and safety hook, extension pole,
mini-haul system anchorage strap, and
two carry bags
CODE 4
03067 20m
403150 50m
ROLLGLISS®
RESCUE LADDER
RIGGERSMATE™
AUTO LOCK HAUL KIT
Provide assisted rescue after a fall, can be
anchored to a structure and dropped down to
the victim’s level so they can climb to safety.
• Ladder rungs are rigid and reinforced
• Available in 2.4m sections – extra sections
can be added to lengthen
• Includes three connecting karabiners
• The optional anchorage plate is ideal for
confined-space entry systems
• Compact grab ‘n’ go auto lock rescue/
haul system
• Built-in rope guides
• Kit includes 2 x screw gate karabiners,
1 x double sheave progress capture head,
1 x double sheave pulley,
1 x kernmantle rope and 1 x kit bag
• NFPA 1983 certified as a system as provided
by the manufacturer
CODE 4
04784 Rescue ladder
404785 Anchorage plate
CODE 4
03067 20m
403150 50m
ACCESSORIES
SCAFFOLD HOOK
Compatible with 405999
scaffold hook.
Large aluminium double-action
scaffold hook.
• Gate opening: 62mm
• Rating: 25kN
CODE 409700
CODE 405999
ROLLGLISS® RESCUE POLE
RESCUEMATE
MICRO-HAULER
Kit includes:
• 1 x triple sheave
Rescuemate Micro Hauler
• 1 x triple sheave pulley
• 1 x locking karabiner
• 1 x quick link
• 1 x mini Explorer
• 14m x 8mm rope and kit bag
CODE 4
07780 Kit
407779 Bag only
ROLLGLISS™
R550 RESCUE KIT
Emergency rescue and evacuation from a
wide variety of elevated work areas
• Kit includes kernmantle rope lifeline,
descent kit with rescue lifting handle,
karabiner and carry bag
• Fully automatic controlled descent
• Built-in rescue lifting handle
• Integrated pigtail and cam cleat
• Compact and lightweight design
• 9mm (20m. 40m and 60m) kernmantle
rope lifeline
• Rated for up to 500m height for one user,
175m for two users
CODE 4
10667 20m
410668 40m
410669 60m
54
SAFESCAPE™ ELITE RESCUE
DESCENDER
Easy to setup, adjust and use, even in the
harshest conditions.
• Can be used over an edge with rope
protector or pulley
• Incorporates a wheel and handle for lifting
• Custom lengths manufactured on request
• Can provide descents of up to 500m
• Rated for two persons (250kg max)
CODE 4
05613 20m
405614 40m
405615 80m
EVAC BODY SPLINT
• Wrap-around design, suitable for rescues
from confined spaces
• Becomes rigid when in use
• Can be lifted vertically or horizontally
CODE 817317
ROPE & KARABINERS
ROPE-SAFE™
ROPE GRAB
• Designed to fit 10.5mm to
13mm kernmantle rope
• Rated for single person fall arrest
or two person rescue 200kg
• Anti-panic grip, and is switchable from
Manual to Automatic
VIPER ROPE GRAB
Cost-effective and
compact steel rope grab.
• Can be connected at any
point along the rope
• Suited to 11–13mm
kernmantle rope only
CODE 4
11349 with 300mm shock absorbing lanyard (pictured)
411350 with 900mm shock absorbing lanyard pack
KERNMANTLE ROPE
ACCESSORIES
11.5mm or 13mm rope for abseiling, rescue
and general lifelines.
COBRA™ ROPE GRAB
• Automatic or manual mode
• Designed for use on
12–14mm twisted rope
• Approved for use on 11-13mm
kernmantle rope when fitted
with integral shock pack
PVC ROPE BAGS
• Shoulder straps
• Drawstring closure
• Made in New Zealand
CODE 4
05992 50m
405993 100m
11.5MM
CODE 4
04038 10m
404039 20m
404040 30m
404041 50m
405990 200m
817236 per metre
13MM
CODE 4
05729 with shock pack (pictured)
400821 no shock pack
CODE 4
05991 200m
405730 per metre
AUTO-LOCK ALUMINIUM KARABINER
AUTO-LOCK ALUMINIUM KARABINER
• 18mm gate opening
• Lightweight aluminium
• Self closing triple action auto-lock gate
• Rating: 30kN
• 23mm gate opening
• Lightweight aluminium
• Self closing double action auto-lock gate
• Rating: 25kN
CODE 410661
CODE 410662
PVC ROPE BAGS
• Heavy duty
• Versatile handles
• Secure closure system
CODE 4
10653 Small - Yellow 25L
410654 Medium - Green 40L
410655 Large - Orange 50L
410656 X-Large - Red 60L
AUTO-LOCK KARABINER
SCREW-GATE KARABINER
• Built in sealed ball bearings
• High strength aluminium construction
• Rating: 40kN
D-shape, zinc-plated steel double-action
auto-lock karabiner.
• Rating: 50kN
Large volume, wide opening D-shape,
zinc plated steel double action
screw-gate karabiner.
• Rating: 50kN
CODE 410663
CODE 405996
CODE 405994
TRIPLE ACTION KARABINER
SCREW-GATE KARABINER
Large volume, wide-opening D-shape,
zinc-plated steel triple action karabiner.
• Rating: 50kN
Oval shape, alloy steel double-action
screw-gate karabiner.
• Rating: 25kN
CODE 405995
CODE 401325
SWIVEL CONNECTOR
AUTO-LOCK KARABINER
Alloy steel double action
auto-lock karabiner.
• Captive eye slot
• Rating: 35kN
CODE 400598
HEIGHT SAFETY
CODE 402948
55
ROPE ACCESS
RESCUE EQUIPMENT
IS ESSENTIAL
HEIGHT SAFETY
Do you
have a
rescue
plan in
your height
safety
system?
AVAO HARNESS
• Front, rear & abdominal aluminium D-ring
• Tool and gear loops
• Waist belt with side aluminium D-rings
Sizes: S, M, L, XL
• Front, rear & abdominal D-rings
• 6x tool/gear loops
• Waist belt with side D-rings
Sizes: 1, 2
CODE 408303 With chest ascender (pictured)
408304 No chest ascender
409693 Suspension seat
405964 Lower body harness
CODE 4
10284 BOD harness
410481 Bod Fast harness
410482 Bod Croll Fast harness
405978 Podium work seat
ACCESSORIES
VERTEX HELMETS
LINEWORKERS HELMET
Helmet for work at height
and rescue.
• Chinstrap designed to reduce
the risk of the helmet falling off
as a result of an impact during a fall
• Accessories can be easily added
• Vertex Best approved to CE ANSI
Z89.1-2003 Type 1 Class E
• Vertex Vent approved to CE EN 12492,
ANSI Z89.1-2003 Type 1 Class C
Designed for working at
height with the added security
of a four-point head harness
to keep it in place in the event
of a fall.
• Ratchet suspension system
• Peak-less option for added
range of vision
• Approved to
AS/NZS 1801:1997 Type 1
CODE 4
06783 Vertex Best
406784 Vertex Vent
CODE 4
04360 Peak
550464 Peak-less
ROCKER ROPE GRAB
• Light-weight alloy construction
• Manual or automatic rope grab
• For use with 12mm polyester or 11mm
kernmantle rope
CODE 896200
56
EXOFIT NEX™
ROPE ACCESS HARNESS
ASAP ROPE GRAB
SHOCK ABSORBERS
Mobile fall-arrester for kernmantle rope.
• Stops a fall, a slide or an uncontrolled descent
• Works on vertical or angled rope
• Can be installed at any point along the rope
• ABSORBICA is often used in combination
with a lanyard to build an energy-absorbing
lanyard with a maximum length of 2.0m
• ASAP’SORBER is designed to connect the
ASAP mobile fall arrester to a harness
CODE 4
03259 200mm Energy Absorber
405981 400mm Energy Absorber
CODE 4
05982 ABSORBICA
407173 ASAP’SORBER 20cm
ABSORBICA-Y LANYARD
PROGRESS LANYARD
GRILLON POSITIONING LANYARD
• Twin tail energy-absorbing lanyard with
double 60mm aluminium scaffold hooks
• Total length 1.05m
Note: Requires a karabiner (not included) for
connection to the user’s harness.
• Limited fall applications only
• Dynamic rope construction limits the
energy transmitted during a limited fall
• Short tail: 30 cm Long tail: 65 cm
Note: Karabiners are not included.
• 3.0m adjustable lanyard for work positioning
• Length can be very easily and precisely
adjusted
Note: Does not include karabiners.
Not suitable for fall-arrest.
CODE 405600 L59 MGO
CODE 405984 L44
CODE 405977 L52A 003
ROLLGLISS® EXPLORER™ ASCENDER
ASCENSION
• Ergonomic comfort grip handle
• Stainless steel eyelet in main bottom rigging
hole to reduce wear
• Suits 10.5-13mm rope
• Ergonomically moulded handle for comfort
and thermal insulation
• Lower holes for connecting a lanyard or
foot loop
CODE 4
07781 Right
407782 Left
CODE 4
03262 B17 LH Black
403261 B17 RH Yellow
ROLLGLISS®
NOWORRIES™ DESCENDER
RIG DESCENDER
I’D DESCENDER
• Two way stop mechanism
• Simple to thread and operate for
hassle-free descent or belay
• Capable of two person descent
• Compact self-braking descender
• Designed for expert rope access users
• Multi-function handle
• For single ropes 10.5mm–11.5mm
in diameter
• Self-braking descender for rope access
and rescue
• Integrated anti-panic function and
anti-error catch
CROLL ASCENDER
CODE 8
94974 8700387 for 11mm rope
407778 8700388 for 13mm rope
FOOT TAPE
Adjustable webbing foot loop
for rope ascents.
• Attaches to the Ascension
• Length easily adjusted with
DoubleBack buckle
CODE 405980 C47A
CODE 405979 D21A
ROLLGLISS®
SINGLE & DOUBLE PULLEYS
• Single: 60mm diameter,
Double: 50mm diameter
• Suits rope up to 13mm
CODE 4
07772 8700034 Single Pulley
407771 8700014 Double Pulley
Ventral rope clamp used with the
ASCENSION rope clamp for ascending a rope.
• Toothed cam with self-cleaning slot
•M
echanism is totally integrated into the body
of the rope clamp to help
prevent rubbing
CODE 405983 B16BAA
HEIGHT SAFETY
ROPE ACCESS
CODE 4
03258 I’D S (10mm – 11.5mm rope)
404359 I’D L (11.5mm – 13mm rope)
RESCUE PULLEY
High-strength, high-efficiency pulley for
rescue professionals.
• Designed for heavy loads or intensive use
• Large diameter sheave mounted on sealed
ball bearings for excellent efficiency
CODE 404129 P50A
57
TOOL SAFETY
TOOL LANYARDS
Prevent falling objects
There’s nothing more dangerous than
a plummeting tool.
HEIGHT SAFETY
Regardless of shape or size, power or
manual, bucket or bag, we have a
tool safety solution to help keep tools
from attacking.
SQUIDS® WRIST TOOL LANYARD
SQUIDS® SINGLE KARABINER
TOOL LANYARD
• Polyester webbing cuff
• Tether length 19cm
• Maximum safe working capacity: 0.9kg
• Sizes: S/M, L/XL
• Black
• Stretch cord with nylon webbing
• Stainless steel karabiner with screwgate
• Maximum safe working
capacity: 6.8kg
• Lime
CODE 4
10969 - S/M
410970 - L/XL
CODE 4
10974 89-107cm (Standard)
410975 107-137cm (Extended)
SQUIDS® DUAL KARABINER
TOOL LANYARD
• Stretch cord with nylon webbing
• Heavy duty (8KN) triple-locking karabiner
with 360 degree captive-eye
• Maximum safe working capacity: 9kg
• Lime
ARSENAL® TOOL BUCKET WITH LID
• Leather reinforced base
• PP rope handle
• Maximum safe working
capacity: 68kg
CODE 4
10967 89-107cm (Standard)
410968 107-137cm (Extended)
CODE 4
10972 32cm(D) x 43cm(H)
410973 25cm(D) x 71cm(H)
TOOL SAFETY STRAPS
BANDIT TOOL LANYARD
Fall protection for your tools. Protect people
working below by using tool straps to secure
your tools to your tool belt, harness or wrist.
• Capacity of 4.5kg
• Conveniently attaches to the user’s belt
• Tool attachment via small karabiner
or adjustable clinching cord
• Elasticised cord for greater worker flexibility
• 800mm retracted and1.2m fully extended
• Maximum tool weight 2.26kg
Featuring tough stretch cord, rugged
nylon outer sleeves and more than
capable weight capacity.
Tool lanyards
improve site safety
CODE 4
07775 1150911 elastic lanyard
405958 E815 tool lanyard with clip
405959 E814 adjustable tool strap with velcro
58
CODE 404132

height safety - NZ Safety Online Catalogue

Transcription

Similar documents

gemtor harness positioning loops

Safety Tool Box Talk..

Trip to Chudleigh`s Farm

Technical Information

Product Catalog

Self Retracting Lanyard Leaflet

1891 Jamaica Exhibition

3 EASY WAYS TO ORDER

2007 Suzuki GSXR1000 Dynojet Research 2191 Mendenhall Drive

PRO press release