Commercial Plumbing

Comments

Transcription

Commercial Plumbing
COMMERCIAL
PLUMBING PRODUCTS
Commercial Plumbing Products: Table of Contents
PRODUCT CATEGORY
FIXTURES
SECTION
PAGE
High Efficiency Urinals ........................................................ 2
Two-Piece Toilets ................................................................. 2
High Efficiency Toilets (HET) ...............................................
3-4
Elementary Toilets ............................................................... 4
Toilet Seats .......................................................................... 5
Flush-Valve Toilets .............................................................. 5
Wall-Mount Lavatories ......................................................... 6
Countertop Lavatories .......................................................... 7
Undercounter Lavatories ...................................................... 8
Stainless Steel Sinks ............................................................ 9-10
Floor and Laundry Sinks and Accessories ............................ 11
Molded Basins and Accessories ........................................... 12-13
Enameled Steel Tubs ............................................................ 14
Heavy Duty Commercial Faucets ........................................... 15
FAUCETS
SECTION
Lavatory Faucets .................................................................. 16-17
Bar Faucets .......................................................................... 17
Kitchen Faucets .................................................................... 18-19
Service Faucets .................................................................... 19-21
Bath and Shower Accessories .............................................. 22
ROUGH
SECTION
Access Doors ....................................................................... 23
Sink and Drain Accessories .................................................. 23–24
Trap Primers and Accessories .............................................. 25
Lavatory Supply Kits ............................................................ 25
Closet Supply Kits ................................................................ 26
Heavy Pattern Supply Kits ................................................... 26
ADA Lavatory Supply Kit ...................................................... 26
Individual Stops ................................................................... 27
Heavy Individual Stops ......................................................... 27
Water Hammer Arrestors ..................................................... 28
No-Hub Couplings ................................................................ 29
www.PROFLO.com
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
High Efficiency Urinals
13-1/2"
(345)
PF1815WH
•
•
•
•
•
•
•
•
•
•
High efficiency 0.5-1.0 gpf / 1.9-3.8 Lpf
Rear outlet
Integral flushing rim and trap
Siphon-jet flushing action
3/4” (19mm) top inlet spud
2” (51mm) NPT inside thread outlet
Hanging brackets included
Flush valve not included
Available in white (WH) only
ADA compliant*
16-1/4"
(410)
22-1/4"
(565)
1-3/4"
(45)
2-15/16"
(75)
3/4” x 3/8"
(18x10)
4"
(100)
14"
(356)
PF1805WH
•
•
•
•
•
•
•
•
•
•
13-13/16”
(350)
High efficiency 0.5-1.0 gpf / 1.9-3.8 Lpf
Bottom outlet
Integral flushing rim and strainer
Wash-out flushing action
3/4” (19mm) top inlet spud
1-1/2” (38.1mm) outlet for exposed trap connection
Wall-hanging brackets included
Flush valve not included
Available in white (WH) only
ADA compliant*
3-1/2”
(90)
20-3/4”
(528)
5-5/8”
(143)
6-3/16”
(157)
14-1/2”
(368)
17-1/2”
(445)
16-15/16”
(430)
PF1825WH
•
•
•
•
•
•
•
•
•
•
High efficiency 0.5-1.0 gpf / 1.9-3.8 Lpf
Half stall, rear outlet
Integral flushing rim and trap
Wash-out flushing action
3/4” (19mm) top inlet spud
2” (51mm) NPT inside thread outlet
Hanging brackets included
Flush valve not included
Available in white (WH) only
ADA compliant*
3-3/8”
(85)
1-3/8”
(35)
26-3/4”
(680)
14-3/16”
(160)
14-5/8”
(372)
15-3/4”
(400)
15-3/8”
(390) 21-1/2”
(545)
3-1/8”
(80)
5-1/16”
(128)
4”
(100)
1”
(25)
5/8”
(16)
4”
(100)
2-13/16”
(72)
7-7/8”
(200)
18-1/8”
(460)
17-1/8”
(435)
PF1835WH
• High efficiency 0.5-1.0 gpf / 1.9-3.8 Lpf
• Half stall, rear outlet
• Integral flushing rim and trap
• Siphon-jet flushing action
• 3/4” (19mm) top inlet spud
• 2” (51mm) NPT inside thread outlet
• Hanging brackets included
• Flush valve not included
• Available in white (WH) only
• ADA compliant*
*All products listed as ADA compliant meet ADA requirements as stated in the American Disabilities Act when
installed in accordance with ADA guidelines.
3-3/8”
(85)
11-7/8”
(300)
1-3/8”
(35)
28-1/8”
(715)
14-3/16”
(360)
15-3/8”
(390)
15-3/4”
(400)
15-3/8”
(390) 21-1/2”
(440)
3-1/8”
(80)
5-1/16”
(128)
4”
(100)
1”
(25)
5/8”
(16)
4”
(100)
2-13/16”
(72)
7-7/8”
(200)
1
Two-Piece Toilets
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
PF1401JWH, PF5112WHM (bowl & tank)
FINISHED WALL LINE
30-1/4”
(768 mm)
1”
(25)
8-3/8”
(214)
15-3/4”
(417)
28-7/8”
(734 mm)
18-1/2”
(470 mm)
3-1/2”
(89)
14-5/8”
(373 mm)
CL
SUPPLY
12”
(305)
CL
OUTLET
FINISHED
FLOOR LINE
5”
(127)
•
•
•
•
•
•
•
•
•
•
Elongated bowl
Gravity fed (1.6gpf/6.0Lpf)
Box rim
2” fully glazed trapway
8” x 9” water surface
Anti-siphon fill valve
Close coupled tank with cover
Quick connect, 2 bolt tank to bowl installation
Standard color match trip lever
10” (254mm), 14” (355.6mm), RH trip lever, and lined
tanks are also available
• Available in white (WH) and biscuit (BS)
• Locking tank available (PF5112LWHM)
PF1403JWH
• 17” (432mm) ADA compliant* bowl height
18-9/16”
(472 mm)
14-5/8”
(372 mm)
Wall
27-3/4”
(706 mm)
14-1/2”
(368 mm)
3/4” * 3/4”
(20 mm * 20 mm)
18-3/4”
(477 mm)
18-1/2”
(470 mm)
15”
(380 mm)
16-1/2”
(419 mm)
Floor
2
Supply
5”
PF1705WH, PF1710WH (bowl & tank)
• Wall-mounted elongated bowl
• Gravity fed (1.6gpf/6.0Lpf)
• 2” fully glazed trapway
• Meets ADA requirements
• Standard seat installations (sold separately)
• Siphon Jet Bowl
• Meets ASME A112.19.2, CSA B45
www.PROFLO.com
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
High Efficiency Toilets
Wall
PF1601PAWH, PF1612PAWH (bowl & tank)
•
•
•
•
•
•
•
•
•
•
•
•
1”
(25.5)
30-3/4”
(780)
Elongated bowl
Uses 35% less water than standard low-consumption toilets
1.0 gpf/3.79 Lpf high efficiency with Pressure Assist
Sloan FLUSHMATE IV System
Siphon-jet flushing action
Large 13-1/2” x 11” (342.9mm x 279.4mm) water surface
2” (51mm) fully-glazed trapway
EPA WaterSense certified
Anti-siphon ballcock prevents back-siphoning
RH trip lever tanks available (PF1612PARWH)
Available in white (WH) only
Locking tank available (PF1612PALWH)
9-1/6”
(233)
19-1/2”
(497)
18-1/2”
(470)
28-1/4”
(718)
14”
(356)
12”
(305)
Rough in
Floor
5”
(127)
Supply
20-1/4”
(512)
10-1/4”
(260)
PF1603WH
• 17” (432mm) ADA compliant* bowl height
PF1600PAWH
• Round Front bowl
Wall
1”
PF1605PAWH
9-1/2”
(240 mm)
• Elongated bowl
• Floor mount back outlet
29” Round Front
31-3/16” Elongated
31-1/8” ADA
20-7/8”
(530 mm)
29-3/4” Round Front
29-3/4” Elongated
31-3/4” ADA
16-5/8” Round Front
18-3/4” Elongated
18-3/4” ADA
PF1604PAWH
• Round Front bowl
• Floor mount back outlet
PF1606PAWH
• 17” (432mm) ADA compliant* bowl height
• Floor mount back outlet
29-3/4” Round Front
29-3/4” Elongated
31-3/4” ADA
8-1/8”
(208 mm)
4”
(104 mm)
25-1/16” Round Front
26” Elongated
26-1/4” ADA
FINISHED WALL LINE
PF9301JWH, PF9312WH (bowl & tank)
•
•
•
•
•
•
•
•
Elongated bowl
Dual-flush, high efficiency 1.6 gpf / 6.0 Lpf or 1.1 gpf / 4.16 Lpf
Gravity-fed box rim
9” x 7” (228.6mm x 177.8mm) water surface
2” (51mm) glazed trapway
Color-matched trip lever
EPA WaterSense certified
Available with 10”, 12” or 14” RI, RH trip lever or insulated tank
PF9303JWH
• 17” (432mm) ADA compliant* bowl height
• Available in white (WH) only
*All products listed as ADA compliant meet ADA requirements as stated in the American Disabilities Act when
installed in accordance with ADA guidelines.
Supply
5”
(127 mm)
Floor
30-1/4”
(768)
1”
(25)
8-3/8”
(214)
15-3/4”
(417)
28-7/8”
(733)
18-1/2”
(470)
3-1/2”
(89)
14-5/8”
(371)
CL
SUPPLY
12”
(305)
CL
OUTLET
FINISHED
FLOOR LINE
5”
(127)
3
High Efficiency Toilets
PF9401WH, PF9412WHC (bowl & tank)
FINISHED WALL LINE
•
•
•
•
•
•
•
•
•
•
Elongated bowl
Uses 20% less water than standard low-consumption toilets
High efficiency 1.28 gpf /4.85 Lpf
High performance 3” (76.2mm) flush valve
Gravity-fed, double-jetted box rim
8-1/2” x 7” (215.9mm x 177.8mm) water surface
2” (51mm) glazed trapway
EPA WaterSense certified
Available in white (WH) and Biscuit (BS)
Available with 10”, 12” or 14” RI, RH trip lever
or insulated tank
• Locking tank available (PF9412LWH)
30-1/4”
(768)
8-3/8”
(214)
1”
(25)
18-5/8”
(477)
30-1/8”
(765)
18-1/2”
(740)
CL
16-1/8” SUPPLY
(410)
CL
SUPPLY
FINISHED
FLOOR LINE
CL
12”
(305)
OUTLET
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
PF9403WH
5”
(127)
• 17” (432mm) ADA compliant* bowl height
Seats and Supplies not included.
FINISHED WALL LINE
A
ADA
PF1403HE
30-1/4”
30-1/4”
B
18-1/2”
18-1/2”
C
14-5/8”
17”
D
28-7/8”
31-1/4”
15-3/4”
(417)
8-3/8”
(214)
1”
(25)
EL
PF1401HE
A
D
B
3-1/2”
(89)
PF1401HE, PF5112HE (bowl & tank)
•
•
•
•
•
•
•
•
•
•
C
Elongated bowl
Uses 20% less water than standard low-consumption toilets
High efficiency 1.28 gpf /4.85 Lpf
High performance 3” (76.2mm) flush valve
Color-matched trip lever.
Anti-siphon fill valve.
8” x 9” (203.3mm x 190mm) water surface
2” (51mm) glazed trapway
EPA WaterSense certified
Available with 10”, 12” or 14” RI, RH trip lever
or insulated tank
CL
SUPPLY
PF1403HE
12”
(305)
CL
5”
(127)
FINISHED
FLOOR LINE
OUTLET
• 17” (432mm) ADA compliant* bowl height
• Available in white (WH) and biscuit (BS)
Elementary Toilets
WALL
1”
(25)
8-3/8”
(213)
PF1704BBWH, PF1712BBWH (bowl & tank)
26-3/8”
(670)
15-3/4”
(400)
25”
(635)
10-1/4”
(260)
10”
(254)
ROUGH IN
9-7/16”
(239)
18-11/16”
(475)
SUPPLY
5” (127)
•
•
•
•
•
•
•
•
•
•
Round front bowl
1.6 gpf / 6.0 Lpf gravity fed
Siphon-jet flushing action
10-1/4” (260mm) high bowl for child use
10” (254mm) rough-in
3” (76.2mm) flush valve
Sanitary bar on bowl
Two-bolt tank-to-bowl installation
Available in white (WH) only
Locking tank available (PF1712BBLWH)
Wall
13-3/8”
(340)
22-5/8”
(575)
13”
(330)
PF1700BB
• Flush valve round-front bowl
• 10” (254mm) high bowl
• 1.6 gpf/6.0 Lpf
10”
(254)
10”
(254)
Rough In
4
10-5/16”
(465)
Floor
8-11/16”
(220)
PROFLO fixtures have a one-year limited warranty and meet or exceed the following standard: ASME A112.192;
IAPMO/cUPC listed; CSA approved. High efficiency toilets are LEED and LADWP compliant.
www.PROFLO.com
Toilet Seats
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
PFTSBB1000WH
• For use with elementary
bowls PF1704BB and PF1700BB
• Round front only
• Available in white (WH) only
PFTSCOF2000WH
PFTSCOFH2000WH - Extra Heavy Duty
PFTSCOFA2000WH - Anti-Microbial
PFTSCOF2000BL - Black
PFTSCOFE2000WH - Standard Check Hinge
•
•
•
•
•
•
Elongated open-front less cover
Heavy-weight molded solid plastic
304 Series stainless hardware
Molded in color-matched bumpers
Slip-resistant pads
Self-sustaining check hinge
PFTSCOFC2000WH - Open Front with cover
Heavy weight molded solid plastic seat.
Molded in color matched bumpers
Flush-Valve Toilets
PF1721WH
•
•
•
•
•
•
•
•
Elongated bowl
High efficiency 1.28 gpf / 4.85 Lpf
Uses 20% less water than 1.6 gpf / 6.0 Lpf toilets
Siphon-jet flushing action
1-1/2” (38.1mm) top inlet spud
12-1/4” x 11-1/4” (311mm x 286mm) water surface
Compatible with 1.28 gpf, 1.6 gpf and Dual Flush flush valves
Available in white (WH) only
15-1/8”
(383)
WALL
13-7/8”
(353)
30-3/4”
(780)
17”
(432)
ADA
13-5/8”
(346)
PF1723WH
• 17” (432mm) ADA compliant* bowl height
• Available in white (WH) only
10”
(254)
ROUGH IN
PF1731WH
•
•
•
•
•
•
•
•
•
Elongated bowl
High efficiency 1.28 gpf / 4.85 Lpf
Uses 20% less water than 1.6 gpf / 6.0 Lpf toilets
Siphon-jet flushing action
1-1/2” (38.1mm) top inlet spud
12 x 10” (305mm x 254mm) water surface
Compatible with 1.28 gpf, 1.6 gpf and Dual Flush flush valves
ADA compliant*
Available in white (WH) only
FLOOR
20-1/4”
(512)
10-1/4”
(260)
Wall
24-3/4”
(630)
14-1/2”
(370)
13-1/4”
(335)
Wall
*All products listed as ADA compliant meet ADA requirements as stated in the American Disabilities Act when
installed in accordance with ADA guidelines.
5
Wall-Mount Lavatories
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
PF5411 - Single faucet drilling
PF5414 - 4” (102 mm) centers
20"
(508)
20"
(508)
4"
(102)
2-7/8"
(73)
9-3/4"
(289)
31"
(787)
Floor
16-3/8"
(716)
10-5/8"
(270)
5"
(127)
•
•
•
•
•
•
•
19” x 17” (483mm x 432mm) lavatory
4” (102mm) centers
Anti-splash rim
Concealed front overflow
Includes wall bracket
ADA compliant*
Available in white (WH) only
3/8"
(10)
11"
(279)
19"
(483)
Wall Bracket
19"
(483)
8"
(203)
4"
(102)
11-7/8"
(302)
3-1/4"
(89)
31"
(787)
11"
(279)
Floor
7-3/8"
(187)
15-1/8"
(384)
20-1/4"
(514)
6
3/8"
(10)
18-3/8”
(416)
PF5511 – Single faucet drilling
PF5514 – 4” (102mm) centers
PF5518 – 8” (203mm) centers
•
•
•
•
20” x 18” (508mm x 457mm) lavatory
High backsplash
Concealed front overflow
Concealed arm carrier connection
(not included)
• Includes wall bracket
• ADA compliant*
• Available in white (WH) only
PROFLO fixtures have a one-year limited warranty and meet or exceed the following standard: ASME A112.192;
IAPMO/cUPC listed; CSA approved. High efficiency toilets are LEED and LADWP compliant.
www.PROFLO.com
Countertop Lavatories
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
PF20171 - 1-hole in white only
PF20174 - 4” (102mm) centers
PF20178 - 8” (203mm) centers
• Vitreous china
• 20-1/2” x 17-1/2” (521mm x 445mm) outside
dimensions, self-rimming
• Concealed front overflow
• Can be mounted for ADA installation*
• Available in white (WH) and biscuit (BS)
8”
(203)
4”
(102)
3-1/16”
(78)
7-1/2”
(192)
17-1/2”
(445)
10-7/16”
(265)
15-7/8”
(403)
20-1/2”
(321)
FRONT EDGE
OF COUNTER TOP
8”
(203)
4”
(102)
PF19164- 4” (102mm) centers
PF19168 - 8” (203mm) centers (white only)
• Vitreous china
• 19” x 16” (483mm x 406mm) outside
dimensions, self-rimming
• Concealed front overflow
• Can be mounted for ADA installation*
• Available in white (WH) and biscuit (BS)
17-1/2”
(445)
2-1/2”
(64)
• Vitreous china
• 19-1/4” (488mm) outside dimension, round
self-rimming
• Concealed front overflow
• Can be mounted for ADA installation*
• Available in white (WH) and biscuit (BS)
3-1/32”
(77)
6-7/8”
(168)
WASTE
FINISHED FLOOR
FRONT EDGE
OF COUNTER TOP
8”
(203)
4”
(102)
18-31/32”
(482)
12-11/32”
(313)
CL
14-11/16”
(373)
19-1/4”
(488)
*All products listed as ADA compliant meet ADA requirements as stated in the American Disabilities Act when
installed in accordance with ADA guidelines.
7-7/8”
(201)
16-1/2”
(408) 34”
8”
(864)
(203)
10”
Max.
Min.
(254)
27”
(686)
CL
Min.
3/8”
(10)
15”
(381)
19”
(483)
PF191R - 1-hole in white only
PF194R - 4” (102mm) centers
PF198R - 8” (203mm) centers
1/2”
(13)
2”
(51)
WASTE
FINISHED FLOOR
7
Undercounter Lavatories
19-1/2"
(495mm)
1/2"
(13mm)
16-3/4"
(427mm)
ADA ROUGH-IN
3"
(76mm)
Counter Top
14"
(356mm)
8"
(203mm)
34"
(864mm)
17"
(432mm)
WASTE
29"
(737mm)
3-1/2"
(89mm)
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
PF1714U
•
•
•
•
•
•
•
Vitreous china
16-3/4”x 14” (427mm x 356mm) reveal
Concealed front overflow
Mounting clips included
Interior depth: 6-1/2” (165.1mm)
Can be mounted for ADA installation*
Available in white (WH) and biscuit (BS)
7-1/2"
(241mm)
3/4"
(19mm)
21-1/4”
(540 mm)
PF1915UWH
4” )
3/
1- mm
4
(4
• Vitreous china
• 19” x 15” (reveal)
• Oval undercounter lavatory
• Concealed front overflow
• Can be mounted for ADA installation
• Mounting clips included
• Available in white (WH) and biscuit (BS)
15-1/8”
(384 mm)
1-7/8”
(48 mm)
17-1/8”
(435 mm)
19”
(484 mm)
7-1/2”
(190 mm)
17"
(432mm)
1/2"
(13mm)
13 3/4"
(350mm)
ADA ROUGH-IN
3"
(76mm)
Counter Top
12"
(305mm)
8"
(203mm)
34"
(864mm)
15 3/8"
(390mm)
29"
(737mm)
WASTE
3 1/2"
(89mm)
PF1512U
•
•
•
•
•
•
•
Vitreous china
15-3/8” x 12” (390mm x 305mm) reveal
Concealed front overflow
Mounting clips included
Interior depth: 5-3/4” (146mm)
Can be mounted for ADA installation*
Available in white (WH) and biscuit (BS)
7 1/2"
(241mm)
1/2"
(13mm)
8
PROFLO fixtures have a one-year limited warranty and meet or exceed the following standard: ASME A112.192;
IAPMO/cUPC listed; CSA approved. High efficiency toilets are LEED and LADWP compliant.
www.PROFLO.com
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
Self-rimming
Drop-In Stainless Steel Sinks
Undercoated and padded for sound absorption
Sink Clips Included
Basket strainer sold separately
PFT151561
1-hole 6” (152mm) 22-guage
PFT151562
2-hole 6” (152mm) 22-guage
Drop-In stainless steel single bowl sink.
Overall Size: 15” x 15” (381mm x 381mm)
Bowl size: 12-1/4” x 10-1/2” (311mm x 267mm)
PFT172273
3-hole 7” (177mm) 22-guage
Drop-In stainless steel single bowl sink.
Overall Size: 17” x 22” (432mm x 559mm)
Bowl size: 14” x 15-3/4” (355mm x 399mm)
PFT171963
3-hole 6-1/8” (155mm) 22-guage
Drop-In stainless steel single bowl sink.
Overall Size: 17” x 19” (432mm x 482mm)
Bowl size: 14” x 14” (355mm x 355mm)
PFT171962
2-hole 6-1/8” (155mm) 22-guage
PFT2521553C
OS, 3-hole 5-1/2” (140mm) 22-guage
PFT2521553L
LH, 3-hole 5-1/2” (140mm) 22-guage
PFT2521553R
RH, 3-hole 5-1/2” (140mm) 22-guage
Drop-In stainless steel single bowl sink.
Overall Size: 25” x 21-1/4” (635mm x 540mm)
Bowl size: 21” x 15-3/4” (533mm x 400mm)
*All products listed as ADA compliant meet ADA requirements as stated in the American Disabilities Act when
installed in accordance with ADA guidelines.
9
Drop-In Stainless Steel Sinks
Self-rimming
Undercoated and padded for sound absorption
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
Sink Clips Included
Basket strainer sold separately
PFT252263 - 3-hole 6” (152mm) 22-gauge
PFT252264 - 4-hole 6” (152mm) 22-gauge
PFT252263BP - 3-hole 6” (152mm) 23-gauge 50 pack
PFT252264BP - 4-hole 6” (152mm) 23-gauge 50 pack
PFT2522653 - 3-hole 6.5” (165mm) 22-gauge
PFT2522654 - 4-hole 6.5” (165mm) 22-gauge
PFT252273 - 3-hole 7” (177mm ) 20-gauge
PFT252274 - 4-hole 7” (177mm ) 20-gauge
PFT252283 - 3-hole 8” (208mm ) 20-gauge
PFT252284 - 4-hole 8” (208mm ) 20-gauge
Drop-In stainless steel single bowl sink.
Overall size: 25” x 22” (635mm x 559mm)
Bowl size: 21-1/4” x 15-1/2” (540mm x 394mm)
PFT3321653
3-hole 6-1/2” (165mm) 22-guage
PFT3321654
4-hole 6-1/2” (165mm) 22-guage
Drop-In stainless steel double bowl sink.
Overall Size: 33” x 21-1/4” (838mm x 540mm)
Bowl size: 14” x 15-3/4” (355mm x 399mm)
PFT332263 - 3-hole 6” (152mm) 22-gauge
PFT332264 - 4-hole 6” (152mm) 22-gauge
PFT332263BP - 3-hole 6” (152mm) 23-gauge 50 packk
PFT332264BP - 4-hole 6” (152mm) 23-gauge 50 packk
PFT3322653 - 3-hole 6.5” (165mm) 22-gauge
PFT3322654 - 4-hole 6.5” (165mm) 22-gauge
PFT332273 - 3-hole 7” (177mm) 20-gauge
PFT332274 - 4-hole 7” (177mm) 20-gauge
PFT332283 - 3-hole 8” (208mm) 20-gauge
PFT332284 - 4-hole 8” (208mm) 20-gauge
Drop-In stainless steel double bowl sink.
Overall size: 33” x 22” (838mm x 559mm)
Bowl size: 14” x 16” (356mm x 406mm
10
PROFLO fixtures have a one-year limited warranty and meet or exceed the following standard: ASME A112.192;
IAPMO/cUPC listed; CSA approved. High efficiency toilets are LEED and LADWP compliant.
www.PROFLO.com
Dimensions may vary (+) or (-) 1/4”.
Floor and Laundry Sinks and Accessories
Numbers in () are mm.
PF906K 6-1/2”
(165)
8-5/8”
(219)
12”X12” (305mm x 305mm)
2” (50.8mm) NH connection
PF906M - 12”X12” (305mm x 305mm)
3” (76.2mm) NH connection
PF906P - 12”X12” (305mm x 305mm)
4” (101.6mm) NH connection
PF906B - floor sink basket
PFADS - Aluminum Dome Strainer
12”
(305)
6”
(152)
10”
12” (254)
(305)
9-3/8”
(238)
1-1/8”
(29)
9-1/4”
(235)
4-9/16”
(116)
9-3/8”
(238)
9-3/8”
(238)
1-3/8”
(35)
PF910 - Full top grate
PF912 - Half top grate
PF934 – Three-quarter top grate
PF912S - Split half top grate
9-3/8”
(238)
9-3/8”
(238)
9-1/4”
(235)
• White cast iron floor sink
12”
(305)
1-3/8”
(35)
4-9/16”
(116)
9-3/8”
(238)
• White porcelain top grate
9-3/8”
(238)
PF245
PF296
• Mop hanger for service sink
• Single hose bracket for service sink
• For use with service sink hose PFSSHE (see pg. 23)
11
Dimensions may vary (+) or (-) 1/4”.
Molded Basins and Receptors
PFLT4024 - Floor Mounted Double Compartment Sink
PFLT4024W - Wall Mounted Double Compartment Sink*
24"(610)
13/4"(44)
133/8"
(340)
137/8"
(352)
185/8"(473)
*Wall-mounting hardware and filler panels included
185/8"
(479)
9"
(229)
6"(152)
333/4"
(857)
40"
(1016)
203/8"
(518)
Numbers in () are mm.
11/4"(32)
4"
(102)
8"
(203)
23/8"(60)
Made from a Sheet Molding Compound (SMC), to create a laundry
tub with unparalleled strength. Floor-mounted units are equipped
with white baked enamel steel angle legs with leveling devices.
4” or 8” knock-out center set faucet holes.
PFLT2123 - Floor Mounted Multi-Purpose Sink
PFLT2123W - Wall Mounted Multi-Purpose Sink*
*Wall-mounting hardware and filler panels included
Made from a Sheet Molding Compound (SMC), to create a laundry
tub with unparalleled strength. Floor-mounted units are equipped
with white baked enamel steel angle legs with leveling devices.
4” knock-out center set faucet holes.
PFLT2522D - Drop-in Laundry Sink 24-1/2” x 22”
Self-rimming design. Made from a Sheet Molding Compound
(SMC), to create a laundry tub with unparalleled strength.
Available in white only. Drain size: 1-1/2”
Inside dimensions: 22-1/8” x 17” x 12-3/4”
PFLT2024 - Floor Mounted Multi-Purpose Sink
Single compartment, multi-purpose sink . Polypropylene
construction with integral strainer. Equipped with white baked
enamel steel angle legs with leveling devices.
4” or 8” knock-out center set faucet holes.
12
*All products listed as ADA compliant meet ADA requirements as stated in the American Disabilities Act when
installed in accordance with ADA guidelines.
www.PROFLO.com
Dimensions may vary (+) or (-) 1/4”.
Numbers in () are mm.
Molded Basins and Receptors
PFMB2424S - Mop Service Basin 24” X 24”
PFMB3624S - Mop Service Basin 24” X 36”
PFMB2424 - Mop Service Basin 24” X 24” with integral molded drain
PFBG24S - 24” Stainless Steel Bumper Guard
PFBG36S - 36” Stainless Steel Bumper Guard
PFBG24V - 24” Vinyl Bumper Guard
PFBG36V - 36” Vinyl Bumper Guard
PFWG24S - 24” Stainless Steel Wall Guard
PFWG36S - 36” Stainless Steel Wall Guard
PFMBQD - Pipe reducer for PVC Drain (3” to 2”)
Molded high density composite basin. Stainless Steel drain body.
Stainless steel dome strainer/lint basket.
36” model includes integrally molded, self-draining mop shelf.
Part #
Description
PFMBDRN
3” PVC Drain Assembly F/PFMB
PFMBSSDRN
3” SS Drain Assembly F/PFMB
PF245
Mop Hanger
PFSSHE
Service Hose
PF296
Service Hose Bracket
PFSB Series Shower Receptors
Molded high density composite basin.
PFSB3232WH - 32X32 Shower Floor with Strainer
PFSB3434WH - 34X34 Shower Floor with Strainer
PFSB3636NEOWH - 36X36 NEO Shower Floor with Strainer
PFSB3636WH - 36X36 Shower Floor with Strainer
PFSB4234WH - 42X34 Shower Floor with Strainer
PFSB4242WH - 42X42 Shower Floor with Strainer
PFSB4832WH - 48X32 Shower Floor with Strainer
PFSB4834WH - 48X34 Shower Floor with Strainer
PFSB5434WH - 54X34 Shower Floor with Strainer
PFSB6034WH - 60X34 Shower Floor with Strainer
PROFLO fixtures have a one-year limited warranty and meet or exceed the following standard: ASME A112.192;
IAPMO/cUPC listed; CSA approved. High efficiency toilets are LEED and LADWP compliant.
Part #
Description
PFSBSTR
Strainer F/PFSB Series White
PFSBGSKT
Gasket F/PFSB Series
13
Enameled Steel Tubs
PFB14R/L - Standard Rough in
PFB16R/L - Above Floor Rough in
Enameled steel bathtub. High gloss, stain resistant porcelain
finish. Foam bottom support pad.
PROFLO “S” Series Enameled Steel Tubs
PFB14RS/LS - Standard Rough in
PFB16RS/LS- Above Floor Rough in
Elastomer backing. Improved sound deadening, heat retention
and impact resistance.
PROFLO “S2” Series Enameled Steel Tubs
PFB14RS2/LS2 - Standard Rough in
PFB16RS2/LS2- Above Floor Rough in
High-density molded backing. Superior sound deadening, heat
retention and impact resistance.
14
www.PROFLO.com
Dimensions may vary (+) or (-) 1/4”.
Heavy Duty Commercial Faucets
Numbers in () are mm.
PFX100 - (with pop-up)
PFX101 - (without pop-up)
LOW
LEAD
COMPLIANT
• One piece cast brass body
• Ceramic cartridge with temperature limiting device
• 1.5 GPM water saving aerator
• Less pop-up
• Durable chrome finish
• Factory tested
PFX100 available in chrome (CP) and brushed nickel (BN)
PXF101 available in chrome (CP) only
Replacement cartridge available PFCF104CRT.
PFCF104 - (with pop-up)
PFCF104L - (without pop-up)
• One piece cast brass body
• Ceramic cartridge with temperature limiting device
• 1.5 GPM water saving aerator
• Metal pop-up
• Durable chrome finish
• Factory tested
• Available in chrome (CP) only
Replacement cartridge available PFCF104CRT.
PFCF110 - without pop-up
•
•
•
•
•
Gooseneck spout
Ceramic cartridge
Flexible stainless steel supplies
Factory tested
Available in chrome (CP) only
*All products listed as ADA compliant meet ADA requirements as stated in the American Disabilities Act when
installed in accordance with ADA guidelines.
15
Dimensions may vary (+) or (-) 1/4”.
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
Numbers in () are mm.
Lavatory Faucets
LOW
LEAD
5 5/8"
[143.00mm]
COMPLIANT
6 1/2"
[165.69mm]
with metal pop-up
without pop-up
•
•
•
•
•
•
•
•
•
•
6 1/2"
[164.92mm]
2 5/16"
[59.3mm]
1 1/2"
[38.54mm]
4 13/16"
[121.58mm]
1/2"-14NPSM
4"
[101.62mm]
PFWS4746CP
PFWS4744CP
Single-handle lavatory faucet
Ceramic disc cartridge
4” (102mm) centerset
Solid brass waterways
Polished chrome finish
1.5 gpm water-saving aerator
ADA compliant* lever handle
NSF/ANSI Std. 61 compliant
cUPC approved
Available in Brushed Nickel (BN)
LOW
LEAD
COMPLIANT
PFWS3016CP
•
•
•
•
•
•
•
•
Single-handle lavatory faucet w/ 50/50 pop-up
Ceramic disc cartridge
4” (102mm) centerset
1.5 gpm water-saving aerator
ADA compliant* lever handle
NSF/ANSI Std. 61 compliant
cUPC approved
Available in Brushed Nickel (BN)
LOW
LEAD
COMPLIANT
PFLL1012M
PFLL1002M
4-1/4”
(108)
3-1/8”
(79)
2”
(51)
4”
(102)
6-7/16”
(162)
12-5/16”
(313)
5-3/4”
(146)
2-7/16”
(60)
•
•
•
•
•
•
•
•
•
with grid drain PFWS1012M
less drain
PFWS1002M
Two-handle lavatory faucet; washerless design
4” (102mm) centerset
Solid brass waterways with metal housing
Polished chrome finish
2.0 gpm / WS 1.5 gpm water saving aerator
1/2” (12.7mm) MPT connections
ADA compliant* lever handle
NSF/ANSI Std. 61 compliant
cUPC approved
LOW
LEAD
COMPLIANT
4”
(102)
PFCF204
5O
1-5/8”
(42)
2-3/8”
(61)
1/2” - 14NPSM
4”
(102)
6-1/8”
(156)
16
4-1/4”
(108)
1/16”
(2)
to
1-1/2”
(38)
1/2” - 14NPSM
Coupling Nut
•
•
•
•
•
•
•
•
PFXCF204
Heavy-duty, two-handle lavatory faucet
4” (102mm) centerset, cast brass
Ceramic cartridge with brass stems
Polished chrome finish
2.0 gpm water saving aerator
Vandal-resistant screws and color-indexed caps
ADA compliant* wrist blade handles
Optional vandal resistant aerator PFCFVRMAER
PROFLO faucets carry a five-year limited warranty and meet or exceed the following standards:
ANSI: A112.18.1M. IAPMO/cUPC listed; CSA approved.
www.PROFLO.com
Lavatory Faucets
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
LOW
LEAD
COMPLIANT
7”
(177)
less pop-up PFWS1002ML
PFLL1012ML with metal pop-up PFWS1012ML
• Two-handle lavatory faucet
• 4” (102mm) centerset; durable chrome finish
• Washerless design and solid brass waterways with
metal housing
• 2.0 gpm water saving aerator
• ADA compliant* metal blade handles
• NSF/ANSI Std. 61 compliant
• cUPC approved
2-5/8”
(66.5)
1-7/16”
(36)
4-3/4”
(120.9)
2”
(50.8)
4”
(102)
6-5/16”
(160)
5-7/8”
(148.3)
Bar Faucets
LOW
LEAD
LOW
LEAD
COMPLIANT
PFCFB204
•
•
•
•
•
•
•
•
•
COMPLIANT
PFWS336M
PFXCFB204
•
•
•
•
•
•
•
•
•
•
Heavy-duty, two-handle bar faucet
4” (102mm) centerset, cast brass
Swivel gooseneck spout
Ceramic cartridge with brass stems
Polished chrome finish
2.0 gpm water saving aerator
Vandal-resistant screws and color-indexed caps
ADA compliant* wrist blade handles
Optional vandal resistant aerator PFCFVRAER
Two-handle bar faucet
Washerless design
Solid brass waterways
Polished chrome finish
4” (102mm) centerset
9 3/8” (238mm) spout
2.0 gpm water saving aerator
1/2” (12.7mm) MPT connections
ADA compliant* metal wing handles
cUPC approved
9-3/8”
(237.24)
12-15/16”
(312)
3-9/16”
(90.93)
6-13/16”
(172.21)
4”
(102)
7-1/2”
(190)
5-1/2”
(139.19)
2-3/8”
(61)
4”
(102)
5-15/16”
(151)
1/16”
(2)
to
1-1/2”
(38)
1/2” 14NPSM
1/2” 14NPSM
Coupling Nut
4-7/16”
(112)
*All products listed as ADA compliant meet ADA requirements as stated in the American Disabilities Act when
installed in accordance with ADA guidelines.
5/8”
(16.51)
2”
(50.55)
4”
(102)
6”
(152)
12-1/4”
(311.66)
4-3/4”
(12.5)
2-1/4”
(57)
17
Kitchen Faucets
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
LOW
LEAD
LOW
LEAD
COMPLIANT
PFCF208 4” spout
PFCF218 8” spout
•
•
•
•
•
•
•
•
•
COMPLIANT
PFCFU208
PFCFU218
PFXCF208
•
•
•
•
•
•
•
•
•
Heavy-duty, two-handle faucet
8” (203mm) centerset, cast brass
Ceramic cartridge with brass stems
Polished chrome finish
2.0 gpm water saving aerator
Vandal-resistant screws and color-indexed caps
ADA compliant* wrist blade handles
Optional vandal resistant aerator PFCFVRAER
cUPC approved
4” spout
8” spout
Heavy-duty, two-handle faucet
6 - 12” (152.4 - 304.8mm) undermount, cast brass
Ceramic cartridge with brass stems
Polished chrome finish
2.0 gpm water saving aerator
Vandal-resistant screws and color-indexed caps
ADA compliant* wrist blade handles
Optional vandal resistant aerator PFCFVRAER
cUPC approved
12-1/16”
(307)
12-15/16”
(312)
4”
(102)
4”
(102)
7-1/2”
(190)
2-3/8”
(61)
9”
(203)
9-15/16”
(253)
1/16”
(2)
to
1-1/2”
(38)
Single-handle kitchen faucet
Ceramic disc cartridge
8” (203mm) centerset
1.5 gpm water saving aerator
ADA compliant* metal lever handle
NSF/ANSI Std. 61 compliant
cUPC approved
Available in chrome and brushed nickel finishes
3-1/8”
(80)
1/16”
(2)
to
1-1/2”
(38)
1/2” 14NPSM
Coupling Nut
1/2” 14NPSM
1/2” 14NPSM
Coupling Nut
4-7/16”
(112)
4-7/16”
(112)
PFX2021M
PFXC3121CP - Black side spray on deck
PFXC4121CP - Color match side spray on deck
PFXC4121BN - Color match side sprayy on deck
LOW
LEAD
COMPLIANT
18
7-1/4”
(185)
1/2” 14NPSM
PFXC4111
•
•
•
•
•
•
•
•
PFXCFU208
•
•
•
•
•
•
•
•
Single-handle kitchen faucet
With spray on deck; 8” (203mm) centerset
seet
Ceramic disc design; copper waterways
1.5 gpm water saving aerator
1/2” (12.7mm) MPT connections
ADA compliant* metal lever handle
NSF/ANSI Std. 61 compliant
LOW
OW
W
LEAD
AD
D
cUPC approved
COMPLIANT
PLIANT
PROFLO faucets carry a five-year limited warranty and meet or exceed the following standards:
ANSI: A112.18.1M. IAPMO/cUPC listed; CSA approved.
www.PROFLO.com
Kitchen Faucets
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
10 1/8"
[256.40mm]
9 5/8"
[243.87mm]
8 1/16"
[204.00mm]
2 3/16"
[55.39mm]
LOW
LEAD
COMPLIANT
1/2"-14NPSM
8"
[203.20mm]
PFXC5150
P
• Chrome single-handle kitchen faucet w/
pull-out spray
• Internal vacuum breaker construction
• Ceramic disc cartridge
• Flexible connectors
• 1.5 gpm water-saving aerator
• ADA compliant* lever handle
• CSA approved
• NSF/ANSI Std. 61 compliant
• Available in chrome, brushed nickel
and oil rubbed bronze finishes
6"
[152.13mm]
7 7/16"
Single-handle kitchen faucet
Ceramic disc cartridge
8” (203mm) centerset
1.5 gpm water saving aerator
ADA compliant* metal lever handle
CSA approved
NSF/ANSI Std. 61 compliant
[189.06mm]
PFXC3101CP - Chrome
P
•
•
•
•
•
•
•
7-1/2”
(190.5)
8-3/8”
(212.7)
3-1/2”
(889)
12.6”
COLD
(320)
14.1”
HOT
(368)
4”
(101.6)
LOW
LEAD
8”
(203.2)
COMPLIANT
8-1/8”
(206.3)
2-1/4”
(57.1)
10-3/8”
(263.5)
Service Faucets
PF418
PF418
P
7 13/16
7 13/16”
(198.1mm)
• Rough brass body
• 3-3/8” (86mm) centerset; combination union inlet
1/2” (12.7mm) threaded or solder
• Polished chrome finish
• Solid brass waterways; renewable seats and stems; CP brass body
• ADA compliant* lever handles
(198.1mm)
7-13/16”
(198.1)
23-3/8”
(596)
15-3/8”
(385.6)
2-15/16”
(75)
1-3/16”
(30.2)
1/2” - 14NPT
(12.7)
2”
(51)
1/4
¿ 1/4
(6.1mm)
(6.1mm)
3-3/8”
(86)
4-1/8”
(105.6)
7-1/4”
(184)
*All products listed as ADA compliant meet ADA requirements as stated in the American Disabilities Act when
installed in accordance with ADA guidelines.
2-7/16”
(62.5)
8-23/32”
(221.1)
7/8”
(23)
19
Service Faucets
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
LOW
LEAD
4-1/8”
(104.5)
2-1/2”
(63)
COMPLIANT
PF800
PFX800
2-7/8”
(73)
• Swing spout
• Adjustable center 7” to 9” (178 to 229mm), solid
brass waterways; renewable seats and stems
• Polished chrome finish
• 6” (152mm) cast brass spout w/
water-saving aerator
• ADA compliant* lever handles
4”
(101.6)
8”
(203.2)
11”
(279)
5-1/2”
(139.7)
2-3/4”
(69.9)
8-1/2”
(215)
5”
(127)
3-3/8”
(85.7)
5-7/8”
(149)
3-7/8”
(98)
LOW
LEAD
COMPLIANT
2-3/4” 1-13/16”
(70)
(46)
8”
(202)
12-3/8”
(314)
PF80012
PF800U
13-11/16”
(347)
•
•
•
•
•
12” (304.8mm) spout PFX80012
6” (152.4mm) spout PFX800U
8” (203.2mm) centers
Polished chrome finish
Cast brass spout; water-saving aerator
Soap dish
ADA compliant* lever handles
2”
(50.05)
4-7/8”
(124)
1-15/16”
(48.51)
1-1/2”
(37.59)
PF244
15/16”
(23.88)
7-1/8”
(180.09)
1-5/8”
(40.89)
• Laundry faucet
• Rough brass body w/ 3-3/8” (85.7mm) centers
• Clamp-type mounting; solid brass body and
waterways; renewable seats and stems
• Polished chrome handles
• ADA compliant* lever handles
1/4”
(5.59)
2-15/16”
(74.93)
3-3/8”
(85.7)
7”
(128)
1-3/8”
(35.31)
3/4”
(19.3)
8-1/2”
(126)
7.62”
(194)
4-11/16”
(119)
LOW
LEAD
2”
(51)
3-21/64”
(846)
COMPLIANT
PFX7002A - acrylic handles
PFX7002M - metal lever handles
3-1/4”
(826)
2-5/32”
(55)
4”
(102)
6-1/8”
(156)
20
8-1/2”
(216)
•
•
•
•
•
•
4” (102mm) centerset
8” (203.2mm) spout with washerless design
Aerator or hose thread connection
Polished chrome finish
NSF/ANSI Std. 61 compliant
cUPC approved
PROFLO faucets carry a five-year limited warranty and meet or exceed the following standards:
ANSI: A112.18.1M. IAPMO/cUPC listed.
www.PROFLO.com
Service Faucets
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
1-1/2”
(38.1)
PF1118
•
•
•
•
•
3/4” (19mm) ho
hose thread on spout
With wall base, vacuum breaker, integral stops
Solid brass waterways;
wat
renewable seats and stems
Chrome finish
CUPC / ASSE aapproval
Ref.
8-3/4”
(222.25)
4-7/8”
(124)
8”
(203.2)
3/4 - 11-1/2 NH-2A
(19)
11”
(280)
Ref.
9”
(228.6)
Ref.
9-13/16”
(254)
1/2” NPT
(12.7)
2-3/4”
(70)
4-5/8”
(117)
LOW
LEAD
6-7/8”
(174)
2-1/2”
(63)
COMPLIANT
PF750
•
•
•
•
PFX750
Chrome-pla
Chrome-plated brass finish
Heavy duty
Self-closing basin
Solid brass waterways; renewable seats and stems
2”
(50.8)
3-1/2”
(89)
4-7/8”
(124)
2”
(51)
2-3/4”
(69)
5-1/4”
(133.4)
2-1/8”
(54)
PF300
•
•
•
•
Chrome-pla brass finish
Chrome-plated
Includes ho
hot and cold index buttons
1/2” (12.7m
(12.7mm) single base
Solid brass waterways; renewable seats and stems
1/2”
(14NPS)
2”
(51)
3-3/8”
(85)
4-13/16”
(122)
21
Bath and Shower Accessories
•
•
•
•
•
•
22
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
PF14BSBN - brushed nickel
PF14BSCP - chrome
PF14510CP - chrome plated
PF14510BN - brushed nickel
• Slide bar with 7/8” (22.2mm) brass bar
• 22-1/2” (572mm) slide bar for adjustable
handshower (handshower not included)
• Handshower slides up and down bar to
customize spray height
• Use with handshower kits PF14510,
P
PF14310, PF14110
• S
Screws and anchors included
• AD
ADA compliant*
• Adjustable spray hand-held shower
• Five functions - drenching combination massage,
heavy and light sprays
• Flexclean™ eliminates clogging and corrosion
• Includes handshower mounting hardware, 60”
(1524mm) Meraflex II™ hose
• 1.75 gpm
• ADA compliant*
PF14110WH - white
• Heavy spray hand-held shower
• Flexclean™ eliminates clogging and corrosion
• Includes handshower mounting hardware, 60”
(1524mm) vinyl hose
• 1.75 gpm
• ADA compliant*
PF14310CP - chrome plated
1-3/4” (38mm) stainless steel grab bar
18-gauge 304 stainless steel bar
14-gauge 304 stainless steel flange
#10 x 2” (50.8mm) self-tapping stainless steel screws
Must be attached to wall stud
ADA compliant*
•
•
•
•
Adjustable spray hand-held shower
Three functions - massage, heavy and light sprays
Flexclean™ eliminates clogging and corrosion
Includes handshower mounting hardware, 60”
(1524mm) Meraflex II™ hose
• 1.75 gpm
• ADA compliant*
PFSCR60 - 5ft. (1524mm) - chrome
PFSCR72 - 6ft. (1829mm) - chrome
PFSRFCP - flange kit
• Straight shower rod
• Made of aluminum
• Shower rod flange kit sold separately
Satin Finish
Peened Finish
Length
PFGB12SF
PFGB12PF
12” (304.8mm)
PFGB16SF
PFGB16PF
16” (406.4mm)
PFGB18SF
PFGB18PF
18” (457.2mm)
PFGB24SF
PFGB24PF
24” (609.6mm)
PFGB30SF
PFGB30PF
30” (762mm)
PFGB32SF
PFGB32PF
32” (812.8mm)
PFGB36SF
PFGB36PF
36” (914.4mm)
PFGB42SF
PFGB42PF
42” (1066.8mm)
mm) shower
• Curved shower rod fits 5 ft. (1524mm)
ded for installation into
• Flange kit included: hardware included
sheetrock, tile and wood
% more shower area)
• Adds 9” (229mm) elbow room (25%
• Fits all standard shower curtains
eel
• Made of 22-gauge 445 stainless steel
PFGB48SF
PFGB48PF
48” (1219.2mm)
PFCSRFLG - Replacement flange kit
PFCSRH60CP - chrome plated
PFCSRH60BN - brushed nickel
*All products listed as ADA compliant meet ADA requirements as stated in the American Disabilities Act when
installed in accordance with ADA guidelines.
www.PROFLO.com
Access Doors
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
PF88SSAD - 8” x 8” (203.2mm x 203.2mm) stainless steel universal access door
PF1010SSAD - 10” x 10” (254mm x 254mm) stainless steel universal access door
PF1212SSAD - 12” x 12” (304.8mm x 304.8mm) stainless steel universal access door
PF88AD - 8” x 8” (203.2mm x 203.2mm) steel universal access door, white
PF1010AD - 10” x 10” (254mm x 254mm) steel universal access door, white
PF1212AD - 12” x 12” (304.8mm x 304.8mm) steel universal access door, white
PF1414AD - 14” x 14” (355.6mm x 355.6mm) steel universal access door, white
PF1616AD - 16” x 16” (406.4mm x 406.4mm) steel universal access door, white
PF1818AD - 18” x 18” (457.2mm x 457.2mm) steel universal access door, white
PF2424AD - 24” x 24” (609.6mm x 609.6mm) steel universal access door, white
•
•
•
•
One-piece construction
Concealed pivoting rod hinge
16-gauge stainless steel or prime-coat finished steel
Not approved for fire rated applications
Sink and Drain Accessories
PFSSHE
PFPTB502 – 1-1/2” x 1-1/2”
• Service sink hose
• 5/8” x 30” (15.9mm x 762mm)
• 3/4” (19mm) hose thread connection
PFPTB503 – 1-1/2” x 1-1/2”
(38.1mm x 38.1mm)
Includes 1-1/4” x 1-1/2” (31.8mm x 38.1mm) washer
(38.1mm x 38.1mm) w/o cleanout
PFPTB400 - 1-1/2” x 1-1/4” (38.1mm x 31.8mm)
PFPTB401 - 1-1/4” x 1-1/2” (31.8mm x 38.1mm)
PFPTB403 - 1-1/4” x 1-1/4” (31.8mm x 31.8mm)
PFPTB402 - 1-1/4” x 1-1/2” (31.8mm x 38.1mm)
PFPTB500 – 1-1/4” x 1-1/2” (31.8mm x 38.1mm)
PFPTB501 - 1-1/4” x 1-1/2” (31.8mm x 38.1mm)
• Polished chrome cast brass
• 17-gauge wall bend and deep escutcheon
• Solid brass nuts w/cleanout
w/o cleanout
•
•
•
•
•
Chrome-plated finish
Cast brass
Ground joint swivel
Solid brass nuts with clean out
17-gauge
PFOD100
PF151CP
51CP
1CP
PFWTS
W
WTS
• 1-1/2” (38.1mm) offset tail piece for sink
• 17-gauge
• Heavy duty
• Chrome-plated finish
• 3-1/2” (88.9mm) premium basket strainer
• Forged heavy brass body
•
•
•
•
Stainless steel
Flat top strainer
Chrome-plated body
Grid fits 3-1/2” (88.9mm) opening
23
Sink and Drain Accessories
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
PF002 - 2” (50.8mm) IPS outlet
PF003 - 3” (76.2mm) IPS outlet
• Cast Iron trap with chrome-plated strainer for
service sinks
PFGD100
•
•
•
•
•
PFSCPTWH - white
PFSCPTBK - black
PFSCPT1SWH - white
PFSCPT1SBK - black
• One p-trap cover- soft
• One p-trap cover, one valve and
supply cover- soft
PFSCPT2SOFFWH - white
PFSCPT2SOFFBK - black
PFSC1SWH - white
PFSC1SBK - black
• One p-trap cover, two valve and
supply covers, one 5” (127mm)
offset tailpiece wheelchair strainer
cover- soft
• One valve and supply cover- soft
PFSCOFFWH - white
PFSCOFFBK - black
PFSCPT2SWH - white
PFSCPT2SBK - black
• 5” (127mm) offset tailpiece
wheelchair strainer cover- soft
• One p-trap cover, two valve and
supply covers - soft
Heavy-duty grid drain
1-1/4” x 6” (31.8mm x 152.4mm) w/ overflow
Chrome-plated finish
Cast brass construction with 17-gauge tailpiece
CUPC approval
PFGD101
•
•
•
•
Heavy-duty wheelchair accessible lavatory elbow
Chrome-plated finish
Cast brass construction with 17-gauge tailpiece
cUPC approval
PF200WH
• One p-trap cover - molded
PF299WH
• One angle valve, one 12” (304.8mm)
supply cover - molded
PFEXT200WH
• One 16” (406.4mm) extension for
drain waste arm or tailpiece - molded
PF201WH
• One p-trap cover, one angle valve, one 12”
(304.8mm) supply cover - molded
PF202WH
• White three-piece p-trap and supply
covers - molded
PF203WH
• One p-trap cover, two angle valve covers, two 12”
(304.8mm) supply covers, one 5” (127mm) offset
tailpiece, wheelchair strainer cover
PF205WH
•
•
•
•
•
•
Quick, easy installation with Velcro
Universal design fits virtually all p-trap assemblies
Over 360 degree flexibility
Smooth, high-gloss finish with UV
Optional reusable non-abrasive snap fasteners offer extra tamper resistance
PVC insulation is Class A Fire Rated and meets ASTM E84 with a 25 flame and 450
smoke rating
• ADA, IBC, ICC/ANSI and Canada-Barrier Free compliant
• Offset tailpiece cover, white - molded
24
*All products listed as ADA compliant meet ADA requirements as stated in the American Disabilities Act when
installed in accordance with ADA guidelines.
www.PROFLO.com
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
Trap Primers and Accessories
PFTRAPID
PFTRAPSD
PFPDUU
PFP1500
PF127033
• 1/2” (12.7mm)
IPS with auto
vacuum breaker,
bronze
• 1/2” (12.7mm) sweat
with auto vacuum
breaker, bronze
• 4 opening
distribution unit
without fitting,
plastic body
• 1/2” (12.7mm) auto
trap primer valve
• Will prime 1 or 4 floor
drains
• 1-1/4” (31.8mm)
semi-cast brass
tailpiece
PFP2500
• 1/2” (12.7mm) auto
trap primer valve
• Will prime 1 or 2
floor drains
• No adjustment
required
PF127044
• 1-1/2” (38.1mm)
semi-cast brass
tailpiece
Lavatory Supply Kits
LEAD FREE CODE
PFCATT22CLKRL12 - 3/8” IPS X 3/8” IPS rigid kit loose key
PFCAT22CL12 - 3/8” IPS X 3/8” OD flex kit round wheel
PFCATT22CLKL12 - 3/8” IPS X 3/8” OD flex kit loose key
PFCAC32CL12 - 5/8” OD X 3/8” OD flex kit round wheel
PFCAC32CLKL12 - 5/8” OD COMP X 3/8” OD flex kit loose key
PFCAS32CL12 - 1/2” SWT X 3/8” OD flex kit round wheel
PFCAS32CLKL12 - 1/2” SWT X 3/8” OD flex kit loose key
PFCAZ32CL12 - 1/2” SWT W/EXT 3/8” OD flex kit round wheel
PFCAZ32CLKL12 - 1/2” SWT W/EXT 3/8” OD flex kit loose key
PFCAT32CL12 - 1/2” IPS X 3/8” OD flex kit round wheel
PFCAT32CLKL12 - 1/2” IPS X 3/8” OD flex kit loose key
PFCAT33CL12 - 1/2” IPS X 1/2” OD flex kit round wheel
N/A
N/A
N/A
N/A
PFXCAC32CLKL12
N/A
N/A
N/A
N/A
N/A
N/A
N/A
• Includes flexible chrome-plated copper risers with chrome-plated steel deep flanges
and chrome-plated stops
• Stops are solid brass construction with round wheel handle or loose key as noted
• NSF/ANSI Std. 61 compliant
• Available only in pairs
• CSA approved
25
Closet Supply Kits
PFCAT22CC12 - 3/8” IPS X 3/8” OD flex closet supply kit round wheel
PFCAT22CLKC12 - 3/8” IPS X 3/8” OD flex closet supply kit loose key
PFCAC32CC12 - 5/8” OD X 3/8” OD flex closet supply kit round wheel
PFCAC32CLKC12 - 5/8” OD X 3/8” OD flex closet supply kit loose key
PFCAS32CC12 - 1/2” SWT X 3/8” OD flex closet supply kit round wheel
PFCAS32CLKC12 - 1/2” SWT X 3/8” OD flex closet supply kit loose key
PFCAZ32CC12 - 1/2” SWT w/ EXT X 3/8” OD flex closet angle supply kit
• Includes flexible chrome-plated copper risers with chrome-plated steel deep flanges and chrome-plated stops
• Stops are solid brass construction with round wheel handle or loose key as noted
• NSF/ANSI Std. 61 compliant
Heavy Pattern Supply Kits
PFHATT22CLKL12 - 3/8” IPS X 3/8” OD comm flex lav supply kit loose key
PFHAT32CL12 - 1/2” IPS X 3/8” OD comm flex lav supply kit
PFHAT32CLKL12 - 1/2” IPS X 3/8” OD comm flex lav supply kit loose key
PFHAT33CLKL12 - 1/2” IPS X 1/2” OD comm flex lav supply kit loose key
• Lavatory kit includes flexible chrome-plated copper or rigid risers with chrome-plated steel deep
flanges and chrome-plated stops
• Stops are solid brass construction with round wheel handle or loose key as noted
• NSF/ANSI Std. 61 compliant
• Available only in pairs
PFHAT32CC12
- 1/2” IPS X 3/8” OD flex closet supply kit round wheel
ADA Lavatory Supply Kit
PFCSTT22CLKWHRL6 - 3/8” IPS X 3/8” IPS wheelchair kit loose key
• Stops are solid brass construction with round wheel handle or loose key as noted
• NSF/ANSI Std. 61 compliant
26
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
www.PROFLO.com
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
Individual Stops
LEAD FREE CODE
PFCATT22CLK - 3/8” IPS X 3/8” IPS angle stop loose key
PFCAT22C - 3/8” IPS X 3/8” OD angle stop round wheel
PFCAT22CLK - 3/8” IPS X 3/8” OD angle stop loose key
PFCATT33CLK - 1/2” IPS X 1/2” IPS angle stop loose key
PFCAT32C - 1/2” IPS X 3/8” OD angle stop round wheel
PFCAT32CLK - 1/2” IPS X 3/8” OD angle stop loose key
PFCAT33C - 1/2” IPS X 1/2” OD angle stop round wheel
PFCAC32C - 5/8” OD X 3/8” OD angle stop round wheel
PFCAC32CLK - 5/8” OD X 3/8” OD angle stop loose key
PFCAS32C - 1/2” SWT X 3/8” OD angle stop round wheel
PFCAS32CLK - 1/2” SWT X 3/8” OD angle stop loose key
PFCAZ32C - 1/2” SWT W/EXT X 3/8” OD angle stop round wheel
PFCAZ32CLK - 1/2” SWT W/EXT X 3/8” OD angle stop loose key
N/A
N/A
N/A
N/A
PFXCAT32C
PFXCAT32CLK
PFXCAT33C
PFXCAC32C
N/A
N/A
N/A
N/A
N/A
• Solid brass construction and chrome-plated with round wheel handle or loose key as noted
• NSF/ANSI Std. 61 compliant
Heavy Individual Stops
PFHAT32C - 1/2” IPS X 3/8” OD angle stop round wheel
PFHAT32CLK - 1/2” IPS X 3/8” OD angle stop loose key
PFHAT33CLK - 1/2” IPS X 1/2” OD angle stop loose key
PFHAC32CLK - 5/8” OD X 3/8” OD angle stop loose key
• Solid brass construction and chrome-plated with round wheel handle or loose key as noted
• NSF/ANSI Std. 61 compliant
27
Water Hammer Arrestors
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
FNWSWA500 - copper sweat 1/2” (12.7mm)
FNWSWA750 - copper sweat 3/4” (19mm)
FNWSWA1000 - copper sweat 1” (25.4mm)
FNWSWA1250 - copper sweat 1-1/4” (31.8mm)
FNWSC500 - male NPT 1/2” (12.7mm)
FNWSC750 - male NPT 3/4” (19mm)
FNWSC1000 - male NPT 1” (25.4mm)
FNWSC1250 - male NPT 1-1/4” (31.8mm)
FNWSC1500 - male NPT 1-1/2” (38.1mm)
FNWSC2000 - male NPT 2” (50.8mm)
•
•
•
•
•
•
•
•
28
LEAD FREE CODES
FNWXSC500
FNWXSC750
FNWXSC1000
FNWXSC1250
FNWXSC1500
FNWXSC2000
Max. pressure: 600 PSI
Working pressure: 60 to 400 PSI
Temperature: - 33°F to 180°F (0.6°C to 86.7°C)
Low lead brass
Vertical or horizontal installation
Can be installed in systems without need for access panels
ASSE 1010-2004 listed
cIAMPO listed (cUPC)
www.PROFLO.com
Dimensions may vary (+) or (-) 1/4”. Numbers in () are mm.
No-Hub Couplings
PFNHCJ - 1-1/2” (38.1mm) standard duty
PFNHCK - 2” (50.8mm) standard duty
PFNHCM - 3” (76.2mm) standard duty
PFNHCP - 4” (101.6mm) standard duty
PFNHCS - 5” (127mm) standard duty
PFNHCU - 6” (152.4mm) standard duty
PFNHCX - 8” (203.2mm) standard duty
PFNHC10 - 10” (254mm) standard duty
PFNHRCKJ - 2” X 1-1/2” (50.8mm x 38.1mm) reducing
PFNHRCMK - 3” X 2” (76.2mm x 50.8mm) reducing
PFNHRCPM - 4” X 3” (101.6mm x 76.2mm) reducing
• 1/2” (12.7mm) and 9/16” (14.3mm) band widths with 5/16” (7.9mm) hex-head screw
applies 60 in.-lbs. of installation torque to the band/shield assembly
• NSF Compiiant
PFNHHMDCJ - 1-1/2” (38.1mm) medium duty, yellow w/ 5/16” (7.9mm) screw
PFNHHMDCK - 2” (50.8mm) medium duty, yellow w/ 5/16” (7.9mm) screw
PFNHHMDCM - 3” (76.2mm) medium duty, yellow w/ 5/16” (7.9mm) screw
PFNHHMDCP - 4” (101.6mm) medium duty, yellow w/ 5/16” (7.9mm) screw
PFNHHMDCS - 5” (127mm) medium duty, yellow w/ 5/16” (7.9mm) screw
PFNHHMDCU - 6” (152.4mm) medium duty, yellow w/ 5/16” (7.9mm) screw
PFNHHMDCX - 8” (203.2mm) medium duty, yellow w/ 5/16” (7.9mm) screw
PFNHHMDC10 - 10” (254mm) medium duty, yellow w/ 5/16” (7.9mm) screw
• 5/16” (7.9mm) hex-head screw is designed to apply the full load of 80 in.-lbs. of
installation torque to the band/shield assembly
• CSA approved
PFNHHHDCJ - 1-1/2” (38.1mm) heavy duty, green w/ 3/8” (9.5mm) screw
PFNHHHDCK - 2” (50.8mm) heavy duty, green w/ 3/8” (9.5mm) screw
PFNHHHDCM - 3” (76.2mm) heavy duty, green w/ 3/8” (9.5mm) screw
PFNHHHDCP - 4” (101.6mm) heavy duty, green w/ 3/8” (9.5mm) screw
PFNHHHDCS - 5” (127mm) heavy duty, green w/ 3/8” (9.5mm) screw
PFNHHHDCU - 6” (152.4mm) heavy duty, green w/ 3/8” (9.5mm) screw
PFNHHHDCX - 8” (203.2mm) heavy duty, green w/ 3/8” (9.5mm) screw
PFNHHHDC10 - 10” (254mm) heavy duty, green w/ 3/8” (9.5mm) screw
PFNHWBC12 - 12” (304.8mm) heavy duty, green w/ 3/8” (9.5mm) screw
PFNHWBC15 - 15” (381mm) heavy duty, green w/ 3/8” (9.5mm) screw
• 3/8” (9.5mm) hex head screw is designed to apply the full load of 80 in.-lbs. of
installation torque to the band/shield assembly
• CSA approved
Conforms to CISPI 310 and comply with ASTM, C564, ASTM C1277, IAMPO file #3198,
Commonwealth of Massachusetts CMR-248 and City of New York MEA 253-98-E. Gaskets are
made from an elastomeric compound that meets the requirements of ASTM C564.
29
®
For more information on PROFLO products
PROFLO.com
Green Solutions
© 2012 Ferguson Enterprises, Inc. All Rights Reserved
PL PF-200 13009 08/12

Similar documents

Atlantis

Atlantis lever (fluidmaster ballcock) (styrofoam lined) 5061-XXX-5254 Low profile tank with chrome plated trim lever (fluidmaster ballcock) (styrofoam lined) 05-XXX-001 toilet seat (with metal hinges) 05-XX...

More information