1. Barracuda Spam Firewall - Overview

Transcription

1. Barracuda Spam Firewall - Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 Deployment Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.1 Deployment in the DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.2 Deployment Behind the Corporate Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.3 Clustering the Barracuda Spam Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.3.1 Benefits of Clustering the Barracuda Spam Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.3.2 How to Cluster the Barracuda Spam Firewall 7.x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.4 Virtual Deployment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.4.1 How to Deploy Barracuda Spam Firewall Vx Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.4.2 Allocating Cores, RAM, and Hard Disk Space for Your Barracuda Spam Firewall Vx . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.4.3 Barracuda Spam Firewall Vx Quick Start Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.4.4 Route Email to the Barracuda Spam Firewall Vx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.4.5 Backing Up Your Virtual Machine System State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.5 Public Cloud Hosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.5.1 Amazon Web Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.5.1.1 How to Deploy the Barracuda Spam Firewall on Amazon Web Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.5.2 Microsoft Azure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.5.2.1 How to Deploy the Barracuda Spam Firewall on Microsoft Azure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.5.2.2 Barracuda Spam Firewall Quick Start Guide on Microsoft Azure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.5.2.3 How to add Additional Storage to your Azure Deployment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.5.3 VMware vCloud Air Deployment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.5.3.1 How to Deploy the Barracuda Spam Firewall in VMware vCloud Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.5.3.2 Barracuda Spam Firewall Quick Start Guide on vCloud Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.1 Step 1 - Understand the Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.2 Step 2 - Install the Barracuda Spam Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.3 Step 3 - Initial Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.4 Step 4 - Product Activation and Firmware Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.5 Step 5 - Configure the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.5.1 How to Enable SSL for Administrators and Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.6 Step 6 - Routing Inbound Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.6.1 Using MX Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.7 How to Tune and Monitor the Default Spam and Virus Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.7.1 How to Get and Configure Barracuda Exchange Antivirus Agent 7.1 and Above . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.7.2 How to Get and Configure the Barracuda Exchange Antivirus Agent 6.0.x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.7.3 Virus Checking and Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.7.4 How Spam Scoring Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.7.5 Monitoring Inbound and Outbound Email Traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.7.6 Performance and Email Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.8 Quarantine: An Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.9 Mail Journaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.10 How to Migrate From Postini to the Barracuda Spam Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4 Routing Outbound Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4.1 About Scanning of Outbound Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4.2 How to Route Outbound Mail from the Barracuda Spam Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4.3 How to Configure Office 365 for Inbound and Outbound Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4.4 How to Configure Google Apps for Inbound and Outbound Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4.5 How to Route Outbound Mail from Kerio Connect Mail Server through the Barracuda Spam Firewall . . . . . . . . . . . . . . . . .
1.4.6 Encryption of Outbound Mail 6 and Above . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4.6.1 How to Use DLP and Encryption of Outbound Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4.6.1.1 Medical Dictionary Source for DLP HIPAA Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4.6.2 How to Use DLP Filters With Spreadsheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4.6.3 Archiving Encrypted Email Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4.7 Encryption of Outbound Mail 5.x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5 Securing the Barracuda Spam Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5.1 Cloud-Based Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5.2 How to Set Up Your Cloud Protection Layer (CPL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6 Advanced Spam Filtering Inbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6.1 Rate Control Inbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6.2 IP Analysis Inbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6.3 Content Analysis Inbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6.4 Bayesian Analysis Inbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
4
21
22
23
24
25
27
29
32
35
36
39
41
44
45
46
47
48
60
63
66
69
72
73
80
81
82
86
87
90
91
92
93
94
97
98
101
103
104
105
106
107
108
109
110
111
112
114
120
122
123
126
128
129
130
131
134
136
137
140
141
142
144
146
1.7 Advanced Spam Filtering Outbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.7.1 Spam Scoring Outbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.7.2 Rate Control Outbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.7.3 IP Analysis Outbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.7.4 Sender and Recipient Filtering Outbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.7.5 Reverse DNS Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.7.6 Content Analysis Outbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.7.7 Attachment Filtering Outbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.7.8 Bayesian Analysis Outbound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.8 Advanced Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.8.1 Sender Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.8.2 Recipient Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.8.3 Remote IMAP/POP Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.8.4 Advanced Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.8.5 Non-Delivery Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.8.6 Remote Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.9 Creating and Managing Domains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.10 Managing Inbound Quarantine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.10.1 How Quarantine of Inbound Mail Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.10.2 Quarantine Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.10.3 Controlling Access to Account Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.10.4 How Quarantine Notifications Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.10.5 Retention Policy and Purging Old Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.11 Managing Outbound Quarantine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.12 Creating and Managing Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.12.1 Role-based Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.12.1.1 Roles and Navigating the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.12.1.2 Role Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.12.1.2.1 Domain Admin Role . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.12.1.2.2 Helpdesk Role . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.12.1.2.3 User Role . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.12.1.2.4 Governance, Risk Management and Compliance (GRC) Account Role . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.13 Monitoring the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.13.1 Basic Monitoring Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.13.2 Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.13.3 How to Set Up Alerts and SNMP Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.13.3.1 How to Use SNMP Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.13.3.2 Barracuda Spam Firewall SNMP MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.13.3.3 Barracuda Reference MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.13.4 Using a Syslog Server to Centrally Monitor System Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.13.4.1 Syslog and the Barracuda Spam Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.13.4.2 How to Parse the Barracuda Spam Firewall Syslog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.13.5 How to Set Up Barracuda Cloud Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.13.6 Barracuda Spam Firewall Panel Indicators, Ports, and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.13.7 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.14 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.14.1 How to Back Up and Restore System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.14.2 Replacing a Failed System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.15 Tools and Add-Ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.15.1 Barracuda Spam Firewall API Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.15.2 Barracuda Message Center User's Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.15.3 Barracuda Spam Firewall User 's Guide 6 and Above . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.15.4 Barracuda Spam Firewall User's Guide 5.x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.15.5 Barracuda Outlook Add-In Overview 6 and Above . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.15.6 Barracuda Outlook Add-In Overview 5.x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.15.7 Barracuda Spam Firewall Outlook Add-In Deployment Guide 6.1.2 and Above . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.15.8 Barracuda Spam Firewall Outlook Add-In Deployment Guide 5.x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.15.9 SMTP Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.15.9.1 How to Customize SMTP Response Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.16 Hardware Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. Limited Warranty and License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
148
149
150
151
152
153
154
155
156
157
158
160
161
162
163
164
165
167
168
169
172
173
174
175
176
179
180
184
185
186
188
189
190
191
193
194
195
200
201
202
203
209
214
215
219
221
223
224
225
226
290
292
298
305
307
308
313
315
318
319
320
Barracuda Spam Firewall Administrator's Guide - Page
3
Barracuda Spam Firewall - Overview
en
The Barracuda Spam Firewall is an integrated hardware and software solution designed to protect your email server from spam, virus, spoofing,
phishing and spyware attacks. Outbound filtering and encryption options also prevent confidential or sensitive information from being purposely or
inadvertently leaked outside the organization (Data Leakage Prevention). The optional cloud protection layer (CPL) shields email servers from
inbound malware and DoS attacks while filtering out normal spam before it ever touches the network’s perimeter.
Where to Start
The selected deployment mode may depend on the email server configuration that currently exists at your site, as well as whether you want to
deploy the Barracuda Spam Firewall behind your corporate firewall or in front of your corporate firewall in the DMZ. Refer to Deployment Options
for more information.
Device Deployment
Go to the Getting Started section, or
Download the Barracuda Spam Firewall Quick Start Guide in English or Japanese.
Virtual Deployment
Go to the Barracuda Spam Firewall Vx Quick Start Guide.
Key Features
Spam and virus filtering with the optional Barracuda Exchange Antivirus Agent, an add-in that you can install on your Microsoft Exchange
mailbox server(s).
Global or per-user quarantine
Prevents spoofing, phishing and malware
Data leakage prevention (DLP) with outbound email filtering
SMTP/TLS site-to-site encryption – see How to Use DLP and Encryption of Outbound Mail
Invalid bounce suppression
Policy enforcement for compliance and corporate policies
Copyright © 2015, Barracuda Networks Inc.
4
Release Notes
en
Before installing any firmware version, back up your configuration and read all release notes that apply to versions more recent than
the one currently running on your system.
Do not manually reboot your system at any time during an update, unless otherwise instructed by Barracuda Networks Technical
Support. Depending on your current firmware version and other system factors, updating can take up to 10 minutes. If the process
takes longer, please contact Barracuda Technical Support for further assistance.
Before upgrading, BE SURE TO TAKE THE BARRACUDA SPAM FIREWALL OFFLINE. This will ensure that the inbound queue is
emptied and all messages are scanned before the update process begins. See the BASIC > Administration page for the Offline butto
n.
Updating to Version 7.x
WARNING: After clicking the Apply Now on the ADVANCED > Firmware Update page, the progress bar may appear to time out and the
administrator may need to manually return to the login screen after 5 minutes if it doesn't load automatically in the browser.
If you are using the Require Encrypted TLS relaying email to these destination domains setting on the DOMAINS > Manage
Domain > ADVANCED > Email Protocol page, you must specify the destination domain(s) to which you want to relay outbound mail
over a TLS connection. If you specify an IP address or hostname, then opportunistic TLS will be used.
When updating from firmware version 5.1.3.004 or later, make extra sure that you have a recent backup of your configurations, since
backups taken from firmware versions earlier than 4.1 will NOT restore properly with version 6.x or later. Once you have updated to
version 7.x, Barracuda Networks does not recommend reverting to an older firmware version.
Firmware Version 7.1
What's New in Version 7.1
Barracuda Exchange Antivirus Agent
The new Barracuda Exchange Antivirus Agent 7.1 runs as a Windows service on your Microsoft Exchange 2013 server and enables it to
scan email for viruses. From the ADVANCED > Exchange Antivirus page you can download the agent and view associated email
statistics after it is installed and running. You can also click a link on the page to view the Barracuda Exchange Antivirus Agent release
notes.
This version of the agent only supports Microsoft Exchange Server 2013. If you are using versions 2007 or 2010 of Exchange Server,
you can download the Barracuda Exchange Antivirus Agent 6.0.x from the ADVANCED > Exchange Antivirus page.
The Barracuda Exchange Antivirus Agent no longer supports Microsoft Exchange Server 2003.
See How to Get and Configure Barracuda Exchange Antivirus Agent 7.1 and Above for details.
Cloud Control
Support for Domain Administration and Users management - Barracuda Cloud Control now supports managing domains and users.
Administrators will have the ability to navigate between domains and user's within Barracuda Cloud Control.
Fixed in Version 7.1
Version 7.1.1.001 (Early Release)
Mail Processing
Enhancement: Improved SPF checks for complex records. [BNSF-23979]
Enhancement: Resolved case sensitivity with redirection checks. [BNSF-23979]
Enhancement: Improved DLP detection. [BNSF-24186]
Fix: Resolved case sensitivity issue with SPF and redirection checks. [BNSF-23876, BNSF-24102]
Fix: Messages no longer have the global footer attached if Attach Footer is set to No on the ADVANCED > Outbound Footers page at
the domain level. [BNSF-24148]
Web Interface
Enhancement: Messages that are blocked for intent now contain a link to whitelist the sender. [BNSF-24372]
Enhancement: Updated Japanese translations. [BNSF-23486]
Enhancement: Messages that are allowed for emailreg now contain a link for reporting emailreg abuse. [BNSF-24373]
Enhancement: Improved appearance for popups in Firefox and Internet Explorer. [BNSF-23986]
5
Enhancement: Improved performance of data entry for pages containg large amounts of data. [BNSF-24152]
Enhancement: Improved display of Exchange Antivirus data with multiple Exchange Servers. [BNSF-24220]
Enhancement: Improved handling of message bodies for Bayesian classification. [BNSF-24368, BNSF-24370]
Fix: Marking messages as Spam/Not Spam in the Message Log is now reflected properly on all units in a cluster. [BNSF-9564,
BNSF-22576]
Fix: Resolved an issue where users sometimes could not deliver or delete quarantine messages. [BNSF-22902]
Fix: Clicking action links on the BASIC > Outbound Quarantine page at the domain level no longer redirects to the Dashboard.
[BNSF-23840]
Fix: Message Log now shows correct Delivery Status for all messages in a cluster. [BNSF-23897]
Fix: The State filter on the ADVANCED > Queue Management page now correctly applies for non-English languages. [BNSF-23917]
Fix: Changes to the BLOCK/ACCEPT > Recipient Filters page now take immediate effect on all units in a cluster. [BNSF-24089]
Fix: Resolved issue where sometimes the Delivery Status in the Message Log would not show correct information. [BNSF-24096]
Fix: Messages can now be viewed on all units in a cluster. [BNSF-24140]
Fix: Fixed issue with taking action on quarantined mail in clusters consisting of 3 or more units. [BNSF-24207]
Fix: Fixed display of usernames with special characters. [BNSF-24253]
Fix: Fixed issue where new units may not show initial messages in the Message Log. [BNSF-24309]
Fix: Attachments are again displayed for the end user quarantine. [BNSF-24367]
Fix: Domain administrators can now view messages in the Message Log. [BNSF-24374]
Fix: Help dialogs now show correct titles for multi-byte/high-ascii encoding. [BNSF-24376]
Backup
Fix: Restoring a backup to a virtual machine no longer overwrites the license token. [BNSF-23846]
Security
Fix: resolved the following vulnerabilities:
BNSEC-877, BNCMN-132: Security fix, low severity. Some non-persistent cross-site scripting attacks have been fixed.
Version 7.1.0.002
Web Interface
Fix: Resolved issue where statistics did not display in Barracuda Appliance Control after Barracuda Spam Firewall was rebooted.
[BNSF-24079]
Fix: End users can now log in if the Barracuda Spam Firewall cannot check subscriptions, such as when the internet is unavailable.
[BNSF-24122]
Version 7.1.0.001
Mail Processing
Fix: Messages containing hostnames that are IP addresses in messages are correctly processed. [BNSF-21784, BNSF-23457]
Web Interface
Enhancement: Updated translations. [BNSF-23792, BNSF-223460]
Enhancement: General web interface enhancements in font, color, and styling. [BNSF-23167, BNSF-23169, BNSF-23171]
Enhancement: Improved display of Barracuda Exchange Antivirus Statistics. [BNSF-23791]
Fix: Resolved issue regarding Single Sign-On with LDAP hosts with IPv4 and IPv6 addresses. [BNSF-21422]
Fix: Online Help Search in Firefox correctly supports the Japanese IME keyboard. [BNSF-23116]
Fix: On the BASIC > Outbound Quarantine page, taking actions with messages such as Delete, Reject or Deliver no longer clear the
search filters. [BNSF-23134]
Fix: Message Log buttons and icons for IE 8 and 9 render correctly. [BNSF-23882]
Fix: When using Single Sign-On (SSO) with an LDAP Server Type of Other (see the USERS > LDAP Configuration page for a domain),
the Barracuda Spam Firewall now only uses the user-provided filter for an LDAP search, preventing a timeout. [BNSF-23996]
Fix: Admin, Domain Admin and Helpdesk roles can now deliver user quarantined messages from the Quarantine inbox when the locale is
Multibyte. [BNSF-24062]
Fix: Report data displayed with the Show Report function now matches the data in the emailed report, as the Show Report function
now uses local time for the Date Range as opposed to UTC time. [BNSF-24004]
Barracuda Exchange Antivirus Agent
Enhancement: Barracuda Exchange Antivirus Agent 7.1 verifies signature integrity prior to loading the signatures. [BNSF-21154]
Security
6
High severity vulnerability: persistent XSS, unauthenticated, remotely exploitable [BNSEC-4672 / BNSF-22625]
Web Interface
Updated the Barracuda Spam Firewall web interface with a new color scheme to be consistent with the look and feel with other
Barracuda products. There are no navigation changes.
The Microsoft IE browser is supported for version 8 and above.
New login security feature: If the user login fails 5 times, there is a 15 minute wait period before making another login attempt.
The BASIC > Status page has been renamed to BASIC > Dashboard.
Improved Performance and Security
Mail delivery now supports connection caching, thereby reducing the amount of network traffic as well as load on destination mail
servers.
TLS support is improved and now provides:
Better fallback negotiation
Wildcard support for requiring TLS to destination domains and sub-domains
Certificate validation
Barracuda Spam Firewall Vx virtual machines now show the core capacity and usage on the BASIC > Dashboard page.
Mail Processing
Feature: SMTP response codes for rejected messages can now be customized on the ADVANCED > SMTP Responses page.
[BNSF-20867]
Enhancement: Added support for Recipient Addresses which include address tagging. See Recipient Delimiter on the ADVANCED >
Email Protocol page for more information. [BNSF-7518]
Enhancement: Outbound mail now supports connection caching to destination mail servers. [BNSF-18823]
Enhancement: Updating a per-domain recipient whitelist now takes immediate effect, no longer requiring a Reload. [BNSF-19025]
Enhancement: Improved TLS fallback and detection behavior. [BNSF-19178]
Enhancement: The setting for Require Encrypted TLS relaying email to these destination servers now supports domain names, and
wildcards, rather than specific servers. Click the Help button on the domain level ADVANCED > Email Protocol page for more
information. [BNSF-19640]
Enhancement: Requiring TLS to a destination domain now supports certificate validation instead of checking the hostname.
[BNSF-19807]
Fix: Fixed issue where mail could intermittently stop processing. [BNSF-14626]
Fix: Outbound mail delivery no longer attempts to use IPv6 if the system is configured to only use IPv4. [BNSF-19703]
Fix: Mail which bounced (return notification) due to an un-reachable server no longer shows as Deferred in the Message Log.
[BNSF-19347]
Fix: Comma delimiters separating destination mail servers now correctly enable load balancing. [BNSF-19397]
Fix: Load balancing mode now properly handles fail-over if the attempted destination mail server is unreachable. [BNSF-19398]
Fix: Certain attachment types no longer cause an error when adding footers to emails. [BNSF-21580]
Fix: SPF outbound checks now properly handles private IP addresses and relays between Barracuda Spam Firewalls. [BNSF-21586,
BNSF-22010]
Fix: Barracuda Reputation and RBL IP Exemption Ranges now work as expected with Trusted Forwarders. [BNSF-22623]
Fix: Multiple messages in a single session with invalid recipients no longer works with whitelisting as expected. [BNSF-22478]
Fix: Outbound emails no longer erroneously include footers configured for other domains if a system wide footer is not configured.
[BNSF-22495]
Fix: Inbound mail are no longer incorrectly caught by Predefined credit card filters when the Link Domains feature is used and the
primary domain is not fully configured. [BNSF-22874]
Web Interface
Enhancement: Viewing a message now records the event in Web Syslog (see ADVANCED > Troubleshooting). [BNSF-7402]
Enhancement: The addition of users now verifies that the domain exists on the Barracuda Spam Firewall before adding a user for that
domain. [BNSF-20188]
Enhancement: Updated translations. [BNSF-22551, BNSF-22707]
Enhancement: Support for recently changed time zone/daylight savings times including Moscow and Fiji. [BNSF-22854]
7
Fix: Message Log search filter now properly clears OR conditions when removed from the filter. [BNSF-21295]
Fix: Online Search now properly works when HTTPS/SSL Access Only is enabled. [BNSF-21682]
Fix: Deleting all displayed Emails from the Quarantine Summary Digest now properly deletes the quarantined emails from the system.
[BNSF-22742]
Fix: Helpdesk users can now see headers when Helpdesk users are allowed by the administrator to view headers. [BNSF-22791]
Fix: Downloading an attachment from the Outbound Quarantine no longer forces a logout. [BNSF-22817]
Backup
Enhancement: Added support for FTPS. [BNSF-2658]
Enhancement: Added support for NTLMv2 on ADVANCED > Backup. [BNSF-22061]
Enhancement: Improved reliability and compatibility with SMB targets for backup. [BNSF-22270]
Fix: FTP PASV detection works for legacy restores. [BNSF-22678]
Security
Medium severity vulnerability: non-persistent XSS, authenticated [BNSEC-4544 / BNSF-22332]
Medium severity vulnerability: non-persistent XSS, authenticated [BNSEC-4528 / BNSF-22334]
Medium severity vulnerability: authenticated, security control bypass [BNSEC-3246 / BNSF-21595]
Low severity vulnerability: non-persistent XSS, authenticated [BNSEC-4531 / BNSF-22333]
Version 7.0.0.004
Fix: Resolved issue with connecting to recipient servers when Enable SMTP over TLS/SSL is turned on (see the ADVANCED > Email
Protocol page).
Email Categorization
This feature gives administrators an additional way to decide what to do with various types of emails from senders on the Barracuda
Reputation Whitelist. These emails are separated into different categories such as Transactional, Corporate and Marketing, each of
which can have a different delivery action associated with it.
Extended Malware Protection (Available on model 600 and higher)
An additional layer of deep message scanning is available as Extended Malware Protection leveraging a third-party scanner. This feature
is only available with a subscription. Contact your local Barracuda Networks Sales Reseller to purchase this subscription.
Barracuda Outlook Add-in (Available on some models)
Note: To run version 6.1.4.001 of the Barracuda Spam Firewall firmware, you must update your Barracuda Outlook Add-in to version
6.1.11 or later (see the USERS > User Features page).
Version 6.1.5.008
Fix: Resolved issue with connecting to recipient servers when Enable SMTP over TLS/SSL is turned on (see the ADVANCED > Email
Protocol page).
Version 6.1.5.006
Web Interface
Fix: Resolved issue with rare cases of some charts on the BASIC > Status page not rendering correctly. [BNSF-22184]
Mail Processing
Fix: TLS 1.1 and 1.2 remain available when SSLv2 and SSLv3 are disabled. [BNSF-22876]
Version 6.1.5.004
Virtualization
8
Feature: Added support for hourly billing virtual deployment in Microsoft Azure. [BNSF-22841]
Version 6.1.5.003
Web Interface
Fix: SSLv3 is disabled by default in the web interface to mitigate CVE-2014-3566 (SSL POODLE). [BNSF-22788]
Mail Processing
Enhancement: New setting on ADVANCED > Email Protocol page to allow or disallow SSLv2 and SSLv3 for incoming SMTP
connections. Setting to Yes provides for greater compatibility with older mail servers. Set to No to mitigate the recently reported SSL
POODLE [CVE-2014-3566] issue. [BNSF-22788]
Fix: Resolved an issue in the encryption module that affected transmission of outbound messages over a TLS connection to some types
of mail servers. [BNSF-22782]
Version 6.1.5
Mail Processing
Feature: Added support for Perfect Forward Secrecy in the following two scenarios: [BNSF-21503]
When sending SMTP traffic over a TLS connection. To configure SMTP over TLS, see Enable SMTP over TLS/SSL on the AD
VANCED > Email Protocol page.
When using HTTPS access for the Barracuda Spam Firewall web interface. This requires using properly configured SSL
certificates. See the ADVANCED > Secure Administration page to configure certificates.
Barracuda Appliance Control
Fix: From the Barracuda Appliance Control interface, clicking on a message in the Message Log properly renders the Message Details
popup window and message information. [BNSF-22666]
Fixed in Version 6.1.4
Version 6.1.4.001:
Mail Processing
Enhancement: Improved concurrent processing performance of the Barracuda Spam Firewall 900. [BNSF-21877]
Enhancement: Improved message body scanning. [BNSF-21891]
Enhancement: Optimized performance of Barracuda Reputation Blocklist resource utilization, update, and lookup. [BNSF-22036]
Enhancement: Header filters can now be applied to the Received header added by the Barracuda Spam Firewall. [BNSF-22101]
Enhancement: Improved performance of recipient verification lookup when Local Database is not in use. [BNSF-22185]
Enhancement: Improved resource utilization for scoring and attachment scanning. [BNSF-22266]
Enhancement: Valid and Explicit Recipients no longer require the primary email address to be listed twice on the ADVANCED > Explicit
Users page (at the global level) or the USERS > Valid Recipients page (at the domain level). [BNSF-22357]
Enhancement: Improved memory performance with attachment processing. [BNSF-22362]
Fix: In clustered environments, Per-User Quarantine accounts now support special characters such as apostrophes, for example.
[BNSF-16814]
Fix: Archiving of encrypted messages handles TLS-based connections correctly. [BNSF-21150]
Fix: Plain text footers are not duplicated if the footer is multi-line. [BNSF-21376]
Fix: Resolved issue which could prevent statistics and Message Log from updating. [BNSF-21848]
Fix: Quarantined messages with multi-byte characters in the headers can now be delivered. [BNSF-21964]
Fix: PTR record analysis now properly handles Trusted Forwarders when a connection is made. [BNSF-22196]
Fix: Resolved intermittent logging issue which, at times, used disk space on the firmware partition. [BNSF-22201]
Fix: Now all messages from a whitelisted IP address in a single session are whitelisted. Previously only the first message was
whitelisted. [BNSF-22205]
Fix: Resolved long delay for display of BASIC > Status and ADVANCED > Energize Updates pages when offline updates are used.
[BNSF-22258]
Fix: Improved performance when Energize Updates are applied on a Barracuda Spam Firewall appliance under heavy System Load.
[BNSF-22300, BNSF-22398]
Fix: Outbound quarantine now works on the Barracuda Spam Firewall 100 and 200. [BNSF-22351]
Reporting
Fix: Email Encryption Details report columns are correctly labeled. [BNSF-22095]
Web Interface
9
Enhancement: Password values changed via the Support Tunnel are now masked from Syslog output. [BNSF-22018]
Enhancement: Added Russian translations to NDR templates. [BNSF-22323]
Enhancement: Included Icelandic translations for end user pages in the web interface. [BNSF-22358]
Fix: Resolved case sensitivity issue when domain names are referenced in various settings. [BNSF-21358]
Fix: Web interface no longer displays "Temporarily Unavailable" if an invalid character set attribute is detected. [BNSF-22180,
BNSF-22240]
Backup
Fix: When restoring a backup to a new Barracuda Spam Firewall, upgraded to the most recent firmware, you are no longer required to do
a Reload to prevent an "Invalid Domain" response. [BNSF-20703]
Fix: Resolved issue which could prevent backup jobs from completing. [BNSF-21915]
Fix: Backups can now be restored if the web browser is configured for Japanese character sets. [BNSF-22364]
Barracuda Outlook Add-in
Fix: The Barracuda Spam Firewall now returns error messages when appropriate from the Barracuda Outlook Add-in and Exchange
Antivirus Add-in. [BNSF-22220]
Fix: The Barracuda Outlook Add-in now properly detects the custom HTTPS port. [BNSF-22382]
Security
Medium - High severity vulnerability: insufficient authorization. [BNSEC-4517 / BNSF-21063]
Medium - High severity vulnerability: non-persistent XSS, unauthenticated. [BNSEC-1251 / BNSF-20597]
Low severity vulnerability: unauthenticated, remotely exploitable, information disclosure. [BNSEC-3421 / BNSF-21649]
Version 6.1.2.003:
Mail Processing
Fix: Prevent the Spam Intent Category in Intent Analysis from defaulting to Off on upgrade. If a previous upgrade has occurred, please
see the Intent Categories table for BASIC > Spam Checking page and verify the setting. [BNSF-21927]
Version 6.1.2.002:
Security
Fix: Resolved the following vulnerability:
Medium severity: Updated OpenSSL to address the issues reported in OpenSSL's security advisory dated 2014-06-05
[BNSEC-4499 / BNSF-22245]
Version 6.1.2.001:
Mail Processing
Enhancement: Improved DLP detection algorithms for birth dates. [BNSF-21396]
Enhancement: Improved handling of unusually formatted emails. [BNSF-21407]
Fix: Messages were erroneously blocked by attachment type when whitelisted by the sender. [BNSF-20505]
Fix: Messages with certain malformed headers now appear correctly in the message log. [BNSF-21305]
Fix: Resolved issues with malformed headers from Trusted Forwarders. [BNSF-21897, BNSF-21906]
Fix: Multiple messages in a single session are no longer encrypted after a message encrypted via the Outlook Add-in. [BNSF-21955]
Fix: Per-User Scoring is no longer used when disabled. [BNSF-21800]
Web Interface
Feature: Added ability to submit Email Categories for incorrect or uncategorized messages. [BNSF-21700]
Feature: Added support for Europe/Busingen timezone. [BNSF-21988]
Enhancement: Improved memory handling and performance of the Web Interface after long periods of time. [BNSF-22142, BNSF-22155]
Fix: Resolved sporadic issue where Basic > Status page would fail to load. [BNSF-21994, BNSF-22184]
Fix: Deprecated timezones are not correctly updated when restored from a backup. [BNSF-21770, BNSF-21836]
Fix: Messages can now be delivered from any box in a cluster. [BNSF-22083]
Backup
10
Fix: Resolved intermittent scenario in which Restore would fail if a previous backup or restore had failed. [BNSF-21257]
Fix: Scheduled Backups Destination can now be changed from Cloud. [BNSF-21286]
Cloud Control
Fix: The Cloud Control status chart now shows the correct date for the status bars. [BNSF-21842]
Security
High severity vulnerability: unauthenticated, remotely exploitable, HTTP header injection [BNSEC-1168 / BNSF-20796]
Version 6.1.1.001:
Virtualization
Feature: Added support for virtual deployment in Amazon Web Services. [BNSF-21875]
Version 6.1.0.003:
Mail Processing
Enhancement: Improved processing of attachment filenames. [BNSF-21995]
Web Interface
Fix: Bulk editing the list of domains no longer omits certain domains. [BNSF-21742]
Enhancement: Added support for localized web interface for Email Categorization. [BNSF-22029]
Version 6.1.0.001:
Mail Processing
Feature: Email Categorization. Messages from Barracuda-verified senders (including those on the Barracuda Reputation Whitelist) are
categorized to allow the administrator another way to determine what action to take on various types of emails. Actions for each
Category may be configured from the BLOCK/ACCEPT > IP Reputation page. [BNSF-21615]
Feature: An additional layer of malware detection has been added with the Extended Malware feature. [BNSF-21662]
Enhancement: Per-Domain whitelisting and blocklisting of IP addresses now honors Trusted Forwarder status. [BNSF-13907]
Fix: Improved processing of messages with very long URLs. [BNSF-21779]
Fix: Improved handling of Received headers containing missing IP addresses. [BNSF-21793]
Web Interface
Feature: The Message Log now contains the IP address of the destination server. [BNSF-21404]
Feature: The Message Debug Identifier has been added to the Queue Managment for easier tracing of messages. [BNSF-21405]
Fix: Changing the character set in the Message Viewer now shows the message rather than the login page. [BNSF-21348]
Fix: APIs now properly account for colons in regex values. [BNSF-21522]
Fix: Adding valid recipients is now logged to the GUI syslog. [BNSF-21536]
Fix: Explicit users are not supported by the list_valid_recipient_aliases API call. [BNSF-21768]
Reporting
Fix: LDAP Failure notification report now accounts for case changes in domains. [BNSF-17538]
Security
Fix: Resolved the following vulnerabilities:
High severity: Authentication bypass [BNSEC-3188 / BNSF-21585]
Medium - High severity: Requires authentication; security control bypass [BNSEC-3208 / BNSF-21593]
Medium severity: Requires authentication; denial of service [BNSEC-3297 / BNSF-21598]
Medium severity: Unauthenticated; information disclosure [BNSEC-3259 / BNSF-21596]
Medium severity: Requires authentication; security control bypass [BNSEC-3198 / BNSF-21591]
Low severity: Unauthenticated; remotely exploitable; information disclosure [BNSEC-3421 / BNSF-21649]
Low severity: Non-persistent XSS; requires authentication; remotely exploitable [BNSEC-3287 / BNSF-21597]
11
Web Interface
Updated Time Zone settings per new 2013 DST settings. - The following time zones have been converted (see the BASIC > Administration
page):
Old Time Zone
New Time Zone
AQ
-9000+00000
Antarctica/South Pole
Amundsen-Scott Station, South
Pole
Antarctica/McMurdo
CA
+4531-07334
America/Montreal Eastern Time
- Quebec - most locations
Toronto
US
+364708-1084111
America/Shiprock Mountain
Time; Navajo
America/Denver
America/Shiprock
Cloud Services
Cloud Backup - New option to back up to the Barracuda Cloud with the same backup features as always, configurable from the ADVAN
CED > Backup page. Use your Barracuda Customer Account credentials to connect. If you don't have an account, you can create one
following instructions in this Barracuda TechLibrary article: Create a Barracuda Cloud Control Account, or see the ADVANCED > Cloud
Control page.
Cloud Protection Layer (CPL) - Now provides an integrated Message Log together with messages processed by the Barracuda Spam
Firewall.
Encryption
More reports detailing number of encrypted emails sent, number of encrypted emails opened by recipients, policies that triggered
encryption action and number of recalled messages.
Ability to archive encrypted email threads to a specified Barracuda Message Archiver. Configured on the BASIC > Administration page,
this feature will archive all encrypted correspondence, including encrypted replies, for all domains that have been validated on the
Barracuda Spam Firewall.
Message Privacy
New Governance, Risk Management and Compliance (GRC) role. The GRC role is used as a way to provide governance, risk
management and compliance to email content. The GRC only has access to Outbound Quarantine logs via the web interface and has
the job of reviewing the messages in the log, determining which ones should be delivered or rejected based on policy. The administrator
can enable or disable the GRC account at any time. Configure on the BASIC > Administration page.
Message Log Privacy - To protect email privacy, you can enable the Secondary Authorization feature to require a password before
the Admin, Domain Admin or Helpdesk roles can view entries or email message contents across the system (including the global
Message Log, per-domain Message Logs, queue management, outbound quarantine and quarantine inboxes). Configure on the BASIC
> Administration page.
SSL Certificates
SSL Certificate generation and installation process improvement.
Reporting
The Top Count setting upper limit, which is the maximum number of rows returned in a report (e.g. Top 10 Viruses), has been reduced
to 50. See the BASIC > Reports page.
Add-ins
The Barracuda Outlook Add-in supports Outlook 2007, Outlook 2010 and 2013. Support for Outlook XP and 2003 is no longer
available.
Note: If you are running version 6.0.0.028 of the Barracuda Spam Firewall firmware, you must upgrade your Barracuda Outlook Add-in to
version 6.0.x or later (see the USERS > User Features page).
The Lotus Notes Plugin is no longer supported, starting in Firmware Release 6.0.
12
Version 6.0.2.002:
Mail Processing
Enhancement: Multi-level intent analysis consistently handles timeouts. [BNSF-21731]
Fix: PTR record analysis now honors Trusted Forwarder status; i.e. IP addresses are checked until and including the first IP that is not a
trusted forwarder. [BNSF-21559]
Web Interface
Updated Time Zone settings per new 2013 DST settings. - The following time zones have been converted (see the BASIC >
Administration page):
Old Time Zone
New Time Zone
AQ
-9000+00000
Antarctica/South Pole
Amundsen-Scott Station, South
Pole
Antarctica/McMurdo
CA
+4531-07334
America/Montreal Eastern Time
- Quebec - most locations
Toronto
US
+364708-1084111
America/Shiprock Mountain
Time; Navajo
America/Denver
America/Shiprock
Fix: Converted time zones per new 2013 DST settings. [BNSF-21277].
The following time zones have been converted:
Antarctica/South Pole, Amundsen-Scott Station, South Pole. New Time Zone: Antarctica/McMurdo
America/Montreal Eastern Time - Quebec - most locations. New Time Zone: Toronto
America/Shiprock Mountain Time, Navajo. New Time Zone: America/Denver America/Shiprock
Fix: Bulk editing the list of domains no longer omits certain domains. [BNSF-21742].
Version 6.0.2.001:
Mail Processing
Enhancement: Improved Sender Policy Framework (SPF) algorithms for increased accuracy. [BNSF-18114, BNSF-20387, BNSF-20523,
BNSF-20558, BNSF-20883, BNSF-21068, BNSF-21118]
Enhancement: Hard SPF detection failures are now enabled by default. [BNSF-17929]
Enhancement: Inbound mail from a Trusted Relay source is now subject to Recipient Verification (if configured) to prevent sending email
to an invalid user for the domain. [BNSF-20482].
Enhancement: Mail Journaling can now be configured to only journal Quarantined messages on delivery. [BNSF-19388]
Enhancement: Multi-level intent analysis performs better with slow web servers. [BNSF-20003]
Enhancement: Improved disk space management. [BNSF-20543, BNSF-21026, BNSF-21339, BNSF-21308]
Enhancement: Improved recovery of services that are in an inconsistent state. [BNSF-20656, BNSF-20802, BNSF-20898]
Enhancement: Improved real-time detection for multilevel intent analysis. [BNSF-20733]
Enhancement: Improved attachment detection and filtering. [BNSF-19488]
Enhancement: Optimized analysis of messages with compressed files (.tgz, .rar, .zip). [BNSF-21147]
Enhancement: Improved DLP detection algorithms for message contents and attachments, including those for identifying dates, credit
card information, and data in Excel files. [BNSF-21094, BNSF-21354, BNSF-20736, BNSF-21272]
Enhancement: Added default German NDR texts. [BNSF-21058]
Fix: The Create Password email can now be sent to users with spaces in the UID. [BNSF-14773]
Fix: Block Sender Verify is no longer disabled when Block Empty Sender is enabled. [BNSF-14977]
Fix: PTR record analysis is now performed when mail is received from a Trusted Forwarder. [BNSF-19257]
Fix: All messages in a single SMTP session are now whitelisted when sent from a whitelisted IP address. [BNSF-19779, BNSF-20562]
Fix: Improved whitelist setting interactions between a primary account and its LDAP or Valid Recipient alias. [BNSF-20592, BNSF-21453]
Fix: Improved detection of UPS tracking numbers previously mis-identified as Social Security Numbers. [BNSF-19577]
Fix: Outbound Quarantine messages could be delivered to the Inbound Quarantine address with the Inbound Quarantine tag when using
Global Quarantine. [BNSF-20032]
Fix: Resolved issue processing messages with headers including ports with IP addresses. [BNSF-20524]
Fix: Messages blocked due to file type now report as banned rather than accepted. [BNSF-20525]
Fix: Whitelist properly takes precedence over quarantine rules that are based on EmailReg settings. [BNSF-20934]
Fix: Resolved issue in which, in rare circumstances, per-user quarantine files could be written as zero bytes when in a clustered
environment. [BNSF-20991]
Fix: Spam analysis conditions which could prevent unusual messages from being processed. [BNSF-20994, BNSF-20997]
Web Interface
13
Enhancement: Improved web interface performance when displaying a large number of users or domains. [BNSF-18336]
Enhancement: Reduced time to reload system configurations when there are a large number of domains. [BNSF-20145]
Enhancement: Single Sign-On now honors Valid Recipient alias linking. [BNSF-19754]
Enhancement: Improved support for Internet Explorer 9 and 10 and Firefox 23 and Safari. [BNSF-19525, BNSF-19837, BNSF-19978,
BNSF-20259, BNSF-21324, BNSF-21244]
Enhancement: Manual Backups now show the correct status without requiring a manual refresh. [BNSF-19836]
Enhancement: Improved detection of malformed character sets when displaying unicode messages. [BNSF-20503]
Enhancement: Added 3 new methods to API to list, add and delete Valid Recipients. [BNSF-20605]
Enhancement: The SMTP port is now excluded from synchronization across systems in a cluster. [BNSF-20561]
Enhancement: Option for the Helpdesk role to view message headers (configured on the BASIC > Administration page).
[BNSF-21204]
Enhancement: Web Syslog contents now include the year, usernames, troubleshooting commands, and configuration changes made by
Barracuda Technical Support. May require a restart of your syslog clients in order to receive the additional data. [BNSF-20990,
Enhancement: Updated translations. [BNSF-19999, BNSF-20000, BNSF-20217, BNSF-20325, BNSF-20862, BNSF-21123,
BNSF-21418]
Fix: Time zone updates for Israel per new 2013 DST settings. [BNSF-21277]
Fix: Journaling to the Barracuda Message Archiver now accepts an IP address. [BNSF-13505]
Fix: Corrected handling of unicode characters in user whitelists. [BNSF-13751]
Fix: Reduced time to log into the web interface when the update server is not reachable. [BNSF-18333]
Fix: Improved handling of special characters such as '$' in the LDAP password for Single Sign-On users. [BNSF-19396]
Fix: All users are now able to view quarantine messages when a device is removed from a cluster. [BNSF-19567]
Fix: Viewing message bodies in a clustered environment no longer results in an error for some messages. [BNSF-21449]
Fix: Searching the outbound quarantine from a user's account no longer forces a logout. [BNSF-19775]
Fix: Repaired erroneous validation of the Message Log's Time Range filters. [BNSF-20218]
Fix: Repaired Time Range searches of Outbound messages in the Message Log. [BNSF-21273]
Fix: Message Log filter errors are now properly encoded. [BNSF-19968]
Fix: The Barracuda Spam & Virus Firewall Vx now displays the correct expiration date for Energize Updates subscriptions. [BNSF-20076]
Fix: The SNMP agent starts correctly on the Barracuda Spam & Virus Firewall Vx. [BNSF-19478]
Fix: Graceful shutdown via the power button now works in all cases. [BNSF-20706]
Fix: The "ping" command works as expected with IPv6. [BNSF-20726]
Fix: Performance statistics are now displayed when viewing the BASIC > Status page in the web interface page for the Chinese locale.
[BNSF-21156]
Backup
Enhancement: FTP backups now supports both active and passive modes. [BNSF-7762]
Fix: SMB shares are now always unmounted after a backup. [BNSF-19249]
Fix: Repaired display of backup files available via FTP. [BNSF-21332]
Cloud Control
Feature: The ADVANCED > Queue Management page is now available from Barracuda Cloud Control. [BNSF-19534]
Fix: Errors restoring backups are now propagated to the top level of the Barracuda Cloud Control tree. [BNSF-19534]
Fix: Repaired of links for running/completed tasks. [BNSF-20186, BNSF-20194]
This firmware version requires update of your Barracuda Outlook Add-in (see the USERS > User Features page) to version 6.0.40 or
later.
Enhancement: Classification buttons are now available for public folders. [BNSF-20670]
Enhancement: The Alternate URL was removed from the ADM configuration in favor of auto-provisioning. [BNSF-20670]
Fix: The property page now shows correctly in Outlook 2007. [BNSF-21300]
Fix: The Add-in no longer fails to start if a localization is unavailable. [BNSF-21492]
Exchange Antivirus
Enhancement: Improved handling of corrupted virus definition updates. [BNSF-20648]
Fix: The Exchange Antivirus Agent now starts for all localized versions of Microsoft Exchange. [BNSF-19315]
Security
High severity: Persistent XSS; unauthenticated; remotely exploitable. [BNSEC-2590]
High severity: Authentication bypass. [BNSEC-2625]
High severity: Information disclosure. [BNSEC-2816]
Medium severity: Unauthenticated; information disclosure. [BNSEC-1658]
14
Medium severity: Information disclosure. [BNSEC-2814]
Low - Medium severity: Persistent XSS; unauthenticated; authentication bypass. [BNSEC-2563]
Low severity: Persistent XSS; requires authentication; remotely exploitable. [BNSEC-220]
Low severity: Non-persistent XSS; requires authentication; remotely exploitable. [BNSEC-1052]
Version 6.0.0.029:
Mail Processing
Enhancement: Improved real-time detection of malformed attachments. [BNSF-21142].
Security
High severity: Persistent XSS; unauthenticated; remotely exploitable. [BNSEC-1550 / BNSF-20929]
High severity: Persistent XSS; unauthenticated; remotely exploitable. [BNSEC-1650 / BNSF-20943]
Medium - High severity: Non-persistent XSS; unauthenticated [BNSEC-1251 / BNSF-20597]
Low - High severity: Persistent XSS; requires authentication. [BNSEC-391 / BNSF-19756]
Low - High severity: Non-persistent XSS; requires authentication [BNSEC-1068 / BNSF-20228]
Low - High severity: Requires authentication; information disclosure. [BNSEC-1706 / BNSF-20955]
Medium severity: Information disclosure. [BNSEC-107 / BNSF-17460]
Low - Medium severity: Unauthenticated; information disclosure. [BNSEC-1746 / BNSF-20978]
Low severity: Persistent XSS; requires authentication. [BNSEC-220 / BNSF-18321]
Low severity: Persistent XSS; requires authentication. [BNSEC-1702 / BNSF-20953]
Low severity: Non-persistent XSS; requires authentication. [BNSEC-1152 / BNSF-20394]
Low severity: Requires authentication; information disclosure. [BNSEC-1160 / BNSF-20396]
Low severity: [BNSEC-1383 / BNSF-20817]
Version 6.0.0.028:
Mail Processing
Enhancement: Access to Upgraded Barracuda Real Time Systems (BRTS). The Upgraded BRTS is significantly faster and leverages
additional lookups and faster detection operations. with this BRTS Upgrade, the Barracuda Spam Firewall can adapt to spam faster and
more accurately. [BNSF-20859]
This firmware version requires upgrade of your Barracuda Outlook Add-in (see the USERS > User Features page) to version 6.0.21 or later.
Web Interface
Fix: Firmware Upgrades no longer fail to show progress in some cases. [BNSF-20790]
Version 6.0.0.027:
Web Interface
Fix: The Search button returns the correct result set the first time it is clicked when using the 'Time' search filter. [BNSF-20591]
Fix: Time zone Upgrades for Chile and Paraguay per new 2013 DST settings. [BNSF-20522]
Version 6.0.0.018
Security
Enhancement: Per-User Allow and Block lists now check Envelope From and Header From. [BNSF-17727]
Fix: Reflective cross-site scripting issue in ADVANCED > Troubleshooting page. [BNSEC-1088]
Version 6.0.0.015
Security
Fix: Resolved issue with potential SSH access to unit when not deployed behind a firewall. To completely disable remote support
functionality, contact Barracuda Networks Technical Support. Reported by Stefan Viehck, SEC Consult Vulnerability Lab (https://www.se
c-consult.com). [BNSEC-767]
15
Version 6.0.0.007:
Backup
Feature: Improved backup user interface. [BNSF-19325]
Enhancement: Backup files are deleted upon successful completion of a backup. [BNSF-18628]
Enhancement: Restoring a backup no longer restores Advanced Network information. [BNSF-18957]
Enhancement: Configuration backups are now encrypted. [BNSF-19496]
Fix: Backup does not fail if there are special characters in the login name or password. [BNSF-14472]
Fix: SMB mounts are now automatically dismounted after a backup. [BNSF-14625]
Fix: Restoring a backup configuration now immediately processes mail for domains without requiring a Reload. [BNSF-19350]
Mail Processing
Enhancement: Disabling SMTP Over TLS at the system level no longer rejects domains which are required by the Domain-level Force
TLS settings. [BNSF-17474]
Enhancement: Spoof Protection now looks at headers in addition to the envelope content. [BNSF-17679, BNSF-15997]
Enhancement: Whitelisted messages are now flagged as whitelisted if Trusted Forwarders are configured on the BASIC > IP
Configuration page. [BNSF-17943]
Enhancement: Active directory default LDAP filter has been modified to reduce AD CPU load. [BNSF-17993]
Enhancement: Improved HIPAA medical term detection in email content. [BNSF-18390]
Enhancement: Malicious URL scanning now correctly scans all HTML attachments. [BNSF-18564]
Enhancement: TNEF files are now scanned for viruses. [BNSF-18921]
Enhancement: Added the ability to exempt email addresses and domains from encryption from the BASIC > Administration page.
[BNSF-18949]
Enhancement: Improved recipient verification performance if no Explicit Users are defined. [BNSF-19048]
Enhancement: Improved false positive detection in XLSX files for DLP settings. [BNSF-18738]
Enhancement: TLS can now be required for all incoming domains from the Domain-level ADVANCED > Email Protocol page.
[BNSF-19738]
Fix: Duplicate X-Barracuda-IPDD header lines are no longer added. [BNSF-15751]
Fix: Duplicate X-Barracuda-Registry header lines are no longer added. [BNSF-19829]
Fix: The Queue Management timestamp now matches the message log timestamp in all cases. [BNSF-19149]
Fix: Improved processing performance for large multipart text emails. [BNSF-19644]
Fix: Attachment filter now correctly detects video file types with altered extensions. [BNSF-18977]
Fix: LDAP routing will now enable alias rewriting if username/password are not set. [BNSF-19114]
Fix: URL inspection now correctly handles UTF-8 characters. [BNSF-19575]
Fix: Improved process monitoring of front end scanning engine. [BNSF-19675]
Fix: Appliance remains offline after a firmware upgrade if it is already in offline mode. [BNSF-18941, BNSF-19705]
Fix: Rate control settings for POP accounts are now applied correctly. [BNSF-19745]
Cloud Control
Enhancement: Added Users and Advanced pages to Barracuda Cloud Control administration. [BNSF-16098, BNSF-16288]
Enhancement: Passwords are masked in syslog output. [BNSF-16498]
Fix: Unicode characters can now be added to tables through the Barracuda Cloud Control. [BNSF-18087]
Reporting
Fix: Report performance has been optimized. [BNSF-16599, BNSF-17853]
Fix: Queue details now include the To address. [BNSF-17127, BNSF-18516]
Fix: LDAP failures are now sent to all email addresses when addresses include Unicode characters. [BNSF-18491]
Fix: Traffic reports are no longer sorted in reverse order. [BNSF-18673]
Web Interface
Feature: Improved syslog performance [BNSF-18033]
Feature: Destination Mail Servers can now be defined using an MX record. [BNSF-19358]
Enhancement: Syslog now logs 'Guest' logins. [BNSF-18102]
Enhancement: Improved webInterface performance. [BNSF-18378]
Enhancement: Improved search performance of message log in a clustered environment. [BNSF-17385, BNSF-18734]
Fix: Clustering is now removed from Running Tasks when complete. [BNSF-9554]
Fix: Changing the hostname or destination mail server now takes immediate effect. [BNSF-17616, BNSF-19279]
Fix: Adding a new domain now takes effect immediately without requiring a Reload. [BNSF-17673]
Fix: Resolved false notification of "old static routes on your system". [BNSF-17963]
Fix: Domain Admins can now set an end user to the HelpDesk role. [BNSF-18843]
Fix: Message log could fail to display under some circumstances. [BNSF-18921]
Fix: The Troubleshooting Telnet Utilities no longer omits the connection banner when telnetting to a mail server. [BNSF-19163]
16
Fix: Product tips no longer expand to the entire browser width. [BNSF-19669]
Fix: Message Log is no longer sorted based on the Queue Management sort. [BNSF-16315]
Fix: Product tips now properly expire [BNSF-19661]
Add-in
Feature: Outlook Add-in now supports Outlook 2013. [BNSF-19535]
Fix: Outlook Add-in no longer creates user accounts if quarantine is set to Global. [BNSF-18883]
Version 5.1.3.007:
Mail Processing
Enhancement: Multi-level intent analysis consistently handles timeouts. [BNSF-21731]
Fix: PTR record analysis now honors Trusted Forwarder status; i.e. IP addresses are checked until and including the first IP that is not a
trusted forwarder. [BNSF-21490]
Web Interface
Fix: Updated time zones per new 2013 DST settings. [BNSF-21277].
The following time zones have been converted:
Antarctica/South Pole, Amundsen-Scott Station, South Pole. New Time Zone: Antarctica/McMurdo
America/Montreal Eastern Time - Quebec - most locations. New Time Zone: Toronto
America/Shiprock Mountain Time, Navajo. New Time Zone: America/Denver America/Shiprock
Fix: Changing character set in the message viewer now shows the message body rather than a login screen. [BNSF-21348]
Fix: Quarantined messages can now be viewed from any Barracuda Spam Firewall in a cluster. [BNSF-21348]
Fix: Helpdesk users can view their own quarantined messages. [BNSF-21480]
Cloud Control
Fix: Barracuda Cloud Control shows correct status for firmware and subscriptions on the BASIC > Status page. [BNSF-21521]
This firmware version requires update of your Barracuda Outlook Add-in (see the USERS > User Features page) to version 6.0.40 or later.
Feature: Outlook Add-in now supports Outlook 2013. [BNSF-19535]
Enhancement: Classification buttons are now available for public folders. [BNSF-20670]
Fix: The property page shows correctly in Outlook 2003 and 2007. [BNSF-21300]
Fix: The Outlook add-in starts even if a localization is unavailable. [BNSF-21492]
Security
High severity: Authentication bypass. [BNSEC-2625]
Low - Medium severity: Persistent XSS; unauthenticated; authentication bypass. [BNSEC-2563]
Version 5.1.3.006:
Mail Processing
Enhancement: Improved Sender Policy Framework (SPF) algorithms for increased accuracy. [BNSF-18114, BNSF-20387, BNSF-20523,
Enhancement: Multi-level intent analysis performs better with slow web servers. [BNSF-20003]
Enhancement: Improved disk space management. [BNSF-20543, BNSF-21026, BNSF-21339, BNSF-21308]
Enhancement: Improved recovery of services that are in an inconsistent state. [BNSF-20656, BNSF-20802, BNSF-20898]
Enhancement: Improved credit card detection accuracy. [BNSF-20736, BNSF-21272]
Enhancement: Improved Real-Time Protection performance for archived files. [BNSF-21147]
Fix: The Create Password email can now be sent to users with spaces in the UID. [BNSF-14773]
Fix: Block Sender Verify is no longer disabled when Block Empty Sender is enabled. [BNSF-14977]
Fix: PTR record analysis is now performed when mail is received from a Trusted Forwarder. [BNSF-19257]
Fix: All messages in a single SMTP session are now whitelisted when sent from a whitelisted IP address. [BNSF-19779, BNSF-20562]
Fix: Improved whitelist setting interactions between a primary account and its LDAP or Valid Recipient alias. [BNSF-20592]
Fix: Resolved issue in which, in rare circumstances, per-user quarantine files could be written as zero bytes when in a clustered
17
environment. [BNSF-20991]
Fix: Whitelist properly takes precedence over quarantine rules that are based on EmailReg settings. [BNSF-20934]
Fix: Spam analysis conditions which could prevent unusual messages from being processed. [BNSF-20994, BNSF-20997]
Web Interface
Enhancement: Improved web interface performance when displaying a large number of users or domains. [BNSF-18336]
Enhancement: Reduced time to reload system configurations when there are a large number of domains. [BNSF-20145]
Enhancement: Improved support for Internet Explorer 9 and 10 and Firefox 23. [BNSF-20259, BNSF-21324, BNSF-21244]
Enhancement: Improved detection of malformed character sets when displaying unicode messsages. [BNSF-20503]
Enhancement: Added 3 new methods to API to list and edit Valid Recipients. [BNSF-20605]
Enhancement: Web Syslog now includes troubleshooting commands. [BNSF-20990]
Fix: Corrected handling of unicode characters in user whitelists. [BNSF-13751]
Fix: Reduced time to log into the web interface when the update server is not reachable. [BNSF-18333]
Fix: Improved handling of special characters such as '$' in the LDAP password for Single Sign-On users. [BNSF-19396]
Fix: The SNMP agent starts correctly on Vx models. [BNSF-19478]
Fix: All users are now able to view quarantine messages when a device is removed from a cluster. [BNSF-19567]
Fix: Searching the outbound quarantine from a user's account no longer forces a logout. [BNSF-19775]
Fix: Vx models now display the correct expiration date for Energize Updates subscriptions. [BNSF-20076]
Fix: Performance statistics are now displayed when viewing the BASIC > Status page in the web interface page for the Chinese locale.
[BNSF-21156]
Backup
Fix: SMB shares are now always unmounted after a backup. [BNSF-19249]
Fix: Backup retention policy is now correctly enforced when Bayesian database is not included. [BNSF-21022]
Add-in
Feature: Barracuda Outlook Add-in now supports Outlook 2013. [BNSF-21346]
Security
Medium severity: Unauthenticated, URL redirection. Reported by David Niedermaier. [BNSEC-1800 / BNSF-21024]
Low severity: Persistent XSS, requires authentication. Reported by Max Corrientes. [BNSEC-220 / BNSF-18321]
Low severity: Persistent XSS, requires authentication, remotely exploitable. Reported by Maxim Rupp. [BNSEC-1001 /
BNSF-18321]
Low severity: Non-persistent XSS, requires authentication, remotely exploitable. Reported by Yogesh Jaygadkar
(jaygadkar.com). [BNSEC-1052 / BNSF-20474]
Version 5.1.3.005:
Mail Processing
Enhancement: Improved real-time detection for multi-level intent analysis. [BNSF-20733].
Enhancement: Improved real-time detection of malformed attachments. [BNSF-21142].
Web Interface
Fix: Graceful shutdown via powerbutton now works in all cases. [BNSF-20706].
Security
BNSEC-107 reported by Luca Carettoni
BNSEC-509 reported by Dinesh Shetty
BNSEC-1152 reported by secbounty
BNSEC-1550 reported by Justin Steven (justinsteven.com)
BNSEC-1788 reported by David Niedermaier
18
Version 5.1.3.004:
Mail Processing
Fix: Inbound mail from a Trusted Relay source is now subject to Recipient Verification (if configured) to prevent sending email to an
invalid user for the domain. [BNSF-20482]
Version 5.1.3.003:
Mail Processing
Enhancement: Improved Spoof Protection analysis of envelope content. [BNSF-15997]
Enhancement: Improved recipient verification performance if no Explicit Users are defined. [BNSF-19048]
Enhancement: Improved false positive detection for DLP settings. [BNSF-18738, BNSF-19321, BNSF-19946]
Enhancement: TLS can now be required for all incoming domains from the Per Domain ADVANCED > Email Protocol page.
[BNSF-19738]
Enhancement: Improved performance for tar file attachments. [BNSF-19979]
Enhancement: Improved performance for Realtime Intent Analysis. [BNSF-20002]
Fix: Attachment content filtering does not cause a spike in CPU usage. [BNSF-17216]
Fix: Appliance remains offline after a firmware upgrade if it is already in offline mode. [BNSF-18941, BNSF-19705]
Fix: Attachment filter now correctly detects video file types with altered extensions. [BNSF-18977]
Fix: Rejected mail retrieved from a POP3 server is now marked for deletion. [BNSF-19035]
Fix: Duplicate X-Barracuda-IPDD header lines are no longer added. [BNSF-19547]
Fix: Duplicate X-Barracuda-Registry header lines are no longer added. [BNSF-19829]
Fix: Improved processing performance for large multi-part text emails. [BNSF-19644]
Fix: LDAP routing will now enable alias rewriting if username/password are not set. [BNSF-19114]
Fix: SPF IPv6 record lookups work as expected. [BNSF-19500]
Fix: URL inspection now correctly handles UTF-8 characters. [BNSF-19575]
Fix: Improved process monitoring of front-end scanning engine. [BNSF-19675]
Fix: Rate control settings for POP accounts are now applied correctly. [BNSF-19745]
Fix: UID with spaces now matches white/block lists. [BNSF-19801]
Reporting
Fix: Inbound Queue details now include the To address. [BNSF-17127]
Fix: General report improvements and optimizations. [BNSF-17853, BNSF-19956, BNSF-18673, BNSF-20119]
Cloud Control
Enhancement: Rate Control and Trusted Forwarder settings are now synchronized and used by CPL unless overridden in CPL.
[BNSF-20094]
Web Interface
Fix: Message Log is no longer sorted based on the Queue Management sort. [BNSF-16315]
Fix: The Troubleshooting Telnet Utilities no longer omits the connection banner when telnetting to a mail server. [BNSF-19163]
Fix: Product Tips (see BASIC > Status page) now properly expire. [BNSF-19661]
Fix: Changing the destination mail server now takes immediate effect. [BNSF-19279]
Version 5.1.3.001
Enhancement: Per-User Allow and Block lists now check Envelope From and Header From. [BNSF-17727]
Version 5.1.2.005:
Enhancement: The Link Domains feature, configured on the BASIC > Quarantine page, and the per-domain Unify Email Aliases optio
n, configured on the USERS > LDAP Configurationpage at the domain level, are mutually exclusive and can no longer be enabled at
the same time. These settings affect how and where user quarantined mail is delivered.
Important:
No changes are automatically made to existing settings after upgrading, so make sure to verify that both of these settings are not
enabled at the same time. If both options were enabled prior to upgrading, and one is then disabled, that setting cannot be re-enabled
without disabling the other setting. Please see the online help for both settings to understand what each feature does and decide which
configuration works best for your organization. [BNSF-17401]
Enhancement: If using Single Sign-On, users can now log in with either an alias or with their primary email address. If the per-domain Un
19
ify Email Aliases option is set to Yes, then when a user logs in with an alias, that user will be directed to the primary account.
[BNSF-18377]
Fix: When an LDAP user logs into the Barracuda Spam Firewall for the first time and uses an email alias to log in, a duplicate account
will no longer be created if they already have a primary account. [BNSF-18839, BNSF-19406]
Encryption of Outbound Mail
Ability to encrypt outbound email based on policy. Requires validation of sending domains on per-domain ADVANCED > Encryptionpag
e. A notification email to the recipient provides a link to the Barracuda Message Center where the encrypted message can be retrieved.
Encryption can be selected for the following filters:
Sender domain
Sender email address
Recipient filters
Attachment filters
Content Filters
Redirection of outbound email based on policy. Email is redirected over a TLS connection to another gateway or to an encryption server
or service. Redirection can be selected for the same filters as encryption (see above).
Cloud Protection Layer
Includes the Barracuda Cloud Protection Layer, an optional cloud-based filtering layer to protect against spam and viruses. The Cloud
Protection Layer also provides email spooling to hold email in the cloud for up to 96 hours if the destination network is unavailable. This
feature is available via the Barracuda Control Center.
Mail Processing
Content Filtering: Ability to block, quarantine, encrypt or redirect messages based on content inside text-type file attachments such as
MS Office files, html, pdf or other document files.
Attachment Filtering - ability to block, quarantine, encrypt or redirect messages based on the following:
Attachment file name or file extension.
Defined attachment file types such as Microsoft Office, PDF, executables (exe) and Windows scripts (vbs).
Attachment MIME types.
Multiple Quarantine Notifications: Ability to configure more than one notification in a 24 hour period.
Reporting
New reports and reporting features:
The Traffic Summary report can print to the screen as well as being sent by email.
For use when Bayesian Filtering is turned on: False Positives report shows number of messages marked as 'Not Spam' by user
per 100 inbound emails. False Negatives report shows number of messages marked as 'Spam' by user per 100 inbound emails.
Reports can scheduled to be sent out daily, weekly or monthly.
Output formats include HTML, PDF or text.
Add-in
The Outlook add-in feature now offers an installation kit download for administrators who wish to push the add-in to users' machines with
a Windows GPO. Microsoft Exchange Server versions 2007 and 2010 are supported.
The 3.x API is no longer supported in firmware release 5.x.
Version 5.0.0.023:
APC UPS is properly supported by Barracuda Spam & Virus Firewall models 300, 400, and 800. [BNSF-12041]
Per-domain message logs now display every domain's messages in results from multiple filter searches. [BNSF-16746]
Inbound and outbound quarantine notifications can now be generated at the same time. [BNSF-16758]
SSO issue with LDAP is resolved such that users can log in without errors. [BNSF-16812]
Attachments in Microsoft Composite Document file format which are corrupt can now be extracted without errors. [BNSF-16928]
Version 5.0.0.022:
Feature: At the per-domain level, ability to specify a 'blank' LDAP search base for Active Directory. Applies when using the global catalog
port (3268) and enables searching the entire Active Directory if you have configured users for the domain outside of the domain's search
20
base.
Enhancement: Ability to block mail from IP addresses with a blank PTR (reverse DNS) record from the BLOCK/ACCEPT > Reverse DNS
page.
Enhancement: Time zone updates for Chile and Morocco.
Fix: Per-Domain Spoof Protection is correctly only blocking mail FROM the specified domain on the Barracuda Spam & Virus Firewall TO
the specified domain. [BNSF-15845]
Fix: Users can add TLD entries (e.g. info or com) to their white/black lists and properly allow/block messages accordingly. [BNSF-16587]
Fix: Inbound quarantine correctly appends Quarantine Subject Text to the subject of a message under global quarantine.
Fix: Multi-line regular expressions work correctly on the message header. [BNSF-16004]
Fix: After restoring a User Settings backup, quarantine size correctly appears as 0.00 KB on the USERS > Account View page.
[BNSF-15426]
Additional updates in 5.0.0.x:
Enhancement: Italian localization now available/selectable for end user Web interface, online help files and Outlook add-in.
Enhancement: Updated localizations for Dutch, French and Japanese.
Fix: Outbound quarantine no longer appends Quarantine Subject Text to the subject of the message, and those messages are delivered
to the Quarantine Delivery Address, if configured, instead of to the original recipient. [BNSF-16329]
Fix: BLOCK/ACCEPT > Sender Domain page now properly validates top level domains (TLDs) in Bulk Edit. [BNSF-16205]
Fix: Resolved quarantine issues.
Fix: SSL certificates no longer prevent making changes on the ADVANCED > Secure Administration page. [BNSF-16166]
Enhancement: If TLS Encryption is required per the DOMAINS > Manage Domain > ADVANCED > Email Protocol page, the
Barracuda Spam & Virus Firewall will always issue an EHLO, regardless of welcome banner containing ESMTP. [BNSF-15994]
Enhancement: Updates to Japanese help files.
Fix: User Feature overrides work with clustered systems as expected. [BNSF-14521]
Enhancement: Improved integration of Cloud Protection Layer and Barracuda Cloud Control.
Enhancement: Updates to Japanese localization.
Fix: The API password stored in the configuration database is now decrypted before matching the entry. [BNSF-15906]
Fix: The message body is correct in queued messages that are re-sent. [BNSF-15955]
Enhancement: Revised wording of HIPAA / Privacy filtering on BLOCK/ACCEPT > Content Filtering help page. [BNSF-15724]
Enhancement: Updates to French localization.
Fix: SSL Certs work as expected.
Fix: On the BASIC > Message Log page, all messages matching filter criteria are now shown when the Search button is clicked on any
page other than page 1. [BNSF-15795]
Fix: On the USERS > LDAP Configuration page at the domain level, multiple LDAP servers delimited by a space do not cause SSO
failure after upgrading to version 5.0.
Update: In Reporting, PDF format is only available for emailed reports. [117131]
Fix: Online help is now correct for the Test Encryption Connection button popup on the per-domain ADVANCED > Encryption page.
Fix: The Test LDAP button on the USERS > LDAP Configuration (domain level) page works as expected.
Fix: Whitelisted IP addresses are treated as such when using a Trusted Forwarder. [BNSF-13737]
Fix: The Certified Email registry now overrides content filtering as expected. [BNSF-15643]
Enhancement: EmailReg.org Exemptions are now entered on the BLOCK/ACCEPT > Sender Authentication page instead of on the B
LOCK/ACCEPT > Sender Domain page. [BNSF-15497]
21
Deployment Options
en
You can deploy your Barracuda Spam Firewall behind your corporate firewall or in front of your corporate firewall in the DMZ. Clustering two or
more Barracuda Spam Firewalls makes sense if your organization requires high availability, scalability, data redundancy and/or fault tolerance.
Clustering also provides centralized management of policy because once you configure one of the devices, configuration settings are
synchronized across the cluster almost immediately. Clustered systems can be geographically dispersed and do not need to be located on the
same network.
Barracuda Networks recommends reviewing and determining the best deployment option for your network before continuing with installation.
In this Section
Deployment in the DMZ
Deployment Behind the Corporate Firewall
Clustering the Barracuda Spam Firewall
Virtual Deployment
Public Cloud Hosting
22
Deployment in the DMZ
en
Barracuda Spam Firewall in the DMZ
The figure below shows the Barracuda Spam Firewall in front of your corporate firewall in the DMZ. In this example, the Mail Server has an IP
address of 64.5.5.6 and the Barracuda Spam Firewall has an internal IP address of 64.5.5.5.
Figure 1: The Barracuda Spam Firewall in the DMZ.
In this type of setup, perform the following tasks:
1. Assign an available external IP address to the Barracuda Spam Firewall.
2. Change the MX (Mail Exchange) records on the DNS (Domain Name Server) to direct traffic to the Barracuda Spam Firewall. Create an
A record and an MX record on your DNS for the Barracuda Spam Firewall.
The following example shows a DNS entry for a Barracuda Spam Firewall with a name of barracuda and an IP address of 64.5.5.5.
barracuda.yourdomain.com
IN
A
64.5.5.5
The following example shows the associated MX record with a priority number of 10:
IN MX 10 barracuda.yourdomain.com
Continue with Step 2 - Install the Barracuda Spam Firewall.
23
Deployment Behind the Corporate Firewall
en
The figure below shows the Barracuda Spam Firewall behind your corporate firewall. In this example, the Mail Server has an IP address of
10.10.10.2 and the Barracuda Spam Firewall has an IP address of 10.10.10.3.
Figure 1: The Barracuda Spam Firewall behind the corporate firewall.
In this type of setup, perform the following tasks:
1. Forward (port redirection) incoming SMTP traffic on port 25 to the Barracuda Spam Firewall at 10.10.10.3.
2. Configure the Barracuda Spam Firewall to forward filtered messages to the destination mail server at 10.10.10.2.
There is no need to modify any MX records for this type of setup.
Continue with Step 2 - Install the Barracuda Spam Firewall.
24
Clustering the Barracuda Spam Firewall
en
Clustering two or more Barracuda Spam Firewalls makes sense if your organization requires high availability, scalability, data redundancy and/or
fault tolerance. Clustering also provides centralized management of policy because once you configure one of the devices, configuration settings
are synchronized across the cluster almost immediately. Clustered systems can be geographically dispersed and do not need to be located on
the same network.
For more information about setting up a cluster of Barracuda Spam Firewalls, see:
Benefits of Clustering the Barracuda Spam Firewall - Explains features and benefits of clustering.
How to Cluster the Barracuda Spam Firewall 7.x - Steps to deploy and configure a cluster.
How to Cluster the Barracuda Spam Firewall 6.x - Steps to deploy and configure a cluster.
25
Benefits of Clustering the Barracuda Spam Firewall
en
Clustering Barracuda Spam Firewalls enables organizations to meet their high availability and fault tolerance requirements while also providing
centralized management of policy, scalability and data redundancy. Linking multiple Barracuda Spam Firewalls is easy to do with a few parameter
settings, and once you configure one of the devices, configuration settings are synchronized across the cluster almost immediately. Clustered
systems can be geographically dispersed and do not need to be located on the same network.
Centralized Policy Management
You can configure your spam, virus, and custom email delivery policies from any Barracuda Spam Firewall in the cluster – all changes are
immediately replicated to the other Barracuda Spam Firewalls in the cluster.
Alternatively, you can designate one Barracuda Spam Firewall as the “host” from which to perform administration of the cluster. To do this, you
would simply set that device to be the “Quarantine Host” and not direct any email traffic to it. There are two benefits to this configuration:
Enables you to tighten security by restricting Web interface access to only one Barracuda Spam Firewall in the cluster
Optimizes performance of the Web interface by isolating it from the impact of spikes in email volume on the network
Figure 1: Centralized policy management.
Data Redundancy and Guaranteed Configuration Updates
Quarantined messages are replicated across the cluster such that each user has a primary quarantine inbox on one Barracuda Spam Firewall
and a secondary inbox on another Barracuda Spam Firewall. This redundancy and fault tolerance ensure that all user data remains available if a
single node in the cluster fails.
Barracuda Spam Firewall clusters are also fault tolerant to temporary network failures or delays because all cluster events and updates are
queued on each node. Each individual Barracuda Spam Firewalls continues to process email independently and automatically synchronizes
quickly as network communications allow.
Federated Search
Clustering Barracuda Spam Firewalls provides you with a centralized view of all messages in a cluster through a distributed database
architecture. With federated search, you can locate any messages across the cluster by issuing a query from any single Barracuda Spam
Firewall. Unlike centralized database architectures that involve network traffic for all processed messages, this distributed database architecture
restricts network traffic to only messages returned with query results.
Figure 2: Federated search across the cluster.
26
Scalability
Because Barracuda Spam Firewall clustering leverages a distributed database architecture, it is very simple to implement and is easily scalable.
As your email traffic volume grows, you can simply add one or more additional Barracuda Spam Firewalls. Note that clustering is supported on
Barracuda Spam Firewall models 400 and higher, and each Barracuda Spam Firewall in the cluster must be the same model number.
Secure Access and Data Transmission
Barracuda Spam Firewall clustering utilizes encrypted and secure communications for user access, message replication and configuration
synchronization across the cluster.
Limiting User Access
As mentioned above, you can choose to dedicate one Barracuda Spam Firewall on the cluster as the “Quarantine Host” to limit users’ access to
that node when checking their quarantine inboxes. In this configuration, quarantine notifications from all Barracuda Spam Firewalls in the cluster
will direct users to that Quarantine Host, and you would direct all email to the other nodes on the cluster.
Data transmission is always encrypted through SSL communication between Barracuda Spam Firewalls in the cluster. Secure communication is
controlled over defined TCP ports.
Restricted Access to Configuration
Transmission of configuration data between devices on the cluster is secured by a shared password, or “shared secret”, which the administrator
creates and assigns to every Barracuda Spam Firewall. This prevents access to configuration parameters from other Barracuda Spam Firewalls
outside the cluster or other network devices.
To cluster Barracuda Spam Firewalls
Deploying clustered Barracuda Spam Firewalls is easy with the step-by-step instructions documented in the user interface. Every Barracuda
Spam Firewall in a cluster must be the same model and have the same version of firmware installed. For complete detailed instructions in the
Barracuda TechLibrary, see How to Cluster the Barracuda Spam Firewall.
Directing Email to the Cluster: Load Balancing
You can load balance incoming email directed to a cluster of Barracuda Spam Firewalls in one of two ways:
1. Use a Barracuda Load Balancer to direct email into the cluster. The Barracuda Load Balancer can distribute traffic based on weighted
round-robin, weight least connections, or adaptive scheduling methods that query each Barracuda Spam Firewall for load and distribute
traffic accordingly.
2. Configure multiple DNS MX records. Generally, MX record load balancing will not distribute the traffic as evenly as a dedicated load
balancer.
27
How to Cluster the Barracuda Spam Firewall 7.x
en
Note that clustered systems can be geographically dispersed and do not need to be located on the same network. Important: Every
Barracuda Spam Firewall in a cluster must meet the following requirements:
Be the same model (400 and above).
Have the same version of firmware installed.
Be configured for the same time zone.
Have a unique external IP address. This means that every Barracuda Spam Firewall behind a NAT must have a unique
external IP address and must be reachable by that external IP address.
When replacing a failed system in a cluster, be sure to follow step #3 as described below under Removing a Barracuda Spam
Firewall From a Cluster.
Set Up Clustered Systems
To cluster two Barracuda Spam Firewalls together, where one system is designated as "Barracuda1" and the other is designated "Barracuda2",
do the following:
1. Complete the installation process for each system as described in Step 2 - Install the Barracuda Spam Firewall. Each Barracuda Spam
Firewall in a cluster must be the same model# and be on exactly the same firmware version.
2. From the ADVANCED > Task Manager page on the Barracuda1 system, verify that no processes are running. Complete this step for the
Barracuda2 system as well. No processes should be running when you add a system to a cluster.
3. Configure the Barracuda2 system as you would like Barracuda1, and any other system you might add to the cluster, to be configured.
Make a backup of the configurations of each Barracuda Spam Firewall.
4. From the ADVANCED > Clustering page on the Barracuda1 system, enter a Cluster Shared Secret password for the cluster, and click
Save.
5. Optional: In the Cluster Hostname field on Barracuda1, enter the DNS/hostname (FQDN) by which other Barracuda Spam Firewalls in
the cluster will attempt to communicate with this one. If this field is left blank, the IP address entered below will be used. This field is also
useful for limiting user access to a cluster - see Limiting Access to a Cluster below.
6. From the ADVANCED > Clustering page on the Barracuda2 system, do the following:
a. Enter the same Cluster Shared Secret password, and click Save.
b. Optionally enter the DNS/hostname (FQDN) in the Cluster Hostname field for Barracuda2.
c. In the Clustered Systems section, enter the IP address of the Barracuda1 system and click Join Cluster. At this point, the
configuration of the Barracuda1 system will automatically propagate to Barracuda2.
7. On each Barracuda system, refresh the ADVANCED > Clustering page, and verify that:
a. Each system’s IP address appears in the Clustered Systems list
b. The Connection Status of each server is green - see Figure 1 below.
8. Distribute the incoming mail traffic to each Barracuda Spam Firewall using a Barracuda Load Balancer (preferred) or another load
balancing device, or by using multiple DNS MX records of equal priority.
Figure 1: Two servers in a cluster with a 'green' status.
Add a Barracuda Spam Firewall to a Cluster
Begin by making a backup of the configuration of any system in the cluster, then perform these steps on the Barracuda Spam Firewall you want
to add to the existing cluster:
1. Complete the installation process and ensure that the new Barracuda Spam Firewall is the same model# and running the same firmware
version as all systems in the cluster.
2. From the ADVANCED > Task Manager page, verify that no processes are running. Do this on all other systems in the cluster as well.
3. From the ADVANCED > Clustering page, enter the Cluster Shared Secret password for the cluster, and click Save.
4. Optional: In the Cluster Hostname field, enter the DNS/hostname (FQDN) by which other Barracuda Spam Firewalls in the cluster will
attempt to communicate with this one.
5. On a Barracuda Spam Firewall already in the cluster, change any value in the configuration and click Save. This ensures proper
synchronization of the configuration.
6.
28
6. On the ADVANCED > Clustering page on the new Barracuda Spam Firewall to be added to the cluster, enter the IP address of any
system in the cluster in the Add System field and click the Join Cluster button. At this point, the configuration of the cluster will
automatically propagate to the newly added system.
Limiting End-user Access to the Cluster
You can choose to dedicate a single Barracuda Spam Firewall as the Quarantine Host to serve up the end-user interface through which users
will access their quarantine inboxes, even though their actual quarantine inbox (primary or secondary) may be hosted by another Barracuda
Spam Firewall in the cluster. By not directing email to the Quarantine Host, you can:
Enhance network security by limiting end-user access (port 8000 by default) and administration to only one Barracuda Spam Firewall on
the Internet
Insulate the user interface performance from any peaks in email volume
To configure one Barracuda Spam Firewall as the Quarantine Host, from the BASIC > Quarantine page, enter that system's hostname in the Qu
arantine Host field.
Removing a Barracuda Spam Firewall From a Cluster
1. Log into the system to be removed and change or clear the Cluster Shared Secret on the ADVANCED > Clustering page. Click Save
Changes. Changing the cluster shared secret prevents the systems in the cluster from communicating with one another.
2. On the same system, delete all other systems from the Clustered Systems list.
3. On any system that remains in the cluster, go to the ADVANCED > Clustering page. In the Clustered Systems list, delete the system
to be removed from the cluster. This step is very important when removing a failed Barracuda Spam Firewall from a cluster.
Centralized Policy Management With a Quarantine Host
You can optionally designate one Barracuda Spam Firewall as the "host" of the cluster such that all administration of configuration settings and
access to per-user quarantine for the cluster can only be accessed and set from that node. This option has two advantages: it provides for
additional security by limiting access to administration of the cluster, and it protects the user interface from mail processing load since, with this
configuration, you do not direct any email traffic to the host node.
To assign one Barracuda Spam Firewall as the host of the cluster, enter the hostname of that device in the Quarantine Host field on the BASIC >
Quarantine page and do not direct any email to that device.
Redundancy of user quarantine data on the cluster
Each user account has a primary and backup server in the cluster. Regardless of how many Barracuda Spam Firewalls there are in the cluster,
there are always two appliances that have the same quarantine information (configuration and quarantine messages).
Data Not Synchronized Across the Cluster
Clustering provides 100% redundant coverage of the propagated data. However, for practical reasons, some data is not propagated to the other
clustered systems when a new system joins. Energize updates do not synchronize across systems in a cluster. The following Barracuda Spam
Firewall configurations are considered unique and will not sync to match other Barracuda Spam Firewalls in a cluster:
IP Address, Subnet Mask, and Default Gateway (on the BASIC > IP Configuration page)
Primary DNS Server and Secondary DNS Server (on the BASIC > IP Configuration page)
Serial number (this will never change)
Hostname (on the BASIC > IP Configuration page)
Any advanced IP configuration (Barracuda Spam Firewall 600 and above, on the ADVANCED > Advanced Networking page)
Administrator password
Guest password
Time Zone (on the BASIC > Administration page)
Cluster hostname (on the ADVANCED > Clustering page)
Cluster Shared Secret, though this must be the same for the cluster to work properly (on the ADVANCED > Clustering page)
Local Host Map (on the ADVANCED > Clustering page)
SMTP Welcome Banner (on the ADVANCED > Email Protocol page)
SMTP Port (on the BASIC > Outbound page)
Web Interface HTTP Port (on the BASIC > Administration page)
Web Interface HTTPS/SSL port (on the ADVANCED > Secure Administration page)
Any other secure administration configuration, including saved certificates (on the ADVANCED > Secure Administration page)
Quarantine Host (on the BASIC > Quarantine page)
All SSL/TLS information, including saved certificates (on the ADVANCED > Secure Administration page)
Whether to only display local messages in the message log (Only view local messages on the BASIC > Message Log > Preferences pa
ge)
Whether the latest release notes have been read
All customized branding (Barracuda Spam Firewall 600 and above, on the ADVANCED > Appearance page)
29
en
See also: Benefits of Clustering the Barracuda Spam Firewall
When replacing a failed system in a cluster, be sure to follow step #3 as described below under Removing a Barracuda Spam
do the following:
4. From the ADVANCED > Clustering page on the Barracuda1 system, enter a Cluster Shared Secret password for the cluster, and click
Save Changes.
a. Enter the same Cluster Shared Secret password, and click Save Changes.
3.
30
3. From the ADVANCED > Clustering page, enter the Cluster Shared Secret password for the cluster, and click Save Changes.
5. On a Barracuda Spam Firewall already in the cluster, change any value in the configuration and click Save Changes. This ensures
proper synchronization of the configuration.
Limiting End-user Access to the Cluster
the Internet
Removing a Barracuda Spam Firewall From a Cluster
3. On any system that remains in the cluster, go to the ADVANCED > Clustering page. In the Clustered Systems list, delete the system
to be removed from the cluster. This step is very important when removing a failed Barracuda Spam Firewall from a cluster.
Guest password
SMTP Port (on the BASIC > Outbound page)
31
ge)
32
en
See also: Benefits of Clustering the Barracuda Spam Firewall
Important
When replacing a failed system in a cluster, be sure to follow step #3 as described below under How to Remove a Barracuda Spam
do the following:
4. From the ADVANCED > Clustering page on the Barracuda1 system, enter a Shared Secret password for the cluster, and click Save
Changes.
a. Enter the same Shared Secret password, and click Save Changes.
3.
33
3. From the ADVANCED > Clustering page, enter the Cluster Shared Secret password for the cluster, and click Save Changes.
5. On a Barracuda Spam Firewall already in the cluster, change any value in the configuration and click Save Changes. This ensures
proper synchronization of the configuration.
Secure the Cluster by Limiting End-user Access
the Internet
How to Remove a Barracuda Spam Firewall From a Cluster
3. On any system that remains in the cluster, go to the ADVANCED > Clustering page. In the Clustered Systems list, delete the system to
be removed from the cluster. This step is very important when removing a failed Barracuda Spam Firewall from a cluster.
Guest password
34
ge)
The Explicit Users To Accept For list, if enabled and used, on the ADVANCED > Explicit Users page. This is a global setting.
The Valid Recipients list on the DOMAINS > Manage Domain > USERS > Valid Recipients page. This is a per-domain setting.
35
Virtual Deployment
en
Requirement
This virtual appliance requires a 64-bit capable host.
The Barracuda Spam Firewall manages all inbound and outbound email traffic to protect organizations from email-borne threats and data leaks. It
includes the following features:
Secures inbound email traffic against inbound malware, spam, phishing, and Denial of Service attacks.
Offloads compute-intensive tasks to the cloud, like antivirus and DDoS filtering, to reduce processing load on the appliance and ensure
threats never reach the network perimeter.
Spools email for up to 96 hours using the Cloud Protection Layer, with an option to redirect traffic to a secondary server.
Ensures that every outbound email complies with corporate DLP policies using outbound filtering and quarantine capabilities.
Barracuda recommends reading Understand the Concepts before continuing with deployment.
Deploying Your Barracuda Spam Firewall Vx
Complete the following steps to deploy your Barracuda Spam Firewall Vx:
1.
2.
3.
4.
Deploy the Barracuda Spam Firewall Vx image.
Allocate the cores, RAM, and hard disk space for your Barracuda Spam Firewall Vx.
Set up the Barracuda Spam Firewall Vx with the Vx Quick Start Guide.
Route email to the Barracuda Spam Firewall Vx.
Managing Your Virtual Machine
Backing Up Your Virtual Machine System State
36
How to Deploy Barracuda Spam Firewall Vx Images
en
Barracuda offers the following types of images for the Barracuda Spam Firewall Vx deployment. Follow the instructions for your hypervisor to
deploy the Barracuda Spam Firewall Vx appliance.
Image Type
Supported Hypervisors
OVF
VMware ESX and ESXi (vSphere Hypervisor) versions 4.x
VMWare ESX and ESXi (vSphere Hypervisor) versions 5.x
Sun/Oracle VirtualBox and VirtualBox OSE version 3.2
VMX
VMware Server 2.x
VMWare Workstation 6.x, Player 3.x, and Fusion 3.x
XVA
Citrix XenServer 5.5+
VHD
Microsoft Hyper-V 2008 R2 and 2012
30 Day Evaluation
1. Visit https://www.barracuda.com/purchase/evaluation.
2. Choose the Barracuda Spam Firewall.
3. Download the image for your hypervisor from the Barracuda Virtual Appliance Download page. After the download is complete,
extract the files from the ZIP folder.
4. Deploy the virtual appliance image as described below. The procedure varies depending on your hypervisor.
Deploy OVF Images
VMware ESX and ESXi 4.x
Use the OVF file ending in -4x. ovf for this hypervisor .
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Download and expand the Barracuda Spam Firewall Vx ZIP folder.
From the File menu in the vSphere Client, select Deploy OVF Template.
Select Import from file, navigate to the extracted folder, and locate the Barracuda Spam Firewall Vx OVF file. Click Next.
Review the appliance information and End User License Agreement, and enter a name for the virtual appliance. Click Next.
Select the resource pool for your virtual appliance. Click Next.
Select a datastore and disk formats. Click Next.
Click Finish.
Follow the recommendations in Allocating Cores, RAM, and Hard Disk Space for Your Barracuda Spam Firewall Vx.
On the Virtual Machines tab, right-click the Barracuda Spam Firewall VM that you created. Select Power > Power On to run it.
Follow the Barracuda Spam Firewall Vx Quick Start Guide instructions to set up your virtual appliance.
VMware ESX and ESXi 5.x
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Launch vSphere Client and select the appropriate host and resource pool.
From the File menu in the vSphere Client, select Deploy OVF Template.
Click Browse, navigate to the extracted folder, and select the Barracuda Spam Firewall Vx OVF file. Click Next.
Verify that you are installing the correct Barracuda virtual appliance. Click Next.
Review the End User License Agreement and click Accept. Click Next.
Enter a name for the virtual appliance. Click Next.
Select the destination storage for the virtual machine. Click Next.
Select a disk format. To ensure maximum stability when deploying your Barracuda Vx appliance, specify the disk format as Thick
Provision Eager Zeroed. Click Next.
Map the network to the target network for this virtual appliance. Click Next.
Review the deployment options. Click Finish to deploy the virtual appliance.
Locate the appliance within the appropriate virtual machine and resource pool. Select it and power it on by clicking the green arrow.
Click the Console tab. You can monitor the appliance as it is prepared for use.
Sun/Oracle VirtualBox and VirtualBox OSE 3.2
1.
37
1.
2.
3.
4.
5.
From the File menu in the VirtualBox client, select Import Appliance.
Navigate to the extracted folder and locate the Barracuda Spam Firewall Vx OVF file.
Select the file and click Next.
On the Import Settings screen, follow the recommendations in Allocating Cores, RAM, and Hard Disk Space for Your Barracuda Spam
Firewall Vx. Click Finish.
6. Start the appliance.
7. Follow the Barracuda Spam Firewall Vx Quick Start Guide instructions to set up your virtual appliance.
Deploy VMX Images
VMware Server 2.x
Use the .vmx and .vmdk files for this hypervisor .
1. Download and expand the Barracuda Spam Firewall Vx ZIP folder.
2. Navigate to the extracted folder and move the files ending in .vmx and .vmdk into a folder in your datastore (which you can locate from
the Datastores list on your server's summary page).
3. From the VMware Infrastructure Web Access client's Virtual Machine menu, select Add Virtual Machine to Inventory.
4. Navigate to the folder in your datastore used in step 2 and select the file ending in .vmx. Click OK.
5. Follow the recommendations in Allocating Cores, RAM, and Hard Disk Space for Your Barracuda Spam Firewall Vx.
6. Start the appliance.
VMware Workstation 6.x, Player 3.x, and Fusion 3.x
Use the .vmx file for this hypervisor.
1.
2.
3.
4.
5.
6.
7.
From the File menu, select Open a Virtual Machine.
Navigate to the extracted folder and select the file ending in .vmx.
Use the default settings and click Finish.
Start the appliance.
Deploy XVA Images
Citrix XEN Server 5.5+
Use the .xva file for this hypervisor. For XEN Server, you first import the virtual appliance template and then create a new virtual appliance based
on that template.
Step 1. Import the virtual appliance template:
2. From the File menu in the XenCenter client, select Import.
3. Click Browse, navigate to the extracted folder, and select the file ending in .xva. Click Next.
4. Select a server for the template. Click Next.
5. Select a storage repository for the template. Click Import.
6. Select a virtual network interface for the template. Click Next.
7. Review the template settings. Click Finish to import the template.
Step 2. Create a new virtual appliance:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Right-click the virtual appliance template and select New VM wizard.
Select the virtual appliance template. Click Next.
Enter a name for the virtual appliance. Click Next.
For the DVD drive, select <empty>. Click Next.
Select a home server. Click Next.
Specify the number of virtual CPUs and memory for the virtual appliance. Follow the recommendations in Allocating Cores, RAM, and
Hard Disk Space for Your Barracuda Spam Firewall Vx. Click Next.
Select a virtual disk. Click Next.
Select a virtual network interface. Click Next.
Review the virtual appliance settings. Click Create Now.
When the virtual appliance is ready, right-click it and then click Start.
Deploy VHD Images
Microsoft Hyper-V 2008 R2 and 2012
38
Use the .vhd file for this hypervisor.
If you are running Microsoft Windows Server 2012 (not Windows Server 2012 R2), launch the WinServerSetup.bat file located
in the extracted folder. This batch file corrects a compatibility issue and takes about a minute to run. If the WinServerSetup.bat
file is not included in your virtual appliance folders, you can download the file from here: https://copy.com/lV9i848iYLIuY27w.
Copy the file to the top level folder (where the license, manifest, and readme files are located). Note that the WinServerSetup.b
at file supersedes the WinServer2012Setup.bat file. If you have issues with the installation, contact Barracuda Networks
Technical Support. If you are running any other version of Windows Server, this step is unnecessary.
2. Navigate to the extracted folder and verify that the HyperV folder contains the following subfolders:
Virtual Machines
Virtual Hard Disks
Snapshots
3. In Hyper-V Manager, right-click your VM host and select Import Virtual Machine.
4. Navigate to the extracted folder, select the HyperV folder, and click Select Folder.
5. Select the Copy the virtual machine and Duplicate all files. Click Import.
6. Follow the recommendations in Allocating Cores, RAM, and Hard Disk Space for Your Barracuda Spam Firewall Vx.
7. Start the Barracuda Spam Firewall Vx by right-clicking the virtual machine and selecting Start.
To take advantage of Microsoft's VHDX support on Hyper-V 2012 and 2012 R2, follow the instructions in How to Convert and Replace
a Barracuda Virtual Appliance VHD File with a VHDX Format File.
39
Allocating Cores, RAM, and Hard Disk Space for Your Barracuda Spam Firewall Vx
en
Barracuda recommends the following settings for the initial deployment of your virtual appliance or when upgrading existing
installations.
Cores, RAM, and Hard Disk Space for the Barracuda Spam Firewall Vx
Model
Cores - Maximum
RAM - Recommended
Minimum
Hard Disk - Recommended
Minimum
100
1
2.5 GB
50 GB
300
2
5 GB
50 GB
400
3
8 GB
50 GB
600
4 or more(1)
10 GB
200 GB
Note:
(1)
You can add up to 10 cores to your Barracuda Spam Firewall 600 Vx. The number of cores available is limited only by license. Add an
additional 2.5 GB of RAM for each additional core. Also plan to add additional hard disk space (at least 500 GB for 5 or more cores).
Allocating Cores
In your hypervisor, specify the number of cores to be used by the Barracuda Spam Firewall Vx. Each Barracuda Spam Firewall Vx model can use
only the number of cores specified in the table above. For example, if you assign 6 cores to the Barracuda Spam Firewall 300 Vx (which supports
only 2 cores), the hypervisor disables the 4 extra cores that cannot be used.
To add cores to your appliance:
1. Shut down the Barracuda Spam Firewall Vx in your hypervisor.
2. In the virtual machine CPU settings, add cores.
Your hypervisor license and version might limit the number of cores that you can specify for your appliance. In some cases, you must
add cores in multiples of two.
Allocating Hard Disk Space
Barracuda requires a minimum of 50 GB of hard disk space to run your Barracuda Spam Firewall Vx. From your hypervisor, you can specify the
size of the hard disk or add a hard disk.
To specify the allocated hard disk space or add a hard disk to your appliance:
1.
2.
3.
4.
Shut down the Barracuda Spam Firewall Vx in your hypervisor.
Take a snapshot of the virtual machine.
In the virtual machine settings, specify the new size for the hard disk or add a new hard disk.
Restart the virtual machine. As the appliance is booting up, view the console for Barracuda Spam Firewall Vx. When the blue Barracuda
console screen appears and asks if you want to use the additional hard disk space, enter Yes.
If you do not respond to the prompt in 30 seconds, the answer defaults to No . Resizing can take several minutes, depending on the
amount of hard disk space specified.
40
41
Barracuda Spam Firewall Vx Quick Start Guide
en
To set up your Barracuda Spam Firewall Vx, complete the following steps:
en
Before You Begin
Step 1. Open Firewall Ports
Step 2. Configure the Network Settings
Step 3. Enter the License Token
Step 4. Log Into the Appliance Web Interface and Verify the Configuration
Step 5. Update the Firmware
Step 6. Change the Administrator Password
Step 7. Verify the Barracuda Spam Firewall Vx Configuration
Next Step
Before You Begin
Deploy the Barracuda Spam Firewall Vx on your hypervisor. You only need a single virtual NIC on your virtual appliance.
Step 1. Open Firewall Ports
If your Barracuda Spam Firewall Vx is located behind a firewall, open the following ports to ensure proper operation:
Port
Direction
TCP
UDP
Usage
25
In/Out
Yes
No
Email and email bounces
53
Out
Yes
Yes
Domain Name Service
(DNS). Verify that the
DNS servers can resolve
updates.cudasvc.com
.
80
Out
Yes
No
Virus, firmware, and
spam rule updates
123
Out
No
Yes
Network Time Protocol
(NTP)
443
Out
Yes
No
HTTPS/SSL port used for
initial VM provisioning
and access to updates.
cudasvc.com*
*You can disable the initial provisioning port after the initial provisioning process is complete.
When deploying the Barracuda Spam Firewall Vx, you must also configure your firewall to allow ICMP traffic from the Barracuda Spam Firewall
Vx to outside servers.
Step 2. Configure the Network Settings
For your Barracuda Spam Firewall Vx to work, it needs to be able to communicate with other devices on your organization's network. It also must
be able to communicate with Barracuda Networks for license verification, firmware updates, and spam and virus definition updates.
To configure the network settings, complete the following steps:
1.
2.
3.
4.
5.
In your hypervisor client, start your virtual appliance.
Open the console for the Barracuda Spam Firewall Vx.
When the login prompt appears, log in as admin with the password admin.
Navigate to TCP/IP Configuration.
Enter the following IPv4 addresses:
IP Address - This IP address identifies the Barracuda Spam Firewall Vx to your organization's network.
Netmask - The sub-network mask (subnet mask or netmask) provides a simple way to limit which other devices on the network
can access the Barracuda Spam Firewall Vx directly.
Default Gateway - The default gateway is the internal network device the Barracuda Spam Firewall Vx connects to to reach the
parts of the internal network it cannot access directly within its subnet.
Primary DNS Server - The primary domain name system (DNS) server contains a database of network device names and their
corresponding Internet address hosts. DNS servers allow you to identify devices by name instead of by address.
42
Secondary DNS Server - The secondary DNS server acts as a backup to the primary.
You can edit these fields later on the BASIC > IP Configuration page in the product web interface.
Step 3. Enter the License Token
Once your Barracuda Spam Firewall Vx has network access, you can provision it You need your Barracuda Vx license token, which you received
via email or from the Barracuda Networks website when you downloaded the Barracuda Spam Firewall Vx ZIP folder. The license token is a 15
character string, formatted like this: 01234-56789-ACEFG.
You can also get a license token by requesting an evaluation on the Barracuda website at http://www.barracuda.com/purchase/evaluation.
To enter your license token, complete the following steps:
1. Navigate to Licensing and enter your Barracuda License Token and default domain to complete provisioning.
2. Navigate to Save Changes and press Enter. The virtual appliance reboots.
3. After the virtual appliance has finished rebooting, go to http://<your ip>:8000 to access the web interface and finalize configuration.
Step 4. Log Into the Appliance Web Interface and Verify the Configuration
Log into the Barracuda Spam Firewall Vx web interface, and finalize the configuration of the appliance:
1. In your web browser, go to https://<configured IP address for the Barracuda Spam Firewall>:8000
2. Log into the Barracuda Spam Firewall Vx web interface as the administrator:
Username: admin Password: admin
3. Go to the BASIC > IP Configuration page and verify that the following settings are correct:
IP Address
Subnet Mask
Default Gateway
Primary DNS Server
Secondary DNS Server
4. Enter the Server Name/IP of the destination email server where you want the Barracuda Spam Firewall Vx to deliver mail.
For example: type: mail.<yourdomainname>.com
5. Enter the Default Hostname.
For example: <yourhost>
The host name is added to bounce messages.
6. Enter the Default Domain.
For example: <yourcompanydomain.com>
The domain is added to bounce messages and reports.
7. Under Allowed Email Recipient Domain(s), enter each domain for which you want the Barracuda Spam Firewall Vx to receive email.
The Barracuda Spam Firewall Vx rejects all incoming email that is addressed to domains that are not specified here.
Step 5. Update the Firmware
The product Firmware is the software running all of the features and functions on the Barracuda Spam Firewall Vx.
Firware Update
Firmware updates always require a reboot of the Barracuda Spam Firewall Vx. To minimize interruptions, Barracuda Networks
recommends updating the firmware after peak business hours.
Go to the ADVANCED > Firmware Update page. Compare the Current Installed Version to the Latest General Release. If there is a new Late
st General Release available, perform the following steps to update the system firmware:
1. Click Download Now next to the firmware version that you want to install. To view the download progress, click Refresh. When the
download is complete, the Refresh button is replaced by the Apply Now button.
2. Click Apply Now to install the firmware. The firmware installation takes several minutes to complete.
After the firmware is applied, the Barracuda Spam Firewall Vx automatically reboots. The login page is displayed when the system
comes back up.
3. Log back into the web interface and read the Release Notes to learn about enhancements and new features. It is also good practice to
verify settings that you have already entered, because new features might have been included with the firmware update.
For more information, see Product Activation and Update Firmware.
Step 6. Change the Administrator Password
To prevent unauthorized use, change the default administrator password to a more secure password. Go to the BASIC > Administration page,
43
enter your old and new passwords, and click Save Password. This changes the administrator password for the web interface.There is also a
separate administrator account for the console. This password can be changed as well by navigating to System and entering the old and new
passwords.
Step 7. Verify the Barracuda Spam Firewall Vx Configuration
After you install your Barracuda Spam Firewall Vx and configure your firewall, you can test the configuration. Go to the ADVANCED >
Troubleshooting page. In the Network Connectivity Tests section, enter updates.cudasvc.com in the Ping Device box and click Begin
Ping. The Barracuda Spam Firewall sends ping packets to the updates.cudasvc.com server. The results are displayed in a popup window. If
your Vx is able to transmit and receive all of the ping packets without packet loss, your virtual appliance is configured correctly to access the
Internet.
Next Step
Your Barracuda Spam Firewall Vx is now activated, able to send and receive network traffic, and is running the latest firmware. You're ready to
begin setting up the Vx to filter spam, viruses, malware, and spyware from incoming email. To begin this configuration, go to Configure the Web
Interface .
44
Route Email to the Barracuda Spam Firewall Vx
en
There are two common options for routing email to the Barracuda Spam Firewall Vx:
Port Forwarding: Change the port forwarding settings on your corporate firewall to route incoming email to your Barracuda Spam Firewall
Vx.
MX Records: Create a DNS entry for your Barracuda Spam Firewall Vx and change your DNS MX record to route incoming email to the
Barracuda. Typically, this is done at your DNS server or through your DNS service.
Example: DNS Entry for Barracuda Spam Firewall barracuda.barracudanetworks.com IN A 66.233.233.88
Example: Modified MX Record IN MX 10 barracuda.barracudanetworks.com
Note: some DNS servers cache information for up to 7 days, so it may take time for your email to be routed to the new MX record. To route
OUTGOING mail through the Barracuda Spam Firewall Vx, you must configure Outbound Relay operation on the ADVANCED > Outbound pag
e.
45
Backing Up Your Virtual Machine System State
en
en
Virtual machine environments generally provide a snapshot capability, which captures the state of a system as it's running. Once a snapshot is
created, you can perform additional operations on the system and revert to the snapshot in the case of disaster recovery (or for any other
reason). Because this feature is so powerful, Barracuda strongly recommends performing a snapshot at certain points in time:
Before upgrading the Barracuda product firmware.
Before making major changes to your configuration (this makes taking a snapshot a convenient undo mechanism).
After completing and confirming a large set of changes, such as initial configuration.
As a periodic backup mechanism.
Before taking a snapshot, Barracuda strongly recommends powering off the virtual machine. This step is particularly important if you
are using Microsoft Hyper-V as your virtual machine environment.
Barracuda Networks recommends that you review your virtual environment documentation regarding the snapshot capabilities and be familiar
with their features and limitations.
46
Public Cloud Hosting
en
The Barracuda Spam Firewall manages all inbound and outbound email traffic to protect organizations from email-borne threats and data leaks.
As a complete email management solution, organizations can encrypt messages and leverage the cloud to spool email if mail servers become
unavailable. For more information about the Barracuda Spam Firewall, see Barracuda Spam Firewall - Overview. Cloud hosting of the Barracuda
Spam Firewall virtual machine is currently supported on:
Amazon Web Services (AWS)
Microsoft Azure
VMware vCloud Air Deployment
47
Amazon Web Services
en
Follow instructions below to purchase or get an evaluation of the Barracuda Spam Firewall on Amazon Web Services. After purchasing or
obtaining an evaluation through Amazon, continue with How to Deploy the Barracuda Spam Firewall on Amazon Web Services.
Before you begin
1. Create an Amazon Web Services account.
2. Create a Virtual Private Cloud (VPC) on Amazon Web Services. See Creating a VPC, Internet Gateway and Subnet.
3. Choose either the BYOL or Hourly/Metered licensing option:
Bring Your Own License (BYOL) – This option involves first obtaining a Barracuda Spam Firewall license token, either by:
Providing the required information for a free evaluation at https://www.barracuda.com/purchase/evaluation OR
Purchasing online at https://www.barracuda.com/purchase/ . With this license option, there will be no Barracuda Spam Firewall
Software charges, but Amazon Elastic Compute Cloud (Amazon EC2) usage charges on Amazon will be applicable.
Barracuda offers the same three models for both the Hourly/Metered and BYOL options as shown below. After obtaining your license
token, visit the AWS Marketplace to continue the process.
Hourly / Metered – In this licensing option, you complete the purchase/evaluation of the Barracuda Spam Firewall entirely within the AW
S Marketplace. Once the instance is launched, it will be provisioned automatically. In this option, you will be charged hourly for both the
Barracuda Spam Firewall Software and Amazon Elastic Compute Cloud (Amazon EC2) usage on Amazon. For pricing information,
see the AWS Marketplace. Barracuda offers the same three models for both the Hourly/Metered and BYOL options as shown below.
Barracuda Spam Firewall Virtual Appliance Instance Types on AWS
The table below lists the available Barracuda Spam Firewall virtual appliance models, the corresponding Instance Type to be used in Amazon
Web Services and the default CPU and Memory for the instance. You'll select the Instance Type in the next step in How to Deploy the Barracuda
Spam Firewall on Amazon Web Services.
Barracuda Spam Firewall
Model
Supported Instance Type in
Amazon Web Services
vCPU
Memory
BSF Cloud Edition – Level 3
m1.medium, m3.medium
1
3.7 GB
m1.large, m3.large
2
7.5 GB
m1.xlarge, m3.xlarge
4
15 GB
Important
If you need to add additional storage space after deployment, due to the Amazon Web Services (AWS) structure, the only current
option is to redeploy and restore the configuration on a larger instance.
Next Step
Continue with How to Deploy the Barracuda Spam Firewall on Amazon Web Services for instructions on installation and configuration.
48
How to Deploy the Barracuda Spam Firewall on Amazon Web Services
en
The Barracuda Spam Firewall can be deployed as a virtual appliance in the Amazon cloud. To launch a Barracuda Spam Firewall
using Amazon Web Services, follow the steps in this guide to upload the Barracuda Spam Firewall virtual appliance using your
existing Amazon Web Services account. Then, continue with the Barracuda Spam Firewall Quick Start Guide for Amazon Web
Services for licensing and initial configuration of your virtual appliance. Amazon Web Services charges apply. For more information,
see Amazon's monthly pricing calculator at http://calculator.s3.amazonaws.com/calc5.html.
Create a Persistent Public IP Address for Your Barracuda Spam Firewall
When an instance of your Barracuda Spam Firewall appliance is created, a public IP address is associated with the instance. However, this IP
address can change if the instance is stopped. To create a persistent IP address, see Configuring an Elastic IP Address for an Instance.
Launch the Barracuda Spam Firewall Instance on Amazon Web Services
1. From the Amazon Web Services (AWS) Management Console:
a. Log into the AWS Management Console and open the Amazon EC2 console at https://console.aws.amazon.com/ec2/.
b. From the top right corner of the page, select the region for the instance. This is important because some Amazon EC2 resources
can be shared between regions.
2. Click Launch Instance.
3. In Step 1: Choose an Amazon Machine Image (AMI) page, select AWS Marketplace and search for the Barracuda Spam Firewall AMI
. Click Select next to the Barracuda Spam Firewall AMI.
4. In Step 2: Choose an Instance Type page, select an instance type from the All Instance types or General purpose table. Click Next:
Configure Instance Details to continue.
See the Amazon Web Services article to verify the recommended instance type for your Barracuda Spam Firewall sizing.
Select the recommended instance type. Important: If you need to add additional storage space after deployment, due to the
Amazon Web Services (AWS) structure, the only current option is to redeploy and restore the configuration on a larger
instance.
49
5. In Step 3: Configure Instance Details page:
a. Enter the Number of instances you want to launch.
b. Select the appropriate Network from the list.
c. Select the appropriate Subnet from the list, or keep the default subnet.
d. In the Advanced Details pane, keep the default setting for all parameters and click Next: Add Storage.
6. In Step 4: Add Storage page, the table displays the storage device settings for the instance. Modify the values if required and click Next
: Tag Instance.
50
7. In Step 5: Tag Instance page, add/remove the tags for the instance (if required).
8. In Step 6: Configure Security Group page, choose Select an existing security group to select and assign the security group(s) from
the existing list, or choose Create a new security group to create a new group (refer to Creating a Security Group on Amazon Web
Services for more information). Click Review and Launch.
By default, the Barracuda Spam Firewall web interface listens on port 8000 for HTTP and port 443 for HTTPS. Make sure
these ports (8000 and 443) are added to the Inbound Rule of the security group associated with the Barracuda Spam Firewall.
Additionally, in order to be notified of any virtual appliance (re)boots due to initial installation, system upgrades, instance
changes or other administrative reasons, make sure to add port 40080 to the set of security groups. Also add the port(s)
through which you configure the Service(s) for this instance.
51
9. In Step 7: Review Instance Launch page, review your settings before launching the instance, and then click Launch.
Amazon Web Services now provisions the Barracuda Spam Firewall. Allow a few minutes for the Amazon Web Services Agent and the
Barracuda Spam Firewall virtual machine to boot up.
DO NOT restart the Barracuda Spam Firewall while it is launching.
Continue with Barracuda Spam Firewall Quick Start Guide for Amazon Web Services to license and configure your virtual appliance.
52
Barracuda Spam Firewall Quick Start Guide for Amazon Web Services
en
Make sure you have completed the steps in the article How to Deploy the Barracuda Spam Firewall on Amazon Web Services before
continuing with the instructions below.
The Licensing of the Barracuda Spam Firewall after launching on Amazon Web Services (AWS) section is not required when the
Barracuda Spam Firewall is deployed using Hourly / Metered licensing option. You can skip to the Verify Configuration and Change
the Password section.
Licensing of the Barracuda Spam Firewall after launching on Amazon Web Services (AWS)
After launching the Barracuda Spam Firewall on the Amazon Web Services, the next step is licensing. To complete the licensing and provisioning
of your Barracuda Spam Firewall:
1. Sign in to the Amazon Web Services Portal.
2. Open the EC2 Management Console, and then click Instances.
3. In the Instances table, select the Barracuda Spam Firewall instance you created and note the Public DNS address.
4. Open the browser and enter the copied Public DNS (from step 3) with port 8000 for HTTP. No port is required for HTTPS. For example:
For HTTP:
http://<Public DNS>:8000 (Unsecured)
For HTTPS:
https://<Public DNS> (Secured)
The Barracuda Spam Firewall virtual machine is not accessible via HTTPS port when it is booting up. Therefore, it is
recommended to use ONLY HTTP port to access the unit when booting. This displays the status of the unit i.e., System
Booting. Once the boot process is complete, the user will be redirected to the login page.
5. If you have the BYOL licensing option, skip to Verify Configuration and Change the Password below. If you have the BYOL licensing
option, the Licensing page appears. Enter your Barracuda Networks Token and Default Domain to complete licensing. Click Provision
. The Barracuda Spam Firewall connects to the Barracuda Update Server to get the required information based on your license, then
reboots automatically. Allow a few minutes for the reboot process.
53
Verify Configuration and Change the Password
1. Log into the Barracuda Spam Firewall appliance web interface as the administrator using the IP address and port as described in step 4
of Licensing of the Barracuda Spam Firewall after deploying on Amazon Web Services above. Log in with:
a. Username: admin
b. Password: Instance ID of your Barracuda Spam Firewall in Amazon Web Services.
2. Navigate to the BASIC > Administration page and enter your old password, new password, and re-enter the new password. Click Save
Password.
3. Navigate to the BASIC > IP Configuration page and do the following:
a. Verify that the IP Address, Subnet Mask, and Default Gateway are correct.
b. Enter the Server Name/IP of your destination email server where you want the Barracuda Spam & Firewall to deliver mail. For
example,
type: mail.<yourdomainname>.com
c. Verify that the Primary and Secondary DNS Server are correct.
d. Enter Default Hostname and, if you are using Hourly/Metered licensing option, Default Domain. The Host Name appears in
reports, alerts, notifications and messages sent by the Barracuda Spam Firewall. The Default Domain is the domain for the
system and is appended to the Host Name. For example,
<yourcompanydomain.com>.
This is the name that will be associated with bounced messages.
e. Under Allowed Email Recipient Domain(s), enter each domain for which the Barracuda Spam Firewall will receive email. Note:
The Barracuda Spam Firewall will reject all incoming email addressed to domains not specified here.
Continue with Step 5 - Configure the Web Interface.
54
Configuring an Elastic IP Address for an Instance
en
When an instance of your Barracuda Spam Firewall virtual appliance is created, a public IP address is associated with the instance. That public
IP address changes if the instance is stopped or terminated. However, you can assign a persistent public IP address to the instance using Elastic
IP addressing, resolving this issue. For more information, see the Amazon Web Services article Elastic IP Addresses.
Allocating an Elastic IP Address to the Barracuda Spam Firewall Instance
1. Log into the Amazon EC2 Management Console.
2. From the EC2 dashboard, select Elastic IPs under NETWORK & SECURITY.
3. Click Allocate New Address. Click Yes, Allocate to confirm and allocate a new IP address. A random Public IP gets generated and
displayed in the Allocate New Address table.
Associating the Elastic IP Address with the Barracuda Spam Firewall Instance
1. In the Allocate New Address table, right click on the new IP address and select Associate.
2. In the Associate Address window, do the following:
a. Select the Instance and the Private IP Address of the instance from the respective lists.
OR
b. Select a Network Interface and the Private IP Address from the respective lists.
c. Select the Allow Reassociation check box.
3. Click Yes, Associate.
55
Creating a Security Group on Amazon Web Services
en
Security groups control the access to an instance by enabling you to make rules specifying the protocols, ports and source IP ranges permitted to
reach the instance. Multiple security groups can be created with different rules, and assigned to each instance. For more information on security
groups, see the AWS article Amazon EC2 Security Groups.
1. From the EC2 dashboard, select Security Groups under NETWORK & SECURITY.
2. Click Create Security Group.
3. In the Create Security Group window, do the following:
a. Enter a name to identify the security group.
b. Specify the description for the security group.
c. Select a VPC ID from the list and click Yes, Create.
4. The created group appears in the security group table.
5. Select the security group from the table, and specify the inbound and outbound traffic to be allowed for the instance.
By default, the Barracuda Spam Firewall web interface listens on port 8000 for HTTP and port 443 for HTTPS. Make sure these ports
(8000 and 443) are added in the Inbound rule of the security group associated with the Barracuda Spam Firewall. Also, add the port(s)
through which you configure the Service(s) for this instance.
56
Creating a VPC, Internet Gateway and Subnet
en
Follow the steps below to create an Amazon Virtual Private Cloud (VPC), an Internet Gateway and a Subnet on Amazon Web Services (AWS).
Step 1 – Create the Amazon VPC Cloud
A Virtual Private Cloud (VPC) is an isolated virtual network on Amazon Web Services (AWS) Cloud where you can launch AWS resources, such
as Amazon EC2 instances. When creating a VPC, the IP address(es) should be in the form of Classless Inter-Domain Routing (CIDR) block (for
example, 10.0.0.0/16). In a VPC, you can select your own IP address range, create subnets, configure routing tables and network gateways.
The VPC cannot be larger than /16.
For more information about CIDR notation, refer to Classless Inter-Domain Routing on Wikipedia. For information about the number of VPCs that
you can create, refer to Amazon VPC Limits.
Perform the steps below to create a VPC:
1. Go to the AWS Management Console.
2. In the Compute & Networking section, click VPC.
3. From the VPC Dashboard, select Your VPCs under VIRTUAL PRIVATE CLOUDS.
4. Click Create VPC.
5. In the Create VPC dialog box, do the following:
a. Enter the IP address in the CIDR Block field.
b. Select Default from the Tenancy drop-down list.
6. Click Yes, Create.
Step 2 - Add an Internet Gateway to the VPC
57
By default, the instances launched on the Virtual Private Cloud (VPC) cannot communicate with the internet until an Internet Gateway is created
and attached to the VPC.
Perform the following steps to add an internet gateway to your VPC:
1. From the VPC Dashboard, select Internet Gateways under VIRTUAL PRIVATE CLOUDS.
2. Click Create Internet Gateway.
3. In the Create Internet Gateway dialog box, click Yes, Create.
4. Select the internet gateway created in the above step, and then click Attach to VPC.
5. Select the VPC that you created in Step 1, and then click Yes, Attach.
Step 3 - Add a Subnet to the VPC
Perform the following steps to add a subnet to your VPC:
1. From the VPC Dashboard, select Subnets under VIRTUAL PRIVATE CLOUDS.
2. Click Create Subnet.
3. In the Create Subnet dialog box, do the following:
a. Select the created VPC from the VPC drop-down list.
b. Select the availability zone that your VPC resides from the Availability Zone drop-down list.
c. Specify the IP address(es) in the CIDR Block field.
4. Click Yes, Create.
Continue with the licensing process on Amazon Web Services.
58
59
Routing Mail Through Amazon Web Services
enIn order to preserve the quality of the Amazon Web Services environment for sending email, Amazon Web Services enforces default limits on
the amount of email that can be sent from EC2 accounts. Before you put your Barracuda Spam Firewall into production, you need to request
Amazon Web Services to remove the default email sending limits.
To do so, visit https://portal.aws.amazon.com/gp/aws/html-forms-controller/contactus/ec2-email-limit-rdns-request, sign into your Amazon Web
Services account and fill in the three required fields on the form, as shown in Figure 1 below. While you await a response to the request, you can
send small amounts of test email through the Barracuda Spam Firewall.
Important
If you do not take this step, you may experience large queues of mail and/or deferred mail that will eventually be delivered, but may be
delayed.
Here is a recommended, generic Use Case Description that you might use in the form:
We are putting the Barracuda Spam Firewall into a production environment and, as such, require consistent mail delivery.
Figure 1. Amazon Web Services form to request removal of email sending limitations
60
Microsoft Azure
en
Microsoft Azure is a public cloud service, with instances that use one virtual network interface with a dynamic IP address per virtual appliance. Th
e Barracuda Spam Firewall can be deployed as a virtual appliance in the Microsoft Azure cloud to protect your email server from spam, virus,
spoofing, phishing and spyware attacks. Outbound filtering and encryption options also prevent confidential or sensitive information from being
purposely or inadvertently leaked outside the organization. The optional cloud protection layer (CPL) shields email servers from inbound malware
and DoS attacks while filtering out normal spam before it ever touches the network’s perimeter.
Licensing Options
The Barracuda Spam Firewall is available on Microsoft Azure with the Bring Your Own License (BYOL) and Hourly / Metered options.
Bring Your Own License (BYOL)
With the Bring Your Own License (BYOL) option, you are required to get the Barracuda Spam Firewall license token, either by:
Providing the required information for a free evaluation at https://www.barracuda.com/purchase/evaluation OR
Purchasing online at https://www.barracuda.com/purchase.
With this license option, there will be no Barracuda Spam Firewall Software charges, but Microsoft Azure usage charges on Microsoft
will be applicable.
You can either begin with the free evaluation OR purchase the Barracuda Spam Firewall license directly after deploying the VM or when
accessing the VM web interface for the first time.
BYOL Models and Instance Types
For BYOL, the Barracuda Spam Firewall virtual appliance is available in three sizes on Microsoft Azure. The following table lists each size level
with their corresponding instance type, cores, and memory allocated to each instance type. You'll select the Instance Type in the next step in Ho
w to Deploy the Barracuda Spam Firewall on Microsoft Azure. If you want to increase the performance of a license that you have already
purchased, you can buy additional cores from Barracuda and reconfigure for a larger instance type.
Supported Instance Type
in Microsoft Azure
Cores
Memory
Level 3 - (A1)
1
1.7 GB
Level 4 - (A2)
2
3.5 GB
Level 6 - (A3)
4
7 GB
You are limited to 1.7 GB of memory when deploying a Level 3 (A1) instance in Microsoft Azure. This limitation should not affect the
operation of the Barracuda Spam Firewall when deployed in this environment. Also note that, if you need to add additional storage:
For Barracuda virtual machines purchased through the Microsoft Azure Marketplace as of February 2015, you must create a
new attached drive. See How to add Additional Storage to your Azure Deployment.
For earlier deployments, you cannot attach new storage.
Hourly / Metered
With the Hourly/Metered licensing option, you complete the purchase or evaluation of the Barracuda Spam Firewall entirely within the Microsoft
Azure gallery. After the instance is launched, it is provisioned automatically. You are charged hourly for both the Barracuda Spam Software and
Microsoft Azure usage on Microsoft.
Hourly / Metered Model and Instance Types
For more information on supported instance types, Default vCPU, Default Memory and Hourly pricing, refer to Barracuda Spam Firewall Pricing
Details.
If you want to increase the performance of an existing VM, configure it with a larger instance type on Microsoft Azure and you will be charged
accordingly by Microsoft. The VM will automatically be reconfigured by Microsoft with the resources and capabilities of the larger instance type.
Before You Begin
Create an Azure Virtual Network
1. Log into your Microsoft Azure Management Portal.
2. In the left pane, click NETWORKS, and then click NEW at the bottom of the screen.
2.
61
3. Click NETWORK SERVICES > VIRTUAL NETWORK > CUSTOM CREATE. The CREATE A VIRTUAL NETWORK window appears.
4. On the Virtual Network Details page:
a. Enter a unique name in the Name field. For example, AzureVirtualNet
b. Select a location from the LOCATION drop-down list. The virtual network can only be used for Azure instances in this
geographic region. E.g., South Central US
c. Click Next
5. (Optional) On the DNS Servers and VPN Connectivity page, select or enter your DNS SERVERS.
6. Click Next
7. On the Virtual Network Address Spaces page, configure the ADDRESS SPACE:
a. STARTING IP: Enter the first IP address of the address space you want to use.
b. CIDR: Select the subnet mask for the virtual network. The maximum number of instances for a virtual network are listed in
parentheses.
8. Add a SUBNET:
a. STARTING IP: Enter the first IP address of the subnet.
b. CIDR: Select the subnet mask for the subnet.
62
9. Click Next
The created virtual network gets displayed in the VIRTUAL NETWORKS lists.
Next Step
Continue with How to Deploy the Barracuda Spam Firewall on Microsoft Azure for instructions on installation and configuration.
63
How to Deploy the Barracuda Spam Firewall on Microsoft Azure
en
This guide walks you through the steps to deploy and provision the Barracuda Spam Firewall on Microsoft Azure.
Microsoft Azure charges apply. For more information, see the Microsoft Azure Pricing Calculator. Important: If you need to add
additional storage after deployment:
For Barracuda virtual machines purchased through the Microsoft Azure Marketplace as of February 2015, you must create a
new attached drive.
For earlier deployments, you cannot attach new storage.
In this article
en
Before You Begin
Deploy and Provision the Barracuda Spam Firewall
Next Step
Before You Begin
If your organization does not have an Azure account, go to the Microsoft Azure purchase options page, and follow the onscreen instructions to
create an account.
Deploy and Provision the Barracuda Spam Firewall
1. Log into the Microsoft Azure Management Portal.
2. Click Marketplace at the bottom of the screen.
3. In the Marketplace window, select Virtual Machines and enter Barracuda Spam Firewall in the text field.
4. Mouse over the search result and select Barracuda Spam Firewall (BYOL or Hourly/Metered as per your requirement). Read the
product overview, and then click Create.
If you want to deploy a BYOL image, select the Barracuda Spam Firewall (BYOL) image.
64
5. On the Create VM page:
a. Enter the host name in the HOST NAME field.
b. Enter a username in the USER NAME field . This entry is not used by the Barracuda Spam Firewall.
c. Under Authentication Type, choose SSH Public Key or Password based on your selection. Note that this entry will not be used
by the Barracuda Spam Firewall.
d. Select the PRICING TIER based on your requirement.
e. In the OPTIONAL CONFIGURATION section, do the following:
i. AVAILABILITY SET - Configure as per your requirement.
ii. NETWORK - Configure the network in which you want to deploy the Barracuda Spam Firewall. Ensure it is in the same
network as your web servers.
iii. STORAGE ACCOUNT - Select an existing storage account or create a storage account
iv. ENDPOINTS - By default, port 8000 (TCP) and port 443 (TCP) will be opened as endpoints to access the web interface
of the Barracuda Spam Firewall. Port 25 (TCP) is also opened by default. Configure additional endpoints if needed on
the Barracuda Spam Firewall.
v. EXTENSIONS - Do not add any extension, as the Barracuda Spam Firewall does not support extensions.
f. Select a group in RESOURCE GROUP.
g. Choose the subscription for the instance and click Create.
h.
Read the legal terms in the Buy page and click Buy to complete the deployment.
65
After clicking Buy, Microsoft Azure begins provisioning the Barracuda Spam Firewall. You can check the status of the provisioned Barracuda
Spam from the Microsoft Azure Portal. Allow a few minutes before taking any further actions in the Portal. During this time, the Microsoft Azure
Linux Agent and Barracuda Spam Firewall image boots up.
Make sure you do not restart the Barracuda Spam Firewall while it is provisioning.
Next Step
Continue with the Barracuda Spam Firewall Quick Start Guide on Microsoft Azure.
66
Barracuda Spam Firewall Quick Start Guide on Microsoft Azure
en
Virtual machines (VMs) deployed through Azure Gallery prior to mid February, 2015 do not support Disk Expansion. If you
deployed prior to this time period and want to expand the disk, you must re-deploy the VM using the latest VM image available in
Azure Gallery. See How to add Additional Storage to your Azure Deployment .
Make sure you have completed the steps in the article How to Deploy the Barracuda Spam Firewall on Microsoft Azure before
continuing with the instructions below.
Licensing of Barracuda Spam Firewall after deploying on Microsoft Azure
If you deployed the Barracuda Spam Firewall with the Hourly/Metered option, you do not need to license the system; skip ahead to Ve
rify Configuration and Change the Password.
After provisioning the Barracuda Spam Firewall on Microsoft Azure, the next step is licensing. After you deploy the Barracuda Spam Firewall
image on the Microsoft Azure environment, do the following:
1. Sign in to the Microsoft Azure Portal.
2. Go to the VIRTUAL MACHINES and click on the Barracuda Spam Firewall instance you created, noting down the DNS.
3. Open the browser and enter the copied DNS (from step 2) with port 8000 for HTTP. No port is required for HTTPS. For example:
For HTTP
For HTTPS
: http://<DNS>:8000
: https://<DNS>
The Barracuda Spam Firewall virtual machine is not accessible via HTTPS port when it is booting up. Therefore, it is
recommended to use ONLY HTTP port to access the unit when booting. This displays the status of the unit i.e., System
Booting. Once the boot process is complete, the user will be redirected to the login page.
4. After the boot process is complete, the Licensing page displays with the following options:
If you already have a license token, click on that option and enter your Token and Default Domain, and then click Provision.
The Barracuda Spam Firewall connects to the Barracuda Update Server to get the required information based on your license,
then reboots automatically. Allow 5 or more minutes for the reboot process.
a. I Already Have a License Token – Use this option to provision your Barracuda Spam Firewall with the license token you have
already obtained from Barracuda Networks. Enter your Barracuda Networks Token and Default Domain to complete licensing,
and then click Provision.
The Barracuda Spam Firewall connects to the Barracuda Update Server to get the required information based on your license,
and then reboots automatically. Allow a few minutes for the reboot process. Once the instance is provisioned, you are redirected
to the login page.
b. I Would Like to Purchase a License – Use this option to purchase the license token for the Barracuda Spam Firewall. Provide
the required information in the form, accept the terms and conditions, and click Purchase. The Barracuda Spam Firewall
connects to the Barracuda Update Server to get the required information based on your license, and then reboots automatically.
b.
67
Allow a few minutes for the reboot process. Once the instance is provisioned, you are redirected to the login page.
c. I Would Like to Request a Free Evaluation – Use this option to get 30 days free evaluation of the Barracuda Spam Firewall.
Provide the required information in the form, accept the terms and conditions, and click Evaluate. The Barracuda Spam Firewall
connects to the Barracuda Update Server to get the required information based on your license, and then reboots automatically.
Allow a few minutes for the reboot process. Once the instance is provisioned, you are redirected to the login page.
Verify Configuration and Change Password
After provisioning of the Barracuda Spam Firewall is complete, you will see the login page:
1. Log into the Barracuda Spam Firewall appliance web interface as the administrator:
Username: admin Password: admin
2. To prevent unauthorized use, change the default administrator password to a more secure password. You can only change the
administrator password for the web interface. Go to the BASIC > Administration page and enter your old password, new password, and
re-enter the new password.
3. Enter the Server Name/IP of the destination email server where you want the Barracuda Spam Firewall to deliver mail.
4. Enter Default Host Name in the Domain Configuration section of the page. The Host Name will be used in reporting and displays in
alerts, notifications and messages sent by the Barracuda Spam Firewall. The Default Domain is the domain for the system and is
appended to the Host Name.
6. Under Allowed Email Recipient Domain(s), enter each domain for which you want the Barracuda Spam Firewall to receive email.
The Barracuda Spam Firewall rejects all incoming email that is addressed to domains that are not specified here.
Update the Firmware
Go to the ADVANCED > Firmware Update page. If there is a new Latest General Release available, perform the following steps to update the
system firmware:
1. Click Download Now next to the firmware version that you want to install. To view the download progress, click Refresh. When the
download is complete, the Refresh button is replaced by the Apply Now button.
2. Click Apply Now to install the firmware. The firmware installation takes several minutes to complete.
After the firmware is applied, the Barracuda Spam Firewall virtual machine automatically reboots. The login page is displayed when the
system comes back up.
3.
68
3. Log back into the web interface and read the Release Notes to learn about enhancements and new features. It is also good practice to
verify settings that you have already entered, because new features might have been included with the firmware update.
For more information, see Product Activation and Update Firmware.
Verify the Barracuda Spam Firewall Configuration
After you install your Barracuda Spam Firewall virtual machine and configure your firewall, you can test the configuration. Go to the ADVANCED
> Troubleshooting page and ping updates.barracudacentral.com.
Next Step
Continue with the Configure the Barracuda Spam Firewall From the Web Interface section of Step 5 - Configure the Web Interface.
69
How to add Additional Storage to your Azure Deployment
en
Virtual machines (VMs) deployed through Azure Gallery prior to mid February, 2015 do not support Disk Expansion. If you
deployed prior to this time period and want to expand the disk, you must re-deploy the VM using the latest VM image available in
Azure Gallery.
1. Log in to the Microsoft Azure Portal.
2. Click Browse, and then click Virtual Machines:
3. Click on the Instance where you want to increase storage:
4. At the top of the pane, click Settings:
5. Click Disks:
6. click Attach New:
70
7. Enter the disk size as per your requirement.
8. Set Host Caching to None:
9. Click OK:
10. Once the task is complete, go to Settings of the selected Instance, and then click Restart:
During the reboot process, the Barracuda VM provisions the additional storage. This can take some time depending on the
region where your virtual machine is located and the amount of provisioned storage.
71
72
VMware vCloud Air Deployment
en
*vCloud® Air™ is a public cloud platform built on the trusted foundation of vSphere, compatible with your on-premises data center, that includes
infrastructure, disaster recovery, and various applications as service offerings. You can migrate your existing onsite Barracuda Spam Firewall Vx
virtual machine(s) to the public cloud or start up a new Barracuda Spam Firewall Vx directly in the cloud. For more information about the
Barracuda Spam Firewall, see Barracuda Spam Firewall - Overview.
Follow instructions below to purchase or get an evaluation of the Barracuda Spam Firewall on vCloudAir. After purchasing or obtaining an
evaluation, continue with How to Deploy the Barracuda Spam Firewall in VMware vCloud Air.
BYOL Licensing
The Barracuda Spam Firewall Vx is available on vCloud Air through the Bring Your Own License (BYOL) option only.
To get started, you must first acquire a Barracuda Spam Firewall license token either by:
Free evaluation:
1. Go to https://www.barracuda.com/purchase/evaluation, and select Barracuda Spam Firewall from the Select a Product drop-down
menu.
2. Enter the number of email users (employees).
3. Enter your contact information and corporate details, and then click Submit Request.
4. You will be contacted and supplied the free evaluation license token.
5. Download and extract the Barracuda Spam Firewall vCloud Air package from the Barracuda Download Portal.
Online Purchase
1.
2.
3.
4.
5.
6.
Go to https://www.barracuda.com/purchase, and select Barracuda Spam Firewall from the Product drop-down menu.
Select the model and configuration options.
Enter your contact, billing, and shipping information.
Verify your order and read and accept the Terms & Conditions, and then click Submit Request.
You will be contacted and supplied the purchased Barracuda Spam Firewall Vx license token.
Download and extract the Barracuda Spam Firewall vCloud package from the Barracuda Download Portal.
Barracuda Spam Firewall Vx Models Supported
The Barracuda Spam Firewall Vx 100, 300, 400 and 600 are available to deploy on VMWare vCloud Air. To ensure proper sizing of your
Barracuda Spam Firewall instance, see Allocating Cores, RAM, and Hard Disk Space for Your Barracuda Spam Firewall Vx.
Continue with How to Deploy the Barracuda Spam Firewall in VMware vCloud Air.
73
How to Deploy the Barracuda Spam Firewall in VMware vCloud Air
en
This deployment guide applies to new installations of the Barracuda Spam Firewall in vCloud® Air™. For additional information on the vCloud Air
configuration process, refer to VMware vCloud Suite.
1. Begin by logging into your vCloud Air account.
2. Click on Virtual Private Cloud OnDemand.
3. Click on New Virtual Machine > Create My Virtual Machine from Scratch.
4. Click the Add vApp from OVF icon, and select the .ova build you want to upload and deploy.This will be the image for the Barracuda
Spam Firewall you downloaded from VMware on vCloud Air. When finished, click Next.
74
5. Review the details for your image file before uploading. When finished, click Next.
6. Give your vApp a name, keeping in mind that it might contain more than one Barracuda Spam Firewall if you are deploying multiple
virtual machines. Select the virtual datacenter where you want to deploy your virtual machine(s). When finished, click Next.
75
7. Configure networks to which you want each Barracuda Spam Firewall to connect. Make sure to check the box Switch to the advanced
networking workflow at the bottom of the page. This action will populate the IP Assignment drop-down on the right side of the page.
You will have the the following options for private IP address assignment:
a. Click Static – IP Pool if you want vCloud Air to select and assign a private IP address from a pool of IP addresses that you have
defined, which your mail server will use to access the Barracuda Spam Firewall.
b. Click Static – Manual if you want to select and assign a private IP address that your mail server can use to access the
Barracuda Spam Firewall. You can then NAT that IP address to an external IP address.
c. Click DHCP to have a private IP address automatically assigned to your Barracuda Spam Firewall.
You will create a NAT rule below to map this private IP address to an external IP address.
When finished, click Next.
76
8. Select sizing per the recommendations in Allocating Cores, RAM, and Hard Disk Space for Your Barracuda Spam Firewall Vx for the
hardware components for your virtual machine. Then fill in the appropriate values as shown below. When finished, click Next.
9. Review your vApp settings, and then click Finish.
77
10. Open up the virtual machine console to see the private IP address of your instance, You can fetch a public IP address by clicking on Gat
eways > Public IPs. The next step is to map the public (external) IP address to the private IP address of your instance by creating a
NAT rule.
11. Create a NAT rule to reach your Barracuda Spam Firewall from the Internet (e.g. map it to the public IP address). To do this, go to Admi
nistration > Cloud Resources > Virtual Data Centers > VDC1 > Edge Gateways and right-click on the gateway. Select Edge
78
Gateway Services and click the NAT tab.
Note that in the initial setup, you need to edit the Firewall tab to enable all ports (or at least the critical ones) and to enable DHCP on the
edge gateway.
12. Go to the vCloud Air console and enter both the license token you received when you purchased your Barracuda Spam Firewall, and
your default domain, to provision the Barracuda Spam Firewall.
To access your Barracuda Spam Firewall, enter the public IP address and port in a browser, like this: <IP address>:<port>. Example:
10.1.2.3:8000. Log in as admin / admin.
Continue with the Barracuda Spam Firewall Quick Start Guide on vCloud Air.
79
80
Barracuda Spam Firewall Quick Start Guide on vCloud Air
en
After provisioning the Barracuda Spam Firewall using the How to Deploy the Barracuda Spam Firewall in VMware vCloud Air guide, you're ready
to set up your Barracuda Spam Firewall. If you haven't already logged into your Barracuda Spam Firewall web interface, enter the public IP
address and port in a browser, like this: <IP address>:<port>. Example: 10.1.2.3:8000. You'll see this login page:
Log into the Barracuda Spam Firewall appliance web interface as the administrator:
Username: admin
Password: admin
Verify Configuration and Change Password
1. To prevent unauthorized use, change the default administrator password to a more secure password. You can only change the
administrator password for the web interface. Go to the BASIC > Administration page and enter your old password, new password, and
re-enter the new password.
2. Enter the Server Name/IP of the destination email server where you want the Barracuda Spam Firewall to deliver mail.
3. Enter Default Host Name in the Domain Configuration section of the page. The Host Name will be used in reporting and displays in
alerts, notifications and messages sent by the Barracuda Spam Firewall. The Default Domain is the domain for the system and is
appended to the Host Name.
5. Under Allowed Email Recipient Domain(s), enter each domain for which you want the Barracuda Spam Firewall to receive email.
The Barracuda Spam Firewall rejects all incoming email that is addressed to domains that are not specified here.
Verify the Barracuda Spam Firewall Configuration
After you install your Barracuda Spam Firewall, test the configuration by going to the ADVANCED > Troubleshooting page and pinging
updates.barracudacentral.com.
Continue with the Configure the Barracuda Spam Firewall From the Web Interface section of Step 5 - Configure the Web Interface.
81
Getting Started
en
Recommended Steps
Barracuda Networks recommends first reviewing Deployment Options and choosing the best deployment for your network before following thes
steps to install and configure the Barracuda Spam Firewall:
Step 1 - Understand the Concepts
Step 2 - Install the Barracuda Spam Firewall
Step 3 - Initial Configuration
Step 4 - Product Activation and Firmware Update
Step 5 - Configure the Web Interface
Step 6 - Routing Inbound Mail
How to Tune and Monitor the Default Spam and Virus Settings
Quarantine: An Overview
Mail Journaling
How to Migrate From Postini to the Barracuda Spam Firewall
The articles linked above cover the entire installation and deployment process. However, if you are installing the Barracuda Spam & Firewall in a
server room or other location without access to a web browser, you can also download the Quick Start Guide (shipped with each appliance) as a
PDF:
Barracuda Spam Firewall Quick Start Guide (English)
Barracuda Spam Firewall Quick Start Guide (Japanese)
82
Step 1 - Understand the Concepts
en
The Barracuda Spam Firewall takes a configured action when it identifies a message as spam or otherwise in violation of configured Block and
Accept policies. Inbound messages may be Blocked, Quarantined, Tagged or Allowed, while outbound messages may be Blocked, Quarantined,
Encrypted or Sent. Note that using the Quarantine or Tag actions with some scanning layers described below may use more system resources
than Block or Allow actions.
In this article:
en
Twelve Layers of Defense
Maximizing Efficiency and Performance of Spam Scanning
Connection Management Layers
Denial of Service Protection
Rate Control
IP Analysis
Sender Authentication
Recipient Verification
Mail Scanning Layers
Virus Scanning
User-specified rules (custom policy)
Fingerprint Analysis
Intent Analysis
Image Analysis
Bayesian Analysis
Spam Scoring
Predictive Sender Profiling
Journaling
Twelve Layers of Defense
Understanding each of the 12 layers of defense available, as described below, prepares you to make decisions about which - if not all - of the
connection and mail scanning features to enable and tune for the best combination of performance and accuracy of the Barracuda Spam Firewall.
Maximizing Efficiency and Performance of Spam Scanning
Using Rate Control, Barracuda Reputation (realtime RBLs) and Recipient Verification, as described below, can maximize filtering performance of
the Barracuda Spam Firewall for inbound mail. These layers have the greatest impact on filtering speed and performance relative to all the other
layers such that any inappropriate incoming mail connections are dropped even before receiving the message.
Connection Management Layers
These layers provide the most value in your Barracuda Spam Firewall deployment for inbound mail as they identify and block unwanted email
messages before accepting the message body for further processing. The Connection Management layers generally require less processing time
than the seven content scanning layers that follow. For the average small or medium business, more than half of the total email volume can
be blocked using Connection Management techniques. Extremely large Internet Service Providers (ISPs) or even small Web hosts, while
under attack, may observe block rates at the Connection Management layers exceeding 99 percent of total email volume.
Denial of Service Protection
Built on a hardened and secure Linux operating system, the Barracuda Spam Firewall receives inbound email on behalf of the organization,
insulating your organization’s mail server from receiving direct Internet connections and associated threats. This layer does not apply to outbound
mail.
Rate Control
Automated spam software can be used to send large amounts of email to a single mail server. To protect the email infrastructure from these
flood-based attacks, the Barracuda Spam Firewall counts the number of incoming connections from a particular IP address (inbound mail) or
sender email address (outbound mail) during a 30 minute interval and throttles the connections once a particular threshold is exceeded. See Rate
Control Inbound for more on configuring this feature.
IP Analysis
After applying rate controls based on IP address, the Barracuda Spam Firewall performs analysis on the IP address of inbound mail based on the
following:
Barracuda Reputation - This feature leverages data on network addresses and domain names collected from spam traps and
83
throughout other systems on the Internet. The sending histories associated with the IP addresses of all sending mail servers are
analyzed to determine the likelihood of legitimate messages arriving from those addresses. IP addresses of incoming connections are
compared to the Barracuda Reputation Blocklist and the Barracuda Reputation Whitelist, if enabled, and suspicious incoming messages
are either blocked, tagged or quarantined.
External blocklists - Also known as real-time blocklists (RBLs) or DNS blocklists (DNSBLs). Several organizations maintain external
blocklists of known spammers.
Allowed and blocked IP address lists - Customer-defined policy for allowed and blocked IP addresses. By listing trusted mail servers
by IP address, administrators can avoid spam scanning of good email, both reducing processing requirements and eliminating the
chances of false positives. Likewise, administrators can define a list of bad email senders for blocking. In some cases, administrators
may choose to utilize the IP blocklists to restrict specific mail servers as a matter of policy rather than as a matter of spam protection.
Declaring an invalid “from” address is a common practice by spammers. The Barracuda Spam Firewall Sender Authentication layer uses a
number of techniques on inbound mail to both validate the sender of an email message and apply policy, including domain name spoof
protection, performing a DNS lookup of domain names and enforcing RFC 821 compliance.
Sender Policy Framework (SPF) tracks sender authentication by having domains publish reverse MX records to display which machines are
designated as mail sending machines for that domain. The recipient can check those records to make sure mail is coming from a designated
sending machine.
DomainKeys (DKIM) dictates that a sending domain cryptographically signs outgoing messages, allowing the sending domain to assert
responsibility for a message. When receiving a message from a domain, the recipient can check the signature of the message to verify that the
message is, indeed, from the sending domain and that the message has not been tampered with.
See Advanced Configuration for details on configuring this layer.
The Barracuda Spam Firewall verifies the validity of recipient email addresses for inbound messages (not outbound) through multiple techniques
to prevent invalid bounce messages. See Advanced Configuration to learn about LDAP integration, SMTP recipient verification and using a local
database for recipient verification.
Mail Scanning Layers
Virus Scanning
The most basic level of Mail Scanning is virus scanning. The Barracuda Spam Firewall utilizes three layers of virus scanning and automatically
decompresses archives for comprehensive protection. By utilizing virus definitions, Barracuda Spam Firewall customers receive the best and
most comprehensive virus and malware protection available. The three layers of virus scanning of inbound and outbound mail include:
Powerful open source virus definitions from the open source community help monitor and block the latest virus threats.
Proprietary virus definitions, gathered and maintained by Barracuda Central, our advanced 24/7 security operations center that works to
continuously monitor and block the latest Internet threats.
Barracuda Real-Time Protection (BRTS), a set of advanced technologies that enables each Barracuda Spam Firewall to immediately
block the latest virus, spyware, and other malware attacks as they emerge. This feature provides fingerprint analysis, virus protection and
intent analysis. When BRTS is enabled, any new virus or spam outbreak can be stopped in real-time for industry-leading response times
to email-borne threats. BRTS allows customers the ability to report virus and spam propagation activity at an early stage to Barracuda
Central.
Virus Scanning takes precedence over all other Mail Scanning techniques and is applied even when mail passes through the Connection
Management layers. As such, even email coming from “whitelisted” IP addresses, sender domains, sender email addresses or recipients are still
scanned for viruses and blocked if a virus is detected.
The Barracuda Exchange Antivirus Agent for the Microsoft Exchange Server is an add-in that empowers your mail server to do virus
scanning of internal mail and of previously stored mail using constantly updated virus signatures detected by Barracuda Central. See How to Get
and Configure the Barracuda Exchange Antivirus Agent 6.0.x for details about getting and installing the add-in from the Barracuda Spam Firewall
Web interface.
User-specified rules (custom policy)
Administrators can choose to define their own policies, perhaps for compliance or governance reasons, which take precedence over spam
blocking rules delivered to the system automatically through Barracuda Energize Updates. Administrators can set custom content filters for
inbound and/or outbound mail based on the subject, message headers, message bodies and attachment file type.
A message “fingerprint” is based on commonly used message components (e.g., an image) across many instances of spam. Fingerprint analysis
is often a useful mechanism for blocking future instances of spam once an early outbreak is identified. Engineers at Barracuda Central work
around the clock to identify new spam fingerprints which are then updated on all Barracuda Spam Firewalls through hourly Barracuda Energize
84
Updates. Both inbound and outbound email messages are subject to Fingerprint Analysis
Intent Analysis
All spam messages have an “intent” – to get a user to reply to an email, to visit a Web site or to call a phone number. Intent analysis involves
researching email addresses, Web links and phone numbers embedded in email messages to determine whether they are associated with
legitimate entities. Frequently, Intent Analysis is the defense layer that catches phishing attacks. The Barracuda Spam Firewall applies various
forms of Intent Analysis to both inbound and outbound mail, including real-time and multi-level intent analysis.
Image Analysis
While Fingerprint Analysis captures a significant percentage of images after they have been seen, the Barracuda Spam Firewall also uses Image
Analysis techniques on both inbound and outbound mail which protect against new image variants. These techniques include:
Optical character recognition (OCR) - Enables the Barracuda Spam Firewall to analyze the text rendered inside embedded images.
Image processing - To mitigate attempts by spammers to foil OCR through speckling, shading or color manipulation, the Barracuda
Spam Firewall also utilizes a number of lightweight image processing technologies to normalize the images prior to the OCR phase.
More heavyweight image processing algorithms are utilized at Barracuda Central to quickly generate fingerprints that can be used by the
Barracuda Spam Firewall to block messages.
Animated GIF analysis - The Barracuda Spam Firewall contains specialized algorithms for analyzing animated GIFs for suspect
content.
Bayesian Analysis
Bayesian Analysis applies only to inbound mail and is a linguistic algorithm that profiles language used in both spam messages and legitimate
email for any particular user or organization. To determine the likelihood that a new email message is spam, Bayesian Analysis compares the
words and phrases used in the new email against the corpus of previously identified email. The Barracuda Spam Firewall only uses Bayesian
Analysis after administrators or users profile a corpus of at least 200 legitimate (not spam) messages and 200 spam messages. Bayesian
Analysis does not apply to outbound mail.
Spam Scoring
Once an inbound or outbound message has passed the initial Barracuda Spam Firewall block/accept filters, it receives a score for its spam
probability. This score ranges from 0 (definitely not spam) to 9 or greater (definitely spam). Based on this score, the Barracuda Spam Firewall can
take one of the following actions:
Block
Quarantine
Tag (inbound mail only)
Allow (inbound mail only)
Send (outbound mail only)
Domain Level Spam Scoring: The Barracuda Spam Firewall 400 and higher allows for setting spam score levels for inbound mail at the domain
level. The administrator or the Domain admin role can set the spam scoring levels on the BASIC > Spam Checking page.
Per-User Spam Scoring: The Barracuda Spam Firewall 600 and higher allows the administrator to enable users to set their own spam score
levels for inbound mail if per-user quarantine is enabled. If per-user spam scoring is enabled, when the user logs into their account, they will see
the PREFERENCES > Spam Settings page from which they can set tag, quarantine and block scoring levels for that account.
Predictive Sender Profiling
When spammers try to hide their identities, the Barracuda Spam Firewall can use Predictive Sender Profiling to identify behaviors of all senders
and apply the applicable Barracuda Spam Firewall defense tactic to reject connections and/or messages from spammers. This involves looking
beyond the reputation of the apparent sender of a message, just like a bank needs to look beyond the reputation of a valid credit card holder of a
card that is lost or stolen and used for fraud.
Some examples of spammer behavior that attempts to hide behind a valid domain, and the Barracuda Spam Firewall features that address them,
include the following:
Sending too many emails from a single network address
Automated spam software can be used to send large amounts of email from a single mail server. The Rate Control feature on the
Barracuda Spam Firewall can be set to limit the number of connections made from any IP address within a 30 minute time period.
Violations are logged to identify spammers. Rate Control is configured from the BLOCK/ACCEPT > Rate Control page.
The Messages Per SMTP Session setting limits the number of messages allowed in one SMTP session. If the number of messages in
one session exceeds this threshold, the rest of the messages are temporarily blocked and are displayed in the message log as being
"Deferred" with "Per-Connection Message Limit Exceeded" as the reason for the postponement. The sender is required to make a new
connection to continue sending messages, which may ultimately trigger a Rate Control deferral. For this and other SMTP security
settings, see the ADVANCED > Email Protocol page.
85
Attempting to send to too many invalid recipients
Many spammers attack email infrastructures by harvesting email addresses. Recipient Verification on the Barracuda Spam Firewall
enables the system to automatically reject SMTP connection attempts from email senders that attempt to send to too many invalid
recipients, a behavior indicative of directory harvest or dictionary attacks.
Using LDAP lookup or a local database to verify valid recipients as well as Sender Spoof Protection, which blocks email with "From"
addresses which use an allowed recipient domain on the Barracuda Spam Firewall, protects against receiving mail targeted to invalid
recipients.
Registering new domains for spam campaigns
Because registering new domain names is fast and inexpensive, many spammers switch domain names used in a campaign and send
blast emails on the first day of domain registration. Real-time Intent Analysis on the Barracuda Spam Firewall is typically used for new
domain names and involves performing DNS lookups and comparing DNS configuration of new domains against the DNS configurations
of known spammer domains.
Using free Internet services to redirect to known spam domains
Use of free Web sites to redirect to known spammer Web sites is a growing practice used by spammers to hide or obfuscate their identity
from mail scanning techniques such as Intent Analysis. With Multilevel Intent Analysis, the Barracuda Spam Firewall inspects the
results of Web queries to URIs of well-known free Web sites for redirections to known spammer sites.
Journaling
The Barracuda Spam Firewall provides an avenue for recording a copy of, or journaling, email communications in your organization and sending
them to a dedicated email address that you specify. The process of journaling is different from archiving; journaling is simply a means of
recording your users’ messages. Archiving, on the other hand, is a means of storing those copies in a separate environment for the purpose of
regulatory compliance, data retention, or server maintenance. For archiving, consider also deploying the Barracuda Message Archiver.
Continue with Deployment Options.
86
Step 2 - Install the Barracuda Spam Firewall
en
Virtual Machine Installation
If you are using the Barracuda Spam Firewall Vx, see the Virtual Deployment page to get and install your Barracuda Spam Firewall Vx virtual
machine.
Checklist for Unpacking
Before installing your Barracuda Spam Firewall, match the items on this list with the items in the box. If any item is missing or damaged, please
contact your Barracuda Networks Sales representative.
Barracuda Spam Firewall (check that you have received the correct model)
AC power cord
Mounting rails (Barracuda Spam Firewall 600, 800, and 900 only)
Also required for installation:
VGA monitor
PS2 keyboard
Ethernet cables
To physically install the Barracuda Spam Firewall:
1. Fasten the Barracuda Spam Firewall to a standard 19-inch rack or other stable location.
Important: Do not block the cooling vents located on the front and rear of the unit.
2. Connect a CAT5 Ethernet cable from your network switch to the Ethernet port on the back of your Barracuda Spam Firewall.
The Barracuda Spam Firewall supports both 10BaseT and 100BaseT Ethernet. Barracuda Networks recommends using a 100BaseT
connection for best performance.
The Barracuda Spam Firewall 600 and higher supports Gigabit Ethernet and has two usable LAN ports. On these models, plug
the Ethernet cable into the LAN 2 port.
Do not connect any other cables to the other connectors on the unit. These connectors are for diagnostic purposes.
3. Connect the following to your Barracuda Spam Firewall:
Power cord
VGA monitor
PS2 keyboard
After you connect the AC power cord the Barracuda Spam Firewall may power on for a few seconds and then power off. This is standard
behavior.
4. Press the Power button located on the front of the unit. The login prompt for the administrative console is displayed on the monitor, and
the light on the front of the system turns on. For a description of each indicator light, refer to Barracuda Spam Firewall Panel Indicators,
Ports, and Connectors.
APC UPS Support
An APC (American Power Conversion) UPS (Uninterruptible Power Supply) device with a USB interface is supported with the Barracuda Spam
Firewall. No configuration changes are needed on the Barracuda Spam Firewall to use one. When the APC UPS device is on battery power, the
web interface will display an alert, and the Barracuda Spam Firewall will shut down safely when there is an estimated time of 3 minutes of battery
power remaining.
Continue with Step 3 - Initial Configuration.
87
en
Configure IP Address and Network Settings
The Barracuda Spam Firewall is given a default IP address of 192.168.200.200. You can change this address by doing either of the following:
Connect directly to the Barracuda Spam Firewall with a keyboard and monitor and specify a new IP address through the console
interface.
Applies only to the Barracuda Spam Firewall 200, 300, 400, and 600: Push and hold the Reset button on the front panel. Holding the Res
et button for 5 seconds changes the IP address to the default of 192.168.200.200. Holding the Reset button for 8 seconds changes the
IP address to 192.168.1.200. Holding the Reset button for 12 seconds changes the IP address to 10.1.1.200.
To connect directly to the Barracuda Spam Firewall to set a new IP address:
1. At the barracuda login prompt, enter admin for the login and admin for the password. The User Confirmation Requested window will
display the current IP configuration of the system.
2. Using the Tab key, select Yes to change the IP configuration.
3. Enter the new IP address, netmask, and default gateway for your Barracuda Spam Firewall, and select OK when finished.
4. Select No when prompted if you want to change the IP configuration. Upon exiting the screen, the new IP address and network settings
will be applied to the Barracuda Spam Firewall.
Configure Your Corporate Firewall
If your Barracuda Spam Firewall is located behind a corporate firewall, you need to open specific ports to allow communication between the
Barracuda Spam Firewall and remote servers.
To configure your corporate firewall:
1. Using the following table as a reference. Open the specified ports on your corporate firewall:
Port
Direction
Protocol
Used for
22
Out
TCP
Remote diagnostics and
technical support services
(recommended)
25
In/Out
TCP
SMTP
53
Out
TCP/UDP
Domain Name Server (DNS)
80
Out
TCP
Virus, firmware, security and
spam rule definitions
123
Out
UDP
NTP (Network Time Protocol)
2. If appropriate, change the NAT routing of your corporate firewall to route incoming email to the Barracuda Spam Firewall. Consult your
firewall documentation or your corporate firewall administrator to make the necessary changes.
88
After specifying the IP address of the system and opening the necessary ports on your firewall, you need to configure the Barracuda Spam
Firewall from the web interface. Make sure the computer from which you configure the Barracuda Spam Firewall is connected to the same
network, and the appropriate routing is in place to allow connection to the Barracuda Spam Firewall’s IP address from a web browser.
Configure the Barracuda Spam Firewall From the Web Interface
1. From a web browser, enter the IP address of the Barracuda Spam Firewall followed by port 8000.
Example: http://192.168.200.200:8000
2. Log in to the web interface by entering admin for the username and admin for the password.
3. On the BASIC > IP Configuration page, enter the required information in the fields as described in the following table:
Fields
Description
TCP/IP Configuration
The IP address, subnet mask, and default gateway of your
Barracuda Spam Firewall. The TCP port is the port on which the
Barracuda Spam Firewall receives incoming email. This is
usually port 25.
Destination Mail Server TCP/IP Configuration
The hostname or IP address of your destination mail server; for
example mail.yourdomain.com. This is the mail server that
receives email after it has been checked for spam and viruses.
You should specify your mail server’s hostname rather than its IP
address so that the destination mail server can be moved and
DNS updated at any time without any changes needed to the
TCP port is the port on which the destination mail server receives
all SMTP traffic such as inbound email. This is usually port 25.
If you need to set up more than one domain or mail server, refer
to Creating and Managing Domains.
DNS Configuration
The primary and secondary DNS servers you use on your
network.
It is strongly recommended that you specify a primary and
secondary DNS server. Certain features of the Barracuda Spam
Firewall rely on DNS availability.
Domain Configuration
Default Host Name is the host name to be used in the reply
address for email messages (non-delivery receipts, virus alert
notifications, etc.) sent from the Barracuda Spam Firewall. The
Default Host Name is appended to the default domain.
Default Domain is a required field and indicates the domain
name to be used in the reply address for email messages
(non-delivery receipts, virus alert notifications, etc.) sent from the
Accepted Email Recipients Domains
The domains managed by the Barracuda Spam Firewall. Make
sure this list is complete. The Barracuda Spam Firewall rejects all
incoming messages addressed to domains not in this list. See Cr
eating and Managing Domains.
Note: One Barracuda Spam Firewall can support multiple
domains and mail servers. If you have multiple mail servers, go
to the DOMAINS tab and enter the mail server associated with
each domain
4. Click Save.
If you changed the IP address of your Barracuda Spam Firewall, you are disconnected from the web interface and will need to log in
again using the new IP address.
If You Have a Model 100
Go to the Users page and perform at least one of the following:
Enter the email address(es) on which the Barracuda Spam Firewall is to perform spam and virus scanning under User
89
Configuration, one entry per line.
To have email addresses automatically added to the Barracuda Spam Firewall as mail arrives, make sure the Enable User
Addition option is turned on.
Note: If no users are specified, AND the Enable User Addition option is set to No, then no scanning of ANY incoming email
will be performed.
Continue with Step 4 - Product Activation and Firmware Update
90
Step 4 - Product Activation and Firmware Update
en
Online Activation and Update
The Barracuda Spam Firewall can automatically update its activation status. Complete the following steps to initiate the online activation process
and update the system.
1. Log into the Barracuda Spam Firewall as the administrator. In a web browser, enter the Barracuda Spam Firewall management IP
address and default HTTP port (for example, http://192.168.200.200:8000/). Use the default admin credentials:
Username: admin
Password: admin
2. Go to the BASIC > Dashboard page. Under Subscription Status, make sure the Energize Updates subscription displays Current. If
the Barracuda Spam Firewall can access the activation servers, your Energize Update and Instant Replacement subscriptions are most
likely active. If not, a warning displays at the top of every page and you must activate your subscriptions before continuing.
3. If the Energize Updates displays Not Activated:
a. Click the activation link at the top of the page to go to the Barracuda Networks Product Activation page and complete activation
of your subscriptions.
b. Go back to the Subscription Status section of the BASIC > Dashboard page, and click Refresh to automatically update the
activation status of the Energize Updates subscription.
Update the Firmware
Go to the ADVANCED > Firmware Update page. If there is a new Latest General Release available, do the following to update the system
firmware:
1. Click the Download Now button located next to the firmware version that you wish to install.
2. Click the Apply Now button to install the firmware. This will take a few minutes to complete. To avoid damaging the Barracuda Spam
Firewall, do not manually power OFF the system during an update or download.
3. After the firmware has been applied, the Barracuda Spam Firewall will automatically reboot and display the login page.
4. Log back into the web interface and read the Release Notes to learn about enhancements and new features. Verify settings you may
have already entered, as new features may have been included with the firmware update.
91
Step 5 - Configure the Web Interface
en
Controlling Access to the Web Interface
The BASIC > Administration page allows you to perform the following tasks for initial setup:
Required: Provide email addresses in the Email Notifications section of the page so the Barracuda Spam Firewall and Barracuda
Networks can send out important alerts and informative notifications if needed.
Change the HTTP port used to access the web interface. For security, HTTPS access is recommended - see Securing the Barracuda
Spam Firewall. To enable SSL-access only, see How to Enable SSL for Administrators and Users.
Change the length of time users can be logged into the web interface after a period of no activity ( Session Expiration Length - default
is 20 minutes).
Specify the IP addresses and netmask of the systems that can access the web interface. All other systems will be denied access. This is
configurable in the section.
Customizing the Appearance of the Web interface
The ADVANCED > Appearance page allows you to customize the default images used on the web interface. This tab is only displayed on the
Barracuda Spam Firewall 600 and higher.
Changing the Language of the Web Interface
You can change the language of the web interface by selecting a language from the drop-down menu in the upper right corner of the page near
the Log Off link. Supported languages include Chinese, Japanese, Spanish, French, and others. The language you select is only applied to your
individual web interface. No other user’s web interface is affected.
Setting the Time Zone of the System
You can set the time zone of your Barracuda Spam Firewall from the BASIC > Administration page. The current time on the system is
automatically updated via Network Time Protocol (NTP). When the Barracuda Spam Firewall resides behind a firewall, NTP requires port 123 to
be opened for outbound UDP traffic. You can specify one or more NTP servers to use on the ADVANCED > Advanced Networking page. Each
server will be tried in order until one successfully connects. The default server is ntp.barracudacentral.com.
It is important that the time zone is set correctly because this information is used in all logs and reports.
Note: The Barracuda Spam Firewall automatically reboots when you change the time zone.
Continue with Step 6: Routing Inbound Mail.
92
How to Enable SSL for Administrators and Users
en
SSL (Secure Socket Layer) ensures that your passwords are encrypted and that all data transmitted to and received from the web interface is
encrypted as well. All Barracuda Spam Firewalls support SSL access without any additional configuration. However, some sites may wish to
enforce using a secured connection to access the web interface, or prefer to use their own trusted certificates. For more information about and
best practices for securing your Barracuda Spam Firewall on your network, see Securing the Barracuda Spam Firewall.
The SSL configuration referred to here is related only to the web interface. There is no need to explicitly configure SSL for traffic between the
Barracuda Spam Firewall and your mail servers.
How to Enforce SSL-only Access (recommended)
1. On the ADVANCED > Secure Administration page, select Yes to enable HTTPS/SSL access only to the web interface. Setting this to
No will still allow the Barracuda Spam Firewall to accept non-SSL connections.
2. Select Yes to Use HTTPS links in emails for per-user quarantine messages sent from the Barracuda Spam Firewall.
3. Enter your desired web Interface HTTPS/SSL port for the web interface. The default is 443.
4. Click Save.
If you wish to change the certificate that is used, you must first create and upload it to the Barracuda Spam Firewall before changing the Certifica
te Type in the SSL Certificate Configuration section of the ADVANCED > Secure Administration page. See the online help for instructions.
The Barracuda Spam Firewall supports the following types of certificates:
Default (Barracuda Networks) certificates are signed by Barracuda Networks. On some browsers, these may generate some benign
warnings which can be safely ignored. No additional configuration is required to use these certificates, and are provided free of charge as
the default type of certificate.
Private (self-signed) certificates provide strong encryption without the cost of purchasing a certificate from a trusted Certificate Authority
(CA). These certificates are created by providing the information requested in the Private (self-signed) section of the page. You may also
want to download the Private Root Certificate and import it into your browser, to allow it to verify the authenticity of the certificate and
prevent any warnings that may come up when accessing the web interface.
93
Step 6 - Routing Inbound Mail
en
The next step in setting up your Barracuda Spam Firewall is to route incoming email to the system so it can scan incoming messages for spam
and viruses. Note that inbound mail will be blocked if the domain receiving the mail has not been configured on the Spam Firewall. To
configure domains, see Creating and Managing Domains.
Important: In addition to this article, iIf you are using:
Google Apps Business and Education editions with the Barracuda Spam Firewall as your inbound mail gateway, please
see How to Configure Google Apps for Inbound and Outbound Mail in addition to reading this article.
Amazon Web Services, see Routing Mail Through Amazon Web Services
You can use either of the following methods to route messages to your Barracuda Spam Firewall:
Use port forwarding to redirect incoming SMTP traffic (port 25) to the Barracuda Spam Firewall if it is installed behind a corporate
firewall running NAT (Network Address Translation). Configure this option on the ADVANCED > Advanced Networking page. For more
information about port forwarding, refer to your firewall documentation or network administrator.
MX records are used when your Barracuda Spam Firewall is located in a DMZ with a routeable public IP address. If your Barracuda
Spam Firewall is in the DMZ (not protected by your corporate firewall), do the following to route incoming messages to the system:
1. Create a DNS entry for your Barracuda Spam Firewall. The following example shows a DNS entry for a Barracuda Spam Firewall with a
name of barracuda and an IP address of 66.233.233.88:
barracuda.yourdomain.com
IN
A
66.233.233.88
2. Change your DNS MX Records. The following example shows the associated MX record with a priority number of 10:
IN MX 10 barracuda.yourdomain.com
You can configure specific SMTP settings from the ADVANCED > Email Protocol page. After you route incoming email to the
Barracuda Spam Firewall, it will begin filtering all email it receives and routing good email to your mail server.
Testing Spam and Virus Scanning With a Local User Set
From the ADVANCED > Explicit Users page, you have the option to use the Explicit Users to Scan For feature to test a subset of locally
defined users before fully deploying the Barracuda Spam Firewall.
To tune your spam settings, continue with How to Tune and Monitor the Default Spam and Virus Settings.
If you will be routing outbound mail through the Barracuda Spam Firewall, continue with Routing Outbound Mail.
94
Using MX Records
en
This article defines MX records and provides information about effectively using MX records in conjunction with Spam firewalls.
MX Records
MX records are DNS entries that are used by sending mail servers to locate destination mail servers. An mail server sending an email to a
particular domain will look up the MX record for that destination domain. The MX record provides a machine name or an IP address for the
destination domain. For example, if an mail server wants to send an email to [email protected], it would perform an MX record look up on
mydomain.com to determine the destination IP address. Once the sending mail server has the destination IP address, it would then be able to
contact the destination machine to deliver the email.
Figure 1: Basic MX record setup.
Multiple MX Records
Some domains have several MX records associated with it. Each MX record has a different priority associated with it and each one points to a
different server as illustrated in Figure 2:
Figure 2: Domain with multiple MX records.
When a sending mail server performs an MX record lookup on a destination domain, it obtains the complete list of MX records and their
associated priorities. Under normal circumstances, the sending mail server will attempt to send the email to the highest priority destination first
95
and only proceed down the list if the higher priority machine is down, overloaded or cannot take the email for some reason. This is particularly
useful when building robust and high availability systems. The email is delivered according to the highest priority MX record. If the mail server
specified in that record is down, then the email is routed according to the next highest priority MX record.
Using a Spam Firewall
To help block spam and viruses, some organizations may have their mail server’s highest priority MX record point to a Spam firewall rather than
the mail server itself. This way the first machine to receive the email would be the Spam firewall. The Spam firewall would then process the email
and determine if the email is legitimate. If it is, then it would forward the email to the destination mail server.
Figure 3: MX Record and the Barracuda Spam Firewall.
To protect against the case of the Spam firewall going down, some organizations have a lower priority or backup MX record that points directly to
the mail server.
Figure 4: Wrong method for obtaining high availability.
This, however, is not a recommended way to protect against a Spam firewall failing. Why? Spammers know about this method and will take
advantage of the lower priority MX record that bypasses the Spam firewall. Spammers will send Spames directly to the lower priority MX record
so that they will always bypass the Spam firewall and get through to the mail server.
For organizations who wish to protect against a Spam firewall failing, Barracuda Networks recommends having both the first and second priority
MX records point to a Spam firewall and the Spam firewall pointing to an mail server. This way all email, regardless of which MX record is being
used, is always processed by a Spam firewall first.
Figure 5: Correct method for obtaining high availability.
96
Summary
To effectively use MX records with Spam firewalls, Barracuda Networks recommends having the highest priority MX record point to the Spam
firewall and the Spam firewall point to the mail server.
To have a high availability environment, Barracuda Networks recommends having a lower priority MX record point to another Spam firewall and
the Spam firewall point to an mail server. It is not effective to have the lower priority MX record point directly to an mail server since spam and
viruses will simply bypass the higher priority MX record and use the lower priority MX record to send spam and viruses directly to the mail server.
To use MX records with the Barracuda Spam Firewall when configuring the destination mail server, set the Use MX Records option on the BASI
C > IP Configuration page in the web interface. This setting is available globally (applied for all domains) and also can be specified at the
domain level.
97
How to Tune and Monitor the Default Spam and Virus Settings
en
After you install the Barracuda Spam Firewall, the system begins filtering incoming email based on the default settings. The system automatically
checks incoming email for viruses and uses the Barracuda Reputation service to identify spam.
In This Section:
How to Get and Configure Barracuda Exchange Antivirus Agent 7.1 and Above
How to Get and Configure the Barracuda Exchange Antivirus Agent 6.0.x
Virus Checking and Notifications
How Spam Scoring Works
Monitoring Inbound and Outbound Email Traffic
Performance and Email Statistics
98
How to Get and Configure Barracuda Exchange Antivirus Agent 7.1 and Above
en
This article refers to Barracuda Spam Firewall version 7.1 and above and the 7.1 version of the Barracuda Exchange Antivirus
Agent. This version of the agent only supports Microsoft Exchange Server version 2013. If you have versions 2007 or 2010 of
Microsoft Exchange Server:
You need to download and install the Barracuda Exchange Antivirus Agent 6.0.x from the ADVANCED > Exchange
Antivirus page in the Barracuda Spam Firewall web interface.
See How to Get and Configure the Barracuda Exchange Antivirus Agent 6.0.x. to configure.
The Barracuda Exchange Antivirus Agent no longer supports Microsoft Exchange Server version 2003.
What is the Barracuda Exchange Antivirus Agent?
The Barracuda Exchange Antivirus Agent is a Microsoft Exchange Server transport agent that works with the Barracuda Spam Firewall to scan
internally generated mail for viruses, thereby limiting the inadvertent spread of infected attachments. The Barracuda Exchange Antivirus Agent
only scans messages with attachments, including embedded messages with attachments. It does not scan text-only attachments (such as
HTML), message headers, bodies, or in-line attachments. Mail that has already been scanned by the Barracuda Spam Firewall is also scanned
by the Barracuda Exchange Antivirus Agent.
Important Notes
With this version of the Barracuda Exchange Antivirus Agent, messages that are deemed malicious are deleted and will not be
quarantined.
You cannot run multiple Barracuda Exchange Antivirus Agent engines at the same time on the same server. You can,
however, have a Microsoft Server Antivirus engine and one Barracuda Exchange Antivirus Agent engine running on the same
server.
If you have a Microsoft Server Antivirus engine running with the Barracuda Exchange Antivirus Agent engine, then you need to
exempt the following directories and files from the Microsoft Server Antivirus scan:
C:\Program Files\Barracuda
C:\Windows\Temp\BAR*.*
You can download the transport agent as described below from your Barracuda Spam Firewall and install it on all Exchange servers with the Hub
Transport role. If you want to scan outbound mail for viruses, you also need to install the agent on Exchange servers with the Edge Transport
role. The Barracuda Exchange Antivirus Agent updates virus signatures hourly and scans messages:
between local mailboxes
between the Internet and local mailboxes
Microsoft Exchange Server does not support the Barracuda Spam Firewall quarantine tool for viewing infected messages, information
on false positives, or other infected message details. All threat statistics that Microsoft Exchange Server provides to the Barracuda
Exchange Antivirus Agent are listed in the Exchange Antivirus Statistics section of the ADVANCED > Exchange Antivirus page on
the Barracuda Spam Firewall web interface.
Download and Install the Agent
Exchange Server versions lower than 2013 are not supported by the Barracuda Exchange Antivirus Agent 7.1. If you have not previously installed
a version of the Barracuda Exchange Antivirus Agent, you will not see the option to update an earlier version of the agent. The following image
shows how the selections might appear when there is a previous version of the Barracuda Exchange Antivirus Agent installed.
To install the Barracuda Exchange Antivirus Agent on Exchange Server 2013, you must be a member of an Exchange Server Organization
Management security group. If you have recently added yourself to this group, please log out before re-running the installer. Before installing the
Barracuda Exchange Antivirus Agent, set the Automatic Update option to On for Virus Definitions on the ADVANCED > Energize Updates pa
ge on the Barracuda Spam Firewall. Next, perform the following steps:
1. Log into Microsoft Exchange Server as an administrator.
2. Use the browser on your Microsoft Exchange Server to connect to the Barracuda Spam Firewall web interface.
3.
99
3. Log into Barracuda Spam Firewall as admin and navigate to the ADVANCED > Exchange Antivirus page.
4. In the Exchange Antivirus Agent section, click Download for the Barracuda Exchange Antivirus Agent that works with your version of
Exchange Server.
5. Run the Windows Installer. Follow the setup wizard instructions.
6. Click Finish when the wizard completes installing the agent. Once installed, the Barracuda Exchange Antivirus Agent is active and
begins providing virus protection.
After you have installed the Barracuda Exchange Antivirus Agent, refresh the ADVANCED > Exchange Antivirus page to view a list of
Exchange Servers in a table in the Exchange Antivirus Configuration section. The table will look something like this:
Field
Description
Hostname
The names of Exchange Servers on which the Barracuda Exchange
Antivirus Agent is installed.
Agent Version
The version of the Barracuda Exchange Antivirus Agent installed on
the Exchange Server.
Updated
This field does not apply to the currently installed version of the
Barracuda Exchange Antivirus Agent. For earlier versions, a value of
Yes indicates that the Barracuda Exchange Antivirus Agent is
communicating with the Barracuda Spam Firewall. If this field shows
No for an earlier version, it might indicate a brief period of
non-communication. Typically, the field refreshes to Yes as the
Barracuda Spam Firewall updates the Barracuda Exchange Antivirus
Agent. If the value remains No, check network connectivity between
your Exchange Server and the Barracuda Spam Firewall.
Exchange Antivirus Agent Statistics
The Barracuda Exchange Antivirus Agent 7.1.x collects and reports the following statistics:
Statistic
Description
Items Scanned
Total number of messages scanned, including infected messages.
Attachments Scanned
Number of files scanned, including those attached to infected
messages.
If an earlier version of the Barracuda Exchange Antivirus Agent is enabled to scan mail on an Exchange Server, the antivirus agent reports the
following statistics:
Statistic
Description
Messages Processed
Number of messages scanned by the Barracuda Exchange Antivirus
Agent.
Messages Quarantined
Number of messages that the Barracuda Exchange Antivirus Agent
quarantined, whether or not the message was delivered.
Files Scanned
Number of attachments scanned.
Files Quarantined
Number of attachments quarantined.
Queue Length
Number of messages waiting to be scanned.
Folders Scanned in Background
Number of folders processed by background scanning (versus
proactive scanning).
Messages Scanned in Background
100
Number of messages processed by background scanning (versus
proactive scanning).
Uninstalling the Exchange Antivirus Agent
If, after uninstalling the agent, the Information Store does not restart, see this Microsoft support article: https://support.microsoft.com/en-us/kb/32
3664. Some registry keys may not be removed/modified upon the uninstallation of the agent. Barracuda recommends that administrators back up
the registry before uninstalling the agent.
101
How to Get and Configure the Barracuda Exchange Antivirus Agent 6.0.x
en
This article refers to Barracuda Spam Firewall firmware 6.1.x through 7.0.x. Before installing the Barracuda Exchange Antivirus
Agent, it is recommended that you review all settings and options as shown below in Exchange Antivirus Settings. The Barracuda
Exchange Antivirus Agent 6.0.x supports Microsoft Exchange Server versions 2007 and 2010. Note that the Barracuda Exchange
Antivirus Agent no longer supports Microsoft Exchange Server version 2003.
What is the Barracuda Exchange Antivirus Agent?
The Barracuda Exchange Antivirus Agent is an add-in that you can download from your Barracuda Spam Firewall and install on your Microsoft
Exchange mailbox server(s). The add-in works together with Microsoft Exchange Server to scan messages for viruses and only provides data
about infected messages that is made available by the Exchange Server. The Barracuda Exchange Antivirus Agent provides constantly updated
virus signatures and does the scanning. Exchange does not provide a quarantine tool for viewing infected messages, information on false
positives or other infected message details. All threat statistics provided to the Barracuda Exchange Antivirus Agent by Exchange are listed in the
Exchange Antivirus Add-in Statistics section on the ADVANCED > Exchange Antivirus page of the Barracuda Spam Firewall web interface.
For infected file name information, see the MS Windows Event Log. To view performance of virus scanning on your Exchange server, use the MS
Windows Performance Monitor.
Download and Install the Agent
You must be a member of an Exchange Server Organization Management security group in order to install the Barracuda Exchange Antivirus
Agent on Exchange Server 2010. To install the Barracuda Exchange Antivirus Agent on Exchange Server 2007, you must be a member of an
Exchange Organization Administrator security group. Before installing the Barracuda Exchange Antivirus Agent on Exchange Server 2007 or
2010:
Barracuda Networks recommends that you review all settings and options as shown below in the Exchange Antivirus Settings section.
Set the Automatic Update option to On for Virus Definitions on the ADVANCED > Energize Updates page on the Barracuda Spam
Firewall.
To install the Barracuda Exchange Antivirus Agent on Exchange Server 2007 or 2010:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Log into Exchange Server as an administrator.
Use the browser on your Exchange Server to connect to the Barracuda Spam Firewall web interface.
Log into Barracuda Spam Firewall and navigate to the ADVANCED > Exchange Antivirus page.
In the Exchange Antivirus Agent section, click Download for the Barracuda Exchange Antivirus Agent that works with your version of
Exchange Server.
Run the Windows Installer and follow the setup wizard instructions.
Click Finish when the wizard completes installing the agent. After it is installed, the Barracuda Exchange Antivirus Agent is active and
begins providing virus protection.
Click Next. The Virus Definitions will now be installed on your Exchange Server by the Barracuda Spam Firewall.
When the progress bar shows complete, click Next The Barracuda Spam Firewall installs the configuration on your Exchange Server.
Click Finish when the progress bar shows complete. The agent is now configured. At this point, the Barracuda Exchange Antivirus Agent
has been loaded by the Exchange Server and scanning has begun according to the configured settings.
Configure the Agent on Microsoft Exchange
Note that if the configuration process is interrupted and does not complete, it can be rerun from the Start Menu, or it will reopen each time
Windows is restarted until configuration is completed (or the product is uninstalled).
1. When prompted on Exchange Server, enter the URI (must be https) of your Barracuda Spam Firewall, along with the Passtoken shown
on the ADVANCED > Exchange Antivirus page in the Exchange Antivirus Agent section.
2. Click Next. The Virus Definitions will now be installed on your Exchange Server by the Barracuda Spam Firewall.
3. Click Next when the progress bar shows complete. The Barracuda Spam Firewall will install the configuration on your Exchange Server.
4. Click Finish when the progress bar shows complete. The Barracuda Exchange Antivirus Agent is now configured. At this point, the
Barracuda Exchange Antivirus Agent has been loaded by the Exchange Server and scanning has begun according to the configured
settings.
Exchange Antivirus Settings
After you have installed and configured the Barracuda Exchange Antivirus Agent per the above steps, you'll see your Exchange Server listed in
the table in the Exchange Antivirus Settings section of the ADVANCED > Exchange Antivirus page on the Barracuda Spam Firewall listing
the following:
Hostname - The hostname of your Exchange Server.
Version - The version of the installed Barracuda Exchange Antivirus Agent.
Updated - A value of Yes indicates that the Barracuda Exchange Antivirus Agent is communicating with the Barracuda Spam Firewall. If
this field shows No, it might indicate a brief period of non-communication. Typically the field will refresh to Yes as the Barracuda Spam
Firewall sends the Barracuda Exchange Antivirus Agent an update. If the value remains No, check network connectivity between your
102
Exchange Server and the Barracuda Spam Firewall.
Configuring Exchange Antivirus Settings for Exchange Server 2007/2010
Barracuda Networks considers that the default configuration settings, managed from the ADVANCED > Exchange Antivirus page of the
Barracuda Spam Firewall, are acceptable for most environments and recommends that they only be changed with caution.
Setting
Description
Enabled
Yes enables the Barracuda Exchange Antivirus Agent to scan mail
on the Exchange Server after the agent has been successfully
installed. Disabling the scanner (setting Enabled to No) does not
disable all related Windows services. To permanently remove the
Barracuda Exchange Antivirus Agent, you must uninstall it on
Exchange Server.
Scan RTF Message Bodies
Rich Text Format (RTF) is used primarily by Microsoft Outlook for
internal messages. Set to Yes to scan these types of messages. If
you select No, only HTML and plain text message bodies will be
scanned, while RTF messages will not.
On-Access Scanning
This type of scan occurs when a client requests data that has not yet
been scanned (i.e. on-demand). Select Yes to enable.
Scan Outbound Messages
If your outbound message traffic is scanned by another service (e.g.
the Barracuda Spam Firewall), then this feature can be disabled to
reduce load on your Exchange Server.
Timeout
Number of seconds to wait for a scan before Exchange Server times
out and returns an error to the mail client.
Proactive Scanning
This type of scan occurs in the background and applies to new
messages that have arrived in the message queue but have not yet
been read.
Background Scanning
Background scanning occurs on a low-priority basis and applies to
older data that has not yet been scanned using the newest virus
definitions. Set to No to reduce load on your Exchange Server, but
infected messages that are delivered before the newer virus
definitions are able to detect them won't be later rescanned and
quarantined.
Scanning Cutoff
Maximum age of message, in hours, to re-scan messages when virus
definitions are updated. Lowering this value can reduce the load on
your Exchange Server, but it can also increase the risk of failing to
quarantine late-breaking infections.
Infected Messages Retention
Time period, in hours, that the Barracuda Exchange Antivirus Agent
waits after an infected message is quarantined before deleting it.
Consider the longest time period that users would not check their
email, but also consider that a higher value could impact
performance on the Exchange Server. If the value is too low (shorter
time), the system may not deliver false positives (i.e., 'good' mail) that
the user might want to receive.
Only Scan Attachments
This setting applies to background scanning of messages. Setting to
Yes indicates to scan only attachments, not message bodies.
Only Scan Unscanned Messages
When set to Yes, Exchange Server scans messages in the
background that have never been scanned before rather than
rescanning messages when virus definitions are updated.
Removing the Barracuda Exchange Antivirus Agent
To remove the Barracuda Exchange Antivirus Agent for a particular Exchange server, you must first uninstall the add-in from that Exchange
Server. Next, log into the Barracuda Spam Firewall web interface as admin. From the ADVANCED > Exchange Antivirus page, click the trash
can icon for the Exchange Server hostname in the table in the Exchange Antivirus Agent Settings section. This will remove the Exchange
Server from the statistics and threats reports on the page.
103
Virus Checking and Notifications
en
Virus scanning is automatically enabled on the Barracuda Spam Firewall and the system checks for definition updates on a regular basis (hourly
by default). Virus Scanning takes precedence over all other mail scanning techniques and is applied even when mail passes through the
Connection Management layers. As such, even email coming from “whitelisted” IP addresses, sender domains, sender email addresses or
recipients are scanned for viruses and blocked if a virus is detected.
Use the BASIC > Virus Checking page in the web interface to enable or disable virus checking. If you enable Barracuda Real-Time Protection,
the Barracuda Spam Firewall will check unrecognized spam and virus fingerprints against the latest virus threats logged at Barracuda Central that
have not yet been downloaded by the Barracuda Spam Firewall Energize Updates. See the online help on the BASIC > Virus Checking page for
more details about this setting.
Extended Malware Protection (Available on model 600 and higher)
With version 6.1 and higher, Barracuda offers a subscription to provide additional anti-malware scanning with the Avira virus scan engine. To
subscribe, see the Subscription Status section of the BASIC > Dashboard page.
Internal Virus Scanning For Your Microsoft Exchange Mail Server
The Barracuda Spam Firewall offers an add-in that you can download from the web interface and install on your Microsoft Exchange Server to
provide internal virus scanning within your network. The Barracuda Exchange Antivirus Agent runs as a Windows service on your 2003, 2007
or 2010 MS Exchange Server and works together with MS Exchange to scan internal mail traffic for viruses. Scanning is based on constantly
updated virus signatures from the Barracuda Spam Firewall.
Any time a new virus signature is released, the Barracuda Exchange Antivirus Agent will scan all internal mail traffic for that virus as well as mail
previously stored on the server, depending on how you configure settings for the agent. See the ADVANCED > Exchange Antivirus page on the
Barracuda Spam Firewall web interface or see How to Get and Configure the Barracuda Exchange Antivirus Agent 6.0.x for instructions on
downloading and configuring the add-in for your organization’s needs.
Attachment Block Notifications
You can enable or disable notification emails to senders of messages that are blocked due to file attachment content filters. Configure these
notifications for inbound and outbound mail from the ADVANCED > Bounce/NDR Settings page in the web interface. From this page you can
also enter custom message text to insert in the notifications. Attachment content filters are configured in the Attachment Content Filters section of
the BLOCK/ACCEPT > Content Filters page.
Spam and Quarantine Notifications
Separate non-delivery notifications (NDR) can be configured to alert the sender when a message is blocked or quarantined due to spam scoring
or policy (content filtering). See Non-Delivery Reports (NDRs) for more information.
104
How Spam Scoring Works
en
As a message passes through the last of all of the defense layers, it is scored for spam probability. This score ranges from 0 (definitely not spam)
to 10 or higher (definitely spam). Based on this score, the Barracuda Spam Firewall either tags (inbound messages only), quarantines, blocks or
allows (or sends, for outbound) the message.
Once you have more experience with the Barracuda Spam Firewall, you can adjust how aggressively the system deals with spam. For example,
you may decide to tag (inbound only) or quarantine spam instead of blocking it. Details of spam scoring limits for your Barracuda Spam Firewall
are discussed in the Help file on the BASIC > Spam Checking page.
On the Barracuda Spam Firewall 400 or higher you can set the spam scoring values on a per-domain basis, and these scoring values
take precedence over the global spam scoring settings. On the Barracuda Spam Firewall 600 and higher, spam scoring can be set on a
per-user basis (inbound only), from the DOMAINS tab. For more information about per-domain settings, see Creating and Managing
Domains. For more about per-user settings, see Creating and Managing Accounts.
105
Monitoring Inbound and Outbound Email Traffic
en
Monitor and Classify Incoming Emails
Once email is flowing through the Barracuda Spam Firewall, the administrator can view the BASIC > Message Log page to get an idea of how
many messages are being blocked, quarantined, tagged or allowed, with reasons for each of those actions. Reviewing this log will give an idea of
how current settings are filtering messages, and the page enables adding or removing message senders to or from the whitelist. See the Messag
e Log for more information, and, for details on filtering messages in the log, see the online help on the BASIC > Message Log page.
If you enable Bayesian filtering on the BASIC > Spam Checking page, you will then see Spam and Not Spam buttons on the BASIC > Message
Log page in the tool bar. Use these actions to train the Bayesian database. Bayesian training works only on messages with 11 words or more.
With Bayesian filtering enabled, if a message is not classified as spam by the Barracuda Spam Firewall, but it appears to be spam, you can elect
to submit that message to Barracuda Central from the BASIC > Message Log page. For best Bayesian accuracy, it is recommended that you
reset your Bayesian database every 6 months. Note that Bayesian filtering is turned off by default.
See Advanced Inbound Email Filtering Policy for more details on using the Message Log with Bayesian filtering, and creating custom whitelists
and blocklists to allow or block messages from specific IP addresses, domains or email accounts.
Monitor and Classify Outgoing Emails
If you have configured the Barracuda Spam Firewall to filter outbound mail, watch the log on the BASIC > Outbound Quarantine page. Based
on Outbound Spam Scoring Limits you specify on the BASIC > Spam Checking page, as well as any Block/Accept filters you configure,
outbound messages will be quarantined or blocked as needed and listed on the BASIC > Outbound Quarantine page. Look for false positives
and adjust spam scoring accordingly. Any message listed in the outbound quarantine can be delivered, whitelisted, deleted, or rejected by an
administrator.
106
Performance and Email Statistics
en
The BASIC > Dashboard page provides an overview of the health and performance of your Barracuda Spam Firewall, including:
Hourly and daily email statistics that display the number of inbound and outbound messages blocked, tagged (inbound messages only),
quarantined, sent (outbound messages only), redirected (outbound messages only), encrypted (outbound only), rate controlled and
allowed (inbound only) for the last 24 hours and 28 days.
The subscription status of Energize Updates.
Performance statistics, including CPU temperature and system load. Performance statistics displayed in red signify that the value
exceeds the normal threshold. These values will fluctuate based on the amount of traffic that is being handled, but if any setting remains
consistently in the red for a long period of time, please contact Barracuda Networks Technical Support.
Product Tips
At the top of the BASIC > Dashboard page you’ll see the Product Tips bubble. This space is populated with usage tips, new programs and
features from Barracuda Networks specific to your product, and with a link to the release notes for the latest firmware update. These tips are
updated frequently from Barracuda Central.You have the following options in managing this feature:
To hide a particular message permanently, click the Hide link.
To hide the Product Tips section of the page, set Show Product Tips in the Product Tips section of the BASIC > Administration page
to No.
Email Statistics - Inbound
This section of the BASIC > Dashboard page summarizes how inbound mail traffic is handled by the Barracuda Spam Firewall based on how
you have configured the system. Actions reported include Blocked, Blocked:Virus, Rate Controlled, Quarantined, Allowed:Tagged and Allowed.
Statistics are tallied by hour, by current calendar day starting at midnight, and total since installation (or since the last reset).
If you have not configured any domains for receiving inbound mail on the DOMAINS page, and you configure the Barracuda Spam Firewall only
for processing outbound mail, it is possible to see some messages logged as inbound mail traffic. For example, if a message is received
addressed to the default domain configured under BASIC > IP Configuration page, then the email will be counted as an inbound message.
Email Statistics - Outbound
Outbound mail traffic is summarized in this table on the BASIC > Dashboard page much the same way as inbound traffic, except that a count of
outbound message Blocked due to custom policy or spam are reported separately, outbound messages are not tagged, and messages counted
as Sent are the counterpart of inbound Allowed messages.
If you have not configured the Barracuda Spam Firewall for outbound mail and only expect inbound mail, it is still possible to see some messages
logged as outbound traffic. If a spammer tries to relay a message through the Barracuda Spam Firewall by spoofing a valid domain as the sender
to an invalid recipient, the Barracuda Spam Firewall will block the message and it will appear in the outbound email statistics table as Blocked.
As an example, consider that mydomain.com is configured as a valid domain on the DOMAINS page and badomain.com is not. A spammer
sends a message from [email protected] to the IP address of the Barracuda Spam Firewall, addressed to [email protected]. T
he message will show as Blocked with a reason of ‘invalid domain’ in the Message Log and will be included in the outbound mail Blocked
statistics.
107
Quarantine: An Overview
en
Using Quarantine is Optional
By default, the Barracuda Spam Firewall does not quarantine incoming or outgoing messages, but you may want to enable quarantine for
inbound mail, at least, because it offloads storage of potential spam from the mail server and backups. It also keeps potential spam messages out
of the user’s inbox. While some organizations require quarantine behavior, tagging inbound messages that might be spam is recommended over
quarantining them for several reasons:
With tagging of inbound messages, the user doesn’t need an additional inbox for storing quarantined messages because the potential
spam message is delivered to their regular inbox with a special word or phrase prepended to the Subject line to indicate that it has been
tagged as potential spam. These messages can be filtered to a special mailbox if the user desires, or can be viewed or deleted from their
regular inbox.
Tagging inbound messages on the Barracuda Spam Firewall saves system resources because the message is not stored on the
appliance itself; it’s sent on to the user’s mailbox or to an administrator’s mailbox to manage.
Note that, by enabling quarantine of incoming messages identified as possible spam, either the user or the administrator is required to
maintain the quarantine inbox and settings.
Quarantine of inbound mail can be enabled or disabled in the Spam Scoring Limits section on the BASIC > Spam Checking page as well as on
various BLOCK/ACCEPT pages. If enabled, you can select either Global quarantine or Per-User quarantine.
For more information on using inbound quarantine, see Managing Inbound Quarantine.
Quarantine of Outbound Mail
Enable or disable in the Outbound Spam Scoring Limits section on the BASIC > Spam Checking page and set up filtering criteria for
outbound quarantine on various BLOCK/ACCEPT pages. Outbound quarantined mail can be logged and managed at the per-domain level as
well as at the global level.
For more information on using outbound quarantine, see Managing Outbound Quarantine.
108
Mail Journaling
en
Journaling allows you to record a copy of, or journal of, email communications in your organization and send them to a dedicated mailbox on your
Barracuda Message Archiver, Microsoft Exchange Server or other archiving solution. The process of journaling is different from archiving.
Journaling is simply a means of recording your users’ messages. Archiving, on the other hand, is a means of storing those copies in a separate
environment for the purpose of regulatory compliance, data retention, or server maintenance.
Enable Journaling on the Barracuda Spam Firewall
To enable simple journaling of every non-blocked inbound or outbound message that is delivered by the Barracuda Spam Firewall, configure the
following in the Mail Journaling section of the BASIC > Administration page:
1. Enter a Destination Email Address. This address should be reserved only to receive these journaled email copies and not for receiving
other types of emails. Note that no message body is available for outbound messages that are encrypted by the Barracuda Spam
Firewall. If you are using a Barracuda Message Archiver, see Journaling to the Barracuda Message Archiver below.
2. Enter a Bounce Address to which email messages will be sent that the Barracuda Spam Firewall could not deliver to the journal
account - either because the receiving server for the Destination Email Address was unavailable or because the server refused the
message. In no event will a bounce message be sent to the original sender.
3. Decide whether or not to journal all messages processed by the Barracuda Spam Firewall, including potential spam. If you have enabled
Per User Quarantine and do not want to journal messages that are quarantined, then set Do Not Journal Per-User Quarantined
Email to Yes. This means that messages arriving in user quarantine inboxes will not be journaled at that time. If, however, the
quarantined message is then manually delivered from the global Message Log, the domain Message Log, the Outbound Quarantine or
the user's quarantine inbox, the message will be journaled. Setting this option to No means that ALL messages processed by the
Barracuda Spam Firewall will be journaled if you provide a Destination Email Address in this section.
Journaling to the Barracuda Message Archiver
1. Enable mail journaling as described above.
2. On the Barracuda Message Archiver, configure the IP address and TCP Port of your destination mail server on the ADVANCED > SMTP
Configuration page so that incoming messages will be forwarded to your email server.
See also:
How to Configure Your Barracuda Message Archiver to Act as an SMTP Proxy to Your Email Server
Understanding Email Encryption and Archival
Understanding Microsoft Exchange 2013 Journaling
Microsoft Exchange Server 2007 and 2010 Journaling
How to Set Up Email Journaling
109
How to Migrate From Postini to the Barracuda Spam Firewall
en
Barracuda strongly recommends consulting with your reseller or a Barracuda sales representative prior to migration. To migrate your list of users
and domains from Postini to the Barracuda Spam Firewall:
en
Add Domains
Add Users
Add Policies
Add Domains
1. Export your domains from Postini to a CSV file.
2. Add the domains. You can either manually add each domain or add multiple domains at one time.
To manually add each domain, go to the DOMAINS > Domain Manager page.
To add all of your domains at one time from the CSV file, use the Barracuda Spam Firewall API. For more information, see the U
se Case – Adding and Configuring Multiple Domains section in the Barracuda Spam Firewall API Guide.
3. Configure the per-domain and per-user settings for each domain. On the DOMAINS > Domain Manager page, click Manage Domain f
or each domain that you are configuring. The default destination server for the domains is configured in the Server Name/IP field on
the BASIC > IP Configuration page.
Add Users
1. Export your list of user email accounts from Postini to a CSV file, with one address per line.
2. Add users. You can add all of your users at one time from the CSV file with either the Barracuda Spam Firewall web interface or
the Barracuda Spam Firewall API.
In the Barracuda Spam Firewall web interface, go to the USERS > User Add/Update page, paste the contents of your CSV file
into the User Account(s) text box, and then click Save Changes.
If you prefer to use the Barracuda Spam Firewall API, use the user.create method in a loop with a Java, Perl, or similar type
of script. For details, see the Barracuda Spam Firewall API Guide.
3. On the USERS > User Add/Update page, configure the following settings for all of the users that you have created:
Enable User(s) Quarantine – Select Yes to create a quarantine account for users, or No to disable specified quarantine
accounts. Disabled quarantine accounts will not quarantine any new messages, but any pre-existing quarantined messages will
still be accessible. Any user preferences (such as Whitelist/Blocklist) allowed to users by the administrator will also be available.
Email New User(s) – Email new account login information to users when their users accounts are created. For details, click He
lp on the USERS > User Add/Update page.
Managing Multiple Quarantine Inboxes with One Primary Account
Users can only be added as the primary address (no aliases). To manage multiple quarantine inboxes with one primary account if you
are using per-user quarantine, use the Alias Linking feature. You can enter multiple email addresses to be linked (aliased) to that
primary account. Create aliases on the ADVANCED > Explicit Users page. For more information about the Alias Linking feature, see
Quarantine Options. For more details about adding and managing users, see Creating and Managing Accounts.
Add Policies
To configure policies for the users and domains that you have added, go to the pages under the BLOCK/ACCEPT tab. To add multiple policies at
one time (e.g., add multiple blocked domains), click Bulk Edit on these pages.
110
Routing Outbound Mail
en
In this Section
About Scanning of Outbound Mail
How to Route Outbound Mail from the Barracuda Spam Firewall
How to Configure Office 365 for Inbound and Outbound Mail
How to Configure Google Apps for Inbound and Outbound Mail
How to Route Outbound Mail from Kerio Connect Mail Server through the Barracuda Spam Firewall
Encryption of Outbound Mail 6 and Above
Encryption of Outbound Mail 5.x
See also SMTP Error Codes.
111
About Scanning of Outbound Mail
en
The Barracuda Spam Firewall may be configured to scan outgoing mail simultaneously with scanning inbound mail. Virus Scanning and Rate
Control are applied to outbound mail as well as the following filters, if specifically enabled, which are configurable from the BASIC > Spam
Checking and BLOCK/ACCEPT pages:
Spam Scoring, with Block or Quarantine actions
IP Address Filtering
Sender Domain Filtering
Sender Email Address Filtering
Recipient Filtering
Content Filtering (Subject, Header and Body)
Attachment Filtering
Image Analysis
Intent Analysis
The following scanning tools are not applied to outbound mail:
SPF (Sender Policy Framework), a sender authentication mechanism
DKIM (DomainKeys), an email authentication system designed to verify the DNS domain of an email sender
Regional Settings, the application of special spam analysis rules for particular languages
Per-user Whitelist/Blocklist
Per-domain Whitelist/Blocklist
IP Reputation checks
These are the policies that can be applied to outbound mail using the BLOCK/ACCEPT pages:
Encryption (see Encryption of Outbound Mail 6 and Above)
Quarantine (see Managing Outbound Quarantine)
Block
Redirection
To scan outgoing mail with the Barracuda Spam Firewall, you must configure outbound operation on the BASIC > Outbound page (see How to
Route Outbound Mail from the Barracuda Spam Firewall). There you’ll specify your trusted outbound mail server IP address or domain name
(either your mail server or another trusted relay), identify a Smart host if you have one, and, optionally, an authentication type. The Barracuda
Spam Firewall supports SMTP/SASL authentication and LDAP. If you are relaying though a Smart host, you must also configure the Smart host
to send to the Internet.
Be aware that configuring the Barracuda Spam Firewall to scan outbound as well as inbound mail will increase the load on the system. You may
find that you need to upgrade your Barracuda Spam Firewall to another model.
Note:
When configuring outbound mail, ensure that your network firewall blocks all port 25 traffic that doesn't originate from your Barracuda
Spam Firewall.
112
How to Route Outbound Mail from the Barracuda Spam Firewall
en
It is recommended that you see About Scanning of Outbound Mail before proceeding.
If you are using Google Apps Business and Education editions with the Barracuda Spam Firewall as your outbound mail
gateway, please see How to Configure Google Apps for Inbound and Outbound Mail in addition to reading this article.
If you are deploying the Barracuda Spam Firewall on Amazon Web Services, please see Routing Mail Through Amazon
Web Services in addition to this article.
You can relay outbound mail through the Barracuda Spam Firewall simultaneously with scanning inbound mail, where outbound mail will be
subject to the same spam and virus scanning and, for the most part, the same custom policy as inbound mail with some exceptions.
The following scanning tools are not applied to outbound mail:
IP Reputation, a sender authentication mechanism
SPF (Sender Policy Framework), a sender authentication mechanism
DKIM (DomainKeys), an email authentication system designed to verify the DNS domain of an email sender
Per-user Whitelist/Blocklist
Per-domain Whitelist/Blocklist
To relay outbound mail to the Barracuda Spam Firewall:
In most cases, the only thing that needs to be done is to enter the IP address of the outgoing mail server or other trusted relay server in the Relay
Using Trusted IP/Range field on the BASIC > Outbound page, as described in Simple configuration of outbound relay of mail below. Outb
ound mail is scanned for spam, as is inbound mail, as well as filtered for policies you create from the BLOCK/ACCEPT filtering pages.
If you need to configure additional options for outbound relay, see the online help on the BASIC > Outbound page.
Simple configuration of outbound relay of mail
1. Configure your mail server to relay outbound mail to the Barracuda Spam Firewall. If you have a Microsoft Exchange Server, enter your
Smart host IP address in the next step and configure the Smart host on your mail server to relay outgoing mail to the Barracuda Spam
Firewall.
2. Enter the IP address or host/domain name of your default mail server or another trusted relay server that can relay outbound mail
through the Barracuda Spam Firewall to the Internet. Use the Relay Using Trusted IP/Range and/or the Relay Using Trusted
Host/Domain fields.
Warning
To protect your system against domain spoofing, it is strongly recommended to use IP addresses and NOT domain names for
specifying Trusted Relays. As such, it is recommended to specify your mail server and/or trusted outbound relay servers in the
Relay Using Trusted IP/Range field as opposed to specifying a host/domain name
However, if you are using the Relay Using Trusted Host/Domain field, it is recommended to configure either SMTP AUTH or LDAP
authentication on this page as well.
Note that LDAP Routing is available on the Barracuda Spam Firewall 600 and higher, configurable on the ADVANCED > LDAP Routing
page.
If using your default mail server to relay outbound mail through the Barracuda Spam Firewall, enter the IP address of your Destination
Mail Server as specified on the BASIC > IP Configuration page or in the DOMAINS > Manage Domain > BASIC > IP Configuration p
age per-domain setting.
The following steps cover additional options for outbound relay:
3. To configure the Barracuda Spam Firewall to relay outgoing mail through your normal outbound SMTP host or Smart host to the Internet,
enter the IP address or hostname and TCP port in the Outbound SMTP Host/Smart Host fields. This is the destination server through
which outbound email will be sent from the Barracuda Spam Firewall for routing to the Internet, and whose IP address will appear in the
outgoing mail headers.
4. To enforce using a secure TLS connection to send mail through the Barracuda Spam Firewall (inbound and outbound) for all domains,
set Force TLS to Yes. SMTP over TLS/SSL defines the SMTP command STARTTLS. This command advertises and negotiates an
encrypted channel with the peer for this SMTP connection. This encrypted channel is only used when the peer also supports it.
5. To authenticate senders of outbound email, specify the authentication type in the Enable SASL/SMTP Authentication field. (SASL is
the Simple Authentication and Security Layer, a method for adding authentication support to connection-based protocols. To use SASL,
a protocol includes a command for identifying and authenticating a user to a server and for optionally negotiating protection of
subsequent protocol interactions.)
113
SMTP AUTH Proxy - SMTP AUTH/SASL authentication enables the SMTP "AUTH" command to authenticate users before
allowing them to relay outgoing mail through this Barracuda Spam Firewall. Either set Use Destination Mail Server as SMTP
AUTH Proxy to Yes or fill in the IP address of another proxy server that is set up to support the SMTP AUTH authentication
command (e.g. MS-Exchange or Sendmail) to authenticate senders of outbound mail. To use this authentication method, you
must also enable 'Use name and password' or a similar option in your email client. Also, since the password transmits in
cleartext, it is recommended to secure transmission by enabling SMTP over TLS on the ADVANCED > Email Protocol page on
LDAP - Use your LDAP directory to authenticate senders. Fill in the LDAP settings as described below.
6. To limit outbound relay capability to certain users or domain names, enter them in the Senders With Relay Permission field. To prevent
against domain spoofing, it is recommended not to specify sender email address or domain names that can relay outbound mail through
the Barracuda Spam Firewall. Please use this setting only for trusted senders, and note that it is recommended to use one of the sender
authentication methods described above as well for added security.
Basic Outbound/Relay Settings
Outbound SMTP Host (Smart host) - The IP address or host name of the destination server through which outbound email will be sent
from the Barracuda Spam Firewall for routing to the Internet, and whose IP address will appear in the outgoing mail headers.
Port - The TCP port of your SMTP host or Smart host through which you want to relay outbound mail.
Username - Only necessary if required for authentication with the SMTP host or Smart host.
Password - Only necessary if required for authentication with the SMTP host or Smart host.
Force TLS - (Optional): Set to Yes if you want to enforce using a secure TLS connection for all mail leaving the Barracuda Spam Firewall
(inbound and outbound). SMTP over TLS/SSL defines the SMTP command STARTTLS. This command advertises and negotiates an
encrypted channel with the peer for this SMTP connection. This encrypted channel is only used when the peer also supports it.
To configure relay using authentication and other relay options, see the online help for the BASIC > Outbound page.
114
How to Configure Office 365 for Inbound and Outbound Mail
en
This article addresses configuring Microsoft®Office 365™ with the Barracuda Spam Firewall as your inbound and/or outbound mail
gateway.
See also: Step 3 - Initial Configuration
You can specify the Barracuda Spam Firewall as an inbound mail gateway through which all incoming mail for your domain passes before
reaching your Office 365 account. The Barracuda Spam Firewall filters out spam and viruses, and then passes the mail on to the Office 365 mail
servers. Use the Inbound Configuration instructions below to configure.
You can likewise specify the Barracuda Spam Firewall as the outbound mail gateway through which all mail is sent from your domain via your
Office 365 account to the recipient. As the outbound gateway, the Barracuda Spam Firewall processes the mail by filtering out spam and viruses
and applying any outbound policies (blocking, encrypting, etc.) before final delivery. By using the configuration described in Outbound
Configuration below, you instruct the Office 365 mail servers to pass all outgoing mail from your domain to the Barracuda Spam Firewall.
Office 365 addresses can change, so please refer to Microsoft documentation. To prepare your Barracuda Spam Firewall deployment
to connect with Office 365, see Prerequisites for your email server environment in Set up connectors to route mail between Office
365 and your own email servers.
Inbound Configuration
To restrict all mail sent to your organization to only that which is sent from the Barracuda Spam Firewall:
1.
2.
3.
4.
Click Admin.
Click Exchange, and then to go to the Exchange Admin Center.
Click Mail Flow, and click Connectors. If any connectors already exist for your organization, you can see them listed here.
To start the wizard, click the plus symbol +. Use these options during setup:
5. Add the IP address of the Barracuda Spam Firewall. Any Internet mail that does not originate from this IP address range will be rejected
by Office 365.
115
6. Optionally add the requirement for TLS encryption by using this setting:
When you set these restrictions, all mail from your partner organization sent from the IP address or address range you specify must be
sent using TLS. Any mail that does not meet this restriction will be rejected.
For further details about configuring Office 365 with connectors, see Set up connectors for secure mail flow with a partner organization in
Microsoft documentation.
Outbound Configuration
1.
2.
3.
4.
Log into the Office 365 Portal
Navigate to Admin > Exchange to go to the Exchange Admin Center.
Click Mail Flow.
Click Connectors. If any connectors already exist for your organization, you can see them listed here.
116
Before you set up a new connector, check any connectors that are already listed here for your organization. For example, if you ran the Exchange
Hybrid Configuration wizard, connectors that deliver mail between Office 365 and Exchange Server will be set up already and listed here (see Hy
brid Configuration wizard in Microsoft documentation). You don’t need to set them up again, but you can edit them here if you need to.
If you don’t plan to use the hybrid configuration wizard, or if you’re running Exchange Server 2007 or earlier, or if you’re running a non-Microsoft
SMTP mail server, set up connectors using the wizard. For more information, see Set up connectors to route mail between Office 365 and your
own email servers in Microsoft documentation.
The outbound mail gateway will be the IP address of the Barracuda Spam Firewall.
To use the wizard:
1. Click the plus symbol +.
2. On the first screen, choose the options that are depicted in the following screenshot, where To should refer to the Barracuda Spam
Firewall:
3. Click Next, and follow the instructions in the wizard.
4. Click the Help or Learn More links if you need more information.
The wizard will guide you through setup. At the end, make sure your connector validates. If the connector does not validate, double-click the
message displayed to get more information, and see Fixing connector validation errors in Microsoft documentation for help resolving issues.
Finally, in the Barracuda Spam Firewall web interface, see Simple configuration of outbound relay of mail in the help page of the BASIC > Outbo
und page to configure outbound mail, or follow the same instructions in How to Route Outbound Mail from the Barracuda Spam Firewall.
host name, hosted, Office 365
O365
ja
Barracuda Spam & Virus Firewall Plus/Office 365
Barracuda Spam & Virus Firewall PlusOffice 365Office 365
Barracuda Spam & Virus Firewall PlusOffice 365Barracuda Spam & Virus Firewall
PlusOffice 365
Related Articles
How to Route Outbound Mail from
the Barracuda Spam Firewall
Office 365
1.
2.
3.
4.
Office 365
> Exchange
Set Up Domain
add dns records
1. Barracuda Spam & Virus Firewall PlusOffice 365
1ourdomain.com.mail.protection.outlook.comPoints To AddressOffice 365
5. Barracuda Spam & Virus Firewall PlusWeb > IP
6. 2TCP/IP/IPBarracuda Spam & Virus Firewall PlusOffice 365Exchange Server
Barracuda Spam & Virus Firewall PlusDNSIP
ourdomain.mail.protection.outlook.com
2. Barracuda Spam & Virus Firewall Plus > IP
7. ourdomain.com
8. Office 365Barracuda Spam & Virus Firewall PlusOffice 365Exchange Server
1.
a. Exchange
b.
c. +...
3. Barracuda Spam & Virus Firewall Plus
117
c.
d.
e.
f.
g.
h.
i.
j.
...
*...... > IP
IPBarracuda Spam & Virus Firewall PlusIP > IP
+OK
*...... > SCLSpam Confidence LevelSCL
OK
1. Office 365
2. > Exchange
3.
4.
5. Barracuda Spam & Virus Firewall PlusIP
5: Office 365Barracuda Spam & Virus Firewall Plus
6. Barracuda Spam & Virus Firewall Plus
6: Barracuda Spam & Virus Firewall Plus
118
119
7. Barracuda Spam & Virus Firewall Plus > Simple configuration of outbound relay of mailHow to Route Outbound Mail from the Barracuda
Spam Firewall
host name, hosted
120
How to Configure Google Apps for Inbound and Outbound Mail
en
This article addresses configuring Google Apps Business and Education editions with the Barracuda Spam Firewall as your
inbound and/or outbound mail gateway.
Inbound Configuration
1. Log into the Google Apps Domain Management Portal.
2. Navigate to the Settings tab and then select Email under the Services section.
3. Navigate to Inbound Gateway and enter the public IP addresses of the Barracuda Spam
Firewall(s), specifying either the block of addresses or individual IP addresses.
Figure 1: Google Apps - Inbound Gateway Settings
Make sure to check the box: Only let users receive email from the email gateways listed above. All other mail will be rejected. More info
on inbound gateways can be found here.
Outbound Configuration
1. Navigate to the Settings tab and then select Email under the Services section.
2. Navigate to Outbound Gateway and enter the IP address of the Barracuda Spam Firewall that is the outbound mail gateway.
Figure 2: Google Apps - Outbound Gateway Settings
More information about outbound gateways can be found here.
Google Apps IP Addresses can change so please refer to this Google documentation.
Additional settings:
nslookup -q=TXT _netblocks.google.com 8.8.8.8
server: google-public-dns-a.google.com
address: 8.8.8.8
Non-authoritative answer:
_netblocks.google.com text ="v=spf1 ip4:216.239.32.0/19ip4:64.233.160.0/19ip4:66.249.80.0/20
ip4:72.14.192.0/18ip4:209.85.128.0/17ip4:66.102.0.0/20ip4:74.125.0.0/16
121
ip4:64.18.0.0/20ip4:207.126.144.0/20ip4:173.194.0.0/16 ?all"
Configuring the Barracuda Spam Firewall
1. Navigate to DOMAINS > Domain Manager and specify your domain in New Domain Name, then click Add Domain.
2. Click the Manage Domain link and then BASIC > IP Configuration. Add the Google Apps destination mail servers as follows:
Priority
Google Apps Destination Mail Server
1
ASPMX.L.GOOGLE.COM
5
ALT1.ASPMX.L.GOOGLE.COM
5
ALT2.ASPMX.L.GOOGLE.COM
10
ASPMX2.GOOGLEMAIL.COM
10
ASPMX3.GOOGLEMAIL.COM
Please also add the Destination Server name/IP address or hostname that receives email after spam and virus scans. It is usually best to
use a hostname rather than an IP address so that the destination mail server can be moved and DNS updated at any time without having
to make changes to the Barracuda Spam Firewall configuration.
If you set Use MX Records (on the same page) to Yes, you must enter a domain name for this field. If multiple servers are specified,
then the delimiter used determines the behavior (see below). Note that you can either configure Use MX Records for all domains from
the BASIC > IP Configuration page, or you can configure it per-domain from DOMAINS > Domain Manager > Manage Domains, the
n using the BASIC > IP Configuration page for the domain you choose to manage. It is NOT recommended to set Use MX Records t
o Yes to avoid a potential mail loop.
1. Comma (",") or semi-colon (";") - Each entry in the list will used in round-robin fashion, with relative weights determined by the
number of times a particular entry is listed.
2. Space (" ") - Each entry in the list will be treated as a failover list, with an entry being used only if all entries preceding it in the
list are unreachable.
For more information about what it means to use MX records, please see Using MX Records.
122
How to Route Outbound Mail from Kerio Connect Mail Server through the
Barracuda Spam Firewall
en
Use the following steps to route outbound mail from the Kerio Connect Mail Server
through the Barracuda Spam Firewall.
1. Navigate to the Kerio Connect directory, expand Configuration, and click SM
TP Server.
2. In the SMTP Delivery tab, select Use relay SMTP server, and enter the
Barracuda Spam Firewall IP address.
3. Enter the Relay server port number.
4. Turn on Use SSL/TLS if supported by remote SMTP server.
Related Articles
Kerio Connect Mail Server
Deployment
123
Encryption of Outbound Mail 6 and Above
en
In this article:
en
Overview
Encrypting Messages From the MS Outlook Client
Secured Message Contents
Configuring and Using Encryption
Archiving Encrypted Emails
Requirements for Using Encryption
Setting Encryption Policy for Outbound Mail
Branding
Encryption and Quarantine, Blocking and Queuing
Sending and Receiving Encrypted Messages
Recalling Encrypted Messages
Overview
For health care providers, governmental agencies and other entities who need to protect private, sensitive and valuable information
communicated via email, the Barracuda Spam Firewall allows creating multiple policies to specify exactly which outbound emails to encrypt.
Emails that match policy are securely (via TLS) sent to the Barracuda Message Center.
Encryption is configured at the per-domain level, but actual encryption policy (by sender domain, email address, recipient, etc.) is only
configurable at the global level using the BLOCK/ACCEPT pages. These global encryption policies will apply to all domains from which
encrypted email messages are sent.
Figure 1: The sender's email is encrypted by the Barracuda Email Security Service, then stored at the Barracuda Message Center for
retrieval.
Encrypting Messages From the MS Outlook Client
You can download the Barracuda Outlook Add-In for your Microsoft Exchange Server to enable users to choose encryption from the New
Message window in their MS Outlook client. See the Barracuda Spam Firewall Outlook Add-In Deployment Guide 6.0 or the USERS > User
Features page in the Barracuda Spam Firewall web interface for information on deploying the Outlook Add-In. For details about sending and
retrieving encrypted messages as applies to this add-in, see steps 4-6 of Sending and Receiving Encrypted Messages below.
When the Barracuda Spam Firewall encrypts the contents of a message, the message body will not be displayed on the BASIC > Message Log,
BASIC > Outbound Quarantine, or the ADVANCED > Queue Management pages.
Encryption Privacy
Only the sender of the encrypted message(s) and the recipient can view the body of a message encrypted by the Barracuda Email
Encryption Service. For Mail Journaling and the download features in the Message Viewer, the message body will not be sent to the
Mail Journaling account and cannot be downloaded to the Desktop.
If you already have an email encryption server or service, you can specify a hostname (FQDN) or IP address and port in the Redirection Mail
Server TCP/IP Configuration section of the BASIC > IP Configuration page to which the Barracuda Spam Firewall should redirect outbound
mail for encryption. You can then select the Redirect action for outbound filtering policies in the BLOCK/ACCEPT pages. Redirection of outbound
mail per policy is only available at the global (not per-domain) level.
124
To get started enabling and configuring encryption and encryption policies, please see How to Use DLP and Encryption of Outbound Mail.
If you have a Barracuda Message Archiver, you can choose to archive encrypted emails and replies to those emails. From the BASIC >
Administration page, enter the IP address of the Barracuda Message Archiver in the Email Encryption Service section. Note that encrypted
messages are not sent in encrypted format to the Barracuda Message Archiver. It is recommended that this email traffic from the Barracuda
Spam Firewall to the Barracuda Message Archiver be sent over internal networks.
Before applying encryption policy, make sure of the following:
Your Energize Updates subscription is current. See the Subscription Status section on the BASIC > Dashboard page of the Barracuda
Spam Firewall.
You validate all sending domains that are allowed to send encrypted messages, using the DOMAINS > Manage Domain > ADVANCED
> Encryption page. Several validation methods are available from this page.
From the BLOCK/ACCEPT pages you can create global custom encryption policy for secure transmission of outbound mail based on:
Sender email address and/or domain
Recipient email address and/or domain
Attachment Filename pattern and/or type as well as attachment content
Content and content type (such as, for example, secured credit card info.)
These policies will apply for ALL domains from which you send encrypted email.
Branding
You can brand encryption notification emails (see Sending and Receiving Encrypted Messages below) as well as encrypted messages with an
image and a domain name to be displayed with the image. Once you have validated a domain through the Barracuda Spam Firewall, branding is
configured at the per-domain level on the ADVANCED > Encryption page where you can upload an image from your local drive or network. You
can optionally create custom text or html notification message content and subject from the same page.
If an encrypted message is quarantined, the administrator will not see the message contents, but can view the message header information and
the reason the message was encrypted as well as the reason it was quarantined on the BASIC > Message Log page. From either the BASIC >
Message Log page or the BASIC > Outbound Quarantine page, the message can be delivered, rejected, deleted or forwarded.
If an encrypted message is blocked due to policy, the administrator will not see the message contents, but can view the message header
information and the reason the message was encrypted as well as the reason it was blocked on the BASIC > Message Log page. The
administrator can then deliver the message if desired.
For encrypted messages in the queue, the administrator will not see the message contents but can view the message header information and
why the message was encrypted. From the ADVANCED > Queue Management page, the administrator can deliver, re-queue or delete the
message.
The Barracuda Message Center provides a web-based email client for recipients to manage email messages encrypted and sent via the
Barracuda Spam Firewall. The email client looks and behaves much like any web-based email program. See Barracuda Message Center User's
Guide for details on the user experience.
For organizations such as credit card companies, for example, that do not wish recipients to reply to encrypted messages, the Allow Replies opti
on can be set to No on the ADVANCED > Encryption page.
The workflow for email encryption is as follows:
1. The administrator creates a filter from one or more of the BLOCK/ACCEPT pages to encrypt certain types of outbound messages.
2. Outbound messages that meet this filtering criteria are sent over a secure TLS channel to the Barracuda Message Center for encryption.
3. The outbound message information appears in the Barracuda Spam Firewall Message Log, but the message body does not, as it is
encrypted for security purposes.
4. The Barracuda Message Center sends a notification to the recipient of the email message that includes a link the recipient can click to
view and retrieve the message from the Barracuda Message Center. Notifications can be branded as described above.
5. The first time the recipient clicks this link, the Barracuda Message Center will prompt for creation of a password. Thereafter the recipient
125
5.
can re-use that password to pick up subsequent encrypted messages.
6. The recipient logs into the Barracuda Message Center and is presented with a list of email messages, much like any web-based email
program. All encrypted messages received will appear in this list for a finite retention period or until deleted by the recipient.
When the recipient replies to the encrypted email message, the response will also be encrypted and the sender will receive a notification that
includes a link to view and retrieve the message from the Barracuda Message Center.
The Admin or Domain Admin roles can choose to recall an encrypted message before it is read by the recipient. From the BASIC > Message
Log page, clicking on the message brings up the Message Viewer, which includes a Recall button if the message has been encrypted. Clicking
this button recalls the message from the Barrauda Message Center under the following conditions:
The recipient has not yet read the message.
The Remove Barracuda Headers feature is set to No on the ADVANCED > Email Protocol page.
If the message is recalled, the Delivery Status for the message in the log will change to Recalled.
126
How to Use DLP and Encryption of Outbound Mail
enFor health care providers, governmental agencies and other entities who need to protect private, sensitive and valuable information
communicated via email, the Barracuda Spam Firewall includes DLP (Data Leak Prevention) features. DLP enables your organization to satisfy
email compliance filtering for corporate policies and government regulations such as HIPAA and Sarbanes-Oxley. Advanced content scanning is
applied for keywords inside commonly used text attachments, as well as email encryption.You can configure email encryption per domain on the
DOMAINS > Manage Domain > ADVANCED > Encryption page. DLP/Encryption is included with your Energize Updates subscription.
Encryption is configured at the per-domain level, but actual encryption policy (by sender domain, email address, recipient, etc.) is only
configurable at the global level using the BLOCK/ACCEPT pages. These global encryption policies will apply to all domains from which
encrypted email messages are sent.
Encryption is performed by the Barracuda Email Encryption Service, which also provides a web interface, the Barracuda Message Center, for
recipients to retrieve encrypted messages.
Encryption Privacy
When the Barracuda Email Encryption Service encrypts the contents of a message, the message body will not be displayed in the Mes
sage Log. Only the sender of the encrypted message(s) and the recipient can view the body of an encrypted message. For more
information about privacy, please see the Barracuda Networks Privacy Policy
Workflow for Creating, Sending and Receiving Encrypted Messages
Step 1: Configure Encryption for Selected Domains
a. Begin by confirming that you Barracuda Spam Firewall can communicate with the Barracuda Email Encryption Service. If you
are running version 6.0 or higher, from the BASIC > Administration page, enter a valid test email address in the Email
Encryption Service section and use the Test Encryption Connection button. If you are running 5.1.x, navigate to the BASIC >
IP Configuration page and, in the Encryption Service Test section, enter a valid test email address and use the Test
Encryption Connection button.
b. If you are running version 6.0 or higher, and if you have a Barracuda Message Archiver, you can choose to archive encrypted
emails and replies to those emails. From the BASIC > Administration page, enter the IP address of the Barracuda Message
Archiver in the Email Encryption Service section.
c. Make sure that your Energize Updates subscription is current. See the Subscription Status section on the BASIC >
Dashboard page of the Barracuda Spam Firewall.
d. Validate all sending domains that are allowed to send encrypted messages, using the DOMAINS > Manage Domain >
ADVANCED > Encryption page. Several validation methods are available from this page and are detailed in the Help page.
Step 2: Create Policies for DLP/Encryption of Outbound Messages
The administrator creates one or more filters for outbound mail from the BLOCK/ACCEPT pages, selecting Encrypt as the Action. Note that,
though encryption is configured at the per-domain level, actual encryption policy (by sender domain, email address, recipient address, attachment
filename patterns, message content, etc.) is only configurable at the global level. These global encryption policies will apply to all domains from
which encrypted email messages are sent. In addition to criteria mentioned above, you can select the Encrypt action for outbound email
messages that contain matches to pre-made patterns in the subject line, message body or attachment. Use the Predefined Filters on the BLOC
K/ACCEPT > Content Filtering page to configure the following pre-defined data leakage patterns (specific to U.S. - see Note below) to meet
HIPAA and other email security regulations:
Credit Cards - Messages sent through the Barracuda Email Security Service containing recognizable Master Card, Visa, American
Express, Diners Club or Discover card numbers will be subject to the action you choose.
Social Security - Messages sent with valid social security numbers will be subject to the action you choose. U.S. Social Security
Numbers (SSN) must be entered in the format nnn-nn-nnnn.
Privacy - Messages will be subject to the action you choose if they contain two or more of the following data types, using common U.S.
data patterns only: credit cards (including Japanese Credit Bureau), expiration date, date of birth, Social Security number, driver's license
number, street address, or phone number. Phone numbers must be entered in the format nnn-nnn-nnnn or (nnn)nnn-nnnn or nnn.n
nn.nnnn .
HIPAA - Messages will be subject to the action you choose if they contain TWO of the types of items as described in Privacy above and
ONE medical term, or ONE Privacy item, ONE Address and ONE medical term. A street address can take the place of Privacy patterns.
So, for example, a U.S. Social Security Number (SSN), an address, and one medical term is enough to trigger the HIPAA filter.
127
The format of this data varies depending on the country, and these filters are more commonly used in the U.S.; they do not
apply to other locales. Because of the millions of ways that any of the above information can be formatted, a determined person will
likely be able to find a way to defeat the patterns used. These filter options are no match for educating employees about what is and is
not permissible to transmit via unencrypted email.
If you use the Predefined Filters on the BLOCK/ACCEPT > Content Filtering page of the Barracuda Spam Firewall, and you have a problem
with the credit card filter taking action with spreadsheet files that do NOT contain credit card numbers, please see How to Use DLP Filters With
Spreadsheets.
Archiving Encrypted Messages
You can choose to archive all encrypted correspondence for your validated domains on the Barrracuda Spam Firewall to your Barracuda
Message Archiver. Enable this feature by entering the IP address of your Barracuda Message Archiver in the Email Encryption Service section
of the BASIC > Adminstration page of the Barracuda Spam Firewall. For more information, see Archiving Encrypted Email Messages.
Port 4234 should be open for transmission of encrypted mail to the Barracuda Message Archiver.
Step 3: Sending and Receiving Encrypted Messages
The Barracuda Message Center is a web-based email client for receiving and managing encrypted email sent by the Barracuda Email Security
Service or the Barracuda Spam Firewall. The email client looks and behaves much like any web-based email program. For a user's guide, please
see Barracuda Message Center User's Guide. The workflow for sending and receiving encrypted messages is as follows:
1. Outbound messages that meet this filtering criteria and policies configured as described above are encrypted and appear in the Messag
e Log, but the message body does not appear in the log for security purposes.
view and retrieve the message from the Barracuda Message Center.
128
Medical Dictionary Source for DLP HIPAA Compliance
en
The DLP/HIPAA compliance engine is powered by the UMLS Metathesaurus, version 2013AA, created by the U.S. National Library of Medicine,
National Institutes of Health. Within the UMLS Metathesaurus, it uses medical vocabulary from:
COSTAR, by Massachusetts General Hospital, Harvard Medical School
DXplain, by Massachusetts General Hospital, Harvard Medical School
FMA*, by Structural Informatics Group, University of Washington
HCPCS, by Centers for Medicare and Medicaid Services
ICD-9-CM, by U.S. Department of Health and Human Services
MTHICD0, by U.S. National Library of Medicine, National Institutes of Health
NCI Thesaurus, by National Cancer Institute, National Institutes of Health
VANDF, by U.S. Department of Veteran's Affairs
The compliance engine uses only portions of each of the above vocabularies. It also uses vocabulary which is not a part of the UMLS
Metathesaurus, developed by the Barracuda Networks research team.
Some material in the UMLS Metathesaurus is from copyrighted sources of the respective copyright holders. Users of the UMLS Metathesaurus
are solely responsible for compliance with any copyright, patent or trademark restrictions and are referred to the copyright, patent or trademark
notices appearing in the original sources, all of which are hereby incorporated by reference.
*FMA is the intellectual property of the University of Washington and was developed at the University of Washington by the Structural Informatics
Group.
129
How to Use DLP Filters With Spreadsheets
en
If you use Predefined Filters for Data Leakage Prevention (DLP) and have a problem with the credit card filter taking action (false positives) with
spreadsheet files that do NOT contain credit card numbers, this article gives a simple solution. Predefined Filters are configured on the BLOCK
/ACCEPT > Content Filtering page in the Predefined Filters section.
Spreadsheets can store numbers to 16 decimal places which can match a valid Credit Card number check. The Barracuda Spam & Virus Firewall
checks all 16 digit numbers that have a leading period or space and end with a period or space or <CR>, so this number, for example:
254.4012888888881881
...results in checking the number 4012888888881881 against the credit card filter. When tested, this number verifies as a number pattern Visa
supports as a credit card number. This does not mean it is a credit card number currently in use, but that it passes what is known as the Luhn10
test.
If you are sending spreadsheets as attachments, you should set your program to save numbers to 10 or fewer places, or save your document in a
password protected archive so it cannot be scanned by the Barracuda Spam & Virus Firewall for content.
130
Archiving Encrypted Email Messages
en
This feature applies to the Barracuda Spam Firewall running version 6.x and higher.
If you have a Barracuda Message Archiver, you can choose to archive encrypted emails that pass through the Barracuda Spam Firewall, as well
as replies to those emails. From the BASIC > Administration page, enter the IP address of the Barracuda Message Archiver in the Email
Encryption Service section.
Archiving Replies to Encrypted Emails
Any replies to encrypted message go, as usual, to the Barracuda Message Center. The Barracuda Spam Firewall then collects the reply from the
Barracuda Message center and proxies it to the Barracuda Message Archiver. For an illustration of encrypted mail flow (not including the
archiving feature), see the diagram in How to Use DLP and Encryption of Outbound Mail.
Note that encrypted messages are not sent in encrypted format to the Barracuda Message Archiver. Therefore, to protect sensitive mail, it is
recommended that:
This email traffic from the Barracuda Spam Firewall to the Barracuda Message Archiver be sent over internal networks. The Barracuda
Message Archiver will support SMTP/TLS for encrypted transmission of the emails if both the Barracuda Spam Firewall and the
Barracuda Message Archiver are configured to use this protocol:
On the Barracuda Spam Firewall, set Enable SMTP over TLS/SSL to Yes on the ADVANCED > Email Protocol page.
For configuring the Barracuda Message Archiver to receive messages via SMTP over TLS, please contact Barracuda Networks
Technical Support.
You enable the Secondary Authentication feature on the Barracuda Message Archiver from the BASIC > Administration page. Secon
dary Authorization allows an additional password to be required of both Admins and Auditors before executing any action that could
expose message data, including messages that were originally sent encrypted. You can assign the secondary password to a 2nd
administrator, which must be used before the content of these email messages can be viewed. Note that the Secondary Authorization
feature is not limited for use with managing encrypted mail - if you enable it, it will apply to managing all archived mail.
131
Encryption of Outbound Mail 5.x
en
For health care providers, governmental agencies and other entities who need to protect private, sensitive and valuable information
communicated via email, the Barracuda Spam Firewall provides the option of email encryption based on policy you set for outbound mail in the B
LOCK/ACCEPT pages.
Actual encryption of outbound mail is performed by the Barracuda Email Encryption Service, so system performance is never affected. Encryption
is configured at the per-domain level, but actual encryption policy (by sender domain, email address, recipient, etc.) is only configurable at the
global level using the BLOCK/ACCEPT pages. These global encryption policies will apply to all domains from which encrypted email messages
are sent.
Email encryption can be performed by the Barracuda Spam Firewall on outbound mail as described in this article, OR you can download the
Barracuda Outlook Add-In for your Microsoft Exchange Server to enable users to choose encryption from the New Message window in their MS
Outlook client. See Barracuda Spam Firewall Outlook Add-In Deployment Guide 5.x or the USERS > User Features page in the Barracuda
Spam Firewall web interface for information on deploying the Outlook Add-In. For details about sending and retrieving encrypted messages as
applies to this add-in, see steps 4-6 of Sending and Receiving Encrypted Messages.
In this article:
en
Predefined Filters for Data Leakage Prevention (DLP)
Branding
When the Barracuda Spam Firewall encrypts the contents of a message, the message body will not be displayed on the BASIC > Message Log,
BASIC > Outbound Quarantine, or the ADVANCED > Queue Management pages. For Mail Journaling and the download features in the
Message Viewer, the message body will not be sent to the Mail Journaling account and cannot be downloaded to the Desktop.
If you already have an email encryption server or service, you can specify a hostname (FQDN) or IP address and port in the Redirection Mail
Server TCP/IP Configuration section of the BASIC > IP Configuration page to which the Barracuda Spam Firewall should redirect outbound mail
for encryption. You can then select the Redirect action for outbound filtering policies in the BLOCK/ACCEPT pages. Redirection of outbound mail
per policy is only available at the global (not per-domain) level.
Begin by confirming that the Barracuda Spam Firewall can communicate with the Barracuda Email Encryption Service. From the BASIC >
Administration page, enter a valid test email address in the Email Encryption Service section and use the Test Encryption Connection button.
If you have a Barracuda Message Archiver, you can choose to archive encrypted emails and replies to those emails. From the BASIC >
Administration page, enter the IP address of the Barracuda Message Archiver in the Email Encryption Service section .
Before applying encryption policy, make sure of the following:
Your Energize Updates subscription is current. See the Subscription Status section on the BASIC > Dashboard page of the Barracuda
Spam Firewall.
You validate all sending domains that are allowed to send encrypted messages, using the DOMAINS > Manage Domain > ADVANCED
> Encryption page. Several validation methods are available from this page.
From the BLOCK/ACCEPT pages you can select the Encrypt action to create global custom encryption policy for secure transmission of
outbound mail based on:
132
Sender email address and/or domain
Recipient email address and/or domain
Attachment Filename pattern and/or type as well as attachment content
Content and content type (such as, for example, secured credit card info.)
These policies will apply for ALL domains from which you send encrypted email.
Predefined Filters for Data Leakage Prevention (DLP)
DLP enables your organization to satisfy email compliance filtering for corporate policies and government regulations such as HIPAA and
Sarbanes-Oxley. You can select the Encrypt action for outbound email messages that contain matches to pre-made patterns in the subject line,
message body or attachment. Use the following pre-defined data leakage patterns (specific to U.S. – see Note below):
Credit Cards – Messages sent through the Barracuda Email Security Service containing recognizable Master Card, Visa, American
Express, Diners Club or Discover card numbers will be subject to the action you choose.
Social Security – Messages sent with valid social security numbers will be subject to the action you choose. U.S. Social Security
Numbers (SSN) must be entered in the format nnn-nn-nnnn.
Privacy – Messages will be subject to the action you choose if they contain two or more of the following data types, using common U.S.
data patterns only: credit cards (including Japanese Credit Bureau), expiration date, date of birth, Social Security number, driver's license
number, or phone number. Phone numbers must be entered in the format nnn-nnn-nnnn or (nnn)nnn-nnnn or nnn.nnn.nnnn .
HIPAA – Messages will be subject to the action you choose if they contain TWO of the types of items as described in Privacy above and
ONE medical term.
The format of this data varies depending on the country, and these filters are more commonly used in the U.S.; they do not
apply to other locales. Because of the millions of ways that any of the above information can be formatted, a determined person will
likely be able to find a way to defeat the patterns used. These filter options are no match for educating employees about what is and is
not permissible to transmit via unencrypted email.
Branding
You can brand encryption notification emails (see Sending and Receiving Encrypted Messages below) as well as encrypted messages with an
image and a domain name to be displayed with the image. Once you have validated a domain through the Barracuda Spam Firewall, branding is
configured at the per-domain level on the ADVANCED > Encryption page where you can upload an image from your local drive or network. You
can optionally create custom text or html notification message content and subject from the same page.
If an encrypted message is quarantined, the administrator will not see the message contents, but can view the message header information and
the reason the message was encrypted as well as the reason it was quarantined on the BASIC > Message Log page. From either the BASIC >
Message Log page or the BASIC > Outbound Quarantine page, the message can be delivered, rejected, deleted or forwarded.
If an encrypted message is blocked due to policy, the administrator will not see the message contents, but can view the message header
information and the reason the message was encrypted as well as the reason it was blocked on the BASIC > Message Log page. The
administrator can then deliver the message if desired.
For encrypted messages in the queue, the administrator will not see the message contents but can view the message header information and
why the message was encrypted. From the ADVANCED > Queue Management page, the administrator can deliver, re-queue or delete the
message.
The Barracuda Message Center provides a web-based email client for recipients to manage email messages encrypted and sent via the
Barracuda Spam Firewall. The email client looks and behaves much like any web-based email program. See Barracuda Message Center User's
Guide for details on the user experience.
For organizations such as credit card companies, for example, that do not wish recipients to reply to encrypted messages, the Allow Replies opti
on can be set to No on the ADVANCED > Encryption page.
The workflow for email encryption is as follows:
1. The administrator creates a filter from one or more of the BLOCK/ACCEPT pages to encrypt certain types of outbound messages.
2. Outbound messages that meet this filtering criteria are sent over a secure TLS channel to the Barracuda Message Center for encryption.
3. The outbound message information appears in the Barracuda Spam Firewall Message Log, but the message body does not, as it is
encrypted for security purposes.
view and retrieve the message from the Barracuda Message Center. Notifications can be branded as described above.
6.
133
The Admin or Domain Admin roles can choose to recall an encrypted message before it is read by the recipient. From the BASIC > Message
Log page, clicking on the message brings up the Message Viewer, which includes a Recall button if the message has been encrypted. Clicking
this button recalls the message from the Barrauda Message Center under the following conditions:
The recipient has not yet read the message.
The Remove Barracuda Headers feature is set to No on the ADVANCED > Email Protocol page.
If the message is recalled, the Delivery Status for the message in the log will change to Recalled.
134
Securing the Barracuda Spam Firewall
en
In this article:
en
Securing Network Access
SSL Certificates
Secure Links in Notification Emails
Use the Cloud Protection Layer
Limiting Access to the API
Tracking Changes to the Configuration and User Login Activities
Securing User Access With Single Sign-On
User Account Authentication
LDAP and User Account Authentication
Securing Network Access
To secure your Barracuda Spam Firewall on your network, begin by locking down the user interface ports. Barracuda Networks recommends
using the non-standard port 8000 for internal access to the web interface, which is configured on the BASIC > Administration page. From that
page you can also further limit access to the web interface by IP address with the Administrator/IP Range setting. If no IP address is specified in
this field, then all systems are granted access with the correct administrator password.
You can secure external access to the Barracuda Spam Firewall with the Web Interface HTTPS/SSL Port setting on the ADVANCED > Secure
Administration page. The recommended port is 443 because it is a standard HTTPS/SSL port that is used for secure web browser
communication, and the identity of the remotely connected server can be verified with significant confidence. To configure SSL-only access to the
web interface, see How to Enable SSL for Administrators and Users.
If per-user quarantine is enabled as well as HTTPS, users will be redirected to HTTPS access if they are trying to access their
quarantine inbox.
SSL Certificates
As described above, limiting user interface access to HTTPS provides further security and can also be configured on the ADVANCED > Secure
Administration page along with the use of SSL certificates. There are three types of SSL certificates to choose from:
Default (Barracuda Networks)
Private (self-signed)
Trusted certificate - a certificate signed by a trusted certificate authority (CA)
Configuring SSL certificates is described in this guide in the How to Enable SSL for Administrators and Users as well as in the online help of the
ADVANCED > Secure Administration page.
Secure Links in Notification Emails
If Per-User quarantine (as opposed to Global) is configured on the BASIC > Quarantine page, you might want to secure hyperlinks in
quarantine correspondence emails that are sent from the Barracuda Spam Firewall to users and administrators. Setting Use HTTPS Links in
Emails to Yes on the ADVANCED > Secure Administration page ensures that these emails sent from the Barracuda Spam Firewall contain
only HTTPS links.
Use the Cloud Protection Layer
Using the Cloud Protection Layer feature means that all email going into your organization will be pre-filtered for spam and viruses before it
reaches your network. This feature requires using the Barracuda Control Center and validating your domain ownership with the cloud service. To
use this feature, please see Cloud-Based Protection for details on configuration.
Limiting Access to the API
The Barracuda set of APIs provides for remote administration and configuration of the Barracuda Spam Firewall. More detailed information
regarding the API can be found in the Barracuda Spam Firewall API Guide. Common settings, such as IP addresses and spam scoring levels,
that you can set by clicking the Save Changes button in the web interface, can be configured via the API.
To limit access to the API, use the Allowed SNMP and API IP/Range setting on the BASIC > Administration page. The IP addresses you enter
in that field can also establish an SNMP connection to the system.To secure use of the API, you must also create an API password which can be
entered on the same page.
135
Tracking Changes to the Configuration and User Login Activities
The syslog function of the Barracuda Spam Firewall provides two kinds of logs, capturing:
User login activities and any configuration changes made on the device.
Data related to mail flow. This data is the same information as that used to build the Message Log in the Barracuda Spam Firewall.
From the ADVANCED > Troubleshooting page, use the Monitor Web Syslog button view the web syslog output. You can also configure a
syslog server as described in Using a Syslog Server to Centrally Monitor System Logs.
Securing User Access With Single Sign-On
Single Sign-On is a per-domain setting available on the Barracuda Spam Firewall 400 and higher.
With Single Sign-On (SSO), users can log into their quarantine inbox via the web interface using their domain passwords instead of a password
managed separately by the Barracuda Spam Firewall. Single Sign-On is configured at the domain level by either the Administrator or a Domain
Admin. See Roles and Navigating the Web Interface for more detail about how roles work.
Note that, if you are using LDAP authentication for single sign-on, you can either use the same LDAP server and settings for user authentication
as the one you’re using for recipient verification (configured on the USERS > LDAP Configuration page), or you can configure a separate LDAP
server for single sign-on from the USERS > Single Sign-On page. Please see the help on that page for specifics about LDAP server settings to
understand how they affect user logins and access to their quarantine inbox.
Important
If enabling Single Sign-On for a domain, you should also configure HTTPS/SSL Access Only at the global level on the ADVANCED >
Secure Administration page to protect the transmission of network passwords. See How to Enable SSL for Administrators and Users
to configure SSL access only to the web interface of the Barracuda Spam Firewall.
User Account Authentication
You can configure the Barracuda Spam Firewall to authenticate user accounts using an LDAP, POP, or RADIUS server. This feature is available
on the Barracuda Spam Firewall 400 and higher and is configured at the domain level, not as a global setting. These user account authentication
mechanisms are configured from the DOMAINS tab by selecting the Domains page and clicking the Manage Domain link for a particular domain.
To configure authentication, navigate to the USERS > Single Sign-On page for the selected domain and select the Authentication Type. For
RADIUS and POP, fill in the server settings on the page. To require users to log in to the Barracuda Spam Firewall Web interface (as opposed to
single sign on) to view and manage their account, select Local for Authentication Type.
LDAP and User Account Authentication
Configure LDAP settings on the USERS > LDAP Configuration page. LDAP server types supported include Active Directory, Open LDAP,
Novell eDirectory and Domino Directory. You can configure LDAPS (SSL/TLS) for encryption of LDAP queries between the Barracuda Spam
Firewall and your LDAP server. LDAPS can optionally be required. As stated above, these settings are domain-specific.
If you select LDAP authentication, you can configure the Exchange Accelerator/LDAP Verification feature on the USERS > LDAP
Configuration page as follows:
Setting to Yes means that LDAP lookups for recipient verification for the domain will be performed based on settings on the page.
Setting to No means that the Barracuda Spam Firewall will default to SMTP verification through RCPT TO commands.
See also: Roles and Navigating the Web Interface
136
Cloud-Based Protection
en
The optional Cloud Protection Layer (CPL) feature of the Barracuda Spam Firewall is an additional layer of protection that blocks threats before
they reach your network and provides email continuity. Once email passes through the CPL, the Barracuda Spam Firewall filters email according
to the more granular policies, recipient verification, quarantining and other features you configure on the appliance. You’ll use Barracuda Cloud
Control for central management of your CPL and your Barracuda Spam Firewall(s). See How to Set Up Barracuda Cloud Control for details.
To configure your CPL, see How to Set Up Your Cloud Protection Layer (CPL).
Advantages of using Cloud-Based Protection
The CPL provides yet another layer of security by pre-filtering inbound email for spam and viruses in the cloud before it reaches your actual
network. Here are some of the great benefits of enabling this feature:
Email Continuity – The CPL polls your inbound mail server regularly and, if the mail server goes down, the CPL spools your inbound mail
for up to 4 days. As soon as the mail server comes back up, email is released in a steady stream, resuming consistent inbound mail flow.
Dual Protection Points – comprehensive onsite and cloud-based threat protection including the Barracuda Anti-Virus Super Computing
Grid and Barracuda Advanced Anti-Fraud Intelligence.
Email Burst Handling – email surge suppression during peak traffic and spam spikes, which offloads a significant volume of spam email
to be filtered via the cloud.
Immediate Response – automatic updates in real-time leveraging threat intelligence from Barracuda Labs and Barracuda Central to
continuously stay ahead of quickly morphing threats.
Note that the CPL can be configured with many of the same block/accept policies you would apply to the Barracuda Spam Firewall, but only
provides the Block and Allow actions. The CPL does not support tagging or quarantine of email.
137
How to Set Up Your Cloud Protection Layer (CPL)
en
To use the Cloud Protection Layer (CPL), you must have a current Energize Updates (EU) subscription for your Barracuda Spam
Firewall.
In this article:
en
Create or Log Into Your Barracuda Cloud Control Account
Configure Cloud Control
Configuring Cloud Protection Layer Spam Settings
Viewing Email Statistics
Monitor Incoming Emails
Integration With the Barracuda Spam Firewall
Create or Log Into Your Barracuda Cloud Control Account
Begin setup of your CPL by either creating a Barracuda Cloud Control account or logging in with your existing account. If already have an
account, skip to Configure Cloud Control below.
To create a Barracuda Cloud Control account:
1. Visit https://login.barracudanetworks.com/ and click the Create a user link.
2. Enter your name and email address, and click Create User. Follow the instructions emailed to the entered email account to log in and
create your Barracuda Cloud Control account.
3. After submitting your new account information, the Account page displays your account name, associated privileges, username, and
Barracuda Networks products you associate with your Barracuda Cloud Control account.
Configure Cloud Control
1. Log into your account at https://login.barracudanetworks.com/ and enter your email address and password.
2. Click Sign In. Once logged in you can create users in your Barracuda Cloud Control account (see How to Add Users) and assign various
permissions to each user for access to Barracuda Cloud Control.
3. Click on the Appliance Control link on the left side of the page. If you have not yet connected any appliances or services to your
account, click the Set up your Barracuda Cloud Control button. You’ll see the Barracuda Cloud Control Dashboard page and a
message indicating that no products have yet been connected.
4. In another browser tab or window, log into your Barracuda Spam Firewall. From the product ADVANCED > Firmware Upgrade page,
check to make sure you have the latest firmware installed. If not, download and install it now.
5. From the ADVANCED > Cloud Control page, enter the username and password you created for your Barracuda Cloud Control account.
Click Yes for Connect to Barracuda Cloud Control to connect your Barracuda Spam Firewall to the Barracuda Cloud Control, and then
click the Save Changes button. Note that your Barracuda Spam Firewall can connect with only one Barracuda Cloud Control account at
a time.
6. In the Barracuda Cloud Control window, refresh your browser page. You should see, in the Products column in the left side of the page,
the Spam Firewall group with two components, or ‘nodes’ listed:
The Cloud Protection Layer node
Each Barracuda Spam Firewall you have connected, with its serial number
7. Click on the Cloud Protection Layer link and navigate to the DOMAINS > Domains page.
Important
The MX record for each domain should point to the Barracuda Spam Firewall so that the CPL can establish a connection to the
system.
For each domain for which you want the CPL to filter email, do the following:
a. For each domain you have configured on the Barracuda Spam Firewall, click the Add Destination link in the table.
b. In the Destination Server field, enter the external facing (public) IP address of your Barracuda Spam Firewall. This is typically,
but not always, the IP Address from the BASIC > IP Configuration page. The CPL must be able to establish and confirm a
connection to the Barracuda Spam Firewall in order to receive the required MX records.
138
Important: If your Barracuda Spam Firewall is behind a relay or mail proxy, the CPL may not be able to validate your
domains.
c. Add the port of the destination server in the Destination Port field, and set a priority for that mail server in the Destination
Priority field. Click Add, and repeat each domain. To list multiple destination servers for the domain, repeat steps a. - c., adding
a different destination server, and assigning that server a priority value. The domain will then be displayed with the destination
servers associated with it.
After the destination servers are entered, click the Verify link.
d. The CPL will verify domain ownership, and, if the CPL can communicate with the Barracuda Spam Firewall, the Status of the
domain in the table will change from Not Verified to Verified, and you will see 2 MX records in the Manage Domains table for
that domain. If ownership of the domain cannot be verified, the CPL will not receive email for that domain.
8. Finally, add the MX records in the Manage Domains table for each domain to your external DNS through your ISP or domain hosting
provider. Once the DNS entries have propagated, the CPL will begin receiving mail immediately.
Configuring Cloud Protection Layer Spam Settings
Important: Initially, the configuration on your Barracuda Spam Firewall will automatically be copied to your CPL so you don’t have to
re-configure policy for your existing domains. You can then edit policies in the CPL if needed.
You can configure most of the same filtering policies and SMTP settings in the CPL web interface that you can on your Barracuda Spam Firewall
using the BASIC, BLOCK/ACCEPT and ADVANCED > Email Protocol pages. For greatest security, it is highly recommended that you enable
virus scanning and Barracuda Real-Time Protection on the BASIC > Virus Scanning page in the CPL.
Viewing Email Statistics
When you click on the top level of the Barracuda Cloud Control products list, you will see statistics for ALL of your products, including the CPL for
your Barracuda Spam Firewall. However, when you click on the Barracuda Spam Firewall group in the same pane, you’ll see statistics for all
inbound mail through both the CPL and all inbound and outbound mail for the Barracuda Spam Firewall.
To see how many messages were blocked by the CPL, click on that link under the Cloud Protection Layer in the Products list and navigate to
the BASIC > Dashboard page. This page shows you ONLY statistics for inbound traffic through the CPL. Use these traffic profiles along with the
Message Log to determine how to best tune your spam policies.
To see how many messages were blocked by one or more of your Barracuda Spam Firewalls, expand the All Spam Firewalls link and click on the
system you want to view, then navigate to the BASIC > Dashboard page.
Monitor Incoming Emails
Once email is flowing through the CPL, the administrator can view the BASIC > Message Log page of the service to get an idea of how many
messages are being blocked by the CPL, with reasons for each of those actions. Reviewing the log will give an idea of how current CPL (as well
as Barracuda Spam Firewall) settings are filtering messages.
Integration With the Barracuda Spam Firewall
The CPL Message Log fully integrates inbound email activity processed by the CPL with inbound email activity processed by the Barracuda
Spam Firewall. The Action and Reason columns in the CPL Message Log are the key to seeing how the CPL blocks spam and virus threats
139
before they reach your network. For blocked messages, the Reason column in the log indicates whether the message was blocked by the CPL or
the Barracuda Spam Firewall. For messages blocked by the CPL, the Reason value will be appended by [Cloud Protection Layer]. For the
Barracuda Spam Firewall, the Reason value will be appended by [BAR-SF-123456], where ‘123456’ represents the serial number.
Remember that only the Barracuda Spam Firewall tags or quarantine messages. Messages that are Allowed passed through filters in both the
CPL and the Barracuda Spam Firewall.
140
Advanced Spam Filtering Inbound
en
The goal in configuring a Barracuda Spam Firewall is to identify spam without blocking valid messages. These articles address using custom
spam filtering policy on inbound mail as well as optional, more sophisticated spam identification methods. For information about Spam scoring for
inbound mail, see How Spam Scoring Works.
In this Section
Rate Control Inbound
IP Analysis Inbound
Content Analysis Inbound
Bayesian Analysis Inbound
141
Rate Control Inbound
en
The Barracuda Spam Firewall Rate Control feature protects the system from spammers or spam-programs (also known as "spam-bots") that
send large amounts of email to the server in a small amount of time. Rate Control is configured on the BLOCK/ACCEPT > Rate Control page.
As part of the Connection Management Layer, the Rate Control mechanism counts the number of connections to the Barracuda Spam Firewall in
a half hour period and compares that number to the Rate Control threshold, which is the maximum number of connections allowed from any one
IP address in this half-hour time frame. If the number of connections from a single IP address exceeds the Rate Control threshold within the half
hour period, the Barracuda Spam Firewall will defer any further connection attempts from that particular IP address until the next half hour time
frame and log each attempt as deferred in the Message Log with a Reason of Rate Control.
In this case, for each message deferred, the sender will receive a 4xx level error message instructing the mail server to retry after a predefined
time interval. Well-behaving mail servers act upon the defer message and will try sending the message again later, while email from large volume
spammers will not retry sending the email again.
When Rate Control Takes Effect
When Rate Control is first enabled on the Barracuda Spam Firewall, or after a change is made to the Rate Control threshold, five (5) unique IP
addresses must connect before Rate Control is invoked. This is to take into account that you may have another appliance receiving email (i.e., a
front-end Mail Transfer Agent (MTA) or a trusted forwarder) before the Barracuda Spam Firewall. Once 5 or more IP addresses have made
connections to the Barracuda Spam Firewall, it indicates that mail is also coming in from other outside sources and rate control should be applied.
Exemptions from Rate Control
You can exempt trusted IP addresses from Rate Control by adding a trusted IP address to the Rate Control Exemption/IP range list. Also, any
IP address that you enter as a trusted forwarder on the BASIC > IP Configuration page will be exempted from Rate Control.
When configuring Rate Control, keep in mind the following
A rate of 50 is conservative
Some customers can lower this safely
Caution – False positives can be hard to diagnose
Common setting is for 20-30 emails/ half hour
High volume recipients may need to either set the Rate Control Threshold above 50 and/or list IP addresses from which they expect to
receive a high volume of email in the Rate Control Exemption/IP Range list.
Organizations that relay email through known servers or communicate frequently with known partners can and should add the IP
addresses of those trusted relays and good mail servers to the Rate Control Exemption/IP Range list.
142
IP Analysis Inbound
en
In this article:
en
About IP Analysis
Trusted Forwarders
IP Reputation
Barracuda Reputation (BRBL)
Exempting IP Addresses from the BRBL and Other Blocklists
Subscribing to External Blocklist Services
Sender Whitelisting - Precedence
Reverse DNS Blocking
About IP Analysis
After applying rate controls, the Barracuda Spam Firewall then performs analysis on the IP address, applying tag, quarantine or block policies that
you configure in the BLOCK/ACCEPT pages.
Once the true sender of an email message is identified, the reputation and intent of that sender should be determined before accepting the
message as valid, or "not spam". The best way to address both issues is to know the IP addresses of trusted senders and forwarders of email
and define those on the Barracuda Spam Firewall as "Allowed" by adding them to a whitelist of known good senders. Various methods for
discerning "good" senders of email versus spammers are described in this section to help you to quickly configure your Barracuda Spam Firewall
per the needs of your organization.
Barracuda Networks does NOT recommend whitelisting domains because spammers will spoof domain names. When possible, it is
recommended to whitelist (Allow) by IP address only.
Trusted Forwarders
On the BASIC > IP Configuration page you can specify the IP addresses of any machines that are set up specifically to forward mail to the
Barracuda Spam Firewall from outside sources. These are called Trusted Forwarders and will bypass SPF, Rate Control and IP Reputation
checks. In the IP Analysis layer, the Barracuda Spam Firewall examines the Received headers and evaluates the first non-trusted IP address
when applying the above filters and other block and accept policies.
IP Reputation
The Barracuda Spam Firewall enables administrators to define a list of trusted mail servers by IP address. By adding IP addresses to this list,
administrators can avoid spam scanning of good email, thereby both reducing processing load and eliminating the chances of false positives.
Note that virus scanning and blocked attachment checks are still enforced.
Likewise you can define a list of bad email senders. In some cases, you may choose to utilize IP blocklists on the BLOCK/ACCEPT > IP Filters p
age to restrict specific mail servers as a matter of policy rather than as a matter of spam.
Barracuda Reputation (BRBL)
Barracuda Reputation is a database maintained by Barracuda Central and includes a list of IP addresses of known, good senders as well as
known spammers, or IP addresses with a "poor" reputation. This data is collected from spam traps and other systems throughout the Internet.
The sending histories associated with the IP addresses of all sending mail servers are analyzed to determine the likelihood of legitimate
messages arriving from those addresses. Updates to Barracuda Reputation are made continuously by the engineers at Barracuda Central and
are delivered to all Barracuda Spam Firewalls via Energize Updates.
On the BLOCK/ACCEPT > IP Reputation page, it is strongly recommended that the Barracuda Reputation Blocklist (BRBL) option be set to
"Block".
(Available in version 6.1 and higher) This feature replaces the Barracuda Reputation Whitelist feature in version 6.1 and higher. Email
Categorization gives administrators more control over what they believe to be spam, even though those messages may not meet the technical
definition of spam. Most users do not realize that newsletters and other subscription-based emails, while they are considered to be bulk email, are
not technically unsolicited - which means that they can not be blocked by default as spam. The senders of these emails may have a good
reputation, but the user may no longer want to receive, for example, a mass mailing from a club or vendor membership. The Email Categorization
feature assigns these kinds of emails to categories that display on the BLOCK/ACCEPT > IP Reputation page, and the administrator can then
create Block, Quarantine, Tag or Whitelist (allow) policies by category. Or the action can be Off, in which messages are not scanned for Email
Categorization. If the message action is Tag, the message subject will indicate the category name. Categories supported are:
143
Transactional Emails - Emails related to order confirmation, bills, bank statements, invoices, monthly bills, UPS shipping notices,
surveys relating to services rendered and or where transactions took place. The default action is Whitelist (allow).
Barracuda recommends setting Whitelist for the Transactional Emails category to prevent overlooking potentially important billing,
bank statements and other time sensitive information.
Corporate Emails - Email sent from MS Exchange Server that involves general corporate communications. Does not include marketing
newsletters. The default action is Whitelist (allow).
Marketing Materials and Newsletters - Promotional emails from companies such as Constant Contact. The default action is Off (no
action taken).
Other - On the Message Log page, the administrator has the opportunity to assign selected messages in the log to a custom category
that is 'written in' when clicking the Categorize button in the log. See the BASIC > Message Log page for details.
Exempting IP Addresses from the BRBL and Other Blocklists
The BRBL and other blocklists that you specify on the BLOCK/ACCEPT > IP Reputation page can be overridden by listing the IP addresses or
email addresses:
In the Barracuda Reputation, External RBL IP Exemption Range section of the BLOCK/ACCEPT > IP Reputation page. Here, you
can exempt particular IP addresses from RBL checks, including from the Barracuda Reputation Blocklist. Messages from these IP
addresses will be subject to all other spam and virus checks.
In the Allowed IP/Range section or Blocked IP/Range section of the BLOCK/ACCEPT > IP Filters page.
In the Allowed Email Addresses and Domains section or Blocked Email Addresses and Domains section of the BLOCK/ACCEPT >
Sender Filters or BLOCK/ACCEPT > Recipients pages.
Subscribing to External Blocklist Services
The BLOCK/ACCEPT > IP Reputation page allows you to use various blocklist services. Several organizations maintain external blocklists, such
as spamhaus.org. External blocklists, sometimes called DNSBLs or RBLs, are lists of IP addresses from which potential spam originates. In
conjunction with Barracuda Reputation, the Barracuda Spam Firewall uses these lists to verify the authenticity of the messages you receive.
Be aware that blocklists can generate false-positives (legitimate messages that are blocked). However, because the Barracuda Spam Firewall
sends notifications when it rejects such messages, the sender will be notified and legitimate senders will therefore know to try re-sending their
message or otherwise notify the recipient that their messages are being blocked.
Subscribing to blocklist services does not hinder the performance of the Barracuda Spam Firewall. Query response time is typically in
milliseconds, so delays are negligible. Once the Barracuda Spam Firewall queries a blocklist service, that query is cached on your own local DNS
for a period of time, making further queries very fast.
Sender Whitelisting - Precedence
The users' sender whitelists (if the whitelist/blocklist setting is enabled for user accounts) can be overridden by global settings. For example, if the
administrator turns on Spoof Protection, which is a global setting, it will supersede any user’s whitelist entry. If a user needs to supercede an
global IP address block, that user should communicate to the administrator and request that the email or IP address be added to a global whitelist
on the Barracuda Spam Firewall.
The Barracuda Spam Firewall can do a reverse DNS lookup on inbound and outbound IP connections and finds the hostname associated with
the IP address of the sender. By configuring rules on the BLOCK/ACCEPT > Reverse DNS page, you can choose to apply Common Reverse
DNS Rules by country, Custom Reverse DNS Rules that you define, or both to block, quarantine, tag (inbound only) or whitelist (Custom
Reverse DNS Rules only).
The last part of a hostname is known as the top level domain, or TLD. Most TLDs include a country identifier, such as .ca for Canada, .ru for
Russia, etc. If most or all of the mail that you receive from a particular country is spam, you can use the Common Reverse DNS Rules to tag
(inbound only), block or quarantine any any message that has an associated hostname that includes that country's TLD. Email which is not
blocked is subject to all of the usual spam and virus checks. Use the Custom Reverse DNS Rules to tag, quarantine or block messages from
hostnames ending with values that you specify. List the sending domains or subdomains you want to whitelist on the BLOCK/ACCEPT > Sender
Filters page.
144
Content Analysis Inbound
en
In this article:
en
Custom Content Filters
Blocking Email by Country
Intent Analysis
Image Analysis
The Barracuda Spam Firewall enables administrators to set custom content filters based on the subject line, message headers, message body
and attachment file content. In general, administrators do not need to set their own filters for the purposes of blocking spam, as these forms of
rules are delivered to the Barracuda Spam Firewall automatically through Barracuda Energize Updates. The online help for the BLOCK/ACCEPT
> Content Filtering page includes a link to a Regular Expressions help page that covers expressions you can use for advanced filtering. HTML
comments and tags imbedded between characters in the HTML source of a message are also filtered.
You can specify actions to take with messages based on pre-made patterns in the subject line or message body. Credit card, Social Security
numbers, privacy information such as driver’s license numbers, phone numbers or expiration dates and HIPAA data can be automatically
checked and acted upon by blocking, tagging or quarantining inbound messages.
All messages, except those from whitelisted senders, go through attachment filtering. From the BLOCK/ACCEPT > Attachment Filters page
you can choose to take certain actions with inbound and/or outbound messages if they contain attachments with certain filename patterns, file
types, MIME types, or password protected archives. Actions you can take with inbound messages include block or quarantine. Actions you can
take with outbound messages include block, quarantine, encrypt or redirect. You can elect to have a notification sent to the sender when an
inbound or outbound message is blocked due to attachment content filtering. See the ADVANCED > Bounce/NDR Settings page to configure
notifications.
The BLOCK/ACCEPT > Attachment Filters page provides a table of patterns you can use for specifying the above actions based on attachment
filenames, or you can create your own filters.
The Check Archives feature can be selected along with any filter to search the contents of attached archives (zip, tar, etc.) and take one of the
above actions with inbound or outbound messages based on filenames or types.
Use the Password Protected Archive Filtering feature to take action with messages with attachments that contain password protected
(encrypted) archives.
Messages that are blocked due to attachment filtering will appear in the Message Log with the word Attachment and the filename in the Reason
column. For example, if you created a filter on the BLOCK/ACCEPT > Attachment Filters page to block messages with attachments whose
filenames match a pattern of word*, the entry in the Message Log for such a blocked message would contain something like this in the Reason
column:
Attachment (word_2010_xml.tgz)
where word_2010_xml.tgz is the attachment filename that caused the message to be blocked.
The default maximum attachment size allowed by your Barracuda Spam Firewall is 100 megabytes. If a message exceeds this
size, the Barracuda Spam Firewall rejects the message and the sending server notifies the sender that their message did not go
through. Contact Barracuda Networks Technical Support to change this maximum.
Blocking Email by Country
Set tag, quarantine and block policies for specific character sets or regional spam settings using the BLOCK/ACCEPT > Regional Settings page
. Here you can also choose to specifically allow messages based on valid Chinese or Japanese language content and enable compliance with
PRC (People’s Republic of China) requirements if your Barracuda Spam Firewall resides in the PRC.
A message "fingerprint" is based on commonly used message components (e.g., an image) across many instances of spam. Fingerprint analysis
is often as a useful mechanism to block future instances of spam once an early outbreak is identified. Spam fingerprints blocked based on a
real-time check will display an '*' before "Fingerprint" in the Message Log. In order to detect real-time spam fingerprints, Barracuda Real-Time
Protection must be enabled on the BASIC > Virus Checking page.
145
Engineers at Barracuda Central work around the clock to identify new spam fingerprints which are then updated on all Barracuda Spam Firewalls
through hourly Barracuda Energize Updates. Fingerprint Analysis is configured on the BASIC > Spam Checking page.
Intent Analysis
All spam messages have an "intent" to get a user to reply to an email, visit a web site or call a phone number. Intent analysis involves
researching email addresses, web links and phone numbers embedded in email messages to determine whether they are associated with
legitimate entities. Frequently, Intent Analysis is the defense layer that catches phishing attacks. The Barracuda Spam Firewall features multiple
forms of Intent Analysis:
Intent analysis – Markers of intent, such as URLs, are extracted and compared against a database maintained by Barracuda Central,
and then delivered to the Barracuda Spam Firewall via hourly Barracuda Energize Updates. Intent can also be associated with general
content categories, several of which are provided for Intent filtering.
Real-time intent analysis – For new domain names that may come into use, Real-Time Intent Analysis involves performing DNS
lookups against known URL blocklists.
Multilevel intent analysis – Use of free web sites to redirect to known spammer web sites is a growing practice used by spammers to
hide or obfuscate their identity from mail scanning techniques such as Intent Analysis. Multilevel Intent Analysis involves inspecting the
results of web queries to URLs of well-known free web sites for redirections to known spammer sites.
Intent Analysis is configured on the BASIC > Spam Checking page.
Image Analysis
Image spam represents about one third of all traffic on the Internet. While Fingerprint Analysis captures a significant percentage of images after
they have been seen, the Barracuda Spam Firewall also uses Image Analysis techniques which protect against new image variants. These
techniques include:
Optical character recognition (OCR) – Embedding text in images is a popular spamming practice to avoid text processing in anti-spam
engines. OCR enables the Barracuda Spam Firewall to analyze the text rendered inside the images.
Image processing – To mitigate attempts by spammers to foil OCR through speckling, shading or color manipulation, the Barracuda
Spam Firewall also utilizes a number of lightweight image processing technologies to normalize the images prior to the OCR phase.
More heavyweight image processing algorithms are utilized at Barracuda Central to quickly generate fingerprints that can be used by
Barracuda Spam Firewalls to block messages.
Animated GIF analysis – The Barracuda Spam Firewall contains specialized algorithms for analyzing animated GIFs for suspect
content.
Image Analysis is configured on the BASIC > Spam Checking page.
146
Bayesian Analysis Inbound
en
In this article:
en
How Bayesian Analysis Works
Global Bayesian Filtering Versus Per-User
Getting the Best Accuracy From the Bayesian Database
When to Use Bayesian Analysis
Bayesian Poisoning
How Bayesian Analysis Works
Bayesian Analysis is a linguistic algorithm that profiles language used in both spam messages and legitimate email for any particular user or
organization. To determine the likelihood that a new email is spam, Bayesian Analysis compares the words and phrases used in the new email
against the corpus of previously identified email. Note that Bayesian training works only on messages with 11 words or more. The Barracuda
Spam Firewall only uses Bayesian Analysis after administrators or users classify at least 200 legitimate messages and 200 spam messages.
Global Bayesian Filtering Versus Per-User
The administrator can configure a global Bayesian database, per-user Bayesian databases or disable Bayesian altogether. With the global
setting, which is configured on the BASIC > Spam Checking page, the administrator trains and maintains one Bayesian database for all users.
With the per-user configuration, users must train and manage their own Bayesian databases, which they access from their PREFERENCES >
Spam Checking page. There are pros and cons to each configuration.
A global Bayesian database is typically more effective than per-user databases because the administrator can maintain and reset it for all to use,
thereby providing a more reliable source of Bayesian management. If, however, the Barracuda Spam Firewall is filtering mail for many domains,
the users of which expect to receive different types of email, it could be either difficult or impossible to train the global Bayesian database to
identify spam for all users. For example, if one domain for a medical organization typically receives email regarding medical topics, while another
domain for a political organization tends to receive political emails and yet another domain is an entertainment site, then what is spam to one
domain may be valid email for another on the same Barracuda Spam Firewall. In this case, per-user Bayesian filtering would make more sense
than global.
In most cases, however, it is not practical to enable Bayesian at the user level because maintaining an accurate Bayesian database requires that
users to understand the concept of how Bayesian analysis works and how to use it as an effective tool. That said, while sophisticated users may
be trained and savvy enough to initially train their own Bayesian database, they may not have the time to spend in their regular work schedule to
effectively maintain their Bayesian databases.
Because spammers frequently change tactics and content, Bayesian data can quickly become "stale" if the database is not reset from
time to time and new messages consistently classified as spam or not spam in equal numbers. Without this maintenance the users may
see false positives resulting in the blocking of good email.
Getting the Best Accuracy From the Bayesian Database
All Bayesian systems rely on the fact that messages classified are not much different than new messages arriving. Over time however, spam
messages change drastically and the Bayesian system – while initially able to compensate for the new format – gradually declines in its
effectiveness. When this happens new classifications are needed to update the Bayesian database. To keep a Bayesian database accurate:
For a global Bayesian database, the administrator should periodically (every 6 months or so) clear it out by resetting it from the BASIC >
Spam Checking page, then, from the BASIC > Message Log page, marking at least 200 messages as either Spam or Not spam using
the buttons on the page. Bayesian filtering will NOT take effect until 200 or more of each spam and not-spam messages are marked as
such.
For each per-user database, the user should reset their own Bayesian database and follow up with marking 200 or more messages as
spam or not spam, either in their quarantine inbox (QUARANTINE > Quarantine Inbox page) or from their regular email client if they
have installed the Barracuda Outlook add-in (see below).
When to Use Bayesian Analysis
Barracuda Networks does not recommend using Bayesian filtering in most circumstances. With Energize Updates constantly updating the
Barracuda Spam Firewall with protection against the latest spam and virus threats, spam accuracy should not be an issue for most organizations.
A case for using Bayesian Analysis would depend on the following:
You are using global Bayesian as opposed to per-user, and the users in the organization tend to be a homogenous population with
regard to the kind of content considered to be ‘valid’ email versus spam. This situation would make it easier for an administrator to "train"
147
the global Bayesian database as to what is spam and what is not spam for the organization.
Your organization requires a very high granularity of accuracy for identifying spam.
If enabling Bayesian at the per-user level, users are sophisticated and can be trained to properly identify ‘valid’ messages versus spam
so as to train the Bayesian database, and are willing to consistently mark BOTH ‘valid’ messages and spam messages in equal numbers
so as to maintain the Bayesian database.
The administrator and/or users are disciplined about resetting the Bayesian database(s) on a regular basis and re-initializing with 200
each of marked spam and not spam messages to ‘keep current’ with new spam techniques over time.
If both per-user quarantine and per-user Bayesian are enabled, on the Barracuda Spam Firewall 300 and higher, the administrator can choose to
allow users to download an add-in that allows messages to be classified as Spam or Not Spam directly from their email client. Users must have a
quarantine account on the Barracuda Spam Firewall to use the add-in. For information about automatically or manually creating quarantine
accounts for users, see Creating and Managing Accounts. For more information about the Barracuda Outlook Add-in, see the Barracuda Spam
Firewall Outlook Add-In Deployment Guide.
Bayesian Poisoning
Some spammers will insert content in messages intended to bypass spam rules, such as excerpts of text from books or other content that may
look "legitimate" in order to fool spam filtering algorithms. This tactic is called Bayesian Poisoning and could reduce the effectiveness of a
Bayesian database if many of these messages are marked as either spam or not spam. The Barracuda Networks Bayesian engine is, however,
very sophisticated and protects against Bayesian Poisoning if administrators or users consistently maintain their databases.
148
Advanced Spam Filtering Outbound
en
Outbound mail shares some of the same block / accept mechanisms available for inbound mail, with a few differences, which are described here.
Additionally, outbound messages can be encrypted based on filtering criteria you configure on the BLOCK/ACCEPT pages.
In this Section
Spam Scoring Outbound
Rate Control Outbound
IP Analysis Outbound
Sender and Recipient Filtering Outbound
Content Analysis Outbound
Attachment Filtering Outbound
Bayesian Analysis Outbound
149
Spam Scoring Outbound
en
The last filtering event applied to an outbound email message is assignment of a score based on the probability that it is spam. The administrator
can decide how to deal with outbound messages suspected be spam based on the Outbound Spam Scoring Limits as configured on the BASI
C > Spam Checking page. For more information, see How Spam Scoring Works.
Spam scoring limits (from 0 to 9.9) can determine whether to send, quarantine or block outbound messages:
Quarantining the message means that the message is suspected to be spam or in violation of policy, and will be stored on the Barracuda
Spam Firewall for the administrator to review. The message can then be whitelisted, rejected, deleted or delivered by the administrator.
See Managing Outbound Quarantine for more information.
Blocking the message means it will not be delivered. If a message is blocked due to its spam score, and if the Send Bounce option for
Outbound is set to Yes in the Spam Bounce (NDR) Configuration section of the ADVANCED > Bounce/NDR Settings page, a
non-delivery receipt (NDR/bounce message) is also sent to the sender by the Barracuda Spam Firewall.
Note that, unlike with inbound mail, the Barracuda Spam Firewall does not offer tagging of outbound messages.
150
Rate Control Outbound
en
Outbound mail is rate controlled based on IP address by the Barracuda Spam Firewall as described in Rate Control Inbound. Rate Control for
outbound email, however, can also be applied based on sender email address. If the number of recipients from a sender email address exceeds
the specified Maximum Recipients per Sender over a 30 minute time period, the Barracuda Spam Firewall will defer any further connection
attempts from that particular sender until the next time frame. Deferred outbound messages will be logged as Rate Controlled in the Message
Log.
Sender Based Rate Control, including specifying email addresses you wish to exempt, is configured on the BLOCK/ACCEPT > Rate Control p
age.
151
IP Analysis Outbound
en
After applying rate controls, the Barracuda Spam Firewall performs analysis on the IP address, applying quarantine, block, encrypt or redirect
policies that you configure in the BLOCK/ACCEPT pages.
BLOCK/ACCEPT policies created at the per-domain level do NOT apply to outbound messages. So, for example, navigating to the DOMAINS pa
ge, then clicking Manage Domain for a particular domain, then configuring policies on the BLOCK/ACCEPT pages ONLY applies to inbound
messages for that domain.
Once the true sender of an outbound email message is identified, the intent of that sender should be determined before accepting the message
as valid, or "not spam". The best practice is to know the IP addresses of trusted senders and forwarders of email and define those on the
Barracuda Spam Firewall as "Allowed" by adding them to a whitelist of known good senders. Various methods for discerning "good" senders of
email versus spammers are described in this section to help you to quickly configure your Barracuda Spam Firewall per the needs of your
organization.
Barracuda Networks does NOT recommend whitelisting domains because spammers will spoof domain names. When possible, it is
recommended to whitelist (Allow) by IP address only.
152
Sender and Recipient Filtering Outbound
en
If any of the computers in your organization get infected with a botnet or other malware, it can send out spam emails, thereby possibly landing
your domain(s) or IP address(es) on a blocklist, not to mention spreading the malware. Use the BLOCK/ACCEPT > Sender Filters page to
control which domains and email addresses can send email out through the Barracuda Spam Firewall. Note that both inbound and outbound
email messages from whitelisted ("allowed") domains/subdomains bypass spam scoring as well as all other blocklists, but do go through virus
checks.
Adding your own domain to the sender whitelist is not allowed because spoofing the domain of the recipient is a frequently used
spamming technique. Instead, add the IP address of your mail server(s) to the Allowed IP/Range list using the BLOCK/ACCEPT > IP
Filters page.
Email addressed from specified email addresses and domains/subdomains can also be encrypted or redirected from the BLOCK/ACCEPT >
Sender Filters page.
Outbound email addressed to specified email addresses (recipients) or domains/subdomains can also be allowed, blocked, encrypted or
redirected from the BLOCK/ACCEPT > Recipient Filters page.
For more information about email encryption and redirection, see Encryption of Outbound Mail 6 and Above.
153
en
The Barracuda Spam Firewall does a reverse DNS lookup on inbound and outbound IP connections and finds the hostname associated with the
IP address of the sender. By configuring rules on the BLOCK/ACCEPT > Reverse DNS page, you can choose to apply Common Reverse DNS
Rules by country or create Custom Reverse DNS Rules to quarantine or block outbound messages from those domains.
Blocking by Top Level Domain (TLD)
The last part of a hostname is known as the top level domain, or TLD. Most TLDs include a country identifier, such as .ca for Canada, .ru for
Russia, etc. If most or all of the mail that you receive from a particular country is spam, you can use the Common Reverse DNS Rules to tag
(inbound only), block or quarantine any message that has an associated hostname that includes that country's TLD. Email which is not blocked is
subject to all of the usual spam and virus checks.
Whitelist Override for TLDs
Use the Custom Reverse DNS Rules to quarantine or block outbound messages from hostnames ending with values that you specify. List the
sending domains or subdomains you want to whitelist on the BLOCK/ACCEPT > Sender Filters page. You can use the Custom Reverse DNS
Rules to whitelist all or part of a hostname from which you want to always allow mail, both inbound and outbound. With the whitelist option you
can thereby override the Common Reverse DNS Rules settings for TLDs. If you have blocked any TLDs in Common Reverse DNS Rules, for
example, you can use the Custom Reverse DNS Rules whitelist option to allow mail from one or more hostnames within that TLD.
Messages With a Missing PTR record
Use the Block Missing PTR Records setting to enable blocking mail from IP addresses with no PTR (reverse DNS) record defined.
Caution
Many mail servers do not have their reverse DNS configured properly, which may cause legitimate mail to be blocked when Block
Missing PTR Records is set to Yes.
154
Content Analysis Outbound
en
In this Article:
en
Attachment Content Filtering
DLP and HIPAA Compliance
Intent Analysis
Image Analysis
Custom content filtering based on the subject line, message headers, message body and attachment file type can be applied to outbound mail
just as it can be to inbound mail. See the filtering pages on the BLOCK/ACCEPT tab for details on settings. Note that, in addition to block and qu
arantine, filter actions for outbound mail include encrypt and redirect.
See Regular Expressions for text patterns you can use for advanced filtering. Note that HTML comments and tags imbedded between characters
in the HTML source of a message are filtered out so content filtering applies to the actual words as they appear when viewed in a web browser.
Attachment Content Filtering
All outbound messages, including those from whitelisted senders, go through attachment filtering. You can block, quarantine, encrypt or redirect
outbound messages that contain attachments which include text matching the patterns you enter here. Attachment Content Filtering is limited to
text type files such as MS Office files, html, pdf files and other document files. A notification will be sent to the sender when an outbound
message is blocked due to attachment content filtering.
DLP and HIPAA Compliance
You can also take actions with outbound messages that contain matches to pre-made patterns in the subject line, message body or attachment.
With information types such as:
Credit card patterns,
Social security numbers (USA only),
Combinations of privacy information such as birthday and driver’s license, and
Diagnosis/prognosis as defined under HIPAA
...the Barracuda Spam firewall can filter attachment content and encrypt, block, quarantine, allow or redirect messages as configured on the BLO
CK/ACCEPT > Content Filters page. Note that the format of this data varies depending on the country, and these filters are more commonly
used in the U.S.; they do not apply to other locales.
Outbound messages can undergo Fingerprint Analysis if you enable this feature for both inbound and outbound mail on the BASIC > Spam
Checking page. In order to detect real-time spam fingerprints, Barracuda Real-Time Protection must be enabled on the BASIC > Virus
Checking page.
Engineers at Barracuda Central work around the clock to identify new spam fingerprints which are then updated on all Barracuda Spam Firewalls
through hourly Barracuda Energize Updates.
Intent Analysis
As for inbound mail, this feature is applicable for outbound mail, and block or quarantine actions can be specified accordingly on the BASIC >
Spam Checking page.
Image Analysis
Fingerprint Analysis captures a significant percentage of images after they have been seen, while Image Analysis techniques protect against new
image variants. The techniques detailed in Image Analysis (Inbound Mail) also apply to outbound messages. Image Analysis is configured on the
BASIC > Spam Checking page.
155
Attachment Filtering Outbound
en
Attachment filtering based on filename patterns you specify, common text attachment file types and attachment MIME types can be applied to
outbound mail just as it can be to inbound mail. See the BLOCK/ACCEPT > Attachment Filters page for details on settings. Note that, in
addition to Block and Quarantine, filter actions for outbound mail include Encrypt and Redirect.
See Regular Expressions for text patterns you can use for advanced filtering. You can also specify one of the actions listed above to take with
outbound messages if attached archive files (zip,tar, etc.) require a password to unpack.
156
Bayesian Analysis Outbound
en
Outbound mail traffic from the Barracuda Spam Firewall undergoes Bayesian scoring just as inbound mail does. For details on how Bayesian
scoring works, see Bayesian Analysis Inbound. Note that to 'train' your Bayesian database to most accurately determine what you or your user(s)
consider to be spam or 'not spam', at least 200 messages of each kind of inbound mail (spam and 'not spam') must be identified. Users can use
the Barracuda Outlook Add-in with their MS Outlook client which provides convenient buttons to click for identifying selected messages as either
spam or 'not spam'. See the Barracuda Outlook Add-In Overview for details.
Advanced Configuration
en
In this Section
Remote IMAP/POP Accounts
Advanced Networking
Non-Delivery Reports
Remote Administration
157
158
en
This is a key feature of the Barracuda Spam Firewall for protecting your network and users from spammers who might "spoof" a domain or
otherwise hide the identity of the true sender. The following techniques are used to verify the "from" address of a message.
Mail Protocol (SMTP) Checking
The Barracuda Spam Firewall can perform thorough checks on incoming email for RFC 821 compliance, require mail clients to introduce
themselves with an SMTP "HELO" or "EHLO" command before stating a sender, and otherwise manage SMTP protocol to block spammers. See
the ADVANCED > Email Protocol page for these and other optional SMTP settings.
Sender Spoof Protection
The Barracuda Spam Firewall has the option to prevent "spoofing" of an organization’s own domain by blocking emails with that domain name in
the "From" field that are sent from outside the organization. Note that sender spoof protection should not be enabled if the organization sends
messages from outside their internal email infrastructure (e.g., in the case of marketing bulk-mail services).
The Sender Spoof Protection feature can be configured at the global level from the ADVANCED > Email Protocol page or at the per-domain
level on the DOMAINS > Manage Domain > ADVANCED > Email Protocol page. At the domain level, however, this feature is labeled as Rejec
t messages from my domain.
Note that if the administrator enables Sender Spoof Protection at the global level it will supersede any whitelist entry created at the per-user
level by a User, Helpdesk or Domain Admin account holder.
Invalid Bounce Suppression
The Invalid Bounce Suppression feature is used to determine whether or not the bounce address specified in a message is valid. It is designed
to reduce the number of bounce messages to forged return addresses; i.e., you don’t want to get bounced messages from spammers who spoof
your domain or email address. Every email sent from the Barracuda Spam Firewall is tagged with an encrypted password and expiration time.
With Invalid Bounce Suppression enabled, any bounced email received by the Barracuda Spam Firewall that does not include that tag is
blocked. Each blocked message is recorded in the Message Log with the reason "Invalid Bounce"
To use the Invalid Bounce Suppression feature, the Barracuda Spam Firewall must have Outbound Relay configured on the BASIC >
Outbound page. For more details about Outbound Relay, refer to How to Route Outbound Mail From the Barracuda Spam Firewall.
Configure Invalid Bounce Suppression on the BLOCK/ACCEPT > Sender Authentication page and enter a Bounce Suppression Shared
Secret as a non-null password which will be included in the headers of valid emails sent from and bounced back to the Barracuda Spam Firewall.
Email bounces that don’t include the password will be blocked if this feature is enabled. In a clustered environment, the Bounce Suppression
Shared Secret will be synchronized across all Barracuda Spam Firewalls in the cluster.
Sender Policy Framework (SPF)
Sender Policy Framework (SPF) is an open standard specifying a method to prevent sender address forgery. The current version of SPF protects
the envelope sender address, which is used for the delivery of messages. SPF works by having domains publish reverse MX records to display
which machines (IP addresses) are designated as valid mail sending machines for that domain. When receiving a message from a domain, the
recipient can check those records to make sure mail is coming from a designated sending machine. If the message fails the SFP check, it may be
spam. Enabling this feature does create more performance overhead for the system due to the multiple DNS queries needed to retrieve a
domain's SPF record; for this reason, the default setting for the Enable SPF feature on the BLOCK/ACCEPT > Sender Authentication page is
No (off). For more information on SPF, please visit http://www.openspf.org.
Messages that fail SPF check can be tagged or blocked and will be logged as such. Messages that pass SPF checks will still be scanned for
spam. The recommended setting is to Tag messages identified by SPF as spam so that if there is any possibility that a message is
legitimate, it will be allowed to go on to the next stage of processing.
Exemptions from SPF Checking - Trusted Forwarders
You may specify a list of Trusted Forwarder IP addresses, on the BASIC > IP Configuration page, which will be ignored when performing SPF
checks, as well as rate control and IP Reputation checks. Trusted Forwarders are mail servers that are set up specifically to forward email to the
Barracuda Spam Firewall from outside sources. The Barracuda Spam Firewall scans the IP addresses in the Received From headers list of each
email and performs an SPF check on the first IP address that is not in the list of Trusted Forwarders.
Domain Keys (DKIM) Inspection
DomainKeys is a method of email authentication that enables a sending domain to cryptographically sign outgoing messages, allowing the
sending domain to assert responsibility for a message. When receiving a message from a domain, the Barracuda Spam Firewall can check the
signature of the message to verify that the message is, indeed, from the sending domain and that the message has not been tampered with.
159
Because most spam messages contain spoofed addresses, DomainKeys can help greatly in the reduction of spam.
DomainKeys uses a public and private key-pairs system. An encrypted public key is published to the sending server's DNS records and then
each outgoing message is signed by the server using the corresponding encrypted private key. For incoming messages, when the Barracuda
Spam Firewall sees that a message has been signed, it will retrieve the public key from the sending server's DNS records and then compare that
key with the message's DomainKeys signature to determine its validity. If the incoming message cannot be verified, the Barracuda Spam Firewall
knows it contains a spoofed address or has been tampered with or changed.
The benefits of enabling this feature include:
Email sender is validated
Email body is validated
Validation through DNS is difficult to foil
DomainKeys works well with email forwarding because it doesn’t deal with the relay server IP address
You can choose to tag, block or quarantine both DKIM signed messages that fail the DKIM database check as well as unsigned messages,
depending on how you configure DomainKeys Inspection on the BLOCK/ACCEPT > Sender Authentication page. You can also exempt
domains from being tagged, quarantined or blocked if they fail this check. As stated elsewhere in this guide, it is safest to NOT exempt domain
names from any kind of spam filtering due to the possibility of domain name spoofing by spammers.
DomainKeys inspection does require more CPU resources to encrypt & decrypt the key and is turned off by default. Messages that pass DKIM
checks will still be scanned for spam.
Custom policies
Organizations can define their own allowed sender domains or email addresses for sender authentication using the BLOCK/ACCEPT > Sender
Filters page, but the safest way to indicate valid senders on the Barracuda Spam Firewall is to whitelist (allow) the IP addresses of trusted email
servers on the BLOCK/ACCEPT > IP Filters page, then blocklist (block, quarantine or tag) their domain names on the BLOCK/ACCEPT >
Sender Filters page to prevent domain name spoofing.
160
en
LDAP Lookup
On the Barracuda Spam Firewall 300 and higher, email recipients can be validated with your existing LDAP server. Configuration of LDAP lookup
is done at the domain level. From the DOMAINS > Domain Manager page, after clicking Manage Domain for the selected domain, you’ll
configure LDAP on the USERS > LDAP Configuration page. See the online help on that page for details about entering your server details. If
LDAP is not configured, the Barracuda Spam Firewall will do SMTP recipient verification through RCPT TO commands.
LDAP server types supported include Active Directory, Novell eDirectory, Domino Directory and OpenLDAP.
Explicit Users to Accept For (Valid Recipients)
If LDAP lookup is not being used for recipient verification, the Barracuda Spam Firewall provides a local database with which email recipients can
be compared for validation. Valid Recipients (Explicitly Accepted Users) can be specified either at the global level from the ADVANCED >
Explicit Users page or at the per-domain level from the DOMAINS > Domain Manager > USERS > Valid Recipients page. Note that the
number of entries in the text box for Explicitly Accepted Users and Alias Linking is limited by model: on the Barracuda Spam Firewall 600 and
lower, the maximum is 1000 per domain, and on the Barracuda Spam Firewall 800 and above, the limit is 5000 per domain.
To administer the local database, either at the global or domain level, fill in the text box in the Explicit Users to Accept For section of the page,
entering each email address for which the Barracuda Spam Firewall should accept email. If you select Yes for the Only accept email for these
recipients feature, email will REJECTED for any email recipients not in the list. Note that domain-specific lists override the global list.
Alias Linking
Alias linking allows quarantined email from multiple accounts to be directed to one account when using per-user quarantine. In the ADVANCED >
Explicit Users page you can specify the email addresses to be linked together in the Explicit Users to Accept For and Alias Linking text box.
See the online help on that page for more details.The quarantine account for all of the linked email addresses will be associated with the first
email address. Make sure to also enter the first email address on a separate line as well. In this way, a "catchall" account can be created to
receive all quarantined emails from a particular domain.
161
Remote IMAP/POP Accounts
en
The Barracuda Spam Firewall provides an email-retrieval and forwarding utility which fetches email from remote mail servers and forwards it to
your local machine's delivery system. You can repeatedly poll each account at a specified interval. This utility can gather mail from servers
supporting POP3 and IMAP and is configured from the ADVANCED > Remote IMAP/POP page.
Note that all email will be DELETED from the remote mail server after retrieval by the Barracuda Spam Firewall.
There are two types of operations for each account from which the Remote Accounts utility retrieves mail: Global and User. With the User type,
it is assumed that all messages in the user's account are intended for a single recipient. The Global type is used when multiple recipients under
the same domain are specified for a particular server account.
From the ADVANCED > Remote IMAP/POP page you can specify polling interval, SSL (yes/no), user account passwords and email addresses.
162
Advanced Networking
en
Port Forwarding
If your organization has a single public IP address, when you install the Barracuda Spam Firewall between the Internet and your mail server, you
can forward incoming SMTP traffic (port 25) from port 80 on the Barracuda to your mail server using the Port Forwarding feature from the ADVA
NCED > Advanced Networking page.
Configuring the Network Interfaces
With the Barracuda Spam Firewall 600 and higher, you can configure each of the two Ethernet (NICS) interfaces directly from the ADVANCED >
Advanced Networking page to accept email on both interfaces or to route ingress email to one NIC and egress through the other NIC. Benefits
of this feature include redundancy, filtering email for domains on separate networks and improving throughput. Up to 250 IP addresses can be
configured per NIC.
Static Routes
With the Barracuda Spam Firewall 600 (and 600Vx) and higher, you can specify a default gateway between the Barracuda Spam Firewall and a
mail server on another subnet in your organization using the Static Routes feature on the ADVANCED > Advanced Networking page. This will
guarantee that return traffic is routed back to the Barracuda Spam Firewall from the unassociated network. If you have problems with static route
configuration, please contact Barracuda Networks Technical Support.
Loopback Adapter
If you want to use this Barracuda Spam Firewall with a Barracuda Load Balancer in Direct Server Return mode, you must enable a non-ARPing
loopback adapter. If you are using any other mode you do not need to make any changes to the Barracuda Spam Firewall configuration.
Each Virtual IP address supported by the Real Server (the Barracuda Spam Firewall in this case) requires its own loopback adapter. For each
loopback adapter, enter a Virtual IP address in the Loopback Adapter Configuration field on the ADVANCED > Advanced Networking page.
163
Non-Delivery Reports
en
Spam Bounce Non-Delivery Reports (NDRs)
The Barracuda Spam Firewall sends NDRs to email recipients and senders when one of their messages is blocked. The NDR contains a brief
explanation of why the Barracuda Spam Firewall blocked the message. Information that you may want to add to an NDR includes the contact
information of the Barracuda Spam Firewall administrator so that internal users know who to contact if they have questions about a blocked
message.
The ADVANCED > Bounce/NDR Messages page in the Barracuda Spam Firewall web interface allows for customizing the information in an
NDR and for selecting the default language to use in the message.
Reducing Backscatter
By default, your Barracuda Spam Firewall is configured to NOT send an NDR to a sender when the Barracuda Spam Firewall blocks their email
(see the NDR on Block setting on the ADVANCED > Bounce/NDR Settings page). You may want to enable NDRs to alert legitimate senders
that their message has not been delivered to the recipient. However, if the email came from an illegitimate source such as a spammer, then
sending a bounce notification is not necessary.
Additionally, many spammers spoof valid domains, and you don’t want to send bounce messages to your domain if it is being spoofed. Sending
bounce messages to illegitimate senders, or to senders who were spoofed and did not actually send the offending message, is known as
“backscatter”. Backscatter can increase the load on your Barracuda Spam Firewall and may generate a lot of email to fake addresses or to
senders whose email addresses were spoofed by a spammer. Your domain could also end up on a real-time blocklist as a consequence.
If your Barracuda Spam Firewall rarely blocks a legitimate email, consider setting NDR on Block to No for Inbound and/or Outbound mail to
reduce backscatter.
164
Remote Administration
en
Barracuda Networks provides a set of APIs for remote administration and configuration of the Barracuda Spam Firewall. The APIs work through
manipulation of variables inside of the system configuration database, and anything that can be declared in that database can be set or checked
with the APIs. This includes most things that you can set by clicking the Save Changes button in the Barracuda Spam Firewall web interface. For
example, from the BASIC > Spam Checking page, you can set global Spam Scoring Limit values for the actions Block, Tag or Quarantine, then
click the Save Changes button. These values can be set remotely using the APIs.
The framework of the API provides for the programmer to get or set variables inside an XML-RPC request that correspond to field values in the
configuration database in the Barracuda Spam Firewall. Some languages such as Perl, for example, provide wrappers for XML-RPC requests,
providing an interface to form the request. To view the variables and current settings of the Barracuda Spam & Firewall configuration database,
on the ADVANCED > Backup page, select System Configuration for Backup Type and click the Backup button.
To prepare the Barracuda Spam Firewall for use with the APIs, you must first enter the IP addresses that are allowed to communicate with the
APIs in the Allowed SNMP and API IP/Range field on the BASIC > Administration page, and you must create an API Password that will be
included with all calls to the APIs. For more information on using the APIs, see the Barracuda Spam Firewall API Guide.
165
Creating and Managing Domains
en
Your Barracuda Spam Firewall will only accept emails addressed to domains that it has been configured to recognize. Settings for individual
domains can be configured by the administrator and, with some restrictions, by the Domain Admin and Helpdesk account roles as described in
Roles and Navigating the Web Interface. All three roles will see a DOMAINS tab from which they can click Manage Domain next to the domain
for which to edit the domain-level settings.
Only an administrator can add or delete domains using the controls available in the DOMAINS page. The administrator can also add domains
from the BASIC > IP Configuration page. Domains added from either page will be initially configured with whatever you have specified your
default global settings to be.
If the administrator deletes a domain, all user accounts associated with that domain will also be deleted from the Barracuda Spam Firewall. A
confirmation dialog box will prompt you to confirm whether or not you want to delete a domain.
Clicking the Manage Domain link for a particular domain will show some or all of the BASIC, USERS, BLOCK/ACCEPT, OUTBOUND
QUARANTINE and ADVANCED tabs, depending on the permissions level of the logged in account role.
Figure 1: The administrator can add domains on which to filter email.
Domain Level Settings
Some settings are only configurable at the domain level, while others are configurable at both the global and domain levels, with the domain level
setting taking precedence.The Domain Admin role or the Admin role can override some global settings for spam and virus checking and
quarantine at the domain level.
Setting values on a per-domain basis overrides the values configured at the global in the web interface. However, if you have never
changed a particular setting for a domain, any global level changes to that feature will be applied for that domain. This also means that
any changes you make to the global values of the Barracuda Spam Firewall will NOT be inherited by the domains that you edit and for
which you have changed configuration values.
Basic configuration of a domain consists of identifying the name of the domain (and/or a specific sub-domain) and specifying a destination mail
server. Additional settings available for a domain are dependent on the model of your Barracuda Spam Firewall, and can include any or all of the
following:
Destination Mail Server
Enabling of spam scanning and setting spam score limits for the domain
Enabling or disabling virus scanning
Per-user quarantine enable/disable
Control over which features users can see and configure for their accounts (see Controlling Access to Account Features).
A defined global quarantine email address (for the domain only)
Option to reject messages from same domain name. If set to Yes, the Barracuda Spam Firewall will reject email where the FROM
envelope or header address domain matches the domain (in the TO address). This feature provides protection from 'spoofing' of the
domain.
Option to require an encrypted TLS connection when receiving email from either ALL or specified domains. See the ADVANCED >
Email Protocol page at the domain level for details.
Option to require an encrypted TLS connection when relaying email to specified destination domains. See the ADVANCED > Email
Protocol page at the domain level for details.
IP address/range, Sender domain, Sender email and Recipient filtering. Note: BLOCK/ACCEPT policies created at the per-domain level
166
do NOT apply to outbound messages - they only apply to inbound messages for that domain.
LDAP configuration
Option to specify local database of valid recipients (if not using LDAP) and alias linking
Single Sign-On with various authentication mechanisms
Emailreg.org: option to require header, body or subject content filtering on mail from registered email addresses
Ability to validate the domain and specify an image for branding encrypted email messages and notifications sent to the recipient. Note
that encryption policy can only be set at the global level by the administrator.
The Barracuda Spam Firewall 400 and higher contains support for APIs that can be used to automate the steps for creating and
configuring multiple domains on the Barracuda Spam Firewall.
Managing Inbound Quarantine
en
In this Section
How Quarantine of Inbound Mail Works
Quarantine Options
Controlling Access to Account Features
How Quarantine Notifications Work
Retention Policy and Purging Old Messages
167
168
How Quarantine of Inbound Mail Works
en
After a message travels through the initial filtering layers of the Barracuda Spam Firewall, it is assigned a score based on the probability that it is
spam. The administrator can decide how to deal with messages based on the Spam Scoring levels (from 0 to 10): allow, tag, quarantine or
block, as set on the BASIC > Spam Checking page.
Tagging the message means the user will receive the message in their regular mailbox with the subject text modified to indicate that the
message might be spam.
Quarantining the message means that the message will either be delivered, with the subject text modified to indicate that the message
might be spam, to a special "quarantine inbox" assigned to a user or to a "global" quarantine mailbox designated by the administrator.
Blocking the message means it will not be delivered.
Messages can also be determined to be quarantined (as opposed to allowed, blocked or tagged) by custom policies you set based on domain
name, IP address, region, content filters and other filtering tools in the BLOCK/ACCEPT pages. Spam Scoring and some block/accept policy
settings can be further refined at the domain level and/or per-user level, depending on what the administrator enables on the USERS > User
Features page at the global level and what the Domain Admin role enables on the USERS > User Features page at the domain level. For more
information on the Domain Admin and other account roles, please see Roles and Navigating the Web Interface.
Quarantine can be enabled or disabled completely. If it is enabled at the global level, no messages are stored on the Barracuda Spam Firewall;
rather, all quarantined mail is sent to the Quarantine Delivery Address you specify on the BASIC > Quarantine page. If it is enabled at the
per-user level, user accounts are created on the Barracuda Spam Firewall for users listed either in the authentication server (see Automatic
Account Creation) or in the local database on the Barracuda Spam Firewall. Quarantined messages need to be received and determined to either
be delivered to the user’s regular email inbox or deleted.
As the administrator, you can configure a Retention Policy to limit the amount of disk space used for storing each user's quarantined messages,
thereby conserving system resources on the Barracuda Spam Firewall. Alternatively, messages can be scheduled for regular purging based on
age and/or size (see Retention Policy and Purging Old Messages).
169
Quarantine Options
en
By default, the Barracuda Spam Firewall does not quarantine incoming messages, but you may want to enable quarantine if, for example, your
organization requires it, or if you want to reduce load on the mail server while giving users a chance to determine what they consider to be "spam"
or "not spam". There are three options available for configuring quarantine with the Barracuda Spam Firewall as described below, with the pros
and cons of each.
In this article:
en
Turning Quarantine Off
Using Global Quarantine
Using Per-user Quarantine
Where Do the Quarantined Messages Go?
Linking Domains for One Quarantine Inbox
The Quarantine Inbox
Alias Linking
Turning Quarantine Off
Barracuda Networks recommends disabling quarantine unless, for example, your organization has a business requirement to provide quarantine
of messages suspected to be spam or you don’t want those messages stored on the mail server. Disabling quarantine means less management
either by the administrator or by the user and, in the case of per-user quarantine, saves system resources that would otherwise be used to store
the messages until the user delivers or deletes them.
An alternative to using quarantine is tagging email that may be spam based on scoring or are otherwise identified as possible spam. Benefits
include:
No messages are stored on the Barracuda Spam Firewall, thus saving system resources
The user doesn’t have an extra quarantine inbox to manage
Tagged messages, with a keyword such as "[BULK]" prepended to the subject line, can be filtered by the subject line to a separate folder
for later examination by the user (see the BASIC > Spam Checking page and the BLOCK/ACCEPT pages to configure spam scoring
and criteria for tagging messages).
To disable Quarantine completely:
Check the Disable check box next to "Quarantine" in the Spam Scoring Limits section of the BASIC > Spam Checking page
Make sure nothing on the BLOCK/ACCEPT pages is set to Quarantine
Using Global Quarantine
With global quarantine there is almost no difference in use of system resources versus having quarantine turned off because messages aren’t
stored on the Barracuda Spam Firewall; they are forwarded to a mailbox as designated by the administrator. Global quarantine identifies email to
quarantine, rewrites the "From" address of the message and sends it to the Quarantine Delivery Address specified on the BASIC > Quarantine
page. The subject line of each message is prepended with the Quarantine Subject Text (for example, [QUAR], as specified on the same page).
Global quarantine does require some time and effort by the administrator to manage quarantined messages. Global quarantine can be enabled at
the system level or at the domain level.
Enabling global quarantine on the Barracuda Spam Firewall provides the administrator with complete control over how quarantined messages are
handled, and it saves system resources because messages are not stored on the appliance.
To set up global quarantine:
From the BASIC > Quarantine page, set the Quarantine Type to Global and configure settings as described below for global
quarantine.
From the BASIC > Spam Checking page, if you want messages to be quarantined based on score, make sure that the Disable check
box next to Quarantine in the Spam Scoring Limits section is NOT checked.
Set filters on the BLOCK/ACCEPT pages to Quarantine per your organization's policies.
Enter a Quarantine Delivery Address on the BASIC > Quarantine page.This mailbox can either be on the mail server that the
Barracuda Spam Firewall protects or a remote mail server. Note: If you have a Barracuda Spam Firewall 400 or above, you can specify
the quarantine delivery address on a per-domain basis by going to the DOMAINS tab and clicking the Manage Domains link, then using
the BASIC > Quarantine page for that domain to configure the address.
Messages determined to be quarantined by the Barracuda Spam Firewall will have the subject line prepended by the Quarantine Subject Text a
s entered on the BASIC > Quarantine page. The default text is [QUAR]. This allows you to identify quarantined messages when you have them
delivered to a mailbox that also receives non-quarantine messages.
Note that with global quarantine, users will have no control over whitelisting or blocklisting of email addresses, which they do have with
170
per-user quarantine. Allowing them this control by using per-user quarantine can help reduce the number of messages processed by
the Barracuda Spam Firewall. However, if using global quarantine, users can communicate domains, IP addresses or email addresses
that should be white or blocklisted to the administrator to configure at the global level.
Using Per-user Quarantine
Providing a user with a quarantine inbox gives them greater control over how their messages are quarantined, but also requires them to manage
their quarantine inbox on the Barracuda Spam Firewall. Since per-user quarantine entails storing quarantined messages on the Barracuda Spam
Firewall until the user delivers or deletes, them, you may want to only provide a quarantine inbox to a subset of power users. For details about
managing the quarantine inbox, please see the Barracuda Spam Firewall User's Guide - 5.x.
When enabling per-user quarantine on the Barracuda Spam Firewall, keep in mind that quarantined email stored on the Barracuda Spam Firewall
requires storage capacity, so system load will vary with the average size of emails.
If the email patterns of your organization are such that many emails include large attachments (as with architecture firms, marketing firms, etc.),
the system may push the edge of performance more quickly than if emails tend to be small in size. See the Mail/Log Storage indicator in the Per
formance Statistics pane of the BASIC > Dashboard page to monitor disk storage on the Barracuda Spam Firewall.
To set up per-user quarantine:
On the BASIC > Quarantine page, select the Quarantine Type to be Per-User and configure settings as described below for global
quarantine.
From the BASIC > Spam Checking page, if you want messages to be quarantined based on score, make sure that the Disable check
box next to Quarantine in the Spam Scoring Limits section is NOT checked.
Set filters on the BLOCK/ACCEPT pages to Quarantine per your organization's policies.
If Per-User quarantine is set by the administrator, the Domain Admin can either enable or disable Per-User quarantine at the domain level.
From the USERS > User Features page the administrator can choose to allow the user to decide whether to deliver quarantined messages to
their regular email address associated with their account or to their quarantine inbox. This can alternatively be decided for the user by preventing
them from accessing this setting. From this page the administrator can also allow the user to control their whitelist (allowed) and blocklist
(blocked) of email addresses.
For the Barracuda Spam Firewall 300 and higher, be sure to set a Retention Policy (see the USERS > Retention Policies page)
before enabling per-user quarantine in order to prevent running out of quarantine space.
Where Do the Quarantined Messages Go?
If the administrator sets Quarantine Type to Per-User on the BASIC > Quarantine page and the New User Quarantine State feature is set to O
n, the Barracuda Spam Firewall will automatically create quarantine accounts for all users listed in the authentication server or local database as
configured at the domain level. Account holders can then log into the Barracuda Spam Firewall and view their Quarantine Inbox to view and take
actions with quarantined messages.
If a user's quarantine inbox is disabled (by an administrator or a Domain Admin or Helpdesk account, or by the user), emails sent to that user that
would normally have been placed in quarantine will simply be delivered to the user's regular mailbox with the subject line prepended with a
quarantine tag.
Linking Domains for One Quarantine Inbox
In some cases it may be practical to direct all quarantined email to one quarantine inbox on the Barracuda Spam Firewall. You may employ one
or more "power users" to manage it, or allow all users to log in to the same inbox.
Using only one quarantine inbox for all users greatly simplifies management of per-user quarantine because you only have to configure user
features (from the BASIC > User Features page) for ONE inbox. The Linking Domains feature, configurable on the BASIC > Quarantine page,
allows the option for all domains protected by this Barracuda Spam Firewall be treated as if they were alternate names for the default domain
name for the system. So, for example, if the Default Domain for the system as specified on the BASIC > IP Configuration page is
mybarracuda.com, then [email protected] will be treated as [email protected] when determining user validity and preferences, and
will have a quarantine inbox under the name [email protected].
The Quarantine Inbox
When an account holder with the User role logs in to the Barracuda Spam Firewall they’ll see the QUARANTINE INBOX and PREFERENCES ta
bs. They can view and choose to whitelist, deliver or delete quarantined emails from the QUARANTINE INBOX page and configure their account
settings from the PREFERENCES page to the extent that their account permissions allow as described below under Controlling Access to
Account Features. Domain Admin and Helpdesk account holders will see the QUARANTINE INBOX and PREFERENCES tabs when they click
the Manage Account link in the upper-right corner of the web interface.
For details on how all account holders manage their quarantine inbox, please see the Barracuda Spam Firewall User's Guide - 5.x.
171
Alias Linking
This feature allows one quarantine account to receive quarantined email for multiple accounts, using the Explicit Users to Accept For section of
the USERS > Valid Recipients page. Note that this account, if entered on one line only with associated accounts for which it should receive
email, is not considered a Valid Recipient. This account needs to be added on a separate line to also be considered a Valid Recipient. The
quarantine account that receives quarantined email for other accounts does not need to belong to the same domain as the others.
172
Controlling Access to Account Features
en
When accounts are created by the Barracuda Spam Firewall, permissions are automatically assigned for users to manage their account features
based on what is configured on the USERS > User Features page in the Default User Features section. Domain Admin roles can further limit
user access to these features based on what the administrator has enabled at the global level.
For example, if the Whitelist/Blocklist feature is set to No (disabled) at the global level in the Default User Features section of the USERS >
User Features page, the Domain Admin role will not see or be able to control that setting for accounts in domains that they manage.
Configurable user account features include:
Quarantine Inbox – allow the account holder to enable their quarantine inbox on the Barracuda Spam Firewall, or disable it such that
quarantined message go to their regular email inbox.
Spam scanning – allow the account holder to enable or disable
Edit frequency at which quarantine notifications are sent to the account holder
Add addresses and domains to a whitelist or blocklist
Use Bayesian filtering
Allow account holder to set their own tag, quarantine and block levels according to spam scoring
If allowed permissions by the administrator, the Domain Admin can edit the Default User Features settings (i.e. disabling certain features that
were enabled at the global level by the administrator) at the domain level for account holders in the domain. The Helpdesk role does not have this
permission.
Overriding Default Account Features Settings
The User Features Override section of the USERS > User Features page allows you to make exceptions to the rules specified above for
particular account holders. Domain Admin and Helpdesk roles can view and set override of user feature defaults ONLY for features that are
enabled in the Default User Features section by the administrator. Consequently, nothing will appear on the USERS > User Features page for
Domain Admin and Helpdesk roles if all Default User Features options have been set to No by the administrator.
User overrides only apply when the domain level setting in Default User Features matches the global setting.
Assigning Quarantine Inbox Permissions to Selected Users
One of the most common scenarios for overriding quarantine settings is when you want to provide a few "power users" with a quarantine inbox on
the Barracuda Spam Firewall and have the rest of your users receive quarantine messages in their standard email inbox. Providing a user with a
quarantine inbox gives them greater control over how their messages are quarantined, but also requires them to manage their quarantine queue.
For this reason, you may only want to provide a quarantine inbox to a subset of sophisticated users. In this example, you would do the following:
Set the quarantine type to Per-user on the BASIC > Quarantine page.
Set the New User Quarantine State to Off so that accounts are not automatically created by the Barracuda Spam Firewall when needed
(for conditions under which new accounts can be automatically created, see Automatic Account Creation).
Enable the features you want those account holders to be able to manage for their accounts on the USERS > User Features page.
In the User Account text box in the User Account Create/Update section of the USERS > User Add/Update page, enter the email
addresses of the users you for whom you want to create a quarantine inbox and set Enable User(s) Quarantine to Yes in the same
section.
Set the Email New User(s) option to Yes to email login information to the new users.
If you enable user quarantine, you should remove any mailing lists you may have added on the ADVANCED > Explicit Users page and public
folders so no per-user accounts are created based on those email addresses.
173
How Quarantine Notifications Work
en
The Barracuda Spam Firewall can send notifications at predefined intervals and in selected languages to let users know that they have
quarantined messages. The notification interval and email address can be set at the global level on the BASIC > Quarantine page and
overridden at the domain level if allowed by the administrator. Because creating a quarantine digest for each user requires lots of system I/O, it is
recommended to set the Notification Start Time on the BASIC > Quarantine page to outside of peak traffic time frames during the weekday.
The default start time is 3:35pm (15:35). Users can override the Notification Interval of daily, weekly or never from their PREFERENCES tab if
enabled by the administrator.
Multiple quarantine notifications can be sent out in a 24 hour period to let users know that they have quarantined mail. Configure this option by
entering multiple times for Notification Start Time. Note that sending multiple notifications could affect system performance.
If you enable quarantine notifications, be sure to open port 8000 on your firewall (or whatever port you are using for the web interface) if
you want the Barracuda Spam Firewall to send quarantine notifications outside of the network.
It is a recommended to set the Quarantine Host value, which appears as the sending hostname in all quarantine and welcome emails from the
system. Using this hostname as opposed to the system IP address (default) ensures that users are able to reach the Barracuda Spam Firewall
from their old notifications even after any possible changes in IP addresses.
At the domain level, to enable users (including Domain Admin, Helpdesk and User roles) to manage quarantine notifications for their own
accounts, make sure the Enable User Features setting on the BASIC > Quarantine page is turned On. Account holders can then access
notification settings from their PREFERENCES > Quarantine page, overriding the global setting. The Default Language used in notification
emails can also be set from this page.
How the Quarantine Digest Works
The quarantine digest only goes out if new quarantined mail is saved in the user’s folder since the last notification cycle. Each day the quarantine
notification service runs for all users. If there is no new quarantined mail for a user since the last notification interval, or if a user has logged into
their account since the last notification interval, no quarantine digest will be generated and sent to that user for that same 24 hour period. Note
also that links in the quarantine digest for viewing, delivering, whitelisting or deleting a message from the quarantine inbox expire in 5 days from
the date the digest is sent out.
174
Retention Policy and Purging Old Messages
en
As the administrator, you can configure retention policy to limit the amount of disk space used for storing each user's quarantined messages,
thereby conserving system resources on the Barracuda Spam Firewall.
From the USERS > Retention Policies page, you can enable the user to easily schedule quarantined messages for regular purging based on
age (in number of days), disk space used (specified in kilobytes), or both. Setting the Age Limit to a 7-14 day range is recommended assuming
that older quarantined emails may lose importance with time.
Note that regardless of these settings, no messages younger than 3 days will be removed. For example, if the maximum size limit on email size is
10MB and a quarantined email has a 19MB attachment, the email will be retained for 3 days, giving the user time to examine and process that
email before it is automatically deleted by the Barracuda Spam Firewall.
Minimize Excessive Email Storage
It is recommended that users be trained to manage their own quarantine areas, since constant reliance on the Barracuda Spam Firewall to
automatically remove quarantined messages based on either age or disk usage may impact system performance.
The level at which performance is affected depends on the number of user quarantine areas that are kept on the Barracuda, the amount of email
that is quarantined each day, and the number of tasks the system performs (e.g., reporting, or body filtering).
Use the filters on the USERS > Account View page to quickly determine which users have the largest quarantine areas. Each account entry
shows Yes/No in the Quarantine column ("Yes" indicates per-user quarantine is in effect for that user) and number of Kbytes of email stored in
their quarantine inbox in the Size column. Individual user quarantine areas can be disabled from the USERS > Add/Update page so that any
repeat offenders can be prevented from utilizing the Barracuda Spam Firewall quarantine areas. When a user's quarantine is disabled, emails
sent to that user that would normally have been placed in quarantine will simply be delivered to the user's actual mailbox with the subject line
prepended with a quarantine tag.
When you enable retention policies, keep in mind that if your system has been accumulating email without retention policies for a
period of time, the first day retention policies are enabled results in an impact on system performance. The longer a system runs
without retention policies, the larger the performance impact. After the first day or two, the load stabilizes as the system is able to keep
large quarantine fluctuations to a minimum. Retention policies are run daily starting at approximately 02:30 AM.
175
Managing Outbound Quarantine
en
For outbound mail, there is no per-user quarantine mechanism on the Barracuda Spam Firewall as there is with inbound mail. Messages that
meet or exceed the scoring level you set on the BASIC > Spam Checking page for the quarantine of outbound messages, and messages that
violate outbound policies you have configured on various BLOCK/ACCEPT pages will be placed in outbound quarantine for the system. These
messages will be logged and can be viewed on the BASIC > Outbound Quarantine page. At the domain level, messages in outbound
quarantine can be viewed and managed by domain under DOMAINS > Manage Domain > OUTBOUND QUARANTINE > Outbound
Quarantine.
Configure outbound quarantine settings discussed here from the BASIC > Quarantine page.
Immediate notifications can be sent to the administrator via the specified Notification Address whenever an outbound message is placed into
quarantine. As with inbound quarantine notifications, a quarantine summary can be sent on a daily or weekly basis, if at all.
An Age Retention Policy can be specified for outbound mail, indicating when "old" quarantined outbound messages should be removed from the
Barracuda Spam Firewall. Use this option together with the Size Limit (KB) and Size Retention Policy to limit the amount of disk space allotted
on the Barracuda Spam Firewall for storing quarantined outbound mail. Regardless of these settings, quarantined outbound messages are
always retained for at least 3 days.
176
Creating and Managing Accounts
en
With the Barracuda Spam Firewall 300 and higher, you can enable per-user quarantine and the system will create user accounts to enable
access to quarantine settings and messages. The Barracuda Spam Firewall 600 and higher supports per-user account spam score settings.
There are two ways of creating user accounts on the Barracuda Spam Firewall - automatically and manually. Depending on how the administrator
configures the Barracuda Spam Firewall, user accounts may be configured to display a quarantine inbox for individual use, or accounts may only
provide users with the ability to manage their own whitelist and blocklist of email addresses and domains or spam scoring levels.
In this article:
en
Account Roles
Automatic Account Creation
When to Disable Automatic Creation of Accounts
Manually Creating User Accounts
Account Creation by Users
Single Sign-On and User Authentication
Assigning Features to User Accounts
Account Roles
In addition to the administrator account role, which includes permissions to configure all settings on the Barracuda Spam Firewall, four other
account roles with associated levels of permissions are available:
User, the default account role whose permissions are limited to managing their own quarantine account to the degree enabled by the
administrator.
Auditor, a unique account (you can only create one instance) whose role it is to monitor the Outbound Quarantine - deleting, rejecting
or allowing delivery of messages based on policy. This account already exists on the Barracuda Spam Firewall and must be enabled on
the BASIC > Administration page. Note that email privacy can be protected by limiting the Auditor account to only viewing message
entries, not actual message contents. Use the Secondary Authorization feature, configurable on the BASIC > Administration page.
Helpdesk (available on the Barracuda Spam Firewall 300 and higher), with increased permissions.
Domain Admin (available on the Barracuda Spam Firewall 600 and higher), the role with the most permissions other than the
administrator. This role can configure certain types of policy for the domains assigned to their account.
Thus you can delegate various levels of authority to members of your organization for administering quarantine accounts, monitoring outbound
quarantined mail and managing per-domain level settings on the Barracuda Spam Firewall.
Once accounts are created, each account (with the exception of Auditor) can be assigned a role other than the default User role from the USERS
> Account View page at the global level or at the per-domain level. This feature is especially useful for ISPs/web hosting providers to give
helpdesk and more sophisticated technical support personnel access to domain and per-user account configuration for groups of users. See Role
-based Administration for details on role-based permissions and web interface navigation.
Automatic Account Creation
The Barracuda Spam Firewall automatically creates accounts when all of the following conditions are met:
The New User Quarantine State feature is set to On on the BASIC > Quarantine page:
The administrator enables quarantine and sets quarantine type to Per-User on the BASIC > Quarantine page. For more information on
enabling quarantine, refer to Managing Inbound Quarantine.
The Barracuda Spam Firewall receives an email that needs to be quarantined, which triggers creation of the account.
The Barracuda Spam Firewall automatic account creation process is as follows:
1. Checks the recipient email address against the Local database or the LDAP server as specified at the per-domain level on the USERS >
Single Sign-On page (Barracuda Spam Firewall 400 and higher), as well as the Explicit Users to Accept For text box on the USERS >
Valid Recipients page. To increase security, you can configure the Barracuda Spam Firewall to validate the receiving email address
(using LDAP or the SMTP command RCPT TO) before it creates an account. This helps prevent the Barracuda Spam Firewall from
creating accounts for invalid users.
2. Creates a new account with User level permissions (See Roles and Navigating the Web Interface for more information about account
roles and permissions) for the recipient if the address does not exist. The Barracuda Spam Firewall uses the email address of the
recipient as the username of the account and auto-generates a password.
3. If Single Sign-On is not enabled, the Barracuda Spam Firewall sends the account holder an email with the login information so they can
access their quarantine inbox. With Single Sign-On enabled:
The account holder will be able to log into the Barracuda Spam Firewall with their regular network credentials.
The account holder can alternatively log in with an alias as well. If the per-domain Unify Email Aliases option is set to Yes, then
when a user logs in with an alias, that user will be directed to the primary account. Please see the USERS > LDAP
Configuration page at the per-domain level for details on this option.
4.
177
4. Places the quarantined message in the account holder’s quarantine inbox.
5. Sends a quarantine summary report to the account holder.
The settings chosen in the Default User Features section of the USERS > User Features page are applied to all new accounts that are
created.
When to Disable Automatic Creation of Accounts
If your LDAP server is running slowly, email will still be processed by the Barracuda Spam Firewall but unavailability of your LDAP server could
result in creation of invalid quarantine accounts for unverified users on the Barracuda Spam Firewall. In this case it may be preferable to disable
automatic account creation by setting the New User Quarantine State to Off from the BASIC > Quarantine page. User accounts can be
manually created in bulk as described below.
Another reason to disable automatic creation of accounts is that you may not want all of your users to have quarantine inboxes to manage,
access to whitelist/blocklist capabilities, etc. In that case, you can manually create user accounts for those individuals for whom it is appropriate,
as described in the next section.
Manually Creating User Accounts
In addition to the two cases mentioned above, you will want to manually create user accounts with the USERS > User Add/Update page when
you want to override the default quarantine, virus and spam checking settings for specific account holders. Creating the account before the
Barracuda Spam Firewall automatically creates it enables you to initially configure the account settings if they are different from the default
settings for other users.
The Barracuda Spam Firewall allows for account holders to manage various aspects of spam and virus checking and whitelist/blocklist behavior
for their email without having to manage a quarantine inbox on the system. By doing this you can enable global quarantine, but create per-user
settings for user control of spam and virus checking features.
For example, if you want your users to be able to maintain their own whitelists and blocklists of email addresses and domains, but you don’t want
to use resources on the Barracuda Spam Firewall to store quarantine messages, or you don’t want to have to train or depend on users to manage
their quarantine inboxes, you can easily create accounts from the USERS > User Add/Update page for one or more users and disable their
quarantine inbox(es). Then, on the USERS > User Features page, enable the features over which you want those users to have control by
entering the same list of new account names (email addresses) in the User Account(s): text box in the User Features Override section of the
page.
Account Creation by Users
Another way to manually create accounts on the Barracuda Spam Firewall is to use the Create New Password button on the login page which
new users can click to create an account with their email address as their username. Their password will be emailed to the email address they
enter in the username field.
Single Sign-On and User Authentication
Single Sign-On is a per-domain setting available on the Barracuda Spam Firewall 400 and higher.
If Single Sign-On is enabled for a particular domain, account holders associated with that domain can log into the Web interface of the Barracuda
Spam Firewall with their regular network credentials to manage their accounts.
When enabling Single Sign-On for a domain, you should also configure HTTPS/SSL Access Only at the global level on the ADVANCED >
Secure Administration page to protect the transmission of network passwords. See How to Enable SSL for Administrators and Users to
configure SSL on the Barracuda Spam Firewall 400 and higher.
Assigning Features to User Accounts
The USERS > User Features page enables the administrator to enable or disable user control over their account settings:
For newly created accounts, in the Default User Features section of the page
For existing accounts, in the User Features Override and the Default User Features sections of the page
These features provide the user’s ability to enable or disable the following:
Whitelist/blocklist of email addresses and domains
Quarantine inbox
Notification settings - email address for receiving a quarantine summary report, and notification intervals
Use of a personal Bayesian database
Spam scanning (on/off)
Setting spam tag, quarantine and block score levels (Barracuda Spam Firewall 600 and higher)
178
For all of the user features enabled by the administrator, the Domain Admin account role can override the global setting and disable any Default
User Features for newly created accounts. BOTH the Domain Admin and Helpdesk account roles can override the global settings for existing
accounts in the User Features Override section of the USERS > User Features page on a per-domain basis.
To enable account holders (including Domain Admin, Helpdesk and User roles) to edit preferences/user features for their accounts, make sure
that the Enable User Features setting on the per-domain BASIC > Quarantine page is turned On.
One of the most common scenarios for overriding quarantine settings is when you want to provide a few "power" users with a quarantine inbox on
the Barracuda Spam Firewall, with the rest of your users receiving quarantined messages in their standard email inbox. Those quarantined
messages will have a tag prepended to the subject line indicating that the Barracuda Spam Firewall suspects the message to be spam. See How
Quarantine of Inbound Mail Works for more information.
179
Role-based Administration
en
The Barracuda Spam Firewall offers several levels of 'scope' when accessing the web interface and configuring the system. This enables
delegation of tasks such as:
Domain Administration: Management of only domain-level settings for one or more domains that are protected by the Barracuda Spam
Firewall
Helpdesk duties such as supporting end-user management of quarantine inbox, passwords and associated preferences
Application of governance, risk management and compliance policies to outbound email content by managing messages in the outbound
quarantine log
Only the administrator (Admin) role has access to the global scope, with access to all settings. Administration of domain-level settings can be
delegated to the Domain Admin role, which has the most permissions, the Helpdesk role, with fewer permissions, or the Governance, Risk
Management and Compliance (GRC) Account role, which has very limited permissions and a specific role. Finally, the User role can only see and
manage their account, or quarantine inbox and related settings. See Role Descriptions for more detail. To create roles and to understand the
difference in navigating the web interface for the Admin versus other roles, see Roles and Navigating the Web Interface.
180
Roles and Navigating the Web Interface
enDepending on the login role, the links in the upper right corner of the web interface will indicate the login name and, if in the domain level
scope, the domain being managed, or the name of the user account. This article addresses navigation of the web interface for the Admin,
Domain Admin, Helpdesk and User roles. For more information about these roles, please see Role Descriptions. The GRC account provides a
special role with very limited scope, and exists only for the purpose of meeting governance, risk management and compliance policies of an
organization. For information about the GRC role, please see Governance, Risk Management and Compliance (GRC) Account Role.
The administrator can step into the domain level scope of the web interface, which is what the Domain Admin and Helpdesk roles will see, from
the DOMAINS page, by selecting a domain to manage. The DOMAINS page represents the "top level" of navigation of the web interface for Dom
ain Admin and Helpdesk roles, as shown in Figure 1.
Figure 1: The DOMAINS page as viewed by the Domain Admin or Helpdesk roles upon login.
Clicking on Manage Domain enables managing domain-level settings and user accounts for that domain. The Domain Admin or Helpdesk role
can "drill down" another level by selecting an account associated with that domain to edit from the USERS > Account View page (see Figure 2
below). Editing an account displays the quarantine inbox and preferences for the account, which is what the User role sees. Domain Admin and
Helpdesk roles can also edit their own personal account settings and quarantine inboxes.
Figure 2: Drilling down from the DOMAINS page to account level.
Figure 3: Links enable Domain Admin role to return to DOMAINS page or edit account.
Editing Accounts and Assigning Roles
181
182
From the USERS > Account View page in the global scope, the administrator can manage accounts (other than the Auditor account) for all
domains on the Barracuda Spam Firewall, editing account roles, deleting invalid accounts as needed and changing account passwords. The
USERS > Account View page displays role types and whether or not each account has quarantine enabled. Role permissions are described in
the next section. The GRC account is managed from the BASIC > Administration page.
Figure 4: Account View from global scope as seen by the administrator.
Note that links in the upper right of the page always indicate the login name of the current account holder, the Log Off link and, if applicable, links
to manage the system, domains or user accounts.
Clicking Edit Role brings up the Edit Role page, as shown in the figure below, for changing the account role from User (the default) to Helpdesk
or Domain Admin and assigning domains for Helpdesk and Domain Admin account holders to manage.
To grant a Helpdesk or Domain Admin role permissions to manage ALL domains configured on the Barracuda Spam Firewall, put the phrase
"all_domains" in the Managed domains for text box on the Edit Role page for that account as shown in Figure 6 below instead of listing
individual domains to manage.
Figure 5: The Edit Role page for assigning roles and domains to manage.
Figure 6: Assigning all_domains permissions on the Edit Role page.
183
Role Descriptions
en
In This Section:
Domain Admin Role
Helpdesk Role
User Role
Governance, Risk Management and Compliance (GRC) Account Role
184
185
Domain Admin Role
en
The Domain Admin role is available on the Barracuda Spam & Firewall 600 and higher and can configure all domain settings for designated
domains as well as account settings for account holders who have lesser permissions. This role includes Helpdesk level permissions and use
cases as described above plus the ability to:
View message contents (if privacy settings allow) for designated domains.
Enable or disable per-user quarantine at the domain level and, if per-user quarantine is disabled, specify a global quarantine email
address for designated domains.
Enable or disable various Default User Features for new accounts (see Controlling Access to Account Features) for designated
domains.
Domain Admin Role - All_Domains Permissions
The Domain Admin role has the above permissions for ALL domains configured on the Barracuda Spam Firewall if the Managed domains for te
xt box on the USERS > Account View > Edit Role page for this account holder includes the phrase "all_domains". In this case, all domains for
which the Barracuda Spam Firewall filters email will appear in the DOMAINS page.
A Domain Admin account holder with all_domains permission can also do the following:
Create or change the role of a Domain Admin account holder who does not have all_domains permissions.
Log into and manage the quarantine inbox of a Domain Admin who does not have all_domains permissions.
Create or edit a Helpdesk account with all_domains permissions.
Navigation of the web interface for the Domain Admin role follows the examples illustrated for the Helpdesk Role, plus the following.
Figure 1: The Domain Admin role can configure domain-level settings.
186
Helpdesk Role
en
This role is available for the Barracuda Spam Firewall 300 and higher and can manage basic account settings for accounts associated with one
or more domains and assist users with managing their quarantine inboxes. This role has the User level permissions plus the ability to:
Change or update user account settings in the domain(s) to which the helpdesk user is assigned, which includes users spam scoring,
whitelist/blocklist, quarantine enable/disable, notification and Bayesian filtering settings.
View the Message Log for the domain(s) managed and deliver quarantined messages. The Helpdesk role cannot, however, view the
body of messages in the Message Log.
Log into an account with lesser permissions and manage the associated quarantine inbox – mark as spam/not spam, deliver, whitelist or
delete messages.
View domain-level status and reports (with the exception of the daily False Positive and False Negative, which can only be generated at
the global level by the administrator).
Edit account roles for account holders with lesser permissions.
The Helpdesk role has the above permissions for ALL domains configured on the Barracuda Spam Firewall if the Managed domains for text box
on the USERS > Account View > Edit Role page for this account holder includes the phrase "all_domains".
A Helpdesk account holder with all_domains permission can also do the following:
Change the role of a Helpdesk account holder (to the User role) who does not have all_domains permissions.
Log into and manage the quarantine inbox of a Helpdesk or a Domain Admin who does not have all_domains permissions
If the Helpdesk account holder only administers a subset of all domains configured on the Barracuda Spam Firewall, only those domains will
appear in the DOMAINS page. Here, the Helpdesk account only administers two domains:
Figure 1: Helpdesk account holder sees a list of only domains that they manage.
Clicking on the Manage Domain link will show a subset of the web interface. The Helpdesk role sees basic email statistics, can view reports and
the Message Log for the selected domain and manage the quarantine inbox and settings for other account holders, depending on their
permissions level.
From the USERS > Account View page, the Helpdesk account holder can view and edit accounts and quarantine inboxes for the domain or
manage their own account.
Figure 3: USERS > Account View page: the Helpdesk role sees a list of the accounts associated with the domain.
187
For any account holders listed for the domain, the Helpdesk account holder can manage the quarantine inbox and some account settings, as
described above.
Example Helpdesk Use Cases
Disabling quarantine on the USERS > Add/Edit page for one or more users for reasons such as the following:
You don’t want to use Barracuda Spam Firewall resources to store quarantined email, but you want your users to maintain their
own whitelists and blocklists of email addresses and domains.
Users don’t want to maintain two inboxes, but want to control spam scoring and quarantine notification intervals for their
incoming email.
A User account holder needs help changing their password.
A User account holder needs to know why email from a particular address is getting blocked by the Barracuda Spam Firewall and the Hel
pdesk role can:
View the reason for blocking on the BASIC > Message Log page.
Deliver the message if necessary.
188
User Role
en
This is the default role assigned to newly created accounts on the Barracuda Spam Firewall, and only provides the account holder with a view of
their quarantine inbox and some account preference settings, depending on what has been enabled for their account. For details about managing
the quarantine inbox, please see Barracuda Spam Firewall User 's Guide 6 and Above.
User role permissions may include:
Modify individual settings for quarantine, spam tag and block levels.
Management of quarantine inbox - mark as Spam/Not Spam, deliver, whitelist, delete quarantined messages.
Change password (if Single Sign-On authentication is not configured).
Create whitelists and blocklists for email addresses and domains.
Manage a personal Bayesian database.
If granted the permission, the User role can disable quarantine for their account such that all messages quarantined for that account holder’s
email address(es) by the Barracuda Spam Firewall will be delivered to their regular email inbox. The User account holder will see the following
page upon login, with option to set preferences (see Assigning Features to User Accounts) and manage their quarantine inbox of messages. See
also Using Per-user Quarantine.
Figure 1: User role view of web interface, displaying the Quarantine inbox.
189
Governance, Risk Management and Compliance (GRC) Account Role
en
Beyond just protection from spam and viruses, the Barracuda Spam Firewall provides tools to protect sensitive personal, financial, medical, legal
data and intellectual property transmitted via email. The GRC role is a tool that provides DLP (data loss prevention) for your organization by
assigning one or more responsible persons with the task of viewing either message entries (Subject, From, To, etc.) or both the entries and the
message contents in the outbound quarantine log. The GRC can then decide whether to deliver, reject or delete emails from this log based on the
policies of the organization. In this way, the GRC role serves to provide governance, risk management and compliance to email content.
This account always exists on the Barracuda Spam Firewall, but must be enabled via the Enable GRC Account setting on the BASIC >
Administration page to be active. The administrator can enable or disable the GRC account at any time, but must re-create a password each
time the account is re-enabled. The GRC account only has access to Outbound Quarantine logs, and can take the following actions with
outbound quarantined messages:
Deliver – GRC determines that the message is allowed, per policy, and clicks the Deliver button.
Reject – GRC determines that the message is not allowed for delivery, per policy, and clicks the Reject button. If the Admin has
configured it on the ADVANCED > Bounce/NDR Settings page, this action sends a bounce message to the sender in addition to
deleting the message.
Delete – GRC determines that the message is not allowed to be sent and clicks the Delete button. The message will then be removed
from the Outbound Quarantine log.
Note that you must enter a new password each time you set Enable GRC Account to Yes.
When the GRC logs in, only two pages will be visible in the web interface: the Outbound Quarantine page and a Password page as shown in
Figure 1, below. From the Password page, the GRC can change the current GRC password.
Note that, to protect email privacy, the Secondary Authorization feature on the BASIC > Administration page can be configured to
require a password for the GRC role to be able to see message contents when monitoring the outbound quarantine. If Enable
Secondary Authorization is set to Yes and Include Privacy for GRC Account is also set to Yes, then the GRC must supply the
password to see message contents in the log.
Figure 1: The GRC role can view the Outbound Quarantine and Deliver, Delete or Reject messages.
Monitoring the System
en
In this Section
Basic Monitoring Tools
Reporting
How to Set Up Alerts and SNMP Monitoring
Using a Syslog Server to Centrally Monitor System Logs
How to Set Up Barracuda Cloud Control
Barracuda Spam Firewall Panel Indicators, Ports, and Connectors
Troubleshooting
190
191
Basic Monitoring Tools
en
In this article:
en
Viewing Performance Statistics
Inbound and Outbound Message Queues
Retrying All Outbound Messages
The Message Log
Using the Task Manager to Monitor System Tasks
Front Panel Indicator Lights
Viewing Performance Statistics
The BASIC > Dashboard page provides an overview of the health and performance of your Barracuda Spam Firewall, including:
Hourly and daily email statistics that display the number of viruses blocked and messages rate controlled (deferred), blocked,
quarantined, tagged (inbound only), sent (outbound only) and allowed (inbound only) for the last 24 hours and 28 days.
The subscription status of Energize Updates.
Performance statistics, including CPU temperature and system load. Performance statistics displayed in red signify that the value
exceeds the normal threshold. These values will fluctuate based on the amount of traffic that is being handled, but if any setting remains
consistently in the red for a long period of time, please contact Barracuda Networks Technical Support.
If the Mail/Log Storage rises above 75%, this indicates that more disk space has been taken up by the message and log storage than is
allocated for that purpose and you should contact Barracuda Networks Technical Support.
If per-user quarantine is enabled and system performance has decreased, check the Quarantined number of messages shown in the Email
Statistics [inbound] pane on the BASIC > Dashboard page. If this number is high, changing the Retention Policies for per-user quarantine on
the USERS > Retention Policies page may solve the problem. See Retention Policy and Purging Old Messages for details and warnings about
deleting large amounts of messages.
On the Barracuda Spam Firewall 600 and higher, if a disk drive in the RAID array exhibits a problem, the Redundancy (RAID) indicator will
highlight in red and show one of the drives as degraded with a link Click To Repair. Clicking this link will display a pop-up indicating the drive to
replace and an Ok button and a Cancel button. You must first replace the disk drive that indicates a problem before proceeding with the repair
operation. Please contact Barracuda Networks Technical Support if you need assistance.
Inbound and Outbound Message Queues
You can view the mail queues from the BASIC > Dashboard page with the In/Out Queue Size links.
The number of current inbound messages (In) plus accepted messages waiting for virus and spam scanning is shown, separated by a “/”, from
the number of messages in the outbound queue (Out) waiting for the outbound server. Click either number to view a summary of the messages
currently in the queues.
To view the queues in a Message Log format, with the ability to filter, requeue, delete and view details of selected queued messages, use the AD
VANCED > Queue Management page.
Retrying All Outbound Messages
If the outbound queue number is high, the mail server could be down or there could be another network issue. Messages in the outbound queue
will automatically expire if not successfully delivered within 48 hours (default). This may happen normally if the destination mail server rejects
email based on mail server policy and the message is bounced back to the sender.
To requeue, or retry delivering ALL email messages in the out queue, click the Retry button at the bottom of the BASIC > Administration page
to retry sending the messages immediately. The button will then be disabled until the requeue process has completed. To requeue, or retry
delivering selected email messages in the out queue, use the ADVANCED > Queue Management page.
Note that alerts and notifications are queued separately from email so that the administrator can be alerted if the out message queue is high.
The Message Log
The BASIC > Message Log page displays details about all email traffic that passes through the Barracuda Spam Firewall. Message source and
analysis is viewable by clicking on a message, and includes spam scoring and Bayesian analysis, if enabled.
This data is captured initially in the Mail Syslog and appears on the mail facility at the debug priority level on the specified syslog server.
The Message Log is a window into how the current spam and virus settings are filtering email coming through the Barracuda Spam Firewall, and
sorting data using the wide variety of filters can quickly provide a profile of email by allowed, tagged, quarantined or blocked messages by
domain, sender, recipient, time, subject, size, reason for action taken or score.
192
Watch the Message Log after making changes to the spam and virus settings to determine if the Barracuda Spam Firewall spam checking and
quarantine behavior is tuned per the needs of your organization. See Monitor and Classify Incoming Emails for more information about using the
Message Log.
Using the Task Manager to Monitor System Tasks
The ADVANCED > Task Manager page provides a list of tasks that are in the process of being performed and displays any errors encountered
when performing these tasks. Some of the tasks that the Barracuda Spam Firewall tracks include:
Clustered environment setup
Configuration and Bayesian data restoration
Removal of invalid users
If a task takes a long time to complete, you can click the Cancel link next to the task name and then run the task at a later time when the system
is less busy. The Task Errors section will list an error until you manually remove it from the list. The errors are not automatically phased out over
time.
Front Panel Indicator Lights
Unable to render {include}
The included page could not be found.
193
Reporting
en
Generate System Reports
The Barracuda Spam Firewall has a variety of system reports that can help you keep track of such statistics as the top spam senders and the top
viruses detected by the system.
Reports can be created for data collected at the global level as well as at the per-domain level. You can run reports and configure report settings
from the BASIC > Reports page, and online help for that page includes a table listing all reports, the kind of data each report includes for
inbound and/or outbound mail, and types of graphs available. You can either generate a system report on demand or schedule reports for regular
delivery to specific users.
On demand reports can cover data for a specified date range, but generating a report to view instead of to send as an email can potentially
consume excessive system resources on the Barracuda Spam Firewall. For this reason, discretion should be used when deciding on the date
range a given report is to cover. To minimize impact of report generation on the Barracuda Spam Firewall performance, reports of over 7 days in
length can only be generated through email.
Automate the Delivery of Scheduled System Reports
The Reporting Email Options section of the BASIC > Reporting page lets you configure the Barracuda Spam Firewall to automatically deliver
system reports daily, weekly or monthly to specific users by entering their email addresses in the field next to each report type.
You can enter as many email addresses as you like for each report as long as each address is separated by a comma. If you do not want a daily
report to be distributed, do not enter an email address next to that report type.
Each scheduled report covers traffic for the selected Date Range and Start and End times, and can be automatically generated either Daily,
Weekly or Monthly. The Traffic Summary report is a good status reporting tool, and having it emailed to your mail box every day is helpful for
monitoring the system.
194
How to Set Up Alerts and SNMP Monitoring
en
Setting up Emailed System Alerts
The BASIC > Administration page allows you to configure the Barracuda Spam Firewall to automatically email system notifications and alerts to
the email address(es) you specify. To enter multiple addresses, separate each address with a comma. Note that notifications are queued
separately from outbound messages. System alerts are sent from the Barracuda Spam Firewall to the System Alerts Email Address(es) you
specify when a system issue triggers an automated alert, including:
LDAP lookup or server errors. This alert email is sent once per day reporting LDAP errors logged over the past 24 hours. A few errors
may not be indicative of a problem, but more than a few may mean that there is mail that is being blocked for one or more invalid
recipients.
Failure of an automated backup. The email will indicate the cause of failure, such as, for example, the backup server is not available,
invalid username or invalid password. Check the settings on the ADVANCED > Backup page in the Automated Backups section.
Notifications are sent from Barracuda Central to the System Contact Email Address when:
Your Energize Update subscription is about to expire
Problems arise with RAID disk storage
New security bulletins are available
Setting up SNMP Query and Alerts
While the Barracuda Spam Firewall will send email alerts to the System Alerts Email Address specified on the BASIC > Administration page,
these alerts are limited and do not include latency, inqueue sizes, and other similar information. To monitor more specific information on a
Barracuda Spam Firewall, Barracuda Networks recommends using SNMP monitoring with an SNMP server. The Barracuda Spam Firewall 400
and higher offers the ability to monitor various settings via SNMP, including:
System statistics, such as:
inbound/outbound queue size
average email latency
encrypted, blocked, quarantined and tagged messages based on spam, custom policy, virus, etc. (outbound mail included)
appliance uptime
Performance statistics, including mail/log storage, CPU temperature and system load.
To query the Barracuda Spam Firewall for these statistics via SNMP, you must first enable the SNMP agent, specify the SNMP version you’re
using, the community string, and enter the IP address of the server(s) that will be making the SNMP connection in the SNMP Manager section of
the BASIC > Administration page.
To configure SNMP with the Barracuda Spam Firewall, see How to Use SNMP Monitoring.
195
How to Use SNMP Monitoring
en
This article applies to the Barracuda Spam Firewall 400 and higher, version 5.1 and above.
In addition to the system performance statistics on the BASIC > Dashboard page, you can use the Barracuda Spam Firewall SNMP agent with
your SNMP monitor to query the system for performance and email filtering statistics. You can also use SNMP monitoring to receive alerts (traps)
by email that report system load and other vitals of the Barracuda Spam Firewall.
In this article:
en
Step 1. Configure SNMP on the Barracuda Spam Firewall
Step 2. Configure SNMP/Email Notifications
Step 3. Get the MIB files for your SNMP monitor
SNMP Versions
Syntax for SNMP queries
Examples: Getting Mail and Performance Statistics
Objects and Traps
Step 1. Configure SNMP on the Barracuda Spam Firewall
1.
2.
3.
4.
Log into the web interface of the Barracuda Spam Firewall as the administrator.
Navigate to the BASIC > Administration page and, in the SNMP Manager section, set Enable SNMP Agent to Yes.
Click the Help button on the page for instructions on choosing the SNMP Version (see SNMP Versions below for details).
Set the Allowed SNMP IP/Range. Only the IP addresses/networks you enter here will be allowed SNMP access to the Barracuda Spam
Firewall.
5. Configure SNMP Traps and SNMP Threshold sections. Click the Help button for instructions.
Note that the Barracuda Spam Firewall communicates SNMP information using a community string of cudaSNMP by default. This
string can be changed for version 5.x and higher in the SNMP Manager section of the BASIC > Administration page.
Step 2. Configure SNMP/Email Notifications
In the Email Notifications of the page, you can optionally set the Barracuda Spam Firewall to send notifications to the System Alerts Email
Address via SNMP for these conditions:
The inbound message queue size exceeds normal thresholds
The outbound message queue size exceeds normal thresholds
The average latency exceeds normal thresholds
Problems with RAID disk storage
To receive email notifications about system health via SNMP:
1. Send SNMP/Email Notifications to Yes.
2. Enter a value for the System Alerts Email Address.
Step 3. Get the MIB files for your SNMP monitor
Click to download the Barracuda Spam Firewall SNMP MIB and the Barracuda Reference MIB. You can use reference objects included in these
MIBs for monitoring either from custom scripts or from your SNMP monitor. The MIB files can be viewed in your web browser by simply replacing
YOURBARRACUDA in the following links with the IP address of your Barracuda Spam Firewall:
http://YOURBARRACUDA:8000/Barracuda-SPAM-MIB.txt
http://YOURBARRACUDA:8000/Barracuda-REF-MIB.txt
SNMP Versions
The Barracuda Spam Firewall supports both SNMP versions v2c and v3. SNMP v2c queries and responses are NOT encrypted, so it is not as
secure as SNMP v3. With SNMP v3, traffic is encrypted and you can set up access control for specified users with passwords. Barracuda
recommends using version v3. You can configure which SNMP version you want to use as well as authentication and encryption methods for
v3 in the SNMP Manager section of the BASIC > Administration page of the Barracuda Spam Firewall web interface. Examples of snmpget
commands for both versions are shown below.
Syntax for SNMP queries
If you are using an SNMP monitor tool, all you need to do is import the MIBs as mentioned above into the SNMP monitor. You can refer to the
MIBs for the Object IDs (OIDs) that correspond to the type of status you want to monitor. Please refer to the objects and traps listed in the next
section.
196
If you are querying the Barracuda Spam Firewall from code, use the following syntax (where System IP or hostname or localhost is the IP
address of the Barracuda Spam Firewall). Note that, if using the snmpwalk command, if you don’t include an OID you will get a listing of all of the
OIDs in the MIB.
Examples: Getting Mail and Performance Statistics
The standard SNMP MIB reports the email traffic and performance statistics for the Barracuda Spam Firewall on an hourly, daily and monthly
basis. These examples demonstrate the syntax for using snmpget to obtain some of these measurements.
Example 1: Using SNMP v2, get the size of the inbound queue (number of current messages in the inbound queue waiting for virus and spam
scanning), where the OID for Inbound Queue is 1.3.6.1.4.1.20632.2.2 (see Objects and Traps below).
$ snmpget -On -v2c -c public 192.168.132.74 1.3.6.1.4.1.20632.2.2
SNMP Response:
.1.3.6.1.4.1.20632.2.2 = INTEGER: 0
Example 2: Using SNMP v3, calculate the size of the outbound queue (number of messages in the outbound queue waiting for the outbound
server (delivery) where the OID for Inbound Queue is 1.3.6.1.4.1.20632.2.3:
$ snmpget -On -v3 -a MD5 -x DES -A password -X password -l authPriv -u admin 192.168.132.74
1.3.6.1.4.1.20632.2.3
SNMP Response:
.1.3.6.1.4.1.20632.2.3 = INTEGER: 0
Objects and Traps
As you will see in the Barracuda Spam Firewall MIB, the system provides the following objects. Please see the online help in the Barracuda
Spam Firewall web interface for details on these settings.
OID
Object
Description
1.3.6.1.4.1.20632.2.2
inQueueSize
Number of messages waiting to be
processed by the Barracuda Spam Firewall.
1.3.6.1.4.1.20632.2.3
outQueueSize
Number of messages waiting to be sent to
the mail server. Note that alerts and
notifications are queued separately from
outbound email.
1.3.6.1.4.1.20632.2.4
deferredQueueSize
Number of messages deferred because they
could not be processed, and will be
requeued for processing.
1.3.6.1.4.1.20632.2.5
avgEmailLatency
Difference between the time a message was
received by the Barracuda Spam Firewall
and the time it is sent to the mail server.
1.3.6.1.4.1.20632.2.8
notifyQueueSize
Count of messages in the notification queue.
1.3.6.1.4.1.20632.2.9
encryptionEnabled
A flag that is set if encryption is enabled for
at least one domain.
1.3.6.1.4.1.20632.2.11
lastMessageDelivery
Time and date the last message was
delivered by the Barracuda Spam Firewall.
1.3.6.1.4.1.20632.2.12
uniqueRecipients
Number of unique recipients of mail
processed by the Barracuda Spam Firewall.
1.3.6.1.4.1.20632.2.13
systemLoad
Estimate of CPU and disk load on the
system.
1.3.6.1.4.1.20632.2.14
sysFanSpeed
System fan speed.
1.3.6.1.4.1.20632.2.15
cpuFanSpeed
CPU fan speed.
1.3.6.1.4.1.20632.2.16
cpuTemperature
CPU temperature.
197
1.3.6.1.4.1.20632.2.17
firmwareStorage
Amount of disk storage used for various
system components.
1.3.6.1.4.1.20632.2.18
maillogStorage
Amount of disk storage used for message
and log storage.
1.3.6.1.4.1.20632.2.19
raidStatus
The status of the RAID disk array: Fully
Operational, Degraded, Rebuilding.
1.3.6.1.4.1.20632.2.20
totalInboundBlocked
Total number of inbound messages blocked
since last system reset.
1.3.6.1.4.1.20632.2.21
dailyInboundBlocked
in the past 24 hours.
1.3.6.1.4.1.20632.2.22
hourlyInboundBlocked
in the past hour.
1.3.6.1.4.1.20632.2.23
totalInboundVirusBlocked
due to viruses since last system reset.
1.3.6.1.4.1.20632.2.24
dailyInboundVirusBlocked
due to viruses in the past 24 hours.
1.3.6.1.4.1.20632.2.25
hourlyInboundVirusBlocked
due to viruses in the past hour.
1.3.6.1.4.1.20632.2.26
totalInboundRateControlled
Total number of inbound messages deferred
due to Rate Control since last system reset.
1.3.6.1.4.1.20632.2.27
dailyInboundRateControlled
due to Rate Control in the past 24 hours.
1.3.6.1.4.1.20632.2.28
hourlyInboundRateControlled
due to Rate Control in the past hour.
1.3.6.1.4.1.20632.2.29
totalInboundQuarantined
Total number of inbound messages
quarantined since last system reset.
1.3.6.1.4.1.20632.2.30
dailyInboundQuarantined
quarantined in the past 24 hours.
1.3.6.1.4.1.20632.2.31
hourlyInboundQuarantined
quarantined in the past hour.
1.3.6.1.4.1.20632.2.32
totalInboundTagged
Total number of inbound messages tagged
1.3.6.1.4.1.20632.2.33
dailyInboundTagged
1.3.6.1.4.1.20632.2.34
hourlyInboundTagged
in the past hour.
1.3.6.1.4.1.20632.2.35
totalAllowed
Total number of inbound messages allowed
1.3.6.1.4.1.20632.2.36
dailyAllowed
1.3.6.1.4.1.20632.2.37
hourlyAllowed
in the past hour.
1.3.6.1.4.1.20632.2.38
totalOutboundPolicyBlocked
Total number of outbound messages blocked
due to policy since last system reset.
1.3.6.1.4.1.20632.2.39
dailyOutboundPolicyBlocked
due to policy in the past 24 hours.
1.3.6.1.4.1.20632.2.40
hourlyOutboundPolicyBlocked
due to policy in the past hour.
198
1.3.6.1.4.1.20632.2.41
totalOutboundSpamBlocked
due to spam since last system reset.
1.3.6.1.4.1.20632.2.42
dailyOutboundSpamBlocked
due to spam in the past 24 hours.
1.3.6.1.4.1.20632.2.43
hourlyOutboundSpamBlocked
due to spam in the past hour.
1.3.6.1.4.1.20632.2.44
totalOutboundVirusBlocked
due to viruses sincelast system reset.
1.3.6.1.4.1.20632.2.45
dailyOutboundVirusBlocked
due to viruses in the past 24 hours.
1.3.6.1.4.1.20632.2.46
hourlyOutboundVirusBlocked
due to viruses in the past hour.
1.3.6.1.4.1.20632.2.47
totalOutboundRateControlled
Total number of outbound messages
deferred due to Rate Control since last
system reset.
1.3.6.1.4.1.20632.2.48
dailyOutboundRateControlled
deferred due to Rate Control in the past 24
hours.
1.3.6.1.4.1.20632.2.49
hourlyOutboundRateControlled
deferred due to Rate Control in the past
hour.
1.3.6.1.4.1.20632.2.50
totalOutboundQuarantined
quarantined since last system reset.
1.3.6.1.4.1.20632.2.51
dailyOutboundQuarantined
quarantined in the past 24 hours.
1.3.6.1.4.1.20632.2.52
hourlyOutboundQuarantined
quarantined in the past hour.
1.3.6.1.4.1.20632.2.53
totalEncrypted
Number of messages sent to the Barracuda
Message Center for encryption and delivery
1.3.6.1.4.1.20632.2.54
dailyEncrypted
1.3.6.1.4.1.20632.2.55
hourlyEncrypted
in the past hour.
1.3.6.1.4.1.20632.2.56
totalRedirected
Number of messages redirected to another
mail server since last system reset.
1.3.6.1.4.1.20632.2.57
dailyRedirected
mail server in the past 24 hours.
1.3.6.1.4.1.20632.2.58
hourlyRedirected
mail server in the past hour.
1.3.6.1.4.1.20632.2.59
totalSent
Number of outbound messages delivered to
the intended recipient, without modification,
1.3.6.1.4.1.20632.2.50
totalOutboundQuarantined
Number of outbound messages quarantined
1.3.6.1.4.1.20632.2.60
dailySent
199
1.3.6.1.4.1.20632.2.61
hourlySent
in the past hour.
1.3.6.1.4.1.20632.2.62
domainCount
Number of domains configured on the
system.
The system provides the following traps:
OID
Object
1.3.6.1.4.1.20632.2.1.2
cpuFanDead
1.3.6.1.4.1.20632.2.1.3
sysFanDead
1.3.6.1.4.1.20632.2.1.4
cpuTempHigh
1.3.6.1.4.1.20632.2.1.5
firmwareStorageHigh
1.3.6.1.4.1.20632.2.1.6
mailStorageHigh
1.3.6.1.4.1.20632.2.1.7
raidDegrading
1.3.6.1.4.1.20632.2.1.8
inQueueHigh – "Severity: Alert. In-queue size is high"
1.3.6.1.4.1.20632.2.1.9
outQueueHigh –"Severity: Alert. Out-queue size is high"
1.3.6.1.4.1.20632.2.1.10
notifyQueueHigh
1.3.6.1.4.1.20632.2.1.11
latencyHigh
1.3.6.1.4.1.20632.2.1.12
noMailForTooLong
200
Barracuda Spam Firewall SNMP MIB
Missing the language English in this article! Please add the language, otherwise this article can not be displayed properly.
201
Barracuda Reference MIB
Missing the language English in this article! Please add the language, otherwise this article can not be displayed properly.
202
Using a Syslog Server to Centrally Monitor System Logs
en
Use the ADVANCED > Advanced Networking page to specify a server to which the Barracuda Spam Firewall sends syslog data. Syslog is a
standard UNIX/Linux tool for sending remote system logs and is available on all UNIX/Linux systems. Syslog servers are also available for
Windows platforms from a number of free and premium vendors.
The Web Syslog data contains information about user login activities and any configuration changes made on the machine. This syslog data
appears on the local facility with login information at the info priority level, and configuration changes appear at the debug priority level on the
specified syslog server.
The Mail Syslog captures data related to mail flow and is the same information as that used to build the Message Log in the Barracuda Spam
Firewall. The Mail Syslog includes data such as the connecting IP, envelope 'From' address, envelope 'To' address, and the spam score for the
messages transmitted. This syslog data appears on the mail facility at the debug priority level on the specified syslog server.
See the Syslog section of the ADVANCED > Troubleshooting page for the facility to open a window and view the Mail Syslog or Web Syslog o
utput.
For details about using the Barracuda syslog with the Barracuda Spam Firewall, see Syslog and the Barracuda Spam Firewall.
203
Syslog and the Barracuda Spam Firewall
en
In this article:
en
Information Provided by the Syslog
Configuring the Barracuda Mail Syslog
Parsing the Syslog
Barracuda Syslog Format
Barracuda Action Codes
Barracuda Reason Codes
Information Provided by the Syslog
The Barracuda Spam Firewall generates syslog messages as a means of logging both changes to the Web interface configuration and what
happens to each message as it is processed. The syslog messages are stored in text file format on the Barracuda Spam Firewall and can be sent
to a remote server configurable by the administrator. There are two syslog outputs you can monitor: the Mail syslog and the Web syslog.
The Web syslog contains information about user login activities and any configuration changes made to the Barracuda Spam Firewall Web
interface. User activity data appears on the local facility with login information at the info priority level, and configuration changes appear at the de
bug priority level on the specified syslog server. See the Syslog section of the ADVANCED > Troubleshooting page for the facility to open a
browser window and view the Web syslog output. Since Web syslog messages do not use any special formatting, Web syslog is not covered in
this guide.
The Mail syslog logs what happens to each message as it is processed and is presented in a raw data format that includes reason codes relative
to the message process. This guide will help you understand, parse, and utilize the mail syslog messages and reason codes generated by the
Configuring the Barracuda Mail Syslog
To configure the Mail syslog, using the Barracuda Spam Firewall Web interface, navigate to the ADVANCED > Advanced Networking page and
enter the IP address and port of the syslog server to which syslog data related to mail flow should be sent. You can also specify the protocol, TCP
or UDP, over which syslog data should be transmitted. TCP is recommended.
Syslog data is the same information as that used to build the Message Log in the Barracuda Spam Firewall and includes data such as the
connecting IP Address, envelope 'From' address, envelope 'To' address, and the spam score for the messages transmitted. This syslog data
appears on the mail facility at the debug priority level on the specified syslog server. As the Barracuda Spam Firewall uses the syslog messages
internally for its own message logging, it is not possible to change the facility or the priority level. See the Syslog section of the ADVANCED >
Troubleshooting page in the Barracuda Spam Firewall Web interface to open a window and view the Mail syslog output.
If you are running syslog on a UNIX machine, be sure to start the syslog daemon process with the “-r” option so that it can receive messages
from sources other than itself. Windows users will have to install a separate program to utilize syslog since the Windows OS doesn’t include
syslog capability. Kiwi Syslog is a popular solution, but there are many others are available to choose from, both free and commercial.
Syslog messages are sent via either TCP or UDP to the standard syslog port of 514. If there are any firewalls between the Barracuda Spam
Firewall and the server receiving the syslog messages, make sure that port 514 is open on the firewalls.
Parsing the Syslog
The format of the Barracuda Spam Firewall syslog output is detailed below. For a programmer's guide to parsing the syslog, see How to Parse
the Barracuda Spam Firewall Syslog.
Barracuda Syslog Format
The Barracuda Spam Firewall sends syslog messages in the following format. Whenever an action is taken on a message, it is logged with the
syslog. A message sent to multiple recipients will be logged separately for each recipient. Please be aware that the various syslog
implementations may not display the messages in this exact format. However, the sections should still be present in the syslog lines as shown in
the table below. The following represents the main part of the syslog line:
Each section of the syslog line is defined in the table below.
Syslog Section
Description
204
Timestamp
The time that the syslog message was logged. For reporting
purposes, this section of the syslog line can be ignored. It is useful
when analyzing the logs by hand, but is not needed for compiling
reports. NOTE: In version 5.1.3.007, the Year was appended to the
end of the Timestamp field.
Host
Indicates the host that generated the syslog message. Useful if you
have multiple Barracuda appliances and need to know which host
sent the message.
Barracuda Process
Indicates the process that the email message was in when the syslog
message was generated. Possibilities are: inbound/pass1 …
inbound/pass2 … scan … outbound/smtp. NOTE: In version
6.0.2.002, the 5 digit Process ID ([27564] in the example above) was
removed.
Barracuda Message ID
The most important piece of the syslog entry. This ID is used to
uniquely identify a message. The ID may occur in one of two formats
(a different format is used for the inbound process and for the scan
process). For example, this ID 1126226282-27564-2-0 is used for
RECV transactions and it means the following:
1126226282 = UNIX timestamp
27564-2= Internal Process ID
0 = Message number in SMTP session – this number indicates how
many messages have been sent in that single SMTP session
Start
The start time of the message in UNIX timestamp format, indicating
when the sender began giving us the “From” information for the
message.
End
The end time of the message in UNIX timestamp format, indicating
when the sending server terminated sending of the message.
Service
The service that produced the message. The following services are
available:
RECV – This service indicates a message was handled by the
MTA and processing stopped.
SCAN – This service indicates the message was scanned and
processing may have stopped or it may have been sent to the
outbound processing for delivery.
SEND – This service indicates status of outbound delivery. It is
the only message that may appear multiple times for a given
message ID since delivery may initially have been deferred
before succeeding later on.
205
This section contains the actual information about what happened to
a given message. It is dependent on the service that sent the
information, and the following formats are used:
Info
RECV – Sender Recipient Action Reason ReasonExtra
SCAN – Encrypted Sender Recipient Score Action
Reason ReasonExtra SZ "SUBJ:"Subject
Note that if TLS is used, then 'ENC' will be displayed before the
SZ: entry; if TLS is not USED, there will be a '–' before the SZ:
entry.
SEND – Encrypted Action QueueID Response
The possible fields have the following meanings:
Sender – The address of the sender, if available, and '–' if the
SENDER is blank.
Recipient – The address of the recipient if available and, ‘-‘ if
not available.
Action – The action code indicating what action was taken for
the message. For the “SEND” service these action codes have
different meanings.
Reason – The reason code indicating the reason for the taken
action.
ReasonExtra – Extra information about a given reason (e.g. the
RBL or the body filter that matched in the message).
Encrypted – Indicates whether or not the message was
received or sent encrypted.
Score – The score given to the message if the scoring
mechanism was run.
Subject – The subject of the message if it was available.
QueueID – The queue ID of the message on the Barracuda as
delivery is being attempted.
Response – The response given back by the mail server if
available.
Barracuda Action Codes
RECV and SCAN Services
ID
Meaning
0
Allowed Message
1
Aborted Message
2
Blocked Message
3
Quarantined Message
4
Tagged Message
5
Deferred Message
6
Per-User Quarantined
Message
7
Whitelisted Message
8
Encrypted Message
9
Redirected Message
10
Attachments Stubbed*
* Applies to version 6.0 and higher
SEND Service
ID
Meaning
1
Delivered Message
2
Rejected Message
3
Deferred Message
4
Expired Message
206
Barracuda Reason Codes
RECV and SCAN Services
ID
Meaning
1
Virus
2
Banned Attachment
3
RBL Match
4
Rate Control
5
Too Many Message In Session
6
Timeout Exceeded
7
No Such Domain
8
No Such User
9
Subject Filter Match
11
Client IP
12
Recipient Address
13
No Valid Recipients
14
Domain Not Found
15
Sender Address
17
Need Fully Qualified Recipient
18
Need Fully Qualified Sender
19
Unsupported Command
20
MAIL FROM Syntax Error
21
Bad Address Syntax
22
RCPT TO Syntax Error
23
Send EHLO/HELO First
24
Need MAIL Command
25
Nested MAIL Command
27
EHLO/HELO Syntax Error
30
Mail Protocol Violation
31
Score
34
Header Filter Match
35
Sender Block/Accept
36
Recipient Block/Accept
37
Body Filter Match
38
Message Size Bypass
39
Intention Analysis Match
207
40
SPF/Caller-ID
41
Client Host Rejected
44
Authentication Not Enabled
45
Allowed Message Size Exceeded
46
Too Many Recipients
47
Need RCPT Command
48
DATA Syntax Error
49
Internal Error
50
Too Many Hops
51
Mail Protocol Error
55
Invalid Parameter Syntax
56
STARTTLS Syntax Error
57
TLS Already Active
58
Too Many Errors
59
Need STARTTLS First
60
Spam Fingerprint Found
61
Barracuda Reputation Whitelist
62
Barracuda Reputation Blocklist
63
DomainKeys
64
Recipient Verification Unavailable
65
Realtime Intent
66
Client Reverse DNS
67
Email Registry
68
Invalid Bounce
69
Intent - Adult
70
Intent - Political
71
Multi-Level Intent
72
Attachment Limit Exceeded
73
System Busy
74
BRTS Intent
75
Per Domain Recipient
76
Per Domain Sender
77
Per Domain Client IP
78
Sender Spoofed
79
Attachment Content
80
Outlook Add-in
82
Barracuda IP/Domain Reputation
83
Authentication Failure
208
85
Attachment Size*
86
Virus detected by Extended Malware Protection **
87
Extended Malware Protection engine is busy **
88
A message was categorized for a type of spam **
* Applies to version 6.0 and higher
** Applies to version 6.1 and higher
209
How to Parse the Barracuda Spam Firewall Syslog
For Programmers: Parsing the Barracuda Syslog
For general information about using the Barracuda Spam Firewall syslog, see Syslog and the Barracuda Spam Firewall.
Syslog messages generated by the Barracuda Spam Firewall can be parsed for reporting purposes or for building of a custom message log. It is
easiest to think of each syslog line in terms of the main components, and the INFO portion can then be parsed based on that service.
The following Perl code illustrates a simple parsing of the log lines. It takes a line and places the resulting message information into a hash –
pushing that hash onto a global array of messages when it completes.
sub parse_log_line
{
# Grab the line we were given and create a new message hash for our message
my($line) = @_;
my %message = ();
# These are the components we may have parsed out of the message based on the service
my ($ip, $id, $start_time, $end_time, $name, $info, $domain);
my ($enc, $sender, $recip, $score, $action, $reason, $reason_extra, $subject);
# Grab the main components from the line (IP, MSG_ID, START_TIME, END_TIME, SERVICE, INFO)
#
#
# NOTE: If this is for the SEND log line then the IP, as well as the START/END times are
# bogus values of 127.0.0.1 and 0/0 respectively
if( $line =~ /\s+:\s+([^\s]+) ([^\s]+) (\d+) (\d+) (RECV|SCAN|SEND) (.*)$/)
{
# Grab the main pieces of the log entry and the process specific info
($ip, $id, $start_time, $end_time, $name, $info) = ($1, $2, $3, $4, $5, $6);
# Set the connecting IP, message-id, start-time, and end-time if this wasn't
# for the SEND service
if( $name !~ /SEND/ )
{
$message{client} = $ip;
$message{id} = $id;
$message{start_time} = $start_time;
$message{end_time} = $end_time;
}
# Break out the process specific pieces from the info portion
if( $name =~ /RECV/ )
{
210
# Break the MTA info up into sender/recip/action/reason/reason_extra
if( $info =~ /([^\s]+)\s([^\s]+)\s(\d+)\s(\d+)\s(.*)$/ )
{
($sender, $recip, $action, $reason, $reason_extra) = ($1, $2, $3, $4, $5);
# Store the readable time of this message based on when it was started by
# converting the unix time to its components and then sprintf’ing into readable form
my ($sec,$min,$hour,$mday,$mon,$year,$wday,$yday,$isdst) = localtime($start_time);
$message{time} = sprintf("%02d/%02d/%02d %02d:%02d:%02d", $mon+1, $mday, $year-100, $hour,
$min, $sec);
# Store the sender if we had one
if( $sender ne '-' )
{
$message{from} = $sender;
}
# Store the recipient if we had one
if( $recip ne '-' )
{
$message{mailto} = $recip;
}
# Set our action/reason codes
$message{action_id} = $action;
$message{reason_id} = $reason;
# Pull in the reason_extra field. This should never be anything other
# than ASCII since the mta doesn't have any multi-byte functionality
# ... thus we don't need to eval it.
if( $reason_extra ne '-' )
{
$message{reason_extra} = " ($reason_extra)";
}
}
}
elsif( $name =~ /SCAN/ )
{
# Break the scanner info up into
encrypted/sender/recip/score/action/reason/reason_extra/subject
if( $info =~ /([^\s]+)\s([^\s]+)\s([^\s]+)\s([-\.\d+]+)\s(\d+)\s(\d+)\s(.*)\sSUBJ:(.*)$/ )
211
{
($enc, $sender, $recip, $score, $action, $reason, $reason_extra, $subject) =
($1, $2, $3, $4, $5, $6, $7, $8);
# Store the readable time of this message based on when it was started by
# converting the unix time to its components and then sprintf’ing into readable form
my ($sec,$min,$hour,$mday,$mon,$year,$wday,$yday,$isdst) = localtime($start_time);
$message{time} = sprintf("%02d/%02d/%02d %02d:%02d:%02d", $mon+1, $mday, $year-100, $hour,
$min, $sec);
# Store the sender if we had one
if( $sender ne '-' )
{
$message{from} = $sender;
}
# Store the recipient if we had one and build the msg_file path
if( $recip ne '-' )
{
$message{mailto} = $recip;
}
# Set the subject line
if( $subject )
{
eval
{
# Note: if this is encoded you may want to decode it here and that
# is why this section is in an eval – since nothing guarantees the
# sender encoded the subject properly.
$message{subject} = decode( $subject );
};
}
# Set the score if we had one
if( $score ne '-' )
{
$message{spam_score} = $score;
212
}
# Set our action/reason codes
$message{action_id} = $action;
$message{reason_id} = $reason;
# Pull in the reason_extra field. This has the extra info the filter that matched
# and other things that might be multi-byte so it should probably be eval’d
eval
{
if( $reason_extra ne '-' )
{
$message{reason_extra} = decode( $reason_extra );
}
}
}
}
elsif( $name =~ /SEND/ )
{
# Break the Outbound MTA info up into encrypted/action/queue_id/response
if( $info =~ /([^\s]+)\s(\d+)\s([^\s]+)\s(.*)$/ )
{
my ($enc, $action, $queue_id, $reason) = ($1, $2, $3, $4);
# Do whatever you would like with the delivery transactions – just keep in
# mind that a single message may have multiple outbound entries because of
# being deferred by the downstream server.
}
}
# Put a ref to this message onto our array of messages so we can use it later
push(@message_list, \%message);
# Send back whatever info you would like to the caller here. In this case
# we are sending back the end time as an example that could handle tracking
# last seen message time or something similar
return( $end_time );
}
# No message info to send back
213
return undef;
}
For questions after reading this document, please call Barracuda Networks at 1-408-342-5400, or, if you are in the United States, (888)
Anti-Spam, or (888) 268-4772. You can also Contact Barracuda Networks Technical Support.
en
214
How to Set Up Barracuda Cloud Control
en
Barracuda Cloud Control enables administrators to manage, monitor and configure multiple Barracuda Spam Firewalls (version 5.0 and higher) at
one time from one console. If you are using the Cloud Protection Layer feature of the Barracuda Spam Firewall, you will manage it using the
Barracuda Cloud Control (see Cloud-Based Protection for details). For information specific to the Barracuda Cloud Control product configuration
and management, see the Barracuda Cloud Control Overview.
The same tabbed pages are available on the Barracuda Cloud Control for managing all aspects of your Barracuda Spam Firewall configuration
that you see in each individual web interface, and you can create aggregated reports for multiple Barracuda Spam Firewalls from the Barracuda
Cloud Control console. You can connect one or more Barracuda Spam Firewalls to the Barracuda Cloud Control by doing the following:
1. If you don't already have an account with Barracuda Networks, click the Create a New Barracuda Cloud Control Account link on the A
DVANCED > Cloud Control page.
2. Fill in the required information in the popup window to create the account and click Save Changes. Once the changes are saved, you'll
receive a confirmation email in the email account you listed. Respond to the email to complete the new account setup.
3. Log into your Barracuda Spam Firewall as the administrator. From the ADVANCED > Firmware Upgrade page, check to make sure you
have the latest firmware installed. If not, download and install it now.
4. From the ADVANCED > Cloud Control page, select Yes, enter the Barracuda Networks username and password and click Save
Changes to connect to Barracuda Cloud Control. Note that your Barracuda Spam Firewall can connect with only one Barracuda Cloud
Control account at a time.
5. Log into Barracuda Cloud Control with your username and password and you will see your Barracuda Spam Firewall statistics displayed
on the BASIC > Dashboard page. To access the web interface of your Barracuda Spam Firewall, click on the link in the Products colum
n in the Cloud Control pane on the left side of the page. Or you can click on the product name in the Product column of the Unit Health
pane on the right side of the page.
6. Follow steps 3 and 4 to connect every subsequent Barracuda Spam Firewall to the Barracuda Cloud Control.
7. To stop the synchronization between your Barracuda Spam Firewall and the Barracuda Cloud Control, from the ADVANCED > Cloud
Control page on the Barracuda Spam Firewall, enter the Barracuda Cloud Control username and password for the particular account
associated with that device and click No for Connect to Barracuda Cloud Control. Do this when you know that there will be a loss of
connectivity between the Barracuda Spam Firewall and the Barracuda Cloud Control due to the appliance being physically moved or
other network connectivity issues.
Note that reports cannot be emailed from the Barracuda Spam Firewall when using the Barracuda Cloud Control. The Barracuda Cloud Control
Status field indicates whether or not this Barracuda Spam Firewall is connected to Barracuda Cloud Control.
215
Barracuda Spam Firewall Panel Indicators, Ports, and Connectors
en
The illustrations in this article are based on current hardware models, however, models differ based on release date and may change in
the future. If your appliance connections differ from those shown in this article, contact Barracuda Technical Support for additional
information.
In this article:
en
Barracuda Spam Firewall Models 100, 200, 300, and 400
Front Panel Model 100, 200, 300, and 400
Rear Panel Ports and Connectors Models 100 and 200
Rear Panel Ports and Connectors Model 300
Barracuda Spam Firewall Model 600
Front Panel Model 600
Rear Panel Port and Connectors Model 600
Barracuda Spam Firewall Models 800, 900, and 1000
Front Panel Models 800, 900, and 1000
Rear Panel Port and Connectors Models 800, 900, and 1000
Barracuda Spam Firewall Models 100, 200, 300, and 400
Front Panel Model 100, 200, 300, and 400
The following figure illustrates the Barracuda Spam Firewall power and disk activity indicator lights for models 100, 200, 300, and 400:
The following table describes the Barracuda Spam Firewall power and disk activity indicator lights for models 100, 200, 300, and 400:
Component Name
Description
Power Button
Push to power on the Barracuda Spam Firewall, tap to safely reset
Reset Button
Push for five seconds to reset the Barracuda Spam Firewall.
Power Indicator
Displays a solid blue when the system is powered on.
Disk Light
Displays a solid green light and blinks during disk activity.
Rear Panel Ports and Connectors Models 100 and 200
The following figure illustrates the Barracuda Spam Firewall rear panel ports and connectors for models 100 and 200:
The following table describes the Barracuda Spam Firewall models 100 and 200:
Port/Connector Name
Details
Power Supply
Power supply input.
216
Mouse Port
Optional. Mouse port.
Keyboard Port
Optional. PS2 keyboard connection.
VGA Port
Recommended. Video graphics array (VGA) monitor connection.
HDMI Port
Optional. HDMI video connection.
USB Ports (4)
Optional. USB device connection.
Network Port
Network connection.
Microphone
Optional. Microphone line-in connection.
Line In/Line Out Jack
Optional. Audio input/output connections.
The following table describes the Barracuda Spam Firewall model 300:
Port/Connector Name
Details
Power Supply
Power supply input.
Mouse Port
Keyboard Port
USB Ports (4)
Dual Link DVI-D Port
Optional. Digital monitor connection.
VGA Port
Network Port
Network connection.
The following figure illustrates the Barracuda Spam Firewall rear panel ports and connectors for model 400:
Port/Connector Name
Details
Power Supply
Power supply input.
Fan
Fan.
Mouse Port
Keyboard Port
USB Ports (4)
Dual Link DVI-D Port
Optional. Digital monitor connection.
VGA Port
Network Port
217
Network connection.
Barracuda Spam Firewall Model 600
Front Panel Model 600
The following figure illustrates the Barracuda Spam Firewall power and disk activity indicator lights for model 600:
The following table describes the Barracuda Spam Firewall power and disk activity indicator lights for model 600:
Component Name
Description
Reserved
Reserved for future use.
Network Activity (2)
Blinks green to indicate network activity.
Disk Indicator
Power Indicator
Displays a solid green light when the system is powered on.
Reset Button
Push for 5 seconds to reset the Barracuda Spam Firewall.
Power Button
Rear Panel Port and Connectors Model 600
The following figure illustrates the Barracuda Spam Firewall rear panel ports and connectors for model 600:
Port/Connector Name
Details
Power Supply
Power supply input.
Mouse Port
Keyboard Port
USB Ports (2)
Serial Port
Optional. Serial device connection.
VGA Port
Network Ports (2)
Network connection.
Barracuda Spam Firewall Models 800, 900, and 1000
Front Panel Models 800, 900, and 1000
The following figure illustrates the Barracuda Spam Firewall power and disk activity indicator lights for models 800, 900, and 1000:
218
The following table describes the Barracuda Spam Firewall power and disk activity indicator lights for model 800, 900, and 1000:
Component Name
Description
Reserved
Reserved for future use.
Network Activity (2)
Blinks green to indicate network activity.
Disk Indicator
Power Indicator
Displays a solid green light when the system is powered on.
Reset Button
Push for 5 seconds to reset the Barracuda Spam Firewall.
Power Button
Rear Panel Port and Connectors Models 800, 900, and 1000
The following figure illustrates the Barracuda Spam Firewall rear panel ports and connectors for models 800, 900, and 1000:
The following table describes the Barracuda Spam Firewall models 800, 900, and 1000:
Port/Connector Name
Details
Power Supply (2)
Power supply input.
Mouse Port
Keyboard Port
USB Ports (2)
Serial Port
Optional. Serial device connection.
VGA Port
Network Ports (2)
Network connection.
219
Troubleshooting
en
The following diagnostic tools should help you troubleshoot most problems. Please read this article before contacting Barracuda Networks
Technical Support. See also Replacing a Failed System.
In this article:
en
Basic Troubleshooting Tools
Connect to Barracuda Support Servers
Rebooting the System in Recovery Mode
Reboot options
Basic Troubleshooting Tools
The ADVANCED > Troubleshooting page provides a suite of tools that help troubleshoot network connectivity issues that may be impacting the
performance of your Barracuda Spam Firewall.
For example, you can test your Barracuda Spam Firewall’s connection to the Barracuda Networks update servers to make sure that it can
successfully download the latest Energize Update definitions. You can also ping or telnet to other devices from the Barracuda Spam Firewall,
perform dig/NS-lookup, TCP dump and perform a trace route from the Barracuda Spam Firewall to any another system.
Connect to Barracuda Support Servers
In the Support Diagnostics section of the ADVANCED > Troubleshooting page, you can initiate a connection between your Barracuda Spam
Firewall and the Barracuda Networks Technical Support Center which will allow technical support engineers to troubleshoot any issues you may
be experiencing.
Rebooting the System in Recovery Mode
If your Barracuda Spam Firewall experiences a serious issue that impacts its core functionality, you can use diagnostic and recovery tools that
are available from the reboot menu (see below) to return your system to an operational state.
Before you use the diagnostic and recovery tools, do the following:
Use the built-in troubleshooting tools on the ADVANCED > Troubleshooting page to help diagnose the problem.
Perform a system restore from the last known good backup file.
Contact Barracuda Networks Technical Support for additional troubleshooting tips.
As a last resort, you can reboot your Barracuda Spam Firewall and run a memory test or perform a complete system recovery, as described
below.
To perform a system recovery or hardware test:
1. Connect a monitor and keyboard directly to your Barracuda Spam Firewall.
2. Reboot the system by doing one of the following:
- In the web interface: Go to the BASIC > Administration page, navigate to the System Management section, and click Restart.
- At the front panel of the Barracuda Spam Firewall: Press the Power button on the front panel to turn off the system, and then press the
Power button again to turn the system on.
The splash screen displays with the following three boot options:
Barracuda
Recovery
Hardware_Test
3. Use your keyboard to select the desired boot option, and press the Enter key. You must select the boot option within three seconds after
the splash screen appears. If you do not select an option within three seconds, the Barracuda Spam Firewall starts up in Normal mode
(first option). For a description of each boot option, refer to Reboot Options below.
To stop a hardware test, reboot your Barracuda Spam Firewall by pressing the Ctrl-Alt-Del keys.
Reboot options
The table below describes the options available at the reboot menu.
Reboot Options
Description
220
Barracuda
Starts the Barracuda Spam Firewall in the normal (default) mode.
This option is automatically selected if no other option is specified
within the first three seconds of the splash screen appearing.
Recovery
Displays the Recovery Console, where you can select the following
options:
Barracuda Repair (no data loss) – Repairs the file system on
Full Barracuda Recovery (all data lost) – Restores the factory
settings on your Barracuda Spam Firewall and clears out the
configuration information.
Enable remote administration (reverse runnel) – Turns on
reverse tunnel that allows Barracuda Networks Technical
Support to access the system. Another method for enabling
remote administration is to click Establish Connection to
Barracuda Support Center on the ADVANCED
>Troubleshooting page.
Diagnostic memory test – Runs a diagnostic memory test from
the operating system. If problems are reported when running this
option, Barracuda recommends running the Hardware_Test
option next.
Hardware_Test
Performs a thorough memory test that shows most memory related
errors within a two-hour time period. The memory test is performed
outside of the operating system and can take a long time to
complete. Reboot your Barracuda Spam Firewall to stop the
hardware test.
221
Maintenance
en
In this article:
en
Backing up and Restoring Your System
Updating the Firmware on your Barracuda Spam Firewall
Updating the Firmware of Clustered Systems
Updating the Definitions from Energize Updates
Reloading, Restarting, and Shutting Down the System
Bayesian Database Reset
Backing up and Restoring Your System
You should back up your system on a regular basis in case you need to restore this information on a replacement Barracuda Spam Firewall or in
the event that your current system data becomes corrupt. Please see How to Back Up and Restore System Information and make this a part of
your routine maintenance plan.
Updating the Firmware on your Barracuda Spam Firewall
This should be one of the steps the administrator performs in the initial installation of the Barracuda Spam Firewall. Use the ADVANCED >
Firmware Update page to manually update the firmware version of the system or revert to a previous version. The only time you should revert
back to an old firmware version is if you recently downloaded a new version that is causing unexpected problems. In this case, call Barracuda
Networks Technical Support before reverting back to a previous firmware version.
Updating the Firmware of Clustered Systems
If a system is part of a cluster, we recommend changing the system’s Mode in the Clustered Systems section of the ADVANCED > Clustering
page to Standby before you upgrade its firmware, and then repeat this process on each system in the cluster. Once the firmware on each system
has been upgraded, you can then change the mode on each system back to Active.
Changing a clustered system to Standby mode before upgrading prevents a system on a more recent firmware version from trying to synchronize
its configuration with a system on an earlier firmware version. If you have the latest firmware version already installed, the Download Now button
on the ADVANCED > Firmware Update page is disabled.
Applying a new firmware version results in a temporary loss of service. For this reason, you should apply new firmware versions during
non-busy hours. Before upgrading, BE SURE TO TAKE THE Barracuda Spam Firewall OFFLINE. This will ensure that the inbound
mail queue is emptied and all messages are scanned before the upgrade process begins. DO NOT MANUALLY REBOOT YOUR
SYSTEM at any time during an upgrade, unless otherwise instructed by Barracuda Networks Technical Support.
The current firmware version shows in the top section of the page, with the latest General Release version of the firmware shown below in the Fir
mware Download section. To download the latest firmware version, click the Download Now button. The web interface will display download
progress. When the firmware download is complete, click the Apply Now button. The Barracuda Spam Firewall will reboot and you will need to
log in again to the web interface.
Updating the Definitions from Energize Updates
This should be one of the steps the administrator performs in the initial installation of the Barracuda Spam Firewall. The ADVANCED > Energize
Updates page allows you to manually update the Virus, Policy, and Security Definitions used on your Barracuda Spam Firewall or to have them
updated automatically. Barracuda Networks recommends that the Automatic Updates option be set to On for all three types of definitions so that
your Barracuda Spam Firewall receives the latest rules as soon as they are made available by Barracuda Networks.
Important: If you are using the Barracuda Exchange Anti-Virus Add-in with your MS Exchange mail server, make SURE to set the Automatic
Updates option to On in the Virus Definition Updates section of the ADVANCED > Energize Updates page. This is necessary to ensure that
the add-in receives constant updates of virus signatures from the Barracuda Spam Firewall.
Reloading, Restarting, and Shutting Down the System
The System Management/Shutdown section on the BASIC > Administration page allows you to shut down, restart, and reload system
configuration on the Barracuda Spam Firewall. You can also take the system offline if necessary, which is recommended whenever you do a
Firmware Update. A unit in Offline (Maintenance) mode will stop accepting incoming mail until it is put back online.
Shutting down the system powers off the unit. Restarting the system reboots the unit. Reloading the system re-applies the system configuration.
You can also perform a hard reset of the Barracuda Spam Firewall by pressing the RESET button on the front panel of the system. Caution
should be used when pressing the reset button, however, since doing so while the Barracuda Spam Firewall is in the midst of a configuration
222
update or other task can result in inadvertent corruption of the system.
When you press the Reset button, the following actions occur:
Reboots the system
Resets the IP address if held down for 5 seconds or more. Do not press and hold the RESET button for longer than a few seconds –
doing so changes the IP address of the system. Pushing and holding the RESET button for:
5 seconds changes the IP address to the default of 192.168.200.200
8 seconds changes the IP address to 192.168.1.200
12 seconds changes the IP address to 10.1.1.200
Bayesian Database Reset
If you have Use Bayesian set to Yes on the BASIC > Spam Checking page, read this section. For more information about how Bayesian
Analysis works, please see Bayesian Analysis Inbound.
For a global Bayesian database, the administrator should periodically (every 6 months or so) clear it out by resetting it from the BASIC >
Spam Checking page, then, from the BASIC > Message Log page, marking at least 200 messages as either Spam or Not spam using
the buttons on the page. Bayesian filtering will NOT take effect until 200 or more of each spam and not-spam messages are marked as
such.
If per-user Bayesian is enabled (from the USERS > User Features page), each user should reset their own Bayesian database and
follow up with marking 200 or more messages as spam or not spam, either in their quarantine inbox (QUARANTINE > Quarantine Inbox
page) or from their regular email client if they have installed either the MS Outlook add-in or Lotus add-in. For more information about
mail client add-ins, see Barracuda Outlook Add-In Overview 6 and Above and the USERS > User Features page in the web interface.
223
How to Back Up and Restore System Information
en
Three Kinds of Backup Files
The ADVANCED > Backup page lets you back up and restore three kinds of backup files for your Barracuda Spam Firewall:
System configuration
Bayesian databases - global and per-user (if your model supports per-user)
Explicit Users to Accept For and Alias Linking data
You should back up your system on a regular basis in case you need to restore this information on a replacement Barracuda Spam Firewall or in
the event that your current system data becomes corrupt.
To prepare the system for backing up, first configure your backup server information, then select which, if not all, backups you want to create,
and, if desired, a schedule of automated backups on the ADVANCED > Backup page. If you are restoring a backup file on a new Barracuda
Spam Firewall that is not configured, you first need to assign your new system an IP address and DNS information on the BASIC > IP
Configuration page of the new system.
Important notes about backups:
Do not edit backup files. Any configuration changes you want to make need to be done through the Web interface. The configuration
backup file contains a checksum that prevents the file from being uploaded to the system if any changes are made.
You can safely view a backup file in Windows WordPad or TextPad. You should avoid viewing backup files in Windows Notepad
because the file can become corrupted if you save the file from this application.
Information not backed up with the system configuration file includes system password, system IP information, DNS information
and clustering settings. For a complete list of settings that are not backed up, please see the online help of the ADVANCED > Backup p
age.
For Automated Backups, you must select a server type. If you select FTP, note the following. The Barracuda Spam Firewall, by default,
initiates ftp in passive mode. If your backup times out, and your ftp server is running in passive mode, and you have a firewall between
your Barracuda Spam Firewall and your ftp server, you may need to open ports on your firewall to allow passive-mode ftp connections.
The port range depends on your ftp server configuration. Ideally, the firewall should be configured so that only that range of ports is
accessible to the ftp server machine. Make sure that there aren't any other TCP services with port numbers in the port range listening on
the ftp server machine.
Restoring a Backup
Restoring a backup simply requires browsing your local system with the click of a button on the ADVANCED > Backup page and selecting a
backup file. Please see the online help on that page for details about restoring backups.
Do not restore a configuration file onto a machine that is currently part of a cluster. All cluster information will be lost and the units will
need to be re-clustered if this happens.
If you need to restore a backup from one Barracuda Spam Firewall model to a different model, please contact Barracuda Technical
Support before proceeding. Note that settings on one model may not apply to a different model.
224
Replacing a Failed System
en
Replacing a Failed System
Before you replace your Barracuda Spam Firewall, use the tools provided on the ADVANCED > Troubleshooting page to try to resolve the
problem, or call Barracuda Networks Technical Support.
Barracuda Instant Replacement Service
In the event that a Barracuda Spam Firewall fails and you cannot resolve the issue, customers that have purchased the Instant Replacement
service can call Barracuda Networks Technical Support and arrange for a new unit to be shipped out within 24 hours.
After receiving the new system, ship the old Barracuda Spam Firewall back to Barracuda Networks at the address below with an RMA number
marked clearly on the package. Barracuda Networks Technical Support can provide details on the best way to return the unit.
Barracuda Networks
3175 S. Winchester Blvd
Campbell, CA 95008
attn: RMA # <your RMA number>
To set up the new Barracuda Spam Firewall so it has the same configuration as your old failed system, first manually configure the new
system’s IP information on the BASIC > IP Configuration page, and then restore the backup file from the old system onto the new
system. For information on restoring data, refer to How to Back Up and Restore System Information. For information on returned device
management, refer to How Barracuda Networks Manages Returned Device Drives.
Tools and Add-Ins
en
In this Section
Barracuda Spam Firewall API Guide
Barracuda Message Center User's Guide
Barracuda Spam Firewall User 's Guide 6 and Above
Barracuda Spam Firewall User's Guide 5.x
Barracuda Outlook Add-In Overview 6 and Above
Barracuda Outlook Add-In Overview 5.x
Barracuda Spam Firewall Outlook Add-In Deployment Guide 6.1.2 and Above
Barracuda Spam Firewall Outlook Add-In Deployment Guide 5.x
SMTP Error Codes
225
Barracuda Spam Firewall API Guide
en
In this article:
en
How the Barracuda API Works
What Can Be Configured With the APIs
Understanding Variables in the Configuration
Secured Access to the APIs
XML-RPC Model
The XML-RPC Request and Response
Single Value Request / Response
Example: Perl
Multi-Value Response
Error Response
Example – PHP
Example – Java
General APIs
Config.get
Example 1: Get the value of a variable under global scope
Example 2: Get the value of a per-domain setting
Config.get - tied variable examples
Example 1: Get the value of a global tied variable
Config.list
Example 1: List all valid domains
Example 2: List of tied objects - all custom RBLs
Config.set
Example 1: Set the value for a scoped object under global scope
Example 2: Set values for several variables under global scope
Example 3: Set the value of a global tied variable
Config.create
Example 1: Create a scoped object in global scope - a new domain
Example 2: Create a tied object - custom RBL with a custom action
Config.delete
Example 1: Deleting a scoped object
Example 2: Delete a tied object and its tied variable values – global scope
Example 3: Delete a tied object and its tied variable values – domain scope
Config.add
Example – Adding a value to a variable
Config.remove
Example – Removing values from a variable under global scope
Config.reload
Config.varlist
Config.var_attr
Example – List the attributes and their values for global Block level.
APIs for the Barracuda Spam Firewall
User.create
User.list
User.remove
User.update_pref
Domain.add
Domain.delete
Use Case Scenarios
Use Case – Adding a Whitelist Entry to a User Account
Use Case – Adding a Blocklist Entry for a Domain
Use Case – Adding a Regular Expression to a Content Filter
Use Case – Listing Explicit Users (Valid Recipients) and Aliases at the Global Level
Use Case – Adding and Configuring Multiple Domains
Use Case – Listing Valid Recipients and Aliases for a Domain
Use Case – Adding Valid Recipients and Aliases for a Domain
Use Case – Deleting Aliases and Valid Recipients for a Domain
Appendix 1
Error (Fault) Codes
226
227
How the Barracuda API Works
The Barracuda set of APIs provides for remote administration and configuration of the Barracuda Spam Firewall version 4.x and above. Two sets
of APIs are presented in this guide: the General APIs section covers "generic" APIs that may be used with all Barracuda Networks appliances
that support an API, and the APIs for the Barracuda Spam Firewall section covers APIs that are specific only to the Barracuda Spam Firewall.
Most of the examples shown use Perl script.
The framework of the API provides for the programmer to get or set variables inside an XML-RPC request that correspond to field values in the
configuration database in the Barracuda Spam Firewall. Some languages such as Perl, for example, provide wrappers for XML-RPC requests,
providing an interface to form the request.
What Can Be Configured With the APIs
The APIs work through manipulation of variables inside of the system configuration database, and anything that can be declared in that database
can be set or checked with the APIs. This includes most things that you can set by clicking the Save button in the Barracuda Spam Firewall web
interface. For example, from the BASIC > Spam Checking page, you can set global Spam Scoring Limit for the actions Block, Tag or
Quarantine, and then click the Save button:
Conversely, most things that correspond to "action" type buttons in the web interface cannot be configured by the APIs. For example, from the B
ASIC > Administration page, you can click a button to take the system offline, to shut it down or to clear the message log, but you cannot
execute these "actions" via the APIs. An exception to this is the Reload feature/button – there is an API to re-apply the system configuration.
Understanding Variables in the Configuration
The examples included in this guide demonstrate getting and setting some of the variables in the configuration database and include snapshots
of the configuration as it would appear in a backup file of the Barracuda Spam Firewall "system configuration". To view a complete list of variable
names and values in your current configuration, create a System Configuration backup from the ADVANCED > Backup page and view the file
contents in any editor that supports UNIX file format (for instance, use NotePad if you are using Windows).
Some examples use variable names in the method calls, while other examples use explicit values, just to demonstrate both ways of making API
calls.
Important note: Make sure not to use an editor that may add special characters. Also make sure to use single quotes to surround literal values in
your calls, and use double quotes to surround variables. For example:
my $url
= "http://$cuda_ip:80/cgi-mod/api.cgi?password=help";
my $result = $xmlrpc->call ('config.set', { type=>'domain',
path => 'barracuda.com',
mta_relay_advanced_host => '1.3.3.7'
});
Two of the methods in the General APIs section, config.varlist and config.var_attr, are utilities that provide information on scope and attributes of
configuration variables to help you understand how to access and use them. Calling these methods prior to using the other APIs will provide a
good reference of the configuration variables.
Secured Access to the APIs
228
Access to these APIs are limited to IP addresses on a trusted IP address list configured on the BASIC > Administration page in the Allowed
API IP/Range section of the Barracuda Spam Firewall web interface. Make sure to enter the IP address(es) from which you'll access the APIs in
this section of the web interface as the first thing you do. Attempts to call these APIs from any IP address that is not on the list will be denied. All
calls to the APIs require the use of the API password, which is set on the same page and section in the web interface.
XML-RPC Model
In the APIs, action parameters are received as XML strings that comply with the XML-RPC specification, which can be viewed here: http://www.X
MLrpc.com/spec. This requires that requests for all actions be in the form of an HTTP POST request. All actions are rolled into one CGI script (for
example: api.cgi) and map to an XML-RPC method, and the parameters are those needed for the action to complete.
For example, the get action maps to the config.get XML-RPC method and all the parameters needed for the get will be sent in the XML body.
The Perl module XML::RPC (note that this is not a part of the standard Perl distribution) will be used by api.cgi to retrieve the requested method
and parameters. Once this is done, the action is performed and the response is sent back to the client. When an error is detected, a response
that complies with the fault response of the XML-RPC specification is sent (see examples below). This response contains both a fault code and a
meaningful fault string. See Appendix 1 of this guide for a list and explanation of fault codes.
The XML-RPC Request and Response
The XML script is called from a Perl script or other scripting language. Each API takes its own set of parameters which are submitted in the XML
body of the request. Examples of the XML output follow the request example below, both for a successful request as well as for a request that
returns an error. The single-value request / response involves a single variable value. Responses that contain multiple values will send the values
back as an XML-RPC array. The response from the scripts is in the form of XML per the examples shown in this guide.
To make the request, use the base URL of your Barracuda Spam Firewall that you use for connecting to the web interface and append the script
name you wish to use. For example, if your script is called 'api.cgi', your URL might look something like this:
http://barracuda.mydomain.com:8000/cgi-mod/api.cgi
Parameters used to build the request typically include some or all of the following:
variable :: A required parameter that tells the API which variable to return from the configuration. For example, the configuration variable
'scana_block_level' represents the global Spam Scoring Limit block level as set on the BASIC > Spam Checking page in the web
interface. To get or set this variable's value, you'd put 'scana_block_level' in the XML request body specified as a variable:
<name>variable</name>
<value>
<string><![CDATA[scana_block_level]]>
</string>
</value>
password :: A required parameter which the API uses to authenticate access to a page and which is set by the administrator on the BAS
IC > Administration page in the API Password field. See the contents of 'my $url' in the Single Value Request / Response example
below, which uses a password of '1234'.
type :: A parameter that specifies the class/scope of a variable. The "scope" of a variable would be one of either global (for global
settings), domain (for per-domain settings) or user (for per-user settings).
If the variable is a "tied variable", however, one or more other variables are related to it, so multiple variables will be specified in the XML request.
For example, on the BLOCK/ACCEPT > IP Reputation page, a custom RBL domain name or IP address is associated with, or "tied to" an
"action" of Block, Quarantine or Tag. The variable names to set, which you'll see in the configuration file, are mta_rbl_custom_name and
mta_rbl_custom_action respectively. In this case, the "type" would be 'mta_rbl_custom_name'.
path :: A parameter that typically corresponds to scope_data which refers to the particular instance of the object. For variables with
global scope, the path is an empty string because there can be only one instance of global and it is the "starting point" in the same
manner, for example, as the root (/) directory in Unix. So all variable and objects under global scope have type as 'global' and path as an
empty string.
When setting the value of a variable or variables that have a type of 'domain', the path would be expressed as the domain name. When
working with tied variables such as 'httpd_acl_ip_config_address' which relates to a value of 'httpd_acl_ip_config_netmask', for example,
the path would be expressed as the actual IP address corresponding to 'httpd_acl_ip_config_address', as shown in this example:
To get the value of httpd_acl_ip_config_netmask corresponding to the httpd_acl_ip_config_address of 192.168.1.1 , the arguments would be:
type:
httpd_acl_ip_config_address
path:
192.168.1.1
variable: httpd_acl_ip_config_netmask
Single Value Request / Response
229
To determine the Spam Scoring Limit global Block level (set in the web interface on the BASIC > Spam Checking page) for the Barracuda
Spam Firewall, use the config.get method to retrieve the current Block value as shown in this example.
To set the value of the global Block level, call the config.set method and set the variable scana_block_level to the desired value. Both calls deal
with a single value. In the configuration backup file, you'll see this entry for the global Spam Scoring Limit Block level, indicating that the current
setting is '9' on the scale from 0-10:
# Default Block Level
scana_block_level = 9
Example: Perl
The config.get request would look something like this as called from a Perl script. The additional examples in further sections of this guide will
only show the call from a Perl script.
#!/usr/bin/perl
use strict;
use LWP::UserAgent;
use HTTP::Request::Common;
# IP Address of your Barracuda
my $cuda_ip = '192.168.126.98';
my $url = "http://$cuda_ip:80/cgi-mod/api.cgi?password=help" ;
my $ua = new LWP::UserAgent;
my $req = new HTTP::Request 'POST', $url;
my $xml = qq|
Here's the XML:
<?xml version="1.0" encoding="UTF8"?>
<methodCall>
<methodName>config.get</methodName>
<params>
<param>
<value>
<struct>
<member>
<value><string><![CDATA[scana_block_level]]></string>
</value>
</member>
<member>
<name>type</name>
<value><string><![CDATA[global]]></string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
|;
# setup transport object with request object
$req->content_type('text/xml');
$req->content($xml);
# send the request over transport object
my $res = $ua->request($req);
# show the response from the Barracuda
print $res->as_string;
# END
The request is an HTTP POST to the /cgi-mod/api.cgi '. The POST data is an XML body that contains the request method config.get inside the
<methodName> tag. The requested method is config.get since we are trying to retrieve the global Block level.
230
Note that the mandatory parameters needed for completing this action, "variable" (name of the configuration variable) and "password", are
contained inside the <struct> tag. Each parameter is identified by the name (<name> tag) and the value (<value> tag). Possible types for each
parameter are restricted by the types listed in the XML-RPC specification.
This example includes only the mandatory parameters. Optional parameters can be added to the XML body using the format mentioned and will
be processed accordingly. Sample output for the request would look something like this:
HTTP/1.1 200 OK
Connection: close
Date: Thu, 24 Jun 2010 18:41:47 GMT
Server: BarracudaHTTP 2.0
Content-Type: text/xml; charset=UTF-8
Client-Date: Thu, 24 Jun 2010 18:42:08 GMT
Client-Peer: 192.168.126.98:80
Client-Response-Num: 1
Client-Transfer-Encoding: chunked
Here's the XML:
<?xml version="1.0" encoding="UTF-8" ?>
<methodResponse>
<params>
<param>
<value>
<i4>7</i4>
</value>
</param>
</params>
</methodResponse>
All responses will contain the 200 OK success status code. Content-type of the response will be text/XML. The actual response, i.e. the value of
the requested configuration variable, will be sent inside the <value> tag.
Multi-Value Response
Responses that contain multiple values will send the values back as an XML-RPC array. The example below is a request for a list of domains
configured as Accepted Email Recipient Domain(s) on the Barracuda Spam Firewall, which can be set from the BASIC > IP Configuration pa
ge in the web interface and which are stored in the configuration database in the mta_relay_domain variable. Here’s a snapshot of the
configuration file as viewed in Windows NotePad:
mta_relay_domain = domain1.com<cr>domain2.com<cr>domain3.com
# Email Address For Testing
mta_relay_email = [email protected]
# Default Relay Mail Server
mta_relay_host = 10.5.105.115
# Default Relay Mail Server Port
mta_relay_port = 25
The response may include multiple values, returned as an array inside the <array> tag. The format of the XML response body looks like this,
returning three (domain name) values:
231
OK <?XML version="1.0" encoding="UTF8"?>
<methodResponse>
<params>
<param>
<value>
<struct>
<member>
<name>mta_relay_domain</name>
<value>
<array>
<data>
<value>
<string>domain1.com</string>
</value>
<value>
<string>domain2.com</string>
</value>
<value>
<string> domain3.com</string>
</value>
</data>
</array
</value>
</member>
</struct>
</value>
</param>
</params>
</methodResponse>
Error Response
Error responses use the XML-RPC faultCode and faultString formats. The error code will be the value of the faultCode member and the error
string will be the value
of the faultString member. See the Appendix 1 for a list of faultCodes and descriptions of possible errors. Here's an example of an error
response, showing the XML:
OK <?XML version="1.0"?>
<methodResponse>
<fault>
<value>
<struct>
<member>
<name>faultCode</name>
<value><i4>500</4></value>
</member>
<member>
<name>faultString</name>
<value>
<string>No such variable in configuration</string>
</value>
</member>
</struct>
</value>
</fault>
</methodResponse>
Example – PHP
This example calls the user.create API to create a new user account, which is covered in the APIs for the Barracuda Spam Firewall section of
this guide. The library used for this example can be found on the following sourceforge page:
232
http://sourceforge.net/projects/phpxmlrpc/
In the code the library is included as a file. Make sure this file is readable from within your environment.
<?php
include("xmlrpc.inc");
$y = new xmlrpcval(
array(
"user" => new xmlrpcval("[email protected]", "string")
), "struct");
$m = new xmlrpcmsg('user.create');
$m->addParam($y);
$c = new xmlrpc_client("/cgi-mod/api.cgi?password=[APIPassword]", "[BarracudaIP]", [BarracudaPort]);
$r = $c->send($m);
if (!$r->faultCode()) {
$v = $r->value();
print $r->serialize();
} else {
print "Fault <BR>";
print "Code: " . htmlentities($r->faultCode()) . "<BR>" .
"Reason: '" . htmlentities($r->faultString()) . "'<BR>";
}
?>
Example – Java
This example calls the user.create API to create a new user account, which is covered in the APIs for the Barracuda Spam Firewall section of
this guide. In the example, a key value pair is created using a standard Map class and added into a Vector list.
Required: Apache WS XML-RPC:
http://ws.apache.org/xmlrpc/
import org.apache.xmlrpc.client.XmlRpcClient;
import org.apache.xmlrpc.client.XmlRpcClientConfigImpl;
import java.net.URL;
import java.util.Hashtable;
import java.util.Map;
import java.util.Vector;
public class BarracudaAPI {
public static void main(String[] argv) {
try {
XmlRpcClientConfigImpl config = new XmlRpcClientConfigImpl();
config.setServerURL(new URL("http://[BarracudaIP]:[BarracudaPort]/cgi-mod/api.cgi?password=[APIPassword]"));
XmlRpcClient client = new XmlRpcClient();
client.setConfig(config);
// Create key value pair
Map keyVals = new Hashtable();
keyVals.put("user","[email protected]");
// Start building the parameter list
Vector params = new Vector();
// Add key parameter
params.add( keyVals );
Object result = client.execute("user.create", params);
System.out.println(result);
} catch( Exception ex) {
ex.printStackTrace();
}
}
}
General APIs
The API interfaces presented in this section are general in that they are applicable to the Barracuda Spam Firewall as well as to other Barracuda
Networks appliances. The examples presented here are specific to the Barracuda Spam Firewall.
Config.get
233
Use this method to retrieve values of variables in the system configuration. If the variable requested has only a single value (Spam Tag
Configuration Subject Tag level, for example), the output will be different than the output for a variable that contains a list (users, domains, etc.).
This method gets the value of the variable in the object of $type named $path. The return $value is a reference to an array if it is multi-valued, i.e.
a list.
Refer to the example in Single Value Response above for getting a variable with a single value and to Multi-value Response above for getting
a variable that contains a list. Arguments to the method can be specified by just adding the parameter in the XML request.
Parameters Allowed : The following variables are used with the config.get method. These variables should be provided as part of the request
XML in the HTTP POST request.
variable :: A required parameter that tells the API which variable to return.
password :: A required parameter which the API uses to authenticate access to a page and which is set by your administrator.
type :: A required parameter that specifies the class/scope of a variable.
path :: A required parameter that is the qualified name of an object for which the value is required. Note that the value for path is an
empty string for getting a variable under global scope.
Example 1: Get the value of a variable under global scope
Get the value of a variable, scana_subject_tag in this case, under global scope. This example will return the Subject Tag string to be inserted by
the Barracuda Spam Firewall in the subject of a message determined to be spam. This setting is configured from the BASIC > Spam Checking p
age for the global setting. Note that the path value is an empty string since the scope, or type, is global.
Arguments:
type: 'global'
path: ''
variable: scana_subject_tag'
Sample Request:
<?XML version="1.0" encoding="UTF8"?>
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<value><string><![CDATA[scana_subject_tag]]></string>
</value>
</member>
<member>
<name>path</name>
<value><string></string>
</value>
</member>
<member>
<name>type</name>
<value>
<string><![CDATA[global]]></string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Response:
234
OK <?XML version="1.0"?>
<methodResponse>
<params>
<param>
<value>
<string><![CDATA[Block]]></string>
</value>
</param>
</params>
</methodResponse>
Example 2: Get the value of a per-domain setting
This example gets the value of the Spam Scoring Limit block level, scana_pd_block_level, for domain thisdomain.net. In the configuration
backup file, this variable is listed like this:
# Domain Spam Block Score
scana_pd_block_level = 5
Arguments:
type: 'domain'
path: 'thisdomain.net'
variable: 'scana_pd_block_level'
Sample Request:
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<value><string><![CDATA[scana_pd_block_level]></string>
</value>
</member>
<member>
<name>path</name>
<value><string><![CDATA[thisdomain.net]]></string>
</value>
</member>
<member>
<name>type</name>
<value>
<string><![CDATA[domain]></string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Response:
235
<methodResponse>
<params>
<param>
<value>
<i4>5</i4>
</value>
</param>
</params>
</methodResponse>
Config.get - tied variable examples
The config.get method can also be used to get the values of variables that are dependent upon, or "tied to" other variables.
This example gets the netmask value, httpd_acl_ip_config_netmask, tied to the Allowed API IP/Range value, httpd_acl_ip_config_address, set
on the BASIC > Administration page. These IP addresses allow access to the Barracuda Spam Firewall via SNMP queries to retrieve error
information or to administer the system via the API. In the request, the IP address is specified in the path. These variables appear in the
configuration backup file like this:
# API/SNMP IP Address List
httpd_acl_ip_config_address = 192.168.1.1
# API/SNMP IP Netmask List
httpd_acl_ip_config_netmask = 255.255.128.0
Arguments:
type:
httpd_acl_ip_config_address
path:
192.168.1.1
variable: httpd_acl_ip_config_netmask
Sample Request:
236
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<value><string> <![CDATA[httpd_acl_ip_config_netmask]]> </string>
</value>
</member>
<member>
<name>path</name>
<value><string>< ![CDATA[global]]> ></string>
</value>
</member>
<member>
<name>type</name>
<value>
<string><![CDATA[domain]]></string>
</value>
</member>
</struct>
</param>
</params>
</methodCall>
Response:
<methodResponse>
<params>
<param>
<value>
<string>![CDATA[255.255.128.0]]</string>
</value>
</param>
</params>
</methodResponse>
This example gets the action (Block, Tag, Quarantine) currently assigned to a custom reputation blocklist (RBL) which can be set from the BLOC
K/ACCEPT > IP Reputation page in the web interface. The call gets the value of the mta_rbl_custom_action variable, which is set to "Block",
corresponding to the mta_rbl_custom_name sbl.spamhaus.org, which is under global scope. These variables appear in the configuration backup
file like this:
# Custom RBL Action List
mta_rbl_custom_action = Block
# Custom RBL List
mta_rbl_custom_name = sbl.spamhaus.org
Arguments:
type: 'mta_rbl_custom_name'
path: 'sbl.spamhaus.org'
variable: 'mta_rbl_custom_action'
Sample Request:
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<value>
<string><![CDATA[mta_rbl_custom_action]]></string>
</value>
</member>
<member>
<name>path</name>
<value>
<string><![CDATA[sbl.spamhaus.org]]></string>
</value>
</member>
<member>
<name>type</name>
<value>
<string><![CDATA[mta_rbl_custom_name]]></string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Response:
237
238
<methodResponse>
<params>
<param>
<value>
</value>
</param>
</params>
</methodResponse>
Config.list
This method lists the children of child_type ('domain', in this case) under the object parent_path of type 'parent_type'.
Parameters Allowed: The following variables are used by the config.list method and should be provided as part of the request XML in the HTTP
POST request.
type :: A required parameter that tells the API about the class/scope of the parent container.
path :: A required parameter that is the qualified name of a parent object. Note that the value for path is an empty string for getting a
variable under global scope.
child_type :: A required parameter that specifies the child class/scope to list.
Example 1: List all valid domains
List all the children of type 'domain' under scope 'global'. This call returns a list of all domains for which the Barracuda Spam Firewall will accept
email, and which can be created and viewed from the DOMAINS page of the web interface. Each instance of the child_type (domain) appears in
the configuration backup file like this:
#scope:<domain>::scope_data: = 'thisdomain.net'
#scope:<domain>::scope_data = 'barracuda.com'
Arguments:
type: 'global'
path: ''
child_type: 'domain'
Sample Request:
<methodCall>
<methodName>config.list</methodName>
<params>
<param>
<value>
<struct>
<member>
<name>child_type</name>
<value>
<string>
<![CDATA[domain]]>
</string>
</value>
</member>
<member>
<name>path</name>
<value>
<string></string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[global]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Response:
239
240
OK <?xml version="1.0" encoding="UTF8"?>
<methodResponse>
<params>
<param>
<value>
<array>
<data>
<value>
<string>
<![CDATA[thisdomain.net]]>
</string>
</value>
<value>
<string>
<![CDATA[barracuda.com]]>
</string>
</value>
</data>
</array>
</value>
</param>
</params>
</methodResponse>
Example 2: List of tied objects - all custom RBLs
This example lists all values for the tied object mta_rbl_custom_name, under global scope. Custom RBLs are created from the web interface on
the BLOCK/ACCEPT > IP Reputation page and have an associated action of Block, Tag or Quarantine. In the configuration backup file, the
three RBLs configured in this example would appear like this:
# Custom RBL List
mta_rbl_custom_name = sbl.spamhaus.org
xbl.spamhaus.org
sbl.org
Arguments:
type: 'global'
path: ''
child_type: 'mta_rbl_custom_name'
Sample Request:
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<value>
<string>
<![CDATA[mta_rbl_custom_name]]>
</string>
</value>
</member>
<member>
<name>path</name>
<value>
<string></string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[global]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Response:
241
242
<methodResponse>
<params>
<param>
<value>
<array>
<data>
<value>
<string>
<![CDATA[sbl.spamhaus.org]]>
</string>
</value>
<value>
<string>
<![CDATA[xbl.spamhaus.org]]>
</string>
</value>
<value>
<string>
<![CDATA[sbl.org]]>
</string>
</value>
</data>
</array>
</value>
</param>
</params>
</methodResponse>
Config.set
Use this method to set the values of variables in the system configuration. This method sets the variables(s) with the given values(s) for the
object of type $type, identified by $path.
Parameters Allowed: The following variables are used by the config.set method and should be provided as part of the request XML in the HTTP
POST request.
type :: A required parameter that specifies the class/scope of an object.
path :: A required parameter that is the qualified name of an object for which the values are to be set.
variable list :: This is a required parameter that tells the API what variables are to be set and the corresponding values.
Example 1: Set the value for a scoped object under global scope
Set the value for a scoped object under global scope. This example sets the value of Spam Score limit block level to '4' for the xyz.com domain.
In the web interface, this value would be set from the BASIC > Spam Checking page after clicking on the Manage Domain link for xyz.com on
the DOMAINS page.
Arguments:
type: 'domain',
path: 'xyz.com'
variable list: scana_pd_block_level = 4
Sample Request:
243
<methodCall>
<methodName>config.set</methodName>
<params>
<param>
<value>
<struct>
<member>
<name>scana_pd_block_level</name>
<value>
<i4>4</i4>
</value>
</member>
<member>
<name>path</name>
<value>
<string>
<![CDATA[xyz.com]]>
</string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[domain]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Response:
244
245
<methodResponse>
<params>
<param>
<value>
<struct>
<member>
<name>Result</name>
<value>
<string>
<![CDATA[200: OK]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodResponse>
Example 2: Set values for several variables under global scope
Set the values of https_port to '443' and mta_rate_control to '40'. The value for Web Interface HTTPS/SSL port can be set on the ADVANCED
> Secure Administration page of the web interface, and the value of Rate Control is set on the BLOCK/ACCEPT > Rate Control page. These
variables appear in the configuration backup file like this (values not yet set):
# HTTPS Web Interface Port
https_port =
# Maximum Connections By IP Per 30 Minutes
mta_rate_control =
Arguments:
type: 'global'
path: ''
variable list: https_port => 443, mta_rate_control => 40
Sample Request:
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<name>https_port</name>
<value>
<i4>443</i4>
</value>
</member>
<member>
<name>mta_rate_control</name>
<value>
<i4>40</i4>
</value>
</member>
<member>
<name>path</name>
<value>
<string></string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[global]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Example 3: Set the value of a global tied variable
246
247
Set the value of httpd_acl_ip_config_netmask to 255.255.128.0 for the httpd_acl_ip_config_address of 192.168.130.222. Note that these
variables are available in the configuration only if you have entered values for Allowed API IP/Range in the BASIC > Administration page, and
would appear in the configuration backup file like this:
# API/SNMP IP Address List
httpd_acl_ip_config_address = 192.168.130.222
# API/SNMP IP Netmask List
httpd_acl_ip_config_netmask =
Arguments:
type: 'httpd_acl_ip_config_address'
path: '192.168.130.222'
variable-value list: httpd_acl_ip_config_netmask =255.255.128.0
Sample Request:
<methodCall>
<methodName>config.set
</methodName>
<params>
<param>
<value>
<struct>
<member>
<name>
httpd_acl_ip_config_netmask
</name>
<value>
<string>
<![CDATA[255.255.128.0]]>
</string>
</value>
</member>
<member>
<name>path</name>
<value>
<string>
<![CDATA[192.168.130.222]]>
</string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[httpd_acl_ip_config_address]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
248
249
Config.create
This method creates an object of a given type and name under the specified parent path. Required variables will be set to their defaults if they
have one; otherwise you must ensure that they have a value before a commit.
Parameters Allowed: The following variables are used by the config.create method and should be provided as part of the request XML in the
HTTP POST request.
parent_type :: A required parameter that tells the API about the class/scope of the parent container.
parent_path :: A required parameter that is the qualified name of a parent object under which a new object will be created.
type :: A required parameter that specifies the child's class/scope to be created.
name :: A required parameter that specifies the name of an object to be created.
variable list :: An optional parameter that tells the API which variable(s) to set in the new object.
Example 1: Create a scoped object in global scope - a new domain
Create a new domain entry of 'xyz.com' under global scope and set the value of variable scana_pd_block_level (per-domain Spam Block level)
to '5'.
Arguments:
parent_type: 'global'
parent_path: ''
type: 'domain'
name: 'xyz.com'
variable list: scana_pd_block_level = '5'
Sample Request:
<methodCall>
<methodName>config.create</methodName>
<params>
<param>
<value>
<struct>
<member>
<name>scana_pd_block_level
</name>
<value>
<i4>5</i4>
</value>
</member>
<member>
<name>parent_type
</name>
<value>
250
<string>
<![CDATA[global]]>
</string>
</value>
</member>
<member>
<name>name</name>
<value>
<string>
<![CDATA[xyz.com]]>
</string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[domain]]>
</string>
</value>
</member>
<member>
<name>parent_path</name>
<value>
<string></string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Example 2: Create a tied object - custom RBL with a custom action
Create a tied object mta_rbl_custom_name of 'spamhaus.org' with an mta_rbl_custom_action of 'Block'. The resulting entries in the
configuration backup file would look something like this:
# Custom RBL List
mta_rbl_custom_name = spamhaus.org
Arguments:
parent_type:'global'
parent_path: ''
name: 'spamhaus.org'
variable list: mta_rbl_custom_action = Block
Sample Request:
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<name>parent_type</name>
<value>
</value>
</member>
<member>
<name>name</name>
<value>
<string><![CDATA[spamhaus.org]]></string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
</string>
</value>
</member>
<member>
<value>
<string></string>
</value>
</member>
251
252
<member>
<name>mta_rbl_custom_action</name>
<value>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Config.delete
This method deletes an object of type $type identified by $path.
Parameters Allowed: The following variables are used by the config.delete method. These variables should be provided as part of the request
type :: A required parameter which specifies the class/scope of an object.
path :: A required parameter which is the qualified name of an object to be deleted.
Example 1: Deleting a scoped object
Delete domain 'xyz.com'.
Arguments:
type: 'domain'
path: 'xyz.com'
variable-value list: httpd_acl_ip_config_netmask = 255.255.128.0
Sample Request:
253
POST /cgi-mod/api.cgi?password=1234 HTTP/1.1
Connection: close
Host: 192.168.3.234:8000
UserAgent:XMLRPC/0.8
ContentLength:357
ContentType:text/xml
<methodCall>
<methodName>config.delete</methodName>
<params>
<param>
<value>
<struct>
<member>
<name>path</name>
<value>
<string><![CDATA[xyz.com]]></string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[domain]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Example 2: Delete a tied object and its tied variable values – global scope
Delete the global tied object mta_rbl_custom_name 'xyz.com' along with all of its tied variables. In this example, the tied variable is
mta_rbl_custom_action, which stores the action (Block, Tag or Quarantine) to take with messages originating from IP addresses in custom
external RBLs. These variables appear in the configuration backup file like this:
# Custom RBL Action List
mta_rbl_custom_action = Block
# Custom RBL List
mta_rbl_custom_name = xyz.com
Arguments:
path: 'xyz.com'
Sample Request:
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<name>path</name>
<value>
<string><![CDATA[xyz.com]]></string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Response:
254
255
<methodResponse>
<params>
<param>
<value>
<struct>
<member>
<name>Result</name>
<value>
<string>
<![CDATA[200: OK]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodResponse>
Example 3: Delete a tied object and its tied variable values – domain scope
Delete the per-domain tied variable mta_sender_allow_address along with its tied variable values. This example deletes the Allowed Email
Address and Domains tied variable values 'test1.com' and 'test2.com' for the domain ‘barracuda.com’.
The tied variable mta_sender_allow_address does not appear in the configuration backup file.
Arguments:
type: 'mta_sender_allow_address'
path: 'barracuda.com'
Sample Request:
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<name>path</name>
<value>
<string><![CDATA[barracuda.com]]></string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[domain]]>
</string>
</value>
</member>
<member>
<value>
<string>
<![CDATA[mta_sender_allow_address]]>
</string>
</value>
</member>
<member>
<name>values</name>
<value>
<array>
<data>
<value>
<string>
<![CDATA[test1.com]]>
</string>
</value>
<value>
<string>
<![CDATA[test2.com]]>
</string>
</value>
</data>
</array>
</value>
</member>
</struct>
</value>
</param>
256
257
</params>
</methodCall>
Config.add
This method adds the given values to the list variable. This method will not add values to tied variables, and a value added must not already exist
in the list. For adding values to tied variables, use the config.create method.
Parameters Allowed: The following parameters are used by the config.add method and should be provided as part of the request XML in the
HTTP POST request.
parent_type :: A required parameter that tells the API about the class/scope of a parent container.
parent_path :: A required parameter which is the qualified name of a parent object
variable :: A required parameter that specifies the variable for which values will be added.
values :: A required parameter specifying a list of values to be added.
Example – Adding a value to a variable
Add values 192.168.128.34 and 192.168.128.2 to the mta_trusted_relay_host list.
Arguments:
parent_type: 'global'
parent_path: ''
variable: 'mta_trusted_relay_host'
values: ['192.168.128.34', '192.168.128.2']
Sample Request:
<methodCall>
<methodName>config.add</methodName>
<params>
<param>
<value>
<struct>
<member>
<value>
<string>
<![CDATA[global]]>
</string>
</value>
</member>
<member>
<value>
<string>
258
<![CDATA[mta_trusted_relay_host]]>
</string>
</value>
</member>
<member>
<name>values</name>
<value>
<array>
<data>
<value>
<string>
<![CDATA[192.168.128.34]]>
</string>
</value>
<value>
<string>
<![CDATA[192.168.128.2]]>
</string>
</value>
</data>
</array>
</value>
</member>
<member>
<value>
<string></string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Config.remove
Use this method to remove the given value(s) from the list variable. This will not remove values from tied variables. For removing values from tied
variables, use the config.delete method.
Parameters Allowed: The following parameters are used by the config.remove method and should be provided as part of the request XML in the
HTTP POST request.
259
parent_type :: A required parameter that tells the API about the class/scope of the parent container.
parent_path :: A required parameter and is the qualified name of a parent object.
variable :: A required parameter that specifies the variable for which values should be removed.
values :: A required parameter specifying a list of values to be removed.
Example – Removing values from a variable under global scope
Removes host/domain name values 'mytrustedrelay1.com' and 'mytrustedrelay2.com from the mta_trusted_relay_host list. These Trusted Relay
Host/Domain names are added or deleted on the ADVANCED > Outbound page in the web interface and represent trusted relays on the
Arguments:
parent_type: 'global',
parent_path: ''
variable: 'mta_trusted_relay_host'
values: ['mytrustedrelay1.com', 'mytrustedrelay2.com']
Sample Request:
<methodCall>
<methodName>config.remove</methodName>
<params>
<param>
<value>
<struct>
<member>
<value>
<string>
<![CDATA[global]]>
</string>
</value>
</member>
<member>
<value>
<string>
<![CDATA[mta_trusted_relay_host]]>
</string>
</value>
</member>
<member>
<name>values</name>
<value>
<array>
<data>
<value>
<string>
<![CDATA[mytrustedrelay1.com]]>
</string>
</value>
<value>
<string>
<![CDATA[mytrustedrelay2.com]]>
</string>
</value>
</data>
</array>
</value>
</member>
<member>
<value>
<string></string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Response:
260
261
<methodResponse>
<params>
<param>
<value>
<struct>
<member>
<name>Result</name>
<value>
<string>
<![CDATA[200: OK]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodResponse>
Config.reload
Use this method to re-apply the system configuration, as can be done with the Reload button on the BASIC > Administration page of the web
interface. The output of a successful call is a simple '200 OK' response - results are shown below.
Parameters Allowed: The following variable is used by the config.reload method.
Sample Request:
262
<methodCall>
<methodName>config.reload</methodName>
<params>
<param>
<value>
<struct>
</struct>
</value>
</param>
</params>
</methodCall>
Config.varlist
Use this method to list all the variables of the configuration and their attributes. This is a good method to call prior to using other APIs so you have
a reference of the configuration variables.
Parameters Allowed: The following variable is used by the config.varlist method.
Sample Request:
<methodCall>
<methodName>config.varlist</methodName>
<params>
<param>
<value>
<struct/>
</value>
</param>
</params>
</methodCall>
Response:
<methodResponse>
<params>
<param>
<value>
<struct>
<member>
<name>new_mta_trusted_relay_netmask</name>
<value>
<struct>
<member>
<name>min</name>
<value>
<string></string>
</value>
</member>
<member>
<name>max</name>
<value>
<string></string>
</value>
</member>
<member>
<name>default</name>
<value>
<string></string>
</value>
</member>
<member>
<name>description</name>
<value>
<string>
<![CDATA[Subnet Mask]]>
</string>
</value>
</member>
<member>
<name>choices</name>
<value>
<array>
<data/>
</array>
</value>
</member>
263
<member>
<name>required</name>
<value>
<i4>1</i4>
</value>
</member>
<member>
<name>class</name>
<value>
<string>
<![CDATA[global]]>
</string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[ip_address]]>
</string>
</value>
</member>
</struct>
</value>
</member>
<member>
<name>mta_outbound_max_queue_lifetime
</name>
<value>
<struct>
<member>
<name>min</name>
<value>
<string></string>
</value>
</member>
<member>
<name>max</name>
<value>
<string></string>
264
</value>
</member>
<member>
<value>
<i4>48</i4>
</value>
</member>
<member>
<value>
<string>
<![CDATA[Outbound Queue Max Message Lifetime(hours):]]>
</string>
</value>
</member>
<member>
<value>
<array>
<data/>
</array>
</value>
</member>
<member>
<value>
<i4>1</i4>
</value>
</member>
<member>
<name>class</name>
<value>
<string>
<![CDATA[global]]>
</string>
</value>
</member>
<member>
<name>type</name>
265
<value>
<string>
<![CDATA[float]]>
</string>
</value>
</member>
</struct>
</value>
</member>
<member>
<name>auth_radius_server</name>
<value>
<struct>
<member>
<name>min</name>
<value>
<string></string>
</value>
</member>
<member>
<name>max</name>
<value>
<string></string>
</value>
</member>
<member>
<value>
<string></string>
</value>
</member>
<member>
<value>
<string></string>
</value>
</member>
<member>
<value>
266
267
<array>
<data/>
</array>
</value>
</member>
<member>
<value>
<string></string>
</value>
</member>
<member>
<name>class</name>
<value>
<string>
<![CDATA[domain]]>
</string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[text]]>
</string>
</value>
</member>
</struct>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodResponse>
Config.var_attr
Use this method to list the attributes of the specified variable.
Parameters Allowed: The following variables should be provided as part of the request XML in the HTTP POST request.
268
variable :: A required parameter that specifies the variable for which attributes are required.
Example – List the attributes and their values for global Block level.
This example lists the attributes of global blocking: min level, max level, current setting, etc. and returns the current value for each attribute.
Sample Request:
<methodCall>
<methodName>config.var_attr</methodName>
<params>
<param>
<value>
<struct>
<member>
<value>
<string>
<![CDATA[scana_block_level]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Response:
<methodResponse>
<params>
<param>
<value>
<struct>
<member>
<name>scana_block_level</name>
<value>
<struct>
<member>
<name>min</name>
<value>
<string></string>
</value>
</member>
<member>
<name>max</name>
<value>
<string></string>
</value>
</member>
<member>
<value>
<i4>7</i4>
</value>
</member>
<member>
<value>
<string>
<![CDATA[Spam Block Level]]>
</string>
</value>
</member>
<member>
<value>
<array>
<data/>
</array>
</value>
</member>
<member>
<value>
<i4>1</i4>
</value>
</member>
<member>
<name>class</name>
269
270
<value>
<string>
<![CDATA[global]]>
</string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[float]]>
</string>
</value>
</member>
</struct>
</value>
</member>
</struct
</value>
</param>
</params>
</methodResponse>
APIs for the Barracuda Spam Firewall
Creating a block of new user accounts or domains, deleting one or more of each, listing user accounts, using Regular Expressions and updating
user-level spam score or quarantine inbox settings are some of the remote configuration capabilities presented here for the Barracuda Spam
Firewall.
User.create
This method creates a user account for the user as specified. The output of a successful call is a simple '200 OK'.
Parameters Allowed: These variables should be provided as part of the request XML in the HTTP POST request.
user :: A required parameter that specifies the user account to be created.
Arguments:
user: [email protected]
Sample Request:
271
<methodCall>
<methodName>user.create</methodName>
<params>
<param>
<value>
<struct>
<member>
<name>user</name>
<value>
<string>
<![CDATA[[email protected]]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
User.list
This method simply lists all the user accounts currently on the system.
Parameters Allowed: The following variable should be provided as part of the request XML in the HTTP POST request.
Sample Request:
<methodCall>
<methodName>user.list</methodName>
<params>
<param>
<value>
<struct/>
</value>
</param>
</params>
</methodCall>
272
Response:
<methodResponse>
<params>
<param>
<value>
<array>
<data>
<value>
<string>
</string>
</value>
<value>
<string>
</string>
</value>
</data>
</array>
</value>
</param>
</params>
</methodResponse>
User.remove
Use this method to remove a user account for the user as specified. The output of a successful call is a simple '200 OK'.
Parameters Allowed: The following variables are used by the user.remove method and should be provided as part of the request XML in the
HTTP POST request:
password:: A required parameter which the API uses to authenticate access to a page and which is set by your administrator.
user :: A required parameter that specifies the user account to be removed.
Arguments:
Sample Request:
?xml version="1.0" encoding="UTF8"?>
<methodCall>
<methodName>user.remove</methodName>
<params>
<param>
<value>
<struct>
<member>
<name>user</name>
<value>
<string>
<![CDATA[test@abcd]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Response:
273
274
<methodResponse>
<params
<param>
<value>
<struct>
<member>
<name>Result</name>
<value>
<string>
<![CDATA[200: OK]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodResponse>
User.update_pref
This method updates the preferences for the user account specified. The output of a successful call is a simple '200 OK'.
Parameters Allowed: The following variables are used by the user.update_pref method. These variables should be provided as part of the
request XML in the HTTP POST request.
user :: A required parameter that specifies the user account whose preference is to be updated.
Note: First, use the config.set method to set the user- specific variables for preferences, then use this method to update the preferences.
Arguments:
Sample Request:
275
<methodCall>
<methodName>user.update_pref</methodName>
<params>
<param>
<value>
<struct>
<member>
<name>user</name>
<value>
<string>
<![CDATA[test@abcd]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Domain.add
Use this method to add a domain, then use the config.set method to configure settings for that domain in a separate call. Use this method in a
loop to add multiple domains. The output of a successful call is a simple '200 OK'.
Parameters Allowed: The following variables are used by the domain.add method. These variables should be provided as part of the request
domain :: A required parameter that specifies the domain to be created.
Arguments:
domain: xyz.com
Sample Request:
276
<methodCall>
<methodName>domain.add</methodName>
<params>
<param>
<value>
<struct>
<member>
<name>domain</name>
<value>
<string>
<![CDATA[xyz.com]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Domain.delete
This method deletes the specified domain. The output of a successful call is a simple '200 OK'.
Parameters Allowed: The following variables are used by the domain.delete method. These variables should be provided as part of the request
domain :: A required parameter that specifies the domain to be deleted.
Arguments:
domain: xyz.com
Sample Request:
277
<methodCall>
<methodName>domain.delete</methodName>
<params>
<param>
<value>
<struct>
<member>
<name>domain</name>
<value>
<string>
<![CDATA[xyz.com]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Use Case Scenarios
These examples draw on the information presented above for using various methods to configure the Barracuda Spam Firewall for common use
cases. Some use cases address domain-level settings and some address global settings.
Use Case – Adding a Whitelist Entry to a User Account
Use the config.add method to add any email senders to the whitelist for a particular user account. This list of senders are not blocked even if the
message matches spam rules. Virus scanning is still applied based on the policy set by the administrator. Whitelisting may be performed by full
email address ("[email protected]") or domain only ("domain.com").
Important: Per-User Quarantine must be enabled for the domain via the web interface BEFORE you attempt to add per-user whitelist entries. To
do so, first, from the DOMAINS > Domain Manager page, click Manage Domain for the particular domain. For example, if the user account is cu
[email protected], click on Manage Domain for barracuda.com. At the domain level, navigate to the BASIC > Quarantine page and set
Quarantine Type to Per-User. Finally, set Enable User Features toYes.
Arguments:
my $value1
= '[email protected]';
my $value2
= '[email protected]';
my $user_account = '[email protected]';
Sample Request:
278
<methodCall>
<methodName>config.add</methodName>
<params>
<param>
<value>
<struct>
<member>
<value>
<string>
<![CDATA[user]]>
</string>
</value>
</member>
<member>
<value>
<string>
<![CDATA[user_scana_sender_allow]]>
</string>
</value>
</member>
<member>
<name>values</name>
<value>
<array>
<data>
<value>
<string>
<![CDATA[$value1]]>
</string>
</value>
<value>
<string>
<![CDATA[$value2]]>
</string>
</value>
</data>
</array>
</value>
</member>
<member>
<value>
<string><![CDATA[$user_account]]></string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Use Case – Adding a Blocklist Entry for a Domain
Use the config.create method to add any IP addresses or networks to the blocklist for a particular domain. This example adds an IP address to
the blocklist for the specified domain and adds values to the per-domain tied variables listed below. The mta_acl_ip_block_action is set to
'quarantine' for mail from the IP address added to the blocklist, and the mta_acl_ip_block_netmask is set to 255.255.255.0 since we're adding
an individual IP address. A comment of 'Blocked IP address' is added as well.
# Add values to per domain tied variable
# Domain – xyz.mydomain.net
# Variable – mta_acl_ip_block_address (domain scope): 10.5.36.59
# Tied variables – mta_acl_ip_block_netmask, mta_acl_ip_block_action, mta_acl_ip_block_comment.
Arguments:
type:
mta_acl_ip_block_address
parent_path:
xyz.mydomain.net
mta_acl_ip_block_netmask: 255.255.255.0
mta_acl_ip_block_action: 'Quarantine'
mta_acl_ip_block_comment: 'Blocked IP Address'
Sample Request:
279
280
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<value>
<string><![CDATA[domain]]></string>
</value>
</member>
<member>
<name>name</name>
<value>
<string><![CDATA[10.5.36.59]]></string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[mta_acl_ip_block_address]]>
</string>
</value>
</member>
<member>
<value>
<string><![CDATA[xyz.mydomain.net]]></string>
</value>
</member>
<member>
<name>mta_acl_ip_block_netmask</name>
<value>
<string><![CDATA[255.255.255.0]]></string>
</value>
</member>
<member>
<name>mta_acl_ip_block_action</name>
<value>
<string><![CDATA[Quarantine]]></string>
</value>
</member>
<member>
<name>mta_acl_ip_block_comment</name>
<value>
<string><![CDATA[Blocked IP address]]></string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Use Case – Adding a Regular Expression to a Content Filter
This example uses the config.create method described in the previous section. Using config.create you can add regular expressions to a content
filter, which is a global setting. For more details about using regular expressions and content filtering, see the BLOCK/ACCEPT > Content
Filtering page. The output of a successful call is a simple '200 OK'.
Arguments:
Regular Expression: \bvi.gra\b (see Regular Expressions)
Sample Request:
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<value>
</value>
</member>
<member>
<name>name</name>
<value>
<string><![CDATA[\\bvi.gra\\b]]></string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[filter_header_list]]>
</string>
</value>
</member>
<member>
<value>
<string></string>
</value>
</member>
<member>
<name>filter_header_list_comment</name>
<value>
<string><![CDATA[Filter this content]]></string>
</value>
</member>
<member>
<name>inbound_filter_header_list_action</name>
<value>
</value>
</member>
<member>
<name>outbound_filter_header_list_action</name>
<value>
<string><![CDATA[Quarantine]]></string>
</value>
</member>
<member>
<name>apply_to_subject</name>
<value>
<string><![CDATA[1]]></string>
</value>
</member>
<member>
<name>apply_to_header</name>
<value>
</value>
</member>
<member>
281
<name>apply_to_body</name>
<value>
</value>
</member>
</struct>
</value>
282
283
</param>
</params>
</methodCall>
Use Case – Listing Explicit Users (Valid Recipients) and Aliases at the Global Level
Supported by firmware version 5.1.3.006, 6.x and higher
Use the config.list method to list valid recipients and aliased accounts at the global level - i.e. not domain-specific. Explicit Users and aliased
email accounts are added or deleted on the ADVANCED > Explicit Users page of the web interface. In this case, the Type, or scope, is blank
(empty) to indicate global. Note that the ‘variable’ ‘list_valid_recipient_aliases’ is not actually a variable as defined in the configuration; rather, it is
an indicator to the API of what is being listed by the config.list call.
Sample Request:
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<value>
<string>
<![CDATA[list_valid_recipient_aliases]]>
</string>
</value>
</member>
<member>
<value>
<string>
<![CDATA[global]]>
</string>
</value>
</member>
<member>
<name>path</name>
<value>
<string>
</string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA['']]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Use Case – Adding and Configuring Multiple Domains
Use the domain.add method, described in the previous section, in a loop to add multiple domains for which the Barracuda Spam Firewall should
process email. These domains will then be listed in the DOMAINS > Domain Manager page of the web interface.
284
To configure the domains, use the config.set method for each domain. This example configures the 'Spam Score limit block level' to 4 for n
domains, by setting the scana_pd_block_level variable, if you put the request in a loop. In the web interface, you'll see this value on the BASIC >
Spam Checking page after clicking on the Manage Domain link for each domain.
Sample Request (for each domain):
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<name>scana_pd_block_level</name>
<value>
<i4>4</i4>
</value>
</member>
<member>
<name>path</name>
<value>
<string>
<![CDATA[$domain]]>
</string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[domain]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Use Case – Listing Valid Recipients and Aliases for a Domain
Use the config.list method to list valid recipients and aliased accounts for a domain. Valid Recipients and aliased email accounts are added or
deleted on the per-domain USERS > Valid Recipients page of the web interface. In this case, the Type, or scope, is ‘domain’, and this call
returns a list of all valid recipients and aliased email accounts for the domain ‘mymail.net’. Note that the ‘variable’ ‘list_valid_recipient_aliases’ is
not actually a variable as defined in the configuration; rather, it is an indicator to the API of what is being listed by the config.list call.
Sample Request:
285
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<value>
<string>
<![CDATA[list_valid_recipient_aliases]]>
</string>
</value>
</member>
<member>
<value>
<string>
<![CDATA[global]]>
</string>
</value>
</member>
<member>
<name>path</name>
<value>
<string> <![CDATA[mymail.net]]>
</string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[domain]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Use Case – Adding Valid Recipients and Aliases for a Domain
Use the config.set method to add valid recipients and aliases for a domain. This case adds a primary account and two email aliases for the
domain ‘testqa.com'. Aliased accounts are added or deleted on the per-domain USERS > Valid Recipients page of the web interface and are
linked to a 'primary account', which receives quarantined mail for the aliased accounts. The primary valid recipient is added first, followed by a
number of aliases. See the per-domain USERS > Valid Recipients page of the web interface for details about alias linking.
Note that the ‘member’ name ‘new_valid_recipient_aliases’ is an indicator to the API of what is being set by the config.set call. Make sure the
domain is present in the Barracuda Spam Firewall before adding recipients and aliases.
Arguments:
path: testqa.com
type: domain
child_type: global
my $domain = "testqa.com";
my $primary_valid_recip = '[email protected]';
my $alias = '[email protected]'.' '.'[email protected]';
my $primary_and_alias = $primary_valid_recip." ".$alias;
286
new_valid_recipient_aliases = '[email protected] [email protected] [email protected]';
Sample Request:
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<name>new_valid_recipient_aliases</name>
<value>
<string>$primary_and_alias</string>
</value>
</member>
<member>
<name>path</name>
<value>
<string>
<![CDATA[$domain]]>
</string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[domain]]>
</string>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Use Case – Deleting Aliases and Valid Recipients for a Domain
Use the config.delete method to delete valid recipients and aliases for a domain.This example deletes the valid recipient and aliases for the
domain ‘testqa.com’. Valid recipients and aliased accounts are added or deleted on the per-domain USERS > Valid Recipients page of the web
interface. Note that the variable ‘delete_valid_recipient_aliases’ is not actually a variable as defined in the configuration; rather, it is an indicator to
the API of what is being deleted by the config.delete call.
In this example, '[email protected]', '[email protected]' are the aliases to be deleted. Make sure the domain for which you are deleting aliased
accounts is present in the Barracuda Spam Firewall. The list of per-domain aliased user accounts to be deleted can be specified in the 'Values'
variable in the XML request.
Arguments:
path: testqa.com
type: domain
my $domain = "testqa.com";
my $user2 = '[email protected]';
my $user3 = '[email protected]';
Sample Request:
287
<methodCall>
<params>
<param>
<value>
<struct>
<member>
<name>path</name>
<value>
<string>
<![CDATA[$domain]]>
</string>
</value>
</member>
<member>
<name>type</name>
<value>
<string>
<![CDATA[domain]]>
</string>
</value>
</member>
<member>
<value>
<string>
<![CDATA[delete_valid_recipient_aliases]]>
</string>
</value>
</member>
<member>
<name>values</name>
<value>
<array>
<data>
<value>
<string>
<![CDATA[$user2]]>
</string>
</value>
<value>
<string>
<![CDATA[$user3]]>
</string>
</value>
</data>
</array>
</value>
</member>
</struct>
</value>
</param>
</params>
</methodCall>
Appendix 1
See the Error Response format under The XML-RPC Request and Response above for an example of how the faultCodes (error codes),
shown below, will be returned with the XML response.
Error (Fault) Codes
Fault Code
400
Description
Example Fault Strings
Required arguments are missing
Too few arguments: <error message>
288
401
Machine does not have access rights
Your machine does not have access rights to
administer...
402
Domain name error
Domain <domain name> already exists
Domain <domain name> is not a valid
domain
403
Access error
Access denied <error message>
406
API was called with incorrect parameters
Incorrect parameters for API call
411
Account error
User account does not exist
412
Account error
User account already exists
421
Account error
Unable to validate account
425
Input object or variable is not valid
Config: Error: Invalid variable: <variable
name used in api> Config: Error: variable
<variable name used in api> not
recognized
Config: Error: Invalid object type: <variable
name used in api>
Config: Error: <variable name used in api> is
not tied to <parent type>
Config: Error: <variable name used in api>
does not belong to any
class
Config: Error: <variable name used in api>
does not belong to <parent
type>
Config: Error: <variable name used in api> is
not of type <parent type>
426
Invalid operation
Config: Error: invalid operation for variable
<variable name used in api>
Config: Error: Cannot add values to tied
variable <variable name used in api>
Config: Error: Cannot remove values from
tied variable <variable name used in api>
427
The object does not exist in the database
Config: Error: Could not find tied object:
<parent type>, <parent path> [<parent
type>]
Config: Error: Could not find scoped object:
<parent type>, <parent path> [global]
Config: Error: Could not find scoped object:
<parent type>, <parent path> [<old parent
type>, <old parent path>]
428
Input value being set is not valid
Config: Error: Could not find values to delete
in <parent path>: <list of invalid values>
429
Required variable is missing
Variable required to create object of type
<parent type>
450
The method you used is unknown
Unknown method called <API method>
499
Unknown error
An unknown error has occurred
500
Unknown error
An unknown error has occurred
} catch( Exception ex) {
289
290
Barracuda Message Center User's Guide
en
This article applies to messages encrypted by the Barracuda Spam Firewall or the Barracuda Email Security Service.
In this article:
en
Receiving an Encrypted Email Message
Logging into the Barracuda Message Center
Picking Up Your Secure Email Message
View messages
Reply to messages
Saving Message Content
Delete multiple messages
Receiving an Encrypted Email Message
If you have received one or more encrypted email messages via the Barracuda Message Center, the sender of the encrypted message(s)
intended to secure the contents of message such that only you, the recipient, can view the body of the message. The subject of the email
notifying you that you've received an encrypted message will look something like this:
You have received an encrypted message from
<mailbox name>@<yourdomain>.com
(or .net, .edu, .org,
etc.). The sender intended for the message contents to be secured by using the Barracuda Email Encryption
Service. You can retrieve the message from the Barracuda Networks Message Center. To view your secure
message, visit the following URL in your browser: <URL> The secure message will expire in 30 days. If you
are unsure of why you received the encrypted message, you can contact the sender before proceeding.
Logging into the Barracuda Message Center
Once you paste the URL into your browser, a Barracuda Networks Message Center page should appear.
1. The first time this system is used, you will be asked to create a password. This password does not have an expiration date.
2. The password can be anything you want, but must meet these password strength requirements:
a. Include at least one special character.
b. Be at least 8 characters long.
3. Once you have chosen an acceptable password and click Done, the Encrypted Messages page will open.
On all subsequent uses, the system will ask for a username and password. Your username will always be your email address. If you
forget your password, click on the Forgot your password link. The system will send you an email to reset your password. Click on the
link in the email to be directed to the Barracuda Networks Message Center, which will ask for a new password and confirmation.
Picking Up Your Secure Email Message
The Barracuda Message Center provides you with a web interface much like any web based email program. You can view a list of your encrypted
messages, click on one to view the contents, delete one or more of them or download the message(s) to your local system.
View messages
Click on a message to view the contents. You are the only one who can read the message body. You can view the message headers by clicking
the Show All Headers link in the upper right. From the message window you can use buttons on the message bar Reply to, Reply All, Print,
Delete or Download the message. Attachments can be downloaded individually by clicking on them.
Reply to messages
If you reply to your encrypted message, the contents of your reply will also be encrypted. Once you click Reply, you can upload files and send
them securely back to the sender as part of the reply email by choosing Browse (to choose the selected files to add) or Add (to include an
attachment in the reply email). When finished, click Send. This will cause your reply message to be encrypted before returning to the sender. You
291
can also click Reply All to send your encrypted response to all other recipients of the message.
Saving Message Content
If you want to save the original email, the entire message (including attachments) can be saved by clicking the Download button.
Delete multiple messages
In the Encrypted Messages window, click the check box next to the message(s), and then click the Delete (trash can) icon on the tool bar. To
refresh the message list, click the Refresh icon next to the Delete icon on the tool bar.
292
Barracuda Spam Firewall User 's Guide 6 and Above
en
This guide describes how you can use the Barracuda Spam Firewall web interface to:
Check your quarantined messages
Classify messages as Spam and Not Spam
Manage whitelisting and blocklisting email addresses
Modify your User Preferences
The guide also covers use of the Barracuda Microsoft Outlook Add-in for classifying messages as spam or not spam and encrypting outbound
messages. The Add-in might be installed in your Microsoft Outlook mail client by your administrator or by you, depending on how the system is
configured.
Some features covered in this guide may not appear on your system, depending on your level of permissions as set by your administrator.
In this article:
en
Managing Your Quarantine Inbox
Receiving Messages from the Barracuda Spam Firewall
Greeting Message
Quarantine Summary Report
Using the Quarantine Interface
Logging into the Quarantine Interface
Using your Quarantine Inbox
Changing Your User Preferences
Changing Your Account Password
Changing Your Quarantine Settings
Enabling and Disabling Spam Scanning of your Email
Adding Email Addresses and Domains to Your Whitelist and Blocklist
Microsoft Outlook Add-in for Classifying Messages
Using the Microsoft Outlook Add-in
The Barracuda Spam Firewall sends you the following two types of messages:
Greeting Message
Spam Quarantine Summary Report
Greeting Message
The first time the Barracuda Spam Firewall quarantines an email intended for you, the system sends you a greeting message with a subject line
of User Quarantine Account Information. The greeting message contains the following information:
Welcome to the Barracuda Spam Firewall. This message contains the information you will need to access your
Spam Quarantine and Preferences.
Your account has been set to the following username and password:
Username: <your email address>
Password: <your default password>
Access your Spam Quarantine directly using the following link:
http://<barracuda system address or name>:8000
The Barracuda Spam Firewall automatically provides your login information (username and password) and the
link to access the quarantine interface. You should save this email because future messages from the system
do not contain your login information.
The Barracuda Spam Firewall sends you a daily quarantine summary report so you can view the quarantined messages you did not receive.
From the quarantine summary report you can also add messages to your whitelist, delete messages, and have messages delivered to your inbox.
293
Note that the quarantine summary report only goes out if new quarantined mail is saved in your account since the last notification cycle.
Each day the quarantine notification service runs for all users. If there is no new quarantined mail for your account since the last
notification cycle, or if you have logged into your account since then, no quarantine summary report will be generated and sent to
you for that same 24 hour period. Note also that links in the quarantine digest for viewing, delivering, whitelisting or deleting a message
from the quarantine inbox expire in 5 days from the date the digest is sent out.
The following shows an example of a quarantine summary report:
Figure 1: Example quarantine summary report ('digest').
At the end of every quarantine summary report is a link to the quarantine interface where you can set additional preferences and classify
messages as spam and not spam.
To log into your quarantine interface:
Click the link provided at the bottom of the Quarantine Summary Report (displayed above). The login page appears.
Enter your username and password, and click Login. Your login information resides in the greeting message sent to you from the
After logging into the quarantine interface, select the QUARANTINE INBOX tab to view a list of your quarantined messages. When you first start
using the quarantine interface, you should view this list on a daily basis and classify as many messages as you can. Clicking on an email displays
the message.
The Barracuda Spam Firewall has a Bayesian learning engine which, if enabled by your administrator, learns how to deal with future messages
based on the ones you classify as spam and not spam. The learning engine becomes more effective over time as you teach the system how to
classify messages and as you set up rules based on your whitelist and blocklist.
To effectively "train" your Bayesian database, you must classify at least 200 spam messages and 200 not spam messages from your
Quarantine Inbox, which will train the Bayesian database as to what word or phrase patterns that appear, perhaps multiple times,
throughout a message you consider to be valid content or characteristic of spam. Continue to classify an equal number of each type of
message as needed.
The following table describes the actions you can perform from this page.
Action
Description
Deliver
Delivers the selected message to your standard inbox.
Note: If you want to classify a message or add it to your whitelist,
make sure to do so before delivering the message to your inbox.
Once the Barracuda Spam Firewall delivers a message, it is removed
from your quarantine list.
Whitelist
294
Whitelist Adds the selected message to your whitelist so all future
emails from this sender are not quarantined unless the message
contains a virus or banned attachment type.
The Barracuda Spam Firewall adds the sending email address
exactly as it appears in the message to your personal whitelist.
Note that some commercial mailings may come from one of several
servers such as mail3.abcbank.com, and a subsequent message
may come from mail2.abcbank.com. See the section on managing
your whitelists and blocklists for tips on specifying whitelists with
greater effectiveness.
Delete
Deletes the selected message from your quarantine list. The main
reason to delete messages is to help you keep track of which
quarantine messages you have reviewed. You cannot recover
messages you have deleted.
Classify as Not Spam
Classifies the selected message as not spam. Note: Some bulk
commercial email may be considered useful by some users and
spam by others. For this reason, classifying such messages may not
be very effective because users may counteract each others’
classification. Instead of classifying bulk commercial email, it may be
more effective to add it to your whitelist (if you wish to receive such
messages) or blocklist (if you prefer not to receive them).
Classify as Spam
Classifies the selected message as spam.
After logging into your quarantine interface, depending on your account permissions, you can use the PREFERENCES tab to change your
account password, modify your quarantine and spam settings, and manage your whitelist and blocklist.
To change your account password, do one of the following:
On the quarantine interface login page, click Create New Password, or
After logging into your quarantine interface, go to PREFERENCES > Password. This option is not available if single sign-on has been
enabled via LDAP or Radius.
In the provided fields, enter your existing password and enter your new password twice. Click Save Changes when finished.
Note Changing your password breaks the links in your existing quarantine summary reports so you cannot delete, deliver, or whitelist
messages from those reports. New quarantine summary reports will contain updated links that you can use the same as before.
The following table describes the quarantine settings you can change from the PREFERENCES > Quarantine Settings page, depending on how
the administrator has configured your account:
Quarantine Setting
Description
Enable Quarantine
Whether the Barracuda Spam Firewall quarantines your messages.
If you select Yes, the Barracuda Spam Firewall does not deliver
quarantined messages to your general email inbox, but you can view
these messages from the quarantine interface and quarantine
summary reports.
If you select No, all messages that would have been quarantined for
you are delivered to your general email inbox with the subject line
prefixed with [QUAR]:. The Barracuda Spam Firewall administrator
can modify this prefix.
295
Notification Interval
The frequency the Barracuda Spam Firewall sends you quarantine
summary reports. The default is daily. The Barracuda Spam Firewall
only sends quarantine summary reports when one or more of your
emails have been quarantined.
If you select Never, you can still view your quarantined messages
from the quarantine interface, but you will not receive quarantine
summary reports.
Notification Address
The email address the Barracuda Spam Firewall should use to
deliver your quarantine summary report. Leave this field blank to use
the email address associated with your user account.
Default Language
The language in which you want to receive your quarantine
notifications.
This setting also sets the default encoding for handling unknown
character sets during filtering. All email notifications from the
Barracuda Spam Firewall are in UTF8 encoding.
If you do not want the Barracuda Spam Firewall scanning your emails for spam content, you can disable spam filtering from the PREFERENCES
> Spam Settings page. From this page you can also change the default spam scoring levels that determine when your emails are tagged,
quarantined or blocked.
When the Barracuda Spam Firewall receives an email for you, it scores the message for its spam probability. This score ranges from 0 (definitely
not spam) to 10 or higher (definitely spam). Based on this score, the Barracuda Spam Firewall either allows, quarantines, or blocks the message.
A setting of 10 for any setting disables that option. The following table describes the fields on the PREFERENCES > Spam Settings page.
The PREFERENCES > Whitelist/Blocklist page lets you specify email addresses and domains from which you do or do not want to receive
emails.
List Type
Description
Whitelist
The list of email addresses or domains from which you always wish
to receive
messages. The only time the Barracuda Spam Firewall blocks a
message from someone on your whitelist is when the message
contains a virus or a disallowed attachment file extension.
Blocklist
The list of senders from whom you never want to receive messages.
The Barracuda Spam Firewall immediately discards messages from
senders on your blocklist. These messages are not tagged or
quarantined are not tagged or quarantined and cannot be recovered.
The sender does not receive a notice that the message was deleted,
and neither do you. The only time a blocklisted email address is
delivered is if the same email address also appears in your whitelist.
To whitelist senders or to add senders to your blocklist, follow these steps:
1.
2.
3.
4.
Go to the PREFERENCES > Whitelist/Blocklist page.
A list of your existing whitelisted and blocklisted addresses appears on this page.
To delete a whitelist or a blocklist entry, click the trash can icon next to the address.
To add an entry, type an email address into the appropriate field and click the Add button.
Tips on specifying addresses
When adding addresses to your whitelist and blocklist, note the following tips:
If you enter a full email address, such as [email protected], just that user is specified. If you enter just a domain, such as yahoo.com,
all users in that domain are specified.
If you enter a domain such as barracudanetworks.com, all subdomains are also included, such as support.barracudanetworks.com and t
est.barracudanetworks.com.
Mass mailings often come from domains that do not resemble the company’s website name. For example, you may want to receive
296
mailings from historybookclub.com, but you will find that this site sends out its mailing from the domain hbcfyi.com. Examine the From:
address of an actual mailing that you are trying to whitelist or blocklist to determine what to enter.
Changing the Language of the Quarantine Interface
You can change the language of your quarantine interface by selecting a language from the dropdown menu in the upper right corner of the QUA
RANTINE INBOX and PREFERENCES tabs. Supported languages include Chinese, Japanese, Spanish, French, and others. The language you
select is only applied to your individual quarantine interface. No other user’s interface is affected.
Microsoft Outlook Add-in for Classifying Messages
Instead of using your quarantine inbox to classify your email messages, you can download a client add-in that lets you classify messages from
your MS Outlook application. Your Barracuda Spam Firewall administrator may chose not to make this add-in available. If this is the case, you
need to log into your quarantine inbox to classify your messages.
Downloading the Add-in
To download and install the client add-in that is needed to classify messages from MS Outlook:
1. Go to the login page of the administration interface and click the link below the login information, as shown in the following figure:
Figure 2. The login page lets you download the client add-in if your administrator has made it available.
2.
3.
4.
5.
If this link does not appear, then your Barracuda Spam Firewall administrator has configured the system to not make the add-in available
and the next section will not apply to your configuration.
After clicking the link, you'll see a popup prompting you to save the executable file BsfOutlookAddIn.exe. Click Save File.
Close MS Outlook on your system.
Run the file and follow the instructions in the setup wizard to install the add-in on your local system or network.
Re-start MS Outlook.
Using the Microsoft Outlook Add-in
Classifying Messages as Spam or Not-Spam
After downloading and installing the add-in, you can begin classifying messages using the green checkmark and the red X buttons in your MS
Outlook client. The green button marks messages as not spam and the red button marks messages as spam.
297
The MS Outlook add-in is configured to automatically:
Whitelist email addresses associated with sent messages and new contacts
Move spam-declared messages to the Deleted Items folder in your mail client
Whitelist the 'From:' email address within 'Not-Spam'-declared messages.
Optional Message Encryption
With the Barracuda Spam Firewall 5.1 or later, choose to encrypt any outbound message by clicking the Encrypt Message button that appears in
the Outlook New Message window, as shown in Figure 3, when the add-in is installed. The recipient of the message will retrieve it from the Barr
acuda Message Center.
Figure 3. Encrypting a message from Microsoft Outlook.
You can change the default behavior of the Outlook Add-in by going to the Tools menu in your MS Outlook client and selecting Options | Spam
Firewall tab.
298
Barracuda Spam Firewall User's Guide 5.x
en
This guide describes how you can check your quarantined messages, classify messages as spam and not spam, manage whitelisting and
blocklisting email addresses, and modify your user preferences using the Barracuda Spam Firewall interface. Some features covered in this guide
may not appear on your system, depending on your level of permissions as set by your administrator.
In this article:
en
Greeting Message
Using Microsoft Outlook and IBM Notes to Classify Messages
Using the Microsoft Outlook and IBM Notes Add-ins
The Barracuda Spam Firewall sends you the following two types of messages:
Greeting Message
Spam Quarantine Summary Report
Greeting Message
Depending on how the system administrator has configured the quarantine function, the Barracuda Spam Firewall will send you a greeting
message with a subject line of User Quarantine Account Information when one of the following happens:
Your account is first created by the system administrator
Your account is automatically created the first time the Barracuda Spam Firewall quarantines an email intended for you
The greeting message contains the following information:
Welcome to the Barracuda Spam Firewall. This message contains the
information you will need to access your Spam Quarantine and Preferences.
Your account has been set to the following username and password:
Username: <your email address> Password: <your default password>
Access your Spam Quarantine directly using the following link: http://<barracuda system address or
name>:8000
The Barracuda Spam Firewall automatically provides your login information (username and password) and the link to access the quarantine
interface. You should save this email because future messages from the system do not contain your login information.
The Barracuda Spam Firewall sends you a quarantine summary report either daily, weekly, or not at all, depending on how the system
administrator has configured it. This summary report enables you to view the quarantined messages you did not receive. From the quarantine
summary report you can also add messages to your whitelist, delete messages, and have messages delivered to your inbox.
Note that the quarantine summary report only goes out if new quarantined mail is saved in your account since the last notification cycle.
Each day the quarantine notification service runs for all users. If there is no new quarantined mail for your account since the last
notification cycle, or if you have logged into your account since then, no quarantine summary report will be generated and sent to
you for that same 24 hour period. Note also that links in the quarantine digest for viewing, delivering, whitelisting or deleting a message
from the quarantine inbox expire in 5 days from the date the digest is sent out.
299
The following shows an example of a quarantine summary report:
Figure 1: Sample quarantine summary report ('digest').
At the end of every quarantine summary report is a link to the quarantine interface where you can set additional preferences and classify
messages as spam and not spam.
To log into your quarantine interface:
Click the link provided at the bottom of the Quarantine Summary Report (displayed above). The login page appears.
Enter your username and password, and click Log In. Your login information resides in the greeting message sent to you from the
After logging into the quarantine interface, you'll see the QUARANTINE INBOX listing your quarantined messages. When you first start using the
quarantine interface, you should view this list on a daily basis and classify as many messages as you can. Clicking on an email displays the
message.
The Barracuda Spam Firewall has a Bayesian learning engine which, if enabled by your administrator, learns how to deal with future messages
based on the ones you classify as spam and not spam. The learning engine becomes more effective over time as you teach the system how to
classify messages and as you set up rules based on your whitelist and blocklist.
To effectively "train" your Bayesian database, you must classify at least 200 spam messages and 200 not spam messages from your
Quarantine Inbox, which will train the Bayesian database as to what word or phrase patterns that appear, perhaps multiple times,
throughout a message you consider to be valid content or characteristic of spam. Continue to classify an equal number of each type of
message as needed.
The following table describes the actions you can perform from this page.
Action
Description
Deliver
Delivers the selected message to your standard inbox.
Note: If you want to classify a message or add it to your whitelist,
make sure to do so before delivering the message to your inbox.
Once the Barracuda Spam Firewall delivers a message, it is removed
from your quarantine list.
Whitelist
300
Whitelist Adds the selected message to your whitelist so all future
emails from this sender are not quarantined unless the message
contains a virus or banned attachment type.
The Barracuda Spam Firewall adds the sending email address exactl
y as it appears in the message to your personal whitelist.
Note that some commercial mailings may come from one of several
servers such as mail3.abcbank.com, and a subsequent message
may come from mail2.abcbank.com. See the section on managing
your whitelists and blocklists for tips on specifying whitelists with
greater effectiveness.
Delete
Deletes the selected message from your quarantine list. The main
reason to delete messages is to help you keep track of which
quarantine messages you have reviewed. You cannot recover
messages you have deleted.
Classify as Not Spam
Classifies the selected message as not spam. Note: Some bulk
commercial email may be considered useful by some users and
spam by others. For this reason, classifying such messages may not
be very effective because users may counteract each others'
classification. Instead of classifying bulk commercial email, it may be
more effective to add it to your whitelist (if you wish to receive such
messages) or blocklist (if you prefer not to receive them).
Classify as Spam
Classifies the selected message as spam.
After logging into your quarantine interface, depending on your account permissions, you can use the PREFERENCES tab to change your
account password, modify your quarantine and spam settings, and manage your whitelist and blocklist.
To change your account password, do one of the following:
On the quarantine interface login page, click Create New Password, or
After logging into your quarantine interface, go to PREFERENCES > Password. This option is not available if single sign-on has been
enabled via LDAP or Radius.
In the provided fields, enter your existing password and enter your new password twice. Click Save Changes when finished.
Note Changing your password breaks the links in your existing quarantine summary reports so you cannot delete, deliver, or whitelist
messages from those reports. New quarantine summary reports will contain updated links that you can use the same as before.
The following table describes the quarantine settings you can change from the PREFERENCES > Quarantine Settings page, depending on how
the administrator has configured your account:
Quarantine Setting
Description
Enable Quarantine
Whether the Barracuda Spam Firewall quarantines your messages.
If you select Yes, the Barracuda Spam Firewall does not deliver
quarantined messages to your general email inbox, but you can view
these messages from the quarantine interface and quarantine
summary reports.
If you select No, all messages that would have been quarantined for
you are delivered to your general email inbox with the subject line
prefixed with [QUAR]. The Barracuda Spam Firewall administrator
can modify this prefix.
Notification Interval
301
The frequency the Barracuda Spam Firewall sends you quarantine
summary reports. The default is daily, with weekly and never also as
options.. The Barracuda Spam Firewall only sends quarantine
summary reports when one or more of your emails have been
quarantined.
If you select never, you can still view your quarantined messages
from the quarantine interface, but you will not receive quarantine
summary reports.
Notification Address
The email address the Barracuda Spam Firewall should use to delive
r your quarantine summary report. Leave this field blank to use the
email address associated with your user account.
Default Language
The language in which you want to receive your quarantine
notifications.
This setting also sets the default encoding for handling unknown
character sets during filtering. All email notifications from the
Barracuda Spam Firewall are in UTF8 encoding.
If you do not want the Barracuda Spam Firewall scanning your emails for spam content, you can disable spam filtering from the PREFERENCES
> Spam Settings page. From this page you can also change the default spam scoring levels that determine when your emails are tagged,
quarantined or blocked.
When the Barracuda Spam Firewall receives an email for you, it scores the message for its spam probability. This score ranges from 0 (definitely
not spam) to 10 or higher (definitely spam). Based on this score, the Barracuda Spam Firewall either allows, quarantines, or blocks the message.
A setting of 10 for any setting disables that option. The following table describes the fields on the PREFERENCES > Spam Settings page.
Setting
Description
Spam Scoring Enable/Disable
Enable Spam Scoring: Select Yes for the Barracuda Spam
Firewall to scan your emails for spam. Select No to have all your
messages delivered to you without being scanned for spam.
Spam Scoring
Use Domain Defaults: Select Yes to use the default scoring
levels. To configure the scoring levels yourself, select No and
make the desired changes in the Spam Scoring Levels section
described below.
Block: Messages with a score above this threshold are not
delivered to your inbox. Depending on how the system is
configured, the Barracuda Spam Firewall may notify you and the
sender that a blocked message could not be delivered. The
default value is 9.
Quarantine: Messages with a score above this threshold, but
below the block threshold, are forwarded to your quarantine
mailbox. The default setting is 10 (quarantine disabled). To
enable the quarantine feature, this setting must have a value
lower than the block threshold.
Tag: Messages with a score above this threshold, but below the
quarantine threshold, are delivered to you with the word [BULK]
added to the subject line. Any message with a score below this
setting is automatically allowed. The default value is 3.5.
Barracuda Bayesian Learning
302
Reset Personal Bayesian Database:
Click Reset to remove your Bayesian rules learned by the
Barracuda Spam Firewall from the point of installation. Use the
Reset button on a regular basis to clear out old classifications of
valid email versus spam to account for the fact that spam tactics
change rapidly and the word and phrase patterns that appear in
spam messages tend to change over time.
Thus, by resetting your Bayesian database regularly and
classifying 200 spam and not spam messages anew, you'll keep
your Bayesian database refreshed such that it has the best
chance of identifying spam with a very high level of accuracy.
Bayesian Database Backup
Back Up Bayesian Database: Click Backup to download a copy
of your Bayesian database to your local system. This backup
copy can then be uploaded to any Barracuda Spam Firewall,
including this one, in the case of a corrupt Bayesian installation.
Restore Database: Click Browse to select the backup file
containing your Bayesian database, and then click Upload Now
to load the Bayesian settings to this Barracuda Spam Firewall.
The backup file does not need to have originated from this
Barracuda Spam Firewall, nor from the same user database.
The PREFERENCES > Whitelist/Blocklist page lets you specify email addresses and domains from which you do or do not want to receive
emails.
List Type
Description
Whitelist
The list of email addresses or domains from which you always wish
to receive
messages. The only time the Barracuda Spam Firewall blocks a
message from someone on your whitelist is when the message
contains a virus or a disallowed attachment file extension.
Blocklist
The list of senders from whom you never want to receive messages.
The Barracuda Spam Firewall immediately discards messages from
senders on your blocklist. These messages are not tagged or
quarantined and cannot be recovered.
The sender does not receive a notice that the message was deleted,
and neither do you. The only time a blocklisted email address is
delivered is if the same email address also appears in your whitelist.
To whitelist senders or to add senders to your blocklist, follow these steps:
1.
2.
3.
4.
Go to the PREFERENCES > Whitelist/Blocklist page.
A list of your existing whitelisted and blocklisted addresses appears on this page.
To delete a whitelist or a blocklist entry, click the trash can icon next to the address.
To add an entry, type an email address into the appropriate field and click the Add button.
Tips on specifying addresses
When adding addresses to your whitelist and blocklist, note the following tips:
If you enter a full email address, such as [email protected], just that user is specified. If you enter just a domain, such as yahoo.com,
all users in that domain are specified.
If you enter a domain such as barracudanetworks.com, all subdomains are also included, such as support.barracudanetworks.com and t
est.barracudanetworks.com.
Mass mailings often come from domains that do not resemble the company's website name. For example, you may want to receive
mailings from historybookclub.com, but you will find that this site sends out its mailing from the domain hbcfyi.com. Examine the From:
address of an actual mailing that you are trying to whitelist or blocklist to determine what to enter.
Changing the Language of the Quarantine Interface
You can change the language of your quarantine interface by selecting a language from the dropdown menu in the upper right corner of the QUA
RANTINE INBOX and PREFERENCES tabs. Supported languages include Chinese, Japanese, Spanish, French, and others. The language you
select is only applied to your individual quarantine interface. No other user's interface is affected.
Using Microsoft Outlook and IBM Notes to Classify Messages
303
Instead of using your quarantine inbox to classify your email messages, you can download a client add-in that lets you classify messages from
your Microsoft Outlook or IBM Notes application. Your Barracuda Spam Firewall administrator may chose not to make this add-in available.
If this is the case, you need to use your quarantine inbox to classify your messages.
Downloading the Client Add-in
To download the client add-in that is needed to classify messages from Microsoft Outlook or IBM Notes, go to the login page of the administration
interface and click the link below the login information, as shown in the following figure:
If this link does not appear, then your Barracuda Spam Firewall administrator has configured the system to not make the add-in available and the
next section will not apply to your configuration.
Using the Microsoft Outlook and IBM Notes Add-ins
After downloading and installing the add-in, you can begin classifying messages using the Mark as Spam and Mark as Not Spam icons in your
Microsoft Outlook or IBM Notes client. These icons are located in the upper right of your email client if the add-in has been installed. Highlight one
or more messages in your email client and click Mark as Spam if you think these messages are spam and should not have been delivered to
your inbox. Do the same for messages which are NOT spam, using the Mark as Spam icon, for good messages. This will train your Bayesian
database on the Barracuda Spam Firewall so it will become an 'expert' at what you do or do not consider to be spam.
The Microsoft Outlook and IBM Notes add-ins are configured to automatically:
Whitelist email addresses associated with sent messages and new contacts
Move messages you mark as Spam to the Deleted Items folder in your mail client
Whitelist the 'From:' email address within messages you mark as Not-Spam.
The Outlook Add-in also provides optional message Encryption. With the Barracuda Spam Firewall 5.1 or later, choose to encrypt any outbound
message by clicking the Encrypt Message button that appears in the Outlook New Message window when the add-in is installed.
304
You can change the default behavior of the Outlook Add-in by going to the Tools menu in your Microsoft Outlook client and selecting Options |
Spam Firewall tab.
305
Barracuda Outlook Add-In Overview 6 and Above
en
This guide applies to the Barracuda Spam Firewall 300 and higher, version 6.0 and higher. The Barracuda Outlook Add-in is
compatible with Microsoft Outlook 2007 and Outlook 2010 and 2013 32-bit and 64-bit versions. If you are running version 6.0.0.028
or later of the Barracuda Spam Firewall firmware, you must upgrade your Barracuda Outlook Add-in to version 6.0.21 or later (see
the USERS > User Features page).
If both per-user quarantine and per-user Bayesian are enabled, the administrator can install an add-in, or choose to allow users to download an
add-in, that provides the user with the following tools:
Classify messages as Spam or Not Spam directly from their MS Outlook client. This classification helps train the user’s personal
Bayesian database, and results in higher accuracy for the Barracuda Spam Firewall. Users must have a quarantine account on the
Barracuda Spam Firewall to use the Barracuda Outlook add-in. For information about automatically or manually creating quarantine
accounts for users, see Creating and Managing Accounts. Note that all feedback is stored in a per-user Bayesian database on the
system. This mechanism prevents users from compromising the global Bayesian database, and results in more specific scoring due to
learning about a user’s personal mail preferences.
Message encryption. The user can click a button in the MS Outlook client to encrypt the message contents before sending it. Any
messages encrypted using the add-In will appear in the Barracuda Spam Firewall Message Log with a Reason of Outlook Add-In. Email
encryption is performed by the Barracuda Email Encryption Service, the same way encryption is performed when configured on the
Barracuda Spam Firewall. The difference is that, with the add-in installed on the user’s machine, their outgoing email can be encrypted
inside the network, securing email exchanged among people in the organization. See Encryption of Outbound Mail 6 and Above for more
information about configuring email encryption.
Sender whitelisting. The user can decide who should be on their whitelist.
For instructions on the installation and configuration of the Barracuda Outlook Add-In for the Windows environment, please see the Barracuda
Spam Firewall Outlook Add-In Deployment Guide.
Getting the Add-In
It is up to the administrator of the Barracuda Spam Firewall to decide whether or not users should be given access to this add-in. If the admin
wishes to provide the add-in, download capability can be activated for the users under the USERS > User Features page. Users will then be able
to download and install the add-in from a link on the login screen. If the admin chooses to only provide the add-in to a small subset of users, the
add-in can be downloaded from the page where activation is performed and distributed to the necessary users. The add-in is downloaded in a zip
file containing .msi files, and is available in both 32 and 64-bit versions.
Using the Add-In
Spam / Not Spam Classification
Once installed, the add-in makes itself available to the user through the toolbar inside MS Outlook. Two icons are provided that perform the
necessary “Spam” or “Not Spam” classification functionality:
• A red envelope with an “X” in the lower right corner to classify messages as spam.
• A green envelope with a checkmark to classify messages as not-spam.
Figure 1: Users can mark messages as Spam or Not Spam using icons in their mail client
Select one or more items from the message window and click on the Mark as Spam / Mark as Not Spam icon to submit the messages to the
Barracuda Spam Firewall for classification. For convenience, the toolbar icons are also provided when a mail message is opened in a new
window for viewing. If desired, the message can be classified immediately from that window.
Please note that Bayesian learning is only effective when the differences between “Spam” and “Not Spam” are known to the system. Therefore it
is important to make sure that both types of messages are classified from user desktops. This add-in is designed to make that classification
process as easy as possible. However, it is up to each user to make sure the items they classify from the add-in are really considered spam or
not spam as it will affect the scoring of future messages coming onto the system for them.
Figure 2: Users can encrypt a message
306
Encryption
With the Barracuda Spam Firewall 5.1 or later , when the user opens the New Message window in Microsoft Outlook, the Encrypt Message icon
will appear within the window as shown in Figure 2, providing the option to encrypt the message contents before sending it. When the user sends
an encrypted message using the Barracuda Outlook Add-In, the recipient will receive a notification email from the Barracuda Message Center
that includes a link the recipient can click to retrieve their message. The Barracuda Message Center provides a web client much like any web mail
client that the recipient can log into to view and manage encrypted messages. Note that the Encrypt Message icon can be disabled through
GPO.
For more information about the Barracuda Email Encryption Service, see Encryption of Outbound Mail 6 and Above.
307
Barracuda Outlook Add-In Overview 5.x
en
The Barracuda Outlook Add-In is compatible with MS Outlook 2003-2013 (version 2013 requires Barracuda Spam Firewall
5.1.3.007 and higher). This guide applies to the Barracuda Spam Firewall 300 and higher, version 5.x.
If both per-user quarantine and per-user Bayesian are enabled, the administrator can install an add-in, or choose to allow users to download an
add-in, that provides the user with the following tools:
Classify messages as Spam or Not Spam directly from their MS Outlook client. This classification helps train the user’s personal
Bayesian database, and results in higher accuracy for the Barracuda Spam Firewall. Users must have a quarantine account on the
Barracuda Spam Firewall to use the Barracuda Outlook add-in. For information about automatically or manually creating quarantine
accounts for users, see Creating and Managing Accounts. Note that all feedback is stored in a per-user Bayesian database on the
system. This mechanism prevents users from compromising the global Bayesian database, and results in more specific scoring due to
learning about a user’s personal mail preferences.
Message encryption. The user can click a button in the MS Outlook client to encrypt the message contents before sending it. Any
messages encrypted using the add-In will appear in the Barracuda Spam Firewall Message Log with a Reason of Outlook Add-In. Email
encryption is performed by the Barracuda Email Encryption Service, the same way encryption is performed when configured on the
Barracuda Spam Firewall. The difference is that, with the add-in installed on the user’s machine, their outgoing email can be encrypted
inside the network, securing email exchanged among people in the organization. See Encryption of Outbound Mail 5.x for more
information about configuring email encryption.
For instructions on the installation and configuration of the Barracuda Outlook Add-In for the Windows environment, please see the Barracuda
Spam Firewall Outlook Add-In Deployment Guide 5.x.
Getting the Add-In
It is up to the administrator of the Barracuda Spam Firewall to decide whether or not users should be given access to this add-in. If the admin
wishes to provide the add-in, download capability can be activated for the users under the USERS > User Features page. Users will then be able
to download and install the add-in from a link on the login screen. If the admin chooses to only provide the add-in to a small subset of users, the
add-in can be downloaded from the page where activation is performed and distributed to the necessary users. The add-in is downloaded in a zip
file containing .msi files, and is available in both 32 and 64-bit versions.
Using the Add-In
Spam / Not Spam Classification
Once installed, the add-in makes itself available to the user through the toolbar inside MS Outlook. Two icons are provided that perform the
necessary "Spam" or "Not Spam" classification functionality:
A red envelope with a red X in the lower right corner to classify messages as spam.
A green envelope with a checkmark to classify messages as not-spam.
To use the add-in, select one or more items from the message window and click on the spam / not-spam icon to submit the messages to the
Barracuda Spam Firewall for classification. For convenience, the toolbar icons are also provided when a mail message is opened in a new
window for viewing. If desired, the message can be classified immediately from that window.
Please note that Bayesian learning is only effective when the differences between "Spam" and "Not Spam" are known to the system. Therefore it
is important to make sure that both types of messages are classified from user desktops. This add-in is designed to make that classification
process as easy as possible. However, it is up to each user to make sure the items they classify from the add-in are really considered spam or
not spam as it will affect the scoring of future messages coming onto the system for them.
Encryption
With the Barracuda Spam Firewall 5.1 or later, when the user opens the New Message window in Microsoft Outlook, the Encrypt Message butto
n will appear within the window, providing the option to encrypt the message contents before sending it. When the user sends an encrypted
message using the Barracuda Outlook Add-In, the recipient will receive a notification email from the Barracuda Message Center that includes a
link the recipient can click to retrieve their message. The Barracuda Message Center provides a web client much like any web mail client that the
recipient can log into to view and manage encrypted messages. Note that the Encrypt Message button can be disabled through GPO.
For more information about the Barracuda Email Encryption Service, see Encryption of Outbound Mail 5.x.
308
Barracuda Spam Firewall Outlook Add-In Deployment Guide 6.1.2 and Above
en
This article applies to the Barracuda Spam Firewall running version 6.1.2 and above. For information about the features of the
Barracuda Spam Firewall Outlook Add-In, please see the Barracuda Outlook Add-In Overview 6 and Above. The Barracuda
Microsoft Outlook Add-In is compatible with MS Outlook 2003 - 2013. If you are running the Barracuda Spam Firewall version
6.0.0.028 or above, you must upgrade your Barracuda Outlook Add-in to version 6.0.21 or above (see the USERS > User Features
page).
If you want end-users to use Bayesian classification via this add-in, you must enable Per-User Quarantine on the Barracuda Spam
Firewall from BASIC > Quarantine page in the Inbound Quarantine Type section. See also Bayesian Analysis Inbound. This
guide applies to the Barracuda Spam Firewall 300 and above, version 6.0 and above.
In this article:
en
Step 1: Install the Outlook Add-In Deployment Kit
Step 2. Optional: Configure the Outlook Add-In
Step 3. Deploy the MSI File
Deploying the Add-In to Machines with 64-bit Windows and 32-bit Outlook
Finishing the Configuration
Testing
Notify Users
Troubleshooting
Configure the Add-In from the MS Outlook Client
If the SMTP option Remove Barracuda Headers is turned off in the ADVANCED > Email Protocol page, any custom X-headers that
the Barracuda Spam Firewall has applied before the message leaves the appliance will be removed. Important: If these headers are
removed, the Barracuda Outlook add-in or other add-in will not function.
Note that the language for add-in options is determined by your Microsoft Office installation locale. Supported languages for the add-in include:
English
Spanish (continental)
French
Japanese
Dutch
Italian
Chinese
Polish
German
Step 1: Install the Outlook Add-In Deployment Kit
1. Log into your Barracuda Spam Firewall as an administrator.
2. Navigate to USERS > User Features and download the Outlook Add-In Deployment Kit (a .zip file) to the local system running Windows
Vista or above.
3. Extract the contents somewhere easily accessible. The deployment kit should contain the following:
Barracuda Spam Firewall Outlook Add-in installer for Outlook 2010 64-bit or for Outlook 2013 64-bit (BsfOutlookAddIn-version
_x64.msi)
Barracuda Spam Firewall Outlook Add-in installer for all other versions of Outlook (BsfOutlookAddIn-version_x86.msi).
Barracuda Spam Firewall Outlook Add-in Administrator module (Barracuda Spam Firewall Outlook Add-In version.admx
Step 2. Optional: Configure the Outlook Add-In
If you want to use GPO:
1. Go to the installation location, and open the ADMX folder, for example:
C:\Program Files\Barracuda\Spam Firewall\Deployment Kit\ADMX
2. Copy the ADMX and ADML locale directories to the PolicyDefinitions folder on your system, for example:
%systemroot%\sysvol\domain\policies\PolicyDefinitions
This procedure applies to domain controllers running Windows Server 2008 or higher; to edit local policy or domain policies on
a domain controller running Windows Server 2003 or earlier, consult Microsoft's documentation.
3. Start the Group Policy (GPO) Editor for the domain where you will be installing the Add-In. You can edit the default policy or create a new
309
3.
policy object and link it to the desired container, for example, the particular OU containing the computers of users that will be using the
Add-In.
In order to create and edit domain-based GPOs with the latest Group Policy settings using ADMX files, you must have a Windo
ws Server 2008 domain name resolvable through a DNS Server, and a Windows Vista system to view policy settings from
ADMX files while editing the domain-based GPO.
In the GPO, expand User Configuration > Administrative Templates > Barracuda > Spam Firewall > Outlook Add-In:
Configure any policies as needed. You will need to recreate any policies you previously configured, and then remove the old ADM
template.
Step 3. Deploy the MSI File
1. Open the GPO Editor for the organization that is to use the Barracuda Spam Firewall Outlook Add-in, e.g., the default domain policy.
2. Either edit the default policy, or create a new policy object, then link it to the desired container. For example, the particular OU containing
the computers on which the add-in is to be installed.
3. In the GPO, navigate to Computer Configuration > Policies > Software Settings > Software Installation :
4. Right-click Software Installation, point to New, and click Package:
4.
310
Enter the UNC path to the .msi file located in the shared folder. For example, enter: \\fileserver\deploy
Click Open. In the Deploy Software dialog box, click Assigned:
Click OK . The policy displays in the GPO Editor window.
Deploying the Add-In to Machines with 64-bit Windows and 32-bit Outlook
If any of the machines in your environment have a 64-bit version of Windows installed but are using a 32-bit version of Outlook, you will need to
deploy the 32-bit MSI to these machines. If you are also deploying the 64-bit MSI for machines with both 64-bit Windows and 64-bit Outlook, then
both software deployment policies will apply to the machines with 32-bit Outlook, which will result in both MSIs being installed on these
machines. Since Outlook will only load the Add-In that matches its bitness, this should not cause any problems.
1. In the GPO Editor, navigate toComputer Configuration > Policies > Software Settings , and clickSoftware Installation.
2. Right-click the 32-bitBarracuda Spam Firewall Outlook AddIn, and clickProperties.
3. Click the Deployment tab, and click Advanced. In the Advanced deployment options section, select Make this 32-bit X86
application available to Win64 machines.
4. Click OK. In the Properties dialog box, click Apply, and click OK to to save your settings and close the dialog box.
Finishing the Configuration
311
After the Barracuda Spam Firewall Outlook AddIn is installed (either manually or through GPO), there is no initial configured identification with
your Barracuda Spam Firewall. This identification happens automatically as the add-in scans the user's inbox for recent messages and inspects
each message’s headers for a Barracuda Spam Firewall URI. If none is found, the add-in will monitor the user's inbox for new messages and
scan each new message header for a Barracuda Spam Firewall URI. When a Barracuda Spam Firewall URI is found, an authentication probe will
be initiated with that Barracuda Spam Firewall. The Barracuda Spam Firewall then sends an authentication probe via email to the user’s email
address, and the add-in will intercept the probe, extract the required authentication information contained in the probe, and then delete it. This
process is transparent to the user. Once the probe is received, the user is authenticated, and all of the add-in features are available for use.
Typically, this process should take no more than a few minutes.
Testing
Complete the following steps to test the Barracuda Spam Firewall Outlook Add-in deployment.
Group Policy updates can take several minutes to post; run gpupdate /force to perform an immediate update.
1. Restart a computer that is joined to the domain.
2. Verify that the Outlook Add-In is installed when you log in, and that the configured policies are applied.
Notify Users
Once the MSI file is successfully deployed, send the Outlook Add-In access details to your users. For additional resources, see the Barracuda
Spam Firewall User 's Guide 6.x.
Troubleshooting
1. A common cause of failure is the user and/or the user's computer does not have adequate access to the share location. Verify that that
all access and network privileges have been configured appropriately.
2. Additional error messages may be found in the Event Log on the domain computer.
3. If the Event Log has no useful information, consider enabling verbose logging and restarting the computer.
Configure the Add-In from the MS Outlook Client
For Microsoft Outlook 2003 and 2007:
1. Click Tools > Options.
2. Click the Barracuda Networks tab.
3. Click Configure to set whitelist options and configure actions for clicking the Spam and Not Spam buttons in the client.
For Microsoft Outlook 2010 and 2013:
1. In the MS Outlook client, click File > Barracuda Networks (Note that the UI graphics may look different between the versions, but the
actions you take are the same).
Figure 2: The File menu has a Barracuda Networks menu option.
2. Click the Configure button and configure whitelist and spam settings as described above.
Figure 3: The Barracuda Networks menu shows the Configure button to configure the add-in.
312
313
Barracuda Spam Firewall Outlook Add-In Deployment Guide 5.x
en
For information about the features of the Barracuda Spam Firewall Outlook Add-In, please see the Barracuda Outlook Add-In Overview
5.x. To use this add-in, you must enable Per-User quarantine on the Barracuda Spam Firewall from BASIC > Quarantine page in the I
nbound Quarantine Type section. Also see Barracuda Spam Firewall User's Guide 5.x.
In this article:
en
Step 1: Install the Barracuda Spam Firewall Outlook Add-In Deployment Kit
Step 2: Configure the Add-In
Step 3: Deploy the MSI
Support for Outlook 64-bit (2010 and 2013)
Step 4: Testing
Step 5: Troubleshooting
Note that the language for installation instructions is determined by your Microsoft Office installation locale. Supported languages for the add-in
include:
English
Spanish (continental)
French
Japanese
Dutch
Italian
Chinese
Polish
German
Step 1: Install the Barracuda Spam Firewall Outlook Add-In Deployment Kit
1.
2.
3.
4.
Log into your Barracuda Spam Firewall as an administrator.
Navigate to USERS > User Features.
Download the Outlook Add-In Deployment Kit.
Extract the contents somewhere easily accessible. It should contain:
a. Installer for the add-in for Outlook 64-bit (BsfOutlookAddIn-version_x64.msi) for Outlook 2010 and 2013.
b. Installer for the add-in for all other versions of Outlook (BsfOutlookAddIn-version_x86.msi).
c. The administrator module for the add-in (Barracuda Spam Firewall Outlook Add-In version.adm).
5. Move (or copy) the file ending in .adm to your local %systemroot%\inf, directory. Typically, this will be: C:\Windows.
6. Copy the .msi file(s) to a location that is accessible by your user.
Configuring the Software Installation Network Share
If you do not already have a network share for GPO software deployment, you'll need to create one. The share should be
accessible from all the machines that the software will be deployed to. The permissions for the share should give read access
to the "Everyone" group, and the permissions for the underlying NTFS folder should give read access to the "Authenticated
Users" group. The software will be installed by the machines themselves rather than by users, and machines are not members
of the "Everyone" group, so this modification to the default permissions is required.
7. Open the GPO Editor for whichever organization will be using the add-in (e.g. the default domain policy).
8. Either edit the default policy or create a new policy object, then link it to the desired container; for example, the particular OU containing
the computers on which the add-in will be installed.
9. Expand User Configuration.
10. Right-click on Administrative Templates, select All Tasks, then Add/Remove Templates.
11. Navigate to %systemroot%\inf, select Barracuda Spam Firewall Outlook Add-In<version#>.adm, and press Add….
Step 2: Configure the Add-In
1. While still in the GPO Editor, go to User Configuration\Administrative Templates and expand the Barracuda node that should now be
visible.
2. Click on Spam Firewall.
3. Click on Barracuda Spam Firewall Outlook Add-In version.
4. Configure settings as required. For an explanation of the available settings, click the Explain tab of the policy.
Step 3: Deploy the MSI
1.
314
1. Start the Group Policy Editor for the domain for which you'll be installing the add-in.
2. Either edit the default policy or create a new policy object, then link it to the desired container; for example, the particular OU containing
the computers of users that should have the add-in. Please note that the software deployment policy must be for computers, not users.
3. Navigate to Computer Configuration/Software Settings/Software Installation.
4. Right-click on Software Installation and select New/Package…. Enter the UNC path to the MSI located in the shared folder.
5. Click OK.
Support for Outlook 64-bit (2010 and 2013)
If you have both 32-bit and 64-bit machines in your environment, but none of the 64-bit machines are running Outlook 64-bit, then the x86 version
of the MSI is the recommended version to use and is what is deployed by default to all 32-bit as well as 64-bit machines. However, if there are
some 64-bit machines that do have Outlook 64-bit installed, then there are 3 possible scenarios:
Scenario 1: Every 64-bit machine in your environment has Outlook 64-bit installed. In this case, perform all of the following steps:
a. Go the deployment tab for the 32-bit package.
b. Click the Advanced… button, and uncheck the Make this 32-bit x86 application available to Win64 machines option.
c. Repeat steps 3.1 - 3.5 for the 64-bit MSI.
The 32-bit MSI will now be deployed only to 32-bit machines, while the
64-bit MSI will be deployed only to 64-bit machines.
Scenario 2: Some 64-bit machines in your environment have Outlook 64-bit installed while others have the 32-bit versions of various other
Outlook versions on them, and Outlook was installed through a GPO. In this case, perform all of the following steps:
a. Apply the policy you created in the above steps to only those computers that were targeted for the installation of 32-bit Outlook.
b. Repeat steps 3.1 - 3.5 for the 64-bit MSI, and apply this second policy to only those computers that were targeted for the
installation of Outlook 64-bit.
The 64-bit MSI will only be installed on those computers with Outlook 64-bit installed, while the 32-bit add-in will be installed for all other
computers to which the policy has been applied.
Scenario 3: The 64-bit machines in your environment have a mixture of Outlook 2010 and 2013 64-bit and other 32-bit versions of Outlook
installed, but there are no existing AD containers that specify which of those computers have Outlook 64-bit on them. In this case, perform
only one of the following steps:
a. Manually create and populate these AD containers and then perform the steps in Scenario #2 above.
b. Consider installing Outlook 2010 32-bit on all computers (unless you have users that require the 64-bit capabilities of Office
64-bit)
c. Manually install the correct version of the add-in on each of the machines.
d. Allow your users to install the correct version of the add-in installer for themselves (they must have administrative privileges on
their computers).
Step 4: Testing
1. Remember that Group Policy updates can take several minutes to post. You can run
gpupdate /force
to perform an immediate update.
2. Restart a computer that is joined to the domain.
3. The add-in should be installed when you log in, and the policies you have configured should be applied.
Step 5: Troubleshooting
1. A common cause of failure is the user and/or the user's computer does not have adequate access to the share location. Verify that that
all access and network privileges have been configured appropriately.
2. Additional error messages may be found in the Event Log on the domain computer.
3. If the Event Log has no useful information, consider enabling verbose logging and restarting the computer.
4. Additional information on fixing Group Policy issues can be found here: http://technet.microsoft.com/en-us/library/cc775423.aspxh
315
SMTP Error Codes
en
This is a basic guide to the SMTP return (or 'error') codes you may see for rejected or deferred messages in the Message Log of the Barracuda
Spam Firewall when an outbound message cannot be delivered to or accepted by the destination mail server. Depending on the actual problem it
encounters, the destination mail server that did not accept the message may not be able to provide detailed help on how to resolve a problem. In
this case the mail server may only provide an SMTP error code in the server's log, or in the text of the message returned to the sender..
To view an SMTP error code for a rejected or deferred message in the Barracuda Spam Firewall web interface:
1. Go to the BASIC > Message Log page.
2. Double click on the message.
3. In the Delivery Status field you might see Rejected and a Delivery Detail with an SMTP error code. This example shows error 554:
SMTP error codes you'll see in the Delivery Details field of the Message Details popup for a rejected or deferred message include the following,
with more details listed in the table below:
420 - The message has been deferred due to suspect content.Try again later.
421 - The service is not available and the connection will be closed.
450 - The requested command failed because the user's mailbox was unavailable (for example because it was locked). Try again later.
451 - The command has been aborted due to a server error. Perhaps contact the the administrator to alert him/her of the issue.
452 - The command has been aborted because the server has insufficient system storage.
454 - TLS encoding is not available due to a temporary condition.
500 - The server could not recognize the command due to a syntax error.
501 - A syntax error was encountered in command arguments.
502 - This command is not implemented.
503 - The server has encountered a bad sequence of commands.
504 - A command parameter is not implemented.
530 - Must issue STARTTLS command.
535 - Authentication failed.
550 - The requested command failed because the user's mailbox was unavailable (for example, because it was not found, or because
the command was rejected for policy reasons).
551 - The recipient is not local to the server. The server then gives a forwarding address to try.
552 - The action was aborted due to exceeded storage allocation.
553 - The command was aborted because the mailbox name is invalid.
554 - The transaction failed.
Error
Code
Description
4XX_RVERIFY_DEFER
400
Deferred: temporary directory error
4XX_SUSPECT_REALTIME
420
Deferred due to suspect content, please try
again later
4XX_TIMEOUT
421
Error: timeout
4XX_CLIENT_DISCONNECT
421
Client disconnected
4XX_EINTERNAL
421
Internal error
4XX_ESEND
421
Failed to reply to client
4XX_TOO_MANY_ERRORS
421
Too many errors
316
4XX_MSG_PER_SESSION
421
Error: too many messages in one session
4XX_TEMP_FAIL
421
Service not available, closing transmission
channel. Try again later.
4XX_VIRUSSCAN_TEMP_FAIL
421
Temporary failure. Try again later.
4XX_TEMP_RECIP
450
Requested action not taken: mailbox
unavailable.
4XX_EINTERNAL
451
Internal error.
4XX_EINTERNAL
451
Requested action aborted: local error in
processing.
4XX_TOO_MANY_RECIPS
452
Too many recipients.
4XX_TLS_TEMP_FAIL
454
TLS not available due to temporary reason.
4XX_SYNTAX_ERROR
500
Syntax error, command unrecognized.
5XX_INVALID_CHAR_RECIP
500
Syntax error - invalid character.
5XX_INVALID_PARAM
501
Syntax error in parameters or arguments.
5XX_AUTH_ABORT
501
Authentication aborted.
5XX_AUTH_MALFORMED
501
Malformed authentication input.
5XX_AUTH_RESPONSE_BAD
501
Error: malformed authentication response.
5XX_DATA_LINE_TOO_LONG
501
Command line too long or no terminating
CRLF in line buffer .
5XX_DATA_MISSING_CRLF
501
No terminating CRLF in line buffer.
5XX_NO_SUCH_COMMAND
502
This command is not implemented.
5XX_MISSING_EHLO
503
Error: send HELO/EHLO first.
5XX_ALREADY_AUTH
503
Error: already authenticated.
5XX_AUTH_REQUIRES_TLS
503
Issue STARTTLS first before using clear text
password.
5XX_BAD_AUTH_COMMAND_SEQ
503
Bad sequence of authentication commands Try the following: AUTH CRAM-MD5, AUTH
LOGIN.
5XX_BAD_COMMAND_SEQ
503
Bad sequence of commands.
504
Error: encryption required for requested
authentication mechanism.
5XX_NEED_FQDN
504
Need Fully Qualified Address (FQDN).
5XX_ERROR_PARAM
504
Command parameter not implemented.
5XX_AUTH_UNSUPPORTED
504
Error: unsupported mechanism.
5XX_AUTH_TYPE
504
Unrecognized authentication type.
530
Authentication required.
5XX_REQUIRES_TLS
530
Must issue STARTTLS.
5XX_AUTH_FAILED
535
Authentication failed.
5XX_BLOCKED_RECIP
550
Recipient email address rejected.
5XX_BLOCKED_IP
550
Blocked IP address.
5XX_BLOCKED_SENDER2
550
Sender Rejected.
5XX_BLOCKED_SENDER3
550
Sender email address rejected.
317
5XX_INVALID_DOMAIN
550
No such domain at this location.
5XX_HANGUP
550
Executing hangup request.
5XX_DISCARD
550
Executing discard request.
5XX_EMPTY_SENDER
550
Empty envelope senders not allowed.
5XX_INVALID_SENDER2
550
Invalid sender address.
5XX_BLOCKED_IP2
550
Sender IP address rejected.
5XX_SPF_FAIL
550
Rejecting for Sender Policy Framework
(SPF).
5XX_RECIP 550
550
Requested action not taken: mailbox
unavailable.
5XX_SPOOFED
550
Rejecting spoofed message.
5XX_MSG_SIZE
552
Error: message too large.
5XX_MSG_SIZE2
552
Message size exceeds fixed limit.
5XX_FAIL_RECIP
553
Requested action not taken: mailbox name
not allowed.
5XX_NO_ACTION
553
Requested action not taken.
5XX_INVALID_RECIP
553
Requested action not taken: mailbox name
not allowed.
5XX_FAILED
554
Transaction failed.
5XX_BLOCKED_VIRUS
554
Rejected due to virus.
5XX_BLOCKED_SPAM
554
Rejected due to spam content.
5XX_BLOCKED_NO_PTR
554
IP name lookup failed. No PTR record found
for the given IP address.
5XX_BLOCKED_RATE
554
Too many connections from origin (rate
control).
5XX_BLOCKED_RATE2
554
Too many connections to server (rate
control).
5XX_BLOCKED_RBL
554
Service unavailable; client host blocked. The
final sending domain or IP address may be
on a Real Time Blacklist (RBL).
5XX_BLOCKED_ATT
554
Rejecting banned file attachment.
5XX_BLOCKED_ATT_ENC
554
Rejecting password protected file
attachment.
5XX_BLOCKED_BBL
554
Service unavailable; client host [IP or
hostname] blocked using Barracuda
Reputation; http://www.barracudanetworks.c
om/reputation/
5XX_BLOCKED_DLP
554
Rejected due to banned content.
5XX_BLOCKED_SPAM2
554
Rejected due to banned content.
318
How to Customize SMTP Response Messages
en
Advanced Feature
This feature is for advanced administrators and internet service providers.
Customizing SMTP Responses
From the ADVANCED > SMTP Responses page in the web interface you can choose to override default SMTP error response messages with
customized text. Only ASCII characters are supported. To create the customized text:
1. Check the error code line to enable use of an alternate/customized message.
2. Edit the default text. You can optionally use one or more of the macros shown in the top section of the page to insert server hostname,
client HELO/EHLO, sending client IP address and/or other email message information into the response message.
Use macros from the top of the page to insert customized information such as an IP address. In this example, the phrase your IP is replaced
using the ${client[addr]} - sending client IP address macro.
An ISP might want to customize the Need Fully Qualified Address message:
319
Hardware Compliance
en
en
This section contains compliance information for the appliance.
Notice for the USA
Compliance Information Statement (Declaration of Conformity Procedure) DoC FCC Part 15: This device complies with part 15 of the FCC Rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received including interference that may cause undesired operation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user in
encouraged to try one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Plug the equipment into an outlet on a circuit different from that of the receiver.
Consult the dealer on an experienced radio/ television technician for help.
Notice for Canada
This apparatus complies with the Class B limits for radio interference as specified in the Canadian Department of Communication Radio
Interference Regulations.
Notice for Europe (CE Mark)
This product is in conformity with the Council Directive 89/336/EEC, 92/31/EEC (EMC).
Power Requirements
AC input voltage 100-240 volts; frequency 50/60 Hz.
320
Limited Warranty and License
en
Limited Warranty
Barracuda Networks, Inc., or the Barracuda Networks, Inc. subsidiary or authorized Distributor selling the Barracuda Networks product, if sale is
not directly by Barracuda Networks, Inc., (“Barracuda Networks”) warrants that commencing from the date of delivery to Customer (but in case of
resale by a Barracuda Networks reseller, commencing not more than sixty (60) days after original shipment by Barracuda Networks, Inc.), and
continuing for a period of one (1) year: (a) its products (excluding any software) will be free from material defects in materials and workmanship
under normal use; and (b) the software provided in connection with its products, including any software contained or embedded in such products
will substantially conform to Barracuda Networks published specifications in effect as of the date of manufacture. Except for the foregoing, the
software is provided as is. In no event does Barracuda Networks warrant that the software is error free or that Customer will be able to operate
the software without problems or interruptions. In addition, due to the continual development of new techniques for intruding upon and attacking
networks, Barracuda Networks does not warrant that the software or any equipment, system or network on which the software is used will be free
of vulnerability to intrusion or attack. The limited warranty extends only to you the original buyer of the Barracuda Networks product and is
non-transferable.
Exclusive Remedy
Your sole and exclusive remedy and the entire liability of Barracuda Networks under this limited warranty shall be, at Barracuda Networks or its
service centers option and expense, the repair, replacement or refund of the purchase price of any products sold which do not comply with this
warranty. Hardware replaced under the terms of this limited warranty may be refurbished or new equipment substituted at Barracuda Networks
option. Barracuda Networks obligations hereunder are conditioned upon the return of affected articles in accordance with Barracuda Networks
then-current Return Material Authorization (“RMA”) procedures. All parts will be new or refurbished, at Barracuda Networks discretion, and shall
be furnished on an exchange basis. All parts removed for replacement will become the property of the Barracuda Networks. In connection with
warranty services hereunder, Barracuda Networks may at its discretion modify the hardware of the product at no cost to you to improve its
reliability or performance. The warranty period is not extended if Barracuda Networks repairs or replaces a warranted product or any parts.
Barracuda Networks may change the availability of limited warranties, at its discretion, but any changes will not be retroactive. IN NO EVENT
SHALL BARRACUDA NETWORKS LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE, OR
ITS DOCUMENTATION.
Exclusions and Restrictions
This limited warranty does not apply to Barracuda Networks products that are or have been (a) marked or identified as “sample” or “beta,” (b)
loaned or provided to you at no cost, (c) sold “as is,” (d) repaired, altered or modified except by Barracuda Networks, (e) not installed, operated or
maintained in accordance with instructions supplied by Barracuda Networks, or (f) subjected to abnormal physical or electrical stress, misuse,
negligence or to an accident.
EXCEPT FOR THE ABOVE WARRANTY, BARRACUDA NETWORKS MAKES NO OTHER WARRANTY, EXPRESS, IMPLIED OR
STATUTORY, WITH RESPECT TO BARRACUDA NETWORKS PRODUCTS, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY
OF TITLE, AVAILABILITY, RELIABILITY, USEFULNESS, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE,
NONINFRINGEMENT, OR ARISING FROM COURSE OF PERFORMANCE, DEALING, USAGE OR TRADE. EXCEPT FOR THE ABOVE
WARRANTY, BARRACUDA NETWORKS PRODUCTS AND THE SOFTWARE IS PROVIDED “AS IS” AND BARRACUDA NETWORKS DOES
NOT WARRANT THAT ITS PRODUCTS WILL MEET YOUR REQUIREMENTS OR BE UNINTERRUPTED, TIMELY, AVAILABLE, SECURE OR
ERROR-FREE, OR THAT ANY ERRORS IN ITS PRODUCTS OR THE SOFTWARE WILL BE CORRECTED. FURTHERMORE, BARRACUDA
NETWORKS DOES NOT WARRANT THAT BARRACUDA NETWORKS PRODUCTS, THE SOFTWARE OR ANY EQUIPMENT, SYSTEM OR
NETWORK ON WHICH BARRACUDA NETWORKS PRODUCTS WILL BE USED WILL BE FREE OF VULNERABILITY TO INTRUSION OR
ATTACK.
Software License
PLEASE READ THIS SOFTWARE LICENSE AGREEMENT (“AGREEMENT”) CAREFULLY BEFORE USING THE BARRACUDA SOFTWARE.
BY USING THE BARRACUDA SOFTWARE YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE. IF YOU DO NOT
AGREE TO THE TERMS OF THIS LICENSE DO NOT USE THE SOFTWARE. IF YOU DO NOT AGREE TO THE TERMS OF THIS LICENSE
YOU MAY RETURN THE SOFTWARE OR HARDWARE CONTAINING THE SOFTWARE FOR A FULL REFUND TO YOUR PLACE OF
PURCHASE.
1. The software, documentation, whether on disk, in read only memory, or on any other media or in any other form (collectively “Barracuda
Software”) is licensed, not sold, to you by Barracuda Networks, Inc. (“Barracuda”) for use only under the terms of this License and Barracuda
reserves all rights not expressly granted to you. The rights granted are limited to Barracuda's intellectual property rights in the Barracuda
Software and do not include any other patent or intellectual property rights. You own the media on which the Barracuda Software is recorded but
Barracuda retains ownership of the Barracuda Software itself.
2. Permitted License Uses and Restrictions. This License allows you to use the Software only on the single Barracuda labeled hardware device
on which the software was delivered. You may not make copies of the Software and you may not make the Software available over a network
321
where it could be utilized by multiple devices or copied. You may not make a backup copy of the Software. You may not modify or create
derivative works of the Software except as provided by the Open Source Licenses included below. The BARRACUDA SOFTWARE IS NOT
INTENDED FOR USE IN THE OPERATION OF NUCLEAR FACILITIES, AIRCRAFT NAVIGATION OR COMMUNICATION SYSTEMS, LIFE
SUPPORT MACHINES, OR OTHER EQUIPEMENT IN WHICH FAILURE COULD LEAD TO DEATH, PERSONAL INJURY, OR
ENVIRONMENTAL DAMAGE.
3. You may not transfer, rent, lease, lend, or sublicense the Barracuda Software.
4. This License is effective until terminated. This License is automatically terminated without notice if you fail to comply with any term of the
License. Upon termination you must destroy or return all copies of the Barracuda Software.
5. YOU EXPRESSLY ACKNOWLEDGE AND AGREE THAT THE USE OF THE BARRACUDA SOFTWARE IS AT YOUR OWN RISK AND THAT
THE ENTIRE RISK AS TO SATISFACTION, QUALITY, PERFORMANCE, AND ACCURACY IS WITH YOU. THE BARRACUDA SOFTWARE IS
PROVIDED “AS IS” WITH ALL FAULTS AND WITHOUT WARRANTY OF ANY KIND, AND BARRACUDA HEREBY DISCLAIMS ALL
WARRANTIES AND CONDITIONS WITH RESPECT TO THE BARRACUDA SOFTWARE, EITHER EXPRESSED OR IMPLIED OR
STATUTORY, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES AND/OR CONDITIONS OF MERCHANTIBILITY, OF
SATISFACTORY QUALITY, OF FITNESS FOR ANY APPLICATION, OF ACCURACY, AND OF NON-INFRINGEMENT OF THIRD PARTY
RIGHTS. BARRACUDA DOES NOT WARRANT THE CONTINUED OPERATION OF THE SOFTWARE, THAT THE PERFORMANCE WILL
MEET YOUR EXPECTATIONS, THAT THE FUNCTIONS WILL MEET YOUR REQUIREMENTS, THAT THE OPERATION WILL BE ERROR
FREE OR CONTINUOUS, OR THAT DEFECTS WILL BE CORRECTED. NO ORAL OR WRITTEN INFORMATION GIVEN BY BARRACUDA
OR AUTHORIZED BARRACUDA REPRESENTATIVE SHALL CREATE A WARRANTY. SHOULD THE BARRACUDA SOFTWARE PROVE
DEFECTIVE, YOU ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR, OR CORRECTION.
6. License. YOU EXPRESSLY ACKNOWLEDGE AND AGREE THAT YOU WILL PROVIDE AN UNLIMITED ZERO COST LICENSE TO
BARRACUDA FOR ANY PATENTS OR OTHER INTELLECTUAL PROPERTY RIGHTS UTILIZED IN THE BARRACUDA SOFTWARE WHICH
YOU EITHER OWN OR CONTROL.
7. Limitation of Liability. TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT SHALL BARRACUDA BE LIABLE FOR PERSONAL
INJURY OR ANY INCIDENTAL SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES WHATSOEVER, INCLUDING, WITHOUT
LIMITATION, DAMAGES FOR LOSS OF PROFITS, LOSS OF DATA, BUSINESS INTERRUPTION, OR ANY OTHER COMMERCIAL
DAMAGES OR LOSSES, ARISING OUT OF OR RELATED TO YOUR ABILITY TO USE OR INABILITY TO USE THE BARRACUDA
SOFTWARE HOWEVER CAUSED, REGARDLESS OF THE THEORY OF LIABILITY AND EVEN IF BARRACUDA HAS BEEN ADVISED OF
THE POSSIBILITY OF DAMAGES. In no event shall Barracuda's total liability to you for all damages exceed the amount of one hundred dollars.
8. Export Control. You may not use or otherwise export or re-export Barracuda Software except as authorized by the United States law and the
laws of the jurisdiction where the Barracuda Software was obtained.
Energize Update Software License
PLEASE READ THIS ENERGIZE UPDATE SOFTWARE LICENSE CAREFULLY BEFORE DOWNLOADING, INSTALLING OR USING
BARRACUDA NETWORKS OR BARRACUDA NETWORKS-SUPPLIED ENERGIZE UPDATE SOFTWARE.
BY DOWNLOADING OR INSTALLING THE ENERGIZE UPDATE SOFTWARE, OR USING THE EQUIPMENT THAT CONTAINS THIS
SOFTWARE, YOU ARE CONSENTING TO BE BOUND BY THIS LICENSE. IF YOU DO NOT AGREE TO ALL OF THE TERMS OF THIS
LICENSE, THEN (A) DO NOT DOWNLOAD, INSTALL OR USE THE SOFTWARE, AND (B) YOU MAY RETURN THE SOFTWARE FOR A FULL
REFUND, OR, IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER PRODUCT, YOU MAY RETURN THE ENTIRE PRODUCT FOR A
FULL REFUND. YOUR RIGHT TO RETURN AND REFUND EXPIRES 30 DAYS AFTER PURCHASE FROM BARRACUDA NETWORKS OR AN
AUTHORIZED BARRACUDA NETWORKS RESELLER, AND APPLIES ONLY IF YOU ARE THE ORIGINAL PURCHASER.
The following terms govern your use of the Energize Update Software except to the extent a particular program (a) is the subject of a separate
written agreement with Barracuda Networks or (b) includes a separate “click-on” license agreement as part of the installation and/or download
process. To the extent of a conflict between the provisions of the foregoing documents, the order of precedence shall be (1) the written
agreement, (2) the click-on agreement, and (3) this Energize Update Software License.
License. Subject to the terms and conditions of and except as otherwise provided in this Agreement, Barracuda Networks, Inc., or a Barracuda
Networks, Inc. subsidiary (collectively “Barracuda Networks”), grants to the end-user (“Customer”) a nonexclusive and nontransferable license to
use the Barracuda Networks Energize Update program modules and data files for which Customer has paid the required license fees (the
“Energize Update Software”). In addition, the foregoing license shall also be subject to the following limitations, as applicable:
Unless otherwise expressly provided in the documentation, Customer shall use the Energize Update Software solely as embedded in, for
execution on, or (where the applicable documentation permits installation on non-Barracuda Networks equipment) for communication with
Barracuda Networks equipment owned or leased by Customer; Customer's use of the Energize Update Software shall be limited to use on a
single hardware chassis, on a single central processing unit, as applicable, or use on such greater number of chassis or central processing units
as Customer may have paid Barracuda Networks the required license fee; and Customer's use of the Energize Update Software shall also be
limited, as applicable and set forth in Customer's purchase order or in Barracuda Networks' product catalog, user documentation, or web site, to a
maximum number of (a) seats (i.e. users with access to the installed Energize Update Software), (b) concurrent users, sessions, ports, and/or
issued and outstanding IP addresses, and/or (c) central processing unit cycles or instructions per second. Customer's use of the Energize Update
Software shall also be limited by any other restrictions set forth in Customer's purchase order or in Barracuda Networks' product catalog, user
documentation or web site for the Energize Update Software.
322
General Limitations. Except as otherwise expressly provided under this Agreement, Customer shall have no right, and Customer specifically
agrees not to:
i. transfer, assign or sublicense its license rights to any other person, or use the Energize Update Software on
unauthorized or secondhand Barracuda Networks equipment, and any such attempted transfer, assignment or
sublicense shall be void;
ii. make error corrections to or otherwise modify or adapt the Energize Update Software or create derivative works based
upon the Energize Update Software, or to permit third parties to do the same; or
iii. decompile, decrypt, reverse engineer, disassemble or otherwise reduce the Energize Update Software to
human-readable form to gain access to trade secrets or confidential information in the Energize Update Software.
Upgrades and Additional Copies. For purposes of this Agreement, “Energize Update Software” shall include (and the terms and conditions of this
Agreement shall apply to) any Energize Update upgrades, updates, bug fixes or modified versions (collectively, “Upgrades”) or backup copies of
the Energize Update Software licensed or provided to Customer by Barracuda Networks or an authorized distributor/reseller for which Customer
has paid the applicable license fees. NOTWITHSTANDING ANY OTHER PROVISION OF THIS AGREEMENT: (1) CUSTOMER HAS NO
LICENSE OR RIGHT TO USE ANY SUCH ADDITIONAL COPIES OR UPGRADES UNLESS CUSTOMER, AT THE TIME OF ACQUIRING
SUCH COPY OR UPGRADE, ALREADY HOLDS A VALID LICENSE TO THE ORIGINAL ENERGIZE UPDATE SOFTWARE AND HAS PAID
THE APPLICABLE FEE FOR THE UPGRADE; (2) USE OF UPGRADES IS LIMITED TO BARRACUDA NETWORKS EQUIPMENT FOR WHICH
CUSTOMER IS THE ORIGINAL END USER PURCHASER OR LESSEE OR WHO OTHERWISE HOLDS A VALID LICENSE TO USE THE
ENERGIZE UPDATE SOFTWARE WHICH IS BEING UPGRADED; AND (3) USE OF ADDITIONAL COPIES IS LIMITED TO BACKUP
PURPOSES ONLY.
Energize Update Changes. Barracuda Networks reserves the right at any time not to release or to discontinue release of any Energize Update
Software and to alter prices, features, specifications, capabilities, functions, licensing terms, release dates, general availability or other
characteristics of any future releases of the Energize Update Software.
Proprietary Notices. Customer agrees to maintain and reproduce all copyright and other proprietary notices on all copies, in any form, of the
Energize Update Software in the same form and manner that such copyright and other proprietary notices are included on the Energize Update
Software. Except as expressly authorized in this Agreement, Customer shall not make any copies or duplicates of any Energize Update Software
without the prior written permission of Barracuda Networks. Customer may make such backup copies of the Energize Update Software as may be
necessary for Customer's lawful use, provided Customer affixes to such copies all copyright, confidentiality, and proprietary notices that appear
on the original.
Protection of Information. Customer agrees that aspects of the Energize Update Software and associated documentation, including the specific
design and structure of individual programs, constitute trade secrets and/or copyrighted material of Barracuda Networks. Customer shall not
disclose, provide, or otherwise make available such trade secrets or copyrighted material in any form to any third party without the prior written
consent of Barracuda Networks. Customer shall implement reasonable security measures to protect and maintain the confidentiality of such trade
secrets and copyrighted material. Title to Energize Update Software and documentation shall remain solely with Barracuda Networks.
Indemnity. Customer agrees to indemnify, hold harmless and defend Barracuda Networks and its affiliates, subsidiaries, officers, directors,
employees and agents at Customers expense, against any and all third-party claims, actions, proceedings, and suits and all related liabilities,
damages, settlements, penalties, fines, costs and expenses (including, without limitation, reasonable attorneys fees and other dispute resolution
expenses) incurred by Barracuda Networks arising out of or relating to Customers (a) violation or breach of any term of this Agreement or any
policy or guidelines referenced herein, or (b) use or misuse of the Barracuda Networks Energize Update Software.
Term and Termination. This License is effective upon date of delivery to Customer of the initial Energize Update Software (but in case of resale
by a Barracuda Networks distributor or reseller, commencing not more than sixty (60) days after original Energize Update Software purchase
from Barracuda Networks) and continues for the period for which Customer has paid the required license fees. Customer may terminate this
License at any time by notifying Barracuda Networks and ceasing all use of the Energize Update Software. By terminating this License, Customer
forfeits any refund of license fees paid and is responsible for paying any and all outstanding invoices. Customer's rights under this License will
terminate immediately without notice from Barracuda Networks if Customer fails to comply with any provision of this License. Upon termination,
Customer must cease use of all copies of Energize Update Software in its possession or control.
Export. Software, including technical data, may be subject to U.S. export control laws, including the U.S. Export Administration Act and its
associated regulations, and may be subject to export or import regulations in other countries. Customer agrees to comply strictly with all such
regulations and acknowledges that it has the responsibility to obtain licenses to export, re-export, or import Energize Update Software.
Restricted Rights. Barracuda Networks' commercial software and commercial computer software documentation is provided to United States
Government agencies in accordance with the terms of this Agreement, and per subparagraph “(c)” of the “Commercial Computer Software Restricted Rights” clause at FAR 52.227-19 (June 1987). For DOD agencies, the restrictions set forth in the “Technical Data-Commercial Items”
clause at DFARS 252.227-7015 (Nov 1995) shall also apply.
No Warranty. The Energize Update Software is provided AS IS. Customer's sole and exclusive remedy and the entire liability of Barracuda
Networks under this Energize Update Software License Agreement will be, at Barracuda Networks option, repair, replacement, or refund of the
Energize Update Software.
Renewal. At the end of the Energize Update Service Period, Customer may have the option to renew the Energize Update Service at the current
list price, provided such Energize Update Service is available. All initial subscriptions commence at the time of sale of the unit and all renewals
commence at the expiration of the previous valid subscription.
323
In no event does Barracuda Networks warrant that the Energize Update Software is error free or that Customer will be able to operate the
Energize Update Software without problems or interruptions. In addition, due to the continual development of new techniques for intruding upon
and attacking networks, Barracuda Networks does not warrant that the Energize Update Software or any equipment, system or network on which
the Energize Update Software is used will be free of vulnerability to intrusion or attack.
DISCLAIMER OF WARRANTY. ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS, AND WARRANTIES INCLUDING,
WITHOUT LIMITATION, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE,
NONINFRINGEMENT, SATISFACTORY QUALITY OR ARISING FROM A COURSE OF DEALING, LAW, USAGE, OR TRADE PRACTICE, ARE
HEREBY EXCLUDED TO THE EXTENT ALLOWED BY APPLICABLE LAW. TO THE EXTENT AN IMPLIED WARRANTY CANNOT BE
EXCLUDED, SUCH WARRANTY IS LIMITED IN DURATION TO THE WARRANTY PERIOD. BECAUSE SOME STATES OR JURISDICTIONS
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
JURISDICTION TO JURISDICTION.
General Terms Applicable to the Energize Update Software License Disclaimer of Liabilities. IN NO EVENT WILL BARRACUDA NETWORKS BE
LIABLE FOR ANY LOST REVENUE, PROFIT, OR DATA, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR PUNITIVE
DAMAGES HOWEVER CAUSED AND REGARDLESS OF THE THEORY OF LIABILITY ARISING OUT OF THE USE OF OR INABILITY TO
USE THE ENERGIZE UPDATE SOFTWARE EVEN IF BARRACUDA NETWORKS OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. In no event shall Barracuda Networks' liability to Customer, whether in contract, tort (including negligence),
or otherwise, exceed the price paid by Customer. BECAUSE SOME STATES OR JURISDICTIONS DO NOT ALLOW LIMITATION OR
EXCLUSION OF CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
This Energize Update Software License shall be governed by and construed in accordance with the laws of the State of California, without
reference to principles of conflict of laws, provided that for Customers located in a member state of the European Union, Norway or Switzerland,
English law shall apply. The United Nations Convention on the International Sale of Goods shall not apply. If any portion hereof is found to be
void or unenforceable, the remaining provisions of the Energize Update Software License shall remain in full force and effect. Except as expressly
provided herein, the Energize Update Software License constitutes the entire agreement between the parties with respect to the license of the
Energize Update Software and supersedes any conflicting or additional terms contained in the purchase order.
Open Source Licensing
Barracuda products may include programs that are covered by the GNU General Public License (GPL) or other “open source” license
agreements. The GNU license is re-printed below for you reference. These programs are copyrighted by their authors or other parties, and the
authors and copyright holders disclaim any warranty for such programs. Other programs are copyright by Barracuda Networks.
GNU GENERAL PUBLIC LICENSE, (GPL) Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public
License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General
Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some
other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have
the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it,
that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These
restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whethergratis or for a fee, you must give the recipients all the rights that you have. You
must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute
and/or modify the software.
Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If
the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any
problems introduced by others will not reflect on the original authors' reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will
individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be
licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
324
GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under
the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means
either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or
with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each
licensee is addressed as "you".
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the
Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of
having been made by running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously
and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this
License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute
such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part
thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive
use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no
warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the
user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement,
your work based on the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be
reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you
distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the
distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each
and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right
to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of
a storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of
Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1
and 2 above on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically
performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of
Sections 1 and 2 above on a medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only
for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with
Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code
means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and
installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed
(in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs,
unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy
the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source
along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to
copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who
have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full
compliance.
325
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute
the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing
the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for
copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original
licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the
recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions
are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from
the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent
obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free
redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this
License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and
the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this
section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices.
Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent
application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a
licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original
copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so
that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the
body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions
will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and "any later
version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software
Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software
Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask
for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make
exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of
promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK
AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU
ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free
software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the
exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found.
one line to give the program's name and an idea of what it does.
326
Copyright (C) yyyy name of author
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the
Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc.,
59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) 19yy name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'.
This is free software, and you are welcome to redistribute it under certain conditions; type `show c' for details.
The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License. Of course, the commands
you use may be called something other than `show w' and `show c'; they could even be mouse-clicks or menu items--whatever suits your
program.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the program, if
necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision' (which makes passes at compilers) written by James
Hacker.
signature of Ty Coon, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you
may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Library General
Public License instead of this License.
Barracuda Products may contain programs that are copyright (c)1995-2005 International Business Machines Corporation and others. All rights
reserved. These programs are covered by the following License:
"Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the
"Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute,
and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, provided that the above copyright notice(s)
and this permission notice appear in all copies of the Software and that both the above copyright notice(s) and this permission notice appear in
supporting documentation."
Barracuda Products may include programs that are covered by the BSD License: "Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the following conditions are met:
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
The names of the authors may not be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE."
Barracuda Products may include the libspf library which is Copyright (c) 2004 James Couzens & Sean Comeau All rights reserved. It is covered
by the following agreement: Redistribution and use in source and binary forms, with or without modification, are permitted provided that the
following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following
disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESSED OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHORS MAKING USE OF THIS LICENSE OR ITS
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Barracuda Products may contain programs that are Copyright (c) 1998-2003 Carnegie Mellon University. All rights reserved. Redistribution and
use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of
source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must
327
reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with
the distribution. The name "Carnegie Mellon University" must not be used to endorse or promote products derived from this software without prior
written permission. For permission or any other legal details, please contact Office of Technology Transfer Carnegie Mellon University 5000
Forbes Avenue Pittsburgh, PA 15213-3890 (412) 268-4387, fax: (412) 268-7395 [email protected] .Redistributions of any form
whatsoever must retain the following acknowledgment: "This product includes software developed by Computing Services at Carnegie Mellon
University (http://www.cmu.edu/computing/)." CARNEGIE MELLON UNIVERSITY DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS
SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL CARNEGIE MELLON
UNIVERSITY BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS
ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
Barracuda products may include programs that are covered by the Apache License or other Open Source license agreements. The Apache
license is re-printed below for you reference. These programs are copyrighted by their authors or other parties, and the authors and copyright
holders disclaim any warranty for such programs. Other programs are copyright by Barracuda Networks.
Apache License
Version 2.0, January 2004
http://www.apache.org/licenses/
TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION
1. Definitions.
"License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document.
"Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the License.
"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that
entity. For the purposes of this definition, "control" means (i) the power, direct or indirect, to cause the direction or management of such entity,
whether by contract or otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such
entity.
"You" (or "Your") shall mean an individual or Legal Entity exercising permissions granted by this License.
"Source" form shall mean the preferred form for making modifications, including but not limited to software source code, documentation source,
and configuration files.
"Object" form shall mean any form resulting from mechanical transformation or translation of a Source form, including but not limited to compiled
object code, generated documentation, and conversions to other media types.
"Work" shall mean the work of authorship, whether in Source or Object form, made available under the License, as indicated by a copyright notice
that is included in or attached to the work (an example is provided in the Appendix below).
"Derivative Works" shall mean any work, whether in Source or Object form, that is based on (or derived from) the Work and for which the editorial
revisions, annotations, elaborations, or other modifications represent, as a whole, an original work of authorship. For the purposes of this License,
Derivative Works shall not include works that remain separable from, or merely link (or bind by name) to the interfaces of, the Work and
Derivative Works thereof.
"Contribution" shall mean any work of authorship, including the original version of the Work and any modifications or additions to that Work or
Derivative Works thereof, that is intentionally submitted to Licensor for inclusion in the Work by the copyright owner or by an individual or Legal
Entity authorized to submit on behalf of the copyright owner. For the purposes of this definition, "submitted" means any form of electronic, verbal,
or written communication sent to the Licensor or its representatives, including but not limited to communication on electronic mailing lists, source
code control systems, and issue tracking systems that are managed by, or on behalf of, the Licensor for the purpose of discussing and improving
the Work, but excluding communication that is conspicuously marked or otherwise designated in writing by the copyright owner as "Not a
Contribution."
"Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a Contribution has been received by Licensor and
subsequently incorporated within the Work.
2. Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide,
non-exclusive, no-charge, royalty-free, irrevocable copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform,
sublicense, and distribute the Work and such Derivative Works in Source or Object form.
3. Grant of Patent License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide,
non-exclusive, no-charge, royalty-free, irrevocable (except as stated in this section) patent license to make, have made, use, offer to sell, sell,
import, and otherwise transfer the Work, where such license applies only to those patent claims licensable by such Contributor that are
necessarily infringed by their Contribution(s) alone or by combination of their Contribution(s) with the Work to which such Contribution(s) was
submitted. If You institute patent litigation against any entity (including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a
Contribution incorporated within the Work constitutes direct or contributory patent infringement, then any patent licenses granted to You under
this License for that Work shall terminate as of the date such litigation is filed.
4. Redistribution. You may reproduce and distribute copies of the Work or Derivative Works thereof in any medium, with or without modifications,
328
and in Source or Object form, provided that You meet the following conditions:
(a) You must give any other recipients of the Work or Derivative Works a copy of this License; and
(b) You must cause any modified files to carry prominent notices stating that You changed the files; and
(c) You must retain, in the Source form of any Derivative Works that You distribute, all copyright, patent, trademark, and attribution notices from
the Source form of the Work, excluding those notices that do not pertain to any part of the Derivative Works; and
(d) If the Work includes a "NOTICE" text file as part of its distribution, then any Derivative Works that You distribute must include a readable copy
of the attribution notices contained within such NOTICE file, excluding those notices that do not pertain to any part of the Derivative Works, in at
least one of the following places: within a NOTICE text file distributed as part of the Derivative Works; within the Source form or documentation, if
provided along with the Derivative Works; or, within a display generated by the Derivative Works, if and wherever such third-party notices
normally appear. The contents of the NOTICE file are for informational purposes only and do not modify the License.
You may add Your own attribution notices within Derivative Works that You distribute, alongside or as an addendum to the NOTICE text from the
Work, provided that such additional attribution notices cannot be construed as modifying the License.
You may add Your own copyright statement to Your modifications and may provide additional or different license terms and conditions for use,
reproduction, or distribution of Your modifications, or for any such Derivative Works as a whole, provided Your use, reproduction, and distribution
of the Work otherwise complies with the conditions stated in this License.
5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to
the Licensor shall be under the terms and conditions of this License, without any additional terms or conditions. Notwithstanding the above,
nothing herein shall supersede or modify the terms of any separate license agreement you may have executed with Licensor regarding such
Contributions.
6. Trademarks. This License does not grant permission to use the trade names, trademarks, service marks, or product names of the Licensor,
except as required for reasonable and customary use in describing the origin of the Work and reproducing the content of the NOTICE file.
7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides the Work (and each Contributor provides
its Contributions) on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without
limitation, any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE.
You are solely responsible for determining the appropriateness of using or redistributing the Work and assume any risks associated with Your
exercise of permissions under this License.
8. Limitation of Liability. In no event and under no legal theory, whether in tort (including negligence), contract, or otherwise, unless required by
applicable law (such as deliberate and grossly negligent acts) or agreed to in writing, shall any Contributor be liable to You for damages, including
any direct, indirect, special, incidental, or consequential damages of any character arising as a result of this License or out of the use or inability
to use the Work (including but not limited to damages for loss of goodwill, work stoppage, computer failure or malfunction, or any and all other
commercial damages or losses), even if such Contributor has been advised of the possibility of such damages.
9. Accepting Warranty or Additional Liability. While redistributing the Work or Derivative Works thereof, You may choose to offer, and charge a
fee for, acceptance of support, warranty, indemnity, or other liability obligations and/or rights consistent with this License. However, in accepting
such obligations, You may act only on Your own behalf and on Your sole responsibility, not on behalf of any other Contributor, and only if You
agree to indemnify, defend, and hold each Contributor harmless for any liability incurred by, or claims asserted against, such Contributor by
reason of your accepting any such warranty or additional liability.
END OF TERMS AND CONDITIONS
APPENDIX: How to apply the Apache License to your work.
To apply the Apache License to your work, attach the following boilerplate notice, with the fields enclosed by brackets "[]" replaced with your own
identifying information. (Don't include the brackets!) The text should be enclosed in the appropriate comment syntax for the file format. We also
recommend that a file or class name and description of purpose be included on the same "printed page" as the copyright notice for easier
identification within third-party archives.
Copyright [yyyy] [name of copyright owner]
Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain
a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and
limitations under the License.
Source Code Availability
Per the GPL and other “open source” license agreements the complete machine readable source code for programs covered by the GPL or other
“open source” license agreements is available from Barracuda Networks at no charge. If you would like a copy of the source code or the changes
to a particular program we will gladly provide them, on a CD, for a fee of $100.00. This fee is to pay for the time for a Barracuda Networks
329
engineer to assemble the changes and source code, create the media, package the media, and mail the media. Please send a check payable in
USA funds and include the program name. We mail the packaged source code for any program covered under the GPL or other "open source"
license.

1. Barracuda Spam Firewall - Overview

Transcription

Similar documents

barracuda message archiver

Why Email?

The Premier Tribute to The Rock Band Heart!

AppRiver guards your inbox against unwanted

Legally compliant email management

What We Saw in February

Preparing your Domain to transfer from GoDaddy - Your-Site

Malware at a glance or: Facing the latest threats

NEW FERGUS Magaluf Resort