Solar Powered Motion Sensor Light

®
TM
Solar Powered
Motion Sensor Light
Model: SH-9101AU
Installation and Operating Instructions
FEATURES
•Automatically comes on when motion is detected.
•Automatically turns light off.
•Photocell keeps the light off during daylight
hours.
•LED indicates motion was sensed (day or
night).
•Battery Protection Circuitry. Unit will shut
down when battery is low. Unit will automatically
resume operation when battery is recharged to
a safe level.
UNPACKING
Be sure to remove all contents from packaging
and verify all items are present before assembling
this light fixture. This package includes the following items:
•LED Solar Security Light with Mounting
Screws (x2)
•Solar Panel with Mounting Screws (x3)
•Thumbscrew
•Owner’s Manual
Note: Illustrations are for reference only and may
be different from actual product
Before installation, record the model number listed inside the fixture. Attach receipt
in case of possible warranty issues.
Model Number:
© 2011 The Chamberlain Group, Inc
INITIAL BATTERY CHARGE
The solar panel requires full, direct sunlight
to charge the battery. Clouds, rain, snow, and
other weather conditions may not allow the
solar panel to completely recharge the battery. Other obstructions such as buildings
or trees may block the sun as well.
When installing the solar panel, make sure it
is aimed as described below with a minimum
amount of obstructions. If possible, mount
the panel facing toward the southern sky.
•PRIOR TO USE, the battery will require 3 to
7 days of full sun to completely charge with the
ON-TIME switch in the OFF position. Plug
the solar panel cable into the bottom of the battery
case. If possible, aim the solar panel toward the
south and tilt it approximately 50° from horizontal
(see illustration on next page). If the solar panel
cannot be aimed toward the south, then tilt the
panel approximately 30° if possible.
•To verify battery is charged, slide the ON-TIME
switch to TEST. Wait 2 minutes for sensor to
warm up. If light comes on when motion is detected after warm up period, battery is charged
and ready for use. If light does not come on, slide
the ON-TIME to OFF. Recheck the light the
next day.
•Actual operating time will vary depending upon
how frequently the light is turned on by the motion sensor and amount of sunlight collected.
•Solar lighting is not designed to equal standard
120V lighting. The amount of light output is
reduced to allow the sun time to fully recharge
the battery between lighting cycles.
201116-01A
IMPORTANT SAFETY AND INSTALLATION INFORMATION
Before installing security light, read all instructions carefully and keep owner’s manual for future
reference.
•To achieve best results, this fixture should be mounted 2.4 meters (8 feet) above the ground. Note: If fixture
is mounted higher than 2.4 meters (8 feet), aiming the sensor down will reduce coverage distance.
The sensor on this light fixture detects “motion” by the movement of heat across the coverage area. However, following are examples of objects that also produce heat and can cause the sensor to trigger:
• Pools of Water
• Air Conditioners
• Dryer Vents
• Animals
• Heating Vents
• Automobile Traffic
If you suspect that a heat source of this type is triggering the sensor, reduce the sensitivity.
The sensor on this fixture is more sensitive to the movement of heat moving across the coverage area
and less sensitive to the movement of heat directly towards it.
Motion
Motion
Sensor
Least Sensitive
Wall Mount
Most Sensitive
Do NOT Eave Mount
Note: Light fixture and sensor should be mounted as shown above when installed (depending upon
type of installation).
201116-01
2
INSTALLATION
Angled 50°
For best performance, mount the fixture about 2.4
meters (8 feet) above the ground. For best solar
collection, mount the solar panel on a southern
facing surface. Note: If fixture is mounted higher
than 2.4 meters (8 feet), aiming the sensor down
will reduce coverage distance.
1. Install Solar Panel Thumbscrew. Remove
thumbscrew from hardware package and
carefully thread into bottom of solar panel as
shown.
Roof Mount
Wall Mount
S
N
E
W
Angled 50°
Note: Solar panel should be mounted as shown
above when installed (depending upon type of
installation).
After adjusting solar panel, tighten the thumbscrew
on the bottom of the solar panel.
Mounted Solar Panel
3. Mount Light Fixture. Attach the battery case
to a solid surface using two round-head screws
and the keyholes on the back of the case.
Note: Use the included mounting template to
help mark the mounting hole locations.
Thumbscrew
Install Thumbscrew into Solar Panel
2. Mount Solar Panel. Allow for enough wire
to reach the battery case. Attach triangular
base to a solid surface using three tapered
screws. IMPORTANT: Caulk around the base
and on top of the tapered screw heads after
installation.
Note: See Initial Battery Charge and illustration
on next page for solar panel setup information.
146 mm
(5 3/4")
Mounting
Holes (2)
Solar Panel
Caulk All Mounting
Holes (3)
Caulk Base Edges
Solar Panel
Wire
Ball Joint
Light Fixture
Three Mounting Holes for Solar Panel Base
201116-01
3
Wall Mounted Light
5. Plug the solar panel cable into the bottom
of the battery case. IMPORTANT: Allow the
battery to charge with 3 to 7 days of full
sunshine before testing. To verify battery
is charged, slide the ON-TIME switch to
TEST. Wait 2 minutes for sensor to warm
up. If light comes on when motion is detected after warm up period, battery is
charged and ready for use. If light does
not come on, slide the ON-TIME to OFF.
Recheck the light the next day.
Note: Light fixture and sensor should be mounted as
shown above when installed (depending upon type
of installation).
TEST AND ADJUSTMENT
Do Not Mount Under Eaves
NOTE: Sensor has a 2 minute warm up period
before it will detect motion. When switching
modes wait 2 minutes.
4. Adjust sensor. For proper operation, the sensor head must be rotated so that the sensor
controls face downward as shown below.
1. Slide the sensor switch to the TEST position.
2. Place the RANGE adjustment in the medium
position (halfway between MIN and MAX
position).
IMPORTANT: The controls must face downward to avoid damage from rain. If controls
face upward, move sensor to the original down
position, rotate 180°, then raise to the position
shown below.
Red LED Indicator
ON-TIME
Light Joint Clamps
TEST 1 5 OFF
MINUTES
RANGE
MIN
MAX
Light
Battery Case
Bottom of Sensor
Sensor
3. Loosen the clamp screw in the sensor ball
joint.
Lens Removal
Tab
Ball Joint
Sensor Joint
Clamp
Clamp Screw
Controls
4
201116-01
OPERATION
4. Walk through the coverage area noting when
the lights turn on. Gently move the sensor head
up, down, or sideways to change the coverage
area. Note: Wait 5 to 10 seconds after light
turns off to retest.
Place the sensor switch in the 1 or 5 minute mode
for normal operation. If the light is not needed,
put the switch in the OFF position.
Mode:
Test
Auto
Aim Sensor Down for
Short Coverage
Aim Sensor Higher for
Long Coverage
Works: Day Night
x
x
x
THINGS TO REMEMBER
• Periodically clean the solar panel with a soft
cloth and warm water. Do not hose spray. Keep
the collector clear of snow and leaves. Make sure
trees and other objects do not block sunlight
from the panel.
•If not to be used for several weeks, turn the unit
OFF. Store it with the panel connected and
where the panel can gather sunlight.
•Solar collection is only effective in direct sunlight.
Every hour the light is on requires a minimum
of 16 hours of sunlight charging. Solar panels
collect less than 10% of the sun’s energy.
•Several days of use with overcast skies may
discharge the battery. Because of the battery
protection circuit, the light will not work until
the battery is sufficiently recharged. Note: To
determine if the battery is charged after the initial
setup, watch the red LED on the front of the
sensor. If it blinks when motion is sensed, then
the battery is charged. If not, then turn the ONTIME switch to off and allow the sun to charge
the battery for 3 to 7 days. Test the battery as
described under Initial Battery Charge, page 1.
•This light is supplied with three permanent
LED lamps. The LED’s are rated to provide a
minimum of 40,000 hours of light output and
do not need to be replaced.
180°
2.4 m
(8 ft.)
21 m
(70 ft.)
Maximum
Maximum Range
Coverage Angle*
(Side View)
(Top View)
5. Increase RANGE only as needed. A higher
RANGE setting may cause false triggering and
reduce battery life.
6. Secure the sensor into position by tightening the clamp screw. Do not overtighten the
screw.
7. After dark, loosen the light joint clamps and
adjust the light to cover desired area. Tighten
joint clamps when desired area is covered.
201116-01
On-Time
5 Seconds
1 or 5
Minutes
5
BATTERY REPLACEMENT
IMPORTANT: Keep sensor switch in the“OFF”
position for 3 to 7 days to allow the battery
to fully charge before testing.
This solar light contains a rechargeable battery that
can be replaced if needed. Rechargeable batteries
will eventually lose their ability to hold a charge.
To replace the battery follow the steps below.
Rechargeable
Battery
IMPORTANT: The sealed lead-acid battery
must be recycled or disposed of properly.
Tab Slots
Positive Wire
Battery
Cover
1. Remove rear battery cover. Press in the two
catch releases on the cover and remove the
cover.
2. Remove rechargeable battery. Slide battery out
of case and remove the wire connectors from
the battery.
3. Replace battery. Connect the RED wire connector to the positive (+) terminal and the
BLACK wire connector to the negative (-)
terminal. Wire connectors should fit tightly.
If not, remove the wire connector from the
terminal. Use a pair of pliers to gently squeeze
the connector to ensure a tight fit. Reconnect
wire connector to the terminal.
4. Replace battery cover. Insert the two tabs on
the cover into the slots on the back of the case.
Press the cover against the case until the two
catch releases snap into place.
Negative Wire
Battery Cover Catch Release
6
201116-01
SPECIFICATIONS
Range�������������������������������������� Up to 21 m (70 ft.) [varies with surrounding temperature]
Sensing Angle������������������������� Up to 180°
LED (x3)��������������������������������� 7.8 Watts
Battery Type���������������������������� Sealed lead acid, 6 V 5.5 A-Hr.
Operating Modes�������������������� TEST and AUTO
ON-Timer������������������������������� OFF, 1 and 5 minutes
Test Timer������������������������������� 5 Seconds
Full Charge On Time�������������� Up to 1 hour
IMPORTANT: DO NOT reverse the battery wires. Damage to the unit will result. Like any leadacid battery, this battery must be disposed of properly.
TROUBLESHOOTING GUIDE
SYMPTOM
Lights will not come on.
POSSIBLE CAUSE
1. Battery is dead.
SOLUTION
2. Sensor is turned OFF.
3. Daylight turn-off is in effect.
4. Incorrect aiming.
1. Switch the sensor OFF and let the battery charge for
3 to 7 sunny days before using again.
2. Turn sensor ON.
3. Recheck after dark.
4. Re-aim the sensor to cover desired area.
Lights come on in daylight.
1. Light control may be installed in a relatively
dark location.
2. Light control is in TEST.
1. Relocate light control to an area that receives more
light.
2. Set control switch to 1 or 5 minute position.
Lights come on for no
apparent reason.
1. Light control may be sensing small animals or
automobile traffic.
2. Range is set too high.
1. Re-aim sensor.
Lights stay on continuously.
1. Light control is pointed toward a heat source
like an air vent, dryer vent, or brightly-colored
heat-reflective surface.
2. Light control is in TEST.
1. Reposition sensor.
Lights flash on and off.
1. Heat or light from the lamp may be turning
the light control on and off.
2. Heat being reflected from other objects may
be affecting the sensor.
3. Light control is in the TEST mode and warming
up.
4. Battery is almost dead.
1. Reposition the lamps away from the sensor.
2. Reduce RANGE.
2. Set control switch to 1 or 5 minute position.
2. Reposition sensor.
3. Flashing is normal under these conditions.
4. Reduce RANGE. If flashing continues, switch the
sensor OFF and let the battery charge for three or
more sunny days before using again.
The Chamberlain Group reserves the right to discontinue products and to change specifications at
any time without incurring any obligation to incorporate new features in products previously sold.
201116-01
7
CHAMBERLAIN LIMITED WARRANTY
Lighting and Chime Products
Chamberlain Australia Pty Limited / Chamberlain New Zealand Limited (Chamberlain) is committed to manufacturing and supplying high quality goods. As
part of this commitment, we seek to provide reliable service and support for our goods and are pleased to provide you, the original purchaser, with this Chamberlain
Limited Warranty.
We also provide the following statement as required by the Australian Consumer Law: In Australia, in addition to your rights under this Chamberlain Limited Warranty, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and
for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
Chamberlain’s warranty
Chamberlain warrants to the original purchaser of the lighting or chime product (including any LED lights which are provided by Chamberlain as part of the goods)
(Unit) that the Unit is free from defects in materials and workmanship for a period of 12 months from the date of purchase.
During the applicable Chamberlain Limited Warranty period, if you are concerned that the Unit may be defective, contact your retailer who will provide you with a
replacement Unit or refer you to our service centre for a factory repair or replacement.
If your retailer refers you to us, call our service centre on the toll free number below and a Chamberlain technician will diagnose the problem. Once the problem has
been diagnosed, subject to your rights under the Australian Consumer Law with respect to major failures, Chamberlain will provide you with shipping instructions
for a factory repair or replacement.
If a factory repair or replacement is required, provided the defective part or Unit is returned to Chamberlain well-packaged and in accordance with Chamberlain’s
shipping instructions, Chamberlain will repair or, at its option but subject to your rights under the Australian Consumer Law with respect to major failures, replace
any defective part or Unit and return it to you at no cost.
Repairs and replacement parts provided under this Chamberlain Limited Warranty are provided free of charge and are warranted for the remaining portion of the
original warranty period.
This Chamberlain Limited Warranty provides benefits which are in addition to your other rights and remedies as a consumer.
Exclusions
If our service centre determines that a warranty claim has been made in respect of a failure or defect arising under or out of any exclusion detailed below such that the
claim is not covered under this Chamberlain Limited Warranty, we may, subject to your other rights and remedies as a consumer, charge you a fee to repair, replace
and/or return the Unit to you.
Exclusions
This Chamberlain Limited Warranty does not cover any failure of, or defect in, the Unit due to:
1. non-compliance with the instructions regarding installation, operation, maintenance and testing of the Unit or of any product with which the Unit is used;
2. any attempt by a person other than an authorised installer to repair, dismantle, reinstall or move the Unit to another location once it has been installed;
3. tampering, neglect, abuse, wear and tear, accident, electrical storm, excessive use or conditions other than normal domestic use;
4. problems caused by electrical faults or replacement of batteries or light bulbs;
5. submersion in water or other fluids;
6. power supply greater or less than what is specified;
7. use of a light bulb with a higher wattage than that specified; or
8. for chimes products, radio interference from another radio frequency appliance.
If this Chamberlain Limited Warranty does not apply, you may have rights available to you under the Australian Consumer Law.
Liability – Australia only
Except as set out in the Australian Consumer Law (being Schedule 2 of the Competition and Consumer Act 2010) (as amended, consolidated or replaced):
1. all other guarantees, warranties and representations in relation to the Unit or its supply are excluded to the extent that Chamberlain can lawfully exclude them;
and
2. under no circumstances will Chamberlain be liable for consequential, incidental or special damages arising in connection with the use, or inability to use, the Unit,
other than those which were reasonably foreseeable as liable to result from the failure.
Liability – New Zealand only
Except as set out in the Fair Trading Act 1986 and the Consumer Guarantees Act 1993 (as amended, consolidated or replaced):
1. all other guarantees, warranties and representations in relation to the Unit or its supply are excluded to the extent that Chamberlain can lawfully exclude them;
and
2. under no circumstances will Chamberlain be liable for consequential, incidental or special damages arising in connection with the use, or inability to use, the Unit,
other than those which were reasonably foreseeable as liable to result from the failure.
Note
We request that you retain your sales docket or invoice as proof-of-purchase and attach it to this manual to enable you to establish the date of purchase in the unlikely
event of a warranty service being required. Chamberlain reserves the right to change the design and specifications of the Unit without prior notification. Some features
or accessories of the Unit may not be available in certain markets or areas. Please check with your retailer.
Chamberlain service centre contact details
Australia
New Zealand
Phone toll free 1800 638 234
Auckland phone 09 477 2823
Fax toll free 1800 888 121
Phone toll free 0800 653 667
Email: [email protected]
Fax toll free 0800 653 663
Chamberlain Australia Pty. Ltd.
Chamberlain New Zealand Limited
Unit 3, 7-9 Orion Rd
17A Arrenway Drive, Albany
Lane Cove NSW 2066
Auckland
(P.O. Box 1446, Lane Cove, NSW 1595)
(PO Box 100221 North Shore 0745)
Website
www.chamberlainanz.com
8
201116-01