MITUTOYO - Micro Precision Calibration

Transcription

Precision Measuring Equipment and Industrial Supplies since 1924.
www.jwdonchin.com
4841 W. Chicago Ave. • Chicago, IL 60651 • Ph: 773.261.2182 • Fax: 773.261.2867 • [email protected]
MITUTOYO - CALIPERS
CALIPERS
Digimatic Calipers w/Absolute Encoders - Series 500 - without SPC output
O-2
Digimatic Calipers w/Absolute Encoders - Series 500
O-3, 4
Digimatic Solar Powered Caliper w/Absolute Encoder - Series 500
O-5, 6
Coolant Proof Digimatic Caliper w/Abs. Enc. (IP-66) - Series 500
O-7
Digimatic Plastic Calipers - Plasti-Cal Series 700, MyCal Lite - Series 700
O-8
Dial Calipers - Series 505
O-9, 10, 11, 12
Digimatic Calipers with Absolute Encoder - Series 550
O-13, 14
Heavy Duty Dial Caliper - Series 504
O-13, 14
Digimatic Snap Calipers w/Absolute Encoders - Series 573
O-15
Digimatic Carbon Fiber Calipers - Series 552
O-16, 17
Digimatic Versa Gage - Series 552
O-18,19
Digimatic Calipers with Absolute Encoder - Series 551
O-20
Digimatic Special Face Calipers with Absolute Encoder - Series 573
O-21, 22
Digimatic Inside Calipers with Absolute Encoder - Series 573
O-23, 24
Offset Calipers - Series 573, 536
O-25, 26
Offset Centerline Calipers - Series 573, 536
O-27
Digimatic Point Calipers with Absolute Encoder - Series 573
O-28
Low Pressure Calipers - Series 573, 536
O-29
How to Read Vernier Calipers
O-30, 31
Precision Vernier Calipers - Series 530, 531, 532
O-32~34
Diamond Master Vernier Calipers - Series 522
O-35
Vernier Calipers - Series 160, 534
O-36, 37
Center Line Gage
O-38
Calipers Depth Base Attachment
O-39
O-02 (2003) full size
12/8/03
9:51 PM
Page 1
CALIPERS
Digimatic Calipers with Absolute Encoder
Series 500 – without SPC output
500-196
Rear view
showing step
measuring
feature.
T
EC
H N OL
Introducing the new Digimatic MyCal E-Z Caliper
featuring ABSOLUTE LINEAR ENCODER technology. It
has achieved superior cost performance and ease of use
by featuring only essential functions.
Features
• The Absolute MyCal E-Z allows direct measurements
from power on. You can forget the time consuming
origin setup which otherwise is required each time the
power is turned on.
• Zero-setting of the display is also possible at any slider
position for easy comparison measurements (incremental mode).
• Large .295" high LCD digits (.365" high LCD digits for
12" Model) allow measurement results to be at a
glance.
Specifications
Inch/Metric (Non-SPC Output Models)
Order No.
500-195
Measuring Range
LCD Resolution
0–4”
.0005”
0–100mm
0.01mm
500-196
0–6”
.0005”
0–150mm
0.01mm
500-159
0–6”
.0005”
0–150mm
0.01mm
500-160
0–6”
.0005”
0–150mm
0.01mm
500-197
0–8”
.0005”
0–200mm
0.01mm
500-163
0–8”
.0005”
0–200mm
0.01mm
500-164
0–8”
.0005”
0–200mm
0.01mm
500-193
0–12”
.0005”
0–300mm
0.01mm
500-165
0–12”
.0005”
0–300mm
0.01mm
500-166
0–12”
.0005”
0–300mm
0.01mm
Replacement Battery: 541980 ( 1 pc.), 541980-10 (10 pcs./SET)
O-2
OG
Y
AB
LUT
SO E
• A scale contamination detection function is implemented to detect contamination of surface and display the
error message (ErrC) on the LCD. The correct value is
only displayed if the contamination is removed.
• The battery life has been greatly extended with the
power-conserving design permitting 3.5 years (20,000
hours) continuous operation with a single battery.
Specifications
Quantizing Error:
Function:
± 1 count
ORIGIN Setting
ZERO/ABS, ON/OFF
Inch/Metric
Response Speed: Unlimited
Battery:
Silver oxide cell SR-44 (1 pc.)
Part No. 541980
Battery Life:
Approx. 20,000 hrs. (continuous
operation)
Accuracy (20° C)
± .001”
Remarks
.075 Round depth bar
± .001”
± .001”
with OD Carbide Jaw
± .001”
with OD, ID Carbide Jaw
± .001”
± .001”
with OD Carbide Jaw
± .001”
± .0015”
± .0015”
with OD Carbide Jaw
± .0015”
12/8/03
9:52 PM
Page 1
CALIPERS
Digimatic Calipers with Absolute Encoders
Series 500 –
Featuring Position Memory and 3.5 Year Battery Life
500-171
T
EC
Optional Accessories
SPC Connecting Cables
No.959149(1m), No.959150(2m)
Add-on
Hold Switch
OG
Y
AB
LUT
SO E
H N OL
DATA
HOLD
No.959143
Features built-in
Data Switch
MITUTOYO’s new Absolute
Encoder Digimatic Caliper offers
special functions which allow it to
always remember its measuring
position even after the gage has
been switched off.
• Origin: Allows setting of an origin
starting point to be used as reference in subsequent measurements (generally set to closed jaw
IN/MM
ORGIN
HOLD
OFF
position). Once set, the Absolute
Encoder caliper will switch on
showing its true position from the
origin point rather than 0.0000 as
with standard models.
• Zero/ABS: Allows the display to
be Zero-Set at any point along the
slider for incremental comparison
measurements. This switch will
also allow return to the absolute
ON/ZERO
mode and display of the true
position from the origin point.
Also provided is inch/mm conversion and SPC data output. Another
outstanding feature of the Absolute
Encoder Digimatic Caliper is 3.5
years of use under normal working
conditions from just a single SR44
battery cell. (541980)
Specifications
Metric (SPC output models)
Order No.
500-150
500-151
500-152
500-153
500-500-10
Range
0–100mm
0–150mm
0–200mm
0-300mm
0–450mm
LCD
Resolution
0.01mm
0.01mm
0.01mm
0.01mm
0.01mm
Accuracy
±0.02mm
±0.02mm
±0.02mm
±0.03mm
±0.05mm
500-501-10
0–600mm
0.01mm
±0.05mm
Remarks
1.9mm Round Depth Bar.
without Depth Bar, Absolute
Function Type
without Depth Bar, Absolute
Function Type
For SPC output order Connecting Cable 959149 (1m) or 959150 (2m).
Replacement Battery: 541980 (1pc), 541980-10 (10 pcs/SET)
O-3
12/8/03
9:53 PM
Page 1
CALIPERS
L
D
B
C
G
F
ABSOLUTE
E
A
Battery Cover
Dimensions
Order No.
500-170, 500-195
500-171, 500-196,
500-159, 500-160,
500-175, 500-178,
500-174
500-172, 500-197,
500-163, 500-164,
500-176, 500-177
500-173, 500-193,
500-165, 500-166,
500-167, 500-168
500-505-10
500-506-10
500-507-10
500-150
500-151
500-152
500-153
500-500-10
500-501-10
A
1.57"
1.57"
B
.83"
.83"
C
.65"
.65"
D
2.26"
2.26"
E
1.42"
1.42"
F
.63"
.63"
G
.138"
.138"
L
7.09"
9.10"
1.97"
.96"
.79"
2.26"
1.42"
.63"
.138" 11.34"
2.52"
1.08"
.86"
2.80"
1.60"
.79"
.15"
15.87"
3.54"
3.54"
5.11"
1.57"
1.57"
1.97"
2.52"
3.54"
3.54"
1.85"
1.85"
2.36"
.83"
.83"
.96"
1.08"
1.85"
1.85"
1.50"
1.50"
1.65"
.65"
.65"
.79"
.86"
1.50"
1.50"
3.61"
3.61"
4.49"
2.26"
2.26"
2.26"
2.80"
3.61"
3.61"
2.44"
2.44"
2.87"
1.42"
1.42"
1.42"
1.60"
2.44"
2.44"
.98"
.98"
1.26"
.63"
.63"
.63"
.79"
.98"
.98"
.24"
.24"
.31"
.138"
.138"
.138"
.15"
.24"
.24"
24.80"
30.70"
48.82"
7.09"
9.10"
11.34"
15.87"
24.80"
30.70"
Digimatic Caliper with Absolute Encoder
Inch/Metric (SPC output Models)
LCD
Range
Resolution
0-4"
.0005"
0–100mm
0.01mm
500-171
0-6"
.0005"
0–150mm
0.01mm
500-174
0–6"
.0005"
0–150mm
0.01mm
500-175
0–6"
.0005"
0–150mm
0.01mm
500-178
0–6"
.0005"
0–150mm
0.01mm
500-172
0-8"
.0005"
0–200mm
0.01mm
500-176
0–8"
.0005"
0–200mm
0.01mm
500-177
0–8"
.0005"
0–200mm
0.01mm
500-167
0–12"
.0005"
0–300mm
0.01mm
500-168
0–12"
.0005"
0–300mm
0.01mm
500-173
0-12"
.0005"
0–300mm
0.01mm
500-505-10
0–18"
.0005"
0–450mm
0.01mm
500-506-10
0–24"
.0005"
0–600mm
0.01mm
500-507-10
0–40"
.0005"
0–1,000mm
0.01mm
For SPC output order Connecting Cable 959149 (1m) or 959150 (2m).
Order No.
500-170
O-4
Accuracy
Remarks
±.001"
.075" Round Depth Bar.
±.001"
±.001"
with OD Carbide Jaw, Absolute Function Type
±.001"
with OD, ID Carbide Jaw, Absolute Function Type
±.001"
.075 Round Depth Bar, Absolute Function Type
±.001"
±.001"
with OD Carbide Jaw, Absolute Function Type
±.001"
with OD, ID Carbide Jaw, Absolute Function Type
±.0015"
with OD Carbide Jaw
±.0015"
±.0015"
±.002"
without Depth Bar, Absolute Function Type
±.002"
±.003"
12/8/03
9:54 PM
Page 1
CALIPERS
Digimatic Solar Powered Caliper
with Absolute Encoder (Solar CD)
Series 500 – with or without SPC output
500-464
T
EC
OG
Y
AB
LUT
SO E
H N OL
500-474
Optional Accessories:
(For output models only)
SPC Connecting Cables
No.959149(1m), No.959150(2m)
DATA
SOLAR ABSOLUTE MyCAL
DIGIMATIC CALIPER
The Solar Absolute MyCAL is Mitutoyo's latest
advancement in caliper technology.
The Absolute Encoder feature eliminates the need for zero
setting each time the caliper is turned on.
The Solar Absolute MyCAL will always turn on showing its
true position. Memory of the origin point will not be lost
when power is cut off even if the caliper is left in complete
darkness for extended periods. Additionally, the Absolute
scale provides unlimited response speed which means no
more over-speed errors. For comparison measurements an
incremental measurement function is also provided.
Power is supplied by built-in solar cells which operate even
in low light conditions down to 60 Lux.
Features built-in
Data Switch
Add-on
Hold Switch
No.959143
IN/MM
HOLD
ORGIN
HOLD
OFF
ON/ZERO
O-5
12/8/03
9:54 PM
Page 1
CALIPERS
Dimensions
D
B
F
G
C
E
A
Order No. A
B
500-463
7.1"
500-490
3.03"
500-464
9.1"
500-474
500-465
11.34" 3.56"
500-492
❈ t : Jaw Thickness
C
D
.65"
1.57"
.79"
E
F
G
t❈
2.30"
1.50"
.63"
.138"
1.97"
Output Specifications
5
4
3
2
1
DAT
A/H
OLD
Pin No. Signal
I/O
1
2 *1
3 *1
4
—
O
O
O
GND
DATA
CK
RD
Description
Ground
Measurement data
Clock for data transmission
Ready for data transmission
5 *2
REQ
1
Request for data transmission
*1 Open drain: -0.3 ~ +7.0V, 400µA max.
*2C-MOS: Pull-up to VDD(1.55V)
Specifications
Digimatic Solar Powered Calipers with Absolute Encoder
Inch/Metric
LCD
Range
Resolution
Accuracy
Remarks
0–4"
.0005"
±.001"
.075" Round Depth Bar
0–100mm
0.01mm
with SPC output
0–6"
.0005"
±.001"
with SPC output
0–150mm
0.01mm
0–8"
.0005"
±.001"
with SPC output
0–200mm
0.01mm
0–4"
.0005"
±.001"
.075" Round Depth Bar
0–100mm
0.01mm
without SPC output
0–6"
.0005"
±.001"
without SPC output
0–150mm
0.01mm
0–8"
.0005"
±.001"
without SPC output
0–200mm
0.01mm
output order Connecting Cable 959149 (1m) or 959150 (2m). Note: Solar Cells should be maintained over 60 lux.
Order No.
500-463
500-464
500-465
500-473
500-474
500-475
For SPC
O-6
12/10/03
11:10 AM
Page 1
CALIPERS
Coolant Proof Digimatic Caliper
with Absolute Encoder (IP-66 Level Protection)
Series 500
Dimensions
L
C
B
D
The World's First
Coolant Proof Caliper
A
Introducing Mitutoyo's Coolant-Proof caliper,
the world's first digital caliper sealed against
fluids and contaminants!
Mitutoyo introduces the toughest digital caliper in the
world–the first that's IP-66 rated: coolant-proof, dust-proof,
chip-proof. Use it anywhere in the shop. It also includes
Mitutoyo's patented absolute encoder technology, the "Set
'n Forget" origin set-up feature. Now you can take digital
measurements in places you never could before!
Models available with SPC output.
Dimensions
Range
0-6"/0-150mm
0-8"/0-200mm
0-12"/0-300mm
L
9.1"
11.3"
16.1"
A
1.6"
2.0"
2.5"
B
.83"
.96"
1.1"
C
.65"
.79"
.86"
D
.63"
.63"
.79"
Optional Accessories
SPC Cable
1m/40": 05CZA624
2m/80": 05CZA625
Technical Data
Quantizing Error:
Repeatability:
Display:
Functions:
Dust/Water Protection
Level:
Battery:
Battery Life (0-6"):
Battery Life (0-12"):
Measuring System:
± 1 Count.
.0005"/0.01mm
LCD (Character height: .3"/7.5mm)
Origin setting, Automatic power on/off*1
Inch/mm conversion, Data output
IP66 (IEC 60529)
SR44 (1pc.) up to 8" (2pc.) for 12"
Approx. 3-year under normal use
Approx. 1-year under normal use
Electromagnetic induction type absolute
linear encoder*2
Unlimited
Response Speed:
*1 Patent pending (Japan, U.S.A., China, UK, France)
*2 Design pending (Japan, U.S.A., China, UK, France)
IP66 Protection
Type
Operator-safe and
protection against
foreign matter
Protect against
water
Level
6: Protection
against dust
5: Protection
against water
jet
Definition
Protect the equipment
against dust not to
penetrate.
Protect the equipment
against water jet that’s*
from any direction.
* Condition: Using a nozzle with 12.5mm ID and water jet with 30Kpa
water pressure (approx. 100L/min) on the equipment from a distance
of a meter for 3 minutes or over (1 minute per 1m2 superficial area).
Specifications
Order No.
Measuring Range
LCD Resolution
Accuracy
500-672
500-682
500-673
500-683
500-674
500-684
0-6"/0-150mm
0-6"/0-150mm
0-8"/0-200mm
0-8"/0-200mm
0-12"/0-300mm
0-12"/0-300mm
.0005"/0.01mm
.0005"/0.01mm
.0005"/0.01mm
.0005"/0.01mm
.0005"/0.01mm
.0005"/0.01mm
±
±
±
±
±
±
.001"
.001"
.001"
.001"
.0015"
.0015"
Remarks
With SPC Output
With SPC Output
With SPC Output
O-7
12/8/03
9:56 PM
Page 1
CALIPERS
Digimatic Plastic Calipers
Plasti-Cal Series 700
700-126
Plasti-Cal - our first multi-purpose, nonindustrial-use digital caliper! Ideal for
use in the lab...the woodshop...the classroom...the nursery...the doctor's office...any
application involving delicate or unusual
workpieces. Plastic construction makes for
durable and light-weight use, and plastic
jaws won't mar easily-damaged surfaces.
Reads in inch or millimeters.
Alarm: Battery voltage low
Over speed
Response speed: 63"/s (1,600mm/s)
Without SPC output and Depth Bar.
700-103Y
Inch/Metric
Order No.
700-103Y
Range
Resolution
Accuracy
Remarks
0-6"
.001"
±.008"
Yellow
0-150mm
0.1mm
±0.2mm
700-126
0-6"
.001"
±.008"
Black
0-150mm
0.1mm
±0.2mm
Battery life: Approx. two years (under normal use).
Replacement Battery: 541980 (1pc), 541980-10 (10pcs SET)
MyCal Lite
Series 700 – Economy version Digimatic Caliper
with all steel construction
700-113
MyCal Lite is an innovative, new Digimatic®
Caliper which is economically priced to
allow everyone to benefit from the advantages of modern digital gages. Large LCD
digits ensure error free reading in either inch
or mm mode. Additionally, the zero point can
be set anywhere to allow quick comparison
measurements.
Inch/Metric
Order No.
700-113
700-123
O-8
Range
0-6"
0-150mm
0-8"
0-200mm
Specifications
Response Speed
Battery
Battery Life
Display
Alarm
Resolution
.001"
0.1mm
.001"
0.1mm
63"/s (1,600mm/s)
Silver oxide cell SR-44 (1 pc.) #541980
Approx: two years (under normal use)
LCD 4-digit (-) sign. Character height: .295"
Battery voltage low. Over speed.
Accuracy
±.005"
±0.2mm
±.005"
±0.2mm
Remarks
No SPC output
Depth Bar Provided
No SPC output
Depth Bar Provided
12/8/03
9:58 PM
Page 1
CALIPERS
Dial Calipers
Series 505
505-675
505-717
Features
• Improved durability, the sliding surfaces of the main
blade are coated with titanium.
• Slider displacements are amplified by a rack-and-pinion
mechanism indicated on the dial.
• QUADRI (4-Way) measurement, see next page.
• Extra-rigid main beam. Hardened stainless steel.
• Supplied in fitted carrying case.
• Black-Face/Ratchet Type
Model 505-675-66 features an alternative dial face in
black with white markings and a bright orange indicator
needle for easy reading. This model is also equipped
with Mitutoyo's new ratchet thumb roller providing a positive-clicking action just like a micrometer ratchet thimble.
• Other alternate color dial face calipers are also available
which are useful for identifying different users or departments and maintaining calibration schedules.
See listing below.
Specifications
Dial Calipers
Inch
Order No.
Range
0–4"
0–4"
0–6"
0–6"
0–6"
0–6"
0–6"
0–6"
0–6"
0–6"
0–6"
Dial Reading
Resolution
Range/Rev.
.001"
.20"
.001"
.10"
.001"
.20"
.001"
.10"
.001"
.10"
.001"
.10"
.001"
.10"
.001"
.10"
.001"
.10"
.001"
.10"
.001"
.10"
Accuracy
(20•)
±.001"
±.001"
±.001"
±.001"
±.001"
±.001"
±.001"
±.001"
±.001"
±.001"
±.001"
505-716
505-674
505-717
505-675
505-675-51
505-675-52
505-675-53
505-675-54
505-675-55
505-675-56
505-675-66
505-718
505-708
505-712
505-689
505-690
505-719
505-676
505-709
505-713
505-720
505-721
505-677
505-710
505-714
0–6"
0–6"
0–6"
0–6"
0–8"
0–8"
0–8"
0–8"
0–8"
0–12"
0–12"
0–12"
0–12"
0–12"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
±.001"
±.001"
±.001"
±.001"
±.002"
±.002"
±.002"
±.002"
±.002"
±.002"
±.002"
±.002"
±.002"
±.002"
.20"
.10"
.10"
.10"
.10"
.20"
.10"
.10"
.10"
.20"
.20"
.10"
.10"
.10"
Remarks
Dial Face: A
Dial Face: B
Dial Face: A
Dial Face: B
Blue Dial Face, Dial Face: B
Purple Dial Face, Dial Face: B
Green Dial Face, Dial Face: B
Red Dial Face, Dial Face: B
Orange Dial Face, Dial Face: B
Black Dial Face, Dial Face: B
Black Dial Face, Dial Face: B
with Ratchet Stop
Dial Face: A with OD Carbide Jaw
Dial Face: B with OD Carbide Jaw
Dial Face: B with OD, ID Carbide Jaw
Dial Face: B Extra Smooth Movement
Dial Face: B Extra Smooth Movement
Dial Face: A
Dial Face: B
Dial Face: A
Dial Face: A with OD Carbide Jaw
Dial Face: B
O-9
12/17/03
9:20 AM
Page 1
CALIPERS
“Quadri” (4-way) Measurement
1. Outside measurement
2. Inside measurement
3. Step measurement
A
4. Depth measurement
.200" Per One Revolution
B
Dimensions
.100" Per One Revolution
A
D
B
G
F
C
H
E
Dimensions
Order No.
505-674
505-716
505-675
505-675-51
505-675-52
505-675-53
505-675-54
505-675-55
505-675-56
505-675-66
505-689
505-708
505-712
505-717
505-718
505-676
505-690
505-709
505-713
505-719
505-677
505-710
505-714
505-720
505-721
B
C
D
H
E
F
G
t❈
9.1"
3.03"
.65"
1.57"
.83"
2.25"
1.5"
.63"
.35"
11.34"
3.56"
.79"
1.97"
.96"
15.9"
4.4"
.87"
2.52"
1.08"
2.7"
1.7"
.79"
.15"
A
7.1"
O-10
12/8/03
10:02 PM
Page 1
CALIPERS
Dial Calipers
Series 505
505-671
Features
• Imporoved durability, the sliding surfaces of the
main blade are coated with titanium.
• Shock proof construction 1mm revolution models.
• Supplied in fitted carrying case.
505-681
Specifications
1mm / Revolution
Metric
Order No.
505-680
505-681
505-682
Range
0–100mm
0–150mm
0–150mm
Dial Reading
Resolution
Range/Rev.
0.01mm
1.0mm
0.01mm
1.0mm
0.01mm
1.0mm
Accuracy
±0.015mm
±0.02mm
±0.03mm
Remarks
Dial Face: C
Dial Face: C
Dial Face: C
2mm / Revolution
Metric
Order No.
505-671
505-707
505-711
505-683
505-672
505-684
505-673
Range
0–150mm
0–150mm
0–150mm
0–150mm
0–200mm
0–200mm
0–300mm
Dial Reading
Resolution
Range/Rev.
0.02mm
2.0mm
0.02mm
2.0mm
0.02mm
2.0mm
0.02mm
2.0mm
0.02mm
2.0mm
0.02mm
2.0mm
0.02mm
2.0mm
Accuracy
±0.03mm
±0.03mm
±0.03mm
±0.03mm
±0.03mm
±0.03mm
±0.04mm
Remarks
Dial Face: D
Dial Face: D
Dial Face: D
Dial Face: D
Dial Face: D
Dial Face: D
Dial Face: D
with OD carbide jaw
with OD, ID carbide jaw
with extra smooth movement
with extra smooth movement
O-11
12/15/03
10:13 AM
Page 1
CALIPERS
“Quadri” (4-way) Measurement
1. Outside measurement
2. Inside measurement
3. Step measurement
C
4. Depth measurement
1mm Per One Revolution
D
Dimensions
2mm Per One Revolution
A
D
B
G
F
C
H
E
Dimensions
Order No.
505-680
505-671
505-681
505-683
505-707
505-711
505-672
505-682
505-648
505-714
B
C
D
H
E
F
G
t❈
231
77
16.5
40
21
57.2
39.5
16
3.5
288
90.5
20
50
24.5
403
111.5
22
64
27.5
70.2
43.4
20
3.8
O-12
unit:mm
A
180
12/8/03
10:04 PM
Page 1
CALIPERS
Series 550
Y
AB
LUT
SO E
550-225-10
OG
T
EC
H N OL
Features
Technical Data:
• The minimum inside measuring length is .4" on the 12"
and smaller range model and 1.0" on the larger range
models.
• Inside and outside measurements can be directly read
from the upper and lower slider graduations, respectively.
• The Digimatic Caliper provides digital readout to
.0005"/0.01mm for error-free reading.
Repeatability:
Display:
Functions:
.0005"/0.01mm
LCD 5-digit
ON/OFF
ZERO/ABS
ORIGIN
INCH/MM
Heavy Duty Dial Caliper
Series 504
504-106
Features
• Provides highly repeatable inside measurements.
• Direct reading of inside dimensions.
O-13
12/8/03
10:04 PM
Page 1
CALIPERS
Dimensions (Unit: inch)
Order No.
550-221-10
550-241-10
550-223-10
550-225-10
550-227-10
504-106
A
11.34
15.87
24.80
30.71
48.82
15.87
B
1.61
1.97
2.56
2.56
3.74
1.97
C
2.36
2.95
3.94
3.94
5.51
2.95
D
.20
.20
.25
.25
.50
.20
E
.31
.47
.71
.71
.94
.47
F
.63
.79
.98
.98
1.26
.79
A
*t
.118
.150
.236
.236
.315
.150
ON
0
10
20
ABSOLUTE
IN
F
MIN
ON/OFF
ZERO/ABS
*t : Jaw Thickness
C
B
E
R=.20"
D
Specifications
Heavy Duty Digimatic Calipers with Absolute Encoder
Inch/Metric (with SPC output)
Order No.
550-221-10
550-241-10
550-223-10
550-225-10
550-227-10
Range
Outside
0–8"
0–200mm
Inside
.4–8"
10.16–200mm
LCD
Resolution
.0005"
0.01mm
0–12"
0–300mm
0–18"
0–450mm
.4–12"
10.16–300mm
.5–18"
12.7–450mm
.0005"
0.01mm
.0005"
0.01mm
±.0015"
0–24"
0–600mm
.5–24"
12.7–600mm
.0005"
0.01mm
±.002"
0–40"
0–1000mm
1.0–40"
25.4–1000mm
.0005"
0.01mm
±.003"
Accuracy
±.001"
Remarks
without Depth Bar
Absolute Function Type
without Depth Bar
±.002"
without Depth Bar
without Depth Bar
without Depth Bar
Absolute Function Type SPC Connecting Cable: 959149 (1m) or 959150 (2m).
Heavy Duty Dial Caliper
Inch
Order No.
504-106
O-14
Range
Outside
0–12"
Dial Reading
Inside
.4–12"
Resolution
.001"
Range/Rev
.20"
Accuracy
±.002"
12/8/03
10:05 PM
Page 1
CALIPERS
Digimatic Snap Calipers with Absolute Encoder
Series 573
Locking clamp
573-281-10
Spring loaded
thumb lever
1. Push the whole sliding unit
against your masterpiece.
(Gage Block used here)
Lock with clamp.
2. Use zero-set function to zero the
Digimatic display.
EC
OG
This caliper also features the new
Absolute scale which always knows
its true position from the origin
point.
T
This special version of MITUTOYO’s
Digimatic Caliper features a springloaded mechanism to allow quick
and efficient GO/±NG inspection.
Set-up is a simple operation as
shown below.
Y
AB
LUT
SO E
H N OL
3. Open and close jaws with snap
lever to check workpieces
allows .079"(2mm) retraction.
Specifications
Digimatic Snap Calipers with Absolute Encoder
Inch/Metric
LCD
Range
Resolution
Accuracy
0–4"
.0005"
±.001"
0–100mm
0.01mm
573-282-10
0–6"
.0005"
±.001"
0–150mm
0.01mm
For SPC output order Connecting Cable 959149 (1m) or 959150 (2m). Replacement Battery: 541980 (1pc),
Order No.
573-281-10
Remarks
with SPC output
with SPC output
541980-10 (10 pcs/SET)
O-15
12/8/03
10:05 PM
Page 1
CALIPERS
Digimatic Carbon Fiber Calipers
Series 552 – Wide Range Models with a Lightweight Beam
552-313
552-160
These large Digimatic Calipers have a beam constructed
of a strong carbon fiber which makes them both durable
and easy to handle. Standard jaws will take both outside
and inside dimensions. Optional attachments available for
special measurements.
Features
• Lightweight Digimatic caliper that employs CFRP
(Carbon Fiber Reinforced Plastics) in the beam and
jaws.
• The range of applications can be expanded by using
the optional attachments.
• Display: 6-digit LCD with a minus sign (-)
• Functions include:
Preset of desired starting point
Inch/mm conversion
Zero-setting, Data hold, Error alarm, Low battery alarm,
Data output. (Note: Data hold and output functions cannot be used at the same time.)
• Power supply: One SR44 (541980)
• Battery life: Approx. two years under normal use
(Approx. one year in continuous operation)
• Provided with a data output port for connection with the
SPC system.
Specifications
Digimatic Carbon Fiber Calipers
Range
Range
LCD
Outside
Inside
Resolution
Accuracy
Remarks
0–18"
.5–18.5"
.0005"
±.003"
Jaw Depth: 7.9"
0–450mm
12.7–462mm
0.01mm
0–24"
.5–24.5"
.0005"
±.003"
Jaw Depth: 7.9"
0–600mm
12.7–612mm
0.01mm
0–18"
.5–18.5"
.0005"
±.002"
with Ceramic Jaws
0–450mm
12.7–462mm
0.01mm
0–24"
.5–24.5"
.0005"
±.002"
with Ceramic Jaws
0–600mm
12.7–612mm
0.01mm
0–12"
.5–12.5"
.0005"
±.0015"
0–300mm
12.7–312mm
0.01mm
0–18"
.5–18.5"
.0005"
±.002"
0–450mm
12.7–462mm
0.01mm
0–24"
.5–24.5"
.0005"
±.002"
0–600mm
12.7–612mm
0.01mm
0–40"
1.0–41"
.0005"
±.003"
0–1000mm
25.4–1025mm
0.01mm
0–60"
1.0–61"
.0005"
±.0035"
0–1500mm
25.4–1525mm
0.01mm
output order Connecting Cable 905338 (1m) or 905409 (2m). Replacement Battery: 541980 (1 pc.), 541980-10 (10 pcs./SET)
Order No.
552-160
552-161
552-165
552-166
552-311
552-312
552-313
552-314
552-315
For SPC
O-16
12/8/03
10:06 PM
Page 1
CALIPERS
L
Output connector
5
A
B
Beam
INSIDE
DIGIMATIC
C
Main scale
2
OFFSET value label
3
4
Slider stopper
1
6
E
D
Slider
Jaw, Beam
G
F
(Minimum measurable inside dimensions)
J
H
I
Switch function
1 ON/OFF
2 ZERO
3 OFFSET
4 PRESET
5 DATA/HOLD
6 in/mm
Order No.
552-311
552-312
552-165
552-160
552-313
552-166
552-161
552-314
552-315
(Unit: Inch)
L
19.3
A
1.62
B
3.61
C
.98
D
2.56
E
3.94
F
.25
G
.71
H
.50
I
.31
J
.31
25.2
1.62
3.61
.98
2.56
3.94
.25
.71
.50
.31
.31
25.2
1.62
3.61
.98
2.56
7.9
.25
.71
.50
.31
.31
31.1
1.62
3.61
.98
2.56
3.94
.25
.71
.50
.31
.31
31.1
48.8
68.5
1.62
3.61
.98
2.56
7.9
.25
.71
.50
.31
.31
2.47
4.8
1.26
3.94
5.90
0.50
.94
1.00
.47
.31
OPTIONAL JAW ATTACHMENTS
914016 Attachment clamp for 12", 18", 24"
models (1pc.)
914048 Attachment clamp for 40" & 60"
models (1pc.)
880099 Centerline attachment (1pc.)
914018 Inside point attachment (1pc.)
.98"
.39"
3.94"
NOTE: One attachment clamp is required
for each jaw attachment piece ordered.
A
B
3.7"
Dimensions
ø.04"
D
.31"
C
E
(Jaw closed)
DIMENSIONS
914016 —
A 914048 —
B 880099 —
C 880099 —
D 914018 —
E 914018 —
2.05"
2.44"
.40"
.40"
1.0"
2.0"
O-17
12/8/03
10:06 PM
Page 1
CALIPERS
Digimatic Versa Gage
Series 552
552-281
Features
• Lightweight gage employing Carbon Fiber Reinforced Plastics
in the beam.
• 6" and 12" Models are hardened stainless steel.
• An expandable variety of applications.
• Easy to read 6 digit LCD display with resolutions to .0005”
increments.
• Inch/Metric
• SPC output.
• Hold button allowing operator to take accurate measurements
in difficult and awkward positions.
Specifications
Inch/Metric
Order No.
552-281
552-282
552-283
552-284
552-285
552-286*
552-287*
*Optional
O-18
Linear Range
0-18”
0-460mm
0-24”
0-620mm
0-40”
0-1040mm
0-60”
0-1554mm
0-80”
0-2170mm
0-6”
0-152.4mm
0-12”
0-322mm
accessories are not available for
Cone Range
1.125-19.1”
28.5-485mm
1.125-25.5”
28.5-647mm
1.35-42.3”
34-1075mm
1.35-62.6”
34-1590mm
1.35-86.5”
34-2197mm
.75-6.9”
19-175mm
.75-12.75”
19-322mm
6" and 12" models.
Depth Range
14”
355mm
14”
355mm
23”
584mm
23”
584mm
NA
6”
152.4mm
7.5”
190mm
Resolution
.0005”
0.01mm
.0005”
0.01mm
.0005”
0.01mm
.0005”
0.01mm
.0005”
0.01mm
.0005”
0.01mm
.0005”
0.01mm
Accuracy
±.002”
±.002”
±.003”
±.0035”
±.0045”
±.0015”
±.0015”
12/8/03
10:07 PM
Page 1
CALIPERS
Series 552
Optional Accessories*
Order No.
64AAA520
64AAA521
64AAA522
64AAA523
64AAA524
64AAA525
64AAA526
64AAA527
64AAA528
64AAA529
64AAA530
64AAA531
64AAA532
64AAA533
64AAA534
64AAA535
64AAA536
905338
905409
541980
*6" and 12"
Description
ø2.25" Cone Center Extender (Pair)
ø3.62" Cone Center Extender (Pair)
ø5" Cone Center Extender (Pair)
ø.5" Cone Center Reducer (Pair)
ø.75" Cone Center Reducer (Pair)
Flange Pin Reducer Block
#34 Single Cone #4-48 Tapped for 40", 60",
80" Gages
#34 Dual Cone #4-48 Tapped for 40", 60",
80" Gages
#28.5 Dual Cone #4-48 for 18", 24" Gages
#28.5 Single Cone #4-48 for 18", 24" Gages
Edge Guides for 40", 60" 80"
Edge Guides for 18", 24"
Wooden Box for 18"
Wooden Box for 24"
Wooden Box for 40"
Wooden Box for 60"
Wooden Box for 80"
SPC output cable (1m)
SPC output cable (2m)
SR44 Battery
models cannot use optional accessories.
Cone Extenders
Cone Reducers
Length and Width
O-19
12/8/03
10:07 PM
Page 1
CALIPERS
Series 551
551-224-10
L
G
ON
10
20
IN
ABSOLUTE
MIN
F
ZERO/ABS
Order No.
551-221-10
551-241-10
551-224-10
551-226-10
551-227-10
G: Jaw Thickness
L
11.34
15.87
26.77
37.91
48.43
A
1.18
1.57
2.20
2.20
2.20
B
1.69
2.68
4.51
4.51
4.51
C
2.36
3.54
5.90
5.90
5.90
D
.20
.20
.25
.25
.50
E
.31
.39
.59
.59
.79
F
.63
.79
.98
.98
1.26
G
.118
.150
.236
.236
.315
B
C
ON/OFF
H N OL
A
0
T
EC
OG
Y
AB
LUT
SO E
E
D
Features
Technical Data:
• The sharp jaw edges provide easy
access to portions that ordinary calipers
cannot measure.
• The Digimatic Caliper provides digital
readout to .0005"/0.01mm for error-free
reading.
Repeatability:
Display:
Functions:
.0005"/0.01mm
LCD 5-digit
ON/OFF
ZERO/ABS
ORIGIN
INCH/MM
Specifications
Digimatic Caliper with Absolute Encoder
Range
Outside
0–8"
0-200mm
551-241-10
0–12"
0-300mm
551-224-10
0–20"
0-500mm
551-226-10
0–30"
0-750mm
551-227-10
0–40"
0-1000mm
SPC Connecting Cable: 959149 (1m)
Order No.
551-221-10
Range
LCD
Inside
Resolution
Accuracy
Remarks
.4–8"
.0005"
±.001"
10.16-200mm
0.01mm
.4–12.4"
.0005"
±.002"
10.16-310.16mm
0.01mm
without Depth Bar
.5–20"
.0005"
±.0025"
12.7-500mm
0.01mm
.5–30"
.0005"
±.003"
12.7-750mm
0.01mm
1.0–41"
.0005"
±.003"
25.4-1025mm
0.01mm
or 959150 (2m). Replacement Battery: 541980 (1 pc.), 541980-10 (10 pcs./SET)
Metric (with SPC output)
Order No.
551-201-10
Range
Outside
0–200mm
Range
Inside
10–200mm
LCD
Resolution
0.01mm
Remarks
without Depth Bar
SPC output order Connecting Cable 959149 (1m) or 959150 (2m) for replacement battery: 541980 (1 pc.), 541980-10 (10 pcs./SET)
O-20
Accuracy
±0.03mm
12/8/03
10:08 PM
Page 1
CALIPERS
Digimatic Special Face Calipers
with Absolute Encoder
Series 573
573-234-10
Blade Type
Digimatic Caliper
573-251-10
Neck Type
Digimatic Caliper
573-252-10
Outside Point Type
Digimatic Caliper
LUT
SO E
AB
573-261-10
T
EC
OG
Y
Tube Thickness Type
Digimatic Caliper
H N OL
These calipers offer some additional special jaw styles
for difficult to reach dimensions.
Additionally, these models incorporate Mitutoyo's exclusive Absolute reading scale.
The Absolute scale always knows its true position from
the origin point and never needs zero-setting.
Specifications
Digimatic Special Face Calipers with Absolute Encoder
LCD
Range
Resolution
0–6"
.0005"
0–150mm
0.01mm
573-251-10
0–6"
.0005"
0–150mm
0.01mm
573-252-10
0–6"
.0005"
0–150mm
0.01mm
573-261-10
0–6"
.0005"
0–150mm
0.01mm
*For SPC order Connecting Cable 959149 (1m) or 959150 (2m).
All models listed above operate on a single SR-44 battery which lasts
Order No.
573-234-10
Accuracy
±.001"
±.0015"
±.0015"
±.002"
Remarks
Blade type
& OD Carbide Jaw
Neck type,
without Depth Bar
Outside Point Type
without Depth Bar
Tube Thickness type
without Depth Bar
approximately 3.5 years with normal use.
O-21
12/8/03
10:09 PM
Page 1
CALIPERS
Digimatic Special Face Calipers
Series 573
Blade Type
in/mm
Neck Type
DATA/HOLD
in/mm
OFF
ON /ZERO
.39"
1.38"
1.57"
.03"
.79"
Tube Thickness Type
Outside Pointed Type
in/mm
in/mm
DATA/HOLD
OFF
ø.12"
30°
.20"
O-22
1.57"
30°
ø.02"
ON /ZERO
ø.09"
1.50"
1.57"
OFF
ON /ZERO
.20"
1.57"
OFF
.39"
DATA/HOLD
DATA/HOLD
ON /ZERO
12/8/03
10:09 PM
Page 1
CALIPERS
Digimatic Inside Calipers with Absolute Encoder
Series 573
573-246-10
Inside Pointed Jaw
Type Absolute
Encoder Digimatic
Caliper
573-245-10
Inside Groove Type
Absolute Encoder
Digimatic Caliper
573-242-10
Inside Knife-Edge Type
Absolute Encoder
Digimatic Caliper
T
EC
OG
Y
AB
LUT
SO E
H N OL
Features
• Specially designed for inside measurements in hard to
reach places.
• The Digimatic Caliper provides digital readout to
.0005"/0.01mm for error-free reading.
• All Digimatic models provide
SPC output. Additionally, these models incorporate
Mitutoyo's exclusive Absolute reading scale. The
Absolute scale always knows its true position from the
origin point and never needs zero-setting.
• Power Supply: Silver oxide cell (SR-44 1 pc.)
• Battery Life: 3.5 years under normal use.
Specifications
Digimatic Inside Calipers with Absolute Encoder
Order No.
573-242-10
573-245-10
573-246-10
Range
0"– 8"
0-200mm
.4"– 6"
10.16-150mm
.8"– 6"
20.32-150mm
LCD
Resolution
.0005"
0.01mm
.0005"
0.01mm
.0005"
0.01mm
Accuracy
±.002"
±.002"
±.0015"
Remarks
Knife-edge type,
Without Depth Bar
Inside groove type,
Without Depth Bar
Pointed jaw type,
Without Depth Bar
Metric (with SPC output)
Order No.
573-146-10
Range
20 –150mm
LCD
Resolution
0.01mm
Accuracy
±0.03mm
Remarks
Pointed jaw type,
Without Depth Bar
For SPC output order connecting cable 959149 (1m) or 959150 (2m). Replacement Battery: 541980 (1pc), 541980-10 (10 pcs/SET)
O-23
12/8/03
10:10 PM
Page 1
CALIPERS
Digimatic Inside Pointed Jaw
IN/MM
DATA/HOLD
0.0000
30°
.2"
ø.02"
ø.09"
ON/ZERO
1.50"
OFF
1.57"
Inside Point
Additional values for width of jaws imprinted on frame.
+.8 in.
+20.32mm
Inside Groove
Additional values for width of jaws imprinted on frame.
+.4 in.
+10.16mm
.4" .4"
.8"
Digimatic Inside Groove
Digimatic Inside Knife Edge
IN/MM
1.4800
0.0000
.2"
.4"
O-24
.01"
.12"R
2.76"
.14"
.2"
OFF
ON/ZERO
.12"
1.38"
.79"
OFF
DATA/HOLD
DATA/HOLD
ON/ZERO
.31"
.12"
IN/MM
12/8/03
10:10 PM
Page 1
CALIPERS
Offset Calipers
Series 573, 536
573-201-10
Offset Type
Digimatic Caliper
536-401
Offset Vernier
Caliper
AB
LUT
SO E
T
EC
A
OG
Y
536-701
Offset Dial
Caliper
H N OL
B
C
Features
• Main scale jaw can slide up and
down to facilitate measurement of
stepped sections.
• The Digimatic Calipers provide digital readout to .0005"/0.01mm for
error-free reading. These models
also incorporate Mitutoyo's exclusive Absolute reading scale.
• All models feature a depth rod.
Hard-to-get-at dimensions such as
A, B, C, can be accurately measured with an offset vernier caliper.
Specifications
Offset Digimatic Calipers with Absolute Encoder
LCD
Range
Resolution
Accuracy
0–6"
.0005"
±.001"
0–150mm
0.01mm
573-202-10
0–8"
.0005"
±.001"
0–200mm
0.01mm
573-203-10
0–12"
.0005"
±.0015"
0–300mm
0.01mm
*For SPC output order Connecting Cable 959149 (1m) or 959150 (2m).
All models listed above operate on a single SR-44 battery which lasts approximately 3.5 years with normal use.
Order No.
573-201-10
O-25
12/8/03
10:11 PM
Page 1
CALIPERS
A
B
C
Order No.
573-201-10
573-202-10
573-203-10
H
20
0
70
ABSOLUTE
DIGIMATIC
2n
G
A
9.21
11.53
15.87
B
.295
.335
.472
C
.65
.79
.86
D
3.74
3.74
5.31
E
.394
.394
.60
F
1.57
1.97
2.52
G
.63
.63
.79
H
.138
.138
.15
D
F
E
A
C
B
Dimensions (Offset Dial & Vernier Calipers)
Order No.
536-101
536-401
536-701
A
B
C
9.02"
.63"
3.74"
D
.394"
.4"
E
F
.98"
1.58"
S
.0197" .138"
JAW
S
t
E
F
T: Jaw Thickness
D
Offset Vernier Calipers
Inch
Order No.
536-401
Range
Lower scale
Upper scale
0–6"
—
Vernier Resolution
Lower scale
Upper scale
.001"
—
Accuracy
±.001"
Range
Lower scale
Upper scale
0-150mm
—
Vernier Resolution
Lower scale
Upper scale
0.05mm
—
Accuracy
±0.05mm
Metric
Order No.
536-101
Offset Dial Calipers
Inch
Order No.
536-701
O-26
Range
0–6"
Dial Reading
Resolution
Range/Rev.
.001"
.20"
Accuracy
±.0015"
t
12/8/03
10:11 PM
Page 1
CALIPERS
Offset Centerline Calipers
Series 573, 536
A
573-206-10
Offset Centerline
Digimatic Type
in/mm
ORGIN
ABSOLUTE
in
DIGIMATIC
B
ZERO/ABS
ON/OFF
E
C
AB
LUT
SO E
Specially designed offset vernier and Digimatic calipers
are used for center to center distance measurements on
the same and offset planes.
These calipers also measure from edge to center. A sum
H N OL
Order No.
A
536-105
536-405
8.86
573-205-10
573-206-10 11.10
* t: Jaw Thickness
Measures center to center on the even and offset planes. Also measures from edge to center. Direct reading (center distances).
EC
D
OG
ØF
T
Offset Centerline
Vernier Type
Y
536-405
B
C
.63
2.95
D
.394
.40
E
øF
1.06
*t
.118
.0394
1.18
Hole Diameter
.06–.394
.138
of .2" (5mm in metric) should be subtracted from the
measured dimensions in this case.
The movable jaw is approximately 3" long and adjustable
by means of the clamp provided.
Features
• Direct reading center distance measurements in Inch or
Metric.
• Hole diameter should be larger than .06" (1.5mm) but
smaller than .4" (10mm).
• Supplied with fitted carrying case.
• The Digimatic Calipers provide digital readout to
.0005"/0.01mm for error-free reading. These Models
also incorporate Mitutoyo‘s exclusive Absolute Encoder.
Specifications
Digimatic Offset Centerline Calipers with Absolute Encoder
LCD
Range
Resolution
Accuracy
Remarks
.4"–6"
.0005"
±.0015"
10.16-150mm
0.01mm
without Depth Bar
573-206-10
.4"–8"
.0005"
±.0015"
10.16-200mm
0.01mm
without Depth Bar
For SPC output order connecting cable 959149 (1m) or 959150 (2m). Replacement Battery: 541980 (1pc), 541980-10 (10pcs/SET).
Order No.
573-205-10
Vernier Offset Centerline Calipers
Inch
Order No.
536-405
Range
.4"–6"
Vernier Resolution
Lower scale
Upper scale
.001"
1/128"
Accuracy
±.0015"
Remarks
without Depth Bar
Range
10–150mm
Vernier Resolution
Lower scale
Upper scale
0.05mm
-—
Accuracy
±0.05mm
Remarks
without Depth Bar
Metric
Order No.
536-105
O-27
12/8/03
10:12 PM
Page 1
CALIPERS
Digimatic Point Calipers with Absolute Encoder
Series 573
9.09"
.138"
in/mm
ON
0
IN
573-221-10
ON/OFF
80
90
ABSOLUTE
100 4 110
DIGIMATIC
.39"
1.57"
Point Type
Absolute Encoder
Digimatic Caliper
70 3
ZERO/ABS
.012"
.012"
Point Type
573-221-10
20°
9.09"
30°
.138"
573-225-10
in/mm
ON
IN
Extended Point Type
Absolute Encoder
Digimatic Caliper
0 70 3 80
90
100 4 110
ABSOLUTE
DIGIMATIC
ZERO/ABS
.39"
1.57"
ON/OFF
.08"
LUT
SO E
T
EC
OG
Y
AB
.08"
Extended Point Type
573-225-10
H N OL
Shallow planes and similar dimensions can be accurately
measured with MITUTOYO Point and Extended Point
Calipers.
The narrow tip jaws fit into very small grooves and tracks,
making many previously difficult outside measurements
far easier to obtain.
Digimatic models now feature Mitutoyo‘s exclusive
Absolute encoder.
Features
• Comes with inside jaws.
• Measures depth and step dimensions.
• Includes carrying case.
Specifications
Digimatic Point Calipers with Absolute Encoder
LCD
Range
Resolution
0–6"
.0005"
0–150mm
0.01mm
573-225-10
0–6"
.0005"
0–150mm
0.01mm
*For SPC output order Connecting Cable 959149 (1m) or 959150 (2m). All models
battery which lasts approximately 3.5 years with normal use.
Order No.
573-221-10
O-28
Accuracy
±.001"
±.001"
listed above operate on a single SR-44 (541980)
12/8/03
10:12 PM
Page 1
CALIPERS
Low Pressure Calipers
Series 573, 536
573-291-10
Low Pressure
Digimatic Caliper
536-252
Low Pressure
Dial Caliper
IN/MM
To measure resilient workpieces
take the measurement when the
pointer is between the two index
lines.
DATA/HOLD
AB
LUT
SO E
ON/ZERO
T
1.57"
EC
OG
Y
OFF
H N OL
Features
• Designed specifically to measure resilient workpieces.
Contact pressure: .49N to .98N (50 to 100gf)
• Due to the low measuring force these calipers are ideal
for elastic workpieces such as plastic parts that standard calipers cannot measure.
• Easy fine feeding with the thumb roller.
• The jaw on the blade travels .012"/0.3mm.
• Digimatic caliper provides direct digital reading to
.0005"/0.01mm on an LCD screen. This model also
features an Absolute Encoder.
• Digimatic caliper can be linked to the SPC System.
Specifications
Digimatic Low Pressure Caliper with Absolute Encoder
Order No.
573-291-10
Range
0–7"
0–180mm
LCD
Resolution
.0005"
0.01mm
Accuracy
±.002"
Remarks
without Depth Bar
Measuring Force: .49N to .98N
For SPC output order connecting cable 959149 (1m) or 959150 (2m). Replacement Battery: 541980 (1pc), 541980-10 (10 pcs/SET)
Low Pressure Dial Calipers
Inch
Order No.
536-252
Range
0–7"
Dial Reading
Resolution
Range/Rev.
.001"
.20"
Accuracy
±.002"
Remarks
Range
0 – 180mm
Dial Reading
Resolution
Range/Rev.
0.05mm
5.0mm
Accuracy
±0.05mm
Remarks
Metric
Order No.
536-251
O-29
12/8/03
10:13 PM
Page 1
CALIPERS
How to Read Vernier Calipers
Fractional Reading Vernier Scale.
1/16" on the main beam is subdivided
into eight or to 1/128".
Because of .300" inside jaw thickness,
the vernier is placed .300" off from
zero point.
Position of the
vernier plate can
be readjusted.
1/16"
Graduations
on the main beam.
Decimal Reading Vernier
Scale. 1/40th of an inch is
subdivided into 25 by the
vernier to read to onethousandth. One inch is
first divided into ten, and
then 40 graduations.
Each smallest graduation
on the main beam represents .025".
Inch Fractional and Decimal Readings
This vernier caliper has two scales which enable readings to a fraction of an inch as in the case of 1/128"
graduated vernier (upper scale), or in decimals as in the
case of 1/1000" graduated vernier (lower scale).
Each division on the fractional main scale represents
1/16th of an inch. The vernier further subdivides each
division on the main scale to read 1/128 of an inch.
Each division of the decimal main scale represents one
fortieth of an inch or .025". Each fourth line marked by 1
represents .100", the line marked 2 represents .200",
and so forth. The vernier consists of 25 equal divisions
which further subdivides each division on the main
scale to .001".
1. 1/128" graduated vernier (upper scale)
Readings on the main scale................................16/16"
Vernier scale reading ...........................................3/128"
Final reading...........................16/16 + 3/128 = 151/128"
2. 1/1000" graduated vernier (lower scale)
Main scale reading ............................................1.375"
Vernier scale reading......................................... .023"
Final reading ....................................................1.398"
O-30
.300"
Rounded inside
jaws. Thickness
.300" when closed.
Inch Decimal Reading Only (for Inside and
Outside Jaws)
The vernier reads inside and outside dimensions with
the same jaws. Inside measurements are taken by the
specially designed jaw construction. Because of the
.300" inside jaw thickness, the vernier is placed .300" off
from zero point. Taking this difference into account, the
final inside reading is .300" greater than the outside
reading.
Like the Vernier Caliper in the preceding column, the
vernier above also reads to 1/1000 of an inch. In this
case, however, each division on the main scale represents one-twentieth of an inch or .050". This means each
division on the main scale is twice as wide as the previous example, and therefore, the vernier must span twice
the length to read to 1/1000 of an inch.
1. Inside vernier reading (upper scale)
Reading on the main scale.................................1.200"
Vernier line coinciding with main scale line........ .018"
Final reading ....................................................1.218"
2. Outside vernier reading (lower scale)
Reading on the main scale................................. .900"
Vernier line coinciding with main scale line........ .018"
Final reading..................................................... .918"
12/8/03
10:14 PM
Page 1
CALIPERS
Series 530
Plain and Basic vernier caliper with locking screw atop
the moving slider.
Series 531
The jaws move only when spring loaded thumb clamp
is depressed.
Series 532
With fine-adjustment for precise measurement.
530-314
Outside jaws are carbide faced for measurements of
abrasive products.
O-31
12/8/03
10:15 PM
Page 1
CALIPERS
Precision Vernier Calipers
Series 530, 531, 532
531-129
532-106
530-312
Features
• The finest of vernier calipers for accurate work, with
Mitutoyo’s exclusive “Quardi” 4-way measuring feature.
• Can measure OD, ID, depth and steps.
• Models available with a fine-adjustment carriage to
fine-feed the slider.
Specifications
Vernier Caliper (with Fine Adjustment)
Inch
Range
Order No.
532-104
532-105
532-106
Lower scale
0–5"
0–7"
0–11"
Upper scale
0–5"
0–7"
0–11"
Vernier Resolution
Lower scale
Upper scale
.001"
1/128"
.001"
1/128"
.001"
1/128"
Accuracy
±.0015"
±.0015
±.0015"
Upper scale
0–5"
0–7"
0–11"
Vernier Resolution
Lower scale
Upper scale
0.02mm
.001"
0.02mm
.001"
0.02mm
.001"
Accuracy
±0.03mm
±0.03mm
±0.04mm
Inch/Metric
Range
Order No.
532-119
532-120
532-121
O-32
Lower scale
0–130mm
0–180mm
0–280mm
12/8/03
10:16 PM
Page 1
CALIPERS
A
Dimensions (Fine Adjustment Type)
C
D
.65"
1.58"
.81"
1.97"
.87"
2.52"
E
F
G
t❈
3.0"
1.23"
.63"
.118"
3.66"
1.5"
.79"
.150"
D
B
F
G
C
Order No.
A
B
532-104
9.02" 3.05"
532-119
532-105
11.34" 3.58"
532-120
532-106
15.87" 4.39"
532-121
E
Vernier Calipers
Inch
Order No.
530-105
530-314
Range
Lower scale
Upper scale
0–6"
0–6"
0–6"
0–6"
Vernier Resolution
Lower scale
Upper scale
.001"
1/128"
.001"
1/128"
Accuracy
±.0015"
±.0015"
530-116
0–8"
.001"
±.0015"
0–8"
1/128"
Remarks
with OD
Carbide Jaw
Inch/Metric
Order No.
530-104
530-312
530-118
530-115
530-119
530-101
530-108
530-321
Range
Lower scale
Upper scale
0–150mm
0–6"
0–150mm
0–6"
0–200mm
0–8"
0–300mm
0–12"
0–300mm
0–12"
0–150mm
—
0–200mm
—
0–200mm
—
Vernier Resolution
Lower scale
Upper scale
0.05mm
1/128"
0.02mm
.001"
0.02mm
.001"
0.05mm
1/128"
0.02mm
.001"
0.05mm
—
0.05mm
—
0.05mm
—
Accuracy
±0.05mm
±0.03mm
±0.03mm
±0.08mm
±0.04mm
±0.05mm
±0.05mm
±0.05mm
530-109
530-322
0–300mm
0–300mm
—
—
0.05mm
0.05mm
—
—
±0.08mm
±0.08mm
530-501
0–600mm
—
0.05mm
—
±0.10mm
Remarks
with OD
Carbide Jaw
with OD
Carbide Jaw
Vernier Caliper (with Thumb Clamp)
Inch
Range
Order No.
531-113
531-114
Lower scale
0–6"
0–8"
Upper scale
0–6"
0–8"
Vernier Resolution
Lower scale
Upper scale
.001"
1/128"
.001"
1/128"
Accuracy
±.0015"
±.0015"
Upper scale
0–6"
0–6"
0–8"
0–8"
Vernier Resolution
Lower scale
Upper scale
0.05mm
1/128"
0.02mm
.001"
0.05mm
1/128"
0.02mm
.001"
Accuracy
±0.05mm
±0.03mm
±0.05mm
±0.03mm
Inch/Metric
Range
Order No.
531-107
531-128
531-108
531-129
Lower scale
0–150mm
0–150mm
0–200mm
0–200mm
O-33
12/8/03
10:17 PM
Page 1
CALIPERS
Dimensions (Thumb Clamp Type)
C
D
A
E
F
G
1.22"
.63"
E
F
G
G
2.11"
G
1.97"
F
.81"
F
1.58"
D
.65"
C
E
B
Order No.
A
B
531-113
9.02" 3.05"
531-107
531-128
531-114
11.34" 3.58"
531-108
531-129
Dimensions (Vernier Calipers)
O-34
D
.65"
1.58"
A
2.13"
1.18"
.63"
E
C
C
.81"
1.97"
.87"
2.52"
2.64"
1.42"
.79"
1.5"
3.54"
3.54"
1.97"
.98"
D
B
Order No.
A
B
530-105
530-314
9.02" 3.05"
530-104
530-312
530-101
530-116
530-118
11.34" 3.58"
530-108
530-321
530-115
530-119
15.87" 4.39"
530-109
530-322
530-501
30.71" 6.38"
12/15/03
10:16 AM
Page 1
CALIPERS
Diamond Master Vernier Calipers
Series 522
DIAMOND MASTER
522-600
VERNIER CALIPER
A
Features
E
F
G
C
D
B
Vernier
graduation
Dimensions
Order No.
A
522-601
9.02"
522-602
522-600
2
30
3
4
• The main and vernier scales are flush-fitted
to eliminate parallax errors because of the
diamond-shaped (octagonal) cross section
of the main scale.
• Can Measure steps.
Mainscale
scale
Main
graduation
graduation
B
C
D
E
F
G
t❈
3.05"
.67"
1.60"
2.11"
1.18"
.59"
.138"
Diamond master(Parallel Scale Faces)
Diamond-shaped
cross section of
main scale
Specifications
Inch/Metric
Order No.
522-601
522-602
Range
Lower scale
Upper scale
0–150mm
0–6"
0–150mm
0–6"
Vernier Resolution
Lower scale
Upper scale
0.05mm
1/128"
0.02mm
.001"
Accuracy
±0.05mm
±0.03mm
Remarks
Diamond Master Vernier Caliper
Metric
Order No.
522-600
Range
Lower scale
Upper scale
0–150mm
—
Vernier Resolution
Lower scale
Upper scale
0.05mm
—
Accuracy
±0.05mm
O-35
12/8/03
10:19 PM
Page 1
CALIPERS
Vernier Calipers
Series 160, 534
160-124
534-107
534-117
Features
• With a fine-adjustment carriage to fine-feed the slider.
• Long jaws for measuring hard-to-reach portions.
• The jaws have round measuring faces for accurate ID
measurement.
• No depth measuring bar.
Specifications
Long Jaw Vernier Calipers with Fine Adjustment.
Inch
Order No.
534-117
534-118
534-119
534-120
Range
Outside
0–12"
0–20"
0–30"
0–40"
Range
Inside
.3–12"
.8–20"
.8–30"
.8–40"
Vernier Resolution
Outside
Inside
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
Accuracy
±.002"
±.003"
±.004"
±.004"
Inch/Metric
Order No.
Lower scale
Range
Upper scale
Vernier Resolution
Lower scale
Upper scale
Accuracy
534-105
534-106
534-107
534-108
0–300mm
0–500mm
0–750mm
0–1000mm
0–12"
0–20"
0–30"
0–40"
0.02mm
0.02mm
0.02mm
0.02mm
±0.04mm
±0.06mm
±0.08mm
±0.10mm
O-36
.001"
.001"
.001"
.001"
12/8/03
10:19 PM
Page 1
CALIPERS
Dimensions
F
G
H
3.55"
4.06"
1.5"
.79"
.47"
4.41"
2.01"
.98"
5.91"
2.46"
1.26"
2.95"
4.06"
1.5"
.79"
.47"
4.92"
3.94"
4.41"
2.01"
.98"
.71"
48.82" 6.77"
5.51"
5.91"
2.46"
1.26"
17.52" 4.33"
26.85" 8.86"
39.17"
7.87"
9.14"
.73"
48.43"
17.52" 3.74"
24.88"
30.71"
70.87" 8.35"
7.09"
6.7"
.95"
1.18"
I
.394"
.3"
.787"
.8"
.787"
.8"
.787"
.8"
.3"
.5"
.394"
.5"
.5"
.787"
.5"
.5"
.787"
1.0"
1.0"
.787"
1.0"
1.0"
.787"
t❈
A
E
.150"
.236"
G
E
F
D
.315"
D
B
.150"
H
A
B
Order No.
534-105
534-117
534-106
534-118
534-107
534-119
534-108
534-120
160-124
160-125
160-127
160-116
160-119
160-128
160-102
160-103
160-101
160-105
160-106
160-104
160-111
160-112
160-110
I
.236"
.315"
❈ t ; Jaw Thickness
Vernier Calipers with Nib Style Jaws and Fine Adjustment
Inch
Range
Lower scale
0–12"
0–18"
0–24"
0–40"
0–60"
0–80"
Range
Upper scale
.3–12"
.5–18"
.5–24"
1.0–40"
1.0–60"
1.0–80"
Vernier Resolution
Lower scale
Upper scale
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
.001"
Order No.
Range
Lower scale
Range
Upper scale
Vernier Resolution
Lower scale
Upper scale
Accuracy
160-125
160-119
160-103
160-106
160-112
0–12"
0–18"
0–24"
0–40"
0–60"
0–300mm
0–450mm
0–600mm
0–1000mm
0–1500mm
.001"
.001"
.001"
.001"
.001"
±.0015"
±.002"
±.002"
±.003"
±.004"
Range
Outside
0–300mm
0–450mm
0–600mm
0–1000mm
0–1500mm
Range
Inside
10–300mm
20–450mm
20–600mm
20–1000mm
20–1500mm
Vernier Resolution
Outside
Inside
0.02mm
0.02mm
0.02mm
0.02mm
0.02mm
0.02mm
0.02mm
0.02mm
0.02mm
0.02mm
Order No.
160-124
160-116
160-102
160-105
160-111
160-114
Accuracy
±.0015"
±.002"
±.002"
±.003"
±.004"
±.005"
Inch/Metric
0.02mm
0.02mm
0.02mm
0.02mm
0.02mm
Metric
Order No.
160-127
160-128
160-101
160-104
160-110
Accuracy
±0.04mm
±0.05mm
±0.05mm
±0.07mm
±0.09mm
O-37
12/8/03
10:20 PM
Page 1
CALIPERS
Center Line Gage
050001
Application for 4", 6" and 8" Vernier,
Dial and Digimatic Calipers,
requiring dimensions
over .375".
050018
Application for 12"
Vernier, Dial and
Digimatic Calipers
requiring dimensions
over .5".
Pairs of conical probes are specially
designed for Digimatic, Dial and
Vernier calipers to quickly measure
centerline distances.
Due to the fact that the smaller
attachment is .375" in diameter, and
that the conical points are .375"
apart when closed, the centerline
gages do not measure distances
less than .375" when the caliper is
closed with the attachment installed.
The centerline distance is read
directly off the caliper without a conversion factor.
Each probe has two small holding
bolts and the attachment is supplied
with an Allen wrench. The probes
are black oxide finished, and are
quite durable for the required measurements.
The 60° conical probe snugly fits into
the holes, and takes guesswork away
from center distance measurements.
C
A
B
Dimensions
L
050001
050018
Specifications
Center Line Gage
Order No.
050001
050018
O-38
Description
For 4, 6 and 8" Calipers
For 12" Calipers
A
.375"
.500"
B
2.187"
2.75"
C
.141"
.154"
12/8/03
10:20 PM
Page 1
CALIPERS
Calipers Depth Base Attachment
050083
Features
• For 4", 6", 8" and 12" MITUTOYO Vernier, Dial and
Digimatic Calipers.
• Choice of 3" or 4" base length for 6" and 8" models.
• Finely ground base surface and secure locking clamp.
Length
050083
3"
050084
4"
050085
5"
Description
For 4", 6" &
8" models
For 4", 6" &
8" models
For 12"
models only
A
B
C
D
.98"
3"
.96"
.35" .63"
.98"
4"
.96"
.35" .63"
1.18" 5"
E
1.12" .45" .79"
D
E
C
Order No.
A
B
Application
Example
All measurements in inches.
O-39

MITUTOYO - Micro Precision Calibration

Transcription

Similar documents

positioners