Potdevin Machine Company - Pro Pack Solutions Inc.

Potdevin Machine Company - Pro Pack Solutions Inc.

Potdevin Machine Company
26 Fairf ield Place
> NJ °7006
Website: www.potdevin.com
Phone: (201) 288-1941
Fax: (201) 288-3770
West Caldwell
OPERATING INSTRUCTIONS FOR POTDEVIN LABEL PASTERS
6"-8 1/2"-12"
Wipe the rollers and machine clean of dust with a rag. OIL MACHINE DAILY pour
in paste until it is W below the scraper bar.
PASTE AND GLUE: Ask your local supplier to suggest the best machine paste or glue
for your needs. Do not use thick brush paste thinned with water as it usually looses its
thickness. Obtain a sample of prepared machine paste from your supplier.
PASTE COATING ADJUSTMENT: A numbered dial regulator is provided on the 6,
8 l/2, and 12" pasters to permit accurate regulation of the paste coating. As the distance
between the scraper and the pasting roller increases, the paste coating becomes thicker.
The quantity of paste on the label is very important as too much will cause wrinkles, curl
and ooze at the label edges. Try different adjustments and also different amounts of
water dilution in the paste until a good result is obtained. Usually the least dilution and
the thinnest coating offer the best-finished job.
SHIPPING AND PARCEL POST LABELING:
immediately to the package.
Use a thin coating and attach labd
APPLICATION OF PASTED LABELS: For labeiing bottles, jars, packages, other
containers and paper sheets, use a fluid, sticky paste. Adjust the machine to apply a thin
coating so none will spread at the edges of the label. Adjust the machine to apply enough
paste so that the paste will not dry out if the label lays for a couple of minutes.
METHOD #1: Machine-paste about 20 labels and lay them on a damp cloth* PASTE
SIDE UP Then place the labels on the containers, using the labels in the order pasted.
When the labels are applied, they will not curl at the edges, wrinkle, or blister. This
method is desirable when varnished labels or heavy paper labels are used.
METHOD #2: Lay JQ or 20 packages on the table so the surface to be labeled is up.
Lay each pasted label on a package immediately after removal from the machine. Then
space the labels properly and press them flat. This method reduces hand operations and
saves time. The label should lay flat and tight with very little rubbing.
The best method will depend on the thickness of the paper and the type of glue.
Pro Pack Solutions, Inc.
(404) 292-7080 or
(800)274-0123
OPERATING INSTRUCTIONS FOR POTDEVIN LABEL PASTERS
6"-8 1/2"-12"
CLEAN THE MACHINE WHEN FINISHED EACH DAY: clean all paste from
rollers and strippers. Empty paste tank and rinse thoroughly with water.
TROUBLE: jf ^g iabei js caught by the strippers, try the following:
1. Clean the strippers.
2. Feed the label corner first.
3. See that the paste is not too thick or sticky.
4. Sharpen the strippers with a fine file if they are dull. We can supply new
strippers when yours are too worn.
6 - 8 1/2 - 12 PASTERS: ^he strippers should be placed on the gauge mounted at the
rear of the machine. The point should lie tightly in the angle of the gauge. A set screw
on each stripper permits the stripper point to be adjusted correctly. If the point protrudes
too far from the stripper holder, the labels will pass underneath the strippers and fall in
the paste tank.
When the machine is not in use during the day, cover it with a damp cloth so that the
paste will not dry out. In case your results are unsatisfactory, contact us immediately.
NEW PARTS: Strippers, gears, and rollers can be sent to you at any time the machine
becomes worn. All parts are interchangeable. Always mention the number, type, and
size of the machine when ordering parts.
Pro Pack Solutions, Inc.
(404) 292-7080 or
(800)274-0123
GENERAL INSTRUCTIONS
INSTRUCTIONS FOR SHARPENING & ADJUSTING TYPE LM STRIPPER FINGER
#1. This device is a gauge for setting & adjusting pick-off fingers. It is mounted on the machine.
Fingers shown are used on the following types: LM6", LM8", 2R, LA, LH8, & LH12
Stttiag Oangt
LM-547A FINGER SETTING GAUGE
LM-523A BRASS FINGER ASSEMBLY, CONSISTING OF: LM-524A brass finger blade and
LM-525 finger holder.
Shown in set position: LM-523A or LM-306B Finger Assembly
«• A»»esblx
LM-306B ZINC PLATED FINGER ASSEMBLY, CONSISTING OF: LM-296B zinc plated finger
blade and LM-525 finger holder.
INSTRUCTIONS FOR SHARPENING: These are pick-off fingers. Several are provided with each
machine, the number depending on the width of the machine. Replacement blades are available from
stock. These fingers will not work properly if they are blunt, bent or burred in any way. They should
be kept free from such defects and when worn should be dressed by filing edge "A".. A
V
LM-524A brass finger blade only
LM-296B zinc plated finger blade only
Aftanblj-
FINGER ASSEMBLY
LM-524A OR LM-296B
FINGER BLADE
LM-525 FINGER HOLDER ONLY: INSTRUCTIONS FOR ADJUSTING:
When pick-off fingers have been repaired or dressed as noted above, they should be adjusted to
proper length by means of gauge note under #1.
To do this, loosen screw "B" and place finger assembly in gauge as shown, slide finger into notch
and retighten screw "B", holding parts in position. Fingers so adjusted are ready for re-use.
LM-525 finger holder
Pro Pack Solutions, Inc.
(404) 292-7080 or
(800)274-0123
GENERAL INSTRUCTIONS
LUBRICATION:
OIL PULLEY STUD AND BEARING DAILY
(3) DROPS EVERY DAY - USE SAE - 40 OIL.
GREASE GEARS AS REQUIRED (USUALLY ONCE A WEEK).
iGLOE
PUSH
GLDE MACHINE
L
M
FINGER GAUGE
ADJUSTABLE
BEARING
FILL MACHINE W BELOW EDGE. OCCASIONALLY THIN
GLUE WITH WATER. TURN DIAL "A" CLOCKWISE TO
INCREASE THE THICKNESS OF THE GLUE COATING. EACH
NUMBER INCREASES THE COATING THICKNESS BY .0005
OF AN INCH. TO RESET SCRAPER "B", TURN DIAL "A" TO
ZERO, LOOSEN SCREWS "C" UNTIL SCRAPER "B" TOUCHES
THE ROLLER "E", TIGHTEN SCREWS "C".
PROPER POSITION OF FINGER "F" IS APPROXIMATELY 1/8"
FROM CENTER OF GLUE ROLLER TO THE POINT OF THE
FINGER. TAPERED EDGE OF FINGER MUST BE UP.
TO REMOVE FINGER ROD "G", PUSH SPRING "H" AS
SHOWN. SLIDE FINGER ROD FIRST TOWARDS THE RIGHTHAND BEARING; THEN TOWARDSTHE LEFT-HANDBEARING AND OUT.
HOT FLEXIBLE ANIMAL GLUES ARE KEPT AT THE PROPER
WORKING TEMPERATURE BY AN ELECTRIC HEATER
ENCASED UNDERNEATH THE GLUE TANK. THE HEATER IS
COMPLETELY WIRED, INCLUDING HEAT SWITCH, 15 FT.
CORD, AND SPARABLE PLUG FOR 110 VOLT OR 220 VOLT
SOCKET.
WORN OFF FINGER BLADES "M" SHOULD BE FILED AS
INDICATED WITH LINE (—) AT FINGER POINT. LOOSEN
FINGER POINT SCREW "L". USE GAUGE MOUNTED ON
BACK OF THE MACHINE. MOVE FINGER POINT OUT TO
THE PROPER POSITION IN THE DIE CAST HOLDER "N"
TIGHTEN SCREW "L" AND THE STRIPPER FINGER IS READY
FOR FURTHER USE.
ADJUSTABLE BEARING SHOWN IS RECOMMENDED FOR
HEAVY PAPER, LIGHT CARDBOARD, LEATHERETTE, ETC.
TO CLEAN MACHINE, REMOVE FEED TABLE "I", LIFT
SPRING "J" UNDER THE BELT GUARD AND SWING OPEN
BELT GUARD "K". SLIDE OFF V BELT "V"; REMOVE PASTE
UNIT, AND PLACE UNDER A RUNNING WARM WATER
FAUCET. CLEAN AND RINSE THOROUGHLY.
BELT GUARD
Pro Pack Solutions, Inc.
(404) 292-7080 or
(800)274-0123
PARTS LIST FOR STANDARD TYPE 6LM - LABEL PASTER
PART NO.
DESCRIPTION
LM 501-2B
LM502
LM 503-1
LM504-B
LM506
LM507
LM 508B
LM 508B-1
LM 508B-2
LM 508B-3
LM 508B-4
LM 508B-5
LM 512B
LM 514A
LM 519A
LM 520A
LM521
LM522
LM 306B
LM 296B
LM525
LM526
LM527
LM528
LM529
LM530
LM531
LM532
LM 533A
LM534
LM 535A
LM 536A
LM539
LM540
LM541
LM542
LM 543D
LM 544B
LM 545A
LM546
LM 547A
LM548
LM549
LM 861A
LM864
LM865
LM 550-1
LM551
LM552
SUB ASS'Y MACHINE BASE (W/O MOTOR)
GEAR GUARD
MACHINE BASE
RUBBER FOOT
GEAR GUARD HINGE PIN
GEAR GUARD SPRING
END BEARING ASSEMBLY
BEARING BODY
GLUE ROLLER BEARING INSERT
FEED ROLLER BEARING INSERT
GLUE RETAINER (RUBBER) FOR: LM 508B & 512B
OIL CUP FOR: LM 508B & 512B
END BEARING ASS'Y, LEFT HAND
GLUE ROLLER ASS'Y
FEED ROLLER ASS'Y
FEED ROLLER (ONLY)
FEED ROLLER GEAR
FEED ROLLER WASHER, BRASS
FINGER ASS'Y
FINGER BLADE
STRIPPER FINGER HOLDER
COATING REGULATOR ASS'Y
SCRAPER LEVER
COATING REGULATOR SHAFT
COATING REGULATOR DIAL
GLUE REGULATOR SPRING, 5/8" LONG
GLUE REGULATOR SPRING, 1 7/8" LONG
WASHER
DRIVE PULLEY ASS'Y
DRIVE PULLEY
REDUCTION GEAR
GUM POT ASS'Y (CAST IRON) 2 PINS: LM 544B & LM-548
SCRAPER BRACKET
SCRAPER BLADE
SCRAPER BRACKET PIN, RIGHT HAND
SCRAPER BRACKET PIN, LEFT HAND
FEED TABLE, STAINLESS STEEL
FEED TABLE PIN
FINGER ROD, STAINLESS STEEL
FINGER ROD SPRING
FINGER BLADE SETTING GAUGE
REDUCTION GEAR STUD
PULLEY STUD COLLAR
FEED TABLE SUPPORT
FEED TABLE SUPPORT BUMPER
MOTOR-1/15 HP, 115V
MOTOR PULLEY
DRIVE BELT
GLUE ROLLER GEAR
NOTE: WHEN ORDERERING PARTS, PLEASE SPECIFY PART #, MODEL AND SERIAL # OF
MACHINE.
DIAL SIDE
RIGHT SIDE OF MACHINE
BELT SIDE
LEFY SIDE OF MACHINE
Pro Pack Solutions, Inc.
(404) 292-7080 or
(800)274-0123
cA
^
292-7080 or
PARTS LIST FOR STANDARD TYPE 8LM - LABEL PASTER
ITEM
1
2
PART NO.
LM-522
LM8-20B
3
4
5
6
LM-521
LM-522
LM8-18B
LM-512B
7
8
9
10
11
12
LM-508B-1
LM-508B-2
LM-508B-3
LM-508B-4
LM-508B-5
LM-306B
13
14
15
16
LM-296B
LM-525
LM8-119A
LM-508B
17
18
19
20
21
22
23
LM-508B-1
LM-508B-2
LM-508B-3
LM-508B-4
LM-508B-5
LM-546
24
25
26
27
28
29
30
31
32
33
34
35
LM8-4A
36
37
38
LM-534
LM-535A
LM-549
39
40
LM8-52F
10A-36A
LM-547A
LM8-45
LM8-44
LM-533A
DESCRIPTION
QUANTITY
GLUE ROLLER GEAR
1
FEED ROLLER ASS' Y
2
(CONSIST OF ITEMS 3-5)
1
GEAR, FEED ROLLER
WASHER, FEED ROLLER
1
FEED ROLLER
1
1
LEFT HAND BEARING
SUBASSEMBLY (CONSISTS OF ITEMS 7-11)
1
BODY, LM BEARING
1
BUSHING, GLUE ROLLER BEARING
2
BUSHING, FEED ROLLER BEARING
OIL SEAL
1
1
OIL SEAL
FINGER ASSEMBLY
8
(CONSISTS OF ITEMS 13-14)
FINGER BLADE
1
FINGER HOLDER
1
FINGER ROD
1
1
RIGHT AND BEARING
SUBASSEMBLY (CONSISTS OF ITEMS 17-21)
BODY, LM BEARING
1
1
BUSHING, GLUE ROLLER BEARING
BUSHING, FEED ROLLER BEARING
2
OIL SEAL
1
1
OIL CUP
SPRING FEEDER ROD
1
4
ROUND HEAD BRASS SCREW NO. 10-32 X 1/2 INCH
GLUE ROLLER ASSEMBLY
1
TAPER PIN, NO. 1 X 1/2 INCH LONG
1
2
COTTER PIN, 1/16 X 1/2 INCH LONG
FEED TABLE
NAMEPLATE
GAUGE, FINGER
FLAT HEAD SCREW, NO. 10-32
SCRAPER BLADE
FLAT HEAD SCREW, NO. 10-32
SCRAPER BRIDGE
DRIVE PULLEY SUBASSEMBLY
(CONSISTS OF ITEMS 36-37)
DRIVE PULLEY
GEAR, REDUCTION
COLLAR, REDUCTION GEAR STUD
(CONSISTS OF ITEMS 39-41)
ALLEN HEAD SETSCREW
NO. 10-32 X 3/16 IN. FLAT POINT
COLLAR
1
1
1
1
1
4
1
1
1
1
1
A"
1
1
^
PARTS LIST FOR STANDARD TYPE 8LM - LABEL PASTER
ITEM
42
43
44
45
46
47
48
49
PART NO.
LM-542
LM8-76
LM8-62
LM8-93
LM-544B
LM8-2
LM-541
LM8-80
50
51
52
53
54
55
56
57
58
59
60
61
LM8-49
LM-527
LM-529
62
63
64
LM8-79
LM-507
65
66
67
68
69
LM-130D
LM8-60D
LM-861
LM-530
LM-531
LM-532
LM-865
LM-550-1
LM8-105-1A
LM-864
DESCRIPTION
QUANTITY
1
PI, LEFT HAND SCRAPER
1
DRIVE BELT
1
REDUCTION GEAR STUD
1
COLLAR
2
PIN, FEED TABLE
1
GLUE POT
1
PIN, RIGHT HAND SCRAPER
1
SCRAPER LEVER ASSEMBLY
(CONSISTS OF ITEMS 50-59)
1
REGULATOR SHAFT
1
SCRAPER LEVER
1
REGULATOR DIAL
1
HEX HEAD SETSCREW, NO. 10-32
1
REGULATOR SPRING, 5/8" LONG
1
REGULATOR SPRING, 1-7/8" LONG
4
REGULATOR WASHER
1
DRIVE MOTOR - 1/15 HP, 115 V
4
STEEL WASHER, VA
1
MOTOR PULLEY
1
SETSCREW, NO. 10-32
1
MACHINE BASE SUBASSEMBLY
(CONSISTS OF ITEMS 62-66)
1
GEAR GUARD
1
CLAMP, GEAR GUARD
1
ROUND HEAD BRASS SCREW
NO. 8-32
GEAR GUARD PIN
2
1
MACHINE BASE
LM TABLE SUPPORT
1
HEX HEAD SCREW, 14-20 X 5/8
5
FEED TABLE NOISE DAMPER
1
Pro Pack Solutions, Inc.
(404) 292-7080 or
(800)274-0123
LM-8 MACH.
56
51
56
SEE SHEET Z FOR ITEMS 57 THRU 69.
TO SHEET Z
LM-8 MACHINE
SHEET I OF 2
.
Note:
When Ordering Parts, Please Specify Part Number, Model
and Serial Number of Machine.
in Machine Company
Pro Pack Solutions, Inc.
'<
(404) 292-7080 or
(800)274-0123
LM~8 MACH-
—
SEE SHEET I FOR ITEMS I THRU 56.
LM-8 MACHINE
SHEET Z OF 2
Note:
When Ordering Parts, Please Specify Part Number,
Serial and. Model Number of Machine,
Potdevin Machine Company
26 FAIRFIELD PLACE
WEST CALDWELL, NJ 07006
Website: www.potdevin.com
Pro Pack Solutions, Inc.
(404) 292-7080 or
(800)274-0123
zee 3
PARTS LIST FOR STANDARD TYPE 12LM - LABEL PASTER
^
.
ITEM
PART NO.
DESCRIPTION
1
2
LM-552
LM12-20C
3
4
5
6
LM-521
LM-522
LM12-20A
LM-512B
7
8
9
10
11
12
LM-508B-1
LM-508B-2
LM-508B-3
LM-508B-4
LM-508B-5
LM-306B
13
14
15
16
LM-296B
LM-525
LM12-119A
LM-508B
17
18
19
20
21
22
23
LM-508B-1
LM-508B-2
LM-508B-3
LM-508B-4
LM-508B-5
LM-546
24
25
26
27
28
29
30
31
32
LM12-4A
10A-36A
LM-547
33
34
35
36
LM-534
LM-535A
LM-549
GLUE ROLLER GEAR
FEED ROLLER ASSEMBLY
(CONSISTS OF ITEMS 3-5)
GEAR, FEED ROLLER
WASHER, FEED ROLLER
FEED ROLLER
LEFT HAND BEARING SUBASSEMBLY
(CONSISTING OF ITEMS 7-11)
BODY, LM BEARING
BUSHING, GLUE ROLLER
BUSHING, FEED ROLLER
OIL SEAL
OIL CUP
FINGER ASSEMBLY
(CONSISTS OF ITEMS 13-14)
FINGER BLADE
FINGER HOLDER
FINGER ROD
RIGHT HAND BEARING ASSEMBLY
(CONSISTS OF ITEMS 17-21)
BODY, LM BEARING
BUSHING, GLUE ROLLER
BUSHING, FEED ROLLER
OIL SEAL
OIL CUP
SPRING, FEED ROD
ROUND HEAD BRASS SCREW
NO. 10-32 X 1/2 INCH
GLUE ROLLER ASSEMBLY
NAME PLATE
GAUGE
FLAT HEAD SCREW, NO. 10-32
FEED TABLE
SCRAPER BLADE
FLAT HEAD SCREW, NO. 10-32
SCRAPER BRIDGE
DRIVE PULLEY SUBASSEMBLY
(CONSISTS OF ITEMS 33-34)
DRIVE PULLEY
GEAR, REDUCTION
COLLAR, REUCTION GEAR STUD
ALLEN HEAD SETSCREW
NO. 10-32 X 3/16", FLAT POINT
COLLAR
PIN, LEFT HAND SCRAPER
DRIVE BELT
REDUCTION GEAR STUD
COLLAR
37
39
40
41
42
LM12-52
LM12-45
LM12-44
LM-533A
LM-542
10A-25D
LM8-62
LM8-93
5
QUANTITY
1
2
1
1
1
1
1
1
2
1
1
12
1
1
1
1
1
1
2
1
1
1
4
1
1
1
1
1
1
5
1
1
1
1
1
1
1
1
1
1
1
J2 ^
PARTS LIST FOR STANDARD TYPE 12LM - LABEL PASTER
ITEM
PART NO.
DESCRIPTION
43
44
45
46
LM-544B
LM12-2A
LM-541
LM8-80
2
1
1
1
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
LM8-49
LM-527
LM-529
PIN, FEED TABLE
GLUE POT
PIN RIGHT HAND SCRAPER
SCRAPER LEVER SUBASSEMBLY
(CONSISTS IF ITEMS 47-56)
REGULATOR SHAFT
SCRAPER LEVER
REGULATOR DIAL
» 0 -3 a* Vi SETSCREW.
REGULATOR SPRING, 5/8" LONG
REGULATOR SPRING, 1-7/8" LONG
REGULATOR WASHER
TAPER PIN, NO. 1 X W LONG
COTTER PIN, NO. 1/16 X W LONG
FEED TABLE ARM
SCREW, TABLE ADJUSTMENT
NUT, TABLE LOCK
SETSCREW, NO. 10-32
MOTOR PULLEY
DRIVE MOTOR - 1/15 HP, 1 15V
HEX HEAD SCREW, V4-20 X 5/8
STEEL WASHER, V4
MOTOR BASE
GEAR GUARD
CLAMP, GEAR GUARD
ROUND HEAD BRASS SCREW
\0~3Z* V4
GEAR GUARD PIN
MACHINE BASE
2
2 .
2 .
1
1
1
4
4
1
1
1
1
69
70
LM-530
LM-531
LM-532
LM-802A
Z-1653
Z-1264
LM-550-1
LM-865
LM12-900B
LM12-79
LM-507
LM-130D
LM12-60
QUANTITY
1
1
1
1
1
1
4
1
2
2
1
o
0T
o
O CM
00 3-
S~
s
<fr
LM-IZ MACH
12
^
T Y P E LMI2
STANDARD LABEL PASTER
SHEET I OF 2
See sheet 2 for items 60 thru 70
Pbtdevin Machine Company
26 FAIRFIELD PLACE
WEST CALDWELL, NJ 07006 pro Pack Solutions,
Website: www.potdevin.com
292-7080 Of
201-288-1941
201-Z68-3770- /
(8°°V?
-—
LM-12 MACH.
68-3 67
69
65
T Y P E LMI2
STANDARD LABEL PASTER
J
SHEET 2 OFZ
See sheet 1 for items 1 thru 59
Rev.
fbtdevin Machine Company
POTDEVIN^
V
^
26 FAIRPIELD PLACE
WEST CALDWELL, NJ 07006
Website: www.potdevin.com
201-288-1941
Prop
ackso;ut,-on » Inc.