Rumble Wall Fire Place Installation Procedures

Rumble Wall Fire Place
Installation Procedures
1
Capabilities: Wood, Propane, or Natural Gas. If you choose to
configure for propane or natural gas, please seek a licensed
professional to install piping.
Pavestone’s Rumble Wall Fireplace includes:
(1) 36” Stainless Steel Fireplace Insert
(1) 48” Stainless Steel Fireplace Stack
(1) Black Chimney Cap
(2) 56” Galvanized steel (2”x2” 1/8”) Angle Iron
(231) Rumbled Wall Rectangles
(56) Rumbled Wall Squares
(23) Pavestone 18” Cap
(24) Tubes 10.15 oz. of concrete adhesive
Tools Required:
Personal Protective Equipment (PPE): Safety Goggles, hearing protection, dust mask
Rubber Mallet
Level (6” preferred)
6-8 foot ladder
Tape measure
10 oz. Calk Gun
12” Saw with Diamond Blade (Cap cuts required)
Speed Square
2
**Contact your local utility company prior to concrete pad Installation**
Concrete Pad Installation:
Pavestone’s Rumble Wall Fireplace is designed for installation on a concrete pad. Use map
below to determine the zone of your project & construct the appropriate foundation.
3
4
5
6
Step 1: 22 Rectangles/1 Square
Step 2: 22 Rectangles/1 Square
7
Step 3: 21 Rectangles/3 Squares
Note: Center the fire insert 8” inches from the face. Insert has been removed to provide the details of
block locations in until Step 7. Keep insert in place.
Step 4: 10 Rectangles/5 Squares/3 Cap
Not: Cut 3 Cap 13” long x 10” wide
8
Step 5: 7 Rectangles/5 Squares
Step 6: 10 Rectangles/3 Squares
9
Step 7: 9 Rectangles/5 Square
Step 8: 18 Rectangles/10 Squares
Note- In this step all blocks are laid on edge
10
Step 9: 9 Rectangles/5 Squares
Step 10: 12 Rectangles/3 Squares
Note- 2 Rectangles on each side are positioned “on end”
11
Step 11: 7 Rectangles/5 Squares
Note- Place Angle Iron pieces evenly across the front two “on end” rectangle pieces as
shown
Step 12: 13 Rectangles/2
Squares
12
Step 13: 12-18” Cap
Use a chisel or guillotine to split 4 cap 16” long and place them at the corners cap B
Use a diamond blade saw to cut 4 cap at 14 ¼” long cap C
Fill in other spaces with standard caps cap A
B
A
C
A
C
B
C
Layer 13BCap Cutting Details:
A
C
A
B
Is a standard 18” Cap
A
Split 2” from the end of the cap to make them 16” long. Repeat this for 4 caps.
16”
B
Cut the cap to 12” long with a diamond blade saw.
C
12”
13
Step 14: 8 Rectangles/2 Square
14
Step 15: 8 Rectangles/2 Squares
Step 16: 8 Rectangles/2 Squares
Note-Install 48” Stack on top of Fire Place Insert
15
Step 17: 8 Rectangles/2 Squares
Step 18: 8 -18” Cap
cut caps
Spilt caps on outside
B
C
A
B
B
B
A
C
16
Cutting Details for Layer 18 Caps:
A
Standard 18” Cap
Snap at 16” Long to create two snapped faces
B
Cut 4 caps to this dimension
Exposed faces are split sides
First: Cut the back of cap so you have a rough face and a saw cut
back 10” deep
Second Cut: Cut the block to be 11” long
C
Finished dimension is 10”x11” with one rock face along the 11” side
Rough Face
17
Step 19: 7 Rectangles
Step 20: 7 Rectangles
18
Step 21: 7 Rectangles
Steps 22-24: 6 Rectangles each
19
Step 25: Install Chimney Cap. Congratulations your Pavestone Rumble Wall Fireplace installation is
complete.
20