Mosin nagant scope Mount with bolt handle

Mosin Nagant Scope Mount
with bolt handle
Fits:7.62x54R Mosin Nagant Rifles, both round and octagonal receivers
INSTALLATION INSTRUCTIONS
PART# MOI0600
Thank you for purchasing one of Advanced Technology Inc.'s Scope Mounts!
Please fill out the enclosed Unconditional Lifetime Warranty card and mail it within 30 days of purchase.
STEP #4
Clamp bolt in padded vise with
bolt handle upward. Mark bolt
handle base shank (marker or
paint). Measure upward 3/16" on
knob shank from base of bolt and
scribe line on shank. See Sketch
A and B.
Fits all 7.62x54R Mosin Nagant Rifles, both
round and octagonal receivers.
Package contains:
(1) Machined Stainless Bolt Handle
(1) Adapter Bushing (Black Oxide Finish)
(1) 82 Degree Counter Sunk Socket Head 10/32" x 1/2"
(1) #11 (.191/larger) Drill Bit (High Speed Steel)
(1) #21 (.159/smaller) Drill Bit (High Speed Steel)
STEP #5
(1) Hardened Aluminum Black
Anodized Scope Mount
(1) 10-32 Tap
(2) Machine Screws
(1) Instruction Sheet
Note: Satisfactory results can be
achieved by careful installation
or by a qualified gunsmith.
BOLT HANDLE
Bolt Fully
Assembled
For Reference.
STEP #1
Open bolt to be sure weapon is unloaded.
Re-check 3/16" measurement,
leaving room for finish filing (if
necessary) later. Cut off bolt handle.
STEP #6
For "non-stepped" (Sketch A) press the 1/2" spacer inside the new Advanced
Technology, Inc. bolt handle (supplied). "Stepped" (Sketch B) bolt handles DO
NOT require spacer. Place the Advanced Technology, Inc. bolt handle over the cut
off "nub" on the original bolt. Clamp in padded vise with the back face of the
Advanced Technology, Inc. bolt handle FLUSH against front face of original bolt.
(Normal bolt position.)
Remove bolt by lifting bolt, squeezing trigger and pulling bolt out to rear. STEP #7
Using larger #11 drill, carefully "spot drill" area for mount screw - just deep
STEP #3
enough to create a centered starting point for the tap drill - Step #8. Cutting oil
Disassemble bolt. Grasp bolt handle, pull rearward and turn cocking piece 1/4 turn is recommended.
to left, making sure bolt guide bar remains intact. This removes spring tension on
STEP #8
bolt. Bolt head and guide bar slide forward as an assembly, exposing firing pin.
Using the supplied #21 (smaller) drill bit, drill through the center of the bolt
Note position marks at forging. NOTE: BE SURE THE Advanced Technology, Inc. BOLT HANDLE
rear of cocking piece, this IS STILL IN THE ORIGINAL POSITION.
aligns firing pin depth
STEP #9
correctly and must be
returned to exact position Still clamped, use 10-32 tap, and tap hole through bolt. Deburr and thoroughly
for safe operation. Firing clean bolt and handle.
pin (under spring tension)
may now be unscrewed using
STEP #10
fork-shaped end of guide bar Place Advanced Technology, Inc. bolt handle in place on the forging. Install
slide.
and tighten supplied 10/32 countersunk machine screw. Use of thread lock
is recommended. Finished bolt handle should fit flush with forging when
completed.
STEP #2
STEP #11
Reassemble and reinstall bolt in action.
Advanced Technology, Inc. • Made in USA • Lifetime Warranty • No Gunsmithing
www.ATIgunstocks.com • 102 Fieldview Dr. • Versailles, KY 40383 • PH: 859-873-9877 • FAX: 859-873-6229
Page 1 of 2
IS-MOI0600-032408
Mosin Nagant Scope Mount
with bolt handle
Fits:7.62x54R Mosin Nagant Rifles, both round and octagonal receivers
INSTALLATION INSTRUCTIONS
PART# MOI0600
MOUNT
STEP #4
STEP #1
Open bolt to be sure weapon is unloaded.
STEP #2
Remove barreled action from stock. Remove bolt assembly from action by
lifting bolt, squeezing trigger and pulling bolt out to rear.
CAUTION: BEFORE PROCEEDING WITH STEP #3, CHAMBER CLEARANCE MUST
BE CHECKED! DRILLING INTO CHAMBER AREA (INCORRECT MOUNT POSITIONING) MAY RESULT IN INJURY OR DEATH!
STEP #3
Drill press is recommended
for this step.
Place the scope mount
(holes forward) on receiver
flush with receiver ring
front face. Square mount
on receiver using the flat
on the bottom of the
receiver-magazine well area.
Clamp securely in position.
Double check positioning
for squareness.
Use supplied larger #11 drill
and spot drill rear screw
hole. (Spot drill will "mark"
center of hole for next step.)
With mount still clamped,
use supplied smaller #21
drill bit (and cutting oil) to
drill through. (Drill slowly
so as not to burr inside of
receiver below hole.)
With mount still clamped, use supplied 10-32 tap (and oil), to tap through receiver.
Without unclamping, clean
area and securely screw in
the supplied 10-32 x 1/2"
screw. Repeat this process
for the forward hole.
Remove scope mount and clean mount and action. Remove burrs from tapped
holes.
STEP #5
Set scope mount in place, install and tighten screws. (Thread lock is
recommended.) Check screws to be sure they do not protrude below the inner
surface of receiver. NOTE: MOUNT MUST BE USED WITH SUPPLIED REPLACEMENT BOLT HANDLE OR BOLT WILL NOT OPERATE.
Other Advanced Technology, Inc. Products:
Enfield Monte Carlo Stock
#ENF0013(.303 & .308 No 1, Mk3)
#ENF0041 (.303 No 4, Mk1)
.303 Enfield Scope Mount
#ENF0141 or #ENF0113
No Gunsmithing. Stable mount made of
T-6 aluminum with weaver-type base.
(Mount cannot be modified to fit .308)
ENF0113 Shown
Mosin Nagant Monte Carlo Stock
#MOI0300
Also available in Mossy Oak® New Break-Up Camouflage
Mosin Nagant
Scope Mount & Bolt Handle
#MOI0600
Mauser 98 Stock with Built-In Weaver Scope Rail
#MSS1500
Mauser Bolt Handle
#MBH1800
**NOTE: Straight-bolt or wide-arc bolt
Mausers MUST use our Conversion Bolt
Handle to convert to bent-bolt!
Advanced Technology, Inc. • Made in USA • Lifetime Warranty • No Gunsmithing
www.ATIgunstocks.com • 102 Fieldview Dr. • Versailles, KY 40383 • PH: 859-873-9877 • FAX: 859-873-6229
Page 2 of 2
IS-MOI0600-032408