ICD-SX46/SX56/SX66

Transcription

ICD-SX46/SX56/SX66

ICD-SX46/SX56/SX66
SERVICE MANUAL
US Model
Canadian Model
Ver. 1.3 2006.06
ICD-SX46
AEP Model
UK Model
E Model
ICD-SX46/SX56
Chinese Model
Korean Model
ICD-SX46/SX56/SX66
Tourist Model
ICD-SX56
Photo: ICD-SX56
SPECIFICATIONS
Recording media
Built-in flash memory 128 MB (ICD-SX46) /
256 MB (ICD-SX56) / 512 MB (ICD-SX66),
Stereo/Monaural recording
Recording time
Maximum recording time
The maximum recording time of all
the folders is as follows. You can
record messages for the maximum
recording time in a single folder.
Recording modes
ICD-SX46
ST
5 hr.
STLP
11 hr.
SP
17 hr.
LP
47 hr.
50 min.
15 min.
50 min.
35 min.
ICD-SX56
ST
STLP
SP
LP
11 hr.
22 hr.
35 hr.
95 hr.
45 min.
40 min.
55 min.
50 min.
23 hr.
45 hr.
72 hr.
192 hr.
40 min.
30 min.
5 min.
20 min.
ICD-SX66
ST
STLP
SP
LP
(hr.: hours/min.: minutes)
ST: Standard play stereo recording
mode
STLP: Long play stereo recording
mode
SP: Standard play monaural
recording mode
LP: Long play monaural recording
mode
Frequency range
• ST: 60 Hz - 13,500 Hz
• STLP: 60 Hz - 6,900 Hz
• SP: 60 Hz - 7,000 Hz
• LP: 80 Hz - 3,500 Hz
Speaker Approx. 16 mm (21/32 in.) dia.
Power output
150 mW
Input/Output
• Microphone jack (minijack, stereo)
– input for plug in power, minimum input
level: 0.6 mV, 3 kilohms or lower
impedance microphone
• Headphones jack (minijack, stereo)
– output for 8 - 300 ohms headphones
• USB connector
• DC IN 3V jack (For Korean and the People’s
Republic of China models, this jack does not
exist.)
Playback speed control
+100% to –50% (DPC)
Power requirements
Two LR03 (size AAA) alkaline batteries: 3 V DC
Dimensions (w/h/d) (not incl. projecting parts and
controls)
28.0 × 120.0 × 13.8 mm (1 1/8 × 4 3/4 × 9/16 in.)
Mass (incl. batteries)
64 g (2.26 oz)
Supplied accessories
Stereo headphones × 1
USB connecting cable × 1
Application Software (CD-ROM) × 1
LR03 (size AAA) alkaline batteries x 2
Carrying pouch x 1
Your dealer may not handle some of the above listed
optional accessories. Please ask the dealer for detailed
information.
Design and specifications are subject to change without
notice.
IC RECORDER
9-879-953-04
2006F16-1
© 2006.06
Sony Corporation
Connect Business Division
Published by Sony Techno Create Corporation
ICD-SX46/SX56/SX66
TABLE OF CONTENTS
1.
GENERAL ................................................................... 3
2.
DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
Disassembly Flow ...........................................................
Cover (Jack) .....................................................................
Case Block Assy ..............................................................
AUDIO Board, Microphone Unit (Mic2/3) .....................
Ornament Belt Assy, SW Board ......................................
Cover (Chassis) Block Assy ............................................
MAIN Board, Liquid Crystal Display Panel ...................
3.
TEST MODE ............................................................... 9
4.
DIAGRAMS
4-1.
4-2.
4-3.
4-4.
4-5.
4-6.
4-7.
4-8.
4-9.
4-10.
4-11.
4-12.
4-13.
Block Diagram – MAIN Section-1 – .............................
Block Diagram – MAIN Section-2 – .............................
Block Diagram – PANEL Section – ...............................
Printed Wiring Board – AUDIO Board (Side A) – .........
Schematic Diagram – AUDIO Board (Side B) – ............
Schematic Diagram – AUDIO Board (1/2) – .................
Schematic Diagram – AUDIO Board (2/2) – .................
Printed Wiring Board – MAIN Board (Side A) – ...........
Printed Wiring Board – MAIN Board (Side B) – ...........
Schematic Diagram – MAIN Board (1/2) – ...................
Schematic Diagram – MAIN Board (2/2) – ...................
Printed Wiring Board – SW Board – ..............................
Schematic Diagram – SW Board – .................................
5.
EXPLODED VIEWS
5
5
6
6
7
7
8
13
14
15
16
17
18
19
20
21
22
23
24
25
5-1. Case Block Assy .............................................................. 33
5-2. Chassis Block Assy ......................................................... 34
6.
ELECTRICAL PARTS LIST .................................. 35
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 °C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Replacement of IC6001 and IC7003 used in this set requires
a special tool.
• The voltage and waveform of CSP (chip size package) cannot
be measured, because its lead layout is different from that of
conventional IC.
*
• Lead layouts
surface
Lead layout of
conventional IC
CSP (chip size package)
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
Using on house current (excluding the Korean and the
People’s Republic of China models)
Connect the AC power adaptor AC-E30HG (not
supplied) to the DC IN 3V jack of the unit and to the
wall outlet. Do not use any other AC power
adaptor.
Polarity of the plug
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder. Operating instructiondd
2
ICD-SX46/SX56/SX66
SECTION 1
GENERAL
This section is extracted
from instruction manual.
Identifying the front and rear panels of the unit
i (headphones) jack
Built-in microphone
DIRECTNL (directional) switch
VOICE UP (Digital Voice Up) switch
DPC ON/OFF switch
Display window
ERASE button
(bookmark) button
DIVIDE/
A-B
(repeat)/PRIORITY button
OPR (operation) indicator
zREC (record) /REC PAUSE button
xSTOP button
Jog lever
FOLDER/MENU/.(review/fast backward)/
> (cue/fast forward)/x• B (play/stop•enter)
qf VOL (volume) +/– buttons
1
2
3
4
5
6
7
8
9
0
qa
qs
qd
qg
qh
qj
qk
ql
w;
wa
ws
Base
HOLD switch
Speaker
Battery compartment
Clip*
m (microphone) jack
USB connector
DC IN 3V jack
(For Korean and the People’s Republic of China
models, this jack does not exist.)
wd Slit for a handstrap
*Notes
• To prevent the clip from breaking, avoid hooking it on thick
fabric, such as a pocket of a heavy coat.
• When bending down or running with the unit clipped on
your pocket, be careful not to drop the unit.
Using the display window
1 Folder indication
Displays the current folder (A, B, C, D or E).
2 Recording mode indication
Displays the current recording mode:
• ST: Standard play stereo recording mode
• STLP: Long play stereo recording mode
• SP: Standard play monaural recording mode
• LP: Long play monaural recording mode
3 REC (Recording) indicator
4 Remaining battery indicator
When the AC power adaptor (not supplied) is
connected, the indicator does not appear (excluding
the Korean and the People’s Republic of China
models).
5 Remaining memory indicator
6 Priority marks
7 Selected message number /Total message
number in the folder
8 Alarm indicator
Appears when the alarm is set for a message.
9 Repeat play indicator
Appears while a message or a specific portion (A-B)
of the message is played back repeatedly.
0 Bookmark indicator
Appears when the bookmark is set for a message.
qa Counter /Remaining time indication /
Recording date and time indication /Current
time indication
The display selected with the DISP in the menu
appears.
qs SENS (microphone sensitivity) indication
Displays the current microphone sensitivity:
• H (high): To record at a meeting or in a quiet/
spacious place.
• L (low): To record for dictation or in a noisy place.
3
ICD-SX46/SX56/SX66
Step 2: Setting the Clock
You need to set the clock to use the alarm function or record the date and time.
Clock setting display appears when you insert batteries for the first time, or
when you insert batteries after the unit has been without batteries for a certain
period of time. In this case, proceed from step 4.
Jog lever
Press up (>).
Turn toward MENU.
Press the center
(x•B).
Press down (.).
1
Turn the jog lever toward MENU.
The menu mode will be displayed in
the display window
2
Press the jog lever up or down
(>/.) to select “SET DATE”.
3
Press the jog lever (x•B).
The date and time setting window is
displayed. The year digits will flash.
4
Set the date.
1 Press the jog lever up or down
(>/.) to select the digits of
the year.
2 Press the jog lever (x•B).
The month digits will flash.
3 Set the month and day in sequence,
then press the jog lever (x•B).
The hour digits will flash.
v
5
Set the time.
1 Press the jog lever up or down
(>/.) to select the digits of
the hour.
The minute digits will flash.
3 Set the minute.
The menu mode will be displayed
again.
Note
If you do not press the jog lever (x•B) for more than one minute, the clock
setting mode is cancelled and the window will return to normal display.
6
Turn the jog lever toward MENU.
The window will return to normal
display.
1 If the unit is left unused for more than 3
seconds in the stop mode after the clock
is set, the display will show the current
time.
4
Note on setting the clock
Set the clock while the unit is in the
stop mode.
ICD-SX46/SX56/SX66
SECTION 2
DISASSEMBLY
Note: Disassemble the unit in the order as shown below.
2-1. DISASSEMBLY FLOW
SET
2-2.COVER (JACK)
(Page 5)
2-3.CASE BLOCK ASSY
(Page 6)
2-4.AUDIO BOARD,
MICROPHONE UNIT(MIC2/3)
(Page 6)
2-5.ORNAMENT BELT ASSY,
SW BOARD
(Page 7)
2-6.COVER (CHASSIS)
BLOCK ASSY
(Page 7)
2-7.MAIN BOARD,
LIQUID CRYSTAL DISPLAY
PANEL (Page 8)
Note: Follow the disassembly procedure in the numerical order given.
2-2. COVER (JACK)
5 cover (jack)
3 lid (connecter)
4 screw
6 screw
1 battery lid
2 screw (M1.4)
5
ICD-SX46/SX56/SX66
2-3. CASE BLOCK ASSY
3 Slide the chassis from the case completely and remove it.
Pass the flexible board through
the hole during assembling.
2 connector
11pin (CN7005)
1 Slide the chassis from the case until the connector becomes visible.
2-4. AUDIO BOARD, MICROPHONE UNIT (MIC2/3)
3 three claws
4 LCD holder
6 Remove soldering at two positions of the speaker cable.
5 liquid crystal
display panel
8 cushion
9 Remove the microphone unit (MIC2/3)
from the groove.
q; AUDIO board
2
7 connector
4pin (CN3001)
1 connector
40pin (CN7003)
6
ICD-SX46/SX56/SX66
2-5. ORNAMENT BELT ASSY, SW BOARD
2 knob (HOLD)
3 ornamental belt assy
4 six claws
6 ornamental
belt
1 peel off the three
adherent areas
5 three sheets
(ornamental belt)
6 SW board
2-6. COVER (CHASSIS) BLOCK ASSY
chassis block assy
3 speaker (1.6cm)
SP3001
1 claw
1 claw
1 claw
1 claw
2 cover (CHASSIS)
7
ICD-SX46/SX56/SX66
2-7. MAIN BOARD, LIQUID CRYSTAL DISPLAY PANEL
6 sheet, insulating
3 Remove soldering from the two points.
8 MAIN board
4 battery (+) terminal
5 battery (–) terminal
7 liquid crystal
display panel
1 Remove the two battery terminals
from the groove of the chassis.
2
chassis block assy
8
ICD-SX46/SX56/SX66
SECTION 3
TEST MODE
[Setting Method of the Test Mode]
To enter the test mode, turn on the HOLD . switch while pressing the x key and VOL+ key at the same time with the power on.
[Operation in the Test Mode]
After entering the test mode, you can move within the test menu by
pressing the . / > key. You can move to the submenu by
pressing the x•B key. Then each test mode can be executed.
1. LCD test
• LCD is tested of all light-on and all light-off.
[Exiting Method of the Test Mode]
Exit the test mode by turning off the power.
x•B
[Initial Status of the Test Mode]
When the test mode is set, the LCD display appears as shown below.
. > (select), x•B (set)
LCD
LCD ALL
x
:
LCD OFF
LCD CHK
LCD ALL
LCD display (Example)
CHK START
(LCD off)
:
A B C D E STLPSP REC
6d 01 b110-56
6d
01
b110
88 8888 888888 m
YH
Iris(DSP) version : 6d
LPEC ST version : 01
SakuraR(CPU) version : 1.10
(In α version or β version, A or B is displayed)
Model code : SX56
-56
>
.
>
LCD
.
RESET MENU
.
>
>
>
>
>
>
AUDIO
.
KEY COUNT
.
SLEEP
.
USB
>
.
.
LED
BEEP
>
>
RTC
KEY
.
>
L
. >
H
x
START
TEST MODE
.
DS
CHK END
[Flow Chart of the Test Mode]
Initial status of test mode
Model code, LPEC ST,
F/W version display
MM
.
B A T T
.
Turn off the power
(Extract the batteries or DC jack)
END
TEST MODE
x
x
2. Audio test
Perform the through-playback and sine wave output.
• Contents of the submenu
DSP ST: DSP STEREO through mode
DSP MO: DSP MONO through mode
SIN: 1 kHz sine wave output mode
• Select the microphone sensitivity with the A-B
switch.
HtMtLtHtMt ...
• The VOR detection operation can be checked by the LED.
Sound : The red LED is turned on. No sound: The red LED
is turned off.
• MUTE can be set to “ON” or “OFF” with the ERASE key.
• The sound volume can be adjusted with the VOL+ key or VOL–
key during the audio test except the MUTE mode.
• In the directional microphone selection, ON/OFF of the DIRECTNL switch is performed with the DIVIDE key.
DIRECTNL switch ON : The green LED is turned on.
OFF : The green LED is turned off.
• In the audio test mode the operation is performed according to
JACK detection.
• The microphone sensitivity, sound volume and MUTE (on/off)
are displayed on the LCD.
• The microphone sensitivity selection and the VOR test are effective in the through-playback mode.
• The directional microphone selection is effective in the DSP
MONO through mode.
DSP STEREO through mode / MIC : M / MUTE : ON / VOL-LEVEL : 12
t "M / on / 12 / DSP ST"
DSP MONO through mode / MIC : H / MUTE : OFF / VOL-LEVEL : 23
t "H / oF / 23 / DSP MO"
1k sine wave output mode / MUTE : ON / VOL-LEVEL : 06 t "on / 06 / SIN"
x•B
AUDIO
DSP ST
:
DSP MONO
SIN WAVE
DSP ST
:
H
oFDSP ST12m
x
L
oFDSP M 23m
x
oFSIN WAV06
x
9
ICD-SX46/SX56/SX66
3. Sleep test
• Pressing the x•B key causes the set to enter the sleep state.
• When the HOLD . switch is ON, the LCD is turned off.
When OFF, the LCD is turned on.
• Press any keys to exit the sleep state.
8. LED test
• LEDs (OPR: red and green) are all turned on.
x•B
LED
x•B
(with HOLD .
OFF status)
SLEEP
LED ON
x LED ON (orange)
LED OFF
SLEEP SOON
x•B
(with HOLD .
ON status)
SLEEP IN
(LCD OFF)
any keys
any keys
4. Beep test
• Beep sound of 1.3 kHz or 2 kHz is output.
9. USB test
• When the menu starts the USB self-check, either presence or
absence of the Vbus is judged.
(Vbus is present: “ON VBUS”, Vbus is absent: “OFF VBUS”)
• The USB driver always works regardless of presence or absence of the USB signal only when Vbus is available during the
USB test. At this time, turning on HOLD . causes the set
to move to the suspend state. Turning off the Vbus causes the
set to return to the test menu.
• In the menumode if the Vbus is supplied, any key will not work.
Therefore the Vbus will be supplied after surely pressing the
x•B key.
x•B
BEEP
BEEP1.3K
:
x
USB
BEEP 2.0K
BEEP 1.3K
:
BEEP1.3K
HOLD .
ON
Vbus
on
x•B
VBUS OFF
VBUS ON
cut Vbus
cut Vbus
x
5. RTC test
• Perform the function test of the RTC and EEPROM.
(1) RTC EEPROM test
Confirmation of writing, reading (verifying) and erasing of
arbitrary data with the specified registers.
(2) RTC clock function test
Confirmation that RTC updates the time to the microcomputer
at one second interval.
• OK, NG judgement is performed to the test result.
When NG, it is displayed which device RTC or EEPROM
becomes NG.
(All OK : “RTC OK” / RTC NG : “RTC BAD” / EEPROM NG
: “EEP BAD”)
x•B
RTC
Suspend
mode
BEEP 2.0K
x
x
SUSPEND
10. Key durable test
• Pressing the x•B key makes the count to “------” and sets test
standby status.
Once more pressing the x•B key makes the count to “000000”
and sets the key durable test.
In this mode any key input and slide switch operation are counted
and the number is displayed.
Turn off the power to exit this mode.
x•B
KEY COUNT
x•B
KEY-----
x
any keys or slide
switches operation
KEY 000000
KEY 000001
Key durable
test
RTC OK
x
6. Key entry test
• When the any key is pressed, the entry key and the A/D converted value (hexadecimal) of the two channel keys are displayed.
• When the x key is pressed, the A/D value of the key is displayed while the key is depressed. When the key is released, the
screen returns to the test menu.
x•B
KEY
KEY oFFiFF
x
7. Battery remaining power and DC IN test
• The detected A/D value (hexadecimal) of the battery remaining
power is displayed. When DC jack is inserted, the battery mark
on the LCD is turned off.
DC jack
is inserted
x•B
bATT FF
B A T T
x
10
bATT FF
DC jack
is extracted
bATT C2
11. Menu reset
• Pressing the x•B key causes the set to enter the menu initialization standby state.
• When the following keys are all entered, the EEPROM initialization (returning setting in the menu and user name to default
value) and formatting process (deleting all message files in the
flash memory) are executed. At the same time, the WakeUp
signal is checked, too.
, ERASE ,
Check keys: VOL– , VOL+ , A-B
DIVIDE , DPC ON, DPC OFF, . ,
x•B , > , FOLDER , MENU , x ,
z REC , HOLD . ON, HOLD . OFF,
DIRECTNL ON, and DIRECTNL OFF,
VOICE UP ON, and VOICE UP OFF
ICD-SX46/SX56/SX66
• If all tests end in success, “ALL OK” is displayed. If initialization in the EEPROM is NG, “INIT. NG” appears.
• Turn off the power to exit the test mode.
x•B
RESET MENU
In the case that
the initialization
and reset operation
end correctly.
All keys
are entered
KEY PUSH
INIT
ALL OK
(0.5 sec. blinking)
x
11
ICD-SX46/SX56/SX66
SECTION 4
DIAGRAMS
Note on Schematic Diagrams:
• All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or
less are not indicated except for electrolytics and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise specified.
•
f
: internal tolerance.
• C : panel designation.
• A : B+ Line.
• Power voltage is dc 3V and fed with regulated dc power supply
from DC IN jack (J5001).
• Voltages and waveforms are dc with respect to ground under nosignal (detuned) conditions.
no mark : PLAY
[
] : REC
∗
: Impossible to measure
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F
: PB
L
: REC
* Replacement of IC6001 and IC7003 used in this set requires a
special tool.
• The voltage and waveform of CSP (chip size package) cannot be
measured, because its lead layout is different from that of conventional IC.
• Waveform
1 IC7003 <z/,
(XTAL)
3.2 Vp-p
244 ns
1 V/DIV, 100 ns/DIV
12
Note on Printed Wiring Boards:
• Y : parts extracted from the conductor side.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
* Replacement of IC6001 and IC7003 used in this set requires a
special tool.
• Lead layouts
surface
Lead layout of
conventional IC
CSP (chip size package)
ICD-SX46/SX56/SX66
4-1. BLOCK DIAGRAM – MAIN SECTION-1 –
MIC301
(DIRECTNL)
IC3004
ADC, DAC, HEADPHONE AMP
IC3005
SELECTOR
1
MIC2
L
3
26 AINL2
4
A
6
STDO
9
BICK
7
LRCK
5
STDO
STEREO
MIC3
R
25 AINR2
BCLK
LRCK
A
IC3001
5
+2.5V
REG 1
SDTI
SO
8
MAIN-2
SECTION
(Page 14)
XRST
AVDD
3
J3001
27 AINR1
MIC
MCLK
6
CDTI
4
CCLK
3
MCLK
28 AINL1
14 HPR
J3002
15 HPL
MIN 18
IC3003
POWER AMP
SP3001
(SPEAKER)
5 VO1
CSN
2
17 MOUT
-IN 4
8 VO2 XSHUT- 1
DOWN
1 PDN
Q3003
MUTE
Signal path
: PB
: REC
X6001
11.2896MHz
IC7001
SI/PO DRIVER
IC6003
CLOCK GEN.
5 XT
HPMUTE 15
3 XXT
FOUT 1
4 XCONT
MONOIN 14
10 EXTMIC
8 SPAMP
PANEL
SECTION
(Page 15)
B
XADAPDN 9
IC7004
REAL TIME CLOCK
IDSPRST 11
XBATTEN
12 XBATTEN
3 CLK
2 DATA
XREDLED 6
9 CLK
RED(REC)
D7001
OPR
XGRLED 5
7 DI
GREEN(PB)
8 DO
XIRQ 3
FOUT 5
IC7003 (1/3)
CPU
ICD-SX46/SX56/SX66
13
13
98 101
13
111
AUSIN
X0A32K
XRTCINTR
RTCCS
AUSOT
100 99
AUSCK
102 18
BEEP
12
XADACS
45
DSPSYSCLK
SPIDATA
116 115
SPICLK
HPJACK
46
MICJACK
10 CE
ICD-SX46/SX56/SX66
4-2. BLOCK DIAGRAM – MAIN SECTION-2 –
IC6001
DSP
IC7003 (2/3)
CPU
IC7002
FLASH MEMORY
FLMRB 22
STDO
45 ADASI
TSO 48
119 DSPSIN
IC6004
BCLK
16 CLE
XFLMALE 21
17 ALE
XFLMCS0 11
9 XCE
1
DSPSCK
47 LRCLK
118 DSPSIOEN
TSOEN 50
TSIEN 55
TSIOEN 158
XFLMRE 20
8 RE
XFLMWE 19
18 WE
XFLMWP 23
19 WP
XFLMCS1 35
10 NC_XCE2
DATA0-DATA7 3-10
A
SO
35 SO
XRST
TSI 52
46 MCLK
VOLTAGE
DETECT
1
Q7002
SWITCH
5 SDI
FMSDIO 160
KEYINH
C
PANEL SECTION
(Page 15)
DDCOUT
D
PANEL SECTION
(Page 15)
VBUS
E
PANEL SECTION
(Page 15)
2 SDO
FMSCK 157
2
I/O1-I/O8
IC6002
FLASH MEMORY
150 CLKIN
IC5005
29-32,
41-44
120 DSPSOT
138 XRST
MCLK
DSPCVDD
2
40 BCLK
LRCK
MAIN-1
SECTION
(Page 13)
4
TSCK 49
7 R/B
2
FLMCLE
IC8003
6 SCK
XFMWP 11
3 XWP
XFMCS 12
1 XCS
D8002
IC8001
USB CONTROLLER
3
+3.5V
REG
2
23-30 D0 - D7
USBADR0 - USBADR6 24-30
104 DSPIFREQ
REQ 159
Q7005
CN7001
(USB)
40,
A0 - A6
17-22
XUSBCS 31
45 CS
XINTUSB 109
42 INT0
XUSBVBUS 110
11 INT1
XUSBLWR 34
44 LWR
XUSBRD 32
43 RD
XUSBRST 33
46 RST
VBUS
DD+
TRON
1
2
3
4
5
3
4
6
VBUS
DD+
IN
XIN 14
X8001
12MHz
XOUT 13
RX 95
TX 96
107 XTALIN
X7001
4.096MHz
MOD2 87
108 XTAL
Signal path
Q7003
WAKEUP
WAKEUP 103
: PB
: REC
Q7004
ICD-SX46/SX56/SX66
14
14
F
PANEL SECTION
(Page 15)
ICD-SX46/SX56/SX66
4-3. BLOCK DIAGRAM – PANEL SECTION –
IC7003(3/3)
CPU
LIQUID
CRYSTAL
DISPLAY
MODULE
49-74,
77-82 SEG0 - SEG31
83-86 COM0 - COM3
S901,902,
7002,7004
FUNCTION
KEY
MAIN-2
SECTION
(Page 14)
40 KEYIN0
IC7005
XCPURST 90
2
RESET
3
S905
SEESAW
KEY
Q7001
B+
SWITCH
FLMVCC
(IC7002)
S903,904
7003
FUNCTION
KEY
MAIN-2
SECTION
(Page 14)
41 KEYIN1
XFLMPWR 97
WAKEUP
F
Q5006,5007
DSPEVDD
(IC6001, 6002, 6003)
MAIN-2
SECTION
(Page 14)
DDCOUT
D
B+
SWITCH
KEYINH
C
IC3003 VDD
DDCOUT(3.1V)
IC5001
AVDD(2.9V)
S906
5
1
4
ON
MAIN-2
SECTION
(Page 14)
VOICE UP
OFF
+2.9V
REG
43 VUPSW
E
Q5012
SWITCH
VBUS
DDCOUT
(3.1V)
VBATT
IC5003
DC/DC CONV.
DRY BATTERY
SIZE "AAA"
(IEC DESIGNATION LR03)
2PCS. 3V
4 PWM1
6 EN2
8 FB2
ON
B+
SWITCH
Q5002
SWITCH
EXT1 1
3 FB1
DSPPWR 117
S907
Q5013
L5001
D5003
IC5002
1
EXT2 10
VOLTAGE
DETECT
42 MICSEL
L5002
DIRECTNL
DSPCVDD(1.6V)
OFF
Q5003
SWITCH
D5005
D5004
S908
ON
44 XDPCSW
Q5001
SWITCH
BATT 39
DPC
MAIN-1
SECTION
(Page 13)
OFF
B
J5001
DC IN 3V
XBATTEN
Q5009
Q5005
DC DET
S7001
Q5010, 5011
SWITCH
ON
112 HOLDSW
HOLD
3
XDCINDET 113
OFF
ICD-SX46/SX56/SX66
15
15
ICD-SX46/SX56/SX66
4-4. PRINTED WIRING BOARD – AUDIO BOARD (SIDE A) –
:Uses unleaded solder.
A
(SIDE A)
IC6001
*
CSP (Chip size package)
3
MAIN BOARD
CN7004
(Page 21)
40
2
39
1
IC3004
1
IC6003
4
4
5
6
3
4
3
6
IC3005
AUDIO BOARD
•
1
1
IC6004
IC3001
4
3
IC3003
5
1
11
(11)
1-867-746-
MIC301
J3001
MIC
PLUG IN POWER
• Semiconductor
Location
ICD-SX46/SX56/SX66
16
16
Ref. No.
Location
IC3001
IC3003
IC3004
IC3005
IC6001
IC6003
IC6004
F-11
F-13
C-12
D-14
C-3
C-6
D-6
Q3003
E-13
ICD-SX46/SX56/SX66
4-5. SCHEMATIC DIAGRAM – AUDIO BOARD (SIDE B) –
AUDIO BOARD
•
(SIDE B)
IC6002
J3002
i
ERASE
OPR
1
4
11
1
B
A-B
/PRIORITY
1-867-746-
DIVIDE/
MIC2/3
STEREO
L/R
SW BOARD
CN7006
(Page 24)
ICD-SX46/SX56/SX66
17
17
11
(11)
ICD-SX46/SX56/SX66
4-6. SCHEMATIC DIAGRAM – AUDIO BOARD (1/2) –
• See page 26 for IC Block Diagrams.
R3032
100
TP3005
R3004
100
R3001
2.2k
MIC301
(DIRECTNL)
R1013
2.2k
CN3001
FPC MIC 4P
R3002 0
C3002
0.1
C3009
0.01
C3004
1
TP1001
C3008
0
R3011
100k
C3005
10
6.3V
IC3005
TC7PA53FU(TE85L
MIC2
R2013 TP2001
2.2k
TP3003
R3022
0
MIC3
C1009
0.01
C2009
0.01
C1001
0.1
R1015 0
C2008
1
C1008
1
C3001
1
R1001
100
IC3001
XC6204B252MR
C1003
1
R2007
100
C1007
0
C1004
10
6.3V
R1007
100
C3021
0.1
C3020
10
6.3V
R3016
220
C3022
0.1
R3023
470k
C3023
0.01
R3031
0
R3017
100k
C2001
0.1
R2001
100
R2008
4.7k
R1008
4.7k
R3003
100k
C2003
1
C3017
0.1
C2004
10
6.3V
C2007
0
R2015
0
C3018
2.2
6.3V
J3001
MIC JACK
R3025
4.7k
FB2001
PLUG IN POWER
C3024
0.1
C3010
nm
R2014 0
C3019
0.1
FB1001
IC3004
AK4569VN-L
R1014 0
FB3001
C2010 0.1
FB3002
J3002
HP JACK
R2010 4.7
C2012 47 6.3V
FB2002
C1010 0.1
C3025
0.1
FB1002
R2011
2.2
C2011
0.22
R1011
2.2
C1011
0.22
TP3004
FB3006
R1009
1k
R2009
1k
C1012
47
6.3V
R1012
1k
R2012
1k
R1010
4.7
R3021
220k
R3020
10
C3013 220p
Q3003
NTHD4508NTIG
C3026
1000p
R3013 150k
R3018
100k
R3015
22k
R3027
10k
C3016
0.022
IC3003
MM3111AWLE
FB3004 0H
C3014
0.022
C3027
nFm18pS105
R3029
47k
R3014
100k
TP3002
C3011
0.1
SP3001
(SPEAKER)
TP3001
C3015
0.47
R3030
100k
R3026
2.2k
FB3005 0H
C3028
nFm18pS105
ICD-SX46/SX56/SX66
18
18
ICD-SX46/SX56/SX66
4-7. SCHEMATIC DIAGRAM – AUDIO BOARD (2/2) –
• See page 19 for IC Pin Function Description.
R6023
47
IC6003
NJU6366AF1(TE1)
R6022
47
R6004
470k
TP6012
C6006
0.1
R6025
0
R6009 100k
TP6011
TP6001
TP6003
C6007
1000p
TP6004
R6013
100k
R6014
100k
R6015 TP6005
100k
R6017 100k
R6026 R6027
100k
100k
R6016 100k
C6003 0.1
TP6002
R6003 470k
TP6013
X6001
11.2896MHz
IC6002
M25P10-AVMN6TP
TP6006
R6018
100k
TP6007
R6019
100k
C6010
100p
CN7003
B TO B
TP6008
RB6002
100k
TP6009
TP6010
R6006 100k
R6007 100k
C6001
1
IC6001
OPR
RB6001
100k
R7003
2.2k
D7001
LC-375HR1YG-D-TS
-DA2
R6020
100k
C6002
1
R7002
470
R6005
100k
R6021
100k
R6001
470k
CN7005
FPC SW 11P
R3028
220
R6002
470k
R7052
3.3k
0.5%
R6012 470k
R7051
4.7k
0.5%
S7002
S7004
C6014
0.1
ERASE
/PRIORITY
R6008
470k
R6010
470k
R6011
470k
IC6004
TC7S04FU(TE85R)
ICD-SX46/SX56/SX66
19
19
DIVIDE
S7003
ICD-SX46/SX56/SX66
4-8. PRINTED WIRING BOARD – MAIN BOARD (SIDE A) –
•
MAIN BOARD (SIDE A)
IC7001
1
8
IC7003
4
5
CSP (Chip size package)
*
IC5003
5
3
4
IC5001
8
HOLD.
1
5
4
1
1
2
ON
IC7005
DRY BATTERY
SIZE "AAA"
(IEC DEESINATION LR03)
2PCS 3V
IC5002
1
IC5005
2
4
40
1
3
1-867-745-
11
(11)
J5001
DC IN 3V
LCD MODULE
• Semiconductor
Location
ICD-SX46/SX56/SX66
20
20
Ref. No.
Location
D5002
D5003
D5004
D5005
D5007
D5009
A-4
C-8
D-7
D-5
D-3
C-3
IC5001
IC5002
IC5003
IC5005
IC7001
IC7003
IC7005
D-10
E-6
D-9
F-11
B-16
C-13
E-15
Q5002
Q5003
Q5006
Q5007
Q5009
Q5012
D-8
E-8
C-11
B-11
D-4
E-7
ICD-SX46/SX56/SX66
4-9. PRINTED WIRING BOARD – MAIN BOARD (SIDE B) –
•
A
MAIN BOARD (SIDE B)
AUDIO BOARD
CN7003
(Page 16)
2
3
40
IC8003
1
IC7004
1
2
IC8001
39
FB7001
IC7002
1
5
1-867-745-
• Semiconductor
Location
ICD-SX46/SX56/SX66
21
21
Ref. No.
D7004
D8001
D8002
Location
C-4
B-17
B-17
IC7002
IC7004
IC8001
IC8003
E-7
C-5
C-15
B-17
Q5001
Q5005
Q5010
Q5011
Q7001
Q7002
B-7
C-17
C-18
D-18
G-3
C-7
11
(11)
ICD-SX46/SX56/SX66
4-10. SCHEMATIC DIAGRAM – MAIN BOARD (1/2) –
C8003
18p X8001
12MHz
R8009
220
C8002
0.1
NAND01GW3B2AN6F : SX46
C8005
18p
R8006
1M
R8022
470
IC8003
XC62FP3502MR
IC7002
*1
D8001
RB520S-30TE61
C8006
0.1
TP7014
R8007
470M
R8010
100k
R7017
0
R7010
10k
R7040
470k
IC8001
M66291GP-2
R7042
470k
C7003
0.1
C8009
4.7 10V
D8002
ISS352-TP3
R8011
100k
R8012
100k
R8020
1
R8013 2.2k
R8021
4.7k
C7004
0.1
TP7002
VBUS(5V)
C8010
1
FB7001
OH
R8015 22
C8001
0.1
R8016 22
C8007
0.1
R7048
1k
C7022
1
R8003 100k
Q7001
ND5356AP
R7011
470k
R7009
1M
C8004
1000p
R8004 100k
R7039
1k
R8005
470k
R7044
1k
R8001
470k
R7027
100k
R8002
470k
D7004
R7030 1SS352-TPH3
100
Q7005
UN9214J-(K8).SO
C7016
47 10V
IC7004
RX-4591CF
Q7004
UN9214J-(K8).SO
C7017
0.1
ICD-SX46/SX56/SX66
22
22
TP7001
TP7003
R7047
1k
FB7002
OH
CN7001
5P
USB
ICD-SX46/SX56/SX66
4-11. SCHEMATIC DIAGRAM – MAIN BOARD (2/2) –
• See page 12 for Waveform.
• See page 31 for IC Pin Function Description.
R3024
470k
C7023
0.01
R7043
470k
C7001
0.1
X7001 4.096MHz
HOLD
S7001
R7015 1k
TP7005
R7025
470k
R7019 0
TP7010
R7012
470k
TP7006
C7009
100p
R7038
100k
C7021
0.1
IC7001
BU2090FS-E2
C7010 0.1
R7028 1k
R7023
470k
IC7005
R3130N28EA-TR
C7020
1000p
TP5004
AVDD
(2.9V)
IC5001
R1160N291B-TR-F
CN7004
B TO B
R7029
100k
R7031
100k
R7034
100k
C7019
100p
C5005
10
6.3V
IC5005
XC61CS23XXNR
C5009
0.1
TP7004
IC7003
FB91233LLGA
-G-109E1
R7001 1M
C5020
0.1
C5014
47 6.3V
R5012
330k
0.5%
TP5006
DSPCVDD
(1.6V)
R5009
470k 0.5%
R5010
150k
0.5%
D5004
RB168M-30TR
C5012
100p
C7005 0.1
L5002
Q5003
XP152AI2C0MR
R7037 0
IC5003
XC9502B092AR
R7041 0
C7018 0.1
TP5005
DDCOUT
3.1V
Q5007
NDS356AP
R5006
680k
0.5%
R7004 0
C5022
4.7
10V
Q5012
2SK3019TL
R5016
470k
C5021
0.1
R7020 1k
R7054 1k
R5002 33k
Q5002
XP151A12A2MR
R5024
2.2M
R5015
470k
R5008
680k
0.5%
C5007
1 CH
R5007
470k
0.5%
TOTAL CURRENT
PLAY : 55mA
REC : 65mA
STOP : 0.1mA
R7022 1k
C7006
0.1
C5001
0.1
R5001
100k
0.5%
L5001
R5025
1M
C5016
33
10V
Q5006
2SK3019TL
C7011
0.1
C5011 22p CH
R5004
0
R5017
1M
D5003
RB160M-30TR
TP5010
W5001
TP5001
Q5013
NTHS2101PT1G
IC5002
SIF77600M0A000L
R5005
470k
Q5001
3LP01S-K-TL-E
C5003
47
10V
Q5011
3LP01S-K-TL-E
TP7012
TP7008
TP7009
C7015
1000p
T5001
COMMON MODE
CHOKE
R5011
2.2k
Q5005
2SC4617TL-QR
R5013
1k
0.5%
R7008 1k 0.5%
CN7002
18P FPC_LCD_36P
Q5009
TPCF8201
(T5RSONY.F)
R7007 1k 0.5%
TH5001
THERMISTOR
D5009
MAZS120008SO
J5001
C5004
0.1
D5002
MA2ZD02001SO
D5007
MAZS120008SO
(
ICD-SX46/SX56/SX66
23
23
W5002
C5002
0.1
TP5003
R5021
470k
R7033
100k
TP7013
R7006 2.2k
TP5008
D5005
MA2ZD02001SO
R5022
470k
TP7007
C7012 0.1
C7013 0.1
Q5010
2SK3019TL
R5014
100k
TP5002
Q7003
3LP01S-K-TL-E
R7016 220k
R7014 10k 0.5%
C5017 47 10V
R7032
100k
R7050
1k
Q7002
3LP01S-K-TL-E
R7013 10k 0.5%
C5006
0.1
C5010 0.1
R7046
470k
R7045
470k
TP5007
C7014 0.1
R7053
470k
C5018 47 10V
TP5009
R5003
470k
) : REC
ICD-SX46/SX56/SX66
4-12. PRINTED WIRING BOARD – SW BOARD –
•
(SIDE A)
SW BOARD
B
AUDIO BOARD
CN7005
(Page 17)
11
1-860-642- (11)
ON
OFF
VOICE UP
DPC
SW BOARD
ON
OFF
ON
OFF
DIRECTNL
(SIDE B)
x•N
>
.
MENU
FOLDER
STOP
x
VOLUME
ICD-SX46/SX56/SX66
24
24
z
REC/REC PAUSE
1-860-642-
11
(11)
ICD-SX46/SX56/SX66
4-13. SCHEMATIC DIAGRAM – SW BOARD –
CN7006
11P
R907
1k 0.5%
C902 4700p
MENU
S905
FOLDER
R908
22k
0.5%
C901
4700p
R904
33k
0.5%
ET7001
R909
33k
0.5%
R905
22k
0.5%
R901
2.2k
0.5%
S901
VOL–
R902
3.3k
0.5%
S902
VOL+
S903
STOP
R903
4.7k
0.5%
S904
REC/REC PAUSE
S906
VOICE UP
ON–OFF
ICD-SX46/SX56/SX66
25
25
S907
DIRECTNL
ON–OFF
S908
ON–OFF
ICD-SX46/SX56/SX66
• IC Block Diagrams
– AUDIO Board –
– MAIN Board –
IC5003 XC9502B092AR
IC3003 MM3111AWLE
SHUTDOWN 1
IC7004 RX-4591CF
8 VO2
BIAS
BYPASS 2
7 GND
6 VDD
+IN 3
32.768kHz
PWM/PFM
CONTROLLER1
EXT1 1
10
VDD 1
EXT2
OSC
PWM
COMPARATOR1
5 VO1
-IN 4
PWM/PFM
CONTROLLER2
VDD 2
PWM
COMPARATOR2
FB1 3
9
GND
FOE 2
8
FB2
XIRQ 3
7
PWM2
6
EN2
DIVIDER
CLOCK
AND
CALENDAR
FOUT
CONTROLLER
TIMER
REGISTER
INTERRUPTS
CONTROLLER
ARARM
REGISTER
BUS
INTERFACE
CIRCUIT
CONTROL
REGISTER
AND
SYSTEM
CONTROLLER
CE
10
CE
CLK
9
CLK
DO
8
DO
DI
7
DI
6
GND
XXT
VDD
FOUT
IC6003 NJU6366AF1 (TE1)
3
2
1
ERROR AMP1 RAMP WAVE
GENERATOR1
PWM1 4
VREF1=0.9V
WITH SOFT START1,
EN1
EN1 5
RF
OSC
GENERATOR
1/2
VREF1=0.9V
WITH SOFT START2,
EN2
DI
DO
CLK
CE
T1 4
FOUT 5
EN2 TO
INTERNAL CIRCUIT
EN1 TO
INTERNAL CIRCUIT
1/2
1/2
CD
3-STATE
BUFFER
5
14
13
6
7
DACK1
8
9
TC1
10
INT1
11
IVDD
12
ICD-SX46/SX56/SX66
26
26
36
GND
35
IVDD
34
D11
33
D10
32
D9
31
D8
30
D7
29
D6
28
D5
27
D4
26
D3
25
D2
INT0
HWR/BYTE
D15/A0
D14
D13
D12
USB-IP
OSCILLATION
BUFFER
/48MHzPLL
VBUS
INPUT CIRCUIT
D+ PIN PULLUP
CIRCUIT
TRANSFER
CONTROLLER
4
3
DREQ1
37
INTERRUPT CONTROLLER
6
TEST
38
I/O BLOCK
5
TRON
39
ENDPOINT
CONTROLLER
SERIAL
INTERFACE
ENGINE
(SIE)
USB
TRANSCEIVER
BUS
INTERFACE
UNIT
(BIU)
FIFO MEMORY CONTROLLER
FIFO MEMORY
13
14
15
16
17
18
19
20
21
22
23
24
11
VBUS
40
8-10
4
41
D1
D+
42
D0
3
43
A6
D-
44
A5
2
45
A4
GND
46
A3
4 5 6 7 8
XLIGHT1
XGRLED
XREDLED
XSTMIC
SPAMP
5 VCC
4 OUT
3
CLK
NC 1
IN 2
GND 3
1 2
VSS
DATA
IC6004 TC7S04FU(TE85R)
1
47
A2
VSS
12 BIT
STORAGE
REGISTER
CVDD
OUTPUT
BUFFER
(OPEN DRAIN)
48
A1
XT
CONTROL
CIRCUIT
12 BIT
SHIFT
REGISTER
CVDD
XCONT
16 15 14 13 12 11 10 9
GND
6
XIN
5
XOUT
4
RD
IC8001 M66291GP-2
VDD
HPMUTE
XLIGHT2
MONOMIC
XBATTEN
XDSPRST
XFLMPWR
XADAPDN
IC7001 BU2090FS-E2
LWR
D
CS
C
RST
B
DREQ0
A
DACK0
CG
RAMP WAVE ERROR AMP2
GENERATOR2
ICD-SX46/SX56/SX66
• IC Pin Function Description
AUDIO Board IC6001 uPD77213F1-101-DA2 (DSP)
Pin No.
Pin Name
I/O
1 to 3
NC
—
Description
4
EVDD
—
I/O power supply (3.1V)
5
XADACS
O
AD/DA chip select (Not used) (fixed at “L”)
6
ADACCLK
I/O
Not used
AD/DA clock (Not used) (fixed at “L”)
7
ADACDTI
I
AD/DA data input (Not used) (fixed at “L”)
8
ADACDTO
O
AD/DA data output (Not used) (fixed at “L”)
9
MICPWR
O
Microphone power supply control (Not used) (fixed at “L”)
10
GND
—
Ground terminal
11
XFMWP
O
Boot flash ROM write protect
12
XFMCS
O
Boot flash ROM chip select
13
MICSENSE
O
Micropone sensitivity select (Not used) (fixed at “L”)
14
GND
—
Ground terminal
15
NC
—
Not used
16
EVDD
—
I/O power supply (3.1 V)
17
HD1
I/O
Host data bus (Not used)
18
HD2
I/O
19
HD0
I/O
20
HD3
I/O
21
HD5
I/O
22
HD4
I/O
23
GND
—
Ground terminal
24
IVDD
—
Core power supply (1.6 V)
25
HD7
I/O
26
HD6
I/O
27
GND
—
Ground terminal
28
EVDD
—
29
XHCS
I
Host chip select (Pull-up) (fixed at “H”)
30
HA1
I
Host data access 1 (Pull-down) (fixed at “L”)
31
XHWR
I
Host write (Pull-up) (fixed at “H”)
32
HA0
I
Host data access 0 (Pull-down) (fixed at “L”)
33
XHRD
I
Host read (Pull-up) (fixed at “H”)
34
TIMOUT
O
Not used
35
SO
O
Serial data output
36
XHWE
O
Host write enable (Not used)
37
XHRE
O
Host read enable (Not used)
38
GND
—
Ground terminal
39
EVDD
—
40
BCLK
I/O
Bit clock
41 to 44
NC
—
Not used
45
ADASI
I
ADA serial data input
46
MCLK
I
Master clock
47
LRCLK
I/O
48
TSO
O
Time sharing serial data output
49
TSCK
I
Time sharing serial clock input
50
TSOEN
I
Time sharing serial output enable
51
GND
—
52
TSI
I
Clock for L-ch and R-ch (H: L-ch, L: R-ch)
Ground terminal
Time sharing serial data input
27
ICD-SX46/SX56/SX66
Pin No.
Pin Name
I/O
Description
53
TSIAK
O
54
TSORQ
O
Time sharing serial output request (Note used)
55
TSIEN
I
Time sharing serial input enable
56
EVDD
—
57
MA1
O
Memory address bus 1 (Not used)
Time sharing serial input response (Not used)
58
MA0
O
59
GND
—
Ground terminal
60
IVDD
—
61
MA2
O
62
MA4
O
63
GND
—
Ground terminal
64
MA3
O
65
MA7
O
66
MA5
O
67
MA8
O
68
MA6
O
69
MA9
O
70
MA10
O
Memory address 10 (Not used)
71
GND
—
Ground terminal
72
EVDD
—
73
MA11
O
74
MA12
O
75
MA14
O
76
MA13
O
77
MA16
O
78
MA15
O
79
EVDD
—
80
MA17
O
81 to 84
NC
—
Not used
85
EVDD
—
86
MA18
O
87
MA19
O
88
XMHOLDAK
O
Memory bus hold response (Not used)
89
XMRD
O
Memory read-out (Not used)
90
XMHOLDRQ
I
Memory bus hold request (Pull-up) (fixed at “H”)
91
GND
—
92
EVDD
—
93
XMWAIT
I
Memory access weight (Pull-up)
94
XMWR
O
Memory write (Not used)
95
GND
—
Ground terminal
96
IVDD
—
97
XMBSTB
O
98
MD0
I/O
28
Ground terminal
Memory bus strobe (Not used)
Memory data bus (Not used)
99
GND
—
Ground terminal
100
MD3
I/O
101
MD1
I/O
102
MD4
I/O
103
MD5
I/O
104
MD6
I/O
ICD-SX46/SX56/SX66
Pin No.
Pin Name
I/O
Description
105
MD2
I/O
106
MD8
I/O
107
GND
—
Ground terminal
108
EVDD
—
109
MD7
I/O
110
MD13
I/O
111
MD10
I/O
112
MD11
I/O
113
MD9
I/O
114
MD14
I/O
115
GND
—
Ground terminal
116
MD15
I/O
117
MD12
I/O
118
TICE
O
Test ICE
119
TMS
I
Test mode selection
120
EVDD
—
121
GND
—
Ground terminal
122
TDO
O
Test data output
123 to 126
NC
—
Not used
127
XTRST
I
Test reset
128
TCK
I
Test clock input
129
EVDD
—
130
IC
—
131
TDI
I
Test data input
132
STOPS
O
Stop (Open)
133
CSTOP
I
Clear stop mode (Pull-down) (fixed at “L”)
Internal connection (Not used)
134
IC
—
Internal connection (Not used)
135
GND
—
Ground terminal
136, 137
PLL0,PLL1
I
138
WRSTXRST
I
139
GND
—
Ground terminal
140
IVDD
—
141
PLL3
I
PLL rate setting 3
142
HALTS
O
HALT
143
GND
—
Ground terminal
144, 145
IVDD
—
146
PLL2
I
PLL rate setting 2
147
GND
—
Ground terminal
148
EVDD
—
149
CLKOUT
O
Clock output
PLL rate setting 0 and 1
Reset
150
CLKIN
I
Clock input
151
BOOT1
I
Boot mode 1 (fixed at “H”)
152
GND
—
153
BOOT3
I
154
BOOT0
I
Boot mode 0 (fixed at “L”)
155
GND
—
156
BOOT2
I
157
FMSCK
I/O
Boot flash ROM serial clock
158
TSIOEN
I
Ground terminal
Ground terminal
SIO enable
29
ICD-SX46/SX56/SX66
Pin No.
Pin Name
I/O
159
REQ
O
160
FMSDIO
I/O
Boot flash ROM serial data
161 to 164
NC
—
Not used
30
Description
Request
ICD-SX46/SX56/SX66
MAIN Board IC7003 MB91233LLGA-G-109E1 (CPU)
Pin No.
Pin Name
I/O
1
DSPSCK
O
2
FLMCLE
O
3 to 10
DATA0 to 7
I/O
Description
Serial clock output for DSP
Command latch enable signal output for FLASH
Data input/output to FLASH and USB
11
XFLMCS0
O
Chip enable signal output for FLASH
12
DSPSYSCK
O
System clock control signal output for DSP
13
X0A32k
I
32KHz vibration terminal (input) (fixed at “H”)
14
X1A32k
—
32KHz vibration terminal (input)
15
VCC3BCK
—
Internal logic backup voltage terminal
16
VSS
—
Ground terminal
17
VCC3LGC
—
Internal logic voltage terminal
18
BEEP
O
Beep output
19
XFLMWE
O
Write enable signal output for FLASH
20
XFLMRE
O
Read enable signal output for FLASH
21
XFLMALE
O
Address latch enable signal output for FLASH
22
FLMRB
I
Ready/Busy signal input from FLASH
23
XFLMWP
O
Write protect signal output to FLASH
24 to 30
USBADR0 to 6
O
Address signal output to USB control
31
XUSBCS
O
Chip select signal output to USB control
32
XUSBRD
O
Read strobe signal output to USB control
33
XUSBRST
O
Reset signal output to USB control
34
XUSBLWR
O
Low write strobe signal output to USB control
35
XFLMCS1
O
Chip enable signal output for FLASH (Not used)
36
AVCC
—
Analog power supply
37
AVREF
—
Reference voltage terminal
38
AVSS
—
39
BATT
I
Battery voltage detect signal input
40
KEYIN0
I
Key 0 A/D input
41
KEYIN1
I
Key 1 A/D input
42
MICSEL
I
Directivity microphone switch signal input
43
VUPSW
—
44
XDPCSW
I
DPC switch signal input
45
MICJACK
I
External microphone detect signal input
46
HPJACK
I
Headphone detect signal input
47
VSS
—
Ground terminal
Ground (Analog) terminal
Voice up switch signal input
48
AVCC3IO
—
Voltage terminal
49 to 74
SEG0 to 25
O
LCD segment output terminal
75
DVCC
—
Voltage terminal
76
DVSS
—
Ground terminal
77 to 82
SEG26 to 31
O
LCD segment output terminal
83 to 86
COM0 to 3
O
LCD common output terminal
87
MOD2
I
Mode input terminal
88
MOD1
I
Mode input terminal (fixed at “L”)
89
MOD0
I
Mode input terminal (fixed at “L”)
90
XCPURST
I
CPU external reset signal input
91 to 94
LCDV0 to 3
—
LCD reference voltage terminal
95
RX
I
FLASH overwrite RX
96
TX
O
FLASH overwrite TX
97
XFLMPWR
O
FLASH power supply control signal output (L:ON)
31
ICD-SX46/SX56/SX66
Pin No.
Pin Name
I/O
Description
98
AUSIN
I
Serial data input from RTC
99
AUSOT
O
Serial data output to RTC, ADC and DAC
100
AUSCK
O
Serial clock output to RTC, ADC and DAC
101
RTCCS
O
Chip select signal output to RTC
102
XADACS
O
Chip select signal output to ADC, DAC
103
WAKEUP
I
WAKE UP interrupt input
104
DSPIFREQ
I
DSP I/F interrupt request
105
DVCC
—
106
DVSS
—
107
XTALIN
I
108
XTAL
O
Main vibration terminal (input)
109
XINTUSB
I
USB driver interrupt request input (L:active)
110
XUSBVBUS
I
USB driver VBUS detect interrupt request input
111
XRTCINTR
I
RTC interrupt input
112
HOLDSW
I
Hold switch input (interrupt:on)
113
XDCINDET
I
AC adaptor detect input (interrupt:on)
114
FLM COUNT
I
DIN MUTE interrupt (Not used)
115
SPIDATA
O
Data output to IC7001
116
SPICLK
O
Clock output to IC7001
Voltage terminal
Ground terminal
Main vibration terminal (input)
117
DSPPWR
O
DSP power supply circuit control output
118
DSPSIOEN
O
DSP SIO enable output
119
DSPSIN
I
DSP serial data input
120
DSPSOT
O
DSP serial data output
121
NC
—
Not used
122
VCC3
—
Voltage terminal
123, 124
NC
—
Not used
125
AVRL
—
Ground terminal
126 to 128
NC
—
Not used
32
ICD-SX46/SX56/SX66
Ver. 1.3
SECTION 5
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• The mechanical parts with no reference
number in the exploded views are not supplied.
5-1.
•
Items marked “*” are not stocked since they are •
seldom required for routine service.
Some delay should be anticipated when ordering
these items.
Abbreviation
CEW : France model
CND : Canadian model
CH
: Chinese model
KR
: Korean model
JE
: Tourist model
CASE BLOCK ASSY
8
1
5
2
not
supplied
6
3
8
4
chassis section
A
7
9
17
12
16
13
A
18
11
15
18
14
10
Ref. No.
Part No.
Description
Remark
1
1
1
1
1
A-1149-291-A
A-1149-437-A
A-1149-439-A
A-1149-441-A
A-1149-445-A
CASE BLOCK ASSY (SX46: US, CND, E)
CASE BLOCK ASSY (SX56: AEP, UK)
CASE BLOCK ASSY (SX56: CH, KR)
CASE BLOCK ASSY (SX66)
CASE BLOCK ASSY (SX46: AEP, UK, CEW)
1
1
2
3
4
A-1153-520-A
A-1159-738-A
3-243-311-01
3-243-306-01
2-655-904-01
CASE BLOCK ASSY (SX56: E, JE)
CASE BLOCK ASSY (SX46: CH, KR)
CLIP
BRACKET (CLIP)
KNOB (HOLD) (SX46/SX56)
4
5
5
6
6
2-655-904-11
2-655-916-01
2-655-916-11
2-655-917-01
2-655-917-11
KNOB (HOLD) (SX66)
COVER (JACK) (US, CND, AEP, JE, CEW)
COVER (JACK) (CH, KR)
LID (CONNECTOR) (SX46/SX56)
LID (CONNECTOR) (SX66)
7
3-233-058-01 SHAFT (HAND STRAP)
Ref. No.
Part No.
Description
8
8
9
9
3-254-014-01
3-254-014-11
3-225-873-25
3-225-873-27
SCREW (SX46/SX56)
SCREW (SX66)
SCREW (M1.4) (SX46/SX56)
SCREW (M1.4) (SX66)
10
11
11
11
12
3-221-591-01
2-655-911-01
2-655-911-11
2-655-911-21
X-3382-358-4
NUT (M1.4)
LID, BATTERY CASE (SX56)
TERMINAL (+/–) ASSY, BATTERY
13
13
14
14
15
A-1149-226-A
A-1157-601-A
2-655-910-01
2-655-910-11
2-655-908-01
SW BOARD, COMPLETE (SX66)
SW BOARD, COMPLETE (SX46/SX56)
BELT, ORNAMENTAL (SX46/SX56)
BELT, ORNAMENTAL (SX66)
BUTTON (VOL) (SX46/SX56)
15
16
16
17
18
2-655-908-11
2-655-909-01
2-655-909-11
3-234-449-09
2-655-923-01
BUTTON (VOL) (SX66)
BUTTON (RS) (SX46/SX56)
BUTTON (RS) (SX66)
SCREW (M1.4)
SHEET (ORNAMENTAL BELT)
Remark
33
ICD-SX46/SX56/SX66
5-2.
CHASSIS BLOCK ASSY
59
not
supplied
51
MIC2/3
LCD
52
54
55
60
56
SP3001
58
57
53
Ref. No.
Part No.
Description
51
52
53
54
55
2-655-913-01
A-1147-222-A
2-655-919-01
2-655-914-01
A-1147-228-A
HOLDER (LCD)
AUDIO BOARD, COMPLETE
SHEET (SPEAKER)
CHASSIS
MAIN BOARD, COMPLETE (SX66)
55
55
56
A-1148-737-A MAIN BOARD, COMPLETE (SX56)
3-250-332-01 CAP (TERMINAL)
34
Remark
Ref. No.
Part No.
Description
57
58
2-655-928-01 TERMINAL (+), BATTERY
2-655-912-01 COVER (CHASSIS)
59
60
LCD
MIC2/3
SP3001
2-655-920-01
2-655-921-01
1-802-005-11
1-479-549-11
1-825-993-11
CUSHION (LCD-B)
SHEET (MEMORY), INSULATING
DISPLAY PANEL, LIQUID CRYSTAL
MICROPHONE UNIT
SPEAKER (1.6cm)
Remark
ICD-SX46/SX56/SX66
Ver. 1.3
AUDIO
SECTION 6
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
•
•
•
•
RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
Accessories are given in the last of this parts
list.
CAPACITORS
uF: µF
COILS
uH: µH
•
SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
Abbreviation
CEW : France model
CND : Canadian model
CH
: Chinese model
KR
: Korean model
JE
: Tourist model
•
When indicating parts by reference number,
please include the board name.
Ref. No.
Part No.
Description
Remark
A-1147-222-A AUDIO BOARD, COMPLETE
*********************
< CAPACITOR >
10V
6.3V
6.3V
6.3V
Ref. No.
Part No.
Description
Remark
C6001
C6002
1-125-837-91 CERAMIC CHIP
1uF
1uF
10%
10%
6.3V
6.3V
C6003
C6006
C6007
C6010
C6014
1-125-777-11
1-125-777-11
1-164-937-11
1-164-931-11
1-125-777-11
0.1uF
0.1uF
0.001uF
100PF
0.1uF
10%
10%
10%
10%
10%
10V
10V
50V
50V
10V
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
C1001
C1002
C1003
C1004
C1007
1-125-777-11
1-125-837-91
1-125-837-91
1-117-919-11
1-218-990-81
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
SHORT CHIP
0.1uF
1uF
1uF
10uF
0
10%
10%
10%
20%
C1008
C1009
C1010
C1011
C1012
1-125-837-91
1-164-943-81
1-125-777-11
1-127-715-91
1-110-569-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
1uF
0.01uF
0.1uF
0.22uF
47uF
10%
10%
10%
10%
20%
6.3V
16V
10V
16V
6.3V
CN3001 1-817-570-21 CONNECTOR, FPC (ZIF) 4P
CN7003 1-779-665-41 CONNECTOR, BOARD TO BOARD 40P
C2001
C2002
C2003
C2004
C2007
1-125-777-11
1-125-837-91
1-125-837-91
1-117-919-11
1-218-990-81
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
SHORT CHIP
0.1uF
1uF
1uF
10uF
0
10%
10%
10%
20%
10V
6.3V
6.3V
6.3V
D7001
C2008
C2009
C2010
C2011
C2012
1-125-837-91
1-164-943-81
1-125-777-11
1-127-715-91
1-110-569-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
1uF
0.01uF
0.1uF
0.22uF
47uF
10%
10%
10%
10%
20%
6.3V
16V
10V
16V
6.3V
C3001
C3002
C3004
C3005
C3008
1-125-837-91
1-125-777-11
1-125-837-91
1-117-919-11
1-218-990-81
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
SHORT CHIP
1uF
0.1uF
1uF
10uF
0
10%
10%
10%
20%
6.3V
10V
6.3V
6.3V
C3009
C3011
C3013
C3014
C3015
1-164-943-81
1-125-777-11
1-164-933-11
1-107-819-11
1-125-891-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
220PF
0.022uF
0.47uF
10%
10%
10%
10%
10%
16V
10V
50V
16V
10V
C3016
C3017
C3018
C3019
C3020
1-107-819-11
1-125-777-11
1-113-600-11
1-125-777-11
1-117-919-11
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
TANTAL. CHIP
0.022uF
0.1uF
2.2uF
0.1uF
10uF
10%
10%
20%
10%
20%
16V
10V
6.3V
10V
6.3V
C3021
C3022
C3023
C3024
C3025
1-125-777-11
1-125-777-11
1-164-943-81
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.01uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
10V
10V
16V
10V
10V
C3026
C3027
C3028
1-164-937-11 CERAMIC CHIP 0.001uF 10%
1-234-939-21 FILTER, EMI REMOVAL (SMD)
1-234-939-21 FILTER, EMI REMOVAL (SMD)
50V
< CONNECTOR >
< DIODE >
6-500-122-01 DIODE CL-375HR/YG-D-TS (OPR)
< FERRITE BEAD >
FB1001
FB1002
FB2001
FB2002
FB3001
1-469-084-21
1-469-084-21
1-469-084-21
1-469-084-21
1-469-084-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0mH
0mH
0mH
0mH
0mH
FB3002
FB3004
FB3005
FB3006
1-469-084-21
1-400-050-11
1-400-050-11
1-400-050-11
FERRITE
0mH
INDUCTOR, FERRITE BEAD
< IC >
IC3001
IC3003
IC3004
IC3005
IC6001
6-703-074-01
6-707-089-01
6-708-899-01
6-705-673-01
6-803-583-01
IC
IC
IC
IC
IC
XC6204B252MR
MM3111AWLE
AK4569VN-L
TC7PA53FU (TE85L.F)
uPD77213F1-101-DA2
IC6002
IC6003
IC6004
6-708-624-01 IC M25P10-AVMN6TP
6-703-867-01 IC NJU6366AF1 (TE1)
8-759-058-58 IC TC7S04FU (TE85R)
< JACK >
J3001
J3002
1-818-048-11 JACK (SMALL TYPE) (MIC/PLUG IN POWER)
1-817-346-21 JACK (i)
< MICROPHONE >
MIC301 1-542-661-11 MICROPHONE, ELECTRET CAP
< TRANSISTOR >
Q3003
6-550-859-01 TRANSISTOR
NTHD4508NT1G
35
ICD-SX46/SX56/SX66
AUDIO
Ref. No.
MAIN
Part No.
Description
Remark
< RESISTOR >
Ref. No.
Part No.
Description
R6014
R6015
R6016
R6017
1-218-977-11
1-218-977-11
1-218-977-11
1-218-977-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100K
100K
100K
100K
5%
5%
5%
5%
Remark
1/16W
1/16W
1/16W
1/16W
R6018
R6019
R6020
R6021
R6022
1-218-977-11
1-218-977-11
1-218-977-11
1-218-977-11
1-218-937-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100K
100K
100K
100K
47
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R6023
R6025
R6026
R6027
R7002
1-218-937-11
1-218-990-81
1-218-977-11
1-218-977-11
1-218-949-11
RES-CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
47
0
100K
100K
470
5%
1/16W
5%
5%
5%
1/16W
1/16W
1/16W
R7003
R7051
R7052
1-218-957-11 RES-CHIP
1-208-699-11 METAL CHIP
1-208-695-11 METAL CHIP
2.2K
4.7K
3.3K
5%
0.5%
0.5%
1/16W
1/16W
1/16W
R1001
R1007
R1008
R1009
R1010
1-218-941-81
1-218-941-81
1-218-961-11
1-218-953-11
1-220-803-81
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100
100
4.7K
1K
4.7
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R1011
R1012
R1013
R1014
R1015
1-244-161-81
1-218-953-11
1-218-957-11
1-218-990-81
1-218-990-81
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
SHORT CHIP
2.2
1K
2.2K
0
0
5%
5%
5%
1/16W
1/16W
1/16W
R2001
R2007
R2008
R2009
R2010
1-218-941-81
1-218-941-81
1-218-961-11
1-218-953-11
1-220-803-81
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100
100
4.7K
1K
4.7
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R2011
R2012
R2013
R2014
R2015
1-244-161-81
1-218-953-11
1-218-957-11
1-218-990-81
1-218-990-81
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
SHORT CHIP
2.2
1K
2.2K
0
0
5%
5%
5%
1/16W
1/16W
1/16W
R3001
R3002
R3003
R3004
R3011
1-218-957-11
1-218-990-81
1-218-977-11
1-218-941-81
1-218-977-11
RES-CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
2.2K
0
100K
100
100K
5%
1/16W
5%
5%
5%
1/16W
1/16W
1/16W
R3013
R3014
R3015
R3016
R3017
1-218-979-11
1-218-977-11
1-218-969-11
1-218-945-11
1-218-977-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
150K
100K
22K
220
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3018
R3020
R3021
R3022
R3023
1-218-977-11
1-218-929-11
1-218-981-11
1-218-990-81
1-218-985-11
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
RES-CHIP
100K
10
220K
0
470K
5%
5%
5%
1/16W
1/16W
1/16W
*********************
5%
1/16W
2-655-927-01 TERMINAL (–), BATTERY
R3025
R3026
R3027
R3028
R3029
1-218-961-11
1-218-957-11
1-218-965-11
1-218-945-11
1-218-973-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
4.7K
2.2K
10K
220
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3030
R3031
R3032
R6001
R6002
1-218-977-11
1-218-990-81
1-218-941-81
1-218-985-11
1-218-985-11
RES-CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100K
0
100
470K
470K
5%
1/16W
5%
5%
5%
1/16W
1/16W
1/16W
R6003
R6004
R6005
R6006
R6007
1-218-985-11
1-218-985-11
1-218-977-11
1-218-977-11
1-218-977-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
470K
470K
100K
100K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R6008
R6009
R6010
R6011
R6012
1-218-985-11
1-218-977-11
1-218-985-11
1-218-985-11
1-218-985-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
470K
100K
470K
470K
470K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R6013
1-218-977-11 RES-CHIP
100K
5%
1/16W
36
< COMPOSITION CIRCUIT BLOCK >
RB6001 1-233-973-11 RES, NETWORK (CHIP TYPE) 100K
RB6002 1-233-973-11 RES, NETWORK (CHIP TYPE) 100K
< SWITCH >
S7002
S7003
S7004
1-786-515-21 SWITCH, TACTILE (A-B
/PRIORITY)
1-786-515-21 SWITCH, TACTILE (DIVIDE)
1-786-638-21 SWITCH, TACTILE (ERASE)
< VIBRATOR >
X6001 1-813-165-21 VIBRATOR, CRYSTAL 11.2896MHz
************************************************************
< CAPACITOR >
C5001
C5002
C5003
C5004
C5005
1-125-777-11
1-125-777-11
1-137-934-91
1-125-777-11
1-117-919-11
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
TANTAL. CHIP
0.1uF
0.1uF
47uF
0.1uF
10uF
10%
10%
20%
10%
20%
10V
10V
10V
10V
6.3V
C5006
C5007
C5009
C5010
C5011
1-125-777-11
1-125-837-91
1-125-777-11
1-125-777-11
1-164-858-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
1uF
0.1uF
0.1uF
22PF
10%
10%
10%
10%
5%
10V
6.3V
10V
10V
50V
C5012
C5014
C5016
C5017
C5018
1-164-931-11
1-110-569-11
1-135-993-11
1-137-934-91
1-137-934-91
CERAMIC CHIP
TANTAL. CHIP
TANTAL. CHIP
TANTAL. CHIP
TANTAL. CHIP
100PF
47uF
33uF
47uF
47uF
10%
20%
20%
20%
20%
50V
6.3V
10V
10V
10V
C5020
C5021
C5022
C7001
C7003
1-125-777-11
1-125-777-11
1-131-860-91
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
4.7uF
0.1uF
0.1uF
10%
10%
20%
10%
10%
10V
10V
10V
10V
10V
ICD-SX46/SX56/SX66
MAIN
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
IC7003
IC7004
6-806-071-01 IC MB91233LLGA-G-109E1
6-703-861-01 IC RX-4591CF
IC7005
IC8001
IC8003
6-701-736-01 IC R3130N28EA-TR
6-702-098-01 IC M66291GP-2
6-704-146-01 IC XC62FP3502MR
C7004
C7005
C7006
C7009
C7010
1-125-777-11
1-125-777-11
1-125-777-11
1-164-931-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
100PF
0.1uF
10%
10%
10%
10%
10%
10V
10V
10V
50V
10V
C7011
C7012
C7013
C7014
C7015
1-125-777-11
1-125-777-11
1-125-777-11
1-125-777-11
1-164-937-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.001uF
10%
10%
10%
10%
10%
10V
10V
10V
10V
50V
C7016
C7017
C7018
C7019
C7020
1-137-934-91
1-125-777-11
1-125-777-11
1-164-931-11
1-164-937-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
0.1uF
0.1uF
100PF
0.001uF
20%
10%
10%
10%
10%
10V
10V
10V
50V
50V
C7021
C7022
C7023
C8001
C8002
1-125-777-11
1-125-837-91
1-164-943-81
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
1uF
0.01uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
10V
6.3V
16V
10V
10V
Q5001
Q5002
Q5003
Q5005
Q5006
6-550-747-01
8-729-053-03
8-729-051-50
8-729-927-99
8-729-044-37
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
3LP01S-K-TL-E
XP151A12A2MR
XP152A12C0MR
2SC4617TL-QR
2SK3019TL
C8003
C8004
C8005
C8006
C8007
1-164-856-81
1-164-937-11
1-164-856-81
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
18PF
0.001uF
18PF
0.1uF
0.1uF
5%
10%
5%
10%
10%
50V
50V
50V
10V
10V
Q5007
Q5009
Q5010
Q5011
Q5012
8-729-041-23
6-551-064-01
8-729-044-37
6-550-747-01
8-729-044-37
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
NDS356AP
TPCF8201 (T5RSONY.F)
2SK3019TL
3LP01S-K-TL-E
2SK3019TL
C8009
C8010
1-131-860-91 TANTAL. CHIP
4.7uF
1uF
20%
10%
10V
6.3V
Q5013
Q7001
Q7002
Q7003
Q7004
6-550-861-01
8-729-041-23
6-550-747-01
6-550-747-01
8-729-042-72
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
NTHS2101PT1G
NDS356AP
3LP01S-K-TL-E
3LP01S-K-TL-E
UN9214J-(K8).SO
Q7005
8-729-042-72 TRANSISTOR
UN9214J-(K8).SO
< JACK >
J5001
1-794-615-11 JACK, DC (POLARITY UNIFIED TYPE)
(DC IN 3V !)
< COIL >
< CONNECTOR >
CN7001 1-815-153-11 CONNECTOR (USB) 5P (
)
CN7004 1-817-991-21 CONNECTOR, BOARD TO BOARD 40P
L5001
L5002
1-456-159-11 INDUCTOR
1-456-159-11 INDUCTOR
22uH
22uH
< TRANSISTOR >
< RESISTOR >
< DIODE >
D5002
D5003
D5004
D5005
D5007
8-719-075-93
8-719-081-34
8-719-081-34
8-719-075-93
8-719-056-59
DIODE
DIODE
DIODE
DIODE
DIODE
MA2ZD02001SO
RB160M-30TR
RB160M-30TR
MA2ZD02001SO
MAZS120008SO
D5009
D7004
D8001
D8002
8-719-056-59
8-719-016-74
8-719-069-29
8-719-016-74
DIODE
DIODE
DIODE
DIODE
MAZS120008SO
1SS352-TPH3
RB520S-30TE61
1SS352-TPH3
< FERRITE BEAD >
FB7001 1-500-282-11 INDUCTOR, FERRITE BEAD
FB7002 1-500-282-11 INDUCTOR, FERRITE BEAD
R3024
R5001
R5002
R5003
R5004
1-218-985-11
1-208-935-11
1-208-923-11
1-218-985-11
1-218-990-81
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
SHORT CHIP
470K
100K
33K
470K
0
5%
0.5%
0.5%
5%
1/16W
1/16W
1/16W
1/16W
R5005
R5006
R5007
R5008
R5009
1-218-985-11
1-208-955-11
1-218-985-11
1-208-955-11
1-218-985-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
680K
470K
680K
470K
5%
0.5%
0.5%
0.5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5010
R5011
R5012
R5013
R5014
1-208-939-11
1-218-957-11
1-208-947-11
1-218-953-11
1-218-977-11
METAL CHIP
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
150K
2.2K
330K
1K
100K
0.5%
5%
0.5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5015
R5016
R5017
R5021
R5022
1-218-985-11
1-218-985-11
1-218-989-11
1-218-985-11
1-218-985-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
470K
470K
1M
470K
470K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R5024
R5025
R7001
R7004
1-220-804-11
1-218-989-11
1-218-989-11
1-218-990-81
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
2.2M
1M
1M
0
5%
5%
5%
1/16W
1/16W
1/16W
< IC >
IC5001
IC5002
IC5003
IC5005
IC7001
6-703-864-01
6-705-321-01
6-703-860-01
6-703-865-01
8-759-670-89
IC
IC
IC
IC
IC
R1160N291B-TR-FA
S1F77600M0A000L
XC9502B092AR
XC61CS23XXNR
BU2090FS-E2
IC7002
IC7002
IC7002
6-707-830-01 IC K04SONY95 (SX66)
6-708-162-01 IC K05SONY03 (SX56)
6-708-487-01 IC NAND01GW3B2AN6F (SX46)
37
ICD-SX46/SX56/SX66
MAIN
Ref. No.
SW
Part No.
Description
Remark
R7006
1-208-691-11 METAL CHIP
2.2K
0.5%
1/16W
R7007
R7008
R7009
R7010
R7011
1-208-683-11
1-208-683-11
1-218-989-11
1-218-965-11
1-218-985-11
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
1K
1M
10K
470K
0.5%
0.5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R7012
R7013
R7014
R7015
R7016
1-218-985-11
1-208-911-11
1-208-911-11
1-218-953-11
1-218-981-11
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
470K
10K
10K
1K
220K
5%
0.5%
0.5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R7017
R7019
R7020
R7022
R7023
1-218-990-81
1-218-990-81
1-218-953-11
1-218-953-11
1-218-985-11
SHORT CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
0
1K
1K
470K
5%
5%
5%
1/16W
1/16W
1/16W
R7025
R7027
R7028
R7029
R7030
1-218-985-11
1-218-977-11
1-218-953-11
1-218-977-11
1-218-941-81
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
470K
100K
1K
100K
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R7031
R7032
R7033
R7034
R7037
1-218-977-11
1-218-977-11
1-218-977-11
1-218-977-11
1-218-990-81
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
100K
100K
100K
100K
0
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R7038
R7039
R7040
R7041
R7042
1-218-977-11
1-218-953-11
1-218-985-11
1-218-990-81
1-218-985-11
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
RES-CHIP
100K
1K
470K
0
470K
5%
5%
5%
1/16W
1/16W
1/16W
5%
1/16W
R7043
R7044
R7045
R7046
R7047
1-218-985-11
1-218-953-11
1-218-985-11
1-218-985-11
1-218-953-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
470K
1K
470K
470K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R7048
R7050
R7053
R7054
R8001
1-218-953-11
1-218-953-11
1-218-985-11
1-218-953-11
1-218-985-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
1K
470K
1K
470K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R8002
R8003
R8004
R8005
R8006
1-218-985-11
1-218-977-11
1-218-977-11
1-218-985-11
1-218-989-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
470K
100K
100K
470K
1M
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R8007
R8009
R8010
R8011
R8012
1-218-985-11
1-218-945-11
1-218-977-11
1-218-977-11
1-218-977-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
470K
220
100K
100K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R8013
R8015
R8016
R8020
R8021
1-218-957-11
1-218-933-11
1-218-933-11
1-242-967-81
1-218-961-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
2.2K
22
22
1
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R8022
1-218-949-11 RES-CHIP
470
5%
1/16W
Ref. No.
Part No.
Description
Remark
< SWITCH >
S7001
1-572-922-11 SWITCH, SLIDE (HOLD .)
< TRANSFORMER >
T5001
1-416-405-21 FILTER, CHIP EMI (COMMON MODE)
< THERMISTOR >
TH5001 1-805-762-11 THERMISTOR, POSITIVE
< VIBRATOR >
X7001 1-795-977-21 VIBRATOR, CERAMIC 4.096MHz
X8001 1-813-164-21 VIBRATOR, CRYSTAL 12MHz
************************************************************
A-1149-226-A SW BOARD, COMPLETE (SX66)
A-1157-601-A SW BOARD, COMPLETE (SX46/SX56)
*******************
1-860-643-13 SW FLEXIBLE BOARD
2-655-905-01 BUTTON (5D) (SX46/SX56)
2-655-905-11 BUTTON (5D) (SX66)
< CAPACITOR >
C901
C902
0.0047uF 10%
0.0047uF 10%
16V
16V
< RESISTOR >
R901
R902
R903
R904
R905
1-208-691-11
1-208-695-11
1-208-699-11
1-208-923-11
1-208-715-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
3.3K
4.7K
33K
22K
0.5%
0.5%
0.5%
0.5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R907
R908
R909
1-208-683-11 METAL CHIP
1-208-715-11 METAL CHIP
1-208-923-11 METAL CHIP
1K
22K
33K
0.5%
0.5%
0.5%
1/16W
1/16W
1/16W
< SWITCH >
38
S901
S902
S903
S904
S905
1-771-844-21
1-771-844-21
1-771-844-21
1-771-844-21
1-786-294-61
SWITCH, TACTILE (SMD) (VOL+)
SWITCH, TACTILE (SMD) (VOL–)
SWITCH, TACTILE (SMD) (x STOP)
SWITCH, TACTILE (SMD) (z REC/REC PAUSE)
SWITCH, MULTIPLE FUNCTION
(FOLDER/MENU/./x N/>)
z
S906
1-572-922-11 SWITCH, SLIDE (VOICE UP)
S907
1-572-922-11 SWITCH, SLIDE (DIRECTNL)
S908
1-572-922-11 SWITCH, SLIDE (DPC)
************************************************************
MISCELLANEOUS
**************
LCD
1-802-005-11 DISPLAY PANEL, LIQUID CRYSTAL
MIC2/3 1-479-549-11 MICROPHONE UNIT
SP3001 1-825-993-11 SPEAKER (1.6cm)
************************************************************
ICD-SX46/SX56/SX66
Ver. 1.3
Ref. No.
Part No.
Description
Remark
ACCESSORIES
***********
1-829-882-12
2-585-845-01
2-655-345-12
2-655-345-21
CORD, CONNECTION (USB)
CASE, CARRYING
MANUAL, INSTRUCTION (ENGLISH)
MANUAL, INSTRUCTION (FRENCH)
(CND, AEP, CEW)
2-655-345-31 MANUAL, INSTRUCTION (SPANISH) (AEP, E)
2-655-345-41
2-655-345-51
2-655-345-61
2-655-345-71
2-655-345-81
MANUAL, INSTRUCTION (DUTCH) (AEP)
MANUAL, INSTRUCTION (SWEDISH) (AEP)
MANUAL, INSTRUCTION (PORTUGUESE) (AEP)
MANUAL, INSTRUCTION (GERMAN) (AEP)
MANUAL, INSTRUCTION (ITALIAN) (AEP)
2-655-345-91 MANUAL, INSTRUCTION (RUSSIAN) (AEP)
2-655-348-11 INSTRUCTION (Guide for Voice Recognition)
(ENGLISH) (US, AEP, UK, CEW)
(FRENCH, SPANISH) (CND, AEP, CEW)
(GERMAN, DUTCH) (AEP)
(ITALIAN) (AEP)
2-655-350-11 MANUAL, INSTRUCTION(Digital Voice
Editor 2.40)(ENGLISH) (EXCEPT CH)
2-655-350-21 MANUAL, INSTRUCTION(Digital Voice
Editor 2.40) (TRADITIONAL CHINESE) (E, JE)
2-655-350-31 MANUAL, INSTRUCTION (Digital Voice
Editor 2.40) (SIMPLIFIED CHINESE) (E, JE)
Editor 2.40) (KOREAN) (E, KR, JE)
Editor 2.40) (FRENCH, SPANISH) (CND, AEP, E, CEW)
Editor 2.40) (GERMAN, PORTUGUESE) (AEP)
Editor 2.40) (DUTCH, SWEDISH) (AEP)
Editor 2.40) (ITALIAN, POLISH) (AEP)
Editor 2.40) (RUSSIAN) (AEP)
2-655-354-12 APPLICATION (CD-ROM) (EXCEPT CH)
2-655-354-21 APPLICATION (CD-ROM) (CH)
2-656-636-11 MANUAL (Digital Voice Editor 2.40),
INSTRUCTION (ENGLISH) (CH)
2-656-636-21 MANUAL (Digital Voice Editor 2.40),
INSTRUCTION (SIMPLIFIED CHINESE) (CH)
2-656-638-11 MANUAL, INSTRUCTION
(SIMPLIFIED CHINESE) (E, JE)
(TRADITIONAL CHINESE) (E, JE)
2-656-638-31 MANUAL, INSTRUCTION (KOREAN) (E, JE)
2-656-638-41 MANUAL, INSTRUCTION (PORTUGUESE) (AEP)
(SIMPLIFIED CHINESE) (CH)
2-656-639-21 MANUAL, INSTRUCTION (KOREAN) (KR)
8-954-008-92 RECEIVER, EAR MDR-E808LP/C SET
(EXCEPT CEW)
39
ICD-SX46/SX56/SX66
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
Date
Description of Revision
1.0
2005.11
New
1.1
2006.01
Addition of US model for ICD-SX46
Addition of AEP, UK and E models for ICD-SX46/SX56
1.2
2006.03
Addition of Canadian model for ICD-SX46
1.3
2006.06
Addition of France model for ICD-SX46

ICD-SX46/SX56/SX66

Transcription

Similar documents

CC46 - Antidote