- Dynamic Controls

SOLUTIONS
PRODUCT CATALOGUE FOR POWERED WHEELCHAIRS AND SCOOTERS • 2014
Catalogue part no. GBR59617 • Issue 4
Contents
Introduction .............................................................................................02
Product Family Selection Guide.....................................................03
LiNX Wheelchair Control Solution .................................................05
iPortal Wheelchair Interface ...........................................................11
DX2 & DX Wheelchair Control Systems.......................................15
Shark Wheelchair Control System..................................................47
R-Series Scooter Controller................................................................53
Rhino2 Scooter Controller..................................................................59
Programming for DX/DX2, Shark, R-Series & Rhino2........61
Accessories..............................................................................................65
1
INTRODUCTION
Dynamic Controls is committed to enhancing
people’s lives. Our philosophy is built on
combining an intimate understanding of the
needs of mobility product users with our research
and design skills. This has enabled us to be the
world’s premier supplier of electronic control
systems for power wheelchairs and scooters for
over 30 years.
Our products range from cost effective integral
controllers to a world leading modular control
system that can be customised to suit a wide
range of user needs. In addition we have a range
of scooter controllers suitable for small, lightweight
mini shoppers to rugged outdoor scooters. All our
products are renowned for reliability.
Dynamic Controls is unique in that we specialize
in the medical mobility market. This means we are
able to offer our customers an unrivalled level of
experience and support.
Dynamic Controls is a global organization with
corporate headquarters in New Zealand and
regional offices in the United Kingdom, North
America and Asia. To find out more please visit
www.dynamiccontrols.com
Dynamic Controls maintains a rigorous quality management system and is independently audited to the
exacting requirements of ISO13485.
2
PRODUCT FAMILY SELECTION GUIDE
Wheelchair Controllers
LiNX
LiNX is a new technology platform driven by market insights.
It is a modular system designed to be a single, simple and
expandable system for all segments of the wheelchair market:
from simple sit and drive through to complex rehabilitation. It
includes wireless connectivity for new programming, diagnostics
and data functions plus patented new motor control
technology.
SHARK
Reliable solution for most standard power chair applications.
Suitable for mid range power requirements with options to
support actuators, lighting and attendant control.
DX2 / DX
High Performance system designed for higher power rehab
chairs. Based on a modular design with the flexibility to
integrate a wide range of input and control devices.
iPortal
iPORTAL
A range of Bluetooth modules that connects a wheelchair
controls to an iPhone/iPod/iPad and or PC/Mac/tablet
computer, giving the user full control of these devices from the
joystick or speciality input controls.
Scooter Controllers
R-SERIES
Cost effective scooter controllers available in 50A and
90A variants.
RHINO2
Range of high quality, reliable scooter
controllers ideal for higher power applications.
3
4
LiNX
LE
WHEELCHAIR CONTROL SOLUTION
5
THE LiNX LE WHEELCHAIR CONTROL SYSTEM
The LiNX LE control system is ideally suited to light-weight indoor power wheelchairs. It is the preferred
solution where simplicity, reliability and superb drive performance are most important. The system is
based on Dynamic Controls’ new, state of the art, LiNX controller architecture.
• Ideal for light weight, indoor wheelchairs
• Easy to use
• Simple
• Reliable
• Part of the next generation controller family
• Advanced differential drive control
• Suitable for all wheelchair configurations:
FWD, CWD and RWD
• Unique, ergonomically designed remote
modules
• Global standards compliant
• Off-board charger connection via an
industry-standard XLR connector
• Intended for use with Class A and Class B
wheelchairs as defined in ISO7176 Part 5
and EN12184
LiNX
LE Selection
Guide
6
System Part Number Description
Modules
DLX050-40-10
LE system with REM50, 40A PM
and 1m cable
DLX-PM40-A
DLX-REM050-A GLM-BUS100-A
DLX050-40-15
LE system with REM50, 40A PM
and 1.5m cable
DLX-PM40-A
DLX-REM050-A GLM-BUS150-A
DLX050-40-10-09
LE system with REM50, 40A PM,
1m cable and .9m ext cable
DLX-PM40-A
DLX-REM050-A GLM-BUS100-A GLM-EXT090-A
DLX050-40-10-06
LE system with REM50, 40A PM,
1m cable and .64m ext cable
DLX-PM40-A
DLX-REM050-A GLM-BUS100-A GLM-EXT064-A
LiNX LE REMOTE
The compact LiNX LE remote features leading edge
ergonomic styling with controls orientated toward the
user making it safer and simpler to use without being
obscured by the joy stick. The low deflection force joy
stick and associated hand rest area make it a stable
platform for stress free driving.
• Simple and intuitive controls
• Comfortable and natural to use
• Unparalleled fine control at low speed
Part Number
DLX-REM050-A
• High quality finish
Technical Specifications
Material
Plastic
Size 163 x 73 x 107 mm
Protection rating
IPX4
Weight
305 grams
Operating Temp
-25 to 50°C
Connectors
1 LiNX BUS Socket
Storage Temp
-40 to 65°C
1 XLR Charger Socket
LiNX LE POWER MODULE
The power module is a balance of reduced size and
optimum performance. It incorporates new patented
technology that ensures best in class drive performance.
• Programmable current and boost current up to 40A
• Superior user ride experience from advanced
technology
• Uses the same battery and motor connectors as Shark
and DX2
• Power Module has the same mount pitch as Shark
Part Number
DLX-PM40-A
Technical Specifications
Material
Die-cast aluminium, with plastic
shroud and steel base plate
Protection rating
IPX4
Operating Temp
-25 to 50°C
Storage Temp
-40 to 65°C
LiNX LE Cable
Size 168 x 88 x 43 mm
Weight
730 grams
Connectors
1 LiNX BUS Socket
1 Battery Socket
2 Motor Sockets
Flexible and robust cable options designed
to meet all chair configurations.
Part numbers
Description
GLM-BUS100-A
1.0m Bus cable
GLM-BUS150-A
1.5m Bus cable
GLM-EXT090-A
900mm extension cable
GLM-EXT064-A
640mm extension cable
Connectors
LiNX LE uses the same motor and
battery connectors as Shark and DX2.
Refer to pages 41, 42 and 52.
7
LiNX ACCESS TOOLS
The LiNX system brings a revolutionary approach to programming, diagnosing and updating of wheelchair
systems through its wireless LiNX Access tools. Without a wired connection between the programmer and
the wheelchair you have a lot more freedom during the setup and tuning process. An important new
feature is the ability to wirelessly upgrade the system firmware of all LiNX modules.
The LiNX Access Keys provide the appropriate level of access for Manufacturers and Distributors and
provide the wireless communication between either a PC, or an Apple iOS device, and the wheelchair
system. You can choose which device (iOS or PC) best suits your business or application need and
then enjoy the inherent benefits that high end electronics products bring, such as file storage and
management.
To make it easy to transition to LiNX, the product set has also been made backwards compatible with the
DX-HHP.
Tool Set
Key Features
• LiNX Access PC
• Live Update: Instant wireless updating of parameters
on the move
• LiNX Access iOS (For Apple devices)
• LiNX Access Keys (Manufacturer &
Distributor access levels)
• Firmware upgrade: wirelessly upgrade an entire system
• Easy to use: advanced user interface built around
common tasks
• Simple: logical presentation of parameters and profiles
• Save time: faster programming
• Connected: Email or receive files within the application
• Keep up to date: PC & iOS tools remain updated
(when connected to internet)
8
LiNX Access PC
LiNX Access iOS
Compatible with:
Compatible with:
• iPhone 3GS
Software
• iPhone 4
• Windows XP, service pack 2 or later
(preferably SP3)
• iPhone 4S
• Windows Vista, all versions
• iPhone 5
• Windows 7, all versions
• iPod Touch Gen 3
• Windows 8
• iPod Touch Gen 4
Hardware
Check www.dynamiccontrols.com for the list for
tested and verified versions of iOS.
• A Bluetooth radio, Bluetooth version 2.0 or
later, which is supported by the drivers.
Upgrading to an unverified iOS version is not
recommended.
Download from www.dynamiccontrols.com/downloads
Download through the App Store on your
device or from www.apple.com/itunes
LiNX ACCESS KEYS
The Access Key plugs into the XLR charger
port of the LiNX remote and provides the
Bluetooth wireless communications to the PC
and iOS programming tools. These keys provide
dedicated access levels for Manufacturers and
their Distributors to ensure that the appropriate
level of configuration is available.
LiNX Access Key Part numbers
DLX-HKEY01-A(Distributor)
DLX-HKEY02-A(Manufacturer)
Technical Specifications
Material
Plastic
Size 73 x 60 x 24 mm
Operating Temp
-25 to 50°C
Weight
42 grams
Storage Temp
-40 to 65°C
9
iPortal
TM
MOUSE MOVER & iPHONE/iPOD/iPAD
WHEELCHAIR INTERFACE
11
DJ-BTINT iPortal™ Bluetooth Module
DJ-GNKS-IPH/DJ-GNKL-IPH
Gooseneck mounts
DJ-BTINT
A Bluetooth module that allows power wheelchair
users to operate an Apple iPod touch, iPhone and
iPad and/or operate a computer mouse directly from
their joystick or other speciality input device with full
proportional control.
Flexible gooseneck mounts
for mounting iPhone and
iPod touch to a power wheel
chair in combination with
iPortal™.
Key Features
• Operates with Shark*, DX and DX2 remotes
• Control iPod touch, iPhone and iPad using the
remote joystick
• Control a computer mouse using the remote
joystick
• Works with PC, Mac, Linux & tablets that work with
a Bluetooth mouse
• Automatic pairing
• Non directional and no line of sight required
• Small, lightweight and multifunctional
• Plug and play, no reprogramming needed
• Upgrades to functionality can be purchased on
the App store
• Charges Apple devices and other USB devices
Key Features
• Fits iPhone 3 and 4
• Fits iPod 2nd & 3rd
generation
• Includes integrated Apple
USB cable for charging
from the iPortal™
• Convenient M10 bolt
mounting
• 2 lengths available
* Requires a switch or buddy button wired to the
power module.
Part numbers
DJ-GNKS-IPH Gooseneck short – 330mm
DJ-GNKL-IPH Gooseneck long – 490mm
Part numbers
DJ-GNKL-IPH
DJ-BTINT
Dashboard App – high end display and
diagnostics
DJ-BTINT-ACC
Full control of iPod touch, iPhone and
iPad
DJ-BTINT-HID
Computer mouse control
DJ-BTINT-HID-ACC Computer mouse control + full control of
iOS devices
Technical Specifications
Material
Aluminium
& Plastic Protection IPX4
rating
12
Operating -25 to 50°C
Temp
Storage -25 to 70°C
Temp
Connectors
1 x USB power only
Size
1 x USB power only
(Apple only)
115 x 79 x 32mm
Weight 235g
1 x Shark bus
1 x DX2/DX bus
Material
Plastic with copper rod core
Mounts for iPad
Mounts for iPhone and iPod
GME0035
Holder for Apple iPad, iPad
2 and the new iPad
GME0036
Lockable ram holder for
Apple iPad, iPad 2 and
the new iPad. Has 4 digit
combination lock
GME0029
Mount with U – bolt, for
Apple iPhone 4 & 4s
GME0030
Mount with U – bolt,
for Apple iPhone 3G
GME0037
U-bolt mount base
GME0038
Yoke mount w/
plastic arm/base,
easily removable
clamp mount
GME0031
Holder for Apple
iPhone 4 & 4s
GME0032
Holder for Apple iPod
touch 4th Generation
GME0040
Mount for
iPhone 5
GME0033
U-bolt mount
GME0039
18” flexible gooseneck, easily
removable clamp mount
Notes
Select a cradle that suits how you want to
use your iPad.
Select a mounting arm that will best suit
how you wish to mount your iPad on your
powerchair.
iPad is not included.
Cradles will not accept iPads with covers.
Non standard delivery times may apply
GME0034
18” flexible seat
clamp mount
Notes
Select a cradle/mount to suit your iPhone.
Or
Select a cradle that suits your particular iPhone or iPod.
Ensure you select the right cradle.
Select a mounting arm that will best suit how you wish to
mount your iPhone or iPod on your powerchair.
iPhone or iPod is not included.
Cradles will not accept iPhone or iPod with covers.
Non standard delivery times may apply
13
DX2 & DX
TM
WHEELCHAIR CONTROL
SOLUTION FOR REHAB
APPLICATIONS
Whats New!
• Improved User Interface
(REM550)
• Increased power for actuator
control and actuator auto
detect
• New micro extremity speciality
control joystick.
15
DYNAMIC CONTROLS DX2/DX COMPONENTS
Master Remotes
DX2-REM550/551
Advanced Joystick Remotes
DX2-REM420
Joystick Remote
DX2-REM421
Joystick Remote
DX-REMG90
Joystick Remote
Secondary Remotes
DX-ACU1
Attendant Dual Control
DX-RJM
Remote Joystick
DX-RJM-HD
Heavy Duty Joystick
Actuator Modules
Power Modules
DX2-PMA70/70L/90/90L
DX2 Power Modules
70 or 90A (120A boost)
With or without lighting
DX2-ACT2/ACT4
DX2 Actuator Modules
2 or 4 channel
DX-PMB2-S
Single channel Power Module
160A
16
DX-SLM
Servo Lighting Module
DX-CLAMB
Combined Lighting Actuator Module
DX-REM34B
Joystick Remote
DX-REMG91/G91S
Display Remotes
DX-REM41D
Tray Remote
DX-ACC4B
Switch Input
DX-ACU3B
Attendant Master Remote
DSL-105STA
Head array
DSL-105M
Mini head
array
Other DSL Head
array models
available. See
pages 36 and 37.
DX-SNP
Sip & Puff Input
Environmental
Control
TM
DJ-GNKL-IPH
Gooseneck Mount
DX-ARC5
Actuator Remote Control
DX-ARC-SWB
Actuator Remote Control
iPortal
DX-ECU
Environmental Control Unit
DJ-BTINT
iPortalTM2 Bluetooth Module
DX-LM-Z
Lighting Module
17
TM
Product Tree
THE DX2 SYSTEM
DX2 is a modular power wheelchair control solution that expands the proven DX system through the
addition of powerful new components. These allow the design of a rehab power chair that will meet the
requirements of any user ranging from drive only control to full environmental control.
The DX2 system is designed to maximise comfort and user control, is easy to set up and maintain and is
highly reliable.
Key Features
• Large full-colour LCD display with intuitive graphical user interface
• Smooth fine control of seating
• Compact powerful power modules with optional built-in lighting
• Reduced set up time through system programming backup
• Backward compatible with DX system
Power Module
P
Master Remote
Battery
Charger
Hand Held
Programmer
Optional DX BUS
P
(Optional)
Actuator Module
Optional DX BUS
DX BUS
Wizard
PC-based
Programmer
(Optional)
Secondary Remote
Master Remotes
Other
Secondary Remotes
DX2-REM550/1
DX-ACC3
DX-ACU1
DX2-REM420/1
DX-SKT-X3
DX-RJM
DX-REMG90
DX-RJM-HD
DX-REMG91
DX2- ACU- 1A
DX-REMG91S
Power Modules/Lighting
DX2-RJM-1A
DX-REM34B
DX2-PMA70
DX-ACC4B
DX-REM41D
DX2-PMA70L
DX-SNP
DX-ACU3B
DX2-PMA90
ASL-130
DX2-PMA90L
Actuator Modules
DX-PMB2-S
DX2-ACT2
DX-SLM
DX-ECU
DX2-ACT4
DX-ARC5
Programming
DX-ARCSWB
WIZARD
DX-CLAMB
DX-HHP
DX-LM-Z
DX-ARC5
DXARCSWB
18
Environmental Controls
DJ-BTINT
DX2/DX SYSTEM CONFIGURATIONS
A key feature of the DX2 system is backwards compatibility with the DX system. This means that DX2 and
DX modules may be used within the same system.
Master Remote
Power Module
Any DX/DX2 Module
or
or
or
DX
DX2
DX
DX2
DX
DX2
The modules required for some typical applications are listed below.
Application
Joystick - Armrest mounted
DX2-REM550
DX-REMG90A
DX-REM34B
DX2-REM42x
Joystick - Mid or tray-mounted
DX-REMG91 & DX-RJM or DX2-RJM
DX-REM41D
DX-REM35B
Joystick for heavy duty use
DX-RJM-HD
Chin Joystick
DX-RJM or DX2-RJM
DX-REM32B
Tray Switches
DX-REMG91 & DX-ACC4B
Head Controls
ACC4B & DSL105X
Single Switch Control
DX-REMG91S
Sip N Puff Breath Control
DX-REMG91 & DX-SNP
Light Touch 1 option
DX-REMG91 & ASL-130
Attendant Control
DX-ACU or DX2-ACU
DX-ACU3B
Environmental Control or PC Mouse Control
DJ-BTINT & DX-ECU
19
DX2/DX MASTER REMOTE SELECTION GUIDE
Check the following table for a quick reference to the options on each Master Remote.
Power
Module
Motor
Motor
Battery
20
Seat controls
P
5
P
P
DX2-REM551
P
Col
LCD
5
P
5
P
P
DX2-REM420
P
LED
8
P
5
P
P
DX2-REM421
P
LED
4
P
5
P
P
DX-REMG90
P
LED
7seg
6
P
5
P
P
DX-REMG90A
P
LED
7seg
6
P
5
P
DX-REMG90T
P
LED
7seg
6
P
5
P
DX-REMG91
LED
7seg
4
P
P
DX-REMG91S
LED
7seg
4
P
P
Computer
mouse control
Lock
7
Environmental
controls
Maximum no.
drive modes
Col
LCD
Lighting
controls
Battery gauge
P
Internal switch
interface
Display
DX2-REM550
No. buttons
Joystick
Master
Remote
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
Lighting
Menu
P
P
5
P
P
P
P
P
5
P
P
P
P
P
DX-REM34B
P
LED
7seg
12
P
5
P
P
P
P
DX-REM41D
P
LED
7seg
12
P
5
P
P
P
P
DX-ACU3B
P
LED
7seg
3
P
5
P
P
DX2 MASTER REMOTES
DX2-REM550/551 Advanced Joystick Remote
The DX2 Master Remotes are stylish high-end
joystick remotes with a large, clear, full colour LCD
screen. They provide easy control and a high level
of functionality to a wide variety of users.
Key Features
• Large, clear colour LCD screen with icon-based
screen controls
• New and Improved User Interface
• Light sensor to select indoor and outdoor
display mode
• Low-force joystick with proportional or fourquadrant control
• Direct access to computer mouse and
environmental control modules
• Display adapts for right or left-hand mounting
• Battery gauge, real time clock and key pad
controlled lock
• Programmable function keys to give direct
access to chair functions
• Three jack sockets for multi-purpose external
button control
Part numbers
Master Remote
DX2-REM550
DX2-REM550
Master Remote with colour LCD
and 7 buttons
DX2-REM551
Master Remote with colour LCD
and 5 buttons
also required – DX BUS cable
External Buttons (if required for external jack sockets)
Please refer to DX Switches section for details of
external buttons
Technical Specifications
Material
Plastic
Size 211 x 88 x 153 mm
Protection Rating
IPX4
Weight
1100 grams
Operating Temp
-25°C to 50°C
DX Connectors
2 DX BUS Connectors
Storage Temp
-40°C to 70°C
21
DX2-REM420/1
Compact LED Remotes for Light Rehab
applications
For Light Rehab applications with drive and
multiple seating actuators the DX2-REM420 / 421
offer easy-to-use, compact LED master remotes
with smooth, low force joystick control.
DX2-REM420
Key Features
• Compact, LED-based Remotes for Light Rehab
use
• Smooth, low-force joystick
• 5 Drive profiles for optimum driving control in all
situations
• Controls up to 4 seating actuators
• Lighting control (DX2-REM420)
• Battery gauge
• Keypad-controlled Lock and Sleep mode
• Service indication and System Backup Mirror
• Shark-compatible mounting
Part numbers
Master Remote
DX2-REM420
Master Remote with LED Display
and Lighting controls
DX2-REM421
Master Remote with LED Display Also required – DX BUS cable
DX2-REM421
Technical Specifications
22
Material
Plastic
Size 177mm x 76mm x 136mm
Protection Rating
IPX4
Weight
650 grams
Operating Temp
-25°C to 50°C
DX Connectors
1 DX BUS Connectors
Storage Temp
-40°C to 70°C
DX MASTER REMOTES
The master remote is the “brains” of the DX system and every DX power chair must have one. Every
master remote has an On/Off switch, a programming socket and a DX status indicator. They may also
be used to control seat positioning, lighting, and environment controls.
DX-REMG90
High-end joystick remote easily operated by a wide
variety of users.
•
•
•
•
•
5 different drive profiles
7 segment LED display and battery gauge
Proportional, 4-quadrant or 3-quadrant control
Access to actuator and environmental controls
Supports latched actuator and simultaneous
actuator operation
• Optional jack sockets or toggle switches for on/off
and mode control
Power
Module
Motor
Part numbers
Motor
Battery
DX-REMG90A
Master
Remote
DX-REMG90
Master Remote
DX-REMG90A
Master Remote with jack sockets
DX-REMG90T
Master Remote with toggle switches
Technical Specifications
Material
Die-cast aluminium
Size 143 x 71 x 169 mm
Protection rating
IPX4
Weight
620 grams
Operating Temp
-25°C to 50°C
DX Connectors
2 DX BUS Connectors
Storage Temp
-40°C to 65°C
DX-REMG91 Display/DX-REMG91S Scanner Display
High-end display remote ideal for specialty
control inputs.
Power
Module
Motor
Motor
REMG91
Battery
Secondary
Remote
Power
Module
DX-REMG91/G91S
Motor
Motor
REMG91S
Battery
Menu
Switch
(Optional)
Scanning
Switch
• 5 different easily selectable drive profiles
• 7 segment LED display and battery gauge
• Support for proportional joysticks or switched
inputs with 3 or 4 quadrant control
• Access to actuator and environmental controls
• Latched actuator operation
• Three jack sockets or toggle switches for on/off
and mode control
• Single switch control through scanning mode (G91S)
Part numbers
DX-REMG91
Display Master Remote DX-REMG91S
Display Master Remote with scanner
DX-GNK-KIT2 Gooseneck Mounting Kit for DX-REMG91
and DX-REMG91S
Technical Specifications
Material
Plastic
Size 125 x 85 x 32 mm
Protection rating
IPX4
Weight
275 grams
Operating Temp
-25 to 50°C
DX Connectors
1 DX BUS Connector
Storage Temp
-40 to 65°C
23
DX-REM34B Master Remote
A simple joystick remote that can be easily
operated by a wide variety of users.
• 5 different drive profiles
• 12 button keypad with icon based buttons
• Dedicated buttons for actuator selection and
lighting (requires relevant DX modules)
• 7 segment LED display
• Horn, battery gauge and magnetic key lock
Part numbers
DX-REM34B
Master Remote
also required – DX BUS cable
DX-REM34B
Technical Specifications
Material
Plastic
Size
85 x 185 x 150 mm
Protection rating
IP54
Weight 590 grams
Operating Temp
-25 to 50°C
DX Connectors
2 DX BUS Connectors
Storage Temp
-25 to 70°C
DX-REM41D Master Remote
Joystick controlled remote suitable for tray mounting.
• 5 different drive profiles
• 12 button keypad with icon based buttons
• Dedicated buttons for actuator selection
and lighting (requires relevant DX modules)
• 7 segment LED display
• Horn, battery gauge and magnetic key lock
Part numbers
DX-REM41D
Tray Master Remote also required – DX BUS cable
DX-REM41D
Technical Specifications
24
Material
Black powder-coated aluminium
Size
157 x 82 x 120 mm
Operating Temp
-25 to 50°C
Weight 575 grams
Storage Temp
-25 to 70°C
DX Connectors
1 DX BUS Connector
SECONDARY REMOTES
Power
Module
In addition to a Master Remote any DX system
can also have a Secondary Remote installed. This
enables the user to have a wider choice of input or
specialised rehab controls.
Motor
Motor
Battery
Master
Remote
Secondary
Remote
DX-RJM Remote Joystick Module
Standard proportional joystick for mounting in a
range of positions, e.g. chin control, mid line.
DX-RJM
Part numbers
DX-RJM
Remote Joystick Module
Technical Specifications
Material
Black powder-coated aluminium
Size
48 x 48 x 135 mm
Operating Temp
-25 to 50°C
Weight
375 grams
Storage Temp
-25 to 70°C
DX Connector
1 DX BUS plug on a 1.7m cable
DX-ACU3B Master Attendant Remote
A joystick remote that can be operated by an attendant or carer.
•
•
•
•
•
5 different drive profiles
7 segment LED display
Icon-based buttons, battery gauge and magnetic key lock
Push bar or hand grip mounting
On/Off button, battery gauge, and charger socket easily
reached by the attendant
Part numbers
DX-ACU3B
Master Attendant Control
also required – DX BUS cable
DX-ACU3B
Technical Specifications
Material
Black powder-coated aluminium
Size
100 x 130 x 115 mm (including joystick)
Operating Temp
-25 to 50°C
Weight
512 grams
Storage Temp
-25 to 70°C
DX Connectors
2 DX BUS Sockets
25
DX2 CONNECTORS
DX-ACU1 Attendant Dual Control
Joystick remote that enables an attendant to drive
the chair instead of the user.
The attendant dual control unit may be used
in addition to a secondary remote and master
remote all on the same system.
Power
Module
Motor
Motor
• Switchable control between Attendant and User
• Independent speed control
Battery
Master
Remote
DX-ACU1
Dual Control
Secondary
Remote
Part numbers
DX-ACU1
Attendant Dual Control
also required – DX BUS cable
Technical Specifications
26
Material
Black powder-coated aluminium
Size
90 x 62 x 120 mm
Operating Temp
-25 to 50°C
Weight
348 grams
Storage Temp
-25 to 70°C
DX Connectors
1 DX BUS Socket
DX2 POWER MODULES
DX2-PMA70/70L/90/90L
The DX2 power modules are the workhorses of
the DX2 system and provide fast, precise control
of high power drive motors. They are a robust
solution for mid, rear and front wheel drive
configurations.
• 70A or 90A with optional built in lighting
• Programmable current boost
• Built in 3 channel lighting for indicators, hazard
lights, driving lights
• Programmable Drive Control Input (DCI)
• System programming backup
• Service scheduler indicator
• Comprehensive fault protection
DX2-PMA70L
Part numbers
Power Modules
DX2-PMA70
70A power module
DX2-PMA70L
70A power module with lighting
DX2-PMA90
90A power module
DX2-PMA90L
90A power module with lighting
Connector Kits
DX2LOOM-PM1
DX2 Battery & Motor Connector Kit for
DX2-PMA70, DX2-PMA90
or
DX2LOOM-PM2
DX2 Battery & Motor Connector Kit for
DX2-PMA70L, DX2-PMA90L
Motor Connectors
GCN60326
DX2/DX Motor Housing – left motor only
GCN60327
DX2/DX Motor Housing – right motor only
or
GCN60325
DX2/DX Motor Housing – left or right
motor (unkeyed)
GCN60323
Connector Key to configure GCN60320
for left or right use
GCN65129
Boot for battery/ motor connectors
Technical Specifications
Material
Black painted aluminium alloy
Size 180 x 106 x 43 mm
Protection rating
IPX4
Weight
1040 grams
Operating Temp
-25°C to 50°C
DX Connectors
2 DX BUS Connectors
Storage Temp
-40°C to 65°C
27
DX2 GYRO
The DX2 Gyro stabilization dramatically improves the driving stability of wheelchair systems, especially Front
Wheel Drive, as the Gyro accurately tracks the intended direction of the wheelchair from the user input
and corrects any course deviation from this path. Gyro is best offered as a standard feature of wheelchair
designs ex-factory, and it is also possible to offer it as a point of sale upgrade. DX2 Gyro offers commercially
and clinically recognizable benefits to create additional revenue and margin, as well as enhancing the
perceived quality or your drive and brand in the market.
Adding gyro to your wheelchair systems can:
• Improve the perceived quality of your wheelchair driving
experience
• Significantly reduce the effort required to operate a
wheelchair, which can be important for switch access
and low strength drivers
• Improve the driving safety of wheelchair systems at all
speeds, especially on soft, uneven or slippery surfaces
• Reduce the point to point driving time by improving
driving accuracy and speeds over uneven surfaces and
terrain
The DX2 Gyro system consists of a special power controller
(DX2-PMA90LG) in combination with a digital gyroscopic
module (DX2-GYRO). A Y-Cable may be required in some
setups to split out the DX-BUS from the power controller
(GCB65231).
DX2 Gyro is not available for supply into North America and Canada.
Part numbers
DX2-PMA90LG 90A power module with lighting and gyro input
DX2-GYRO
Gyroscopic input module
Technical Specifications
28
Material
Black painted aluminium alloy
Size 180 x 106 x 43 mm
Protection rating
IPX4
Weight
1040 grams
Operating Temp
-25°C to 50°C
DX Connectors
1 x DX Bus, 1 x Gyro Input
Storage Temp
-40°C to 65°C
DX POWER MODULES
The DX power modules provide excellent response and driving control in all terrain and are available to
suit all mid, rear and front wheel drive configurations.
DX-PMB2-S
• 160A single channel
• Dynamic Controls load compensation algorithm
• Fully programmable to suit all DC motor
power chairs
• Advanced safety and protection features
• Compact, rugged enclosure sealed against dust
and water
• 2 DX BUS connectors for easy system expansion
• Visible “flash code” diagnostics
DX-PMB2-S
Part numbers
DX-PMB2-S
DX Servo Power Module (160A Single Channel)
also required – DXLOOM-PM Connector Kit
Connector Kits
DXLOOM-PM
DX Connector Kit
Technical Specifications
Compatible motors
24 volt DC, Permanent magnet
Storage Temp
-25 to 70°C
Compatible park brakes
12 or 24 volt DC
Size
185 x 125 x 45 mm
Material
Aluminium
Weight
1.4 kilograms
Protection rating
IP54
DX Connectors
2 DX BUS Sockets
Operating Temp
-25 to 50°C
DX-SLM Servo Lighting Module
Servo steering module for use on wheelchairs that have
a separate motor for servo control of steering castors.
Power
Module
(1 or 2 channel)
Optional
Motor
Motor
Master
Remote
Battery
• Control of steering servo with potentiometer
steering feedback
• Provision of lighting outputs
• Range of programming options to give optimum
performance on any servo steered wheelchair
Part numbers
DX-SLM
DX-SLM
DX-SLM
Lighting System
Servo Lighting Module
also required – DX BUS cable, DXLOOM-SLM, DXLOOM-PM Connector Kit, DX-PMB2 or DX-PMB2-S
Servo Steering Motor
Technical Specifications
Compatible motor
24 Volt DC, Permanent magnet
Operating Temp
-25 to 50°C
Servo motor current
30A (peak),
5A (continuous)
Storage Temp
-25 to 70°C
Size
210 x 123 x 38 mm
Material
Black powder coated aluminium
Weight
530 grams
Protection rating
IP54
DX Connectors
2 DX BUS Sockets
29
DX2 & DX ACTUATOR MODULES
DX2-ACT2/4
The DX2 actuator modules are simple to set up
yet are highly configurable. Proportional joystick
controlled actuators give smooth, fine control of
seating for improved comfort. The use of multiple
actuator modules allows control of up to 12
actuators with minimal wiring.
• Proportional, switched, latched and
bi-directional operation
• Soft start and stop of actuators to increase user
comfort
• Simultaneous control of multiple actuators
• Independent extend and retract drive current
limits for each actuator
• Individual actuator connections
• Status LEDs for each channel
• No direct battery connections
• Actuator Control Input (ACI) allows external
switches to control actuators and drive speed
• More Power, auto detect, latched ACI function
DX2-ACT2
Part numbers
DX2-ACT4
Actuator Modules
DX2-ACT2
2-channel actuator module
DX2-ACT4
4-channel actuator module
Connector Kits
DX2LOOM-ACT
Connector Kit for DX-ACT2/ACT4
Power
Module
Motor
Motor
Master
Remote
Battery
DX2-ACT4
Up to 4
Actuators
DX2-ACT2
Up to 2
Actuators
Technical Specifications
30
Material
Plastic
Size 114 x 72 x 25 mm
Protection rating
IPX4
Weight
300 grams
Operating Temp
-25°C to 50°C
DX Connectors
2 DX BUS Connectors
Storage Temp
-40°C to 65°C
DX-CLAMB Combined Lighting and Actuator Module
Single module providing both lighting and seat
actuator functions from a single module.
• Actuator control of up to five separate seat
actuators
• Independent current level trips for each
actuator
• 3 channel lighting support for indicators, hazard
lights, driving lights
• No direct battery connections required, all
power sourced via the DX BUS
• External switch inputs can be programmed to
slow or stop chair driving if activated
DX-CLAMB
Part numbers
Power
Module
Motor
DX-CLAMB
Combined Lighting and Actuator Module
also required – DX BUS cable,
DXLOOM-AUX Connector Kit
Motor
Master
Remote
Battery
DX-CLAMB
Lighting System
Up to 5 Actuators
Technical Specifications
Material
Grey aluminium
Protection rating
IP54
Continuous lighting current
1A (each indicator)
2A (driving light)
Operating Temp
-25 to 50°C
Size
85 x 125 x 30 mm
Storage Temp
-25 to 70°C
Weight
410 grams
3 – 12A (programmable)
DX Connectors
2 DX BUS Sockets
Actuator Current Limit
31
SPECIALTY MODULES
DX-ACC4B Switch Interface
Input module for up to 5 switches.
• 9 pin D-type connector
• Ideal for use with 3-quadrant and 4-quadrant
switched head controls
• Simple driving interface with up to 8 driving
directions
• Provides power to active switch controls
Power
Module
Motor
DX-ACC4B
Motor
Battery
Master
Remote
Four Switch
Interface
Part numbers
DX-ACC4B
Switch Interface
also required – DX BUS cable, switches
Various Switch Options
Technical Specifications
Material
Plastic
Size
90 x 55 x 25 mm
Weight
120 grams
DX Connector
1 DX BUS Socket
DX-SNP Sip and Puff Interface
Sip and Puff control that can be fine tuned to suit
any user or application.
Power
Module
DX-SNP
Motor
Motor
• Fully programmable sip and puff pressures
• 7 standard drive programs
• Latched driving (step or progressive step)
with optimised safety through programmable
emergency stop and latched time options
• Easy custom programming using DX Hand Held
Programmer
• Optimum safety through programmable
Emergency Stop and Latch Time options
• Mode Control feature
Part numbers
Battery
Master
Remote
DX-SNP
Hose
Optional
Emergency
Stop Switch
DX-SNP Sip and Puff Module
also required – DX BUS cable
GSM9977
Sip and Puff Mounting Kit
GSM9942
SNP Filter
SW932662
Set of 10 straws
SWTA5100
SNP breath operated mode switch
Technical Specifications
32
Material
Grey aluminium
Weight
320 grams
Hose size
3.5 mm (1/8”) ID
DX Connector
1 DX BUS Socket
Size
125 x 85 x 30 mm
DX-ARC5 Actuator Remote Control
Separate hand-held remote control for actuators.
•
•
•
•
Power
Module
DX-ARC5
Simple operation
Controls up to 5 actuators
Can be used with DX or DX2 actuator modules
Programmable options to allow seat position to
be adjusted while driving
Part numbers
Motor
DX-ARC5
Motor
Master
Remote
Battery
Actuator Remote Control Module
Please note an actuator module is also required.
DX-CLAMB
DX-ARC5
Actuators
Technical Specifications
Material
Plastic
Size
61 x 135 x 24.5 mm
Protection rating
IPX4
Weight
150 grams
Operating Temp
-25 to 50°C
DX Connector
1 DX BUS plug on a 2m cable
Storage Temp
-25 to 70°C
DX-ARC-SWB Actuator Remote Control Switchbox
Control of up to 5 seat positioning actuators using
switches connected to a 15 pin D-type connector.
Power
Module
Motor
Motor
Master
Remote
Battery
DX-ARC-SWB
• Alternative for users who have difficulty using
actuator controls
• Remote control for actuators using a choice of
external switches (customer supplied)
• Simple operation
• Can be used with DX or DX2 actuator modules
• Switched 24V, 1A auxiliary power supply output
Please note that this unit cannot be used at the same time
as a DX-ARC5.
DX-CLAMB
Part numbers
Actuators
DX-ARC-SWB
DX-ARC-SWB Actuator Remote Control Switchbox
Up to 10 switches
Technical Specifications
Material
Black powder coated aluminium
Weight
100 grams
Operating Temp
-25 to 50°C
DX Connector
2 DX BUS sockets
Storage Temp
-25 to 65°C
Auxiliary Output Current
1A
Size
95 x 61 x 26 mm
33
DX-LM-Z Lighting Module
Provides all of a wheelchair’s lighting requirements.
• 3 channel lighting support for indicators, hazard
lights, driving lights
• No direct battery connections, all power
sourced via the DX BUS
• Short and open circuit detection for lamps
Part numbers
Power
Module
DX-LM-Z
Motor
Motor
DX-LM-Z
Lighting Module
also required – DX BUS cable,
DXLOOM-AUX Connector Kit
Master
Remote
Battery
DX-LM-Z
Lighting System
Technical Specifications
Material
Grey aluminium
Protection rating
IP54
Continuous lighting current
1A (indicators)
2A (driving lights)
Operating Temp
-25 to 50°C
Size
125 x 85 x 29 mm
Storage Temp
-25 to 70°C
Weight
400 grams
DX Connectors
2 DX BUS Sockets
DX-ECU Environmental Control Unit
Environmental control of up to 8 switched outputs using
the same user input device as used for driving.
Power
Module
DX-ECU
Motor
Battery
DX-ECU
Motor
Master
Remote
Part numbers
DX-ECU
8 Relay Switches
Page
Turner
Any
Scan Switched
Device Device
ECU in “8-Output” mode
• Interface to on-chair devices such as laptop
computers or communication aids
• Independent control of up to 8 separate functions
or devices per DX-ECU
• “Mouse mode” for operating a computer mouse
mover
• Up to 2 ECUs can be operated in a single DX system
• Can be used with DX or DX2 master remotes that
support ECU
Computer
Mouse
Mover
ECU in “Mouse” mode
DX-ECU Environmental Control Unit
also required – DX BUS cable
Please note a Master Remote that supports ECU functionality
is required.
Technical Specifications
34
Material
Grey aluminium
Weight
400 grams
Protection rating
IP54
DX Connector
1 DX BUS Socket
Size
125 x 85 x 29mm
SPECIALTY CONTROLS
DX-RJM-MEC Micro Extremity Control
The DX-RJM-MEC (Micro Extremity Control) is a fully proportional mini joystick
with a built in mode change function. The DX-RJM-MEC requires only 18 grams
of force to deflect the joystick. Pushing directly down from neutral position will
activate a mode change.
Ideally suited for users with limited range of motion or low strength, the DXRJM-MEC provides a flexible and easy to mount solution that maximises ability.
The DX-RJM-MEC is available with two mounting options; the DSL-603M tray
mount protects the joystick and provides a place for the hand to rest, and the
swing away DSL-660 Nucleus mount provides a good option for centre line
mounting.
The DX-RJM-MEC is a DX version of the popular ASL130 MEC joystick from
Adaptive Switch Laboratories. Each MEC joystick is supplied with the option of
fitting a finger cup, cork ball, or rubber tip as the user interface to the joystick.
Available Components, Mounts & Spares
DX-RJM-MEC Proportional Micro Extremity Control
DX-RJM-MEC
DSL-603M
MEC Tray Mount
DSL-660
Nucleus Swing Away Mount
DSL-644
MEC Ring Clamp (required for use with the DSL-660)
DSL-MEC-TIPS Spare Finger Cup, Cork Ball & Rubber Tip
Part numbers
DX-RJM-MEC Mini Joystick
Technical Specifications
Material
Black plastic
Size
65 x 25mm dia
Weight
300 grams
DX Connector
1 DX BUS plug on a 2m cable
DX-RJM-HD Heavy Duty Joystick
Heavy duty switched joystick remote for users
who might damage a standard joystick through
rough handling.
• Designed for robustness using heavy
duty switches
• 8 driving directions
Part numbers
DX-RJM-HD Heavy Duty Switch Joystick
also required – DX BUS cable
DX-RJM-HD
Technical Specifications
Material
Black powder-coated aluminium
Size
110 x 85 x 110 mm (including joystick)
Weight
400 grams
DX Connector
1 DX BUS Socket
35
DSL Proximity Head Controls
Clinical Indication
Key features
Non-contact non-proportional control provides
dependable control for users with high or
low muscle tone. The DSL-105 Mini is suitable
for paediatric users or for those who want a
minimally sized head control.
• CE labelled
• Non contact sensors provide more natural where
you look is where you go control
• Side wings adjust in and out to fine tune
positioning to users head
• Mounting hardware adjustable in multiple
directions to allow head control to be positioned
accurately for users with kyphosis or scoliosis
• Sensors easily disconnect to allow for first time
mobility users to experience the control one
function at a time, or for sensors to be allocated
to different control directions
• 3 or 4 Quadrant setups possible
• Used exclusively with the DX-REMG91 and DXACC4B
DSL-105M
DSL-105AE
36
Each DSL-105x Head Control includes:
• 1 x DSL-606 Mounting hardware
• 1 x GSM63160 Interface cable
Bundled Peripherals
Every DSL-105x also comes supplied with:
• 1 x DSL-300 Egg Switch (for mode change and/or
reverse)
• 1 x SWTA5710A Labeled On/Off switch
• 1 x DX-ACC4B Interface electronics
DSL-105STP
DSL-105STA
37
SWTA5020 Mini Joystick with Push
Five switch joystick activation(4 directions, push down
for the 5th switch).
• Can be easily mounted for hand or chin operation
• 9 pin D-type connector
Part numbers
SWTA5020
Mini Joystick with Push
SWTA5020
Technical Specifications
Size
120 x 30 mm
Force
120 grams (200 grams for Push)
PIKO Buttons 9 colours
Colours are Black, Silver, White, Red,
Green, Yellow, Blue, Orange and Gold.
Technical Specifications
38
Sizes
30mm and 50mm diameter
Force
75 grams
Connector
3.5mm Jack Plug
A new range of high quality
low force switches in a range
of candy colours.
Part numbers
30mm
Part numbers
50mm
SWPB30-BLK
SWPB50-BLK
SWPB30-SIL
SWPB50-SIL
SWPB30-WHT
SWPB50-WHT
SWPB30-RED
SWPB50-RED
SWPB30-GRN
SWPB50-GRN
SWPB30-YEL
SWPB50-YEL
SWPB30-BLU
SWPB50-BLU
SWPB30-ORG
SWPB50-ORG
SWPB30-GLD
SWPB50-GLD
Also Available
SWPB-SW5R
(5 Way Button)
Part number
SWPB-SW5R
Buddy Button 6 colours
Robust but sensitive single switch that is available in
a wide range of colours.
Part numbers
SWTA5710
Buddy Button - Red
SWTA5720
Buddy Button - Green SWTA5750
Buddy Button - Yellow
SWTA5760
Buddy Button - Blue
For DX-REMG91S monitored against disconnection
SWJBO200
Jelly Bean Switch (Monitored)
Technical Specifications
Size
20 x 65 mm dia.
Force
100 - 200 grams
Connector
3.5mm Jack Plug
Micro Lever Switch
Small switch with low operating force available in
a range of colours.
Terminated with a 3.5mm jack plug.
Part numbers
SWLA70M, SWLA70MG, SWLA70MR
SWLA70M Micro Lever Switch - Black SWLA70MR Micro Lever Switch - Red
SWLA70MB Micro Lever Switch - Blue
SWLA70MY Micro Lever Switch - Yellow
SWLA70MG Micro Lever Switch - Green
Technical Specifications
Size
40 x 36 x 20 mm
Force
100 grams
Mini Cup Switch
SWTA5808
Very small switch for people with
good targeting ability.
Part numbers
SWTA5808
Mini Cup Switch
Technical Specifications
Size
25mm diameter, 9mm high
Force
130grams
39
CABLES, CONNECTORS & ACCESSORIES
DX BUS Cables
DX and DX2 modules
connect using small, flexible,
4 wire DX BUS cables.
Part numbers
• Available in various
lengths and types to
support a variety of
mounting options
GSM63005
DX BUS cable 0.5m
GSM63010
DX BUS cable 1.0m
GSM63015
DX BUS cable 1.5m
GSM63020
DX BUS cable 2.0m
GSM63025
DX BUS cable 2.5m
Straight Cables
GSM63003DX BUS cable 0.3m
Curly Cables
GSM63051
DX BUS curly cable 0.8m
(compressed)
GSM63052
DX BUS curly cable 1.1m (compressed)
Extension Cables
GSM65433
GSM63081
DX BUS male-female
extension cable 0.3m
DX BUS male-female
extension cable 1.0m
GSM63051
DX-SKT-X3 – DX Bus Expander
Provide additional DX BUS sockets to attach
extra DX modules.
DX-SKT-X3
Part numbers
DX-SKT-X3 Technical Specifications
Size: 14mm x 18mm x 317mm
Weight: 74 grams
40
DX Connectors: 3 DX Bus Sockets
DX BUS 3 Way Socket
GSM9976 5 to 1 Switch Adaptor
This adaptor allows four or five single switches to be used in
place of a multiple switch.
• 9 pin D-type connector (TASH compatible wiring)
• Plugs into DX switch interface modules
• Ideal assessment aid to select locations of single switches
GSM9976
Part number
GSM9976
5 to 1 Switch Adaptor
Technical Specifications
Length
150 mm
Weight
54 grams
GSM9977 Sip & Puff Mounting Kit
A complete set of parts required to operate the Sip
and Puff module.
Contains:
• 21 inch gooseneck
• Air Tube Straws x 2
• Tubing x 1m
• Wheelchair clamp
• Saliva trap
Part numbers
GSM9977
GSM9977
Sip and Puff Mounting Kit
DX Connector Kits
DXLOOM-PM
Part numbers
DXLOOM-PM DX Power Module Connector Kit
# per
Power Module
1
or
GSM60180 DX Battery Connector Kit
1
GSM60182 DX2/DX Motor Connector Kit
2
also
DX connectors are available in kit form or as
pre-assembled looms.
• DX Power module connector kits include
all connectors for the motors and
batteries
GCN60325 DX2/DX Motor Housing
– left or right motor
GCN60326 DX2/DX Motor Housing
– left motor only
GCN60327 DX2/DX Motor Housing
– right motor only
GCN1791 DX Battery Housing
2
1
1
1
• Some are compatible with DX2 Power
Modules as noted below
GCN0787 DX2/DX Motor Housing Cover
1
GCN0788 DX Battery Housing Cover
1
Please note if ordered separately 2 Motor
Connector Kits and 1 Battery Connector Kit
are required for each Power Module.
GCN1781 DX2/DX Motor/Battery Contact
GCN0793 DX2/DX Park Brake Contact
8
4
41
DX2 CONNECTORS
DX2 Power Module Connector Kits
DX2 Connectors are available in kit form or individual parts.
• DX2 Power Module Kits include all connectors for motors and batteries
Part numbers
# per Power Module
Connectors Kits
DX2LOOM-PM1 DX2 Battery & Motor Connector Kit for DX2-PMA70, DX2-PMA90
1
or
DX2LOOM-PM2 DX2 Battery & Motor Connector Kit for DX2-PMA70L, DX2-PMA90L
1
also
Motor Connectors
DX2/DX Motor Connector Kit
2
GCN60326
DX2/DX Motor Housing – left motor only
1
GCN60327
DX2/DX Motor Housing – right motor only
1
GCN60325
DX2/DX Motor Housing – left or right motor (unkeyed)
2
2
GCN60323
Connector Key to configure GCN60325 for left or right use
2
GCN65129
Boot for battery/motor connectors
2
GCN0794
Connector Crimp Contacts for park brake (0.25 – 0.5mm2 wire)
4
GCN0781
Connector Crimp Contacts for motor
4
GSM60182
or
or
Battery Connectors
GME65146
DX2 Battery Connector Housing
1
GCN8002
Connector Crimp Contacts for battery (6 – 10mm2 wire)
2
GCN65129
Boot for battery/motor Connectors
1
Accessory Connectors (required for lights and DCI)
1
GME65147
Accessory Connector Housing
GCN65128
Accessory Connector Boot
GCN0794
Connector Crimp Contacts for 0.25 to 0.5mm wire
7
Connector Crimp Contacts for 1.5 to 2.5mm2 wire
7
1
2
or
GCN0793
42
DX2 Actuator Connector Kits
Available in kit form or individual parts.
Part numbers
# per module
Actuator Connectors Kit
DX2LOOM-ACT Connector Kit for DX2-ACT2/ACT4
1
Connectors and Contacts
GME65345
2 or 4
Actuator Connector housing
GME65347
Actuator Control Input (ACI) connector housing
GME65326
ID Configuration blank plug for ACI (for 1 Actuator module only)
GPC65329A
ID Configuration PCB for ACI (for more than 1 Actuator module)
GCN0794
Connector Crimp Contacts for 0.25 – 0.5mm2 wire
GCN0793
Connector Crimp Contacts for 1.5 – 2.5 mm2 wire
1
1
1
4
4 or 8
DX Lighting and Seating Module Connectors
Available as kits or individual parts.
Part numbers
DXLOOM-AUX DX Auxiliary Connector Kit
# per
Module
1
or
GCN0795 DX Auxiliary Connector Cover
GCN0796 DX Auxiliary Connector Housing
1
1
GCN0793 DX Auxiliary Crimp Pin
21
DX-LOOM-AUX
GME64909 DX BUS Connector Cover
The DX BUS connector protects unused DX BUS sockets
against contamination or accidental short circuit.
Part numbers
GME64909
GME64909 DX BUS Connector Cover
Technical Specifications
Size
16.5 x 12.5 x 10.3 mm
ColourBlack
43
Connector Tools
Crimping, insertion and extraction tools are
available for the pins used in the DX and DX2
connectors.
It is recommended they be used for volume
production of wiring looms.
Positronic Crimp Tool and Turret
CRIMP9999
• For circular Positronic pins (GCN0793,
GCN0794)
• Used for connecting the park brakes, lights and
seat actuators
• Supplied as a separate hand tool and crimp
turret
CRIMP9998
Positronic Insertion and Extraction Tool
• For assembly and removal of the Positronic pins
CRIMP9996
AMP Innergy Tool and Die
• For crimping DX / DX2 motor pins and DX battery
connection pins
• Supplied as a separate hand tool and crimp die
CRIMP9995
Part numbers
CRIMP9994
44
CRIMP9999
Positronic Crimp Tool
CRIMP9998
Positronic Crimp Turret
CRIMP9997
Positronic Insertion Tool
CRIMP9996
Positronic Extraction Tool
CRIMP9995
AMP Innergy Crimp Tool
CRIMP9994
AMP Innergy Crimp Die
DX Pre-assembled Leads
Separate connector covers are also available for
these looms.
• Some are compatible with DX2 Power Modules
as noted below
Part numbers
GSM61190 GSM61191 GSM61192 GCN0788 GCN0787 DX Battery Loom
– 450mm
DX2/DX Left Motor Loom
– 700mm
DX2/DX Right Motor Loom
– 700mm
DX Battery
Connector Cover
DX2/DX Motor Connector Cover
# per Power
Module
1
1
1
1
2
GSM61192
DX-ACC3 Charger Socket Module
Provides separate battery charging
socket for 24 Volt Battery Chargers
up to a maximum of 8A.
Part numbers
DX-ACC3
Charger Socket Module
Power
Module
DX-ACC3
Motor
Motor
Battery
Charger Socket
Master
Remote
Technical Specifications
Material
Plastic
Size
64 x 44 x 49 mm
Weight
160 grams
DX Connector
1 DX BUS Plug on a 1.5 cable
45
SHARK
WHEELCHAIR CONTROL
SOLUTION
47
THE SHARK SYSTEM
The SHARK System is a versatile and cost-effective Powerchair control solution designed to fit the majority
of standard powered wheelchair applications.
Key Features:
•
•
•
•
•
•
•
•
Excellent drive performance and efficiency using separate power and remote modules
Two optional seat actuators driven directly from the power module
Optional full lighting support
Optional attendant control of drive and seat functions
Simple product configuration using the Hand Held Programmer (DX-HHP) or the Wizard PC program
Variety of cable options
Programmable inhibit and speed control functions via the flexible multi-function DCI pins
Dynamic Controls quality and reliability
Remote
M2
24V Battery
Battery
Charger
Power
Module
M1
Bus Cable
Bus
Cable
Attendant
Control Unit
(Optional)
Y-Cable
Wizard
PC-based
Programmer
Bus
Cable
SHARK Remote only
Hand Held
Programmer
SHARK Remote + Attendant Control Unit
SHARK Selection Guide
Application
Drive only
Drive + Actuators
Drive + Lights
DK-REMD01
DK-REMD11
DK-REMD31
DK-REMD21
DK-REMD01B
DK-REMD11B
DK-REMD31B
DK-REMD21B
Drive + Actuators + Lights
Remote
Power Module
DK-PMB40 (40A)
DK-PMB60AL (60A, 2 Act.)
DK-PMB50 (50A)
DK-PMB11 (75A, 1 Act.)
DK-PMB21 (75A, 2Act.)
DK-PMB60 (60A)
DK-PMB21 (75A, 2 Act.)
DK-PMC21 (90A, 2Act.)
DK-PMB01 (75A)
DK-PMC21 (90A, 2 Act.)
DK-PMC01 (90A)
48
DK-PMB31 (75A)
DK-PMB60AL (60A, 2Act)
SHARK REMOTE MODULES
DK-REMD01/11/21/31
DK-REMD01B/11B/21B/31B
The DK-REMD is a stylish modern joystick remote that
is simple to use and configure.
Key features:
• Dynamic Controls Virtual Speed Pot technology
• Circular speedometer
• Field replaceable Bus cables
• Optional low deflection force (version B)
Part numbers
DK-REMD01 (B) Basic Remote for drive only
DK-REMD11 (B) Remote for drive only + 2 Actuators
DK-REMD21 (B) Remote for drive only + 2 Actuators + Lights
DK-REMD31 (B) Remote for drive only + Lights
DK-REMD01B
DK-REMD21B
Technical Specifications
Material
Polymer
Storage Temp
-40 to 65°C
Protection Rating
IPX4
Size
193 x 77 x 119 mm
Operating Temp
-25 to 50°C
Weight
400 grams
DK-ACU
A joystick remote that can be operated by an
attendant or carer.
Key features:
• Control of both drive and actuator functions
• Simple user interface via a speed pot and
toggle switch
Part numbers
DK-ACU Attendant Remote
GSM80951 Y cable 150mm/5.9” length
DK-ACU
Technical Specifications
Material
Aluminium
Storage Temp
-40 to 65°C
Protection Rating
IPX4
Size
127 x 64 x 114 mm (including joystick)
Operating Temp
-25 to 50°C
Weight
305 grams
49
SHARK POWER MODULES
DK-PMB40/50/60/B01/C01
Basic drive only power module.
Key features:
• 40A, 50A, 60A, 75A or 90A power module
• Four fully programmable drive profiles that
simplifies dealer programming
• Flexible programming options for all chair
configurations
Part numbers
DK-PMB60
DK-PMB40
Basic 40A Power Module for drive only
DK-PMB50
Basic 50A Power Module for drive only
DK-PMB60
Basic 60A Power Module for drive only
DK-PMB01
Basic 75A Power Module for drive only
DK-PMC01
Basic 90A Power Module for drive only
DK-PMB60AL/11/21/31
DK-PMC21
Built on the successful drive only family, these
power modules offer integrated lights and up to 2
actuators.
Key features:
• Optional 1 or 2 built in actuators
• Optional built in lighting
Part numbers
DK-PMB21
DK-PM60AL
60A Power Module for drive + 2 Acutators
+ Lights
DK-PMB11
75A Power Module for drive + 1 Actuator
DK-PMB21
75A Power Module for drive + 2 Acutators
+ Lights
DK-PMB31
75A Power Module for drive + Lights
DK-PMC21
90A Power Module for drive + 2 Acutators
+ Lights
Technical Specifications
50
Material
Die cast, powder coated
Storage Temp
-40 to 65°C
Protection rating
IPX4
Size
181 x 111 x 48 mm
Operating Temp
-25 to 50°C
Weight
960 grams
SHARK CABLES
Shark BUS Cable
One cable is required to connect remote module
to power module. Available in a variety of lengths.
Part numbers
GSM802412.5m/8’2”
GSM802422.0m/6’6”
GSM802331.5m/4’11”
GSM80234
1.0m/3’3”
GSM802360.5m/1’7.7”
GSM80234
Shark BUS Extension Cable
May be used to extend standard bus cable if required.
Part numbers
GSM80203300mm/1ft
GSM80220
300mm/1ft (with panel mounting spring)
GSM80211640mm/2’1”
GSM80221
640mm/2’1” (with panel mounting spring)
GSM802310.9m/2’11”
GSM80224
GSM80231
0.9m/2’11” (with panel mounting spring)
GSM802321.2m/3’11”
Motor/Park Brake Leads
Part numbers
GSM61191
700mm/2’3.5” Motor 1
GSM61191P
700mm/2’3.5” Motor 1(Keyed/Polarized)
GSM61192
700mm/2’3.5” Motor 2
GSM61192P
700mm/2’3.5” Motor 2 (Keyed/Polarized)
GSM61191
Battery Leads
Part numbers
GSM80204
0.5m/ 1’7.7”
GSM802131.0m/3’3”
GSM80204
51
SHARK CONNECTORS
Battery & Motor Kits
Battery and Motor connectors are sold as kits. Each kit
includes housings, connector boots and all required pins.
Part numbers
GSM80210
Unkeyed motor + Battery Connector Set
GSM80209
Keyed motor + Battery Connector Set
GSM80208
Battery Connector Set
GCN60325
Single Motor Connector Kit-unkeyed
(use when ordering one-off)
GCN60326
Single Motor Connector Kit
– Left keyed
GCN60327
Single Motor Connector Kit
– Right keyed
GCN60323
Connector Key to configure GCN60325 for left
or right
GSM60182
Note: DX2 battery and motor connectors can also be used
with Shark. See pages 41 and 42.
DCI Port 4 Way
DCI connectors sold as a complete kit (including housing
and pins) or as individual housings and pins.
Part numbers
GSM80206
4 Pin Kit (inc housing and 4 pins)
GCN8005 GCN0978 Individual Connector Housing (AMP Mate Nlok2 Mini 4W Hse #794188-1)
Individual pins 16-20 AWG (AMP Mate Nlok2 Mini receptacle #794223-1)
GSM80206
DCI Port 12 Way
DCI connectors sold as a complete kit (including housing
and pins) or as individual housings and pins.
Part numbers
GSM80226
52
GSM80226
12 Pin Kit (includes housing and 12 pins)
GCN8004 GCN0691 Individual Connector Housing (AMP Mate Nlok2 Mini 12W Hse #172170-1)
Individual pins 16-20 AWG (AMP Mate Nlok2 Mini receptacle #794231)
R-SERIES
SCOOTER CONTROLLER
53
R-SERIES SCOOTER CONTROLLERS
The R-Series is a high quality, value for money scooter
controller that will provide a refined drive experience,
available in 50A and 90A versions.
Key features:
• Programmable acceleration curves, improved
rollback on slopes and motor matching algorithms
ensuring improved curb-climbing and hill-starting
capabilities
• Speed reduction wiper (SRW) technology provides a
seamless speed reduction in turns for extra stability
DR50-A01
• Throttle Dual Decode* signal processing to comply
with ISO7176-14 (2009) (D variants)
• Intelligent motor and battery management
• Support for a range of battery types, multifunction
pins and flexible drive inhibits
• Advanced diagnostics and servicing tools, including
event and drive time logging, and programmable
servicing scheduler
• 2 x Drive profiles, brake and reverse lights, reversing
beeper and electronic park brake release
• Compact design with IPX4 ingress protection
• Industry standard connections and mounting
DR90-A01
• Complete set of all connectors required to install
R-Series controllers
• Designed to exceed IS0 7176-14 Standards
R-series
*requires ISO compliant speed pot
Motor
Tiller
Battery
Part numbers & Specifications
Head
Part Number Description
Peak Current
Peak Current
Duration
Continuous
Current
Boosted Current
(8 sec)
DR50-A01
50 Amp
40A
<60 sec
14A
50A
DR50-B01
50 Amp †
40A
<60 sec
14A
50A
DR50-AD01
50 Amp with Dual
Decode* functionality
40A
<60 sec
14A
50A
DR50-BD01
50 Amp † with Dual Decode* functionality
40A
<60 sec
14A
50A
DR90-A01
90 Amp †
70A
<60 sec
20A
90A
DR90-AD01
90 Amp † with Dual Decode* functionality
70A
<60 sec
20A
90A
† Compatible with metal cover
* requires ISO compliant speed pot
Technical Specifications
Material
Aluminium base & plastic
cover (V-0 rating)
Protection rating IPX4
54
Operating Temp -25 to 50°C
Storage Temp -40 to 70°C
Connectors
Junior mini fit logic connectors
Size
131.5 x 72.5 x 40mm
QC tabs for motor and battery
Weight
260 grams
R-SERIES ACCESSORIES
Part
Part number
QTY
Flammability
DR-metal case cover
GME52168
1
N/A
DR-metal case grommet
GCH52169
1
V-0
Terminal Female 12-14AWG for Tyco 250 Series Lance Connector
GCN0690
10
N/A
Crimp Terminal 18-24AWG Molex Minifit Jnr
GCN0771
16
N/A
Crimp Terminal 16AWG Molex Minifit Jnr
GCN0776
4
N/A
Housing 2 Pin Molex Minifit Jnr
GCN0884
1
V-0
Housing 4 Pin Molex Minifit Jnr
GCN0886
1
V-0
Housing 14 Pin Molex Minifit Jnr
GCN0887
1
V-0
R-SERIES CONNECTORS
DR-CONSETA
Complete set of all connectors required to install
R-Series controllers.
Part numbers
DR-CONSETA R-Series Connector Kit
55
RHINO2
SCOOTER CONTROLLER
57
RHINO2 SCOOTER CONTROLLER
RHINO2 - High Power Scooter controller
DS160C*, DS160, DS180
DS70C*, DS90, DS110C* & DS120
Rhino2
Motor
Battery
Tiller
Head
Universal terminal
cover
*Classic models have a grey shot finish.
The Rhino2 and Rhino2 Classic are Dynamic Controls’ most powerful and
advanced scooter controllers yet. Rhino2 and Rhino2 Classic deliver powerful boost
current when you need it, peak stated amperage for up to a staggering 3 minutes
and an incredible continuous current rating, all in a compact rugged design.
Rhino2 and Rhino2 Classic offer superior drive control, optimised ride comfort and is
highly configurable, making it suitable for a wide variety of scooters.
Technical Specifications
Material
Aluminium base & Plastic
Protection rating IP54
58
Operating Temp -25 to 50°C
Storage Temp -25 to 70°C
Connectors Junior mini fit logic connectors
Size
153 x 100 x 44mm
QC tabs (DS90 & 120) for motor and battery
Weight
1 kg
M5 screw terminals (DS160) for motor and battery
Key features:
• 70 Amp, 90 Amp, 110 Amp, 120 Amp, 160 Amp and 180 Amp models available
• With boosted power of 90 Amp, 100 Amp, 130 Amp, 140 Amp, 180 Amp and 200 Amp, Rhino2
delivers the power you want when you need it
• Compact design with more power from the same footprint
• Programmable acceleration curves, improved rollback on slopes and motor matching algorithms
ensuring improved curb-climbing and hill-starting capabilities
• Motor open and short circuit testing while driving allows detection of broken brushes
• Improved downhill speed control to maintain or reduce speed on slopes as desired
• Enhanced thermal and current control to extend life of motors and controllers
• Speed reduction wiper (SRW) technology provides a seamless speed reduction when turning for
extra stability
• Throttle Dual Decode* provides extra safety in case of a throttle failure, and allows manufacturers to
comply with the requirements of ISO7176-14 (2009)
• Intelligent motor and battery management providing automatic power flow optimisation, auto
battery configuration, 5V and 12V battery capacity outputs and in-depth battery logging and
analysis tools
• Support for a range of battery types, multifunction pins and flexible drive inhibits
• Advanced diagnostics and servicing tools, including event and drive-time logging, and
programmable servicing scheduler
• 2 x drive profiles, brake and reverse lights, reversing beeper and electronic park brake release
• A separately available aluminium top cover provides maximum protection against water splashes
and mechanical protection to terminals
• IP54 ingress protection
• Lead-free RoHS compliant
• Designed to exceed IS0 7176-14 Standards
* Requires ISO compliant speed pot
Part numbers & Specifications
Part Number
Description
Peak Current
Peak Current
Duration
Continuous
Current
Boosted Current
(10 sec)
DS70C
70 Amp
70A60s 25A90A
DS110C
110 Amp
110A
60s
43A
130A
DS160C
160 Amp
160A
60s
50A
180A
DS90
90 Amp
90A
3 minutes
36A
100A
DS120
120 Amp
120A
3 minutes
48A
140A
DS160
160 Amp
160A
3 minutes
64A
180A
DS180
180 Amp
180A
60s
64A
200A*
* The DS180 has a Boosted Current of 200A for 5 seconds.
59
Rhino2 Accessories
Part
Part Number
Quantity
Flammability
DS90 Motor/Park brake Adaptor Loom
GLM51981
-
V-2
DS120 Motor/Park brake Adaptor Loom
GLM51983
-
V-2
RHINO2 Battery/Actuator Adaptor Loom
GLM51984
-
V-2
RHINO2 Motor-4/Ring Terminal Adaptor Loom
GLM51985
-
V-2
RHINO2 Battery-6/Ring Terminal Adaptor Loom
GLM51986
-
V-2
RHINO2 Logic Adaptor Loom
GLM51987
-
V-0
Loom Kit RHINO2 Logic
GSM51982
-
V-0
Loom Kit RHINO2 4W Motor + 6W Battery
GSM51988
-
V-0
Loom Kit RHINO2 Ring Terminals
GSM51989
-
V-0
Crimp Terminal M5 Ring Yellow 10-12AWG
GCN1286
8
V-0
Crimp Terminal Female Spade 18-22AWG Red Insulated
GCN1282
2
V-0
Tyco 250 Series Lance Connector Housing 4 Way Plug
GCN0688
1
V-2
GCN51970 1V-0
Tyco 250 Series Lance Connector Housing 6 Way Plug
GCN0689
1
V-2
GCN51971 1V-0
Terminal Female 12-14AWG for Tyco 250 Series Lance Connector
GCN0690
10
N/A
Crimp Terminal 18-24AWG Molex Minifit Jnr
GCN0771
16
N/A
Crimp Terminal 16AWG Molex Minifit Jnr
GCN0776
4
N/A
Housing 2 Pin Molex Minifit Jnr
GCN0884
1
V-0
Housing 4 Pin Molex Minifit Jnr
GCN0886
1
V-0
GCN0887
1
V-0
GME51934
-
N/A
Housing 14 Pin Molex Minifit Jnr
Terminal Cover (with three screws)
60
PROGRAMMING
FOR DX/DX2, SHARK, R-SERIES & RHINO2
61
PROGRAMMING
Dynamic Controls provides two programming tools for configuring products:
• Hand Held Programmers (HHP) - a convenient hand held device.
• Wizard – PC Programming tool
Note - Programming tools for LiNX products are covered in the LiNX section of this catalogue.
HAND HELD PROGRAMMERS
The Hand Held Programmers (HHP) allow wheelchair and scooter manufacturers, dealers and health
professionals to adjust the system settings to suit a particular wheelchair, scooter or individual.
Key features:
• Access to the most commonly changed settings
• 4 line full text display
• Easy to understand fault conditions
DX-HHP
DX-HHP
The HHP is sold as a complete kit that includes all
the required adaptors. It is compatible with DX2,
DX, Shark, R-series and Rhino2.
Part numbers
DX-HHP
62
Hand Held Programmer for all products except Rhino
WIZARD PC PROGRAMMING TOOL
Wizard is a software programming tool designed to
program, configure and diagnose all products from
Dynamic Controls. It is intended for manufacturers,
dealers and therapists.
Key features:
• Operates under Microsoft Windows
• Supports all Dynamic Controls products except
LiNX (see page 8 for LiNX Programming).
• Simple to use
Part numbers
DWIZ-KIT
Wizard program on CD plus all cables
& adaptors
DWIZ-KIT
Dongles
A dongle is a hardware security device that plugs
into your computer to prevent unauthorised
access to product parameters. Product safety and
integrity are protected by the dongle. Using the
correct dongle level ensures Wizard operators only
have access to functions they are trained to use.
Part numbers
DWD-OEM-U
DWD-DLR-U
Dealer – Allows customisation to specific users
DWD-EDL-U
Enhanced Dealer – Dealer access plus ability to edit auxiliary function options
DWD-OEM-U OEM – access to all parameters required by a manufacturer
DWD-FAC-U
Factory – prevents unauthorised changes in a production environment
63
Programming Adaptors and Wizard Kit replacement parts
In the event of loss or accidental damage
replacements can be ordered individually.
Part numbers
DWIZ-CABLE Wizard Communications Cable
DWIZ-ADAPT Programming adaptor for DX2, A-series,
R-series & Shark*
DX-USB-COM Serial to USB adaptor
DWIZ-S/W Wizard software on CD
DK-ADAPT
DX-HHP to Shark adaptor
DR-PRGLM02 Used with DWIZ-ADAPT for R-series without a charger socket
*Can be used between Wizard and Shark but not
DX-HHP and Shark
64
ACCESSORIES
65
65
ACCESSORIES
Charger Plug
3 pin plug for connecting battery chargers to all
Dynamic Controls wheelchair and scooter controls.
Part numbers
GCN0309
Charger Plug
Connections: Pin 1
Pin 2
Pin 3 B+, Battery Positive
B-, Battery Negative
Linked to Pin 2, inside plug
Linking pins 2 and 3 inside the charger plug will stop the
wheelchair or scooter from being driven away with the
battery charger plugged in.
Circuit Breakers
Part numbers
GCK0011
GCK0011
Circuit Breaker – 40A
GCK0014
Circuit Breaker – 60A
Joystick Knobs
Alternative fittings to add to any Dynamic Controls
joystick to enable customisation for an individual.
Part numbers
Clockwise from top left: Sponge Ball, Golf Ball Knob,
Finger Tube, Wrist Plate, Round T-Bar, Straight Bar, Flat
T-Plate, Joystick Knob, Joystick Skirt (towards middle), DL
Knob, Carrot Knob, Standard Ball Knob (towards centre),
Chin Cup.
66
GJS0003
Standard Ball Knob (30 mm)
GJS0031
Carrot Knob
GJS0040
DL Knob
GJS26819
Chin Cup (use with GJS0029)
GJS26826
Sponge Ball (use with GJS0029)
GJS9983
Golf Ball Knob
GJS0029
Joystick Metal Insert
GJS0022
Wrist Plate (chrome)
GJS0033
Round T-Bar (chrome)
GJS0044
Flat T-Plate (chrome)
GJS0055
Straight Bar (chrome)
GJS0066
Finger Tube (chrome)
GJS0090
Joystick Knob
GJS0091
Joystick Skirt
Magnetic Key
For use with Master Remotes that have the
magnetic keylock feature.
Part numbers
DC-MKEY Magnetic Key
DC-MKEY
67
EUROPE
ASIA
AUSTRALASIA
USA
Ph: +44-1562-826-600
Ph: (Taiwan): +886-955-335 243
Ph: +64-3-962-2519
Ph: +1-440-979-0657
Fax: +44-1562-824-694
Ph: (China): +86-512-6289 2847
Fax: +64-3-962-2966
Fax: +1-440-979-1028
[email protected]
+86-512-6289 2823
[email protected]
[email protected]
+86-512-6289 2803
(CORPORATE OFFICE)
Fax: +886-2 -2598 1562
[email protected]
Dynamic Controls is the world’s leading manufacturer of electronic controls for power wheelchairs and scooters.
Dynamic Controls was established in 1972 and is headquartered in New Zealand.
Regional centres are located in Europe, United States, Asia, and Australasia.
ISO 13485 certified – Dynamic Controls goes above and beyond industry standard expectations to ensure customers receive the best products possible.
www.dynamiccontrols.com
GBR59617 DYNAMIC Catalogue 2014
Actual products may vary from those featured due to Dynamic Control’s policy of continuous improvement. Not all products are available at the time of printing.
Specifications may be subject to change. The DX system is TUV certified. All released DX2 modules are currently TUV certified.