Your Bucket Tooth - Plasterer Equipment Company

Transcription

Your bucket tooth
information source including
product features,
applications
and specifications for the
following product lines:
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Fanggs
Deere
Caterpillar replacement
Hensley replacement
Esco Conical replacement
Esco SuperÔ
Esco Helilokâ/Vertalokâ
H & L replacement
Rippers and scarifiers
Bucket Tooth Basics
Tooth Performance and Wear Life
Tooth Performance and Wear Life
Maximum performance and wear life are the two
most important characteristics for replacement
teeth. Working with constant abrasive material
places extreme demands on both design and
strength.
Design
=
Performance
Strength
=
Wear Life
The best designed tooth is always a compromise
of performance and wear life.
Design is directly related to performance while
strength is directly related to wear life.
Tooth Penetration
Penetration is a key design consideration for all
replacement teeth.
To Achieve Good Tooth Penetration
To achieve good penetration, a tooth must have a
sharp point for initial ground entry.
The tooth blade must taper gradually enough to
reduce resistance to penetration and yet be thick
enough to avoid breakage.
1. Tooth must have sharp point.
2. Blade must taper gradually to reduce
resistance.
3. Blade must be thick enough to avoid
breakage.
The easier it is to penetrate the material…the less
horsepower is required for operation.
Tooth Centerline vs. Non-Centerline Design
All centerline points are reversible to distribute wear and stay sharp.
Non-centerline points can be rotated to balance wear patterns, but they cannot be “flipped over” to
resharpen.
PI7262 Litho in U.S.A. (97-02)
Basics
1
Bucket Tooth Basics (Continued)
Tooth Breakage
Tooth wear is expected, but tooth breakage
under normal working conditions is not!
Tooth Installation
The job of a tooth retainer is to withstand
impacts or shocks transmitted through the tooth
without breaking or falling out. It must also
take up manufacturing tolerances so the tooth
stays tight on the adapter.
Tooth breakage in extreme conditions - very
hard abrasive material where blasting, ripping,
or air hammering might be more effective should be expected.
The various types of “hardware” to install teeth
are covered in detail within each section. These
are some types of hardware or retainers used:
The worst thing an operator can do is use the
bucket with missing teeth. A missing tooth
exposes the adapter nose piece to wear. Any
amount of worn metal from the adapter
nosepiece leaves an open pocket between the
adapter and the replaced tooth. This open area
allows the tooth to work back and forth. The
adapter can no longer provide the support
necessary to firmly attach the tooth to the
bucket. To find out if the nosepiece is the
reason for the tooth breakage, remove the tooth
tip. If the nosepiece is worn, the original shank
or adapter should be replaced.
Flex Pin
Spring Pin
Horizontal Pin and Split Washer
Roll Pin
Groove Pin
Crimp-On
Pin and Lock
Quadrilok®
Pin and Plug
Tooth Wear
It is a good idea to inspect bucket teeth,
adapters, and the bucket condition daily. By
determining wear patterns and rotating teeth,
you can extend wear life and increase
productivity which, in turn, provides you the
greatest return for the money invested.
When using the right tooth and operating the
bucket according to standard practice, a pattern
will develop for normal wear. The tooth will
maintain a profile similar to the original profile
and it will continue to penetrate material
quickly and easily.
But even when using the right tooth, tooth
wear is seldom even. Teeth that are near bucket
corners generally wear fastest. And a bucket
that is regularly loaded at an angle will show
uneven wear on the loading side. Rotating
teeth will help equalize the wear.
Both abnormal wear and breakage can be
prevented with the right choice of teeth. Some
suggestions include reducing the size and
length of the point or switching to a forged or
cast tooth when material becomes harder and
more abrasive.
While teeth could assume the shape of a fist
due to improper use of the bucket such as
scraping, dragging, or banging, it is most likely
that the wrong teeth are being used for the
application. Using the wrong teeth for the
application takes more power to penetrate
material and reduces productivity.
Basics
2
Bucket Tooth Basics (Continued)
Tooth Position
FANGGS teeth have a curved shape to extend the contour of the bucket which results in a continuous
flow of material to achieve maximum bucket fill. Reversing Fanggs teeth so that the curve of the
tooth is opposite that of the bucket is not recommended.
Forged and cast backhoe and excavator teeth
can be reversed as shown in this drawing. The
flat of the tooth faces away from the open side
of the bucket. As you can see, tooth angle is
less aggressive. Teeth can be mounted in this
position to avoid disturbing the trench floor.
Teeth other than Fanggs installed on backhoe
and excavator buckets are mounted as
indicated in the above illustration. The flat area
of the tooth faces the open part of the bucket.
In this position, tooth entry into the ground is
very aggressive. It allows the teeth to break
material for easier bucket loading. It is
recommended that teeth be mounted in this
position for normal digging conditions.
It is not recommended that fabricated teeth be
mounted in this reversed position. As the
bucket is being loaded, material will wear thin
the clip portion of the tooth. Eventually, tooth
breakage will occur. The clip is made of a
softer metal and as a result is more susceptible
to wear than the blade portion of the fabricated
tooth.
Basics
3
Adapter Installation
Various retention methods between the adapter and bucket as well as the tooth and adapter are
available.
Check the condition of the bucket and repair as necessary before installing an adapter.
3. On hydrostatic crawler loaders, preheat
the cutting edge holes (second set from
each end) to 400˚F (204˚C).
Bolt-On Adapters
When installing a new adapter, be sure the
cutting edge provides a firm mounting base. If
the edge has been worn and doesn’t provide
support, the adapters are susceptible to
breakage.
Always use the attaching hardware
recommended for the application. Bolt tensile
strength has been matched to specific
application requirements.
Weld-On Adapters
4. Use a temperature stick (Tempilstik or
equivalent) to check preheat temperature.
Warning: Persons performing welding and
other maintenance work should wear OSHAapproved safety equipment such as hard hats,
safety shoes and glasses, work gloves, and the
proper lenses in welding gear.
When welding adapters to the bucket cutting
edge, make sure the cutting edge provides a
firm mounting base. This support is necessary
as adapters are also susceptible to breakage.
Welding to the bucket cutting edge may cause
cracks in the cutting edge if a firm mounting
base is not provided and good welding
techniques are not followed:
5. Fill the holes with plug welds.
1. Remove the tooth and pin from the adapter
prior to welding. High welding
temperatures can have a detrimental effect
on tooth heat treatment.
2. Clean the area to be welded. Remove paint
by sanding or grinding. Remove oil and
grease using a safe solvent. Remove rust
and dirt using a wire brush.
6. Grind weld flush with top cutting edge
surface.
Basics
4
Adapter Installation (Continued)
9. Use a smaller diameter (0.12″ (3 mm)
maximum) electrode to make the Jgroove welds with an unequal leg fillet
weld (2). Extend the longer leg onto the
cutting edge.
7. Tack weld the rear of the adapter to the
cutting edge.
8. Preheat adapter to 400-600˚F (204306˚C) before welding. Use a
temperature stick to check for correct
temperature.
10. Start at the rear of the adapter. Weld one
pass to 1″ (25.4 mm) from the edge (4).
Weld one pass on the other side of the
adapter.
11. Chip off the slag and peen each weld
bead after each pass. Alternate from one
side of the adapter to the other side for
each pass.
12. After all adapters are welded, uniformly
heat the edge and all adapters to 400˚F
(204˚C). Let the adapters and cutting
edge cool slowly in still air.
Basics
5
Manufacturing Process
ADI Teeth
Austempered ductile iron teeth are used on backhoes, excavators and loaders. They offer moderate
to heavy impact resistance. An ADI tooth is essentially a cast tooth of different chemistry, ductile
iron which is brought to heat in a controlled environment (austempering). John Deere has a video
offering further explanation of ADI (DGVHI93821 available from DSC).
The pattern is then mounted on an automatic
molding machine. This machine takes
preconditioned sand that has been mixed with
clay and water and compresses the sand against
both sides of the pattern plate to form the two
halves of the mold. These two halves of the
mold are pulled away from the pattern leaving
detailed impressions in the sand. Then the shell
cores are strategically placed into the imprint.
Now the two halves are joined forming the
casting impression.
The molds are next transferred by conveyor to
the mold handling system. A metal jacket is
placed around each mold to insure that no side
movement occurs between the mold halves.
The weight is set on top of the mold to apply
additional pressure so that no separation occurs
as the pouring process is completed.
The manufacturing of ADI teeth starts naturally
with an engineering drawing of the part itself.
From the drawing, critical dimensions are
utilized to machine a metal pattern.
The pattern is then used to manufacture prototype castings. These are evaluated by
engineering to confirm the design. If any
pattern adjustments are required, additional
tooth samples are produced and final approval
authorized.
The combination of the following metals
provide high strength and ductility:
• Pig iron
• Manganese
• Steel
• Along with other alloys including
carbon and silicon
The pattern forms the outside shape of the
tooth. It incorporates the gating system which
is the path the molten metal flows through to
the actual tooth cavities.
All of these materials have the necessary
metallurgical chemistry to meet John Deere’s
strict specifications.
Although the pattern forms the outside shape
of the tooth, the pocket area is formed by a
core. The core is produced in a metal machined
core box. The box is injected under pressure
with a resin-coated sand.
This raw material is carefully weighed so that
there is a consistent cross match of ongoing,
solid, raw material with an outgoing molten
ductile iron.
By using heat, the resin-coated sand grains
bond together forming a shell core. The shell
core is dipped into a liquid metal protectant
which provides a smooth pocket and accurate
pin hole location.
The charge vessel is moved in place over the
electrical furnace and material is released.
After approximately 15 minutes, the material
will be heated to about 2700 degrees
Fahrenheit and will be transformed into a
liquid state.
Basics
6
Manufacturing Process (Continued)
ADI Teeth (Continued)
Cast Teeth
The metal undergoes chemistry analysis to
monitor quality standards.
Cast teeth are used on loaders, scrapers,
rippers, and scarifiers. They are formed from a
medium-carbon, chromium, nickel,
molybdenum steel offering high strength and
toughness with deep-hardening properties.
They have excellent resistance to wear and
abrasion.
The iron is then poured into an inoculation
ladle, magnesium is added, and it is then
transferred to the pouring area.
The manufacturing process begins with the
pattern which is basically an exact duplicate of
the tooth to be cast but slightly oversized to
compensate for steel contraction. The mold is
made from this pattern.
The mold consists of silica sand and binder. It
contains the cavity into which the molten metal
will be poured in order to form the casting. The
mold is made in two sections with the top half
referred to as the cope and the bottom as the
drag.
The iron pourer will check the molten iron for
proper pouring temperature and magnesium
inoculations. If the material passes inspection,
molds are poured. The metal travels through
the gating and fills each tooth cavity.
The core is also made of a sand mixture. When
placed in the mold, it forms the tooth pocket
area. At this point, liquid cement is applied to
the cope and drag. Clamping fixtures press the
two pieces together.
Once poured, the carousel moves the mold to
the cooling chamber for a specified time.
Afterwards the teeth are removed mechanically
and pass down the shake-out area. This
removes the majority of sand from the casting.
Metal is placed into the furnace for the melt
process. The melt process begins as three, 8inch (203 mm) diameter graphite electrodes
moving in tanden work their way downward
through the charge. An electric arc is
maintained between the electrodes and the
charge. When the electrodes reach the bottom,
the initial transformation to liquid steel takes
place. The entire charge is then transformed
into liquid steel as the electrodes slowly return
upward. At this point, the temperature of the
steel is approximately 2900˚F (1593˚C).
The castings are now transported to the
tumble-blast area for final cleaning.
They are shuttled to a grind step to remove the
end gates and any protrusions.
Quality assurance and analysis occurs
throughout the processes. Constant monitoring
of the sand and metal micro structure ensure a
high quality casting.
Following the adjustments dictated by steel and
slag samples taken to determine carbon level
and stage of melt process, the melt is refined.
Temperature is raised to 3200˚F (1760˚C), and
tested again to determine if alloy adjustments
are necessary. The entire melt is then poured
into a tapping ladle, reladled into small pouring
ladles, and poured into the mold.
Spectrographic analysis is also constantly
performed to provide proper metal chemistries.
Inspection steps continue as Brinell Hardness
and additional quality audits are consistently
administered.
In final process, the castings undergo an
austempering heat treatment. This makes the
final product stronger, harder, tougher.
Basics
7
Forged Teeth
Cast Teeth (Continued)
Forged teeth are used on backhoes, loaders,
excavators and motor graders.
Chrome-moly alloy steel along with the
continuous fibre structure and grain flow of the
steel provide increased strength while
maintaining hardness. Forged teeth have a high
tensile strength while maintaining excellent
ductility.
After cooling, the teeth are run through a
shakeout to remove the mold and cores.
Castings go through an additional cleaning
operation to remove all sand. Using acetylene
torches, excess material is removed from the
teeth which then go through a finishing grind
to remove all excess metal.
Forged teeth are produced from steel bars and
billets with specified and carefully controlled
analysis. The raw material is cut to size and
heated in electric induction heating units to
forging temperatures. Electrical heating
provides a much higher quality product than
gas heating.
Following heating, the part undergoes up to ten
steps in the forging process to form the tooth
from the solid steel billet. After forging, the
individual parts are inspected, hand finished,
and then sent on to heat-treating.
All John Deere cast teeth are differentially
heat-treated to provide the hardness, wear
resistance, and toughness for the longest, most
productive life.
In the heat-treating process, the teeth are
individually placed in containers to provide
thorough and even heating. Next, they are
loaded into endothermically-controlled
atmosphere furnaces where they are heated to a
closely controlled temperature. This type of
furnace allows the surface chemical analysis of
the part to be maintained and ensures that the
part will be heat-treated to the maximum
attainable hardness. Following the hardening
process, the teeth are tempered and inspected
for hardness.
Basics
8
Two pieces - the blade and the clip - comprise
the fabricated tooth. Since the blade incurs
most of the wear, it is made of chrome-nickelmoly alloy steel heat-treated to Rockwell C4550. The clip is shaped to form the exact pocket
size required for precise adapter fit. It is
electronically welded to the blade and then
heat-treated and tempered.
Fabricated Teeth
Fabricated teeth are used on backhoes,
excavators, and motor grader rippers. They are
standard-duty teeth which are self-sharpening
and feature easy replacement and economy.
Nodular Iron Teeth
Nodular iron teeth are available on utility
crawler loaders. These teeth are a one-piece,
bolt-on type. They are generally used in lightduty applications.
Basics
9
Hardness Testing
Two tests are commonly used for hardness testing.
Charpy Test (Impact Stronger)
Brinell Hardness
A test bar (a small metal bar from a pour
approximately 6” long) is notched and placed
on the anvil. The hammer portion of the testing
machine is released with adequate force to
break the sample. The scale measures the
energy absorbed by the sample during the
fracture. The farther the pendulum swings
through the sample, the more brittle the
material.
The Brinell Hardness Number (BHN) is one of
the oldest tests and is the most common
standard. The tooth is placed on the anvil and a
steel ball is pressed into the sample with a load
of 3000kg. The load is then left in place for 30
seconds and then removed. The diameter of the
impression is then read in millimeters with a
low power microscope with a measuring
eyepiece and the BHN is determined.
John Deere’s charpy range is from 17-19 which
indicates excellent impact strength.
The BHN in John Deere’s product line is
475-500.
Basics
10
Warranty
or labor for tooth removal and installation; all
other remedies are expressly excluded.
Guaranteed against breakage! Warranty applies
to a John Deere ADI, cast or forged
replacement tooth that breaks during operation
before it wears out provided: (1) the tooth has
not been hard faced or repaired, (2) it is used
on a matching tooth adapter, and (3) the tooth
support surface of the adapter has been
properly maintained. A new tooth of the same
type will be furnished free of charge by any
authorized John Deere industrial dealer.
In addition, John Deere’s normal parts
warranty and its terms and conditions (see John
Deere Service Parts Warranty for details)
applies to any ADI, cast or forged tooth under
the above warranty which may otherwise prove
defective in material or workmanship within 90
days after purchase.
John Deere’s obligation under this warranty
does not cover hardware for attaching the tooth
Basics
11
Tooth Pocket Dimensions
(Refer to Replacement Section for Specific Part Numbers)
At times, part number information is not always readable on a worn tooth.
There are several ways to identify a design and then a specific part number:
1. Tooth Pocket Dimensions
Measure the tooth pocket width and height and reference the dimensions
in the list below to isolate the tooth type (Caterpillar, H & L, Hensley, etc.)
and series. Then look in the corresponding replacement section which
includes photos, line drawings, and dimensions to establish the tooth
needed for the application.
2. Retention Hardware
Use the actual size illustrations of the retention hardware included at the
end of each replacement section to determine possible tooth type
(Caterpillar, H & L, Hensley, etc.) and size.
Tooth Pocket Width
1-13/32″
1-1/2″
1-9/16″
1-9/16″
1-5/8″
1-5/8″
1-3/4″
1-13/16″
1-15/16″
2-1/16″
2-1/4″
2-3/8″
2-1/2″
2-11/16″
2-7/8″
2-7/8″
3″
3″
3-5/32″
3-13/32″
3-1/2″
3-1/2″
3-17/32″
4″
4″
4-5/16″
4-1/2″
4-3/4″
4-7/8″
6″
Tooth Pocket Height
1-27/32″
1-5/8″
1-11/16″
2-1/8″
1-5/8″
2-3/8″
2-11/32″
1-1/2″
2-11/16″
2-1/8″
2-1/8″
3-1/32″
2-1/8″
3-5/16″
2-1/8″
2-11/16″
2-1/8″
2-1/4″
3-21/32″
3-3/16″
2-5/8″
2-7/8″
3-29/32″
2-7/8″
3″
4-11/32″
3-1/4″
3-1/2″
5-1/2″
5−29/32″
Replacement Section
Caterpillar
H&L
H&L
H&L
Hensley
Hensley
Caterpillar
Esco Conical
Caterpillar
H&L
Hensley
Caterpillar
Esco Conical
Caterpillar
H&L
Hensley
Hensley
Esco Conical
Caterpillar
Hensley
Esco Conical
Hensley
Caterpillar
Hensley
Esco Conical
Caterpillar
Esco Conical
Hensley
Caterpillar
Caterpillar
Tooth Pocket Dimensions
1
Series
20
23
–
24
156
160
22
18
25
25
220
30
25
35
27
290
310
30
40
330
35
350
45
400
40
55
45
475
45 Abrasion (Standard)
70
Fanggs Teeth: A John Deere Exclusive!
Better Bucket Fill
Better Level Bucket Operation
Better Start-Dig Characteristics
Exclusive to John Deere
Whether it is breaking-up gumbo, slicing
through frost, moving hard-packed sand, or
general-purpose digging, Fanggs will answer
the call! The patented, guaranteed-againstbreakage, competitively-priced Fanggs teeth
provide better bucket fill, better level bucket
operation, and better start-dig characteristics
due to their design.
Curved Profile
Fanggs teeth are curved. That is why they dig with less effort. The curved profile allows them
to closely track the path of the bucket. Conventional teeth work against the bucket as they pass
through the soil.
Without Fanggs Teeth
With Fanggs Teeth
Better Bucket-Fill and Faster Cycles with Fanggs Teeth
You get better bucket-fill and faster cycles with Fanggs teeth because the rolling action causes the soil to collect at the
back of the bucket instead of the middle.
Fanggs/John Deere
1
Self-Cleaning Effect
Fanggs teeth have a self-cleaning effect that lets
dirt flow between the teeth. The moldboardshaped sidewalls decrease friction and soil
compaction.
Wear Characteristics
Wear characteristics are relative to your
application and the material you are working in.
But there are many instances where the wear
differential of Fanggs teeth is more - lots more than conventional teeth.
Soil Bin Test
A soil bin test was performed using a Fanggs
tooth and a standard tooth.
Teeth were assembled to run one at a time
completely submerged through identically
compacted soil. Tests were run at a constant
1/2 mph.
Soil Bin Test Results
Standard Tooth
Fanggs Tooth
Additional Force Required
with Standard Tooth
Force Required
101.5 pounds
78.5 pounds
23.0 pounds
23.0 pounds divided by 101.5 pounds =
nearly 22.7% less effort required with the Fanggs tooth!
The standard tooth required 101.5 pounds of
force while the Fanggs tooth required only 78.5
pounds of force to transverse the same soil. The
Fanggs tooth required nearly 22.7% less effort
to do the same work!
Vertical Force
There was also a significant difference noted in the vertical force between the standard tooth
and Fanggs. The standard tooth showed a 4.7 pound force trying to plane up out of the soil.
The Fanggs tooth had a 5.0 pound force trying to go deeper. So while requiring nearly 23% less
effort to traverse the same soil, the Fanggs tooth was trying to work harder.
Fanggs/John Deere
2
Two Types of Fanggs
There are two basic designs of the Fanggs teeth: one is for digging, the other for loading.
Digging Tooth
Loading Tooth
Each tooth is designed to provide optimum performance by filling the bucket faster and requiring
less force. Material flow during operation is smooth and consistent on both the top and side
surfaces.
Operation Comparisons
Let’s take a look at comparisons of Fanggs and conventional teeth during various operations.
Conventional Tooth
Fanggs Tooth
Conventional Tooth
Fanggs Tooth
Loading
Digging
A conventional tooth uses a wedging
action to penetrate material.
A ski-nose pattern appears on
conventional loader teeth.
A Fanggs tooth slices through material
for more productivity and less effort.
The Fanggs design creates a level bucket
wear pattern.
Crowding
Conventional teeth rake material away from walls.
Fanggs teeth peel material away from walls.
Fanggs/John Deere
3
Part No. Explanation
Various information can be determined from the part number system. Refer to the following chart
for basic part numbering information.
Part Number Explanation for John Deere Fanggs
Prefix
Suffix
Explanation
TF
D
Fanggs Digging
TF
L
Fanggs Loading
Operator Tips
With conventional teeth, many operators start by raking the earth. It is a fast way to open the land,
but it can wear out a set of teeth very quickly.
The unique slicing action of Fanggs teeth make raking unnecessary. You can start digging
immediately. Here’s how:
3
2
1
1. Start with a steep angle of entry as shown above.
2. Keep the bucket at a flatter attitude as you continue to dig.
3. Maintain this flat profile, then curl the bucket as you complete the dig cycle.
This technique allows you to do the job faster and requires less power. It also helps maintain the
natural compaction of the soil while reducing the chance of undercutting.
Fanggs/John Deere
4
Fanggs/John Deere
Retention and Installation
Horizontal Pin and Split Washer
Spring Pin
Replacement teeth for both John Deere and
Caterpillar are retained with a horizontal pin
and split washer. This 2-piece retention method
makes tooth removal and installation fast and
easy. Both the pin and washer are reusable.
The spring pin is an economical means of
retaining teeth. The spring in the pin takes up
manufacturing tolerances and keeps the tooth
tight against the adapter.
When removing spring pins from John Deere
teeth, use special tool JDG97 (see Special Tools
below).
Flex Pin
Special Tools
When removing spring pins from John Deere
teeth, use special tool JDG97.
When removing flex pins from backhoe and
excavator teeth, use special tool D05339ST.
These tools are available from SERVICEGARD.
The flex pin is designed to withstand shock
and take up small amounts of adapter wear to
provide the necessary tight fit. The pin should
be installed so the half groove faces forward
towards the tooth tip. The groove is the
locking mechanism.
Pin Master® is also available and boasts of 3
minute removal and replacement time for an
entire set of 23 Series backhoe teeth. Order
TY15994 through your normal parts system.
Flex pins are reusable when properly
removed. Use special tool D05339ST when
removing flex pins from backhoe and
excavator teeth – see “Special Tools.”
Do not use bolts in place of flex pins when
installing teeth. Bolts create wear on pin holes
and promote tooth breakage. If teeth do not
stay on, there is probably an adapter problem.
Pin Master® Tooth Replacement Tool
(TY15994)
Fanggs/John Deere
5
John Deere
TF__D (Digging)
TF__L (Loading)
Non-Centerline
Fanggs Digging and Loading Teeth
• For general-purpose to heavy-duty digging conditions.
• Fanggs digging teeth have a curved shape and track the path of the bucket.
• Fanggs loading teeth have a flat bottom for improved bucket control.
-A-
-B-
-C-
Width
Point
Series
Tooth Part No.
Length
Cat 20 Series
TF1U3202 (Digging)
5-7/8″
Cat 25 Series
TF1U3252D (Digging)
7-5/8″
Retainer
Washer
Retainer
Washer
Retainer
Washer
TF1U3202P
T4T0001
T9J2258
T3G9609
PM8E6258
PM8E6259
Cat 25 Series
TF1U3252L (Loading)
Retainer
Washer
Retainer
Washer
T9J2258
T3G9609
Cat 30 Series
Retainer
Washer
T9J2308
T3G9609
-EPocket
Height
1-3/4″
1/8″
1-13/16″
1-5/8″
ADI
4.1 lb.
Cat: 416, 426, 428, 436; Competitive: Equipment with
Cat 20 Series-type adapters.
2-1/2″
1/8″
2-11/16″
2″
Cast
9.0 lb.
Cat: 205, 206, 211, 212, 213B, 214B, 613, E110,
E120B, E200, EL200; Competitive: Equipment with Cat
25 Series-type adapters.
7-5/8″
2-1/2″
1/8″
2-11/16″
2″
Cast
9.0 lb.
JD: 544E, 544G, 624E, 624G, 644H; Cat: 613, 916,
920, 924F, 926, 930, 936, 938F, 939, 941, 941B, 943,
943GLP, 951, 951C, 953, 953GLP, IT12, IT24, IT28;
Competitive: Equipment with Cat 25 Series-type
adapters.
TF1U3302D (Digging)
9″
3″
1/8″
3″
2-1/2″
ADI
12.3 lb.
JD: 690E; Cat: 205, 206, 211, 212, 213B, 214B,
215, 219, 224, 235, E180, E200, EL200; Competitive:
Equipment with Cat 30 Series-type adapters.
TF1U3302L (Loading)
8-3/4″
3″
T9J2308
T3G9609
Cat 30 Series
Retainer
Washer
PM8E6258
PM8E6259
-DPocket
Width
1/4″
3″
2-1/2″
Cast
13.3 lb.
JD: 644E, 644G, 644H; Cat: 950, 950B, 955, 966,
966C; Competitive: Equipment with Cat 30 Series-type
adapters.
Fanggs/John Deere
12
John Deere
Fanggs Digging and Loading Teeth (Continued)
Series
Tooth Part No.
Cat 35 Series
TF1U3352D (Digging)
Retainer
Washer
Retainer
Washer
T9J2358
T3G9549
T8E6358
T8E6359
Cat 45 Series
TF9W8452D (Digging)
Retainer
Washer
Retainer
Washer
T1U1458
T3G9549
PM8E0468
PM8E8469
-A-
-B-
-C-
Length
Width
Point
Pin
3-3/8″
4-3/4″
3-1/4″
2-15/16″
Cast
16.9 lb.
JD: 790D, 790E, 892D, 892E; Cat: 205, 206, 211,
212, 213B, 214B, 224, 225, 229, 231, 245, E240, E248;
adapters.
10″
3-3/8″
4-3/4″
3-7/8″
3-7/8″
Cast
28.5 lb.
JD: 790D, 790E, 892D, 892E, 992, 992D; Cat: 224,
225, 229, 235, 325, 330, 375, E240, E248, E300;
adapters.
Pin
TF23D (Digging)
1-3/4″
1/8″
1-1/2″
1-5/8″
ADI
3.8 lb.
JD: Buckets with H & L 23 Series adapters (5/8″ or
3/4″ edge); Case: 480F, 580K, 590, 680L, 780D;
Ford: 555D, 575D, 655D, 755B, 710D; Competitive:
Backhoes with H & L 23 Series-type adapters (5/8″ or
3/4″ edge).
TF23L (Loading)
5-7/8″
TF252 (Digging)
7-1/2″
TF23P
H & L 25 Series
Pin
Loading
TF23P
H & L 23 Series
TF25P
-EPocket
Height
10″
Digging
H & L 23 Series
-DPocket
Width
6″
1-3/4″
1/4″
1-1/2″
1-5/8″
ADI
3.3 lb.
JD: Backhoe loading buckets with H & L 23 Seriestype adapters; Skid-Steer: JD14, JD24, JD24-A; Case:
480F, 580K, 580L, 590, 590L, 680L, 780D; Ford:
555D, 575D, 655D, 755B.
2-1/2″
1/8″
2-1/16″
2-1/8″
ADI
8.8 lb.
JD: 690, 690A, 690B, 690C, 690D, 690E;
Competitive: Excavators with H & L 25 Series-type
adapters (1-1/2″ edges).
Fanggs/John Deere
13
John Deere
-A-
-B-
-C-
Length
Width
Point
-DPocket
Width
-EPocket
Height
Series
Tooth Part No.
Hensley 156 Series
TF156 (Digging)
1-3/4″
1/8″
1-5/8″
1-5/8″
ADI
3.9 lb.
JD: 300D, 310D, 315D, 410D, 500B, 510, 510D, 710B;
Competitive: Backhoes with Hensley 156 Series-type
adapters (1″ edges).
TF160 (Digging)
6-1/4″
TF220 (Digging)
7″
2-5/8″
1/4″
2-1/4″
2-1/8″
Cast
6.0 lb.
JD: 490, 490D, 490E, 495D, 590D, 595, 595D;
Competitive: Backhoes and excavators with Hensley
220 Series-type adapters (1-1/4″ edges).
TF290 (Digging)
8-1/4″
TF310 (Digging)
7-1/2″
TF330 (Digging)
9-1/4″
TF350 (Digging)
10-5/8″
Pin
TF13P
Hensley 160 Series
Pin
TP160
Hensley 220 Series
Pin
TP160
Hensley 290 Series
Pin
TK290
Hensley 310 Series
Pin
TP160L
Hensley 330 Series
Pin
TK330
Hensley 350 Series
Pin
TP400HD
6″
2-1/8″
1/8″
1-5/8″
2-3/8″
Cast
4.2 lb.
JD: 190E, 290D; Competitive: Backhoes and
excavators with Hensley 160 Series-type adapters
(1″ edges).
3-1/4″
1/4″
2-7/8″
2-11/16″
Cast
10.4 lb.
JD: 490, 490D, 490E, 495D, 590D, 595, 595D, 690,
690A, 690B, 690C, 690D, 690E; Competitive:
Excavators with Hensley 290 Series-type adapters
(1-1/2″ edges).
3-1/4″
1/4″
3″
2-1/8″
Cast
10.4 lb.
JD: 590D, 595, 595D, 690, 690A, 690B, 690C, 690D,
690E, 790, 790D, 790E, 792, 792D; Competitive:
(1-1/2″ edges).
3-5/8″
1/4″
3-13/32″
3-3/16″
Cast
15.3 lb.
JD: 590D, 595, 595D, 690, 690A, 690B, 690C, 690D,
690E, 790, 790D, 790E, 792, 792D; Competitive:
(1-1/2″ edges).
4-1/4″
1/4″
3-1/2″
2-7/8″
Cast
23.6 lb.
Competitive: Excavators with Hensley 350 Series-type
adapters.
Fanggs/John Deere
14
John Deere
-A-
-B-
-C-
Width
Point
Series
Tooth Part No.
Length
Hensley 400 Series
TF400 (Digging)
9-1/4″
TF475 (Digging)
11-7/8″
Pin
TP400HD
Hensley 475 Series
Pin
TP475
5-3/4″ 1/4″
4-3/4″ 3-1/2″
Cast
40.7 lb.
JD: 890, 890A, 892D, 892E, 992D, 992E;
adapters (2-1/2″ edges).
Reference 2
John Deere
TF13 (Loading)
Pin
Ref. 2
John Deere
TF10L (Loading)
Pin
Washer
Ref. 1
TF10P
T112196
John Deere
TF11L (Loading)
Pin
Ref. 1
TP160L
John Deere
TF33L (Loading)
Pin
Washer
Ref. 1
T67083
T67086
-EPocket
Height
4-1/2″ 1/4″
4″
2-7/8″
Cast
19.7 lb.
JD: 690, 690A, 690B, 690C, 690D, 690E, 790, 790D,
790E, 792, 792D, 890, 890A, 892D, 892E, 992D, 992E;
adapters (2″ edges).
Reference 1
TF13P
-DPocket
Width
6-3/8″
2-5/8″
1/8″
1-1/2″
1-1/8″
ADI
3.9 lb.
Crawler Loaders: 1010, 2010, 350, 350A, 350B,
350C, 355D; Wheel Loaders: 310, 400, 401A, 401C,
410, 410B, 415B, 500, 500A, 500C, 510B, 515B, 610B,
710B, 710C, 710E
5-1/2″
3-5/8″
1/8″
ADI
6.1 lb.
4-Wheel Drive Loaders: 544E, 544G, 544H, 624E,
624G, 644E, 644G; Crawler Loaders: 455G, 555G
3-5/8″
1/8″
2−3/8″
1−3/4″
ADI
5.1 lb.
4-Wheel Drive Loaders: 444, 444C, 444CH, 444D,
544, 544A, 544B, 544C, 544D, 644, 644A, 644B, 644C,
644D; Compactors: 646, 646B, 646C; Crawler
Loaders: 450, 450B, 450C, 455D, 455E, 555, 555A,
555B, 655, 755, 755A
6″
3-1/4″
1/8″
2−1/2″
3−1/8″
Cast
15.0 lb.
4-Wheel Drive Loaders: 744E, 744H, 844;
Crawler Loaders: 655, 655B, 755, 755A, 755B
9-5/8″
Fanggs/John Deere
15
John Deere
Series
Pin
Washer
Pin
Washer
Chisel Teeth
-A-
-B-
-C-
Tooth Part No.
Length
Width
Point
T105690
5-7/8″
2″
T69647
9-1/8″
T112195
T112196
T67083
T67086
-DPocket
Width
-EPocket
Height
3/8″
2-1/4″
1-3/4″
Cast
4.7 lb.
2-5/8″
1/4″
2-1/2″
3″
Cast
10.5 lb.
4-Wheel Drive Loaders: 744E, 744H, 844;
Crawler Loaders: 655, 655B, 755, 755A, 755B, 855
Fanggs/John Deere
16
John Deere
Standard Teeth
Reference 1
Reference 2
Series
Tooth Part No.
John Deere
T103189
Pin
Washer
T112195
T112196
John Deere
Pin
Pin
John Deere
Pin
Washer
T29887
T56004
John Deere
T79008
John Deere
Pin
TH106698
John Deere
Pin
TP160
Point
-EPocket
Height
3-11/16″
3/16″
2-1/4″
1-3/4″
Cast
5.9 lb.
2-13/16″
1/4″
2-3/8″
1-3/4″
Cast
5.0 lb.
544, 544A, 544B, 544C, 544D, 644, 644A, 644B, 644C,
644D; Compactors: 646, 646B, 646C; Crawler
Loaders: 655, 755, 755A
4-5/8″
7/16″
Cast
4-Wheel Drive Loaders: 844
3-3/16″
2-1/4″
13.1 lb.
4-1/8″
3/16″
2-1/2″
3″
Cast
14.0 lb.
4-Wheel Drive Loaders: 744E, 744H, 844
5-1/2″
2
U13449
34M7070
Width
-DPocket
Width
9-1/8″
1
Wedge Pin TH106699
Lock
TH106700
Length
8″
1
T67083
T67086
-C-
5-3/4″
1
T56005
-B-
5-9/16″
1
TP160
John Deere
Ref.
-A-
2-1/4″
3/16″
Cast
Excavators: 70, 70D
1-7/8″
1-7/8″
3.1 lb.
4-5/16″
1
U16086
2-5/8″
3/16″
1-1/2″
1-1/8″
Cast
2.2 lb.
Crawler Loaders: 1010, 2010, 350, 350A, 350B,
350C, 355D; Wheel Loaders: 310, 400, 401A, 401C,
410, 410B, 415B, 500, 500A, 500C, 510B, 515B, 610B,
710B, 710C, 710E
5-3/8″
1
3-5/8″
5/16″
2-3/8″
1-3/4″
Cast
4.5 lb.
544, 544A, 544B, 544C, 544D, 644, 644A, 644B, 644C,
644D; Crawler Loaders; 450, 450B, 450C, 455D,
455E, 555, 555A, 555B; Scraper Bowls: 760, 760A,
762, 762A, 762B, 860, 860A, 860B, 862, 862B
Fanggs/John Deere
17
John Deere
Reference 1
Standard Bolt-On Teeth
Reference 2
Reference 3
-ALength
Series
Tooth Part No.
John Deere
AT121474
Ref.
Center
John Deere
John Deere
John Deere
T110052
John Deere
T110058
John Deere
T111297
-DHole
Spacing
-EWt.
12-3/4″
2″
3/16″
2-5/8″
7-1/4″
23˚
4″
JD: 344E, 344H, 444E
15/16″
9.9 lb.
4
12-3/4″
2-3/8″
1/4″
2-5/8″
7-1/4″
23˚
4″
JD: 344E, 344H, 444E
15/16″
13.7 lb.
4
12-3/4″
2-3/8″
1/4″
2-5/8″
7-1/4″
23˚
3-7/8″
JD: 344E, 344H, 444E
15/16″
14.0 lb.
2
9-1/2″
2-3/8″
JD: 50
1-5/8″
1/4″
4-7/8″
1-3/4″
11/16″
5.7 lb.
2
8-1/4″
2″
JD: 30
1-3/8″
1/4″
3-3/4″
1-3/4″
5/8″
3.9 lb.
8″
1-1/4″
1/4″
9/16″
3.5 lb.
2-1/2″
60˚
1/4″
5-1/4″
3-1/2″
AT121476
Corner, Left-Hand
-G-
-CPoint
3
AT121475
Corner, Right-Hand
-F-
-BWidth
Reference 4
2
4″
JD: 15
John Deere
T115680
1
9-3/4″
2-1/2″
JD: 84
Fanggs/John Deere
18
5/8″
6.1 lb.
John Deere
Adapters
Reference 1
Reference 2
Reference 3
Reference 4
Reference 5
Reference 6
Reference 7
Fanggs/John Deere
19
John Deere
Adapters
Note: John Deere adapter and teeth applications are listed on pages 10-11.
Adapter
Part No.
Type
Attachment
B
C
D
Hole
Spacing
Wt.
(lb.)
T103190
Bolt-On
Center
1
7-3/4″
1-1/4″
4-3/4″
30˚
4-13/16″
14.4
T103191
Bolt-On
Corner
2
8-1/4″
1-1/4″
1-3/4″
30˚
T104673
Bolt-On
Center
3
7-7/16″
1-5/16″
8-15/16″
30˚
4-11/16″
27.0
T104674
Bolt-On
End
2
8-15/6″
1-1/4″
2-3/4″
30˚
4-13/16″
33.6
T105692
Bolt-On
Center
1
5-5/8″
1″
3-5/8″
30˚
3-5/8″
10.6
T112163
Bolt-On
Corner
2
5-5/8″
1″
1-5/8″
30˚
T112164
Bolt-On
Center
1
5-7/8″
3/4″
4″
30˚
3-5/8″
9.5
T123077
Bolt-On
Center
3
9-1/4″
1-1/2″
10-1/2″
30˚
5-3/16″
40.4
T29886
Bolt-On
1
8-1/4″
1-3/8″
4″
30˚
6″
12.6
T35385
Bolt-On
1
8-5/8″
1-1/2″
5-7/16″
32˚
5-1/4″
14.7
T38783
Bolt-On
5
8-3/8″
1-1/8″
9-7/8″
30˚
2″
12.3
T56003
Bolt-On
3
8-1/4″
1-15/16″
10-1/2″
30˚
5″
36.7
T79004
Bolt-On
Center
3
8-9/16″
1-13/16″
11-1/4″
30˚
5-3/16″
38.2
T79006
Bolt-On
Corner
2
11-13/16″
1-1/2″
2-3/8″
30˚
57.2
TH106697
Weld-On
7
1-7/8″
15/16″
5-1/4″
30˚
6.6
Ref.
A
Fanggs/John Deere
20
23.2
14.2
John Deere
Adapter
Part No.
Adapters (Continued)
Type
Attachment
Ref.
B
C
D
Hole
Spacing
Wt.
(lb.)
U16087
Bolt-On
6
7-1/2″
1-1/2″
8-1/8″
35˚
2″
9.3
U16864
Bolt-On
1
8-5/8″
1-1/8″
3-7/8″
32˚
6-1/2″
10.3
U41344
Bolt-On
1
4-7/16″
1-1/8″
3-3/8″
30˚
2-3/8″
5.2
A
Adapter Hardware
Adapter
Bolt Size
Bolt
Nut
Washer
T103190
1″ x 3-1/8″
19M7287
14M7278
24M7243
T103191
1″ x 3-1/2″
19M8288
14M7278
24M7243
T104673
1″ x 4-1/4″
19H3556
K40018
T75690
T104674
1-1/4″ x 4-1/4″
19H3594
A20329
T81065
T105692
3/4″ x 2-1/2″
19M8102
14M7277
24M7242
T112163
1″ x 3-1/2″
19M8288
14M7278
24M7243
T112164
3/4″ x 2-1/2″
19M8102
14M7277
24M7242
T123077
1-1/4″ x 5″
08H4815
A20329
T79096
T29886
5/8″ x 3-1/4″
19H2072
K40015
24H1367
T35385
3/4″ x 2-1/4″
19H1782
K40016
24H1400
T38783
3/4″ x 4″
T70287
14H1046
T83426
T56003
7/8″
–
_
_
T79004
1-1/4″
–
–
–
T79006
1-1/4″ x 4-1/2″
08H4814
A20329
T79096
U16087
3/4″ x 4″
T70287
14H1046
12H236
U16864
5/8″ x 3-1/4″
10H1157
K40015
24H1367
Fanggs/John Deere
21
John Deere Hardware
Illustrated parts are actual size.
TF10P
T112196
T112195
TT9J2308
T3G9609
TH106700
TH106699
Fanggs/John Deere
22
John Deere Hardware
34M7070
TF13P
TP160
TP160L
T56005
Fanggs/John Deere
23
John Deere Replacement Teeth for Caterpillar Products
Oversized Pocket and Extended Adapter
Nose Piece
The John Deere replacement teeth for
Caterpillar products come in sizes and
types to fit almost all machine makes and
models. The oversized pocket
characteristics of these teeth with the
extended adapter nose piece provide a nose
fit between the tooth and adapter which
results in strong impact resistance but a
loose fit in the ramps.
Pin and Washer Retention
Replacement teeth for Caterpillar
equipment use a 2-piece retention method
which makes tooth removal and installation
fast and easy. Both the pin and the washer
are reusable. The original style and "E"
style are now available.
Original Style Pins and Washers
The original retention for replacement
Caterpillar teeth use a horizontal pin and
split washer.
Do not use the new "E" washers with the
original style pins.
"E" Pins and Washers
Centerline Design, Oversized Pocket .
Nose fit provides impact resistance with loose pin
and ramp fit.
"E" Pins and Washers have an "E" in the Part No.
The shallow radius groove on the "E" pin
reduces the spread which increases locking
force.
The tapered pin outer edge reduces contact
with the inside of the adapter counterbore.
This minimizes breakage.
The new pin jacket on the washer aligns the
pin and washer during installation.
Do not use split washers with "E" washers
with "E" pins. "E" pins and washers are
interchangeable with original pins/washers
in all sizes except J450/J460 adapters.
Original pins/washers fit J450 adapters.
"E" pins/washers fit J460 adapters
John Deere Replacement Teeth for Caterpillar Products
Various information can be determined from the part numbering system. Refer to the
following chart for basic part number information.
Part Number Explanation (Replacement Teeth for Caterpillar Products)
P r e f i x and S u f f I x
Explanation
NOTES:
PM or T
0
Flare
PM or T
1
Short
The "Series" equipment the
PM or T
2
Long
tooth is used on is generally
PM or T
2
Heavy Duty Long
provided in the part number.
PM or T
3
Abrasion
PM or T
9
Penetration
"N" within the part number
PM or TT
T
Tiger
designates heavy-duty.
PM or TX
WT
Twin Tiger
TF
D
Fanggs Digging
See examples below.
TF
L
Fanggs Loading
PM
SYL
Ribbed Sharp
PM
RC
Rock Chisel
PM
RP
Rock Penetrator
Examples:
T3G8250
Flare Tooth used with 25 Series Adapters (T3G8250)
T9N4252
Long (Heavy-Duty) used with 25 Series Adapters (T9N4252)
T9N4353
Abrasion Tooth used with 35 Series Adapters (T9N4353)
T1U3551
Short Tooth used with 55 Series Adapters (T1U3551)
TF1U3252D
Fanggs Digging used with 25 Series Adapters (TF1U3252D)
John Deere Replacement Teeth for Caterpillar Products - Types Available
•
•
Fanggs Digging Teeth
(Non-Centerline)
TF_D Part Numbers
For general-purpose to
heavy-duty digging
conditions.
Provide a clean start and
close crowd.
•
•
Fanggs Loading Teeth
(Non-Centerline)
TF_L part Numbers
heavy-duty digging
conditions.
Flat bottom for improved
bucket control.
•
•
•
Short Teeth
(Centerline)
PM or T_1 Part Numbers
Designed for use in highimpact and pry-out work.
Provides more strength but
less wear than the long tooth
Long Teeth
(Centerline)
For loading and digging
Tiger Teeth
(Non-Centerline)
PM or TT_T Part Numbers
• Long, aggressive teeth
designed for breaking
extremely tight soil.
• Used primarily as center
teeth
Penetrator Teeth
(Non-Centerline)
• Use in highly compacted,
dense material such as clay.
• Center rib provides added
strength.
• Maintains good sharpness
throughout its life.
Twin Tiger Teeth
(Non-Centerline)
PM or TX_WT Part Numbers
• For densely compacted
material.
• Use primarily as a corner
tooth but can be used in
center.
Abrasion Teeth (Standard and
Heavy-Duty)
(Non-Centerline)
• Use where extended tip life
is needed in highly-abrasive
conditions.
• Heavy-duty teeth have more
wear material than the
standard teeth.
•
•
•
•
Flare Teeth
(Centerline)
Work extremely well in
loose and mud-like
conditions.
Ribbed Sharp
(Centerline)
PM _SYL Part Numbers
Excellent Penetration
Greater Wearlife than tiger
For digging in tight or
compacted material
•
•
Rock Chisel
(Non-Centerline)
PM _RC Part Numbers
Extremely abrasive terrain
requiring extra penetration.
Increased Wear Material
•
Rock Penetrator
(Non-Centerline)
PM _RP Part Numbers
Loaders in high abrasion
quarry and mining
operations.
.
•
•
H.D. Long
(Non-Centerline)
Use in high abrasion
application
Added wear material in tip
for longer wear life.
Replacement for Caterpillar Products
Illustrated parts are actual size
Retainers
T8E6208
T8E6209
20 Series Fanggs
TF1U3202P
T4T0001
20 Series except Fanggs
Retainers (Continued)
T6Y3228
22 Series
T8E6259
22, 25 Series
T9J2258
25 Series
T8E6258
25 Series
T3G9609
25, 30 Series
T9J2308
30 Series
T7T3409
40 Series
T7T3408
40 Series
T9J2358
35 Series
T8E6359
35 Series
T8E6358
35 Series
T3G9549
35 Series
T3G9549
35, 45 Series
T1U1458
45 Series
(J450 Adapters)
T8E8469
45 Series
T8E0468
45 Series
(J460 Adapters)
T3G9559
55 Series
T1U1558
55 Series
Caterpillar - Tooth by Series
a
20 Series
g
m
d
j
a
f
-
a
Fanggs dig
long
tiger
twin tiger
abrasion
penetrator
org pin
org wash
e type pin
e type wash
adapter
adapter
TF1U3202
T1U3202
TT1U3202
TX1U320WT
T4T2203
T1U3209
TF1U3202P
T4T0001
T8E6208
T8E6209*
PM4T1204
T8J7525
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
Cat flush weld-on: 416, 910, 931
Cat center weld-on bottom strap: 416, 426, 428, 436, 438, 910, 914G,
931, 935
22 Series
style
m
-
description
long
e type pin
e type wash
adapter
part no.
T6Y3222
T6Y3228
T8E6259
PM6Y3224
disc. used on
ü
ü
ü
ü Cat weld-on double strap: 446, 933, 307, 307B
Caterpillar - Applications
25 Series
style
g
c
h
m
d
k
j
l
f
e
a
b
-
description
Fanggs dig
Fanggs load
short
long
long h-d
tiger
twin tiger
flare
penetrator
abrasion h-d
abrasion
ribbed sharp
org pin
org wash
e type pin
e type wash
adapter
adapter
adapter
part no.
TF1U3252D
TF1U3252L
T1U3251
T1U3252
T9N4252
TT1U3252
TX1U3252WT
T3G8250
T9J4259
PM9N4253
T4T2253
PM1U3252SYL
T9J2258
T3G9609
T8E6258
T8E6259
T25CA
T25EA
T1U1254
disc.
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
used on
-
adapter
T3G0169
ü
Cat center weld-on: 205, 206, 211, 212, 213B, 214B, 916, 920, 926, 930,
936, 941, 941B, 951, 951C, 953, 953B, 953C
-
adapter
T1U0257
ü
Cat center bolt-on: 916, 920, 924F, 926, 928, 930, 936, 938F, 938G, 939,
941, 941B, 943, 943LPG, 951, 951C, 953, 953B, 953C
-
adapter
PM3G4258
ü
Cat left bolt-on: 916, 920, 924F, 926, 928, 930, 936, 938F, 938G, 939,
941, 941B, 943, 943LPG, 951, 951C, 953, 953B, 953C
-
adapter
PM3G4259
ü
Cat right bolt-on: 916, 920, 924F, 926, 928, 930, 936, 938F, 938G, 939,
941, 941B, 943, 943LPG, 951, 951C, 953, 953B, 953C
-
adapter
PM6Y3254
ü
Cat center weld-on: 311, 312, 311B, 312B, 312BL
J D center bolt-on: 544E, 544G, 544H, 624E, 624G, 624H
J D center bolt-on: 544E, 544G, 544H, 624E, 624G, 624H
Cat flush weld-on: 205, 206, 211, 212, 213B, 214B, 918F, 920, 926, 928,
936, 953, 951, 953B, 953C
30 Series
style
g
c
h
m
d
k
j
l
f
e
a
b
n
-
description
Fanggs dig
part no.
TF1U3302D
disc. used on
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
-
Fanggs load
short
long
long h-d
tiger
twin tiger
flare
penetrator
abrasion h-d
abrasion
ribbed sharp
rock chisel
org pin
org wash
adapter
adapter
adapter
TF1U3302L
T1U3301
T1U3302
T9N4302
TT1U3302
TX1U3302WT
T107-3300
T9J4309
T9N4303
T4T2303
PM1U3302SYL
PM1U3302RC
T9J2308
T3G9609
T30CA
T30EA
T3G6304
-
adapter
adapter
adapter
T1U0307
PM3G4308
PM3G4309
ü
ü
ü
-
adapter
adapter
adapter
adapter
adapter
T4T4307
PM3G9307
PM3G8308
PM3G8309
PM1U1304
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
JD center bolt-on: 644E, 644G, 644H,
JD end bolt-on: 644E, 644G, 644H,
JD double strap center: 690E, Cat double strap center: 215, 219, 315,
315B, 315BL, 320, 320B
Cat center bolt-on: 944, 950, 953B, 955
Cat 1 - 1-1/4" edge left bolt-on: 950B, 955, 960F, 963
Cat 1 - 1-1/4" edge right bolt-on: 950B, 950E, 950F, 950G 955, 960F,
962G, 963
Cat center bolt-on: 950, 953B, 955, 960F, 963
Cat center bolt-on: 966, 966C,
Cat 1-1/4" edge left bolt-on : 962G, 966, 966C
Cat 1-1/4" edge right bolt-on : 962G, 966, 966C
Cat flush weld-on: 944, 950, 955, 966
35 Series
style
g
h
m
d
k
j
l
f
e
a
b
n
I
-
description
Fanggs dig
part no.
TF1U3352D
disc. used on
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
short
long
long h-d
tiger
twin tiger
flare
penetrator
abrasion h-d
abrasion
ribbed sharp
rock chisel
rk penetrator
org pin
org wash
e type pin
e type wash
adapter
T1U3351
T1U3352
T9N4352
TT1U3352
TX1U3352WT
T107-3350
T9J4359
T9N4353
T4T2353
PM1U3352SYL
PM1U3352RC
PM4T2353RP
T9J2358
T3G9549
T8E6358
T8E6359
T3G8354
-
adapter
PM1U1354
ü
Cat flush weld-on: 245, 950, 950B, 963B, 966C, 966D, 966E, 966F, 973,
973LPG, 977, 977L, 980, 980B
-
adapter
adapter
PM8J5357
T3G3357
ü
ü
Cat center bolt-on: 963, 966
-
adapter
PM3G5358
ü
Cat cornergaurd LH: 960F, 966, 966D, 966E, 966F, 970, 970F, 973,
973LPG, 977, 977L,
-
adapter
PM3G5359
ü
Cat cornergaurd RH:960F, 966, 966D, 966E, 966F, 970, 970F, 973,
973LPG, 977, 977L,
-
adapter
adapter
adapter
adapter
PM8J3357
PM1U1357
PM1U1350
PM9J2357
ü
ü
ü
ü
ü
ü
ü
ü
ü
JD double strap center: 790D, 892D, 892E, Cat double strap center: 215,
219, 225, 229, M318, 320, 320B, 320BL, 322, 322B, 322BL, 325BL, 325B,
325
Cat center bolt-on: 960F, 966, 966D, 966E, 966F, 970, 970F, 973,
973LPG, 977, 977L
Cat Center Bolt-on: 980C, 980F
Cat Center Bolt-on: Spade Nose 980C
40 Series
style
m
d
f
f
n
-
description
long
long h-d
penetrator
penetrator
rock chisel
org pin
org wash
e type wash
adapter
part no.
T7T3402
T8E4402
T6Y7409
PM6Y7409
PM7T3402RC
T7T3408
T7T3409
T8E8409
PM7T3404
disc. used on
ü
ü
ü
ü
ü
ü
ü
ü
Cat double strap center: 320L, 325L, 330L, 322L, 330BL, 345B, 345BL,
320BL, 322BL, 325BL, 320B, 322B, 325B, 330B, 320, 322, 325, 330
45 Series
style
g
h
m
d
k
j
l
f
a
e
b
n
I
-
description
Fanggs dig
part no.
TF9W8452D
disc. used on
ü
ü
ü
ü
T9W8451
T9W8452
T9N4452
PM1U3452T
PM1U3452WT
T107-3450
T9W8459
PM9W1453
T9N4453
PM9W8452SYL
PM1U3452RC
PM9W1453RP
T1U1458
T3G9549
T8E0468*
T8E8469*
T1U1454
-
short
long
long h-d
tiger
twin tiger
flare
penetrator
abrasion
abrasion h-d
ribbed sharp
rock chisel
rk penetrator
org pin
org wash
e type pin
e type wash
adapter
adapter
T8E6464**
ü
Cat double strap center: 229, 235, 330, 330B, 330BL, 345, 345BL, 350,
350L
-
adapter
PM8E3464**
ü
Cat spade nose double strap center weld-on: 973SLAG, 983, 988, 988B
-
adapter
PM8E3465**
ü Cat spade nose double strap RH: 983, 988, 988B
adapter
PM8E3466**
ü Cat spade nose double strap LH: 983, 988, 988B
adapter
PM8J1454
ü
adapter
PM9J9584
ü Cat flush mount weld-on:
Note: All 45 Series adapter will not accept e-type pins and retainers
* used on J460 adapters only
** J460 adapter
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
JD double strap center: 790D, 790E, 892D, 892E, 992, 992D
55 Series
style
h
m
d
f
e
n
I
-
description
short
long
long h-d
penetrator
abrasion h-d
rock chisel
rk penetrator
org pin
org wash
e type pin
e type retainer
adapter
adapter
adapter
adapter
part no.
T1U3551
T1U3552
PM9N4552
T9J4559
PM6Y2553
PM1U3552RC
PM9W1553RP
T1U1558
T3G9559
T6Y8558
T8E5559
PM1U1553
PM3G9494
PM3G9495
PM3G9496
disc. used on
ü
ü
ü
ü
ü
part no.
T4T4702
PM4T4703
T4T4707
T9U9616
T4T4704
disc. used on
ü
ü
ü
ü
ü
Cat double strap: 375, 375L, 375LME, Deere double strap: 550LC, 750
ü
ü
ü
ü
ü
ü
ü
ü
Cat double strap: 245, 345, 345B, 345BL, 350, 350L, 375
Cat double strap center: 245FS
Cat double strap RH: 245S
Cat double strap LH: 245S
70 Series
style
m
a
-
description
long
abrasion
washer
pin
adapter
CATERPILLAR LOADER TIPS
VERTICAL-PIN STYLE (OLD STYLE)
MODEL NO.
SHORT TIP
920, 922, 930, 931,
933, 941, 944
LONG TIP
PIN
LOCK
PM4K6936
PM4K0043
PM4K0041
930, 944, 950, 951,
955, 966
PM5K2925
PM4K0034
PM4K0043
PM4K0041
950, 966, 977, 980
PM5K2926
PM4K6148
PM4K0032
PM4K0008
Caterpillar - Specifications
T
20 Series
style
T
T
T
T
T
T
2
3
description
Fanggs dig
long
tiger
twin tiger
abrasion
penetrator
adapter
adapter
part no.
TF1U3202
T1U3202
TT1U3202
TX1U320WT
T4T2203
T1U3209
PM4T1204
T8J7525
a
5-7/8"
5-11/16"
6-1/2"
6-1/2"
5-11/16"
5-11/16"
7-1/4"
3-15/16"
b
1-3/4"
2"
point
2-3/4"
2-3/16"
1"
1/2"
1"
c
1-13/32"
1-13/32"
1-13/32"
1-13/32"
1-13/32"
1-13/32"
1/2"
1"
d
1-27/32"
1-27/32"
1-27/32"
1-27/32"
1-27/32"
1-27/32"
23°
23°
lbs.
4.1
3
3.5
5.5
3
2.4
4.6
3.1
a
6-9/16"
5-9/16"
b
2-1/8"
3-11/16"
c
1-3/4"
1-1/16"
d
2-11/32"
22°
lbs.
3.7
6.6
22 Series
style description
part no.
T long
T6Y3222
1 adapter
PM6Y3224
25 Series
style
T
T
T
T
T
T
T
T
T
T
T
T
4
5
2
3
4
6
6
1
description
part no.
Fanggs dig
TF1U3252D
fanggs load
short
long
long h-d
tiger
twin tiger
flare
penetrator
abrasion
abrasion h-d
ribbed sharp
adapter
adapter
adapter
adapter
adapter
adapter
adapter
adapter
TF1U3252L
T1U3251
T1U3252
T9N4252
TT1U3252
TX1U3252WT
T3G8250
T9J4259
T4T2253
PM9N4253
PM1U3252SYL
T25CA
T25EA
T1U1254
T3G0169
T1U0257
PM3G4258
PM3G4259
PM6Y3254
a
7-5/8"
7-5/8"
b
2-1/2"
2-1/2"
c
1-15/16"
1-15/16"
d
2-11/16"
2-11/16"
6-11/16"
7-3/4"
8-1/8"
8-1/8"
8-1/8"
8"
7-1/2"
7-1/2"
7-15/16"
8-1/4"
5-5/8"
8-1/4"
9-1/4"
7-1/2"
2-3/4"
5-3/4"
5-3/4"
6-1/8"
2-1/4"
2-5/8"
2-2/1"
point
3-1/8"
4-1/2"
1-3/8"
3-1/8"
3-15/16"
2-3/4"
1"
1"
2"
2-5/16"
4-7/8"
4-3/16"
4-3/16"
5"
1-15/16"
1-15/16"
1-15/16"
1-15/16"
1-15/16"
1-15/16"
1-15/16"
1-15/16"
1-15/16"
1-15/16"
7-1/8"
3-1/8"
1"
2"
1-1/16"
1-1/16"
1-1/16"
1-5/16"
2-11/16"
2-11/16"
2-11/16"
2-11/16"
2-11/16"
2-11/16"
2-11/16"
2-11/16"
2-11/16"
2-11/16"
30°
30°
22°
22°
23°
43°
43°
22°
lbs.
9
9
5.9
5.9
10.9
5.5
7.3
8.5
5.3
7
10
6.2
14.2
18.6
12.1
10.8
18.2
25
25
9.5
30 Series
style
T
T
T
T
T
T
T
T
T
T
T
T
T
4
5
1
4
6
6
4
4
6
6
2
description
part no.
Fanggs dig
TF1U3302D
Fanggs load
short
long
long h-d
tiger
twin tiger
flare
penetrator
abrasion
abrasion h-d
ribbed sharp
rock chisel
adapter
adapter
adapter
adapter
adapter
adapter
adapter
adapter
adapter
adapter
adapter
TF1U3302L
T1U3301
T1U3302
T9N4302
TT1U3302
TX1U3302WT
T107-3300
T9J4309
T4T2303
T9N4303
PM1U3302SYL
PM1U3302RC
T30CA
T30EA
T3G6304
T1U0307
PM3G4308
PM3G4309
T4T4307
PM3G9307
PM3G8308
PM3G8309
PM1U1304
a
9"
8-3/4"
b
3"
3"
7-5/8"
8-3/4"
8-7/8"
9-3/8"
9-1/8"
8-1/2"
8-1/2"
8"
8-5/16"
9-1/4"
9-7/8"
2-5/16"
10"
7-7/8"
2-3/4"
7"
7"
3-3/16"
3-1/8"
8-3/16"
8-3/16"
9-1/4"
2-3/4"
2-3/4"
2-3/4"
3-1/4"
4"
6"
1-1/2"
3-7/16"
4-3/8"
3-1/2"
3-1/4"
4-13/16"
4-1/8"
4-3/8"
4-7/8"
4-3/4"
4-3/4"
6-1/2"
6-5/16"
5-1/2"
5-1/2"
3-3/4"
c
2-3/8"
2-3/8"
2-3/8"
2-3/8"
2-3/8"
2-3/8"
2-3/8"
2-3/8"
2-3/8"
2-3/8"
2-3/8"
2-3/8"
2-3/8"
d
3-1/32"
3-1/32"
3-1/32"
3-1/32"
3-1/32"
3-1/32"
3-1/32"
3-1/32"
3-1/32"
3-1/32"
3-1/32"
3-1/32"
3-1/32"
1-5/16"
1-1/16"
1-3/8"
1-1/16"
1-1/16"
1-1/16"
1-5/16"
1-5/16"
1-1/16"
1-1/16"
1-1/2"
30°
30°
22°
39°
39°
39°
23°
23°
39°
39°
23°
lbs.
12.3
13.3
9
9.9
12.1
9.2
10.7
11
7.8
10.8
16.7
10
11.8
20.8
21.7
16.3
23.1
34.9
34.9
31.2
31.9
36.5
36.5
18.3
35 Series
style
T
T
T
T
T
T
T
T
T
T
T
T
T
1
2
7
4
6
6
7
4
3
7
description
part no.
Fanggs dig
TF1U3352D
short
long
long h-d
tiger
twin tiger
flare
penetrator
abrasion
abrasion h-d
ribbed sharp
rock chisel
rk penetrator
adapter
adapter
adapter
adapter
adapter
adapter
adapter
adapter
adapter
adapter
a
10"
b
3-3/8"
T1U3351
T1U3352
T9N4352
TT1U3352
TX1U3352WT
T107-3350
T9J4359
T4T2353
T9N4353
PM1U3352SYL
PM1U3352RC
PM4T2353RP
T3G8354
PM1U1354
PM8J5357
T3G3357
PM3G5358
PM3G5359
PM8J3357
PM1U1357
PM1U1350
PM9J2357
8-1/8"
9-3/8"
10"
11-1/8"
11-1/2"
9-1/2"
9-7/8"
9-1/2"
10
10 1/4"
11"
11-5/8"
8-1/4"
11-1/4"
4-3/16"
3-7/8"
8-17/32"
8-17/32"
3-1/2"
4-1/8"
10-1/4"
3-3/8"
3-1/2"
3-1/4"
3-1/2"
3-15/16"
4-3/4"
7"
2"
4"
5"
2"
3-1/2"
3-3/4"
2-11/16"
3-3/4"
6"
5-7/8"
5-5/8"
5-5/8"
5-11/16"
6-1/8"
2"
5-3/4"
part no.
T7T3402
T8E4402
T6Y7409
PM6Y7409
PM7T3402RC
PM7T3404
a
11-1/16"
11-1/16"
10-1/2"
11-3/8"
12"
9-1/2"
b
3-7/8"
3-7/8"
2"
1-1/2"
4"
6-3/4"
c
2-11/16"
2-11/16"
2-11/16"
2-11/16"
2-11/16"
2-11/16"
2-11/16"
2-11/16"
2-11/16"
2-11/16"
d
3-5/16"
3-5/16"
3-5/16"
3-5/16"
3-5/16"
3-5/16"
3-5/16"
3-5/16"
3-5/16"
3-5/16"
2-11/16"
2-11/16"
2-11/16"
1-5/8"
1-1/2"
1-13/16"
1-11/16"
1-9/16"
1-9/16"
1-13/16"
1-3/4"
1-3/4"
1-1/2'
3 5/16"
3-5/16"
3-5/16"
35°
22°
23°
24°
38°
38°
23°
23°
23°
23°
lbs.
16.9
11.4
12.3
18.7
13
14.2
16
12.3
17.8
21.6
12.4
15.3
23
20.7
30.9
35.6
40.3
49
49
44
45
21
36.4
c
3-5/32"
3-5/32"
3-5/32"
3-5/32"
3-5/32"
1-7/8"
d
3-21/32"
3-21/32"
3-21/32"
3-21/32"
3-21/32"
22°
lbs.
25
25
21
17.5
23.5
6.7
40 Series
style
T
T
T
T
T
1
description
long
long h-d
penetrator
penetrator
rock chisel
adapter
45 Series
style
T
T
T
T
T
T
T
T
T
T
T
T
T
T
1
1
2
2
1
1
1
description
part no.
Fanggs dig
TF9W8452D
short
long
long h-d
tiger
twin tiger
flare
penetrator
abrasion h-d
abrasion
penetrator
ribbed sharp
rock chisel
rk penetrator
adapter
adapter
adapter
adapter
adapter
adapter
adapter
a
10"
b
3-3/8"
T9W8451
T9W8452
T9N4452
PM1U3452T
PM1U3452WT
T107-3450
T9J4459
T9N4453
PM9W1453
T9J4459
PM9W8452SYL
PM1U3452RC
PM9W1452RP
T1U1454
T8E6464
PM8J1454
PM9J9584
PM8E3464
PM8E3465
PM8E3466
10-3/8"
11-1/2"
13"
13-3/16"
13-3/16"
11-1/4"
11-5/8"
11 5/8"
11-5/8"
11-5/8"
12-1/2"
13-5/16"
14"
11-1/8"
11-1/8"
12-1/2"
12-1/2"
10-3/8"
10-3/8"
10-3/8"
4-1/2"
4-1/2"
4-1/2"
5-1/2"
7-1/4"
9"
2"
5-1/2"
5-1/2"
2"
4-3/4"
4-1/2"
4-3/4"
7-3/8"
7-3/8"
4-1/8"
4-1/8"
6-7/8"
6-7/8"
6-7/8"
part no.
T1U3551
T1U3552
PM9N4552
T9J4559
PM9W1553
PM6Y2553
PM1U3552RC
T9J4559
PM9W1553RP
PM1U1553
PM3G9494
PM3G9495
PM3G9496
a
12-1/2"
13-1/2"
14"
13-1/4"
13"
13-1/2"
14-3/4"
13"
15-3/16"
14-1/2"
14-1/2"
15"
15"
b
5-1/2"
5-1/2"
5-3/4"
2-5/8"
9"
7-5/8"
5-3/4"
2-5/8"
5-3/4"
8-5/8"
12-5/8"
13-3/8"
13-3/8"
c
3-17/32"
3-17/32"
3-17/32"
3-17/32"
3-17/32"
3-17/32"
3-17/32"
3-17/32"
3-17/32"
3-17/32"
3-17/32"
3-17/32"
3-17/32"
3-17/32"
d
3-29/32"
3-29/32"
3-29/32"
3-29/32"
3-29/32"
3-29/32"
3-29/32"
3-29/32"
3-29/32"
3-29/32"
3-29/32"
3-29/32"
3-29/32"
3-29/32"
lbs.
28.5
22.5
24.6
36.2
20.5
24.5
31.3
23.6
2"
2"
2-3/16"
2-3/16"
2-1/8"
2-1/8"
2-1/8"
24°
24°
23°
23°
22°
22°
22°
32.4
23.6
25.1
32.3
48.4
42
41.8
45.4
50
50
50
50
c
4-5/16"
4-5/16"
4-5/16"
4-5/16"
4-5/16"
4-5/16"
4-5/16"
4-5/16"
4-5/16"
2-7/16"
2-5/8"
2-5/8"
2-5/8"
d
4-11/32"
4-11/32"
4-11/32"
4-11/32"
4-11/32"
4-11/16"
4-11/16"
4-11/16"
4-11/16"
23°
22°
22°
22°
lbs.
35.5
33.5
59
35
50.5
67
45.5
32
66
77.2
70
70
70
55 Series
style
T
T
T
T
T
T
T
T
T
1
1
1
1
description
short
long
long h-d
penetrator
abrasion
abrasion h-d
rock chisel
penetrator
rk penetrator
adapter
adapter
adapter
adapter
70 Series
style
T
T
1
description
part no.
long
T4T4702
abrasion
T4T4703
adapter
T4T4704
a
16-5/16"
16-5/16"
12-3/4"
b
7
9
16-3/4"
c
6
6
3"
d
5-3/4"
5-3/4"
22°
lbs.
84
107.2
149
John Deere Replacement Teeth for Esco Conical Products
John Deere replacement teeth for Esco conical systems come in sizes and tooth
designs to fit almost all machine makes and models.
Conical Design
The "conical" design mating system
between tooth and adapter creates
self-tightening action. The raised
center area on the top and bottom of
the adapter nose piece fits tightly into
the formed area on the top and bottom
of the tooth pocket. This design
reduces tooth movement both vertically
and horizontally. The tooth and
adapter are designed as a bucket tooth
system that will absorb impact loads
and generally reduce the amount of
abrasive action to the bucket lip.
Part Number Explanation
Prefix
Suffix
PM
TF
PM
TL
T
AP
T
R
T
S
T
S_F
T
TVIP or TVIPA
Pin and Lock Retention
All John Deere replacement teeth for
Esco conical products are retained with
a pin and lock. Once the pin and lock
are installed, a snug fit gives this
attaching system little to no movement
and provides great strength throughout
the life of the tooth. We offer pins and
locks in the standard and ratchet
version. The standard is designed for
use in general-purpose applications.
The ratchet style provides secure
retention in more demanding
conditions and avoids "pin walk" in
heavy prying conditions.
(Replacement Teeth for Esco Products)
Explanation
NOTES: Nose Sizes
are identified by the
Dual Purpose Flare
first two numeric
Dual Purpose Long
digits of the
Abrasion Paneled
designation number.
Rock
The letter(s) following
Sharp
the nose size describe
Sharp_" Flare
the tooth shape.
Twin "V-Shaped" Paneled
(Twin Tiger)
T
VIP or VIPA
"V-Shaped" Paneled
(Tiger)
Examples:
Part Number T30S
Esco Replacement, 3.0 inches wide, sharp.
Part Number T25S5F
Esco Replacement, 2.5 inches wide, sharp, 5" flare.
John Deere Replacement Teeth for Esco Conical Products - Types
Available
Abrasion-Paneled Teeth
(AP Suffix) (Centerline)
Flare Teeth (S_F Suffix)
(Centerline)
Sharp Teeth (S Suffix)
(Centerline)
•
•
• Slim, penetrating profile.
For use in general-purpose to
heavy digging and loading
conditions.
•
Good for general-purposeto-to heavy-duty
applications.
Good penetration; self
sharpens.
For loading and digging in
loose, mud-like conditions.
Tiger Teeth
(VIP or VIPA Suffix)
(Non-Centerline)
Twin Tiger Teeth
(TVIP or TVIPA Suffix)
(Non-Centerline)
•
•
•
V-shaped and paneled for highimpact digging and loading.
Narrow bit for maximum
penetration; paneled to maintain
sharpness.
•
Two points on the V-shaped
tooth cut clearance for bucket
sides.
Can be used as center teeth for
maximum penetration.
Esco Conical - Teeth by Series
18 Series Conical
style
description
a sharp
c tiger
b twin tiger
tilt front
long
- std pin
pin
- std retainer
- adapter
tooth, long
rubber lock
adpt., W-O, bttm. leg, 1.25" lip
adpt., B-O, 1-1/2 leg, (Case W18, W20)
adpt., B-O, 2 leg, (Case 850B)
adpt., B-O, crnr., RH (Case 850B)
adpt., B-O, crnr., LH (Case 850B)
adpt., B-O, 1-1/2 leg, 1.06" thr
part no.
PM18SLHX
PM18VIPHX
PM18TVIPHX
PM18THX
PM18TL
PM18PN
PM18-20MPNP
PM18LK
PM833-18
PM18LPHX
PM18-20MLKR
PM855-18HX
PM4718-18HX
PM4729-18HX
PM5701R-18HX
PM5701L-18HX
PM5707-18HX
rcv. disc.
part no.
T25S
T25VIP
T25TVIP
T25S5F
PM25TF
T2530PN
T2530LK
T2530PNR
T2530LKR
PM855-25
PM3806-25
PM25THX
PM25RP
PM25RB
PM25RBS
PM4703-25HX
PM5710L-25HX
PM5710R-25HX
PMEWN25
rcv. disc.
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
non stock
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
N.S.
N.S.
N.S.
N.S.
N.S.
STK
used on
Competitive: Backhoes
25 Series Conical
style
a
c
b
d
d
-
description
sharp
tiger
twin tiger
flare, 5"
d-p flare
std pin
std retainer
ratchet pin
ratchet retainer
adpt., W-O, bttm., leg, 1.25 lip, 30 degrees
adapter
tooth, tilt front
pin, solid
rubber bushing
steel bushing
adpt., B-O, 1-1/2 leg, (Case 1150)
adpt., B-O, crnr., LH
adpt., B-O, crnr., RH
nose, W-O
non stock
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
N.S.
N.S.
N.S.
STK
used on
JD: 190E, 290D, Competitive: Backhoes,
Clamshells, Draglines, Excavators, Face Shovels,
Loaders, Scrapers, Shovel Dippers
30 Series Conical
style
a
c
b
d
-
description
sharp
tiger
twin tiger
flare, 6"
std pin
std retainer
ratchet pin
ratchet retainer
adapter
adapter
adapter
tooth, tilt front
adpt., W-O, bttm. leg, 1.25" to 1.5" lip
adpt. nose, W-O
part no.
T30S
T30VIP
T30TVIP
T30S6F
T2530PN
T2530LK
T2530PNR
T2530LKR
PM3807-30
TH108948
TH103467
PM30THX
PM838-30HX
PM855-30HX
PMEWN30
rcv. disc.
9
9
9
9
9
9
9
9
9
9
9
non stock
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
N.S.
part no.
T35S
T35VIPA
T35TVIPA
T35S6F
PM3808-35
T35PN
T3540LK
T35PNR
T3540LKR
EX119-35
EX20SP
EX20W2
EX20W3
EX20W1
PM136-35HX
PMP136
PM822-35HX
PM839-35HX
PM1899-35HX
PM1875-35HX
PMEWN35
rcv. disc.
9
9
9
9
9
9
9
9
9
9
9
9
9
9
non stock
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
N.S.
STK
N.S.
N.S.
STK
STK
N.S.
part no.
T40S
T40VIPA
T40TVIP
T40S7F
PM3809-40
TH111281
TH109817
TH102450
T40PN
T3540LK
T40PNR
T3540LKR
PM236-40HX
PM129-40HX
PMP236
PMEWN40
rcv. disc.
9
9
9
9
9
9
9
9
9
9
9
9
non stock
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
N.S.
STK
STK
STK
used on
JD: 490, 490D, 490E, 495D, 590D, 595, 595D,
Competitive: Clamshells, Draglines, Excavators,
Face Shovels, Loaders, Scrapers, Shovel Dippers
35 Series Conical
style
a
c
b
d
-
description
sharp
tiger
twin tiger
flare, 6"
adapter
std pin
std retainer
ratchet pin
ratchet retainer
adapter
spool
wedge
wedge
wedge
adpt., stake-type, for C-19 Hensley
flex pin for C-19 Hensley lips (136-35HX)
adpt., W-O, 1-1/2 leg, 1.5" lip
adpt., W-O, 1-1/2 leg, 1.25" lip
adpt., nose, W-O
used on
JD: 690, 690A, 690B, 690C, 690D, 690E,
40 Series Conical
style
a
c
b
d
-
description
sharp
tiger
twin tiger
flare
adapter
adapter
adapter
adapter
std pin
std retainer
ratchet pin
ratchet retainer
adpt., stake-type, for Hensely lips
adpt., stake-type, for C-29 ESCO lips
flex pin for C-29 Hensley lips (236-40)
adpt., nose, W-O
used on
JD: 790, 790D, 790E, 792, 792D, Competitive:
Clamshells, Draglines, Excavators, Face Shovels,
Loaders, Scrapers, Shovel Dippers
45 Series Conical
style
a
c
b
d
-
description
sharp
tiger
twin tiger
flare, 8"
tooth, long
tooth, rock chisel
adapter
std pin
std retainer
ratchet pin
ratchet retainer
adpt., stake-type, ESCO C-29 lip
spool
wedge
wedge
wedge
flex pin for C-29 ESCO lips (236-40)
adpt., stake-type, Hensley C-29
flex pin for C-29 Hensley lips (236-40)
adpt., W-O bttm. leg
adpt., W-O 1-1/2 leg 2" lip
adpt., nose, W-O
part no.
T45S
T45VIPA
T45TVIP
T45S8F
PM45LPHX
PM45RDXHX
AT131709
T45PN
T45LK
T45PNR
T45LKR
EX129-45
EX29SP
EX29W1
EX29W2
EX29W3
PM129-45HX
PMP236
PM236-45HX
PMP236
PM840-45HX
PM2810-45HX
PMEWN45
rcv. disc.
9
9
9
9
part no.
PM50SHX
PM50SLHX
PM50VIPHX
PM50TVIPHX
PM50RHX
PM50RDXHX
PM50APHX
PM50S9FHX
PM50LPHX
PM50PNP
PM50LKR
PM50PNRP
PM50LKRR
PM3811-50HX
PMEWN50
rcv. disc.
non stock
STK
N.S.
STK
N.S.
N.S.
STK
N.S.
N.S.
N.S.
STK
STK
STK
STK
N.S.
N.S.
used on
description
part no.
sharp
PME55HX
sharp short
PM55SSHX
sharp long
PM55LPHX
tiger
PM55VIPHX
twin tiger
PM55TVIPHX
rock
PM55RHX
rock chisel
PM55RDXHX
abrasion panel
PM55APHX
flare, 10"
PM55S10FHX
slag
PM55AHX
heavy slag
PM55AHHX
panel sharp
PM55SPHX
pin
PM55PNP
ratchet pin
PM55PNRP
wedge pin
PM55PNTP
rubber lock
PM55LKR
ratchet rub lock
PM55LKRR
adpt., W-O, 1-1/2 leg, 3 straight lip, 23 degre PM1856-55HX
adpt., nose, W-O
PMEWN55
rcv. disc.
non stock
N.S.
N.S.
STK
N.S.
N.S.
STK
STK
N.S.
N.S.
N.S.
N.S.
N.S.
STK
STK
STK
STK
STK
N.S.
N.S.
used on
9
9
9
9
9
9
9
9
9
9
non stock
STK
STK
STK
STK
N.S.
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
N.S.
STK
N.S.
STK
N.S.
used on
JD: 890, 890A, 892D, 892E, 992D, 992E,
50 Series Conical
style
a
a
c
b
-
description
sharp
long sharp
tiger
twin tiger
rock
rock chisel
abrasion panel
flare, 9"
long
pin
rubber lock
ratchet pin
ratchet rub lock
adpt., W-O, 1-1/2 leg, 2.25 lip, 30 degrees
adpt., nose, W-O
55 Series Conical
style
a
a
a
c
b
d
-
Early "R" Series Conical
style
description
tooth
pin
rubber plug
part no.
PMR2HX
PMR2P
PMR2R
PMCB11255R2H
rcv. disc.
non stock
STK
STK
STK
STK
used on
Competiitive: Clamshells, Draglines, Excavators,
Face Shovels, Loaders,
Scrapers, Shovel Dippers
Esco Super Conical- Applications
36 Series Super Conical
style description
flared panel
tilt front
c
tiger
lock
pin
part no.
PM36FPHX
PM36THX
PM36VIPHX
PM36LKR
PM36PNP
rcv. disc.
part no.
PM46ARLHX
PM46RHX
PM46FPHX
PM46THX
PM46VIPHX
PM46LKR
PM46PNP
rcv. disc.
part no.
PM56ARLHX
PM56FPHX
PM56RHX
PM56VIPHX
PM56LKR
PM56PNP
rcv. disc.
part no.
PMT1154CHX
PMT1155CHX
PMT2143AHX
PMT2144AHX
PMT1156AHX
PMT1157AHX
PMPDE31329HX
rcv. disc.
non stock
STK
N.S.
N.S.
STK
STK
used on
style description
long rock
rock
flared panel
tilt front
c
tiger
lock
pin
non stock
N.S.
STK
STK
N.S.
N.S.
STK
STK
used on
style description
long rock
d
flared panel
rock
c
tiger
lock
pin
non stock
N.S.
N.S.
N.S.
N.S.
STK
STK
used on
Competiitive: Clamshells, Draglines,
Excavators, Face Shovels, Loaders,
Sidecutters
style description
sidecutter, LH, 4" add'1
sidecutter, RH, 4" add'1
sidecutter, strikeoff
non stock
STK
STK
N.S.
STK
STK
STK
STK
used on
Esco Ripper Teeth- Applications
22 Series
style description
tooth, ripper
bushing
pin
part no.
PM22R10HX
PM22RBGB
PM22RPGP
rcv. disc.
part no.
PM25R11HX
PM25R12HX
PM25RNHX
EX25R12
rcv. disc.
non stock
STK
STK
STK
used on
25 Series
style description
tooth, ripper
tooth, ripper
ripper, nose, W-O
tooth, ripper
non stock
STK
STK
STK
STK
used on
35 Series
style description
ripper tooth
tooth, ripper 14
tooth, ripper 15
tooth, ripper 15
tooth, ripper, tiger, 15
tooth, ripper, twin tiger, 14
bushing, rubber
bushing, slag
pin, solid
part no.
T35-5R15
PM35R14HX
PM35R15HX
PM35R15AHX
PMT35R15
PM35RWTHX
PM35RB
PM35RBS
PM35RP
rcv. disc.
9
part no.
PM39-5R17AHX
PM39RP
rcv. disc.
non stock
STK
STK
STK
STK
N.S.
N.S.
STK
STK
STK
used on
39 Series
style description
tooth, ripper
pin
bushing
PM39RB
non stock
STK
STK
STK
used on
Esco Conical - Specifications
T
Type 4
18 Series Conical
style
T
T
T
T
T
4
description
long
sharp
tilt front
tiger
twin tiger
adapter
tooth, long
pin
rubber lock
tooth, ripper
adpt., W-O, bttm. Leg, 1.25" lip
adpt., B-O, 1-1/2 leg, (Case W18, W20)
adpt., B-O, 2 leg, (Case 850B)
adpt., B-O, crnr., RH (Case 850)
adpt., B-O, crnr., LH (Case 850)
adpt., B-O, 1-1/2 leg, 1.06" thr
part no.
PM18TL
PM18SLHX
PM18THX
PM18VIPHX
PM18TVIPHX
PM833-18
PM18LPHX
PM18-20MPNP
PM18-20MLKR
PM22R10HX
PM855-18HX
PM4718-18HX
PM4729-18HX
PM5701R-18HX
PM5701L-18HX
PM5707-18HX
a
4-11/16"
5-7/8"
4-13/16"
6-7/8"
6-7/8"
-
b
2-1/8"
2-1/8"
2-3/16"
3/8"
3"
3/4"
c
1-13/16"
1-13/16"
1-13/16"
1-13/16"
1-13/16"
3-7/8"
d
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
23°
lbs.
3.1
1.9
1.8
2.5
3
3.3
2.1
0.1
0.1
8
4.2
6.6
8.5
12
12
6.5
part no.
T25S
T25VIP
T25TVIP
T25S5F
PM25TF
PM855-25
PM3806-25
PM25THX
PM4703-25HX
PM5710L-25HX
PM5710R-25HX
PMEWN25
a
6-5/8"
8-1/8"
8"
6-1/2"
6-5/16"
-
b
2-1/2"
1/8"
3-1/4"
4-7/8"
3-5/16"
1"
-
c
2-1/2"
2-1/2"
2-1/2"
2-1/2"
2-1/2"
5-1/4"
-
d
2-1/8"
2-1/8"
2-1/8"
2-1/8"
2-1/8"
23°
20°
11/16"
3-1/16"
2-7/8"
-
lbs.
5.6
6.9
7.4
7.4
6.0
7.3
10.5
4.8
12.5
12.8
12.5
4.9
25 Series Conical
style
T
T
T
T
T
4
2
description
sharp
tiger
twin tiger
flare, 5"
d-p flare
adapter
adapter
tooth, tilt front
adpt., B-O, 1-1/2 leg, (Case 1150)
adpt., B-O, crnr., LH
adpt., B-O, crnr., RH
nose, W-O
30 Series Conical
style
T
T
T
T
2
1
1
description
sharp
tiger
twin tiger
flare, 6"
adapter
adapter
adapter
tooth, tilt front
nose, W-O
part no.
T30S
T30VIP
T30TVIP
T30S6F
PM3807-30
TH108948
TH103467
PM 30THX
PM 838-30HX
PM 855-30HX
PMEWN30
a
6-1/2"
8-1/4"
8-1/4"
6-5/8"
6-1/2"
3-1/2"
4-14"
b
3-1/8"
1/8"
3-3/4"
6"
1-1/4"
1-5/16"
1-5/16"
c
3"
3"
3"
3"
6"
8"
9-7/8"
d
2-1/4"
2-1/4"
2-1/4"
2-1/4"
23°
25°
15°
3/4"
3-1/8"
3-3/8"
-
part no.
T35S
T35VIP
T35TVIPA
T35S6F
PM3808-35
EX119-35
PM136-35HX
PM822-35HX
PM839-35HX
PM1899-35HX
PM1875-35HX
PMEWN35
a
7-3/4"
10/7/2016
10"
7-3/4"
6-1/4"
6-1/4"
b
3-5/8"
1/8"
4-1/4"
6"
1-5/8"
1-5/8"
c
3-1/2"
3-1/2"
3-1/2"
3-1/2"
5-3/4"
6-1/4"
d
2-5/8"
2-5/8"
2-5/8"
2-5/8"
23°
13°
3/4"
3-5/8"
4"
-
part no.
T40S
T40VIPA
T40TVIP
T40S7F
PM3809-40
TH111281
TH109817
TH102450
PM236-40HX
PM129-40HX
PMEWN40
a
9"
12-5/16"
10"
8-3/4"
7-1/2"
4"
4"
6-1/4"
b
4-1/4"
1/4"
4-3/4"
6-5/8"
1-5/8"
1-5/8"
1-1/2"
1-5/8"
c
4"
4"
4"
4"
7"
8-3/4"
8-3/4"
10-3/4"
d
3"
3"
3"
3"
23°
17°
18°
43°
1"
4-1/4"
4-1/2"
-
lbs.
6.6
7.2
9.3
8.5
17.0
13.9
17.5
6.0
11.1
9.2
5.6
35 Series Conical
style
T
T
T
T
2
3
description
sharp
tiger
twin tiger
flare, 6"
adapter
adapter
adpt., stake-type, for C-19 Hensley
adpt., W-O, 1-1/2 leg, 1.5" lip
adpt., W-O, 1-1/2 leg, 1.25" lip
nose, W-O
lbs.
10.6
6.9
11.2
11.7
19.4
17.1
19.4
25.0
22.1
22.6
20.6
9.4
40 Series Conical
style
T
T
T
T
2
1
1
1
description
sharp
tiger
twin tiger
flare
adapter
adapter
adapter
adapter
adpt., stake-type, for Hensley
adpt., stake-type, for C-29 ESCO lips
nose, W-O
lbs.
14.5
15.4
16.6
15.1
33.1
26.0
27.2
28.4
43.8
27.0
13.7
45 Series Conical
style
T
T
T
T
2
3
description
sharp
tiger
twin tiger
flare, 8"
tooth, long
tooth, rock chisel
adapter
adpt., W-O bttm. leg
nose, W-O
part no.
T45S
T45VIPA
T45TVIP
T40S8F
PM45LPHX
PM45RDXHX
AT131709
EX129-45
PM129-45HX
PM236-45HX
PM840-45HX
PM2810-45HX
PMEWN45
a
10"
13-3/4
11"
9-7/8"
b
4-5/8"
1/4"
5-1/2"
7-3/4"
c
4-1/2"
4-1/2"
4-1/2"
4-1/2"
d
3-1/4"
3-1/4"
3-1/4"
3-1/4"
7-1/4"
9"
2-1/4"
2-1/2"
7-1/4"
9"
25°
17°
1-1/16"
4-1/2"
5"
-
c
4-7/8"
4-7/8"
4-7/8"
4-7/8"
4-7/8"
4-7/8"
4-7/8"
4-7/8"
4-7/8"
d
3-13/16"
3-13/16"
3-13/16"
3-13/16"
3-13/16"
3-13/16"
3-13/16"
3-13/16"
3-13/16"
lbs.
20.8
22.9
24.8
25.2
16.4
17.7
44.0
33.3
32.7
48.5
35.1
45.2
17.9
50 Series Conical
style
T
T
T
T
T
T
T
T
T
description
sharp
long sharp
tiger
twin tiger
rock
rock chisel
abrasion panel
flare, 9"
long
adpt., W-O, 1-1/2 leg, 2.25 lip, 30 degrees
nose, W-O
part no.
PM50SHX
PM50SLHX
PM50VIPHX
PM50TVIPHX
PM50RHX
PM50RDXHX
PM50APHX
PM50S9FHX
PM50LPHX
PM3811-50HX
PMEWN50
a
b
11-1/8" 5-11/16"
11-1/8"
5-1/4"
15"
5/8"
13"
6-1/2"
10-5/8"
5-1/4"
12"
3"
11-3/4"
5-3/4"
11"
9"
11-15/16" 5-1/8"
1-3/8"
5-5/16"
5-1/16"
-
a
b
c
d
10-5/16"
13-1/4"
16-1/2"
15-1/2"
11-1/8"
13-1/2"
12-3/4"
11-1/4"
11-3/8"
12-3/16"
12"
6"
6"
3/4"
7"
6"
3-3/8"
6-1/2"
10"
6"
6"
5-1/2"
5-3/8"
5-3/8"
5-3/8"
5-3/8"
5-3/8"
5-3/8"
5-3/8"
5-3/8"
5-3/8"
5-3/8"
5-3/8"
4-1/4"
4-1/4"
4-1/4"
4-1/4"
4-1/4"
4-1/4"
4-1/4"
4-1/4"
4-1/4"
4-1/4"
4-1/4"
lbs.
22.4
23.0
31.6
34.8
23.7
20.3
30.9
28.8
26.9
60.4
23.7
55 Series Conical
style
T
T
T
T
T
T
T
T
T
T
T
description
tooth, std.
sharp short
sharp long
tiger
twin tiger
rock
rock chisel
abrasion panel
flare, 10"
abrasion
heavy slag
panel sharp
adpt., W-O, 1-1/2 leg, 3 straight lip, 23 degrees
nose, W-O
part no.
PME55HX
PM55SSHX
PM55LPHX
PM55VIPHX
PM55TVIPHX
PM55RHX
PM55RDXHX
PM55APHX
PM55S10FHX
PM55AHX
PM55AHHX
PM55SPHX
PM1856-55HX
PMEWN55
lbs.
27.4
25.9
36.1
43.1
51.2
31.5
31.9
39.0
35.0
34.6
44.6
31.5
81.0
31.2
Early "R" Series Conical
style
description
tooth
rubber plug
Adpt., W-O, bttm. leg, 1.25" lip
part no.
PMR2HX
PMR2R
PMCB11255R2H
a
b
c
d
lbs.
3.0
0.1
5.5
a
8-3/4"
8"
10"
b
3-3/4"
4"
7/16"
c
2-5/16"
2-5/16"
2-5/16"
d
2-3/8"
2-3/8"
2-3/8"
lbs.
7.8
8.6
8.1
Esco Super Conical - Specifications
style
T
flared panel
T
tilt front
T
tiger
description
part no.
PM36FPHX
PM36THX
PM36VIPHX
style
T
T
T
T
T
description
long rock
rock
flared panel
tilt front
tiger
part no.
PM45ARLHX
PM46RHX
PM46FPHX
PM46THX
PM46VIPHX
a
b
c
d
lbs.
11-7/8"
10-1/8"
5"
3-3/4"
2-3/4"
2-3/4"
3-3/16"
3-3/16"
10-1/2"
12-7/8"
4-1/4"
5/8"
2-3/4"
2-3/4"
3-3/16"
3-3/16"
25.7
16.7
17.8
17.8
17.4
a
b
c
d
lbs.
14-1/2"
14"
12-3/4"
15-1/2"
6-1/4"
5-1/2"
4-1/2"
5/8"
3-3/8"
3-3/8"
3-3/8"
3-3/8"
4-3/16"
4-3/16"
4-3/16"
4-3/16"
49.5
36.0
31.4
36.2
a
b
c
d
lbs.
53.5
54.8
43.6
44.4
59.0
59.5
37.0
4.9
style
T
T
T
T
description
long rock
flared panel
rock
tiger
part no.
PM56ARLHX
PM56FPHX
PM56RHX
PM56VIPHX
Sidecutters
style
description
sidecutter, LH, 4" add"1
sidecutter, RH, 4" add"1
sidecutter, strikeoff
adpt. nose, W-O
part no.
PMT1154CHX
PMT1155CHX
PMT2143AHX
PMT2144AHX
PMT1156AHX
PMT1157AHX
PMPDE31329HX
PMEWN25
Esco Ripper Teeth- Specifications
22 Series
style
description
part no.
PM22R10HX
a
b
c
d
lbs.
8.0
description
part no.
PM25R11HX
PM 25R12HX
PM 25RNHX
a
b
c
d
lbs.
11.0
13.1
18.1
description
tooth, ripper 14
tooth, ripper 15
tooth, ripper 15
tooth, ripper, tiger, 15
tooth, ripper, twin tiger, 14
ripper tooth
part no.
PM35R14HX
PM35R15HX
PM35R15AHX
PMT35R15
PM35RWTHX
T35-5R15
a
b
c
d
lbs.
26.0
27.1
29.0
30.0
31.8
30.4
part no.
PM39-5R17AHX
a
b
c
d
lbs.
43.6
tooth, ripper
25 Series
style
tooth, ripper
tooth, ripper
ripper, nose, W-O
35 Series
style
39 Series
style
description
tooth, ripper
Replacements for Esco Conical Products
Retainers
PM18LK - 18 Series
T2530LKR - 25 and 30 Series
T2530LK - 25 and 30 Series
T3540LKR - 35 and 40 Series
T3540LK - 35 and 40 Series
T45LKR - 45 Series
T45LK - 45 Series
Esco Conical
13
Replacements for Esco Conical Products
T2530PN
25 and 30 Series
T45PN
45 Series
T45PNR
T40PN
40 Series
T40PNR
T35PN
35 Series
T35PNR
T2530PNR
25 and 30 Series
PM18PN
18 Series
Esco Conical
14
Esco Helilok®/Vertalok® Systems
Style a
Style b
Style c
Standard Teeth (SYL Suffix)
(Centerline)
Tiger Teeth (VIP Suffix)
(Non-Centerline)
Twin Tiger Teeth (TVIP Suffix)
(Non-Centerline)
•
•
•
•
For general-purpose to heavyduty digging and loading
Excellent penetration and wear
Style d
High penetration for frost and
tough material
Style e
(Centerline)
Chisel Teeth (SD Suffix)
(Centerline)
•
•
•
•
•
•
For digging and loading in
extremely tight material
Use as a corner tooth with tiger
teeth in the center
For digging in mud-like
conditions
Wide bite for trench cleanup
Chisel shape with sharp profile
Excellent penetration
Greater wear than tiger or twin
tiger teeth
Part Number Explanation for Esco Helilok®/Vertalok® Teeth
Prefix
Suffix
Explanation
EX
EX
EX
EX
EX
EX
ARL
SD
S_F
SYL
VIP
TVIP
Abrasion
Chisel
Flare (S5F indicates a sharp edge with a 5" flare)
Standard
Tiger
Twin Tiger
Esco Helilok® Vertalok® System
Helilok/Vertalok teeth are designed to give you up
to 20% more wear material up-front over other
tooth systems. As a result, more time can be spent
digging and loading rather than replacing teeth.
Teeth mount on both the Vertalok and Helilok
adapters with a quarter turn and butt up against the
adapter nose to take thrust loads head-on. The
helical threads and large stabilizing flats at the end
of the nose deliver maximum resistance to severe
breakout forces. Digging forces are distributed
over the entire nose surface which results in added
strength and durability.
With Quadrilok, the helical threads create a "locknut" force to resist shock
loads and keep point securely locked.
Loading stresses are distributed over the entire nose for unmatched
resistance to breakout and digging forces.
Greater strength and load bearing area.
Point twists onto the adapter with a quarter turn.
Helilok® Vertalok® Adapters
Horn Style
Available for Esco Horn-style lips
1 1/2 (Top Leg)
Extra strength and weld surface for
tough digging conditions
Side Cutter
Tooth-type side cutters cut extra clearance
1 1/2 (Bottom) Leg
Fits a wide range of lip thicknesses.
Designed for general-purpose use backhoes - excavators
Spherical
Designed for Esco S19 and S29 series bucket lips
Esco Helilok®/Vertalok® Systems
®
Quadrilok
®
Quadrilok
®
(For Helilok
Pin and Plug (For Vertalok® Adapters)
Adapters)
®
Retainer for Helilok
Retainers
Pin and Plug for Vertalok® Adapters
Adapters
Teeth are held on to Helilok® adapters by a driveon, one-piece Quadrilok® retaining system. With
the Quadrilok, the helical threads create a lock-nut
force that tightens under load and resists rotation
under the most severe impact.
The U-shaped Quadrilok eliminates the need for
snap rings or rubber-bonded locks, and it prevents
the tooth from rotating.
Teeth are securely fastened to Vertalok adapters
with a drive-through pin which provides
maximum holding power and virtually eliminates
tooth loss.
The pin is held in place by a spring-loaded plug
that fits snugly into a cavity in the side of the
adapter nose. Both the pin and the plug are
reusable provided they are not damaged.
Pins can be removed with a pin or punch.
Special Tools for Quadrilok® Adapters
For removal and installation of the 21 and 27 Series Teeth, use special tool EX21-27QRT.
For the 37, 47, and 57 Series, use special tool EX3-4-57QRT.
Special tools for Vertalok® Adapters
For removal and installation of 37, 47 and 57 series Vertalok teeth, use special tool EXPRT
Spool and Wedge Adapter Locks for Horn Style Adapters: Install a spool in front of the key slot and a wedge in the rear
of the key slot. Oversize wedges are available to compensate for wear. Use a standard wedge (W1) when installing a new
adapter on a new or reconditioned lip. When the W1 is nearly flush with the top of the lip, replace it with a W2 wedge.
When the W2 wedge drives flush, replace it with a W3 wedge. To avoid lip damage, rebuild the adapter promptly when a
W3 drives flush with the top of the lip.
Series
21 or 27
37
Fluted Spool
EX20SP
EX29SP
W1
EX230W1
EX29W1
Side Wear Shroud (bolt-on)
EX31329-X
A
B
Weight
3.95
5.97
40
Fluted Wedge
W2
EX20W2
EX29W2
W3
EX20W3
EX29W3
Esco Helilok® / Vertalok® Products
Retainers
Quadrilok® for Helilok® Adapters
EX21LKS
21 Series
EX37LKS
37 Series
EX27LKX
27 Series
Esco Helilok®Vertalok® Products
Retainers
Quadrilok® for Helilok® Adapters; Pins for Vertalok® Adapters
EX57LKS
57 Series
EX27VPL
27 Series
EX37VPL
37 Series
EX47VPL
47 Series
EX57VPL
57 Series
Esco Helilok®Vertalok® Products
Quadrilok® for Helilok® Adapters
Retainers
Illustrated parts
are actual size
EX47LKS
47 Series
EX57VPN
57 Series
EX47VPN
47 Series
EX37VPN
37 Series
EX27VPN
27 Series
ESCO Helilok®/Vertalok® - Specifications
T
7
17 Series
style
T
description
standard
part no.
EX17TL
a
5-1/2"
b
1-7/8"
c
1-1/2"
d
1-3/4"
lb
2.3
part no.
EX21SYL
EX21VIP
EX21TVIP
EX21S5F
EX119-21
EX360-21
EX1550-21
EX1551-21
a
7-1/2"
7-1/8"
7-1/8"
7-1/2"
1-5/8"
2-1/2"
4-5/8"
4-5/8"
b
3"
1/4"
3-1/4"
5"
5-7/8"
2-3/8"
6"
6"
c
1-5/8"
3-7/8"
3-7/8"
3-7/8"
d
1-1/4"
4-3/4"
-
lb
6.7
5.9
7.2
10.4
15.4
15.0
21.8
21.7
21 Series
style
T
T
T
T
3
7
4
4
description
standard
tiger
twin tiger
5" flare
adapter
adapter
adapter
adapter
Esco Helilok®/Vertalok® - Tooth by Series
17 Series
style description
a
standard
part no.
EX17TL
disc. used on
ü
Competitive: backhoes, mini-excavators
21 Series
style
a
c
b
f
-
description
standard
tiger
twin tiger
5" flare
Quadrilok
adapter
adapter
adapter
adapter
adapter
adapter
part no.
EX21SYL
EX21VIP
EX21TVIP
EX21S5F
EX21LKS
EX119-21
EX360-21
EX1550-21
EX1551-21
EX5854-21
EX5849-21
disc. used on
ü
ü
ü
ü
ü
JD: 190E, 290D, 490, 490D, 490E, 495D Competitive: backhoes,
ü excavators
ü
ü
ü
ü
ü
27 Series
style
a
c
b
f
d
e
description
standard
tiger
twin tiger
6" flare
chisel
HD Sharp
part no.
EX27SYL
EX27VIP
EX27TVIP
EX27S6F
EX27SD
EX27S
ü
ü
ü
ü
ü
ü
used on
JD: 590D, 595, 595D, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D
Competitive: backhoes, excavators Case: 9030; Cat: EL180, EL200B,
215D, EL240B, All B and S family, EL180, EL200B, EL240B, Daewoo:
DH130, DH170, DH180, DH200, Dresser: 545, Fiat-Allis: FX150,
FX200, Gradall: Tracksta, Hyundai: R130, R200, JCB: 818, 820,
Kawasaki: 90ZIII, Kobelco: SK200IV, SJ229IV, Koehring: 6612,
6615, 6620, Komatsu, PC200-6, PC210-6, WA380-1. WA400-1, WA450-
27 Series
style
-
description
Quadrilok
adapter
adapter
adapter
adapter
adapter
pin
plug
adapter
part no.
EX27LKX
EX119-27
EX360-27
EX1550-27
EX1551-27
EX5827-27
EX27VPN
EX27VPL
EX5850-27V
ü
ü
ü
ü
ü
ü
ü
ü
ü
used on
JD: 590D, 595, 595D, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D
Competitive: backhoes, excavators Case: 9030; Cat: EL180, EL200B,
215D, EL240B, All B and S family, EL180, EL200B, EL240B, Daewoo:
DH130, DH170, DH180, DH200, Dresser: 545, Fiat-Allis: FX150,
FX200, Gradall: Tracksta, Hyundai: R130, R200, JCB: 818, 820,
Kawasaki: 90ZIII, Kobelco: SK200IV, SJ229IV, Koehring: 6612,
6615, 6620, Komatsu, PC200-6, PC210-6, WA380-1. WA400-1, WA4502, WA500-1, Liebherr: R912, R922, Link-Belt: LS2700Q, LS2800Q,
MDI/Yutani: MD200BLC, MD240BLC, MD240LC, O&K Trojan:
RH8, RH9, Samsung: SE210, L160, Yutani: MD200C, MD240C
37 Series
style
a
c
b
f
f
d
e
-
-
description
standard
tiger
twin tiger
7' flare
8' flare
Chisel
HD Sharp
Quadrilok
part no.
EX37SYL
EX37VIP
EX37TVIP
EX37S7F
EX37S8F
EX37SD
EX37SH
EX37LKS
used on
ü
ü
ü
ü
ü
ü
ü
ü
adapter
adapter
adapter
adapter
pin
plug
adapter
EX450-37
EX5824-37
EX1506-37
EX1507-37
EX37VPN
EX37VPL
EX5856-37V
ü
ü
ü
ü
ü
ü
ü
JD:690C, 690D, 690E, 790, 790D, 790E, 792, 792D, 892D, 892E, 922D,
922E, Case: 9040, 9050, Caterpillar: 225D, 231D, 980F, 988F, All C , D,
E Family, EL300B, Competitive: Excavators, Daewoo: DH220,
DH280, DH320, Dresser: 555,560B, Fiat-Allis: FX220, FX300, Hyundai:
R280, R290, R320, 95ZIII, 110III, Kobelco: SK300IV, Koehring: 6625,
6627, 6633, Komatsu: PC220-6, PC250-6, PC300-5, Liebherr: R932,
R942, Link-Belt: LS3400Q, LS4300Q, MDI/Yutani: MD300LC,
MD320BLC, O&K Trojan, RH11, RH12, Samsung: SE280, SE350,
VME: L190B, L270B, Yutani: 320BLC
47 Series
style
a
c
b
f
d
e
-
description
standard
tiger
twin tiger
9' flare
chisel
HD Sharp
Quadrilok
adapter
adapter
pin
plug
adapter
part no.
EX47SYL
EX47VIP
EX47TVIP
EX47TS9F
EX47SD
EX47SH
EX47LKS
EX450-47
EX1829A-47
EX47VPN
EX47VPL
EX5857-47V
used on
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
ü
JD: 892D, 892E, 992D, 992E, 9060, Caterpillar: 235C, 245B, All F, G
Family, EL450, Competitive: Loaders, Daewoo: DH450, Demag:
H40, Dresser: 570, Fiat-Allis: FX400, Hyundai: R450, Kawasaki:
115ZIII, Kobelco: SK400IV, SK600IV, Koehring: 6644, Komatsu:
PC400-5, WA600-1, Liebherr: R952, R954, R962, Link-Belt: LS5800CII,
MDI/Yutani: MD400LC, MD450BLC, O&K Trojan: RH18, RH20,
Samsung: SE450,
57 Series
style
a
c
b
-
description
standard
tiger
twin
pin
plug
Quadrilok
adapter
part no.
EX57SYL
EX57VIP
EX57TVIP
EX57VPN
EX57VPL
EX57LKS
EX1856A-57V
used on
ü
ü
ü
ü
ü
ü
ü
Caterpillar: 245B, 245BLC, 245ME, 922, 922C, Competitive: Loaders,
Demag: H55, H65, H85, H121, Kobelco: SK400IVME, Komatsu:
PC650-3, WA700-1, WA800-2, Liebherr: R962, R972, R972HD, R974,
R981, R982, Link-Belt: LS7400CII, MDI/Ytani: SK400, O&K Trojan:
RH30C, RH30D, RH40C, VME: 480, L320, L480
MACHINE APPLICATION FOR HELILOK /VERTALOK SYSTEMS
Company
Equipment
Series
Demag
H40-------------------------------------------------------------------------------47
H55, H65, H85, H121---------------------------------------------------------57
Dresser
545 -------------------------------------------------------------------------------27
555, 560B -----------------------------------------------------------------------37
570 -------------------------------------------------------------------------------47
Fiat-Allis
FX150, FX200------------------------------------------------------------------27
FX220, FX300------------------------------------------------------------------37
FX400 ---------------------------------------------------------------------------47
Gradall
Tracksta -------------------------------------------------------------------------27
Hyundai
R130, R200 ---------------------------------------------------------------------27
R280, R290, R320 -------------------------------------------------------------37
R450 -----------------------------------------------------------------------------47
JCB
818, 820 -------------------------------------------------------------------------27
Kawasaki
90ZIII----------------------------------------------------------------------------27
95ZIII, 110ZIII -----------------------------------------------------------------37
115ZIII --------------------------------------------------------------------------47
Kobelco
SK200IV, SK220IV -----------------------------------------------------------27
SK300IV ------------------------------------------------------------------------37
SK400IV ------------------------------------------------------------------------47
SK400IVME--------------------------------------------------------------------57
SK600IV ------------------------------------------------------------------------47
Koehring
6612, 6615, 6620---------------------------------------------------------------27
6625, 6627, 6633---------------------------------------------------------------37
6644------------------------------------------------------------------------------47
Komatsu
PC200-6, PC210-6 -------------------------------------------------------------27
PC220-6, PC250-6, PC300-5-------------------------------------------------37
PC400-5 -------------------------------------------------------------------------47
PC650-3 -------------------------------------------------------------------------57
WA380-1, WA400-1, WA450-2, WA500-1 -------------------------------27
WA600-1------------------------------------------------------------------------47
WA700-1, WA800-2 ----------------------------------------------------------57
Liebherr
R912, R922 ---------------------------------------------------------------------27
R932, R942 ---------------------------------------------------------------------37
R952, R954 ---------------------------------------------------------------------47
R962 -----------------------------------------------------------------------------47
57
R972, R972HD, R974, R981, R982 -----------------------------------------57
MACHINE APPLICATION FOR HELILOK /VERTALOK SYSTEMS
Company
Equipment
Series
Link-Belt
LS2700Q, LS2800Q -----------------------------------------------------------27
LS3400Q, LS4300Q -----------------------------------------------------------37
LS5800CII ----------------------------------------------------------------------47
LS7400CII ----------------------------------------------------------------------57
MDI/Yutani
MD200BLC, MD240BLC, MD240LC -------------------------------------27
MD200C, MD240C------------------------------------------------------------27
MD300LC-----------------------------------------------------------------------37
MD320BLC---------------------------------------------------------------------37
MD400LC, MD450BLC ------------------------------------------------------47
SK400 ---------------------------------------------------------------------------57
O&K Trojan
RH8, RH9 -----------------------------------------------------------------------27
RH11, RH12 --------------------------------------------------------------------37
RH18, RH20 --------------------------------------------------------------------47
RH30C, RH30D, RH40C -----------------------------------------------------57
O&K Trojan
RH8, RH9 -----------------------------------------------------------------------27
RH11, RH12 --------------------------------------------------------------------37
RH18, RH20 --------------------------------------------------------------------47
RH30C, RH30D, RH40C -----------------------------------------------------57
Samsung
SE210----------------------------------------------------------------------------27
SE280, SE350 ------------------------------------------------------------------37
SE450----------------------------------------------------------------------------47
VME
L160 -----------------------------------------------------------------------------27
L190B, L270B------------------------------------------------------------------37
L320, L480 ---------------------------------------------------------------------57
21 Series
1
1
adapter
adapter
EX5854-21
EX5849-21
3-3/4"
3-3/4"
1"
1-5/16"
4-1/2"
9-1/8"
30°
30°
12.9
14.4
part no.
EX27SYL
EX27VIP
EX27TVIP
EX27S6F
EX27SD
EX119-27
EX119-27V
EX360-27
EX1550-27
EX1551-27
EX5827-27
EX5850-27V
a
8"
7-3/4"
7-3/4"
8-3/4"
8"
1-5/8"
1-5/8"
2-1/2"
4-5/8"
4-5/8"
2"
2"
b
3-1/2"
1/4"
3-3/4"
6"
2"
5-13/16"
5-13/16"
2-3/8"
6"
6"
1-1/2"
1-9/16"
c
1-23/32"
1-23/32"
3-7/8"
3-7/8"
3-7/8"
9-7/8"
8-1/16"
d
1-5/16"
1-5/16"
4-3/4"
30°
30°
lb
9.4
8.4
16.9
18.0
10.5
18.2
18.2
17.0
28.8
29.1
27.1
19.0
part no.
EX37SYL
EX37VIP
EX37TVIP
EX37S7F
EX37S8F
EX37SD
EX129A-37
EX129A-37V
EX450-37
EX5824-37
EX1506-37
EX1507-37
EX5856-37V
a
9-1/2"
9-1/2"
9-1/2"
11"
11"
10-1/4"
2-1/2"
2-1/2"
3-1/8"
3"
4-5/8"
4-5/8"
4-7/8"
b
4-3/4"
1/4"
4-1/2"
7"
8"
2-1/4"
8-19/32"
8-19/32"
3"
2-1/16"
6"
6"
2-1/6"
c
2-1/2"
2-1/2"
5"
9-3/4"
3-7/8"
3-7/8"
9-3/4"
d
1-3/4"
1-3/4"
5-3/4"
30°
30°
lb
17.3
13.9
16.7
25.7
27.0
17.4
37.1
37.1
31.0
30.3
60.2
60.2
37.9
part no.
EX47SYL
EX47VIP
EX47TVIP
EX47TVIP
EX47SD
EX1829A-47
EX450-47
EX5857-47V
a
11"
11"
11"
12-5/8"
10-3/4"
3-1/8"
-
b
5"
3/8"
5-1/8"
9"
2-1/2"
2-9/16"
3"
2-5/8"
c
4-3/4"
5"
10-5/8"
d
30°
5-3/4"
30°
lb
24.8
22.7
25.8
34.7
25.9
46.4
37.0
57.0
27 Series
style
T
T
T
T
T
3
3
7
5
5
1
1
description
standard
tiger
twin tiger
6" flare
chisel
adapter
adapter
adapter
adapter
adapter
adapter
adapter
37 Series
style
T
T
T
T
T
T
3
3
7
1
6
6
1
description
standard
tiger
twin tiger
7' flare
8' flare
chisel
adapter
adapter
adapter
adapter
adapter
adapter
adapter
47 Series
style
T
T
T
T
T
2
7
1
description
standard
tiger
twin tiger
9' flare
chisel
adapter
adapter
adapter
57 Series
style
T
T
T
2
description
standard
tiger
twin
adapter
part no.
EX57SYL
EX57VIP
EX57TVIP
EX1856A-57V
a
13"
13-1/8"
13-1/8"
3-3/16"
b
6"
1/2"
6-3/4"
5-7/8"
c
-
d
-
11-3/4"
25°
lb
34.0
34.0
40.8
71.0
New Generation of Esco Systems: Super V™
The Super V pin, tooth, and adapter system more closely matches break-out
forces while reducing fuel consumption and machine maintenance.
Slimmer Profile; Matches Break-Out
Forces More Closely
Unique 1-Piece, Vertical Pin
The Super V tooth has a slimmer profile which
provides increased penetration. The tooth
twists a quarter turn onto the adapter and "butts
up" against the adapter nose to match breakout forces more closely.
The unique, 1-piece, vertical, drive-thru pin locks to the tooth ear for excellent point retention. It is
completely covered by the tooth ear to reduce wear and avoid pin walk. The 1-piece pin
provides easier changeover and less cost; it is reusable for 29 Series sizes and larger.
Various information can be determined from the part numbering system. Refer to the following
chart for basic part number information.
Part Number Explanations for Exco Super V™
Prefix
Suffix
Explanation
EV
S_F
Flare (_indicates width of flare.)
Note: The numbers
EV
SYL
Standard
Within the part number
EV
TVY
Twin Tiger
represent the "Series."
EV
VY
Tiger
Examples:
EV19SYL
19 Series Standard Tooth
EV51TVY
51 Series Twin Tiger Tooth
EV43S9F
43 Series 9" Flare Tooth
Special tools for Super V Adapters
For removal and installation of 29, 33, 39, 43 and 51 Series Super V teeth use special tool
EXPRT
New Generation of Esco Systems: Super V™
Standard Teeth (SYL Suffix)
(Centerline)
• For general-purpose-to-heavy-duty digging
conditions.
• Excellent penetration and wear.
Tiger Teeth (VY Suffix)
(Non-Centerline)
• High penetration for frost and tough
material.
Twin Tiger Teeth (TVY Suffix)
(Non-Centerline)
• For digging and loading in extremely tight
material.
• Use as a corner tooth with tiger teeth in the
center.
(Centerline)
• For digging in mud-like conditions
• Provides more bucket capacity by bridging
material between teeth.
Esco Super V™ Systems
Retainers
Illustrated parts
are actual size.
EV19PN
19 Series
EV23PN
23 Series
EV29PN
29 Series
EV33PN
33 Series
EV39PN
39 Series
EV43PN
43 Series
EV51PN
51 Series
Esco Super V™ System - Tooth by Series
19 Series
style
a
b
c
d
-
description
standard
tiger
twin tiger
flare
pin
adapter
part no.
EV19SYL
EV19VY
EV19TVY
EV19TF
EV19PN
EV5854-V19
disc.
ü
ü
ü
ü
ü
ü
used on
JD: 190E, 290D Competitive: Case: 488C, 590SL Caterpillar:
438B Komatsu: PC95, PC100-5 Liebherr: R310B, O&K:
MH2.10
23 Series
style
a
b
c
d
-
description
standard
tiger
twin tiger
flare
pin
adapter
part no.
EV23SYL
EV23VY
EV23TVY
EV23S5F
EV23PN
EV5849-V23
used on
ü
ü
ü
ü
ü
ü
JD: 490, 490D, 490E, 495D, 590D, 595, 595D Competitive:
Case: 688C: Caterpillar: 205B, 211B, E110B, E120B Kobelco:
SK100, SK120, SL150 Komatsu: PC120-6, PC150LC5 Liebherr:
R900Lit; Link-Belt: 2650, 2700
29 Series
style
a
b
c
d
-
description
standard
tiger
twin tiger
flare
pin
adapter
part no.
EV29SYL
EV29VY
EV29TVY
EV29S6F
EV29PN
EV5850-V29
used on
ü
ü
ü
ü
ü
ü
JD: 690, 690A, 690B, 690C, 690D, 690E, Competitive: Case:
883C, 9030, Caterpillar: 215D, 320L, E200B, Kobelco: SK200,
Komatsu: PC180LC5, PC200LC6, Liebherr: R902Lit, R912Lit,
O&K: RH CITY, RH5
33 Series
style
a
b
c
d
-
description
standard
tiger
twin tiger
flare
pin
adapter
part no.
EV33SYL
EV33VY
EV33TVY
EV33S7F
EV33PN
EV5855-V33
used on
ü
ü
ü
ü
ü
ü
JD: 790, 790D, 790E, 792, 792D, Competitive: Case: 1088C,
1188C, 9040, Caterpillar: 225D, 325L, E240B, E300B, Kobelco:
SK220, Komatsu PC220LC6, Liebherr: R922Lit, R923Lit, LinkBelt:: 3400, O&K: RH6-20
39 Series
style
a
b
c
d
-
description
standard
tiger
twin tiger
flare
pin
adapter
part no.
EV39SYL
EV39VY
EV39TVY
EV39S8F
EV39PN
EV5856-V39
used on
ü
ü
ü
ü
ü
ü
JD: 892D, 892E, Competitive: Case: 1288C, 9050, Caterpillar:
235B, 235C, 330L, Kobelco: SK300,
Komatsu PC300LC5, PC360LC3, Liebherr: R942Lit,
Link-Belt: 4300, O&K: RH12
43 Series
style
a
b
c
d
-
description
standard
tiger
twin tiger
flare
pin
adapter
part no.
EV43SYL
EV43VY
EV43TVY
EV43S9F
EV43PN
EV5856-V43
used on
ü
ü
ü
ü
ü
ü
JD: 922D, 992E, Competitive: Case: 9060, Caterpillar: 235D,
350L, Kobelco: SK400, Komatsu: PC400LC5, Liebherr:
R954Lit, Link-Belt: 5800, O&K: RH16, RH20
51 Series
style
a
b
c
-
description
standard
tiger
twin tiger
pin
adapter
part no.
EV51SYL
EV51VY
EV51TVY
EV51PN
EV5857A-V51
used on
ü
ü
ü
ü
ü
JD: 922D, 992E, Competitive: Caterpillar: 245D, Komatsu:
PC650LC3, Liebherr: R964Lit, O&K: RH25
Esco Super V™ System - Specifications
T
19 Series
style
T
T
T
T
1
description
standard
tiger
twin tiger
flare
adapter
part no.
EV19SYL
EV19VY
EV19TVY
EV19TF
EV5854-V19
a
6-1/2"
7"
7"
6-1/2"
1"
b
2-1/2"
7/16"
3"
4-1/2"
3-1/8"
c
6-1/2"
d
30°
nose angle
12°
lbs.
5.2
4.3
5.5
6
8.7
part no.
EV23SYL
EV23VY
EV23TVY
EV23S5F
EV5849-V23
a
7-1/2"
8"
8"
7-1/2"
1-1/8"
b
3"
1/2"
3-1/2"
5"
3-3/4"
c
7-1/2"
d
30°
nose angle lbs.
6.8
6.5
7.5
8.8
12°
14.5
part no.
EV29SYL
EV29VY
EV29TVY
EV29S6F
EV5850-V29
a
8-5/16"
9-9/16"
9-9/16"
9-1/6"
1-1/2"
b
3-1/2"
7/16"
4-1/8"
6"
4-1/2"
c
8-1/4"
d
30°
nose angle lbs.
10.7
8.7
9.6
13.7
10°
17.5
23 Series
style
T
T
T
T
1
description
standard
tiger
twin tiger
flare
adapter
29 Series
style
T
T
T
T
1
description
standard
tiger
twin tiger
flare
adapter
Esco Super V™ System - Specifications
33 Series
style
T
T
T
description
standard
tiger
twin tiger
T flare
1 adapter
part no.
EV33SYL
EV33VY
EV33TVY
a
9-1/8"
10-3/8"
10-3/8"
b
4"
1/2"
4-9/16"
c
-
d
-
nose angle lbs.
15
12.3
14.2
EV33S7F
EV5855-V33
10"
1-1'2"
7"
5"
9-1/4"
30°
part no.
EV39SYL
EV39VY
EV39TVY
EV39S8F
EV5856-V39
a
10-1/8"
11-11/16"
11-11/16"
11"
2"
b
c
4-3/4"
9/16"
5-1/8"
8"
5-3/4" 10-3/8"
d
30°
nose angle lbs.
21.5
17.5
19.9
23.3
36
10°
part no.
EV43SYL
EV43VY
EV43TVY
EV43S9F
EV5856-V43
a
11-1/4"
12-7/8"
12-7/8"
12-5/16"
2"
b
5"
5/8"
5-5/8"
9"
6"
d
30°
nose angle lbs.
29
23.5
27.4
38.5
10°
48
part no.
EV51SYL
EV51VY
EV51TVY
EV5857A-V51
a
12-1/8"
14"
14"
2-1/2"
b
c
5-1/2"
3/4"
6-1/4"
6-7/16" 11-7/8"
d
30°
nose angle lbs.
33
30
36
10°
63
10°
19.6
25
39 Series
style
T
T
T
T
1
description
standard
tiger
twin tiger
flare
adapter
43 Series
style
T
T
T
T
1
description
standard
tiger
twin tiger
flare
adapter
c
11"
51 Series
style
T
T
T
1
description
standard
tiger
twin tiger
adapter
John Deere Replacement Teeth for Hensley Products
John Deere replacement teeth for Hensley products come in sizes and tooth designs to fit almost all
machine makes and models.
The Parabolic (Dished-Out) Design Creates a Wedging, Self-Tightening Fit
With use, the parabolic (dished-out) design
mating system creates a wedging and selftightening fit. A dished-out area in the lower
top and bottom of the adapter nose plus a
recessed channel on the inside sidewall of the
tooth which matches a tapered extension on the
adapter nose piece forms a locking fit in all
directions and reduces tooth movement both
vertically and horizontally. The tooth and
adapter are designed as a bucket tooth system
that will absorb impact loads and generally
reduce the amount of abrasive action to the
bucket lip.
Flex Pin Retention
The TP400HD and TP475HD Flex Pins are
made of two hardened steel forgings with
vulcanized neoprene between them. Once
installed, the flex pin provides a four-way
locking support.
Removal is easy as pins can be driven through
the bottom of the adapter.
Hensley Series 350, 400 and 475 teeth use a
vertically-mounted flex pin.
Roll Pin Retention and Installation
The smaller series of John Deere replacement
teeth for Hensley products are retained with a
roll pin. The vertical design allows easy
removal and installation of center teeth. It is a
simple, economical, reliable means to retain
the tooth to the adapter.
These steel roll pins should always be installed
with the split facing towards the front of the
tooth.
Series 156, 160, 220, and 310 use a roll pin.
Steel Key
A steel key retains the 290, 330, 370 and 410
Series of John Deere replacement teeth for
Hensley products. This key provides
outstanding retention in all types of
applications. It is not reuseable.
CE98- 01U,02C Date
Various information can be determined from the part number system. Refer to the following chart for
basic part numbering information.
Part Number Explanation (Replacement Teeth for Hensley Products)
Prefix
Suffix
Explanation
TF
Fanggs Digging
TT
Tiger
TX
Standard
TX
AP
Abrasion Paneled
TX
F
Flare
TX
WT
Twin Tiger
Example:
Part Number TX400
Series 400 standard tooth.
Part Number TX400AP
Series 400 abrasion paneled tooth.
NOTE: The numbers within the part
number represent the “Series.”
John Deere Replacement Teeth for Hensley Products - Types Available
(TF__) (Non-Centerline)
• For general-purpose-to-heavy
digging.
• Provides a clean start and close
crowd.
Abrasion Paneled Teeth
(TX__AP) (Centerline)
• For loading and digging in
highly-abrasive material.
• Panel design makes tooth selfsharpening.
Flare Teeth
(TX__F) (Centerline)
• For digging in loose and mudlike conditions to improve the
bridging of material between
teeth.
• Provides flush cut or clean-up.
Standard Teeth
(TX__) (Centerline)
• For general-purpose to heavyduty applications.
• Provides long wear life.
Tiger Teeth
(TT__) (Non-Centerline)
• For digging and loading in
severe conditions - frost,
hardpan, extremely tight soil.
• Excellent penetration.
Twin Tiger Teeth
(TW__WT) (Non-Centerline)
• For digging and loading in
extremely tight material.
• Use as a corner tooth with tiger
teeth in center positions.
Hensley
2
Hensley - Teeth by Series
156 Series (Top Mount)
style
e
f
c
d
b
d
-
description
part no.
Fanggs
TF156
standard
TX156
tiger
TT156
twin tiger
TX156WT
tooth, star
PMS156
heavy-duty
PMS156HD
tiger h-d
PMT156HD
flare
PMX156F
heavy
PMX156H
extra long
PMX156LP
tooth, long
PMX156L
tooth, twin tiger long
PMX156WTL
pin
TF13P
pin
TP156
adapter
T834X156
adpt., ctr. (156 nose)
PM110HX
adpt., RH (156 nose)
PM110RH
adpt., LH (156 nose)
PM110LH
blade (156 nose)
PM11V16L
blade (156 nose)
PM11V16R
adpt., W-O, 1-1/2 leg, .625" lip 30 degrees
PM230X156
adpt., B-O, .81" thr., 29deg JCB 3C
PM300X156
adpt., B-O, LH, crnr., refer to 300X156
PM301X156
adpt., B-O, RH, crnr. refer to 300X156
PM302X156
adpt., B-O, Deere no. U-41344
PM344X156
adpt., B-O, 1-1/2 leg, .93" throat
PM350X156
adpt., B-O, 2 leg, step, Case #D35642
PM401X156
adpt., W-O, 1-1/2 leg, .625" lip
PM548X156
adpt., W-O, 1-1/2 leg, .875" lip
PM549X156
adpt., W-O, 1-1/2 leg, 1" lip
PM550X156
adpt., B-O, .625" throat, 21deg
PM551X156
adpt., W-O, 1-1/2 leg, .75"" lip
PM552X156
adpt., W-O, flush, .75"" to .875"
PM681X156
adpt., B-O, step (Drott TD-6)
PM682X156
adpt., B-O, 2 leg, 1.18" throat
PM683X156
adpt., B-O, 2 leg, .81" throat
PM684X156
adpt., W-O, bttm. leg, 1" lip
PM805X156
adpt., W-O, bttm. leg, .625" to .875", ditch wit PM835X156
adpt., W-O, bttm. leg, .75"" to 1.0" lip
PM836X156
12" lip blade w/3 noses
PM12M156-12A
PM14M156-12A
PM18M156-12A
PM24M156-12A
ripper box
PMB922B
box pin (B922B)
PMP922
pin removal tool for P100, P156
PMPRT156
pin punch
PM516PU
adapter, nose, W-O
PM156WN
rcv. disc.
non stock
9
9
9
9
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
N.S.
N.S.
N.S.
N.S.
N.S.
N.S.
N.S.
STK
STK
N.S.
STK
STK
N.S.
N.S.
N.S.
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
9
9
9
used on
JD: 300, 310D, 315D, 410D, 500B, 510, 510D, 710B,
Competitive: backhoes
style
e
f
c
d
b
-
Fanggs
description
part no.
TF160
standard
tiger
twin tiger
flare
star
heavy-duty
pin
adapter
adapter
adapter
adpt., B-O, 2 leg, .81" throat, (TCM 830)
adpt., B-O, RH, crnr.
adpt., B-O, LH, crnr.
adpt., B-O, 2 leg 1.125" throat
adpt., B-O, 2 leg, Cat #8J2930
adpt., B-O, 2 leg, Komatsu #1 13-70-22140
adpt., B-O, 1-1/2 leg, 1.31" throat (Clark 55C)
adpt., B-O, step
adpt., B-O, step
adpt., B-O, 2 leg, .90" throat, (KSS-65Z)
adpt., B-O, RH, crnr., refer to 650X160
adpt., B-O, step
adpt., B-O, H&L #L2145-23, L-4013-23
adpt., B-O, Case/Drott 4-in.-1, #26269
adpt., W-O, top leg, H&L #809-24
adpt., B-O, step
adpt., B-O, 1.18" throat, Deere U41344
adpt., W-O, bttm. Leg
ripper box
box pin (B926A)
pin punch
adpt. nose, W-O
TX160
TT160
TX160WT
TX160F
PMS160
PMX160HD
TP160
T658X160
PM552X160
PM850X160
PM168X160
PM169X160
PM170X160
PM204X160
PM309X160
PM310X160
PM314X160
PM504X160
PM510X160
PM553X160
PM650X160
PM653X160
PM654X160
PM702X160
PM706X160
PM717X160
PM718X160
PM750X160
PM775X160
PM787X160
PM792X160
PM809X160
PM840X160
PM861X160
PM927X160
PM928X160
PMB926A
PMP926
PM716PU
PM160WN
rcv. disc.
non stock
9
9
9
9
9
STK
STK
STK
STK
STK
N.S
STK
STK
STK
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
STK
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
STK
STK
STK
STK
9
9
used on
JD: 80, 110, 190E, 290D, Competitive: backhoes, excavators
162 Series (Side Mount)
style
c
f
b
d
-
description
tooth, tiger
standard
flare, 4"
heavy duty
twin tiger
pin
flex pin
adpt., B-O, 1.31" throat, 30 deg, Clark 55C
adpt., B-O, step
adpt., B-O, step
adpt., W-O, bttm. leg, 1" to 1.25"
adpt., B-O, 1.06" throat, (VME L-70)
adpt., B-O, LH, refer to 902X162
adpt., B-O, RH, refer to 902X163
blade (162 nose) - RH
blade (162 nose) - LH
adpt. nose, W-O
part no.
PMT162
PMX162
PMX162F
PMX162HD
PMX162WT
TP160
PMP162
PM314X162
PM510X162
PM702X162
PM750X162
PM850X162
PM901X162
PM902X162
PM903X162
PM904X162
PM927X162
PM13V16R
PM13V16L
PM162WN
rcv. disc.
9
non stock
STK
STK
STK
STK
N.S
STK
STK
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
STK
used on
style
e
f
c
d
b
a
a
-
description
rcv. disc.
non stock
TF220
TX220
TT220
TX220WT
TX220F
TX220AP
PMS220
PMX220ABR
PMX220DP
PMX220WTL
PMT220L
9
9
9
9
9
9
pin
TP160
adapter
T109X220
PM0C1X220
PM3C1X220
PM103X220
adpt., W-O, notched LH crnr.
PM107X220
adpt., W-O, notched RH crnr.
PM108X220
adpt., B-O, 1.125" throat, (D57S)
PM111X220
adpt., B-O, crnr., RH, 1.15 thr
PM112X220
adpt., B-O, crnr., LH, 1.15 thr
PM113X220
PM155X220
adpt., B-O, 2 leg, 1" throat
PM168X220
PM169X220
PM170X220
adpt., B-O, step, IH #610986C1
PM211X220
adpt., B-O, ctr. (920, 930, 941B)(1U0257)
PM257X220
adpt., B-O, crnr., Cat #3G4258
PM258X220
PM259X220
adpt., B-O, step, IH #611606C1(270, 442, 444)PM270X220
PM295X220
PM310X220
adpt., B-O, 1.18" thr, 30deg (Case 750, 850) PM311X220
adpt., B-O, 2 leg 1"" throat, 25deg, Kom D41 PM410X220
adpt., B-O, 1.31" thr, ESCO #4738-25 (W36) PM473X220
PM500X220
adpt., B-O, step, Cat #7J4415
PM613X220
adpt., stake-type (Poclain, PC8)
PM615X220
adpt., B-O, ctr. 1.06" throat (Case 621, 855D) PM621X220
adpt., B-O, crnr. (Case 621)
PM622X220
PM700X220
PM701X220
PM702X220
adpt., B-O, step (Wabco 222G)
PM703X220
adpt., B-O, step (Fiat-Allis 161)
PM706X220
PM707X220
adpt., B-O, step
PM710X220
adpt., B-O, 1.18" throat, (F-A 545B)
PM730X220
adpt., B-O, 1.09" throat, Case #D49545
PM747X220
adpt., B-O step
PM785X220
adpt., B-O step
PM786X220
adpt., B-O, 1-1/2 leg, 1.06" throat
PM796X220
PM797X220
adpt., W-O, 1-1/4 leg, 1.5" throat
PM809X220
PM810X220
PM811X220
PM812X220
adpt., B-O, 1.06" throat, (Case W18)
PM818X220
adpt., B-O, 1.31" throat
PM824X220
PM855X220
PM856X220
PM857X220
adpt., B-O, step, Deere #T38783
PM860X220
PM927X220
adpt. nose, W-O
PM220WN
9
9
STK
STK
STK
STK
STK
STK
N.S
STK
STK
STK
STK
STK
STK
N.S
N.S
STK
STK
STK
N.S
STK
STK
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
STK
STK
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
STK
Fanggs
standard
tiger
twin tiger
flare
abrasion paneled
star
abrasion
down pitch
twin tiger long
tooth, tiger long
part no.
used on
225 Series
style
c
f
a
a
b
-
description
tiger
std.
abr. paneled
abr.
flare, 4.5""
twin tiger
flex pin
adpt., B-O, rev., crnr., Deere #112163
adpt., B-O, ctr., .81" throat
adpt., B-O, ctr., 1.06" throat
adpt., B-O, crnr. (544E, 624E)
adpt., B-O, LH, crnr., Cat #3G4258
adpt., B-O, RH, crnr., Cat #3G4259
adpt., B-O, 1.43" thr, 22deg, Clark #251 147
adpt., B-O, 1.56" thr, 33deg, Deere T35385
adpt., B-O, 1.31" throat, 22deg (Case W36)
adpt., B-O, 1.31" throat, Deere T29886
adpt., B-O, step
adpt., B-O, 1.31", Case #L58824
adpt., W-O, bttm. leg, 2" to 2.25" lip
adpt., W-O, flush, 1.25" lip, 2"
adpt., nose, W-O
part no.
PMT225
PMX225
PMX225AP
PMX225ABR
PMX225F
PMX225WT
PMP225
PM0C1X225
PM102X225
PM106X225
PM111X225
PM155X225
PM163X225
PM164X225
PM165X225
PM191X225
PM257X225
PM258X225
PM259X225
PM310X225
PM313X225
PM385X225
PM473X225
PM544X225
PM785X225
PM572X225
PM611X225
PM703X225
PM747X225
PM796X225
PM797X225
PM810X225
PM811X225
PM818X225
PM824X225
PM855X225
PM857X225
PM860X225
PM900X225
PM902X225
PM903X225
PM904X225
PM225WN
rcv. disc.
non stock
STK
STK
N.S
N.S
N.S
N.S
STK
N.S
N.S
N.S
N.S
N.S
N.S
N.S
STK
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
STK
used on
style
e
f
c
d
b
a
a
Fanggs
description
part no.
TF290
standard
tiger
twin tiger
flare
abrasion panel
abrasion
pin
flex pin
adapter
adapter
adapter
adapter
adapter
adapter
adapter
adapter
adapter
nose template kit for 290, 330
nose rebuild kit for 290 series
flex pin, C-19 lips (136X290)
flex pin, solid rubber
pin removal tool for (290, 330)
tooth, sharp, ribbed
adpt., stake type, ESCO C-19 lip
adpt., W-O, 1-1/2 leg, RH, 1.75"
adpt., W-O, 1-1/2 leg, LH, 1.75"
adpt., stake type, Hensley C-19
adpt., B-O, 2 leg, 1.25" thr.
adpt., B-O LH crnr. (955L)
adpt., B-O RH crnr. (955L)
adpt., B-O, 2 leg, 1.31" thr. 23deg, (955L)
adpt., B-O, 2 leg, 1.93" thr. 23deg, (85Z11)
adpt., B-O, LH (85Zll), (req. 486INS)
adpt., B-O, RH (85Zll), (req. 486INS)
adpt., B-O, LH (80Zlll)
adpt., B-O, RH (80Zlll)
adpt., B-O, 2 leg, 1.03" thr. (80ZIII)
adpt., W-O, 1-1/2 leg, 1.375" lip
adpt., stake type (Akerman H9, H11)
adpt., B-O, ctr., 1.375" thr.
adpt., B-O, ctr., 1.31" thr. (Case 821)
adpt., B-O, Crnr (VME L-140)
adpt. nose, W-O
TX290
TT290
TX290WT
TX290F
TX290AP
PMX290ABR
TK290
PMP290
T127X290
T158X290
PM125X290
PM150X290
PM190X290
PM191X290
PM673X290
PM674X290
PM822X290
PMA-TEM
PMA290NR
PMP136
PMP290STP
PMPRT290
PMX290SYL
PM119X290
PM124X290
PM130X290
PM131X290
PM136X290
PM156X290
PM308X290
PM309X290
PM383X290
PM430X290
PM480X290
PM486X290
PM487X290
PM488X290
PM489X290
PM490X290
PM580X290
PM589X290
PM721X290
PM722X290
PM820X290
PM821X290
PM904X290
PM905X290
PM290WN
rcv. disc.
non stock
9
9
9
9
9
9
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
N.S
N.S
STK
STK
N.S
N.S
N.S
STK
STK
STK
STK
STK
STK
N.S
N.S
N.S
N.S
STK
N.S
N.S
N.S
N.S
N.S
STK
STK
STK
N.S
N.S
N.S
N.S
N.S
STK
STK
STK
N.S
N.S
N.S
STK
9
9
9
used on
JD: 490, 490D, 490E, 495D, 590D, 595, 595D, 120, 160LC,
Competitive: excavators
style
f
c
d
a
b
description
standard
tiger
twin tiger
abrasion panel
tooth, short, ribbed
flare
steel pin
part no.
PM295
PMT295
PM295WT
PM295AP
PM295SYL
PM295F
PMP295
pin, steel spring
adpt. 1-1/4" lip
adpt., C-19 cast lip
adpt. 1-1/2" lip
adpt. B-O L.H.
adpt., B-O R.H.
adpt. bttm. leg W-O
adpt., B-O
adpt., stake type, Akerman H7
pin removal tool for P295SL
adpt., W-O nose
PMP295SL
PM127X295
PM136X295
PM158X295
PM308X295
PM309X295
PM383X295
PM430X295
PM589X295
PMP295SLRT
PM295WN
rcv. disc.
non stock
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
N.S
N.S
N.S
N.S
STK
STK
STK
used on
style
c
f
a
a
b
d
description
tiger
standard
abrasion
abrasion panel
flare, 6""
heavy duty rock
twin tiger
flex pin (4 tab)
adpt. nose, W-O
part no.
PMT300
PMX300
PMX300ABR
PMX300AP
PMX300F
PMX300R
PMX300WT
PMP300B
PM300WN
rcv. disc.
non stock
STK
STK
N.S
N.S
N.S
N.S
N.S
STK
STK
used on
style
e
Fanggs
pin
description
part no.
TF310
TP160L
f
c
d
b
a
a
standard
tiger
twin tiger
flare
tooth, 4" wide
abrasion paneled
abrasion
pin
flex pin, C-19 lip (136X310)
adapter
TX310
TT310
TX310WT
TX310F
PMX310-4
TX310AP
PM310ABR
TP160
PMP136
T153X310
key
refer also to PM142X330
adpt., W-O, flush, 1.25" lip
adpt., W-O, 1-1/2 leg, 1.25" lip
adpt., W-O, 1-1/2 leg, 1.25" lip
adpt., W-O, RH, 1-1/2 leg, 1.75"
adpt., stake-type, C-19 lip (reqs P136)
adpt., flush, 1.5" str. lip
adpt., RH, flush, 1.5" sp. lip
adpt., LH flush, 1.5" sp. lip
adpt., W-O, RH, 1-1/2 leg, 1.5" lip
adpt., W-O, LH, 1-1/2 leg, 1.5" lip
adpt., W-O, 1-1/2 leg, 1.5" lip
adpt., W-O, LH, notched crnr.
adpt., W-O, RH, notched crnr.
adpt., B-O, 1.46" thr. Komatsu D65, D75
adpt., B-O, LH crnr. (955L)
adpt., B-O, RH crnr. (955L)
adpt., B-O, 1.31" thr., 22deg, Case 1450
adpt., B-O, specialty item
adpt., B-O, step
adpt., B-O, 2 leg, 1.81" thr, Furukawa 320A
adpt., W-O, 1-1/2 leg, 1.375" lip
adpt., stake-type (req. K668)
adpt., B-O, 1-1/2 leg, 1.375" thr
adpt., B-O, step
adpt., B-O, step
adpt., B-O, step
adpt., B-O
adpt., W-O, bttm. leg, .75" to .875" Lip
adpt., W-O, 1.375" special lip
adpt., B-O, 2 leg, 1.81" thr. (HD 6G, 12G)
adpt., W-O, flush, 1.5" str. lip
adpt., W-O, flush, LH, sp. lip
adpt., W-O, flush, RH, sp. lip
adpt. nose, W-O
PMK668
PM110X310
PM119X310
PM122X310
PM124X310
PM125X310
PM127X310
PM128X310
PM130X310
PM136X310
PM138X310
PM150X310
PM151X310
PM152X310
PM154X310
PM155X310
PM156X310
PM158X310
PM159X310
PM160X310
PM168X310
PM169X310
PM170X310
PM181X310
PM185X310
PM301X310
PM308X310
PM309X310
PM317X310
PM323X310
PM383X310
PM430X310
PM494X310
PM495X310
PM550X310
PM580X310
PM668X310
PM742X310
PM756X310
PM758X310
PM759X310
PM812X310
PM822X310
PM844X310
PM845X310
PM859X310
PM900X310
PM901X310
PM902X310
PM310WN
rcv. disc.
non stock
9
9
9
9
9
9
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
STK
N.S
N.S
N.S
N.S
N.S
N.S
N.S
STK
STK
STK
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
STK
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
N.S
STK
N.S
N.S
N.S
N.S
N.S
N.S
STK
9
9
9
used on
JD: 160LC, 200LC, 230LC, 270LC, 590D, 595, 595D, 690, 690A,
690B, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D,
Competitive: excavators, loaders
style
e
f
c
d
b
a
a
Fanggs
description
part no.
TF330
standard
tiger
twin tiger
flare
abrasion panel
sharp, ribbed
short rock
abrasion
pin
flex pin
adapter
adapter
adapter
adapter
adapter
adapter
nose rebuild kit for 330 Series
lip fastener, C-19 lips (136X330, 136X310)
lip fastener, C-29 lips (236X330)
steel wedge
adpt., W-O, 1-1/2 leg, 1.625" lip
adpt., B-O specialty item (Sauerman)
adpt., W-O, bttm. leg, 1.25"lip, 23deg
adpt., B-O, ctr. (VME L150, L180)
adpt., B-O, ctr. (Case 921)
adpt. nose, W-O
TX330
TT330
TX330WT
TX330F
TX330AP
PMX330SYL
PMX330SR
PMX330ABR
TK330
PMP330
T158X330
PM190X330
PM743X330
PM744X330
PM822X330
PM937X330
PMA330NR
PMP136
PMP236
PMW330
PM136X330
PM159X330
PM160X330
PM225X330
PM236X330
PM323X330
PM383X330
PM901X330
PM921X330
PM935X330
PM936X330
PM330WN
rcv. disc.
non stock
9
9
9
9
9
9
STK
STK
STK
STK
STK
STK
STK
N.S
STK
STK
STK
STK
N.S
N.S
N.S
N.S
STK
STK
STK
STK
STK
STK
STK
STK
N.S
N.S
STK
N.S
N.S
N.S
STK
STK
STK
9
9
used on
JD: 160LC, 200LC, 230LC, 270LC, 590D, 595, 595D, 690, 690A,
690B, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D,
style
f
a
b
c
d
description
part no.
standard
abrasion panel
flare
short, ribbed
tiger tooth
twin tiger tooth
steel pin
PM335
PM335AP
PM335F
PM335SYL
PMT335
PM335WT
PMP335
pin, steel spring
adpt., 1.5" lip
adpt., W-O, flush 1.625" - 1.75" lip, 30 deg
adpt., C-29 Hensley cast lip
adpt., stake (Akerman H12, 14, 16)
adpt., L.H. crnr., 1.75" lip
adpt., R.H. crnr. 1.75" lip
adpt., 1.75" lip
adpt., W-O nose
PMP335SL
PM158X335
PM190X335
PM236X335
PM355X335
PM935X335
PM936X335
PM937X335
PMP335SLRT
PM335WN
rcv. disc.
non stock
used on
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
style
f
c
a
b
d
description
standard
tiger
abr. paneled, short
flare
twin tiger
pin
adpt. nose, W-O
part no.
TX350
PMT350
PMX350APS
PMX350F
PMX350WT
TP400HD
PM350WN
rcv. disc.
non stock
9
STK
STK
N.S
N.S
STK
STK
STK
9
used on
style
e
f
c
d
a
b
a
Fanggs
description
part no.
TF370
standard
tiger
twin tiger
abrasion paneled
flare
sharp, ribbed
abrasion
steel keeper
TX370
TT370
TX370WT
PMX370AP
PMX370F
PM X370SYL
PMX370ABR
TK370
flex pin, front lock
pin removal tool for (370, 410, 450)
fastener for Hensley C-29 lips
adpt., W-O, 1.5" lip
adpt. W-O, ctr., 2" lip
adpt., W-O, RH/LH, 1.75" sp. lip
adpt., W-O, ctr., 1.75" str. lip
adpt., W-O, LH, 2" flush sp. lip
adpt., W-O, RH, 2" flush, sp. lip
adpt., W-O, ctr., 2" flush, str. lip
adpt. nose rebuild kit for 370 Series
adpt. nose, W-O
PMP370FL
PMPRT370
PMP236
PM129X370
PM158X370
PM236X370
PM827X370
T940X370
PM936X370
PM937X370
PM947X370
PM948X370
PM949X370
PMA370NR
PM370WN
rcv. disc.
non stock
9
9
9
9
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
N.S
N.S
N.S
N.S
STK
N.S
STK
STK
STK
STK
STK
STK
9
9
used on
JD: 230LC, 270LC, 330LC, 370
style
e
b
c
d
standard
flare
sharp, ribbed
tiger
twin tiger
pin, steel
pin, steel spring
description
part no.
PM385
PM385F
PM385SYL
PMT385
PM385WT
PMP385
PMP385SL
adpt., stake type, Hensley C29
adpt., W-O, bttm. leg
adpt., W-O, 1-1/2 leg, 1.75" lip
adpt., W-O, flush, 2" lip
adpt., W-O nose
PM236X385
PM355X385
PM827X385
PM937X385
PM940X385
PM949X385
PMP385LRT
PM385WN
rcv. disc.
non stock
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
used on
style
e
f
c
d
b
a
a
a
Fanggs
description
part no.
TF400
standard
tiger
twin tiger
flare
abrasion paneled
abrasion
abrasion heavy
short
long sharp
penetrator narrow
pin
slag pin
slag pin
slag pin
wedge key
adapter
adapter
adpt., W-O, 1-1/2 leg, 1.5" lip
adpt., W-O, 2 leg, ctr., 2" lip
adpt., W-O, notched crnr., LH
adpt., W-O, notched crnr., RH
adpt. nose, W-O
TX400
TT400
TX400WT
TX400F
TX400AP
PMX400ABR
PMX400ABRB
PMX400H
PMX400LS
PMX400SD
TP400HD
TP400SA
TP400SB-S
PMP400SB-OS
PMK129C
T802X400
PM800X400
PM129X400
PM236X400
PM604X400
PM827X400
PM830X400
PM831X400
PM832X400
PM938X400
PM940X400
PM945X400
PMA410NR
PM400WN
rcv. disc.
non stock
9
9
9
9
9
9
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
N.S
N.S
STK
STK
N.S
N.S
N.S
N.S
STK
N.S
N.S
STK
STK
9
9
used on
JD: 200LC, 230LC, 270LC, 330LC, 370, 450LC, 690, 690A, 690B,
690C, 690D, 690E, 790, 790D, 790E, 792, 792D, 890, 890A,
892D, 892E, 992D, 992E, Competitive: excavators, loaders
style
e
f
d
c
a
a
b
Fanggs
description
part no.
TF410
standard
twin tiger
tiger
abrasion
abrasion paneled
flare
long, sharp
sharp, ribbed
steel keeper
adpt. W-O, 1-1/2 leg, 2" lip
TX410
TX410WT
TT410
PMX410ABR
PMX410AP
PMX410F
PMX410LS
PMX410SYL
TK410
T940X410
adpt., stake type Hensley C-29
adpt., W-O, 2 leg, 2" str. lip
adpt., W-O, 2 leg, 2" sp. lip
adapt., W-O bttm. leg
adpt., W-O 1-1/2 leg 1.75" lip
adpt. nose, W-O
PM236X410
PMA464X410
PMA465X410
PMA466X410
PM827X410
PM890X410
PM937X410
PM410WN
rcv. disc.
9
9
9
9
9
9
non stock
used on
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
JD: 230LC, 270LC, 330LC, 370, 450LC
STK
N.S
N.S
N.S
N.S
N.S
N.S
N.S
STK
style
description
c tiger
f standard
a flare
abrasion
abrasion paneled
d twin tiger
adpt. nose, W-O
part no.
PMT450
PMX450
PMX450F
PMX450ABR
PMX450AP
PMX450WT
PM450WN
rcv. disc.
non stock
STK
STK
N.S
STK
STK
STK
STK
used on
part no.
TF475
rcv. disc.
non stock
used on
Fanggs
standard
tiger
twin tiger
flare
abrasion paneled
abrasion
slag heavy
slag long
slag h-bottom
TX475
TT475
TX475WT
TX475F
TX475AP
PMX475ABR
PMX475AH
PMX475AHL
PMX475AHS
9
9
9
9
9
9
STK
STK
STK
STK
STK
STK
N.S
N.S
N.S
STK
style
a
f
c
d
b
a
a
description
long heavy
slag
tiger long
twin tiger long
pin
adapter
adapter
adpt. nose, W-O
PMX475LP
PMX475S
PMT475L
PMX475WTL
TP475HD
T303X475
PM988X475
PM475WN
9
9
N.S
STK
STK
STK
STK
STK
STK
STK
JD: 270LC, 330LC, 450LC, 890, 890A, 892D, 892E, 992D, 922E,
Competitive: excavators, loaders
style
f
description
standard
abrasion panel
ribbed sharp
tiger
twin tiger
steel key pin
adapter
part no.
TX500
TX500AP
TX500SYL
TT500
TX500WT
TK500R
T806X500
rcv. disc.
non stock
9
9
9
STK
STK
STK
9
9
STK
STK
rcv. disc.
non stock
9
STK
9
9
STK
STK
used on
JD: 550LC, 600CLC, 750, 800C
style
description
ribbed sharp
tiger
twin tiger
steel key pin
adapter
part no.
TX550SYL
TT550
TX550WT
TK550R
T806X550
used on
JD: 600CLC, 750, 800C
Sidecutters
style
description
strikeoff sidecutter, 3/1 pattern
blade-type, 3/1 pattern
sidecutter, blade-type, RH, 2/2
sidecutter, blade-type, LH, 2/2
sidecutter, B-O, tooth-type, LH
sidecutter, B-O, tooth-type, RH
sidecutter, tooth-type, RH
sidecutter, tooth-type, LH
part no.
rcv. disc.
PMSCB220-SO
PMSCB330-SO
PMSCB410-SO
PMB311LH
PMB312RH
PMB330RH
PMB331LH
PMB102RH
PMB103LH
PM330X310
PM331X310
PM102X400
PM103X400
non stock
used on
STK
STK
STK
STK
STK
STK
STK
STK
STK
N.S
N.S
N.S
N.S
Hensley Attachments
style
description
part no.
one-piece tooth, B-O
PM099HX
tooth, ctr., long, early style
PM50CHX
tooth, LH. long, early style
PM50LH
tooth, RH. long, early style
PM50RH
tooth, ctr.
PM100CHX
tooth, ctr.
PM1020HX
tooth, ctr., short
PM500CHX
tooth, LH
PM100LH
tooth, RH
PM100RH
tooth, LH, short
PM500LH
tooth, RH, short
PM500RH
tooth, ctr.
PM1000HX
tooth, LH
PM1000LH
tooth, RH
PM1000RH
tooth, ctr., continuous edge
PM3000HX
continuous edge ctr. tooth
PM4330CHX
continuous edge W-O nose
PM4330WN
closed lifting eye, large I.D., 10-20,000 lb. excaPM1025HX
crnr. gusset
PMCG6
crnr. gusset
PMCG9
crnr. gusset
PMCG12
closed eye lifting hook
PM1030HHX
PM2060HHX
PM60100HX
tooth, LH
PM3000LH
tooth, RH
PM3000RH
tooth, ctr., heavy
PM3000H
tooth, LH, heavy
PM3000HLH
tooth, RH, heavy
PM3000HRH
tooth, ctr. (round & T bucket)
PM3000RC
blade (156 nose)
PM11V16L
blade (156 nose)
PM11V16R
blade (162 nose)
PM13V16L
blade (162 nose)
PM13V16R
roll pin (2.25")
PMP100
roll pin
PM301P
roll pin
PM1000P
pin
PM9J2358P
PM110HX
PM110LH
PM110RH
adpt., ctr. (parabolic 400 nose)
PM510HX
adpt., LH (parabolic 400 nose)
PM510LH
adpt., RH (parabolic 400 nose)
PM510RH
adpt., ctr.
PM1010HX
adpt., LH
PM1010LH
adpt., RH
PM1010RH
adpt., ctr., continuous edge
PM3010HX
adpt., LH, continuous edge
PM3010LH
adpt., RH, continuous edge
PM3010RH
adpt., ctr. (round & T bucket)
PM3010RC
adpt., RH/LH (round & T bucket), less W-O nos PM3010RRL
nose, W-O, ctr.
PM1010WN
nose, W-O LH
PM1010WNL
nose, W-O, RH
PM1010WNR
nose, W-O
PM9J4354WN
rcv. disc.
non stock
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
N.S.
STK
STK
STK
STK
STK
STK
STK
STK
N.S.
N.S.
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
used on
adpt. nose, W-O
PM156WN
nose, W-O
PM220WN
nose, W-O, LH (round & T bucket), ref. 3010RRPM3010LWN
nose, W-O, ctr., (round & T bucket)
PM3010WNRC
nose, W-O, RH (round & T bucket), ref. 3010RRPM3010RWN
nose, W-O, ctr.
PM1030WN
nose, W-O, ctr., continuous edge
PM3010WN
nose, W-O, LH, continuous edge
PM3010WNL
nose, W-O, RH, continuous edge
PM3010WNR
washer (old #3G9549W)
PM6Y9459W
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
Hensley Ripper Teeth - Applications
156 Series
style
c
b
description
rcv. disc.
non stock
9
9
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
rcv. disc.
non stock
9
9
STK
STK
N.S.
STK
STK
STK
STK
STK
STK
STK
STK
STK
part no.
PM 922X162
PM 926X162
rcv. disc.
non stock
STK
STK
used on
description
part no.
PMT501
PM501HX
PMB944
PMB977
PMP944
PM501P
PMP977
PM944-501
PM977-501
PM501WN
rcv. disc.
non stock
STK
STK
STK
STK
STK
STK
STK
STK
STK
STK
used on
description
tiger tooth
tiger tooth, long
twin tiger tooth
twin tiger tooth, long
std. tooth
flex pin
ripper sh., 28" (B977)
adpt. nose, W-O
part no.
PMT702
PMT702L
PMX702WT
PMX702WTL
PM702HX
PM702P
PM977-702
PM977-702L
PM702WN
rcv. disc.
non stock
STK
STK
STK
STK
STK
STK
STK
STK
STK
used on
tiger
long
star
heavy duty star
tiger, heavy duty
flare, 4.375
heavy
extra long
roll pin
box pin (B922B)
ripper box
ripper sh. (B922B)
pin removal tool for P100, P156
nose, W-O
part no.
TT156
TX156
PMS156
PMS156HD
PMT156HD
PMX156F
PMX156H
PMX156LP
PM156
PM922
PMB922B
PM922X156
PMPRT156
PM156WN
used on
160 Series
style
description
part no.
tooth, tiger
TT160
tooth, std.
TX160
tooth, star
PMS160
tooth, heavy duty
PMX160HD
adpt., B-O, 1-1/2 leg, 1.18 throat, 33 degrees ( PM552X160
adpt., W-O, bottom leg, 1-1 1/4 edge, 30 degrePM850X160
roll pin
PM160
box pin (B926A)
PM926
ripper box
PMB926A
ripper sh. (B922B)
PM922X160
ripper sh. (B926A)
PM926X160
pin removal tool for P160
PMRT160
used on
162 Series
style
description
box ripper sh. (B922B)
box ripper sh. (B926A)
501 Series
style
teeth, tiger
teeth, std.
ripper box
ripper box
box pin (B944)
flex pin (tooth)
box pin (B977)
ripper sh. (B944)
ripper sh. (B977)
adpt. nose, W-O
702 Series
style
Hensley - Specifications
Ty
pe
Type 1
Type 2
T
Type 3
style
T
T
T
T
T
T
T
T
T
T
T
T
description
Fanggs
standard
tiger
twin tiger
tooth, star
star h-d
tiger h-d
flare
heavy
extra long
tooth, long
tooth, twin tiger long
adpt., nose, W-O
blade (156 nose)
blade (156 nose)
adpt., W-O, 1-1/2 leg, .625" lip
adpt., B-O, .81" thr., 29deg JCB 3C
adpt., B-O, RH, crnr. refer to 300X156
adpt., B-O, Deere no. U-41344
adpt., B-O, 2 leg, step, Case #D35642
adpt., W-O, 1-1/2 leg, .625" lip
adpt., W-O, 1-1/2 leg, .875" lip
adpt., B-O, .625" throat, 21deg
adpt., W-O, 1-1/2 leg, .75"" lip
adpt., W-O, flush, .75"" to .875"
adpt., B-O, step (drott TD-6)
adpt., W-O, bttm. leg, .625" to .875", ditch wit
adpt., W-O, bttm. leg, .75"" to 1.0" lip
ripper box
nose weld-on
part no.
TF156
TX156
TT156
TX156WT
PMS156
PMS156HD
PMT156HD
PMX156F
PMX156H
PM156XLP
PMX156L
PMX156WTL
PM110HX
PM110RH
PM110LH
PM156WN
PM11V16L
PM11V16R
PM230X156
PM300X156
PM301X156
PM302X156
PM344X156
PM350X156
PM401X156
PM548X156
PM549X156
PM550X156
PM551X156
PM552X156
PM681X156
PM682X156
PM683X156
PM684X156
PM805X156
PM835X156
PM836X156
PM12M156-12AHX
PM14M156-12AHX
PM18M156-12AHX
PM24M156-12AHX
PMB922B
PM156WN
a
6"
4-1/4"
6-1/4"
6"
6"
6-1/16"
6-1/4"
5"
5-1/2"
6"
b
1-3/4"
1-3/4"
1/8"
3-1/8"
1-1/8"
1-1/8"
point
4-3/8"
2
2-1/4"
3-1/4"
2-1/4"
c
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
d
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
lbs.
3.9
1.3
1.8
3.3
2.4
2.7
2.1
2.8
2.6
3.6
1.7
2.5
8.2
5.9
6.1
1.8
23.0
23.0
3.7
4.9
10.0
10.0
6.5
6.6
6.6
4.0
4.0
4.7
6.0
5.4
4.2
6.2
6.4
4.0
4.0
3.5
5.0
29.8
32.0
44.3
57.0
14.7
1.8
style
T
T
T
T
T
T
T
2
Fanggs
standard
tiger
description
part no.
TF160
TX160
TT160
a
6-1/4"
6-7/8"
8-3/4"
b
2-1/8"
2-1/4"
1/4"
3-5/8"
6-5/8"
1"
2-5/16"
4-3/8"
c
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-1/16"
d
2-3/8"
2-3/8"
2-3/8"
2-3/8"
2-3/8"
2-3/8"
2-3/8"
30°
twin tiger
flare
star
std h.d.
adapter
adapter
adapter
adpt., B-O, 2 leg, .81" throat, (TCM 830)
adpt., B-O, 2 leg 1.125" throat
adpt., B-O, 2 leg, Cat #8J2930
adpt., B-O, 2 leg, Komatsu #1 13-70-22140
adpt., B-O, 1-1/2 leg, 1.31" throat (Clark 55C)
adpt., B-O, step
adpt., B-O, step
adpt., B-O, 2 leg, .90" throat, (KSS-65Z)
adpt., B-O, step
adpt., B-O, H&L #L2145-23, L-4013-23
adpt., W-O, top leg, H&L #809-24
adpt., B-O, step
adpt., B-O, 1.18" throat, Deere U41344
adpt., W-O, bttm. Leg
ripper box
adpt. nose, W-O
TX160WT
TX160F
PMS160
PMX160HD
T658X160
PM552X160
PM850X160
PM168X160
PM169X160
PM170X160
PM204X160
PM309X160
PM310X160
PM314X160
PM504X160
PM510X160
PM553X160
PM650X160
PM653X160
PM654X160
PM702X160
PM706X160
PM717X160
PM718X160
PM750X160
PM775X160
PM787X160
PM792X160
PM809X160
PM840X160
PM861X160
PM927X160
PM928X160
PMB926A
PM160WN
8-3/8"
4-1/2"
7-3/4"
6-5/8"
8"
6"
5-1/2"
1-1/4"
30°
lbs.
4.2
4.7
5.3
7.4
5.8
4.4
4.5
15.7
11.4
7.5
9.7
10.4
10.4
13.6
16.0
9.2
16.2
11.8
12.7
10.5
11.6
22.0
22.0
14.7
12.0
10.2
14.6
9.5
7.9
15.3
11.5
8.0
10.8
9.6
12.0
10.0
58.7
4.2
style
T
T
T
T
T
description
tooth, tiger
tooth, std.
tooth, flare, 4"
tooth, heavy duty
tooth, twin tiger
adpt., B-O, 1.31" throat, 30 deg, Clark 55C
adpt., B-O, step
adpt., B-O, step
blade (162 nose)
blade (162 nose)
adpt. nose, W-O
part no.
PMT162
PMX162
PMX162F
PMX162HD
PMX162WT
PM314X162
PM510X162
PM702X162
PM750X162
PM850X162
PM901X162
PM902X162
PM903X162
PM904X162
PM927X162
PM13V16R
PM13V16L
PM162WN
a
b
c
d
lbs.
4.7
3.5
4.2
4.2
7.2
16.2
12.7
14.7
10.0
7.5
17.1
15.9
24.1
24.2
12.0
26.6
26.6
4.5
style
T
T
T
T
T
T
T
T
T
T
T
T
2
Fanggs
standard
tiger
twin tiger
description
part no.
TF220
TX220
TT220
TX220WT
a
7"
7-1/8"
8"
8"
b
2-5/8"
2-3/4"
1/4"
3-7/8"
flare
abrasion paneled
nose weld-on
star
abrasion
down pitch
twin tiger
tooth, tiger long
adapter
adapter
adapter
adapter
adapter
adapter
adapter
adapter
adpt., W-O, notched LH crnr.
adpt., W-O, notched RH crnr.
adpt., B-O, 1.125" throat, (D57S)
adpt., B-O, crnr., RH, 1.15 thr
adpt., B-O, crnr., LH, 1.15 thr
adpt., B-O, step, IH #610986C1
adpt., B-O, ctr. (920, 930, 941B)(1U0257)
adpt., B-O, step, IH #611606C1(270, 442, 444)
adpt., B-O, 1.18" thr, 30deg (Case 750, 850)
adpt., B-O, 2 leg 1"" throat, 25deg, Kom D41
adpt., B-O, 1.31" thr, ESCO #4738-25 (W36)
adpt., B-O, step, Cat #7J4415
adpt., stake-type (Poclain, PC8)
adpt., B-O, ctr. 1.06" throat (Case 621, 855D)
adpt., B-O, step (Fiat-Allis 161)
adpt., B-O, step
adpt., B-O, 1.18" throat, (F-A 545B)
adpt., B-O, 1.09" throat, Case #D49545
adpt., B-O step
adpt., B-O step
TX220F
TX220AP
PM220WN
PMS220
PMX220ABR
PMX220DP
PMX220WTL
PMT220L
T109X220
PM100X220
PM106X220
PM102X220
PM385X220
PM544X220
PM611X220
PM900X220
PM0C1X220
PM3C1X220
PM103X220
PM107X220
PM108X220
PM111X220
PM112X220
PM113X220
PM155X220
PM168X220
PM169X220
PM170X220
PM211X220
PM257X220
PM258X220
PM259X220
PM270X220
PM295X220
PM310X220
PM311X220
PM410X220
PM473X220
PM500X220
PM613X220
PM615X220
PM621X220
PM622X220
PM700X220
PM701X220
PM702X220
PM703X220
PM706X220
PM707X220
PM710X220
PM730X220
PM747X220
PM785X220
PM786X220
PM796X220
7-1/2"
8"
4-7/8"
8-1/4"
8"
4-5/8"
3-1/2"
3 back
1-1/2"
3-3/8"
8-3/8"
c
2-1/4"
2-1/4"
2-1/4"
2-1/4"
2-1/4"
2-1/4"
4-1/8"
2-1/4"
2-1/4"
2-1/4"
2-1/4"
d
2-1/8"
2-1/8"
2-1/8"
2-1/8"
2-1/8"
2-1/8"
3-1/8 height
2-1/8"
2-1/8"
2-1/8"
2-1/8"
6"
9-1/2"
9-1/2"
8-1/2"
1-5/16"
8-1/2"
4-1/2"
7-1/4"
1"
1"
1-1/4"
30°
30°
25°
36°
8-7/8"
8-1/2"
1-1/4"
23°
lbs.
6.0
6.7
6.0
7.5
6.9
8.8
5.5
6.4
10.6
7.2
7.2
6.4
15.7
15.8
16.4
11.5
17.1
16.2
15.0
12.8
21.2
17.5
15.9
11.5
11.5
22.6
19.8
19.8
21.7
16.3
17.3
17.3
17.7
18.2
26.0
26.0
19.1
21.0
24.1
13.2
15.8
14.4
22.4
19.8
10.3
17.8
25.0
17.8
30.0
30.0
18.7
15.4
19.8
15.4
17.8
16.2
19.7
19.0
18.7
adpt., W-O, 1-1/4 leg, 1.5" throat
adpt., B-O, 1.06" throat, (Case W18)
adpt. nose, W-O
PM797X220
PM809X220
PM810X220
PM811X220
PM812X220
PM818X220
PM824X220
PM855X220
PM856X220
PM857X220
PM860X220
PM927X220
PM220WN
13.5
10.8
16.7
19.3
25.0
12.0
12.4
13.7
23.0
21.5
17.2
14.0
5.5
style
T
T
T
T
T
T
description
tooth, tiger
tooth, std.
tooth, abr. paneled
tooth, abr.
tooth, flare, 4.5""
tooth, twin tiger
adpt., B-O, rev., crnr., Deere #112163
adpt., B-O, ctr., .81" throat
adpt., B-O, crnr. (544E, 624E)
adpt., B-O, LH, crnr., Cat #3G4258
adpt., B-O, RH, crnr., Cat #3G4259
adpt., B-O, 1.43" thr, 22deg, Clark #251 147
adpt., B-O, 1.56" thr, 33deg, Deere T35385
adpt., B-O, 1.31" throat, 22deg (Case W36)
adpt., B-O, 1.31" throat, Deere T29886
adpt., B-O, step
adpt., B-O, 1.31", Case #L58824
adpt., W-O, flush, 1.25" lip, 2"
adpt., nose, W-O
part no.
PMT225
PMX225
PMX225AP
PMX225ABR
PMX225F
PMX225WT
PM0C1X225
PM102X225
PM106X225
PM111X225
PM155X225
PM163X225
PM164X225
PM165X225
PM191X225
PM257X225
PM258X225
PM259X225
PM310X225
PM313X225
PM385X225
PM473X225
PM544X225
PM785X225
PM572X225
PM611X225
PM703X225
PM747X225
PM796X225
PM797X225
PM810X225
PM811X225
PM818X225
PM824X225
PM855X225
PM857X225
PM860X225
PM900X225
PM902X225
PM903X225
PM904X225
PM225WN
a
b
c
d
lbs.
5.0
6.2
8.4
11.0
6.0
8.5
21.2
15.8
16.4
22.6
21.7
15.8
12.3
14.2
20.5
18.2
24.8
24.8
24.1
23.6
17.1
14.4
16.2
19.7
15.0
15.0
18.7
16.2
18.7
13.5
16.7
19.3
12.0
12.4
13.2
21.5
17.2
12.8
24.1
30.0
30.0
5.7
style
T
T
T
T
T
T
3
3
description
Fanggs
standard
tiger
twin tiger
flare
abrasion panel
adapter
adapter
abrasion
adapter
adapter
adapter
adapter
adapter
adapter
nose template kit for 290, 330
nose rebuild kit for 290 series
adpt., stake type, ESCO C-19 lip
adpt., W-O, 1-1/2 leg, RH, 1.75"
adpt., W-O, 1-1/2 leg, LH, 1.75"
adpt., stake type, Hensley C-19
adpt., B-O LH crnr. (955L)
adpt., B-O RH crnr. (955L)
adpt., W-O, bttm. Leg, 1.25"" to 1.5" lip
adpt., B-O, 2 leg, 1.93" thr. 23deg, (85Z11)
adpt., B-O, LH (85Zll), (req. 486INS)
adpt., B-O, RH (85Zll), (req. 486INS)
adpt., B-O, LH (80Zlll)
adpt., B-O, RH (80Zlll)
adpt., B-O, 2 leg, 1.03" thr. (80Z111)
adpt., W-O, 1-1/2 leg, 1.375" lip
adpt., stake type (Akerman H9, H11)
adpt., B-O, ctr., 1.375" thr.
adpt., B-O, ctr., 1.31" thr. (Case 821)
adpt., B-O rev. crnr. VME L-14
nose weld-on
part no.
TF290
TX290
TT290
TX290WT
TX290F
TX290AP
T127X290
T158X290
PMX290ABR
PM125X290
PM150X290
PM190X290
PM191X290
PM673X290
PM822X290
PMA-TEM
PMA290NR
PMX290SYL
PM119X290
PM124X290
PM130X290
PM131X290
PM136X290
PM156X290
PM308X290
PM309X290
PM383X290
PM430X290
PM480X290
PM486X290
PM487X290
PM488X290
PM489X290
PM490X290
PM580X290
PM589X290
PM721X290
PM722X290
PM820X290
PM821X290
PM904X290
PM905X290
PM290WN
a
b
c
8-1/4"
3-1/4"
2-7/8"
8-1/4"
3-3/16"
2-7/8"
10"
3/16"
2-7/8"
9-3/4"
4-5/8"
2-7/8"
8"
6-1/4"
2-7/8"
8-1/2"
4"
2-7/8"
1-1/4"
7-1/2"
7-1/2"
1-1/2"
2-7/8"
8-3/16"
3-3/4"
1-1/4"
10"
9"
1-1/2"
10"
9"
3-13/32" 4-25/32" 1-5/16"
2-15/16"
4-3/4"
4-1/4"
3-5/8"
1-3/8"
d
lbs.
2-11/16"
2-11/16"
2-11/16"
2-11/16"
2-11/16"
2-11/16"
30°
30°
2-11/16"
10.4
8.6
8.8
10.2
11.6
10.4
21.5
22.7
10.2
23.2
19.9
21.5
21.5
27.5
22.0
11.4
2.3
9.2
18.8
24.3
22.6
22.6
20.1
31.2
39.5
39.5
18.7
30.0
24.3
34.8
34.8
37.1
37.1
23.8
20.2
26.6
21.0
24.0
27.0
24.0
36.2
26.3
7.3
1-3/16"
1-1/8"
style
T
T
T
T
T
T
description
std. tooth
tiger tooth
twin tiger tooth
abr. panel tooth
flare tooth
adpt. 1-1/4" lip
adpt., C-19 cast lip
adpt. 1-1/2" lip
adpt. B-O L.H.
adpt., B-O R.H.
adpt. bttm. leg W-O
adpt., B-O
adpt., stake type, Akerman H7
adpt., W-O nose
part no.
a
b
c
d
lbs.
8.2
8.7
10.5
10.8
10.3
12.8
21.9
20.6
22.8
39.8
39.8
19.2
30.2
26.8
8.1
a
b
c
d
lbs.
10.5
7.5
14.5
9.8
7.5
12.5
13.3
7.2
PM295
PMT295
PM295WT
PM295AP
PM295SYL
PM295F
PM127X295
PM136X295
PM158X295
PM308X295
PM309X295
PM383X295
PM430X295
PM589X295
PM295WN
style
T
T
T
T
T
T
T
description
tooth, tiger
tooth, std.
tooth, abr.
tooth, abr. paneled
tooth, flare, 6""
tooth, heavy duty rock
tooth, twin tiger
adpt. nose, W-O
part no.
PMT300
PMX300
PMX300ABR
PMX300AP
PMX300F
PMX300R
PMX300WT
PM300WN
style
T
T
T
T
T
T
T
2
Fanggs
standard
description
part no.
TF310
TX310
a
7-1/2"
8"
b
3-1/4"
3-3/8"
c
3"
3"
d
2-1/8"
2-1/8"
tooth, std., 4" wide
tiger
PMX310-4
TT310
9-7/8"
1/4"
twin tiger
flare
abrasion paneled
adapter
adapter
key
refer also to 142X330
adpt., W-O, l-1/2 leg, 2" lip
adpt., W-O, flush, 1.25" lip
adpt., W-O, 1-1/2 leg, 1.25" lip
adpt., W-O, 1-1/2 leg, 1.25" lip
adpt., W-O, RH, 1-1/2 leg, 1.75"
adpt., stake-type, C-19 lip (reqs P136)
adpt., flush, 1.5" str. lip
adpt., RH, flush, 1.5" sp. lip
adpt., LH flush, 1.5" sp. lip
adpt., W-O, RH, 1-1/2 leg, 1.5" lip
adpt., W-O, LH, 1-1/2 leg, 1.5" lip
adpt., W-O, 1-1/2 leg, 1.5" lip
adpt., B-O, 1.46" thr. Komatsu D65, D75
adpt., B-O, LH crnr. (955L)
adpt., B-O, RH crnr. (955L)
adpt., B-O, 1.31" thr., 22deg, Case 1450
adpt., B-O, specialty item
adpt., W-O, bttm. leg, 1.25"" to 1.5" lip
adpt., B-O, step
adpt., B-O, 2 leg, 1.81" thr, Furukawa 320A
adpt., W-O, 1-1/2 leg, 1.375" lip
adpt., stake-type (req. K668)
adpt., B-O, 1-1/2 leg, 1.375" thr
adpt., B-O, step
adpt., B-O, step
adpt., B-O, step
adpt., B-O
adpt., W-O, bttm. leg, .75"" to .875"
adpt., W-O, 1.375" special lip
adpt., B-O, 2 leg, 1.81" thr. (HD 6G, 12G)
adpt., W-O, flush, 1.5" str. lip
adpt., W-O, flush, LH, sp. lip
adpt., W-O, flush, RH, sp. lip
nose weld-on
TX310WT
TX310F
TX310AP
T153X310
PMX310ABR
PMK668
PM110X310
PM119X310
PM122X310
PM124X310
PM125X310
PM127X310
PM128X310
PM130X310
PM136X310
PM138X310
PM150X310
PM151X310
PM152X310
PM154X310
PM155X310
PM156X310
PM158X310
PM159X310
PM160X310
PM168X310
PM169X310
PM170X310
PM181X310
PM185X310
PM301X310
PM308X310
PM309X310
PM317X310
PM323X310
PM383X310
PM430X310
PM494X310
PM495X310
PM550X310
PM580X310
PM668X310
PM742X310
PM756X310
PM758X310
PM759X310
PM812X310
PM822X310
PM844X310
PM845X310
PM859X310
PM900X310
PM901X310
PM902X310
PM310WN
9-5/8"
7-7/8"
8-1/4"
7"
8-3/4"
4-3/4"
6"
4"
1-9/16"
4"
3"
3"
3"
3"
2-1/8"
2-1/8"
2-1/8"
2-1/8"
30°
2-1/4"
4-3/4"
3-3/4"
3"
lbs.
10.4
8.0
8.0
11.6
12.2
8.6
10.3
21.4
14.5
2.0
24.5
18.0
17.5
23.0
21.9
20.2
20.5
21.4
18.7
22.5
19.7
19.7
19.5
22.1
22.1
30.5
21.9
15.7
15.7
33.5
37.2
37.6
29.0
24.0
24.0
37.4
37.4
25.1
33.5
17.9
29.5
23.7
35.0
31.6
21.2
21.5
23.0
24.7
36.2
33.0
26.9
22.0
17.9
26.9
31.4
19.5
19.7
19.9
7.5
style
T
T
T
T
T
T
T
T
2
description
Fanggs
standard
tiger
twin tiger
flare
abrasion panel
short rock
abrasion
adapter
adapter
adapter
adapter
adapter
adapter
lip fastener, C-19 lips (136X330, 136X310)
lip fastener, C-29 lips (236X330)
steel wedge
adpt., W-O, 1-1/2 leg, 1.625" lip
adpt., B-O specialty item (Sauerman)
adpt., W-O, bttm. leg, 1.25"" lip, 23deg
adpt., B-O, ctr. (VME L150, L180)
adpt., B-O, ctr. (Case 921)
nose weld-on
part no.
TF330
TX330
TT330
TX330WT
TX330F
TX330AP
PM X330SYL
PMX330SR
PMX330ABR
T158X330
PM190X330
PM743X330
PM744X330
PM822X330
PM937X330
PMA330NR
PMP136
PMP236
PMW330
PM136X330
PM159X330
PM160X330
PM225X330
PM236X330
PM323X330
PM383X330
PM901X330
PM921X330
PM935X330
PM936X330
PM330WN
a
9-1/4"
9-1/4"
11-5/8"
11-5/8"
9-5/8"
9-1/2"
b
3-5/8"
3-5/8"
3/16"
5-1/4"
7-1/4"
4-1/2"
c
3-13/32"
3-13/32"
3-13/32"
3-13/32"
3-5/8"
3-5/8"
d
3-3/16"
3-3/16"
3-3/16"
3-3/16"
3-1/8"
3-1/8"
lbs.
15.3
11.9
11.9
14.7
18.1
15.4
14.9
14.4
15.5
35.2
32.9
64.0
44.0
28.3
32.9
2.7
0.8
2.1
0.8
24.8
28.7
28.7
30.4
47.8
41.4
23.5
41.0
29.0
29.4
29.4
10.9
8-3/8"
9-1/4"
8"
4-1/4"
4-1/4"
1-9/16"
3-5/8"
3-5/8"
3-1/8"
3-1/8"
30°
5-1/8"
4-1/4"
b
c
d
lbs.
12.5
15.1
17.9
15.3
13.2
15.3
34.6
34.5
48.7
38.3
31.7
31.7
33.1
12.1
b
c
3-1/2"
d
2-7/8"
lbs.
18.4
15.0
18.7
18.3
20.7
14.5
b
c
d
lbs.
style
T
T
T
T
T
T
description
std. tooth
abr. panel tooth
flare tooth
tiger tooth
twin tiger tooth
adpt., 1.5" lip
adpt., W-O, flush 1.625" - 1.75" lip, 30 deg
adpt., C-29 Hensley cast lip
adpt., L.H. crnr., 1.75" lip
adpt., R.H. crnr. 1.75" lip
adpt., 1.75" lip
adpt., W-O nose
part no.
PM335
PM335AP
PM335F
PM335SYL
PMT335
PM335WT
PM158X335
PM190X335
PM236X335
PM355X335
PM935X335
PM936X335
PM937X335
PM335WN
a
style
T
T
T
T
T
description
standard
tooth, tiger
tooth, abr. paneled, short
tooth, flare
tooth, twin tiger
adpt. nose, W-O
part no.
TX350
PMT350
PMX350APS
PMX350F
PMX350WT
PM350WN
a
11"
4"
style
description
part no.
a
T
T
T
T
T
T
T
T
1
Fanggs
standard
tiger
twin tiger
abrasion paneled
flare
TF370
TX370
TT370
TX370WT
PMX370AP
PM370F
abrasion
steel keeper
fastener for Hensley C-29 lips
adpt. W-O, ctr., 2" lip
adpt., W-O, RH/LH, 1.75" sp. lip
adpt., W-O, ctr., 1.75" str. lip
adpt., W-O, LH, 2" flush sp. lip
adpt., W-O, RH, 2" flush, sp. lip
adpt., W-O, ctr., 2" flush, str. lip
nose weld-on
PM X370SYL
PM370ABR
TK370S
T940X370
PMP236
PM129X370
PM158X370
PM236X370
PM827X370
T940X370
PM936X370
PM937X370
PM947X370
PM948X370
PM949X370
PMA370NR
PM370WN
10-1/4"
10-1/4"
12"
12"
10-7/8"
10-1/4"
4"
4-1/8"
point
6"
5"
8"
3-5/8"
3-5/8"
3-5/8"
3-5/8"
3-5/8"
3-5/8"
3-3/8"
3-3/8"
3-3/8"
3-3/8"
3-3/8"
3-3/8"
11-3/4"
4-5/8"
3-5/8"
3-3/8"
5-1/4"
10-3/4"
2-1/16"
30°
5-3/4"
4-5/8"
c
d
22.9
17.8
18.2
21.0
21.4
22.9
19.4
25.6
1.0
36.4
2.1
33.7
35.3
52.0
35.2
36.4
41.9
35.6
40.5
40.5
38.7
4.8
14.7
style
T
T
T
T
T
description
tooth, std.
tooth, flare
tooth, tiger
tooth, twin tiger
adpt., stake type, Hensley C29
adpt., W-O, bttm. leg
adpt., W-O, 1-1/2 leg, 1.75" lip
adpt., W-O, flush, 2" lip
adpt., W-O nose
part no.
PM385
PM385F
PM385SYL
PMT385
PM385WT
PM236X385
PM355X385
PM827X385
PM937X385
PM940X385
PM949X385
PM385WN
a
b
lbs.
21.4
30.9
24.9
22.1
24.1
57.0
44.5
44.3
44.7
43.4
51.5
19.7
style
T
T
T
T
T
T
T
T
T
T
T
2
description
Fanggs
part no.
TF400
a
9-1/4"
b
4-1/2"
c
4"
4"
4"
4"
4"
4"
4"
4"
4"
4"
4"
d
2-7/8"
2-7/8"
2-7/8"
2-7/8"
2-7/8"
2-7/8"
3"
3"
3"
30
3"
standard
tiger
twin tiger
flare
abrasion paneled
abrasion
abrasion heavy
short
long sharp
penetrator narrow
slag pin
slag pin
slag pin
adapter
adapter
wedge key
adpt., W-O, 1-1/2 leg, 1.5" lip
adpt., W-O, 2 leg, ctr., 2" lip
adpt., W-O, notched crnr., LH
adpt., W-O, notched crnr., RH
nose weld-on
TX400
TT400
TX400WT
TX400F
TX400AP
PMX400ABR
PMX400ABRB
PMX400H
PMX400LS
PMX400SD
PMP400SA
PMP400SB-S
PMP400SB-OS
T802X400
PM800X400
PMK129C
PM129X400
PM236X400
PM604X400
PM827X400
PM830X400
PM831X400
PM832X400
PM938X400
PM940X400
PM945X400
PMA410NR
PM400WN
10"
12-1/4"
12-1/4"
10-1/2"
10-5/8"
11"
11"
8-7/8"
12-5/8"
10-3/4"
4"
3/8"
6"
8"
5-1/2"
4-3/4"
4-3/4"
4-3/4"
4-1/4"
2-1/4"
9"
2-1/16"
6"
5-1/4"
part no.
TF410
TX410
TX410WT
TT410
PMX410ABR
PMX410AP
PMX410F
PMX410LS
PMX410SYL
TK410S
T940X410
PM236X410
PMA464X410
PMA465X410
PMA466X410
PM827X410
PM890X410
PM937X410
PM410WN
a
11-1/4"
11-3/8"
13-5/8"
13-5/8"
13"
12"
11-3/8"
b
4-3/8"
4-9/16"
6-5/8"
point
5-1/8"
5-1/2"
9"
c
4-1/16"
4-1/16"
4-1/16"
4-1/16"
4-1/16"
4-1/16"
4-1/16"
d
3-3/4"
3-3/4"
3-3/4"
3-3/4"
3-3/4"
3-3/4"
3-3/4"
5-1/4"
11"
2-1/16"
30°
30°
lbs.
10.4
16.2
18.6
24.1
21.6
21.8
25.8
28.9
21.7
23.0
17.9
0.3
0.3
0.3
48.0
40.0
2.5
36.5
54.0
36.8
48.0
45.3
41.0
41.0
44.9
46.0
52.0
5.3
16.7
style
T
T
T
T
T
T
T
T
T
1
description
Fanggs
standard
twin tiger
tiger
abrasion
abrasion paneled
flare
tooth, long, sharp
steel keeper
adpt., stake type Hensley C-29
adpt., W-O, 2 leg, 2" str. lip
adapt., W-O bttm. leg
adpt., W-O 1-1/2 leg 1.75" lip
nose weld-on
lbs.
28.5
21.7
27.6
22.6
36.3
28.3
32.9
25.2
26.5
1.2
43.4
57.0
60.7
62.4
62.4
44.2
45.8
44.5
19.7
style
T
T
T
T
T
T
description
tiger
standard
flare
abrasion
abrasion paneled
twin tiger
nose weld-on
part no.
PMT450
PMX450
PMX450F
PMX450ABR
PMX450AP
PMX450WT
PM450WN
a
15"
12-1/2"
12-1/2"
14-3/8"
13-1/4"
15"
b
point
4-7/8"
10"
5-5/8"
6"
7-1/4"
c
4-9/16"
4-9/16"
4-9/16"
4-9/16"
4-9/16"
4-9/16"
d
4-5/16"
4-5/16"
4-5/16"
4-5/16"
4-5/16"
4-5/16"
lbs.
31.3
30.2
44.8
46.5
40.8
37.5
28.0
part no.
TF475
TX475
TT475
TX475WT
TX475F
TX475AP
T303X475
PMX475ABR
PMX475AH
PMX475AHL
PMX475AHS
PMX475LP
PMX475S
PMT475L
PMX475WTL
PM988X475
PM475WN
a
11-7/8"
12-1/2"
14-1/4"
14-3/8"
11-5/8"
13-1/4"
8/14"
13"
12-5/16"
15"
12-13/16"
12-1/8"
9-13/16"
15-1/2"
15-1/2"
b
5/34"
5/34"
1/4"
7"
8-7/8"
6-1/2"
2-9/16"
5-3/4"
5-3/4"
5-3/4"
6-3/4"
6-1/4"
5-3/4"
point
7"
c
4-3/4"
4-3/4"
4-3/4"
4-3/4"
4-3/4"
4-3/4"
4-3/4"
4-3/4"
4-3/4"
4-3/4"
4-3/4"
4-3/4"
4-3/4"
4-3/4"
d
3-1/2"
3-1/2"
3-1/2"
3-1/2"
3-1/2"
3-1/2"
30°
3-1/2"
3-1/2"
3-1/2"
3-1/2"
3-1/2"
3-1/2"
3-1/2"
3-1/2"
7-1/4"
6-1/2"
lbs.
40.7
39.5
31.1
37.0
29.9
40.0
75.0
40.3
43.8
49.1
59.0
39.5
30.9
37.6
37.6
86.3
28.0
part no.
TX500
TX500AP
TX500SYL
T806X500
a
14"
14-3/4"
15-1/2"
10"
b
5-5/8"
6-3/4"
6"
3-1/16"
c
5"
5"
5"
8"
d
4-11/16"
4-11/16"
4-11/16"
30°
lbs.
48.5
54.0
50.0
104.0
part no.
TX550SYL
T806X550
a
18-1/4"
12"
b
7"
3-1/16"
c
5-7/8"
9"
d
5-5/8"
30°
lbs.
91.0
165.0
style
T
T
T
T
T
T
2
description
Fanggs
standard
tiger
twin tiger
flare
abrasion paneled
adapter
abrasion
slag heavy
slag long
slag h-bottom
long heavy
slag
tiger long
twin tiger long
adapter
nose weld-on
style
T
T
T
description
std. tooth
abrasion panel
ribbed sharp
adapter
style
T
description
ribbed sharp
adapter
Sidecutters
style
description
sidecutter, blade-type, RH, 2/2
sidecutter, blade-type, LH, 2/2
part no.
PMSCB220-SO
PMSCB330-SO
PMSCB410-SO
PMB311LH
PMB312RH
PMB330RH
PMB331LH
PMB102RH
PMB103LH
PM330X310
PM331X310
PM102X400
PM103X400
a
b
c
d
lbs.
21.9
33.0
41.8
29.8
29.9
45.2
45.2
59.2
59.5
28.0
28.0
61.0
61.0
part no.
PM099HX
PM50CHX
PM50LH
PM50RH
PM100CHX
PM1020HX
PM500CHX
PM100LH
PM100RH
PM500LH
PM500RH
PM1000HX
PM1000LH
PM1000RH
PM3000HX
PM4330CHX
PM4330WN
PM1025HX
PM2030HX
PM3040HX
PM4050HX
PM5060HX
PMCG6
PMCG9
PMCG12
PM1030HHX
PM2060HHX
PM60100HX
PM3000LH
PM3000RH
PM3000H
PM3000HLH
PM3000HRH
PM3000RC
PM11V16L
PM11V16R
PM13V16L
PM13V16R
PM110HX
a
b
c
d
lbs.
3.5
21.0
21.0
71.5
11.7
2.6
21.0
3.1
3.1
21.2
21.0
2.5
1.8
1.8
6.9
13.8
22.5
4.4
10.0
18.4
34.0
61.0
2.1
6.8
16.6
8.6
16.0
32.8
5.9
5.9
6.7
5.9
5.9
8.0
23.0
23.0
26.6
26.6
8.2
Hensley Attachments
style
description
one-piece tooth, B-O
tooth, ctr., long, early style
tooth, LH. long, early style
tooth, RH. long, early style
tooth, ctr.
tooth, ctr.
tooth, ctr., short
tooth, LH
tooth, RH
tooth, LH, short
tooth, RH, short
tooth, ctr.
tooth, LH
tooth, RH
tooth, ctr., continuous edge
continuous edge ctr. tooth
continuous edge W-O nose
closed lifting eye, large I.D., 10-20,000
crnr. gusset
crnr. gusset
crnr. gusset
tooth, LH
tooth, RH
tooth, ctr., heavy
tooth, LH, heavy
tooth, RH, heavy
tooth, ctr. (round & T bucket)
blade (156 nose)
blade (156 nose)
blade (162 nose)
blade (162 nose)
lb.
lb.
lb.
lb.
lb.
excav.
excav.
excav.
excav.
excav.
Hensley Attachments
style
description
adpt., ctr. (parabolic 400 nose)
adpt., LH (parabolic 400 nose)
adpt., RH (parabolic 400 nose)
adpt., ctr.
adpt., LH
adpt., RH
adpt., ctr., continuous edge
adpt., LH, continuous edge
adpt., RH, continuous edge
adpt., ctr. (round & T bucket)
adpt., RH/LH (round & T bucket), less W-O nose
nose, W-O, ctr.
nose, W-O, LH
nose, W-O, RH
nose, W-O
nose, W-O
nose, W-O
nose, W-O, LH (round & T bucket), ref. 3010RRL
nose, W-O, ctr. (round & T bucket)
nose, W-O, RH (round & T bucket), ref. 3010RRL
nose, W-O, ctr.
nose, W-O, ctr., continuous edge
nose, W-O, LH, continuous edge
nose, W-O, RH, continuous edge
washer (old #3G9549W)
part no.
PM110LH
PM110RH
PM510HX
PM510LH
PM510RH
PM1010HX
PM1010LH
PM1010RH
PM3010HX
PM3010LH
PM3010RH
PM3010RC
PM3010RRL
PM1010WN
PM1010WNL
PM1010WNR
PM9J4354WN
PM156WN
PM220WN
PM3010LWN
PM3010WNRC
PM3010RWN
PM1030WN
PM3010WN
PM3010WNL
PM3010WNR
PM6Y9459W
a
b
part no.
TT156
TX156L
PMS156
PMS156HD
PMT156HD
PMX156F
PMX156H
PMX156LP
PM156
PMB922B
PM922X156
PM156WN
a
6-1/4"
b
1/8"
6"
6-1/16"
6-1/4"
5"
5-1/2"
1-1/8"
1-1/8"
point
4-3/8"
2"
description
part no.
tooth, tiger
TT160
tooth, std.
TX160
tooth, star
PMS160
tooth, heavy duty
PMX160HD
adpt., B-O, 1-1/2 leg, 1.18 throat, 33 degrees (JD444)
PM552X160
adpt., W-O, bottom leg, 1-1 1/4 edge, 30 degrees PM850X160
ripper box
PMB926A
ripper sh. (B922B)
PM922X160
ripper sh. (B926A)
PM926X160
a
c
d
lbs.
6.1
5.9
70.5
40.0
40.0
7.0
4.5
4.5
19.1
14.7
14.7
36.0
17.8
3.2
2.2
2.2
10.7
1.8
5.5
7.5
10.5
7.5
2.6
8.9
6.9
6.9
0.1
c
1-5/8"
d
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
lbs.
1.8
1.7
2.4
2.7
2.1
2.8
2.6
3.6
0.1
14.7
23.0
1.8
Hensley Ripper Teeth - Specifications
156 Series
style
T
T
T
T
T
T
T
T
description
tooth, tiger
tooth, long
tooth star
tooth, heavy duty star
tooth , tiger, heavy duty
tooth, flare, 4.375
tooth, heavy
tooth, extra long
roll pin
ripper box
ripper sh. (B922B)
nose, W-O
160 Series
style
T
T
T
T
b
c
d
lbs.
4.2
3.5
4.4
4.5
11.4
7.5
58.7
22.6
50.0
162 Series
style
description
box ripper sh. (B922B)
box ripper sh. (B926A)
part no.
PM922X162
PM926X162
a
b
c
d
lbs.
23.6
50.0
501 Series
style
T
T
description
part no.
TT501
PM501HX
PMB944
PMB977
PM944-501
PM977-501
PM501WN
a
b
c
d
lbs.
12.5
10.7
80.0
164.0
72.5
114.0
14.0
description
tiger tooth
tiger tooth, long
twin tiger tooth
twin tiger tooth, long
std. tooth
nose, W-O
part no.
TT702
TT702L
PMX702WT
PMX702WTL
PM702HX
PM977-702
PM977-702L
PM702WN
a
b
c
d
lbs.
25.2
26.9
31.0
30.0
25.5
141.0
210.4
37.8
teeth, tiger
teeth, std.
ripper box
ripper box
ripper sh. (B944)
ripper sh. (B977)
nose, W-O
702 Series
style
T
T
T
T
T
Replacements for Hensley Products
Retainers
TK290
290 Series
TK330
330 Series
TP400HD
350, 400 Series
TP475
475 Series
Hensley
17
Replacements for Hensley Products
Retainers
TP156 - 156 Series (Except Fanggs)
TF13P - 156 Series (Fanggs or Other)
TP160 - 160; 220; 310 Series (Except 310 Fanggs)
TP160L - 310 Series Fanggs
Hensley
18
John Deere Replacements for H & L Products
Various information can be determined from the part number system. Refer to the
following charts for basic part numbering information.
Part Number Explanation for Teeth
Part Number Explanation H & L Products
Prefix
TF
TF
T
T
T
T
T
T
T
TT
Suffix
D
L
F
R
SP
L
ST
WT
A, C
CR
Examples:
Part Number T250F
Part Number T230ST
Explanation
Fangg Digging
Fangg Loading
Standard
Flare
Rock
Standard
Long
Star
Twin Tiger
Tiger
Crimp-On
Crimp-On Rock
Note:
1 or 2 digits in the part number
indicates fabricated teeth.
3 digits in the part number
indicates steel or ADI teeth.
TF_P indicates Fanggs Flex Pin.
T_P indicates STD Flex Pin.
25 Series Flare Tooth
23 Series Star Tooth
Part Number Explanation for Adapters
Part Number Explanation for Replacement H & L Adapters
Relate the correlating digit and part no. to the explanation below:
Digit:
1 2 3 4 5 6 7 8
Part No.
T 4 2 7 X 2 4 0 T427X240 = Weld-On Center Adapter for 24
Series
Digit
Explanation
1
(T) John Deere Part
2
Adapter Style Code
1 - Bolt-On Center
2 - Bolt-On End
3 - Weld-On End
4 - Weld-On Center
5 - Weld-On Left-Hand
6 - Weld-On Right-Hand
7 - Weld-On Bottom Leg
8 - Weld-On Flush Mount
9 - Scarifier/Ripper
3-4
Leg Spread (mm)
5
(X) Adapter Part
6-7-8
Tooth Series
(TF_D) (Non-Centerline)
(TF_L) (Non-Centerline)
Flare Teeth
(T_F) (Centerline)
•
•
•
•
For general-purpose-toheavy digging.
Provides a clean start and
close crowd.
•
For general purpose to heavy
digging/loading conditions.
Flat bottom for better bucket
control.
For digging in loose and
mud-like conditions.
Standard Teeth
(T_SP) (Non-Centerline)
Standard Teeth Fabricated
(T_) (Non-Centerline)
Long Rock Teeth
(T_R) (Non-Centerline)
•
•
•
•
heavy-duty digging and
loading
Excellent penetration and
wear.
For light-duty, general
digging and applications.
•
For heavy-duty and extra
heavy-duty applications.
Additional wearlife.
Star Teeth
(T_ST) (Non-Centerline)
Tiger Teeth
(TT_) (Non-Centerline)
Twin Tiger Teeth
(T_WT) (Non-Centerline)
•
•
•
Excellent penetration in
rock, hardpan, and frost.
tough material.
•
Use as a corner tooth with
tiger teeth in the center.
John Deere Replacements for H & L Products
Various information can be determined from the part number system. Refer to the
following charts for basic part numbering information.
Part Number Explanation for Teeth
Part Number Explanation H & L Products
Prefix
TF
TF
T
T
T
T
T
T
T
TT
Suffix
D
L
F
R
SP
L
ST
WT
A, C
CR
Examples:
Part Number T250F
Part Number T230ST
Explanation
Fangg Digging
Fangg Loading
Standard
Flare
Rock
Standard
Long
Star
Twin Tiger
Tiger
Crimp-On
Crimp-On Rock
Note:
1 or 2 digits in the part number
indicates fabricated teeth.
3 digits in the part number
indicates steel or ADI teeth.
TF_P indicates Fanggs Flex Pin.
T_P indicates STD Flex Pin.
25 Series Flare Tooth
23 Series Star Tooth
Part Number Explanation for Adapters
Part Number Explanation for Replacement H & L Adapters
Relate the correlating digit and part no. to the explanation below:
Digit:
1 2 3 4 5 6 7 8
Part No.
T 4 2 7 X 2 4 0 T427X240 = Weld-On Center Adapter for 24
Series
Digit
Explanation
1
(T) John Deere Part
2
Adapter Style Code
1 - Bolt-On Center
2 - Bolt-On End
3 - Weld-On End
4 - Weld-On Center
5 - Weld-On Left-Hand
6 - Weld-On Right-Hand
7 - Weld-On Bottom Leg
8 - Weld-On Flush Mount
9 - Scarifier/Ripper
3-4
Leg Spread (mm)
5
(X) Adapter Part
6-7-8
Tooth Series
(TF_D) (Non-Centerline)
(TF_L) (Non-Centerline)
Flare Teeth
(T_F) (Centerline)
•
•
•
•
For general-purpose-toheavy digging.
Provides a clean start and
close crowd.
•
For general purpose to heavy
digging/loading conditions.
Flat bottom for better bucket
control.
For digging in loose and
mud-like conditions.
Standard Teeth
(T_SP) (Non-Centerline)
Standard Teeth Fabricated
(T_) (Non-Centerline)
Long Rock Teeth
(T_R) (Non-Centerline)
•
•
•
•
heavy-duty digging and
loading
Excellent penetration and
wear.
For light-duty, general
digging and applications.
•
For heavy-duty and extra
heavy-duty applications.
Additional wearlife.
Star Teeth
(T_ST) (Non-Centerline)
Tiger Teeth
(TT_) (Non-Centerline)
Twin Tiger Teeth
(T_WT) (Non-Centerline)
•
•
•
Excellent penetration in
rock, hardpan, and frost.
tough material.
•
Use as a corner tooth with
tiger teeth in the center.
H & L Products
New Product
Polyurethane "Swamper"
2 Series
style
f
d
-
description
standard
long rock
adapter
adpt., W-O, flush
part no.
T2A
T2AR
T716X2A
PML2520W2AHX
rcv. disc. non stock
9
9
JD: 172TX
9
used on
9
9
used on
3 Series
style
d
h
a
a
-
description
part no.
long rock
T3CR
flare
T3CF
standard
PMT3C
standard
PM3CHXL
adapter
T716X3C
adpt., W-O, flush, cast-in placPM1001-3CHX
adpt., W-O, flush
PM1002-3CHX
9
JD: 27ZTS, 35ZTS
23 Series
style
g
e
a
f
b
c
h
i
d
h
j
i
-
description
part no.
fanggs d
TF23D
fanggs l
TF23L
pin
TF23P
standard
T230SP
standard
T23
tiger
TT230L
twin tiger
T230WTL
flare
T230F
star
T230ST
long rock
T23R
flare
PM23HXF
Swamper
T230SWPR
tooth, star (heavy duty)
PMS230
pin
T23P
pin
PM23PB
pin
PM23PC
pin
PM23PD
adapter
T417X230
adapter
T728X230
adapter
U43792
PM230010
adapter
adapter
PM2300FL
adpt., W-O, long leg on bttm.PMD834-23HX
adpt. nose, W-O
PM23WN
adpt., W-O, .875" lip
PM2740AW-23
PM2740MW-23
12" lip blade, w/(3)
PM12M480-12A
PM18M480-12A
PM24M480-12A
9
9
9
9
9
9
9
9
9
9
used on
9
9
9
9
9
JD: Buckets with 23 Series-type adapter, 210C, 210CL,
300D, 500C, 510, 500A, 500B, 310, 310A, 310B, 310C,
310D, 310E, 310SE, 401D, 410, 410B, 410C, 410D,
410E, 315C, 315D, 315E, 510B, 510C, 510D, 610B,
610C, 710B, 710C, 710D, 315SE, 50ZTS, Skid-Steer:
JD14, JD24, JD24-A, Case: 480F, 580K, 580L, 590,
590L, 680L, 780D,
Competitive: Buckets with 23 Series-type adapters,
Ford: 555D, 575D, 655D, 710D, 755B
H & L - Applications
24 Series
style
a
a
I
b
c
d
h
-
description
standard
standard
rock
star
tiger
twin tiger
long
sharp
tooth, flare, 4" tip
pin
pin
adapter
adpt., W-O, misc.
adpt., nose, W-O
part no.
T240
PM24HD
PM24R
PMS240
TT240
T240WT
used on
Competitive: Backhoes with 24 Series-type adapters.
9
9
9
9
9
9
PM24SPHX
PM24HXSS
PM24HXF
T24P
9
PM24PBHX
T427X240
PM809-24HX
PM2740-24HX
PM24WN
9
N.S.
N.S.
25 Series
style
description
part no.
TF252
g fanggs d
- pin
TF25P
a standard
T252
h flare
T252F
I star
T252ST
PM250TW
c twin tiger
d long
PM251HX
- pin
T25P
PM25/26PD
- oversize pin
- adapter
PM2500150
- adapter
T440X252
adpt., W-O, long leg on bttm. PM855-252HX
PM2740AW-252
PM2740FW-252
adpt., W-O, long leg on bttm. PM3000W-252HX
adpt., B-O (case 850/1150B) PML4079-252HX
used on
9
JD: 690, 690A, 690B, 690C, 690D, 690E, 200LC, 120LC
Competitive: Excavators with 25-Series
9
type adapters
9
9
9
9
9
9
N.S.
N.S.
N.S.
26 Series
style
a
a
b
description
standard
standard
tiger
pin
oversize pin
part no.
T260
PM26HX
PMT26
T25P
PM25/26PD
used on
9
670, 670A, 670B, 672A, 672B, 170, 770A, 770B, 772A
772B, 772D BH, 772BH
9
27 Series
style
a
a
a
h
d
b
c
-
description
part no.
standard
T271
PM27
standard
standard
PM271HX
flare 7"
PM27HXF
long
PM27HXL
tiger
PMT27
twin tiger
PM27WT
pin
T27P
adpt., W-O, long leg on bttm.PM3000W-27HX
adapter
PM2700150
used on
9
Competitive: Excavators with 27 Series-type
adapters, Komatsu: PC150LC-5, PC200LC-5
9
N.S.
9
N.S.
H & L Ripper Teeth - Applications
18, 20, 21, 22, 23 Series
style
description
tooth, ripper, standard
tooth, ripper, sharp
tooth, ripper, tiger
flex pin
tooth, standard, rock
tooth, standard,
tooth, tiger
flex pin
adpt., nose, W-O ripper
part no.
PM18HX
PM18SSHX
PMT18
PM18P
PM20HXR
PM20HXS
PMT20
PM21HX
PM22HX
PM21/22
PM23RWN
N.S.
N.S.
N.S.
used on
H&L - Specifications
Type 1
Type 2
T
Type 3
2 Series
style
T
T
2
T
T
T
description
part no.
standard
T2A
long rock
T2AR
adapter
T716X2A
standard
PMT3C
flare
T3CF
standard
PM3CHXL
adpt., W-O, flush
PML2520W2AHX
adpt., W-O, flush, cast-in place PM1001-3CHX
adpt., W-O, flush
PM1002-3CHX
a
4-1/4"
4-5/16"
4-3/4"
4-15/16"
b
1-3/4"
1-3/4"
1"
2-1/4"
c
d
1-1/16" 1-1/16"
1-1/16" 1-5/16"
4"
30°
1-9/16" 1-11/16"
lbs.
1.1
1.2
1.5
1.4
2.4
3.9
3.7
18 Series
style
T
T
T
description
rip standard
rip sharp
rip tiger
part no.
PM18TL
a
10-1/2"
b
point
c
2-1/2"
d
3-1/4"
lbs.
3.1
PM18HX
PM18SSHX
PMT18
10-5/9"
2-3/8"
2-1/2"
3-1/4"
14.7
9"
2-5/8"
2-1/2"
3-1/4"
10-1/2"
point
2-1/2"
3-1/4"
14
23 Series
style
description
T
fanggs d
T
T
T
T
T
T
T
T
T
T
T
T
-
-
fanggs l
standard
standard
standard
tiger
twin tiger
tiger h-d
flare
flare
star
long rock
flare
adapter
adapter
adpt., W-O, long leg on bttm.
adpt. nose, W-O
12" lip blade, w/(3)
18" lip blade, w/4 noses
24" lip blade, w/5 noses
adapter
adapter
adapter
part no.
TF23D
TF23L
T230
T230SP
T23
TT230
T230WT
TT230HD
T230F
PM23HXF
T230ST
T23R
PM23HXF
PM230010
PM2300FL
PMD834-23HX
PM23WN
PM2740AW-23HX
PM2740MW-23HX
PM12M480-12AHX
PM18M480-12AHX
PM24M480-12AHX
T417X230
T728X230
U43792
a
6"
b
1-3/4"
c
1-1/2"
d
1-5/8"
lbs.
3.6
5-7/8"
1-3/4"
1-1/2"
1-5/8"
3.4
5-7/8"
5-7/8"
5-1/8"
6-3/4"
6-5/8"
6-3/16"
5-3/8"
2"
2"
2-1/4"
3/16"
3"
3/8"
4-3/4"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
2.8
2.9
2
3.2
3.7
3.2
3.7
6-3/8"
5-7/16"
5-1/4"
3-3/8"
2-7/8"
2"
2-1/4"
4-3/8"
1-1/16"
3/4"
1-1/2"
1-1/2"
1-1/2"
2"
1-5/8"
1-5/8"
1-5/8"
23°
23°
3-5/8"
11/16"
3/4"
13/16"
1-3/4"
4-1/16"
1-1/2"
27°
25°
23°
2.6
2.4
3.2
4
3.8
3.1
1.7
3.4
4.3
31
43.7
59
3.7
3.1
3.5
3"
24 Series
style
T
T
T
T
T
T
T
T
2
T
description
standard
standard
standard
tiger
twin tiger
long
sharp
star
adapter
star
pin
tooth, flare, 4" tip
adpt., W-O, misc.
adpt. Nose, W-O
part no.
PM24R
TT240
T240WT
PM24SPHX
a
6-3/4"
6-3/8"
6-1/2"
7-1/2"
7-1/2"
7-1/2"
b
2-1/4"
2-3/8"
2-3/8"
2-1/4"
2-1/8"
2-1/4"
c
1-9/16"
1-9/16"
1-9/16"
1-9/16"
1-9/16"
1-3/5"
d
2-1/8"
2-1/8"
2-1/8"
2-1/18"
2-1/8"
2-1/8"
PM24HXSS
PMS240
6-4/5"
2-1/4"
1-3/5"
2-1/8"
7-5/8"
point
1-3/5"
2-1/8"
T427X240
PMS240
PM24PBHX
PM 24HXF
PM 809-24HX
PM 2740-24HX
PM 24WN
3-3/4"
1-1/8"
2"
23°
description
fanggs d
standard
standard
twin tiger
flare
part no.
TF252
T252
PM251HX
a
7-1/2"
6-7/8"
b
2-1/2"
2-7/8"
c
2-1/16"
2-1/16"
d
2-1/8"
2-1/8"
lbs.
8.8
6.7
PM250TW
T252F
7-9/16"
6-3/4"
3-9/16"
5-3/4"
2-1/16"
2-1/16"
2-1/8"
2-1/8"
6.8
5.5
star
long
adapter
adapter
adpt., B-O, (case 850/1150B)
T252ST
8-1/4"
1-1/8"
2-1/16"
2-1/8"
6.1
PM251HX
PM2500150
7-1/3"
3"
3"
2-7/8"
1-3/4"
1-9/16"
2"
2"
2"
2-1/8"
23°
23°
5.2
8
7.3
14
7.5
7.5
9.2
12
a
8-1/3"
9-4/5"
b
2-7/8"
point
c
2"
2"
2"
2"
2"
d
2-4/5"
2-4/5"
2-4/5"
2-4/5"
2-4/5"
lbs.
8.5
8.7
a
7"
b
2-1/8"
c
2-7/8"
d
2-1/8"
lbs.
7.9
T240
PM24HD
lbs.
4.5
3.6
3.3
4
5.1
4.3
3.5
4.2
4.8
4.5
8.8
7.4
4
25 Series
style
T
T
T
T
T
T
T
2
3
T440X252
PM 855-252HX
PM 2740AW-252HX
PM 2740FW-252HX
PM 3000W-252HX
PM L4079-252HX
26 Series
style
T
T
T
T
T
standard
tiger
standard
standard
tiger
description
part no.
PM26HX
PMT26
T260
PM26HX
PMT26
oversize pin
pin
PM25126PD
T25P
27 Series
style
description
standard
T
part no.
T271
T
T
T
T
standard
standard
flare
long
PM27
PM271HX
PM27HXF
PM27HXL
7-1/2"
7.63
7"
9"
3-5/8"
3.69
7"
3-3/4"
2-7/8"
2.88
2-7/8"
2-7/8"
2-1/8"
2.13
2-1/8"
2-1/8"
8
8
8
9.6
T
T
2
tiger
twin tiger
adapter
PMT27
PM27WT
PM2700150
PM 3000W-27HX
9-1/2"
9"
7-7/8"
Point
4"
1-11/16"
2-7/8"
2-7/8"
3"
2-1/8"
2-1/8"
23°
9.5
10.3
20
13.1
part no.
PM18HX
PM18SSHX
PMT18
a
b
c
d
lbs.
part no.
PM20HXR
PM20HXS
PMT20
a
b
c
d
lbs.
part no.
PM21HX
a
b
c
d
lbs.
part no.
PM22HX
a
b
c
d
lbs.
part no.
PM 23RWN
a
b
c
d
lbs.
H & L Ripper Teeth - Specifications
18 Series
style
description
tooth, ripper, sharp
tooth, ripper, tiger
20 Series
style
description
tooth, standard, rock
tooth, standard,
tooth, tiger
21 Series
style
description
22 Series
style
description
23 Series
style
description
adpt., nose, W-O ripper
Replacements for H & L Hardware
T23P
23 Series
T24P
24 Series
TF23P
23 Series Fanggs
T25P
25 Series
TF25P
25 Series Fanggs
T27P
27 Series
H&L
14
Ripper and Scarifier Teeth
John Deere offers a selection of both centerline and penetration-style ripper teeth.
Remember these basic concepts:
1. Longer teeth offer more wearable material.
2. Shorter tips provide more strength.
Generally, use a long centerline tooth because it provides good penetration and more wearable
material. If better initial penetration is needed, use the penetration-style tooth.
Ripper/Scarifier and Miscellaneous
1
Rippers/Scarifiers
John Deere Scarifier Motor Graders
Series
Tooth Part No.
Standard
T1L
Crimp-On
Shank
T114792
Series
Tooth Part No.
Standard
U15517
Pin
34M7070
Shank
T66192
Pin
U15522
Shank
T75520
Series
Tooth Part No.
Standard
T2D5572
Shank
T114792
-ALength
6″
-B-CWidth
Point
1-9/16″
3/16″
Fabricated
1.8 lb.
JD: 570, 570A, 570B, 670B, 672B, 760, 760A, 770A,
770B, 772A, 772B
-ALength
5-7/8″
-B-CWidth
Point
2-1/8″
3/8″
Cast
3.1 lb.
(34M7070) JD: 450G, 550G, 670, 670A, 670B, 672A,
672B, 770, 770A, 770B, 772A, 772B
(U15522) JD: 350, 350B, 350C, 450, 450B, 450C,
455D, 455E, 555, 555A, 555B
-A-B-CLength
Width
Point
7-3/8″
1-7/8″
3/16″
JD: 570, 570A, 570B, 670A, 670B, 672A, 672B, 770A,
770B, 772A, 772B
3
Rippers/Scarifiers
John Deere Scarifier Motor Graders (Continued)
Series
Tooth Part No.
Standard
T260
Pin
T25P
Shank
T44319
-ALength
7-1/4″
-BWidth
3″
-CPoint
1/4″
Fabricated
9.0 lb.
JD: 670, 670A, 670B, 672A, 672B, 770, 770A, 770B,
772A, 772B
4
Rippers/Scarifiers
Ripper Teeth
Reference 1
Reference 2
Series
Tooth Part No.
25 Series
EX25R12
Ref.
-ALength
12″
-BWidth
2″
-CPoint
1/4″
Cast
Pin
Bushing
EX25RPG
EX25RBG
Intermediate
Centerline
Top
Bottom
Top
Bottom
Penetration
Pin
Penetration
Pin
Pin
Retainer
Pin
T9W2668
1
11-1/8″
2″
3/8″
2-1/4″
3-3/8″
T149204 (Shank) JD: 670B, 672B, 770B, 772B
PM9J6586 (Shank) Cat: 4, 5, 6, 7, 12, 14, 16, 130,
140, 931, 941, 951, 955, 963, 973, 977, 983, D3, D4,
D8, D8L, D8N, D9, D9L, D9N, D10, D10N, D10R,
D11N, D11R
13-1/8″
3″
7/16″
3-1/4″
4-7/8″
Cat: D8, D8K, D8L, D8N, D8R, D9, D9N, D92, D94
14-1/2″
2-1/4″
7/16″
2-3/4″
4-7/16″
Cat: 4, 5, 6, 7, 12, 14, 16, 130, 140, 931, 941, 951,
955, 963, 973, 977, 983, D3, D8, D8L, D8N, D9, D9L,
D9N, D10, D10N, D10R, D11N, D11R
PM4T5452
1
Cat: D8, D8L, D9
1
Cat: D9L, D10, D10N, D11
1
(No Shank Available) Cat: 943, 953
PM4T5502
PM3G0500
Penetration
PM9J4259
PM8E6258
PM8E6259
4-7/8″
Cat: D7, D8, D9
1
PM4T2479
Intermediate
3-3/8″
1
T6Y0359
Intermediate
3/8″
Cat: D8, D8K, D8L, D8N, D8R, D9, D9H, D9N, D9R
1
PM4T2479
PM6J8811
T8E6358
T8E6359
3-1/2″
1
PM9W2451
Long
Pin
Washer
15-1/8″
T6Y0309
T9W2668
T8E6359
Short
Deere: Misc.
PM7J3310
PM4J2479
PM6J8811
Long/Penetration
Pin
Washer
PM9W2452
PM4T2479
PM6J8811
Intermediate
Top
Bottom
2
Pocket
Pocket
Width
Height
2-11/16″
3-3/16″
10.8 lb.
5
Rippers/Scarifiers
Series
Tooth Part No.
Penetration
Pin
Ref.
-ALength
-BWidth
-CPoint
PM4T5501
PM3G0500
Long
Pin
Retainer
Ripper Teeth (Continued)
1
(No Shank Available) Cat: D9L, D10, D10N, D11
PM1U3202
PM8E6208
PM8E6209
Short
(No Shank Available) Cat: 931, D3
PM1U3251
(No Shank Available) Cat: 943, 953
6
John Deere
Part No.
T75220
T66192
Part No.
T149204
Part No.
T44319
Part No.
T114792
Ripper Shanks
Description
Scarifier - 40˚
A
19-1/2″
B
3-5/8″
C
1″
D
7/8″
E
1″
F
1″
G
3/4″
Wt. (lb.)
15.4
Scarifier - 28˚
19-1/2″
3-5/8″
1″
7/8″
1″
1″
3/4″
17.5
Description
Shank
A
24-1/2″
B
5-1/2″
C
2-1/4″
D
4-13/64″
E
7″
Wt. (lb.)
88.4
Description
Shank, Ripper
A
28-29/32″
B
5″
C
2″
D
2-1/2″
E
9″
Wt. (lb.)
75.3
Description
Shank
A
19″
B
3″
C
1″
D
2-7/16″
E
1″
7
F
3/4″
G
3/4″
Wt. (lb.)
14.7
Miscellaneous Replacements
ADCO, Bofors, Case, Fiat-Allis, Ford, Komatsu
Reference 1
Reference 2
Series
Tooth Part No.
100 Series
T100C
Pin
TF13P
100 Series
Pin
(Center)
Ref.
Part No.
-B-CPocket
Pocket
Width
Point
Width
Height
3-3/16″
1/2″
1-5/8″
1-5/8″
Cast
3.4 lb.
Competitive: Backhoes with ADCO buckets.
1
11/16″
1-5/8″
1-5/8″
Cast
3.1 lb.
Competitive: Backhoes with ADCO buckets.
T100
TF13P
-ALength
6-3/16″
6-3/16″
(Interchangeable
right/left)
2
1/2″
Description
Pin / Description
PM3031537
Tooth
PM6254677 (Lock)
PM3031539
Tooth
PM6254682 (Lock)
PMD48212
Adapter, Weld-On
23 Series
PMD49586
Adapter, Bolt-On
23 Series
PMD49940
Adapter, Bolt-On
25 Series
Standard Tooth
PM20853P (Pin)
PM2027012130
Standard Tooth
PM0924402496
PM2057019570
Standard Tooth
PM0924402496
PM2077014151
Standard Tooth
PM1757821810
PM2087014152
Standard Tooth
PM0924403036
PM27
Fabricated Tooth
T27P
Bofors
Case
Fiat-Allis
PM20853
Komatsu
8
Caterpillar Compactor Replacement Parts
Model
834, 835
824B, 825B,
825G, 834, 835
825C, 825G
825C, 825G
815B
815, 815F
Dirt
Tamping
Foot
PM8K9171*
PM7K2939***
PM8K9171*
PM2V6628
PM2V7053
PM8K9189**
Rock
Tamping
Foot
PM7K2939***
Base
(riser)
Cleaner
Bar
PM4S7928
PM3S3228
Rock
Cleaner
Bar
PM4S7928
PM3S3228
PM3S3228
PM4V0668
PM4V3851
Cleaner
Bar
Retainer
PM3S3225
PM3S3225
PM3S3225
PM5V4311#
PM7K6908 PM5V4311#
PM7K6908 PM4S7928
* Bolt-on requires (2) 7/8" X 2-1/2" bolt, (2) 7/8" nut, and (4) PM4D6419 washer
** Bolt-on requires (2) 5/8" X 2-1/2" bolt, (2) 5/8" nut, and (4) PM5S0581 washer
*** Pin on foot
# Finger shank, uses replaceable tip T3G8250, requires T9J2258 pin, T3G9609 retainer
PM3S3225

Your Bucket Tooth - Plasterer Equipment Company

Transcription

Similar documents

MRP - Akshar Trading Co.

Poly(ethylene glycol) chemistry and protein PEGylation

- /t / " - John Deere

Internal Medicine

One Safe Source 2012-2013

CSM Cutter-Soil Mixing