manual

BELL 222
GENERAL INSTALLATION MANUAL
ENGINE SIZE:60
TAIL ATTACHMENT INSTRUCTION
SAND AREA AS INDICATED BY ARROW ON THE FRONT PORTION WITH
#180 SAND PAPER. GLUE TAIL SECTION WITH 30MIN. EPOXY AND SET
TAIL HEIGHT AS SHOWN WITH INCLUDED PLYWOOD INDICATOR.
158mm
BELL 222
ENGINE SIZE:60
NOTICE:
GENERAL INSTALLATION MANUAL
C
1
2
B
E
USE EPOXY UNLESS STATED.
SAND INSIDE FUSELAGE WITH #180 SANDING
PAPER BEFORE PARTS GLUING IN PLACE.
CUT 2.5x11 MM SLOTS IN THE HATCH.
GLUE THE PLASTIC MOUNTING BRACKETS
INSIDE.
A
D
CUT MESH ACCORDING TO THE TEMPLATE
PROVIDED. GLUE MESH WITH CA INSIDE
FUSELAGE AND TOP HATCH.
3
GLUE 3x10x10MM PLYWOOD AND 3 MM ALUM. POLES
FOR TOP HATCH AND FUSELAGE ALIGNMENT.
4
GLUE 3x16 MM PLYWOOD
IN THE FUSELAGE.
DRILL HOLES WHICH
ALIGNED TO THE ALUM.
POLES AS IN DIAGRAM.
MOUNT THE SLOTTED PLASTIC PLATES
WITH 1.4x4 MM FLAT HEAD TAPPING SCREWS.
5
6
GLUE EXHAUST
ON FUSELAGE.
FASTEN TOP HATCH WITH 3 X 12 MM
SOCKET HEAD TAPPING SCREW
7
GLUE SLOTTED BALSA AND VERTICAL FINS
IN HORIZONTAL STAB. AS SHOWN.
GLUE PLYWOOD JOINER INSIDE FUSELAGE.
8
GLUE AND ALIGN HORIZONTAL STABS.
P.1
BELL 222
ENGINE SIZE:60
GENERAL INSTALLATION MANUAL
9
10
90
90
ALIGN HORIZONTAL STABS. TO FUSELAGE AS SHOWN.
11
GLUE RED LIGHT ON TOP OF HATCH AND BOTTOM
OF FUSELAGE.
12
MOUNT TAIL HATCH WITH M3x6
ROUND HEAD TAPPING SCREW.
GLUE 1.5x10x10 MM PLYWOOD.
14
13
GLUE CLEAR LIGHT, ALUM. HOLDER
AND STEEL WIRE IN THE TAIL FIN.
15
CUT WINDSHIELD AND WINDOWS AS MARKED.
GLUE IN PLACE WITH SILICONE OR "GOOP" *.
MOUNT THE VERTICAL FIN WITH
M3x16 ROUND SOCKET HEAD SCREWS,
3x8x0.7 WASHERS AND LOCKNUTS.
16
SIDE WINDOWS ARE
GLUED INSIDE FUSELAGE
* "GOOP" IS A BRAND OF GLUE WHICH IS MANUFACTURED BY
ECLECTIC PRODUCTS, INC.
IT IS AVAILABLE IN MOST HARDWARE STORES.
INSERT TAIL BOOM INTO SPONGE RING
P.2
BELL 222
ENGINE SIZE:60
INSTALLATION OF RETRACTABLE LANDING GEAR
1
OPTIONAL PARTS
RETRACT MECHANISM
PART NO. FK 9606
2
BALL LINK
2 X 5 X 1.5
ALUM. WASHER
OPTIONAL PARTS
LANDING GEAR WIRE
PART NO. FK 9655
M2 X36
THREADED PUSH ROD
NOSE GEAR SERVO
3
4
NOSE WHEEL 45 MM
5
MOUNT THE SERVO TRAY
WITH M3 X 12 SOCKET HEAD
TAPPING SCREW
MAIN WHEEL 45 MM
6
M2 X36
THREADED PUSH ROD
BALL LINK
MAIN GEAR SERVO
P.3
MESH TEMPLATE
(SCALE 1:1)
FOR BELL 222 (60)
A
C
D
B
E
E
D
B
C
A
P.4
BELL 222
ENGINE SIZE:60
INSTALLATION OF CENTURY PREDATOR MECHANISM
1
CENTURY PREDATOR
35 MM
65 MM
2
65 MM
43 MM
60 MM
79 MM
50 MM
MOUNTING MECHANISM IN
FUSELAGE WITH SHAPED
HARDWOOD IN PLACE.
CUT VENTILATING HOLE AND MECHANISM
MOUNTING HOLES (3.5 MM) AS SHOWN.
3
10x50 MM PLYWOOD LOCATION
(INSIDE FUSELAGE)
GLUE 10x50 MM PLYWOOD INSIDE FUSELAGE.
ALUM. MOUNTING PLATE WITH M3x10 FLAT HEAD
SCREWS AND LOCK-NUTS.
5
4
CUT AWAY MARKED PORTION FOR SWATCH PLATE.
CUT HOLE FOR STARTING PROBE.
6
34 MM
20 MM
CUT TAIL HATCH FOR GEAR-BOX AS SHOWN.
P.5
BELL 222
ENGINE SIZE:60
INSTALLATION OF HIROBO FREYA MECHANISM
HIROBO FREYA
1
2
17 MM
17 MM
203.5 MM
12.5 MM
83.5 MM
65 MM
83.5 MM
8 MM
CROSS SECTION
55 MM
CUT VENTILATING HOLE AND MECHANISM
MOUNTING HOLES (3.5 MM) AS SHOWN.
3
SAND AWAY SHADED AREA ON PLYWOOD MOUNTING
PLATE AS SHOWN.
4
10x50 MM PLYWOOD LOCATION
(INSIDE FUSELAGE)
MOUNT THE MECHANISM
IN FUSELAGE WITH SANDED
MOUNTING PLATE INVERTED.
5
GLUE 10x50 MM PLYWOOD INSIDE FUSELAGE.
ALUM. MOUNTING PLATE WITH M3x10 FLAT HEAD
SCREWS AND LOCK-NUTS.
6
38 MM
10 MM
CUT AWAY MARKED PORTION FOR SWATCH PLATE.
CUT HOLE FOR STARTING PROBE.
CUT TAIL HATCH FOR GEAR-BOX AS SHOWN.
P.6
BELL 222
ENGINE SIZE:60
INSTALLATION OF THUNDER TIGER RAPTOR MECHANISM
THUNDER TIGER RAPTOR
1
2
212 MM
29 MM
20 MM
58 MM
76.5 MM
50 MM
CROSS SECTION
CUT VENTILATING HOLE AND MECHANISM
MOUNTING HOLES (3.5 MM) AS SHOWN.
3
SAND AWAY SHADED AREA ON PLYWOOD MOUNTING
PLATE AS SHOWN.
4
MOUNT THE MECHANISM
IN FUSELAGE WITH SANDED
MOUNTING PLATE INVERTED.
5
GLUE 10x50 MM PLYWOOD INSIDE FUSELAGE.
ALUM. MOUNTING PLATE WITH M3x10 FLAT HEAD
SCREWS AND LOCK-NUTS.
6
RAPTOR 90 TAIL BOOM
LENGTH: 814 MM
(PART NO. PV-0422)
CUT AWAY MARKED PORTION FOR SWATCH PLATE.
CUT HOLE FOR STARTING PROBE.
7
40 MM
8
10 MM
CUT TAIL HATCH FOR GEAR-BOX AS SHOWN.
P.7
BELL 222
ENGINE SIZE: 60
Below optional retractable landing gears
are available for this helicopter.
PARTS NO.
FK-9606
(1 helicopter needs 3 pcs)
90
NOSE (1 PC)
95
MAIN (2 PC)
PARTS NO.
FK-9655
(3 pcs per set)
Manufactured BY:
FUN-KEY AEROPLANE MODELS & BALSAWOOD MFR.