2016 Sandwich Fair Demolition Derby Rules DeKalb County

2016 Sandwich Fair Demolition Derby Rules
DeKalb County Fairgrounds
1401 Suydam Road
Sandwich, IL
1:00 & 3:00 Shows
September 11th
Gates Open at 8:00 A.M. Cars Need to be Signed in at
11:4SA.M. NO EXCEPTIONS!!
If You Have Any Questions - Please Go To:
wecrash.com
Sandwich Fair Thread
The rules and/or regulations set forth herein are designed to provide for the orderly conduct of
racing events and to establish minimum acceptable requirements for such events. These rules
shall govern the condition of all events, and by participating in these events, all participants are
deemed to have complied with these rules. NO EXPRESSED OR IMPLIED WARRANTY OF SAFETY
SHALL RESULT FROM PUBLICATIONS OF OR COMPLIANCE WITH THESE RULES AND OR
REGULATIONS. They are intended as a guide for the conduct of the sport and are in no way a
guarantee against injury or death to a participant, spectator or official.
The race director shall be empowered to permit reasonable and appropriate deviation from any
of the specifications herein or impose any further restrictions that in his/her opinion does not
alter the minimum acceptable requirements. NO EXPRESSED OR IMPLIED WARRANTY OF
SAFETY SHALL RESULT FROM SUCH ALTERATION OF SPECIFICATIONS. Any interpretation or
deviation of these rules is left to the discretion of the officials. Their decision if final.
GENERAL RULES
FAIR CLASS: No full frame Imperials, No Hearses, No Limousines.See specific rules on pages 2-10
COMPACT CLASS: 111" wheelbase, maximum on front wheel drive and 106" maximum
wheelbase on rear wheel drive. Engine must be (6) cylinder or smaller. No all-wheel drive cars
See specific rules on pages 2-10
allowed.
WIRE CLASS:
See specific rules on pages 2-10
MINI VAN CLASS:
See specific rules on page 11
POWER WHEELS CLASS:
See specific rules on page 12
PURSE PAYOUTS:
See page 13
-1-
1.
z.
An entry fee will be charged for each Driver/Rider'
pit pass
waiver,and release form' and purchase
All persons MUST sign an entry form, insurance
3.
before entering Pit area'
influence of alcohol' POSSESSION OF ALCOHOLIC
No one allowed in r."." area under the
4.
BEVERAGESINTHEPITAREAWILLRESULTINLosSoFPITPASSANDEXPULSIoNFRoMTHEPITS'
Participants 16 & 17 years old MUST have a
All drivers/riders MUST be 16 years or older'
pit person under the age of 18 years old MUST have a
sign a minor and release form.
form before entering pit area' NO EXCEPTIONS!!
'ARENT
PARENT/GUARDIAN sign minor and release
5.Alldrivers/ridersMUSTwearapproverhelmets,longpantsandshirt.
6'Allvehiclesarerecommendedtohavetheircarnumberexhibitedonanuprightnumberplate
serve
15". car numbers are registered first come first
on the roof of the car, minimum of 15" by
basis.Nopre.registerednumbersareallowed'NoPRoFAN|TYwillbeallowed.
lt is suggested that seat belts be tied in a knot at
Drivers must wear approved eye protection'
7.
theappropriateadjustmentastonotallowittokeepretractingonyourwaistduring
comPetition.
8.
'
OR REMOVE ANY AIR BAGS' AII CATS MUST bC
AII TCAT SCATS MUST bC TCMOVCd' DISCONNECT
trunk' No spare tires' broken glass or trash' etc'
swept clean, both drivers compartments and
front seat passenger
9. Battery may be moved, but MUST be securely fastened and covered in
floorboards. No more than two batteries allowed'
chain, etc. running center mast from roof down to
10. All entries MUST have either a bar, wire or
the halo bar'
the firewall. lf a bar is ran; bar cannot contact
position and mounted in rear seat area {trucksL1. stock gas tank MUST be removed from original
or added metal stfaps' NO CHAllls oR RUBBER
behind cab) and secured by existing seat belts
STRAPESorroundbottomtanks.Mountingisnottobedesignedtostrengthen.car.Ametal have
No PLASTIC BOAT TANKS' Alltanks MUST
marine {boat) tank is sTRONGLY recommended'
proof' No M0RE THAN 7 GALLONS OF GAS lN
secure cap. All lines and fittings MUST be leak
pump MusT have some type of shut-off switch easily
TANK. All cars equipped with electric fuel
accessibletodriver.Compactcarswiththefueltankmountedaheadofrearaxlemaychooseto
leave the tank in stock location'
AUTOMOBILE BODY/FRAM E REGULATIONS:
1-. Trailer Hitches, class A or frame mounted MUsT
mounted ,trailer ballstub MUST be cut off'
be totally removed' class B or bumper
T.ALLFRAMESMUSTREMAINoEMsTocKUNLESSoTHERWISEoUTLINEDELSEWHEREINTHESE
THE
OF
TO LIGHTLY RE-WELD THE FRAME SEAMS FORWARD
frame at check in inspection will not be allowed
cA6E ZONE. Any driver Caught With an altered
RULES. YOU WILL 8E ALLOWED
toenterthecar.Anydrivercaughtwithanalteredframeatpostraceinspectionwillforfeitany
winnings.
3.Patchingoftheframewillbeallowedonfreshorper.ranentries.Patchesmustbeexternalof
allowed 24" of patchtotal' cage zone
theframes. No METALINSIDE THE FRAME!!! You willbe
andhumpplateswillnotbecountagainstyourpatchallowance.Asinglepatchwillbeallowed
are staggered' total length will be used
on 2 sides of the frame. lf two sides are used and
than two side, the additional patch will be counted
against 24" allowance. lf patching is on more
WILL BE STRICTLY ENFORCED!!!
against ihe24" allowance. PATCHING ALLOWANCES
-2-
4.
5.
6.
No larger
A lower radiator support may be added between the frame rails in the stock location.
than a 4" piece ofchannel iron.
Seams welding on radiator core support will be allowed. No added metal'
Any OEM bumper and shock canister may be bolted or welded on any car' NO HCIMEMADE
Bumpers skins may be cut, beat down and welded. Holes in bumper skin can be
BUMpERS!ll
1ff'
filled with metal of same thickness. Homemade mounts will be allowed but cannot exceed
HOMEMADE OR OEM MOUNT- NCI WELDING BEYOND LCI"
Of*TO FRAME- Shock tubes on bumpers may be collapsed and welded . lf you choose, frame can
be cut and bumper welded directly to the frame without a bumper mount- TRUCK BUMPER
HEIGHT- Bottom of bumpers 26" MAXIMUM FROM GROUND and 15" MINIMUM. NO
onto the frame.
REGARDT"ESS OF
THIS
RELOCATING OR EXTENDING BUMPERS TO ACHIEVE THIS HEIGHTI! ANY DEVIATION FROM
RULE ON PERRANS WILL SE AT DISCRETION OF THE OFFICIALS'
7,
two bottom) thin straps of metal on the front bumper not
toexceed4"wide x!f4" thick,fromthetopof bumpertonomorethan3"of contactonthe
radiator support. The lower straps must attach to the frame not to extend more than L0" from
the burnper. These stftlps can be substituted with chain/wire. OR You may a non OEM radiator
guard not to exceed 1" beyond core support radiator openingand not contact the bumper. YOU
FRONT- you may weld 4 (two top and
WILL NCIT BE ALLOWED BOTH!II
top and two bottom) thin straps of rnetal on the rear bumper not to
exceed 4" wide xL/4" thick, from the top of the bumper tO nO more than 3" onto the deck
lid/tailgate. The lower straps must attach to frame not to extend more than 10" from the
bumper. These straps can be substituted with chain/wire.
9. All side doors may be welded and reinforced. Externaldoor reinforcing may not extend more
than 6" past the front and rear door seam.
8.
REAR- you may weld 4 (two
CAGES:
CARS- All internal cages
will be limited to specific area: the cage may be installed from firewall to
rear seat area. CAGE CANNOT EXTEf{D BEYOF|O A VERTICAL LINE 12" lN FRONT OF THE CENTER LINE OF
THE REAR AXI-E. Rear of cage may contast but cannot be welded to frame or sheet metal. lnternal cage
supports {down bars} may be welded to top, side orthrough the frame rails. No welding to or on frame
arches front or rear unless outlined elsewhere in the rules. The down tubes MUST stay on the flat part of
theframe within the cage area. lN THE REAR OF CAGE ZONE, ONCE THE FRAME MAKES A SIOCK BEND,
UF OR DOWN THATAREA IS OFF LIMITS UNTESS OUTLINED EIJEWHERE IN THSSE RULES. THE FRONT OF
THE CAGE/DCIWN gAR ZCINE W|LL 8E N0 FURTFIER FORWARS T}{AN A VERTICAL LIFIE ON THE FLAT CIF
Tl{E FIREWALL. No part of the cage will be allowed forward of the firewall. The "down bar area" is your
safety area, do what you wish inside this zone.
-3-
is your safety area do what
box/beds. No shifting box back to gain cage length. The "down bar area"
you wish inside this zone.
,,pitching,, of frames allowed. Any metal added outside of the down bar zone counts against the
24" palch aIlowance when "tilting/pitching"'
This must be
1L. 1 single bar, chain or wire may be run from top rear window to trunk/tailgate'
if a plate is used
within 4,, of the front seam of the trunk lid/top of tailgate. The contact area,
lf a bar is ran: bar cannot
cannot exceed 4,'x4" ontop or bottom of this rear window support.
only on
TRUCKS- This strap will be limited to the cage/down bar zone
10.
contact the halo bar.
pickup trucks (cannot extend to tailgate)'
a single chain, wire
Additionally- Each window opening outside of the cage zone will be allowed
within 4"of window
or 2,, wide steel strap across opening. This wire, strap or chain must attach
the wire or chain to
opening on both ends. A 1" washer may be lightly welded to sheet metalfor
avoid tearing.
with no larger than a 1"
12. Sheet metal body bohs may be replaced but cannot exceed 318' AD
no larger
washer. Each wheel opening will be allowed (10) bolts not to exceedSlS'OD with
the wheel opening'
than a 1,, washer. These bolts may not be further than 4" from the edge of
side of carburetor13. Hoods MUST have two {Z} holes, at least four {4} inches in diameter, on each
BLADE MUST BE
Not directly on top of carburetor. lF HOOD lS REMOVED, EITHER FAN
metalfolded under and
REMOVED OR FAN BELT MUST BE CUT. Hoods holes may have the sheet
have 3/8" bolts
lightly welded L" weld, skip 5", 1" weld , etc. lf no weld is used, hood holes may
are used, bolts
place
lf
bolts
of weld'
with washers no larger than 1" every 6" on edge of hole in
(20) 3/8 bolts with washers no
must be within 1" of edge of hood hole. ln addition you may use
larger than 1" from hood to inner hood support'
method:
14. On all cars, hoods, trunks and tailgates may be secured with the following
ON HOOD;
exceed 1" diameter
A maximum of {10} bolts may be used to secure hood down. The bolts cannot
attached
with a washer no larger than six {6) inches square or lf 4" thick. (a} of these bolts may be
lower
lf
welding
only'
vertically to the frame with the remaining {5} being sheet metal to sheet metal
not
part of bolt to sheet metalfor mounting purpose, weld not exceed 3" on bolt. Frame mounted bolts
piece
long
A
3"
with the exception of a washer on top of radiator support.
to be welded to sheet metal
be lightly welded to sheet
of thin angle iron may be used to mount sheet metal bolts. Washers may
(1" bolts/all
metal. Sleeving of bolts allowed- external diameter of sleeves not to exceed 1" maximum
longer and not
thread cannot be sleeved but may be butt welded to 1" maximum pipe to make bolts
thicker)
ON THE REAR OF CAR;
panels may be cut or pre-bent.
Deck lid/tailgate must remain on stock hinges. Deck lid and quarter
allow adequate room
station wagons/Suburbans roof may be cut or per-bent but if pushed down, must
(4)
1" bolts allowed through roof
for inspection. lf roof is pushed down: No welding allowed, only four
-4-
on "sedagons" only. You may use (20) 3/8 bolts with washers no larger than L" from rear deck to inner
rear deck support.
].5.
SECURE TRUNK/TAILGATE ONE OF
TWO WAYS BELOW:
Method L- Tailgate/truck seam- Trunk seam may be completely welded with 3"x1/8" strap max
with an additional 4 bolts through lid/gate to frame. Bolts cannot exceed 1" diameter with
washers no larger than six (6) inches square or 1"/4 inch thick. Washen may be lightly welded to
sheet metal of deck lid/gate only. Bolts may be through frame or lightly welded vertically along
side.
NOTE THATTHE FRONT OF TRUNK TO PACKAGE TRAY I5 NOT A SEAM AND CANNOT BE
WELDED!!
OR IF NO WELD I5 USED
Method 2- A maximum of (L4) bolts may be used to secure deck lid/tailgate. The bolts cannot
exceed 1" diameter with washers no larger than {6} inches square or I/4 inch thick. Washers
may be lightly welded to sheet metal od deck lid/tailgate only. Four {4) of these bolts may be
attached vertically to frame with the remaining ten (10) being sheet metalto sheet metal only.
The four frame bolts may be through frame or lightly welded along side.
15. Sleeving of bolts allowed- external diameter of sleeves not to exceed 1" maximum {1" bolts/all
thread cannot be sleeved but may be butt welded to 1" maximum pipe to make bolts longer and
thicker).
17. Chain, wire or cable may be installed cross ways between rear frame rails behind rear end in one
place only.
18. Rubber body mounts biscuits may be removed and the body bolted to frame. Stock body mount
bolts can be replaced with bolts no larger than 1" OD and washers no larger than 6" square.
A total of 2 additional body bolts may be added behind the previously mentioned down bar
zone either through existing frame holes or lightly welding a bolt vertically along side of the
frame.
Bottom washers on stock and/or added mounts may be asked to be removed for inspection
purpose. Be prepared to remove them. NO EXCUSES.
19. FOR FAIR CLASS ONLY- You will be allowed a 22" hump plate. The plate may be no more than
1/4" thick and a maximum of 22" in length. 'THIS WltL BE MEASURED FROM CENTER OF HUMP
tl INCHES FORWARD AND 11 INCHES BACK" This plate rnust be cut to contour of frame, placed
in center of hump and this plate must be on outside of frame only. Plate may be bolted or
welded to frame with a single pass weld. lF YOU
PLATE!
LEAF
-
SPRING COVERT YOU CAN NOT HUMP
!
DRIVETRAIN REGU LATIONS:
L.
Any engine or transmission may be used in any car (except compact), but MUST be mounted in a
stock position. On a v- block motor, front spark plugs MUST be even or in front of upper ball
joint. On in-line motors, number two (2) spark plug MUST be even or in front of upper balljoint.
-J-
tr
you may replace the aluminum engine cradles with a stock GM or FORD steel cradle' lt must be
in stock location with weld not to exceed that of the stock installation' All other required
frame' No
components may welded (weld not exceed that of stock installiation) as necessary to
added non- OEM metal, braces or gussets with the exception of a small pipe in which it's only
Z.
3.
4.
purpose is to hold the coii spring in place.
pucks and weld the
Fair class- Chrysler R- body cars may remove the rubber engine mount
mount to the frame. Single pass of weld and NO ADDED METAL'
Distributor protectors allowed but must be designed to protect distributor ONLY' Not to
strengthen car. NO ENFORCING OF FIREWALL!!
for
Chained, welded, or homemade motor mounts will be permitted, but MUST be designed
FINAL.
engine mounting only and not strengthening of car. OFFICIAUS DECISION WILL BE
Any type automobile radiator may be used but MUST be mounted in stock position. At drivers
option he/she may compete without radiator.
A lower radiator support may be added between the frame rails in the stock location' No larger
than 4" piece of channel iron'
Engine cooling system should be drained and flushed free of antifreeze. Air conditioning Freon
MUST be properly evacuated from system. This work MUST be accomplished BEFORE arrival at
race site.
5.
6.
Any type of header is allowed, but MUST be directed away from driver compartment.
Transmission oil coolers permitted. Transmission cooler mounting cannot extend behind cage
zone.
7.
Any driveshaft or u joint may be used. Welding of drive shaft is permitted.
SUSPENSION AND STEERING:
1.
2.
3.
Original suspension components must be used unless specified elsewhere in these rulesSteering components may be strengthened or modified.
Rear differentials may be interchanged; rear differential may be no more than 8 lugs/ studs.
Tilting rear end is allowed. You may chain rear end in 4 spots. Homemade spring perches or
homemade trailing arm brackets may be welded to rear end. No aftermarket solid rims'
Watts- link conversion for FORDS. You may convert a Watts - Link to standard 4 link system in
the following way; Use the upper and lower trailing arms brackets off an older FORD. After
market brackets are allowed, but no thicker than !14" and may be attached with a max of 3-tl2'
bolts each OR a single pass weld on brackets. No positioning of brackets to strengthen the front
down legs of the rear hump. Mounts must be mounted in the similar stock location of which the
installed rear differential was designed for'
4.
5.
Suspension shocks can be replaced with 2" pipe.
Cars may have no more than 14 inches of ground clearance in the middle of the car' Cars/ trucks
originally equipped with leaf springs will not be allowed more than nine {9} leaves in the stack.
Leaves must have 1" stagger with the exception of one leaf equal to the main leaf length and
must consist of all stock leaves. No homemade or flat steel leaves. Stiffness of the suspension
will be left to the discretion of the driver.
-6-
per side' These homemade clamps must be in stock
You may add 4 homemade spring clamps
appearingspringclampsandcannotbemorethan2,,long'Noweldingoftheleaves.
be altred or reinforced in any
CoilSpring Cars- an OEM trailing arm must be used but may
manner.
in a stock looking manor' Leafs can be
Leaf spring conversions are welcome as long as it is done
6.
ontopofrear-endaslongasitpassestheheightrestriction'
cannot exceed height maximum'
Any size rim and tire combination allowed but automobile
SPLIT RIMS ALLOWEDI!
7.
8.
9.
NO
permitted to allow for bolt pattern and
Valve stem protectors okay. Aftermarket centers will be
rimstraightening.Nootherweldingorreinforcingallowed'
in place permitted'
Liquid in tires permitted, studs or screws in rims to hold tires
Doubling of tires allowed.
-7-
WIRE CLASS RULES ARE AS FOLLOWS ;
'
A}TYFI]LLSIZECARSEXCEPTFORTHEFOLLOWING'FULLFRAMEIMPERIALS'OR
0RHEARSES oR TRUCK TYPE
IMPERI,AL sUB FRAME CARS, AMBULANCE,
VEHICLE.
(IJNLIMITED #9 WIRE)
GENERAL SAFETY RULES APPLY.
I.DRIVETRAIN-ANYDRTVETRAINMAYBEUSEDINANYVEHICLE.DRTVETRAIN
CAME WrI.I{
STOCK MOLTNTS OF TF{E SAME STYLE THAT
MUST BE MOTINT;N ON
you are adding 1*lntflgn type cradle
cAR. EVEN rr mjNNrwc A LOWER CRADLE. If
BACK THAN THE
CRADLE, #1 SPARK PLUG MUST TiT NO FURTHER
OR
CONVERSION CRADLE IS
CENTERLINE OF UPi'CN BALL JOINT. {AN ENGINE
AS LONG AS IT DOES NOT
ALLowED IF BoLTED IN PLACE AND NdT WELDED.)
A}IY
sTngNcTHENCAR!!!!JUDGESDECISIONISFINAL!! ar€as of the engine block
A light lswer *adie rnay be usedlllgs to protacl-the^rnouating
PROTECTORS, DP, ECT)
6g. ltO exrgen'rg PRSTSCTOR.S,TRANS
wIT}i A s'*clg BA.KTYPE BRACE- iDo
",riyi
3. ANy 5 LUG REAREND MAy FE {JsEb,
ABSOL{JTELYNC I LUG TRUCK
NOT MODIFy OR STRENGTI-IEN TR.AILIi'IG ARMS]
REAR gN}S!!!!
2,
protector mav not be
NERAT TypE *LIDERS ALLOWED / oR TANK FR*TEC?0R {tank
the back valance. located only in center of
more than 24 inches wide with a 1 inch gap between
seat bar') (NOT BOTH'
be attached to
back seat area. This can not bolt to floor, must
stock
oNg on THE OTHER) A oem type slider is still considered
box only- €4L! lO-tS:
5. After rnarker cotumrl rnay Ae ;rxLtied 6o the steering
STOCK TO THE VEHICLE A
REMAIN
MUST
ETC.
dgDS,
DRAGLINKS, TIE ROD
nnrras MAY BE WELDED I INCHFOR HEIGHT)
L. no Nor REPLAcE oR ADD BoLTs ro FENDERS'
PRorEcToRs wILL BE ALLowED'
T. ANy TIRE nrai ne USED. vALVE STEM
MATERIAL' (CARPET' DO-OII' PANELS'
8. CAR.S MUST BE STRIPPED OF INTERIOR
THE AIR BAGS' ALL
HEADLINER, erC.lHaaY LEAyE DA5H. PLEA5E DISSSNECT
WHEEL WEIGHTS MUST
GLASS AND EXTiiilOR MOLDINCS MUST BE REMOVED,
BE REMOVED
TFM REAR SEAT AREA AND SECURED
9. GAS TANKS MUST BE RELOCATED TO
MEET APPRSyAL oF THE
MUST
iiCHfr-V. {DO NOT UsE BuNcE CSRDS)
4.
back
INSPECTORS.
i.
OF CAR AND SECURED TIGHTLY'
IO.BATTERY MAY BE MOYED TO THE INTERIOR
-8-
11. MUST HAVE SEAT BELTS THAT WORK. (WLL BE CHECKED)
12. TRANS COOLER ALLOWED (BUT MUST BE MOLINTED IN A SAFE
AND SECUF.E
AREA OF THE CAR)
13. HOMEMADE i AFTERMARKET HEADERS. FLOOR SHIFTERS AND GAS PEDAL
WILL BE ALLOWED, TRANS COOLER.
14. AFTERMARKET RADIATORS ALLOWED
15. BUMPERS- ANY OEM AUTOMOTIVE BUMPERS ALLOWED SHOCKS CAN BE
COLLAPSED AND WELDED. YOU CAN BEAT THE CHROME DOWN AND LICHTLY
SKIP _ WELD SKIN TO BACKING. NO RENFORCEMENT TO THE OUTSIDE OF THE
BUMPER, NO OTHER WELDING ON BUMPER 1S ALLOWED. A SHORT CHAIN MAY
BE WRAPPED AROIIND BUMPER AND BOLTED TO FRAME IN TWO PLACES.
YOU MAY WELD AROT'ND THE SHOCK MOTINTING BRACKETS ON TFfE BUMPER
TO HOLD THE FRONT BUMPER ON. YOU CAN ADD ANY SHOCK TYPE MOUNTED
BRACKET TO A HARD NOSE TYPE CAR IN STOCK POSITION, WITH NO ADDED
METAL.
/YOU CAN WELD BUMPER TO FRAME WITH NO OTHER SHOCK "BUTT WELD'' IF
DESIRED ,YOU MAY ADD TWO PIECES 4 INCH BY 4 INCH % INCH, ON EACH SIDE
OF FRAME AT BUMPER CONNECTTNG AREA IF MOUNTING THIS WAY./
16. CHRYSLER V- BUMPERS ALLOWED ONLY ON CAR THEY CAME WITH.
17. NO CHRYSLER SHOCKS ON GM CARS.
18. NO SHOCKS IN FRAME LINLESS THEY CAME STOCK THERE. DO NOT SLIDE
BUMPER BACK AND WELD TO FRAM WHEN ADDING BUMPER SHOCKS.{WELDED
TO ONE OR THE OTHER)
19. THE ONLY OTHER WELDING THAT CAN BE DONE ON THE CARS IS THE
FOLLOWING: YOU MAY WELD THE SPIDER GEARS EEAR DIFFERENTIAL)
DRIVERS DOOR AND PASSENCERS FRONT DOOR MAY BE WELDED ON THE DOOR
FRONT AND BACK SEAMS OF TFIE DOORS WITH A MAX PIECE OF STRAP NO MORE
THAN 4'' WIDE 12 INCHES LONG AND 1I8'' THICK. LOWER ENGINE MO{.INTS MAY
BE WELDED TO FRAME IN ORDER TO MOTINT ENGINE IN CAR, BUT IN NO WAY
CAN IT BE MOUNTED TO F{ELP STRENGHTHEN CAR!!! IF YOU WELD ANYTHING
OTHER THAN THE ABOVE SPECIFIED YOU WILL NOT RLIN IN THE WIRE CLASS,
YOU CAN RLTN IN THE OTHER CLASSES.
20. SAFETY CAGES: CAGES CAN BE NO MORE THAN 6'' iN DIAMETER, YOU ARE
ALLOWED A SEAT BAR AND A DASH BAR. YOU CAN CONNECT THESE BARS SIDE,
STDE CAGE BARS CAN NOT EXTEND PAST THE REAR BODY MOLINT, IN FR.ONT OF
THE BACK SEAT AREA OF ANY FORD OR GM MADE AUTOMOBILE, AND THE
FRONT LEAF SPRING BRACKET OF ANY CHRYSLER OR I.EAFED SPRUNG
AUTOMOBILE.
ROLL-OVER BARS ALLOWED NO FURTHER BACK TH,dN 4'' BEHIND DRIVE,RS SEAT
TO CAGE ONLY NOT FLOOR TINLESS COMPETING iN A NON.POST CAR, THEN
SHEET METAL ONI,Y!! ALL CAGE COMPONENTS WELD TO SHEET.METAL ONLY!!!
EXCEPT TANK PROTECTOR IF RLINNING ONE.
21. DOORS, HOODS, TRUNKS: HOODS MUST HAVE TWO 4'' HOLES CUT ON THE
SIDES OF THE CARBURATOR. ALL DOORS MUST BE SECURED WITH AT LEAST I
CHAIN OR 2 PIECES OF # 9 WIRE OR YOU WILL NOT RI.'N!!!!
22. RADIATOR OR CORE SUPORT BOLT'S MAY BE REPLACED WITH UP TO %
THREADED ROD, TFIESE CAN EXTEND THROUGH THE HOOD AND BOLTED DOWN.
23. TUCKING OF THE TRI.'NK AND NOTCHING OF FRAME WILL BE ALLOWED
24. SPRING SPACERS WILL BE ALLOWED BUT MUST MEET APPROVAL OF
OFFICIALS.
25. YOU CAN CHAIN REAR END DOWN
-9-
THE REAR OF
26. A WTRE OR CI-IAIN CAN BE RAN BETWEEN THE FRAME RAILS ON
CAR.
27.''NO MODIFICATION TO BODY MOUNTS''
where u wire r
"N0 ADDED METAL WELDED TO WIRE CARSI!!" includes washers
not allowed!!
-1 0-
MINI VAN RULES
1.
to build
who wants
This class is very stock and intended for the beginner or someone
vehicle' No welding
vehicle in a day ortwo. No additional work may be done to the
except safety bars and the driver's door'
a
-
front wheel drive only allowed'
2.
Rear wheel drive or
3.
Vehicle must be left completely factory stock
4.
flammable
Alltrailer hitches, glass, chrome, plastic, molding; A/C coolant, antifreeze and
may be left in or
materialfrom inside and outside of the vehicle must be removed- Dash
- except as noted below'
be rernoved.
5.
be mounted in the rear
Stock gas tank must be removed and a small metaltank must
due to the fuel
seat aiea. The tank must be very secure and covered. An original tank
be very
must
willbe allowed. Tank mounting, covering and system
injection system
safe. Use of properly rated lines only. Plastic tanks are not allowed'
6.
but must have
Electronic fuel system will be allowed if vehicle came factory installed,
an easy to reach switch that must be clearly marked "Onf OIY '
7. Transmission shifrer may be modified
-floor
shifters are allowed -ignition may be hot-
wired.
g.
Hood must have a
g.
per door.
Doors are to be chained or wired shut in a maximum of two places
!2"x!2" minimum hole to easily extinguish engine fires.
10. Hood, trunk & tailgate must be chained or wired shut in two places'
11. Battery must be relocated to the inside of the vehicle, secured and covered. One
battery per vehicle allowed.
i.2.
to each
Dash bar and seat bars are allowed for driver's safety. Bars may be connected
other with door bars. Bars may not extend past the firewall and may not extend
not tie into
rearward beyond the front most part of the rear wheel well tubs. Bars may
the floor, rear frame humps, drive train or frame'
13. Factory installed drive fiain must be used. Exhaust headers through the hood are
allowed.
14. Any tire or wheel can be used.
ALL VEHICLES MUST HAVE A LEGIBLF NUMBER ON A
ROOF MOUNTED SIGN.
-1 1-
POWER WHEELS RULES
L.
Must wear seat belt.
2.
Must have doors for protection.
3.
Must wear helmet * bicycle style is permitted.
4.
No altering of tires. May use Duck Tape to repair tires.
5.
Kids must wear long pants and enclosed shoes
6.
No larger than a lawn & garden battery will be permitted. 12 volts maximum.
7.
Battery must be securely fastened.
8.
Always obey the flag person.
9.
Have Fun!
-1 2-
-
no sandals allowed.
2AL5 SAND\A'ICH FAIR DEMOLITION DERBY PAYOUTS
Sto,ooo
rorAl
PURSE
Mini Van Class: 51.000
Lrt
Ssoo.oo
2nd
s2so.00
$rzs.oo
s7s.00
$so.oo
3rd
Arh
5th
Compact Class: 51,800
Lrt
s800.00
2nd
ss00.00
3rd
Szso.oo
$rso.oo
$roo.oo
4th
5th
Wire Class: 53,600
Lrt
St,8oo.oo
4th
Sgoo.oo
Ssoo.oo
Szso.oo
5th
Srso.oo
2nd
3rd
Fair Class: $3.600
Ltt
2nd
5t,Boo.oo
$goo.oo
3rd
Ssoo.oo
4rh
$zso.oo
$rso.oo
5th
Trophies and/or Plaques will be Awarded to the Top Three in Each Class and all
Payouts are Guaranteed.
Depending Upon the Number of Entries - Additional Heat Money will be Added
to the Above Purses in Each Class.
-1 3-