30092014 Annex B

Regionale workshop Spice3
in samenwerking met SBE
30 september 2014 Chemelot
Best Practices
Energie besparen met
simpele maatregelen
Naam presentator
Functie presentator
Programma Regionale Workshop SPICE3
30 september 2014 Chemelot
Toelichting op het SPiCE3 initiatief en het Platform
Concept Service Boulevard
Isolatie – ‘n vergeten onderwerp en gemiste kansen ?
Peter Stulen / Hertel
Energie management – Hoe staat het er mee?
Theo Tolboom /USG
Energiemanagement – de aanpak bij Lanxess en AkzoNobel
Ronald Huyps (Lanxess) en Ruud Morssinkhof (AkzoNobel)
Efficiënte aandrijvingen – ‘n nieuwe Best Practice
Maarten van Werkhoven / TPA adviseurs
Discussie, vragen en kennisuitwisseling
SPiCE³
‘Sectoral Platform in Chemicals for Energy Efficiency Excellence’
25/09/2014
Author: MBe
SPiCE³ – Objectives
• Facilitate access to energy efficiency information, tools
and support schemes
• Enable companies to take up tools and participate in
existing initiatives
• Promote best practices and success stories
• Establish and strengthen contacts
between energy efficiency actors
to create a network for learning
and exchange
SPiCE³ – Country project partners
April 2012: 11 national
Chemical associations join
SPiCE³ as partners under
the IEE programme
October 2013: UIC (F) &
FEIQUE (E) become
cooperative partners of
SPiCE³ (at own costs)!
Different involvement levels:
•
Online platform + workshops +
on-site training
•
Online platform + workshops
•
Online platform
Case studies – the Kolb case – the impossible made possible
Recovery of heat of reaction in batch processes in a Dutch company
In continuous processes, the recovery of heat of reaction can easily be made part of the plant's heat
integration set-up. In batch processes this not the case, because the heat-in and heat-out flows do not occur
at the same time. Batch processes generally have a sequence of heating up (starting the reaction) and
subsequently cooling down (removing the heat of reaction and maintaining the required reaction
temperature).
In some batch processes, the heat of reaction can be quite high e.g. in ethoxylation reactions. A solution
might be the installing of heat buffer systems. This is, in principle, a rather simple technique, but it is quite
difficult to make it work under practical production conditions.
#
#
#
#
#
#
#
Capacity control rotating
equipment
#
Varable speed drives
Motor drives
#
High effciency motors
Compressed air
#
Steam boilers
#
Steam Systems
Care +
Steam traps and condensate
return
Best Practices
the Netherlands
RVO Ministry Economic
Affairs
DCMR Environmental
Authority
AkzoNobel
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
BE NL
BE FR
UK
#
Germany
VCI
Umwelt Bundesambt
Dena (German Energy
Agency)
#
BEST PRACTICE Cover-note
TITLE: Best practices in Compressed Air production for process, instrument and general utility uses
SUMMARY OF BEST PRACTICE
In the design and operation of compressed air systems a number of guidelines must be followed to ensure an energy
efficient operation. These rules address the choice of compressors, additional apparatus, the lay-out of the system and
the control system as well as the type of use of compressed air and the systems maintenance.
KEY ISSUES TO CONSIDER
The age of a system is an important issue.
Since process installations are generally updated, changed, debottlenecked etc. over time an older system is more likely
not to have a good match with the compressed air demand .
The choice of whether or not to use compressed air for certain application and of what quality also has a great influence
on costs (compressed air is an expensive broom)
Regular maintenance and inspection is vital ! Air leakages may run up to 20-30 % of air production, causing an 20-30 %
higher electricity use
DOs and DON’Ts
Regular inspect the system for air leakages. A 20 % loss in a 30 m3/min system will cost you approx. €25.000 /year
Be sure to select the right air quality for the right uses.
Be sure of the right compressors configuration and flow control (the optimum combination of off/on and frequency
control)
Avoid high pressure drops in the system. 1 bar overpressure in a 10 bar system will result in a increase in electricity use of
approx. 8 %
Approx. 90 % of the energy used is converted into heath, around 65 % of this heath can be recovered and used for heating
purposes
Choose the air inlet point with the lowest possible temperature (1 % energy savings/3 degrees lower temperature) but
avoid dirty or wet conditions.
Vereniging van de Nederlandse Chemische Industrie
T 070 337 87 32
Loire 150, 2491 AK Den Haag
Postbus 443, 2260 AK Leidschendam
www.vnci.nl | [email protected]
Naam presentator : Hans Spaans
[email protected]