060504 SL-650 Usermanual final eng.cdr

User manual
SL-650
ic audio
Control unit for six zones
… to make people listen
Status 05/2006
SL-650
Control unit - front -
Control unit - rear -
EN
2
ic audio
Content
Preperation
Unpacking 5
ic audio
Device Functions
- Rear Side -
Safety Instructions 5
Desktop Mounting 5
100V INPUT 7
Fuse 500mA 7
220V Mains Connection 7
100V OUTPUT 7
INPUT Chime 7
Top view of all functions 8
Device Functions
-Front side-
Further Information
Technical Specifications 8
Further techn. details 8
Volume Control 6
Jumper-Settings 9
LED - Display 6
Block Plugging Diagram 10
Chime - Button 6
Index 11
EN
3
Preperation
ic audio
Unpacking
Please note the unpacking instructions.
- Unpacking
- Safety Instructions
- Desktop Mounting
Safety Instructions
Please note the safety instructions before
connecting the SL-650.
Desktop Mounting
Please note the positioning of the SL-650.
EN
4
Preperation
Unpacking
ic audio
Safety instructions
Please verify if the following parts were delivered:
!
line cord
The wires of the main power line have the following
colours:
GREEN and YELLOW:
(E)
BLUE:
(N)
BROWN :
(L)
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug
proceed as follows:
The wire which is coloured green and yellow must
be connected to the terminal which is marked by
the letter E or by the safety earth symbol or
coloured green and yellow. The wire which is
coloured blue must be connected to the terminal
which is marked with the letter N or coloured
black. The wire which is coloured brown must be
connected to the terminal which is marked with the
letter L or coloured red.
Desktop Mounting
Put the control unit in a position with enough space
enough fresh air to minimise the heat in the
system.
false
Do not place the SL-650 close to of heat sources
or a heater.
Do not expose the SL-650 sunlight or heavy dust.
5
EN
Device Functions
- Front side -
Volume Control
Volume Control
You can adjust the Volume of the 6 zones by
turning the knobs on the front panel to the
favoured position (6x50W, 100V).
ic audio
LED - Display
Chime - Button
LED - Anzeige
The LED-Display shows the operational readiness
of the control unit.
All transformers are equipped with an override
relais for maximum safety.
Chime - Button
By pressing this button you can activate the chime.
Please note: These function is only available after
the installation of a chime module. Alternatively
you can also install another module type instead of
a chime module.
EN
6
Device Functions
- Rearside -
ic audio
100V OUTPUT
100V INPUT 100V INPUT
INPUT Chime Module
220V Main Connection
Bridge
ZONE 1 (100V)
ZONE 2 (100V)
Fuse (500mA)
ZONE 3 (100V)
ZONE 4 (100V)
ZONE 5 (100V)
ZONE 6 (100V)
100V INPUT
You can connect one mixer amplifier or one power
amplifier with each 100V INPUT.
By switching the jumper settings on the main
board you can distribute the signals to the prefered
zone.
Fuse 500mA
To prevent short-circuits.
100V OUTPUT
There are six different 100V loudspeaker outputs
available. Just connect your speakers with the
prefered input.
INPUT Chime Module
The control unit is prepared for the installation of a
chime-module.
220V Mains Connection
The control unit is factory set at 220 V(AC) mains
voltage. Ensure yourself that the device is
connected with this voltage.
7
EN
Device Functions
- Rearside -
Top view of all functions
Technical Specifications
Further techn. details
2 U desktop housing in black with an anodised front platel
Front:
6 Volume Controls
1 ON/OFF-switch
Rear:
1 220V power plug with fuse
4 x 6 contact Wago-strips:
2 INPUTS 100V (6 contacts for 100V EV1 and EV2 + emergency signal )
for additional installation:
Chime modul (provided by customer)
Control + NF (8 contacts)
6 x 100V speaker OUTPUTS (12 contacts)
EN
8
ic audio
Futher
information
ic audio
Jumper-Settings
By setting the jumpers you can define which
amplifier is connected to the volume control of
each ouput zone.
Set the jumper on the EV 1 position for amplifier
one or on the EV 2 position for amplifier 2.
Repeat the procedure for each ouput zone.
The jumpers for the emergency signal will override
all other signals. The emergency signal will be
delivered with maximum volume to the output
zone. To activate this function simply set the
jumpers on the circuit-board on the postions Vorr.
1, Vorr. 2 ..... Vorr. 6 for each output zone.
Layout circut board
Jumper for amplifier selection
Jumper for emergency signal
9
EN
Futher
information
ic audio
EN
10
ic audio GmbH
Mai 2006
Projekt: Reglerfeld 6-fach
Block Plugging Diagram
ic audio
INDEX
A 100V INPUT 7
S Safety Instructions 5
100V OUTPUT 7
220V Mains Connection 7
B Block Plugging Diagram 10
T Technical Specifications 8
Top view of all functions 8
C Chime-Button 6
DDesktop Mounting 5
U Unpacking 5
V Volume Control 6
F Further techn. details 9
Fuse 500mA 7
I
INPUT Chime-module 7
J Jumper-Settings 9
L LED - Display 6
ic audio
www.ic-audio.com
EN
11
ic audio GmbH
Boehringerstraße 14a
68307 Mannheim /
Germany
Fon:+49(0)621/ 77096-0
Fax:+49(0)621/ 77096-26
www.ic-audio.com
Email: [email protected]
ic audio
… to make people listen