daaaaaaaaaa - Industrial GP

Transcription

BALL BEARINGS
INTRODUCTION
EXTRA SMALL SERIES
Extra small bearings are available in the 30 Metric Series, the 33 and S Inch Series
and the F Flanged Series. These bearings can sustain radial, thrust and combined
loads proportionate to the capacities of the small shafts for which they are designed.
They are appropriate for use in fractional horsepower motors, precision instruments,
domestic appliances, film projectors and similar devices.
The F flanged series has external shoulders with the bearing for mounting in
through-bored housings. This series is used where compactness is essential or where
it is not feasible to machine housing shoulders.
All series in the extra small family include shielded versions. The 30 Metric Series
is also available with felt seals, Mechani-Seals and rubber seals, while the 33 and
S Inch Series is available with rubber seals.
Some sizes in the Extra Small Series are manufactured from stainless steel.
Extra small 33 and S series business machine bearings
Standard and special extra small bearings are available and often used in business
machine applications. They include clamp-type collar bearings for slip-fit mounting
on shafts, bearings with Wireloc in the outer ring, and rubber cushioned “O” series
with special housed units.
D
A
EXTRA LIGHT 9300 AND 9100 SERIES
Bearings in the Extra Light 9300 and 9100 Series are ideally suited for applications
where housing diameters are restricted and it is desirable to maintain relatively large
shaft diameters. Both series are made in the Conrad or non-filling slot construction
with the 9300 Series having a somewhat thinner section.
The 9100 Series is generally available with shields, rubber seals and snap ring
combinations. The 9300 Series is selectively available with two rubber seals. Machine
tools, textile machinery and jet engine gear boxes are some of the end products in
which these series have found wide use.
LIGHT 200 SERIES
A
A
Extra Small Series
Bearings in the 200 Series have a greater section height than the Extra Light 9300 and
9100 Series bearings and feature a close dimensional balance between bore, outside
diameter and width. These characteristics make them well-suited for a broad range of
applications involving light to medium loads combined with relatively high speeds.
Their versatility has made them a popular design choice of designers and has
resulted in many variations in the series. They are available in either the Conrad or
maximum capacity type and with shields, rubber seals, Mechani-Seals, felt seals or
a combination of shield and seal. Snap ring combinations are also included.
Wide-type 200 Series rubber seal (W200PP) and Mechani-Seal (W200KLL) bearings
are made with standard bores and outside diameters, but in widths equal to the
corresponding sizes of double-row bearings. This series offers a larger support area
for shaft and housing contact and extra space for lubricant.
Extra Light 9300 and
9100 Series
Light 200 Series
MEDIUM 300 SERIES
A
•
A
The 300 Series radial ball bearings are similar in construction to the 200 Series, but
have considerably heavier cross sections throughout. They provide greater radial and
thrust capacity and are able to withstand heavier shock loads.
Because of their rugged construction, these bearings are particularly suited
for heavy-duty applications like those found in large electric motors, woodworking
machinery and gear boxes. This series includes both Conrad and maximum capacity
designs as well as shielded, sealed and snap ring variations.
In the 300 Series wide-type, rubber seal (W300PP) and Mechani-Seal (W300KLL)
bearings are made with standard bores and outside diameters, but in width equal to
the corresponding sizes of double-row bearings.
D4
TIMKEN PRODUCTS CATALOG
Medium 300 Series
Radial and Angular Contact Ball Bearings
XLS AND EXTRA LARGE 100 SERIES
Bearings in the inch-dimension XLS Series and metric-dimension Extra Large 100
Series have extra large diameters and a compact cross section. XLS bearings are
made in the Conrad and maximum capacity filling slot designs. The Extra Large 100
Series offers the maximum capacity, filling slot and counterbore types.
XLS and Extra Large
100 Series
TRI-PLY SEAL DISK HARROW BEARINGS
Bearings with Tri-Ply Seals are designed for service involving severe contamination,
such as disk harrows, disk tillers and other seed preparation equipment and certain
conveyor applications. Tri-Ply sealed units come in two designs – one consisting of
three Timken rubber seals separated by steel spacers and retained by steel caps in
the outer ring and the other, a highly effective one-piece, molded seal design. Both
designs have an exterior shroud cap to protect the seals and reinforce the exceptional
sealing action of the complete unit. A patented notched seal groove design, provided on
selected sizes, is one of the most positive seal retention methods ever developed.
Tri-Ply Seal
Disk Harrow
Bearings
HEX BORE BEARINGS
These bearings are designed for either outer or inner ring rotation in low speed,
moderately loaded applications such as farm machinery and conveyors. Their chief
advantage is ease of mounting. Except for axial positioning by adjacent parts, no
collars, setscrews or other external parts are required to lock the inner ring to the
hex shaft.
DA
Hex Bore Bearings
R-SEAL DISK HARROW BEARINGS
R-Seal bearings are designed for a wide variety of farm machinery applications
where single-lip positive contact seals are required. Each sealing element has a
Timken Fafnir rubber seal that effectively seals the bearing with a heavy flare on the
cylindrically ground O.D. (inner ring). A steel back-up plate supports the seal rubber
and prevents the seal lip from inverting. An outside metal shroud cap gives maximum
abrasion protection to the rubber element and completes the assembly that is rolled
into the outer ring seal groove for positive retention.
R-Seal radial ball bearings are used in positions in planting, cultivating and harvesting
machinery. They are available in various configurations including round bores in metric
and inch dimensions and cylindrical and spherical outside diameters.
A
R-Seal
Agricultural
Bearings
A
ANGULAR CONTACT – SINGLE-ROW 7000 PRODUCT FAMILY
Timken offers a 7200WN Light, 7300WN Medium and 7400WN Heavy Series singlerow, angular contact bearings, which are designed for combination loading with
high-thrust capacity in one direction.
The 7000WN bearings are manufactured with better than ABEC 1 inner ring bore
tolerances and ABEC 3 running accuracy. These bearings, when mounted in a duplex
arrangement, provide axial and/or radial rigidity in applications where control of shaft
displacement is essential.
These bearings are available with various cage designs as defined in the
dimension tables. The external dimensions of all 7000WN bearings interchange with
corresponding sizes in the 200, 300 and 400 single-row radial series.
A
Single-Row Angular
Contact Bearings
7000 Product Family
ANGULAR CONTACT – DOUBLE-ROW
A
Double-Row
Angular Contact
A
D5
•
Double-row Angular Contact Bearings are available in the Light 5200 and Medium
5300 Series. These bearings have the same bores and outside diameters as the
corresponding sizes in the 200 and 300 Series, single-row, radial type.
Chief advantages of the double-row type are rigidity, compactness and high
capacity. The two rows of balls provide for bearings large radial capacity combined
with moderate thrust capacity in either direction.
Double-row bearings are available in both the Conrad (K) construction with
uninterrupted race shoulders and the maximum capacity type. The latter has a filling
slot in the shoulder of both rings and a maximum ball complement.
Sizes with the W suffix have the filling slot on one side only. In these cases, thrust
should be applied on the side opposite the filling slot.
BALL BEARINGS
Extra Small 30 Metric Series
• Offer various combinations of shields and seals, as listed
below.
• Electric motor quality for applications where quietness is
required.
• Stainless steel series, denoted by a prefix A before the
• Designed for small shafts.
• Can sustain radial, thrust and combined load proportionate
to capacities of small shafts.
• Suitable for use in fractional horsepower motors, domestic
appliances, precision instruments and similar devices.
bearing number. (Example: A38K)
D
One Shield
D
Two Shields
DD
Two Rubber Seals
PP
One Rubber Seal
P
Open
A
A
A
A
Open and shielded types
dimensions
– tolerances
Bearing Number
Bore
Outside Width
Fillet
Wt.
Static
Load
open one shield two shield
d
Diameter
C
Radius(1)
D
DD
D tolerance
Rating
+0.000 mm
Co
+.000 mm, -0.008 mm
+0.0000"
+0.00 mm, -.12 mm
+0.0000", -0.0003"
to minus
+0.000", -0.005"
Extended
Dynamic
Load
Rating
CE (2)
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs.
N
lbs.
34K
35K
36K
37K
38K
34KD
35KD
36KD
37KD
38KD
34KDD
35KDD
36KDD
37KDD
38KDD
4
5
6
7
8
0.1575
0.1969
0.2362
0.2756
0.3150
16
19
19
22
22
0.6299
0.7480
0.7480
0.8661
0.8661
0.008
0.009
0.009
0.009
0.009
0.0003
0.00035
0.00035
0.00035
0.00035
5
6
6
7
7
0.197
0.236
0.236
0.276
0.276
0.3
0.3
0.3
0.3
0.3
0.012
0.012
0.012
0.012
0.012
0.005
0.009
0.009
0.009
0.009
0.01
0.02
0.02
0.02
0.02
560
865
865
1400
1400
125
195
195
312
312
1630
2450
2450
3650
3650
365
560
560
830
830
38KV
39K
—
39KD
—
39KDD
8
9
0.3150
0.3543
24
26
0.9449
1.0236
0.009 0.00035
0.009 0.00035
7
8
0.276
0.315
0.3
0.3
0.012
0.012
0.018
0.018
0.04
0.04
1370
1960
305
440
3650
5000
830
1120
(1) Maximum shaft or housing fillet radius that bearing corners will clear.
(2) Based on 106 revolutions of calculated fatigue life.
sealed types
dimensions
– tolerances
Bearing Number
Bore
d
one seal two seals +0.000 mm, -.008 mm
P
PP
+0.0000", -.0003"
Outside Width
Fillet
Wt.
Static
Load
Diameter
C
Radius(1)
D
Rating
+.000 mm, -.009 mm +0.00 mm, -.12 mm
C o
+0.0000", -.00035"
+0.000", -0.005"
Extended
Dynamic
Load
Rating
CE (2)
mm
in.
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs.
N
lbs.
36P
36P2
37P
37P2
38P
36PP
36PP2
37PP
37PP2
38PP
6
6
7
7
8
0.2362
0.2362
0.2756
0.2756
0.3150
19
19
22
22
22
0.7480
0.7480
0.8661
0.8661
0.8661
10
6
10
7
10
0.394
0.236
0.394
0.276
0.394
0.3
0.3
0.3
0.3
0.3
0.012
0.012
0.012
0.012
0.012
0.014
0.014
0.018
0.018
0.018
0.03
0.03
0.04
0.04
0.04
865
865
1370
1400
1370
195
195
305
312
305
2450
2450
3650
3650
3650
560
560
830
830
830
38P2
39P
38PP2
39PP
8
9
0.3150
0.3543
22
26
0.8661
1.0236
7
8
0.276
0.315
0.3
0.6
0.012
0.024
0.018
0.023
0.04
0.05
1400
1960
312
440
3650
5000
830
1120
•
A
D6
Extra Small 30 Metric Series
MECHANI-SEALS
• Developed by The Timken Company.
• Adapted to the 30 metric series for effective grease retention
and exclusion of foreign matter.
• Can be operated at speeds comparable to open-type bearings.
• Available with:
®
• One Mechani-Seal (suffix L).
• One Mechani-Seal and one shield (suffix LD).
• Two Mechani-Seals (suffix LL).
One Seal
One Seal and Shield
L
LD
Seal Protection Inner
Wt.
Fillet
(1)
DIMENSIONS – TOLERANCES
Bearing Number
Two Seals
LL
Bore
d
one
+0.000 mm
seal
one
and two
-0.008 mm
seal
shield seals
+0.0000"
L
LD
LL
-0.0003"
Outside Width
Ring Width
Static
Ring
Load
Diameter
+0.00 mm, -.12 mm
Radius (2)
Rating
D
+0.000" -.005:"
Offset +0.000 mm
Co
-0.009 mm
+0.0000"
inner
outer
width
O.D.
B
B2(3)
C
E
P
K
-0.00035"
B1
36KL
36KVL
37KL
37KVL
38KL
38KVL 38KVLD 38KVLL
—
—
38KLL2
—
—
38KVLL2
39KL2 39KLD2 —
— 39KVLD 39KVLL2
mm in.
36KLD 36KLL
—
—
37KLD 37KLL
37KVLD —
38KLD 38KLL
mm in.
mm in.
mm in.
6
6
7
7
8
0.2362
0.2362
0.2756
0.2756
0.3150
19
24
22
24
22
0.7480
0.9449
0.8661
0.9449
0.8661
10.310.406
10.310.406
10.310.406
10.310.406
10.310.406
9.80 0.386 14.27 0.562
9.80 0.386 — —
9.80 0.386 14.27 0.562
9.80 0.386 — —
9.80 0.386 14.27 0.562
mm
in.
8
8
8
9
9
0.3150
0.3150
0.3150
0.3543
0.3543
24
22
24
26
30
0.9449 10.310.406 9.80 0.386
0.8661 — —
— —
0.9449 — —
— —
1.0236 10.310.406 9.80 0.386
1.1811 — —
— —
14.27
12.62
12.62
—
16.41
0.562
0.497
0.497
—
0.646
mm in.
mm in.
mm in.
8.00
8.00
8.00
8.00
8.00
0.315
0.315
0.315
0.315
0.315
0.3
0.3
0.3
0.3
0.3
0.012
0.012
0.012
0.012
0.012
9.60 0.378 10.87 0.428
9.60 0.378 — —
9.60 0.378 11.18 0.440
9.60 0.378 — —
9.60 0.378 11.18 0.440
mm
in.
8.00
8.00
8.00
8.00
9.00
0.315
0.315
0.315
0.315
0.354
0.3
0.3
0.3
0.6
0.6
0.012 9.60 0.378
0.012 — —
0.012 — —
0.024 9.60 0.378
0.024 — —
11.13
11.18
11.13
—
15.98
0.438
0.440
0.438
—
0.629
mm in.
16.7
19.0
18.7
19.0
18.7
21/32
3/4
47/64
3/4
47/64
19.0 3/4
18.7 47/64
19.0 3/4
21.4 27/32
25.4 1
mm
in.
kg lbs.
N lbs.
0.50
0.50
0.50
0.50
0.50
0.020
0.020
0.020
0.020
0.020
0.014 0.03
0.022 0.05
0.018 0.04
0.022 0.05
0.018 0.04
865 195
865 195
1400 312
1400 312
1400 312
0.50 0.020 0.022 0.05 1370 305
— — 0.022 0.05 1370 305
— — 0.022 0.05 1370 305
0.50 0.020 0.022 0.05 1960 440
0.50 0.020 0.041 0.09 2650 595
(3) Two seals (suffix LL) type only.
(2) Does not apply to bearings with two seals.
Extended
Dynamic
Load
Rating
CE (4)
N
lbs.
2450
2450
3650
3650
3650
560
560
830
830
830
3650 830
3650 830
3650 830
50001120
65501500
DA
A
Note: Inner ring offset is .51 mm (.020 inches) for the L, LD, and VLD versions.
FELT-SEALS
• Provide effective barrier against the entrance of foreign
matter and the escape of lubricant.
• Contact seal with the felt riding on the ground surface of
inner ring O.D.
• Can be operated at moderate speeds without excessive
heating because the felt washer absorbs some lubricant.
• Electric motor quality where quietness is required.
• Available with:
A
A
• One felt seal (suffix T).
• One felt seal and one shield (suffix TD).
• Two felt seals (suffix TT).
DIMENSIONS
– TOLERANCES
One Felt Seal
T
Two Felt Seals
TT
One Felt Seal and Shield
TD
Bearing Number
Bore
d
+0.000 mm
one
one seal two
-0.008 mm
seal and shield seals
+0.0000"
-0.0003"
T
TD
TT
Outside Ring Width
Inner
Fillet
Wt.
Static
Load
Diameter
+0.00 mm, -.12 mm
Ring
Radius(1)
(2)
+0.000" -.005"
Offset Rating
D
+0.000 mm
C o
-0.009 mm
+0.0000"
inner
outer
-0.00035"
B
C
C1
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs.
N
lbs.
36KTD 36KTT
36KVTD —
37KTD
—
37KVTD —
38KTD 38KTT
6
6
7
7
8
0.2362
0.2362
0.2756
0.2756
0.3150
19
24
22
24
22
0.7480
0.9449
0.8661
0.9449
0.8661
9.80
9.80
9.80
9.80
9.80
0.386
0.386
0.386
0.386
0.386
10.31
10.31
10.31
10.31
10.31
0.406
0.406
0.406
0.406
0.406
14.27 0.562
—
—
—
—
—
—
14.27 0.562
0.50
0.50
0.50
0.50
0.50
0.020
0.020
0.020
0.020
0.020
0.3
0.3
0.3
0.3
0.3
0.012
0.012
0.012
0.012
0.012
0.014
0.027
0.018
0.022
0.018
0.03
0.06
0.04
0.05
0.04
865
1370
1370
1370
1370
195
305
305
305
305
2450
3650
3650
3650
3650
560
830
830
830
830
38KVTD 38KVTT
39KTD 39KTT
39KVTD —
8
9
9
0.3150
0.3543
0.3543
24 0.9449
26 1.0236
30 1.1811
10.31 0.406
11.51 0.453
12.70 0.500
14.27 0.562
14.27 0.562
—
—
0.50 0.020
0.40 0.016
0.50 0.020
1370 305
1960 440
2650 595
3650
5000
6550
830
1120
1500
0.3 0.012
0.6 0.024
0.6 0.024
0.022 0.05
0.027 0.06
0.041 0.09
(2) Does not apply to bearings with two seals.
D7
•
9.80 0.386
11.10 0.437
12.19 0.480
in.
A
36KT
36KVT
37KT
37KVT
38KT
38KVT
39KT
39KVT
mm
Extended
Dynamic
Load
Rating
CE (3)
A
BALL BEARINGS
Extra Small 33 and S Inch Series
• Designed for small shafts.
• Can sustain radial, thrust and combined loads, proportionate to capacities of small shafts.
• Suitable for use in fractional horsepower motors, domestic
appliances, precision instruments and similar devices.
• Include combinations of shields and seals, as listed below.
• Electric motor quality for applications where quietness is
required.
• Several sizes are manufactured both in standard bearing-quality
dd
D
D
d
D
steel and stainless steel, as indicated in the tables.
C
C
C
Bearing Number
Bore
Outside Width
Fillet
Wt.
Static
Load
d
Diameter
C
Radius(1)
tolerance
D tolerance
Rating
+0.000 mm
+0.000 mm
CO
+0.000"
+0.000"
+0.000 mm, -0.13 mm
to minus
to minus
+0.000, -0.005"
D
A
in.
Extended
Dynamic
Load
Rating
CE (2)
standard
stainless
mm
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs.
N
lbs.
33K3
33K4
33K5
S1K7
S1K
A33K3
A33K4
A33K5
AS1K7
AS1K
3.175
3.175
4.762
6.350
6.350
0.1250
0.1250
0.1875
0.2500
0.2500
0.008
0.008
0.008
0.008
0.008
0.0003
0.0003
0.0003
0.0003
0.0003
9.525
12.700
12.700
15.875
19.050
0.3750
0.5000
0.5000
0.6250
0.7500
0.010
0.010
0.010
0.010
0.010
0.0004
0.0004
0.0004
0.0004
0.0004
3.96
4.37
3.96
4.98
5.56
0.156
0.172
0.156
0.196
0.219
0.3
0.3
0.3
0.3
0.4
0.012
0.012
0.012
0.012
0.016
0.005
0.005
0.005
0.005
0.009
0.01
0.01
0.01
0.01
0.02
212
490
490
560
1160
48
110
110
125
260
710
1430
1430
1630
3100
160
325
325
365
695
S3K
S5K
S7K
S8K
S9K
AS3K
AS5K
AS7K
—
—
9.525
12.700
15.875
19.050
22.225
0.3750
0.5000
0.6250
0.7500
0.8750
0.008
0.008
0.008
0.010
0.010
0.0003
0.0003
0.0003
0.0004
0.0004
22.225
28.575
34.925
41.275
47.625
0.8750
1.1250
1.3750
1.6250
1.8750
0.010
0.010
0.013
0.013
0.013
0.0004
0.0004
0.0005
0.0005
0.0005
5.56
6.35
7.14
7.92
9.52
0.219
0.250
0.281
0.312
0.375
0.4
0.4
0.8
0.8
0.8
0.016
0.016
0.031
0.031
0.031
0.009
0.018
0.032
0.050
0.064
0.02
0.04
0.07
0.11
0.14
1400 312
2240 500
3050 682
4400 1000
4900 1120
3650
5600
7500
10400
11000
830
1270
1700
2320
2500
S10K
S11K
S12K
—
—
—
0.013 0.0005
0.013 0.0005
0.013 0.0005
9.52
9.52
9.52
0.375
0.375
0.375
0.8
0.8
0.8
0.031
0.031
0.031
0.082
0.091
0.100
0.18
0.20
0.22
4900 1120
5400 1220
6000 1340
11000
11800
12200
2500
2650
2750
25.400 1.0000
28.575 1.1250
31.750 1.2500
0.010 0.0004
0.010 0.0004
0.013 0.0005
50.800 2.0000
53.975 2.1250
57.150 2.2500
A
A
A
SHIELD AND SEAL COMBINATIONS
One
One
One
Shield
Shield
Shield
DD
D
One
Standard
Shield Two
One
Shield
Shields
D
D
DD
Two
Two
Two
Shields
Shields
Shields
DD
DD
DD
One
One
OneShield
Shield
Shield
And
AndSeal
Seal
Seal
And
PD
PD
PD
Two
Stainless
Shields Two
One
Width
Shield
Shields
+0.00 mm, -.12 mm
DD
D
DD
+0.000", -.005"
mm
in.
33KD3
33KD4
33KD5
S1KD7
S1KD
33KDD3
33KDD4
33KDD5
S1KDD7
S1KDD
S3KD
S5KD
S7KD
S8KD
S9KD
S3KDD
S5KDD
S7KDD
S8KDD
S9KDD
AS3KD
AS5KD
—
—
—
AS3KDD
AS5KDD
—
AS8KDD
—
7.14
7.92
8.74
11.13
12.70
0.281
0.312
0.344
0.438
0.500
S10KDD
—
—
—
—
—
12.70
—
0.500
—
S10KD
—
•
A
D8
A33KD3
—
A33KD5
AS1KD7
AS1KD
A33KDD3
—
A33KDD5
AS1KDD7
AS1KDD
3.96
4.37
4.98
4.98
7.14
0.156
0.172
0.196
0.196
0.281
One Shield
Seal
One And
Shield
And Seal
PD
PD
Two
Seals
PP
Two
Two
Two
Seals
Seals
Seals
PP
PP
PP
Two
Seals
Two Seals
PP (Wireloc)
PPG
in.
5/32
11/64
—
—
9/32
9/32
5/16
11/32
7/16
1/2
1/2
—
Two
Two
TwoSeals
Seals
Seals
WIRELOC
WIRELOC
Wireloc
PPG
PPG
PPG
Two Seals
WIRELOC
PPG
Width
+0.00 mm, -.12 mm
+0.000", -.005"
mm
in.
in.
—
—
—
—
—
33PP3
—
33PP5
S1PP7
S1PP
—
—
33PPG5
S1PPG7
S1PPG
3.96
—
4.98
4.98
7.14
0.156
—
0.196
0.196
0.281
5/32
—
S5PD
—
S8PD
—
S3PP
S5PP
S7PP
S8PP
—
S3PPG
S5PPG
—
—
—
7.14
7.92
8.74
11.13
—
0.281
0.312
0.344
0.438
—
9/32
—
—
S10PP2
S12NPP
—
—
12.70
12.70
0.500
0.500
—
—
—
9/32
5/16
11/32
7/16
—
1/2
—
E
E
Flanged Series
CYLINDRICAL O.D.
• Four sizes offered in flanged construction.
• Integral shoulders for mounting in through-bored housings.
• Straight outside diameters.
• Interchangeable with corresponding unflanged sizes.
• Available with double shields.
• Electric motor quality for applications where quietness
D
d
H
J
D
A
d
H
A
is required.
C
C
Open Type
Shielded Type
Bearing Number
Bore
Outside
Width
Inner Ring FlangeShielded Type
Wt.
Static
Extended
d
Diameter
C
Shoulder
Overall
Load
Dynamic
chamfer
D
Width
Rating
Load
Rating
J x 45°
A
CO
+0.000 mm +0.25 mm
+0.000 mm
+0.00 mm
+0.13 mm
+0.00 mm
CE 2)
-0.008 mm -0.00 mm
-0.010 mm
-0.13 mm
-0.05 mm
E
-0.13 mm
+0.0000”
+0.010”
+0.000”
+0.000”H
+0.005” ±0.05 mm
+0.000”H
open
shielded*
-0.0003”
-0.000”
-0.0004"
-0.005”
Min.
-0.002”
±0.002”
-0.005”
Min.
lbs.
mm in.
mm in.
mm in.
mm in.
mm in.
mm in.
mm in.
mm in.
mm in.
kg lbs.
N lbs.
N
(
F33K3
F33K5
FS1K7
FS3K
F33KDD3
F33KDD5
FS1KDD7(1)
FS3KDD(1)
3.175
4.762
6.350
9.525
0.1250
0.1875
0.2500
0.3750
0.30
0.30
0.30
0.41
0.012
0.012
0.012
0.016
9.525 0.3750
12.700 0.5000
15.875 0.6250
22.225 0.8750
3.96
3.96
4.98
5.56
0.156
0.156
0.196
0.219
5.13
6.86
8.86
13.13
0.202
0.270
0.349
0.517
11.18
14.35
17.53
24.61
0.440
0.565
0.690
0.969
0.76
1.07
1.07
1.57
0.030
0.042
0.042
0.062
3.96
4.98
4.98
7.14
0.156
0.196
0.196
0.281
4.65
6.30
8.43
12.06
0.183
0.248
0.332
0.475
0.005
0.005
0.005
0.009
0.01
0.01
0.01
0.02
212
490
560
1400
48
110
125
310
710
1430
1630
3650
160
325
365
830
DA
(1) Also available in stainless steel. To specify, add prefix "A" before bearing number. (2) Based on 106 revolutions of calculated fatigue life.
* Also available with two contact seals. To specify, replace "KDD" in part number with "PP".
TAPERED O.D.
•
F
F
• F Flanged series has shoulders integral with the bearings for
mounting in through-bored housings.
• Used where compactness is essential or where it is not
desirable to machine housing shoulders.
• All sizes in series have tapered outside diameters and are
available with double shields.
• Suitable applications include precision instruments,
packaging machinery and motion picture projectors.
• Several sizes in the series are manufactured in both standard
J
D
d
B
bearing-quality, chromium-alloy, high-carbon steel and
stainless steel (stainless steel specified by suffix “A”).
Electric motor quality where quietness is required.
A
E
E
H
A
J
D
d
B
C
C
Open Type Shielded Type
H
A
A
Bearing Number
Bore
Outside
Ring Widths Flange
Wt.
Static
Extended
d
Diameter
Inner
Outer
Load
Dynamic
chamfer
D
Width
Rating
Load
CE (4)
J x 45°
Inner
C
A
CO
+.00 mm
+0.13 mm
+0.008 mm +0.025 mm
+0.000 mm
Width
ProjectH(3)
-0.00 mm -.00 mm
-0.10 mm
B
F
-0.10 mm
Taper
-0.05 mm
E
+0.0003” +0.010”
+0.000”
±0.3 mm
±0.13 mm
+0.000"
Per
+0.005” ±0.05 mm
openshielded
-0.0000” -0.000”
-0.0004"
±0.010"
-0.005”
Min.
-0.004”
Foot
-0.002” ±0.002"
F2(1)
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
0.1875
0.1250
0.1875
0.1875
0.2500
0.25
0.25
0.25
0.25
0.25
0.010
0.010
0.010
0.010
0.010
11.130
9.534
14.305
14.305
15.893
0.4382
0.3757
0.5632
0.5632
0.6257
4.80
4.77
5.54
6.35
6.35
0.189
0.188
0.218
0.250
0.250
0.41
0.38
0.38
0.38
0.38
0.016
0.015
0.015
0.015
0.015
6.93
4.60
6.93
6.22
8.41
0.273
0.181
0.273
0.245
0.331
4.14
4.14
4.95
5.74
5.74
0.163
0.163
0.195
0.226
0.226
2.03
1.90
2.03
1.73
1.73
0.080
0.075
0.080
0.068
0.068
12.70 11.13 15.88 15.88 17.45 —
F3
—
F4
—
F2DD-2
—
F3DD
F4DD
4.762
3.175
4.762
4.762
6.350
F5
F5DD(2)
7.938 0.3125
0.25 0.010 17.480 0.6882 6.35 0.250
0.38 0.015
10.41 0.410(2) 5.74 0.226
1.73 0.068
in.
mm
in.
0.500 1.07 0.042
0.438 0.94 0.037
0.625 1.07 0.042
0.625 1.07 0.042
0.687 1.07 0.042
19.05 0.750
(1) Full type, no retainer. Not suggested for speeds over 500 RPM.
(2) H dimension is 9.68 mm (.381") for F5DD.
(3) Land dimension of the inner ring.
1.07 0.042
kg
lbs.
N
lbs.
N
lbs.
0.005
0.005
0.005
0.005
0.005
0.01
0.01
0.01
0.01
0.01
465
212
490
490
560
106
48
110
110
125
1160
710
1430
1430
1630
260
160
325
325
365
865 196
2400
540
0.005 0.01
A
D9
•
A
A
BALL BEARINGS
ST Flangette Unit
• Pressed steel housed units designed for light-duty applications.
• Available in shaft sizes from 6.35 mm - 12.7 mm (1/4 to 1/2 inch).
• Designed to simplify mounting on side plate or frame-type housings.
• Two identical steel stampings house a clamp-type bearing with a
spherical O.D. outer ring.
• Spherical inside surface of each stamping mates with the spherical
O.D. of the bearing, providing initial self-alignment at mounting.
• Offers features of basic clamp-type bearing.
• Available with sealed or shielded construction.
• Radial load capacity is 25 percent of basic bearing’s dynamic load
rating at 33.3 RPM.
• Inspected to ABEC-1 tolerances, except bore.
• Suggested shaft tolerance: Nominal bore size to -.0005 in. resulting in
D
M
G
A1 STOCK
THICKNESS
BOLT HOLE DIA. "N"
2 HOLES - 180° APART
SET
SCREW
H
d1
J
H2
MIN.
FRAME
OPENING
d
L
.000 in. to .001 in. loose-shaft fit.
A
Unit Number
Bore**
Set-
M
G
A1H
L
J
N
screw
d
A
d1H2
+0.13 mm
Thread*
-0.000 mm
+0.0005"
-0.0000"
mm
in.
S1PPB7-3 ST 6.350 0.2500
S3PPB15 ST 7.937 0.3125
S5PPB2 ST 12.700 0.5000
mm in.
5.556 7/32
7.144 9/32
7.937 5/16
mm
in.
mm in.
mm
in.
mm
14.287 9/16 19.844 25/32 10.922 0.430
19.844 25/32 27.781 13/32 14.275 0.562
23.019 29/32 32.544 19/32 15.875 0.625
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm in.
2.007 0.079 0.683 0.0269 45.244 1 25/32 22.225 7/8 30.956 1 7/32 0.219 7/32
2.718 0.107 0.836 0.0329 53.181 2 3/32 30.163 1 13/16 38.894 1 17/32 0.219 7/32
3.048 0.120 0.912 0.0359 59.531 2 11/32 36.512 1 17/16 45.244 1 25/32 0.219 7/32
4-40
8-36
8-36
Max.
Radial
Unit
Load
N
lbs.
312 70
668 150
980 220
* All setscrews are hex socket oval point, six fluted socket setscrews available upon request. **Bore tolerance applies prior to collar assembly.
Setscrews with fused plastic patch available at added cost.
A
B
SET
SCREW
RTF-Rubber Tire Flange Housed Unit
• Synthetic, conductive elastomer of Durometer hardness 80-85
A
A
•
•
•
•
•
•
•
A
facilitates mounting of standard cylindrical O.D. bearings in side plate
of frame-type housings.
Generous taper on entrance corner of rubber cartridge simplifies
insertion of unit into side panel, assuring reasonable squareness of
bearings when fully mounted.
Bearing is positioned by integral flange of the rubber cartridge.
Resiliency of elastomer accommodates wider than the standard
suggested housing bore tolerance.
Greater flexibility in adjusting to minor shaft and/or housing alignment.
Helps reduce airborne noise and structural vibration.
Additional advantages are similar to features of basic clamp-type
bearing design.
Due to deflection characteristics of the elastomer, radial and thrust
ratings for the RTF Series are 10 percent of the basic bearing’s
dynamic load rating at 33.3 RPM.
Unit Number
C
d
d1
E
G
H
Bore** D
Set-
E
B
GH
screw
d RTFHSG
C
d1
+0.13 mm O.D. Bore
Thread*
-0.000 mm
+0.0005"±0.13 mm±0.13 mm
-0.0000" ±0.005" ±0.005"
mm
in.
6.350 0.2500
7.937 0.3125
9.525 0.3750
12.700 0.5000
mm
in.
mm
in.
mm
in.
mm
in.
19.355
27.280
27.280
35.255
0.762
1.074
1.074
1.388
19.050
26.975
26.975
34.925
0.750
1.062
1.062
1.375
13.494
19.050
19.050
25.400
17/32
14.287
19.844
19.844
23.019
9/16
3/4
3/4
1
25/32
25/32
29/32
mm
in.
22.225 7/8
30.956 17/32
30.956 17/32
38.894 117/32
mm
in.
11.906 15/32
15.875 5/8
15.875 5/8
17.859 45/64
mm in.
1.984
3.969
3.969
3.969
5/64
5/32
5/32
5/32
mm
7.541
10.319
10.319
11.906
in.
19/64
13/32
13/32
15/32
4-40
8-36
8-36
8-36
Max.
Radial
Unit
Load
N
lbs.
116
258
258
392
26
58
58
88
* All setscrews are hex socket oval point, six fluted socket setscrews available upon request. **Bore tolerance applies prior to collar assembly.
Setscrews with fused plastic patch available at added cost.
•
A
S1PP73RTF
S3PP16RTF
S3PP4RTF
S5PP2RTF
D
D10
Special Bearings
• Pulley, guide roller and pinch roll bearings:
• Available in several bore sizes.
• Lightweight, low inertia, low torque and accurate running
characteristics with minimum runout and wobble.
• Many units feature outer ring assemblies with integral
molded tires.
• Most common tire materials are aluminum, steel and a
variety of engineered plastics such as nylon, polycarbonate,
acetal resin or polyurethane.
• Tire material and configuration are determined by
application requirements.
• Standard materials and shapes can be made in many sizes.
• Timken engineering may assist in testing materials you feel
are suitable for your applications.
• Timken universal ring design:
1/ 2
± 1/ 64
TO CLEAR .016R
BOTH SIDES
1.005
.995 .7500
.7496
.657
MAX.
REF.
.2500
.2495
.2812
.2762
.334
MIN.
REF. 5
/8
REF.
S1KDD-RT
• Sealed or shielded versions readily available in the most
basic bearing sizes.
• Varying degrees of seal drag, to suit the sealing torque
requirements dictated by the environmental conditions
of the application.
DA
• Integral assembly design concept:
• Complete package of bearings, housings, shafts, etc.
• Assembled and ready to mount.
• Custom designed to solve customer assembly problems
and minimize inventory of multiple components.
• Overall cost savings.
• Bearing units shown have been developed especially for
business machine applications.
A
A
A
A
D11
•
A
BALL BEARINGS
Ultra Light 9300K Series
• Designed for applications where housing diameters are restricted and
it is desirable to maintain relatively large shaft diameters.
• Resembles the 9100K Series, except corresponding sizes of the 9300K
Series have a somewhat thinner section.
• Used extensively in machine tools, textile machinery and jet engine
d
D
gearbox applications.
C
Bearing Bore Outside Width
Fillet Wt.
Static
Load
Number
d Diameter
C
Radius(1)
tolerance
D tolerance
tolerance
Rating
+0.000 mm +0.000 mm
+0.000 mm
Co
+0.0000"
+0.0000"
+0.0000"
to minus
to minus
to minus
D
Extended
Dynamic
Load
Rating
CE (4)
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs.
N
lbs.
9301K
9302K
9303K(2)
9305K(2)
9306K(2)(3)
12
15
17
25
30
0.4724
0.5906
0.6693
0.9843
1.1811
0.008
0.008
0.008
0.010
0.010
0.0003
0.0003
0.0003
0.0004
0.0004
24
28
30
42
47
0.9449
1.1024
1.1811
1.6535
1.8504
0.009
0.009
0.009
0.011
0.011
0.00035
0.00035
0.00035
0.00045
0.00045
6
7
7
9
9
0.236
0.276
0.276
0.354
0.354
0.12
0.12
0.12
0.12
0.12
0.005
0.005
0.005
0.005
0.005
0.3
0.3
0.3
0.3
0.3
0.012
0.012
0.012
0.012
0.012
0.014
0.018
0.027
0.045
0.075
0.03
0.04
0.06
0.10
0.16
1600
2270 2540
4540
4980 360
510
570
1020
1120
3650
4890
5250
8010
8270
830
1100
1180
1800
1860
9307K
9308K
9310K
9311K
9313K
35
40
50
55
65
1.3780
1.5748
1.9685
2.1654
2.5591
0.012
0.012
0.012
0.015
0.015
0.00045
0.00045
0.00045
0.0006
0.0006
55
62
72
80
90
2.1654
2.4409
2.8346
3.1496
3.5433
0.013
0.013
0.013
0.013
0.015
0.0005
0.0005
0.0005
0.0005
0.0006
10
12
12
13
13
0.394
0.472
0.472
0.512*
0.512*
0.12
0.12
0.12
0.15
0.15
0.005
0.005
0.005
0.006
0.006
0.6
0.6
0.6
1.0
1.0
0.024
0.024
0.024
0.039
0.039
0.095
0.141
0.168
0.209
0.250
0.21
0.31
0.37
0.46
0.55
8010 8900 11560 14010 16010 1800
2000
2600
3150
3600
13300
13800
16700
18900
19600
3000
3100
3750
4250
4400
9316K
80
3.1496
0.015 0.0006
110
4.3307
0.015 0.0006
16
0.630*
0.15
0.006
1.0
0.039
0.363 0.80
24020 5400
28500
6400
* Width tolerance is +.00 mm to -.15 mm (+.000" to -.006").
(2) Also available with rubber seals, e.g., 9303PP.
(3) Also available with two shields, e.g., 9306KDD.
A
Extra Light 9100K Series
•
•
A
d
D
applications where housing diameters are restricted and
For
it is desirable to maintain relatively large shaft diameters.
Electric motor quality for applications where quietness is a
requirement.
C
Fillet Wt.
Static
Load
Number
d Diameter
C
Radius(1)
tolerance
D tolerance
tolerance
Rating
+0.000 mm +0.000 mm
+0.000 mm
Co
+0.0000"
+0.0000"
+0.0000"
to minus
to minus
to minus
A
A
A
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs.
9100K
9101K
9102K
9103K
9104K
10
12
15
17
20
0.3937
0.4724
0.5906
0.6693
0.7874
0.008
0.008
0.008
0.008
0.010
0.0003
0.0003
0.0003
0.0003
0.0004
26
28
32
35
42
1.0236
1.1024
1.2598
1.3780
1.6535
0.009
0.009
0.011
0.011
0.011
0.00035
0.00035
0.00045
0.00045
0.00045
8
8
9
10
12
0.3150
0.3150
0.3543
0.3937
0.4724
0.12
0.12
0.12
0.12
0.12
0.005
0.005
0.005
0.005
0.005
0.3
0.3
0.3
0.3
0.6
0.012
0.012
0.012
0.012
0.024
0.018
0.018
0.027
0.041
0.073
0.04
0.04
0.06
0.09
0.16
1960
2360
2800
3200
5000
440
530
630
720
1120
5160
5870
6360
6800
10700
1160
1320
1430
1530
2400
9105K
9106K
9107K
9108K
9109K
25
30
35
40
45
0.9843
1.1811
1.3780
1.5748
1.7717
0.010
0.010
0.012
0.012
0.012
0.0004
0.0004
0.00045
0.00045
0.00045
47
55
62
68
75
1.8504
2.1654
2.4409
2.6772
2.9528
0.011
0.013
0.013
0.013
0.013
0.00045
0.0005
0.0005
0.0005
0.0005
12
13
14
15
16
0.4724
0.5118
0.5512
0.5906
0.6299
0.12
0.12
0.12
0.12
0.12
0.005
0.005
0.005
0.005
0.005
0.6
1.0
1.0
1.0
1.0
0.024
0.039
0.039
0.039
0.039
0.077
0.118
0.145
0.195
0.249
0.17
0.26
0.32
0.43
0.55
5740
8010
9960
12200
14900
1290
1800
2240
2750
3350
11300
14600
18000
20000
24000
2550
3350
4050
4500
5400
9110K
9111K
9112K
9113K
9114K
50
55
60
65
70
1.9685
2.1654
2.3622
2.5591
2.7559
0.012
0.015
0.015
0.015
0.015
0.00045
0.0006
0.0006
0.0006
0.0006
80
90
95
100
110
3.1496
3.5433
3.7402
3.9370
4.3307
0.013
0.015
0.015
0.015
0.015
0.0005
0.0006
0.0006
0.0006
0.0006
16
18
18
18
20
0.6299
0.7087
0.7087
0.7087
0.7874
0.12
0.15
0.15
0.15
0.15
0.005
0.006
0.006
0.006
0.006
1.0
1.0
1.0
1.0
1.0
0.039
0.039
0.039
0.039
0.039
0.272
0.390
0.417
0.445
0.630
0.60
0.86
0.92
0.98
1.39
16000
20700
22600
24500
29800
3600
4650
5100
5500
6700
24900
32000
33400
34700
43200
5600
7200
7500
7800
9720
9115K
9116K
9117K
9118K
9119K
9120K
75
80
85
90
95
100
2.9528
3.1496
3.3465
3.5433
3.7402
3.9370
0.015
0.015
0.020
0.020
0.020
0.020
0.0006
0.0006
0.0008
0.0008
0.0008
0.0008
115
125
130
140
145
150
4.5276
4.9213
5.1181
5.5118
5.7087
5.9055
0.015
0.018
0.018
0.018
0.018
0.018
0.0006
0.0007
0.0007
0.0007
0.0007
0.0007
20
22
22
24
24
24
0.7874
0.8661
0.8661
0.9449
0.9449
0.9449
0.15
0.15
0.20
0.20
0.20
0.20
0.006
0.006
0.008
0.008
0.008
0.008
1.0
1.0
1.0
1.5
1.5
1.5
0.039
0.039
0.039
0.059
0.059
0.059
0.680
0.885
0.966
1.157
1.188
1.315
1.50
1.95
2.13
2.55
2.62
2.90
32700
35600
35600
48000
52500
52500
7350
8000
8000
10800
11800
11800
44500
54300
56500
66700
68100
68100
10000
12200
12700
15000
15300
15300
•
Extended
Dynamic
Load
Rating
CE (2)
D12
N
lbs.
Continued on the next page.
Extra Light 9100K Series
(continued)
Fillet Wt.
Static
Load
Number
d Diameter
C
Radius(1)
tolerance
D tolerance
tolerance
Rating
+0.000 mm +0.000 mm
+0.000 mm
Co
+0.0000"
+0.0000"
+0.0000"
to minus
to minus
to minus
in.
mm
in.
mm
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs.
9121K
9122K
9124K
9126K
9128K
105
110
120
130
140
4.1339
4.3307
4.7244
5.1181
5.5118
0.020
0.020
0.020
0.025
0.025
0.0008
0.0008
0.0008
0.0010
0.0010
160
170
180
200
210
6.2992
6.6929
7.0866
7.8740
8.2677
0.025
0.025
0.025
0.030
0.030
0.0010
0.0010
0.0010
0.0012
0.0012
26
28
28
33
33
1.0236
1.1024
1.1024
1.2992
1.2992
0.20
0.20
0.20
0.25
0.25
0.008
0.008
0.008
0.010
0.010
2.0
2.0
2.0
2.0
2.0
0.079
0.080
0.079
0.079
0.080
1.6
—
2.2
3.4
3.6
3.6
—
4.9
7.4
8.0
59600
71100
71100
90700
105000
13400
16000
16000
20400
23600
76900
92500
88900
115600
124500
17600
20800
20000
26000
28000
9130K
9132K
9134K
9136K
9138K
150
160
170
180
190
5.9055
6.2992
6.6929
7.0866
7.4803
0.025
0.025
0.025
0.025
0.030
0.0010
0.0010
0.0010
0.0010
0.0012
225 8.8583
240 9.4488
260 10.2362
280 11.0236
290 11.4173
0.030
0.030
0.035
0.035
0.035
0.0012
0.0012
0.0014
0.0014
0.0014
35
38
42
44
46
1.3780
1.4961
1.6535
1.8110
1.8110
0.25
0.25
0.25
0.25
0.30
0.010
0.010
0.010
0.010
0.012
2.0
2.0
2.0
2.0
2.0
0.080
0.080
0.080
0.080
0.080
5.5
6.7
9.0
11.0
12.0
12.0
14.8
19.8
24.3
26.5
92500
138000
160000
195700
204000
20800
31000
36000
44000
45500
113400
166800
189000
222000
216000
25500
37500
42500
50000
48000
9140K
9144K
9146K
9152K
9156K
200 7.8740
220 8.6614
240 9.4488
260 10.2362
280 11.0236
0.030
0.030
0.030
0.035
0.035
0.0012
0.0012
0.0012
0.0014
0.0014
310
340
360
400
420
0.035
0.040
0.040
0.040
0.045
0.0014
0.0016
0.0016
0.0016
0.0018
51
56
56
65
65
2.0079
2.2047
2.2047
2.5591
2.5591
0.30
0.30
0.30
0.35
0.35
0.012
0.012
0.012
0.014
0.014
2.0
2.5
2.5
3.0
3.0
0.080
0.100
0.100
0.120
0.120
15.4
20.0
21.5
31.6
33.5
34.0
44.2
47.3
69.6
73.8
245000
290000
320000
400000
355000
55000
65500
72000
90000
80000
245000
280000
290000
345000
360000
55000
63000
65500
78000
80000
9160K
9164K
9180K
300 11.8110
320 12.5984
400 15.7480
0.035 0.0014
0.040 0.0016
0.040 0.0016
0.045 0.0018
0.045 0.0018
0.050 0.0020
74
74
90
2.9134
2.9134
3.5433
0.35 0.014
0.40 0.016
0.40 0.016
3.0
3.0
4.0
0.120
0.120
0.160
46.6 102.9
49.1 108.3
—
—
12.2047
13.3858
14.1732
15.7480
16.5354
460 18.1102
480 18.8976
600 23.6220
N
Extended
Dynamic
Load
Rating
CE (2)
lbs.
520000 118000
570000 127000
815000 180000
415000 93000
430000 98000
550000 122000
DA
Shields, Seals and snap ring combinations
A
OFFSET
Snap Ring (Wireloc)(1)
Shields and Seals THICKNESS
O.D.
One
Shield
D
Two
Shields
DD
One
Seal
P
Two
Seals
PP
One Shield
And Seal
PD
Open
Type
G
Two
Shields
DDG
Two Seals
PPG
O.D.
Thickness
Offset
mm
in.
mm
in.
mm
in.
9100KD
9101KD
9102KD
9103KD
9104KD
9100KDD
9101KDD
9102KDD
9103KDD
9104KDD
9100P
9101P
9102P
9103P
9104P
9100PP
9101PP
9102PP
9103PP
9104PP
9100PD
9101PD
—
9103PD2(2)
—
—
—
9102KG
9103KG
9104KG
—
—
9102KDDG
9103KDDG
9104KDDG
—
—
9102PPG
9103PPG
9104PPG
—
—
36.5
39.3
46.0
—
—
1 7/16
1 35/64
1 13/16
—
—
1.07
1.07
1.07
—
—
0.042
0.042
0.042
—
—
3.05
3.05
3.05
—
—
0.120
0.120
0.120
9105KD
9106KD
9107KD
9108KD
9109KD
9105KDD
9106KDD
9107KDD
9108KDD
9109KDD
9105P
9106P
9107P
9108P
9109P
9105PP
9106PP
9107PP
9108PP
9109PP
—
9106PD
—
—
9109PD
—
9106KG
9107KG
9108KG
9109KG
—
9106KDDG
9107KDDG
9108KDDG
9109KDDG
—
9106PPG
9107PPG
9108PPG
9109PPG
52.4
60.3
67.5
74.2
81.4
2 1/16
2 3/8
2 21/32
2 59/64
3 13/64
1.07
1.07
1.65
1.65
1.65
0.042
0.042
0.065
0.065
0.065
3.05
3.05
3.63
4.04
4.04
0.120
0.120
0.143
0.159
0.159
9110KD
9111KD
9112KD
9113KD
9114KD
9110KDD
9111KDD
9112KDD
9113KDD
9114KDD
9110P
9111P
9112P
9113P
9114P
9110PP
9111PP
9112PP
9113PP
9114PP
—
—
—
9113PD
—
9110KG
9111KG
9112KG
9113KG
9114KG
—
—
—
—
—
—
9111PPG
—
9113PPG
—
86.5
96.4
101.2
106.4
116.3
3 13/32
3 51/64
3 63/64
4 3/16
4 37/64
1.65
2.41
2.41
2.41
2.41
0.065
0.095
0.095
0.095
0.095
4.04
5.18
5.18
5.18
5.18
0.159
0.204
0.204
0.204
0.204
9115KD
—
9117KD
—
—
9120KD
9115KDD
—
—
—
—
—
9115P
—
—
—
—
—
9115PP
—
—
—
—
9120NPP
—
—
—
—
—
—
—
—
9117KG
—
—
—
—
—
9117KDDG
—
—
—
—
—
—
—
—
—
121.4
—
139.7
—
—
159.5
4 25/32
—
5 1/2
—
—
6 9/32
2.41
—
2.77
—
—
2.77
0.095
—
0.109
—
—
0.109
5.18
—
5.54
—
—
6.35
0.204
—
0.218
—
—
0.250
9121KD
—
9124KD
—
—
—
—
—
—
—
—
—
9124P
—
—
—
—
9124PP
—
—
—
—
—
—
—
—
—
9124KG
—
—
—
—
—
—
—
—
—
—
—
—
169.5
—
192.9
—
—
6 43/64
—
7 19/32
—
—
2.77
—
3.05
—
—
0.109
—
0.120
—
—
6.35
—
6.63
—
—
0.250
—
0.261
—
—
(2) Width of bearing is 12.700 mm (.5000").
D13
•
(1) The snap ring is normally packaged separately in the box with bearing.
A
A
A
A
BALL BEARINGS
Light 200K Series
• Conrad-type bearing is well-balanced, with deep races and
•
•
uninterrupted race shoulders. Excellent, general-purpose
bearing.
Capacity to carry radial and thrust in either direction or
combined loads.
Electric motor quality for applications where quietness is a
requirement.
d
D
C
Fillet Wt.
Static
Load
Number
d Diameter
C
Radius(1)
tolerance
D tolerance
tolerance
Rating
+0.000 mm +0.000 mm
+0.000 mm
Co
+0.0000"
+0.0000"
+0.0000"
to minus
to minus
to minus
D
A
A
A
A
mm
in.
mm
in.
mm
in.
mm
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs.
N
lbs.
200K
201K
202K
203K
204K
10
12
15
17
20
0.3937
0.4724
0.5906
0.6693
0.7874
0.008
0.008
0.008
0.008
0.010
0.0003
0.0003
0.0003
0.0003
0.0004
30
32
35
40
47
1.1811
1.2598
1.3780
1.5748
1.8504
0.009
0.011
0.011
0.011
0.011
0.00035
0.00043
0.00043
0.00043
0.00043
9
10
11
12
14
0.3543
0.3937
0.4331
0.4724
0.5512
0.12
0.12
0.12
0.12
0.12
0.005
0.005
0.005
0.005
0.005
0.6
0.6
0.6
0.6
1.0
0.024
0.024
0.024
0.024
0.039
0.027
0.036
0.041
0.064
0.104
0.06
0.08
0.09
0.14
0.23
2600
3000
3470
4700
6500
585
680
830
1060
1460
6800
7600
8650
10900
14400
1530
1730
1930
2450
3250
205K
206K
207K
208K
209K
25
30
35
40
45
0.9843
1.1811
1.3780
1.5748
1.7717
0.010
0.010
0.012
0.012
0.012
0.0004
0.0004
0.00047
0.00047
0.00047
52
62
72
80
85
2.0472
2.4409
2.8346
3.1496
3.3465
0.013
0.013
0.013
0.013
0.015
0.0005
0.0005
0.0005
0.0005
0.0006
15
16
17
18
19
0.5906
0.6299
0.6693
0.7087
0.7480
0.12
0.12
0.12
0.12
0.12
0.005
0.005
0.005
0.005
0.005
1.0
1.0
1.0
1.0
1.0
0.039
0.039
0.039
0.039
0.039
0.127
0.195
0.290
0.376
0.426
0.28
0.43
0.64
0.83
0.94
7800
11300
15300
19800
20500
1760
2550
3450
4460
4600
16000
22200
29100
36200
36300
3600
5000
6550
8130
8160
210K
211K
212K
213K
214K
50
55
60
65
70
1.9685
2.1654
2.3622
2.5591
2.7559
0.012
0.015
0.015
0.015
0.015
0.00047
0.0006
0.0006
0.0006
0.0006
90
100
110
120
125
3.5433
3.9370
4.3307
4.7244
4.9213
0.015
0.015
0.015
0.015
0.018
0.0006
0.0006
0.0006
0.0006
0.0007
20
21
22
23
24
0.7874
0.8268
0.8661
0.9055
0.9449
0.12
0.15
0.15
0.15
0.15
0.005
0.006
0.006
0.006
0.006
1.0
1.5
1.5
1.5
1.5
0.039
0.059
0.059
0.059
0.059
0.476
0.635
0.807
1.016
1.107
1.05
1.40
1.78
2.24
2.44
23100
29100
35500
39900
44000
5200
6550
8000
9000
9890
40000
49000
62100
62100
69000
9000
11000
13400
14600
15500
215K
216K
217K
218K
75
80
85
90
2.9528
3.1496
3.3465
3.5433
0.015
0.015
0.020
0.020
0.0006
0.0006
0.0008
0.0008
130
140
150
160
5.1181
5.5118
5.9055
6.2992
0.018
0.018
0.018
0.025
0.0007
0.0007
0.0007
0.0010
25
26
28
30
0.9843
1.0236
1.1024
1.1811
0.15
0.15
0.20
0.20
0.006
0.006
0.008
0.008
1.5
2.0
2.0
2.0
0.059
0.079
0.079
0.079
1.198
1.483
1.860
2.209
2.64
3.27
4.10
4.87
44800
54200
62200
71100
10100
12200
14000
16000
68900
81300
95900
109000
15500
18300
21600
24500
220K
221K
222K
224K
226K
228K
100
105
110
120
130
140
3.9370
4.1339
4.3307
4.7244
5.1181
5.5118
0.020
0.020
0.020
0.020
0.020
0.025
0.0008
0.0008
0.0008
0.0008
0.0010
0.0010
180
190
200
215
230
250
7.0866
7.4803
7.8740
8.4646
9.0551
9.8425
0.025
0.030
0.030
0.030
0.030
0.030
0.0010
0.0012
0.0012
0.0012
0.0012
0.0012
34
36
38
40
40
42
1.3386
1.4173
1.4961
1.5748
1.5748
1.6535
0.20
0.20
0.20
0.20
0.25
0.25
0.008
0.008
0.008
0.008
0.010
0.010
2.0
2.0
2.0
2.0
3.0
3.0
0.080
0.080
0.080
0.080
0.120
0.120
4.077 8.98
3.777 8.32
4.300 9.47
7.064 15.56
6.642 14.63
11.196 24.66
93000
93000
104900
133000
149000
162000
20800
20800
23600
30000
33500
36500
134000
127000
153000
173000
189000
200000
30500
28500
34500
39000
42500
45000
230K
232K
234K
236K
238K
150
160
170
180
190
5.9055
6.2992
6.6929
7.0866
7.4803
0.025
0.025
0.025
0.025
0.030
0.0010
0.0010
0.0010
0.0010
0.0012
270
290
310
320
340
10.6299
11.4173
12.2047
12.5984
13.3858
0.035
0.035
0.035
0.040
0.040
0.0014
0.0014
0.0014
0.0016
0.0016
45
48
52
52
55
1.7717
1.8898
2.0472
2.0472
2.1654
0.25
0.25
0.25
0.25
0.30
0.010
0.010
0.010
0.010
0.012
3.0
3.0
4.0
4.0
4.0
0.120
0.120
0.160
0.160
0.160
12.17
15.03
18.66
19.39
23.02
180000
235000
276000
298000
290000
40500
53000
62000
67000
65000
218000
260000
291000
309000
300000
49000
58500
65500
69500
67000
240K
242K
244K
246K
248K
200
210
220
230
240
7.8740
8.2677
8.6614
9.0551
9.4488
0.030
0.030
0.030
0.030
0.030
0.0012
0.0012
0.0012
0.0012
0.0012
360
380
400
420
440
14.1732
14.9606
15.7480
16.5354
17.3228
0.040
0.040
0.040
0.045
0.045
0.0016
0.0016
0.0016
0.0018
0.0018
58
61
65
68
72
2.2835
2.4016
2.5591
2.6772
2.8346
0.30
0.30
0.30
0.30
0.30
0.012
0.012
0.012
0.012
0.012
4.0
4.0.
4.0
4.0
4.0
0.160
0.160
0.160
0.160
0.160
26.42 58.2
32.42 71.4
36.96 81.4
42.36 93.3
46.81 103.1
375000 83000
335000 76500
380000 86500
425000 95000
520000 116000
355000 80000
325000 73500
355000 80000
380000 85000
455000 102000
250K
252K
256K
260K
264K
250
260
280
300
320
9.8425
10.2362
11.0236
11.8110
12.5984
0.035
0.035
0.035
0.035
0.040
0.0014
0.0014
0.0014
0.0014
0.0016
460
480
500
540
580
18.1102
18.8976
19.6850
21.2598
22.8346
0.045
0.045
0.045
0.050
0.050
0.0018
0.0018
0.0018
0.0020
0.0020
76
80
80
85
92
2.9921
3.1496
3.1496
3.3465
3.6220
0.30
0.35
0.35
0.35
0.40
0.012
0.014
0.014
0.014
0.016
4.0
5.0
5.0
5.0
5.0
0.160
0.200
0.200
0.200
0.200
55.57
63.11
64.20
87.49
94.66
585000
640000
710000
670000
980000
490000
520000
560000
520000
710000
•
A
D14
in.
Extended
Dynamic
Load
Rating
CE (2)
26.8
33.1
41.1
42.7
50.7
122.4
139.0
141.4
192.7
208.5
129000
143000
160000
150000
220000
110000
118000
125000
116000
160000
Shields and Seals
OFFSET
Snap Ring (Wireloc) (1)
THICKNESS
O.D.
One
Shield
D
Two
Shields
DD
One
Seal
(N) P
One Seal
One Shield
PD
Two(3)
Seals
(N) PP
Open
Type
G
One
Shield
DG
One
Shield
GD
Two
Shields
DDG
One
Seal
PG
Two Seals
PPG
One Seal
One Shield
PDG
O.D.
Snap Ring
Thickness
Offset
mm
in.
mm
in.
mm
in.
200KD
201KD
202KD
203KD
204KD
200KDD
201KDD
202KDD
203KDD
204KDD
200P
201P
202P
203P
204P
200PD(2)
201PD
202PD
203PD
204PD
200PP
201PP
202PP
203PP
204PP
—
201KG
202KG
203KG
204KG
—
201KDG
202KDG
203KDG
204KDG
—
—
—
—
—
200KDDG
201KDDG
202KDDG
203KDDG
204KDDG
—
—
—
—
—
200PPG
201PPG
202PPG
203PPG
204PPG
—
—
—
—
—
34.5
36.5
39.3
44.4
52.4
1 23/64
1 7/16
1 35/64
13/4
2 1/16
1.07
1.07
1.07
1.07
1.07
0.042
0.042
0.042
0.042
0.042
3.05
3.05
3.05
3.05
3.45
0.120
0.120
0.120
0.120
0.136
205KD
206KD
207KD
208KD
209KD
205KDD
206KDD
207KDD
208KDD
209KDD
205P
206P
207P
208P
209P
205PD
206PD
207PD
—
—
205PP
206PP
207PP
208PP
209PP
205KG
206KG
207KG
208KG
209KG
205KDG
206KDG
207KDG
208KDG
209KDG
—
—
—
—
—
205KDDG
206KDDG
207KDDG
208KDDG
209KDDG
—
—
—
—
—
205PPG
206PPG
207PPG
208PPG
—
—
—
—
—
—
57.5
67.6
78.2
86.5
91.3
2 17/64
2 21/32
3 5/64
3 13/32
3 19/32
1.07
1.65
1.65
1.65
1.65
0.042
0.065
0.065
0.065
0.065
3.45
4.83
4.83
4.83
4.83
0.136
0.190
0.190
0.190
0.190
210KD
211KD
212KD
213KD
214KD
210KDD
211KDD
212KDD
213KDD
214KDD
210P
211NP
212NP
213NP
214P
—
211NPD
212NPD
—
—
210PP
211NPP
212NPP
213NPP
214NPP
210KG
211KG
212KG
213KG
214KG
210KDG
211KDG
212KDG
—
214KDG
—
211KGD
—
—
—
210KDDG
211KDDG
—
213KDDG
—
—
—
—
—
—
210NPPG
211NPPG
212NPPG
213NPPG
—
—
211NPDG
212NPDG
213NPDG
—
96.4
106.3
116.3
129.4
134.5
3 51/64
4 3/16
4 37/64
5 3/32
5 19/64
2.41
2.41
2.41
2.77
2.77
0.095
0.095
0.095
0.109
0.109
5.59
5.59
5.59
6.73
6.73
0.220
0.220
0.220
0.265
0.265
215KD
216KD
217KD
218KD
215KDD
216KDD
217KDD
218KDD
215P
—
—
—
—
—
—
—
215NPP
216NPP
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
222KD
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
DA
A
A
(1) The snap ring is normally packaged separately in the box with the bearing.
(2) Available with snap ring as 200PDG.
(3) Also available in "VV” sealed design. Check for availability.
Note: “N” prefix for NP(P) seals indicate non-removable seal.
A
A
D15
•
A
BALL BEARINGS
Light 200W Series
• 200W Series, maximum capacity type, is dimensionally interchangeable
•
•
with the 200K type, but has greater capacity for supporting heavier radial
loads and light thrust loads in either direction.
Maximum capacity bearings feature a filling slot in shoulder of each
raceway to assemble an extra-large complement of balls.
Consult your Timken representative for the availability of sizes other than
those listed here.
d
D
C
Fillet Wt.
Static
Load
Number
d Diameter
C
Radius(1)
tolerance
D tolerance
tolerance
Rating
+0.000 mm +0.000 mm
+0.000 mm
Co
+0.0000"
+0.0000"
+0.0000"
to minus
to minus
to minus
D
A
A
A
A
in.
in.
mm
in.
mm
mm
in.
mm
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs.
N
lbs.
202W
204W(2)
205W(2)
206W
207W
15
20
25
30
35
0.5906
0.7874
0.9843
1.1811
1.3780
0.008
0.010
0.010
0.010
0.012
0.0003
0.0004
0.0004
0.0004
0.00047
35
47
52
62
72
1.3780
1.8504
2.0472
2.4409
2.8346
0.011
0.011
0.013
0.013
0.013
0.00045
0.00045
0.0005
0.0005
0.0005
11
14
15
16
17
0.4331
0.5512
0.5906
0.6299
0.6693
0.12
0.12
0.12
0.12
0.12
0.005
0.005
0.005
0.005
0.005
0.6
1.0
1.0
1.0
1.0
0.024
0.039
0.039
0.039
0.039
0.054
0.113
0.141
0.213
0.313
0.12
0.25
0.31
0.47
0.69
5060
9300
12200
16900
22600
1140
2120
2750
3800
5100
11000
19500
22600
31000
40000
2450
4400
5100
6950
9000
208W
209W
210W
211W
212W
40
45
50
55
60
1.5748
1.7717
1.9685
2.1654
2.3622
0.012
0.012
0.012
0.015
0.015
0.00047
0.00047
0.00047
0.0006
0.0006
80
85
90
100
110
3.1496
3.3465
3.5433
3.9370
4.3307
0.013
0.015
0.015
0.015
0.015
0.0005
0.0006
0.0006
0.0006
0.0006
18
19
20
21
22
0.7087
0.7480
0.7874
0.8268
0.8661
0.12
0.12
0.12
0.15
0.15
0.005
0.005
0.005
0.006
0.006
1.0
1.0
1.0
1.5
1.5
0.039
0.039
0.039
0.059
0.059
0.413
0.463
0.522
0.681
0.885
0.91
1.02
1.15
1.50
1.95
28400
31500
34600
40600
54200
6400
7100
7800
9150
12200
47000
50000
52000
61000
78000
10600
11200
11800
13700
17600
213W
214W
215W
216W
217W
65
70
75
80
85
2.5591
2.7559
2.9528
3.1496
3.3465
0.015
0.015
0.015
0.015
0.020
0.0006
0.0006
0.0006
0.0006
0.0008
120
125
130
140
150
4.7244
4.9213
5.1181
5.5118
5.9055
0.015
0.018
0.018
0.018
0.018
0.0006
0.0007
0.0007
0.0007
0.0007
23
24
25
26
28
0.9055
0.9449
0.9843
1.0236
1.1024
0.15
0.15
0.15
0.15
0.20
0.006
0.006
0.006
0.006
0.008
1.5
1.5
1.5
2.0
2.0
0.059
0.059
0.059
0.079
0.079
1.207
1.225
1.334
1.633
2.019
2.66
2.70
2.94
3.60
4.45
64800
71100
75500
90600
96000
14600
16000
17000
20400
22400
92000
96000
99000
114000
129000
20800
21600
22400
26000
29000
218W
219W
220W
221W
222W
90
95
100
105
110
3.5433
3.7402
3.9370
4.1339
4.3307
0.020
0.020
0.020
0.020
0.020
0.0008
0.0008
0.0008
0.0008
0.0008
160
170
180
190
200
6.2992
6.6929
7.0866
7.4803
7.8740
0.025
0.025
0.025
0.030
0.030
0.0010
0.0010
0.0010
0.0012
0.0012
30
32
34
36
38
1.1811
1.2598
1.3386
1.4173
1.4961
0.20
0.20
0.20
0.20
0.20
0.008
0.008
0.008
0.008
0.008
2.0
2.0
2.0
2.0
2.0
0.079
0.079
0.080
0.080
0.080
2.493 5.49
3.039 6.70
3.673 8.09
4.277 9.43
5.144 11.34
96500
112000
127000
134000
160000
25500
29000
33500
35500
42500
149000
169000
188000
195000
222000
33500
38000
42500
44000
50000
224W3
226W3
228W3
120
130
140
4.7244
5.1181
5.5118
0.020 0.0008
0.020 0.0010
0.025 0.0010
215
230
250
8.4646
9.0551
9.8425
0.030 0.0012
0.030 0.0012
0.030 0.0012
40
40
42
1.5748
1.5748
1.6535
0.25 0.010
0.25 0.010
0.25 0.010
2.0
3.0
3.0
0.080
0.120
0.120
6.586 14.52
7.627 16.80
9.307 20.50
156000
196000
260000
41500
53000
58500
222000
260000
270000
50000
58500
61000
230W
232W
234W
236W
238W
150
160
170
180
190
5.9055
6.2992
6.6929
7.0866
7.4803
0.025
0.025
0.025
0.025
0.030
0.0010
0.0010
0.0010
0.0010
0.0012
270
290
310
320
340
10.6299
11.4173
12.2047
12.5984
13.3858
0.035
0.035
0.035
0.040
0.040
0.0014
0.0014
0.0014
0.0016
0.0016
45
48
52
52
55
1.7717
1.8898
2.0472
2.0472
2.1654
0.25
0.25
0.25
0.25
0.30
0.010
0.010
0.010
0.010
0.012
3.0
3.0
4.0
4.0
4.0
0.120
0.120
0.160
0.160
0.160
12.485
15.436
19.068
19.886
23.608
290000 65500
340000 76500
375000 85000
405000 90000
465000 104000
300000
325000
345000
365000
405000
67000
73500
78000
81500
91500
240W
242W
244W
246W
248W
200
210
220
230
240
7.8740
8.2677
8.6614
9.0551
9.4488
0.030
0.030
0.030
0.030
0.030
0.0012
0.0012
0.0012
0.0012
0.0012
360
380
400
420
440
14.1732
14.9606
15.7480
16.5354
17.3228
0.040
0.040
0.040
0.045
0.045
0.0016
0.0016
0.0016
0.0018
0.0018
58
61
65
68
72
2.2835
2.4016
2.5591
2.6772
2.8346
0.30
0.30
0.30
0.30
0.30
0.012
0.012
0.012
0.012
0.012
4.0
4.0
4.0
4.0
4.0
0.160
0.160
0.160
0.160
0.160
27.150 59.80
33.279 73.30
38.091 83.90
45.719 100.70
48.761 107.40
560000
570000
680000
695000
865000
125000
129000
153000
156000
193000
465000
465000
530000
530000
640000
106000
104000
120000
118000
143000
250W
252W
256W
260W
264W
250
260
280
300
320
9.8425
10.2362
11.0236
11.8110
12.5984
0.030
0.035
0.035
0.035
0.040
0.0012
0.0014
0.0014
0.0014
0.0016
460
480
500
540
580
18.1102
18.8976
19.6850
21.2598
22.8346
0.045
0.045
0.045
0.050
0.050
0.0018
0.0018
0.0018
0.0020
0.0020
76
80
80
85
92
2.9921
3.1496
3.1496
3.3465
3.6220
0.30
0.35
0.35
0.35
0.40
0.012
0.014
0.014
0.014
0.016
4.0
5.0
5.0
5.0
5.0
0.160
0.200
0.200
0.200
0.200
57.568 126.80
65.468 144.20
66.921 147.40
89.894 198.00
99.473 219.10
930000
1020000
1120000
1100000
1560000
208000
232000
255000
245000
355000
670000
720000
765000
720000
965000
150000
160000
170000
160000
216000
(2) These sizes have molded nylon cages.
•
A
Extended
Dynamic
Load
Rating*
CE (3)
D16
27.50
34.00
42.00
43.80
52.00
* For applications where thrust load exceeds 60% of radial load, consult your Timken representative.
Listed in the table below are Timken maximum capacity type bearings
(200W Series) with shields, seals and snap ring combinations.
The suffixes of the bearing numbers denote the following:
WD - Filling slot opposite single shield
WNPP - Two seals
WNP - Filling slot opposite single seal
WDG - Filling slot and snap ring opposite shield
WG - Filling slot opposite snap ring
WDDG - Two shields with filling slot opposite snap ring
WDD - Two shields
•
•
•
•
•
•
•
OFFSET
Shields and Seals
THICKNESS
O.D.
One
Shield
D
Two
Shields
DD
One
Seal
P
Two Seals
PP
Open
Type
G
One
Shield
DG
Two
Shields
DDG
O.D.
Thickness
Offset
mm
in.
mm
in.
mm
in.
204WD
205WD
206WD
207WD
—
—
—
—
—
—
—
—
—
—
—
—
204WG
205WG
206WG
207WG
—
—
206WDG
207WDG
—
—
—
—
52.4
57.5
67.5
78.2
2 1/16
2 17/64
2 21/32
3 5/64
1.07
1.07
1.65
1.65
0.042
0.042
0.065
0.065
3.45
3.45
4.83
4.83
0.136
0.136
0.190
0.190
208WD
209WD
210WD
211WD
212WD
208WDD
209WDD
210WDD
211WDD
212WDD
—
—
—
—
—
—
—
—
—
—
208WG
209WG
210WG
211WG(3)
212WG
208WDG
209WDG
210WDG(2)
211WDG
212WDG
208WDDG
—
—
—
212WDDG
86.5
91.3
96.4
106.4
116.3
3 13/32
3 19/32
3 51/64
4 3/16
4 37/64
1.65
1.65
2.41
2.41
2.41
0.065
0.065
0.095
0.095
0.095
4.83
4.83
5.59
5.59
5.59
0.190
0.190
0.220
0.220
0.220
213WD
214WD
215WD
216WD
217WD
213WDD
214WDD
215WDD
216WDD
217WDD
213WNP
—
215WNP
—
—
213WNPP
—
215WNPP
—
—
213WG
214WG
215WG
216WG
217WG
213WDG
214WDG
215WDG
216WDG
217WDG
213WDDG
—
215WDDG
—
—
129.4
134.5
139.7
149.6
159.5
5 3/32
5 19/64
5 1/2
5 57/64
6 9/32
2.77
2.77
2.77
2.77
2.77
0.109
0.109
0.109
0.109
0.109
6.73
6.73
6.73
7.54
7.54
0.265
0.265
0.265
0.297
0.297
218WD
219WD
220WD
221WD
222WD
218WDD
219WDD
220WDD
—
—
218WNP
—
—
—
—
—
—
—
—
—
218WG
—
220WG
—
—
—
—
—
—
—
—
—
—
—
—
169.5
—
192.9
—
—
6 43/64
—
7 19/32
—
—
2.77
—
3.05
—
—
0.109
—
0.12
—
—
7.54
—
8.61
—
—
0.297
—
0.339
—
—
224WD(4)
—
—
—
—
—
—
—
—
—
—
—
—
DA
A
A
(2) Also available as a GWD-type filling slot opposite the shield and snap ring.
(3) Also available as 211GW with filling slot on same side as snap ring.
(4) Width is 1.6535" for the 224WD bearing.
A
A
D17
•
A
BALL BEARINGS
Light 200 Series Extra Width Inner Ring
• Sizes available in rubber seal (P) and Mechani-Seal (L) design.
• Extra width inner ring provides greater shaft support.
• P seal version uses a Buna N rubber contact seal.
• L seal employs a frictionless metallic member to form a labyrinth.
• Used extensively in high-speed pneumatic tools, small pumps,
electric motors, domestic appliances, etc.
• Electric motor quality for applications where quietness is a
requirement.
Bearing Number
Bore
Outside Diameter
Width
Inner Ring Widths
Fillet
Wt.
Static
Extended
Ring 0.00, -.12 mm
Radius(1)
Load
Dynamic
d
D
B1
one seal tolerance tolerance
Offset+0.000”, - .005”
Rating
Load
Rating
one
and +0.000 mm +0.000 mm
Co
seal
shield +0.0000” +0.0000”
Inner
Outer
CE (1)
L
LD to minus to minus
B
C
D
A
mm
in.
mm
in.
mm
in.
mm
in.
mm in.
mm
in.
kg
lbs.
N
N
lbs.
200KL
201KL
—
201KL3
202KL4
200KLD
201KLD
201KLD2
—
202KLD4
10
12
13
11.07
14
0.3937
0.4724
0.5118
0.4358
0.5512
0.008
0.008
0.008
0.008
0.008
0.0003
0.0003
0.0003
0.0003
0.0003
30
32
32
32
35
1.1811
1.2598
1.2598
1.2598
1.3780
0.009 0.00035
0.011 0.00045
0.011 0.00045
0.011 0.00045
0.011 0.00045
mm
in.
12.70
12.70
12.70
12.70
12.70
0.500
0.500
0.500
0.500
0.500
0.51
0.51
0.51
0.51
0.51
0.020
0.020
0.020
0.020
0.020
12.19
12.19
12.19
12.19
12.19
0.480
0.480
0.480
0.480
0.480
mm in.
8.99
10.01
10.01
10.01
11.00
0.354
0.394
0.394
0.394
0.433
mm in.
0.6
0.6
0.6
0.6
0.6
0.024
0.024
0.024
0.024
0.024
0.036
0.041
0.041
0.041
0.045
0.08
0.09
0.09
0.09
0.10
2650
3000
3000
3000
3690
585
680
680
680
830
lbs.
6550
7500
7500
7500
8650
1530
1730
1730
1730
1930
202KL
202KL3
203KL
204KL
205KL
202KLD
202KLD3
203KLD
204KLD
205KLD
15
16
17
20
25
0.5906
0.6299
0.6693
0.7874
0.9843
0.008
0.008
0.008
0.010
0.010
0.0003
0.0003
0.0003
0.0004
0.0004
35
35
40
47
52
1.3780
1.3780
1.5748
1.8504
2.0472
0.011 0.00045
0.011 0.00045
0.011 0.00045
0.011 0.00045
0.013 0.0005
12.70
12.70
14.30
15.88
15.88
0.500
0.500
0.563
0.625
0.625
0.51
0.51
0.64
0.64
0.64
0.020
0.020
0.025
0.025
0.025
12.19
12.19
13.67
15.24
15.24
0.480
0.480
0.538
0.600
0.600
11.00
11.00
11.99
14.00
15.01
0.433
0.433
0.472
0.551
0.591
0.6
0.6
0.6
1.0
1.0
0.024
0.024
0.024
0.039
0.039
0.045
0.045
0.073
0.113
0.132
0.10
0.10
0.16
0.25
0.29
3450
3450
4700
6200
7800
830
830
1060
1460
1760
8650
8650
10800
14300
16000
1930
1930
2450
3200
3600
206KL
207KL
209KL
211KL
206KLD
207KLD
209KLD
211KLD
30 1.1811 0.010 0.0004
62
35 1.3780 0.012 0.00045 72
45 1.7717 0.012 0.00045 85
55 2.1654 0.015 0.0006 100
2.4409
2.8346
3.3465
3.9370
0.013 0.0005
0.013 0.0005
0.015 0.0006
0.015 0.0006
20.00
21.00
26.00
27.00
0.787
0.827
1.024
1.063
0.99
0.99
—
—
0.039
0.039
—
—
19.00
20.00
26.00
27.00
0.748
0.787
1.024
1.063
16.00
17.00
19.00
21.01
0.630
0.669
0.748
0.827
1.0
1.0
1.0
1.5
0.039
0.039
0.039
0.059
0.231
0.322
0.508
0.748
0.51
0.71
1.12
1.65
10000
13700
17600
29100
2550
3450
4550
6550
22200
29000
37000
49000
5000
6550
8300
11000
A
Bearing Number
Bore
Outside Diameter Ring Widths
Fillet
Wt.
Static
Load
d
D 0.00, -.12 mm
Radius(1)
tolerance
tolerance +0.000”, -.005"
Rating
two
two +0.000 mm +0.000 mm
Co
seals
seals +0.0000”
+0.0000”
Inner
Outer
LL
NPP to minus
to minus
B2
C
mm
in.
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs.
N
lbs.
200KLL2
201KLL2
201KLL3
200KRR3(4)
—
—
10
12
13
0.3937
0.4724
0.5118
0.008 0.0003
0.008 0.0003
0.008 0.0003
30
32
32
1.1811
1.2598
1.2598
0.009 0.00035
0.011 0.00045
0.011 0.00045
16.40 0.646
15.40 0.606
15.40 0.606
8.99
10.01
10.01
0.354
0.394
0.394
0.6
0.6
0.6
0.024
0.024
0.024
0.036
0.041
0.041
0.08
0.09
0.09
2650
3000
3000
585
680
680
6800
7500
7500
1530
1700
1700
202KLL2
202KLL3
203KLL2(2)
204KLL2
205KLL2(3)
—
202NPP11
203NPP8
204NPP7
205NPP2
15
16
17
20
25
0.5906
0.6299
0.6693
0.7874
0.9843
0.008
0.008
0.008
0.010
0.010
0.0003
0.0003
0.0003
0.0004
0.0004
35
35
40
47
52
1.3780
1.3780
1.5748
1.8504
2.0472
0.011
0.011
0.011
0.011
0.013
0.00045
0.00045
0.00045
0.00045
0.0005
14.40
14.40
16.60
17.75
16.75
0.567
0.567
0.654
0.699
0.659
11.00
11.00
11.99
14.00
15.01
0.433
0.433
0.472
0.551
0.591
0.6
0.6
0.6
1.0
1.0
0.024
0.024
0.024
0.039
0.039
0.045
0.045
0.073
0.113
0.132
0.10
0.10
0.16
0.25
0.29
3690
3690
4700
6200
7800
830
830
1060
1460
1760
8650
8650
10800
14300
16000
1930
1930
2450
3200
3600
206KLL
207KLL
208KLL
209KLL
206NPP2
—
—
—
30
35
40
45
1.1811
1.3780
1.5748
1.7717
0.010
0.012
0.012
0.012
0.0004
0.00045
0.00045
0.00045
62
72
80
85
2.4409
2.8346
3.1496
3.3465
0.013
0.013
0.013
0.015
0.0005
0.0005
0.0005
0.0006
24.00
25.00
30.18
30.00
0.945
0.984
1.188
1.181
16.00
17.00
18.01
19.00
0.630
0.669
0.709
0.748
1.0
1.0
1.0
1.0
0.039
0.039
0.039
0.039
0.231
0.322
0.463
0.508
0.51
0.71
1.02
1.12
11300
15300
20200
20200
2550
3450
4550
4550
22200
29000
36000
37000
5000
6550
8150
8300
A
A
mm
in.
mm
in.
mm
in.
Extended
Dynamic
Load
Rating
CE (5)
(2) Also available as 203KLL with 18.24 mm (.718”) inner ring width.
(3) Also available as 205KLL with 20.64 mm (.812”) inner ring width.
(4) Equipped with R-Seal.
•
A
D18
E
E
P
C
C
C
B
B
d
C
K
K
D
One Mechani-Seal L
d
B1
B2
B2
One Shield and
Mechani-Seal LD
Two Mechani-Seals LL
Two Rubber Seals
NPP(2)
B1
D
K
DA
MECHANI-SEAL SNAP RING COMBINATIONS
OFFSET
THICKNESS
A
O.D.
LG
LDG
(Seal Projection)
One
One
(L, LD, LL Types Only)
Mechani-Seal Mechani-Seal
and Shield
Width
O.D.
E
P
K
LG
LDG
mm
in.
mm
in.
mm
in.
12.22
12.19
12.19
0.481
0.480
0.480
15.57
14.40
14.40
0.613
0.567
0.567
25.4
27.0
27.0
1
1 1/16
1 1/16
—
—
—
—
—
201KLDG3
12.37
12.37
14.00
15.57
15.57
0.487
0.487
0.551
0.613
0.613
13.79
13.79
16.00
17.14
16.13
0.543
0.543
0.630
0.675
0.635
30.2
30.2
34.9
40.1
45.6
1 3/16
1 3/16
1 3/8
1 37/64
1 51/64
—
—
203KLG
204KLG2
205KLG2
19.48
20.50
23.32
24.23
0.767
0.807
0.918
0.954
22.99
23.98
28.63
29.46
0.905
0.944
1.127
1.160
54.4
62.7
69.8
75.4
2 9/64
2 15/32
2 3/4
2 31/32
—
—
—
—
LLG
Snap Ring(1)
Two
Mechani-Seals
LLG
O.D.
Thickness
Offset
mm
in.
mm
in.
mm
in.
200KLLG2
201KLLG2
—
34.5
36.5
36.5
1 23/64
1 7/16
1 7/16
1.07
1.07
1.07
0.042
0.042
0.042
3.05
3.05
3.05
0.120
0.120
0.120
202KLDG
—
—
—
—
202KLLG2
202KLLG3
203KLLG2
204KLLG2
205KLLG2
39.3
39.3
44.4
52.4
57.5
1 35/64
1 35/64
1 3/4
2 1/16
2 17/64
1.07
1.07
1.07
1.07
1.07
0.042
0.042
0.042
0.042
0.042
3.05
3.05
3.05
3.45
3.45
0.120
0.120
0.120
0.136
0.136
—
—
—
—
206KLLG
207KLLG
—
209KLLG
67.5
78.2
86.5
91.3
2 21/32
3 5/64
3 13/32
3 19/32
1.65
1.65
1.65
1.65
0.065
0.065
0.065
0.065
4.83
4.83
4.83
4.83
0.190
0.190
0.190
0.190
A
A
NOTE: “N” prefix indicates a non-removable seal.
A
D19
•
A
BALL BEARINGS
Light 200 Series Felt Seal Type
• Permits certain design economies, but cannot be
assumed to be suitable for all conditions of service.
• In many cases, they are supplemented by adjacent parts
•
•
B
d
in the application for adequate bearing protection in
small equipment such as fractional horsepower motors,
electric vacuum cleaners, small gear units, electric and
pneumatic tools, etc.
Suggested for effective grease retention and exclusion
of foreign matter.
Electric motor quality for applications where quietness is
a requirement.
D
B
d
d
D
D
C
C
C1
One Seal T
One Seal and Shield
TD
Two Seals
TT
Bearing Number Bore Outside Ring Widths
Inner
Fillet
Wt.
Static
Load
d Diameter
+0.00 mm, -0.12 mm
Ring
Radius(1)
tolerance
D tolerance
0.000, -0.005"
Offset
Rating
one one seal +0.000 mm +0.000 mm
Co
+0.0000"
seals and shield
+0.0000"
T
TD to minus
to minus
D
A
Extended
Dynamic
Load
Rating
CE (3)
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs.
N
lbs.
10
12
12
13
15
0.3937
0.4724
0.4724
0.5118
0.5906
0.008
0.008
0.008
0.008
0.008
0.0003
0.0003
0.0003
0.0003
0.0003
30
30
32
32
35
1.1811
1.1811
1.2598
1.2598
1.3780
0.009
0.009
0.011
0.011
0.011
0.00035
0.00035
0.00045
0.00045
0.00045
12.19
12.19
12.19
12.19
12.19
0.480
0.480
0.480
0.480
0.480
12.70
12.70
12.70
12.70
12.70
0.500
0.500
0.500
0.500
0.500
0.51
0.51
0.51
0.51
0.51
0.020
0.020
0.020
0.020
0.020
0.6
0.6
0.6
0.6
0.6
0.024
0.024
0.024
0.024
0.024
0.045
0.045
0.045
0.045
0.050
0.10
0.10
0.10
0.10
0.11
2600
2600
3000
3000
3600
585
585
680
680
830
6790
6790
7680
7680
8650
1530
1530
1730
1730
1930
202KT3(2) 202KTD3(2)
203KT 203KTD
204KT 204KTD
205KT 205KTD
206KT 206KTD
16
17
20
25
30
0.6299
0.6693
0.7874
0.9843
1.1811
0.008
0.008
0.010
0.010
0.010
0.0003
0.0003
0.0004
0.0004
0.0004
35
40
47
52
62
1.3780
1.5748
1.8504
2.0472
2.4409
0.011
0.011
0.011
0.013
0.013
0.00045
0.00045
0.00045
0.00050
0.00050
12.19
13.67
15.24
15.24
19.00
0.480
0.538
0.600
0.600
0.748
12.70
14.30
15.88
15.88
19.99
0.500
0.563
0.625
0.625
0.788
0.51
0.64
0.64
0.64
0.99
0.020
0.025
0.025
0.025
0.039
0.6
0.6
1.0
1.0
1.0
0.024
0.024
0.039
0.039
0.039
0.050
0.077
0.118
0.132
0.245
0.11
0.17
0.26
0.29
0.54
3600
4700
6500
7800
11300
830
1060
1460
1760
2550
8650
10900
14400
16000
22200
1930
2450
3250
3600
5000
207KT
35
1.3780
0.012 0.00045 72
2.8346
0.013 0.00050 19.99 0.787
0.99 0.039
1.0
0.039
0.358 0.79
200KT
—
201KT
201KT2
202KT
200KTD
200KTD2
201KTD
201KTD2
202KTD
207KTD
21.01 0.827
15300 3450
29000 6550
(2) 202KT3 has 12.29 mm (.484") inner ring width.
A
Bearing
Bore
Outside Number
d
Diameter
tolerance
D tolerance
two
+0.000 mm
+0.000 mm
seals
+0.0000"
+0.0000"
TT
to minus
to minus
mm
A
A
Ring Width
Fillet
Wt.
Static
Radius(1)
Load
C1
+0.00 mm
Rating
-0.12 mm
Co
+0.000
-0.005"
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
kg
N
lbs.
N
lbs.
200KTT
201KTT
201KTT3
202KTT
10
12
13
15
0.3937
0.4724
0.5118
0.5906
0.008
0.008
0.008
0.008
0.0003
0.0003
0.0003
0.0003
30
32
32
35
1.1811
1.2598
1.2598
1.3780
0.009
0.011
0.011
0.011
0.00035
0.00043
0.00043
0.00043
16.66
16.66
16.66
16.66
0.656
0.656
0.656
0.656
0.6
0.6
0.6
0.6
0.024
0.024
0.024
0.024
0.045
0.045
0.045
0.050
0.10
0.10
0.10
0.11
2600
3000
3000
3600
585
680
680
830
6790
7680
7680
8650
1530
1730
1730
1930
203KTT
204KTT
205KTT
206KTT
17
20
25
30
0.6693
0.7874
0.9843
1.1811
0.008
0.010
0.010
0.010
0.0003
0.0004
0.0004
0.0004
40
47
52
62
1.5748
1.8504
2.0472
2.4409
0.011
0.011
0.013
0.013
0.00043
0.00043
0.00051
0.00051
18.24
20.62
20.62
24.00
0.718
0.812
0.812
0.945
0.6
1.0
1.0
1.0
0.024
0.039
0.039
0.039
0.077
0.118
0.132
0.245
0.17
0.26
0.29
0.54
4700
6500
7800
11300
1060
1460
1760
2550
10900
14400
16000
22200
2450
3250
3600
5000
207KTT
35
1.3780
0.012 0.00045
72
2.8346
0.013
0.00051
25.00
0.984
1.0
0.039
0.358
0.79
15300
3450
29000
6550
•
A
D20
lbs.
Extended
Dynamic
Load
Rating
CE (2)
Light, Wide Type W200PP Series W200KLL Series
• Rubber seal (W200PP) and Mechani-Seal (W200KLL) types.
• Made with standard bores, standard outside diameters and
a single row of balls.
• Same widths as double-row bearings of corresponding size.
• Extra width offers a larger support area for shaft and housing
contact and added space for prepacked lubricant.
• Wide-type rubber seal bearings are particularly suited for use
•
•
d
d
D
in electric motors, where they simplify housing design by
eliminating auxiliary seals.
Wide-type Mechani-Seal ball bearings are designed for
applications where frictionless sealing and large grease
capacity are required.
Extremely effective grease retention and exclusion of foreign
matter are assured by close running clearance between the
seal members and slinger action of the outer member.
D
C
C
Rubber Seals
PP
Mechani-Seals
LL
OFFSET
THICKNESS
DA
O.D.
DIMENSIONS
– TOLERANCES
Bearing Bore
Outside
Width
Fillet
Wt.
Static
Extended
Snap Ring PPG(3)
Number
d
Diameter
C
Radius(1)
Load
Dynamic
D
Rating
Load
CE (4)
tolerance tolerance
+0.00 mm
C o
Contact Mechani- +0.000 mm +0.000 mm
-0.12 mm
Seal seal +0.0000" +0.0000"
+0.000"
PP
LL to minus to minus
-.005"
O.D.
thickness
offset
mm in.
mm in.
mm in.
mm in.
mm in.
mm in.
kg lbs.
N lbs.
N lbs. mm in. mm in.
mm in.
W200PP
W201PP
W202PP
W203PP(2)
W204PP
—
—
—
—
W204KLL
10
12
15
17
20
0.3937
0.4724
0.5906
0.6693
0.7874
0.008
0.008
0.008
0.008
0.010
0.0003
0.0003
0.0003
0.0003
0.0004
30
32
35
40
47
1.1811
1.2598
1.3780
1.5748
1.8504
0.009
0.011
0.011
0.011
0.011
0.00035
0.00045
0.00045
0.00045
0.00045
14.27
15.88
15.88
17.48
20.62
0.562
0.625
0.625
0.688
0.812
0.6
0.6
0.6
0.6
1.0
0.024
0.024
0.024
0.024
0.039
0.045
0.054
0.064
0.091
0.150
0.10
0.12
0.14
0.20
0.33
W205PP(2)
W206PP(2)
W207PP
W208PP
W209PP
W205KLL
W206KLL
W207KLL
W208KLL
W209KLL
25
30
35
40
45
0.9843
1.1811
1.3780
1.5748
1.7717
0.010
0.010
0.012
0.012
0.012
0.0004
0.0004
0.00045
0.00045
0.00045
52
62
72
80
85
2.0472
2.4409
2.8346
3.1496
3.3465
0.013
0.013
0.013
0.013
0.015
0.0005
0.0005
0.0005
0.0005
0.0006
20.62
23.83
26.97
30.18
30.18
0.812
0.938
1.062
1.188
1.188
1.0
1.0
1.0
1.0
1.0
0.039
0.039
0.039
0.039
0.039
0.177
0.295
0.458
0.630
0.668
0.39
0.65
1.01
1.39
1.47
W210PP
W214PP
—
—
50 1.9685
70 2.7559
0.012 0.00045
0.015 0.0006
90 3.5433
125 4.9213
0.015 0.0006
0.018 0.0007
30.18 1.188
39.67 1.562
1.0 0.039
1.5 0.059
0.767 1.69
1.810 3.99
2650 600
3000 695
3450 780
4400 1000
6200 1400
6950
10000
13700
17600
17600
1560
2280
3050
4000
4000
19600 4500
37500 8500
6550
7500
8650
10600
14300
1500
1700
1930
2360
3200
— —
— —
— —
44.4 1 3/4
— —
—
—
—
0.042
—
— —
— —
— —
4.7 0.185
— —
15600
21600
28500
36000
36000
3450
4800
6400
8150
8150
57.5 2 17/64 1.07 0.042
67.5 2 21/32 1.65 0.065
— —
— —
— —
— —
— —
— —
5.72 0.225
6.15 0.242
— —
— —
— —
—
—
—
—
39000 8800
69500 15600
—
—
—
—
—
1.07
—
—
—
—
—
—
—
A
A
A
(2) Also available with snap ring. To order, add suffix “G” to bearing number. Example: W205PPG.
A
D21
•
A
BALL BEARINGS
Medium 300K Series
• A heavier cross section than the 200 Series.
• Capable of carrying considerably heavier radial, thrust and
combined loads for a given bore size.
• Capable of withstanding heavy shock loads. A ball bearing of
heavier cross section is rarely required.
• Uses Conrad-type bearing that is well-balanced, with deep
races and uninterrupted race shoulders.
• Electric motor quality where quietness is a requirement.
d
D
C
Fillet Wt.
Static
Load
Number
d Diameter
C
Radius(1)
tolerance
D tolerance
tolerance
Rating
+0.000 mm +0.000 mm
+0.000 mm
Co
+0.0000"
+0.0000"
+0.0000"
to minus
to minus
to minus
D
A
A
A
A
mm
in.
mm
in.
mm
in.
mm
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs.
N
lbs.
300K
301K
302K
303K
304K
10
12
15
17
20
0.3937
0.4724
0.5906
0.6693
0.7874
0.008
0.008
0.008
0.008
0.010
0.0003
0.0003
0.0003
0.0003
0.0004
35
37
42
47
52
1.3780
1.4567
1.6535
1.8504
2.0472
0.011
0.011
0.011
0.011
0.013
0.00043
0.00043
0.00043
0.00043
0.0005
11
12
13
14
15
0.433
0.472
0.512
0.551
0.591
0.12
0.12
0.12
0.12
0.12
0.005
0.005
0.005
0.005
0.005
0.6
1.0
1.0
1.0
1.0
0.024
0.039
0.039
0.039
0.039
0.054
0.064
0.082
0.109
0.141
0.12
0.14
0.18
0.24
0.31
3460
3620
5240
6550
7800
780
815
1180
1460
1760
9200
9400
13300
15300
17900
2080
2120
3000
3450
4050
305K
306K
307K
308K
309K
25
30
35
40
45
0.9843
1.1811
1.3780
1.5748
1.7717
0.010
0.010
0.012
0.012
0.012
0.0004
0.0004
0.00047
0.00047
0.00047
62
72
80
90
100
2.4409
2.8346
3.1496
3.5433
3.9370
0.013
0.013
0.013
0.015
0.015
0.0005
0.0005
0.0005
0.0006
0.0006
17
19
21
23
25
0.669
0.748
0.827
0.906
0.984
0.12
0.12
0.12
0.12
0.12
0.005
0.005
0.005
0.005
0.005
1.0
1.0
1.5
1.5
1.5
0.039
0.039
0.059
0.059
0.059
0.236
0.354
0.472
0.644
0.862
0.52
0.78
1.04
1.42
1.90
12200
15600
18400
25900
31500
2750
3550
4150
5850
7100
26600
33900
37700
50600
59500
6000
7650
8500
11400
13400
310K
311K
312K
313K
314K
50
55
60
65
70
1.9685
2.1654
2.3622
2.5591
2.7559
0.012
0.015
0.015
0.015
0.015
0.00047
0.0006
0.0006
0.0006
0.0006
110
120
130
140
150
4.3307
4.7244
5.1181
5.5118
5.9055
0.015
0.015
0.018
0.018
0.025
0.0006
0.0006
0.0007
0.0007
0.0010
27
29
31
33
35
1.063
1.142
1.220
1.299
1.378
0.12
0.15
0.15
0.15
0.15
0.005
0.006
0.006
0.006
0.006
2.0
2.0
2.0
2.0
2.0
0.079
0.079
0.079
0.079
0.079
1.125
1.424
1.765
2.168
2.617
2.48
3.14
3.89
4.78
5.77
37700
44400
51500
59500
67900
8500
10000
11600
13400
15300
69300
81200
92300
104000
116000
15600
18300
20800
23600
26000
315K
316K
317K
318K
320K
75
80
85
90
100
2.9528
3.1496
3.3465
3.5433
3.9370
0.015
0.015
0.020
0.020
0.020
0.0006
0.0006
0.0008
0.0008
0.0008
160
170
180
190
215
6.2992
6.6929
7.0866
7.4803
8.4646
0.018
0.025
0.025
0.030
0.030
0.0007
0.0010
0.0010
0.0012
0.0012
37
39
41
43
47
1.457
1.535
1.614
1.693
1.850
0.15
0.15
0.20
0.20
0.20
0.006
0.006
0.008
0.008
0.008
2.0
2.0
2.5
2.5
2.5
0.079
0.079
0.098
0.098
0.098
3.175 7.00
3.756 8.28
5.008 11.04
5.121 11.29
7.085 15.62
76800
85700
95900
106000
139000
17300
19300
21600
24000
31500
128000
139000
151000
162000
195000
29000
31500
34000
36500
41500
321K
322K
326K
105
110
130
4.1339
4.3307
5.1181
0.020 0.0008
0.020 0.0008
0.020 0.0010
225 8.8583
240 9.4488
280 11.0236
0.030 0.0012
0.030 0.0012
0.035 0.0014
49
50
58
1.929
1.969
2.323
0.20 0.008
0.20 0.008
0.25 0.010
2.5
2.5
2.5
0.098
0.098
0.098
10.21
12.17
18.90
22.52
26.82
41.60
163000
166000
240000
36500
37500
54000
126000
220000
280000
48000
49000
63000
330K
332K
334K
336K
338K
150
160
170
180
190
5.9055
6.2992
6.6929
7.0866
7.4803
0.025
0.025
0.025
0.025
0.030
0.0010
0.0010
0.0010
0.0010
0.0012
320
340
360
380
400
12.5984
13.3858
14.1732
14.9606
15.7480
0.040
0.040
0.040
0.040
0.040
0.0016
0.0016
0.0016
0.0016
0.0016
65
68
72
75
78
2.559
2.677
2.835
2.953
3.071
0.25
0.25
0.25
0.25
0.30
0.010
0.010
0.010
0.010
0.012
2.5
2.5
2.5
2.5
4.0
0.098
0.098
0.098
0.098
0.16
27.10 59.70
31.51 69.40
36.82 81.10
42.04 92.60
47.6 105.0
310000
310000
355000
390000
440000
69500
69500
80000
88000
98000
335000
335000
360000
390000
425000
75000
75000
81500
88000
95000
340K
342K
344K
348K
200
210
220
240
7.8740
8.2677
8.6614
9.4488
0.030
0.030
0.030
0.030
0.0012
0.0012
0.0012
0.0012
420
440
460
500
16.5354
17.3228
18.1102
19.6850
0.045
0.045
0.045
0.045
0.0018
0.0018
0.0018
0.0018
80
84
88
95
3.150
3.307
3.465
3.740
0.30
0.30
0.30
0.30
0.012
0.012
0.012
0.012
4.0
4.0
4.0
4.0
0.16
0.16
0.16
0.16
56.1
58.1
69.8
81.1
123.6
128.2
154.0
178.9
465000
570000
610000
735000
104000
129000
137000
163000
425000 95000
510000 114000
520000 116000
600000 134000
352K
356K
260 10.2362
280 11.0236
0.050 0.0020
0.050 0.0020
102
108
4.016
4.252
0.35 0.014
0.35 0.014
4.0
4.0
0.16
0.16
98.4
142.8
217.0
315.0
850000 190000
780000 176000
670000 150000
585000 134000
0.035 0.0014
0.035 0.0014
540 21.2598
580 22.8346
•
A
D22
in.
Extended
Dynamic
Load
Rating
CE (2)
Shields and Seals
OFFSET
Snap Ring (Wireloc) (1)
THICKNESS
O.D.
One
Shield
D
Two
Shields
DD
One
Seal
P
One Seal
One Shield
PD
Two Seals
PP
Open
Type
G
One
Shield
PG
One
Shield
DG
Two
Shields
DDG
O.D.
Thickness
mm
in.
mm
in.
Offset
mm
in.
300KD
301KD
302KD
303KD
300KDD
301KDD
302KDD
303KDD
300P
—
—
303P
—
—
—
—
—
—
—
303PP
—
—
—
303KG
—
—
—
—
—
—
—
—
—
—
—
—
39.3
40.9
46.0
52.4
135/64
139/64
113/16
21/16
1.07
1.07
1.07
1.07
0.042
0.042
0.042
0.042
3.05
3.05
3.05
3.45
0.120
0.120
0.120
0.136
304KD
305KD
306KD
307KD
308KD
304KDD
305KDD
306KDD
307KDD
308KDD
304P
305P
306P
307P
308P
—
—
—
—
—
304PP
305PP
306PP
307PP
308PP
304KG
305KG
306KG
307KG
308KG
—
—
—
—
—
304KDG
305KDG
306KDG
307KDG
308KDG
304KDDG
305KDDG
306KDDG
307KDDG
308KDDG
57.5
67.5
78.2
86.5
96.4
2 17/64
2 21/32
3 5/64
3 13/32
3 51/64
1.07
1.65
1.65
1.65
2.41
0.042
0.065
0.065
0.065
0.095
3.45
4.83
4.83
4.83
5.59
0.136
0.190
0.190
0.190
0.220
309KD
310KD
311KD
312KD
313KD
314KD
309KDD
310KDD
311KDD
312KDD
313KDD
314KDD
309P
310P
311NP
—
—
—
—
—
311NPD
—
—
—
309PP
310PP
311NPP
312NPP
—
—
309KG
310KG
311KG
312KG
—
—
—
—
311NPG
—
—
—
309KDG
310KDG
—
—
—
—
309KDDG
310KDDG
311KDDG
312KDDG
313KDDG
—
106.4
116.3
129.4
139.7
149.6
—
4 3/16
4 37/64
5 3/32
5 1/2
5 57/64
——
2.41
2.41
2.77
2.77
2.77
—
0.095
5.59
0.095
5.59
0.109
6.73
0.109
6.73
0.109
7.54
— —
0.220
0.220
0.265
0.265
0.297
315KD
316KD
317KD
—
320KD
315KDD
316KDD
317KDD
—
320KDD
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
——
——
——
——
——
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
DA
A
A
Note: “N” prefix indicates a non-removable seal in NP (P) designs.
A
A
D23
•
A
BALL BEARINGS
Medium 300W Series
• A heavier cross section than the 200 Series.
• Capable of carrying considerably heavier radial, thrust and
combined loads for a given bore size.
• Capable of withstanding heavy shock loads. A ball bearing of
heavier cross section is rarely required.
• 300W Series bearings are dimensionally interchangeable with
d
D
the 300K Series. However, bearings within the 300W Series are
capable of carrying heavier radial loads, due to their larger ball
complements.
C
Fillet Wt.
Static
Load
Number
d Diameter
C
Radius(1)
tolerance
D tolerance
tolerance
Rating
+0.000 mm +0.000 mm
+0.000 mm
Co
+0.0000"
+0.0000"
+0.0000"
to minus
to minus
to minus
D
A
A
A
A
in.
mm
in.
mm
mm
in.
mm
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs.
N
lbs.
303W
304W
305W
306W
307W
17
20
25
30
35
0.6693
0.7874
0.9843
1.1811
1.3780
0.008
0.010
0.010
0.010
0.012
0.0003
0.0004
0.0004
0.0004
0.00047
47
52
62
72
80
1.8504
2.0472
2.4409
2.8346
3.1496
0.011
0.013
0.013
0.013
0.013
0.00045
0.0005
0.0005
0.0005
0.0005
14
15
17
19
21
0.551
0.591
0.669
0.748
0.827
0.12
0.12
0.12
0.12
0.12
0.005
0.005
0.005
0.005
0.005
1.0
1.0
1.0
1.0
1.5
0.039
0.039
0.039
0.039
0.059
0.118
0.154
0.259
0.386
0.513
0.26
0.34
0.57
0.85
1.13
9400
11300
17300
22600
29000
2120
2550
3900
5100
6550
20600
23900
33900
42800
51500
4650
5400
7650
9650
11600
308W
309W
310W
311W
312W
40
45
50
55
60
1.5748
1.7717
1.9685
2.1654
2.3622
0.012
0.012
0.012
0.015
0.015
0.00047
0.00047
0.00047
0.0006
0.0006
90
100
110
120
130
3.5433
3.9370
4.3307
4.7244
5.1181
0.015
0.015
0.015
0.015
0.018
0.0006
0.0006
0.0006
0.0006
0.0007
23
25
27
29
31
0.906
0.984
1.063
1.142
1.220
0.12
0.12
0.12
0.15
0.15
0.005
0.005
0.005
0.006
0.006
1.5
1.5
2.0
2.0
2.0
0.059
0.059
0.079
0.079
0.079
0.844
0.934
1.207
1.542
1.923
1.86
2.06
2.66
3.40
4.24
39000
47000
56000
66000
78000
8000
10600
12700
15000
17600
66000
78100
92000
106000
122000
15000
17600
20800
24000
27500
313W
314W
315W
316W
317W
65
70
75
80
85
2.5591
2.7559
2.9528
3.1496
3.3465
0.015
0.015
0.015
0.015
0.020
0.0006
0.0006
0.0006
0.0006
0.0008
140
150
160
170
180
5.5118
5.9055
6.2992
6.6929
7.0866
0.018
0.018
0.025
0.025
0.025
0.0007
0.0007
0.0010
0.0010
0.0010
33
35
37
39
41
1.299
1.378
1.457
1.535
1.614
0.15
0.15
0.15
0.15
0.20
0.006
0.006
0.006
0.006
0.008
2.0
2.0
2.0
2.0
2.5
0.079
0.079
0.079
0.079
0.098
2.413 5.32
2.885 6.36
3.497 7.71
4.154 9.15
4.872 10.74
96000
101000
127000
142000
157000
21600
22800
28500
32000
35500
144000
153000
180000
195000
211000
32500
34500
40500
44000
47500
318W
319W
320W
321W
322W
90
95
100
105
110
3.5433
3.7402
3.9370
4.1339
4.3307
0.020
0.020
0.020
0.020
0.020
0.0008
0.0008
0.0008
0.0008
0.0008
190
200
215
225
240
7.4803
7.8740
8.4646
8.8583
9.4488
0.030
0.030
0.030
0.030
0.030
0.0012
0.0012
0.0012
0.0012
0.0012
43
45
47
49
50
1.693
1.772
1.850
1.929
1.968
0.20
0.20
0.20
0.20
0.20
0.008
0.008
0.008
0.008
0.008
2.5
2.5
2.5
2.5
2.5
0.098
0.098
0.098
0.098
0.098
5.625
6.514
7.992
9.117
10.81
173000
191000
226000
244000
266000
39000
43000
51000
55000
60000
226000
239000
270000
284000
302000
51000
54000
61000
64000
68000
324W
326W
328W
330W
336W
120
130
140
150
180
4.7244
5.1181
5.5118
5.9055
7.0866
0.020
0.025
0.025
0.025
0.025
0.0008
0.0010
0.0010
0.0010
0.0010
260
280
300
320
380
10.2362
11.0236
11.8110
12.5984
14.9606
0.035
0.035
0.035
0.040
0.040
0.0014
0.0014
0.0014
0.0016
0.0016
55
58
62
65
79
2.165
2.323
2.441
2.559
3.110
0.20
0.25
0.25
0.25
0.25
0.008
0.010
0.010
0.010
0.010
2.5
2.5
2.5
2.5
2.5
0.098
0.098
0.098
0.098
0.098
15.01 33.10
19.56 43.12
23.06 50.80
26.81 59.10
47.66 105.10
338W
340W
342W
344W
348W
190
200
210
220
240
7.4803
7.8740
8.2677
8.6614
9.4488
0.030
0.030
0.030
0.030
0.030
0.0012
0.0012
0.0012
0.0012
0.0012
400
420
440
460
500
15.7480
16.5354
17.3228
18.1102
19.6850
0.040
0.045
0.045
0.045
0.045
0.0016
0.0018
0.0018
0.0018
0.0018
78
80
84
88
95
3.071
3.150
3.307
3.465
3.740
0.30
0.30
0.30
0.30
0.30
0.012
0.012
0.012
0.012
0.012
4.0
4.0
4.0
4.0
4.0
0.160
0.160
0.160
0.160
0.160
49.21
57.48
60.70
72.10
84.99
352W
356W
260 10.2362
280 11.0236
0.050 0.0020
0.050 0.0020
102
108
4.016
4.252
0.35 0.014
0.35 0.014
4.0
4.0
0.160
0.160
0.035 0.0014
0.035 0.0014
540 21.2598
580 22.8346
in.
Extended
Dynamic
Load
Rating
CE (2)
•
A
D24
12.39
14.36
17.62
20.10
23.84
108.40
126.60
133.70
158.80
187.20
103.38 227.70
146.78 323.30
284000 64000
326000 73500
410000 91500
422000 95000
600000 132000
720000
730000
935000
880000
1200000
160000
163000
208000
196000
260000
1400000 310000
1350000 300000
319000 72000
355000 80000
400000 90000
422000 95000
524000 118000
580000
570000
720000
700000
850000
129000
127000
160000
150000
186000
950000 208000
855000 190000
For applications where thrust load exceeds 60% Radial Load, consult your Timken representative.
Listed in the table below are Timken maximum capacity type bearings
(300W Series) with shields, seals and snap ring combinations.
The bearing number suffixes denote the following:
WD - filling slot opposite single shield
WG - filling slot opposite snap ring
WDD- two shields
WDG- filling slot and snap ring opposite shield
•
•
•
•
OFFSET
Shields and Seals
THICKNESS
O.D.
One
Shield
D
Two
Shields
DD
Open
Type
G
Open
Shield
DG
Two
Shields
DDG
O.D. Thickness
mm
in.
mm
Offset
in.
mm
in.
—
—
305WD
306WD
307WD
—
—
—
306WDD
307WDD
—
304WG
305WG
306WG
307WG
—
—
—
306WDG
307WDG
—
—
—
—
—
—
57.5
67.5
78.2
86.5
—
2 17/64
2 21/32
3 5/64
3 13/32
—
1.07
1.65
1.65
1.65
—
0.042
0.065
0.065
0.065
—
3.45
4.83
4.83
4.83
—
0.136
0.190
0.190
0.190
308WD
309WD
310WD
311WD
312WD
308WDD
309WDD
310WDD
311WDD
312WDD
308WG(2)
309WG
310WG
311WG
312WG(3)
308WDG
309WDG
310WDG
311WDG
312WDG
—
—
310WDDG
—
312WDDG
96.4
106.4
116.3
129.4
139.7
3 51/64
4 3/16
4 37/64
5 3/32
5 1/2
2.41
2.41
2.41
2.77
2.77
0.095
0.095
0.095
0.109
0.109
5.59
5.59
5.59
6.73
6.73
0.220
0.220
0.220
0.265
0.265
313WD
314WD
315WD
316WD
317WD
313WDD
314WDD
315WDD
316WDD
317WDD
313WG
—
—
316WG
—
313WDG
—
—
—
—
313WDDG
—
—
—
—
149.6
—
—
182.6
—
5 57/64
—
—
7 3/16
—
2.77
—
—
3.05
—
0.109
—
—
0.120
—
7.54
—
—
8.61
—
0.297
—
—
0.339
—
—
—
320WD
—
—
—
—
—
—
—
—
—
—
—
322WG
—
—
—
—
—
—
—
—
—
—
—
—
—
—
252.8
—
—
—
—
9 61/64
—
—
—
—
3.05
—
—
—
—
0.120
—
—
—
—
8.61
—
—
—
—
0.339
DA
A
A
(2) Also available as a GW-Type filling slot and snap ring on same side. Also available 308GW2 with 20 mm width.
(3) Also available as 312WG-3 with filling slot on same side as snap ring.
A
A
D25
•
A
BALL BEARINGS
Medium, Wide Type W300PP Series and W300KLL Series
• The W300PP (rubber seal) Series and the W300KLL
•
•
•
•
•
(Mechani-Seal) Series have the same bores and outside
diameters as standard 300 Series ball bearings.
Widths are equal to 5300 Series double-row ball bearings.
Added width provides extra support on shafts and in housings
and eliminates the need for locknuts and lockwashers on
applications such as electric motors.
Prepacked with the right amount of long-life, factoryfiltered grease.
These series incorporate the same advantages as the
standard width Mechani-Seal and rubber seal bearings.
Electric motor quality for applications where quietness
is a requirement.
d
d
D
D
C
C
Rubber Seals
PP
Mechani-Seals
LL
OFFSET
D
THICKNESS
O.D.
A
A
A
Bearing Bore
Outside
Width
Fillet
Wt.
Static
Extended
Snap Ring PPG
Load
Dynamic
Number
d
Diameter
C
Radius(1)
D
Rating
Load
CE (4)
tolerance tolerance
+0.00 mm
C o
ContactMechani- +0.000 mm +0.000 mm
-.12 mm
Seal Seal +0.0000" +0.0000"
+0.000"
PP LL to minus to minus
-.005"
O.D.
Thickness
Offset
mm in.
mm in.
mm in.
mm in.
mm in.
mm in.
kg lbs.
N lbs.
N lbs. mm in. mm in.
mm in.
W304PP
—
—
W305PP(2)
W306PP
—
W307KLL
W307PP
W308PP(2) W308KLL(2)
20
25
30
35
40
0.7874
0.9843
1.1811
1.3780
1.5748
0.010
0.010
0.010
0.012
0.012
0.0004
0.0004
0.0004
0.00047
0.00047
52
62
72
80
90
2.0472
2.4409
2.8346
3.1496
3.5433
0.013
0.013
0.013
0.013
0.015
0.0005
0.0005
0.0005
0.0005
0.0006
22.22
25.40
30.18
34.92
36.53
0.875
1.000
1.188
1.375
1.438
1.0
1.0
1.0
1.5
1.5
0.039
0.039
0.039
0.059
0.059
0.213
0.354
0.558
0.780
1.021
0.47
0.78
1.23
1.72
2.25
7800
12200
15600
18400
25900
W309PP
W309KLL
W310PP
—
W311PP(2) W311KLL
W312PP(2) W312KLL
W313PP
—
45
50
55
60
65
1.7717
1.9685
2.1654
2.3622
2.5591
0.012
0.012
0.015
0.015
0.015
0.00047
0.00047
0.0006
0.0006
0.0006
100
110
120
130
140
3.9370
4.3307
4.7244
5.1181
5.5118
0.015
0.015
0.015
0.018
0.018
0.0006
0.0006
0.0006
0.0007
0.0007
39.67
44.45
49.23
53.98
58.72
1.562
1.750
1.938(3)
2.125(3)
2.312(3)
1.5
2.0
2.0
2.0
2.0
0.059
0.079
0.079
0.079
0.079
1.370
1.828
2.386
3.053
3.883
3.02
4.03
5.26
6.73
8.56
W314PP
W315PP
70 2.7559
75 2.9528
4.731 10.43
5.811 12.81
—
—
0.015 0.0006
0.015 0.0006
150 5.9055
160 6.2992
0.018 0.0007
0.025 0.0010
63.50 2.500(3)
68.28 2.688(3)
(2) Also available with snap ring. To order, add suffix “G” to bearing number. Example: W305PPG.
The snap ring is normally packaged separately in the box with the bearing.
(.000" to -.006").
(3) Width tolerance is .00 mm to -.15 mm
A
•
A
D26
2.0 0.079
2.0 0.079
1760
2750
3550
4150
5850
17900 4050
26600 6000
33900 7650
37700 8500
50600 11400
— —
— —
67.5 2 21/35 1.65 0.065
— —
— —
— —
— —
96.4 3 51/64 2.41 0.095
— —
4.82 0.190
— —
— —
5.59 0.220
31500 7100 59000 13400
37700 8500 69000 15600
44400 10000 81000 18300
51500 11600 92000 20800
59500 13400 104000 23600
—
—
129.4
139.7
—
—
—
5 3/32
5 1/2
—
—
—
2.77
2.77
—
—
—
0.109
0.109
—
— —
— —
0.73 0.265
0.73 0.265
— —
67000 15300 116000 26000
76000 17300 128000 29000
—
—
—
—
—
—
—
—
—
—
—
—
C
Tri-Ply Seal Series Non-Relubricatable Type Cylindrical O.D.
• Designed for environments where severe contamination is
present, such as agricultural tillage equipment.
• One-piece Tri-Ply seals:
•
•
•
C
• Incorporate a highly effective design molded to an
exterior shroud cap.
d
D d protection against loss
D
• Provide exceptionally effective
of lubricant and entrance of wet or abrasive contaminants.
Seven-piece Tri-Ply construction:
d
• Standard on certain sizes.
• Shroud cap nests closely with the outside seal.
• Helps protect the rubber seal members from fiber wrap
warpage and abrasion.
• Balanced design, identified by deep races, large balls and
extra-wideBor heavy, shock-resistant inner and
B outer rings.
Use of Tri-Ply Seal bearings simplifies housing designs and
their extra inner ring width provides greater support on the shaft.
For speeds in excess of 500 RPM, consult your Timken representative.
Figure 1
Figure 2
d
D
D
B
B
Type 1
Type 2
DA
Figure 3
round bore
Bearing Type-Fig.
Bore
Outside Diameter Ring Widths Balls Wt.
Static
d
D 0.00, -.12 mm
Load
Number
tolerance tolerance +0.000", -0.005"
Rating
+0.000 mm +0.000 mm
Co
+0.0000” +0.0000”
B
C
to minus to minus
Inner
Outer
No. Size
W208PP10
W210PP8
W210PP2
W211PP2
W214PP2
W315PP2
1-1
2-
2-
2-2
2-
2-
mm
in.
mm
in.
mm
in.
mm
in.
38.113
38.860
49.230
55.580
70.000
76.342
1.5005
1.5300
1.9380
2.1880
2.7559
3.0056
0.013
0.250
0.013
0.015
0.015
0.015
0.0005
0.0100
0.0005
0.0006
0.0006
0.0006
80
90
90
100
125
160
3.1496
3.5433
3.5433
3.9370
4.9213
6.2992
0.013
0.015
0.015
0.015
0.020
0.025
0.0005
0.0006
0.0006
0.0006
0.0008
0.0010
(1) Inner and outer width tolerance is .00 mm to -.15 mm (.000" to .006").
mm
42.87
30.18
30.18
33.34(1)
39.69(1)
68.26(1)
in.
mm
in.
1.688
1.188
1.188
1.312
1.562
2.688
21.00
30.18
30.18
33.34
39.69
68.26
0.827
1.188
1.188
1.312
1.562
2.688
mm
9
10
10
10
10
8
in.
1/2
1/2
1/2
9/16
1 1/16
1 1/16
kg
lbs.
0.681 1.50
0.894 1.97
0.767 1.69
1.056 2.33
1.901 4.19
5.956 13.13
N
Extended
Dynamic
Load
Rating
CE (2)
lbs.
19900 4500
23000 5200
23000 5200
29000 6550
43500 9800
76800 17300
N
lbs.
36800 8300
39900 9000
39900 9000
48800 11000
71000 16000
128000 29000
Bearing Type-Fig.
Shaft Size
Outside Diameter Ring Widths Balls Wt.
Static
Number
d
D 0.00, -.12 mm
Load
tolerance +0.000", -0.005"
Rating
+0.000 mm
Co
+0.0000”
B
C
to minus
Inner
Outer
No. Size
1–1
1–1
1–1
2–2
1–2
mm
in.
25.4
28.6
28.6
38.1
38.1
1
1 1/8
1 1/8
1 1/2
1 1/2
mm
in.
mm
in.
80
80
80
100
101.6
3.1496
3.1496
3.1496
3.9370
4.0000
0.013
0.013
0.013
0.015
0.015
0.0005
0.0005
0.0005
0.0006
0.0006
mm
36.51
36.51
36.51
33.34(1)
44.45(1)
in.
mm
in.
1.438
1.438
1.438
1.312
1.750
18
18
30.18
33.34
36.52
0.709
0.709
1.188
1.312
1.438
mm 9
9
9
10
10
in.
kg
lbs.
N
lbs.
1/2
0.73
0.68
0.75
1.27
1.58
1.62
1.50
1.66
2.79
3.48
19900
19900
19900
29000
29000
4500
4500
4500
6550
6550
1/2
1/2
9/16
7/16
Extended
Dynamic
Load
Rating
CE (2)
N
lbs.
36800 8300
36800 8300
36800 8300
48800 11000
48800 11000
A
A
D27
•
W208PP6
W208PP5
W208PP8
W211PP3
W211PP5
A
A
square bore
A
BALL BEARINGS
C
Tri-Ply Seal Series Non-Relubricatable Type Spherical O.D.
• Similar in design and features to bearings shown on D27,
C
except for a spherical O.D.
d
d
D
d
D
D
d
D
B
Figure 1
D
Figure 2
Figure 3
B
B
B
Type 1
Type 2
round bore
Bearing Type-Fig.
Bore
Outside Diameter Ring Widths
Balls Stamping
Wt.
Static
Number
d
D +0.00, -.12 mm
Size
Load
tolerance tolerance +0.000", -0.005"
Rating
+0.000 mm +0.000 mm
Co
+0.0000” +0.0000”
B
C
to minus to minus
Inner
Outer
No. Size
A
A
A
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
W208PPB7
W208PPB2
W208PPB23
W209PPB2
W209PPB4
1–1
1–
1–1
2–2
2–2
30.170
38.113
38.113
45.000
39.000
1.1880
1.5005
1.5005
1.7717
1.5350
0.013
0.013
0.013
0.013
0.250
0.0005
0.0005
0.0005
0.0005
0.0100
80
80
80
85
85
3.150
3.150
3.150
3.346
3.346
0.013
0.013
0.013
0.015
0.015
0.0005
0.0005
0.0005
0.0006
0.0006
30.18
42.96
42.96
30.18
30.18
1.188
1.688
1.688
1.188
1.188
18.00
18.00
30.18
30.18
30.18
0.709
0.709
1.188
1.188
1.188
9
9
9
9
9
W210PPB2
W210PPB5
W211PPB2
W214PPB2
W214PPB9
2–
2–
2–2
2–
1–
49.230
45.340
55.580
70.000
70.260
1.9380
1.7850
2.1880
2.7559
2.7660
0.013
0.250
0.015
0.015
0.025
0.0005
0.0100
0.0006
0.0006
0.0010
90
90
100
125
125
3.543
3.543
3.937
4.921
4.921
0.015
0.015
0.015
0.02
0.02
0.0006
0.0006
0.0006
0.0008
0.0008
30.18
30.18
33.34(1)
39.69(1)
44.45(1)
1.188
1.188
1.312
1.562
1.750
30.18
30.18
33.34
39.69
28.00
1.188
1.188
1.312
1.562
1.102
10
10
10
10
10
(1) Inner and outer width tolerance is .00 mm to -.15 mm (.000" to -.006").
lbs.
N
lbs.
N
lbs.
0.640
0.721
0.681
0.653
0.748
1.41
1.59
1.50
1.44
1.65
19900
19900
15600
20200
20200
4500
4500
3550
4550
4550
36800
36800
32000
36800
36800
8300
8300
7200
8300
8300
1/2
0.708
0.794
0.966
1.796
1.796
1.56
1.75
3.63
3.96
3.96
23000
23000
29000
43500
43500
5200
5200
6550
9800
9800
39900 9000
39900 9000
48800 11000
71000 16000
71000 16000
80MS
1/2 80MS
15/32 80MS
1/2 85MS
1/2 85MS
90MS
90MS
9/16 100MS
11/16
— 0
11/16
— 0
1/2
Bearing Type-Fig.
Shaft Size
Outside Diameter Ring WidthsBallsStamping Wt.
Static
Number
D +0.00, -.12 mm Size
Load
tolerance +0.000", -0.005"
Rating
+0.000 mm
Co
+0.0000”
B
C
to minus to minus
Inner
Outer
No. Size
W208PPB13
W208PPB6
W208PPB5
W209PPB5
W210PPB4
W210PPB6
W211PPB3
1–1
1–1
1–1
1–2
2–
1–
2–2
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
22.2
25.4
28.6
31.8
28.6
7/8
80
80
80
85
90
3.1496
3.1496
3.1496
3.3465
3.5433
0.013
0.013
0.013
0.015
0.015
0.0005
0.0005
0.0005
0.0006
0.0006
36.53
36.53
36.53
36.53
30.18
1.438
1.438
1.438
1.438
1.188
18.00
18.00
18.00
30.18
30.18
0.709
0.709
0.709
1.188
1.188
9
9
9
9
10
1/2
1/2
80MS
80MS
80MS
85MS
90MS
90
100
3.5433
3.9370
0.015
0.015
0.0006
0.0006
36.53 1.438
33.34(1) 1.312
30.18
33.34
1.188
1.312
10
10
1/2
9/16
90MS
100MS
28.6
38.1
1
1 1/8
1 1/4
1 1/8
1 1/8
1 1/2
(1) Inner and outer width tolerance is .00 mm to -.15 mm (.000" to -.006").
•
A
kg
1/2
square bore
A
mm in.
Extended
Dynamic
Load
Rating
CE (2)
D28
mm in.
1/2
1/2
1/2
mm in.
Extended
Dynamic
Load
Rating
CE (2)
kg
lbs.
N
lbs.
1.62
1.59
1.47
1.75
2.11
19900
19900
19900
20200
23000
4500
4500
4500
4550
5200
36800
36800
36800
36800
39900
8300
8300
8300
8300
9000
1.021 2.25
1.207 2.66
23000
29000
5200
6550
39900 9000
48800 11000
0.735
0.721
0.667
0.794
0.957
Tri-Ply Seal Series Relubricatable Type
•
•
d
Similar
in design and features to those shown on
the preceding two pages.
Includes a provision for relubrication.
C
C
L
L
d
d
D
L
D
B
Figure 2
Figure 3
Type 1
B
B
B
Type 2
Type 3
B
Figure 1
D
L
B
Type 4
Round bore
Bearing Type-
BoreOutside Diameter Ring Width
Balls
L
Wt.
Number
Fig.
d
D
+0.00 mm, -0.12 mm
+0.000", -.005" tolerance tolerance
+0.000 mm +0.000 mm
+0.0000"
+0.0000"
B
C
to minus to minus
Inner
Outer
No. Size
ROUND BORE
mm
in.
mm in.
mm
in.
mm
in.
mm
in.
mm
in. in.
mm in.
kg lbs.
Static
Load
Rating
Co
Extended
Dynamic
Load
CE (3)
N
lbs.
N
lbs.
8.79
8.79
4.55
9.02
9.02
0.346
0.346
0.179
0.355
0.355
0.748
0.653
0.621
1.021
0.794
1.65
1.44
1.37
2.25
1.75
20200
20200
20200
23000
23000
4550
4550
4550
5200
5200
36800
36800
36800
39900
39900
8300
8300
8300
9000
9000
9.02
4.70
5.82
9.96
5.82
0.355
0.185
0.299
0.392
0.229
0.681
0.794
0.916
1.025
0.907
1.50
1.75
2.02
2.26
2.00
23000
23000
29000
29000
29000
5200
5200
6550
6550
6550
39900 9000
39900 9000
48800 11000
48800 11000
48800 11000
9.96
9.96
5.82
5.41
5.54
0.392
0.392
0.229
0.213
0.218
1.361
1.188
0.839
0.916
2.155
3.00
2.62
1.85
2.02
4.75
29000
29000
29000
29000
43500
6550
6550
6550
6550
9800
48800 11000
48800 11000
48800 11000
48800 11000
71000 16000
23/32
10.52
10.52
10.52
6.10
6.10
0.414
0.414
0.414
0.240
0.240
1.901 4.19
1.796 3.96
2.155 4.75
.— —
.— —
43500 9800
43500 9800
43500 9800
54000 12200
54000 12200
71000 16000
71000 16000
71000 16000
81000 18300
81000 18300
GW209PPB4
GW209PPB2
GW209PPB11
GW210PP3
GW210PPB5
4–2
4–2
2–2
3–
4–
39.00
45.00
45.24
37.53
45.34
1.5350
1.7717
1.7810
1.4065
1.7850
0.250
0.013
0.250
0.013
0.250
0.0100
0.0005
0.0100
0.0005
0.0100
85
85
85
90
90
3.3465
3.3465
3.3465
3.5433
3.5433
0.015
0.015
0.015
0.015
0.015
0.0006
0.0006
0.0006
0.0006
0.0006
30.18
30.18
36.53
30.18
30.18
1.188
1.188
1.438
1.188
1.188
30.18
30.18
22.00
30.18
30.18
1.188
1.188
0.866
1.188
1.188
9
9
9
10
10
1/2
GW210PPB2
GW210PP9(1)
GW211PPB13
GW211PPB10
GW211PPB14
4–
2–
2–2
4–2
2–2
49.23
49.40
45.34
49.23
51.18
1.9380
1.9450
1.7850
1.9380
2.0150
0.013
0.180
0.250
0.015
0.250
0.0005
0.0070
0.0100
0.0006
0.0100
90
90
100
100
100
3.5433
3.5433
3.9370
3.9370
3.9370
0.015
0.015
0.015
0.015
0.015
0.0006
0.0006
0.0006
0.0006
0.0006
30.18
36.53
33.34
33.34(2)
33.34(2)
1.188
1.438
1.312
1.312
1.312
30.18
23.00
25.00
33.34
25.00
1.188
0.906
0.984
1.312
0.984
10
10
10
10
10
1/2
GW211PP2
GW211PPB2
GW211PPB8
GW211PPB9
GW214PPB6
3–2
4–2
2–2
2–2
2–
55.58
55.58
55.58
55.75
68.28
2.1880
2.1880
2.1880
2.1950
2.6881
0.015
0.015
0.015
0.180
0.015
0.0006
0.0006
0.0006
0.0070
0.0006
100
100
100
100
125
3.9370
3.9370
3.9370
3.9370
4.9213
0.015
0.015
0.015
0.015
0.020
0.0006
0.0006
0.0006
0.0006
0.0008
33.34(2)
33.34(2)
33.34(2)
39.69(2)
68.26(2)
1.312
1.312
1.312
1.562
2.688
33.34
33.34
25.00
25.00
28.00
1.312
1.312
0.984
0.984
1.102
10
10
10
10
10
GW214PP2
GW214PPB2
GW214PPB5
GW216PPB3
GW216PP5
3–
4–
1–
2–3
3–3
70.00
70.00
70.00
76.45
63.88
2.7559
2.7559
2.7559
3.0100
2.5150
0.015
0.015
0.015
0.250
0.250
0.0006
0.0006
0.0006
0.0100
0.0100
125
125
125
140
140
4.9213
4.9213
4.9213
5.5118
5.5118
0.020
0.020
0.020
0.020
0.020
0.0008
0.0008
0.0008
0.0008
0.0008
39.69(2)
39.69(2)
61.90(2)
63.50(2)
63.50(2)
1.562
1.562
2.438
2.500
2.500
39.69
39.69
39.69
30.00
30.00
1.562
1.562
1.562
1.181
1.181
10
10
10
11
11
11/16
in.
1/2
1/2
1/2
1/2
1/2
9/16
9/16
9/16
9/16
9/16
9/16
9/16
11/16
11/16
11/16
23/32
SQUARE bore
DA
A
A
Shaft Size
SQUARE BORE mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs. N
lbs.
GW208PPB6
GW208PPB5
GW208PPB8
GW208PPB17
GW209PPB5
2–1
2–1
1–1
3–1
1–2
25.4
28.6
28.6
28.6
31.8
1
11/8
11/8
11/8
11/4
80
80
80
80
85
3.1496
3.1496
3.1496
3.3755
3.3456
0.013
0.013
0.013
0.013
0.015
0.0005
0.0005
0.0005
0.0005
0.0006
36.53
36.53
36.53
36.53
36.53
1.438
1.438
1.438
1.438
1.438
21.00
21.00
30.18
30.18
30.18
0.827
0.827
1.188
1.188
1.188
9
9
9
9
9
1/2
5.66
5.66
8.36
8.28
8.79
0.223
0.223
0.329
0.326
0.346
0.794
0.667
0.794
0.925
0.794
1.75
1.47
1.75
2.04
1.75
19900
19900
19900
19900
20200
4500
4500
4500
4500
4550
36800
36800
36800
36800
36800
8300
8300
8300
8300
8300
GW209PPB8
GW210PP4
GW210PPB4
GW211PP3
GW211PPB3
2–2
3–
4–
3–2
4–2
31.8
28.6
28.6
38.1
38.1
11/4
11/8
11/8
11/2
11/2
85
90
90
100
100
3.3456
3.5433
3.5433
3.9370
3.9370
0.015
0.015
0.015
0.015
0.015
0.0006
0.0006
0.0006
0.0006
0.0006
36.53
30.18
30.18
33.34(2)
33.34(2)
1.438
1.188
1.188
1.312
1.312
22.00
30.18
30.18
33.34
33.34
0.866
1.188
1.188
1.312
1.312
9
10
10
10
10
1/2
4.55
9.02
9.02
9.96
9.96
0.179
0.355
0.355
0.392
0.392
0.748
1.048
0.794
1.266
1.207
1.65
2.31
1.75
2.79
2.66
20200
23000
23000
29000
29000
4550
5200
5200
6550
6550
36800 8300
39900 9000
39900 9000
48800 11000
48800 11000
GW211PP17
GW214PPB4
GW216PPB4
GW216PP2(1)
GW226PPB2
3–2
4–
2–3
2–3
2–3
38.1
50.8
44.4
57.2
57.2
11/2
2
13/4
21/4
21/4
100
125
140
140
140
3.9370
4.9213
5.5118
5.5118
5.5118
0.015
0.020
0.020
0.020
0.020
0.0006
0.0008
0.0008
0.0008
0.0008
44.45(2)
39.69(2)
63.50(2)
63.50(2)
63.50(2)
1.750
1.562
2.500
2.500
2.500
33.34
39.69
30.00
30.00
30.00
1.312
1.562
1.181
1.181
1.181
10
10
11
11
11
9.96
10.52
6.10
6.10
6.10
0.392
0.414
0.240
0.240
0.240
1.188
2.155
—
—
—
2.62
4.75
—
—
—
29000 6550
43500 9800
54000 12200
54000 12200
54000 12200
48800 11000
71000 16000
81000 18300
81000 18300
81000 18300
1/2
1/2
1/2
1/2
1/2
1/2
9/16
9/16
9/16
11/16
23/32
23/32
23/32
A
A
(1) Cylindrical O.D.
(2) Inner and outer width tolerance is .00 mm to-.15 mm (.000" to -.006").
D29
•
A
BALL BEARINGS
Tri-Ply Series Disk Harrow Units
• The answer to versatility in design.
• For extra-special design needs, this unit incorporates a
•
•
D
Tri-Ply bearing mounted in two stampings, riveted together
with two o-rings.
Available in two basic size groups, one incorporating a 209 and
the other a 211 bearing.
Both size groups offer these features:
• Dynamic alignment capability (±3°).
• Shroud effect from close clearance of stamping to inner ring.
• Relubrication.
• One unit piece for ease of handling and assembly.
• Fitting flange mates with outer ring milled recess, preventing
possibility of outer ring circumferential movement.
• Stampings are case hardened to minimize wear.
• Units are equipped with nylon retainer, molded one-piece
seals and patented notched outer ring seal grooves.
H
A1
A
J
N1
N
L
G
H
A
A1
Static
Unit
Shaft
B
H2
Number
Diameter
Ref.
Load
Rating
Co
DHU 30S–209
DHU 40R–209
DHU 45R–209
DHU 40S–211
DHU 50R–211
DHU 55R–211
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
N
N
43
43
43
101.6
101.6
101.6
127.0
127.0
127.0
16.7
16.7
16.7
13.5
13.5
13.5
127.0
127.0
127.0
57.9
57.9
57.9
59.9
59.9
59.9
42.5
42.5
42.5
6.7
6.7
6.7
18000
18000
18000
36500
36500
36500
51
51
51
113.5
113.5
113.5
139.7
139.7
139.7
15.1
15.1
15.1
13.5
13.5
13.5
139.7
139.7
139.7
69.7
69.7
69.7
73.0
73.0
73.0
49.2
49.2
49.2
7.5
7.5
7.5
25000
25000
25000
48000
48000
48000
211 METRIC SERIES
40 SQ.
50 RD.
55 RD.
J
N1
N
L
G
H
A
A1
Static
Unit
Shaft
B
H2
Number
Diameter
Ref.
Load
Rating
Co
A
Extended
Dynamic
Load
Rating
CE (1)
in.
in.
in.
in.
in.
in.
in.
in.
in.
in.
in.
lbs.
lbs.
DHU 11⁄2 R–209
DHU 11⁄8 S–209
DHU 13⁄4 R–209
1 1⁄2 RD.
1 1⁄8 SQ.
1 3⁄4 RD.
1 11⁄16
1 11⁄16
1 11⁄16
4
4
4
5
5
5
21⁄32
17⁄32
17⁄32
21⁄32
17⁄32
2.279
2.279
2.279
2 23⁄64
2 23⁄64
2 23⁄64
1 43⁄64
1 43⁄64
1 43⁄64
17⁄64
21⁄32
5
5
5
4000
4000
4000
8150
8150
8150
DHU 11⁄4S–209
DHU 491 A
1 1⁄4 SQ.
1 3⁄4 RD.
1 3⁄4
1 3⁄4
4
4
5
5
21⁄32
17⁄32
17⁄32
2.279
2.279
2 23⁄64
2 23⁄64
1 43⁄64
1 43⁄64
17⁄64
21⁄32
5
5
4000
4000
8150
8150
DHU 11⁄2 S–211
DHU 13⁄4 R–211
DHU 23⁄16 R–211
1 1⁄2 SQ.
1 3⁄4 RD.
2 3⁄16 RD.
2
2 1⁄8
2 3⁄16
4
4
4
5 1⁄2
5 1⁄2
5 1⁄2
19⁄32
17⁄32
17⁄32
19⁄32
17⁄32
5 1⁄2
5 1⁄2
5 1⁄2
2.746
2.746
2.746
2 7⁄8
2 7⁄8
2 7⁄8
1 15⁄16
1 15⁄16
1 15⁄16
19⁄64
19⁄32
5600
5600
5600
10800
10800
10800
17⁄64
17⁄64
17⁄64
211 SERIES
A
Extended
Dynamic
Load
Rating
CE (1)
30 SQ.
40 SQ.
45 RD.
209
series
A
H2
MINIMUM
FRAME
OPENING
G
209
METRIC SERIES
A
B
•
A
D30
19⁄64
19⁄64
Hex Bore Bearings
• Designed to be used for outer or inner ring rotation in
•
• Main advantage is ease of mounting. Except for axial
low-speed, moderately-loaded applications, primarily in
agricultural implements and conveyors.
Tolerances of the hex bore are suitable for mounting on
cold rolled hex shafting.
F
G
G
G
C
C
C
d
•
positioning by adjacent parts, no collars, setscrews or other
locking devices are required to lock the inner ring to the
hex shaft.
Utilize the R-Type shroud seal.
G
A
C
d
D
B
B
Type 1
Type 2
B
Type 3
B
Type 4
Bearing
Type Hex
Hex Bore
Outside Diameter Width
F
G
Balls
Wt.
Static
Extended
Number
Shaft
Ad
D
Load
Dynamic
Size
tolerance tolerance +0.000 mm -0.12 mm
Rating
Load
-0.00 mm
Across +0.000 mm
+0.0000" -.005" CORating
+0.0000"
Across
+0.000"corners
C
B
CE (3)
Flats
to plus
min. to minus
Outer
Inner
No. Size
mm in. mm in. mmin. mmin. mmin. mmin. mmin. mmin. mmin.
DA
in. kglbs. N lbs. Nlbs.
Non-relubricatable type
9/16
202KRR31
11/16
204KRR21
7/8
205KRR21
7/8
205KRRB22
7/8
205PPB13(1)2
14.300.563 0.130.00516.46
0.648 351.37800.013
0.0005
17.650.695 0.130.00520.22 0.796 471.85040.013
0.0005
22.250.876 0.130.00525.65
1.010 522.04720.013
0.0005
22.250.876 0.130.00525.65 1.010 522.04720.013
0.0005
22.250.876 0.130.00525.65 1.010 522.04720.013
0.0005
110.43313.000.512 — — — — 87/32
140.55120.960.825 — — — — 85/16
150.59125.401.000 — — — — 95/16
150.59125.401.000 — — — — 95/16
150.59125.401.00042.67
1.68020.190.79595/16
0.054 0.12
0.145 0.32
0.200 0.44
0.200 0.44
0.200 0.44
4400 1000
6200 1400
6950 1560
6950 1560
6950 1560
106002360
143003200
156003450
156003450
156003450
206KPP3(1)
206KPPB3(1)
206KRR6
206KRRB6
207KPP3
1 1
2 1
1 1
2 1
11 1/4
25.431.001 0.130.00529.31 1.154 622.44090.013
0.0005
25.431.001 0.130.00529.31 1.154 622.44090.013
0.0005
25.431.001 0.130.00529.31 1.154 622.44090.013
0.0005
25.431.001 0.130.00529.31 1.154 622.44090.013
0.0005
31.771.251 0.130.00536.40 1.433 722.83460.013
0.0005
160.63024.000.94552.07
2.05019.560.7709 3/8
180.70924.000.94552.07
2.05019.560.7709 3/8
160.63024.000.94552.07
2.05019.560.7709 3/8
180.70924.000.94552.07
2.05019.560.7709 3/8
170.66937.701.48460.35
2.37619.680.77597/16
0.345 0.76
0.345 0.76
0.341 0.75
0.341 0.75
0.454 1.00
10000 2280
10000 2280
10000 2280
10000 2280
13700 3050
216004800
216004800
216004800
216004800
285006400
207KPPB3
207KRRB9
207KRRB12
207KRR17
207KRRB17
W208PPB16(1)
21 1/4
21 1/8
21 1/8
11 1/4
21 1/4
21 1/4
31.771.251 0.130.00536.40 1.433 722.83460.013
0.0005
28.601.126 0.130.00532.97 1.298 722.83460.013
0.0005
28.601.126 0.130.00532.97 1.298 722.83460.013
0.0005
31.771.251 0.130.00536.65 1.443 722.83460.013
0.0005
31.771.251 0.130.00536.65 1.443 722.83460.013
0.0005
31.771.251 0.130.00536.65 1.443 803.14960.013
0.0005
170.66925.000.98460.35
2.37619.680.77597/16
170.66937.701.48460.35
2.37619.680.77597/16
170.66925.000.98460.35
2.37619.680.77597/16
170.66925.000.98460.35
2.37619.680.77597/16
170.66925.000.98460.35
2.37619.680.77597/16
180.70936.531.43868.43
2.69425.270.9959 1/2
0.395 0.87
0.454 1.00
0.395 0.87
0.395 0.87
0.395 0.87
0.658 1.45
13700 3050
13700 3050
13700 3050
13700 3050
13700 3050
17600 4000
285006400
285006400
285006400
285006400
285006400
360008150
W208KRRB6
W208KRR8
209KRRB2
W210PPB7(1)
21 3/8
11 1/4
21 1/2
21 5/8
34.951.376 0.130.00540.30 1.587 803.14960.013
0.0005 210.82736.531.43868.43
2.69423.540.9279 1/2 .— — 17600 4000
31.771.251 0.130.00536.65 1.443 803.14960.013
0.0005 180.70936.531.43868.43
2.69420.450.8059 1/2 0.658 1.45 17600 4000
38.121.501 0.130.00543.99 1.732 853.34560.015
0.0006 190.74830.001.18173.86
2.90823.270.9169 1/2 0.576 1.27 17600 4000
41.301.626 0.130.00547.65 1.876 903.54330.015
0.000630.18
1.18830.181.188 — — — — 101/2 0.794 1.75 19600 4500
360008150
360008150
360008150
390008800
A
A
A
relubricatable type
G206KPP4(1)
G206KPPB4(1)
G206KRRB6
G207KPPB2(1)
GW208KRRB5
3 1
4 1
4 1
41 1/8
41 1/4
25.431.001 0.130.00529.26 1.152 622.44090.130.005
25.431.001 0.130.00529.26 1.152 622.44090.130.005
25.431.001 0.130.00529.26 1.152 622.44090.130.005
28.601.126 0.130.00532.97 1.298 722.83460.130.005
31.771.251 0.130.00536.65 1.443 803.14960.130.005
180.70924.000.945 — — — — 9 3/8
180.70924.000.94552.07
2.05019.560.7709 3/8
180.70924.000.94552.07
2.05019.560.7709 3/8
190.74837.701.48460.32
2.37525.401.00097/16
210.82736.511.43860.35
2.69422.430.8839 1/2
0.281 0.62
0.277 0.61
0.268 0.59
0.454 1.00
0.635 1.40
10000 2280
10000 2280
10000 2280
13700 3050
17600 4000
216004800
216004800
216004800
285006400
360008150
GW208PPB22(1)2 1 1/4 31.881.255 0.130.00536.75 1.447 803.14960.130.005 210.82736.511.43852.07
2.05028.321.1159 1/2 0.681 1.50 17600 4000 360008150
2.0201003.93700.015
0.0006 25(2)0.984 57.15 2.250 86.113.390 29.01 1.142 10 9/16 1.521 3.35 19600 4500 390008800
GC1200KPPB2(1) 1 3/4 44.481.751 0.130.00551.31 A
(1) Tri-Ply Seal bearing.
(2) Inner and outer ring tolerance is .00 mm to -15 mm (.000" to -.006").
D31
•
A
BALL BEARINGS
P
Light 200 Series R-Seal Type
C
• Consists of deep groove, Conrad-type bearings.
• Incorporates a flare-out, contact R-Seal.
• Synthetic rubber impregnated washer is enclosed
•
between two metal shields, providing excellent
protection against contaminants.
Because of the heavy contact seal, this series is
normally employed in moderate-speed service.
D
d
F
E
E
C
C
F
K
F
K
B
B
B
Type 1
Type 2
Type 3
D
BearingType
Bore
Outside Diameter
Width
E
P
K
Fillet
F
Static
Load
Number
d
D+0.00 -0.12 mm
Radius(1)
tolerance tolerance +0.000 -.005"
Rating
+0.000 mm +0.000 mm
CO
+0.0000" +0.0000"
B
C
to minus to minus
Inner Outer
Max.
Max.
Max.
A
A
mm
in.
mm
in.
15.883
16.256
13.081
17
19.063
0.6253
0.6400
0.5150
0.6693
0.7505
0.008
0.130
0.130
0.008
0.013
0.0003
0.0005
0.0005
0.0003
0.0005
mm
203KR2
203KRR2
203KRR5
203KRR7
204KR2
3
1
1
1
3
204KRR3
205KR4
206KR7
206KRR8
207KRR
1
20 0.7874 0.010 0.0004
2 25.413 1.0005 0.013 0.0005
2
30 1.1811 0.010 0.0004
1
30 1.1811 0.013 0.0004
1
35 1.3780 0.013 0.0005
47
52
62
62
72
208KRR2
209KRR3
210KRR
212KRR
1
1
1
1
80
85
90
110
40
45
50
60
1.5748
1.7717
1.9685
2.3622
0.013
0.013
0.013
0.015
0.0005
0.0005
0.0005
0.0006
in.
Extended
Dynamic
Load
Rating
CE (3)
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm. in.
mm. in.
N
lbs.
N
0.013
0.013
0.013
0.013
0.013
0.0005
0.0005
0.0005
0.0005
0.0005
14.00
18.29
18.29
16.61
15.49
0.551
0.720
0.720
0.654
0.610
12
12
12
12
15.49
0.472
0.472
0.472
0.472
0.610
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
0.6
0.6
0.6
0.6
1
0.024
0.024
0.024
0.024
0.039
24.44 0.962
24.44 0.962
24.44 0.962
24.44 0.962
28.73 1.131
4700
4700
4700
4700
6500
1060
1060
1060
1060
1460
10900
10900
10900
10900
14400
2450
2450
2450
2450
3250
1.8504
2.0472
2.4409
2.4409
2.8346
0.013
0.013
0.013
0.013
0.013
0.0005
0.0005
0.0005
0.0005
0.0005
17.75
25.40
24.00
24.00
25.00
0.699
1.000
0.945
0.945
0.984
14
15
16
16
17
0.551
0.591
0.630
0.630
0.669
—
15.875
17.780
—
—
—
0.625
0.700
—
—
—
—
—
—
—
—
19.56 0.77
19.68 0.775
—
42.67
52.07
52.07
60.35
—
1.68
2.05
2.05
2.376
1
1
1
1
1
0.039
0.039
0.039
0.039
0.039
28.73 1.131
33.81 1.331
40.28 1.586
39.09 1.539
46.94 1.848
6500
7800
11300
11300
15000
1460
1760
2550
2250
3450
14400
16000
21800
21800
29000
3250
3600
4900
4900
6550
3.1496
3.3465
3.5433
4.3307
0.013
0.013
0.015
0.015
0.0005
0.0005
0.0006
0.0006
27.00 1.063
27.00 1.063
30.00 1.181
36.00(2) 1.417
21
21
20
22
0.827
0.827
0.787
0.886
—
—
—
—
—
—
—
—
21.31
24.18
24.03
30.02
68.45
72.42
77.60
99.87
2.695
2.851
3.055
3.932
1
1
1
1
0.039
0.039
0.039
0.039
52.25 2.057
57.89 2.279
62.81 2.473
76.45 3.010
19800
20500
23100
35500
4460
4600
5200
8000
36200 8130
36300 8160
40000 9000
5860013200
40 1.5748
40 1.5748
40 1.5748
40 1.5748
45.225 1.7805
0.839
0.952
0.946
1.182
lbs.
(1) Maximum shaft or housing fillet radius which bearing corners will clear.
A
Farm Radial Specials
Bearing Number
202NPP9
A
Special Features
• 1⁄2 in. Bore
• O.D. corner turned to a 3⁄4 in. radius
• Special heavy stiff seals of
Buna-N rubber
• Crimped-in seal
Typical Applications
Cam Follower
1.5000"
1.4995"
38.100
38.087
3/
4
R
19
.015"
.005"
.4
.1
.505"
.500"
12.8
12.7
.5669"
.5619"
14.399
14.272
Special Features
• 1⁄12 in. Bore
• 1 ⁄2 in. O.D.
• Thick outer ring
1.5000"
1.4995"
38.100
38.087
3 /4
R
19
Cam Follower
.505"
.500"
12.8
12.7
.015"
.005"
.4
.1
•
A
Bearing Number
202KRR7
.4331"
.4281"
11.000
10.874
D32
K
Bearing Number
203KRR3
(continued)
.5906"
.5856"
15.000
14.874
Special Features
•
• 2 in. O.D.
2.0000"
1.9995"
50.800
50.787
5⁄8 in. Bore
1"R
25.4
Cam Follower
Guide Rolls for Baler Plunger
Special Features
• 3⁄4 in. Bore
• 1.7805 in. O.D.
• Replaces 204KRNP2
1.7805"
1.7800"
45.225
45.212
.6280"
.6277"
15.951
15.944
Mower Spindle
.7505"
.7500"
19.063
19.050
.015"
.005"
.4
.1
Bearing Number
203KRR6
.720"
.715"
18.288
18.161
Bearing Number
204RR7
Special Features
.4724"
.4674"
12.000
11.872
Special Features
• 5 ⁄8 in. Bore
• 47 mm O.D.
.610"
.605"
15.490
15.370
Bearing Number
P204RR6
1.8504"
1.8499"
47.000
46.987
Idler Pulley
Idler Sprocket
.610"
.605"
15.490
15.370
• 3⁄4 in. Bore
• 1.7805 in. O.D.
• Replaces 204KRNP3
DA
1.7805"
1.7800"
45.225
45.212
Rolling Cultivator
Disk
.640"
.635"
16.26
16.13
Bearing Number
203NPP9
Special Features
Bearing Number
205KR3
.510"
.500"
12.954
12.700
1.5748"
1.5743"
40.000
39.987
Disk Grain Drill
.6260"
.6255"
15.900
15.888
Special Features
• 5 ⁄8 in. Bore
• Gothic Arch Race
.700"
.695"
17.78
17.65
Special Features
• 5 ⁄8 in. Bore
• Width .500"
Bearing Number
204RY2
A
.755"
.750"
19.18
19.05
• 3⁄4 in. Bore
• Excellent moment load capacity
•
available from special internal
geometry of races
Heavy contact flare-out type
R-Seal with shroud cap
2.0472"
2.0467"
52.000
51.986
.640"
.635"
16.26
16.13
.700"
.695"
17.78
17.65
Bearing Number
205KP6
.610"
.605"
15.49
15.37
Special Features
• 3 ⁄4 in. Bore
• Tri-Ply Seal on one side
1.7805"
1.7800"
45.220
45.210
Planter
Double Disk Opener
.281"
7.14
REF.
A
2.0472"
2.0467"
52.000
51.986
with shroud cap
Rolling Cultivator
.631"
.626"
16.030
15.900
A
A
Disk Hiller, Planter
.735"
.730"
18.67
18.54
.751"
.750"
19.08
19.05
.921"
.916"
23.390
23.270
A
.756"
.751"
19.200
19.080
D33
•
BALL BEARINGS
Bearing Number
205KRR6
(continued)
.8661"
.8611"
22.000
21.872
1.375"
1.370"
34.920
34.800
Bearing Number
208NPPB5
.5906"
.5856"
15.000
14.874
Special Features
Special Features
• 1⁄2 in. Bore
• Extended inner ring
2.0472"
2.0467"
52.000
51.986
D
Special Features
1.4380"
1.4375"
36.525
36.512
.9449"
.9399"
24.000
23.873
.6299"
.6249"
16.000
15.872
2.4409"
2.4404"
62.000
61.986
Combine
1.1811"
1.1807"
30.000
29.990
Special Features
.9843"
.9793"
25.000
24.874
2.8346"
2.8341"
72.000
71.986
Disk Harrow
Transport Wheel
A
1.2530"
1.2525"
31.826
31.814
.9843"
.9793"
25.000
24.874
.6693"
.6643"
17.000
16.873
•
1.185"
1.175"
30.10
29.84
SQUARE
1.750"
1.745"
44.45
44.32
1.438"
1.433"
36.53
36.40
• 11⁄2 in. Square Bore
• Tri-Ply seal with shroud cap
• Heavy outer ring
4.077"
4.076"
103.560
103.530
4.130"
4.120"
104.90
104.65
Disk Harrow
1.536"
1.526"
39.010
38.760
SQUARE
2.016"
51.21
.7480"
.7430"
19.000
18.872
.672"
17.07
• Oil Seal on one side
• Molded double lip seal
D34
3.443"
3.433"
87.450
87.200
Disk Harrow
Special Features
2.8346"
2.8341"
72.000
71.986
A
Bearing Number
G1104KRXB2
Special Features
Disk Harrow
Transport Wheel
3.3760"
3.3750"
85.750
85.725
Special Features
• 11⁄4 in. Bore
Bearing Number
207KYY
• 11⁄8 in. Square Bore
• Molded Tri-Ply seal
• Heavy outer ring
Bearing Number
W211PPB6
.6693"
.6643"
17.000
16.873
A
1.1880"
1.1830"
30.175
30.048
Special Features
with shroud cap
A
1.4375"
1.4325"
36.512
36.386
Bearing Number
208PPB12
A
.515"
.510"
13.080
12.950
• Tri-Ply Seal on one side
Bearing Number
207KRR14
3.1496"
3.1491"
80.000
79.987
SPHERICAL
DIA.
Baler Crank Pin
Potato Harvester
Bearing Number
206KP2
• 1 7⁄16 in. Bore
• PP Seals with shroud cap
1.3780"
1.3775"
35.000
34.988
Chain Case
1.484"
37.690
1.2505"
1.2500"
31.763
31.750
2.8346"
2.8341"
72.000
71.986
SPHERICAL
2.109"
DIA.
53.59
Special Bearings
Size
Special Features
Typical
Application
Size
Special Features
Typical
Application
200KRR3
Inner Ring Width .6457/.6407
One piece molded seals
Windrower
205PP12
5⁄8" Bore Inner Width 1.500/1.495
Tri-Ply Seals
Cone Roller, Beet and
Potato Harvester
J202KRR8
Extended Inner Width .880/.875
Tobacco Harvester
205PP13
Corn Head Mechanism
202NPP9
1⁄2" Bore-O.D. corner turned to
3⁄4" radius
Baler Cam Foller
7⁄8" Hex Bore Inner Width
1.000/.995 Tri-Ply Seals
206KRD
Combine
P202NPP11
Extra Wide Inner .5669/.5619 Bore
16mm .6299/.6296
Cam Follower
Offset Rings
Inner Width .748/.743
Outer Width .6299/.6249
R-Seal on extended inner side
P203KRR3
5⁄8" Bore 2" O.D. Heavy section
outer ring
Cam Follower Guide
Rolls for Baler Plunger
206KP2
Tri-Ply Seal one side Wide Inner
Ring .9449/.9399
Combine
203KRR6
5⁄8" Bore 47mm O.D.Heavy
section outer ring
Baler Pick-up
206KPP2
Tri-Ply Seals Wide Inner Ring
.9449/.9399
Forrage Harvester
203NPP9
5⁄8" Bore .500" width
Disk Grain Drill Opener
3⁄4" Bore Wide Inner Ring .9449/
Disk Hiller and Bedders
P203PP10
.6255/.6260" Bore
Light Duty Disk Applications
H206KRP2
A1391
BB203KRR2
A2139
Wide Inner .720/.715 Bore
.6400/.6350 Gothic arch races
Rotary Hoe
206KPPB3
1" Hex Bore Tri-Ply Seals Inner
Ring Width .9449/.9399
Disk Harrow
P204KR2
Bore .7505/.7500 Width .610/.605
O.D. 1.7805/1.7800
Rotary Lawn Tractor
Blade Spindle Bearing
206KRR4
Large Inner Ring Bore Corner
to clear .090 R Shaft Fillet
Drive Shaft Bearing
204KRD4
5⁄8" Bore extended inner R-Seal
Disk Opener Seed
Drill
206KRRB3
11⁄8 Bore Flare out type R-Seal
with Shroud Cap
Corn Picker Snapping
Rolls
204KRNP5
Bore .631/.626 Extended Inner
Width 1.125/1.120
Planter Opener Wheels
206KRRB9
1" Bore Inner Width .9450/.9400
Planter
206KRR13
3⁄4" Bore
P204KRRB5
Bore .793/.788 Inner Width
.6988/.6938
Row Crop Machine
Idler Sprocket Bearing
for round Baler
207KRR3
Trencher
204RR6
E8728
Ground Bore .7505/.7500 Width
.610 O.D. 1.7805 Extra loose radial
play. Replaces 204KRNP2 E8728
Planter Gage Wheels
Large Inner Ring Bore Corner to
clear .090 R Shaft Fillet
207KRR8
Baler
P204RR6
Same as above except standard
radial play. Replaces 204KRNP2
Garden Tractor Mower
Spindle
Large Inner Ring Bore Corner to
clear .090 R Shaft Fillet Narrow
Inner .8499/.8399"
P207KRRB10
H204KRNP6
Bore, O.D., Width same as
P204KR2
Planter
11⁄4 Bore Flare out type R-Seal
with Shroud Cap
Corn Picker Snapping
Rolls
207KRR12
11⁄8" Hex Bore
Forage Harvester
204RR7
E8728
3⁄4" Bore 1.7805 O.D. .610 Width
Extra loose radial play. Replaces
204KRNP2 E8728
Rolling Cultivator Disk
Sprockets, Pulleys and
Disk Opener
P207KRNPB13
Bore 1.2505/1.2500 Extended
Inner 1.000/.945 on R-Seal Side
Corn Picker Gathering
Chain
205NPP2
Inner Width .6594/.6544
Miscellaneous
207KRR14
Bore 1.2530/1.2525
Disk Harrow Transport
Wheel
205KR3
3⁄4" Bore , Special Races, Heavy
R-Seal with Shroud Cap
Disk Hiller Planter and
Cotton Picker
207KYY
Double Lip Seal
Disk Harrow Transport
Wheel
205KP6
3⁄4" Bore Tri-Ply seal on one side
with shroud cap
Rolling Cultivator
Coulter Bearing
P208KRR4
A1849
Clutch Shaft
205KRR6
1⁄2" Bore extended inner ring
Windrow Digger
Bore 1.5312/1.5307 Large Inner
Ring Bore Corner to clear .090R
Shaft Fillet
205KRR7
1⁄2" Bore 1.500/1.495 Extended
Cone Roller Beet and
Potato Harvester
208NPPB5
Inner Ring with Offset race
Bore 1.4380/1.4375 Plya Seals
with Shroud Cap
Crank Pin for Square
Baler
209KRRB2
1" Hex Bore
Round Baler
304KR2
Offset Inner Ring with .7087/
.7037 Width
Tractor Water Pump
BB9105KRR2
1" Bore Inner Extended on one
side with 1.000/.995 Width Two
17/64 dia. holes in Inner Ring
180° apart
Hay Rake
side .689/.685
.9399 Extended on R-Seal side
205PPB7
FS544
15⁄16" Bore Tri-Ply Seals
1.375/1.3760 Inner Width
Rolling Cultivator
G205KPRB11
7⁄8" Hex Bore, One R-Seal and
Corn Head Mechanism
205PP9
FS544
3⁄4" Bore Inner Width
1.3750/1.3700 Tri-Ply Seals
Cultivator
205PP10
5⁄8" Bore Inner Width 1.375/1.370
Tri-Ply Seals
Potato Harvester
9113KDD3
FS264C
Cap Extends Past Inner Face
on one side
PTO Drive
1" Bore Inner Width 1.187/1.185
Tri-Ply Seals
Marker Wheel
9114KDD3
FS264C
Cap Extends Past Inner Face
on one side
PTO Drive
9117K3
Bore 3.2500/3.2492
O.D. 5.000/4.9992
PTO Drive
205PP11
one Tri-Ply Seal Inner Width
1.000/.975
DA
A
A
A
A
A
D35
•
BALL BEARINGS
XLS/BIC Series – Conrad Type
• An inch-dimension series with extra large diameters.
• Conrad or non-filling slot design.
• Compact sections for adaptability in applications where space is restricted.
d
D
C
Fillet Wt.
Static
Load
Number
d Diameter
C
Radius(1)
tolerance
D tolerance
tolerance
Rating
+0.000 mm +0.000 mm
+0.000 mm
Co
+0.0000"
+0.0000"
+0.0000"
to minus
to minus
to minus
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs.
N
lbs.
69.850
76.200
82.550
88.900
95.250
2.7500
3.0000
3.2500
3.5000
3.7500
0.015
0.015
0.020
0.020
0.020
0.0006
0.0006
0.0008
0.0008
0.0008
104.775
114.300
120.650
127.000
133.350
4.1250
4.5000
4.7500
5.0000
5.2500
0.015
0.015
0.020
0.020
0.020
0.0006
0.0006
0.0008
0.0008
0.0008
17.460
19.050
19.050
19.050
19.050
0.6875
0.7500
0.7500
0.7500
0.7500
0.13
0.13
0.13
0.13
0.13
0.005
0.005
0.005
0.005
0.005
1.2
1.2
1.2
1.7
1.6
0.047
0.047
0.047
0.065
0.063
0.449
0.567
0.626
0.671
0.712
0.99
1.25
1.38
1.48
1.57
22000
33500
30000
31500
34500
4900
7500
6700
7100
7800
28500
44000
35500
36500
39000
6400
9800
8000
8150
8650
XLS64K2
41BIC196
42BIC196
43BIC206
XLS72KD2
101.600
104.648
107.950
111.125
114.300
4.0000
4.1250
4.2500
4.3750
4.5000
0.020
0.020
0.020
0.020
0.020
0.0008
0.0008
0.0008
0.0008
0.0008
142.849
152.400
152.400
158.750
158.730
5.6240
6.0000
6.0000
6.2500
6.2490
0.025
0.025
0.025
0.025
0.025
0.0010
0.0010
0.0010
0.0010
0.0010
22.230
22.230
22.230
22.230
22.230
0.8750
0.8750
0.8750
0.8750
0.8750
0.13
0.20
0.20
0.20
0.20
0.005
0.008
0.008
0.008
0.008
2.0
2.5
2.5
2.5
2.0
0.080
0.100
0.100
0.100
0.080
0.794
1.471
1.374
1.542
1.121
1.75
3.24
3.03
3.40
2.47
41500
47500
47500
51000
54000
9500
10600
10600
11400
12000
47500
55000
55000
57000
60000
10600
12500
12500
12900
13400
45BIC206
46BIC216
47BIC216
48BIC225
XLS76K2
114.300
117.475
120.650
123.825
120.650
4.5000
4.6250
4.7500
4.8750
4.7500
0.020
0.020
0.025
0.025
0.025
0.0008
0.0008
0.0010
0.0010
0.0010
158.750
165.100
165.100
177.800
165.100
6.2500
6.5000
6.5000
7.0000
6.5000
0.025
0.025
0.025
0.025
0.025
0.0010
0.0010
0.0010
0.0010
0.0010
22.230
22.230
22.230
25.400
22.230
0.8750
0.8750
0.8750
1.0000
0.8750
0.20
0.20
0.25
0.25
0.25
0.008
0.008
0.010
0.010
0.010
2.5
2.5
2.5
2.5
1.7
0.100
0.100
0.100
0.100
0.065
1.442
1.615
1.512
2.254
1.157
3.18
3.56
3.33
4.97
2.55
51000
54000
57000
65500
57000
11400
12000
12700
15000
12700
57000
58500
61000
75000
61000
12900
13200
13700
16600
13700
XLS80K2
50BIC225
51BIC240
52BIC240
53BIC247
127.000
127.000
130.175
133.350
136.525
5.0000
5.0000
5.1250
5.2500
5.3750
0.025
0.025
0.025
0.025
0.025
0.0010
0.0010
0.0010
0.0010
0.0010
177.775
177.800
184.150
184.150
190.500
6.9990
7.0000
7.2500
7.2500
7.5000
0.025
0.025
0.030
0.030
0.030
0.0010
0.0010
0.0012
0.0012
0.0012
25.400
25.400
25.400
25.400
25.400
1.0000
1.0000
1.0000
1.0000
1.0000
0.25
0.25
0.25
0.25
0.25
0.010
0.010
0.010
0.010
0.010
2.0
2.5
2.5
2.5
2.5
0.080
0.100
0.100
0.100
0.100
1.611
2.3
2.5
2.4
2.6
3.55
5.0
5.5
5.2
5.7
67000
65500
69500
69500
75000
15000
15000
15600
15600
16600
72000
75000
76500
76500
80000
16300
16600
17300
17300
17600
55BIC247
56BIC251
57BIC251
58BIC258
60BIC258
139.700
142.875
146.050
149.225
152.400
5.5000
5.6250
5.7500
5.8750
6.0000
0.025
0.025
0.025
0.025
0.025
0.0010
0.0010
0.0010
0.0010
0.0010
190.500
196.850
196.850
203.200
203.200
7.5000
7.7500
7.7500
8.0000
8.0000
0.030
0.030
0.030
0.030
0.030
0.0012
0.0012
0.0012
0.0012
0.0012
25.400
25.400
25.400
25.400
25.400
1.0000
1.0000
1.0000
1.0000
1.0000
0.25
0.25
0.25
0.25
0.25
0.010
0.010
0.010
0.010
0.010
2.5
2.5
2.5
2.5
2.5
0.100
0.100
0.100
0.100
0.100
2.5
2.7
2.5
2.8
2.6
5.4
5.9
5.6
6.1
5.8
75000
75000
75000
78000
78000
16600
16600
16600
17300
17300
80000
80000
80000
81500
81500
17600
17600
17600
18000
18000
62BIC290
65BIC298
67BIC301
70BIC309
72BIC340
158.750
165.100
171.450
177.800
184.150
6.2500
6.5000
6.7500
7.0000
7.2500
0.025
0.025
0.025
0.025
0.030
0.0010
0.0010
0.0010
0.0010
0.0012
215.900
222.250
228.600
241.300
247.650
8.5000
8.7500
9.0000
9.5000
9.7500
0.030
0.030
0.030
0.030
0.030
0.0012
0.0012
0.0012
0.0012
0.0012
28.575
28.575
28.575
31.750
31.750
1.1250
1.1250
1.1250
1.2500
1.2500
0.25
0.25
0.25
0.25
0.31
0.010
0.010
0.010
0.010
0.012
3.0
3.0
3.0
3.0
3.0
0.120
0.120
0.120
0.120
0.120
3.5
3.6
3.7
4.8
4.9
7.7
7.9
8.2
10.6
10.8
104000
98000
104000
116000
122000
23200
22000
23200
26000
27500
106000
102000
104000
118000
122000
23600
22800
23600
26500
27000
75BIC348
77BIC351
80BIC359
82BIC390
85BIC391
190.500
196.850
203.200
209.550
215.900
7.5000
7.7500
8.0000
8.2500
8.5000
0.030
0.030
0.030
0.030
0.030
0.0012
0.0012
0.0012
0.0012
0.0012
254.000 10.0000
266.700 10.5000
273.050 10.7500
279.400 11.0000
292.100 11.5000
0.036
0.036
0.036
0.036
0.036
0.0014
0.0014
0.0014
0.0014
0.0014
31.750
34.925
34.925
34.925
38.100
1.2500
1.3750
1.3750
1.3750
1.5000
0.31
0.31
0.31
0.31
0.31
0.012
0.012
0.012
0.012
0.012
3.0
3.0
3.0
3.0
3.0
0.120
0.120
0.120
0.120
0.120
5.0
6.3
6.5
6.6
8.2
11.1
13.9
14.2
14.6
18.0
122000
146000
146000
153000
166000
27500
32500
32500
34500
37500
122000
143000
143000
150000
163000
27000
32500
32500
33500
36500
87BIC393
90BIC401
95BIC430
100BIC439
105BIC470
222.250 8.7500
228.600 9.0000
241.300 9.5000
254.000 10.0000
266.700 10.5000
0.030
0.030
0.030
0.036
0.036
0.0012
0.0012
0.0012
0.0014
0.0014
298.450 11.7500
304.800 12.0000
323.850 12.7500
336.550 13.2500
355.600 14.0000
0.036
0.036
0.041
0.041
0.041
0.0014
0.0014
0.0016
0.0016
0.0016
38.100
38.100
41.275
41.275
44.450
1.5000
1.5000
1.6250
1.6250
1.7500
0.31
0.31
0.36
0.36
0.36
0.012
0.012
0.014
0.014
0.014
3.0
3.0
4.0
4.0
4.0
0.120
0.120
0.160
0.160
0.160
8.4
8.6
10.6
11.1
13.5
18.5
18.9
23.4
24.4
29.8
176000
176000
200000
212000
255000
40000
40000
45000
47500
57000
170000
166000
190000
193000
224000
38000
37500
42500
43000
50000
110BIC479
115BIC510
120BIC519
125BIC550
135BIC580
279.400 11.0000
292.100 11.5000
304.800 12.0000
317.500 12.5000
342.900 13.5000
0.036
0.036
0.036
0.041
0.041
0.0014
0.0014
0.0014
0.0016
0.0016
368.300 14.5000
387.350 15.2500
406.400 16.0000
419.100 16.5000
457.200 18.0000
0.041
0.041
0.046
0.046
0.046
0.0016
0.0016
0.0018
0.0018
0.0018
44.450
47.625
50.800
50.800
57.150
1.7500
1.8750
2.0000
2.0000
2.2500
0.36
0.36
0.36
0.41
0.41
0.014
0.014
0.014
0.016
0.016
4.0
5.0
5.0
5.0
5.0
0.160
0.200
0.200
0.200
0.200
14.1
16.9
20.0
20.7
27.9
31.0
37.2
44.1
45.7
61.6
255000
280000
315000
325000
415000
57000
64000
71000
73500
93000
220000
240000
255000
265000
315000
50000
54000
58500
60000
71000
140BIC588
145BIC610
150BIC613
155BIC615
160BIC647
355.600 14.0000
368.300 14.5000
381.000 15.0000
393.700 15.5000
406.400 16.0000
0.041
0.041
0.041
0.041
0.046
0.0016
0.0016
0.0016
0.0016
0.0018
469.900 18.5000
495.300 19.5000
508.000 20.0000
520.700 20.5000
546.100 21.5000
0.046
0.046
0.051
0.051
0.051
0.0018
0.0018
0.0020
0.0020
0.0020
57.150
63.500
63.500
63.500
69.850
2.2500
2.5000
2.5000
2.5000
2.7500
0.41
0.41
0.41
0.41
0.46
0.016
0.016
0.016
0.016
0.018
5.0
5.0
5.0
5.0
5.0
0.200
0.200
0.200
0.200
0.200
28.8
37.4
38.5
39.5
48.8
63.4
82.5
84.8
87.1
107.6
415000
490000
490000
490000
585000
93000
110000
110000
110000
132000
310000
355000
355000
345000
400000
69500
80000
80000
78000
90000
165BIC660
170BIC661
175BIC680
180BIC687
185BIC695
419.100 16.5000
431.800 17.0000
444.500 17.5000
457.200 18.0000
469.900 18.5000
0.046
0.046
0.046
0.046
0.046
0.0018
0.0018
0.0018
0.0018
0.0018
558.800 22.0000
571.500 22.5000
596.900 23.5000
609.600 24.0000
622.300 24.5000
0.051
0.051
0.051
0.051
0.051
0.0020
0.0020
0.0020
0.0020
0.0020
69.850
69.850
76.200
76.200
76.200
2.7500
2.7500
3.0000
3.0000
3.0000
0.46
0.46
0.46
0.46
0.46
0.018
0.018
0.018
0.018
0.018
5.0
5.0
5.0
5.0
5.0
0.200
0.200
0.200
0.200
0.200
50.2
51.4
63.8
65.3
66.8
110.6
113.3
140.8
144.0
147.3
620000
620000
710000
710000
710000
137000
137000
160000
160000
160000
415000 93000
415000 93000
455000 102000
455000 102000
455000 102000
190BIC696
195BIC710
200BIC717
205BIC725
210BIC726
482.600 19.0000
495.300 19.5000
508.000 20.0000
520.700 20.5000
533.400 21.0000
0.046
0.051
0.051
0.051
0.051
0.0018
0.0020
0.0020
0.0020
0.0020
647.700 25.5000
660.400 26.0000
673.100 26.5000
698.500 27.5000
711.200 28.0000
0.076
0.076
0.076
0.076
0.076
0.0030
0.0030
0.0030
0.0030
0.0030
82.550
82.550
82.550
88.900
88.900
3.2500
3.2500
3.2500
3.5000
3.5000
0.46
0.46
0.51
0.51
0.51
0.018
0.018
0.020
0.020
0.020
5.0
5.0
5.0
5.0
5.0
0.200
0.200
0.200
0.200
0.200
80.7
82.4
84.3
97.5
99.7
177.9
181.7
185.9
215.0
219.8
800000
800000
850000
965000
1020000
180000
180000
190000
216000
228000
500000
500000
510000
570000
585000
XLS44K
XLS48K2
XLS52K
XLS56K
XLS60K2
A
A
A
A
A
•
D
Extended
Dynamic
Load
Rating
CE (2)
D36
112000
112000
114000
129000
132000
BIH Series – Maximum Capacity Type
• An inch-dimension series with extra large diameters.
• Maximum capacity design.
• Feature a counterbored outer ring to permit increased number of balls.
• Can carry thrust in one direction only, against the full shouldered side
of the outer race.
• Compact sections for adaptability to applications where space is
d
D
restricted.
C
DIMENSIONS – TOLERANCES BIH SERIES
Fillet Wt.
Static
Load
Number
d Diameter
C
Radius(1)
tolerance
D tolerance
tolerance
Rating
+0.000 mm +0.000 mm
+0.000 mm
Co
+0.0000"
+0.0000"
+0.0000"
to minus
to minus
to minus
Extended
Dynamic
Load
Rating
CE (2)
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
kg
lbs.
N
lbs.
N
lbs.
41BIH196
42BIH196
43BIH206
45BIH206
46BIH216
104.775
107.950
111.125
114.300
117.475
4.1250
4.2500
4.3750
4.5000
4.6250
0.020
0.020
0.020
0.020
0.020
0.0008
0.0008
0.0008
0.0008
0.0008
152.400
152.400
158.750
158.750
165.100
6.0000
6.0000
6.2500
6.2500
6.5000
0.025
0.025
0.025
0.025
0.025
0.0010
0.0010
0.0010
0.0010
0.0010
22.23
22.23
22.23
22.23
22.23
0.8750
0.8750
0.8750
0.8750
0.8750
0.20
0.20
0.20
0.20
0.20
0.008
0.008
0.008
0.008
0.008
2.5
2.5
2.5
2.5
2.5
0.10
0.10
0.10
0.10
0.10
1.411
1.321
1.483
1.383
1.561
3.11
2.91
3.27
3.05
3.44
63000
71000
51000
75000
80000
14000
16000
11400
16600
18000
65500
72000
57000
73500
76500
14600
16300
12900
16600
17300
48BIH225
50BIH225
51BIH240
52BIH240
53BIH247
123.825
127.000
130.175
133.350
136.525
4.8750
5.0000
5.1250
5.2500
5.3750
0.025
0.025
0.025
0.025
0.025
0.0010
0.0010
0.0010
0.0010
0.0010
177.800
177.800
184.150
184.150
190.500
7.0000
7.0000
7.2500
7.2500
7.5000
0.025
0.025
0.030
0.030
0.030
0.0010
0.0010
0.0012
0.0012
0.0012
25.40
25.40
25.40
25.40
25.40
1.0000
1.0000
1.0000
1.0000
1.0000
0.25
0.25
0.25
0.25
0.25
0.010
0.010
0.010
0.010
0.010
2.5
2.5
2.5
2.5
2.5
0.10
0.10
0.10
0.10
0.10
2.209
2.3
2.5
2.4
2.6
4.87
5.0
5.5
5.2
5.7
104000
104000
108000
104000
112000
23200
23200
24000
23200
25000
100000
100000
102000
100000
104000
22400
22400
22800
22400
23200
55BIH247
56BIH251
57BIH251
58BIH258
60BIH258
139.700
142.875
146.050
149.225
152.400
5.5000
5.6250
5.7500
5.8750
6.0000
0.025
0.025
0.025
0.025
0.025
0.0010
0.0010
0.0010
0.0010
0.0010
190.500
196.850
196.850
203.200
203.200
7.5000
7.7500
7.7500
8.0000
8.0000
0.030
0.030
0.030
0.030
0.030
0.0012
0.0012
0.0012
0.0012
0.0012
25.40
25.40
25.40
25.40
25.40
1.0000
1.0000
1.0000
1.0000
1.0000
0.25
0.25
0.25
0.25
0.25
0.010
0.010
0.010
0.010
0.010
2.5
2.5
2.5
2.5
2.5
0.10
0.10
0.10
0.10
0.10
2.5
2.7
2.5
2.8
2.6
5.4
5.9
5.6
6.1
5.8
112000
116000
116000
118000
118000
25000
26000
26000
26500
26500
104000
106000
106000
108000
108000
23200
23600
23600
24000
24000
62BIH290
65BIH298
67BIH301
70BIH309
72BIH340
158.750
165.100
171.450
177.800
184.150
6.2500
6.5000
6.7500
7.0000
7.2500
0.025
0.025
0.025
0.025
0.030
0.0010
0.0010
0.0010
0.0010
0.0012
215.900
222.250
228.600
241.300
247.650
8.5000
8.7500
9.0000
9.5000
9.7500
0.030
0.030
0.030
0.030
0.030
0.0012
0.0012
0.0012
0.0012
0.0012
28.575
28.575
28.575
31.750
31.750
1.1250
1.1250
1.1250
1.2500
1.2500
0.25
0.25
0.25
0.25
0.31
0.010
0.010
0.010
0.010
0.012
3.0
3.0
3.0
3.0
3.0
0.12
0.12
0.12
0.12
0.12
3.5
3.6
3.7
4.8
4.9
7.7
7.9
8.2
10.6
10.8
146000
153000
160000
180000
186000
33500
34500
35500
40500
42500
134000
137000
137000
160000
160000
30000
30500
31000
35500
36000
75BIH348
77BIH351
80BIH359
82BIH390
85BIH391
190.500
196.850
203.200
209.550
215.900
7.5000
7.7500
8.0000
8.2500
8.5000
0.030
0.030
0.030
0.030
0.030
0.0012
0.0012
0.0012
0.0012
0.0012
254.000 10.0000
266.700 10.5000
273.050 10.7500
279.400 11.0000
292.100 11.5000
0.036
0.036
0.036
0.036
0.036
0.0014
0.0014
0.0014
0.0014
0.0014
31.750
34.925
34.925
34.925
38.100
1.2500
1.3750
1.3750
1.3750
1.5000
0.31
0.31
0.31
0.31
0.31
0.012
0.012
0.012
0.012
0.012
3.0
3.0
3.0
3.0
3.0
0.12
0.12
0.12
0.12
0.12
5.0
6.3
6.5
6.6
8.2
11.1
13.9
14.2
10.6
18.0
193000
228000
236000
245000
270000
43000
51000
53000
55000
61000
163000
193000
200000
200000
224000
36500
44000
45000
45500
50000
87BIH393
90BIH401
95BIH430
100BIH439
105BIH470
222.250 8.7500
228.600 9.0000
241.300 9.5000
254.00 10.0000
266.700 10.5000
0.030
0.030
0.030
0.036
0.036
0.0012
0.0012
0.0012
0.0014
0.0014
298.450 11.7500
304.800 12.0000
323.850 12.7500
336.550 13.2500
355.600 14.0000
0.036
0.036
0.036
0.041
0.041
0.0014
0.0014
0.0014
0.0016
0.0016
38.100
38.100
41.275
41.275
44.450
1.5000
1.5000
1.6250
1.6250
1.7500
0.31
0.31
0.36
0.36
0.36
0.012
0.012
0.014
0.014
0.014
3.0
3.0
4.0
4.0
4.0
0.12
0.12
0.16
0.16
0.16
8.4
8.6
10.6
11.1
13.5
18.5
18.9
23.4
24.4
29.8
270000
280000
315000
325000
400000
61000
63000
71000
73500
90000
224000
228000
255000
260000
300000
50000
51000
57000
58500
68000
110BIH479
115BIH510
120BIH519
135BIH580
140BIH588
279.400 11.0000
292.100 11.5000
304.800 12.0000
342.900 13.5000
355.600 14.0000
0.036
0.036
0.036
0.041
0.041
0.0014
0.0014
0.0014
0.0016
0.0016
368.300 14.5000
387.350 15.2500
406.400 16.0000
457.200 18.0000
469.900 18.5000
0.041
0.041
0.046
0.046
0.046
0.0016
0.0016
0.0018
0.0018
0.0018
44.450
47.625
50.800
57.150
57.150
1.7500
1.8750
2.0000
2.2500
2.2500
0.36
0.36
0.36
0.41
0.41
0.014
0.014
0.014
0.016
0.016
4.0
5.0
5.0
5.0
5.0
0.16
0.20
0.20
0.20
0.20
14.1
16.9
20.0
27.9
28.8
31.0
37.2
44.1
61.6
63.4
415000
465000
510000
655000
680000
93000
104000
116000
146000
150000
305000
335000
355000
425000
430000
69500
75000
80000
95000
96500
DA
A
A
A
A
D37
•
A
BALL BEARINGS
Extra Large 100 Series
• Dimensions originally established to meet specific design
•
•
•
•
requirements, before standard dimensions were established
by the American Bearing Manufacturers Association (ABMA).
A metric series.
Available in the 100 Series (extra light).
Available in a radially-fitted counterbore type, having a
maximum complement of balls.
Identified by the suffix “WI,” these are designed to take thrust
in one direction only.
d
D
C
C
Filling-Slot Type
Counterbore Type
D
A
Bearing Bore
Outside
Width
Fillet
Wt.
Number
d
Diameter
C
Radius(1)
D
tolerance
tolerance
+0.00 mm
Filling- Counter- One +0.000 mm
+0.000 mm
-.25 mm
Filling-
Counter-
bore
Shield
+0.0000"
+0.0000"
+0.000"
slot
bore
Shielded
slot
Type
Type
D to minus
to minus
-.010"
Type
Type
Type
mm in.
mm in.
mm
in.
mm in.
mm in.
mm in.
kg lbs.
kg lbs. kg lbs. 120W2
122W
124W
126W
128W
—
122WI
124WI
126WI
128WI
130W
132W
134W
—
138W
—
—
—
—
—
120WD2N
122WD2N(3)
124WD
126WD
128WD
100
110
120
130
140
3.9370
4.3307
4.7244
5.1181
5.5118
0.020
0.020
0.020
0.025
0.025
0.0008
0.0008
0.0008
0.0010
0.0010
160
175
190
205
220
6.2992
6.8898
7.4803
8.0709
8.6614
0.025
0.025
0.030
0.030
0.030
0.0010
0.0010
0.0012
0.0012
0.0012
28
30
32
34
36
1.102(4)
1.181(4)
1.260(4)
1.339
1.417
2.01
2.01
2.01
2.01
2.01
0.079
0.079
0.079
0.079
0.079
2.041
2.762
3.475
4.336
5.239
4.50
6.09
7.66
9.56
11.55
—
2.835
3.538
4.318
5.244
130WD
132WD
—
136WD2N
—
150
160
170
180
190
5.9055
6.2992
6.6929
7.0866
7.4803
0.025
0.025
0.025
0.025
0.03
0.0010
0.0010
0.0010
0.0010
0.0120
235 9.2520
250 9.8425
265 10.4331
280 11.0236
300 11.8110
0.030
0.030
0.035
0.035
0.035
0.0012
0.0012
0.0014
0.0014
0.0014
38
40
42
49
46
1.496
1.575
1.654
1.929
1.811(2)
2.01
2.49
2.49
2.49
2.49
0.079
0.098
0.098
0.098
0.098
6.278
7.394
9.049
—
12.928
13.84
16.30
19.95
—
28.50
—
—
—
—
—
A
(2) +.00 mm, -25 mm (+000”, -.010").
(3) 35 mm width.
(4) Width tolerance is +.00 mm, -.20 mm (+.000”, -.008”).
A
A
•
A
D38
—
6.25
7.80
9.52
11.56
—
—
—
—
—
2.041
3.157
3.466
4.332
5.294
Static
Load
Rating
Co
N
lbs.
4.50 75000 17000
6.96 80000 18000
7.64 98000 22400
9.55 110000 24500
11.67 122000 27000
6.437 14.19
7.484 16.50
— —
11.004 24.26
— —
140000
160000
180000
200000
245000
31500
35500
40000
45000
56000
Extended
Dynamic
Load
CE (5)
N
lbs.
106000 24000
116000 26000
140000 31500
146000 33500
163000 36500
183000 41500
208000 46500
224000 51000
245000 55000
285000 64000

daaaaaaaaaa - Industrial GP

Transcription

Similar documents

Timken Ball Bearing Catalog

PEER Agricultural Catalog 2015

Wireloc - LTS Energy

List of Texas Non-Subscriber Businesses