N2 Soldering Iron (Iron holder with a sleep mode)

N2 Soldering Iron (Iron holder with a sleep mode)
Thank you for purchasing the FM-2026 soldering iron.
The FM-2026 soldering iron is designed to supply hot gas to the soldering area. This can
increase soldering efficiency, as the gas pre-heats the work area.
When the heated gas is nitrogen (N2), soldering efficiency is further improved as the nitrogen
materially reduces the amount of oxygen in the ambient atmosphere. Please read this manual
before operating the FM-2026. Keep this manual readily accessible for reference.
CAUTION When you use the FM-2026 for the first time, note that calibration is required before
starting operation. Read the instruction manual for the station used in conjunction with
the FM-2026 soldering iron.
Station : FM-202, FM-203, FM-204, FM-205, FM-206
N2 generator :
N2 station :
If used in conjunction with FM-202;
Insert the tip ID end of the tip into the process
gate until the buzzer sounds once.
If used in conjunction with HAKKO FX-950, FX951, FX-952, FM-203, FM-204,
FM-205 or FM-206 station;
Connect the station to the HAKKO FM-2026. Set
the desired temperature and the heat control
begins. (Please refer to the HAKKO FX-950, FX951,FX-952, FM-203, FM-204, FM-205 or FM-206
instruction manual.)
●FM-203
Measure the tip temperature when it is stabilized.
Input the offset value so that it will become to the
measured temperature. (Please refer to the
HAKKO FX-950, FX-951, FX-952, FM-203, FM204, FM-205 or FM-206 instruction manual.)
●FM-206
Jack to
Connecting cable
When using the sleep function,
insert one end of the connecting
cable into the jack at the back of
the iron holder and the other end
into the jack at the back of the
soldering station to connect them.
Refer to the instruction manual for
the HAKKO FX-950, FX-951, FX-952,
FM-203, FM-204 and FM-206.
CAUTION
Copyright © 2013 HAKKO Corporation. All Rights Reserved.
2013.11
MA01657XZ131101
ø2
(ø0.08)
(0 2.1
.
(0 0.9 08)
.0
4)
T17-BCM2 SHAPE-2BC Bevel
with indent
8
1. 07)
.
(0
This product includes such features as electrically
conductive plastic parts and grounding of the
handpiece and station as measures to protect the
device to be soldered from the effects of static
electricity. Be sure to observe the following
instructions:
1. The handle and other plastic parts are not
insulators, they are conductors. When replacing
parts or repairing, take sufficient care not to
expose live electrical parts or damage insulation
materials.
2. Be sure to ground the unit during use.
11.5
(0.45)
T17-BCM3 SHAPE-3BC Bevel
with indent
Tip Shape
2BC, 2BCF, 2BCM
0.2J
1.6D, 0.5B, 2.4D
0.8D
1BC, 1BCF
3BC, 3BCF, 3BCM
KU
KF
Part No.
T17-BC2, T17-BCF2, T17-BCM2
T17-J02
T17-D16, T17-B2, T17-D24
T17-D08
T17-BC1, T17-BCF1
T17-BC3, T17-BCF3, T17-BCM3
T17-KU
T17-KF
Part No.
B2706
B2707
B2708
B2709
B2899
B2900
B2901
B2923
Part Name
Nozzle assembly A
Nozzle assembly B
Nozzle assembly C
Nozzle assembly D
Nozzle assembly F
Nozzle assembly G
Nozzle assembly H
Nozzle assembly J