technical information

T
ECHNICAL INFORMATION
Models No.
LS1212
Description
305mm Slide Compound Saw
New Tool
80
0(
31
-1
/2"
)
Model LS1212 is Iimproved version of Model LS1211.
Its brief benefits are;
*Bevel cuts in left and right
*More accurate cut
*Excellent chip/sawdust ejection
*Electronic speed control feature
Less reaction at starting by soft start feature
Clean cut surface by steady speed feature
Very quiet by low speed at no load
*Blocking mechanism at the rest position for European
countries to comply with CE-regulations.
690(27-1/4")
CONCEPTION AND MAIN APPLICATIONS
590(
23-1
/4")
Specifications
Voltage (V)
Current (A)
100
115
200
220
230
240
15.0
15.0
8.6
7.9
7.5
7.2
Cycle (Hz)
50/60
50/60
50/60
50/60
50/60
50/60
Continuous Rating (W)
Input
Output
1430
650
1650
1000
1650
1000
1650
1000
1650
1000
1650
1000
Max. Output(W)
2300
2300
2300
2300
2300
2300
3200rpm
25.4mm(1")
290mm(11-3/8")-305mm(12")
22kg(48.5 lbs)
2.5m(8.2 ft)
No Load Speed
Arbor diameter
Blade diameter
Net weight
Power supply cord
Max cutting capacities (HxW) with saw blade 255mm
Miter angle
0°
45°
(left and right)
60°(right)
Wood
facing
45° (left)
Bevel angle
0°
45° (right)
34mm 69mm(2-3/4")x230mm(9")
49mm(1-15/16")x230mm(9")
120mm(4-3/4")x230mm(9")
55mm(2-3/16")x310mm(12-1/4") 107mm(4-1/4")x298mm(11-3/4") 40mm(1-9/16")x298mm(11-3/4")
55mm(2-3/16")x310mm(12-1/4") 98mm(3-7/8")x310mm(127-1/4") 35mm(1-3/8")x310mm(12-1/4")
°
24mm 69mm(2-3/4")x162mm(6-3/8")
120mm(4-3/4")x162mm(6-3/8") 49mm(1-15/16")x162mm(3-3/8")
61mm(2-3/8")x211mm(8-1/4") 107mm(4-1/4")x211mm(8-1/4") 40mm(1-9/16")x211mm(8-1/4")
55mm(2-3/16")x220mm(8-5/8") 98mm(3-7/8")x220mm(8-5/8") 35mm(1-3/8")x220mm(8-5/8")
120mm(4-3/4")x115mm(4-1/2")
17mm
107mm(4-1/4")x149mm(5-7/8")
98mm(3-7/8")x155mm(6-1/8")
Standard equipment
Vise Ass'y(Vertical cal Vise)---------------------- 1 pc.
Socket Wrench 13---------------------------------- 1 pc.
Dust Bag Ass'y-------------------------------------- 1 pc.
Triangular Rule ------------------------------------- 1 pc.
Holder
------------------------------------------- 1 pc.
Switch Button(as s spare) ------------------------ 1 pc.
T. C. T. Saw Blade
--- 1 pc.
The standard equipment for the tools shown may differ form country to country.
Optional accessories
Vise Ass'y(Horizontal Vise)
Set Plate Ass'y Sub Fence (R) Set
Elbow Elbow
Crown Molding Stopper
Features and benefits
1.Double insulated
2.See the attached sheets for more information.
Elecronic speed control feature
Less shock at starting by soft start feature
Clean cut surface by steady speed feature
Very quiet by low speed at no load
Makita
Hitachi
LS1212
C12FSA
84dB
84dB
Makita
LS1211
93dB
(=total noise of eight LS1212's)
Handle for carrying
More efficient chip/sawdust ejection
Less ejection toward operater
Two poles for sliding and rigider arm
Accurate cutting can be performed.
High-rigidity arm
Accurate cutting
can be performed.
Movable sub fence
Material can be held widely at 0
and right bevel cut.
Removable sub fence
(Optional accessory)
Material can be held widely at 0°
and left bevel cut.
Bevel cut can be performed.
(45° in either way)
Arm can be tilted by loosening lever.
0° cut is set with positive stop.
Crown Molding Stopper Set
Convenient for setting
crown molding slantwise
Both vertical vise(standard accessory)
and horizontal vise(optional accessory)
can be attached.
Comfortable slide stopper
Sliding is locked by tighting the knob.
Easy to actuate owing to located
at the operater side
Positive stops at turn base
can be released by pushing the lever down
for angles (left or right) 0°,15°,22.5°,30° ,45°
and 60°(right)
Comparision
Makita
Model No.
Blade diameter
305mm(12")
LS1211
305mm(12")
Rated current (A)(100V)
15
15
1650
1650(110-130V)
1800(200-240V)
4000
LS1212
Input(w)
3200
No load speed(rpm)
Steady Speed
Electronical Speed
Control feature
Yes
Yes
Soft start
L:45° - R:45°
Bevel angle
Miter angle
L:47° - R:60°
Net weight
22.0kg(48.5 lbs)
800x590x690mm
(31-1/2"x23-1/4"x27-1/4")
Dimension
(LxWxH)
No
No
L:45° - R:45°
L:60° - R:60°
23.2kg(51.2 lbs)
1040x605x620mm
(41"x23-3/4"x23-3/8")
Max. cutting capacities
Makita
LS1212
Model No.
Bevel angle
0°
Miter
Angle
0°
45°
Wood facing
34mm (1-15/16")
R:60°
45°
Wood facing
30mm (1-3/16")
107x298mm
(4-1/4"x11-3/4")
98x310mm
(3-7/8"x12-1/4")
Without wood facing
Wood facing
24mm (15/16")
120x162mm
(4-3/4"x6-3/8")
107x211mm
(4-1/4"x8-5/6")
98x220mm
(3-7/8"x8-5/8")
Wood facing
21mm (13/16")
Wood facing
17mm (11/16")
Without wood facing
0°
120x230mm
(4-3/4"x9")
Without wood facing
Without wood facing
L:45°
LS1211
120x115mm
(4-3/4"x4-1/4")
107x149mm
(4-1/4"x5-7/8")
98x155mm
(3-7/8"x6-1/8")
Without wood facing
Wood facing
15mm (9/16")
Without wood facing
120x230mm
(4-3/4"x9")
107x290mm
(4-1/4"x11-3/8")
94x310mm
(3-11/16"x12-1/4")
120x162mm
(4-3/4"x6-3/8")
107x205mm
(4-1/4"x8-1/8")
94x219mm
(3-11/16"x8-5/8")
120x115mm
(4-3/4"x4-1/2")
107x145mm
(4-1/4"x5-3/4")
94x155mm
(3-11/16"x6-1/8")
Wood facing
34mm (1-15/16")
69x230mm
(2-3/4"x9")
Wood facing
30mm (1-3/16")
65x230mm
(2-9/16"x9")
Without wood facing
61x298mm
(2-3/8"x11-3/4")
55x310mm
(2-13/16"x12-1/4")
Without wood facing
Wood facing
24mm (15/16")
69x162mm
(2-3/4"x6-3/8")
Wood facing
21mm (13/16")
57x290mm
(2-1/4"x11-3/8")
48x310mm
(1-7/8"x12-1/4")
65x162mm
(2-9/16"x6-3/8")
Without wood facing
61x211mm
(2-3/8"x8-5/6")
55x220mm
(2-3/16"x8-5/8")
Without wood facing
57x205mm
(2-1/4"x8-1/8")
48x219mm
(1-7/8"x8-5/8")
Max. cutting capacities
Makita
LS1212
Model No.
Bevel angle
LS1211
Miter
Angle
Wood facing
34mm (1-15/16")
R:45°
0°
45°
Without wood facing
Wood facing
24mm (15/16")
Without wood facing
Wood facing
30mm (1-3/16")
49x230mm
(1-15/16"x9")
40x298mm
(1-9/16"x11-3/4")
35x310mm
(1-3/8"x12-1/4")
49x162mm
(1-15/16"x6-3/8")
Without wood facing
Wood facing
21mm (13/16")
40x211mm
(1-9/16"x8-5/6")
35x220mm
(1-3/8"x8-5/8")
Without wood facing
49x230mm
(1-15/16"x9")
40x290mm
(1-9/16"x11-3/8")
31x310mm
(1-1/4"x12-1/4")
49x162mm
(1-15/16"x6-3/8")
40x205mm
(1-9/16"x8-1/8")
31x219mm
(1-1/4"x8-5/8")
<Note>MiterAngle R;45° only
Repair
Since this machine has many movable functions(up/down swinging of motor, left/right turning of turn base,
left/right tilting of motor, back/forth sliding of motor), use care that each part may not move unintentionally in
repairing and adjustment.
Greasing :
Grease the MAKITA GREASE on the movable/sliding faces on the points shown below before assembling.
Up/down swinging points of blade case
Blade case, arm, pipe 16-113
Arm beveling points in left/right and movable points
Arm and arm holder complete(faucet joint and center shaft)
Guide plate face(the side where steel ball hit), edge on the hexagon bolt M10x90
Support point for turn base turning in left/right and moving points
Armature
Turn base, Boss at center on the base, Left/right moving face on the base
Edge of link plate
Outer circumference on the center plate
Side face on the hole for mounting the blade case and compression spring
Moving face on the sub-fence
Screw on the stopper holder
Oil applying
Slide plate
Pan head screw M5
Bearing retainer 66
Disassembling/assembling of gear
Unless the armature is disconnected, the gear cannot be disassembled.
Accordingly first take away the armature.
To disconnect the gear, remove the pan head screws M5(2 pieces) for
holding the bearing retainer 66 from inside the blade case.
To assemble the gear, proceed in the following steps.
i) Set the rubber ring 20 on the spiral bevel gear 33.
ii) Place the flat washer 14 in the spindle, insert the key 4, and set the spiral bevel gear 33 mounted with the rubber
ring 20.
iii) To assemble the circle clip(shaft)S-14, use the arbor etc. to press the spiral bevel gear 33, and assemble it while
crushing the rubber ring 20. After assembling, make sure that the circle clip(shaft) S-14 has been securely
inserted in the groove.
Rubber ring 20
Flat washer 14
Key 4
Spindle
Circle clip(shaft) S-14
Spiral bevel gear 33
For disassembling of blade case, compression ring 28 and link plate, proceed in the same procedures as LS1011
and LS1030.
Assembling of the bearing box B complete
For this machine, the bearing box B complete is screwed so that the distance between the shaft receivers of two
slide poles can be adjusted. Therefore assemble in the following orders.
i) Temporarily mount the bearing box B on the turn base.
ii) Mount the arm holder complete and then fix the bearing box B while the arm holder complete is being inserted
in the deepest.
Bearing box B
Turn base
Arm holder
complete
iii) Slide the arm holder complete and fix the square rod complete while the groove on the slide pipe edge comes
nearest to the bearing 30.
Square rod complete
Bearing 30
(already inserted
into the turn base)
Rubber pin
iv) Assemble the square rod complete in a way that the
rubber pin comes at bearing 30 side.
Adjusting the ball notch strength with the beveling at 0
(right angle)
For this machine, the right angle corner is positioned
without clearance using the ball notch
comprising two
steel balls. If the ball notch functions too strong or
weak when the motor is inclined, turn the hexagon
holed stop screw at right side to adjust the function. For
reference of the functioning strength, make
arrangement in a degree that the base leg may not float
when the motor is inclined(when the ball notch is
disconnected).
Arm holder
The screw at left should be
positioned while returned by 1/2-turn
from the same face as the aluminum
face and do not adjust it.
Use the screw at right
to adjust the function.
Fastening the hexagon bolt M8 for mounting the turn base
Adjust the fastening degree of hexagon bolt M8 at the
center on the turn base so that the turn base can be smoothly
turned without clearance.
Turn base
Hexagon bolt M8
Fastening the hexagon lock nut M8 for mounting the arm
Adjust the fastening degree of the hexagon lock nut M8 at
center of arm turning so that the arm can be inclined in
left/right smoothly without clearance.
Arm
Hexagon lock nut M8
Assembling of the pin holder
Since the lock pin for positive stopping may wrongly move depending on the assembling conditions of the pin
holder, assemble the pin holder while checking if the lock pin can move smoothly.
Assembling of the pipe 9-200
Once the grip has been removed from the turn base, the pipe inside the turn base may be dropped. If the pipe 9-200
has been dropped, also remove the knob 48 complete from the turn base and then assemble through the screw hole
of the turn base edge while the knob 48 complete and pipe 9-200 are being inserted in the grip.
Turn base
Grip
Knob 48 complete
Base
Pin holder
Lock pin
Pipe 9-200
Assembling of the grip 37 and screw M8x320
Adjust the length of the screw M8x320 so that you can get the size shown on the below figure. To fasten the
hexagon nut M8, fix under the fastening torque of more than 100 kgf.cm.
Hexagon nut M8
Screw M8x320
Grip 37
303mm
Circuit drawing
<Low pressure specifications>
100V area
Connector at closed end
Orange color
Orange color
White
Cab tire cord
P1
2
3
Yellow
1
Connector at closed end
P2
5
4
Black
Red
Switch
Controller
Black
Circuit drawing
<Low pressure specifications>
115V area
The condenser is not used in some areas.
Cab tire cord
P1
2
3
Yellow
Connector at closed end
1
Orange color
Orange color
White
P2
4
5
Connector at closed end
Red
Black
Switch
Black
Capasitor
Controller
<High pressure specifications>
Field without chalk coil
capacitor are not used in some areas.
Line filter
Cab tire cord
P1
3
2
Yellow
Connector at closed end
1
Orange color
P2
4
5
Orange color
Connector at closed end
Red
Black
Switch
Black
Connector at
closed end
White
Brake switch
COM
Capasitor
Controller
NC
White
Violet
Connector at closed end
Orange color
Chalk coil
Capasitor
Field with chalk
Cab tire cord
P1
3
2
Yellow
Connector at closed end
1
Orange color
P2
5
4
Switch
Red
Orange color
Connector at closed end
Black
Black
Brake switch
COM
Capasitor
Controller
NC
Connector at
closed end
White
White
Violet
Connector at closed end
Orange color
Chalk coil
Capasitor