yeti asrc owner`s manual

YETI ASRC
OWNER’S MANUAL
YETI CYCLES
621 Corporate Circle, Unit B
Golden, CO 80401
888.576.9384
www.yeticycles.com
TABLE OF CONTENTS
BRAND OVERVIEW
06
FRAME FEATURES
08
GEOMETRY
10
MAINTENANCE SCHEDULE
12
SETUP
SHOCK SETUP
14
QUICK START GUIDE
16
CABLE/LINE SETUP
18
TECHNICAL
ASSEMBLY OVERVIEW
20
EXPLODED VIEWS
28
REBUILD KITS
31
LEGAL
4.
WARRANTY
34
CONTACT INFORMATION
35
5.
WELCOME TO THE TRIBE.
CONGRATULATIONS ON YOUR
PURCHASE OF A NEW YETI.
We are confident your new bicycle will exceed
your expectations for value, performance, and
ride quality. Each frameset and component
has been custom specified and designed to
enhance your riding experience. Whether you
are a beginner cyclist, or a seasoned pro,
your Yeti bicycle will provide endless hours of
two-wheeled fun.
This manual outlines basic setup and
maintenance recommendations of your new
Yeti. Because it is impossible to anticipate
every situation or condition that may occur
during the assembly, setup, and maintenance
of your bicycle, Yeti recommends that all
service and repairs be performed by your
local authorized Yeti Dealer.
This model specific manual is designed to
be used in conjunction with the general Yeti
Owner’s Manual and the manuals supplied by
the suspension manufactures. If you did not
receive the Yeti owner’s manual or the manual
provided by the suspension manufacturer
download the materials off the Internet, or
contact your local dealer.
This manual contains many “Warnings” and
“Cautions” concerning the consequences
of failure to maintain or inspect your bicycle.
The word “Warning” indicates a potentially
hazardous situation in which , if not avoided,
could result in serious injury or death. The
word “Caution” indicates a potentially
hazardous situation in which, if not avoided
may result in minor injuries or damage to
your bicycle or a component of your bicycle.
Be sure to read and understand all of the
Warnings and Cautions listed in the manual. Bicycling can be a hazardous activity
even under the best of circumstances.
Proper maintenance of your bicycle is your
responsibility and when done properly helps
reduce the risk of injury and damage to your
bicycle.
Warning: Make sure you review and understand the warnings, instructions, and content of this manual and accompanying
manuals for your bicycle. Warning: Technological advances have made bicycles and bicycle components more complex and the pace of innovation is
increasing. It is impossible for this manual or the accompanying manuals to provide all the information required to properly
repair and/or maintain your bicycle. In order to help minimize the chances of an injury, it is critical for you to have work
performed by an authorized Yeti retailer.
6.
7.
OUR NEW ASR-C IS A
CROSS-COUNTRY RACE
MACHINE WITH AN
ENDURO ALTER-EGO.
8.
1.
HIGH MODULUS CARBON CONSTRUCTION
2.
SIGNATURE YETI “LOOPSTAYS”
3.
CARBON LINK
4.
OVERSIZED PIVOT PINS WITH ENDURO MAX BEARINGS
5.
TAPERED INSET HEADTUBE (44MM/56MM)
6.
CUSTOM CHAIN-SLAP GUARDS
7.
CUSTOM DOWNTUBE GUARD
8.
CABLE ROUTING FOR INTERNALLY ROUTED HEIGHT ADJUSTABLE SEAT POST
9.
DIRECT MOUNT FRONT DERAILLEUR
10.
INTERNAL SHIFTER AND BRAKE ROUTING
11.
TWO WATER BOTTLE MOUNTS
12.
27.5” WHEELS ON XS, SM / 29” WHEELS ON MD, LG AND XL
1.
Yeti’s custom high modulus carbon construction offers unparalleled
stiffness and ride quality. It also offers best in category frame
weight.
2.
Distinctive and functional Loopstays provide unparalleled ride
quality and stiffness.
3.
Full carbon linkage reduces weight and increases stiffness. Plus it
looks pretty sweet too!
4.
All pivots on the ASR-C are oversized and use custom Endure Max
bearings for smooth suspension and maximum wear life.
5.
Our tapered inset head tube creates a stiff front end for superior
handling as well as a wide range of compatibility with forks and
headsets.
6.
With all of our bikes we make custom frame protectors, the ASR-C
is no exception.
7.
Custom molded down tube protector keeps the frame looking
fresher longer and protects against the inevitable rock impacts.
8.
This may be an “XC” bike, but it has the soul of an enduro machine.
We know you’ll be riding it with a dropper post.
9.
The direct mount front derailleur allows for simple, light and precise
front shifting.
10.
Internally routed shift cable routing keeps the cables clean and
keeps the bike’s lines clean too.
11.
The ASR-C is still an “XC” rig, so we included 2 water bottle
mounting locations.
12.
We size the wheels to fit the rider, not the conventions. XS and SM
frames use 27.5 wheels to keep the rider on the bike, not in it.
9.
GEOMETRY
FOX 32 / 120MM FORK
I
L
J
A
D
C
K
E
XS
SM
MD
LG
XL
A
15.0
16.5
17.5
19.0
20.5
B
21.7
22.7
23.7
25.7
25.7
C
68.0
68.0
69.1
69.1
69.1
D
72.0
72.0
72.0
72.0
72.0
E
17.3
17.3
17.5
17.5
17.5
F
42.2
43.3
44.5
45.5
46.5
G
13.0
13.0
13.0
13.0
13.0
H
28.7
28.7
28.7
28.8
28.9
I
4.2
4.8
3.5
4.4
5.2
J
20.0
20.0
20.5
20.5
20.5
K
1.73
1.73
1.73
1.73
1.73
L
22.6
23.2
23.4
24.2
25.0
M
14.2
15.0
16.7
17.4
18.2
WHL
27.5
27.5
29.0
29.0
29.0
M
B
G
F
H
*All measurements are in inches
FIT
10.
X-SMALL
4’11” (150 CM) - 5’3” (160 CM)
SMALL
5'3" (160 CM) - 5'7" (170 CM)
MEDIUM
5'7" (170 CM) - 5'11" (180 CM)
LARGE
5'11" (180 CM) - 6'3" (191 CM)
X-LARGE
6'3" (191 CM) - 6'6" (198 CM)
11.
KEEP YOUR YETI FRESH
AND CLEAN
SCHEDULE
CLEAN AND LUBE CHAIN
CHECK TIRE PRESSURE
CLEAN BIKE OF MUD AND DEBRIS
ANNUALLY
Yeti recommends using a torque wrench when assembling your frame. Torque specifications
for individual parts on the ASR-C are listed below, as well as in the step by step assembly
instructions later in the manual. For general bicycle maintenance please consult the torque
specifications of the manufacture’s component you are adjusting.
3 MONTHS
Following these guidelines will help maintain the performance of your bicycle and prevent
more serious problems from arising. It is important to remember that service intervals can vary
depending on climate, trail conditions and riding frequency. If you are unsure about working on
your own bicycle, contact your authorized Yeti Dealer or visit the repair help section at www.
parktool.com for more information on general bicycle maintenance.
MONTHLY
TORQUE
WEEKLY
OVERVIEW
KEY TORQUE SPECS
PART NUMBER
DESCRIPTION
TORQUE (NM)
300030150
UPPER LINK PIVOT
5NM
300030154
LOWER LINK PIVOT
6.5NM
300030249
FRONT SHOCK MOUNT
6.5NM
300020047
MAIN PIVOT AXLE
9NM
300040454
MAIN PIVOT COLLET
13.5NM
CHECK BRAKE FUNCTION
CHECK SHOCK PRESSURE, IF APPLICABLE
CHECK FOR LOOSE BOLTS AND TIGHTEN, IF NECESSARY
CHECK HEADSET AND TIGHTEN / LOOSEN, IF NECESSARY
THOROUGHLY CLEAN PIVOT POINTS WITH A RAG (DO NOT LUBRICATE)
REPLACE BRAKE PADS, IF NECESSARY
CHECK TIRES FOR WEAR
CHECK SPOKE TENSION, RETENTION IF NECESSARY
CHECK CHAIN FOR WEAR AND REPLACE IF NECESSARY
COMPLETE TUNE-UP PERFORMED BY AN AUTHORIZED YETI DEALER
12.
13.
SHOCK SETUP
YETI TIPS
TOOLS NEEDED
Inspect your shock for any visible damage.
If oil is leaking or you notice any damage to
the surfaces or seals, please contact the Fox
Racing Shox service center for repair at 800.
FOX.SHOX.
•Shock Pump
•Tape Measure
Shock set-up can fluctuate greatly based on
the rider. The set-up guide is intended as a
base line to get the rider started. Experiment
with your settings to find the set-up that
works best for you.
01. AIR PRESSURE
02. SAG
The main air spring controls the sag of the shock.
For the ASR-C to ride properly it is important to
setup the shock with the correct amount of sag.
For general riding the ASR-C works best with 2530% or 11mm of shock sag. To increase the sag
reduce the main spring air pressure. To reduce
the sag increase the main spring air pressure.
Once you have set your baseline air pressure you
need to measure the sag. To measure the sag
slide the travel indicator (O-Ring) up against the
shock body. With a friend supporting the bike,
sit on the saddle (do not bounce) and allow your
body weight to compress the shock. Once you
have compressed the shock, get off the bike
and measure the distance between the shock
body and the new position of the travel indicator
(O-Ring). This is your sag.
03. REBOUND
The rebound adjustment has 14 clicks of adjustment. The rebound knob is the red adjustment dial located
above the blue compression damping adjustment lever. As a general rule, adjustments that are too fast
(counter-clockwise adjustment) will produce a springy ride with excessive kick-up of the rear end causing
a bucking sensation. Adjustments that are too slow (clockwise adjustment) will cause packing of the rear
wheel indicated by a sluggish ride feeling ride.
Slower rebound- turn the knob clockwise
Faster rebound- turn the knob counter-clockwise
14.
15.
SHOCK SETUP
04. COMPRESSION DAMPING
05. TRAIL ADJUST
The compression damping has three levels of
adjustment and is controlled by the blue lever
on the shock. The “climb” mode engages the
firmest low-speed compression setting for
maximum pedaling efficiency. The “trail” mode
engages a moderate low-speed compression
setting for an optimal blend of pedaling efficiency
and bike control, on various riding terrain.
Finally, the “descend” mode sets the low-speed
compression setting to fully open, for maximum
bike control and shock absorbency on steep,
aggressive descents.
The trail adjust dial controls the “trail” mode low
speed compression adjustment. It has three
levels of adjustment and is controlled by the
black dial on the shock body. Turning the dial
clockwise increases low speed compression
damping, making the shock feel stiffer under low
speed compressions. Turning the dial counterclockwise will decrease low speed compression
damping, making the shock feel softer under low
speed compressions. Please note this adjustment
only affects the shock performance while riding in
“trail” mode.
QUICK START GUIDE - CTD ADJUST
ADJUSTMENT
SETTING
AIR SPRING SETTING (PSI)
RIDER WEIGHT LESS 10 PSI
MEASURED SAG (MM)
11MM
REBOUND
*5 CLICKS
COMPRESSION DAMPING
BASED ON TERRAIN
TRAIL ADJUST
POSITION 2
*All clicks are counted clockwise, rotating from the all the
way out or counter - clockwise dial position.
16.
17.
CABLE SETUP
YETI TIPS
The ASR-C uses internal routing for the derailleurs. By using internal routing we have eliminated
exposure and cleaned up the look. This also reduces the entrance of unwanted elements such
as sweat and sediment into your shifting system. Use of internal cable routing will leave the
bike looking clean and keep your shifting smoother for a longer period of time.
Caution: The failure to properly route shifter housing can cause malfunction and unexpected shifting.
03. REAR DERAILLEUR
Measure the appropriate amount of shifter housing. There are going to be two segments; one from the
handlebar to the top housing stop port and one from the bottom housing stop port to the rear derailleur.
From the shifter, run the housing parallel to the brake line around the head tube to the upper port on the
non drive side of the down tube. Thread the cable through the down tube to the lower port just above the
BB. Removing the lower housing stop port will make this easy. Thread the cable through the non drive
side of the housing stop and re install. Thread the cable through the 2nd housing segment and route the
housing along the underside of the drive side chain stay. Follow the housing guides to the derailleur, leaving
enough slack to allow for suspension movement. Adjust your derailleur according to the manufacturers
specifications. Note: You may want to route the front shift cable at the same time for easiest installation.
01. INTERNALLY ROUTED DROPPER POST
From the handle bar lever, your internally routed
seat post line will parallel the rear brake line
down the down tube. Curve the line around the
bottom of the bottom bracket and up to the port
on the back of the seat tube. The line should
pass between the chain stay bridge and the front
triangle. Each seat post is different, please follow
the instructions from the manufacturer of your
seat post for full installation procedure.
04. FRONT DERAILLEUR
02. REAR BRAKE
From the handlebar, the rear brake line is routed around the non drive side of the head tube. There are zip tie
cable housing guides down the down tube from there to the bottom bracket. Loosely zip tie the housing to
each guide to allow for adjustment. Follow the housing guides under the BB to the non drive side chain stay
leaving enough slack to allow for suspension movement. The housing should be routed on the inside of the
chain stay to the caliper. Once everything is in place tighten your zip ties all the way.
18.
Measure the appropriate amount of shifter housing. There are going to be two segments; one from the
handlebar to the top housing stop port and one from the bottom housing stop port to the front derailleur.
From the shifter, run the housing around the head tube to the upper housing stop port on the drive side of
the down tube. Thread the cable through the down tube to the lower port just above the BB. Removing the
lower housing stop port will make this easy. Thread the cable through the drive side of the housing stop and
re install. From the lower housing stop port there is a short segment of housing to the stop on the back of
the BB. Make sure there is a gentle curve in that segment to allow for smooth shifting. From there route the
bare cable to your front derailleur and set up according to manufacturer specifications.
19.
ASSEMBLY
YETI TIPS
TOOLS NEEDED
Make sure your tools are in good condition.
A worn allen key can round the hex on a bolt
not allowing for proper torque.
•Dead blow hammer
•Two - 5mm allen keys
•10mm allen key
•Guide pin tool
•Grease
•Blue Loctite (248)
•Pink Loctite (222)
Torque settings are listed throughout the
instructions. It is import to properly prep all
bolt threads. The instructions denote whether
to use a Loctite compound or grease.
01.
02.
Find and place the upper link spacers while
holding the link.
While holding the upper link spacers slide the
link in place. Have a Fox guide pin easy to reach
before you do this. Slide the guide pin through
the link, spacers and frame to hold everything in
place.
03.
04.
Using the Fox guide pin, insert the female upper
link pivot pin. Remove the guide pin and place in
an easy to reach place.
Prep male bolt with blue (248) Loctite.
Warning: Service on Yeti bicycles requires special knowledge
and tools. Yeti Cycles recommends that all service and
repairs be performed by an authorized Yeti Dealer
20.
21.
ASSEMBLY
ASSEMBLY
05.
06.
09.
10.
Loosely thread the male bolt into the upper link
pivot pin on the frame. Do not overtighten.
Finish tightening the upper link pivot using a well
calibrated torque wrench set to 5 Nm
Slide the main pivot axle into the swingarm
through the non drive side. Using a Fox guide pin
to align the pivot sleeve slide the main pivot axle
through until it contacts the threads
Thread the main pivot axle in using a 10mm allen
wrench and torque to 9 Nm.
Torque to 5 Nm
22.
Torque to 9 Nm
07.
08.
11.
12.
Prep the main pivot axle with grease.
Slide the swing arm into place over the main pivot
sleeve on the front triangle.
Prep the lower link shock spacers with a small
amount of grease. This will help them stay in
place on the link.
Place the shock spacing washers against the
bearings on the inside of the link using the grease
to hold them in place.
23.
ASSEMBLY
24.
ASSEMBLY
13.
14.
17.
18.
Use a Fox guide pin to align the link, spacers and
the swingarm.
Slip the front shock mount into the front triangle
and use another Fox guide pin to align and hold
it in place.
Using the guide pin slide the front shock
mounting hardware through the frame and shock.
Use a soft mallet to tap it through if necessary.
Apply blue (248) Loctite to the male bolts for the
shock mount and the lower link pivot at this time.
15.
16.
19.
20.
pull the lower link guide pin back, leaving it
partially in place. Give yourself clearance for the
rear of the shock to slide into place. Place the
shock into the link and reinsert the guide pin.
Using the guide pin, slide the lower link pivot
hardware through the swingarm, link and shock.
Use a soft mallet to tap it through if necessary.
Using a well calibrated torque, wrench tighten the
lower link hardware to 6.5 Nm.
Using a well calibrated torque, wrench tighten the
front shock mounting hardware to 6.5 Nm.
Torque to 6.5 Nm
Torque to 6.5 Nm
25.
ASSEMBLY
21.
22.
Prep your collet bolt with grease.
Thread the collet bolt into the main pivot axle.
Using a well calibrated torque wrench, torque to
13.5 Nm.
Torque to 13.5 Nm
23.
The completed ASR-Carbon frame. Now put
some parts on it and go for a ride!
26.
27.
EXPLODED VIEW
30
29
21
20
18
21
GREASE
2
1
25
19
9
8
8
LOCTITE
21
9
19
21
24
29
30
26
3
31
30
29
29
14
23
31
28
22
222
31
27
12
11
4
16
5
4
28.
11 13
11
11
15
17
10
12
6
13
7
29.
EXPLODED VIEW PARTS LIST
ITEM#
PART #
1
N/A
2
QTY
ITEM#
PART #
ASR-C FRONT TRIANGLE
1
26
300030288
STUD YETI TI FEMALE 8.0OD X 54MM, M6
1
300070006
ICE AXE HEAD BADGE
1
27
300030150
BOLT YETI TI FEMALE 8.0OD X 36.5MM, M6
1
3
300060072
YETI SEAT CLAMP STANDARD
1
28
300030249
BOLT YETI TI FEMALE 8.0OD X 31.5MM, M6
1
4
300020045
BEARING F6902 2RS-MAX 28X15X7 2P5-OUT
2
29
300030151
BOLT TI MALE M6X12.0MM
4
5
300030272
SPACER 15MM X 23.75MM
1
30
300030062
WASHER 6.5X12.5X0.5 MM
3
6
300040442
PORT STOP, DOWN TUBE LOWER
1
31
300030069
WASHER 8.8X12.5X0.5 MM
3
7
300030244
BOLT BUTTON HEAD (M3X0.5X8)
1
8
300040441
PORT STOP, DOWN TUBE UPPER
2
9
300030215
BOLT FLAT HEAD (M3X0.5X8)
2
10
400100107
PROTECTOR ASR-C DOWN TUBE
1
11
300030148
WASHER 5.1X8.9X1MM
4
12
300030010
BOLT-CAP H20 (M5 X 0.8 X 16MM)
2
13
300030119
SCREW CAP (M5X0P8X10)
2
14
N/A
ASR-C REAR TRIANGLE
1
15
400100108
CHAIN STAY PROTECTOR ASR-C 29
1
400100117
CHAIN STAY PROTECTOR ASR-C 27.5
1
400100109
SEAT STAY PROTECTOR ASR-C 29
1
400100118
SEAT STAY PROTECTOR ASR-C 27.5
1
17
300060070
12X142 HANGER STD KIT
1
18
N/A
FOX FLOAT CTD 6.5X1.5
1
19
214-09-006
FOX MOUNT KIT 21.84MM (22MM)
2
20
200020203
ASR-C LINK
1
21
300020048
BEARING 608-SRS-MAX 22X8X7 1-IN
4
22
300040457
COLLET_AXLE_15X51.5SX12.0T_M15X1.5
1
23
300040454
COLLET-WEDGE ASSEMBLY
1
24
300020047
SHOCK SPACER 4.5MM
2
25
300040451
INNER RACE EXTENDER
2
16
30.
DESCRIPTION
DESCRIPTION
QTY
REBUILD KITS
PART #
DESCRIPTION
200020220
LINK ASR-C W/BEARING
200020225
ASR-C CABLE GUIDE KIT
QTY
1
300030215
M3X.5X8 FLAT HEAD BOLT
1
300030244
M3X.5X8 BUTTON HEAD BOLT
2
300040441
PORT STOP DT UPPER
1
300040442
PORT STOP DT LOWER
2
31.
REBUILD KITS CONTINUED
PART #
DESCRIPTION
200020222
ASR-C MASTER REBUILD KIT
PART #
DESCRIPTION
200020223
ASR-C HARDWARE KIT
QTY
300020045
BEARING F6902 2RS 28X15X7 OUT
2
300020047
SPACER 8MM X 4.5MM FOR SHOCK
2
300020047
SPACER 8MM X 4.5MM FOR SHOCK
2
300030062
WASHER SS 6.5MM ID 12.5 OD .5M
3
300020048
BEARING 608 FE 2RS
4
300030069
WASHER SS 8.8MM ID 12.5MM OD .
3
300030062
WASHER SS 6.5MM ID 12.5 OD .5M
3
300030150
BOLT-TI-FEMALE 8.0X36.5MM
1
300030069
WASHER SS 8.8MM ID 12.5MM OD
3
300030151
BOLT-TI-MALE M6X12MM
4
300030150
BOLT-TI-FEMALE 8.0X36.5MM
1
300030154
STUD-TI-FEMALE 8X54.5MM
1
300030151
BOLT-TI-MALE M6X12MM
4
300030215
M3X.5X8 FLAT HEAD BOLT
2
300030154
STUD-TI-FEMALE 8X54.5MM
1
300030244
M3X.5X8 BUTTON HEAD BOLT
1
300030215
M3X.5X8 FLAT HEAD BOLT
2
300030249
BOLT-TI-FEMALE 8.0OD M6X31.5M
1
300030244
M3X.5X8 BUTTON HEAD BOLT
1
300040441
PORT STOP DT UPPER
2
300030249
BOLT-TI-FEMALE 8.0OD M6X31.5M
1
300040442
PORT STOP DT LOWER
1
300030272
SPACER 15X23.75MM
1
300040451
INNER RACE EXTENDER ASR-4C
2
300040441
PORT STOP DT UPPER
2
300040454
COLLET-WEDGE ASSEMBLY GEN2
1
300040442
PORT STOP DT LOWER
1
300040457
AXLE COLLET 15X51.5SX12.0T
1
300040451
INNER RACE EXTENDER ASR-4C
2
300040454
COLLET-WEDGE ASSEMBLY GEN2
1
400100123
300040457
AXLE COLLET 15X51.5SX12.0T
1
400100107
PROTECTOR DOWN TUBE ASR-C
1
400100108
PROTECTOR SEAT STAY ASR-C 29
1
400100109
PROTECTOR CHAIN STAY ASR-C 29
1
200020224
32.
QTY
ASR-C BEARING REBUILD KIT
ASR-C PROTECTOR KIT 29ER
300020045
BEARING F6902 2RS 28X15X7 OUT
2
300020048
BEARING 608 FE 2RS
4
400100123
300030272
SPACER 15X23.75MM
1
400100107
PROTECTOR DOWN TUBE ASR-C
1
400100117
PROTECTOR SEAT STAY ASR-C 27
1
400100118
PROTECTOR CHAIN STAY ASR-C 27
1
ASR-C PROTECTOR KIT 27.5
33.
WARRANTY
YETI LIMITED (5) FIVE YEAR FRAME WARRANTY
(applies to SB5c / SB6c / ASR-4 / 575 / ARC-C)
Yeti Cycles will repair or replace, at its option, any of the above listed frames it determines to
be defective due to defective materials and/or workmanship. The (5) five year limited warranty
is conditioned upon the bicycle being ridden under normal conditions and having been
properly maintained. This warranty does not apply to the components attached to the frameset
such as suspension components, wheels, drive train, brakes, seat post, handlebar and stem.
This warranty applies only to the original owner and is non-transferable. This warranty is void if
the bicycle was not properly assembled by an authorized Yeti dealer.
ADDITIONAL CONDITIONS
These limited warranties do not apply to normal wear and tear, nor to claimed defects,
malfunctions or failures that result from abuse, neglect, improper assembly, improper
maintenance, alteration, collision, crash or misuse. The original owner shall pay all labor
charges connected with the repair or removal of all components. Under no circumstance does
this limited warranty include the cost of travel or shipment to and from an authorized Yeti
dealer. In order to exercise your rights under these limited warranties, the bicycle or frameset
must be presented to an authorized Yeti dealer, together with proof of purchase.
in the form of cracks, fracture lines, deformation, dents, and any other visual indicators of
abnormality. These safety checks for frame stress are important to prevent accidents, injury to
the cyclist, and product failure of a YETI frameset.
DISCLAIMER
YETI Cycles is not responsible for any damages to you or others arising from riding,
transporting or other use of your bicycle. In the event that your frame breaks or malfunctions,
YETI Cycles shall have no liability or obligation beyond the repair or replacement of your frame
pursuant to the terms outlined in the warranty.
*If you have a warranty concern, please contact your authorized Yeti dealer.
*The above warranties have been in effect since January 2012. For warranty information on Yeti
frames sold prior to that date please consult your local authorized dealer.
NO FAULT REPLACEMENT POLICY
Yeti Cycles will make replacement parts available at a minimum charge to the original owner
in the event of a crash or any other non-warranty situation. Yeti Cycles does this at its sole
discretion and reserves the right to refuse this offer.
PRODUCT LIFE CYCLE
Every YETI frameset has a useful product life cycle. The length of that useful product life
cycle will vary depending on the construction and the materials of the frameset, maintenance
and care the frameset receives , and the amount and type of use the frameset is subjected to
over its life. YETI recommends that an authorized YETI dealer should inspect the frame for
stress annually. Frame stress could cause potential failure and the signs are usually apparent
34.
YETI CYCLES
621 Corporate Circle, Unit B
Golden, CO 80401
(p) 303-278-6909
(f) 303-278-6906
www.yeticycles.com
BUSINESS HOURS
Monday-Friday
8AM-11:30AM, 1:00PM-5:30PM
(Mountain Time)