RE304 DSC®-Compatible Driveway Sensor

Performance Effects:
Increased Response
Decreased Response
Close to vehicle
Far from vehicle
Higher (door handle level)
Ground level
Slow vehicle
Fast vehicle
Large metal vehicle
Small vehicle with lots of plastic
Jumper on High Sensitivity
Jumper on Low Sensitivity
Generally, it shouldn’t matter which direction the sensor
head is rotated. But turning it 90 degrees may cause some
performance change +/-.
RE304 DSC®-Compatible Driveway Sensor
Features
• For sensing Vehicles passing by.
• Sensor continuously monitors earth’s magnetic field. When the large
metal mass of a vehicle drives by, the earth’s magnetic field is twisted.
The sensor then transmits a signal wirelessly to the control panel.
• Immune to pets, wildlife, leaves, dust, sunlight.
• NO DIGGING!
• Weatherproof design handles all environments.
• Strong, reliable RF signal.
• 3-5 year battery life on C battery.
• Low Battery indication.
Specifications
Vehicle sense distance:
0 – 15 feet
Lockout time after sensing a vehicle: 30 seconds
Mounting hardware:
post flange or ground stake
Replacement Battery:
Energizer C-Cell (better than Panasonic)
Temperature Range:
0F to 120F
[Note: high temperatures and high humidity can have a
significant effect on alkaline battery performance.]
Housing dimensions:
5.1 x 3.8 inches
Jumper on
Short Catch Radius
Specifications subject to change without notice.
(Low Sensitivity)
Key Instructions
• Battery “+” face away from springs. Secure batteries with binder.
• Do not plug drain & air holes. Do not overtighten top.
• Enrolling:
Put panel in Wireless Enrollment Mode.
Disconnect and then connect sensor battery. Special transmission
occurs on power-up, so that sensor enrolls.
Confirm ESN, Enter Zone # and Zone Type on DSC Panel
May also be enrolled via entering ESN.
Use in “Chime” Group, not an Alarm Group.
Supervision by panel is optional.
• Locating Sensor:
DEVICE LOCKS OUT FOR 30 SECONDS AFTER EACH SENSING EVENT.
So wait for 40 seconds to test each time.
1. Test max wireless range to panel, then install at no more than 2/3
of that limit.
2. Locate sensor close enough to driveway so that Short or Medium
Catch Radius can be used. Generally, mount sensor within 12 feet
of target vehicle. Mount more than 24 feet from street.
3. Mount on a SOLID POST (the plastic pipe is not recommended), about
door-handle height, so wind cannot make it sway and false chime.
Exploded Picture
Do not pull
antenna
Push battery down
towards spring, and
release to cause
enrollment
transmission
Jumper on Medium Catch Radius
Batteries secured
by binder
Jumper on Extended Catch Radius
(High Sensitivity)
Extended Catch Radius
(more likely to false chime)
O
Magnetic
sensor
Medium Catch Radius
Wireless
Range Limit
Short Catch Radius
(more likely to miss car)
Mount sensor on
sturdy post
Door-handle height
Page 1 of 3
Control
Panel
Install at no more than
2/3 of wireless limit
www.ResolutionProducts.com
24-Hour Tech Support Line: (715)808-0164
RE304_DSC-Compat_Driveway_Instructions
13-Jan-14
Page 2 of 3
www.ResolutionProducts.com
24-Hour Tech Support Line: (715)808-0164
RE304_DSC-Compat_Driveway_Instructions
13-Jan-14
Notices
“GE”, “Honeywell”, “DSC” and “Napco” are trademarks owned by General Electric Company,
Honeywell International Inc., Tyco Safety Products Canada LTD, and NAPCO Security Systems,
Inc., respectively.
Resolution Products, Inc. products will function with one of either GE, Honeywell, DSC or
Napco systems. However, no Resolution product is produced by, endorsed by, nor is officially
associated with GE, Honeywell, DSC or Napco. Resolution recommends verifying proper
enrollment and operation, per control panel installation instructions, at installation.
Warranty
Resolution Products, Inc. will replace products that are defective in their first five (5) years.
FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
This device may not cause harmful interference.
This device must accept any interference that may be received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the Resolution Products, Inc. could
void the user's authority to operate this equipment.
FCC ID: U5X-RE304
IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1)l'appareil ne doit pas produire de brouillage, et
(2)l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
IC: 8310A-RE304
Page 3 of 3
www.ResolutionProducts.com
24-Hour Tech Support Line: (715)808-0164
RE304_DSC-Compat_Driveway_Instructions
13-Jan-14