Garage Door Remote Instructions

1. Look in JMA’s remote guide to view remote details and confirm if the remote is able to be copied.
You will need to take note if it is rolling code or fixed code
2. Push buttons 1 + 2 at the same
time on the M-FR1 remote until
M-FR1 Instructions
the red light flashes.
3. Wait for the red light to turn off,
then press the button on the
JMA M-FR1 remote that you wish
to copy the original remote to.
YES
1
YES
APRIMATIC TXM (No perso)
1
YES
AVIDSEN
1
NOT REQUIRED
BENINCA / ALLMATIC /
EUROPE AUTOMATISME
1
YES
*
YES
2 (1+PROGRAMMING BUTTON)
1
NO+
CARDIN S449 (FM)
1
YES
CELINSA
1
YES
Rolling code - will automatically
DEA
1
YES
copy all its buttons starting from
DITEC
1
NOT REQUIRED
DOORMATIC
1
YES
ECOSTAR
1
NO+
the button you select. i.e. if you
choose button 2, buttons 1,2,3
on original remote will be copied
Remotes must be on a
smooth, non-metalic surface.
copy.
switches to green, the code
2
APRIMATIC TR
CARDIN S435
4. Keeping the remote less than 1cm
5. Once the M-FR1 remote light
AERF
1
to be copied 1 at a time.
original remote which you wish to
QUICK ENROLLMENT
(See Point 8)
BFT
Fixed code - each button has
continue to hold the button on the
TRANSMISSIONS
REQUIRED IN COPY SEQUENCE
CAME ATO
to 2,3,4 on M-FR1 copy.
from the M-FR1 remote, push and
ROLLING CODE BRANDS
For remotes that stop transmitting
after a few seconds, release button
has been received and you can
then push and hold again. Repeat
release the button on the original.
until the JMA M-FR1 turns green.
6. If the M-FR1 remote light changes to red, it requires an extra transmission from the original remote
to be sent. If this happens repeat steps 3 to 6.
7. Once the M-FR1 remote light switches off, the copy sequence is complete.
ERREKA
2 (1+PROGRAMMING BUTTON)
FAAC (Only Master)
2 (1+PROGRAMMING BUTTON)
*
*
YES
YES
NOT REQUIRED
FADINI
1
GENIE
2
NO+
YES
GENIUS / ADYX
1
YES
GIBIDI
1
YES
JCM 1a GEN
2
YES
JCM 2a GEN
2
YES
KEY
2
NO+
LIFT MASTER / CHAMBERLAIN
1
NO+
MHOUSE
1
YES
MOTORLINE
1
NO+
MUTANCODE
2
YES
NICE FLOR (No perso)
1
YES
NORMSTHAL / CRAWFORD
1
NO+
NOVOFERM / TORMATIC
1
NO+
PRASTEL TP2E (No perso)
1
YES
PUJOL VARIO
1
YES
ROLLTORE TP2E (No perso)
1
YES
ROPER
2
NO+
SEAV
1
NO+
SKYMASTER
1
NO+
SMILO
1
YES
SOMFY KEYTIS / TELIS
1
NO+
SOMMER (FM)
1
NO+
TELCOMA FM 402 (FM)
2
YES
V2
1
NO+
* Programming Button - If required, you must locate the hidden
8. Quick Enrollment
Fixed code remotes do not require programming into the receiver. For rolling code remotes, see attached
table to check whether it can be quickly enrolled. If yes, push and hold the copied button for 14 seconds in
close proximity to the receiver (usually located next to the garage door, gate etc.)
programming button on the original remote.
More details on our website - sks.cx/mfr1
+ Manual Enrollment - If quick enrollment is not available, you must follow
the original manufacturers enrollment instructions.
Instructions Available at - sks.cx/mfr1