C.E. Tooling - Clark and Osborne

COLE ENGINEERED
C.E. TOOLING
Section
2
See Section 1 for Technical Information
THIN TURRET &
Strippit-Fab
ST&AS
Also STRIPPIT® 28ST Style Tools for FC1500
Table of Contents Version Dec-11
COLE ENGINEERED
THIN TURRET TOOLING: The original tool style was developed by Strippit®. A modified version was later introduced by
Amada. C.E. Tooling produces interchangeable tools and components for all major tooling variations. Basically all tool styles developed
for the small station (up to 1¼” punch size range) are universally compatible. It’s the larger 2” and 3 ½” stations that are not compatible. Examples
of turret differences: Strippit® Style 3 ½” dies are .85 thick where Amada style are 1.19 thick. Strippit® style Strippers are 4” Dia. where Amada
style are 3 ¾”. The Strippit® style 3 ½” punch has a ½” thread and a .25 dowel pin, where one of the Amada styles of 3 ½” punches, have M12
Strippit® is a Registered Trade Mark of tLVD Corporation, Inc. • Series 90® is a Registered Trade Mark of Wilson Tool International
Tools up to 1.250 (31,7mm) For use in all FAB & Thin Turret Mach.
1/2” Station DROP-IN TOOLS .031 - .500 ,8-12,7mm
5/8” Station DROP-IN TOOLS .031-.6251,8-15,8mm
COMPATIBLE COMPONENTS FOR ALL MAJOR BRANDS
COMPATIBLE COMPONENTS FOR ALL MAJOR BRANDS
1 1/4” Station ASSEMBLIES .500-1.250, 12,7-31,7MM
PAGE
Delivery
Work
Days
6 & 7 1-3
1-3
6
8-10 1-3
Tools from 1.251-5” (31,71-114,3mm)
FAB: Strippit® Style Turret 2” Station 1.251-2.000 37,8-50,8mm • 2”Square Universal Notching
®
FAB: Strippit Style Turret 3½” Station 1.251-3.500 (31,7-88,9mm)
FAB: Strippit® Style Multi-Tool 3, 8, & 30 compatible components
Thin Turret: Style Turret 2” Station 1.251-2.000 (37,8-50,8mm) • 2” Square Notching
Thin Turret Style Turret 3½” Station Guide Assemblies. AESI “OLD, & NEW” Styles
Station 1.251-3.500 (31,7-88,9mm) Tools for all major Holder Styles
Thin Turret Style 3½” Shearing Tools
Thin Turret 3½”
28ST Tools for Strippit® FC-1500 machines
2-4
14
15
15-17
1-4
17
request
5
23
4
4
5
Alignment Tools
CHARACTER MARKING UNITS
Corner Radius Tools
Ejectors
Punch Shears Punch Sharpening Fixture • •
Stripper Adhesive Disks
Trim & Part
Work Holder Parts
2-8
1
1
4
1
4
3-10
PROGRAMMING
19-23
See Section 1
Search Catalog for specific items with Ctrl-F
Page 2
1-3
section 14
SPECIAL APPLICATION FORMING TOOLS
Patented QUICK SET™ FORMING: SET UP
1-3
11
12-13 1-3
18 2-10
ADDITIONAL COSTS FOR NON-STANDARD OPTIONS
RADIUS
COLE
ENGINEERED
Add 25% to set
price for Clearance
of .003 (.08mm) &
Less.
RADIUS OR 45°°CHAMFERS + $ per corner
CHAMFER
PUNCHES
Corners 1-3 X #
With Length under 1.625 and any size Radius or Chamfer
# X $10.00
With Length over 1.625 & .032 maximum Radius or Chamfer
# X $10.00
With Length over 1.625 and Radius or Chamfer over .032(,8mm) # X $15.00
Add On To All DIES any size Radius or Chamfer
# X $10.00
No Extra Charge for STRIPPERS or When Ordered As A Set
4(all)
$10.00
$30.00
$40.00
$10.00
Widths or Dia. Under .093(2,36mm) Add 30% to set price.
Widths or Dia. Under .062(1,57mm) Add 50% to set price.
Widths or Dia. Under .046(1,2mm) Add 100% to set price.
Add 50% to die price
for Solid Dies.
.09 land,
then
1.5° relief
Optional
.09
STUBBY PUNCH
Included in add on cost; Dies are produced with .090 land then a 1.5° relief is given to prevent multiple slugs
from stacking causing excessive pressure on punch. Further, punches can be produced with Stubby Punch Design
at no additional charge. A Stubby Punch has it’s tip (diameter or width) first ground to a size of .187 then a tip is
DIA. OR
ground to requested size for a length of .225+ thickness to be punched. (If fitted strippers are used, + .125 to tip .187
Dia.
WIDTH
.156
grind length and use strippers .187 or > in diameter or width.)
or Width
STANDARD KEYING
10 Standard Shapes plus Rounds. (RT Rectangles • SQ=Square • OB=Obround • SD=Single-D • DD=Double-D
LD=Long-D • EQ=Equalateral • OC=Octagon • HX=Hexagon • QD-Quad-D • Add $10 per set to standard price for LD & EQ
LOOKING AT FACE OF
LOOKING AT TOP OF
PUNCH
DIE
Shapes on Angles or Extra Key
Locations. Die View
90
Angle
120
Ex. AT Sta.B
Keyed 20
Sta.
A&B
½ •1¼
20
180
0
Ex. 28XX/36tc
Ex.114/112/CM Keyed 20
Keyed 20
270
Sta. C
Visualize location key positioned as
tool would load into turret. Start with
2”
length of shape horizontal.(Length points to 0º)
Next Rotate shape, not location key.
A sketch accompanying your order insures
keying as required! Note: Other Manufactures
ordering diagrams may differ from C.E.’s!
Sta. D
3½”
10 STANDARD SHAPES
Ships in 1 - 4 work days.
RECTANGLE • SQUARE • OBROUND • SINGLE-D
DOUBLE-D • QUAD-D • HEXAGON • OCTAGON
+ $10 PER SET FOR: LONG-D & EQUILATERAL
Sta. E
4½”
Series
80
Expediting FDS=Firm Delivery Service
• Order by 1pm,
SPECIAL SHAPES
Tool Styles: AT, AS, ST:
1 day FDS=25% 2 day FDS=10%
Tool Styles 36tc, 28st, 92/93
1 day FDS=50% 2 day FDS=25%
Sta.C-E
2”-4½”
Expediting: 3 days 10%, 2
days 30%, 1 day 50%
Page 3
CE PRODUCT FEATURES HIGHLIGHTS
Character Markng
PUNCH FEATURES
COLE ENGINEERED
Accepts Replaceable Character Insert
Easier stripping and reduced gauling as we
extend 1/4°(1/8° per side) Back Taper
Cutting Edge and Corners .003 honed radius
Slug Ejectors
By default holes are placed in
punch tip sizes >.270”/6.86mm
EJECTOR Clover
For Hole Size
.078/2mm
.109/3mm
6mm-.25”
.394/10mm
.594/15mm
Square
Round
AT,AS,ST
4W,2W,2B
N/A
*AEJ-S3 24pc
*AEJ-S6 24pc
*AEJ-S10 24pc
*AEJ-S6 24pc
*AEJ-C3
*AEJ-C6
*AEJC10
*AEJ-R2 50pc
*AEJ-R7 50pc
Station Adaptors
STRIP GUARD Adhesive Disc
Stripper /
1/2
1-1/4
2”
3-1/2
4-1/2
Use 1-1/4” tools in
3-1/2” turret station.
Upper Guide Adapter
STE-STCGA / ASD-STCGA
Die Adapter
STE-STCDA / ASD-STCDA
Dia.
.87
1.75
3.67
4.67
Qty
10 Pcs
10 Pcs
10 Pcs
10 Pcs
10 Pcs
Part#
*A06082
*A06084
*A06085
*A06086
*A06088
Price
8.60
8.60
66.90
Reduces marring of material by the stripper. Just peel
off adhesive backing and attach to stripper face. Use
Dies Types: To allow the slug to fall through die land, a taper relief is given
to allow slug to pass though with little drag.
Standard Round Straight + Positive
Round Die
Standard
Option S/O
Slug Z Hugger
Option S/F
Slug Trap/Free
CORNER ROUNDING For Single Station Machines
RADIUS
Sta.
Cat. Code
UNDER 1/8
† 1/8-3/16-1/4-3/8-1/2
† 3/4, 7/8, 1”, 1½, 2”
1-1/4
1-1/4
3-1/2
*SSTCPADsprR
*SSTCPAD†rCR
*SSTEPDS†rCR
S/F
With Die
Gauge
Stocked dies for use with 22-7gauge material
No Die Gage
Punch w/heel
RADIUS
TRIM & PART / LATTICE Tools for Single Station Machines
RADIUS
UNDER 3/32
3/32, 1/8, 5/32, 3/16, 1/4, 5/16,
7/16, 1/2, 9/16, 5/8, 3/4
7/8, 1”, 1-1/4”, 1-1/2
Page 4
w/heel No Die Gauge
Sta. Punch
& Die Gauge Punch w/heel
1-1/4
1-1/4
3-1/2
3-1/2
OTHER RADII ALSO AVAILABLE ON A MADE-TO-ORDER BASIS! CALL FOR PRICING.
RADIUS
OPTIONAL PUNCH SHEARS
COLE ENGINEERED
Considered for All Diagonal Dimensions > 2”/50.8mm and a Min.Width of .375/9.53mm
Roof Top
*ART
Best all purpose
shear for reducing
tonnage.
Nibbling must be
performed at 75% of
punch size to avoid
side loading.
Concave
*ACS
Inverted
*AIS
Sq. & Rt Shown
An
all purpose
shear. Ideal for
nibbling.
Sq. & Rt Shown
An all purpose shear.
Ideal for nibbling.
ALIGNMENT TOOLS
Double
Inverted
*ADIS
Best Shear for
slotting tools, 3”
or longer in
length.
Whisper
Spiracle
*ASPS
(1-Way)
*AWS\
Reduces tonnage
while reducing
slug deformation.
Requires a very
Ridged Press.
Ideal for rounds or
squares < 1.18 30,m.
Lessons tool side
loading
“Easy to sharpen”!
Punch Sharpening Fixtures
Grind any type of shear safely, easily,and
with out damaging punch.
2" Punch
AESI New Style 3-1/2
Full Body Punch
For all Strippit®NC & SAF Machines
1-¼ Sta.
STC-ALIGN-PD
3-½” Sta.
STE-ALIGN-PD
STC-SETUP-r
1¼ Set-Up Plug
Thin Turret Style Turrets
1¼” Sta, B
STC-ALIGN-PD
2” Sta. C
ASC-ALIGN-PD
3½” Sta. D
ASD-ALIGN-PD
Strippit Style
3-1/2 Punch
Item No. *SSTPSF
For Machine Parts,
Go to Section 11 booklet for Amada
brand machines,
Section 11 for Amada
Section 12 for Di-Acro®,
Section 14 for Strippit® &
Page 5
DROP-IN Tools
1/2” & 5/8” Shank Punches
COLE ENGINEERED
1/2”Unit Range= .031-.500, .79-12,7mm
5/8”Unit Range= .031-.625, 79-15, 8mm
CLIP STYLE
SIDE LOAD
Side Load
Stripper
No clips or pliers
required. Simply lift
punch out and slide
stripper out.
C.E. Side Lock
Punch Heads
RETAINING CLIP
Pliers *APPLY
CE & Strippit®
1/2 or 5/8 Holder Side
Load
RETAINING CLIP
ASTAGC
CE Part#
A=½” or B = 5/8
ROUND SHAPE
*= R-round S-shape
ST-(A or B)-DIc-s
1/2 or 5/8 Holder Clip Style ST-(A or B)-GH-s
1/2 or 5/8 DROP-SET
Punch, Head, Fitted Stripper & Die
ST(AorB)PHSDc-*
+$6.25 for Side Lock P. Head
1/2 or 5/8 PUNCH
ST-(A or B)-P-*
1/2 or 5/8 Punch Head
ST-(A or B)-H
1/2 or 5/8 Punch Head Side Lock
ST-(A or B)-sl-H
STRIPPER PLATE (Fitted)
ST-(A or B)-Sc-*
STRIPPER PLATE Urethane
DIE
ST-(A or B)-Su-*
DIE w/Slug Trap™ S/F
ST-(A or B)-Dst-*
DIE w/Slug Z-Hugger S/O
ST-(A or B)-Dso-*
ST-(A or B)-D-*
WT Style
A=½” or B = 5/8
*= R-round S-shape
1/2 or 5/8 Holder Side Load
ST-(A or B)-DIw-s
1/2 or 5/8 Holder Clip Style
DROP-SET
Punch, Head, fitted Stripper & Die
PUNCH D2 steel
Punch Head =WT
Punch Head Side Lock
STRIPPER PLATE Fitted
DIE
DIE w/Slug Trap™ S/F
DIE w/Slug Z-Hugger S/O
Page 6
ST(A or B)-PHSD*-*
ST-(A or B)-P-*
ST-(A or B)-H
ST-(A or B)-s-H
ST-(A or B)-Sw-*
ST-(A or B)-D-*
ST-(A or B)-D-st-*
ST-(A or B)-D-so-*
Round
n/a
Shape
1/2” Shank Punches
Maximum material
1/4” 6,mm
Mild Steel
SnapSnap-A-Part Range 031031-.500
COLE ENGINEERED
/.79.79-12,7mm
Tru-Arc Pliers
*APLY
RETAINING
CLIP
ASTAGC
CE Part#
Wilson Compatible
Punch& Guide Assembly
STA-GAsa*
PUNCH w/Retaining Ring
STA-Psa-*
STRIPPER (fitted)
DIE w/Slug Z-Hugger S/O
Punch Head
SPRING Chrome Vanadium
Support Assembly
O-Ring for spring support
Punch Guide Body
Punch Retaining Ring
STA-Sw-*
Round Shape
ST-(A or B)-D
STA-Hsk
STC-S
STA-SAsa
STA-SAor
STA-Hsk
*ASTARCW
1/2 sta
1/2” Strippit® Style Split Keeper Range 031031-.500 / .79.79-12,7mm
Strippit® Compatible
1/2sk
Please state
Short or
Long pins
when
ordering
Note: Short
pin shown.
PUNCH ONLY
GUIDE ADAPTERS
PUNCH HEAD
SPRINGChrome Vanadium
Keeper Clips (Set of 2)
CE Code
*=R-round S-shape
Round Shaped
STA-Psk-*
*A93047-000 Short Pin
*A49299-000 Long Pin
STA-Hsk
STC-S
STC-KC
◄ Shown is
Long pin style Punch Guide
Adapter Strippit # 49299-000
1/2”Uni
1/2”UniUni-Guide Style Assembly Range .031.031-.500 (,79(,79-12,7mm)
UP Compatible
1/2up
RETAINING CLIP
ASTAGC
PUNCH
STRIPPER
Stripper Retainer
PUNCH HEAD
Spring Chrome Vanadium
CE Part#
*=R-round S-shape
Round
Shaped
STA-Pup-*
STA-Sw-*
*ASTCAGC
STA-Hsk
STCS
1/2” Sta.A Amada® STYLE Range .031.031-.500 (.79,15,8mm)
Amada
Compatible
M12 Threads
CE Part#
Description
*=R-round S-shape
PUNCH ASSEMBLY
PUNCH
Drop-Set Punch,Head,Stripper & Die
STRIPPER FITTED
GUIDE HOLDER
PUNCH HEAD
AS-A-PA-*
AS-A-P-*
ASAPHSDc*
ST-A-SC-*
ST-A-GH-*
AS-A-H
Round Shaped
RETAINING
CLIP
*ASTAG
Page 7
FAB Strippit Style of Thin Turret
COLE ENGINEERED
1-1/4 Station
Range .501-1.250”/12.7-31.7mm
INDUSTRY STANDARD ASSEMBLY
Strippit® or WT Style
6
1
3
4
7
CE Tool Part#
PRICE
PRICE
Punch Assembly
STCPA-*
DIE
ST-C-D-*
DIE w/Slug Trap™ S/F
ST-C-D-st-*
ST-C-D-so-*
DIE w/Slug Z-Hugger S/O
PUNCH
STC-P-*
PUNCH HEAD
ST-C-H
SPRING Chrome VanadiumSteel
STC-S
SPRING RETAINER
STC-SR
GUIDE ONLY(Fitted)
STCG-*
“OVERSIZED UNITS”
Exceed station maximum to
1.29” 32.77mm
Add On Charge will Apply
Punch +$75
Guide $25 Die $5.00
Wrench
*A-SPWR
No Go Gauge
*A67294 $47
QA Quick Adjust™ Preloaded spring Pack Fast tool length adjustment, no tools needed.
Increased Grind Life Up to .250"/6.35mm in .06"/1.52mm material.
Use with Industry Standard Punch & Guide.
Note: Round punches need to be pinned and require a shaped guide to accommodate pin in the punch.
1
2
Strippit® or WT Style
3
10
Punch Guide& QA
STCPGC-*
Punch & Guide Only
STC-PG-*
DIE
ST-C-D-*
DIE w/Slug Trap™ S/F
ST-C-D-st-*
ST-C-D-so-*
DIE w/Slug Z-Hugger S/O
PUNCH Shapes
STC-Phs-*
PUNCH Pinned Round STC-Phs-rpin
4
5
6
7
8
9
ROUNDS
Punch &
Guide are
keyed when
used with
QAAssembly
Page 8
CE Tool Part#
10 QA Spring Assembly
4
2
7
8
6
5
9
3
QA Driver
QA Head
QA Spring Support
QA Adjust Pins
QA Spring for Adjust
QA Sprg Support Plate
O-Ring Retainer SPRING
STCQSA
STCQSD
STCQSH
STCQSSS
STC10393
STC6601
STC10395
*ASTCOring
STC-S
Round Shaped
Quick-Series M90 & KW90ABS S90/HP Style
FAB WT S90/HP Style
COLE ENGINEERED
1-1/4 Station B
Range .501-1.250”/12.7-31.7mm
Descripion
CE Part#
Punch & Guide Assembly STC-Paw9-*
PUNCH
Guide
DIE
DIE w/SLUG TRAP™ S/F
Die W/SLUG HUGGER™ S/O
Die Shim 3pc .4, .8, 1.2
STC-D*
STC-D-st-*
ST-C-Dso-*
*ASTCDS
Awaiting
New
Picture
1¼ Driver Assembly
1¼ Punch Driver
COIL SPRING
PUNCH HEAD
SHSS M5X8 Cone Point w/nylon
O-Ring for Spring Support
Standard Spring Support Assembly
Punch Retaining Ring new design
Punch Index Pin for length adjust
Punch Felt Filter
Strip Guard Adhesive Disc 10pc
CE Part #
COMPONENT PARTS
1
2
3
4
5
6
7
1¼ Driver Assembly
1¼ Punch Driver
HEAVY DUTY SPRING Coil
Spring Support Assembly
O-Ring for Spring Support
Spring Retainer Assembly
Wire Ring Clip
Strip Guard Adhesive Disc 10pc
Price
STC10156
STC10141
STC-S
STC-H
STC6268
STC6562
STC10142
STC2803
STC6874
STC10155
*A06084
Description
C.E. Tool
Punch & Guide Assembly STC-PAwh-*
ATB-Pwh-*
PUNCH
STC-Gwh-*
Guide
STC-D*
DIE
STC-D-st-*
DIE w/SLUG TRAP™ S/F
Die W/SLUG HUGGER™ S/O
ST-C-Dso-*
Die Shim 3pc .4, .8, 1.2
*ASTCDS
HEAVY DUTY S90/HP Style
Maximum Material 3/8 Mild Steel
PRICE
STC-Pw9-*
STC-Gw9-*
COMPONENT PARTS
5
4
2
3
7
6
PRICE
PRICE
CE Part #
PRICE
Price
*A10055
*A10042
STC30
ST10047
STC10035
STC10043
STC10044
*A06084
Page 9
FAB or Thin Turret 1-1/4” Heavy Duty
COLE ENGINEERED
Range thru-1.250”/12.7-31.7mm † Rounds 1.001-1.25
<1” use Below H.D. Nibbler
Maximum Material
3/8 Mild Steel
Components compatible for use in C.E.& Strippit® Mfg. Units
PUNCH
HEAD
SPRING
RANGE
PUNCH HAS 1° BACK
TAPER For Easier
Stripping and reduced
gauling
SPRING
PUNCH ASSEMBLY
DIE
SUPPORT
WASHER
KEY
GUIDE (Open End)
C.E. CAT
CODE NO.
.375-1.250” 9,5-31,7MM
1.25øPUNCH BODY
Ref.
STRIPPIT®
*R=ROUNDS
*S=SHAPE
NO.
PRICE
ROUND
STC-PAHM-* 200231
STC-D-*
D2 Steel
Ref.
STRIPPIT®
NO.
200242
48532
STC-D-st-* 200538-
200537
DIE 1/2-Solid w//Slug Trap STC-D-hdst-* 200538
200537
PUNCH
STC-PHM-* 200233-
200244
STC-GHD-s 200243
102.75
DIE w/Slug Trap™ S/F
GUIDE
High Speed Steel
Keyed 1.25 Open End
PRICE
SHAPE
† Rounds 1.001—1.250 Only <1” use Below H.D. Nibbling Tools
COMPONENT PARTS listed at bottom of page.
1 1/4” H.D. NIBBLING TOOLS High Speed Steel
Available Sizes through 1.000 or 25.4mm
PUNCH HEAD
SPRING
ROUNDS
CODE No.
1”PUNCH BODY
OIL RESERVOIR
Fill with 80/90 wt. oil
PUNCH HAS 1° BACK TAPER
Easier Stripping, and
Reduced gauling
Component Parts for Heavy Duty or Nibbling Units
ADJUSTABLE PUNCH HEAD
SPRING (STEEL) HEAVY DUTY
SHARPENING SHIM
LOCATION KEY (shaped guides)
WASHER
PUNCH LOCK
OIL RESERVOIR
Page 10
CODE.
PUNCH ASSEMBLY
STC-PANBr
200234-000
D2 Steel
STC-D-R
48532-000
DIE w/Slug Trap™ S/F
ST-C-D-st-*
DIE w/Slug Z-Hugger S/O
ST-C-D-so-*
PUNCH ONLY M2 STEEL
STC-PNB-R
200236-000
GUIDE Round 1” Open End
STC-GNB-R
200235-000
DIE
GUIDE Open Face
Ref.
STRIPPIT®
Part #
STC-PHHD
STC-SSHD
STC-SM
STC-GKHD
STC-WHD
STC-PL
STC-ORHD
STRIPPIT® CODE
200237-000
41706-000
200241-200
200245-000
200282-000
200238-000
200463-000
.
PRICE
PRICE
ROUND
FAB (Strippit) 3 1/2” Station Tools
COLE ENGINEERED
Notcher Punch shown in Standard
Guide Assembly.
Extended Life Punch has Sq. for full 1”
length and Double Concave Shear, plus
5-1/4” Ejectors
Metal Slip Fit Stripper,
®
Strippit
WT Compatible
DESCRIPTION
Notcher PUNCH
Notcher Stripper
C.E. Part#
STEPNT-s
STESNT-s
WT Part#
00449
00367
2”& 50mm Square Strippit Universal Notcher
®
Strippit Compatible
Save! 25% when
you buy 3 or more GUIDE ASSEMBLY
punches
For Fabri-Centers: 75/ 30,
750, 1000, 30/30; Cap 1000, 40/30, 1250/30; TSAF and 1250/45 machines Strippit Ref. No.
55665-200
CE Part#
STRIPPIT®
INCLUDES PUNCH
STEUNASSY
8665-200
PUNCH D2 Tool Steel
STEUNPS-s
86670-200
STEUNG-s
86667-200
STEUNSPRG
STED-s
STED-st-s
STEUNPD
STEUNR1
STEUNR2
STEUNDB
17057-000
67137-200
GUIDE
SET OF SPRINGS
DIE KEY 0 & 45º
Sharpening shim STEUNSH $16. DIE w/SLUG TRAP™ K0&45º
PUNCH CAP (DRIVER)
Retainer Ring (for P.Cap)
TIN Titanium Nitride Coating available.
TiCN Titanium Carbo-nitride Coating also available! Retaining Ring (for Guide)
DRAW BOLT 1/2” x 3½
Price
86668-000
17058-000
17138-000
10828-000
Strippit Compatible, Replacement INSERT BLADES
Adapter Holdr
STE-IH 1pc $195.00 2pc $175ea
Size Range Width .125/3,mm - .375/9,5mm Length 1.968”/50,mm -3.400/86,3mm
STEEL: High Speed M4-Powderd Metal
Blade 1.47”tall 3/8-16 bolts 2.75 spaced
A SHEAR can be added to insert
at minimal additional cost.
Double Inverted Shown.
Regular Inverted or Roof Top also
available.
Blade Length
MIN. - MAX.
1.968 - 3.400
50,mm - 86,mm
CE PART #
Strippit
Part#
Price
STE-IB-RT 0200940-300
Coatings: TIN Titanium Nitride, TiCN Titaium Carbon Nitride, or Alpha available at additional cost.
Option Old Exact Blade 1.58”tall 5/16-16 bolts 1.56spaced
Mate Excel Style, INSERT BLADES
Size Range Width .125/3,mm - .375/9,5mm Length 1.968”/50,mm -3.400/86,3mm
Blade ___”tall _______ bolts 2_.__ spaced
A SHEAR can be added to insert
at minimal additional cost.
Double Inverted Shown.
Regular Inverted or Roof Top also
Blade Length
MIN. - MAX.
1.968 - 3.400
50,mm - 86,mm
Rectangle
CE PART #
Mate
Part#
STE-AM43i
_
Price
Coatings: TIN Titanium Nitride, TiCN Titaium Carbon Nitride, or Alpha available at additional
Wilson DURA Style INSERT BLADES
Size Range Width .125/3,mm - .375/9,5mm Length 1.968”/50,mm -3.400/86,3mm
STEEL: High Speed M4-Powderd
Blade ___”tall _______ bolts 2_.__ spaced
A SHEAR can be added to insert
at minimal additional cost.
Double Inverted Shown.
Regular Inverted or Roof Top also
Blade Length
MIN. - MAX.
1.968 - 3.400
50,mm - 86,mm
Rectangle
PART #
WT
Part#
STE-IBwtd
_
Price
Coatings: TIN Titanium Nitride, TiCN Titaium Carbon Nitride, or Alpha available at additional
Page 11
FAB Strippit Style 4.375OD Guide Bodies
3-1/2 Station
COLE ENGINEERED
Range 1.250”-3.500”/31.7-88.9mm
Punches & Strippers compatible for use in C.E.,Wilson Series 80 & Series 90®, Raskin& Strippit® Mfg. Holders
PUNCH TIP (Donut) Rounds > 1.562
If solid punch is preferred + $12.00 to Punch
Tip price.
Out Board Pin
PUNCH TIP ADAPTER For Round
Punch Tips greater than 1.562.
Notcher Striper
STE-SN-* See
Page 11
4ӯ
4" X.28
ROUNDS
Part#
PUNCH 1 pc 1.250-1.562
PUNCH TIP ADAPTER
PUNCH TIP 1.563-2.250
PUNCH TIP 2.251-2.875
PUNCH TIP 2.876-3.500
STRIPPER PLATE
DIE
DIE w/Slug Trap™ S/F
DIE w/Slug Z-Hugger S/O
STE-Pr
STE-P-ret
STE-PTSr
STE-PTMr
STE-PTLr
STE-S-r
STE-Dr
STE-Dst-r
STEDso-r
SHAPES
Part#
STE-PS-s
STE-PM-s
STE-PL-s
STE-Ss
DIE
STE-Ds
DIE w/Slug Trap™ S/F STE-Dst-s
DIEw/Slug Z-HuggerS/O STE-Dso-s
DIE HEAVY DUTY
STE-Dhds
PUNCH (within 1.500)
PUNCH ( 1.501-2.500)
PUNCH ( 2.501-3.500)
STRIPPER PLATE
.85”
.850
Maximum material ¼”Mild Steel
Round<1.¼/31,85mm
• Shape<1¼diagonal
• Shaped Dies Keyed 0&90º Squares 0&45º
Additional Keys in 45º incremental angles can be
made.
Shaped Punches have 1 location dowel pin.
Additional 45º key or other can be provided.
Three styles of Holders
™
The Quick-Set shown->
Then on page 12
™
The Basic
&
Series 80plus
Page 12
Push in then turn Spring Head
to adjust for punch height
Only on Quick-Set™
FAB Strippit Style
4.375OD Guide Bodies
3½” Station Holders
COLE ENGINEERED
The Basic
™
1
2
Low cost WORK HORSE!
• Keying 0,45,90,135, 180,270º
▪ Length Adjustment is set by placing shim under Punch adapter.
• Quick Release Stripper Retention (Locking Ring)
● Built in Lubrication System Oil resovoir (80/90wt) properly
lubricates internal components.
3
5
#
The Basic™
Code No.
*A STE-GA
*A STE-PD
*ASTE-PLOCAT
*A STE-G
GUIDE ASSEMBLY
3 PUNCH DRIVER
5 PUNCH HOLDER/LOCATOR
4 GUIDE Only
The Quick-Set
™
8
6
9
Wire prior
to Wire
1998 prior to 1998
10: Rd WireSqCurrent
Sq
Full of Featured
Length Adjustment No Shimming! Press in button, then turn spring pack.
• Keying 0,45,90,135, 180,270º
• Quick Release Stripper Retention (Locking Ring)
•Built in Lubrication Oil resivor (80/90wt) lubricates internal components.
The Quick-Set™
GUIDE ASSEMBLY
Adjusting Driver
PUNCH HOLDER/LOCATOR
Adjustment-Plate
Adjustment Key Assembly
GUIDE Only
Retainer Ring
Code No.
*A STE-GA2
*A STE-PHD
*A STE-PH2
*A STE-APL
*A STE-AKA
*A STE-G2
*A 200753-000
Shared Components
Part#
1 PUNCH HEAD w/3 M8X20 SHCS
STE-H
#
S.H.C.S. (M8X25)
DISC SPRINGS (6)
KEY Guide to Turret B.
8 KEY P. Adapter to Guide
9 KEY(Body Internal Key)
2
6
S
#
Shared Components
Part#
Draw Bolt W/Lock washer 3”
STE-8X25
STE-SD
ST-E-GK
ST-E-BK
ST-E-IK
Hi Collar Lock Washer
*A100291-000
*A1001760-000
Below For Older Units
10 Stripper Retaining Ring-rd
10 Stripper Retaining Ring-sq
STE-SRR
STESRWsq
Series 80plus® Holders
#
The Basic™
CE Part#
GUIDE ASSEMBLY
PUNCH DRIVER
PUNCH HOLDER
GUIDE Only
*ASTEGA80+
*A10447
PUNCH HEAD
SPRINGS Set of 5pc
WT #
03252
10448/10067
10073
00442
*A00406
00406
Although CE/Ketec manufactures tools to be fully interchangeable
with Wilson Tool’s HP™ & Series 90® products, there is no affiliation
between Wilson Tool and CE Tooling. HP™ & Series90® are a
registered trademark of Wilson Tool International.
4pc clips. Or Wire Ring
Page 13
T h i n Tu r re t 2 m S t a . C R an ge 1 . 2 5 1 -2 ” S t ri p p i t –2 .02 ”
COLE ENGINEERED
Commonly used in AMADA, Finn-Power & LVD/SHAPE Thin Turret Machines
C.E. Code No.
DESCRIPTION
1/8 3mm max.
Recommended
Punch Grind Life
Punch
Head
SET Punch, Die & Stripper
ASC-PDS-*
PUNCH
ASC-Pm-*
D2 tool steel
STRIPPER
ASC-Sam-*
DIE
Spring
ROUND SHAPE
_=m-Metric, i-Inch
*=R-round S-shape
ASC-D-*
ASC-D-st-*
DIE w/Slug Trap™ S/F
DIE w/Slug Z Hugger S/O ASC-D-so-*
Punch
Drive
Guide
AMADA COMPATIBLE
Stripper
Clip
Maximum material
1/4” (6,mm) Mild Steel
Shaped Dies Keyed 0 & 90º
Squares 0 & 45º
Punches Keyed 0 for
location at 0 & 90º
C.E. Tool
Part#
GUIDE ASSEMBLY
PUNCH HEAD
S.H.C.S. (M8X20)
SPRING DISC (18)
PUNCH DRIVER
Draw Bolt M12 X__
GUIDE Keyed 0,90
KEY (W/M5X8 FH)
*A-ASC-GA
ASC-PH
STRIPPER CLIPS W/SCREWS
ATC-DE-SC
PRICE
ASCDE-8X20
AS-C-SD
ASC-PD
ASC-DBMX__
ASC-G
ATC-E-K
STRIPPIT-THIN TURRET Sta. D 2” “New-2007”
Punch
Head
Part#
DESCRIPTION
Adapter to accept Strippit
-Fab Style Punches
PUNCH
*A-STD-AD
Punch
Driver
Punch
Guide
ASC-Swt-*
STRIPPER WT Style
ASC-D-*
DIE
ASC-D-st-*
DIE w/Slug Trap™ S/F
DIE w/Slug Z Hugger S/O ASC-D-so-*
Punch Fab
Style STE
Ref. Page
12
1/8 3mm Max. Recommended
NON-ADJUSTABLE
Punch Grind Life
Maximum material 1/4”
(6.34mm) Mild Steel
Shaped Dies Keyed 0 & 90º
Square Dies Keyed 0 & 45°
Punches Keyed 0
Holder Keyed 0 & 90º
STE-Ps-*
ASC-Sam-*
STRIPPER am Style
Stripper
Clip (4)
Shape
ASC-Pm-*
2.02 / 51.3mm max
PUNCH Fab Style use w/Adapter
Disc
Spring
10pc
Round
_=m-Metric, i-Inch
*=R-round S-shape
HOLDERS & COMPONENTS
GUIDE ASSEMBLY
PUNCH HEAD
S.H.C.S. (M8X20)
SPRING DISC (10) X3.5
PUNCH DRIVER
Draw Bolt M12 X__
GUIDE Keyed 0,90
Location Pin /Guide to Punch
C.E. Tool
Part#
PRICE
*A STD-GA
ASC-PH
ASCDE-8X20
ST-D-SD
ASC-PD
ASC-DBMX__
STD-G
STD-GP-Pin
STRIPPER CLIPS W/SCREWS
ST-D-SC
FAB (Strippit/Raskin)
Style 2” Tools
Machines prior to 1980 which had 2” station option.
Pricing is for Punch Tip
Sizes .093 (2,3mm) +
A
Page 14
SIZE RANGE
1.251-2.000”/31,85
-50,8mm
DESCRIPTION
SET Punch, Die & Stripper
PUNCH
STRIPPER A=2,25 X.25
STRIPPIT® Mfg. Holder
STRIPPER
A=2,293 X.20
RASKIN Mfg. Holder
DIE w/Slug Trap™
C.E. Code No.
*=R-round S-shape
STD-PDS_-*
STD-P-*
STD-S1-*
STD-S2-*
STD-Dst-*
Round
Shape
THIN TURRET
STYLE
Thin Turret 3½ Sta. D Full Body 4.133”OD Guide Bodies
COLE ENGINEERED
Pricing is for Punch Tip Sizes .093 (2,3mm) and Above
Range 1.251-3.500 31,7-88,9MM
C.E. Part#
Description
*=R-round S-shape
PRICE
PRICE
M12 THREAD
SET Punch, Die & Stripper-AM
STRIPPER
Options Industry
3-3/4"
.28
Standard
Holders
Stripper for
WT S80/S90
Holders Only
1.19
Punch, Die & Stripper-WT
ASD-PDSm-am
ASD-PDSm-wt-*
PUNCH
D2 tool steel
ASD-Pm-*
PUNCH
M2 tool steel
ASD-Pm-hs*
STRIPPER PLATE am
ASD-Sam-*
STRIPPER PLATE -wt
ASD-Swt-s
DIE
ASC-D-*
DIE w/Slug Trap™ S/F
ASC-D-st-*
DIE w/Slug Z Hugger S/O
ASC-D-so-*
Shaped Dies Keyed 0 & 90º Squares 0 & 45º
Additional Die Keys Additional.
Shaped Punches Keyed At 0° Additional 45º Key Extra Cost.
Maximum material 1/4” Mild Steel
Thin Turret “Amada, Finnpower, LVD, etc.. Full Body or 1” shank
For use in Thin Style Turret from Amada, LVD, Euromach
C.E. Tool
DESCRIPTION
Allow use of 1” shank punches or Full Body
Adapter Only
*A-ASDAWT
PRICE
Part#
GUIDE ASSEMBLY
For Full Body Punch
PUNCH HEAD
S.H.C.S. (M6X20)
SPRING DISC (4)
PUNCH DRIVER
*A-ASD-GA
ASD-PH
ASD-6X20
ASD-SD
ASD-PD
Draw Bolt i=1/2”or m= M12 X50
ASD-DBMX50
GUIDE Keyed 0,90 & 45°
KEY (W/M5X8 FH)
*A-ASD-G3
ATDEK
STRIPPER CLIPS W/SCREWS
*A-AS-D-SC
1” shank Punches
page 15 & 16.
Guide Assembly-Fab *A-ASD-GAwt
90014N
917.00
Page 15
Thin Turret 3-1/2” Sta. D (Inch)
COLE ENGINEERED
For use in WT Series 80 or 90® Thin Turret Holder
Punch=Fab/Strippit Style, Die=Thin Turret 1.19 Height
Stripper = Industry Standard (Amada) Style or WT –S80/S90 StyleRR
SHAPED
C.E. Tool #
#= R:Round
S:Shape
PUNCH under <1.500
STE-PS-s
PUNCH 1.501-2.500
STE-PM-s
PUNCH 2.501-3.500
STE-PL-s
STRIPPER PLATE
ASD-S-s
DIE D2 steel!
ASD-D-s
DIE w/Slug Trap™ S/F
DIE W/Slug Z-Hugger S/O
Price
shaped
1/2-13”Punch threads. If M12 is wished, go to page 16.
Out Board Pin
On Shapes for
Superior Alignment.
ASD-D-st-s
TO USE PUNCHES KEYED WITH OUT BOARD
PINS IN YOUR ORIGINAL AMADA UNITS
REPLACE AMADA’S LOCATION KEY WITH
C.E. Tooling’s KEY
*A-ASD-003
ASDso-s
PUNCHES HAVE
OUTBOARD PINS
FOR SUPERIOR
ALIGNMENT
PUNCH TIP (Donut) Rounds > 1.562
Solid punch Available At Minimal Extra Charge.
CE Part#
ROUND
#= R:Round S:Shape
Price
Round
PUNCH 1.250-1.562
STE-P-r
PUNCH TIP ADAPTER
STE-P-RET
PUNCH TIP 1.563-2.250 STE-PTS-r
PUNCH TIP 2.251-2.875 STE-PTM-r
PUNCH TIP 2.876-3.500 STE-PTL-r
STRIPPER PLATE
ASD-S-r
PUNCH TIP
ADAPTER for
Rounds Tips >
1.562
DIE D2 Steel
DIE w/Slug Trap™ S/F
DIE W/Slug Z-Hugger S/O
ASD-Dr
ASD-D-r
ASD-D-st-r
3 3/4"
Industry Standard Thin Style Stripper
.28
WT Style Stripper
Only used on WTS80/90 Holders
1.19
Shaped Dies Keyed 0 & 90º Squares 0 & 45º
Additional Die Keys Additional.
Maximum
material
Shaped Punches Keyed At 0°
1/4” Mild
Steel
Additional 45º Key Extra Cost.
Shapes on angles Of Punch & Die Also Made-To-Order.
Page 16
Thin Turret Die
= Thick turret Die
Original Style 3½”1m & 2m Sta. D
Fab/Strippit style punch but with M12 Threads
PUNCH TIP -Donut Rounds >
1.562
Solid punch available at minimal
Style-1
extra charge!
Out Board Dowel Pin
for Superior shape
alignment
Style 1
PUNCH TIP
ADAPTER
FOR ROUND
PUNCH TIPS
> 1.562
Style-2 Punch,
with .250 Key Way
in Shank
Thin Turret COMPATIBLE
ROUND
#= R:Round S:Shape
PUNCH 1.250-1.562
ASE-P1m-r
Punch Tip ADAPTER
ASE-P-RET
PUNCH TIP 1.563-2.250
STE-PTS-r
PUNCH TIP 2.251-2.875
STE-PTM-r
PUNCH TIP 2.876-3.500
STE-PTL-r
STRIPPER PLATE
ASD-S-r
DIE D2 steel
ASD-D-r
DIE w/Slug Trap™ S/F
DIE W/Slug Z-Hugger S/O
3 3/4"
Tool
Code No.
Thin Turret COMPATIBLE
SHAPES
THIN TURRET
STYLE
Thin Turret 3½ Sta. D (Metric)
COLE ENGINEERED
Price
Round
ASD-D-ST-r
ASD-Dst
Code
*=R-round S-shape
PRICE
SHAPE
1.19
To use punches keyed with
out board pins in original
AMADA Manufactured Units
Replace Amada’s location
key with CE Tooling’s
PUNCHES HAVE
OUTBOARD PINS
FOR SUPERIOR
ALIGNMENT
*A-ASD-003
PUNCH w/M12 thread & out board pin
ASD-P2m-s
PUNCH w/M12 thread & .250 key way
ASD-P1m-s
STRIPPER
DIE only D2 steel
DIE w/Slug Trap™ S/F
DIE W/Slug Z-Hugger S/O
ASD-S-s
ASD-D-s
ASD-D-st-s
ASD-Dso-s
Thin Turret Style 3½” Sta. D Shearing Tool
Stocked Sizes .250”X3” & 5,0X84,mm
AESI ABS COMPATIBLE
DESCRIPTION
PUNCH D2 steel
ASDPm-S
PUNCH M2 steel
ASDPm-hs-s
DIE w/SLUG TRAP™
ASDDsh-st-S
GUIDE ASSEMBLY
Excludes Punch Slip Fit Guide
*
WORK
CLAMPS
Guided Punch, can achieve 50%
more tool life than same punch used
in a regular guide. How: Punch Tip is
supported and aligned by the fitted
opening at the face of the guide.
C.E. Tool
Code No.
ASDGA-sh
PUNCH HEAD
ASDPH
SPRING DISC (4)
ASD-SD
PUNCH DRIVER
ASD-PD
DRAW BOLT M12X70
ASD-DB-12X50
ABS=M14X70
PRICE
SPRING RETAINER
ASD-SR-SH
Set Screws require 4 M4X6
ASD-SS-4X6
GUIDE .25X3” or 5,X84,mm
ASD-G-sh
KEY (W/M5X8 FH)
AT-DE-K
Page 17
Strippit /LVD MULTI-TOOL
®
COLE ENGINEERED
PUNCH or DIE Grind Life: .060”/1,5mm
Slug Trap™ Dies
LVD/AS-MT8 Stripper
Punch
Body .266”dia.
X 70,6mm
Shapes: X2 Key
flat 0&90
1.052”diameter
.125 thick
.26”+
ST/LVD-MT8 Stripper
.68”dia
Dies differ between Strippit Fab & LVD-Thin Turret Machines.
ST- die is .594”tall
has .25”wide key X.1
LVD die is .70” tall with
3/16”dowelpin .34” up
Both Dies are
.551"/14mm
1” dia.
STYLE
Range
3 Sta.
- 1.25”
31,75mm
FabThin
8 Sta.
-.500
12,7mm
30 Sta.
-.250”
6,35mm
Punch
Catalog Code
Round STMT3Pr
Shape STMT3Ps
Round STMT8Pr
PRICE
Strippit
Code
M2 Steel
Strippit
PRICE
Code
Stripper
A2 Steel
Catalog Code
catalog Code
STMT3Dr
200966
STMT3Ds
Or
STMT3Ss
Code
202302
OR
STMT8Sr 200732
OR
STMT8Ss 200743
LVMT8Dr 202856
STMT8Ds 2 0721
OR
Strippit
STMT3Sr
202305
STMT8Dr 200720
200714
Shape STMT8Ps 200715
LVMT8Ds 202857
Round STMT30Pr 200734
LVMT30Dr 200739
STMT30Sr 200737
Shape STMT30Ps 200735
LVMT30Ds 200740
STMT30Ss 200738
Smart Mark®
STMTSMP
Thick
202864
8 Sta. Round ATMT8Pr
-.6299
202855
16,0mm Shape ATMT8Ps
ATMT8Dr 202856
ATMT8Ds 202857
P:H=.812dX.246-.3dX.025 B=.6299 Pin=1/8 .62 from head flange
Page 18
Die
Slug Trap™
STBSr
200732
ATMT8PDSr
STBSs
200743
ATMT8PDSs
No loc tab
D:1.00diaX.7 3/16dowel .34from bottom
PRICE
SPECIAL APPLICATION FORMING TOOLS
HIGHER PRODUCTIVITY THROUGH SUPERIOR ENGINEERING
COLE ENGINEERED
EXCLUSIVELY From C.E. TOOLING
The QUICK-SET™
This patented tool length
adjustment unit allows for
set up of form
tools length to as close
as .0025” with only a lift and
turn of the outer knurled collar.
Length can’t change during use. A half
to one hour set up time is now reduced to
minutes.
ELECTRICAL
SINGLE Sp-60
KNOCK OUTS
DOUBLE Sp-61
EMBOSSES
OR SHAPED
ROUND
D
C
A
Form Up Sp63
Form Down Sp74
B
D
D
C
A
C
B
B
B
A
C
D >= 45º DIE w/No Stripper
Quick-Set™ Punch and Die Cat.
Code *FAT_PD-D72
D>= 45º DIE w/No Stripper
Quick-Set™ Punch and Die Cat.
Code *FAT_PD-U63
D < 45º DIE w/Built in Stripper
D < 45º DIE w/Built in Stripper
Quick-Set™ Punch and Die Cat.
Code *FAT_PD-U63
A
Pipe Actual Pipe Actual
Size
Size
1/2 .875 1½ 2.000
3/4 1.125 2” 2.500
1” 1.375 2½ 3.000
1¼ 1.750 3” 3.625
Quick-Set™ Punch and Die Cat.
Code *FAT_PD-D72
TO ADJUST, LIFT & TURN
BRIDGE TOOL
SINGLE Sp-65
THREAD FORM DOWN ONLY
C.E.TOOLING
DOUBLE Sp-66
C
E
D
F
G
B
Replaceable Top Inserts *FIP81 Bottom *FID81
Ordering Notes:
Order by Screw & Thread size
Limitations Thread Pitch must be < than
material thickness.
Contact C.E. Tooling Engineers with your specific needs,
and they can discuss the feasibility and pricing for Thread
SP-65
SP-66
EXTRUSIONS
A
C
E
GROUND SYMBOL
Keyed 4 Ways
Standard=1/2ӯ +$50 for non standard Longest horizontal line=3/8 length
DOWN 1¼ w/Quick-Set
UP 1¼ w/Quick-Set
DOWN 1¼ w/Quick-Set
UP 1¼ w/Quick-Set
½” no Quick-Set
½” not available
½” no Quick-Set
½” not available
Page 19
SAVE! MASTER FORM TOOL HOLDER Accepts
Inserts to perform common forming Applications
COLE ENGINEERED
Adjust the Quick-Set™ to
its shortest length by lifting
and rotating of knurled collar
clock wise.
INSERT PLATE
*FIP $20.50 Included with die
DIE BASE
Cat. Code *FATBMDB $100
STRIPPER PLATE
.28 I.D. Part# *FCDIPD $32.50
53” I.D. Part# *FCDIPV $32.50
MASTER
PUNCH
HOLDER
There are two different
insert styles. All but form
up coins use a .28”(7,mm)
I.D. hole through the
stripper plate. Form up
Coins use .53”/25,4mm
I.D. hole.
PUNCH
CHIP
Code *FSTCMPH
O-RING
Code *FMPH
for.
URETHANE
P.STRIPPER
INSERT CHANGING
INSTRUCTIONS: While holding die base,
pull knurled portion of the insert plate apart from
the die base. If replacing with new insert, first
check that I.D. hole in the stripper plate, is large
enough to allow insert to go through. Insert the
Insert Plate into die assuring alignment of the pin
extending out of the die base to mate with one of INSERT
two holes in the stripper plate. To keep the die RETAINER
Part#*FCPIR
base in good working order and prolong its life,
periodically add grease to the shoulder bolts and
the rubber “O”-ring in the center I.D. hole.
Form-Down Yellow
Part# *FCPUD $14.95
Form Up Orange
Part# *FCPUU $14.95
CE can supply Inserts & Die for use in competitor master Form Holders at reduced cost!
CE Tooling
Quick-Set accept Amada
or WT Inserts
WT Style
Dedicated Style
TO ADJUST, LIFT & TURN
C.E.TOOLING
COLE ENGINEERED
TOOLS
THOR D2
D
B
Page 20
C
Mate
UltraTec™
E A S Y A D JU S T H E A D
Amada Style
Form Inserts for CE, WT & Amada Style Holders
COINING /Counter Sink Inserts/Chips
COLE ENGINEERED
For pre-pierce hole size, See chart/formula in Technical Reference booklet Section 1
D
NO ROLL-OVER
PRE-PUNCH
HOLE
H
B
RECOMMENDED IF "H" IS
THICKER THAN MATERIAL
A
C
WT Style Insert
WT
*FIPWT56
$84.30
CE Style Insert
*FIP56 $84.30
CE
Ø.500
.6320
AT Shown, similar
available for ST/
AS in Sta.½ or 5/8
Form Up
Amada Style Chip
#43114
CE#*FIP56AM
$51.00
AMADA
Ø.472
.50
.58
A
C
D=ANGLE
CE
B
C
C
B
B
Down *FIP54 $71.20
B
HALF SHEAR
FORM DOWN OR FORM UP
Master Unit Accepts Replaceable
Half Shear Insert .25”(6,1mm)
Maximum B dimension Dedicated
Quick-Set Punch Holder and Die
must be used for
Inserts/Chips For CE Holder
Top=*FIP51 $71.20 *FID51 $84.00
For WT Style Holder
P.Chip = CE# *FIP51wt
D.Chip = CE *FID51wt
For sizes>.25”(6,1mm) *FIPWT56
For Amada Style Holder
code Set PA203202S Punch Ass’y
PA203202P Die Ass’y PA203202D
P. Chip 8700069 = CE *FIP51am
D. Chip 5511491 = CE *FID51am
Dedicated die is
suggested over
B
EXTRUSIONS INSERTS
HEIGHT
DETERMINED
BY PRE-PUNCH
HOLE SIZE
B
.500 MAX.
Up *FIP50 & *FID50 $78.75
A
EMBOSS &
EXTRUSION
B
.500
MAX.
A
.250
MAX.
CENTER POINT
TWO HALF SHEARS USED
FOR ALIGNING TWO SHEETS
Replaceable Insert
For CE Holder Top *FIP57 $50.30
For WT *FIP57wt $50.30
For Amada
Use with No hole Die ATB-Dr
TWO HALF-SHEARS
USED FOR SHEAR STOPS
B
.250 MAX.
Replaceable Insert
Top *FIP51 $71.20
Bottom *FID51 $84.00
A
Replaceable Insert
For CE Holder Top FIP58 $71.20
Bottom *FID53 $57.80
For WT Top *FIP58wt Bottom
*FID53wt
Page 21
LOUVER & CARD GUIDE TOOLS
COLE ENGINEERED
TO ADJUST, LIFT & TURN
POCKET
INSERT
FORMING
INSERT
CUTTING
INSERT
POCKET INSERT
FORMING INSERT
DIE ASS'Y FOR CARD GUIDE
DIE ASS'Y FOR LOUVER'S
STANDARD AND PROGRESSIVE
STYLE LOUVERS AND CARD-GUIDES.
A
PROGRESSIVE TOOLS ARE MADE TO EXACT
MATERIAL THICKNESS. THE LENGTH IS
UNLIMITED THROUGH NIBBLING OPERATION.
ENDING RADIUS MUST BE MORE GRADUAL.
D
B
E
A
D
C
B
(11 GAGE MAX.)
C
(11 GAGE MAX.)
LANCE & FORMS
Form Down LOUVER
STD. PUNCH
INSERT FOR
OPEN STYLE
MASTER HOLDER
DOUBLE BEND
SP-77
C
B
A
DOUBLE BEND
LESS THAN 90
FORM OF 90
SP-79
SP-78
LANCE STYLE
SP-80
D
Standard LOUVER Sizes
“A”
“B”
“C”
“D”
Length
A
B=.250 MAX.
C
C
C
E=WIDTH
OF TAB
PROGRESSIVE STIFFENING RIB
Punch is made for
a specific material
thickness
B
Unlimited Length
Width Nibbles
A
R
Standard
“A”
“B”
“R”
Size
3/8
3/16
3/16
Other sizes available on MADE-TO-Order!
Page 22
2”
2-1/2”
1/2”
3/16”
3/4”
3”
3-1/2”
5/8”
1/4”
15/16
4”
4-1/2”
3/4”
1/4”
1-1/8”
Sheet Lifter Dies
Lifter dies are placed in
turret on each side of a
form tool.
1-1/4” Part# ATBD-Lifter
COLE ENGINEERED
CHARACTER MARKING TOOLS
DEDICATED MARKING UNITS Produced to stamp Logo’s, Names, Part No., etc.. Contact our
tooling engineers to discuss your particular application. Camera Ready Art Work or
Cad
-.DXF/.IGES files are required for Logo’s. Dedicated form tools can be produced to stamp
Logo’s, Names, Part No., etc..
SHARP FACE CHARACTER STAMP INSERT HOLDERS
Available 1/16, 3/32, 1/8, & 3/16 width X ¼ height. 1/8 is standard. 1/16, 3/32 & 3/16 Are Also
Available. Blanks/spacers cost = 60% of regular character price
1/8 *ACHAR⅛ stamps .09X.15 1/16 *ACHAR1/16 stamps .06X.12” • 5/32 *ACHAR5/32 stamps .125”X.19”,
3/16 *ACHAR3/16 stamps.156X.23
Spacer Kit I*ASPACER includes widths of: 4 each 1/16, 3/32,⅛, 2 pcs 3/16
FORM UP
1¼
Sta.C
Single
Row
Catalog
PUNCH
Cartridge
1/8
10
N/A
N/A
STC-Dr-0
3/16
6
1/16
16
PUNCH
*FSTC-PDU
DieComplete *FSTC-DDU
*FSTC-PDD
STC-Dr-0
Character
Qty Per Row
1/16
20
1/8
10
3/16
6
1/16
16
*FASD-SSU
PUNCH
*FASD-PBB
Cartridge
*FATDDCS
DieComplete *FATDSDU
SET
3½Sta.
E
Single
Row
3½”Sta. E
Double
Row
3/16
5
1/16
48
1/8
24
1/8
8
1/16
50
1/8
25
*FASD-SDU
*FASD-SDD
*FASD-PDD
*FATD-CD
ASD-Dr-0
Rotate Cartridge for
4 way positioning
3/16
16
Accessories:
Plunger Screws
*ACHLOCKB
Character
1/16
1/8
3/16
1/16
1/8
3/16
Qty Per Row
48
24
16
50
25
16
Catalog
Catalog
*FSTE-SSU
*FSTE-PBB
*FATDDCS
*FSTE-SDU
*FSTE-SSD
*FSTE-PSD
*FSTD-CS
STE-D-S-0
Character
Qty Per Row
1/16
48
Catalog
Catalog
SET
PUNCH
Cartridge
Die Complete
*FSTE-SDU
*FSTE-PBB
*FSTE-DCD
*FSTE-SDU
*FSTE-SDD
*FSTE-PDD
*FSTD-CD
STE-Dr-0
Character Width 1/16
Qty Per Row
48
1/8
24
1/8
24
3/16
16
3/16
16
1/16
50
1/16
50
FORM Up Keyed
FORM DOWN
PUNCH
*FASD-PBB
Cartridge
*FATDDCD
Die Complete *FSTE-DDU
SET
PUNCH
Cartridge
Die Complete
Keyed 0° &
90°
3/16
5
*FASD-SSD
*FASD-PSD
*FASD-CS
ASD-D-s-0
3/16
16
FORM DOWN
0 & 180°
Catalog
SET
Character
Qty Per Row
3½Sta.D
Double
Row
1/8
8
*FSTC-SDD
Catalog
3½Sta.D
Single
Row
Price
*FSTC-SDU
SET
Double
Row
Catalog
*FSTC-SSD
*FSTC-SPD
Die Complete *FSTC-SDU
Character
1/16
Qty Per Row 20
1¼ Sta.C
Price
*FSTC-SSU
*FSTS-SPU
N/A
SET
FORM DOWN
1/8
25
1/8
25
FORM UP
Keyed 4 places
Cartridge Lock
Small *AchlockA
Large *AchlockB
3/16
16
3/16
16
Go to our Section 1
booklet for more
Info on Marking.
Page 23
COLE ENGINEERED
Specializing in tooling and machine parts for
Amada, Behrens, Boschert, Chassis Maker, Diacro®,
Danobat, Durma, Ehrt, Euromac, Finnpower, Haco, Murata
Wiedemann, Nisshinbo, Omes, Pullmax, Rainer, Salvagnini,
Simasv, Strippit®, Trumpf, Raskin, Whitney, Yawei
and similar presses.
Further offering of tools for: Brake Press, Ironworker,
Shear Blades, Stamping Die-Sets C-Frame, Tube & Pipe
PRESS
CE TOOLING, INC.
2560 W. Brooks Ave.
N. Las Vegas NV 89032
[email protected]
Tel. 702 736-2598
www.cetooling.com
Fax 702 736-3038
LOCAL SALES REPRESENTATIVE
DISTRIBUTORS
Page 24