SDS - JBS Industries

Safety Data Sheet
JB 100 (PD-100)
Section 1. Identification
Product Identifier
Synonyms
Manufacturer Stock
Numbers
JB 100 (PD-100)
WHITE POWDER
N/A
Recommended use
Uses advised against
HIGH FOAMING POWDER
N/A
Manufacturer Contact
Address
JBS INDUSTRIES
2550 HENKLE DR
LEBANON, OHIO, 45036
USA
Phone
(513) 228-2800
Emergency Phone
(800) 424-9300
CHEMTREC
Fax
(513) 228-2810
Section 2. Hazards Identification
Classification
Signal Word
Pictogram
Hazard Statements
Precautionary Statements
Response
CORROSIVE TO EYES AND SKIN - Category N/A
EYE DAMAGE/IRRITATION - Category 2
SPECIFIC TARGET ORGAN TOXICITY (Single Exposure) - Category 3
Warning
May cause respiratory irritation.
Call a poison center/doctor/911 if you feel unwell.
If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses,
if present and easy to do. Continue rinsing.
If inhaled: Remove person to fresh air and keep comfortable for breathing.
If skin irritation or rash occurs: Get medical advice/attention.
Page 1 of 5
Prevention
Avoid breathing dust/fume/gas/mist/ vapors/spray.
Use only outdoors or in a well-ventilated area.
Store in a well-ventilated place. Keep container tightly closed.
Store locked up.
Dispose of contents/container according to local, state, and federal laws.
Storage
Disposal
Ingredients of unknown
toxicity
0%
Hazards not Otherwise
Classified
N/A
No Data Available
Section 3. Ingredients
CAS
6834-92-0
Ingredient Name
Silicic acid (H2SiO3), disodium salt
Proprietary Surfactant Blend
Weight %
1% - 5%
1% - 95%
Occupational exposure limits, if available, are listed in Section 8.
Section 4. First-Aid Measures
Eye
Skin
Ingestion
Inhalation
Immediately flush eyes with plenty of water for at least 15 minutes. Get immediate
medical attention.
Immediately wash skin with soap and plenty of water. Remove contaminated
clothing. Get medical attention if symptoms occur. Wash clothing before reuse.
DO NOT induce vomiting. If vomiting does occur, have the victim lean forward to
prevent aspiration. Rinse mouth with water. Seek medical attention. Never give
anything by mouth to an unconscious individual.
Remove to fresh air. If not breathing, give artificial respiration. If breathing is
difficult, give oxygen. Get immediate medical attention.
Section 5. Fire Fighting Measures
Suitable Extinguishing
Media
Unsuitable Extinguishing
Media
Fire fighting instructions
Fire fighting procedures to surrounding materials
N/A
As in any fire, wear self-contained breathing apparatus pressure-demand,
MSHA/NIOSH (approved or equivalent) and full protective gear. Move container
from fire area if it can be done without risk. Avoid inhalation of material.
Page 2 of 5
Section 6. Accidental Release Measures
Containment
Reporting
Clean-up
Clean up spills immediately, observing precautions in Protective Equipment
section.
Isolate hazard area. Keep unnecessary and unprotected personnel from entering.
Shovel dry material into a suitable container. All spills should be contained and
offered for disposal per state or local laws.
Section 7. Handling and Storage
Storage
Handling
Store in original container at temperatures below 120 degrees F. Product is best if
used within 6mths of purchase. Do not store in metal containers
Do not get in eyes, on skin or clothing. Avoid breathing (dust, vapor, mist, gas).
Section 8. Exposure Controls/Personal Protection
Occupational Exposure
Limits
Personal Protective
Equipment
Engineering controls
Eye/Face Protection
Skin Protection
Respiratory Protection
Ingredient Name
ACGIH TLV
OSHA PEL
STEL
Silicic acid (H2SiO3), disodium salt
Proprietary Surfactant Blend
N/A
N/A
N/A
N/A
N/A
N/A
Goggles, Gloves
Facilities storing or utilizing this material should be equipped with an eyewash
facility and a safety shower.
Wear safety glasses.
Neoprene gloves
Good general ventilation Wearing of a dust mask is recommended.
Page 3 of 5
Section 9. Physical and Chemical Properties
Physical State
Color
Odor
Odor Threshold
Solubility
Partition coefficient Water/n-octanol
VOC%
Viscosity
Specific Gravity
Density lbs/Gal
Pounds per Cubic Foot
Flash Point
FP Method
Ph
Melting Point
Boiling Point
Boiling Range
LEL
UEL
Evaporation Rate
Flammability
Decomposition Temperature
Auto-ignition Temperature
Vapor Pressure
Vapor Density
SOLID
POWDER
CHEMICAL
N/A
COMPLETE
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
1990 F
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Section 10. Stability and Reactivity
Stability
Hazardous Polymerization
Conditions To Avoid
Incompatible Materials
Stable at normal temperatures and pressures.
Will not occur.
Strong Acids
Acids, prolonged contact with aluminum, brass, bronze, copper, lead, tin, zinc, or
alkali sensative metals or alloys.
Section 11. Toxicological Information
No Data Available
Section 12. Ecological Information
No Data Available
Page 4 of 5
Section 13. Disposal
WASTE DISPOSAL
Offer surplus and non-recyclable solutions to a licensed disposal company. Contact
a licensed professional waste disposal service to dispose of this material. Empty
containers should be disposed of as unused product.
Section 14. Transport Information
UN Number
UN Proper Shipping Name
DOT Classification
Packing Group
3253
DISODIUM TRIOXOSILICATE
8 CORROSIVE
PGII
Section 15. Regulatory Information
SARA
Ingredient(s) - State
Regulatory
SARA 302 Components: None SARA 313 Components: This material does not
contain any chemical components with known CAS numbers that exceed the
threshold reporting levels established by SARA Title III, Section 313 SARA
311/312 Hazards: Acute Health Hazard
Disodium Metasilicate CAS-No. 6834-92-0 Right to Know Components:
Pennsylvania New Jersey
Section 16. Other Information
Revision Date
NFPA
HMIS
DISCLAIMER:
00/00/00
Health: 3 Fire: 0 Reactivity: 0
Health: 3 Fire: 0 Reactivity: 0 Personal Protection: B
The information contained herein is believed to be accurate and is offered in good
faith. This information relates only to the specific material designated and may not
be valid for such material used in combination with any other materials or in any
process. Mixing this product with any other materials may change the
characteristics such as flash point, flammability or health effects. Because product
use is beyond our control, no warranty is given, expressed or implied.
Page 5 of 5