Infrared Sauna Liner Kit Installation Guide

Infrared Sauna Liner Kit
Installation
Guide
INTRODUCTION
This booklet is only intended to assist in constructing a safe and effective
infared sauna. Please thoroughly read this entire booklet before commening construction.
For safety concerns, pay special attention to Emitter Installation (Sect 1)
and
(Sect
2). PRODUCT WITHOUT FIRST
IT ISBackrest/Emitter
UNLAWFUL TOGuards
INSTALL
THIS
OBTAINING A PERMIT FROM THE LOCAL ELECTRICAL INSPECTION
AUTHORITY.
ALL ELECTRICAL WIRING BETWEEN SAUNA HEATERS, HIGH
POWER CONTROLS MUST BE THROUGH A LIQUID TIGHT METAL
CONDUIT RACEWAY.
ALL HEATING COMPONENTS MUST BE LOCATED AWAY FROM ANY
COMBUSTIBLE MATERIALS, AND MUST BE KEPT AWAY FROM THE
DIRECT RADIANT PATH OF THE HEAT DISPERSED FROM
THE HEATERS.
DO NOT INSTALL HEATERS ON CEILING, AND MUST BE KEPT
A MINIMUM DISTANCE OF 24 INCHES BELOW THE CEILING
SURFACE.
THE COMMANDER CONTROL HAS A BUILT IN HI-LIMIT CUTOFF
RESET SWITCH, THE CAPILARY TEMPERATURE SENSOR FROM
THAT SWITCH MUST BE ALSO LOCATED WITHIN THE SAUNA
ROOM AT CEILING HEIGHT.
All wiring to the heaters must be routed away from any
direct radiation from the infrared heating units, and be
made with liquid tight conduit.
For electrical hook up follow the wiring diagram. This work should
be done by a Licensed Electrician only.
Use minimum 90 deg. C/300V copper conductors only, sized in
accordance with National and Local electrical codes.
The information in this book is intended to assist in building a safe and effective infrared sauna.
Saunacore Inc will not be held responsible or liable for the application of the information
contained in this book. The customer(s) assumes all responsibility to ensure the safety of their
sauna and ensure that the sauna(s) comply with building and electrical regulations.
Saunacore assumes no responsibility or liability for any errors or inaccuracies that may appear
in the information content contained in this installtion book.
The content of this book is furnished for information use only, is subject to
change without notice, and should not be construed as a commitment by
by Saunacore or the author Kevin Halsey.
SAUNACORE
INSTALLATION GUIDE
Do-It-Yourself
Infrared Sauna Wiring Diagrams
Please immediately check for any hidden damage that may have occurred in shipping. If any damage is
found you mustnotify the delivering carrier within 72 hours. Missing items must be reported to your vendor
within 48 hours of rec eipt.
Electrical components must be installed by a qualified licensed electrician and must meet local
electrical code.
SAUNACORE
905.857.8085
www.saunacore.com
Infra-core Installation Schematic for Emitters
120 Volt Systems (with 120 volts to emitters)
SAUNACORE
L1
N
G
N
L1
L1
G
N
L1
N
G
G
N
G
High
Limit
High
Limit
High
Limit
High
Limit
G
L1
COMMANDER CONNECTION BOX
L1
COMMANDER
KEY PAD
L2
HEAT
HEAT
G
MAIN POWER SUPPLY
SAUNA ROOM
TEMP SENSOR
ELECTRONIC CIRCUIT BOARD
FAN
LIGHT
G
G
G
G
G
www.saunacore.com
Infra-core Installation Schematic for Emitters
240 Volt Systems (dual 120 volts) (with 120 volts to emitters)
SAUNACORE
L1
N
N
L1
G
G
L1
N
L1
L1
N
N
G
G
N
L1
N
L1
G
L1
N
G
G
High
Limit
High
Limit
High
Limit
G
N
N
G
G
High
Limit
High
Limit
High
Limit
High
Limit
High
Limit
L2
G
G
L1
COMMANDER CONNECTION BOX
L1
COMMANDER
KEY PAD
L2
HEAT
HEAT
G
MAIN POWER SUPPLY
SAUNA ROOM
TEMP SENSOR
ELECTRONIC CIRCUIT BOARD
FAN
LIGHT
NEUTRAL
G
G
G
G
www.saunacore.com
Infra-core Installation Schematic for Emitters
240 Volt Systems (with 240 volts to emitters)
SAUNACORE
L1
N
G
N
L1
L1
G
N
L1
N
G
G
N
L2
G
High
Limit
High
Limit
High
Limit
High
Limit
G
L1
COMMANDER CONNECTION BOX
L1
COMMANDER
KEY PAD
L2
HEAT
HEAT
G
MAIN POWER SUPPLY
SAUNA ROOM
TEMP SENSOR
ELECTRONIC CIRCUIT BOARD
FAN
LIGHT
G
G
G
G
G
www.saunacore.com
Infrared Sauna Control Module Connection Diagram
Infrared Sauna Control Module
(located on roof exterior)
Light Plug Fan Plug
Commander
Temperature
Sensor
Emitter Plug
Emitter Plug
Plug
Emitter Plug
Plug
Emitter Plug
Magnetic Contactor
Com
V+
Ground
12/2
Power to Radio
(connect to radio harness
in radio mounting wood box)
Power
Supply
WallOutLet
Notes:
DedicatedElectricalOutlet
Radio Transformer
(radio power supply)
Connect all electrical wires to their appropriate receptical on the power box located on the roof of the sauna
Plug cord coming out of power box into a dedicated isolated circuit. Do not overload yourelectrical wiring. Have a qualified licensed electrician check to make sure that your installation
meets local electrical code.
Emitter plugs are 120 volt typical recepticals. Although this does not reflect on the voltage
of the control, it may be 240 volts. The control box and the wall outlet plug for the sauna
states the saunas voltage.
J7 - C - PREHEAT
J6 - T - TEMP LOCK
J5 - F - CELC / FAHR
J4 - P - 30/60 MINUTES
ADD JUMPER TO CHANGE SETTINGS
Commander Control Operating Instructions
SAUNACORE
Operation Instruction for Sauna Commander Control
LIGHT Indicator1. Activate main power from Electrical panel.
2. Once the power is on, the current room temperature will be
displayed in the "Commander" readout window.
3. To activate the sauna heater press and release the ON/OFF
button in the center of the Commander Control.
4. The Light and Heat displays will illuminate. The heater is now
activated and the sauna interior light has been activated.
FAN Indicator-
HEAT Indicator-
5. To set/change the sauna temperature at any time, hold the
ON/OFF button down until the temperature you desire is set,
than release the button. The temperature will be displayed in
readout window. The temperature can be set between 30
degrees Celsius up to 90 degrees Celsius at one degree
increments. The temperature set will remain unless the main
power is turned off, if this occurs it will be set at 30 degrees
Celsius.
6. If your sauna does have a fan connected to the Commander
Connection Box, it will automatically activate when the sauna
reach a certain temperature and the Fan display will illuminate.
(fan equipped models)
7. To shut off the heater press and release the ON/OFF button
located in the center of the Commander Control pad.
8. If your heater has the Standby feature it will activate immedately after it has been turned off. The heater at this point will
re-activate and remain on for 1 hour of operation (1 min on /
1 min off simutaneouly), it will then finally shut off.
STANDBY Indicator(optional)
9. During the Standby mode, if you wish to activate the heater at
full capacity and bypass the Standby mode, simply press the
ON/OFF button.
10.Whenever the heater shuts off, the sauna light will remain on
for an extra 5 to 10 minutes and it may blink on-off to notify
you that it is ready to shut down.
ON/OFF Button(+Temp Set Button
Hold Down)
Note:
•
All sauna heaters will automatically shut off in 30 minutes
•
•
Some of the sauna systems may operate with dual voltage.
For safety precautions, when the sauna is not being used
and during service, ensure that the main power supply is
switched off.
Infra-Core & Horizon Models
(Infrared Sauna Control Module - Internal Wiring Diagram)
V+ COM
L
N
GND
Stereo & Transformer Wiring Diagram
(After Market Radio Installation for Dry Sauna)
(110 Volts or 220 Volts Power Input)
110 V Outlet
L
N
GND
COM
COM
V+
V+
(This transformer is supplied within Commander Control Module
Box and is pre-wired and connected to 110V source of power)
Ignition Wire (RED)
Battery Wire (YELLOW)
Ground Wire (BLACK)
For Speaker Wiring
(Follow Stereo Manual)
NOTE: Wire colour identification may vary
between stereo manufactures.
(check with stereo manual)
Stereo (rear)
Wiring Harness
(plug into stereo)
CAUTION: The transformer input voltage may be 110 Volts
or 220 Volts. Make sure the switch on the side of the
transformer is in the correct position to allow for the
proper rated input power supply. Damage will
occur if this is incorrect.
Command II
Operating Instructions
www.saunacore.com