KD-AV41BT KD-AV31

JVC
KD-AV41BT
KD-AV31
MONITOR WITH DVD RECEIVER
INSTRUCTION MANUAL
MONITOR CON RECEPTOR DE DVD
MANUAL DE INSTRUCCIONES
JVC KENWOOD Corporation
Made for
~ iPod
DiPhone
© 2015 JVC KENWOOD Corporation
For KD-AV41 BT Region 1:
For KD-AV41 BT Region 1/KD-AV31 Region 1:
FCC WARNING
CAUTION
This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual . The user could lose
the authority to operate this equipment if an unauthorized change or modification
is made.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines in Supplement C to OET65. This equipment has very low levels of RF
energy that it deemed to comply without maximum permissive exposure evaluation
(MPE). But it is desirable that it should be installed and operated keeping the radiator
at least 20 em or more away from person's body (excluding extremities: hands,
wrists, feet and ankles).
FCC NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment may cause harmful interference to radio
communications, if it is not installed and used in accordance with the instructions.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radioffV technician for help.
A
I FCC 10: 2AB7S-KD-AV41 BT I
For KD-AV41 BT Region 4/KD-AV31 Region 4:
CLASS 1
LASER PRODUCT
The marking of products using lasers
The label is attached to the chassis/case and says that the component uses laser
beams that have been classified as Class 1. It means that the unit is utilizing laser
beams that are of a weaker class. There is no danger of hazardous radiation outside
the unit.
cAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure. In compliance with
Federal Regulations, following are reproductions of labels on, or inside the product
relating to laser product safety.
JVC KENWOOD Corporation
2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI,
TOKYO, JAPAN
(THIS PRODUCT COMPLIES WITH
DHHS RULES 21 CFR SUBCHAPTER J IN
EFFECT AT DATE OF MANUFACTURE.
Location : Bottom plate
2
Before Use
IMPORTANT
To ensure proper use, please read through this manual before using this product. It is especially
important that you read and observe WARNINGS and CAUTIONS in this manual. Please keep the
manual in a safe and accessible place for future reference.
A warning
Do not operate any function that takes your attention away from safe driving.
A caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the
sudden increase of the output level.
General:
• Avoid using the USB device or iPod/iPhone if it might hinder safety driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any
loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to
prevent a short circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the
moisture to evaporate.
-
.
-
I Basics
I Tuner
I iPod/iPhone (Only for KD-AV41 BT)
I Disc/USB
I External Components
I Bluetooth (Only for KD-AV41 BT)
I Sound/Display/Other Settings
I More Information
I Troubleshooting
I Specifications
Installation/Connection
3
••I
•II
•I
4
6
7
8
10
11
13
15
I
17
18
19
Remote control (RM-RK259):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with
the same or equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine,
fire or the like.
• Keep the battery out of reach of children and in original package when not used.
Dispose of used batteries promptly. If swallowed, contact a physician immediately.
3
How to read this manual
• Illustrations of KD-AV41 BT are mainly used for explanation.
The buttons .on the faceplate are used for explaining the
operations unless mentioned otherwise. However, if the
remote control has the same or similar button names, they
can also be used for the operations. For operations from the
remote control, see 11 Remote control (RM-RK259)". (-+ 5}
• [XX] indicates the selected items-or menu.
• {-+XX) indicates that references are available on the stated
page number.
• English indications are used for the purpose of explanation.
You can select the indication language from the [Settings/
General] menu. (-+14)
• Updated information (the latest Instruction Manual, system
updates, new functions, etc.) is available from <http://www.
jvc.net/cs/car/>.
ENGLISH
Basics
Faceplate
·
Attach
Monitor
@~~ ~
How to reset
Detach
~I 1 ,1~~~~~
KD-AV31
To
Dothis
Turn on the power
Press <.9/SOURCE.
(The buttons on the faceplate light up.)
• Press and hold to turn off the power.
Adjust the volume
Turn the volume knob.
Initial setting - Clock adjustment
Synchronizing the clock time with FM RBDS
Activate [RDS Clock Sync].(~ 6)
Adjusting the clock manually
1 Press <.9/SOURCE to turn on the power.
2 Press MENU to display the top menu screen.
3 Turn the volume knob to select [Settings], then press the knob to
display the setting menu.
4 Turn the volume knob to select l(U then press the knob to display
the [Settings/General] menu.
5 Turn the volume knob to select [Time], then press the knob.
6 Turn the volume knob to select the time format ([12 Hour] or
[24 Hour]), then press the knob.
7 Turn the volume knob to select [Adjust], then press the knob.
8 Turn the volume knob to adjust the hour, then press the knob.
9 Turn the volume knob to adjust the minute, then press the knob.
10 When [12 Hour] is selected in Step 6: turn the volume knob to
select AM or PM, then press the knob.
11 Press ~to exit.
• If no operation is done for about 10 seconds, the operation will be
canceled.
• To return to the previous layer, press v ~+~~.
Your preset adjustments
will also be erased.
Press the volume knob to mute the sound.
• Press again to cancel.
Select a source
• Press <.9/SOURCE repeatedly.
• Press MENU to display the top menu screen, and turn
the volume knob to select the source, then press the
knob.
Display the clock
Press and hold CLOCK.
Top menu screen operation
You can select the source or enter the
setting menu on the top menu screen.
Press MENU to display the top menu
screen, turn the volume knob to select the
item, then press the knob to confirm the
selection.
• If no operation is done for about 10
seconds, the operation will be canceled.
• To exit, press ~-
4
For KD-AV41 BT: [iPod] or [USB] ([iPod]
appears when the iPod/iPhone is connected.)
t
l
AUX
I
(I
Tuner
USB
01SC
*
BT Audio
.0.
Settings
Top menu screen
Basics
Remote control (RM-RK259)
Button
Operations
Button
Operations
Turns the power on/off.
~
Exits the menu.
MENU
Displays the top menu screen.
(<
Mutes/restores t he sound.
J/iJTI....IIJI>
Selects an item.
SOURCE
Selects a source.
ENTER
Confirms the selection.
LIST
VOLUME+/-
Adjusts the volume level.
Displays the item list for the
selected source.
~~~
Searches for radio stations
automatically. (Press)
How to install the battery
~~
CR2025
~4 0
~,9
If the effectiveness of the remote control decreases,
replace the batteries.
•
Stops playback.
~Ill
Starts/pauses playback.
CLOCK
Displays the clock.
DISP
Displays on-screen information.
DVDMENU
Displays the DVD d isc menu.
TOP MENU
Displays the DVD disc menu.
DVDAUDIO
Selects the audio language.
SUBTITLE
Selects the subtitle language.
ANGLE
Selects the view angle.
ZOOM
Magnifies the picture. (Not
available for sti ll picture p layback.)
GOTO
Enters direct search mode.
---
Searches for radio stations
manually. (Hold)
Selects a track. (Press)
Reverse search/forward search.
(Hold)
Returns to previous layer during
menu operation.
6 @@
9
~[ro;\
~~
• Aim the remote cont ro l directly at the remote sensor
on the faceplate.
• DO NOT expose the remote sensor to bright light
(direct sunlight or artificial lighting).
EQ
Selects the preset equalizer.
BASS BOOST
Activates/deactivates bass boost.
FNC
Displays the function menu for
the source.
0-9
Enters the number.
BAND
Selects the band.
CALIFORNIA, USA ONLY
This product contains a CR Coin Cell Lithium
Battery which conta ins Perchlorate Material special handling may apply. See www.dtsc.ca.gov/
hazardouswaste/perchlorate
5
ENGLISH
Tuner
!!!!!!~!- Band
LOCAL indicator
CD indicator
""""'!!!'!"!!__
Preset number
Station name (if acquired)
The frequency of the tuned-in station
Sound mode indicator (-+ 13)
!E
0
Tuner List
89.9o
19
105 .90
PA
89.9o
Gt
106.90
Bl
97.90
m 107.90
[Tuner List] menu screen
Tuner source screen
Other settings-Tuner function
Search for a station
Wh ile listening to a station ...
1 Press FNC to display the [Tuner function] menu.
2 Turn the volume knob to select the item to set (see the table below), then
press the knob to make a selection.
3 Press ~to exit.
Press <9/SOURCE repeatedly to select [Tuner].
2 Press BAND repeatedly to select the band.
• Selectable t uner band varies according to the selected [Radio Area] setting:
- [N America]/ [S America]: FM 1/ FM2/FM3/AM 1I AM2
3 Press V' ~+~~/~~~+~/"-to search for a station automatically.
• "Auto Seek" appears.
(or)
Press and hold V' ~+~~/~~~+~/"-repeatedly to search for a station manually.
1
• If no operation is done for about 10 seconds, the operation will be canceled.
Default: XX
• "Manual Seek" appears.
• The CD indicator lights up when receiving an FM stereo broadcast with sufficient
signal strength.
• To store stations, perform [Manual Store] or [Auto Store](-+ right column)
Manual
Store
Stores a station manually (up to 6 stations for each band).
While listening to a station you want to store, turn the volume knob to select a
preset number, then press the knob.
• 1he preset number, band, and "Stored OKI" appear.
Auto Store
Automatically searches and stores the 6 stations with the strongest signals for the
selected band.
• "Auto Store" appears.
Local Seek
ON:Tunes in only to the stations with sufficient signal strength. (LOCAL indicator
Select a stored station
1 Press LIST to display the [Tuner List] menu.
2 Turn the volume knob to select a preset number, then press the knob.
lights up.)
OFF: Deactivates the function.
• If no operation is done for about 10 seconds, the operation will be canceled.
• To exit, press ~.
Radio
Area
N America: For North/Central/South America, AM/FM intervals: 10kHz/200kHz.
S America: For some South American countries, AM/FM intervals:
10 kHz/50 kHz.
RDS Clock
Sync
6
ON: Synchronizes the clock time with FM RBDS.
OFF: Deactivates the function. Set the clock manually. (-+ 4)
iPod/iPhone {Only for KD-AV41 BT}
Song no./Total song number
Artwork (shown if the file contains
the artwork)
Song information
BASS indicator (-+ 13)
Playback status (~ :play/ II :
pause)/Piaying time/Total playing
time
Start playback
J
You cannot play video from the iPod/
iPhone.
iPod/iPhone (30-pin
connector models)
(commercially
available)
30-pin to USB cable
(accessory of iPod/
iPhone)*
iPod/iPhone
(Lightning connector
models)
(commercially
available)
D= o=o
o
@)+
~ ~~iY~
+@)
~
-IJ-o~il·o--7/.-;--.....IJ
.
.
USB 1nput termma 1
KS-U62 (optional
accessory)*
"USB Reading" appears, the source changes
to [iPod], and playback starts. (Current
control mode appears for 2 seconds.)
(-+ right column)
* Do not leave the cable inside the car
when not using it.
[List] menu screen
iPod/iPhone playback screen
To
Dothis
Play/pause
Press ~ / 11.
Other settings-iPod function
1 Press FNC to display the [iPod function] menu.
2 Turn the volume knob to select the item to set
Select the
control mode
Press and hold iPod MODE.
• To control music playback from this unit,
select [Head Unit Mode].
• To control music playback from the iPod/
iPhone, select [iPod Mode].
Select a song
Press v- ~+~~/~A. repeatedly.
Reverse/Fastforward
Press and hold v- ~+~~/~A..
Select a song
from the list
1 Press LIST to display the [List] menu.
(see the table below), then press the knob to
make a selection.
3 Press ~to exit.
• If no operation is done for about 10 seconds, the
operation will be canceled.
Default XX
Repeat*
OFF: Normal playback. (4 indicator
lights up.)
One: Functions the same as "Repeat One".
(~ indicator lights up.)
All: Functions the same as "Repeat All".
( ~ ind icator lights up.)
Random*
OFF: Normal playback. (4 indicator
lights up.)
Songs: Functions the same as "Shuffle
Songs". (~ indicator lights up.)
Albums: Functions the same as "Shuffle
A l bums" . ( ~ indicator lights up.)
Audiobook
Normal/Slow/Fast: Selects the speed
of audiobooks.
2 Turn the volume knob to select an
item, then press the knob.
1.Select [j l
2.Select category ([Piaylists]/ [Artists]/
[Aibums]/ [Genres]/ [Songs]/
[Composers]![Audiobooks]/
[Pod casts])
3.Select desired item.
• If no operation is done for about 10
seconds, the operation will be canceled.
• To return to the previous layer, press v- ~+~~.
• To exit, press ~.
7
----
* You cannot activate repeat mode and random
mode at the same time. ([OFF] is automatically
selected for the previously activated mode.)
ENGLISH
Disc/USB
Folder no./Total folder number
Start playback
Track/file no. I Total track/
file number
Track/file information
(MP3/WMA)
Disc
Source ([Disc] or [USB])
Sound mode indicator
BASS indicator (-t 13)
Playback status (..,.: playI II:
pause)/Piaying time/Total playing
time
(-t13)
Playback mode
Audio playback screen
CD/MP3/WMA
"DISC Reading" appears, t he source
changes to [Disc]. and playback starts.
• When the file list (the [list] menu) is
displayed, turn the volume knob to
select the file, then press the knob to
start playback.
• To eject a disc, press ]/ to open the
faceplate, then press ~ while the
power is turned on.
USB device
USB input
terminal
USB 2.0 cable*
(commercially
available)
=1==1~8
_ j ~ 1--~ @)
-r
..,_.....,.,..-_;...c
~+
Other settings-CO function/Media function
To
Do this
Play/pause
Press ... Ill.
1 Press FNC to display the [CD function] (CD) or [Media
function] (MP3/WMA) menu.
Select a track/
file
Press....., ~+~~/-.t /'. repeatedly.
2 Turn the vqlume knob to select the item to set (see the
table below), then press the knob to make a selection.
Reverse/Fastforward
Press and hold ....., ~+~~/-.. /'.,
Select a file
from a list
Press LIST to display [List] menu.
2 When the disc/device contains
different types of files: Press LIST
reP.eatedly to select the file type
3 Press !:>to exit.
• If no operation is done for about 10 seconds, the operation
will be canceled.
1
Default:.XX
Repeat
up.)
([)]).
mr::::J1ID
"USB Reading" appears, the source
changes to [USB]. and playback starts.
* Do not leave the cable inside the car
when not using it.
Folder: Repeats all files in the current folder.
(~ indicator lights up.)
3 Turn the volume knob to select an
item, then press the knob.
1.MP3/WMA: Select a folder (if
contained).
2.Select a track/file.
• If no operation is done for about
10 seconds, the operation will be
canceled.
• To return to the previous layer, press
'V 1+11.
8
All: Repeats all tracks/files.( ~ indicator lights up.)
One: Repeats current track/file. ( ~ indicator lights
Random
OFF: Normal playback.
ON: Randomly plays all tracks/files. ( ~ indicator
lights up.)
---
• You cannot activate repeat mode and random mode at
the same time. ([Off] is automatically selected for the
previously activated mode.)
If both the repeat mode and random mode are set to [OFF].
the unit repeats all tracks/files ( ~ indicator lights up.)
Disc/USB
w.
Playback information
• DVD Video: Title no./Chapter no./Piaying time
• VCD/MPEG1 /MPEG2: Playing time
i~ LIST
For DVDNCD/MPEG1/MPEG2: On-screen information is
displayed by pressing DISP on the remote control.
Video playback screen
Playback file type
) : Audio
liiiJ: Picture
8:Video
~
r~~
:~..,..:
J'j
USB
I
Songs
01 Song
-----
J'j
02 Song
J'j
03 Song
J'j
04 Song
------~--
[List] menu screen
DVDNCD/MPEG 1/MPEG2/JPEG
To
Do this
Play/pause
Press ~Ill.
Display the playback
information
Press DISP.
· To erase, press the button again.
Select a chapter/track/file
Press -v ~/ll+f .A repeatedly.
Press DVD MENU or TOP MENU.
Reverse/Fast-forward
Press and hold -v ~/ll+f .A.
• Each time you press the button, the search speed changes.
Display the disc menu
(DVD)
Search for a chapter/
title/scene directly
(DVD)
1 Press GOTO.
Select an item from the
disc menu/list
1
2
3
Various disc operations from the remote control (RM-RK259)
Press LIST.
---
DVD: Disc menu is displayed.
VCD w ith PBC: PBC menu is displayed.
2
• For VCD without PBC, the p layback is started from the
1st track.
3
• Each time you press the button,
the target item switches between
chapter, title, and time.
Use the number buttons to select a
chapter/title/scene.
Press ENTER.
MPEG 1/MPEG2/JPEG: [List] menu is displayed.
When the disc/device contains different types of files:
Select the track from
PBC menu (VCD)
Press LIST repeatedly to select a playback file type
(lE]1: video file/[~] : picture file).
Turn the volume knob to select an item, then press the
knob.
Press LIST to display the PBC menu,
then press the number button to select
a track.
Select audio language
Press DVD AUDIO repeatedly.
Select subtitle
language
Press SUBTITLE repeatedly.
Select view angle
Press ANGLE repeatedly.
Magnify the picture
(except for JPEGs)
Press ZOOM repeatedly.
Repeat the procedure until playback starts.
• If no operation is done for about 10 seconds, the operation
will be canceled.
• To return to the previous layer, press -v ~.
--'-----
• DVDNCD: To exit, press ~.
Continued on the next page
9
ENGLISH
External Components
Disc/USB
Use a portable audio player (AUX)
Other settings-DVD function/VCD function/Media function
Press FNC to display the [DVD function] (DVD), [VCD function] (VCD), or
[Media function] (MPEG 1/MPEG2) menu.
2 Turn the volume knob to select the item to set (see the ta ble below), then
press the knob to make a selection.
3 Press ~to exit.
1
Sound mode indicator (-+ 13)
3.5 mm stereo mini plug
(commercially available)
• If no operation is done for about 10 seconds, the operation will be canceled.
Default: XX
Repeat
Auxiliary input jack
Portable audio
player
OFF: Normal playback.
Ch: Repeats current chapter.
Tt: Repeats current title.
1 Connect a portable audio player (commercially available).
VCD
All : Repeats all tracks/files.
One: Repeats current track/file.
2 Press C)/SOURCE repeatedly to select [AUX].
3 Turn on the portable audio player and start playback.
MPEG1/MPEG2
All : Repeats all tracks/files.
One: Repeats current track/file.
Folder: Repeats all files in the current folder.
DVD
Q\
~
Selects the audio language.
AUX source screen
Use a 3-core plug head stereo mini plug for optimum audio output.
Use a rear view camera
Selects the subtitle language.
To use a rear view camera, the REVERSE GEAR SIGNAL wire connection is requi red.
For details, see "Installation/ Connection". (-+ 20)
Selects the view angle.
16:9 I 4:3: Selects the aspect ratio.
When a rear view camera is connected, the rear
view screen is displayed when you shift the gear
to the reverse (R) position.
• Check the safety of your surroundings with
your eyes before backing up.
Stereo I Left I Right: Selects the audio channel.
PBC
ON: Activates the PBC function.
OFF: Deactivates the PBC function.
• When PBC is activated, repeat mode is automatically deactivated
([Off]).
VI
Qi
(i::
.......
VI
u
VI
-o
Rear view screen
+08 (04): Adjusts the brightness.
Brightness
-00 -
Contrast
-00 -. +08 (04): Adjusts the contrast.
Color
-00 -
+08 (04): Adjusts the colors.
Restores the default settings.
10
Blueto oth {Only for KD-AV41 BT)
Information for using Bluetooth®devices
Connecting a Bluetooth device
0 Bluetooth®
To use a Bluetooth device (mobile phone or audio player), pair the device and the
unit. Pairing allows Bluetooth devices to communicate with each other.
• Use a Bluetooth device compatible with Bluetooth 3.0.
• You can pair the device and the unit using SSP (Secure Simple Pairing) which on ly
requires confirmation.
• Once a device and the unit are paired, the unit is registered on the device. When
you next use the device with the unit, you can connect the device and the unit by
selecting from the registered device list on your device.
• One device can be connected at a time .
Bluetooth is a short-range wireless radio communication technology for mobile
devices such as mobile phones, portable PCs, and other devices. Bluetooth devices
can be connected without cables and communicate with each other.
Notes
• While driving, do not perform complicated operations such as dialing numbers,
using the phone book, etc. When you perform these operations, stop your car in a
safe place.
• Some Bluetooth devices may not connect to this unit depending on the Bluetooth
version of the device.
• This unit may not work for some Bluetooth devices.
• Connecting conditions may vary depending on your environment.
• For some Bluetooth devices, the device is disc~mnected when the unit is turned
off.
Pairing a Bluetooth device manually
1 Turn on the Bluetooth function on your Bluetooth device .
2 Search for the unit ("JVC unit" ) from your Bluetooth device.
3 Confirm the request on the device.
Pairing and connection are established. "Connect OK" appears.
• "\.)) "appears when the Bluetooth mobile phone is connected.
• "})) "appears when the Bluetooth audio player is connected.
About mobile phones compatible with Phone book Access Profile (PBAP)
If your mobile phone supports PBAP, you can display the following items on the
touch panel screen when the mobile phone is connected.
• Phone book (up to 1000 entries)
• Dialed calls, received calls, and missed calls (up to 10 entries in total)
Disconnecting the device
Turn off the ignition switch.
Checking the information about the paired device
Select [BT Info] on the [Settings/Biue tooth] menu. (-+14)
Continued on the next page
11
ENGLISH
Bluetoo th
~ 012
BASS indicator
(~ 13)
Phone screen
Voice dialing screen
*
flT AudiO
\. ':
-
.... ~~
A'l
10:36
Song Name
J
lrJ.
Art1~t
11':'1 ...
Track information
Name
!Ill' .
.
A S
Br£j
ROCK
Playback status
06.32
II• o2 32
(IJil>: play/ 11 : pause)/ II.!:=== =
Playing time/Total Bluetooth audio playback screen
playing time
Sound mode
indicator
(~ 13)
Bluetooth audio player
Bluetooth mobile phone
To
Do this
To
Do this
Make a call
1 Press\. I ~-
Start Bluetooth audio
player
Press <9/SOURCE repeatedl y to
select [BT Audio].
Play/paus e
Press ... Ill.
Select a track
Press V' ~+~~/~A repeatedly.
Reverse/F ast-forwar d
Press and hold
Select an item from the
track list
Press LIST to display the track
list.
2 Turn the volume knob to select
an item, then press the knob.
Repeat the procedure until
The phone screen is displayed.
2 Press V' ~+~~,turn the volume knob to select a method to make a
3
call ([(.OJ: from the calls history/[: H ]: from the phone book),
then press the knob.
Turn the volume knob to select the target, then press the knob
to make a call.
• To ret urn to the previous layer, press V' ~+~~.
Receive a call
Press the volume knob when a call comes in.
Use voice dialing
1 Press and hold\,. 1 ~to display the voice dialing screen.
• You can also display the voice dialing screen by selecting [f,J as
the method to make a call on the phone screen.
2 Press the volume knob to activate voice recognitio n function.
"Please speak after the beep" appears and the beep sounds.
3 Say the name of the person you want to call.
Reject a call/
End a call
Press!::>.
Switching between
handsfree mode
and phone mode
While talking, press FNC.
Each time you press the button, 'Transfer!" appears and talking
method is switched between handsfree mode and phone mode.
12
V'
~+~~/~A.
1
playback starts.
If no operation is done for about
10 seconds, the operation wil l be
canceled.
• To return to the previous layer,
press V'~+~~.
• To exit, press !::>.
Sound/D isplay/Ot her Settings
Q Settings/AudiO
Bass
. .1))
AM
10:36
-4 03
•I
Middle
0
Treb le
*
Fader
Balance
[Settings/Audio] menu
Only for KD-AV31. For KD-AV41 BT, operate on the [Settings/Audio]
menu, or from the remote control (RM-RK259).
Select a preset equalizer (EQ)
Activate the bass boost
Press EQ repeatedly to select a preset sound mode - [Flat] (default)/[Pop)/
[User)/[Techno)/[Rock)/[Ciassic)/[Jazz)/[Optimal]. (Corresponding sound
mode indicator lights up.)
Press BASS BOOST. (BASS indicator lights up.)
• To cancel, press the button again.
Only for KD-AV41 BT:
You can also activate/deactivate the bass boost on the [Settings/Audio] menu.
1 Press MENU to display the top menu screen.
2 Turn the volume knob to select [Settings], then press the knob to display the
setting menu.
3 Check that [..1))1 ([Settings/Audio]) is selected, then press the knob.
4 Turn the volume knob to select [Bass Boost], then press the knob.
5 Turn the volume knob to select [ON] (to activate) or [OFF] (to deactivate),
then press v- ~+~~.
6 Press ~to exit.
Store your own sound settings
1 Press EQ repeatedly to select [User].
2 Press MENU to display the top menu screen.
3 Turn the volume knob to select [Settings], then press the knob to display the
setting menu.
4 Check that [..1))] ([Settings/Audio]) is selected, then press the knob.
5 Turn the volume knob to select the item to set ([Bass)/[Middle)* /[Treble]),
then press the knob.
6 Turn the volume knob to adjust the value, then press v- ~+~~.
7 Repeat steps 5 and 6 to adjust the value for other settings.
8 Press ~to exit.
The setting is stored to [User] in EQ.
.
• If no operation is done for about 10 seconds, the operation will be canceled.
• To return to the previous layer, press v- ~+~.
Change the display brightness (Dimmer)
• If no operation is done for about 10 seconds, the operation wil l be canceled.
• To return to the previous layer, press v- ~+~~.
Press and hold DIMMER repeatedly to select [Dimmer Low] or [Dimmer High].
* Only for KD-AV41 BT.
Continued on the next page
13
ENGLISH
Sound/Display/Other Settings
(J
Settmgs/Aud10
..,l)
Bass
0
Treble
AM
~
03
10:36
.. I
Middle
*
Fader
Balance
[Settings/General] menu
[Settings/Audio] menu
[Settings/Biuetooth] menu
Default: XX
Change the general settings/check information on the [Settings] menu
Settings/Audio (..1)))
1 Press MENU to display the top menu screen.
2 Turn the volume knob to select [Settings], then press the knob to display the
setting menu.
3 Turn the volume knob to select the category (1.1)): [Settings/Audio]/
0: [Settings/Generai]JC): [Settings/Biuetooth]), then press the knob.
4 Turn the volume knob to select the item to set (see the table on the right
column), then press the knob.
5 Turn the volume knob to change the setting, then press the knob.
Bass*l
-15 -
+ 15 (00): Adjusts the sound elements of the bass tone.
Middle*l *2
-15 -
+ 15 (00): Adjusts the sound elements of the middle tone.
Treble*!
-15 -
+15 (00): Adjusts the sound elements of the treble tone.
Fader
R12 -
F12 (00): Adjusts the front and rear speaker output balance.
Balance
L12 -
R12 (00): Adjusts the left and right speaker output balance.
Bass Boost*2
ON/OFF: Activates or deactivates the bass boost.
Settings/General ((I)
• If no operation is done for about 10 seconds, the operation will be canceled.
• To return to the previous layer, press v- ......
• To exit, press !::>.
Beep
ON/OFF: Activates or deactivates the keypress tone.
Time
12 Hour/ 24 Hour: Selects time format.
Adjust: Adjusts the clock.
Language
English/Espanol: Selects the text language used for on-screen
information.
Settings/Biuetooth <0)*2
Sync
Phonebook
ON/OFF: Activates or deactivatesthe synchronization of the phonebook in
the connected mobile phone with the unit.
BT Info
Displays the information about the connected Bluetooth device (device name,
phone name, Bluetooth version, and mac address).
*1 Adjustable only when [User] is selected as the sound mode.
*2 Only for KD-AV41 BT.
14
More Information
About discs .
• Playable discs:
Recording
format, file type,
etc.
DVD
• DTS sound cannot be reproduced
or emitted from this unit.
DVD Video*l
DVD Recordable/
Rewritable (DVD-R/-RW*2,
+R/+RW*3)
• DVD Video: UDF bridge
• DVD Video
• MPEG1/MPEG2
• JPEG
• MP3/WMA
• MPEG1/MPEG2/JPEG/MP3/WMA:
ISO 9660 Ieveil, level 2, Romeo,
Joliet
Dual Disc
DVD side
CDNCD
• VCD (Video CD)
• Audio CD/CD-DA
CD Recordable/Rewritable
(CD-R/-RW}
• ISO 9660 level 1, level 2, Romeo,
Joliet
• VCD (Video CD)
• CO-DA
• MPEG1/MPEG2
• JPEG
• MP3/WMA
*1 DVD Video Region Code:
North America area: 1
South America area: 4
*2 DVD-R recorded in multi-border format are also
playable (except for dual layer discs). DVD-RW dual
layer discs are not playable.
*3 It is possible to play back finalized +R/+RW (Video
format only) discs. "DVD" is selected as the disc type
when a +R/+RW disc is loaded. +RW double layer
discs are not playable.
• Unplayable discs:
- DVD-Audio, DVD-ROM (data), DVD-RAM, DVD+R/
DVD+RW recorded in the DVD-VR/DVD+VR format,
DTS-CD, SVCD (Super Video CD), CD-ROM, CD-I
(CD-I Ready), etc.
- Discs that are not round.
- Discs with coloring on the recording surface or
discs that are dirty.
- Recordable/ReWritable discs that have not been
finalized.
- 3 inch discs. Attempting to insert using an adapter
may cause malfunction.
• Dual Disc playback: The Non-DVD side of a
"Dual Disc" does not comply with the "Compact Disc
Digital Audio" standard. Therefore, the use of the
Non-DVD side of a Dual Disc on this product cannot
be recommended.
About USB devices
• This unit can play MPEG 1/MPEG2/JPEG/MP3/WMA
files stored on a USB mass storage class device.
• You cannot connect a USB device via a USB hub or
Multi Card Reader.
• Connecting a cable whose total length is longer than
5 m may result in abnormal playback.
• The maximum number of characters for:
- Folder names: 50 characters
- File !)ames: 50 characters
- MP3/WMA Tag: 50 characters
• This unit can recognize a total of 65 025 files, 255
folders (255 files per folder including folder without
unsupported files), and of 8 hierarchies.
• This unit cannot recognize a USB device whose
rating is other than 5 V and exceeds 1 A.
About files
• Playing MPEG 1/MPEG2 files:
- This unit can play back MPEG 1/MPEG2 files with
the extension code <.mpg> or <.mpeg>.
- The stream format should conform to MPEG
system/program stream.
- Audio streams should conform to MPEG 1 Audio
Layer-2, Dolby Digital or MP3.
- The maximum bit rate for video signals (average) is
4 Mbps.
- Files encoded in the interlaced scanning mode
may not be played back correctly.
• Playing JPEG files:
- This unit can play back JPEG files with the extension
code <.jpg>.
- This unit can play back JPEG files that are at 32 x 32
to 4 096 x 2 840 resolution.
It may take time to display the file depending on its
resolution.
- This unit can play back baseline JPEG files.
Progressive JPEG files or lossless JPEG files cannot
be played.
Continued on the next page
15
ENGLISH
More Information
• Playing MP3/WMA files:
- This unit can play back files with the extension
code <.mp3> or <.wma> (regardless of the letter
case-upper/lower).
- This unit can play back the files meeting the
conditions below:
• Bit rate: 32 kbps- 320 kbps
• Sampling frequency: 8 kHz- 48 kHz
- This unit can show ID3 Tag Version
1.0/1.1/2.2/2.3/2.4 (for MP3).
- This unit can also show WMA Tag.
- This unit can play back files recorded in VBR
(variable bit rate).
- Files recorded in VBR have a discrepancy in elapsed
time indication.
- This unit cannot play back the following files:
• MP3 files encoded with MP3i and MP3 PRO
format.
• MP3 files encoded with Layer 1/2.
• WMA files encoded with lossless, professional,
and voice format.
• WMA files which are not based upon Windows
Media® Audio.
• WMA files copy-protected with DRM.
About iPod/iPhone
• Made for
- iPod touch 4th generation
- iPod touch 3rd generation
- iPod touch 2nd generation
- iPod classic
- iPod nano (6th Generation)
- iPod nano (5th Generation)
- iPod nano (4th Generation)
- iPod nano (3rd Generation)
- iPhone 6S Plus
- iPhone 6S
- iPhone 6 Plus
- iPhone 6
- iPhone SS
- iPhone SC
- iPhone 5
- iPhone 4S
- iPhone 4
- iPhone 3GS
- iPhone 3G
• The song order displayed on the selection menu of
this unit may differ from that of the iPod/iPhone.
• Video playback is not compatible with this unit.
16
Maintenance
Cleaning the unit: Wipe off dirt on the faceplate
with a dry silicon or soft cloth.
Cleaning the connector: Detach the faceplate and
clean the connector gently with a cotton swab,
being careful not to damage the connector.
~JL 0~
Connector (on the reverse side of
the faceplate)
Handling discs:
• Do not touch the recording surface of the disc.
• Do not stick tape etc. on the disc, or use a disc
with tape stuck on it.
• Do not use any accessories for the disc.
• Clean from the center of the disc and move
outward.
• Clean the disc with a dry silicon or soft cloth. Do
not use any solvents.
• When removing discs from this unit, pull them
out horizontally.
• Remove burrs from the center hole and disc edge
before inserting a disc.
Troubleshooting
• Adjust the volume to the optimum level.
• Check the cords and connections.
"PARKING is not enabled. No
video while driving." appears
and no playback picture is
shown.
Parking brake is not engaged.
The unit does not work at all.
Reset the unit.(~ 4)
The remote control does not
work.
Replace the battery.
Playback source cannot be
selected.
The source is not ready. Insert a disc or connect a device
beforehand.
• Recordable/Rewritable discs
cannot be played back.
• Tracks on the Recordable
Rewritable discs cannot be
skipped.
• Insert a finalized disc.
• Finalize the discs with the component which you used
for recording.
"DVD Region Error" appears and
DVD-Video does not play.
Insert a disc with the correct Region Code.
Playback order is not as
intended.
The playback order is determined by the file name (USB) or
the order in which files were recorded (disc).
Elapsed playing time is not
correct.
The elapsed playing time depends on the recording process
used.
Playback does not start or the
track is skipped.
• Check whether the track is a playable format.
(~ 15)
• Record the tracks using a compliant application on the
appropriate discs.
• Add appropriate extension codes to the file name.
a long time to read
• Radio reception is poor.
• Static noise while listening to
the radio.
• Connect the antenna firmly.
• Pull the antenna out all the way.
The iPod/iPhone does not turn
on or does not work.
• Check the connection between this unit and the iPod/
iPhone.
• Check whether the control mode is appropriate.
(~ 7)
• Detach and reset the iPod/iPhone using hard reset.
is distorted.
Deactivate the equalizer either on this unit or the iPod/
iPhone.
sound quality is poor.
• Reduce the distance between the unit and the Bluetooth
mobile phone.
• Move the car to a place where you can get a better signal
reception.
The sound is interrupted or
skipped while using a Bluetooth
audio player.
connected audio player
be controlled.
• Reduce the distance between the unit and the Bluetooth
audio player.
• Turn off, then turn on the unit.
(When the sound is not yet restored) connect the player
again.
• Check whether the connected audio player supports
AVRCP (Audio Video Remote Control Profile).
Search from the Bluetooth device again.
unit does not pair with the
device.
u ... ,, ............ h
• Turn off, then turn on the Bluetooth device.
• Disconnect the device currently connected.
* Only for KD-AV41 BT.
• Do not use too many hierarchical levels and folders.
• Reload the disc or reattach the USB device .
• Check whether the connected device is compatible with
this unit and ensure the files are in supported formats.
(~ 15)
• Reattach the device.
17
ENGLISH
Specifications
Bluetooth section*
Monitor section
Picture Size (W x H)
3.0 inch QVGA display
Technology
Bluetooth 3.0
Drive System
TFT active matrix system
Frequency
2.4 GHz- 2.4835 GHz
Number of Pixels
320 pixels x 240 pixels
Aspect Ratio
16:9 (wide)
Back Lighting
LED
DVDsection
Audio Decoder
MP3/WMA
Video Decoder
MPEG1/ MPEG2
Wow & Flutter
Below Measurable Limit
Frequency Response
96kHz Sampling: 20Hz- 20 000 Hz
48 kHz
20 Hz - 20 000 Hz
Signal to Noise Ratio
80 dB
Dynamic Range
90 dB
DISC Format
DVD-Video/DVD-VR/DVD-R/
DVD-RW /+R/+RW /VIDEO-CD/
CD-DA
Sampling Frequency
Output Power
Maximum
Communication
Line of sight approx. 10m (32.8 ft)
Audio Codec
SBC
Profile
HFP (Hands Free Profile) 1.6
A2DP (Advanced Audio Distribution
Profile) 1.3
AVRCP (Audio/Video Remote Control
Profile) 1.5
PBAP (Phone Book Access Profile)
1.1.1
Frequency Range
(Frequency Step)
48 kHz/96 kHz
USB Interface section
+4 dBm (MAX), 0 dBm (AVE),
Power Class 2
With channel interval set
to 50 kHz: 87.5 MHz -108.0 MHz
With channel interval set
to 200kHz: 87.9 MHz -107.9 MHz
~V /75 0)
Frequency Range
(~~~q~-~~~¥?~~PX ___ -·- _________ .· · · --·· · · · ··selectivity
Video
Video Output Level
(RCA jacks) NTSC
1 Vp-p I 75 0
------~------ - ----~~---------~~-~.~.~-------·
Audio
Maximum Power (Front 50 W x 4
& Rear)
Full Bandwidth Power
(Front & Rear)
20Wx4
(4 0, 14.4 V, at less than 1 % THD)
Preout Level (V)
2.5 V/10 kO
Preout Impedance (0)
1 kO
Speaker Impedance (0)
4 0- 8 0
Equalizer
For KD-AV41 BT: 3 Band
For KD-AV31: Bass/Treble
Usable Sensitivity (SIN:
30 dB Dev 22.5 kHz)
9 dBf (0.8
Quieting Sensitivity
(50 dB)
14dBf(1.8 ~V/75 0)
Operating Voltage
14.4 V(10.5 Vto 16 V)
10 A
182 mm x 52 mm x 167 mm
(Main Unit Installation size)
General
USB 2.0 Full Speed
Compatible Devices
Mass storage class
File System
FAT 16/32
Frequency Response
(±3.0 dB)
35Hz-14kHz
Maximum Current
Consumption
Maximum Power
Supply Current
DC 5 V ==-= 1.0 A
Stereo Separation
42 dB
Installation Dimensions
(W x H x D)
Audio Decoder
MP3/WMA
-
55 dB
Usable Sensitivity
USB Standard
Video Decoder
530kHz- 1 700kHz (10kHz)
Operational
_Temperature Range
-~-------···-~~----~---~---------------------
MPEG1/MPEG2/JPEG
Weight (Main unit)
0 octo +40 oc
1.2 kg
Subject to change without notice.
* Only for KD-AV41 BT.
18
Installation/Connection
A warning
• The unit can only be used with a 12 VDC power supply, negative ground .
• Disconnect the battery's negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis
or Ground wire (black) to prevent a short circuit.
• Insulate unconnected wires with vinyl tape to prevent a short circuit.
• Be sure to ground this unit to the car's chassis again after installation.
1
@) Do the required wiring.(~ 20)
Bend the appropriate tabs
to hold the sleeve firmly
in place .
A caution
• For safety's sake, leave wiring and mounting to professionals. Consult the car
audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal parts of
this unit during and shortly after use of the unit. Metal parts such as the heat
sink and enclosure become hot.
• Do not connect the 8 wires of speaker to the car chassis, Ground wire
(black), or in parallel.
• Mount the unit at an angle of less 30°.
• If your vehicle wiring harness does not have the ignition terminal, connect
Ignition wire (red) to the terminal on the vehicle's fuse box which provides 12
VDC power supply and is turned on and off by the ignition key.
• After the unit is installed, check whether the brake lamps, blinkers, wipers,
etc. on the car are working properly .
• If the fuse blows, first make sure the wires are not touching car's chassis, then
replace the old fuse with one that has the same rating.
r-----------------------~
I
I
I
I
:~ :
I
I
I
I
l 0°-30~ l
'-----------------------'
When installing without the mounting sleeve
Bmm
Flat head screws (supplied ((])): MS x 8 mm) or \"'--...
round head screws (not supplied: MS x 6 mm) \., t4>-....__
6mm
...........
~ ~
'-...
~(} ~mD
Basic procedure
1
2
3
Remove the key from the ignition switch, then disconnect
the 8 terminal of the car battery.
Connect the wires properly.
See "Wiring connection".(~ 20)
How to remove the unit
Install the unit to your car.
*1
See "Installing the unit (in-dash mounting)".(~ right column)
4
5
Connect the 8 terminal of the car battery.
Reset the unit.(~ 4)
*2
I Check the supplied parts for installation beforehand.(~ 21)
Face t he side with the protrusion
inside when inserting t he extraction
keys.
If the panel opening of your vehicle is
too small to fit the unit, trim the upper
and lower sides of the panel opening.
Cont inued on the next page
19
ENGLISH
Installation/Connection
Wiring connection
Light blue/Yellow
STEERING
WHEEL
REMOTE
CONTROL
Fuse (15 A) Purple/White
Audio output (Rear)
IREVERSE
GEAR
output*
* Video is not output for
the video output terminal
when the source is
[Tuner] or [AUX].
Il
___ _
8
I
PARKING
BRAKE
....
To reverse lamp (required when using a rear view camera)
SIGNAL
Light Green
~~-- G)
To use the steering wheel remote control feature, an exclusive remote
adapter (not supplied) matching your car is required.
To the vehicle's parking brake detection switch harness.
'~Onlyfu r KD-AV41 BT: Connect the microphone for Bluetooth (_.
l
I
~~
21 ).
Antenna cord
Antenna termmal
0
- -- - - ----- - --- -- --- --- -----L-----------------------------------------------------------~
'-----.----..--- To the power control terminal when using an optional power amplifier, or to the antenna control
terminal in the vehicle (150 mA max)
Ignition switch
Change the FUSE location to switch ACC
and B+ pin location on the ISO connector.
@=®
+-+~
att~e~ry~w~i~re~)-------------------~-B_
llo~w~(~B~
L-~Y~e~
1....-....;:;.....1
Black (Ground wire)
White EB I White/Black 8: To front speaker (left)
Battery
Gray EB I Gray/Black 8: To front speaker (right)
Green EB I Green/Black 8: To rear speaker (left)
'I
Purple EB I Purple/Black 8: To rear speaker (right)
~----------------------------------------------------------------------------------------------
20
Installation/C onnection
Connecting microphone for Bluetooth
(Only for KD-AV41 BT)
Parts list for installation
Connect the microphone (Q)) to the MIC terminal.
• To install the microphone, peel off the adhesive tape,
fix it on the installation position, then adjust the
direction of the microphone to face the driver. After
installing, fix the microphone cable to the car with
clamps (commercially available).
®
Faceplate/Faceplate case
®
Extraction keys
®
Mounting sleeve
®
Rubber cushion
©
Trim plate
®
Mounting bolt
-M5x12mm
@ Powercord
CD
Flat head screws
-M5x8mm
®
Q) Microphone*
--
~~()==:=::::::
7~==-,
~
r-----VI-,d-eo_O_u_t------------------~~~
®®
L
~®
Rear Camera In
~ : : : :II
t:l.!; ; ~= · :;;!LJI--
8
Speaker cord
• "DVD Logo" is a trademark of DVD Format/Logo
Licensing Corporation registered in the US, Japan
and other countries .
• Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol are
trademarks of Dolby Laboratories .
• Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation
in the United States and/or other countries.
• This item incorporates copy protection technology
that is protected by U.S. patents and other
intel lectual property rights of Rovi Corporation.
Reverse engineering and disassembly are
prohibited .
• "Made for iPod," and "Made for iPhone" mean that
an electronic accessory has been designed to
connect specifically to iPod, or iPhone, respectively,
and has been certified by the developer to meet
Apple performance standards. Apple is not
responsible for the operation of this device or its
compliance with safety and regulatory standards.
Please note that the use of this accessory with
iPod, or iPhone may affect wireless performance.
• iPhone, iPod, iPod classic, iPod nano, and iPod
touch are trademarks of Apple Inc., reg istered in
the U.S. and other countries .
• Lightning is a trademark of Apple Inc.
• The BluetoothGD word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by JVC KENWOOD Corporation is
under license. Other trademarks and trade names
are those of their respective owners.
* Only for KD-AV41 BT.
21
ENGLISH
.JVC
U.S.A.
JVC AMERICAS CORP.
TO OUR VALUED CUSTOMER
THANK YOU FOR PURCHASING THIS JVC PRODUCT.
WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE.
NEED HELP ON HOW TO HOOK UP?
NEED ASSISTANCE ON HOW TO OPERATE?
NEED TO LOCATE A JVC SERVICE CENTER?
LIKE TO PURCHASE ACCESSORIES?
JVC IS HERE TO HELP!
TOLL FREE: 1 (800)252-5722
http ://www.jvc.com
Remember to retain your Bill of Sale for Warranty Service.
Do not attempt to service the product yourself
Caution
To prevent electrical shock, do not open the cabinet.
There are no user serviceable parts inside.
Please refer to qualified service personnel for repairs.
JVC
LIMITED WARRANTY
ONLY FOR PRODUCT PURCHASED IN U.S.A.
JVC Americas Corp. (JVC) warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL
RETAI L PURCHASER to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original purchase for
the period shown below. ("The Warranty Period")
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND IN THE
COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective within the warranty period, JVC wil l repair or replace defective parts with new or rebuilt equivalents at no
chargeto the original owner. Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized
service centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All products may be brought to aJVC
authorized servicecenter on acarry-in basis. Color televisions with ascreen size of 37"class or greater qualify for in-home service. In such
cases, atechnician will come to your home and either repair the TVthereor remove and return it if it cannot be repaired inyour home.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Please do not return your product to the retailer. Instead, return your product to the JVC authorized service center nearest you. If shipping the
product to theservice center, please be sureto package it carefully, preferably in the original packaging, and include a brief description of
the problem(s) and a copy of the proof of purchase to verify purchase date. Please cal l t-800-252-5722 to locatethe nearest JVC authorized
service center. Service locations can also be obtained from our website http://www.jvc.com. If your product qualifies for in-home service, the
service representative will require clear access to the product.
If you haveany questions concerning your JVC Product. please contact our Customer Care Center at 800-252-5722
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence. misuse, faulty installation, lack of
reasonable care, or if repaired or serviced by anyone other than aservice facility authorized by JVC to render such service. or if affixed to
any attachment not provided with the products, or if the model or serial number has been altered, tampered with, defaced or removed;
2. Initial installation, installation and removal from cabinets or mounting systems
.
3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act ol God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. User Removal Memory Devices/Video Pick-up Tubes/CCD Image Sensors are covered for 90 days from thedate of purchase;
7. Accessories;
8. Batteries (except that Rechargeable Batteries are covered for 90 days fromthe date of purchase);
9. Products used for commercial purposes, including, but not limited to rental.
10. Loss of data resultant from malfunction of hard drive or other data storage device;
Thereareno express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OFMERCHANTABILITY, IS LIMITED TO
THEDURATION OF THE EXPRESS WARRANTY HEREIN. JVC SHALL NOTBE LIABLE FOR ANY LOSS OF USE OF THEPRODUCT,
INCONVENIENCE, OR ANY OTHER DAMAGES, WHETHERDIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT
LIMITATION, DAMAGE TO TAPES, RECORDS ORDISCS) RESULTING FROM THE USE OFTHIS PRODUCT, OR ARISINGOUT OF ANY
BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES. INCLUDI NG THE WARRANTIES OF MERCHANTABILITYAND
FITNESS FOR PARTICULARPURPOSE, ARELIMITED TO THE WARRANTYPERIOD SET FORTHABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts, so
these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
JVC AMERICAS CORP.
1700 Valley Road, Wayne, New Jersey 07470
http://www. jvc.com
PRODUCT REGISTRATION
We suggest that you register your product since it will enable us to contact you
directly if it is ever necessary to correct a safety related condition in your product.
You can register at www.register.jvc.com
Please note that failure to register does not diminish any of your rights during the
warranty period.
BT-50004-1 (0313)
REFURBISHED PRODUCTS CARRY ASEPARATE WARRANTY. THIS WARRANTYDOES NOT APPLY. FOR DETAIL OF REFURBISHED PRODUCT
WARRANTY, PLEASE REFER TO THEREFURBISHED PRODUCT WARRANTY INFORMATION PACKAGED WITHEACHREFURBISHED PRODUCT
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of thecabinet. Retai n this information for future
reference.
Model No.:
Serial No.:
Purchase date:
Name of dealer:
Printed in China
CANADA
.JVC
JVC CANADA INC.
WARRANTY
GARANTIE
Warranty applies only to PRODUCT distributed in Canada by JVC Canada Inc.
JVC CANADA INC. (hereafter called "JVC") gives the following express warranty lor each new JVC product distributed in
Canada by JVC and sold by an authorized JVC dealer. JVC warrants that this JVC product is free, under normal use and
maintenance, from any defects in material and workmanship subject to the following terms and conditions:
La garantls' applique seulement aux PRODUITS distrlbues au Canada par JVC Canada Inc.
JVC CANADA INC. ( ci-apres appele "JVC") enonce Ia garantie expresse suivante pour tout nouveau produit JVC distribue
au Canada par JVC et vendu par un detaillant JVC autorise. JVC vous garantit que ce produit est degage, so us utilisation et
entretien normal, de tout delaut materiel et de fabrication so us reserve des modalites et conditions suivantes:
1. To Obtain Warranty Service:
(a) JVC product requiring service must be presented together
with proof of purchase.
(b) The JVC product must be brought in for service to an
authorized JVC Service Centre.
3. Standards:
If any defects should be found in aJVC product within the
applicable terms. necessary repairs shall be made at no cost to
the purchaser for parts or labour when JVC acknowledges that
such detects are due to faulty material or workmanship.
1. Pour obtenir un service de garantie:
(a) Les produits JVC n~cessitant un service doit etre presentee
avec Ia prevue d'achat
(b) Le produit JVC do it etreapport€ pour service chez un centre
deservice JVC autorise.
2. Limitation:
This Warranty shall not apply to:
(a) Repair or replacement of any cabinets, batteries, plates,
connection cords, antennas, dust covers, knobs, speaker
grills, speaker cones, projection screens, projection screen
savers, and all accessories.
(b) Any defects caused or repairs required as aresult of
misuse, abusive operation, negligence, improper use and/or
insufficient care.
(c) Any defect caused or repairs required as aresult of not
following the instructions in the operation manual.
(d) Any JVC product tampered with, adjusted or repaired by
any party other than JVC or authorized JVC Service Centre
personnel.
(e) Any JVC products on which the serial number has been
defaced, modified or removed.
(I) Maintenance, cleaning or periodic check-up
(g) Conversion to foreign or domestic voltage or frequency.
(h) Any JVC product without the Canadian Electrical Safety
Regulations ID.
(i) Any JVC products used for commercial or institutional,
rental, or display purposes.
Parts ...... 1year (except video head- 90 days)
Labour ... 90 days
(j) Any JVC product which has been resold and no longer owned
by the original purchaser.
(k) Product purchased from ·outside Canada", "bankruptcy· or
'liquidator·.
(I) Any defects caused by fire, flood, lightning, power surge, or
other events beyond the control of JVC.
(m) FOR AUTO PRODUCTS
Warranty does not cover elimination of car static or electrical
interferences. cleaning of head. adjustments. or labour cost
lor the removal or reinstallation of the unit for repair.
4. Exclusion of All Other Express Warranties:
This warranty constitutes the entire express warranty given by
JVC for JVC products and nodealer or service centre personnel
or his, its or their agent or employee is, or areauthorized to
extend or enlarge this warranty on behalf of JVC.
2. Restrictions:
Cette garantie ne s'applique pas aux:
(a) Reparation ou remplacement de tout cabinet, batteries,
panneau avant, cordons de raccord, antennes, housses
de protection, boutons, couverts de hautparleur, cOnes de
hautparleur, ecrans de projection, protecteurs d'ecran de
projection et taus les accessoires.
(b) Taus defauts occasionnes au reparations requises su ite~ une
utilisationabusive, mauvaise, negligente et/ou uneutilization
incorrecte.
(c) Taus detauts occasionnes ou reparations requises suite
il l'omission de suivre les recommandations du manuel
d'instruction.
(d) Tout produit JVC alt~re , ajusteou repare par lout autre
entrepri se que JVC au un centrede service d'entretien ou de
service autorise JVC.
(e) Tout produit JVC dont le num~ro de serie aete altere, modiM
ou enleve.
(f) L'entretien, les verifications periodiques et nettoyage.
(g) Laconversion aune frequence au une tension etrangere au
domestique.
(h) Tout produit JVC n'ayant pas lesigne d'identification qui
conforme aux norms electriques Canadiennes (CSA).
(i) Pour tout produit utilise ades fins commerciales.
institutionnelles. de location au uti lise ~ des fins d'etalage.
Pieces ............... 1 An (Excepte les lilies video- 90 jours)
Main d'oeuvre ... 90 Jours
(j) Tout produit JVC ayant ete revendu et qui n'est plus Ia
propritl!Ei de l'acheteur original.
(k) Produit achete ~ "l'exterieur du Canada", provenant d'une
"faillite" ou d'un "liquidateur".
(I) Tout dommage cause par lefeu, une inondation, un eclair,
une surtension ou tout autre evenement hors du contrOiede
JVC.
5. Disclaimer of Consequential Damage:
To the extent the law permits JVC disclaims any responsibility
for loss of time or use of its product, transportation costs,
or any other indirect, incidental or consequential damage or
inconvenience.
WARRANTY TERM (VALID FROM THE DATE OF PURCHASE)
Product
Projection TV In-Home Service
Colour TV In-Home (25" and above)
D-ILA Rear Projection In-Home Service
LCD TV In-Home Service (25" and above)
Parts
(Years)
Labour
(Years)
1
1
* In-Home service to be provided where available.
Where it is not available, the purchaser must assume the
responsibility and expense for the proper packing, shipment
and all costs associated with the delivery of the equipment to
and from the closest JVC Authorized Service Centre.
Receivers and Home Speakers purchased
separately. Front Projection and Car
Audio "ARSENAL" Series
AC Adapters, Remote controls,
Headphones, Microphones and Projector
lamps
2
2
90 days 90 days
Wood Cone Speakers
5
5
All Other Categories
1
1
JVC CANADA INC.
6070 kestrel Road, Missisauga, Ontario, L5T 1 S8 Canada
TEL: (905) 670-3381 FAX: (905)670-7244 Service toll free #: 1-800-964-2650
http://www.jvc.ca E-mail: [email protected]
Product Registration
We suggest that you register your product since it will enable us to contact you directly if it is ever necessary to correct a safety related
condition in your product. You can register at http://www.jvc.ca/www/Support/Warranty.aspx
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of thecabinet. Retain this information for future
reference.
Model No.:
Serial No.:
Purchase date:
Name of dealer:
(m)POUR LES PRODUITS D'AUTOMOBILE
La garantie ne couvre pas l'~l im i nation d 'i nterf~rences
statiques auelectriques de Ia voiture, le nettoyage de tete,
les ajustements et les coOts de main d'reuvre associes a
l'enlevement au aIareinstallation de l'unitepour reparation.
3. Criteres:
Si un produit JVC s'averait defectueux, seton les conditions
applicables, les reparations necessaires seront effectues
sans coOts additionnels al'acheteur pour les pieces et Ia main
d'reuvre lorsque JVC reconnait que de tells d~fectuosites sont
causees par une defectuosite de materiel ou defabrication.
4. Exclusion de foutes autres garanties expresses :
Cettegarantie constitue l'entiere garantie express donnee par
JVCpour les produits JVC. Nul representant au employe d'un
detaillant au d'un service d'entretien n'est au toris~ aprolonger
cette garantieau nom deJVC.
5. Denegation des dommages in directs:
Dans Ia mesure permise par Ia loi, JVC nietoute responsabi l it~
pour perle de temps au d'usage de ses produits, des coots de
transport au tout autredommage au inconvenient indirect.
accidentel et cons~ quent
CONDITIONS DE GARANTIE (VALABLE~PARTIR DE LA DATE D'ACHAT)
Pieces Main-O'oeuver
Produit
I (Annees) (Annees)
~crans de projection Service a Domicile
Ecransde TVCouleurServiceaDomicile(25" et plus)
1
1
TVprojection arriere D-ILA Service aDomicile
Ecrans de LCD Service aDomicile(25" et plus)
*Service adomicile fourni par un detail Iant disponible.
S'il n'yapas de service JVC disponibleaproximite, l'acheteur doil assumer
Iaresponsabiliteet les coOtspour un emballage adequat, l'exprldition, ainsi
que tousles coots associesaIa livraisonde l'equipement chez et depuisle
detaillant JVC auto rise leplus pres pour un service d'entretien.
Recepteurs et Hauts-Parleurs achetes
s~par~ment , Projecteur Avant et Audio d'Auto
2
2
de S~rie "ARSENAL"
Adaptaleurs AC, T~l~commande . Casque
D'ecoute Microphones et Lampe deProjecteur 90 Jours 90 Jours
Enceinte acane en Bois
5
5
Toutes les autres cateoories
1
1
JVC CANADA INC.
6070 kestrel Road, Missisauga, Ontario, L5T 158 Canada
TEL: (905) 670-3381 FAX: (905)670-7244 Service toll free#: 1-800-964-2650
http://www.jvc.ca E-mail: service@jvc ca
Enregistrement du produit
Nous vous conseillons d'enregistrer votre produit, car il nous permettra de vous contacter directement si jamais elle est necessaire pour
corriger un problilme lie aIa securite de votreproduit. Vous pouvez vous inscrire ahttp://www.jvc.ca/www/Support/Warranty.aspx
Pour l'utilisation des clients:
Entrez ci-dessous le numero de modeleet le numero de serie qui se trouve soit ill'arriere, en bas ou sur lecOte de !'armoire. Conservez ces
informations pour ref~rence future.
No. de modele:
No. de serie:
Date d'achat:
Nom du revendeur: