LUMINETTE® Privacy Sheers - Diagram

Transcription

PRODUCT INFORMATION MANUAL
SECTION: 12 LUMINETTE® PRIVACY SHEERS
LUMINETTE® Privacy Sheers - Diagram
Standard Parts
ISSUE DATE: JANUARY 2012 REPLACES ISSUE DATE: DECEMBER 2008
ORIGINATOR: SKILTEC
APPROVED BY: D.ALTIPARMAKOVA
PAGE 1 OF 26
LUXAFLEX® LUMINETTE® Privacy Sheers offer a sophisticated vertical window covering solution. The soft
fabric vanes can be traversed to open and closed, or tilted to control light and privacy, and with PowerRise
Platinum Technology this is achieved with a touch of a button.
Drive Assembly
Modular Motor
Assembly
Platinum
Satellite Eye
DC Power
Supply
C-Clip
*See Section 7 Motorisation for Programming Instructions
ORIGINATOR: SKILTEC
PAGE 2 OF 26
Options & Limitations
LUMINETTE® Privacy Sheers Classic 89mm Vane Size
COMBINATION WAND/ CORD
SIDE STACK
TRAVELLING WAND
SPLIT STACK
SIDE STACK ONLY
MINIMUM WIDTH
300mm
300mm
MAXIMUM WIDTH
4875mm
3660mm
MINIMUM DROP
610mm
610mm
MAXIMUM DROP
3045mm
2540mm
MAXIMUM WIDTH
- End Mount
910mm
N/A
9750mm
7320mm
REVEAL FIT
Minimum Depth
Fully Recessed
25mm
160mm
N/A
N/A
29mm
100mm
50mm
16mm
29mm
100mm
50mm
16mm
32mm
32mm
MAXIMUM WIDTH
- Side by Side Drapes
FACE FIT
Minimum Mounting Surface
Overlap Each Side
Past Sill
Floor Clearance
END MOUNTING
Minimum Mounting Depth
STANDARD WANDS/CORDS
NON-STANDARD
WANDS/CORDS
FABRIC DROP
610-1040mm
1045-2135mm
2140-2615mm
2620-3045mm
760mm
1520mm 2030mm 2285mm
WAND/CORD
585mm
1015mm
1270mm
1780mm
2490mm
3045mm
3655mm
FABRIC DROP
610-1197mm
1198-2130mm
2131-2540mm
ORIGINATOR: SKILTEC
WAND/CORD
585mm
760mm
1015mm N/A
PAGE 3 OF 26
Options & Limitations
LUMINETTE® Privacy Sheers Quintette 120mm Vane Size
COMBINATION WAND/ CORD
TRAVELLING WAND
SIDE STACK
SPLIT STACK
SIDE STACK ONLY
MINIMUM WIDTH
460mm
765mm
460mm
MAXIMUM WIDTH
4875mm
4875mm
3660mm
MINIMUM DROP
610mm
610mm
610mm
MAXIMUM DROP
3045mm
3045mm
2540mm
910mm
910mm
N/A
9750mm
9750mm
7320mm
39mm
205mm
39mm
205mm
N/A
N/A
MAXIMUM WIDTH
- End Mount
MAXIMUM WIDTH
- Side by Side Drapes
REVEAL FIT
Minimum Depth
Fully Recessed
FACE FIT
Mounting Surface
Overlap Each Side
Past Sill
Floor Clearance
END MOUNTING
Minimum Mounting Depth
STANDARD WANDS/CORDS
NON-STANDARD
WANDS/CORDS
29mm
152mm
50mm
16mm
29mm
152mm
50mm
16mm
32mm
32mm
FABRIC DROP
610-1040mm
1045-2135mm
2140-2615mm
2620-3045mm
760mm
1520mm 2030mm 2285mm
WAND/CORD
585mm
1015mm
1270mm
1780mm
2490mm
3045mm
3655mm
FABRIC DROP
610-1197mm
1198-2130mm
2131-2540mm
WAND/CORD
585mm
760mm
1015mm
ORIGINATOR: SKILTEC
N/A
PAGE 4 OF 26
LUMINETTE® Privacy Sheers Measuring
- Classic 89mm Vane Size -
ORIGINATOR: SKILTEC
PAGE 5 OF 26
LUMINETTE® Privacy Sheers Measuring
- Quintette
120mm Vane Size ( only available in Portico fabric )
ORIGINATOR: SKILTEC
PAGE 6 OF 26
STACKBACK CHARTS
(FACE MOUNTS ONLY) - 89MM
ORIGINATOR: SKILTEC
PAGE 7 OF 26
STACKBACK CHARTS
(FACE MOUNTS
ONLY) - 120MM
( only available in Portico fabric )
ORIGINATOR: SKILTEC
PAGE 8 OF 26
LUMINETTE® Privacy Sheers
Installation & Care Instructions
Tools Required
• Flat blade and Phillips screwdrivers
•Level
•Needlenose pliers
•Measuring Tape
•Pencil
•Power drill and 6mm hex driver, and drill bits
•Razor utility knife
You will also need fasteners designed to work
with your specific mounting surface. Hex head
screws (32mm) are supplied.
MOUNTING
SURFACE
TYPE OF
FASTENER
Wood, Metal
No.6 Hex Head Screws (provided)
Drywall, Plaster
Wall anchors, Expansion Bolts
(Not Provided)
NOTE:
The hex head screws (included) must
contact wood studs for secure mounting. Otherwise, use all wall anchors or
fasteners such as expansion, toggle or
molley bolts (not included). For metal
surfaces, pre-drill the holes.
IMPORTANT:
Please read these instructions all the way through before installing.
ORIGINATOR: SKILTEC
PAGE 9 OF 26
STEP 1: UNPACK THE SHEER
Make sure you have clean hands or wear disposable gloves when handling LUMINETTE® Fabric.
To avoid wrinkling, do not fold the sheer or drape it over furniture.
•One or more LUMINETTE® Privacy Sheers may be packaged in a carton.
•The fabric panels are rolled around a cardboard tube. Do not remove the protective wrapping
until you are ready to attach the fabric panels (Step 4).
•Remove the SOFTRAK® Headrail System and mounting hardware from inside the carton.
•Remove the foam supports from the tilt shaft inside the headrail. Rotate the supports in either
direction until they can be pulled off.
•After unpacking the sheer, check that you have all the necessary parts for installation. Keep all
the packaging until the unit operates to your satisfaction.
NOTE:
With wider sheers, the SOFTRAK® Headrail System may be shipped separately.
INSTALL THE TRAVELLING WAND (Optional)
If your sheer was ordered with a Travelling Wand, it may be necessary to attach the wand to the
SOFTRAK® Headrail System. If so, refer to the illustrations and follow the numbered steps below.
1) Slide the cover off the top of the wand and remove the hook.
2) Attach the hook through the stem at the end of the scissors track.
3) Slide the cover up over the hook and stem.
4) Attach the wand to the bottom of the hook.
Squeeze the flat part of the wand against
the straight part of the hook.
5) Slide the cover down over the hook and
the top of the wand.
1
Cover
2
5
Hook
Wand
3
4
ORIGINATOR: SKILTEC
PAGE 10 OF 26
STEP 2: ATTACH MOUNTING BRACKETS
MOUNTING REQUIREMENTS
For proper operation, the SOFTRAK® Headrail System must be mounted level. Use a
level to check that the mounting surface is level and smooth on an inside mount (Reveal fit), and
that the bottoms of the installation brackets are level and aligned on an outside mount (Face fit).
If necessary, shim the brackets to ensure level mounting.
NUMBER OF BRACKETS NEEDED:
The number of mounting bracket units provided with each sheer depends upon the ordered width,
as shown in the table below.
ORDERED WIDTH
NUMBER OF BRACKET UNITS
Up to 1015mm
2
1016mm - 1780mm
3
1781mm - 2440mm
4
2441mm - 3940mm
6
3941mm - 4875mm
8
mounting bracket unit can be any combination of the following:
•A ceiling mount bracket unit
•89mm Vane Size one spacer block with one faceplate
•120mm Vane Size Three spacer blocks with one faceplate
•An extension bracket and cover with one ceiling mount bracket
89mm
Space Evenly
Space Evenly
89mm
Bracket
ORIGINATOR: SKILTEC
PAGE 11 OF 26
BRACKET SPACING:
Bracket spacing is the same for face fit, reveal fit, and ceiling fit installations.
Place two brackets on the mounting surface so their centres are 89mm in from the ends of the
SOFTRAK® Headrail System.
CAUTION:
Be sure to use a minimum of two mounting brackets per shade, to ensure proper
function.
•Space additional brackets, if supplied, evenly between the two end brackets. Use all the
mounting brackets recommended in the above table.
•Measure and mark all the bracket positions.
FACE INSTALLATION
BRACKET PLACEMENT:
The top of the sheer aligns with the top of the installation bracket, not the
removable tab. The tab serves as a spacer to prevent the brackets from being
mounted too close to the ceiling.
Removable
Tabs
For proper operation, the sheer must clear all obstructions, including window
cranks, and mouldings. Replace protruding window cranks with T-cranks.
Use additional spacer blocks or extension if more than 13mm clearance is needed
Spacer
Block
89mm Vane Size:
Requires a spacer block with a faceplate for 13mm clearance. Three additional spacer blocks
may be added for up to 50mm clearance.
120mm Vane Size:
Requires three spacer blocks with a faceplate for 13mm clearance. One additional spacer block
may be added for a total of 25mm clearance.
•Insert the screws through the opening on the front of the spacer block. Slide one bushing
over the end of each screw prior to securing the spacer block to the mounting surface.
•Attach the spacer block to a flat, vertical mounting surface at least 29mm high.
•Add any additional spacer blocks required.
•Hook the top of the faceplate to the front spacer block and snap into place.
•If more clearance is necessary than can be gained with spacer blocks, use extension brackets.
•Add Optional Components - Extension Brackets
ORIGINATOR: SKILTEC
PAGE 12 OF 26
NOTE:
Do not use more than a total of four spacer blocks. If additional
clearance is necessary, use extension brackets to gain additional
clearance.
Spacer
Block
Bushing
Faceplate
29mm
29mm Minimum Flat
Vertical Surface
Use three spacer blocks
for the 120mm vane size
USING SHIMS ON FACE FIT INSTALLATIONS
After installation, visually check along the length of the SOFTRAK®Headrail System for any bending
or bowing. If there is any bowing from side-to-side, add shims as needed to straighten the headrail.
•Remove the headrail.
•Remove the faceplate and any additional spacer blocks.
•Loosen the mounting screws securing the base spacer block.
•Insert one or more shims between the spacer block and the mounting surface.
•After reinstalling the headrail, check that you have corrected the bowing and the headrail is level.
REVEAL & CEILING FIT INSTALLATION
BRACKET ATTACHMENT:
• Attach the ceiling mount brackets directly to a level surface that has a minimum 25mm depth.
•To fully recess the sheer inside the opening, the flat surface must be 160mm deep with the 89mm
vane size and 205mm deep with the 120mm vane size.
•For proper operation, the sheer must clear all obstructions, including window cranks, handles, and
mouldings. Replace protruding window cranks with T-cranks.
•Use a level to check that the mounting surface is level and smooth. If
necessary, use shims to ensure level mounting of the SOFTRAK® Headrail
System.
25mm Minimum:
Inside Mount Depth
25mm
Minimum Fully Recessed Depth
89mm vane size: 160mm
120mm vane size: 205mm
ORIGINATOR: SKILTEC
PAGE 13 OF 26
USING SHIMS WITH INSIDE MOUNTS:
• Snap off the top of the shim for use with ceiling mount brackets.
•To achieve a straight and level headrail, add shims as needed between the mounting surface and
the ceiling mount brackets. Use a level as reference.
•To make further adjustments, you may add or subtract shims simply by loosening the mounting
bracket screws.
Snap off
Shim
Loosen
screws to add
or remove
Shims
CORNER AND BAY WINDOWS
•For bracket placement, mount the installation brackets 165mm from the corner for the 89mm
vane size or 191mm from the corner for the 120mm vane size.
•If additional spacer blocks or extension brackets are used, add the amount of extra clearance to
the 165mm for the 89mm vane size and 191mm for the 120mm vane size.
•For bay windows, treat the centre sheer as a corner sheer on both ends of the headrail.
Control End Cap
(Wand Side)
89mm
89mm vane size
120mm vane size
165mm
191mm
END MOUNTS FOR 89MM VANE SIZE
End mounting is used when conventional mounting techniques will not work, for example, on an
arch window.
ORIGINATOR: SKILTEC
PAGE 14 OF 26
191mm
120mm vane size
Control End Cap
(Wand Side)
89mm vane size
165mm
89mm
•Mount the extension brackets to the sides of the window opening at the desired height.
The mounting surface must be at least 32mm wide.
•Slide an extension base cover onto each extension bracket.
•Attach the ceiling mount brackets to the extension brackets using the machine screws (pointing
down) and speed nuts provided.
IMPORTANT:
End mounting is only available for 89mm vane size and a maximum sheer width of
910mm.
Machine
Screws
Extension
Bracket
Speed
Nuts
32mm
Minimum
STEP 3: INSTALL SOFTRAK® HEADRAIL
•Grooves on the back of the SOFTRAK® Headrail System are designed to
snap into the locking tab on the faceplate and ceiling mount bracket.
Tilt Up
•Tilt the front of the headrail (the side with the tilt reduction pinion
clips) up so the top groove fits into the locking tab on each installation
bracket.
•With the top groove in place on all brackets, tilt the headrail down
so the bottom groove fits into the locking tabs on the installation
brackets.
•After positioning/adjusting the SOFTRAK® Headrail System, lock the
headrail into place by tightening the locking screws on the bottom of
the brackets until they are just snug.
ORIGINATOR: SKILTEC
Locking
Tab
SOFTRAK®
Headrail
System
Tilt Down
SOFTRAK®
Headrail
System
Locking
Screw
PAGE 15 OF 26
POSITIONING THE SOFTRAK® HEADRAIL SYSTEM:
After the SOFTRAK® Headrail System is installed into the installation
brackets, check the clearance at each end.
NOTE:
The recommended amount of clearance varies according to control end and stack
design, as shown below.
REVEAL FIT AND WALL-TO-WALL FACE FIT
Right Stack Design - Minimum Clearance
19mm
Non-Control End
6mm
Control End
Left Stack Design - Minimum Clearance
6mm
Control End
19mm
Non-Control End
Split Stack Design - Minimum Clearance
6mm
Control End
6mm
Non-Control End
NOTE:
After positioning/adjusting the SOFTRAK® Headrail System, lock the headrail into
place by tightening the locking screws on the bottom of the brackets until they are
just snug.
SIDE-BY-SIDE (ABUTTED) INSTALLATIONS
There are three options for side-by-side installations: a control end cap next to a control end cap,
a control end cap next to a non-control end cap or a non-control end cap next to a non-control end
cap. The three illustrations below show proper headrail placement for all three options.
•Correct spacing between end caps allows for proper swivel arm operation.
•Be sure to measure the spacing from end cap to end cap, not from the swivel arms.
•A simulated split stack (the fabric opens in the centre) is the same as a non-control/non-control
side-by-side installation.
CONTROL/NON-CONTROL
CONTROL/CONTROL
Control
End Cap
13mm
Control
End Cap
Control
End Cap
25mm
Non-Control
End Cap
Swivel Arm
ORIGINATOR: SKILTEC
PAGE 16 OF 26
SIDE-BY-SIDE (ABUTTED) INSTALLATIONS (CONTINUED)
NON-CONTROL/NON-CONTROL
Non-Control
End Cap
38mm
Swivel Arm
Non-Control
End Cap
Swivel Arm
NOTE:
After positioning/adjusting the SOFTRAK® Headrail System, lock the headrail into
place by tightening the locking screws on the bottom of the brackets until they are
just snug.
STEP 4: ATTACH THE FABRIC PANEL(S)
PREPARATIONS:
Tube
• Use the wand to rotate the tilt reduction pinion clips perpendicular to the headrail.
Fabric
Header
•Pull the cord or Travelling Wand to move the fabric carriers to the fully stacked
position.
Fabric
Panel
•Remove the protective wrapping from the fabric, but do not unroll it from the
cardboard tube.
•Stand the tube on end on a clean surface with the header at the top. Position the
tube at the end of the SOFTRAK® Headrail System where the fabric stacks.
•If the tube is too long to stand on end, trim it with a sharp razor knife. Do not cut
the fabric. Do not unroll the fabric until you begin attaching the vanes to the pinion
clips.
ATTACH THE VANES TO THE PINION CLIPS:
•Unroll the fabric to gain enough slack to attach the polytab of the first
vane to the first pinion
clip.
•To attach the vane, insert the polytab into the pinion until it snaps
securely into place.
•Unroll the fabric as you clip the rest of the vanes into the pinion clips in
sequence. Be careful not to skip any pinion clips or vanes.
ORIGINATOR: SKILTEC
Pinion
Clip
Polytab
Installed
Vane
Vane
PAGE 17 OF 26
ATTACHTHE SWIVEL PLATES:
• Attach the swivel plates to the control end cap or the swivel arm as shown. Swivel plates are
right and left specific (an L or R can be seen on the swivel plate).
•The rivets (attach to the swivel plates) snap onto the control end cap and/or swivel arm
between the upper and lower clips of the swivel plates.
LEFT STACK SHOWN (FABRIC NOT SHOWN)
Clips
Rivet
Control End Cap
Rivet
Swivel Arm
Rivet
Control End Cap
Rivet
Clips
Swivel Arm
ADJUST THE END TREATMENT TO THE SWIVEL PLATE, IF NECESSARY:
• If the end treatment is not hanging straight or if the vanes are not
uniform, simply separate the VELCRO® brand fasteners attachment
and reposition the end treatment on the swivel plate.
Separate the VELCRO® brand fasteners by pulling upward on the end
treatment and downward on the swivel plate.
Velcro
•Hold the end treatment near the swivel plate at a height where
the end vanes hang straight and the top of the end treatment is
approximately 3mm above the top of the swivel plate.
•Attach the end treatment to the swivel plate by pressing together
the two strips of VELCRO® brand fasteners. Repeat the adjustment
Control
End Cap
Rivet
End Treatment
ORIGINATOR: SKILTEC
PAGE 18 OF 26
TRAVERSE THE SHEER & ROTATE THE VANES
TRAVERSE THE SHEER:
NOTE:
The vanes must always be open when traversing the sheer.
•Use the operating cord or Travelling Wand to traverse the sheer. Refer to the illustrations
below.
•The sheer should move easily and not stick or jam at any point along the SOFTRAK® Headrail
System.
ROTATE THE VANES:
• Use the wand to rotate the vanes. With the fabric fully traversed across the headrail, turn the
wand to rotate the vanes to the left and right to observe their closure. They should be
synchronised, opening and closing easily.
Wand/Cord Operation
Travelling Wand Operation
Traverse
Fabric
Rotate
Vanes
Rotate
Vanes
Push Wand To
Stack Vanes
Pull Wand To
Draw Sheer
Closed
REMOVING THE SHEER
NOTE:
Make sure you have clean hands or wear disposable gloves when handling
LUMINETTE® Fabric. Select an area in the home where the sheer can be laid flat. To
avoid wrinkling, do not fold the sheer or drape it over furniture.
ORIGINATOR: SKILTEC
PAGE 19 OF 26
REMOVE THE FABRIC FROM THE HEADRAIL:
• Traverse the sheer to the fully stacked position.
•Detach both end treatments from the ends of the headrail, as shown.
Separate the velcro by pulling upward on the
end treatment and downward on the swivel
plate.
Removing the
fabric vanes
Control
End Cap
Velcro
Pinion
Clip
Rivet
End Treatment
Vane
•Remove the fabric from each pinion clip. Hold the top of the vane near the polytab, and pull
down and to the left.
•Lay the fabric flat on a clean surface with the vanes facing in the same direction.
•If the original tube is available, gently roll the fabric onto it, making sure the fabric stays
straight. Do not roll the fabric too tightly.
REMOVE THE HEADRAIL:
• With the fabric removed, loosen and push up on the locking screw until the locking tab releases
from the headrail.
•Rotate the eadrail up as shown, until the bottom releases from the bracket.
•Once the bottom releases, pull the headrail out from the brackets and remove.
Tilt Up
Locking Tab
Locking
Screw
Loosen and Push Up
ORIGINATOR: SKILTEC
PAGE 20 OF 26
CARE AND CLEANING
LUMINETTE® Privacy Sheers are as durable as they are beautiful. With
proper installation and care, they will provide many years of beauty and
performance.
The sheer, valance, and vane fabric are 100% polyester. They are
resilient, anti-static, and dust resistant. Periodic cleaning is
recommended to help keep LUMINETTE® Privacy Sheers looking like
new. For all cleaning applications, sheers should remain hanging to
minimise handling, wrinkling or puckering.
NOTE:
Disposable gloves should be worn when handling sheers.
CAUTION:
Keep all cleaning solutions away from the SOFTRAK® Headrail
System. Never submerge the headrail.
ROUTINE CLEANING:
• Use a feather duster for regular light dusting.
• For more thorough dust removal, a hand held vacuum with low suction may be used. When
vacuuming avoid pulling or stretching the fabric.
• Start in the upper left corner and work across the sheer using short horizontal strokes while
steadying the fabric free with your hand. Each stroke should be approximately the width of
two to three vanes. Do not use long horizontal or vertical strokes, as these actions will
crease the fabric. Continue to the bottom of the sheer.
• Do not use a brush attachment or rigorous vacuuming since either could distort the sheer
fabric.
ELECTROSTATIC CLEANING:
CAUTION:
Do not use electrostatic cleaning services such as
Swiffer™ or Pledge Grab-it™ on any LUMINETTE® Privacy Sheers.
SPOT CLEANING:
To reduce the potential for permanent staining, spots should be treated and cleaned as soon as
possible with a clothing stain pre-treatment solution.
•Apply a pre-treatment solution to a clean white cloth.
ORIGINATOR: SKILTEC
PAGE 21 OF 26
SPOT CLEANING (CONTINUED):
•Support the fabric from behind using another clean dry cloth. Clean the spot using a gentle
blotting action. Avoid rubbing the fabric since any abrasive action may cause it to distort.
•Let the area air dry.
•After the area is dry, remove excess solution by blotting it with distilled or bottled water applied
to another clean cloth.
DEEP CLEANING:
For deep cleaning LUMINETTE® Privacy Sheers, the ultrasonic cleaning method is recommended.
CAUTION:
Always use an experienced professional for cleaning LUMINETTE® Privacy Sheers, to
avoid damaging the product.
DO NOT DRY CLEAN LUMINETTE® Privacy Sheers.
ULTRASONIC METHOD:
Professional ultrasonic cleaning is a process in which the sheer fabric is inserted into a tank of
cleaning solution and then subjected to high frequency vibrations. Dirt is loosened from the fabric
and carried away in the cleaning solution. This process is done outside the home.
•Ensure the supplier’s ultrasonic tank is long enough to accommodate the full length of the
sheer without folding the fabric or vanes.
•Ensure the sheers are rolled onto a tube when being transported to and from the home. This
reduces the chance of wrinkling and damage.
•Specify water that does not exceed 32°C.
CAUTION:
If water temperatures exceed 32°C, oxidation will damage the room darkening vanes
of LUMINETTE® Room Darkening Sheers.
•Make sure stains are pre-treated to maximise the benefits of cleaning.
•Hang sheers immediately after cleaning with the vanes open and the loops evenly spaced.
Allow the sheer to drip dry completely.
ORIGINATOR: SKILTEC
PAGE 22 OF 26
WRINKLE AND CREASE REMOVAL:
Both the hand and steam machine methods described below are suitable for wrinkle and crease
removal. The hand method is more appropriate for smaller areas.
HAND METHOD:
• Rotate vanes to the fully opened position.
• Apply warm distilled or bottled water to a clean white cloth.
• Support the fabric from behind using another clean, dry cloth.
• Blot the wrinkled or creased area with the wet cloth.
• Let the area air dry.
STEAM MACHINE METHOD:
• Rotate vanes to the fully opened position.
• From behind direct the steam (maximum temperature 38°C) from a portable steam machine to
penetrate the sheer fabric.
• Use slow, short vertical movements. Begin at the top of the sheer and work your way down.
Several passes over the creased area may be needed.
• Let the area air dry.
A NOTE ABOUT TEXTILES:
Like any work of textile art, whether an antique or hand-spun sheer, the fabric is subject to slight
variations.
•The fabric will change as its position changes.
•Minor wrinkles, puckers or other variations can appear and are inherent to this textile product.
Slight puckers in the sheer fabric may be most noticeable when the sheer is traversed across the
opening after having been in the stacked position for a period of time. If desired, the sheer may
be steamed to minimise these minor variations. Steam from the rear side of the fabric whenever
possible.
•Such variations like those just mentioned, are normal acceptable quality.
WARRANTY
LUMINETTE® Privacy Sheers are covered by the LUXAFLEX® 5 Year Warranty.*
Conditions apply.
*
During winter in particular, condensation may develop on the glass of the window due to the
insulation abilities of the product. If condensation does occur it is essential that the blind be
retracted for a period to allow for maximum air flow and the evaporation of the moisture to
minimise damage to the blind fabric.
ORIGINATOR: SKILTEC
PAGE 23 OF 26
TROUBLE SHOOTING
PROBLEM
SOLUTION
The sheer does not traverse, or does not traverse easily
•
Tilt the vanes to the opened position before traversing.
•
Check that the installation brackets are level, their front edges are
aligned, and there are no obstructions to the movement of the
fabric (i.e, the cord is not caught in the brackets).
The sheer end treatment does not hang straight
•
Separate the velcro strips. Reposition the end treatment on the
swivel plate. Repeat as necessary until the end treatment hangs
straight. See Adjust The End Treatment To The Swivel Plate section.
The vanes do not rotate or they rotate incorrectly
•
Check the sheer is fully traversed.
•
Check that there are no obstructions to the movement of the
vanes. Replace protruding window cranks with T-cranks.
A vane does not hang correctly
•
Check that the vane is completely inserted into the pinion.
See Attach The vanes To The Pinion Clips - section.
A vane is out of alignment
•
Using the wand, first rotate the vanes all the way to one side and
then all the way to the other. The vane (s) will automatically
realign.
•
Manually turn the pinion clip to align with the remaining pinion
clips.
•
On inside mounts, check that there is a clearance between the
end of the headrail and the window casement.
The end treatment arm does not swing around the end cap
See Positioning The SOFTRAK® Headrail System - section.
The two fabric panels on a split stack sheer don’t quite
meet in the centre
•
While up to a 6mm gap is within product
tolerances, you can usually ensure that the
two lead vanes meet in the centre by cupping
them with clean hands and rounding them
along the length of the fabric.
•
Raise or lower the cord tether to adjust cord
tension.
Cord tension is incorrect.
Wand does not hang straight or cord is too loose.
•
Using a .05 hex key, loosen the set screw in
the wand lock; raise the tether to decrease
tension; lower the tether to increase tension.
Tighten the set screw and check the adjustment.
ORIGINATOR: SKILTEC
PAGE 24 OF 26
LUXAFLEX® LUMINETTE® Privacy Sheers
‘Return to Wall’ Product Improvement
LUXAFLEX® LUMINETTE® Privacy Sheers offer a softly filtered view whilst providing
privacy, which is easily controlled with the tilting of the sheer fabric vanes. LUMINETTE
Privacy Sheers create instant drama in any room and are the ultimate choice for vertical
window covering solutions.
‘Return to wall’ example
This July we announced that fabric ‘return to wall’ feature
would be a standard on all face mounted 89mm Classic
LUMINETTE Privacy Sheers fabrics. This product
improvement creates a seamless and finished appearance,
further refining the look of LUMINETTE Privacy Sheers
(return to wall example pictured on left).
The ‘return to wall’ feature
means that fabric end
treatments on both the control
end and the non control end
fully return to the wall. Face
mount ‘return to wall’ pictured
to the right.
‘Return to wall’
There has been some confusion regarding the componentary, particularly end treatment
swivel plate assembly, which should be received with LUMINETTE Privacy Sheers which
include the ‘return to wall’ feature.
Return to Wall Feature
UMINETTE Privacy Sheers with ‘return to the wall’ will have a full vane on the control
side and NO end treatment swivel plate assembly on the control end, the 1st vane
on the control end is attached to the ‘return to wall’ clip. Only the non control end
features an end treatment swivel plate assembly. See below.
Control End only
features full vane and
a ‘return to wall’ clip.
No end treatment
swivel plate assembly.
Non-Control End
Non Control End features
full vane and end treatment
swivel plate assembly.
Control End

ORIGINATOR: SKILTEC
PAGE 25 OF 26
Non Return to Wall Feature
LUMINETTE Privacy Sheers which are 89mm Classic fabric and reveal mounted, along
with all 120mm Quintette fabrics feature ‘no return to the wall’. This means that these
shades will have a 1/2 vane on the control side and end treatment swivel plate assembly
on both the control end and non control end. See below.
Control End only
features half vane
and a end treatment
swivel plate
assembly.

Non Control End
features end
treatment swivel
plate assembly.

LUMINETTE Privacy Sheers Split Stack with ‘Returns to Wall’
Please note for a split stack (one shade is a left stack and the
other is a right stack, with the fabric opening in the centre) the
two side stack systems are installed with the non-control ends
side-by-side. Be sure to adjust the SoftTrak headrails
according to the illustration for proper swivel arm operation. Be
sure to measure the spacing from end cap to end cap, not
from the swivel arms.


LUMINETTE Privacy Sheers window coverings with ‘returns to the wall’ end treatments
are not recommended on the split stacks with abutting ends. Should your sheers arrive
with ‘return to the wall’ end treatments on the abutting ends, simply switch the two end
treatment swivel plates so that the end treatments look like the below illustration.

ISSUE DATE:
ORIGINATOR: SKILTEC
 JANUARY 2012 © Copyright
2011
Hunter
Douglas
Limited [ABN
98 009 675
709]
REPLACES
ISSUE
DATE:
DECEMBER
2008
APPROVED
BY: D.ALTIPARMAKOVA
® Registered Trade Marks of Hunter Douglas Limited 12/2011
PAGE 26 OF 26

LUMINETTE® Privacy Sheers - Diagram

Transcription

Similar documents

DECORATIVE FABRIC SALE Boca Bargoons has 1000`s and 1000`s

Magnum-Metal Sp. z o.o. ul. Ceramiczna 2 98

Newsletter 7 1984 - Tools and Trades History Society

mariners supply pigeon forge

LUMINETTE Privacy Sheers - New Zealand Window Shades

C4152 Luminette Brochure - Hunter Douglas Commercial

Form 990 for GLADWYNE MONTESSORI SCHOOL (23

Vertical Blind System

lUXAFleX® Luminette® privAcy sheers

LU004 Hockney Corner Sofa - sofa comes in two parts to form an L