pdf Brochure

Public Auction Tuesday, June 28, 2011
James G. Murphy Inc.
Commercial & Industrial Auctioneers
P.O. Box 82160, Kenmore, WA 98028
NO MINIMUMS - NO RESERVES
James G. Murphy Inc.
Commercial & Industrial Auctioneers
PUBLIC AUCTION
Snow Mountain Mill
James G. Murphy Inc.
Commercial & Industrial Auctioneers
Sawmill Equipment, Rolling Stock
www.murphyauction.com
425.486.1246 or 800.426.3008
TERMS & CONDITIONS
An On-Site Buyer’s Premium of 10% will be charged on all successful bids.
An Online Buyer’s Premium of 13% will be charged on all successful bids.
PAYMENT: Full payment must be made by no later than 4pm, Wednesday, June 29.
A 25% deposit is required by the close of business, auction day.
Cash, cashiers check, Master & Visa Cards, wire transfers only. Personal or
company checks accepted ONLY with bank letter of guarantee.
Absentee bids accepted with 25% deposit
REMOVAL: No purchase may be removed during the auction unless otherwise
announced by the auctioneer. Removal schedule announced on auction day.
Announcements made by the auctioneer at the time of sale take precedence over
printed matter.
Auctioneer reserves the right to sell accessories, parts or attachments on a separate
and/or aggregate basis.
Due to safety & insurance reasons, persons under 12 not admitted.
Washington Auctioneers License #1960
LODGING
Anacortes
Anacortes Ship Harbor Inn
Anaco Bay Inn
Cap Sante Inn
Majestic Inn & Spa
The Marina Inn
Burlington
Hampton Inn & Suites
Holiday Inn Express & Suites
800-852-8568
360-299-3320
360-293-0602
360-299-1400
360-293-1100
360-757-7100
360-755-7338
AIRPORTS
Bellingham International Airport – Serving Alaska Airlines, Horizon Air & Allegiant Air
Seattle-Tacoma International Airport – Serving all major airlines
DRIVER DIRECTIONS
From north or southbound I-5, take the Anacortes/Hwy 20 exit (#230) to westbound
Hwy 20. Drive west on Hwy 20 approximately 9 miles to S March Point Rd. Drive
northwest on March Point Road approximately 6/10 mile to the auction site,
located on the right
WATCH FOR AUCTION SIGNS
Food Service Available at the Auction Site
9663 S March Point Rd
Anacortes, WA 98221
2007 Cat 216B
James G. Murphy Inc.
Commercial & Industrial Auctioneers
PUBLIC AUCTION
Snow Mountain Mill
9663 S March Point Rd
Anacortes, WA
Bid live or bid online with MurphyLIVE!
Tuesday, June 28, 2011• 10am
2003 Cat 962G
1986 Salem TwinBandmill
Bid live or bid online with MurphyLIVE!
Tuesday
June 28, 2011
Auction Starts at 10am
Preview 8am - 4pm, Monday, June 27
For more information go to www.murphyauction.com • Phone 425.486.1246
Debarkers
Hog – Chipper – Chip Pac – Chip Screen
Buildings
SALEM BRUNETTE MKII 21” 5-arm ring debarker, air seal, auto centering ring, 60 hp ring drive, 40 hp LINCOLN feed drive, alligator chain feed thru, air
operated in & outfeed hold downs, 4’x4’ operators cab, 15 hp hydraulic unit, air receiver, KOYO DIRECT LOGIC 06 PLC, s/n: 122210, spare debarker sold
separately
MORBARK 640 rosserhead debarker, 6”-36” diameter capacity, up to 80 fpm, 20” top cutter head & feed wheel w/LINCOLN 100 hp main drive, 40 hp auxiliary
drive, 110 gallon hydraulic tank, operators cab, 25’-13” track type infeed conveyor, 25’ WD110 box chain outfeed conveyor w/4-arm log kicker, hydraulic
driven, air receiver, 53’-6” overall length, 11’-6” wide, 8’-10” high, weight approx 21,000 lbs, s/n: 1048
GRUENDLER 36-4 wood hog/hammer mill, 100 hp/1200 rpm arbor drive, 35-1/4” top feed, 38-1/4” bottom discharge, (4) rows w/(18) approx 56 lb hammers,
SQUARE D ALTISTART 48 200 hp soft start, KOYO DIRECT LOGIC 06 PLC, spare hammer, s/n: 5367
PRECISION 48” 6-knife chipper, LINCOLN 150 hp arbor drive, horizontal infeed, top discharge, SAFTRONICS EZ6 240 stack solid state starter
MORBARK CHIP PAC 58, 58” chipper, 6’x6’ screen combination, TOSHIBA 125 hp/1765 rpm, 15600 lbs, s/n: 505
PRECISION CS66 chip screen, 6’x6’ 2-deck w/3-1/2’ diameter cyclone, s/n: 878
2006 VARCO PRUDEN 25’ eaves-28’ peak height x 60’-75’ wide x 135’ long all steel engineered sawmill building, 25 psf snow load, 85 mph wind load, zone 3
seismic, roof insulation w/mesh, lighting & electrics, commercial fire protection dry type fire system
25’ eaves-31’ height x 35’ wide x 75’ long wood framed steel clad sawmill building w/32’ wide x 36’ long addition
14’ eaves-17’ peak height x 32’ wide x 48’ long wood framed, steel clad green chain building
15’x56’ mobile home/office w/(2) bedrooms, (1) bath, wood porch w/wheel chair ramp
(2) 40’ & (3) 20’ cargo containers
Group of (1) 40’ & (2) 20’ cargo containers (welded together)
Cut Off Saws
SODERHAMN 48” insert tooth whole log cut off saw, TOSHIBA 50 hp, approx 50 hp hydraulic unit, (2) log clamps, TECO/WESTINGHOUSE MA7200 AC
inverter, KOYO 06 PLC, 8’x10’ operators cab, s/n: 0187
Custom built 72” insert tooth whole log cut off saw, approx 100 hp, (2) hold down bars, 38’ box chain infeed log haul, 25’ box chain outfeed log haul w/5-arm
kicker, gearhead motors, newer electrics
Sharp Chain Twin – Resaws
1986 SALEM right hand temposonic positioned twin sharp chain bandmill, TOSHIBA 150 hp/1180 rpm arbor drives, air strain, hydraulic sharp chain w/
centering rolls, marked controls in cab, CM&E 85 temposonic positioned segmented slabbers, TOSHIBA 150 hp/1180 rpm, key knife system, 1999 INOVEC
SETMASTER scanning w/6” min. diameter x 28” max. x 8’ min. length x 28’ max. length parameter lasers, racks, INOVEC 60 & 40 hp hydraulic units, (4)
SQUARE D ALTIVAR 200 hp soft starts, (2) KOYO 06 PLC’s ($80,000 new sharp chain at install), 6’x6’ air conditioned, soundproof control booth
STENNER 42” single band horizontal resaw, approx 40 hp, air strain, hold down roll, 20’ infeed rollcase w/(6) 8-1/2”x34-1/2” knurled & smooth rolls, 3’ 4-strand
jump transfer, board hooks, 6’ outfeed rollcase w/(5) 8-1/2”x20-1/2” knurled & smooth rolls, drives, TECO WA7200-405-N1, 5 hp digital AC drive, cab,
controls
PRESCOTT 5’ single band horizontal resaw, GE 75 hp, hold downs, in & outfeed w/controls, spare frame, wheels
BAKER BBR-0 single band horizontal bandmill, 30 hp, hydraulic 8” feed thru belt, in & outfeed rolls, s/n: 94-857
Head Rig – Hydraulic Log Turner
SALEM 6’ canted RH vertical band head rig, approx 150 hp AC drive, mechanical strain, outfeed rolls, SAFTRONICS EZ6-180 HD 200 hp solid state starter,
s/n: 121058
Hydraulic log turner w/THERMAL TRANSFER 20 hp hydraulic unit, control & valve in cab
Carriage – Drive – 3D Carriage Scanning
CAE 14’x50” 3-knee, canted temposonic positioned carriage, (2) log flippers, (3) hammer dogs, center cant hook, (6) trucks, pantograph arm, ACE bumpers,
180’ of track w/INOVEC TAPERMASTER setworks, THERMAL TRANSFER 50 hp hydraulic, cab & controls
ASSOCIATED ELECTRIC 125 hp/485 rpm/230 volt/353 amp carriage drive motor to HAMILTON size H2280 reducer w/8.326:1 ratio reducer, GE 125 hp/250
volt DC motor to RELIANCE 150 hp/1755 rpm AC motor gen set, SAFTRONICS EZ6-125, 150 hp solid state starter
2006 INOVEC YIELD MASTER G3 stereo scan 3D contour scanning carriage optimizer, s/n: 100602 w/16’ scan bar, (3) DYNAVISION L4A-90-30-31 (60)
scan heads, s/n: L221286, L2201290 & L2201236, 10’x12’ air conditioned sound proof operators cab (not installed)
Edgers
SCHURMAN 4TA24, 4”x24” splined top arbor board edger w/2-saw setworks, TOSHIBA 150 hp/1175 rpm arbor drive, 7.5 & 10 hp feed drives, 2005 SQUARE
D ALTISTART 48Y range 200 hp soft start, lasers, lube system, 15’ infeed rollcase, 4”x20’ outfeed belt transfer w/SKK gearhead, spare saws, new guides,
s/n: 1327
PORTLAND IRON WORKS 89, 8” combination edger w/4-saw setworks, (2) TOSHIBA 250 hp arbor drives, (2) motor to FALK square box reducers,
feed drives, 40” & 30” knurled feed thru rolls, #3 splined arbor, (2) 2005 SQUARE D ALTISTART 48Y range 250 hp soft starts, KOYO 06 PLC’s, (2)
SAFTRONICS GP10 open loop vector drives, PFS 20 hp hydraulic unit, lasers, 6’x6’ operators cab, 21’ split infeed rollcase w/jump transfer, (3) drives, 25’
outfeed rollcase, motor to FALK reducer, spare saws, new guides, s/n: 23031
PORTLAND IRON WORKS 89, 8”x48” top arbor board edger w/4-saw setworks, LINCOLN 100 hp arbor drive, TECO 10 hp feed drive, 25 hp hydraulic unit,
lasers, 11’ powered infeed rollcase w/10’ linebar, 5’ 6-strand H78B lumber landing table outfeed, spare saws, s/n: 4099
SCHURMAN 8SBA20, 8”x30” splined bottom arbor edger, knurled bed rolls (no drive motor, not installed), s/n: 2071
Trimmers
Custom built cut 20’ pass 28’ line shaft driven trimmer, approx 60 hp drive, (11) 22” air drop saws, 8’ 10-strand 81X lug feed thru transfer w/gearhead motor,
KOYO DIRECT LOGIC 205 PLC, spare saws
ALBANY 16’ cut 20’ pass line shaft trimmer, 40 hp drive, (9) saws (not installed)
Chip Bin – Trailer Loader
PEERLESS approx 30-unit hydraulic chip bin w/hydraulic unit
7000 lb capacity trailer loader w/approx 8000 lb winch, cable, pendant controls, attached electrics, (4) vertical post style
Vibratory Conveyors – Metal Detectors
ACTION 20”x64’ balanced vibratory conveyor, TOSHIBA 10 hp, 3/4”, 425 rpm w/5’ tub, s/n: C-1291-4, MDI CCW64 metal detector, s/n: 11774
ACTION SSD24120-F/3, 24”x30’ vibratory conveyor, 5’ tub w/MDI metal detector
Compressors – Dryer – Air Receivers
QNW 490B rotary screw compressor, US 125 hp, air cooled SQUARE D ALTIVAR 48 soft start, 17213 hrs, s/n: 800433
(2) COMPAIR KELLOGG CYCLON 6075 CN rotary screw compressors, 75 hp, air cooled, 20707 hrs, s/n’s: V9E42848 & 9977 hrs, s/n: N/A
KAESER KLD 950 twin tower pressure swing regenerative desiccant compressed air dryer, 590 scfm @ 100 psig, s/n: 3338-2-9805-3KD
WILKERSON refrigerated air dryer (not installed)
RICHMOND ENGINEERING 4’x10’, 125 psi air receiver, s/n: K41111-TK-10
HANSON 3-1/2’x9’, 125 psi air receiver
Electrical
2005 EATON/CUTLER HAMMER 2500 amp 3-section POW-R-LINE-C switchboard, 480Y/277 volts, s/n: 85ES4969
PRINGLE 2500 amp main w/(3) 600, (3) 400 & (3) 200 amp breakers
FPE 2500 amp main w/(3) 600, (3) 400 & (3) 200 amp breakers
(9) SQUARE D ALTISTART 48 & 48Y soft starts to 250 hp
TECO/WESTINGHOUSE MA 7200, 50 hp AC inverter
TECO MA 7200-405-N1, 5 hp AC inverter
SAFTRONICS EZ6 180 HD, 200 hp solid state starter
SAFTRONICS EZ6 125, 150 hp solid state starter
SAFTRONICS SY6 125, 75 hp solid state starter
(2) SAFTRONICS GP10 open loop vector drives
WESTINGHOUSE 2100 3-section MCC w/(32) switches
CH EATON 5-section MCC w/(18) switches
WESTINGHOUSE 2-section, 2-sided MCC w/(15) switches
Transformers to 75 kva, lighting electrics, breakers, disconnects, wire & conduit lot
Filing & Grinding Room Equipment
ARMSTRONG #4 RH automatic bandsaw sharpener, s/n: 6105
ARMSTRONG #4 LH automatic bandsaw sharpener
ARMSTRONG #2 RH automatic bandsaw sharpener, s/n: 12255
ARMSTRONG #2 LH automatic bandsaw sharpener, s/n: 8218
ARMSTRONG #4 bandsaw stretcher roll w/anvils & stands, s/n: 7951
ARMSTRONG #54 hand sharpener
OREGON 511A chain sharpener
THOMAS LANE saw guide milling machine
IMW guide resurfacer
MORBARK 45 travel bed knife grinder, s/n: 366
PRECISION tub grinder w/20” knife holders
Large square babbit pot w/babbit
AGET DUSTKOP dust collector
(20±) New edger guides, guide press & jigs
Spare bandsaws, round saws, knives
Bid live or bid online with MurphyLIVE!
Log Decks
40’ 8-strand H-chain log deck w/6-arm LS&L, 5-arm kicker, S-drive, gearhead motor (located at 20” debarker)
28’ 4-strand H-150 log deck w/4-arm LS&L, pin stops, TOSHIBA 15 hp, to SKK 16.5 rpm reducer (located at sharp chain)
24’ 5-strand H-chain log deck w/5-arm LS&L, S-drive, gearhead motor (located at MORBARK)
22’ 6-strand H-chain log deck w/9-arm LS&L, S-drive, gearhead motor (located at 48” cut off saw)
22’ 7-strand H84 w/flites log deck w/6-arm LS&L, 3-arm log stop, H-shaft, gearhead motor (located at head rig)
16’ 5-strand H-chain log deck w/5-arm LS&L, S-drive, gearhead motor (located at 72” cut off saw)
Log Hauls
44’ 6”x11-1/2” box chain infeed log haul, S-drive, gearhead motor (located at 20” debarker)
42’ straight bar chain outfeed log haul, S-drive, gearhead motor (located at 20” debarker)
38’ 6”x11-1/2” box chain infeed log haul, S-drive, gearhead motor (located at 72” cut off saw)
36’ 6”x11-1/2” box chain infeed log haul, S-drive, motor to FALK reducer (located at 48” cut off saw)
30’ 2-strand H150 outfeed log haul w/lumber stops at 8’-22’, scan eyes, motor to reducer (located at 48” cut off saw)
25’ box chain outfeed log haul w/5-arm kicker, gearhead motor (located at 72” cut off saw)
Rollcases - Transfers - Conveyors
18”x30’ hourglass outfeed rollcase w/4-arm log kicker, motor to reducer (located at 48” cut off saw)
(20±) Transfers to 61’
(20±) Conveyors to 40’
Rollcases to 30’
Shop Equipment, Tools, Mill Equipment
Large assortment of shop equipment & tools including: MILLER SRH330, SRH 303, Goldstar 300 SS 300 amp welders; (2) SURE WELD DRH333 300 amp
welders, (3) oxy/acet sets, (3) STIHL chain saws, ARCAN hydraulic press; JET horizontal band saw; DEWALT chop saw, JET 8” pedestal grinder, BOSCH
roto hammer, MILWAUKEE porta-band saw, 2 ton hydraulic engine hoist, TRADES PRO portable air compressor, steel banding cart, motors to 250 hp,
sharp chain infeed table w/rolls, jump chain, INOVEC positioners, FAC 50 hp twin pump hydraulic unit, 60 gpm, 1500 psi, 300 gallon reservoir, FAC/
INOVEC 50 hp hydraulic unit, 4’ diameter x 12’ long diesel tank w/15 hp FILL-RITE pump, steel containment, and MUCH MORE
Rolling Stock
2007 CAT 216B skid steer loader, 5’ bucket, CAT 3024C 4 cyl diesel, 652 hrs, s/n: CAT0216BHRLL06225
2003 CAT 962G SERIES II wheel loader w/CAT 5’ log forks, 4f/4r, auto lube, 14,500 hrs, s/n: CAT0962GTAXY00256
1984 CAT 966D wheel loader w/MEDFORD 5’ log forks, 4f/4r, 8400 hrs, s/n: 99Y03251
1978 CAT 966C wheel loader, 5’ log forks, 6 cyl diesel, s/n: 76J12959
CAT 980B wheel loader w/ 6’ log forks, 3f/3r, CAT 3306PC 6 cyl diesel, s/n: 89P7012
1994 CAT 307 hydraulic excavator w/ AMULET hydraulic log grapple, steel tracks, MITSUBISHI 4 cyl diesel, enclosed cab, 68” stick, 5700 hrs, s/n: 9ZL01092
KOMATSU PC75UU-2 hydraulic excavator, 70” stick, offset boom, 91” blade, rubber tracks, KOMATSU 4 cyl diesel, zero clearance, 3300 hrs, s/n: 6376
1988 CAT 229 log loader, CAT 3208 6 cyl diesel, YOUNG 360 degree grapple, 115” stick, 13,600 hrs, s/n: 1GF00590
CAT 920 wheel loader w/forklift mast attachment, 4x4, 48” lumber forks, side shift, 2-stage mast, CAT 4 cyl diesel,s/n: 6235863
CAT 920 wheel loader w/forklift mast attachment, 4x4, 50” lumber forks, side shift, 2-stage mast, CAT 4 cyl diesel,s/n: 62K3565
1974 GROVE RT6OS rough terrain hydraulic crane, 40,000 lb capacity, 24’ - 78’ 4 section boom, PAT alarm system, 4 stabilizers, 3f/3r, 4 cyl diesel, 1900 hrs,
s/n: 30027
CAT V180B 18,000 lb forklift, dual pneumatic tires, side shift, 52” lumber forks, 2 stage mast, enclosed cab, CAT 3208 4 cyl diesel, 19,600 hrs, s/n: 68Y01156
CAT DP30 6000 lb forklift, pneumatic tires, 3 stage mast, side shift, 4’ forks, 4 cyl diesel, 900 hrs, s/n: 7BM00837