docbrowning diameter pin shear
download 
Report Transcription
browning diameter pin shear
...OFFERS THE WORLD'S LARGEST SELECTION OF APPLICATION "MATCHED, SHAFT-READY SPROCKETS" That's Your Assurance Of Maximum Drive Efficiency At The Lowest Evaluated Cost. You can choose from the world's largest selection of high-quality, shaft ready sprockets to solve all your application problems. In-stock hardened sprockets, a Browning specialty, are guaranteed to last at least twice as long as the standard (unhardened) mild steel sprockets they replace. The result is increased chain life and reduced downtime. Additionally, you have the industry's broadest selection of sprocket mounting choices. Sprockets are available with three types of bushings to ensure secure mounting to shaft: • • • • • • • BROWNING SPLIT TAPER® Bushing — available in inch and metric sizes, as well as with spline bores; bore range 1/4-10". Q-D® Bushing in 1/16 inch increments and metric sizes. TAPER BORE in the same configurations. Finished Bore Sprockets are available with Hardened Teeth and 2 Setscrews for driver size sprockets, (30 teeth and smaller). Minimum Bore Sprockets are provided from stock to allow for our customers, requirements for simple modifications with same day delivery service. Browning continues to provide custom sprockets for a variety of applications up through 60" diameters. The combination of the above provides one of the broadest selections of stock sprockets in the industry. BROWNING SPLIT TAPER® Bushing Q-D® Bushing TAPER BORE Bushing STANDARD & HARDENED SPROCKETS No. Strands Bushing Type Pitch Range Bore Range Hardened Teeth 1 35-200 3/8-5" Up to 40 teeth 2 35-200 3/8-5 3 35-160 1/2-5 Finished Bore 1 35-100 3/8-2 7/16 Type B Min. Bore 1 25-200 1/4-6 3/4 2 35-200 1/2-8 1/4 3 40-200 1/2-8 3/8 1 25-200 Type A Steel Plate Up to 30 teeth OTHER SPROCKETS Double Single Sprockets 40-100 3/8-3 3/4 Extended Pitch Sprockets 2040-2080 3/8-2 11/16 2042-2082 5/8-3 Shear Pin Sprockets & Hubs 40-160 3/8-5 Torque Limiters & Sprockets 35-80 1/2-2 1/2 All To ensure optimum quality and reliability, Browning uses precision gear checking quality techniques in manufacturing these sprockets. Bushing type hardened sprocket and Browning's exclusive warranty (to last twice as long as a standard sprocket). 25, 35, 41 Stock Sprocket Listing — Table No. 1 No. 25 No. of Teeth Stock Sprockets for No. 35 Single Roller Chain Minimum Bore Split Taper Bushing Page H-10 Page H-10 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 30 32 35 36 40 42 45 48 52 54 60 68 70 72 78 80 84 95 96 102 112 — 25B9 25B10 25B11 25B12 25B13 25B14 25B15 25B16 25B17 25B18 25B19 25B20 25B21 25B22 25B23 25B24 25B25 25B26 — 25B28 25B30 25B32 — 25B36 25B40 — 25B45 25B48 — 25B54 25B60 — 25B70 25B72 — — — — — — — Taper Bore Finished Bushing Bore Hardened Hardened Q-D Bushing 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Type A Plate Minimum Bore Page H-11 Page H-56 Page H-11 Page H-11 Page H-12 Page H-12 — — — — — — — — — — — — — — 35G15 — 35G16 — 35G17 — 35G18 — 35G19, 35H19 35JA19 35H20 35JA20 35H21 35JA21 35H22 35JA22 35H23 35JA23 35H24 35JA24 35H25 35JA25 35H26 35JA26 35H27 35JA27 35H28 35JA28 35H30 35JA30 35H32 35JA32 35H35 35JA35 35H36 35SH36 35H40 35SH40 35H42 35SH42 35H45 35SH45 35H48 35SH48 — — 35H54 35SH54 35H60 35SH60 — — 35H70 — 35H72 35SH72 — — 35H80 35SH80 35H84 35SH84 — — 35H96 35SH96 — — 35H112 35SH112 — — — — — — — — — — 35TB18 35TB19 35TB20 35TB21 35TB22 35TB23 35TB24 35TB25 35TB26 — 35TB28 35TB30 35TB32 35TB35 35TB36 35TB40 35TB42 35TB45 35TB48 — 35TB54 35TB60 — 35TB70 35TB72 — 35TB80 35TB84 — 35TB96 — 35TB112 — H359 H3510 H3511 H3512 H3513 H3514 H3515 H3516 H3517 H3518 — H3520 — — — H3524 H3525 — — — H3530 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 3532 — 3536 3540 3542 3545 3548 — — 3560 — — — — — — — — — — — — — — — — — 35A15 35A16 35A17 35A18 35A19 35A20 35A21 35A22 35A23 35A24 35A25 35A26 35A27 35A28 35A30 35A32 35A35 35A36 35A40 35A42 35A45 35A48 — 35A54 35A60 — 35A70 35A72 — 35A80 35A84 — 35A96 — 35A112 35B8 35B9 35B10 35B11 35B12 35B13 35B14 35B15 35B16 35B17 35B18 35B19 35B20 35B21 35B22 35B23 35B24 35B25 35B26 35B27 35B28 35B30 35B32 35B35 35B36 35B40 35B42 35B45 35B48 — 35B54 35B60 — 35B70 35B72 — 35B80 35B84 — 35B96 — 35B112 Q-D Bushing Taper Bore Bushing Minimum Bore Page H-12 Page H-56 Page H-13 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — D35SDS68 — D35SDS72 D35SDS76 — D35SK84 — — — — — — — — — — — D35TB19 D35TB20 D35TB21 D35TB22 — D35TB24 — D35TB26 — — D35TB30 D35TB32 D35TB35 — D35TB40 — D35TB45 D35TB48 — D35TB54 D35TB60 — D35TB70 — — D35TB80 — — D35TB96 — D35TB112 — — — — D35B12 D35B13 D35B14 D35B15 D35B16 D35B17 D35B18 D35B19 D35B20 D35B21 D35B22 D35B23 D35B24 D35B25 D35B26 — — D35B30 — — D35B36 — D35B42 — D35B48 D35B52 — D35B60 D35B68 — D35B72 D35B76 — D35B84 — — — — — — Stock Sprockets for No. 41 Roller Chain Table No. 2 No. of Teeth Finished Bore Stock Sprockets for No. 35 Double Split Taper Bushing Type Q-D Bushing Type Taper Bore Bushing Finished Bore Type Type A Plate Minimum Bore Page H-13 Page H-14 Page H-56 Page H-14 Page H-15 Page H-15 — — — — — — 41G12 — 41G14 41H15 41H16 41H17 41H18 41H19 41H20 41H21 41H22 41H23 41H24 41H25 41H26 — — — — — — — — — 41JA15 41JA16 41JA17 41JA18 41JA19 41SH20 41SH21 41SH22 41SH23 41SH24 41SH25 41SH26 — — — — — — — — 41TB14 41TB15 41TB16 41TB17 41TB18 41TB19 41TB20 41TB21 41TB22 41TB23 41TB24 41TB25 41TB26 — — — 419 4110 4111 4112 4113 4114 4115 4116 4117 4118 4119 4120 4121 4122 — 4124 4125 — — — — — — — — — — 41A15 41A16 41A17 41A18 41A19 41A20 41A21 41A22 41A23 41A24 41A25 41A26 41B6 41B7 41B8 41B9 41B10 41B11 41B12 41B13 41B14 41B15 41B16 41B17 41B18 41B19 41B20 41B21 41B22 41B23 41B24 41B25 41B26 No. of Teeth 27 28 30 32 35 36 40 42 45 48 54 60 70 72 80 84 96 112 Split Taper Bushing Type Q-D Bushing Type Taper Bore Bushing Finished Bore Type Type A Plate Minimum Bore Page H-13 Page H-14 Page H-56 Page H-14 Page H-15 Page H-15 41H27 41H28 41H30 41H32 41H35 41P36(P1) 41P40(P1) 41P42(P1) 41P45(P1) 41P48(P1) 41P54(P1) 41P60(P1) 41P70(P1) 41P72(P1) 41P80(P1) 41P84(P1) 41P96(P1) 41P112(P1) 41SH27 41SH28 41SH30 41SH32 41SH35 41SDS36 41SDS40 41SDS42 41SDS45 41SDS48 41SDS54 41SDS60 41SK70 41SK72 41SK80 41SK84 41SK96 41SK112 — 41TB28 41TB30 41TB32 41TB35 41TB36 41TB40 — 41TB45 41TB48 41TB54 41TB60 41TB70 41TB72 41TB80 — 41TB96 — — — 4130 — 4135 4136 — 4142 — — 4154 — — — — — — — 41A27 41A28 41A30 41A32 41A35 41A36 41A40 41A42 41A45 41A48 41A54 41A60 41A70 41A72 41A80 41A84 41A96 41A112 41B27 41B28 41B30 41B32 41B35 41B36 41B40 41B42 41B45 41B48 41B54 41B60 41B70 41B72 41B80 41B84 41B96 41B112 H-2 Stock Sprocket Listing — Stock Sprockets for No. 40 Single Roller Chain Table No. 1 No. of Teeth 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 64 70 72 80 84 96 112 Split Taper Bushing Hardened Page H-16 — — — — H40G12 H40G13 H40G14 H40H15 H40H16 H40H17 H40H18, H40P18(P1) H40H19, H40P19(P1) H40H20, H40P20(P1) H40H21, H40P21(P1) H40H22, H40P22(P1) H40H23, H40P23(P1) H40H24, H40P24(P1) H40H25, H40P25(P1) H40H26, H40P26(P1) H40P27(P1) H40H28, H40P28(P1) H40P29(P1) H40H30, H40P30(P1) — H40H32 H40H33 — H40H35 H40H36 — H40H38 — H40H40 — — — — — — — — — — — — — — — — — — — — — — — — — — — Table No. 2 Q-D Bushing Hardened Page H-17 — — — — — — — H40JA15 H40JA16 H40JA17 H40JA18 H40JA19 H40SH20 H40SH21 H40SH22 H40SH23 H40SH24 H40SH25 H40SH26 H40SH27 H40SH28 — H40SH30 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Taper Bore Split Taper Q-D Taper Bore Finished Finished Bushing Bushing Bushing Bushing Bore Bore Hardened Type Type Type Hardened Page H-57 Page H-16 & H-17 Page H-17 Page H-57 Page H-18 Page H-18 — — — — — — — — — — H409 — — — — — H4010 — — — — — H4011 — — — — — H4012 — — — — — H4013 — H40TB14 — — — H4014 — H40TB15 — — — H4015 — H40TB16 — — — H4016 — H40TB17 — — — H4017 — H40TB18 — — — H4018 — H40TB19 — — — H4019 — H40TB20 — — — H4020 — H40TB21 — — — H4021 — H40TB22 — — — H4022 — H40TB23 — — — H4023 — H40TB24 — — — H4024 — H40TB25 — — — H4025 — H40TB26 — — — H4026 — — — — — H4027 — H40TB28 — — — H4028 — — — — — H4029 — H40TB30 — 40SH30 40TB30 H4030 — — 40P31(P1) — — — 4031 — 40P32(P1) 40SH32 40TB32 — 4032 — 40P33(P1) — — — 4033 — 40P34(P1) — — — 4034 — 40P35(P1) 40SH35 40TB35 — 4035 — 40P36(P1) 40SDS36 40TB36 — 4036 — 40P37(P1) — — — 4037 — 40P38(P1) — — — 4038 — — — — — — 40SDS40 40TB40 — 4040 — 40P40(P1) — 40P41(P1) — — — — — 40P42(P1) 40SDS42 40TB42 — 4042 — — — — — — — 40P44(P1) — — — 4044 — 40P45(P1) 40SDS45 40TB45 — 4045 — — — — — — — 40P47(P1) — — — — — 40P48(P1) 40SDS48 40TB48 — 4048 — — — — — — — 40P50(P1) — — — — — — — — — 4051 — — — — — — — — — — — — — 40P54(P1) 40SDS54 40TB54 — 4054 — — — — — — — 40P56(P1) — — — 4056 — — — — — — — — — — — — — — — — — — — 40P60(P1), 40Q60(Q1) 40SDS60 40TB60 — 4060 — — — — — — — 40P70(P1), 40Q70(Q1) 40SK70 40TB70 — 4070 — 40Q72(Q1) 40SK72 40TB72 — — — 40Q80(Q1) 40SK80 40TB80 — 4080 — 40Q84(Q1) 40SK84 40TB84 — — — 40Q96(Q1) 40SK96 40TB96 — — — 40Q112(Q1) 40SK112 40TB112 — — Type “A” Plate Minimum Bore Page H-18 — — — — 40A12 40A13 40A14 40A15 40A16 40A17 40A18 40A19 40A20 40A21 40A22 40A23 40A24 40A25 40A26 40A27 40A28 40A29 40A30 40A31 40A32 40A33 40A34 40A35 40A36 40A37 40A38 40A39 40A40 40A41 40A42 40A43 40A44 40A45 40A46 40A47 40A48 40A49 40A50 40A51 40A52 40A53 40A54 40A55 40A56 40A57 40A58 40A59 40A60 40A64 40A70 40A72 40A80 40A84 40A96 40A112 Page H-19 40B8 40B9 40B10 40B11 40B12 40B13 40B14 40B15 40B16 40B17 40B18 40B19 40B20 40B21 40B22 40B23 40B24 40B25 40B26 40B27 40B28 — 40B30 — 40B32 40B33 40B34 40B35 40B36 — 40B38 — 40B40 40B41 40B42 — — 40B45 40B46 40B47 40B48 — 40B50 — — — 40B54 — — — — — 40B60 — 40B70 40B72 40B80 40B84 40B96 40B112 Stock Sprockets for No. 40 Double and Triple Roller Chain Split Taper Q-D Taper Bore Split Taper Minimum No. Bushing Bushing Bushing Bushing Bore of Type Type Type Type Teeth Page H-20 Page H-20 Page H-57 Page H-20 & H-21 Page H-21 11 — — — D40B11 — 12 — — — D40B12 — 13 — — — D40B13 — 14 — — — D40B14 — 15 D40H15 — D40TBA15 D40B15 — 16 D40H16 — D40TBA16 D40B16 — 17 D40H17 — D40TBA17 D40B17 18 D40P18(P1) — D40TB18 D40B18 T40P18(P1) 19 D40P19(P1) — D40TB19 D40B19 T40P19(P1) 20 D40P20(P1) — D40TB20 D40B20 T40P20(P1) 21 D40P21(P1) — D40TB21 D40B21 — 22 D40P22(P1) — — D40B22 — 23 D40P23(P1) — D40TB23 D40B23 T40P23(P1) 24 D40P24(P1) — — D40B24 T40P24(P1) 25 D40P25(P1) — D40TB25 D40B25 T40P25(P1) 26 D40P26(P1) — — D40B26 — 27 — — — D40B27 T40P27(P1) 28 D40P28(P1) — — D40B28 — 30 D40P30(P1) — D40TB30 D40B30 T40Q30(Q1) H-3 40 Split Taper Q-D Taper Bore Split Taper Q-D Minimum Bushing Bushing Bushing Bushing Bushing Bore Type Type Type Type Type Page H-20 Page H-20 Page H-57 Page H-20 & H-21 Page H-21 Page H-21 32 D40Q32(Q1) — — D40B32 — — 35 D40Q35(Q1) — — D40B35 T40Q35(Q1) — 36 D40Q36(Q1) D40SK36 D40TB36 D40B36 T40Q36(Q1) T40SK36 40 D40Q40(Q1) D40SK40 — D40B40 — — 42 D40Q42(Q1) D40SK42 D40TB42 D40B42 T40Q42(Q1) T40SK42 45 D40Q45(Q1) D40SK45 — D40B45 T40Q45(Q1) T40SK45 48 D40Q48(Q1) D40SK48 D40TB48 D40B48 T40Q48(Q1) T40SK48 52 D40Q52(Q1) D40SK52 D40TB52 D40B52 T40Q52(Q1) T40SK52 54 D40Q54(Q1) D40SK54 — D40B54 T40Q54(Q1) — 60 D40Q60(Q1) D40SK60 D40TB60 D40B60 T40Q60(Q1) T40SK60 68 D40Q68(Q1) D40SF68 D40TB68 D40B68 T40Q68(Q1) T40SF68 72 D40Q72(Q1) D40SF72 — D40B72 T40Q72(Q1) T40SF72 76 D40Q76(Q1) D40SF76 D40TB76 D40B76 T40Q76(Q1) — 84 D40Q84(Q1) D40SF84 D40TB84 D40B84 T40Q84(Q1) T40SF84 95 D40Q95(Q1) D40SF95 — — T40Q95(Q1) — 96 D40Q96(Q1) D40SF96 — D40B96 — — 102 D40Q102(Q1) — — D40B102 T40Q102(Q1) — 112 D40Q112(Q1) — — D40B112 — — No. of Teeth Stock Sprocket Listing Table No. 1 Stock Sprockets for No. 50 Single Roller Chain Split Taper Q-D Taper Bore Q-D Taper Bore Finished Split Taper No. Bushing Bushing Bushing Bushing Bushing Bore Bushing Type of Hardened Hardened Hardened Type Type Hardened Teeth Page H-22 Page H-23 Page H-58 Page H-22 & H-23 Page H-24 Page H-58 Page H-24 8 — — — — — — — 9 — — — — — — H509 10 — — — — — — H5010 11 H50G11 — — — — — H5011 12 H50G12 H50JA12 H50TB12 — — — H5012 13 H50G13, H50H13 H50JA13 H50TB13 — — — H5013 14 H50H14 H50JA14 H50TB14 — — — H5014 15 H50H15, H50P15(P1) H50JA15 H50TB15 — — — H5015 16 H50H16, H50P16(P1) H50JA16 H50TB16 — — — H5016 17 H50H17, H50P17(P1) H50SH17 H50TB17 — — — H5017 18 H50H18, H50P18(P1) H50SH18 H50TB18 — — — H5018 19 H50H19, H50P19(P1) H50SH19 H50TB19 — — — H5019 20 H50H20, H50P20(P1) H50SDS20 H50TB20 — — — H5020 21 H50H21, H50P21(P1) H50SDS21 H50TB21 — — — H5021 22 H50H22, H50P22(P1) H50SDS22 H50TB22 — — — H5022 — — — H5023 23 H50H23, H50P23, H50Q23 H50SDS23 H50TB23 — — — H5024 24 H50H24, H50P24, H50Q24 H50SDS24 H50TB24 — — — H5025 25 H50H25, H50P25, H50Q25 H50SDS25 H50TB25 26 H50H26, H50P26, H50Q26 H50SDS26 H50TB26 — — — H5026 — — — H5027 27 H50H27, H50P27, H50Q27 H50SDS27 H50TB27 — — — H5028 28 H50H28, H50P28, H50Q28 H50SDS28 H50TB28 29 H50P29(P1) — — — — — H5029 — 50SDS30 — H5030 30 H50H30, H50P30, H50Q30 H50SDS30 H50TB30 31 — — — 50P31(P1) — — — 50P32(P1), 50Q32(Q1) 50SDS32 50TB32 — 32 H50H32 — — 33 H50H33 — — 50P33(P1) — — — 34 H50H34 — — 50P34(P1) — — — 50P35(P1), 50Q35(Q1) 50SDS35 50TB35 — 35 H50H35 — — 50P36(P1), 50Q36(Q1) 50SDS36 50TB36 — 36 H50H36 — — 37 — — — 50Q37(Q1) — — — 38 H50H38 — — 50Q38(Q1) — — — 39 — — — 50Q39(Q1) — — — 40 H50H40 — — 50Q40(Q1) 50SDS40 50TB40 — 41 — — — 50Q41(Q1) — — — 42 — — — 50Q42(Q1) 50SDS42 50TB42 — 43 — — — — — — — 44 — — — 50Q44(Q1) — — — 45 — — — 50Q45(Q1) 50SDS45 50TB45 — 46 — — — — — — — 47 — — — 50Q47(Q1) — — — 48 — — — 50Q48(Q1) 50SDS48 50TB48 — 49 — — — — — — — 50 — — — 50Q50(Q1) — — — 51 — — — — — — — 52 — — — — — — — 53 — — — — — — — 54 — — — 50Q54(Q1) 50SK54 50TB54 — 55 — — — — — — — 56 — — — 50Q56(Q1) — — — 57 — — — — — — — 58 — — — — — — — 59 — — — — — — — 60 — — — 50Q60(Q1) 50SK60 50TB60 — 70 — — — 50Q70(Q1) 50SK70 50TB70 — 72 — — — 50Q72(Q1) 50SK72 50TB72 — 76 — — — — — — — 80 — — — 50Q80(Q1) 50SF80 50TB80 — 84 — — — 50Q84(Q1) 50SF84 50TB84 — 95 — — — — — — — 96 — — — 50Q96(Q1) 50SF96 50TB96 — 112 — — — 50Q112(Q1) 50SF112 50TB112 — Table No. 2 Split Taper Q-D No. Bushing Bushing of Type Type Teeth Page H-26 Page H-27 11 — — 12 — — 13 — — 14 D50H14 — 15 D50P15(P1) — 16 D50P16(P1) — 17 D50P17(P1) — 18 D50P18(P1) — 19 D50P19(P1) — 20 D50P20(P1) — 21 D50P21(P1) — 22 D50P22(P1) — 23 D50P23(P1) — 24 D50Q24(Q1) — 25 D50Q25(Q1) — 26 D50Q26(Q1) — 27 D50Q27(Q1) — 28 D50Q28(Q1) — 30 D50Q30(Q1) — 50 Finished Bore Page H-24 — — — — — — — — — — — — — — — — — — — — — — — — 5032 5033 5034 5035 5036 — 5038 5039 5040 5041 5042 — — 5045 — — 5048 5049 5050 — — — — — — — — — 5060 — — — — — — — — Type “A” Plate Minimum Bore Page H-25 Page H-25 & H-26 — 50B8 — 50B9 50A10 50B10 50A11 50B11 50A12 50B12 50A13 50B13 50A14 50B14 50A15 50B15 50A16 50B16 50A17 50B17 50A18 50B18 50A19 50B19 50A20 50B20 50A21 50B21 50A22 50B22 50A23 50B23 50A24 50B24 50A25 50B25 50A26 50B26 50A27 50B27 50A28 50B28 50A29 50B29 50A30 50B30 50A31 50B31 50A32 50B32 50A33 50B33 50A34 50B34 50A35 50B35 50A36 50B36 50A37 — 50A38 50B38 50A39 50B39 50A40 50B40 50A41 — 50A42 50B42 50A43 — 50A44 50B44 50A45 50B45 50A46 — 50A47 — 50A48 50B48 50A49 — 50A50 50B50 50A51 — 50A52 50B52 50A53 — 50A54 50B54 50A55 — 50A56 — 50A57 — 50A58 — 50A59 — 50A60 50B60 50A70 50B70 50A72 50B72 50A76 50B76 50A80 50B80 50A84 50B84 50A95 50B95 50A96 50B96 50A112 50B112 Stock Sprockets for No. 50 Double and Triple Roller Chain Taper Bore Minimum Split Taper Q-D Bushing Bushing Bushing Bore Type Type Type Page H-58 Page H-27 Page H-28 Page H-27 — D50B11 — — — D50B12 — — — D50B13 — — D50TBA14 D50B14 — — D50TBA15 D50B15 T50P15(P2) — D50TBA16 D50B16 T50P16(P2) — D50TBA17 D50B17 T50P17(P2) — D50TBA18 D50B18 T50P18(P2) — D50TBA19 D50B19 T50P19(P1) — D50TB20 D50B20 T50P20(P1) — D50TB21 D50B21 T50P21(P1) — — D50B22 — — — D50B23 T50P23(P1) — — D50B24 T50Q24(Q1) — D50TB25 D50B25 T50Q25(Q1) — — D50B26 T50Q26(Q1) — — — — — — — T50Q28(Q1) — D50TB30 D50B30 T50Q30(Q1) — Split Taper Q-D Taper Bore Bushing Bushing Bushing Type Type Type Page H-26 Page H-27 Page H-58 32 D50Q32(Q1) — — 35 D50Q35(Q1) — — 36 D50Q36(Q1) D50SK36 D50TB36 40 D50Q40(Q1) — — 42 D50Q42(Q1) D50SK42 D50TB42 45 D50Q45(Q1) — — 48 D50Q48(Q1) D50SK48 D50TB48 52 D50Q52(Q1) D50SF52 D50TB52 54 D50Q54(Q1) D50SF54 — 60 D50Q60(Q1) D50SF60 D50TB60 68 — D50SF68 D50TB68 72 D50Q72(Q1) D50SF72 — 76 D50Q76(Q1) D50SF76 D50TB76 84 D50Q84(Q1) D50SF84 D50TB84 95 D50R95(R1) D50SF95 D50TB95 96 D50R96(R1) — — 102 D50R102(R1) D50SF102 — 112 D50R112(R1) D50SF112 — No. of Teeth Minimum Bore Page H-27 D50B32 D50B35 D50B36 D50B40 D50B42 D50B45 D50B48 D50B52 D50B54 D50B60 D50B68 D50B72 D50B76 D50B84 D50B95 D50B96 D50B102 D50B112 Split Taper Q-D Bushing Bushing Type Type Page H-28 Page H-27 T50Q32(Q1) — T50Q35(Q1) — T50Q36(Q1) T50SK36 T50Q40(Q1) — T50Q42(Q1) T50SK42 — — T50Q48(Q1) T50SK48 T50Q52(Q1) T50SF52 — — T50R60(R1) T50SF60 T50R68(R1) — T50R72(R1) T50SF72 T50R76(R1) T50R84(R1) T50SF84 T50R95(R1) — — — T50R102(R1) T50SF102 — — H-4 Stock Sprocket Listing Table No. 1 No. of Teeth 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 64 65 66 68 70 72 76 80 84 95 96 112 Split Taper Bushing Hardened Page H-29 — — H60G10 H60H11 H60H12 H60H13, H60P13(P1) H60H14, H60P14(P1) H60H15, H60P15(P1) H60H16, H60P16(P1) H60H17, H60P17(P1) H60H18, H60P18(P1) H60H19, H60P19(P1) H60H20, H60P20, H60Q20 H60P21(P1), H60Q21(Q1) H60H22, H60P22, H60Q22 H60P23(P1), H60Q23(Q1) H60H24, H60P24, H60Q24 H60P25(P1), H60Q25(Q1) H60P26(P1), H60Q26(Q1) H60P27(P1), H60Q27(Q1) H60P28(P1), H60Q28(Q1) H60Q29(Q1) H60P30(P1), H60Q30(Q1) — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Table No. 2 Split Taper Bushing Type Stock Sprockets for No. 60 Single Roller Chain Q-D Bushing Hardened Page H-30 — — — H60JA11 H60JA12 H60JA13 H60SH14 H60SH15 H60SH16 H60SDS17 H60SDS18 H60SDS19 H60SDS20 H60SDS21 H60SDS22 H60SDS23 H60SDS24 H60SDS25 H60SK26 H60SK27 H60SK28 — H60SK30 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Taper Bore Split Taper Q-D Taper Bore Finished Finished Type “A” Minimum Bushing Bushing Bushing Bushing Bore Bore Plate Bore Hardened Type Type Type Hardened Page H-59 Page H-29 Page H-30 Page H-59 Page H-31 Page H-31 Page H-31 Page H-32 — — — — — — — 60B8 — — — — H609 — — 60B9 — — — — H6010 — 60A10 60B10 H60TB11 — — — H6011 — 60A11 60B11 H60TB12 — — — H6012 — 60A12 60B12 H60TB13 — — — H6013 — 60A13 60B13 H60TB14 — — — H6014 — 60A14 60B14 H60TB15 — — — H6015 — 60A15 60B15 H60TB16 — — — H6016 — 60A16 60B16 H60TB17 — — — H6017 — 60A17 60B17 H60TB18 — — — H6018 — 60A18 60B18 H60TB19 — — — H6019 — 60A19 60B19 H60TB20 — — — H6020 — 60A20 60B20 H60TB21 — — — H6021 — 60A21 60B21 H60TB22 — — — H6022 — 60A22 60B22 H60TB23 — — — H6023 — 60A23 60B23 H60TB24 — — — H6024 — 60A24 60B24 H60TB25 — — — H6025 — 60A25 60B25 H60TB26 — — — H6026 — 60A26 60B26 H60TB27 — — — H6027 — 60A27 60B27 H60TB28 — — — H6028 — 60A28 60B28 — — — — H6029 — 60A29 60B29 H60TB30 — 60SK30 — H6030 — 60A30 60B30 — 60Q31(Q1) — — — — 60A31 60B31 — 60Q32(Q1) 60SK32 60TB32 — 6032 60A32 60B32 — 60Q33(Q1) — — — — 60A33 60B33 — 60Q34(Q1) — — — — 60A34 60B34 — 60Q35(Q1) 60SK35 60TB35 — 6035 60A35 60B35 — 60Q36(Q1) 60SK36 60TB36 — 6036 60A36 60B36 — 60Q37(Q1) — — — — 60A37 60B37 — 60Q38(Q1) — — — — 60A38 60B38 — 60Q39(Q1) — — — — 60A39 60B39 — 60Q40(Q1) 60SK40 60TB40 — 6040 60A40 60B40 — 60Q41(Q1) — — — — 60A41 60B41 — 60Q42(Q1) 60SF42 60TB42 — — 60A42 60B42 — — — — — — 60A43 60B43 — — — — — — 60A44 60B44 — 60Q45(Q1) 60SF45 60TB45 — 6045 60A45 60B45 — — — — — 6046 60A46 — — 60Q47(Q1) — — — — 60A47 60B47 — 60Q48(Q1) 60SF48 60TB48 — — 60A48 60B48 — — — — — — 60A49 — — 60Q50(Q1) — — — — 60A50 60B50 — — — — — — 60A51 — — — — — — — 60A52 — — — — — — — 60A53 — — 60Q54(Q1) — 60TB54 — — 60A54 60B54 — — — — — — 60A55 — — 60Q56(Q1) — — — — 60A56 60B56 — — — — — — 60A57 — — — — — — — 60A58 — — — — — — — 60A59 — — 60Q60(Q1) 60SF60 60TB60 — — 60A60 60B60 — — — — — — 60A64 60B64 — — — — — — 60A65 60B65 — — — — — — 60A66 — — — — — — — 60A68 60B68 — 60Q70(Q1), 60R70(R1) 60SF70 60TB70 — — 60A70 60B70 — 60Q72(Q1), 60R72(R1) 60SF72 60TB72 — — 60A72 60B72 — — — — — 6076 60A76 60B76 — 60Q80(Q1), 60R80(R1) 60SF80 60TB80 — — 60A80 60B80 — 60Q84(Q1), 60R84(R1) 60SF84 60TB84 — — 60A84 60B84 — — — — — — 60A90 60B90 — 60Q96(Q1), 60R96(R1) 60SF96 — — — 60A96 60B96 — 60Q112(Q1), 60R112(R1) — — — 60A112 60B112 Stock Sprockets for No. 60 Double and Triple Roller Chain Q-D Taper Bore Minimum Split Taper Q-D Split Taper Q-D Taper Bore Bushing Bushing Bushing Bushing Bushing Bushing Bushing No. No. Bore Type Type Type Type Type Type Type of of Teeth H-33 Page H-34 Page H-34 Teeth Page H-33 Page H-33 Page H-59 Page H-33 Page H-33 Page H-59 Page & H34 11 — — — D60B11 — — 30 D60Q30(Q1) — D60TB30 12 — — — D60B12 — — 32 D60Q32(Q1) — — 13 D60P13(P1) — D60TB13 D60B13 T60P13(P2) — 35 D60Q35(Q1) — — 14 D60P14(P1) D60SH14 D60TB14 D60B14 T60P14(P2) — 36 D60Q36(Q1) D60SF36 D60TB36 15 D60P15(P1) — D60TB15 D60B15 T60P15(P2) — 40 D60Q40(Q1) — — 16 D60P16(P1) — D60TB16 D60B16 T60P16(P1) — 42 D60Q42(Q1) D60E42 D60TB42 17 D60P17(P1) — D60TB17 D60B17 T60Q17(Q1) — — D60R42(R1) — — 18 D60P18(P1) — D60TBA18 D60B18 T60Q18(Q1) — 45 D60R45(R1) D60E45 D60TB45 19 D60P19(P1) — D60TBA19 D60B19 T60Q19(Q1) — 48 D60R48(R1) — — 20 D60P20(P1) — D60TB20 D60B20 T60Q20(Q1) — 52 D60R52(R1) D60E52 D60TB52 21 D60Q21(Q1) — D60TB21 D60B21 T60Q21(Q1) — 54 D60R54(R1) — — 22 D60Q22(Q1) D60SDS22 — D60B22 T60Q22(Q1) — 60 D60R60(R1) D60E60 D60TB60 23 D60Q23(Q1) — — D60B23 T60Q23(Q1) — 68 D60R68(R1) D60E68 D60TB68 24 D60Q24(Q1) — — D60B24 T60Q24(Q1) — 72 D60R72(R1) — — 25 D60Q25(Q1) — D60TB25 D60B25 T60Q25(Q1) — 76 D60R76(R1) D60E76 D60TB76 26 D60Q26(Q1) — — D60B26 T60Q26(Q1) — 84 D60R84(R1) — — 27 D60Q27(Q1) — — — T60Q27(Q1) — 95 D60R95(R1) D60E95 D60TB95 28 D60Q28(Q1) — — — T60Q28(Q1) — 96 D60R96(R1) — — H-5 60 Minimum Bore Page H-33 & H-34 D60B30 D60B32 D60B35 D60B36 D60B40 D60B42 — D60B45 — D60B52 — D60B60 D60C68 D60C72 D60C76 — D60C95 — Split Taper Bushing Type Q-D Bushing Type Page H-34 Page H-34 T60R30(R1) T60R32(R1) T60R35(R1) T60R36(R1) T60R40(R1) T60R42(R1) — — — T60R52(R1) — — T60S68(S1) — T60S76(S1) — T60S95(S1) — — — — T60E36 — T60E42 — — — T60E52 — — T60E68 — T60E76 — T60E95 — Stock Sprocket Listing Stock Sprockets for No. 80 Single Roller Chain Table No. 1 No. of Teeth 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 65 70 72 76 80 84 90 96 112 No. of Teeth 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Split Taper Bushing Hardened Q-D Taper Bore Bushing Bushing Hardened Hardened Split Taper Bushing Type Page H-35 Page H-36 Page H-60 Page H-35 — — — — — — — — H80TB10 H80H11, H80P11(P1) H80SH11 H80TB11 H80P12(P1) H80SH12 H80TB12 H80P13(P1) H80SDS13 H80TB13 H80P14(P1), H80Q14(Q1) H80SDS14 H80TB14 H80P15(P1), H80Q15(Q1) H80SK15 H80TB15 H80P16(P1), H80Q16(Q1) H80SK16 H80TB16 H80P17(P1), H80Q17(Q1) H80SK17 H80TB17 H80P18(P1), H80Q18(Q1) H80SK18 H80TB18 H80P19(P1), H80Q19(Q1) H80SK19 H80TB19 H80Q20(Q1) H80SF20 H80TB20 H80Q21(Q1) H80SF21 H80TB21 H80Q22(Q1) H80SF22 H80TB22 H80Q23(Q1) H80SF23 H80TB23 H80Q24(Q1) H80SF24 H80TB24 H80Q25(Q1) H80SF25 H80TB25 H80Q26(Q1) H80SF26 H80TB26 H80Q27(Q1) H80SF27 H80TB27 H80Q28(Q1) H80SF28 H80TB28 H80Q29(Q1) — — H80Q30(Q1) H80SF30 H80TB30 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Table No. 2 80 — — — — — — — — — — — — — — — — — — — — — — — 80Q31(Q1) 80Q32(Q1) 80Q33(Q1) 80Q34(Q1) 80Q35(Q1) 80Q36(Q1) 80Q37(Q1) 80Q38(Q1) 80R39(R1) 80Q40(Q1), 80R40(R1) 80R41(R1) 80Q42(Q1), 80R42(R1) — 80R44(R1) 80Q45(Q1), 80R45(R1) — — 80Q48(Q1), 80R48(R1) — 80R50(R1) — — — 80Q54(Q1), 80R54(R1) — 80R56(R1) — — — 80Q60(Q1), 80R60(R1) — 80Q70(Q1), 80R70(R1) 80Q72(Q1), 80R72(R1) — 80R80(R1) 80R84(R1) — 80R96(R1) 80S112(S1) Q-D Bushing Type Taper Bore Finished Bushing Bore Type Hardened Finished Bore Type “A” Plate Minimum Bore H-38 Page H-36 Page H-60 Page H-36 Page H-36 Page H-37 Page & H-38 — — — — — 80B8 — — H809 — 80A9 80B9 — — H8010 — 80A10 80B10 — — H8011 — 80A11 80B11 — — H8012 — 80A12 80B12 — — H8013 — 80A13 80B13 — — H8014 — 80A14 80B14 — — H8015 — 80A15 80B15 — — H8016 — 80A16 80B16 — — H8017 — 80A17 80B17 — — H8018 — 80A18 80B18 — — H8019 — 80A19 80B19 — — H8020 — 80A20 80B20 — — H8021 — 80A21 80B21 — — H8022 — 80A22 80B22 — — H8023 — 80A23 80B23 — — H8024 — 80A24 80B24 — — H8025 — 80A25 80B25 — — H8026 — 80A26 80B26 — — H8027 — 80A27 80B27 — — H8028 — 80A28 80B28 — — H8029 — 80A29 80B29 80SF30 — H8030 — 80A30 80B30 — — — — 80A31 80B31 80SF32 80TB32 — 8032 80A32 80B32 80SF33 — — — 80A33 80B33 80SF34 — — — 80A34 80B34 80SF35 80TB35 — 8035 80A35 80B35 80SF36 80TB36 — 8036 80A36 80B36 — — — — 80A37 80B37 — — — — 80A38 80B38 — — — — 80A39 80B39 — — 80A40 80B40 80SF40 80TB40 — — — — 80A41 80B41 80SF42 — — — 80A42 80B42 — — — — 80A43 — — — — — 80A44 80B44 80SF45 80TB45 — — 80A45 80B45 — — — — 80A46 80B46 — — — — 80A47 80B47 80SF48 80TB48 — — 80A48 80B48 — — — — 80A49 80B49 — — — — 80A50 80B50 — — — — 80A51 — — — — — 80A52 — — — — — 80A53 — — 80TB54 — — 80A54 80B54 — — — — 80A55 — — — — — 80A56 — — — — — 80A57 — — — — — 80A58 — — — — — 80A59 — — 80TB60 — — 80A60 80B60 — — — — 80A65 80B65 80E70 80TB70 — — 80A70 80C70 80E72 — — — 80A72 80C72 — — — — 80A76 80C76 — 80TB80 — — 80A80 80C80 — — — — 80A84 — — — — — 80A90 80C90 80E96 — — — 80A96 80C96 80F112 — — — 80A112 80C112 Stock Sprockets for No. 80 Double and Triple Roller Chain Split Taper Q-D Taper Bore Bushing Bushing Bushing Type Type Type Page H-38 & H-39 Page H-39 Page H-60 — — — — — — — — — D80P13(P1) — D80TBA13 D80Q14(Q2) — D80TBA14 D80Q15(Q2) — D80TBA15 D80Q16(Q1) — D80TBA16 D80Q17(Q1) — D80TBA17 D80Q18(Q1) — D80TBA18 D80Q19(Q2) — D80TB19 D80R20(R1) — D80TB20 D80R21R1) — D80TB21 D80R22(R1) — — D80R23(R1) — — D80R24(R1) — — D80R25(R1) — D80TB25 D80R26(R1) — — Taper Q-D Split Taper Minimum Split Bushing Bushing No. Bushing Bore of Type Type Type Teeth Page H-39 Page H-40 Page H-40 Page H-38 & H-39 D80B10 — — 27 D80R27(R1) D80B11 — — 28 D80R28(R1) D80B12 — — 30 D80R30(R1) D80B13 T80P13(P2) — 32 — D80B14 T80Q14(Q2) — 35 — D80B15 T80Q15(Q2) — 36 D80R36(R1) D80B16 T80Q16(Q2) — 40 — D80B17 T80Q17(Q2) — 42 D80R42(R1) D80B18 — — 45 D80R45(R1) D80B19 T80Q19(Q2) — 48 D80R48(R2) D80B20 T80R20(R1) — 52 D80R52(R2) D80B21 T80R21(R1) — 54 D80R54(R2) D80B22 T80R22(R1) — 60 D80R60(R2) D80B23 T80R23(R1) — 68 D80R68(R2) D80B24 T80R24(R1) — 72 D80R72(R2) D80B25 T80R25(R1) — 76 D80U76(U0) D80B26 T80R26(R1) — 95 D80U95(U0) Q-D Taper Bore Bushing Bushing Type Type Page H-39 Page H-60 — — — — — D80TB30 — — — — D80E36 D80TB36 — — D80E42 D80TB42 D80E45 D80TB45 — — D80E52 D80TB52 — — D80E60 D80TB60 D80E68 D80TB68 — — D80E76 D80TB76 — — Taper Q-D Minimum Split Bushing Bushing Bore Type Type Page H-39 Page H-40 Page H-40 — T80R27(R1) — — T80R28(R1) — D80B30 T80R30(R1) — D80B32 — — D80B35 — — D80B36 T80S36(S1) T80E36 D80B40 — — D80B42 T80S42(S1) T80E42 D80B45 T80S45(S1) T80E45 — — — D80C52 T80U52(U0) T80E52 — — — D80C60 T80U60(U0) T80F60 D80C68 T80U68(U0) T80F68 — — — D80C76 T80U76(U0) T80F76 D80C95 T80U95(U0) T80F95 H-6 Stock Sprocket Listing Stock Sprockets for No. 100 Single Roller Chain Table No. 1 No. of Teeth 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 70 72 76 80 84 90 96 Split Taper Bushing Hardened Page H-41 — — — — H100P11(P1) H100Q12(Q1) H100Q13(Q1) H100Q14(Q1) H100Q15(Q1) H100Q16(Q1) H100Q17(Q1) H100Q18(Q1) H100Q19(Q1) H100Q20(Q1) H100Q21(Q1) H100Q22(Q1) H100Q23(Q1) H100Q24(Q1), H100R24(R1) H100Q25(Q1) H100Q26(Q1) H100R26(R1) H100R27(R1) H100Q28(Q1) — H100Q30(Q1) — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Table No. 2 No. of Teeth 9 10 11 12 13 14 15 16 17 18 19 20 H-7 Split Taper Bushing Type Page H-43 — — D100P11(P1) D100Q12(Q2) D100Q13(Q2) D100Q14(Q1) D100Q15(Q1) D100Q17(Q1) D100R17(R1) D100R18(R1) D100R19(R1) D100R20(R1) 100 Q-D Bushing Hardened Page H-42 — — — — H100SDS11 H100SDS12 H100SK13 H100SK14 H100SF15 H100SF16 H100SF17 H100E18 H100E19 H100E20 H100E21 H100E22 H100E23 H100E24 H100E25 H100E26 H100E27 H100E28 — H100E30 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Taper Bore Bushing Hardened Page H-61 — — — — H100TB11 H100TB12 H100TB13 H100TB14 H100TB15 H100TB16 H100TB17 H100TB18 H100TB19 H100TB20 H100TB21 H100TB22 — H100TB24 — H100TB26 — H100TB28 — H100TB30 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Split Taper Bushing Type Page H-41 — — — — — — — — — — — — — — — — — — — — — — — — — 100Q32(Q1), 100R32(R1) — — 100Q35(Q1), 100R35(R1) 100R36(R1) — — — 100R40(R1) — 100R42(R1) — — 100R45(R1) — — 100R48(R1) — — — — — — — — — — — 100R60(R1) 100R70(R1) 100R72(R1) — 100R80(R1) 100R84(R1) — — Q-D Bushing Type Page H-42 — — — — — — — — — — — — — — — — — — — — — — — — — 100E32 — — 100E35 100E36 — — — 100E40 — 100E42 — — 100E45 — — 100E48 — — — — — 100E54 — — — — — 100E60 100F70 100F72 — 100F80 100F84 — — Taper Bore Bushing Type Page H-61 — — — — — — — — — — — — — — — — — — — — — — — — — 100TB32 — — 100TB35 100TB36 — — — 100TB40 — — — — 100TB45 — — 100TB48 — — — — — 100TB54 — — — — — 100TB60 — — — — — — — Type “A” Plate Minimum Bore Page H-42 100A7 100A8 100A9 100A10 100A11 100A12 100A13 100A14 100A15 100A16 100A17 100A18 100A19 100A20 100A21 100A22 100A23 100A24 100A25 100A26 100A27 100A28 100A29 100A30 100A31 100A32 100A33 100A34 100A35 100A36 100A37 100A38 100A39 100A40 100A41 100A42 100A43 100A44 100A45 100A46 100A47 100A48 100A49 100A50 100A51 100A52 100A53 100A54 100A55 100A56 100A57 100A58 100A59 100A60 100A70 100A72 100A76 100A80 100A84 100A90 100A96 Page H-43 — 100B8 100B9 100B10 100B11 100B12 100B13 100B14 100B15 100B16 100B17 100B18 100B19 100B20 100B21 100B22 100B23 100B24 100B25 100B26 100B27 100B28 100B29 100B30 — 100B32 — — 100B35 100B36 — — 100B39 100B40 — 100B42 — — 100B45 — — 100B48 — — — — — 100C54 — — — — — 100C60 100C70 100C72 100C76 100C80 100C84 100C90 100C96 Stock Sprockets for No. 100 Double and Triple Roller Chain Q-D Bushing Type Page H-44 — — — — — — — — — — — — Minimum Bore Page H-44 D100B9 D100B10 D100B11 D100B12 D100B13 D100B14 D100B15 D100B16 D100B17 D100B18 D100B19 D100B20 Q-D Bushing Type Page H-44 — — — — — — — — — — — — No. of Teeth 21 22 23 24 25 26 30 35 45 60 70 80 Split Taper Bushing Type Page H-43 D100R21(R1) D100R22(R1) — D100R24(R1) — — — D100R35(R1) D100S45(S1) D100S60(S1) D100S70(S1) D100S80(S1) Q-D Bushing Type Page H-44 — — — — — — — D100F35 D100F45 D100J60 D100J70 D100J80 Minimum Bore Page H-44 D100B21 D100B22 D100B23 D100B24 D100B25 D100B26 D100B30 D100C35 D100C45 D100C60 D100C70 D100C80 Q-D Bushing Type Page H-44 — — — — — — — T100F35 T100F45 T100J60 T100J70 T100J80 Stock Sprocket Listing — Stock Sprockets for No. 120 Single Roller Chain Table No. 1 No. of Teeth 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 30 32 34 35 36 40 42 45 48 54 60 70 80 90 Split Taper Bushing Hardened Q-D Bushing Hardened Taper Bore Bushing Hardened Split Taper Bushing Type Q-D Bushing Type Taper Bore Bushing Type Type “A” Plate Minimum Bore Page H-45 — — — H120Q11(Q1) H120Q12(Q1) H120Q13(Q1) H120Q14(Q1) H120Q15(Q1) H120R16(R1) H120R17(R1) H120R18(R1) H120R19(R1) H120R20(R1) H120R21(R1) H120R22(R1) H120R23(R1) H120R24(R1) H120R25(R1) H120R26(R1) — H120R28(R1) H120R30(R1) — — — — — — — — — — — — — Page H-46 — — — — H120SF12 H120SF13 H120SF14 H120SF15 H120E16 H120E17 H120E18 H120E19 H120E20 H120E21 H120E22 H120E23 H120E24 H120E25 H120E26 — H120E28 H120E30 — — — — — — — — — — — — — Page H-62 — — — — H120TB12 H120TB13 H120TB14 H120TB15 H120TB16 H120TB17 H120TB18 H120TB19 H120TB20 H120TB21 — — H120TB24 — H120TB26 — — H120TB30 — — — — — — — — — — — — — Page H-45 — — — — — — — — — — — — — — — — — — — — — — 120R32(R1) — 120R35(R2) 120R36(R2) 120R40 (R2), 120S40(S1) 120S42(S1) 120R45(R2), 120S45(S1) 120S48(S1) 120S54(S1) 120R60(R2), 120S60(S1) 120R70(R2), 120S70(S2) 120R80(R2), 120S80(S2) — Page H-46 — — — — — — — — — — — — — — — — — — — — — — 120F32 — 120F35 120F36 120F40 120F42 120F45 120F48 120F54 120J60 120J70 120J80 — Page H-62 — — — — — — — — — — — — — — — — — — — — — — — — 120TB35 120TB36 — — 120TB45 — — 120TB60 120TB70 120TB80 — Page H-46 120A8 120A9 120A10 120A11 120A12 120A13 120A14 120A15 120A16 120A17 120A18 120A19 120A20 120A21 120A22 120A23 120A24 120A25 120A26 120A27 120A28 120A30 120A32 120A34 120A35 120A36 120A40 120A42 120A45 120A48 120A54 120A60 120A70 120A80 120A90 Page H-47 — 120B9 120B10 120B11 120B12 120B13 120B14 120B15 120B16 120B17 120B18 120B19 120B20 120B21 120B22 120B23 120B24 120B25 120B26 — 120B28 120B30 120B32 — 120B35 120B36 120C40 120C42 120C45 120C48 120C54 120C60 120C70 120C80 — Stock Sprockets for No. 120 Double Chain Table No. 2 No. of Teeth 11 12 13 14 15 16 17 18 19 20 Split Taper Bushing Type Q-D Bushing Type Minimum Bore Page H-47 — — — — — — — — — — Page H-47 — — — — — — — — — — Page H-48 D120B11 D120B12 D120B13 D120B14 D120B15 D120B16 D120B17 D120B18 D120B19 D120B20 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 No. of Teeth 21 22 23 24 25 26 30 35 45 60 Split Taper Bushing Type Q-D Bushing Type Minimum Bore Page H-47 — — — — — — D120S30(S1) D120S35(S1) D120S45(S2) D120U60(U0) Page H-47 — — — — — — D120J30 D120J35 D120J45 — Page H-48 D120B21 D120B22 D120B23 D120B24 D120B25 D120B26 D120B30 D120C35 D120C45 D120C60 Stock Sprockets for No. 140 Single and Double Roller Chain Table No. 3 No. of Teeth 120 & 140 Split Taper Bushing Hardened Q-D Bushing Hardened Taper Bore Bushing Hardened Split Taper Bushing Type Q-D Bushing Type Taper Bore Bushing Type Type “A” Plate Minimum Bore Q-D Bushing Type Minimum Bore Page. H-48 H140Q11(Q1) H140Q12(Q1) H140R13(R1) H140R14(R1) H140R15(R1) H140R16(R1) H140R17(R1) H140R18(R1) H140R19(R1) H140R20(R1) H140R21(R1) H140R22(R1) H140R23(R1) H140R24(R1) H140R25(R1) H140R26(R1) Page H-49 H140SF11 H140SF12 H140SF13 H140E14 H140E15 H140E16 H140E17 H140E18 H140E19 H140E20 — — H140F23 H140F24 H140F25 H140F26 Page H-62 — H140TB12 H140TB13 H140TB14 H140TB15 H140TB16 H140TB17 H140TB18 H140TB19 — H140TB21 — — — — H140TB26 Page H-48 — — — — — — — — — — — — — — — — Page H-49 — — — — — — — — — — — — — — — — Page H-62 — — — — — — — — — — — — — — — — Page H-50 140A11 140A12 140A13 140A14 140A15 140A16 140A17 140A18 140A19 140A20 140A21 140A22 140A23 140A24 140A25 140A26 Page H-50 140B11 140B12 140B13 140B14 140B15 140B16 140B17 140B18 140B19 140B20 140B21 140B22 140B23 140B24 140B25 140B26 Page H-50 — — — — — — — — — — — — — — — — Page H-51 — — D140B13 D140B14 D140B15 D140B16 D140B17 D140B18 D140B19 D140B20 D140B21 D140B22 D140B23 D140B24 D140B25 D140B26 H-8 Stock Sprocket Listing — Table No. 1 No of Teeth 27 28 30 31 32 35 36 40 45 48 54 60 70 80 Stock Sprockets for No. 140 Single and Double Roller Chain (Continued) Split Taper Bushing Hardened Q-D Bushing Hardned Taper Bore Bushing Hardned Split Taper Bushing Type Q-D Bushing Type Taper Bore Bushing Type Type”A” Plate Minimum Bore Q-D Bushing Type Minimum Bore Page H-48 — — H140R30(R2) — — — — — — — — — — — — — Page H-49 — — H140F30 — — — — — — — — — — — — — Page H-62 — — — — — — — — — — — — — — — — Page H-48 & H-49 — — — — — 140R35(R2) 140R36(R2) 140S36(S1) 140R40(R2) 140S40(S1) 140S45(S1) 140S48(S2) 140S54(S2) 140S60(S2) 140S70(S2) 140S80(S2) Page H-49 — — — — — 140F35 140F36 — 140J40 — 140J45 140J48 — 140J60 — — Page H-62 — — — — — 140TB35 140TB36 — — — 140TB45 — — 140TB60 140TB70 — Page H-50 140A27 140A28 140A30 140A31 140A32 140A35 140A36 — 140A40 — 140A45 140A48 140A54 140A60 140A70 140A80 Page H-50 140B27 140B28 140B30 — 140B32 140C35 — — 140C40 — 140C45 140C48 140C54 140C60 140C70 140C80 Page H-50 — — — — — D140J35 — — — — D140J45 — — D140M60 — — Page H-51 — — — — — D140C35 — 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 30 35 36 40 45 54 60 70 80 Split Taper Bushing Hardened Q-D Bushing Hardned Taper Bore Bushing Hardned Split Taper Bushing Type Q-D Bushing Type Taper Bore Bushing Type Type”A” Plate Minimum Bore Q-D Bushing Type Minimum Bore Page H-51 — — — H160R11(R1) H160R12(R1) H160R13(R1) H160R14(R1) H160R15(R1) H160R16(R1) H160R17(R1) H160R18(R1) H160R19(R1) H160R20(R2) H160R21(R2) H160R22(R2) H160R23(R2) H160R24(R2) H160R25(R2) H160S26(S1) — H160S28(S2) H160S30(S2) — — — — — — — — — Page H-52 — — — — H160E12 H160E13 H160E14 H160F15 H160F16 H160F17 H160F18 H160F19 H160F20 H160F21 H160F22 H160F23 H160F24 H160F25 H160J26 — H160J28 H160J30 — — — — — — — — — Page H-63 — — — H160TB11 H160TB12 H160TB13 H160TB14 H160TB15 H160TB16 H160TB17 H160TB18 H160TB19 H160TB20 H160TB21 — — H160TB24 — H160TB26 — — — — — — — — — — — — Page H-51 — — — — — — — — — — — — — — — — — — — — — — 160S30(S2) 160S35(S2) — 160S40(S2) 160S45(S2) 160S54(S2) 160U60(U0) 160U70(U0) 160U80(U1) Page H-52 — — — — — — — — — — — — — — — — — — — — — — — 160J35 — 160M40 160M45 160M54 160M60 — — Page H-63 — — — — — — — — — — — — — — — — — — — — — — — 160TB35 160TB36 — 160TB45 — 160TB60 — — Page H-52 160A8 160A9 160A10 160A11 160A12 160A13 160A14 160A15 160A16 160A17 160A18 160A19 160A20 160A21 160A22 160A23 160A24 160A25 160A26 160A27 160A28 160A30 — 160A35 — 160A40 160A45 160A54 160A60 160A70 160A80 Page H-53 160B8 160B9 160B10 160B11 160B12 160B13 160B14 160B15 160B16 160B17 160B18 160B19 160B20 160B21 160B22 160B23 160B24 160B25 160B26 160B27 160B28 160B30 — 160C35 — 160C40 160C45 160C54 160C60 160C70 160C80 Page H-53 — — — — — — — — — — — — — — — — — — — — — — — D160M35 — — D160N45 — D160N60 — — Page H-53 — — — — — D160B13 D160B14 D160B15 D160B16 D160B17 D160B18 D160B19 D160B20 D160B21 D160B22 D160B23 — D160B25 D160B26 — — — — D160C35 — — D160C45 — D160C60 — — Stock Sprockets for No. 200 Single and Double Roller Chain Table No. 3 No. of Teeth 10 11 12 13 14 15 16 17 18 19 20 21 22 H-9 — — D140C45 — — D140C60 — — Stock Sprockets for No. 160 Single and Double Roller Chain Table No. 2 No of Teeth 140 & 200 Split Taper Bushing Type Page H-54 — — 200R12(R2) 200S13(S2) 200S14(S2) 200S15(S2) 200S16(S2) 200S17(S2) 200U18(U0) 200U19(U0) 200U20(U0) 200U21(U0) 200U22(U0) Q-D Bushing Type Page H-54 — — 200F12 200J13 200J14 200J15 200J16S 200M17 200M18 — — 200M21 — Type “A” Plate Minimum Bore Page H-55 200A10 200A11 200A12 200A13 200A14 200A15 200A16 200A17 200A18 200A19 200A20 200A21 200A22 Page H-55 200B10 200B11 200B12 200B13 200B14 200B15 200B16 200B17 200B18 200B19 200B20 200B21 200B22 Double Minimum Bore Page H-55 — D200B11 D200B12 D200B13 D200B14 D200B15 D200B16 D200B17 D200B18 D200B19 D200B20 D200B21 D200B22 No. of Teeth 23 24 25 26 28 30 32 35 40 45 54 60 — Split Taper Bushing Type Page H-54 200U23(U0) 200U24(U0) 200U25(U0) 200U26(U0) 200U28(U0) 200U30(U0) 200U32(U0) 200U35(U1) 200U40(U1) 200U45(U1) 200U54(U2) 200U60(U2) — Q-D Bushing Type Page H-54 — 200M24 200M25 200M26 200M28 — — 200M35 200M40 200N45 200N54 — — Type “A” Plate Minimum Bore Page H-55 200A23 200A24 200A25 200A26 200A28 200A30 200A32 200A35 200A40 200A45 200A54 200A60 — Page H-55 200B23 200B24 200B25 200C26 200C28 200C30 200C32 200C35 200C40 200C45 200C54 200C60 — Double Minimum Bore Page H-55 D200B23 D200B24 D200B25 D200B26 — — — — — D200C45 — D200C60 — Roller Chain Sprockets Sprockets for 25-35 No. 25 , 1/4" Pitch ANSI Chain Steel Type "B" Minimum Bore Sprockets Table No. 1 DIAMETERS Part No. Outside Pitch No. Teeth Type 25B9 25B10 25B11 25B12 .84” .92 .99 1.08 .731” .809 .887 .966 9 10 11 12 25B13 25B14 25B15 25B16 25B17 1.17 1.24 1.33 1.41 1.49 1.045 1.124 1.203 1.282 1.361 25B18 25B19 25B20 25B21 25B22 1.57 1.65 1.73 1.81 1.89 25B23 25B24 25B25 25B26 25B28 Bore DIMENSIONS L Max. 1/2” 1/2 1/2 1/2 P H Wt. Lbs 1/4” 1/4 5/16 3/8 T Nom. .110” .110 .110 .110 25/64” 25/64 25/64 25/64 7/16” 1/2 9/16 5/8 .03 .05 .05 .06 1/4 1/4 1/4 1/4 1/4 7/16 9/16 9/16 9/16 5/8 .110 .110 .110 .110 .110 1/2 1/2 1/2 1/2 1/2 25/64 25/64 25/64 25/64 25/64 23/32 13/16 57/64 31/32 1 1/32 .06 .08 .10 .11 .13 B B B B B 1/4 1/4 1/4 1/4 1/4 3/4 13/16 7/8 7/8 15/16 .110 .110 .110 .110 .110 1/2 1/2 5/8 5/8 5/8 25/64 25/64 33/64 33/64 33/64 1 1/8 1 7/32 1 9/32 1 3/8 1 7/16 .15 .18 .24 .28 .30 23 24 25 26 28 B B B B B 1/4 3/8 3/8 3/8 3/8 1 1 1 1 1 .110 .110 .110 .110 .110 5/8 5/8 5/8 5/8 5/8 33/64 33/64 33/64 33/64 33/64 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 .33 .33 .34 .34 .36 2.392 2.551 2.869 3.187 3.584 30 32 36 40 45 B B B B B 3/8 3/8 3/8 1/2 1/2 1 1 1 1 3/8 1 3/8 .110 .110 .110 .110 .110 5/8 5/8 5/8 3/4 3/4 33/64 33/64 33/64 41/64 41/64 1 1/2 1 1/2 1 1/2 2 2 .38 .40 .44 .78 .84 3.823 4.300 4.777 5.572 5.732 48 54 60 70 72 B B B B B 1/2 1/2 1/2 1/2 1/2 1 3/8 1 3/8 1 3/8 1 3/8 1 3/8 .110 .110 .110 .110 .110 3/4 3/4 3/4 3/4 3/4 41/64 41/64 41/64 41/64 41/64 2 2 2 2 2 .89 1.29 1.51 1.91 2.00 Stock Max. * B B B B 1/4” 1/4 1/4 1/4 13 14 15 16 17 B B B B B 1.440 1.519 1.598 1.678 1.757 18 19 20 21 22 1.97 2.05 2.13 2.21 2.37 1.836 1.915 1.995 2.074 2.233 25B30 25B32 25B36 25B40 25B45 2.53 2.69 3.01 3.33 3.73 25B48 25B54 25B60 25B70 25B72 3.96 4.44 4.92 5.72 5.88 *Maximum bore shown will accommodate standard keyway and setscrews over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. Type "B" Sprockets are made with minimum bore, no keyseat and no setscrew. They can be bored to size with keyseat and setscrew for a reasonable extra charge. Sprockets for No. 35 , 3/8" Pitch ANSI Chain Steel Single Sprockets with Browning Split Taper® Bushings Table No. 2 DIAMETERS Part No. Bushing Bore Range 35G15 35G16 35G17 35G18 35G19 G G G G G 3/8-1” 3/8-1” 3/8-1 3/8-1 3/8-1 Outside 1.99” 2.10 2.23 2.35 2.47 Pitch 1.804” 1.922 2.041 2.159 2.278 35H19 35H20 35H21 35H22 35H23 H H H H H 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 2.47 2.59 2.70 2.83 2.95 35H24 35H25 35H26 35H28 35H30 H H H H H 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 35H32 35H35 35H36 35H40 35H42 H H H H H 35H45 35H48 35H54 35H60 35H70 35H72 35H80 35H84 35H96 35H112 No. Type Teeth DIMENSIONS Wt. Less Bushing .3 .3 .3 .3 .3 15 16 17 18 19 .3 .3 .3 .3 .3 T Nom. .168" .168 .168 .168 .168 2.278 2.397 2.516 2.635 2.754 19 20 21 22 23 .3 .3 .3 .3 .3 .168 .168 .168 .168 .168 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/4 1 1/4 1 1/4 1 1/4 1 1/4 1 5/32 1 5/32 1 5/32 1 5/32 1 5/32 1/16 1/16 1/16 1/16 1/16 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 .5 .5 .6 .7 .7 3.05 3.19 3.31 3.55 3.79 2.873 2.992 3.111 3.349 3.588 24 25 26 28 30 .3 .3 .3 .3 .3 .168 .168 .168 .168 .168 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/4 1 1/4 1 1/4 1 1/4 1 1/4 1 5/32 1 5/32 1 5/32 1 5/32 1 5/32 1/16 1/16 1/16 1/16 1/16 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 .8 .8 .8 .9 .9 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 4.03 4.39 4.51 4.99 5.23 3.826 4.183 4.303 4.780 5.018 32 35 36 40 42 .3 .3 .3 .3 .3 .168 .168 .168 .168 .168 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/4 1 1/4 1 1/4 1 1/4 1 1/4 1 5/32 1 5/32 1 5/32 1 5/32 1 5/32 1/16 1/16 1/16 1/16 1/16 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 .9 1.0 1.0 1.2 1.2 H H H H H 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 5.59 5.95 6.66 7.38 8.58 5.379 5.734 6.449 7.165 8.358 45 48 54 60 70 .3 .3 .3 .3 .3 .168 .168 .168 .168 .168 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/4 1 1/4 1 1/4 1 1/4 1 1/4 1 5/32 1 5/32 1 5/32 1 5/32 1 5/32 1/16 1/16 1/16 1/16 1/16 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1.4 1.5 1.8 2.3 2.8 H H H H H 3/8-1 1/2 8.81 3/8-1 1/2 9.77 3/8-1 1/2 10.25 3/8-1 1/2 11.68 3/8-1 1/2 13.59 8.597 9.552 10.029 11.461 13.371 72 80 84 96 112 .3 .3 .3 .3 .3 .168 .168 .168 .168 .168 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/4 1 1/4 1 1/4 1 1/4 1 1/4 1 5/32 1 5/32 1 5/32 1 5/32 1 5/32 1/16 1/16 1/16 1/16 1/16 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 3.0 3.8 4.0 5.3 6.8 OL 1 11/32” 1 11/32 1 11/32 1 11/32 1 1/4 L 1” 1 1 1 1 P 1” 1 1 1 29/32 C 5/32” 5/32 5/32 5/32 1/16 H 2’ 2 2 2 2 Standard Keyseats Table No. 3 Bore Range Keyseat 3/8” - 7/16” 1/2 - 9/16 5/8 - 7/8 15/16 - 1 1/4 1 5/16 - 1 3/8 17/16 - 1 3/4 None 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-10 25-35 Roller Chain Sprockets Steel Sprockets with Q-D® Bushings Table No. 1 DIAMETERS DIMENSIONS T Nom. OL L P H Wt. Less Bushing 19 20 21 22 23 .168" .168 .168 .168 .168 1 5/16” 1 5/16 1 5/16 1 5/16 1 5/16 1” 1 1 1 1 63/64” 63/64 63/64 63/64 63/64 2” 2 2 2 2 .28 .37 .41 .43 .45 QD-1 QD-1 QD-1 QD-1 QD-1 24 25 26 27 28 .168 .168 .168 .168 .168 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 1 1 1 1 1 63/64 63/64 63/64 63/64 63/64 2 2 2 2 2 .48 .50 .53 .55 .58 3.588 3.826 4.183 4.303 4.780 QD-1 QD-1 QD-1 QD-1 QD-1 30 32 35 36 40 .168 .168 .168 .168 .168 1 5/16 1 1 5/16 1 1 5/16 1 1 23/32 1 5/16 1 23/32 1 5/16 63/64 2 63/64 2 63/64 2 1 21/64 2 11/16 1 21/64 2 11/16 .64 .71 .81 1.34 1.48 5.23 5.59 5.95 6.66 7.38 5.018 5.376 5.734 6.449 7.165 QD-1 QD-1 QD-1 QD-1 QD-1 42 45 48 54 60 .168 .168 .168 .168 .168 1 23/32 1 23/32 1 23/32 1 23/32 1 23/32 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 1 21/64 1 21/64 1 21/64 1 21/64 1 21/64 2 11/16 2 11/16 2 11/16 2 11/16 2 11/16 1.56 1.69 1.82 2.11 2.44 1/2-1 5/8 8.58 1/2-1 5/8 8.81 1/2-1 5/8 9.77 1/2-1 5/8 10.25 1/2-1 5/8 11.68 1/2-1 5/8 13.59 8.358 8.597 9.552 10.029 11.461 13.371 QD-1 QD-1 QD-1 QD-1 QD-1 QD-1 70 72 80 84 96 112 .168 .168 .168 .168 .168 .168 1 23/32 1 23/32 1 23/32 1 23/32 1 23/32 1 23/32 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 1 21/64 1 21/64 1 21/64 1 21/64 1 21/64 1 21/64 2 11/16 2 11/16 2 11/16 2 11/16 2 11/16 2 11/16 3.06 3.20 3.78 4.09 5.1 6.7 Part No. Bushing Bore Range Type No. Teeth Outside Pitch 35JA19* 35JA20 35JA21 35JA22 35JA23 JA JA JA JA JA 1/2-1 1/4” 1/2-1 1/4 1/2-1 1/4 1/2-1 1/4 1/2-1 1/4 2.47” 2.59 2.71 2.83 2.95 2.278” 2.397 2.516 2.635 2.745 QD-1 QD-1 QD-1 QD-1 QD-1 35JA24 35JA25 35JA26 35JA27 35JA28 JA JA JA JA JA 1/2-1 1/4 1/2-1 1/4 1/2-1 1/4 1/2-1 1/4 1/2-1 1/4 3.07 3.19 3.31 3.43 3.55 2.873 2.992 3.111 3.230 3.349 35JA30 35JA32 35JA35 35SH36 35SH40 JA JA JA SH SH 1/2-1 1/4 1/2-1 1/4 1/2-1 1/4 1/2-1 5/8 1/2-1 5/8 3.79 4.03 4.39 4.51 4.99 35SH42 35SH45 35SH48 35SH54 35SH60 SH SH SH SH SH 1/2-1 5/8 1/2-1 5/8 1/2-1 5/8 1/2-1 5/8 1/2-1 5/8 35SH70 35SH72 35SH80 35SH84 35SH96 35SH112 SH SH SH SH SH SH *Bushing mounts with capscrew heads on "A" side only. Finished Bore Single Sprockets Table No. 2 Part No. DIAMETERS Outside Pitch STOCK BORES MARKED “X” No. Type Teeth 3/8” 1/2” 5/8” 3/4” 7/8” 1” 1 1/8” 1 3/16” 1 1/4” Hardened Teeth STOCK Steel Sprockets H359 H3510 H3511 H3512 H3513 H3514 H3515 H3516 H3517 H3518 H3519 H3520 H3521 H3522 H3523 H3524 H3525 H3526 H3528 H3530 3532 3536 3540 3542 3545 3548 3560 1.25” 1.37 1.50 1.62 1.75 1.87 1.99 2.10 2.23 2.35 2.47 2.59 2.70 2.83 2.95 3.07 3.19 3.31 3.55 3.79 4.03 4.51 4.99 5.23 5.59 5.95 7.38 1.069” 1.214 1.331 1.449 1.567 1.685 1.804 1.922 2.041 2.159 2.278 2.397 2.516 2.635 2.754 2.873 2.992 3.111 3.349 3.588 3.862 4.303 4.780 5.018 5.376 5.734 7.165 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 28 30 32 36 40 42 45 48 60 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 x x x - x x x x x x x x x x x x x x x x - x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x - x x x x x x x x x x x x x x x x x x x x x x - x x x - x x x x DIMENSIONS T L Nom. Max. .168” .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 .168 3/4” 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 27/32 27/32 27/32 27/32 27/32 27/32 27/32 27/32 27/32 27/32 27/32 27/32 27/32 27/32 27/32 P Wt. Lbs. 37/64 37/64 37/64 37/64 37/64 37/64 37/64 37/64 37/64 37/64 37/64 37/64 43/64 43/64 43/64 43/64 43/64 43/64 43/64 43/64 43/64 43/64 43/64 43/64 43/64 43/64 43/64 .1 .1 .2 .2 .3 .3 .3 .4 .4 .5 .5 .7 .8 .8 .9 1.1 1.2 1.3 1.3 1.4 1.5 1.8 2.0 2.2 2.4 2.6 3.4 All Stock Finished Bore Sprockets are furnished with Standard Keyway on Centerline of Tooth and Hollow Head Setscrew over Keyway, except 1/2" bores and smaller which have setcrews only. Sprockets with HARDENED TEETH have an additional Setscrew at 90° to Keyway. H-11 Roller Chain Sprockets Sprockets for No. 35 , 3/8" Pitch ANSI Chain Type "A" Steel Plate Sprockets Table No. 1 Part Outside Pitch No. Dia. Dia. 35A15 1.99” 1.804” 35A16 2.11 1.922 35A17 2.23 2.041 35A18 2.35 2.159 35A19 2.47 2.278 No. Teeth 15 16 17 18 19 Stock Bore 1/2” 1/2 1/2 1/2 1/2 T (Nom.) .168 .168 .168 .168 .168 Wt Lbs. .12 .16 .18 .20 .22 Part Outside Pitch No. No. Dia Dia. Teeth 35A32 4.03” 3.826” 32 35A35 4.39 4.183 35 35A36 4.51 4.303 36 35A40 4.99 4.780 40 35A42 5.23 5.018 42 Stock Bore 1/2” 1/2 5/8 5/8 5/8 T (Nom.) .168 .168 .168 .168 .168 Wt. Lbs. .54 .64 .69 .84 .93 35A20 35A21 35A22 35A23 35A24 2.59 2.71 2.83 2.95 3.07 2.397 2.516 2.635 2.754 2.873 20 21 22 23 24 1/2 1/2 1/2 1/2 1/2 .168 .168 .168 .168 .168 .24 .26 .29 .30 .34 35A45 35A48 35A54 35A60 35A70 5.59 5.95 6.66 7.38 8.58 5.376 5.734 6.449 7.165 8.358 45 48 54 60 70 5/8 5/8 5/8 5/8 5/8 .168 .168 .168 .168 .168 1.06 1.20 1.50 1.90 2.60 35A25 35A26 35A27 35A28 35A30 3.19 3.31 3.43 3.55 3.79 2.992 3.111 3.230 3.349 3.588 25 26 27 28 30 1/2 1/2 1/2 1/2 1/2 .168 .168 .168 .168 .168 .37 .40 .43 .46 .53 35A72 8.81 35A80 9.77 35A84 10.25 35A96 11.68 35A112 13.59 8.597 9.552 10.029 11.461 13.371 72 80 84 96 112 5/8 5/8 5/8 5/8 5/8 .168 .168 .168 .168 .168 2.75 3.40 3.70 4.90 6.70 DIMENSIONS L P 3/4” 37/64" 3/4 37/64 3/4 37/64 3/4 37/64 3/4 37/64 H 3/4”† 55/64† 1 1/32† 1 5/32† 1 9/32† Wt. Lbs. .1 .1 .1 .1 .1 Steel Type "B" Minimum Bore Single Sprockets Table No. 2 Part No. 35B8 35B9 35B10 35B11 35B12 35 DIAMETERS Outside Pitch 1.12” .980” 1.25 1.096 1.37 1.214 1.50 1.331 1.62 1.449 No. Teeth 8 9 10 11 12 Type B B B B B BORE Stock Max.* 3/8” 3/8” 3/8 3/8 3/8 5/8 3/8 3/4 1/2 3/4 T Nom. .168” .168 .168 .168 .168 35B13 35B14 35B15 35B16 35B17 1.75 1.87 1.99 2.10 2.23 1.567 1.685 1.804 1.922 2.041 13 14 15 16 17 B B B B B 1/2 1/2 1/2 1/2 1/2 3/4 7/8 7/8 15/16 1 1/16 .168 .168 .168 .168 .168 3/4 3/4 3/4 3/4 3/4 37/64 37/64 37/64 37/64 37/64 1 25/64† 1 49/64† 1 37/64† 1 3/4† 1 3/4† .3 .3 .3 .4 .4 35B18 35B19 35B20 35B21 35B22 2.35 2.47 2.59 2.70 2.83 2.159 2.278 2.397 2.516 2.635 18 19 20 21 22 B B B B B 1/2 1/2 1/2 1/2 1/2 1 3/16 1 1/4 1 5/16 1 1/4 1 3/8 .168 .168 .168 .168 .168 3/4 3/4 3/4 27/32 27/32 37/64 37/64 37/64 43/64 43/64 1 3/4 1 27/32 1 15/16 2 1/16 2 3/16 .5 .6 .7 .8 .9 35B23 35B24 35B25 35B26 35B27 2.95 3.05 3.19 3.31 3.43 2.754 2.873 2.992 3.111 3.230 23 24 25 26 27 B B B B B 1/2 1/2 1/2 1/2 1/2 1 3/8 1 9/16 1 5/8 1 5/8 1 5/8 .168 .168 .168 .168 .168 27/32 27/32 27/32 27/32 27/32 43/64 43/64 43/64 43/64 43/64 2 3/16 2 7/16 2 1/2 2 1/2 2 1/2 1.0 1.2 1.3 1.3 1.3 35B28 35B30 35B32 35B35 35B36 3.55 3.79 4.03 4.39 4.51 3.349 3.588 3.826 4.183 4.303 28 30 32 35 36 B B B B B 1/2 1/2 1/2 1/2 5/8 1 5/8 1 5/8 1 5/8 1 5/8 1 5/8 .168 .168 .168 .168 .168 27/32 27/32 27/32 27/32 27/32 43/64 43/64 43/64 43/64 43/64 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1.3 1.4 1.5 1.5 1.5 35B40 35B42 35B45 35B48 35B54 35B60 4.99 5.23 5.59 5.95 6.66 7.38 4.780 5.018 5.376 5.734 6.449 7.165 40 42 45 48 54 60 B B B B B B 5/8 5/8 5/8 5/8 5/8 5/8 1 5/8 2 2 2 2 2 .168 .168 .168 .168 .168 .168 27/32 27/32 27/32 27/32 27/32 27/32 43/64 43/64 43/64 43/64 43/64 43/64 2 1/2 3 3 3 3 3 1.9 2.3 2.5 2.9 3.3 3.7 35B70 35B72 35B80 35B84 35B96 35B112 8.58 8.81 9.77 10.25 11.68 13.59 8.358 8.597 9.552 10.029 11.461 13.371 70 72 80 84 96 112 B B B B B B 5/8 5/8 5/8 5/8 5/8 5/8 2 2 2 2 2 2 .168 .168 .168 .168 .168 .168 27/32 27/32 27/32 27/32 27/32 27/32 43/64 43/64 43/64 43/64 43/64 43/64 3 3 3 3 3 3 4.7 4.9 5.8 6.2 7.7 10.1 *Maximum bore shown is with standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. †Hub is recessed for chain clearance. Type "B" Sprockets are made without keyways and setscrews. They are furnished with minimum bore which can be rebored to size, keywayed and setscrewed for a reasonable extra charge. Steel Double Sprockets with Q-D® Bushings Table No. 3 Part No. Bushing D35SDS68 D35SDS72 D35SDS76 SDS SDS SDS D35SK84 SK Wt. DIAMETERS DIMENSIONS Bore No. Type Less Range Outside Pitch Teeth T M OL L P C H Bushing 1/2-2” 8.34” 8.120” QD-4 68 .162” .561” 1 21/32” 1 5/16” 11/16” 3/16” 3 1/8” 7.5 1/2-2 8.81 8.597 QD-4 72 .162 .561 1 21/32 1 5/16 11/16 3/16 3 1/8 8.5 1/2-2 9.29 9.074 QD-4 76 .162 .561 1 21/32 1 5/16 11/16 3/16 3 1/8 9.5 1/2-2 5/8 10.25 10.029 QD-4 84 .162 .561 2 11/32 1 15/16 13/16 11/16 3 7/8 12.4 H-12 35-41 Roller Chain Sprockets Steel Double Type "B" Minimum Bore Sprockets HARDENED TEETH Table No. 1 Part No. DIAMETERS D35B12 D35B13 D35B14 D35B15 D35B16 Outside 1.63” 1.75 1.87 1.99 2.10 Pitch 1.449” 1.567 1.685 1.804 1.922 D35B17 D35B18 D35B19 D35B20 D35B21 2.23 2.35 2.47 2.59 2.70 2.041 2.159 2.278 2.397 2.516 D35B22 D35B23 D35B24 D35B25 D35B26 2.83 2.95 3.05 3.19 3.31 D35B30 D35B36 D35B42 D35B48 D35B52 D35B60 D35B68 D35B72 D35B76 D35B84 No. Teeth Type 12 13 14 15 16 BORE DIMENSIONS L P Max. 1 1/4” 11/16” 1 1/4 11/16 1 1/4 11/16 1 1/4 11/16 1 1/4 11/16 H 1 9/32† 1 25/64† 1 49/64† 1 37/64† 1 11/16† Wt. Lbs. DB DB DB DB DB Stock 1/2” 1/2 1/2 1/2 1/2 Max.* 9/16” 13/16 7/8 15/16 15/16 T .162” .162 .162 .162 .162 M .561” .561 .561 .561 .561 17 18 19 20 21 DB DB DB DB DB 1/2 1/2 1/2 1/2 1/2 1 1/16 1 3/16 1 5/16 1 5/16 1 3/8 .162 .162 .162 .162 .162 .561 .561 .561 .561 .561 1 1/4 1 1/4 1 1/4 1 3/8 1 3/8 11/16 11/16 11/16 13/16 13/16 1 3/4† 1 3/4 1 7/8 1 15/16 2 1/16 .8 .8 1.0 1.1 1.4 2.635 2.745 2.873 2.992 3.111 22 23 24 25 26 DB DB DB DB DB 1/2 1/2 1/2 1/2 1/2 1 7/16 1 1/2 1 5/8 1 3/4 1 3/4 .162 .162 .162 .162 .162 .561 .561 .561 .561 .561 1 3/8 1 3/8 1 3/8 1 3/8 1 3/8 13/16 13/16 13/16 13/16 13/16 2 3/16 2 5/16 2 7/16 2 1/2 2 1/2 1.5 1.6 1.9 2.1 2.2 3.79 4.51 5.23 5.95 6.43 3.588 4.303 5.018 5.374 6.211 30 36 42 48 52 DB DB DB DB DB 1/2 1/2 1/2 3/4 3/4 2 2 2 2 2 .162 .162 .162 .162 .162 .561 .561 .561 .561 .561 1 3/8 1 3/8 1 3/8 1 3/8 1 3/8 13/16 13/16 13/16 13/16 13/16 3 3 3 3 3 3.0 3.6 4.5 5.4 6.1 7.38 8.34 8.81 9.29 10.25 7.165 8.120 8.597 9.074 10.029 60 68 72 76 84 DB DB DB DB DB 3/4 3/4 1 1 1 2 2 3/8 2 3/8 2 3/8 2 1/2 .162 .162 .162 .162 .162 .561 .561 .561 .561 .561 1 3/8 1 1/2 1 1/2 1 1/2 1 1/2 13/16 15/16 15/16 15/16 15/16 3 3 1/2 3 1/2 3 1/2 3 3/4 7.8 10.4 11.2 12.2 14.9 .4 .4 .6 .6 .6 *Maximum bore shown is with standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. †Hub is recessed for chain clearance. These type "B" Sprockets are made without keyways and setscrews. They are furnished with minimum bore which can be rebored to size and keywayed for a reasonable extra charge. Sprockets for Standard Keyseats Bore Range Keyseat 3/8” - 7/16” 1/2 - 9/16 5/8 - 7/8 15/16 - 1 1/4 1 5/16 - 1 3/8 1 7/16 - 1 3/4 1 13/16 - 2 1/4 2 5/16 - 2 3/4 None 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-13 , 1/2" Pitch ANSI Chain Steel Single Sprockets with Browning Split Taper® Bushings Table No. 2 Table No. 3 No. 41 12 14 15 16 17 T Nom. .227” .227 .227 .227 .227 OL 1 7/16” 1 7/16 1 1/2 1 1/2 1 1/2 L 1” 1 1 1/4 1 1/4 1 1/4 P 1 1/32” 1 1/32 1 1/32 1 1/32 1 1/32 H 2” 2 2 1/2 2 1/2 2 1/2 Wt. Less Bushing .3 .4 .5 .5 .6 3 3 3 3 3 18 19 20 21 22 .227 .227 .227 .227 .227 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/4 1 1/4 1 1/4 1 1/4 1 1/4 1 1/32 1 1/32 1 1/32 1 1/32 1 1/32 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 .7 .8 .8 .9 .9 3.672 3.831 3.989 4.158 4.307 3 3 3 3 3 23 24 25 26 27 .227 .227 .227 .227 .227 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/4 1 1/4 1 1/4 1 1/4 1 1/4 1 1/32 1 1/32 1 1/32 1 1/32 1 1/32 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1.0 1.1 1.1 1.1 1.1 4.70 5.06 5.38 5.86 6.02 4.466 4.783 5.101 5.578 5.737 3 3 3 3 4 28 30 32 35 36 .227 .227 .227 .227 .227 1 1/2 1 1/2 1 1/2 1 1/2 2 3/16 1 1/4 1 1/32 1 1/4 1 1/32 1 1/4 1 1/32 1 1/4 1 1/32 1 15/16 1 19/32 2 1/2 2 1/2 2 1/2 2 1/2 3 1.2 1.3 1.5 1.8 2.5 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 6.55 6.97 7.45 7.93 8.89 9.84 6.373 6.691 7.168 7.645 8.599 9.554 4 4 4 4 4 4 40 42 45 48 54 60 .227 .227 .227 .227 .227 .227 2 3/16 2 3/16 2 3/16 2 3/16 2 3/16 2 3/16 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 1 19/32 1 19/32 1 19/32 1 19/32 1 19/32 1 19/32 3 3 3 3 3 3 3.0 3.1 3.5 4.0 4.6 5.5 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 11.43 11.75 13.03 13.66 15.57 18.12 11.145 11.463 12.736 13.372 15.281 17.828 4 4 4 4 4 4 70 72 80 84 96 112 .227 .227 .227 .227 .227 .227 2 3/16 2 3/16 2 3/16 2 3/16 2 3/16 2 3/16 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 1 19/32 1 19/32 1 19/32 1 19/32 1 19/32 1 19/32 3 3 3 3 3 3 7.0 7.9 9.3 9.7 13.0 18.0 DIAMETERS Part No. Bushing Bore Range Type No. Teeth 41G12 41G14 41H15 41H16 41H17 G G H H H 3/8-1” 3/8-1 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 Outside 2.17” 2.49 2.65 2.80 2.96 Pitch 1.932” 2.247 2.405 2.653 2.721 3 3 3 3 3 41H18 41H19 41H20 41H21 41H22 H H H H H 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 3.14 3.30 3.45 3.62 3.75 2.879 3.038 3.196 3.355 3.513 41H23 41H24 41H25 41H26 41H27 H H H H H 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 3.94 4.10 4.26 4.42 4.58 41H28 41H30 41H32 41H35 41P36 H H H H P1 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 3/8-1 1/2 1/2-1 3/4 41P40 41P42 41P45 41P48 41P54 41P60 P1 P1 P1 P1 P1 P1 41P70 41P72 41P80 41P84 41P96 41P112 P1 P1 P1 P1 P1 P1 DIMENSIONS Roller Chain Sprockets Sprockets for No. 41 , 1/2" Pitch ANSI Chain Steel Single Sprockets with Q-D® Bushings Table No. 1 15 16 17 18 19 T Nom. .227 .227 .227 .227 .227 OL 1 5/16” 1 5/16 1 5/16 1 5/16 1 5/16 L 1” 1 1 1 1 P 59/64” 59/64 59/64 59/64 59/64 H 2” 2 2 2 2 Wt. Less Bushing .32 .34 .49 .53 .58 QD-1 QD-1 QD-1 QD-1 QD-1 20 21 22 23 24 .227 .227 .227 .227 .227 1 23/32 1 23/32 1 23/32 1 23/32 1 23/32 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 1 17/64 1 17/64 1 17/64 1 17/64 1 17/64 2 11/16 2 11/16 2 11/16 2 11/16 2 11/16 .99 1.08 1.16 1.22 1.28 3.989 4.148 4.307 4.466 4.783 QD-1 QD-1 QD-1 QD-1 QD-1 25 26 27 28 30 .227 .227 .227 .227 .227 1 23/32 1 23/32 1 23/32 1 23/32 1 23/32 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 1 17/64 1 17/64 1 17/64 1 17/64 1 17/64 2 11/16 2 11/16 2 11/16 2 11/16 2 11/16 1.37 1.42 1.48 1.54 1.66 5.38 5.86 6.02 6.65 6.97 5.101 5.578 5.737 6.373 6.691 QD-1 QD-1 QD-1 QD-1 QD-1 32 35 36 40 42 .227 .227 .227 .227 .227 1 23/32 1 23/32 1 21/32 1 21/32 1 21/32 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 1 17/64 1 17/64 1 7/32 1 7/32 1 7/32 2 11/16 2 11/16 3 1/8 3 1/8 3 1/8 1.79 2.00 2.15 2.47 2.64 1/2-2 1/2-2 1/2-2 1/2-2 1/2-2 5/8 7.45 7.93 8.89 9.84 11.43 7.168 7.645 8.599 9.554 11.145 QD-1 QD-1 QD-1 QD-1 QD-1 45 48 54 60 70 .227 .227 .227 .227 .227 1 21/32 1 21/32 1 21/32 1 21/32 2 11/32 1 5/16 1 7/32 1 5/16 1 7/32 1 5/16 1 7/32 1 5/16 1 7/32 1 15/16 1 27/32 3 1/8 3 1/8 3 1/8 3 1/8 3 7/8 2.92 3.22 3.86 4.58 7.3 1/2-2 5/8 1/2-2 5/8 1/2-2 5/8 1/2-2 5/8 1/2-2 5/8 11.75 13.03 13.66 15.57 18.12 11.463 12.736 13.372 15.281 17.828 QD-1 QD-1 QD-1 QD-1 QD-1 72 80 84 96 112 .227 .227 .227 .227 .227 2 11/32 2 11/32 2 11/32 2 11/32 2 11/32 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 3 7/8 3 7/8 3 7/8 3 7/8 3 7/8 7.6 8.9 9.6 11.9 15.4 DIAMETERS Part No. Bushing Bore Range Pitch 2.405” 2.563 2.721 2.879 3.038 Type No. Teeth 41JA15 41JA16 41JA17 41JA18 41JA19 JA JA JA JA JA 1/2-1 1/4” 1/2-1 1/4 1/2-1 1/4 1/2-1 1/4 1/2-1 1/4 Outside 2.65” 2.81 2.98 3.14 3.30 QD-1 QD-1 QD-1 QD-1 QD-1 41SH20 41SH21 41SH22 41SH23 41SH24 SH SH SH SH SH 1/2-1 5/8 1/2-1 5/8 1/2-1 5/8 1/2-1 5/8 1/2-1 5/8 3.46 3.62 3.78 3.94 4.10 3.196 3.355 3.513 3.672 3.831 41SH25 41SH26 41SH27 41SH28 41SH30 SH SH SH SH SH 1/2-1 5/8 1/2-1 5/8 1/2-1 5/8 1/2-1 5/8 1/2-1 5/8 4.26 4.42 4.58 4.74 5.06 41SH32 41SH35 41SDS36 41SDS40 41SDS42 SH SH SDS SDS SDS 1/2-1 5/8 1/2-1 5/8 1/2-2 1/2-2 1/2-2 41SDS45 41SDS48 41SDS54 41SDS60 41SK70 SDS SDS SDS SDS SK 41SK72 41SK80 41SK84 41SK96 41SK112 SK SK SK SK SK DIMENSIONS 1 27/32 1 27/32 1 27/32 1 27/32 1 27/32 DIAMETERS 419 4110 4111 4112 4113 Outside 1.69” 1.84 2.00 2.17 2.30 Pitch 1.462” 1.618 1.775 1.932 2.089 4114 4115 4116 4117 4118 2.49 2.66 2.80 2.96 3.14 2.247 2.405 2.563 2.721 2.879 4119 4120 4121 4122 4124 3.30 3.45 3.62 3.78 4.10 4125 4130 4135 4136 4142 4154 4.26 5.06 5.86 6.02 6.97 8.89 No. Teeth Type 9 10 11 12 13 STOCK BORES MARKED "X" Standard Keyseats Table No. 3 Bore Range Keyseat 1/2" - 9/16" 5/8 - 7/8 15/16 - 1 1/4 1 5/16 - 1 3/8 1 7/16 - 1 3/4 1 13/16 - 2 1/4 2 5/16 - 2 3/4 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 1 3/8" B o r e B u sh in gs a l s o a v a i l ab le wit h 3/8" x 3/1 6 " K e y s e a t. Steel Finished Bore Single Sprockets Table No. 2 Part No. 41 DIMENSIONS T Nom. L Max. P .227” 7/8” 21/32” .227 7/8 21/32 .227 7/8 21/32 .227 7/8 21/32 .227 7/8 21/32 Wt. Lbs. 1 1 1 1 1 1/2” x x x x x 5/8” x x x x x 3/4” — x x x x 7/8” — — — x x 1” — — — — x 14 15 16 17 18 1 1 1 1 1 x x — — — x x x x x x x x x x x — — — — x x x x x .227 .227 .227 .227 .227 7/8 7/8 7/8 7/8 7/8 21/32 21/32 21/32 21/32 21/32 .6 .8 .8 1.0 1.1 3.038 3.196 3.335 3.513 3.831 19 20 21 22 24 1 1 1 1 1 — — — — — x x x x — x x x x — — — — — — x x x x x .227 .227 .227 .227 .227 7/8 7/8 7/8 7/8 7/8 21/32 21/32 21/32 21/32 21/32 1.2 1.4 1.5 1.6 1.8 3.984 4.783 5.578 5.737 6.691 8.599 25 30 35 36 42 54 1 1 1 1 1 1 — — — — — — — — — — — — x — — x x — — — — — — — x x x — — x .227 .227 .227 .227 .227 .227 7/8 7/8 7/8 7/8 7/8 7/8 21/32 21/32 21/32 21/32 21/32 21/32 2.0 2.3 2.7 2.8 3.4 4.8 .2 .3 .4 .4 .5 All Stocks Finished Bore Sprockes are furnished with Standard Keyway on Centerline of Tooth and Setscrew over Keyway, exept 1/2" bore which has no keyway. H-14 Roller Chain Sprockets 41 Type "A" Steel Plate Sprockets Table No. 1 Part No. Outside Dia. Pitch Dia No. Teeth Stock Bore T (Nom.) Wt. Lbs. Part No. Outside Dia. Pitch Dia No. Teeth Stock Bore T (Nom.) Wt. Lbs. 41A15 41A16 41A17 41A18 41A19 2.65” 2.80 2.96 3.14 3.30 2.405” 2.563 2.721 2.879 3.038 15 16 17 18 19 5/8” 5/8 5/8 5/8 5/8 .227” .227 .227 .227 .227 .3 .3 .3 .3 .3 41A32 41A35 41A36 41A40 41A42 5.38” 5.86 6.02 6.65 6.97 5.101” 5.578 5.737 6.373 6.691 32 35 36 40 42 5/8” 5/8 5/8 5/8 3/4 .227” .227 .227 .227 .227 1.2 1.5 1.5 1.9 2.3 41A20 41A21 41A22 41A23 41A24 3.45 3.62 3.75 3.94 4.10 3.196 3.355 3.513 3.672 3.831 20 21 22 23 24 5/8 5/8 5/8 5/8 5/8 .227 .227 .227 .227 .227 .4 .4 .5 .6 .6 41A45 41A48 41A54 41A60 41A70 7.45 7.93 8.89 9.84 11.43 7.168 7.645 8.599 9.554 11.145 45 48 54 60 70 3/4 3/4 3/4 3/4 3/4 .227 .227 .227 .227 .227 2.6 3.0 3.6 4.5 6.5 41A25 41A26 41A27 41A28 41A30 4.26 4.42 4.58 4.70 5.06 3.989 4.148 4.307 4.466 4.783 25 26 27 28 30 5/8 5/8 5/8 5/8 5/8 .227 .227 .227 .227 .227 .6 .7 .8 .8 1.1 41A72 41A80 41A84 41A96 41A112 11.75 13.03 13.66 15.57 18.12 11.463 12.736 13.372 15.281 17.828 72 80 84 96 112 3/4 3/4 3/4 3/4 3/4 .227 .227 .227 .227 .227 6.5 8.4 9.9 11.5 15.9 Steel Single Type "B" Minimum Bore Sprockets Table No. 2 Part No. DIAMETERS No. Teeth Type 6 7 8 9 10 BORE DIMENSIONS L P Max. 7/8” 21/32” 7/8 21/32 7/8 21/32 7/8 21/32 7/8 21/32 Wt. Lbs. B B B B B Stock 3/8” 3/8 1/2 1/2 1/2 Max.* 3/8” 3/8 1/2 5/8 3/4 T Nom. .227” .227 .227 .227 .227 11 12 13 14 15 B B B B B 1/2 1/2 1/2 1/2 1/2 7/8 15/16 1 1 1/4 1 5/16 .227 .227 .227 .227 .227 7/8 7/8 7/8 7/8 7/8 21/32 21/32 21/32 21/32 21/32 1 7/16† 1 19/32† 1 3/4† 1 29/32† 2 1/16† .3 .4 .5 .6 .7 2.563 2.721 2.879 3.038 3.196 16 17 18 19 20 B B B B B 5/8 5/8 5/8 5/8 5/8 1 3/8 1 1/2 1 5/8 1 3/4 1 7/8 .227 .227 .227 .227 .227 7/8 7/8 7/8 7/8 7/8 21/32 21/32 21/32 21/32 23/32 2 1/16 2 15/64 2 3/8 2 1/2 2 3/4 .8 .9 1.1 1.2 1.4 3.62 3.75 3.94 4.10 4.26 3.355 3.513 3.672 3.831 3.989 21 22 23 24 25 B B B B B 5/8 5/8 5/8 5/8 5/8 1 7/8 2 2 1/4 2 1/4 2 1/4 .227 .227 .227 .227 .227 7/8 7/8 7/8 7/8 7/8 23/32 23/32 23/32 23/32 23/32 2 7/8 3 3 3/16 3 1/4 3 1/4 1.5 1.6 1.6 1.7 1.7 41B26 41B27 41B28 41B30 41B32 4.42 4.58 4.70 5.06 5.38 4.148 4.307 4.466 4.783 5.101 26 27 28 30 32 B B B B B 5/8 5/8 5/8 5/8 5/8 2 1/4 2 1/4 2 1/4 2 1/4 2 1/4 .227 .227 .227 .227 .227 7/8 7/8 7/8 7/8 7/8 23/32 23/32 23/32 23/32 23/32 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 1.7 1.8 1.8 2.0 2.6 41B35 41B36 41B40 41B42 41B45 5.86 6.02 6.65 6.97 7.45 5.307 5.737 6.373 6.691 7.168 35 36 40 42 45 B B B B B 5/8 5/8 5/8 5/8 5/8 2 1/4 2 1/4 2 1/4 2 3/8 2 3/8 .227 .227 .227 .227 .227 7/8 7/8 7/8 7/8 7/8 23/32 23/32 23/32 23/32 23/32 3 1/4 3 1/4 3 1/4 3 1/2 3 1/2 2.9 2.9 3.3 3.5 3.9 41B48 41B54 41B60 41B70 41B72 7.93 8.89 9.84 11.43 11.75 7.645 8.599 9.554 11.145 11.463 48 54 60 70 72 B B B B B 5/8 5/8 5/8 3/4 3/4 2 3/8 2 3/8 2 3/8 2 3/4 2 3/4 .227 .227 .227 .227 .227 7/8 7/8 7/8 15/16 15/16 23/32 23/32 23/32 25/32 25/32 3 1/2 3 1/2 3 1/2 4 4 4.3 5.2 6.2 7.8 8.1 41B80 41B84 41B96 41B112 13.03 13.66 15.57 18.12 12.736 13.372 15.281 17.828 84 84 96 112 B B B B 3/4 3/4 3/4 3/4 2 3/4 2 3/4 2 3/4 2 3/4 .227 .227 .227 .227 15/16 15/16 15/16 15/16 25/32 25/32 25/32 25/32 4 4 4 4 9.9 10.3 14.1 19.0 41B6 41B7 41B8 41B9 41B10 Outside 1.17” 1.34 1.50 1.67 1.84 Pitch 1.000” 1.152 1.307 1.462 1.618 41B11 41B12 41B13 41B14 41B15 2.00 2.17 2.30 2.49 2.65 1.775 1.932 2.089 2.247 2.405 41B16 41B17 41B18 41B19 41B20 2.80 2.96 3.14 3.30 3.45 41B21 41B22 41B23 41B24 41B25 H 43/64† 13/16† 63/64 1 1/8† 1 9/32† .1 .1 .1 .2 .3 *Maximum bore shown is with standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. †Hub is recessed for chain clearance. These Type "B" Sprockets are made without keyways and setscrews. They are furnished with minimum bore which can be rebored to size, keywayed and setscrewed for a reasonable extra charge. H-15 Roller Chain Sprockets Sprockets for No. 40 , 1/2" Pitch ANSI Chain Steel Single Sprockets with Browning Split Taper® Bushings Table No. 1 HARDENED TEETH 40 P 1 1/32” 1 1/32 1 1/32 1 1/8 25/32 C 5/16” 5/16 5/16 5/32 1/16 Wt. Less H Bushing 2” .3 2 .4 2 .5 2 1/2 .5 2 .4 1 19/32 1 1/4 1 1/2 1 1/4 1 1/2 1 1/4 2 3/16 1 15/16 1 1/4 1 1/4 1 1/8 1 1/32 1 1/32 1 21/32 1 1/32 5/32 1/16 1/16 0 1/16 2 1/2 2 1/2 2 1/2 3 2 1/2 .6 .6 .7 1.2 .8 .284 .284 .284 .284 .284 2 3/16 1 15/16 1 1/2 1 1/4 2 3/16 1 15/16 1 1/2 1 1/4 2 3/16 1 15/16 1 21/32 1 1/32 1 21/32 1 1/32 1 21/32 0 1/16 0 1/16 0 3 2 1/2 3 2 1/2 3 1.3 .8 1.3 9 1.5 3 4 3 4 3 .284 .284 .284 .284 .284 1 1/2 1 1/4 2 3/16 1 15/16 1 1/2 1 1/4 2 3/16 1 15/16 1 1/2 1 1/4 1 1/32 1 21/32 1 1/32 1 21/32 1 1/32 1/16 0 1/16 0 1/16 2 1/2 3 2 1/2 3 2 1/2 .9 .6 1.0 1.7 1.2 24 25 25 26 26 4 3 4 3 4 .284 .284 .284 .284 .284 2 3/16 1 15/16 1 1/2 1 1/4 2 3/16 1 15/16 1 1/2 1 1/4 2 3/16 1 15/16 1 21/32 1 1/32 1 21/32 1 1/32 1 21/32 0 1/16 0 1/16 0 3 2 1/2 3 2 1/2 3 1.8 1.3 2.0 1.4 2.0 4.307 4.307 4.466 4.466 4.625 27 27 28 28 29 3 4 3 4 4 .284 .284 .284 .284 .284 1 1/2 1 1/4 2 3/16 1 15/16 1 1/2 1 1/4 2 3/16 1 15/16 2 3/16 1 15/16 1 1/32 1 21/32 1 1/32 1 21/32 1 21/32 1/16 0 1/16 0 0 2 1/2 3 2 1/2 3 3 1.4 2.1 1.5 2.2 2.3 5.06 5.06 5.38 5.54 5.86 4.783 4.783 5.101 5.260 5.578 30 30 32 33 35 3 4 3 3 3 .284 .284 .284 .284 .284 1 1/2 1 1/4 2 3/16 1 15/16 1 1/2 1 1/4 1 1/2 1 1/4 1 1/2 1 1/4 1 1/32 1 21/32 1 1/32 1 1/32 1 1/32 1/16 0 1/16 1/16 1/16 2 1/2 3 2 1/2 2 1/2 2 1/2 1.6 2.4 1.8 1.9 2.1 6.02 6.33 6.65 5.22 5.38 5.54 5.737 36 3 .284 1 1/2 1 1/4 1 1/32 6.055 38 3 .284 1 1/2 1 1/4 1 1/32 6.373 40 3 .284 1 1/2 1 1/4 1 1/32 4.942 31 4 .284 2 3/16 1 15/16 1 21/32 5.101 32 4 .284 2 3/16 1 15/16 1 21/32 5.260 33 4 .284 2 3/16 1 15/16 1 21/32 LARGER SIZES ON NEXT PAGE 1/16 1/16 1/16 0 0 0 2 1/2 2 1/2 2 1/2 3 3 3 2.3 2.6 2.8 2.5 2.6 2.6 DIAMETERS Part No. Bushing Bore Range H40G12 H40G13 H40G14 H40H15 H40G16 G G G H G 3/8 - 1” 3/8 - 1 3/8 - 1 3/8 - 1 1/2 3/8 - 1 Outside 2.17” 2.30 2.49 2.65 2.80 Pitch 1.932” 2.089 2.247 2.405 2.563 H40H16 H40H17 H40H18 H40P18 H40H19 H H H P1 H 3/8 - 1 1/2 3/8 - 1 1/2 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 2.80 2.96 3.14 3.14 3.30 H40P19 H40H20 H40P20 H40H21 H40P21 P1 H P1 H P1 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 H40H22 H40P22 H40H23 H40P23 H40H24 H P1 H P1 H H40P24 H40H25 H40P25 H40H26 H40P26 No. Type Teeth DIMENSIONS T OL Norm. .284” 1 1/2” .284 1 1/2 .284 1 1/2 .284 1 19/32 .284 1 1/4 12 13 14 15 16 3 3 3 3 3 2.563 2.721 2.879 2.879 3.038 16 17 18 18 19 3 3 3 4 3 .284 .284 .284 .284 .284 3.30 3.45 3.45 3.62 3.62 3.038 3.196 3.196 3.355 3.355 19 20 20 21 21 4 3 4 3 4 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 3.75 3.75 3.94 3.94 4.10 3.513 3.513 3.672 3.672 3.831 22 22 23 23 24 P1 H P1 H P1 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 4.10 4.26 4.26 4.42 4.42 3.831 3.989 3.989 4.148 4.148 H40H27 H40P27 H40H28 H40P28 H40P29 H P1 H P1 P1 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 1/2 - 1 3/4 4.58 4.58 4.74 4.74 4.90 H40H30 H40P30 H40H32 H40H33 H40H35 H P1 H H H 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 3/8 - 1 1/2 3/8 - 1 1/2 H40H36 H40H38 H40H40 40P31 40P32 40P33 H H H P1 P1 P1 3/8 - 1 1/2 3/8 - 1 1/2 3/8 - 1 1/2 1/2 - 1 3/4 1/2 - 1 3/4 1/2 - 1 3/4 L 1” 1 1 1 1/4 1 Where two sprockets with the same number of teeth but different bushings are offered, we suggest using the sprocket bushing for heavier service drives. Standard Keyseats Table No. 3 Bore Range Keyseat 3/8” - 7/16” 1/2 - 9/16 5/8 - 7/8 15/16 - 1 1/4 1 5/16 - 1 3/8 1 7/16 - 1 3/4 None 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-16 40 Roller Chain Sprockets Steel Single Sprockets with Browning Split Taper® Bushings Table No. 1 Part No. Bushing DIAMETERS Bore Range Outside Pitch P C H Wt. Less Bushing 1 21/32” 1 21/32 1 21/32 1 21/32 1 21/32 0 0 0 0 0 3” 3 3 3 3 2.8 2.9 3.1 3.3 3.3 DIMENSIONS No. Type Teeth T Nom. OL L 40P34 40P35 40P36 40P37 40P38 P1 P1 P1 P1 P1 1/2-1 3/4” 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 SMALLER SIZES ON PRECEDING PAGE 5.70” 5.419” 34 4 .284” 2 3/16” 1 15/16” 5.86 5.578 35 4 .284 2 3/16 1 15/16 6.02 5.737 36 4 .284 2 3/16 1 15/16 6.18 5.896 37 4 .284 2 3/16 1 15/16 6.33 6.055 38 4 .284 2 3/16 1 15/16 40P40 40P41 40P42 40P44 40P45 P1 P1 P1 P1 P1 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 6.65 6.81 6.97 7.29 7.45 6.373 6.532 6.691 7.009 7.168 40 41 42 44 45 4 4 4 4 4 .284 .284 .284 .284 .284 2 3/16 2 3/16 2 3/16 2 3/16 2 3/16 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 1 21/32 1 21/32 1 21/32 1 21/32 1 21/32 0 0 0 0 0 3 3 3 3 3 3.5 3.6 3.9 4.0 4.2 40P47 40P48 40P50 40P54 40P56 P1 P1 P1 P1 P1 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 7.77 7.93 8.25 8.89 9.20 7.486 7.645 7.963 8.599 8.917 47 48 50 54 56 4 4 4 4 4 .284 .284 .284 .284 .284 2 3/16 2 3/16 2 3/16 2 3/16 2 3/16 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 1 21/32 1 21/32 1 21/32 1 21/32 1 21/32 0 0 0 0 0 3 3 3 3 3 4.6 4.8 5.0 5.5 5.9 40P60 40Q60 40P70 40Q70 40Q72 P1 Q1 P1 Q1 Q1 1/2-1 3/4 3/4-2 11/16 1/2-1 3/4 3/4-2 11/16 3/4-2 11/16 9.84 9.84 11.43 11.43 11.75 9.554 9.554 11.145 11.145 11.463 60 60 70 70 72 4 4 4 4 4 .284 .284 .284 .284 .284 2 3/16 1 15/16 1 21/32 2 25/32 2 1/2 2 7/32 2 3/16 1 15/16 1 21/32 2 25/32 2 1/2 2 7/32 2 25/32 2 1/2 2 7/32 0 0 0 0 0 3 4 1/8 3 4 1/8 4 1/8 6.6 8.8 8.6 11.0 11.2 40Q80 40Q84 40Q96 40Q112 Q1 Q1 Q1 Q1 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 13.03 13.66 15.57 18.12 12.736 13.372 15.281 17.828 80 84 96 112 4 4 4 4 .284 .284 .284 .284 2 25/32 2 25/32 2 25/32 2 25/32 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 13.1 14.1 17.3 12.8 2 1/2 2 1/2 2 1/2 2 1/2 2 7/32 2 7/32 2 7/32 2 7/32 Where two sprockets with the same number of teeth but different bushings are offered, we suggest using the sprocket bushing for heavier service drives. Steel Single Sprockets with Q-D® Bushings HARDENED TEETH Table No. 2 QD-1 QD-1 QD-1 QD-1 QD-1 T Norm. .284” .284 .284 .284 .284 OL 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 L 1 1 1 1 1 P 7/8 7/8 7/8 7/8 7/8 H 2 2 2 2 2 Wt. Less Bushing .34 .43 .53 .58 .64 20 21 22 23 24 QD-1 QD-1 QD-1 QD-1 QD-1 .284 .284 .284 .284 .284 1 23/32 1 23/32 1 23/32 1 23/32 1 23/32 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 1 7/32 1 7/32 1 7/32 1 7/32 1 7/32 2 11/16 2 11/16 2 11/16 2 11/16 2 11/16 .86 1.07 1.17 1.27 1.35 3.989 4.148 4.307 4.466 4.783 25 26 27 28 30 QD-1 QD-1 QD-1 QD-1 QD-1 .284 .284 .284 .284 .284 1 23/32 1 23/32 1 23/32 1 23/32 1 23/32 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 1 7/32 1 7/32 1 7/32 1 7/32 1 7/32 2 11/16 2 11/16 2 11/16 2 11/16 2 11/16 1.42 1.50 1.57 1.65 1.82 5.38 5.86 6.02 6.65 6.97 5.101 5.578 5.737 6.373 6.691 32 35 36 40 42 QD-1 QD-1 QD-1 QD-1 QD-1 .284 .284 .284 .284 .284 1 23/32 1 5/16 1 23/32 1 5/16 1 21/32 1 13/16 1 21/32 1 13/16 1 21/32 1 13/16 1 7/32 1 7/32 1 5/32 1 5/32 1 5/32 2 11/16 2 11/16 3 1/8 3 1/8 3 1/8 1.99 2.27 2.26 2.69 2.92 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 5/8 7.45 7.93 8.89 9.84 11.43 7.168 7.645 8.599 9.554 11.145 45 48 54 60 70 QD-1 QD-1 QD-1 QD-1 QD-1 .284 .284 .284 .284 .284 1 21/32 1 21/32 1 21/32 1 21/32 2 11/32 1 13/16 1 5/32 1 13/16 1 5/32 1 13/16 1 5/32 1 13/16 1 5/32 1 15/16 1 25/32 3 1/8 3 1/8 3 1/8 3 1/8 3 7/8 3.29 3.68 4.54 5.5 8.3 1/2 - 2 5/8 1/2 - 2 5/8 1/2 - 2 5/8 1/2 - 2 5/8 1/2 - 2 5/8 11.75 13.03 13.66 15.57 18.12 11.463 12.736 13.372 15.281 17.828 72 80 84 96 112 QD-1 QD-1 QD-1 QD-1 QD-1 .284 .284 .284 .284 .284 2 11/32 2 11/32 2 11/32 2 11/32 2 11/32 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 3 7/8 3 7/8 3 7/8 3 7/8 3 7/8 8.7 10.4 11.4 14.4 19.1 Part No. Bushing Bore Range H40JA15* H40JA16 H40JA17 H40JA18 H40JA19 JA JA JA JA JA H40SH20* H40SH21 H40SH22 H40SH23 H40SH24 DIAMETERS No. Teeth Type 15 16 17 18 19 3.196 3.355 3.513 3.672 3.831 4.26 4.42 4.58 4.74 5.06 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 2 1/2 - 2 1/2 - 2 SDS SDS SDS SDS SK SK SK SK SK SK 1/2 - 1 1/4 1/2 - 1 1/4 1/2 - 1 1/4 1/2 - 1 1/4 1/2 - 1 1/4 Outside 2.65 2.81 2.98 3.14 3.30 Pitch 2.405 2.563 2.721 2.879 3.038 SH SH SH SH SH 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 3.46 3.62 3.78 3.94 4.10 H40SH25 H40SH26 H40SH27 H40SH28 H40SH30 SH SH SH SH SH 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 40SH32 40SH35 40SDS36 40SDS40 40SDS42 SH SH SDS SDS SDS 40SDS45 40SDS48 40SDS54 40SDS60 40SK70 40SK72 40SK80 40SK84 40SK96 40SK112 * Bushings mounts with capscrews on “A” side only H-17 DIMENSIONS 1 25/32 1 25/32 1 25/32 1 25/32 1 25/32 Roller Chain Sprockets Sprockets for HARDENED TEETH No. 40 , 1/2" Pitch ANSI Chain Steel Finished Bore Single Sprockets Table No. 1 Part No. 40 DIAMETERS Outside Pitch STOCK Steel Sprockets H409 1.67” 1.462” H4010 1.84 1.618 H4011 2.00 1.775 H4012 2.17 1.932 H4013 2.30 2.089 H4014 2.49 2.247 H4015 2.65 2.405 H4016 2.80 2.563 H4017 2.96 2.721 H4018 3.14 2.879 H4019 3.30 3.038 H4020 3.45 3.196 H4021 3.62 3.355 H4022 3.75 3.513 H4023 3.94 3.672 H4024 4.10 3.831 H4025 4.26 3.989 H4026 4.42 4.148 H4027 4.58 4.307 H4028 4.74 4.466 H4029 4.90 4.625 H4030 5.06 4.783 4031 5.22 4.942 4032 5.38 5.101 4033 5.54 5.250 4034 5.70 5.419 4035 5.86 5.578 4036 6.02 5.737 4037 6.18 5.895 4038 6.33 6.055 4040 6.65 6.373 4042 6.97 6.691 4044 7.29 7.009 4045 7.45 7.168 4048 7.93 7.645 4051 8.41 8.122 4054 8.89 8.599 4056 9.20 8.917 4060 9.84 9.554 4080 13.03 12.736 No. Type Teeth 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 40 42 44 45 48 51 54 56 60 80 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 STOCK BORES MARKED “X” 1/2” 5/8” 3/4” 7/8” 1” x x x x x x x - x x x x x x x x x x x x x x x x x x x x x x - x x x x x x x x x x x x x x x x x x x x x x x x x x x x x - x x x x x x x x x x x x x x x x x x x x x x - x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x DIMENSIONS T L P 1 1/8” 1 3/16” 1 1/4” 1 3/8” 1 7/16” 1 1/2” 1 11/6” Nom. Max. x x x x x x x x x x x x x x x x x x x x x - x x x x x x x x x x x x x x x x x x - x x x x x x x x x x x x x x x x x x x x x x x x x x x - x x x x x x x x x - x x x x x x x x x x x x x x x x x x x - x x x x x x x x x x x x x x x x x x x x - x - .284” .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 .284 7/8” 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 15/16 Wt. Lbs. 19/32” .2 19/32 .3 19/32 .4 19/32 .4 19/32 .5 19/32 .6 19/32 .7 19/32 .8 19/32 .9 19/32 1.1 19/32 1.2 21/32 1.4 21/32 1.6 21/32 1.7 21/32 1.7 21/32 1.8 21/32 1.8 21/32 1.9 21/32 2.0 21/32 2.0 21/32 2.1 21/32 2.1 21/32 2.3 21/32 2.4 21/32 2.5 21/32 2.6 21/32 2.7 21/32 2.8 21/32 2.9 21/32 3.1 21/32 3.2 21/32 3.4 21/32 3.7 21/32 3.9 21/32 4.3 21/32 4.7 21/32 5.1 21/32 5.5 21/32 6.2 21/32 10.0 All Stocked Finished Bore Sprockets are furnished with Standard Keyway on Centerline of Tooth and Hollow Head Setscrew over Keyway, except 1/2" bores and smaller which have setscrews only. Stock Sprokets with HARDENED TEETH have additional Setscrew at 90° to Keyway. Type "A" Steel Plate Sprockets Table No. 2 Part No. Outside Dia. Pitch Dia. No. Teeth Stock T Bore (Nom.) Wt. Lbs. Part No. 40A12 40A13 40A14 40A15 40A16 2.17” 2.30 2.49 2.65 2.80 1.932” 2.089 2.247 2.405 2.563 12 13 14 15 16 1/2” 1/2 1/2 5/8 5/8 40A17 40A18 40A19 40A20 40A21 2.96 3.14 3.30 3.45 3.62 2.721 2.879 3.038 3.196 3.355 17 18 19 20 21 40A22 40A23 40A24 40A25 40A26 3.75 3.94 4.10 4.26 4.42 3.513 3.672 3.831 3.989 4.148 40A27 40A28 40A29 40A30 40A31 4.58 4.74 4.90 5.06 5.22 40A32 40A33 40A34 40A35 40A36 40A37 40A38 40A39 40A40 Outside Pitch Dia. Dia. No. Teeth Stock Bore T (Nom.) Wt. Lbs .284” .284 .284 .284 .284 .2 .2 .3 .3 .3 40A41 40A42 40A43 40A44 40A45 6.81” 6.97 7.13 7.29 7.45 6.532” 6.691 6.850 7.009 7.168 41 42 43 44 45 5/8 5/8 5/8 5/8 5/8 .284 .284 .284 .284 .284 2.3 2.5 2.6 2.7 2.8 5/8 5/8 5/8 5/8 5/8 .284 .284 .284 .284 .284 .3 .4 .4 .5 .5 40A46 40A47 40A48 40A49 40A50 7.61 7.77 7.93 8.09 8.25 7.327 7.486 7.645 7.804 7.963 46 47 48 49 50 5/8 5/8 5/8 5/8 5/8 .284 .284 .284 .284 .284 3.0 3.1 3.2 3.4 3.5 22 23 24 25 26 5/8 5/8 5/8 5/8 5/8 .284 .284 .284 .284 .284 .6 .7 .8 .8 .9 40A51 40A52 40A53 40A54 40A55 8.41 8.57 8.73 8.89 9.04 8.122 8.281 8.440 8.599 8.758 51 52 53 54 55 5/8 5/8 5/8 5/8 5/8 .284 .284 .284 .284 .284 3.6 3.8 3.9 4.1 4.2 4.307 4.466 4.625 4.783 4.942 27 28 29 30 31 5/8 5/8 5/8 5/8 5/8 .284 .284 .284 .284 .284 1.0 1.1 1.2 1.2 1.3 40A56 40A57 40A58 40A59 40A60 9.20 9.36 9.52 9.68 9.84 8.917 9.076 9.236 9.395 9.554 56 57 58 59 60 5/8 5/8 5/8 5/8 5/8 .284 .284 .284 .284 .284 4.4 4.6 4.7 4.9 5.1 5.38 5.54 5.70 5.86 6.02 5.101 5.260 5.419 5.578 5.737 32 33 34 35 36 5/8 5/8 5/8 5/8 5/8 .284 .284 .284 .284 .284 1.3 1.4 1.5 1.6 1.8 40A64 40A70 40A72 40A80 40A84 10.48 11.43 11.75 13.03 13.66 10.190 11.145 11.463 12.736 13.372 64 70 72 80 84 5/8 5/8 5/8 5/8 3/4 .284 .284 .284 .284 .284 6.3 7.8 8.3 10.2 11.3 6.18 6.33 6.49 6.55 5.896 6.055 6.214 6.373 37 38 39 40 5/8 5/8 5/8 5/8 .284 .284 .284 .284 1.9 2.0 2.1 2.2 40A96 40A102 40A112 40A120 15.57 16.53 18.12 19.39 15.281 16.236 17.828 19.101 96 102 112 120 3/4 3/4 3/4 3/4 .284 .284 .284 .284 14.7 16.6 20.0 23.0 H-18 Roller Chain Sprockets Steel Type "B" Minimum Bore Sprockets Table No. 1 Part No. Standard Keyseats Table No. 2 Bore Range Keyseat 3/8” - 7/16” 1/2 - 9/16 5/8 - 7/8 15/16 - 1 1/4 1 5/16 - 1 3/8 1 7/16 - 1 3/4 None 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-19 40 DIAMETERS No. Teeth Type 8 9 10 11 12 BORE DIMENSIONS Wt. Lbs. B B B B B Stock 1/2” 1/2 1/2 1/2 1/2 Max. * 1/2” 9/16 3/4 7/8 1 T Nom. .284” .284 .284 .284 .284 13 14 15 16 17 B B B B B 1/2 1/2 1/2 5/8 5/8 1 1/16 1 1/8 1 1/4 1 3/8 1 7/16 .284 .284 .284 .284 .284 7/8 7/8 7/8 7/8 7/8 19/32 19/32 19/32 19/32 19/32 1 3/4† 1 57/64† 2 1/16† 2 1/16 2 3/16 .5 .6 .7 .8 .9 2.879 3.038 3.196 3.355 3.513 18 19 20 21 22 B B B B B 5/8 5/8 5/8 5/8 5/8 1 1/2 1 3/4 1 7/8 1 7/8 1 7/8 .284 .284 .284 .284 .284 7/8 7/8 15/16 15/16 15/16 19/32 19/32 21/32 21/32 21/32 2 3/8 2 1/2 2 5/8 2 3/4 2 7/8 1.1 1.4 1.6 1.7 1.9 3.94 4.10 4.26 4.42 4.58 3.672 3.831 3.989 4.148 4.307 23 24 25 26 27 B B B B B 5/8 5/8 5/8 5/8 5/8 2 2 1/4 2 1/4 2 1/4 2 1/4 .284 .284 .284 .284 .284 15/16 15/16 15/16 15/16 15/16 21/32 21/32 21/32 21/32 21/32 3 3 1/4 3 1/4 3 1/4 3 1/4 2.1 2.4 2.5 2.5 2.6 40B28 40B29 40B30 40B31 40B32 4.74 4.90 5.06 5.22 5.38 4.466 4.625 4.783 4.942 5.101 28 29 30 31 32 B B B B B 5/8 5/8 5/8 5/8 5/8 2 1/4 2 1/4 2 1/4 2 1/4 2 1/4 .284 .284 .284 .284 .284 15/16 15/16 15/16 15/16 15/16 21/32 21/32 21/32 21/32 21/32 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 2.7 2.74 2.9 3.15 3.1 40B33 40B34 40B35 40B36 40B37 5.54 5.70 5.86 6.02 6.18 5.260 5.419 5.578 5.737 5.896 33 34 35 36 37 B B B B B 5/8 5/8 5/8 5/8 5/8 2 1/4 2 1/4 2 1/4 2 1/4 2 1/4 .284 .284 .284 .284 .284 15/16 15/16 15/16 15/16 15/16 21/32 21/32 21/32 21/32 21/32 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 3.2 3.3 3.4 3.5 3.72 40B38 40B39 40B40 40B41 40B42 6.33 6.49 6.65 6.81 6.97 6.055 6.214 6.373 6.532 6.691 38 39 40 41 42 B B B B B 5/8 5/8 5/8 5/8 5/8 2 1/4 2 3/8 2 3/8 2 3/8 2 3/8 .284 .284 .284 .284 .284 15/16 15/16 15/16 15/16 15/16 21/32 21/32 21/32 21/32 21/32 3 1/4 3 1/2 3 1/2 3 1/2 3 1/2 3.8 3.96 4.3 4.4 4.5 40B43 40B44 40B45 40B46 40B47 7.13 7.29 7.45 7.61 7.77 6.85 7.009 7.168 7.327 7.486 43 44 45 46 47 B B B B B 5/8 5/8 5/8 5/8 5/8 2 3/8 2 3/8 2 3/8 2 3/8 2 3/8 .284 .284 .284 .284 .284 15/16 15/16 15/16 15/16 15/16 21/32 21/32 21/32 21/32 21/32 3 1/2 3 1/2 3 1/2 3 1/2 3 1/2 4.75 4.64 4.9 5.11 5.2 40B48 40B49 40B50 40B51 40B52 7.93 8.09 8.25 8.41 8.57 7.645 7.804 7.963 8.122 8.281 48 49 50 51 52 B B B B B 5/8 5/8 5/8 5/8 5/8 2 3/8 2 3/8 2 3/8 2 3/8 2 3/8 .284 .284 .284 .284 .284 15/16 15/16 15/16 15/16 15/16 21/32 21/32 21/32 21/32 21/32 3 1/2 3 1/2 3 1/2 3 1/2 3 1/2 5.4 5.38 5.7 5.32 5.87 40B53 40B54 40B55 40B56 40B57 8.73 8.89 9.04 9.20 9.36 8.440 8.599 8.758 8.917 9.076 53 54 55 56 57 B B B B B 5/8 5/8 5/8 5/8 5/8 2 3/8 2 3/8 2 3/8 2 3/8 2 3/8 .284 .284 .284 .284 .284 15/16 15/16 15/16 15/16 15/16 21/32 21/32 21/32 21/32 21/32 3 1/2 3 1/2 3 1/2 3 1/2 3 1/2 6.04 6.4 6.38 6.56 6.74 40B58 40B59 40B60 40B70 40B72 9.52 9.68 9.84 11.43 11.75 9.236 9.395 9.554 11.145 11.463 58 59 60 70 72 B B B B B 5/8 5/8 5/8 5/8 5/8 2 3/8 2 3/8 2 3/8 2 3/4 2 3/4 .284 .284 .284 .284 .284 15/16 15/16 15/16 15/16 15/16 21/32 21/32 21/32 21/32 21/32 3 1/2 3 1/2 3 1/2 4 4 7.18 7.18 7.5 10.1 10.5 40B80 40B84 40B86 40B112 13.03 13.66 15.57 18.12 12.736 13.372 15.281 17.828 80 84 86 112 B B B B 5/8 3/4 3/4 3/4 2 3/4 2 3/4 2 3/4 2 3/4 .284 .284 .284 .284 15/16 1 1 1 21/32 23/32 23/32 23/32 4 4 4 4 12.5 13.7 17.2 22.5 40B8 40B9 40B10 40B11 40B12 Outside 1.50” 1.67 1.84 2.00 2.17 Pitch 1.307” 1.462 1.618 1.775 1.932 40B13 40B14 40B15 40B16 40B17 2.30 2.49 2.65 2.80 2.96 2.089 2.247 2.405 2.563 2.721 40B18 40B19 40B20 40B21 40B22 3.14 3.30 3.45 3.62 3.75 40B23 40B24 40B25 40B26 40B27 L 7/8” 7/8 7/8 7/8 7/8 P 19/32” 19/32 19/32 19/32 19/32 H 31/32”† 1 1/8† 1 9/32† 1 7/16† 1 19/32† .1 .2 .3 .3 .4 Roller Chain Sprockets No. 40 Sprockets for , 1/2" Pitch ANSI Chain Steel Double Sprockets with Browning Split Taper® Bushings HARDENED TEETH Table No. 1 H H H P1 No. Type Outside Pitch Teeth 3/8 - 1 1/2” 2.65” 2.405” 15 11 3/8 - 1 1/2” 2.80 2.563 16 11 3/8 - 1 1/2” 2.96 2.721 17 11 1/2 - 1 3/4 3.14 2.879 18 12 T .275” .275 .275 .275 M .841” .841 .841 .841 OL 2 5/32” 2 5/32 2 5/32 2 15/32 Wt. Less L P C H Bushing 1 1/4” 1 1/8” 23/32” 2 1/2” .9 1 1/4 1 1/8 23/32 2 1/2 1.0 1 1/4 1 1/8 23/32 2 1/2 1.1 1 15/16 1 7/16 21/64 3 1.8 D40P19 D40P20 D40P21 D40P22 D40P23 P1 P1 P1 P1 P1 1/2 - 1 3/4 1/2 - 1 3/4 1/2 - 1 3/4 1/2 - 1 3/4 1/2 - 1 3/4 3.30 3.45 3.62 3.75 3.94 3.038 3.196 3.355 3.513 3.672 19 20 21 22 23 12 12 12 12 12 .275 .275 .275 .275 .275 .841 .841 .841 .841 .841 2 15/32 2 13/32 2 13/32 2 13/32 2 3/16 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 1 7/16 21/64 1 3/8 7/32 1 3/8 7/32 1 3/8 7/32 1 3/32 0 D40P24 D40P25 D40P26 D40P28 D40Q30 P1 P1 P1 P1 Q1 1/2 - 1 3/4 1/2 - 1 3/4 1/2 - 1 3/4 1/2 - 1 3/4 3/4 - 2 11/16 4.10 4.26 4.42 4.70 5.06 3.381 3.989 4.148 4.466 4.783 24 25 26 28 30 12 12 12 12 12 .275 .275 .275 .275 .275 .841 .841 .841 .841 .841 2 3/16 2 3/16 2 3/16 2 3/16 2 25/32 1 15/16 1 15/16 1 15/16 1 15/16 2 1/2 1 3/32 1 3/32 1 3/32 1 3/32 1 21/32 D40Q32 D40Q35 D40Q36 D40Q40 D40Q42 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 5.38 5.86 6.02 6.65 6.97 5.101 5.578 5.737 6.373 6.691 32 35 36 40 42 12 12 12 12 12 .275 .275 .275 .275 .275 .841 .841 .841 .841 .841 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 D40Q45 D40Q48 D40Q52 D40Q54 D40Q60 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 7.45 7.93 8.57 8.89 9.84 7.168 7.645 8.281 8.599 9.554 45 48 52 54 60 12 12 12 12 12 .275 .275 .275 .275 .275 .841 .841 .841 .841 .841 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 D40Q68 D40Q72 D40Q76 D40Q84 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 11.12 11.75 12.39 13.66 10.826 11.463 12.099 13.372 68 72 76 84 12 12 12 12 .275 .275 .275 .275 .841 .841 .841 .841 D40Q95 D40Q96 D40Q102 D40Q112 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 15.41 15.57 16.53 18.12 15.122 95 15.281 96 16.236 102 17.828 112 12 12 12 12 .275 .275 .275 .275 .841 .841 .841 .841 Part No. Bushing D40H15 D40H16 D40H17 D40P18 DIAMETERS Bore Range DIAMETERS Part No. Bushing Bore Range D40SK36 D40SK40 D40SK42 D40SK45 D40SK48 SK SK SK SK SK 1/2-2 5/8 1/2-2 5/8 1/2-2 5/8 1/2-2 5/8 1/2-2 5/8 D40SK52 D40SK54 D40SK60 D40SF68 D40SF72 D40SF76 D40SF84 D40SF95 D40B17 D40B18 D40B19 D40B20 D40B21 D40B22 3 3 3 3 3 1.4 1.6 1.8 2.0 2.0 0 0 0 0 0 3 3 3 3 4 1/8 2.2 2.5 2.7 3.1 4.2 1 21/32 1 21/32 1 21/32 1 21/32 1 21/32 0 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 5.3 6.1 6.5 7.9 8.9 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1 21/32 1 21/32 1 21/32 1 21/32 1 21/32 0 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 10.1 11.8 12.6 14.3 17.4 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 1 21/32 1 21/32 1 21/32 1 21/32 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 21.5 25.0 26.9 34.1 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 1 21/32 1 21/32 1 21/32 1 21/32 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 42.0 44.1 48.5 61.0 Outside 6.02” 6.65 6.97 7.45 7.93 Type H 3 7/8” 3 7/8 3 7/8 3 7/8 3 7/8 Wt. Less Bushing 5.1 6.5 7.2 8.4 9.7 DIMENSIONS No. Teeth Pitch 5.737” 6.373 6.691 7.168 7.645 QD-4 QD-4 QD-4 QD-4 QD-4 T M OL L 36 .275” .841” 2 11/32” 1 15/16” 40 .275 .841 2 11/32 1 15/16 42 .275 .841 2 11/32 1 15/16 45 .275 .841 2 11/32 1 15/16 48 .275 .841 2 11/32 1 15/16 SK SK SK SF SF 1/2-2 5/8 8.57 8.281 1/2-2 5/8 8.89 8.599 1/2-2 5/8 9.84 9.554 1/2-2 15/16 11.12 10.826 1/2-2 15/16 11.75 11.463 QD-4 QD-4 QD-4 QD-4 QD-4 52 54 60 68 72 .275 .275 .275 .275 .275 SF SF SF 1/2-2 15/16 12.39 12.099 QD-4 1/2-2 15/16 13.66 13.372 QD-4 1/2-2 15/16 15.41 15.122 QD-4 76 84 95 .275 .841 2 15/32 2 1/16 .275 .841 2 15/32 2 1/16 .275 .841 2 15/32 2 1/16 .841 .841 .841 .841 .841 2 11/32 2 11/32 2 11/32 2 15/32 2 15/32 P 13/16” 13/16 13/16 13/16 13/16 C 13/32” 13/32 13/32 13/32 13/32 1 15/16 13/16 13/32 3 7/8 1 15/16 13/16 13/32 3 7/8 1 15/16 13/16 13/32 3 7/8 2 1/16 7/8 13/32 4 5/8 2 1/16 7/8 13/32 4 5/8 7/8 7/8 7/8 11.6 12.6 15.7 20.5 23.1 13/32 4 5/8 13/32 4 5/8 13/32 4 5/8 25.8 31.8 41.0 DIMENSIONS L P H Max. 1 1/2” 21/32” 1 7/16”† 1 1/2 21/32 1 19/32† 1 1/2 21/32 1 11/16 1 1/2 21/32 1 11/16 1 1/2 21/32 1 13/16 1 1/2 21/32 2 Wt. Lbs. Steel Double Type "B" Minimum Bore Sprockets HARDENED TEETH Table No. 3 D40B11 D40B12 D40B13 D40B14 D40B15 D40B16 DIMENSIONS Steel Double Sprockets with Q-D® Bushings Table No. 2 Part No. 40 DIAMETERS Outside Pitch 2.00” 1.775” 2.17 1.932 2.33 2.089 2.49 2.247 2.65 2.405 2.80 2.563 2.96 3.14 3.28 3.45 3.62 3.78 2.721 2.879 3.038 3.196 3.355 3.513 No. Teeth Type 11 12 13 14 15 16 17 18 19 20 21 22 BORE DB DB DB DB DB DB Stock 1/2” 1/2” 1/2” 1/2” 1/2” 5/8 Max.* 3/4” 15/16 1 1 1/8 1 1/4 1 3/8 T .275” .275 .275 .275 .275 .275 M .841” .841 .841 .841 .841 .841 DB DB DB DB DB DB 5/8 5/8 5/8 5/8 5/8 5/8 1 7/16 1 1/2 1 3/4 1 7/8 1 7/8 1 7/8 .275 .275 .275 .275 .275 .275 .841 .841 .841 .841 .841 .841 LARGER SIZES AND NOTES ON NEXT PAGE 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 21/32 21/32 21/32 21/32 21/32 21/32 2 1/8 2 5/16 2 1/2 2 5/8 2 3/4 2 7/8 .4 .6 .7 .8 1.0 1.4 1.5 1.7 2.3 2.6 2.9 3.1 Standard Keyseats Table No. 4 Bore Range Keyseat 1/2" - 9/16" 5/8 - 7/8 15/16 - 1 1/4 1 5/16 - 1 3/8 1 7/16 - 1 3/4 1 13/16 - 2 1/4 2 5/16 - 2 3/4 2 13/16 - 3 1/4 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 1 3/8" Bore Bushings also avail able with 3/8" x 3/16" Keyseat. H-20 Roller Chain Sprockets 40 DIAMETERS Part No. Outside D40B23 D40B24 D40B25 D40B26 D40B30 BORE DIMENSIONS L P M Max. Pitch No. Teeth Type 3.94” 4.10 4.26 4.42 5.06 3.672” 3.831 3.989 4.148 4.783 23 24 25 26 30 DB DB DB DB DB 5/8 5/8 5/8 5/8 7/8 2” 2 1/4 2 1/4 2 1/4 2 1/4 .275” .275 .275 .275 .275 .841” .841 .841 .841 .841 1 1/2” 1 1/2 1 1/2 1 1/2 1 1/2 D40B32 D40B35 D40B36 D40B40 D40B42 5.38 5.86 6.02 6.65 6.97 5.101 5.578 5.737 6.373 6.691 32 35 36 40 42 DB DB DB DB DB 7/8 7/8 7/8 7/8 7/8 2 1/4 2 1/4 2 3/4 2 3/4 2 3/4 .275 .275 .275 .275 .275 .841 .841 .841 .841 .841 D40B45 D40B48 D40B52 D40B54 D40B60 7.45 7.93 8.57 8.89 9.84 7.168 7.645 8.281 8.599 9.554 45 48 52 54 60 DB DB DB DB DB 7/8 7/8 7/8 7/8 7/8 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 .275 .275 .275 .275 .275 D40B68 D40B72 D40B76 D40B84 11.12 11.75 12.39 13.66 10.826 11.463 12.099 13.372 68 72 76 84 DB DB DB DB 1 3/16 1 3/16 1 3/16 1 3/16 2 3/4 2 3/4 2 3/4 3 D40B96 D40B102 D40B112 15.57 16.53 18.12 15.281 16.236 17.828 96 102 112 DB DB DB 1 3/16 1 3/16 1 3/16 3 3 3 Stock H Wt. Lbs. 21/32” 21/32 21/32 21/32 21/32 3” 3 1/4 3 1/4 3 1/4 3 1/4 3.3 3.6 3.9 4.1 5.1 1 1/2 1 1/2 1 1/2 1 3/4 1 3/4 21/32 21/32 21/32 29/32 29/32 3 1/4 3 1/4 4 4 4 5.8 6.8 7.9 10.1 10.8 .841 .841 .841 .841 .841 1 3/4 1 3/4 1 3/4 1 3/4 1 3/4 29/32 29/32 29/32 29/32 29/32 4 4 4 4 4 12.1 13.3 15.2 16.2 19.3 .275 .275 .275 .275 .841 .841 .841 .841 2 1/8 2 1/8 2 1/8 2 1/8 1 9/32 1 9/32 1 9/32 1 9/32 4 1/4 4 1/4 4 1/4 4 1/2 25.7 28.3 31.0 37.6 .275 .275 .275 .841 .841 .841 2 1/8 2 1/8 2 1/8 1 9/32 1 9/32 1 9/32 4 1/2 4 1/4 4 1/2 47.7 53.3 63.3 Max.* T SMALLER SIZES ON PRECEDING PAGE HARDENED TEETH Steel Double Type "B" Minimum Bore Sprockets Table No. 1 * Maximum bore shown is with standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway †Hub is recessed for chain clearance. These Type “B” sprockets are made without keyways or setscrews. They are furnished with a minimum bore which can be rebored to size and keywayed for a reasonable extra charge. Steel Triple Sprockets with Browning Split Taper® Bushings Bushing T40P18 T40P19 T40P20 T40P23 T40P24 P1 P1 P1 P1 P1 T40P25 T40P27 T40Q30 T40Q35 T40Q36 P1 P1 Q1 Q1 Q1 1/2-1 3/4 1/2-1 3/4 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 4.26 4.58 5.06 5.86 6.02 3.989 4.307 4.783 5.578 5.737 25 27 30 35 36 T40Q42 T40Q48 T40Q52 T40Q54 T40Q60 Q1 Q1 Q1 Q1 Q1 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 6.97 7.93 8.57 8.89 9.84 6.691 7.645 8.281 8.599 9.554 T40Q68 T40Q72 T40Q76 T40Q84 T40Q95 T40Q102 Bore Range No. Type Outside Pitch Teeth 1/2-1 3/4” 3.14” 2.879” 18 22 1/2-1 3/4 3.30 3.038 19 22 1/2-1 3/4 3.46 3.196 20 22 1/2-1 3/4 3.94 3.672 23 23 1/2-1 3/4 4.10 3.831 24 23 DIMENSIONS M 1.407” 1.407 1.407 1.407 1.407 23 23 22 22 22 .275 .275 .275 .275 .275 1.407 2 9/32 1 15/16 5/8 1.407 2 9/32 1 15/16 5/8 1.407 2 25/32 2 1/2 1 3/32 1.407 2 25/32 2 1/2 1 3/32 1.407 2 25/32 2 1/2 1 3/32 42 48 52 54 60 22 22 22 22 22 .275 .275 .275 .275 .275 1.407 1.407 1.407 1.407 1.407 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1 3/32 1 3/32 1 3/32 1 3/32 1 3/32 0 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 11.1 15.2 18.7 19.9 25.3 Q1 Q1 3/4-2 11/16 11.12 10.826 68 3/4-2 11/16 11.75 11.463 72 22 22 .275 1.407 2 25/32 .275 1.407 2 25/32 2 1/2 2 1/2 1 3/32 1 3/32 0 0 4 1/8 4 1/8 33.5 37.9 Q1 Q1 Q1 Q1 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 22 22 22 22 .275 .275 .275 .275 2 1/2 2 1/2 2 1/2 2 1/2 1 3/32 1 3/32 1 3/32 1 3/32 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 42.5 524 67.9 78.5 12.39 13.66 15.41 16.53 12.099 13.372 15.122 16.236 76 84 95 102 1.407 1.407 1.407 1.407 OL L P C 2 15/32” 1 15/16” 2 27/32” 29/32” 2 15/32 1 15/16 2 27/32 29/32 2 31/32 1 15/16 1 5/16 25/32 2 9/32 1 15/16 5/8 3/32 2 9/32 1 15/16 5/8 3/32 2 25/32 2 25/32 2 25/32 2 25/32 H 3” 3 3 3 3 Wt. Less Bushing 1.9 1.8 2.0 2.3 2.6 T .275” .275 .275 .275 .275 3/32 3 3/32 3 0 4 1/8 0 4 1/8 0 4 1/8 3.0 3.3 4.5 6.9 7.6 Steel Triple Sprockets with Q-D® Bushings Table No. 3 H-21 DIAMETERS Part No. HARDENED TEETH Table No. 2 Part No. Bushing Bore Range T40SK36 T40SK42 T40SK48 T40SK52 T40SK60 SK SK SK SK SK 1/2-2 5/8” 1/2-2 5/8 1/2-2 5/8 1/2-2 5/8 1/2-2 5/8 T40SF68 T40SF72 T40SF84 SF SF SF DIAMETERS DIMENSIONS OL L Max. 2 11/32” 1 15/16” 2 11/32 1 15/16 2 11/32 1 15/16 2 11/32 1 15/16 2 11/32 1 15/16 Type No. Teeth QD-8 QD-8 QD-8 QD-8 QD-8 36 42 48 52 60 T .275” .275 .275 .275 .275 M 1.407” 1.407 1.407 1.407 1.407 1/2-2 15/16 11.12 10.826 QD-8 1/2-2 15/16 11.75 11.463 QD-8 1/2-2 15/16 13.66 13.372 QD-8 68 72 84 .275 .275 .275 1.407 2 13/32 1.407 2 13/32 1.407 2 13/32 Outside 6.02” 6.97 7.93 8.57 9.84 Pitch 5.737” 6.691 7.645 8.281 9.554 2 1/16 2 1/16 2 1/16 P 21/32” 21/32 21/32 21/32 21/32 H 3 7/8” 3 7/8 3 7/8 3 7/8 3 7/8 Wt. Less Bushing 6.8 10.4 14.5 17.6 24.6 23/32 23/32 23/32 4 5/8 4 5/8 4 5/8 31.8 36.1 50.6 Roller Chain Sprockets Sprockets for No. 50 , 5/8" Pitch ANSI Chain Steel Single Sprockets with Browning Split Taper® Bushings Table No. 1 HARDENED TEETH 50 DIAMETERS Wt. Less C H Bushing 13/32” 2” 0.5 13/32 2 0.5 1/16 2 0.5 1/4 2 1/2 0.6 5/32 2 1/2 0.6 11 12 13 13 14 3 3 3 3 3 DIMENSIONS T OL L P Nom. 0.343” 1 19/32” 1” 1 1/16” 0.343 1 19/32 1 1 1/16 0.343 1 1/4 1 23/32 0.343 1 23/32 1 1/4 1 11/64 0.343 1 5/8 1 1/4 1 1/16 3.006 3.006 3.204 3.204 3.401 15 15 16 16 17 3 4 3 4 3 0.343 0.343 0.343 0.343 0.343 1 1/2 1 1/4 2 3/16 1 15/16 1 1/2 1 1/4 2 3/16 1 15/16 1 1/2 1 1/4 1 1/16 5/32 1 19/32 0 1 1/16 5/32 1 19/32 0 1 1/16 5/32 2 1/2 3 2 1/2 3 2 1/2 0.8 1.1 0.9 1.3 1.0 3.72 3.92 3.92 4.12 4.12 3.401 3.599 3.599 3.797 3.797 17 18 18 19 19 4 3 4 3 4 0.343 0.343 0.343 0.343 0.343 2 3/16 1 15/16 1 1/2 1 1/4 2 3/16 1 15/16 1 1/2 1 1/4 2 3/16 1 15/16 1 19/32 0 1 1/16 5/32 1 19/32 0 31/32 1/16 1 19/32 0 3 2 1/2 3 2 1/2 3 1.4 1.0 1.6 1.1 1.8 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 4.32 4.32 4.52 4.52 4.72 3.995 3.995 4.194 4.194 4.392 20 20 21 21 22 3 4 3 4 3 0.343 0.343 0.343 0.343 0.343 1 1/2 1 1/4 2 3/16 1 15/16 1 1/2 1 1/4 2 3/16 1 15/16 1 1/2 1 1/4 31/32 1/16 1 19/32 0 31/32 1/16 1 19/32 0 31/32 1/16 2 1/2 3 2 1/2 3 2 1/2 1.5 2.0 1.4 2.1 1.5 P1 H P1 Q1 H 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 3/4 - 2 11/16 3/8 - 1 1/2 4.70 4.92 4.92 4.92 5.12 4.392 4.590 3.599 3.599 4.788 22 23 23 23 24 4 3 4 4 3 0.343 2 3/16 1 15/16 0.343 1 1/2 1 1/4 0.343 2 3/16 1 15/16 0.343 2 25/32 2 1/2 0.343 1 1/2 1 1/4 1 19/32 0 31/32 1/16 1 19/32 0 2 5/32 0 31/32 1/16 3 2 1/2 3 4 1/8 2 1/2 2.3 1.7 2.4 3.4 1.8 H50P24 H50Q24 H50H25 H50P25 H50Q25 P1 Q1 H P1 Q1 1/2 - 1 3/4 3/4 - 2 11/16 3/8 - 1 1/2 1/2 - 1 3/4 3/4 - 2 11/16 5.12 5.12 5.32 5.32 5.32 4.788 4.788 4.987 4.987 4.987 24 24 25 25 25 4 4 3 4 4 0.343 2 3/16 2 15/16 0.343 2 25/32 2 1/2 0.343 1 1/2 1 1/4 0.343 2 3/16 2 15/16 0.343 2 25/32 2 1/2 1 19/32 0 2 5/32 0 31/32 1/16 1 19/32 0 2 5/32 0 3 4 1/8 2 1/2 3 4 1/8 2.5 3.4 1.9 2.6 3.7 H50H26 H50P26 H P1 3/8 - 1 1/2 1/2 - 1 3/4 5.52 5.52 5.185 5.185 26 26 3 4 0.343 0.343 1 1/2 1 1/4 31/32 1/16 2 3/16 2 15/16 1 19/32 0 2 1/2 3 2.0 2.9 Part No. Bushing Bore Range H50G11 H50G12 H50G13 H50H13 H50H14 G G G H H 3/8 - 1” 3/8 - 1 3/8 - 1 3/8 - 1 1/2 3/8 - 1 1/2 Outside 2.50” 2.70 2.91 2.91 3.11 Pitch 2.219” 2.415 2.612 2.612 2.809 H50H15 H50P15 H50H16 H50P16 H50H17 H P1 H P1 H 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 3.32 3.32 3.52 3.52 3.72 H50P17 H50H18 H50P18 H50H19 H50P19 P1 H P1 H P1 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 H50H20 H50P20 H50H21 H50P21 H50H22 H P1 H P1 H H50P22 H50H23 H50P23 H50Q23 H50H24 No. Type Teeth Where two sprockets with the same number of teeth but different bushings are offered, we suggest using the sprocket bushing for heavier service drives. Standard Keyseats Table No. 2 Bore Range Keyseat 3/8" - 7/16" 1/2 - 9/16 5/8 - 7/8 15/16 - 1 1/4 1 5/16 - 1 3/8 1 7/16 - 1 3/4 1 13/16 - 2 1/4 2 5 /16 - 2 3/4 2 13/16 - 3 1/4 None 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-22 Roller Chain Sprockets Steel Single Sprockets with Browning Split Taper® Bushings Table No. 1 HARDENED TEETH 50 26 27 27 27 28 4 3 4 4 3 Wt. DIMENSIONS Less T OL L P C H Bushing Nom. 0.343 2 25/32 2 1/2 2 5/32 0 4 1/8 3.8 0.343 1 1/2 1 1/4 31/32 1/16 2 1/2 2.2 0.343 2 3/16 2 15/16 1 19/32 0 3 3.0 0.343 2 25/32 2 1/2 2 5/32 0 4 1/8 3.9 0.343 1 1/2 1 1/4 31/32 1/16 2 1/2 2.5 5.582 5.582 5.781 5.979 5.979 28 28 29 30 30 4 4 4 3 4 0.343 2 3/16 2 15/16 0.343 2 25/32 2 1/2 0.343 2 3/16 2 15/16 0.343 1 1/2 1 1/4 0.343 2 3/16 2 15/16 1 19/32 0 3 2 5/32 0 4 1/8 1 19/32 0 3 31/32 1/16 2 1/2 1 19/32 0 3 3.2 4.0 3.3 2.9 3.5 6.32 6.72 6.92 7.12 7.32 5.979 6.376 6.575 6.774 6.972 30 32 33 34 35 4 3 3 3 3 0.343 2 25/32 0.343 1 1/2 0.343 1 1/2 0.343 1 1/2 0.343 1 1/2 2 1/2 1 1/4 1 1/4 1 1/4 1 1/4 2 5/32 31/32 31/32 31/32 31/32 0 1/16 1/16 1/16 1/16 4 1/8 2 1/2 2 1/2 2 1/2 2 1/2 5.6 3.2 3.4 3.7 3.8 3/8 - 1 1/2 3/8 - 1 1/2 3/8 - 1 1/2 7.52 7.92 8.32 7.171 7.569 7.996 36 38 40 3 3 3 0.343 0.343 0.343 1 1/4 1 1/4 1 1/4 31/32 31/32 31/32 1/16 2 1/2 1/16 2 1/2 1/16 2 1/2 4.0 4.4 4.8 P1 P1 Q1 P1 P1 1/2 - 1 3/4 1/2 - 1 3/4 3/4 - 2 11/16 1/2 - 1 3/4 1/2 - 1 3/4 6.52 6.72 6.72 6.92 7.12 6.178 6.376 6.376 6.575 6.774 31 32 32 33 34 4 4 4 4 4 0.343 2 3/16 2 15/16 0.343 2 3/16 2 15/16 0.343 2 25/32 2 1/2 0.343 2 3/16 2 15/16 0.343 2 3/16 2 15/16 1 19/32 1 19/32 2 5/32 1 19/32 1 19/32 0 0 0 0 0 3 3 4 1/8 3 3 3.6 3.9 6.1 4.1 4.3 50P35 50Q35 50P36 50Q36 50Q37 P1 Q1 P1 Q1 Q1 1/2 - 1 3/4 3/4 - 2 11/16 1/2 - 1 3/4 3/4 - 2 11/16 3/4 - 2 11/16 7.32 7.32 7.52 7.52 7.72 6.972 9.972 7.171 7.171 7.370 35 35 36 36 37 4 4 4 4 4 0.343 2 3/16 2 15/16 0.343 2 25/32 2 1/2 0.343 2 3/16 2 15/16 0.343 2 25/32 2 1/2 0.343 2 25/32 2 1/2 1 19/32 2 5/32 1 19/32 2 5/32 2 5/32 0 0 0 0 0 3 4 1/8 3 4 1/8 4 1/8 4.3 6.8 4.8 6.8 7.0 50Q38 50Q39 50Q40 50Q41 50Q42 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 7.92 8.12 8.32 8.52 8.72 7.569 7.767 7.966 8.165 8.363 38 39 40 41 42 4 4 4 4 4 0.343 0.343 0.343 0.343 0.343 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 5/32 2 5/32 2 5/32 2 5/32 2 5/32 0 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 7.4 7.6 8.0 8.2 8.3 50Q44 50Q45 50Q47 50Q48 50Q50 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 9.11 3/4 - 2 11/16 9.31 3/4 - 2 11/16 9.71 3/4 - 2 11/16 9.91 3/4 - 2 11/16 10.31 8.761 8.960 9.357 9.556 9.954 44 45 47 48 50 4 4 4 4 4 0.343 0.343 0.343 0.343 0.343 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 5/32 2 5/32 2 5/32 2 5/32 2 5/32 0 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 8.6 9.0 9.3 9.6 9.8 50Q54 50Q56 50Q60 50Q70 50Q72 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 11.11 11.50 12.30 14.29 14.69 10.749 11.147 11.942 13.931 14.329 54 56 60 70 72 4 4 4 4 4 0.343 0.343 0.343 0.343 0.343 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 5/32 2 5/32 2 5/32 2 5/32 2 5/32 0 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 11.3 12.3 13.3 16.9 18.1 50Q80 50Q84 50Q96 50Q112 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 16.28 17.08 19.47 22.65 15.92 16.715 19.102 22.285 80 84 96 112 4 4 4 4 0.343 0.343 0.343 0.343 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 2 5/32 2 5/32 2 5/32 2 5/32 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 21.1 24.3 29.8 39.3 DIAMETERS Part No. Bushing Bore Range H50Q26 H50H27 H50P27 H50Q27 H50H28 Q1 H P1 Q1 H 3/4 - 2 11/16 3/8 - 1 1/2 1/2 - 1 3/4 3/4 - 2 11/16 3/8 - 1 1/2 Outside 5.52 5.72 5.72 5.72 5.92 Pitch 5.185 5.384 5.384 5.384 5.582 H50P28 H50Q28 H50P29 H50H30 H50P30 P1 Q1 P1 H P1 1/2 - 1 3/4 3/4 - 2 11/16 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 5.92 5.92 6.12 6.32 6.32 H50Q30 H50H32 H50H33 H50H34 H50H35 Q1 H H H H 3/4 - 2 11/16 3/8 - 1 1/2 3/8 - 1 1/2 3/8 - 1 1/2 3/8 - 1 1/2 H50H36 H50H38 H50H40 H H H 50P31 50P32 50Q32 50P33 50P34 No. Type Teeth 1 1/2 1 1/2 1 1/2 Where two sprockets with the same number of teeth but different bushings are offered, we suggest using the sprocket bushing for heavier service drives. H-23 Roller Chain Sprockets Sprockets for No. 50 , 5/8" Pitch ANSI Chain Steel Single Sprockets with Q-D® Bushings Table No. 1 HARDENED TEETH 50 Diameters Dimensions Part Bore No. Bushing Type No. Range Teeth T Nom. Outside Pitch OL L P H50JA12* JA 1/2 - 1 1/4” 2.71” 2.415” QD-1 12 .343” 1 5/16” 1” 13/16” H50JA13* JA 1/2 - 1 1/4 2.91 2.612 QD-1 13 .343 1 5/16 1 13/16 H50JA14 JA 1/2 - 1 1/4 3.11 2.803 QD-1 14 .343 1 5/16 1 13/16 H50JA15 JA 1/2 - 1 1/4 3.32 3.006 QD-1 15 .343 1 5/16 1 13/16 H50JA16 JA 1/2 - 1 1/4 3.52 3.204 QD-1 16 .343 1 5/16 1 13/16 H 2” 2 2 2 2 Wt. Less Bushing .35 .44 .60 .69 .79 H50SH17 H50SH18 H50SH19 H50SDS20 H50SDS21 SH SH SH SDS SDS 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 2 1/2 - 2 3.72 3.92 4.12 4.32 4.52 3.401 3.599 3.797 3.995 4.194 QD-1 QD-1 QD-1 QD-1 QD-1 17 18 19 20 21 .343 .343 .343 .343 .343 1 23/32 1 23/32 1 23/32 1 21/32 1 21/32 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 1 5/32 1 5/32 1 5/32 1 3/32 1 3/32 2 11/16 2 11/16 2 11/16 3 1/8 3 1/8 1.09 1.26 1.40 1.37 1.49 H50SDS22 H50SDS23 H50SDS24 H50SDS25 H50SDS26 SDS SDS SDS SDS SDS 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 4.72 4.92 5.12 5.32 5.52 4.392 4.590 4.788 4.987 5.185 QD-1 QD-1 QD-1 QD-1 QD-1 22 23 24 25 26 .343 .343 .343 .343 .343 1 21/32 1 21/32 1 21/32 1 21/32 1 21/32 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 1 3/32 1 3/32 1 3/32 1 3/32 1 3/32 3 1/8 3 1/8 3 1/8 3 1/8 3 1/8 1.62 1.75 1.88 2.01 2.15 H50SDS27 H50SDS28 H50SDS30 50SDS32 50SDS35 50SDS36 SDS SDS SDS SDS SDS SDS 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 5.72 5.92 6.32 6.72 7.32 7.52 5.384 5.582 5.979 6.376 6.972 7.171 QD-1 QD-1 QD-1 QD-1 QD-1 QD-1 27 28 30 32 35 36 .343 .343 .343 .343 .343 .343 1 21/32 1 21/32 1 21/32 1 21/32 1 21/32 1 21/32 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 1 3/32 1 3/32 1 3/32 1 3/32 1 3/32 1 3/32 3 1/8 3 1/8 3 1/8 3 1/8 3 1/8 3 1/8 2.30 2.45 2.77 3.11 3.66 3.86 50SDS40 50SDS42 50SDS45 50SDS48 50SK54 50SK60 SDS SDS SDS SDS SK SK 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 5/8 1/2 - 2 5/8 8.32 8.72 9.31 9.91 11.11 12.30 7.966 8.363 8.960 9.556 10.749 11.942 QD-1 QD-1 QD-1 QD-1 QD-1 QD-1 40 42 45 48 54 60 .343 .343 .343 .343 .343 .343 1 21/32 1 21/32 1 21/32 1 21/32 2 11/32 2 11/32 1 5/16 1 5/16 1 5/16 1 5/16 1 15/16 1 15/16 1 3/32 1 3/32 1 3/32 1 3/32 1 23/32 1 23/32 3 1/8 3 1/8 3 1/8 3 1/8 3 7/8 3 7/8 4.70 5.15 5.86 6.63 9.24 11.1 50SK70 50SK72 50SF80 50SF84 50SF96 50SF112 SK SK SF SF SF SF 1/2 - 2 5/8 1/2 - 2 5/8 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 14.29 14.69 16.28 17.08 19.47 22.65 13.931 14.329 15.920 16.715 19.102 22.285 QD-1 QD-1 QD-1 QD-1 QD-1 QD-1 70 72 80 84 96 112 .343 .343 .343 .343 .343 .343 2 11/32 2 11/32 2 11/32 2 11/32 2 11/32 2 11/32 1 15/16 1 15/16 2 1/16 2 1/16 2 1/16 2 1/16 1 23/32 1 23/32 1 25/32 1 25/32 1 25/32 1 25/32 3 7/8 3 7/8 4 5/8 4 5/8 4 5/8 4 5/8 14.7 15.5 19.4 21.2 27.2 36.4 * Bushings mounts with capscrews on “A” side only Table No. 2 Steel Single Sprockets with Browning Split Taper® Bushings HARDENED TEETH DIAMETERS No. Part Type No. Outside Pitch Teeth 5/8” 3/4” 7/8” STOCK Steel Sprockets H509 2.09” 1.827” 9 1 x x H5010 2.30 2.023 10 1 x x x H5011 2.50 2.219 11 1 x x x H5012 2.70 2.415 12 1 x x x H5013 2.91 2.612 13 1 x x x H5014 3.11 2.809 14 1 x x x H5015 3.32 3.006 15 1 x x x H5016 3.52 3.204 16 1 x x x H5017 3.72 3.401 17 1 x x x H5018 3.92 3.599 18 1 x x x H5019 4.12 3.797 19 1 x x x H5020 4.32 3.995 20 1 x x H5021 4.52 4.194 21 1 x x H5022 4.72 4.392 22 1 x x H5023 4.92 4.590 23 1 x x H5024 5.12 4.788 24 1 x x 1 x x H5025 5.32 4.987 25 H5026 5.52 5.185 26 1 x x H5027 5.72 5.384 27 1 x x H5028 5.92 5.582 28 1 x x H5029 6.12 5.781 29 1 x x H5030 6.32 5.979 30 1 x x 5032 6.72 6.376 32 1 x 5033 6.92 6.575 33 1 5034 7.12 6.774 34 1 5035 7.32 6.972 35 1 x 5036 7.52 7.171 36 1 x 5038 7.92 7.569 38 1 5039 8.12 7.767 39 1 5040 8.32 7.966 40 1 x 5041 8.52 8.165 41 1 5042 8.72 8.363 42 1 5045 9.31 8.960 45 1 5048 9.91 9.556 48 1 5049 10.11 9.755 49 1 5050 10.31 9.954 50 1 5060 12.30 11.942 60 1 - 1” x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x STOCK BORES MARKED “X” DIMENSIONS 1 1/8” 1 3/16” 1 1/4” 1 3/8” 1 7/16” 1 1/2” 1 5/8” 1 11/16” 1 3/4” 1 15/16” T Nom. L P x x x x x x x x x x x x x x x x x x x x - x x x x x x x x x x x x x x x x x x x x x x x x x - x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x - x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x - x - x x x - x x x .343” .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 .343 1” 1 1 1 1 1 1 1 1 1 1 1 1 1 1 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 Wt. Lbs. 21/32” 21/32 21/32 21/32 21/32 21/32 21/32 21/32 21/32 21/32 21/32 21/32 21/32 21/32 21/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 23/32 .3 .5 .6 .7 .8 1.0 1.3 1.5 1.6 1.8 1.9 2.5 2.6 2.7 3.3 3.0 3.6 3.8 3.9 4.1 4.3 4.4 4.7 4.9 5.1 5.4 5.6 5.9 6.0 6.2 6.3 6.5 6.9 7.2 7.5 7.8 10.8 All Stock Finished Bore Sprockets are furnished with Standard Keyway on Centerline of Tooth and Hollow Head Setscrew over Keyway. Sprockets with HARDENED TEETH have an additional Setscrew at 90° to Keyway. H-24 Roller Chain Sprockets Type "A" Steel Plate Sprockets Table No. 1 Part No. Outside Dia. 50A10 50A11 50A12 50A13 50A14 2.30” 2.50 2.70 2.91 3.11 2.023” 2.219 2.415 2.612 2.809 10 11 12 13 14 5/8” 5/8 5/8 5/8 5/8 50A15 50A16 50A17 50A18 50A19 3.32 3.52 3.72 3.92 4.12 3.006 3.204 3.401 3.599 3.797 15 16 17 18 19 50A20 50A21 50A22 50A23 50A24 4.32 4.52 4.70 4.90 5.12 3.995 4.194 4.392 4.590 4.788 50A25 50A26 50A27 50A28 50A29 5.32 5.52 5.72 5.92 6.12 50A30 50A31 50A32 50A33 50A34 50A35 50A36 50A37 50A38 50A39 Wt. Lbs. Part No. Outside Dia. .343” .343 .343 .343 .343 .2 .3 .3 .4 .4 50A40 50A41 50A42 50A43 50A44 8.32” 8.52 8.72 8.91 9.11 7.966” 8.165 8.363 8.562 8.761 40 41 42 43 44 3/4” 3/4 3/4 3/4 3/4 .343” .343 .343 .343 .343 4.6 4.8 5.0 5.3 5.5 5/8 5/8 5/8 5/8 5/8 .343 .343 .343 .343 .343 .5 .6 .6 .8 .8 50A45 50A46 50A47 50A48 50A49 9.31 9.51 9.71 9.91 10.11 8.960 9.159 9.357 9.556 9.755 45 46 47 48 49 3/4 3/4 3/4 3/4 3/4 .343 .343 .343 .343 .343 5.7 5.9 6.1 6.4 6.6 20 21 22 23 24 3/4 3/4 3/4 3/4 3/4 .343 .343 .343 .343 .343 .9 1.0 1.1 1.2 1.4 50A50 50A51 50A52 50A53 50A54 13.31 10.51 10.71 10.91 11.11 9.954 10.153 10.351 10.550 10.749 50 51 52 53 54 3/4 3/4 3/4 3/4 3/4 .343 .343 .343 .343 .343 6.8 7.1 7.4 7.7 8.0 4.987 5.185 5.384 5.582 5.781 25 26 27 28 29 3/4 3/4 3/4 3/4 3/4 .343 .343 .343 .343 .343 1.5 1.6 1.8 2.1 2.3 50A55 50A56 50A57 50A58 50A59 11.31 11.50 11.70 11.90 12.10 10.948 11.147 11.346 11.544 11.743 55 56 57 58 59 3/4 3/4 3/4 3/4 3/4 .343 .343 .343 .343 .343 8.3 8.6 8.9 9.2 9.5 6.32 6.52 6.72 6.92 7.12 5.979 6.178 6.376 6.575 6.774 30 31 32 33 34 3/4 3/4 3/4 3/4 3/4 .343 .343 .343 .343 .343 2.5 2.6 2.8 3.0 3.3 50A60 50A70 50A72 50A76 50A80 12.30 14.29 14.69 15.49 16.28 11.942 13.931 14.329 15.124 15.920 60 70 72 76 80 3/4 3/4 3/4 3/4 3/4 .343 .343 .343 .343 .343 9.9 13.4 14.2 15.8 17.6 7.32 7.52 7.72 7.92 8.12 6.972 7.171 7.370 7.569 7.767 35 36 37 38 39 3/4 3/4 3/4 3/4 3/4 .343 .343 .343 .343 .343 3.4 3.6 3.8 4.0 4.2 50A84 50A95 50A96 50A112 17.08 19.27 19.47 22.62 16.715 84 18.903 95 19.102 96 22.285 112 3/4 3/4 3/4 3/4 .343 .343 .343 .343 19.4 24.8 25.3 34.5 Standard Keyseats Table No. 3 Bore Range Keyseat 3/8" — 7/16" 1/2 — 9/16 5/8 — 7/8 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 None 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 1 3 / 8 " B o re B u s h in g s als o availa b l e with 3/8 " x 3 /1 6 " K eyseat . H-25 Pitch No. Stock T Dia. Teeth Bore (Norm.) Pitch No. Stock T Dia. Teeth Bore (Norm.) Wt. Lbs. Type "B" Steel Plate Sprockets Table No. 2 Part No. 50 DIAMETERS No. Teeth Type 8 9 10 11 12 2.612 2.809 3.006 3.204 3.401 3.92 4.12 4.32 4.52 4.72 50B23 50B24 50B25 50B26 50B27 BORE DIMENSIONS L P Max. 1” 21/32” 1 21/32 1 21/32 1 21/32 1 21/32 Wt. Lbs. B B B B B Stock 1/2” 5/8 5/8 5/8 5/8 Max.* 5/8” 3/4 7/8 1 1 1/4 T Nom. .343” .343 .343 .343 .343 13 14 15 16 17 B B B B B 5/8 5/8 5/8 5/8 5/8 1 5/16 1 7/16 1 1/2 1 3/4 1 7/8 .343 .343 .343 .343 .343 1 1 1 1 1 21/32 21/32 21/32 21/32 21/32 2 11/64† 2 1/8 2 3/8 2 9/16 2 11/16 .8 1.0 1.3 1.6 1.8 3.599 3.797 3.995 4.194 4.392 18 19 20 21 22 B B B B B 5/8 5/8 3/4 3/4 3/4 1 7/8 2 2 2 1/4 2 1/4 .343 .343 .343 .343 .343 1 1 1 1 1 21/32 21/32 21/32 21/32 21/32 2 7/8 3 3 3 3/8 3 1/4 2.0 2.3 2.6 2.9 3.0 4.92 5.12 5.32 5.52 5.72 4.590 4.788 4.987 5.185 5.384 23 24 25 26 27 B B B B B 3/4 3/4 3/4 3/4 3/4 2 1/4 2 1/4 2 1/4 2 1/4 2 1/4 .343 .343 .343 .343 .343 1 1 1/16 1 1/16 1 1/16 1 1/16 21/32 23/32 23/32 23/32 23/32 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 3.3 3.5 3.6 3.7 3.8 50B28 50B29 50B30 50B31 50B32 5.92 6.12 6.32 6.52 6.72 5.582 5.781 5.979 6.178 6.376 28 29 30 31 32 B B B B B 3/4 3/4 3/4 3/4 3/4 2 1/4 2 1/4 2 1/4 2 1/4 2 1/4 .343 .343 .343 .343 .343 1 1/16 1 1/16 1 1/16 1 1/16 1 1/16 23/32 23/32 23/32 23/32 23/32 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 4.0 4.2 4.4 4.6 4.7 50B33 50B34 50B35 50B36 50B37 6.92 7.12 7.32 7.52 7.72 6.575 6.774 6.972 7.171 7.370 33 34 35 36 37 B 3/4 2 1/4 .343 B 3/4 2 1/4 .343 B 3/4 2 3/8 .343 B 3/4 2 3/8 .343 B 3/4 2 3/8 .343 LARGER SIZES ON NEXT PAGE 1 1/16 1 1/16 1 1/16 1 1/16 1 1/16 23/32 23/32 23/32 23/32 23/32 3 1/4 3 1/4 3 1/2 3 1/2 3 1/2 4.9 5.1 5.5 5.7 6.04 50B8 50B9 50B10 50B11 50B12 Outside 1.88” 2.09 2.30 2.50 2.70 Pitch 1.633” 1.827 2.023 2.219 2.415 50B13 50B14 50B15 50B16 50B17 2.91 3.11 3.32 3.52 3.72 50B18 50B19 50B20 50B21 50B22 H 1 13/64† 1 25/64† 1 19/32† 1 25/32† 1 63/64† .3 .4 .5 .6 .8 * Maximum bore shown is with standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. † Hub is recessed for chain clearance. These Type “B” Sprockets are made without keyways and setscrews. They are furnished with minimum bore which can be rebored to sized, keywayed and setscrewed for a reasonable extra charge. Roller Chain Sprockets Sprockets for 50 No. 50 , 5/8" Pitch ANSI Chain Steel Type "B" Minimum Bore Single Sprockets Table No. 1 DIAMETERS BORE DIMENSIONS T L P Stock Max.* Nom. Max. SMALLER SIZES ON PRECEDING PAGES B 3/4 2 3/8 .343 1 1/16 23/32 B 3/4 2 3/8 .343 1 1/16 23/32 B 3/4 2 3/8 .343 1 1/16 23/32 B 3/4 2 3/8 .343 1 1/16 23/32 B 3/4 2 3/8 .343 1 1/16 23/32 Part No. Outside Pitch No. Teeth H Wt. Lbs. 50B38 50B39 50B40 50B41 50B42 7.92 8.12 8.32 8.52 8.72 7.569 7.767 7.966 8.165 8.363 38 39 40 41 42 3 1/2 3 1/2 3 1/2 3 1/2 3 1/2 6.0 6.4 6.7 6.98 7.2 50B43 50B44 50B45 50B46 50B47 8.91 9.11 9.31 9.51 9.71 8.562 8.761 8.960 9.159 9.357 43 44 45 46 47 B B B B B 3/4 3/4 3/4 3/4 3/4 2 3/8 2 3/8 2 1/2 2 1/2 2 1/2 .343 .343 .343 .343 .343 1 1/16 1 1/16 1 1/16 1 1/16 1 1/16 23/32 23/32 23/32 23/32 23/32 3 1/2 3 1/2 3 3/4 3 3/4 3 3/4 7.49 7.7 8.2 8.6 8.88 50B48 50B49 50B50 50B51 50B52 9.91 10.11 10.31 10.51 10.71 9.556 9.755 9.954 10.153 10.351 48 49 50 51 52 B B B B B 3/4 3/4 3/4 3/4 3/4 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 .343 .343 .343 .343 .343 1 1/16 1 1/16 1 1/16 1 1/16 1 1/16 23/32 23/32 23/32 23/32 23/32 3 3/4 3 3/4 3 3/4 3 3/4 3 3/4 9.1 9.46 9.7 10.06 10.3 50B53 50B54 50B55 50B56 50B57 10.91 11.11 11.31 11.50 11.70 10.550 10.749 10.948 11.147 11.346 53 54 55 56 57 B B B B B 3/4 3/4 3/4 3/4 3/4 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 .343 .343 .343 .343 .343 1 1/16 1 1/16 1 1/16 1 1/16 1 1/16 23/32 23/32 23/32 23/32 23/32 3 3/4 3 3/4 3 3/4 3 3/4 3 3/4 10.7 10.9 11.4 11.7 12.0 50B58 50B59 50B60 50B70 50B72 50B76 11.90 12.10 12.30 14.29 14.69 15.49 11.544 11.743 11.942 13.931 14.329 15.124 58 59 60 70 72 76 B B B B B B 3/4 3/4 3/4 3/4 3/4 3/4 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 .343 .343 .343 .343 .343 .343 1 1/16 1 1/16 1 1/16 1 1/4 1 1/4 1 1/4 23/32 23/32 23/32 29/32 29/32 29/32 3 3/4 3 3/4 3 3/4 3 3/4 3 3/4 3 3/4 12.4 12.7 13.0 17.5 18.3 20.1 50B80 50B84 50B90 50B95 50B96 50B112 16.28 17.08 18.27 19.27 19.47 22.65 15.920 16.715 17.909 18.903 19.102 22.285 80 84 90 95 96 112 B B B B B B 3/4 3/4 3/4 3/4 3/4 3/4 3 1/8 3 1/8 3 1/8 3 1/8 3 1/8 3 1/8 .343 .343 .343 .343 .343 .343 1 5/8 1 5/8 1 5/8 1 5/8 1 5/8 1 5/8 1 9/32 1 9/32 1 9/32 1 9/32 1 9/32 1 9/32 4 5/8 4 5/8 4 5/8 4 5/8 4 5/8 4 5/8 25.2 27.2 30.3 33.1 33.7 43.8 Type * Maximum bore shown is with standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. † Hub is recessed for chain clearnce. These Type “B” Sprockets are furnished with no keyway and no setscrew. They are made with minimum bore which can be rebored to size, keywayed and setscrewed for a reasonable extra charge. Steel Double Sprockets with Browning Split Taper® Bushings HARDENED TEETH Table No. 2 DIAMETERS No. Type Outside Pitch Teeth DIMENSIONS M OL L P C H .332” .332 .332 .332 .332 Wt. Less Bushing 1.045” 2 5/16” 1 1/4” 1 3/32” 7/8” 2 1/2” 1.2 1.045 2 3/4 1 15/16 1 1/2 19/32 3 2.0 1.045 2 3/4 1 15/16 1 1/2 19/32 3 1.6 1.045 2 27/64 1 15/16 1 3/16 9/32 3 2.1 1.045 2 27/64 1 15/16 1 3/16 9/32 3 2.5 12 12 12 12 12 .332 .332 .332 .332 .332 1.045 1.045 1.045 1.045 1.045 2 3/16 2 3/16 2 3/16 2 3/16 2 3/16 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 29/32 29/32 29/32 29/32 29/32 0 0 0 0 0 3 3 3 3 3 2.0 2.5 2.8 3.2 3.6 24 25 26 27 28 12 12 12 12 12 .332 .332 .332 .332 .332 1.045 1.045 1.045 1.045 1.045 2 37/64 2 37/64 2 37/64 2 37/64 2 37/64 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1 11/32 1 11/32 1 11/32 1 11/32 1 11/32 3/32 3/32 3/32 3/32 3/32 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 4.0 4.5 5.3 5.9 6.3 5.979 6.376 6.972 7.171 7.966 30 32 35 36 40 12 12 12 12 12 .332 .332 .332 .332 .332 1.045 1.045 1.045 1.045 1.045 2 37/64 2 37/64 2 37/64 2 37/64 2 37/64 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1 11/32 1 11/32 1 11/32 1 11/32 1 11/32 3/32 3/32 3/32 3/32 3/32 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 7.5 8.5 10.4 11.0 13.6 8.72 9.31 9.91 8.363 8.960 9.556 42 45 48 12 .332 1.045 2 37/64 12 .332 1.045 2 37/64 12 .332 1.045 2 37/64 2 1/2 2 1/2 2 1/2 1 11/32 3/32 4 1/8 1 11/32 3/32 4 1/8 1 11/32 3/32 4 1/8 15.0 17.5 20.4 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 10.71 11.11 12.30 14.69 10.351 10.749 11.942 14.329 52 54 60 72 12 12 12 12 .332 .332 .332 .332 1.045 1.045 1.045 1.045 2 37/64 2 37/64 2 37/64 2 37/64 2 1/2 2 1/2 2 1/2 2 1/2 1 11/32 1 11/32 1 11/32 1 11/32 4 1/8 4 1/8 4 1/8 4 1/8 23.3 23.3 25.5 43.1 3/4-2 11/16 3/4-2 11/16 1 1/8-3 3/4 1 1/8-3 3/4 1 1/8-3 3/4 1 1/8-3 3/4 15.49 17.08 19.27 19.47 20.66 22.65 15.124 16.715 18.903 19.102 20.295 22.285 76 84 95 96 102 112 12 12 12 12 12 12 .332 .332 .332 .332 .332 .332 1.045 2 37/64 1.045 2 37/64 1.045 3 5/32 1.045 3 5/32 1.045 3 5/32 1.045 3 5/32 2 1/2 2 1/2 2 7/8 2 7/8 2 7/8 2 7/8 1 11/32 3/32 4 1/8 1 11/32 3/32 5 3/8 2 3/32 0 5 3/8 2 3/32 0 5 3/8 2 3/32 0 5 3/8 2 3/32 0 5 3/8 46.0 56.7 72.3 80.7 84.5 93.2 Part No. Bushing Bore Range D50H14 D50P15 D50P16 D50P17 D50P18 H P1 P1 P1 P1 3/8-1 1/2” 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 3.11” 2.809” 14 3.32 3.006 15 3.52 3.204 16 3.72 3.401 17 3.92 3.599 18 11 12 12 12 12 D50P19 D50P20 D50P21 D50P22 D50P23 P1 P1 P1 P1 P1 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 1/2-1 3/4 4.12 4.32 4.52 4.70 4.92 3.797 3.995 4.194 3.392 4.590 19 20 21 22 23 D50Q24 D50Q25 D50Q26 D50Q27 D50Q28 Q1 Q1 Q1 Q1 Q1 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 5.12 5.32 5.52 5.72 5.92 4.788 4.987 5.185 5.384 5.582 D50Q30 D50Q32 D50Q35 D50Q36 D50Q40 Q1 Q1 Q1 Q1 Q1 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 6.32 6.72 7.32 7.52 8.32 D50Q42 D50Q45 D50Q48 Q1 Q1 Q1 3/4-2 11/16 3/4-2 11/16 3/4-2 11/16 D50Q52 D50Q54 D50Q60 D50Q72 Q1 Q1 Q1 Q1 D50Q76 D50Q84 D50R95 D50R96 D50R102 D50R112 Q1 Q1 R1 R1 R1 R1 T 3/32 3/32 3/32 3/32 Standard Keyseats Table No. 3 Bore Range Keyseat 1/2" — 9/16" 5/8 — 7/8 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 3 3/8 — 3 3/4 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 7/8 x 7/16 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-26 Roller Chain Sprockets Steel Double Sprockets with Q-D® Bushings Table No. 1 Wt. Less Outside Pitch T M OL L P C H Bushing 1/2 - 2 5/8” 7.52” 7.171” QD-4 36 .332” 1.045” 2 11/32” 1 15/16” 13/16” 13/64” 3 7/8” 9.7 1/2 - 2 5/8 8.72 8.363 QD-4 42 .332 1.045 2 11/32 1 15/16 13/16 13/64 3 7/8 13.9 1/2 - 2 5/8 9.91 9.556 QD-4 48 .332 1.045 2 11/32 1 15/16 13/16 13/64 3 7/8 18.7 DIAMETERS Part No. Bushing D50SK36 D50SK42 D50SK48 SK SK SK D50SF52 D50SF54 D50SF60 D50SF68 D50SF72 SF SF SF SF SF 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 10.71 11.11 12.30 13.89 14.69 D50SF76 D50SF84 D50SF95 D50SF102 D50SF112 SF SF SF SF SF 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 15.49 17.08 19.27 20.66 22.65 Bore Range DIMENSIONS Type No. Teeth 10.351 10.749 11.942 13.533 14.329 QD-4 QD-4 QD-4 QD-4 QD-4 52 54 60 68 72 .332 .332 .332 .332 .332 1.045 1.045 1.045 1.045 1.045 2 15/32 2 15/32 2 15/32 2 15/32 2 15/32 2 1/16 2 1/16 2 1/16 2 1/16 2 1/16 7/8 7/8 7/8 7/8 7/8 13/64 13/64 13/64 13/64 13/64 4 5/8 4 5/8 4 5/8 4 5/8 4 5/8 22.1 24.0 30.1 39.4 44.4 15.124 16.715 18.903 20.295 22.285 QD-4 QD-4 QD-4 QD-4 QD-4 76 84 95 102 112 .332 .332 .332 .332 .332 1.045 1.045 1.045 1.045 1.045 2 15/32 2 15/32 2 15/32 2 15/32 2 15/32 2 1/16 2 1/16 2 1/16 2 1/16 2 1/16 7/8 7/8 7/8 7/8 7/8 13/64 13/64 13/64 13/64 13/64 4 5/8 4 5/8 4 5/8 4 5/8 4 5/8 49.8 61.4 79.2 91.7 111 Wt. Lbs. Steel Double Type "B" Minimum Bore Sprockets Table No. 2 DIAMETERS DB DB DB DB DB Stock 5/8” 5/8 5/8 5/8 3/4 Max.* 15/16” 1 1/8 1 5/16 1 3/8 1 1/2 T .332” .332 .332 .332 .332 DIMENSIONS L P H M Max. 1.045” 1 3/4” 45/64” 1 15/32” 1.045 1 3/4 45/64 1 11/16 1.045 1 3/4 45/64 1 7/8 1.045 1 3/4 45/64 2 1/16 1.045 1 3/4 45/64 2 5/16 16 17 18 19 20 DB DB DB DB DB 3/4 3/4 3/4 1 1 1 3/4 1 7/8 1 15/16 2 1/8 2 1/4 .332 .332 .332 .332 .332 1.045 1.045 1.045 1.045 1.045 1 3/4 1 3/4 1 3/4 1 3/4 1 3/4 45/64 45/64 45/64 45/64 45/64 2 1/2 2 11/16 2 15/16 3 1/8 3 1/4 2.8 3.2 3.8 4.1 4.5 4.194 4.392 4.590 4.788 4.987 21 22 23 24 25 DB DB DB DB DB 1 1 1 1 1 2 3/8 2 1/2 2 1/2 2 1/2 2 1/2 .332 .332 .332 .332 .332 1.045 1.045 1.045 1.045 1.045 1 3/4 1 7/8 1 7/8 1 7/8 1 7/8 45/64 53/64 53/64 53/64 53/64 3 1/2 3 5/8 3 5/8 3 5/8 3 3/4 5.2 5.6 6.0 6.4 7.1 5.52 6.32 6.72 7.32 7.52 5.185 5.979 5.384 6.972 7.171 26 30 32 35 36 DB DB DB DB DB 1 1 1 1 1 2 1/2 2 1/2 2 1/2 2 1/2 2 3/4 .332 .332 .332 .332 .332 1.045 1.045 1.045 1.045 1.045 1 7/8 1 7/8 1 7/8 1 7/8 2 1/8 53/64 53/64 53/64 53/64 1 5/64 3 3/4 3 3/4 3 3/4 3 3/4 4 1/4 7.4 9.5 10.6 12.6 15.0 D50B40 D50B42 D50B45 D50B48 8.32 8.72 9.31 9.91 7.966 8.363 8.960 9.556 40 42 45 48 DB DB DB DB 1 1 3/16 1 3/16 1 3/16 2 3/4 2 3/4 2 3/4 2 3/4 .332 .332 .332 .332 1.045 1.045 1.045 1.045 2 1/8 2 1/8 2 1/8 2 3/8 1 5/64 1 5/64 1 5/64 1 21/64 4 1/4 4 1/4 4 1/4 4 1/4 17.7 18.9 21.3 24.7 D50B52 D50B54 D50B60 D50B68 D50B72 D50B76 10.71 11.11 12.30 13.89 14.69 15.49 10.351 10.749 11.942 13.533 14.329 15.124 52 54 60 68 72 76 DB DB DB DB DB DB 1 3/16 1 3/16 1 5/16 1 5/16 1 5/16 1 5/16 2 3/4 2 3/4 3 3 1/4 3 1/4 3 1/4 .332 .332 .332 .332 .332 .332 1.045 1.045 1.045 1.045 1.045 1.045 2 3/8 2 3/8 2 3/8 2 3/8 2 3/8 2 3/8 1 21/64 1 21/64 1 21/64 1 21/64 1 21/64 1 21/64 4 1/4 4 1/4 4 1/2 4 3/4 4 3/4 4 3/4 28.4 30.4 36.9 46.8 51.9 57.2 D50B84 D50B95 D50B96 D50B102 D50B112 D50B120 17.08 19.27 19.47 20.66 22.65 24.24 16.715 18.903 19.102 20.295 22.285 23.876 84 95 96 102 112 120 DB DB DB DB DB DB 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 3 1/4 3 5/16 3 5/16 3 5/16 3 3/4 3 3/4 .332 .332 .332 .332 .332 .332 1.045 1.045 1.045 1.045 1.045 1.045 2 3/8 2 3/8 2 3/8 2 3/8 2 3/8 2 3/8 1 21/64 1 21/64 1 21/64 1 21/64 1 21/64 1 21/64 4 3/4 5 5 5 5 1/2 5 1/2 68.8 87.4 89.1 100 121 138 Part No. Hardened Teeth 50 D50B11 D50B12 D50B13 D50B14 D50B15 Outside 2.50” 2.71 2.91 3.11 3.32 Pitch 2.219” 2.415 2.612 2.809 3.006 D50B16 D50B17 D50B18 D50B19 D50B20 3.52 3.72 3.92 4.12 4.32 3.204 3.401 3.599 3.797 3.995 D50B21 D50B22 D50B23 D50B24 D50B25 4.52 4.72 4.92 5.12 5.32 D50B26 D50B30 D50B32 D50B35 D50B36 No. Teeth Type 11 12 13 14 15 BORE 1.0 1.1 1.4 1.9 2.4 * Maximum bore shown with standard keyway and setscrew over keyway. Slighly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. These type “B” sprockets are made without keyways or setscrews. They are furnished with a minimum bore which can be rebored to size and keywayed for a reasonable extra charge. Steel Triple Sprockets with Q-D® Bushings Table No. 3 H-27 36 42 48 DIMENSIONS OL L P T M Max. .332” 1.758 2 11/32” 1 15/16” 5/16” .332 1.758 2 11/32 1 15/16 5/16 .332 1.758 2 11/32 1 15/16 5/16 Wt. Less H Bushing 3 7/8” 14.6 3 7/8 21.5 3 7/8 29.6 1/2 - 2 15/16 10.71 10.351 QD-7 1/2 - 2 15/16 12.30 11.942 QD-7 1/2 - 2 15/16 14.69 14.329 QD-7 52 60 72 .332 .332 .332 1.758 2 15/32 2 1/16 1.758 2 15/32 2 1/16 1.758 2 15/32 2 1/16 3/8 3/8 3/8 4 5/8 4 5/8 4 5/8 34.4 47.9 71.8 1/2 - 2 15/16 17.08 16.715 QD-7 1/2 - 2 15/16 20.66 20.295 QD-7 84 102 .332 .332 1.758 2 15/32 2 1/16 1.758 2 15/32 2 1/16 3/8 3/8 4 5/8 4 5/8 100 151 Part No. Bushing Bore Range T50SK36 T50SK42 T50SK48 SK SK SK 1/2 - 2 5/8” 1/2 - 2 5/8 1/2 - 2 5/8 T50SF52 T50SF60 T50SF72 T50SF84 T50SF102 DIAMETERS Type No. Teeth QD-7 QD-7 QD-7 SF SF SF SF SF Outside 7.52” 8.72 9.91 Pitch 7.171 8.363 9.556 Roller Chain Sprockets Sprockets for No. 50 , 5/8" Pitch ANSI Chain Steel Triple Sprockets with Browning Split Taper® Bushings Table No. 1 HARDENED TEETH 50-60 DIAMETERS No. Type Outside Pitch Teeth T M 3.32” 3.006” 15 22 .332” 1.758” 3.52 3.204 16 22 .332 1.758 3.72 3.401 17 22 .332 1.758 3.92 3.599 18 22 .332 1.758 4.12 3.797 19 24 .332 1.758 DIMENSIONS Wt. Less H Bushing 3” 2.5 3 2.4 3 2.8 3 3.4 3 2.9 Part No. Bushing Bore Range T50P15 T50P16 T50P17 T50P18 T50P19 P2 P2 P2 P2 P1 3/4 - 1 3/4” 3/4 - 1 3/4 3/4 - 1 3/4 3/4 - 1 3/4 1/2 - 1 3/4 T50P20 T50P21 T50P23 T50Q24 P1 P1 P1 Q1 1/2 - 1 3/4 1/2 - 1 3/4 1/2 - 1 3/4 3/4 - 2 11/16 4.32 4.52 4.92 5.12 3.995 4.194 4.590 4.788 20 21 23 24 24 24 24 23 .332 .332 .332 .332 1.758 1.758 1.758 1.758 2 37/64 1 15/16 2 37/64 1 15/16 2 37/64 1 15/16 2 37/64 2 1/2 5/8 5/8 5/8 5/8 7/16 3 7/16 3 7/16 3 3/32 4 1/8 3.1 3.5 4.5 4.7 T50Q25 T50Q26 T50Q28 T50Q30 T50Q32 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 5.32 5.52 5.92 6.32 6.72 4.987 5.185 5.582 5.979 6.376 25 26 28 30 32 23 23 23 23 23 .332 .332 .332 .332 .332 1.758 1.758 1.758 1.758 1.758 2 37/64 2 37/64 2 37/64 2 37/64 2 37/64 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 5/8 5/8 5/8 5/8 5/8 3/32 3/32 3/32 3/32 3/32 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 5.0 5.9 7.3 8.8 10.9 T50Q35 T50Q36 T50Q40 T50Q42 T50Q48 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 7.32 7.52 8.32 8.72 9.91 6.972 7.171 7.966 8.363 9.556 35 36 40 42 48 23 23 23 23 23 .332 .332 .332 .332 .332 1.758 1.758 1.758 1.758 1.758 2 37/64 2 37/64 2 37/64 2 37/64 2 37/64 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 5/8 5/8 5/8 5/8 5/8 3/32 3/32 3/32 3/32 3/32 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 13.7 14.6 19.1 21.5 29.6 T50Q52 T50R60 T50R68 T50R72 Q1 R1 R1 R1 3/4 - 2 11/16 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 10.71 12.30 13.89 14.69 10.351 11.942 13.533 14.329 52 60 68 72 23 22 22 22 .332 .332 .332 .332 1.758 1.758 1.758 1.758 2 37/64 3 9/64 3 9/64 3 9/64 2 1/2 2 7/8 2 7/8 2 7/8 5/8 1 5/32 1 5/32 1 5/32 3/32 1/16 1/16 1/16 4 1/8 5 3/8 5 3/8 5 3/8 36.4 48.0 63.5 72.0 T50R76 T50R84 T50R95 T50R102 R1 R1 R1 R1 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 15.49 17.08 19.27 20.66 15.124 76 16.715 84 18.903 95 20.295 102 22 22 22 22 .332 .332 .332 .332 1.758 1.758 1.758 1.758 3 9/64 3 9/64 3 9/64 3 9/64 2 7/8 2 7/8 2 7/8 2 7/8 1 5/32 1 5/32 1 5/32 1 5/32 1/16 1/16 1/16 1/16 5 3/8 5 3/8 5 3/8 5 3/8 81.0 100 130 151 OL 3 7/16” 3 7/16 3 9/64 3 9/64 2 37/64 L P C 2 15/16” 1 15/32” 9/32” 2 15/16 1 15/32 9/32 2 15/16 1 3/16 0 2 15/16 1 3/16 0 1 15/16 5/8 7/16 Standard Keyseats Table No. 3 Bore Range Keyseat 3/8" — 7/16" 1/2 — 9/16 5/8 — 7/8 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 3 3/8 — 3 3/4 None 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 7/8 x 7/16 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-28 Roller Chain Sprockets Steel Single Sprockets with Browning Split Taper® Bushings HARDENED TEETH Table No. 1 H-29 60 DIAMETERS No. Type Outside Pitch Teeth 2.76” 2.427” 10 3 2.96 2.662 11 3 3.25 2.898 12 3 3.45 3.134 13 3 3.45 3.134 13 4 3.74 3.371 14 3 DIMENSIONS T OL L P Norm. .459” 1 3/4” 1” 1 3/32” .459 1 31/32 1 1/4 1 11/32 .459 1 13/16 1 1/4 1 3/16 .459 1 1/2 1 1/4 27/32 .459 2 5/16 1 15/16 1 21/32 .459 1 1/2 1 1/4 27/32 Wt. Less H Bushing 2” .6 2 1/2 .7 2 1/2 .8 2 1/2 .8 3 1.1 2 1/2 1.0 Part No. Bushing Bore Range H60G10 H60H11 H60H12 H60H13 H60P13 H60H14 G H H H P1 H 3/8 - 1” 3/8 - 1 1/2 3/8 - 1 1/2 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 H60P14 H60H15 H60P15 H60H16 H60P16 H60H17 P1 H P1 H P1 H 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 3.74 3.98 3.98 4.22 4.22 4.46 3.371 3.607 3.607 3.844 3.844 4.082 14 15 15 16 16 17 4 3 4 3 4 3 .459 .459 .459 .459 .459 .459 2 3/16 1 15/16 1 15/32 0 3 1 1/2 1 1/4 27/32 1/16 2 1/2 2 3/16 1 15/16 1 15/32 0 3 1 1/2 1 1/4 27/32 1/16 2 1/2 2 3/16 1 15/16 1 15/32 0 3 1 1/2 1 1/4 27/32 1/16 2 1/2 1.2 1.2 1.6 1.3 2.0 1.5 H60P17 H60H18 H60P18 H60H19 H60P19 H60H20 P1 H P1 H P1 H 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 1/2 - 1 3/4 3/8 - 1 1/2 4.46 4.70 4.70 4.95 4.95 5.19 4.082 4.319 4.319 4.557 4.557 4.794 17 18 18 19 19 20 4 3 4 3 4 3 .459 .459 .459 .459 .459 .459 2 3/16 1 15/16 1 15/32 0 3 1 1/2 1 1/4 27/32 1/16 2 1/2 2 3/16 1 15/16 1 15/32 0 3 1 1/2 1 1/4 27/32 1/16 2 1/2 2 3/16 1 15/16 1 15/32 0 3 1 1/2 1 1/4 27/32 1/16 2 1/2 2.2 1.7 2.4 1.9 2.5 2.1 H60P20 H60Q20 H60P21 H60Q21 H60H22 H60P22 P1 Q1 P1 Q1 H P1 1/2 - 1 3/4 3/4 - 2 11/16 1/2 - 1 3/4 3/4 - 2 11/16 3/8 - 1 1/2 1/2 - 1 3/4 5.19 5.19 5.43 5.43 5.67 5.67 4.794 4.794 5.032 5.032 5.270 5.270 20 20 21 21 22 22 4 4 4 4 3 4 .459 .459 .459 .459 .459 .459 2 3/16 1 15/16 1 15/32 0 3 2 25/32 2 1/2 2 1/32 0 4 1/8 2 3/16 1 15/16 1 15/32 0 3 2 25/32 2 1/2 2 1/32 0 4 1/8 1 1/2 1 1/4 27/32 1/16 2 1/2 2 3/16 1 15/16 1 15/32 0 3 3.0 3.5 3.0 3.8 2.6 3.3 H60Q22 H60P23 H60Q23 H60H24 H60P24 H60Q24 Q1 P1 Q1 H P1 Q1 3/4 - 2 11/16 1/2 - 1 3/4 3/4 - 2 11/16 3/8 - 1 1/2 1/2 - 1 3/4 3/4 - 2 11/16 5.67 5.91 5.91 6.15 6.15 6.15 5.270 5.508 5.508 5.746 5.746 5.746 22 23 23 24 24 24 4 4 4 3 4 4 .459 .459 .459 .459 .459 .459 2 25/32 2 1/2 2 3/16 1 15/16 2 25/32 2 1/2 1 1/2 1 1/4 2 3/16 1 15/16 2 25/32 2 1/2 4.1 3.5 4.3 3.0 3.9 4.5 H60P25 H60Q25 H60P26 H60Q26 H60P27 H60Q27 P1 Q1 P1 Q1 P1 Q1 1/2 - 1 3/4 3/4 - 2 11/16 1/2 - 1 3/4 3/4 - 2 11/16 1/2 - 1 3/4 3/4 - 2 11/16 6.39 6.39 6.63 6.63 6.87 6.87 5.984 5.984 6.222 6.222 6.460 6.460 25 25 26 26 27 27 4 4 4 4 4 4 .459 .459 .459 .459 .459 .459 2 3/16 1 15/16 1 15/32 2 25/32 2 1/2 2 1/32 2 3/16 1 15/16 1 15/32 2 25/32 2 1/2 2 1/32 2 3/16 1 15/16 1 15/32 2 25/32 2 1/2 2 1/32 0 0 0 0 0 0 3 4 1/8 3 4 1/8 3 4 1/8 4.3 4.0 4.3 6.4 4.6 6.6 H60P28 H60Q28 H60Q29 H60P30 H60Q30 60Q31 P1 Q1 Q1 P1 Q1 Q1 1/2 - 1 3/4 3/4 - 2 11/16 3/4 - 2 11/16 1/2 - 1 3/4 3/4 - 2 11/16 3/4 - 2 11/16 7.11 7.11 7.35 7.59 7.59 7.83 6.699 6.699 6.937 7.175 7.175 7.413 28 28 29 30 30 31 4 4 4 4 4 4 .459 .459 .459 .459 .459 .459 2 3/16 1 15/16 1 15/32 2 25/32 2 1/2 2 1/32 2 25/32 2 1/2 2 1/32 2 3/16 1 15/16 1 15/32 2 25/32 2 1/2 2 1/32 2 25/32 2 1/2 2 1/32 0 0 0 0 0 0 3 4 1/8 4 1/8 3 4 1/8 4 1/8 5.0 6.9 7.3 5.6 7.7 7.8 60Q32 60Q33 60Q34 60Q35 60Q36 60Q37 Q1 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 8.07 8.30 8.54 8.78 9.02 9.26 7.652 7.891 8.129 8.367 8.605 8.844 32 33 34 35 36 37 4 4 4 4 4 4 .459 .459 .459 .459 .459 .459 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/32 2 1/32 2 1/32 2 1/32 2 1/32 2 1/32 0 0 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 8.3 8.7 9.1 9.3 9.9 10.3 60Q38 60Q39 60Q40 60Q41 60Q42 60Q44 Q1 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 9.50 9.74 9.98 10.22 10.46 10.94 9.082 9.321 9.559 9.798 10.036 10.513 38 39 40 41 42 44 4 4 4 4 4 4 .459 .459 .459 .459 .459 .459 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/32 2 1/32 2 1/32 2 1/32 2 1/32 2 1/32 0 0 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 10.6 11.1 11.6 11.9 12.6 13.4 60Q45 60Q47 60Q48 60Q50 60Q54 60Q56 Q1 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 11.18 11.65 11.89 12.37 13.33 13.81 10.752 11.229 11.467 11.945 12.899 13.376 45 47 48 50 54 56 4 4 4 4 4 4 .459 .459 .459 .459 .459 .459 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/32 2 1/32 2 1/32 2 1/32 2 1/32 2 1/32 0 0 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 13.9 16.3 16.4 16.9 19.6 20.3 60Q60 60Q70 60R70 60Q72 60R72 60Q80 Q1 Q1 R1 Q1 R1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 1 1/8 - 3 3/4 3/4 - 2 11/16 1 1/8 - 3 3/4 3/4 - 2 11/16 14.73 17.12 17.12 17.63 17.63 19.54 14.331 16.717 16.717 17.194 17.194 19.103 60 70 70 72 72 80 4 4 4 4 4 4 .459 .459 .459 .459 .459 .459 2 25/32 2 25/32 3 5/32 2 25/32 3 5/32 2 25/32 2 1/2 2 1/2 2 7/8 2 1/2 2 7/8 2 1/2 2 1/32 2 1/32 2 13/32 2 1/32 2 13/32 2 1/32 0 0 0 0 0 0 5 3/8 4 1/8 5 3/8 4 1/8 5 3/8 4 1/8 22.9 30.9 31.8 31.9 34.1 39.1 60R80 60Q84 60R84 60Q96 60R96 60Q112 60R112 R1 Q1 R1 Q1 R1 Q1 R1 1 1/8 - 3 3/4 3/4 - 2 11/16 1 1/8 - 3 3/4 3/4 - 2 11/16 1 1/8 - 3 3/4 3/4 - 2 11/16 1 1/8 - 3 3/4 19.54 20.49 20.49 23.36 23.36 27.18 27.18 19.103 80 20.058 84 20.058 84 22.922 96 22.922 96 26.742 112 26.742 112 4 4 4 4 4 4 4 .459 .459 .459 .459 .459 .459 .459 3 5/32 2 25/32 3 5/32 2 25/32 3 5/32 2 25/32 3 5/32 2 7/8 2 1/2 2 7/8 2 1/2 2 7/8 2 1/2 2 7/8 2 13/32 2 1/32 2 13/32 2 1/32 2 13/32 2 1/32 2 13/32 0 0 0 0 0 0 0 5 3/8 4 1/8 5 3/8 4 1/8 5 3/8 4 1/8 5 3/8 41.5 41.6 44.8 54.0 56.0 73.0 74.5 C 9/16” 9/16 13/32 1/16 5/32 1/16 2 1/32 0 4 1/8 1 15/32 0 3 2 1/32 0 4 1/8 27/32 1/16 2 1/2 1 15/32 0 3 2 1/32 0 4 1/8 Where two sprockets with the same number of teeth but different bushings are offered, we suggest using the one with the larger bushing for heavier service drives. Roller Chain Sprockets Sprockets for No. 60 , 3/4" Pitch ANSI Chain Steel Single Sprockets with Q-D® Bushings Table No. 1 HARDENED TEETH 60 DIAMETERS Part No. Bushing Bore Range H60JA11* H60JA12 H60JA13 H60SH14 H60SH15 JA JA JA SH SH 1/2 - 1 1/4” 1/2 - 1 1/4 1/2 - 1 1/4 1/2- 1 5/8 1/2- 1 5/8 Outside 3.00” 3.25 3.49 3.74 3.98 Pitch 2.662” 2.898 3.134 3.371 3.607 QD-1 QD-1 QD-1 QD-1 QD-1 H60SH16 H60SDS17 H60SDS18 H60SDS19 H60SDS20 SH SDS SDS SDS SDS 1/2- 1 5/8 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 4.22 4.46 4.70 4.95 5.19 3.844 4.082 4.319 4.557 4.794 QD-1 QD-1 QD-1 QD-1 QD-1 16 17 18 19 20 H60SDS21 H60SDS22 H60SDS23 H60SDS24 H60SDS25 SDS SDS SDS SDS SDS 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 5.43 5.67 5.91 6.15 6.39 5.032 5.270 5.508 5.746 5.984 QD-1 QD-1 QD-1 QD-1 QD-1 H60SK26 H60SK27 H60SK28 H60SK30 60SK32 SK SK SK SK SK 1/2 - 2 5/8 1/2 - 2 5/8 1/2 - 2 5/8 1/2 - 2 5/8 1/2 - 2 5/8 6.63 6.87 7.11 7.59 8.07 6.222 6.460 6.699 7.175 7.652 60SK35 60SK36 60SK40 60SF42 60SF45 SK SK SK SF SF 1/2 - 2 5/8 1/2 - 2 5/8 1/2 - 2 5/8 1/2 - 2 15/16 1/2 - 2 15/16 8.78 9.02 9.98 10.46 11.18 60SF48 60SF54 60SF60 60SF70 60SF72 SF SF SF SF SF 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 60SF80 60SF84 60SF96 SF SF SF 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 Type No. Teeth T Norm. 11 .459” 12 .459 13 .459 14 .459 15 .459 DIMENSIONS Wt. Less H Bushing 2” .54 2 .74 2 .89 2 11/16 1.04 2 11/16 1.30 OL 1 5/16” 1 5/16 1 5/16 1 23/32 1 23/32 L 1” 1 1 1 5/16 1 5/16 P 45/64” 45/64 45/64 1 3/64 1 3/64 .459 .459 .459 .459 .459 1 23/32 1 21/32 1 21/32 1 21/32 1 21/32 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 1 3/64 2 11/16 63/64 3 1/8 63/64 3 1/8 63/64 3 1/8 63/64 3 1/8 1.57 1.57 1.78 2.01 2.23 21 22 23 24 25 .459 .459 .459 .459 .459 1 21/32 1 21/32 1 21/32 1 21/32 1 21/32 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 63/64 63/64 63/64 63/64 63/64 3 1/8 3 1/8 3 1/8 3 1/8 3 1/8 2.45 2.69 2.94 3.20 3.47 QD-1 QD-1 QD-1 QD-1 QD-1 26 27 28 30 32 .459 .459 .459 .459 .459 2 11/32 2 11/32 2 11/32 2 11/32 2 11/32 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 1 39/64 1 39/64 1 39/64 1 39/64 1 39/64 3 7/8 3 7/8 3 7/8 3 7/8 3 7/8 4.53 4.82 5.1 5.8 6.5 8.367 8.605 9.559 10.036 10.752 QD-1 QD-1 QD-1 QD-1 QD-1 35 36 40 42 45 .459 .459 .459 .459 .459 2 11/32 1 15/16 1 39/64 2 11/32 1 15/16 1 39/64 2 11/32 1 15/16 1 39/64 2 15/32 2 1/16 1 43/64 2 15/32 2 1/16 1 43/64 3 7/8 3 7/8 3 7/8 4 5/8 4 5/8 7.6 8.0 9.7 11.4 12.9 11.89 13.33 14.76 17.15 17.63 11.467 12.899 14.331 16.717 17.194 QD-1 QD-1 QD-1 QD-1 QD-1 48 54 60 70 72 .459 .459 .459 .459 .459 2 15/32 2 15/32 2 15/32 2 15/32 2 15/32 2 1/16 2 1/16 2 1/16 2 1/16 2 1/16 1 43/64 1 43/64 1 43/64 1 43/64 1 43/64 4 5/8 4 5/8 4 5/8 4 5/8 4 5/8 14.5 17.4 21.2 28.4 30.0 19.54 20.49 23.36 19.103 QD-1 20.058 QD-1 22.922 QD-1 80 84 96 .459 .459 .459 2 15/32 2 15/32 2 15/32 2 1/16 1 43/64 2 1/16 1 43/64 2 1/16 1 43/64 4 5/8 4 5/8 4 5/8 36.8 40.4 52.4 * Bushing mounts with capscrews on “A” side only. Standard Keyseats Table No. 2 Bore Range Keyseat 3/8" — 7/16" 1/2 — 9/16 5/8 — 7/8 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 3 3/8 — 3 3/4 None 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 7/8 x 7/16 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-30 Roller Chain Sprockets Steel Finished Bore Single Sprockets Table No. 1 HARDENED TEETH Part No. H609 H6010 H6011 H6012 H6013 H6014 H6015 H6016 H6017 H6018 H6019 H6020 H6021 H6022 H6023 H6024 H6025 H6026 H6027 H6028 H6029 H6030 6032 6035 6036 6040 6045 6046 6076 60 DIAMETERS No. Type Outside Pitch Teeth 2.50” 2.193” 9 1 2.76 2.427 10 1 2.96 2.662 11 1 3.25 2.898 12 1 3.45 3.134 13 1 3.74 3.371 14 1 3.98 3.607 15 1 4.22 3.844 16 1 4.46 4.082 17 1 4.70 4.319 18 1 4.95 4.557 19 1 5.19 4.794 20 1 5.43 5.032 21 1 5.67 5.270 22 1 5.91 5.508 23 1 6.15 5.746 24 1 6.39 5.984 25 1 6.63 6.222 26 1 6.87 6.460 27 1 7.11 6.699 28 1 7.35 6.937 29 1 7.59 7.175 30 1 8.07 7.652 32 1 8.78 8.367 35 1 9.02 8.605 36 1 9.98 9.559 40 1 11.18 10.752 45 1 11.42 10.990 46 1 18.55 18.149 76 1 STOCK BORES MARKED "X" 3/4” x x x x x x x x - 7/8” x x x x x x x x - 1” x x x x x x x x x x x x x x x x x x x x x x x x x x x - 1 1/8” 1 3/16” 1 1/4” 1 3/8” 1 7/16” 1 1/2” 1 5/8” 1 3/4” 1 15/16” x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x DIMENSIONS T L P Nom. .459” 1 3/16” 47/64” .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 3/16 47/64 .459 1 13/16 1 23/64 Wt. Lbs. .6 .8 1.0 1.3 1.5 1.7 2.0 2.5 2.7 3.4 4.1 3.9 5.4 5.7 6.0 6.3 6.5 6.8 7.1 7.4 7.4 8.0 8.6 9.5 9.9 11.5 13.8 14.2 33.7 All Stock Finished Bore Sprockets are furnished with Standard Keyway on Centerline of Toothe and Hallow Head Setscrew over Keyway. Sprockets with HARDENED TEETH have an additional Setscrew at 90° to Keyway. Type "A" Steel Plate Sprockets Table No. 2 H-31 Part No. Outside Dia. Pitch Dia. No. Teeth Stock Bore T (Nom.) Wt. Lbs. Part No. Outside Dia. Pitch Dia. No. Teeth Stock Bore T (Nom.) Wt. Lbs. 60A10 60A11 60A12 60A13 60A14 2.76” 3.00 3.25 3.45 3.74 2.427” 2.662 3.134 3.134 3.371 10 11 12 13 14 5/8” 5/8 5/8 5/8 5/8 .459” .459 .459 .459 .459 .4 .5 .6 .7 .9 60A42 60A43 60A44 60A45 60A46 10.46” 10.70 10.94 11.18 11.42 10.036” 10.275 10.513 10.752 10.990 42 43 44 45 46 3/4” 3/4 3/4 3/4 3/4 .459” .459 .459 .459 .459 9.9 10.1 10.6 11.3 11.8 60A15 60A16 60A17 60A18 60A19 3.98 4.22 4.46 4.70 4.95 3.607 3.844 4.082 4.319 4.557 15 16 17 18 19 5/8 5/8 5/8 5/8 3/4 .459 .459 .459 .459 .459 1.0 1.1 1.3 1.5 1.8 60A47 60A48 60A49 60A50 60A51 11.65 11.89 12.13 12.37 12.61 11.229 11.467 11.706 11.945 12.183 47 48 49 50 51 3/4 3/4 3/4 3/4 3/4 .459 .459 .459 .459 .459 12.3 12.6 13.2 13.8 14.4 60A20 60A21 60A22 60A23 60A24 5.19 5.43 5.67 5.91 6.15 4.794 5.032 5.270 5.508 5.746 20 21 22 23 24 3/4 3/4 3/4 3/4 3/4 .459 .459 .459 .459 .459 1.9 2.2 2.4 2.6 2.8 60A52 60A53 60A54 60A55 60A56 12.85 13.09 13.33 13.57 13.81 12.422 12.660 12.899 13.137 13.376 52 53 54 55 56 3/4 3/4 3/4 3/4 3/4 .459 .459 .459 .459 .459 15.0 15.5 16.1 16.7 17.3 60A25 60A26 60A27 60A28 60A29 6.39 6.53 6.87 7.11 7.35 5.984 6.222 6.460 6.699 6.937 25 26 27 28 29 3/4 3/4 3/4 3/4 3/4 .459 .459 .459 .459 .459 3.3 3.6 4.0 4.3 4.5 60A57 60A58 60A59 60A60 60A64 14.04 14.28 14.52 14.76 15.72 13.615 13.853 14.092 14.331 15.285 57 58 59 60 64 3/4 3/4 3/4 3/4 3/4 .459 .459 .459 .459 .459 18.0 18.6 19.3 19.9 22.7 60A30 60A31 60A32 60A33 60A34 60A35 7.59 7.83 8.07 8.30 8.54 8.78 7.175 7.413 7.652 7.890 8.129 8.367 30 31 32 33 34 35 3/4 3/4 3/4 3/4 3/4 3/4 .459 .459 .459 .459 .459 .459 4.9 5.3 5.6 6.0 6.5 7.0 60A65 60A66 60A68 60A70 60A72 60A76 15.93 16.16 16.67 17.15 17.63 18.55 15.524 15.762 16.240 16.717 17.194 18.149 65 66 68 70 72 76 3/4 3/4 3/4 3/4 3/4 1 .459 .459 .459 .459 .459 .459 23.4 24.1 25.6 27.1 28.7 33.9 60A36 60A37 60A38 60A39 60A40 60A41 9.02 9.26 9.50 9.74 9.98 10.22 8.605 8.844 9.082 9.321 9.559 9.798 36 37 38 39 40 41 3/4 3/4 3/4 3/4 3/4 3/4 .459 .459 .459 .459 .459 .459 7.3 7.8 8.2 8.3 9.0 9.4 60A80 60A84 60A90 60A96 60A112 19.54 20.49 21.93 23.36 27.18 19.103 20.058 21.490 22.922 26.742 80 84 90 96 112 1 1 1 1 1 .459 .459 .459 .459 .459 37.3 39.9 44.9 52.4 68.5 Roller Chain Sprockets Sprockets for No. 60 , 3/4" Pitch ANSI Chain Steel Single Type "B" Minimum Bore Single Sprockets Table No. 1 Max.* 13/16” 15/16 1 3 /16 1 5/16 1 3/8 T Nom. .459” .459 .459 .459 .459 DIMENSIONS L P H Max. 1 1/4” 51/64” 1 15/32”† 1 1/4 51/64 1 11/16† 1 1/4 51/64 1 15/16† 1 1/4 51/64 2 5/32† 1 1/4 51/64 2 25/64† Wt. Lbs. B B B B B Stock 5/8” 3/4 3/4 3/4 34 13 14 15 16 17 B B B B B 3/4 3/4 3/4 3/4 3/4 1 1/2 1 3/4 1 7/8 2 2 1/4 .459 .459 .459 .459 .459 1 1/4 1 3/16 1 3/16 1 3/16 1 3/16 51/64 47/64 47/64 47/64 47/64 2 41/64† 2 9/16 2 7/8 3 1/16 3 3/8 1.7 2.0 2.4 2.8 3.2 4.319 4.557 4.794 5.032 5.270 18 19 20 21 22 B B B B B 3/4 3/4 3/4 34 3/4 2 3/8 2 3/8 2 5/8 2 5/8 2 5/8 .459 .459 .459 .459 .459 1 3/16 1 3/16 1 3/16 1 3/16 1 3/16 47/64 47/64 47/64 47/64 47/64 3 1/2 3 1/2 3 7/8 3 7/8 3 7/8 3.9 4.2 4.6 4.8 5.1 5.91 6.15 6.39 6.63 6.87 5.508 5.746 5.984 6.222 6.460 23 24 25 26 27 B B B B B 3/4 3/4 3/4 3/4 3/4 2 5/8 2 5/8 2 3/4 2 3/4 2 3/4 .459 .459 .459 .459 .459 1 3/16 1 3/16 1 3/16 1 3/16 1 3/16 47/64 47/64 47/64 47/64 47/64 3 7/8 4 4 4 4 5.3 5.6 6.1 6.4 6.7 60B28 60B29 60B30 60B31 60B32 7.11 7.35 7.59 7.83 8.07 6.699 6.937 7.175 7.413 7.652 28 29 30 31 32 B B B B B 3/4 3/4 34 3/4 3/4 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 .459 .459 .459 .459 .459 1 3/16 1 3/16 1 3/16 1 3/16 1 3/16 47/64 47/64 47/64 47/64 47/64 4 4 4 4 4 7.0 7.4 7.7 8.0 8.4 60B33 60B34 60B35 60B36 60B37 8.30 8.54 8.78 9.02 9.26 7.890 8.129 8.367 8.605 8.844 33 34 35 36 37 B B B B B 3/4 3/4 3/4 3/4 3/4 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 .459 .459 .459 .459 .459 1 3/16 1 3/16 1 3/16 1 3/16 1 3/16 47/64 47/64 47/64 47/64 47/64 4 4 4 4 4 8.8 9.2 9.6 10.0 10.4 60B38 60B39 60B40 60B41 60B42 9.50 9.74 9.98 10.22 10.46 9.082 9.321 9.559 9.798 10.036 38 39 40 41 42 B B B B B 3/4 34 3/4 3/4 3/4 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 .459 .459 .459 .459 .459 1 3/16 1 3/16 1 3/16 1 3/16 1 3/16 47/64 47/64 47/64 47/64 47/64 4 1/4 4 1/4 4 1/4 4 1/4 4 1/4 11.2 11.6 12.1 12.6 13.1 60B43 60B44 60B45 60B46 60B47 10.70 10.94 11.18 11.42 11.65 10.275 10.513 10.752 10.990 11.229 43 44 45 46 47 B B B B B 3/4 3/4 3/4 3/4 3/4 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 .459 .459 .459 .459 .459 1 3/16 1 3/16 1 3/16 13/16 1 3/16 47/64 47/64 47/64 47/64 47/64 4 1/4 4 1/4 4 1/4 4 1/4 4 1/4 13.6 14.1 14.6 15.2 15.6 60B48 60B49 60B50 60B51 60B52 11.89 12.13 12.37 12.61 12.85 11.467 11.706 11.945 12.183 12.422 48 49 50 51 52 B B B B B 3/4 3/4 3/4 3/4 3/4 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 .459 .459 .459 .459 .459 1 3/16 13/16 1 3/16 1 3/16 1 3/16 47/64 47/64 47/64 47/64 47/64 4 1/4 4 1/4 4 1/4 4 1/4 4 1/4 16.2 16.8 17.3 18.0 18.6 60B53 60B54 60B56 60B57 13.09 13.33 13.81 14.04 12.660 12.899 13.376 13.615 53 54 56 57 B B B B 3/4 34 3/4 3/4 2 3/4 2 3/4 3 1/8 3 1/8 .459 .459 .459 .459 1 3/16 1 3/16 1 3/4 1 3/4 47/64 47/64 1 19/64 1 19/64 4 1/4 4 1/4 4 5/8 4 5/8 19.2 19.8 24.2 24.95 60B58 60B60 60B64 60B65 14.28 14.76 15.72 15.96 13.853 14.331 15.285 15.524 58 60 64 65 B B B B 3/4 3/4 3/4 3/4 3 1/8 3 1/8 3 1/8 3 1/8 .459 .459 .459 .459 1 3/4 1 3/4 1 3/4 1 3/4 19/64 19/64 19/64 19/64 4 5/8 4 5/8 4 5/8 4 5/8 25.6 26.9 29.8 30.5 60B68 60B70 60B72 60B76 60B80 16.67 17.15 17.63 18.58 19.54 16.240 16.717 17.194 18.149 19.103 68 70 72 76 80 B B B B B 3/4 3/4 3/4 1 1 3 1/8 3 1/8 3 1/8 3 1/4 3 1/4 .459 .459 .459 .459 .459 1 3/4 1 3/4 1 3/4 1 13/16 1 13/16 19/64 19/64 19/64 1 23/64 1 23/64 4 5/8 4 5/8 4 5/8 4 3/4 4 3/4 32.8 34.4 36.1 40.0 43.6 60B84 60B90 60B96 60B112 20.49 21.93 23.36 27.18 20.058 21.490 22.922 26.742 84 90 96 112 B B B B 1 1 1 1 3 1/4 4 4 4 .459 .459 .459 .459 1 13/16 2 1/8 2 1/8 2 1/8 1 23/64 1 43/64 1 43/64 1 43/64 4 3/4 6 6 6 47.4 60.0 66.5 85.8 Part No. 60 DIAMETERS No. Teeth Type 8 9 10 11 12 3.134 3.371 3.607 3.844 4.082 4.70 4.95 5.19 5.43 5.67 60B23 60B24 60B25 60B26 60B27 60B8 60B9 60B10 60B11 60B12 Outside 2.26” 2.50 2.76 2.96 3.25 Pitch 1.960” 2.193 2.427 2.662 2.898 60B13 60B14 60B15 60B16 60B17 3.45 3.75 3.98 4.22 4.46 60B18 60B19 60B20 60B21 60B22 BORE * Maximum bore shown is with standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. † Hub is recessed for chain clearance. These type “B” Sprockets are furnished with no keyway and no setscrew. They are made with minimum bore which can be rebored to size, keywayed an setscrewed for a reasonable extra charge. .5 .6 .9 1.0 1.3 Standard Keyseats Table No. 3 Bore Range Keyseat 1/2" — 9/16" 5/8 — 7/8 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 3 3/8 — 3 3/4 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 7/8 x 7/16 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-32 Roller Chain Sprockets Steel Double Sprockets with Q-D® Bushings Table No. 1 DIAMETERS Part Bore Bushing No. Range Outside Pitch D60SH14* SH 1/2 - 1 5/8” 3.74” 3.371 D60SDS22 SDS 1/2 - 2 5.67 5.270 D60SF36 SF 1/2 - 2 15/16 9.02 8.602 D60E42 E 7/8 - 3 1/2 10.46 10.036 D60E45 E 7/8 - 3 1/2 11.18 10.752 D60E52 D60E60 D60E68 D60E76 D60E95 60 E E E E E 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 12.85 14.76 16.67 18.58 23.12 12.422 14.331 16.240 18.149 22.683 No. Teeth T QD-5 14 .444” QD-6 22 .444 QD-6 36 .444 QD-4 42 .444 QD-4 45 .444 DIMENSIONS Wt. Less Bushing M OL Max L P C H 1.341” 2 1/4” 1 7/32” 11/16” - 2 11/16” 1.87 1.341 1 21/32 1 5/16 3/32 3 1/8 5.3 1.341 2 15/32 2 1/16 25/32 4 5/8 17.6 1.341 3 1/4 2 3/4 1 3/16 9/32” 6 25.6 1.341 3 1/4 2 3/4 1 3/16 9/32 6 29.9 QD-4 QD-4 QD-4 QD-4 QD-4 1.341 1.341 1.341 1.341 1.341 Type 52 60 68 76 95 .444 .444 .444 .444 .444 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 1 3/16 1 3/16 1 3/16 1 3/16 1 3/16 9/32 9/32 9/32 9/32 9/32 6 6 6 6 6 41.2 56.1 73.1 92.4 147 * Bushing mounts with capscrews on "A" side only. Steel Double Sprockets with Q-D® Bushings Table No. 2 HARDENED TEETH DIAMETERS No. DIMENSIONS Part Bore Wt. Less Bushing Type No. Range Outside Pitch Teeth T M OL L P C H Bushing D60P13 P1 1/2 - 1 3/4” 3.45” 3.134” 13 12 .444” 1.341” 3 1/8” 1 15/16” 1 19/32” 63/64” 3” 2.5 D60P14 P1 1/2 - 1 3/4 3.74 3.371 14 12 .444 1.341 3 1 15/16 1 13/32 13/16 3 2.3 D60P15 P1 1/2 - 1 3/4 3.98 3.607 15 12 .444 1.341 3 1 15/16 1 13/32 13/16 3 2.7 D60P16 P1 1/2 - 1 3/4 4.22 3.844 16 13 .444 1.341 2 7/32 1 15/16 5/8 1/32 3 2.4 D60P17 P1 1/2 - 1 3/4 4.46 4.082 17 13 .444 1.341 2 7/32 1 15/16 5/8 1/32 3 2.8 D60P18 D60P19 D60P20 D60Q21 D60Q22 P1 P1 P1 Q1 Q1 1/2 - 1 3/4 1/2 - 1 3/4 1/2 - 1 3/4 3/4 - 2 11/16 3/4 - 2 11/16 4.70 4.95 5.19 5.43 5.67 4.319 4.557 4.794 5.032 5.270 18 19 20 21 22 13 13 13 12 12 .444 .444 .444 .444 .444 1.341 1.341 1.341 1.341 1.341 2 7/32 1 15/16 5/8 2 7/32 1 15/16 5/8 2 7/32 1 15/16 5/8 2 25/32 2 1/2 1 5/32 2 25/32 2 1/2 1 5/32 D60Q23 D60Q24 D60Q25 D60Q26 D60Q27 D60Q28 Q1 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 5.91 6.15 6.39 6.63 6.87 7.11 5.508 5.746 5.984 6.222 6.460 6.699 23 24 25 26 27 28 12 12 12 12 12 12 .444 .444 .444 .444 .444 .444 1.341 1.341 1.341 1.341 1.341 1.341 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1 5/32 1 5/32 1 5/32 1 5/32 1 5/32 1 5/32 0 0 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 6.3 7.0 7.9 8.8 9.6 10.5 D60Q30 D60Q32 D60Q35 D60Q36 D60Q40 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 7.59 8.07 8.78 9.02 9.98 7.175 7.652 8.367 8.605 9.559 30 32 35 36 40 12 12 12 12 12 .444 .444 .444 .444 .444 1.341 1.341 1.341 1.341 1.341 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1 5/32 1 5/32 1 5/32 1 5/32 1 5/32 0 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 12.3 14.3 17.7 18.4 23.9 D60Q42 D60R42 D60R45 D60R48 Q1 R1 R1 R1 3/4 - 2 11/16 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 10.46 10.46 11.18 11.89 10.036 10.036 10.752 11.467 42 42 45 48 12 12 12 12 .444 .444 .444 .444 1.341 1.341 1.341 1.341 2 25/32 3 5/32 3 5/32 3 5/32 2 1/2 2 7/8 2 7/8 2 7/8 1 5/32 1 17/32 1 17/32 1 17/32 0 0 0 0 4 1/8 5 3/8 5 3/8 5 3/8 26.3 25.7 30.2 35.1 D60R52 D60R54 D60R60 D60R68 R1 R1 R1 R1 1 1/8 - 3 3/4 12.85 12.422 1 1/8 - 3 3/4 13.33 12.899 1 1/8 - 3 3/4 14.76 14.331 1 1/8 - 3 3/4 16.67 16.240 52 54 60 68 12 12 12 12 .444 .444 .444 .444 1.341 1.341 1.341 1.341 3 5/32 3 5/32 3 5/32 3 5/32 2 7/8 2 7/8 2 7/8 2 7/8 1 17/32 1 17/32 1 17/32 1 17/32 0 0 0 0 5 3/8 5 3/8 5 3/8 5 3/8 41.8 45.1 54.8 73.8 D60R72 D60R76 D60R84 D60R95 D60R96 R1 R1 R1 R1 R1 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 72 76 84 95 96 12 12 12 12 12 .444 .444 .444 .444 .444 1.341 1.341 1.341 1.341 1.341 3 5/32 3 5/32 3 5/32 3 5/32 3 5/32 2 7/8 2 7/8 2 7/8 2 7/8 2 7/8 1 17/32 1 17/32 1 17/32 1 17/32 1 17/32 0 0 0 0 0 5 3/8 5 3/8 5 3/8 5 3/8 5 3/8 81.8 93.0 111 148 155 T .444” .444 .444 .444 .444 DIMENSIONS M L Max. P H 1.341” 2 1/8” 25/32” 1 13/16” 1.341 2 1/8 25/32 2 1/8 1.341 2 1/8 25/32 2 1/4 1.341 2 1/8 25/32 2 1/2 1.341 2 1/8 25/32 2 13/16 Wt. Lbs. 1.5 2.1 2.5 3.1 4.0 DIAMETERS Part No. Outside Pitch D60B11 3.00” 2.662” D60B12 3.25 2.898 D60B13 3.45 3.134 D60B14 3.74 3.371 D60B15 3.98 3.607 HARDENED TEETH 17.194 18.149 20.058 22.683 22.922 3.4 4.0 4.7 4.8 5.6 Steel Double Type "B" and "C" Minimum Bore Sprockets Table No. 3 H-33 17.63 18.58 20.49 23.12 23.36 1/32 3 1/32 3 1/32 3 0 4 1/8 0 4 1/8 No. Teeth 11 12 13 14 15 Type DB DB DB DB DB BORE Stock Max.* 1” 1 1/4” 1 1 7/16 1 1 1/2 1 1 3/4 1 1 7/8 D60B16 D60B17 D60B18 D60B19 D60B20 4.22 4.46 4.70 4.95 5.19 3.844 4.082 4.319 4.557 4.794 16 17 18 19 20 DB DB DB DB DB 1 1 1 1 1 2 2 1/4 2 3/8 2 1/2 2 1/2 .444 .444 .444 .444 .444 1.341 1.341 1.341 1.341 1.341 2 1/8 2 1/8 2 1/8 2 1/8 2 1/8 25/32 25/32 25/32 25/32 25/32 3 3 1/4 3 1/2 3 11/16 3 3/4 4.9 5.7 6.5 6.8 7.7 D60B21 D60B22 D60B23 D60B24 D60B25 5.43 5.67 5.91 6.15 6.39 5.032 5.270 5.508 5.746 5.984 21 22 23 24 25 DB DB DB DB DB 1 1 1 1 1 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 .444 .444 .444 .444 .444 1.341 1.341 1.341 1.341 1.341 2 1/8 2 1/8 2 1/8 2 1/8 2 1/8 25/32 25/32 25/32 25/32 25/32 4 1/8 4 1/4 4 1/4 4 1/4 4 1/4 9.3 9.8 10.5 11.2 11.8 D60B26 D60B30 D60B32 D60B35 D60B36 D60B40 6.63 7.59 8.07 8.78 9.02 9.98 6.222 7.175 7.652 8.367 8.605 9.559 26 30 32 35 36 40 DB DB DB DB DB DB 1 1 1 1 1 1 2 3/4 2 3/4 3 3 3 5/16 3 1/2 .444 .444 .444 .444 .444 .444 1.341 1.341 1.341 1.341 1.341 1.341 2 1/8 2 1/8 2 3/8 2 3/8 2 3/8 2 3/4 25/32 25/32 1 1/32 1 1/32 1 1/32 1 1/32 4 1/4 4 1/4 4 1/4 4 1/4 5 5 1/4 12.8 16.6 20.4 23.7 25.9 33.8 *Maximum bore shown is with standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. These type “B” and “C” sprockets are made without keyways or setscrews. They are furnished with a minimum bore which can be rebored to size and keywayed for a reasonable extra charge Roller Chain Sprockets Sprockets for No. 60 , 3/4" Pitch ANSI Chain Table No. 1 Steel Double Type "B" and "C" Minimum Bore Sprockets Part DIAMETERS BORE DIMENSIONS No. Type Teeth Outside Pitch Stock Max.* T M L Max. P No. D60B42 10.46 10.036 42 DB 1 3 1/2 .444 1.341 2 3/4 1 1/32 D60B45 11.18 10.752 45 DB 1 1/4 3 1/2 .444 1.341 2 3/4 1 1/32 D60B52 12.85 12.422 52 DB 1 1/4 3 1/2 .444 1.341 2 3/4 1 1/32 D60B60 14.76 14.331 60 DB 1 1/4 3 1/2 .444 1.341 2 3/4 1 1/32 D60C68 D60C72 D60C76 D60C95 16.67 17.63 18.58 23.12 60-80 16.240 17.194 18.149 22.683 68 72 76 95 DC DC DC DC 1 1/4 1 1/4 1 1/4 1 11/16 3 1/2 3 3/4 3 3/4 3 3/4 .444 .444 .444 .444 1.341 1.341 1.341 1.341 3 3 3 3 1/2 53/64 53/64 53/64 1 5/64 H 5 1/4 5 1/4 5 1/4 5 1/4 Wt. Lbs. 36.5 40.5 51.7 66.6 5 1/4 5 1/2 5 1/2 5 3/4 85.2 95.5 105 164 *Maximum bore shown is with standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. These type “B” and “C” sprockets are made without keyways or setscrews. They are furnished with a minimum bore which can be rebored to size and keywayed for a reasonable extra charge. Steel Triple Sprockets with Browning Split Taper® Bushings Table No. 2 HARDENED TEETH DIAMETERS No. DIMENSIONS Part Bore Wt. Less Bushing Type No. Range Outside Pitch Teeth T M OL L P C H Bushing T60P13 P2 3/4 - 1 3/4” 3.49” 3.134” 13 22 .444” 2.238” 4 1/32” 2 15/16” 1 19/32” 7/8” 3” 3.3 3 7/8 2 15/16 1 7/16 47/64 3 3.3 T60P14 P2 3/4 - 1 3/4 3.74 3.371 14 22 .444 2.238 3 4.0 T60P15 P2 3/4 - 1 3/4 3.98 3.607 15 22 .444 2.238 3 47/64 2 15/16 1 19/64 19/32 T60P16 P1 1/2 - 1 3/4 4.22 3.844 16 24 .444 2.238 3 1/8 1 15/16 5/8 15/16 3 3.4 T60Q17 Q2 3/4 - 2 11/16 4.46 4.082 17 22 .444 2.238 4 3/8 3 1/2 1 29/32 5/8 4 1/8 4.6 T60Q18 T60Q19 T60Q20 T60Q21 T60Q22 Q2 Q2 Q2 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 4.70 4.95 5.19 5.43 5.67 4.319 4.557 4.794 5.032 5.270 18 19 20 21 22 22 22 22 24 24 .444 .444 .444 .444 .444 2.238 4 15/64 2.238 3 63/64 2.238 3 53/64 2.238 3 1/4 2.238 3 1/4 3 1/2 1 3/4 1/2 4 1/8 3 1/2 1 1/2 1/4 4 1/8 3 1/2 1 23/64 3/32 4 1/8 2 1/2 3/4 15/32 4 1/8 2 1/2 3/4 15/32 4 1/8 5.0 5.9 7.0 5.7 6.6 T60Q23 T60Q24 T60Q25 T60Q26 T60Q27 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 5.91 6.15 6.39 6.63 6.87 5.508 23 5.746 24 5.984 25 6.222 26 6.460 27 25 25 25 25 25 .444 .444 .444 .444 .444 2.238 2.238 2.238 2.238 2.238 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1/4 1/4 1/4 1/4 1/4 0 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 7.7 8.8 10.0 11.1 12.4 T60Q28 T60R30 T60R32 T60R35 T60R36 Q1 R1 R1 R1 R1 3/4 - 2 11/16 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 7.11 7.59 8.07 8.78 9.02 6.699 28 7.175 30 7.652 32 8.367 35 8.605 36 25 25 25 25 25 .444 .444 .444 .444 .444 2.238 2 25/32 2.238 3 5/32 2.238 3 5/32 2.238 3 5/32 2.238 3 5/32 2 1/2 2 7/8 2 7/8 2 7/8 2 7/8 1/4 5/8 5/8 5/8 5/8 0 0 0 0 0 4 1/8 5 3/8 5 3/8 5 3/8 5 3/8 13.6 14.0 19.0 22.0 23.4 T60R40 T60R42 T60R52 T60S68 R1 R1 R1 S1 1 1/8 - 3 3/4 9.98 9.559 40 1 1/8 - 3 3/4 10.46 10.036 42 1 1/8 - 3 3/4 12.85 12.422 52 1 11/16 - 4 1/4 16.67 16.240 68 25 25 25 22 .444 .444 .444 .444 2.238 2.238 2.238 2.238 2 7/8 2 7/8 2 7/8 4 3/8 5/8 5/8 5/8 2 9/64 0 0 0 0 5 3/8 5 3/8 5 3/8 6 3/8 31.3 35.3 63.2 122 36 42 52 DIMENSIONS T M OL L P .444” 2.238” 3 1/4” 2 3/4” 37/64” .444 2.238 3 1/4 2 3/4 37/64 .444 2.238 3 1/4 2 3/4 37/64 C 0 0 0 H 6” 6 6 Wt. Less Bushing 23.9 36.7 62.6 68 76 95 .444 2.238 3 9/16 2 3/4 .444 2.238 3 9/16 2 3/4 .444 2.238 3 9/16 2 3/4 19/64” 19/64 19/64 6 6 6 116 148 238 Steel Triple Sprockets with Q-D® Bushings Table No. 3 DIAMETERS Part Bore No. Bushing No. Range Outside Pitch Teeth T60E36 E 7/8 - 3 1/2” 9.02” 8.605” QD-9 T60E42 E 7/8 - 3 1/2 10.46 10.036 QD-9 T60E52 E 7/8 - 3 1/2 12.85 12.422 QD-9 T60E68 T60E76 T60E95 3 5/32 3 5/32 3 5/32 5 1/8 E E E 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 16.67 18.58 23.12 16.240 QD-9 18.149 QD-9 22.683 QD-9 Type 7/8 7/8 7/8 H-34 Roller Chain Sprockets Steel Single Sprockets with Browning Split Taper® Bushings HARDENED TEETH Table No. 1 Standard Keyseats Table No. 2 Bore Range Keyseat 3/8" — 7/16" 1/2 — 9/16 5/8 — 7/8 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 3 3/8 — 3 3/4 None 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 7/8 x 7/16 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-35 80 Part No. Bushing Bore Range H80H10 H80H11 H80P11 H80P12 H80P13 H H P1 P1 P1 H80P14 H80Q14 H80P15 H80Q15 H80P16 P1 Q1 P1 Q1 P1 1/2 - 1 3/4 3/4 - 2 11/16 1/2 - 1 3/4 3/4 - 2 11/16 1/2 - 1 3/4 H80Q16 H80P17 H80Q17 H80P18 H80Q18 Q1 P1 Q1 P1 Q1 H80P19 H80Q19 H80Q20 H80Q21 H80Q22 DIAMETERS Wt. Less L P C H Bushing 1 1/4” 1 21/64” 21/32” 2 1/2” 2.0 1 1/4 3/4 1/16 2 1/2 1.3 1 15/16 1 17/32 5/32 3 1.8 1 15/16 1 3/8 0 3 2.0 1 15/16 1 3/8 0 3 2.3 DIMENSIONS No. Type Pitch Teeth T Nom. 3.236” 10 3 .575” 3.550 11 3 .575 3.550 11 4 .575 3.864 12 4 .575 4.179 13 4 .575 OL 2 3/32” 1 1/2 2 11/32 2 3/16 2 3/16 4.98 4.98 5.31 5.31 5.63 4.494 4.494 4.810 4.810 5.126 14 14 15 15 16 4 4 4 4 4 .575 .575 .575 .575 .575 2 3/16 1 15/16 1 3/8 2 25/32 2 1/2 1 15/16 2 3/16 1 15/16 1 3/8 2 25/32 2 1/2 1 15/16 2 3/16 1 15/16 1 3/8 0 0 0 0 0 3 4 1/8 3 4 1/8 3 2.7 3.0 3.2 3.6 3.6 3/4 - 2 11/16 1/2 - 1 3/4 3/4 - 2 11/16 1/2 - 1 3/4 3/4 - 2 11/16 5.63 5.95 5.95 6.27 6.27 5.126 5.442 5.442 5.759 5.759 16 17 17 18 18 4 4 4 4 4 .575 .575 .575 .575 .575 2 25/32 2 1/2 1 15/16 2 3/16 1 15/16 1 3/8 2 25/32 2 1/2 1 15/16 2 3/16 1 15/16 1 3/8 2 25/32 2 1/2 1 15/16 0 0 0 0 0 4 1/8 3 4 1/8 3 4 1/8 4.6 3.9 5.4 4.5 6.0 P1 Q1 Q1 Q1 Q1 1/2 - 1 3/4 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 6.59 6.59 6.91 7.24 7.56 6.079 6.079 6.392 6.710 7.027 19 19 20 21 22 4 4 4 4 4 .575 .575 .575 .575 .575 2 3/16 1 15/16 2 25/32 2 1/2 2 25/32 2 1/2 2 25/32 2 1/2 2 25/32 2 1/2 1 3/8 1 15/16 1 15/16 1 15/16 1 15/16 0 0 0 0 0 3 4 1/8 4 1/8 4 1/8 4 1/8 4.8 6.4 6.9 7.4 8.0 H80Q23 H80Q24 H80Q25 H80Q26 H80Q27 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 7.88 8.20 8.52 8.84 9.16 7.344 7.661 7.979 8.296 8.614 23 24 25 26 27 4 4 4 4 4 .575 .575 .575 .575 .575 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 0 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 8.5 9.3 9.9 10.4 10.9 H80Q28 H80Q29 H80Q30 80Q31 80Q32 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 9.48 8.931 9.80 9.567 10.11 9.567 10.43 9.885 10.75 10.202 28 29 30 31 32 4 4 4 4 4 .575 .575 .575 .575 .575 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 0 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 11.5 12.5 13.0 13.9 14.8 80Q33 80Q34 80Q35 80Q36 80R36 Q1 Q1 Q1 Q1 R1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 1 1/8 - 3 3/4 11.07 11.39 11.71 11.98 11.98 10.520 10.838 11.156 11.474 11.474 33 34 35 36 36 4 4 4 4 4 .575 .575 .575 .575 .575 2 25/32 2 25/32 2 25/32 2 25/32 3 5/32 2 1/2 2 1/2 2 1/2 2 1/2 2 7/8 1 15/16 1 15/16 1 15/16 1 15/16 2 5/16 0 0 0 0 0 4 1/8 4 1/8 4 1/8 4 1/8 5 3/8 15.5 16.3 17.8 18.1 19.5 80Q37 80Q38 80R39 80Q40 80R40 Q1 Q1 R1 Q1 R1 3/4 - 2 11/16 3/4 - 2 11/16 1 1/8 - 3 3/4 3/4 - 2 11/16 1 1/8 - 3 3/4 12.35 12.67 12.99 13.31 13.31 11.792 12.110 12.428 12.746 12.746 37 38 39 40 40 4 4 4 4 4 .575 .575 .575 .575 .575 2 25/32 2 25/32 3 5/32 2 25/32 3 5/32 2 1/2 2 1/2 2 7/8 2 1/2 2 7/8 1 15/16 1 15/16 2 5/16 1 15/16 2 5/16 0 0 0 0 0 4 1/8 4 1/8 5 3/8 4 1/8 5 3/8 18.5 20.0 22.8 21.9 23.4 80R41 80Q42 80R42 80R44 R1 Q1 R1 R1 1 1/8 - 3 3/4 3/4 - 2 11/16 1 1/8 - 3 3/4 1 1/8 - 3 3/4 13.63 13.94 13.94 14.58 13.064 13.382 13.382 14.018 41 42 42 44 4 4 4 4 .575 .575 .575 .575 3 5/32 2 25/32 3 5/32 3 5/32 2 7/8 2 1/2 2 7/8 2 7/8 2 5/16 1 15/16 2 5/16 2 5/16 0 0 0 0 5 3/8 4 1/8 5 3/8 5 3/8 23.9 23.8 25.4 27.2 80Q45 80R45 80R47 80Q48 Q1 R1 R1 Q1 3/4 - 2 11/16 1 1/8 - 3 3/4 1 1/8 - 3 3/4 3/4 - 2 11/16 14.90 14.90 15.54 15.86 14.336 14.336 14.972 15.290 45 45 47 48 4 4 4 4 .575 .575 .575 .575 2 25/32 3 5/32 3 5/32 2 25/32 2 1/2 2 7/8 2 7/8 2 1/2 1 15/16 2 5/16 2 5/16 1 15/16 0 0 0 0 4 1/8 5 3/8 5 3/8 4 1/8 27.8 28.5 31.0 30.8 80R48 80R50 80Q54 80R54 80R56 R1 R1 Q1 R1 R1 1 1/8 - 3 3/4 1 1/8 - 3 3/4 3/4 - 2 11/16 1 1/8 - 3 3/4 1 1/8 - 3 3/4 15.86 16.50 17.77 17.77 18.41 15.290 15.926 17.198 17.198 17.835 48 50 54 54 56 4 4 4 4 4 .575 .575 .575 .575 .575 3 5/32 3 5/32 2 25/32 3 5/32 3 5/32 2 7/8 2 7/8 2 1/2 2 7/8 2 7/8 2 5/16 2 5/16 1 15/16 2 5/16 2 5/16 0 0 0 0 0 5 3/8 5 3/8 4 1/8 5 3/8 5 3/8 32.3 35.1 38.5 40.8 44.0 80Q60 80R60 80Q70 80R70 Q1 R1 Q1 R1 3/4 - 2 11/16 1 1/8 - 3 3/4 3/4 - 2 11/16 1 1/8 - 3 3/4 19.68 19.68 22.83 22.83 19.107 19.107 22.289 22.289 60 60 70 70 4 4 4 4 .575 .575 .575 .575 2 25/32 3 5/32 3 5/32 2 25/32 2 1/2 2 7/8 2 1/2 2 7/8 1 15/16 2 5/16 1 15/16 2 5/16 0 0 0 0 4 1/8 5 3/8 4 1/8 5 3/8 46.8 47.3 60.0 63.5 80Q72 80R72 80R80 Q1 R1 R1 3/4 - 2 11/16 1 1/8 - 3 3/4 1 1/8 - 3 3/4 23.46 22.926 43.46 22.926 26.01 25.471 72 72 80 4 5 5 .575 .575 .575 2 25/32 3 5/32 3 5/32 2 1/2 2 7/8 2 7/8 1 15/16 0 7/8 1 7/16 7/8 1 7/16 4 1/8 5 3/8 5 3/8 67.5 69.4 85.0 80R84 80R96 80S112 R1 R1 S1 1 1/8 - 3 3/4 27.33 26.744 84 1 1/8 - 3 3/4 31.15 30.563 96 1 11/16 - 4 1/4 36.24 35.655 112 5 5 5 .575 .575 .575 3 5/32 3 5/32 4 3/4 2 7/8 2 7/8 4 3/8 5 3/8 5 3/8 6 3/8 90.0 110 165 Outside 3/8 - 1 1/2” 3.68” 3/8 - 1 1/2 3.98 1/2 - 1 3/4 3.98 1/2 - 1 3/4 4.33 1/2 - 1 3/4 4.66 7/8 7/8 1 1/8 1 7/16 1 7/16 2 3/4 Were two sprockets with the same number of teeth but different bushings are offered, we suggest using the one with the larger bushing for heavier service, shock load and high torque drives. Roller Chain Sprockets Sprockets for No. 80 , 1" Pitch ANSI Chain Steel Single Sprockets with Q-D® Bushings Table No. 1 HARDENED TEETH 80 DIAMETERS DIMENSIONS Bushing Bore Range H80SH11* H80SH12 H80SDS13 H80SDS14 H80SK15* SH SH SDS SDS SK 1/2 - 1 5/8” 1/2 - 1 5/8 1/2 - 2 1/2 - 2 1/2 - 2 5/8 Outside 4.01” 4.33 4.66 4.98 5.30 Pitch 3.550” 3.864 4.179 4.494 4.810 QD-1 QD-1 QD-1 QD-1 QD-1 11 12 13 14 15 OL L P .575” 1 23/32* 1 5/16” 59/64” .575 1 23/32 1 5/16 59/64 .575 1 21/32 1 5/16 55/64 .575 1 21/32 1 5/16 55/64 .575 2 11/32 1 15/16 1 31/64 C - H80SK16 H80SK17 H80SK18 H80SK19 H80SF20 SK SK SK SK SF 1/2 - 2 5/8 1/2 - 2 5/8 1/2 - 2 5/8 1/2 - 2 5/8 1/2 - 2 15/16 5.63 5.95 6.27 6.59 6.91 5.126 5.442 5.759 6.076 6.392 QD-1 QD-1 QD-1 QD-1 QD-1 16 17 18 19 20 .575 .575 .575 .575 .575 2 11/32 2 11/32 2 11/32 2 11/32 2 15/32 1 15/16 1 15/16 1 15/16 1 15/16 2 1/16 1 31/64 1 31/64 1 31/64 1 31/64 1 35/64 - 3 7/8 3 7/8 3 7/8 3 7/8 4 5/8 3.55 3.98 4.47 4.93 5.7 H80SF21 H80SF22 H80SF23 H80SF24 H80SF25 SF SF SF SF SF 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 7.24 7.56 7.88 8.20 8.52 6.710 7.027 7.344 7.661 7.979 QD-1 QD-1 QD-1 QD-1 QD-1 21 22 23 24 25 .575 .575 .575 .575 .575 2 15/32 2 15/32 2 15/32 2 15/32 2 15/32 2 1/16 2 1/16 2 1/16 2 1/16 2 1/16 1 35/64 1 35/64 1 35/64 1 35/64 1 35/64 - 4 5/8 4 5/8 4 5/8 4 5/8 4 5/8 6.3 6.8 7.4 7.9 8.5 H80SF26 H80SF27 H80SF28 H80SF30 80SF32 SF SF SF SF SF 1/2 - 2 15/16 8.84 8.296 1/2 - 2 15/16 9.16 8.614 1/2 - 2 15/16 9.48 8.931 1/2 - 2 15/16 10.11 9.567 1/2 - 2 15/16 10.75 10.202 QD-1 QD-1 QD-1 QD-1 QD-1 26 27 28 30 32 .575 .575 .575 .575 .575 2 15/32 2 15/32 2 15/32 2 15/32 2 15/32 2 1/16 2 1/16 2 1/16 2 1/16 2 1/16 1 35/64 1 35/64 1 35/64 1 35/64 1 35/64 - 4 5/8 4 5/8 4 5/8 4 5/8 4 5/8 9.2 9.8 10.5 12.0 13.5 80SF33 80SF34 80SF35 80SF36 80SF40 SF SF SF SF SF 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 11.07 11.39 11.71 12.03 13.31 10.520 10.838 11.156 11.474 12.746 QD-1 QD-1 QD-1 QD-1 QD-1 33 34 35 36 40 .575 .575 .575 .575 .575 2 15/32 2 15/32 2 15/32 2 15/32 2 15/32 2 1/16 2 1/16 2 1/16 2 1/16 2 1/16 1 35/64 1 35/64 1 35/64 1 35/64 1 35/64 - 4 5/8 4 5/8 4 5/8 4 5/8 4 5/8 14.3 15.1 16.0 16.9 20.7 80SF42 80SF45 80SF48 80SF54 80SF60 SF SF SF SF SF 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 13.94 14.90 15.86 17.77 19.68 13.382 14.336 15.290 17.198 19.107 QD-1 QD-1 QD-1 QD-1 QD-1 42 45 48 54 60 .575 .575 .575 .575 .575 2 15/32 2 15/32 2 15/32 2 15/32 2 15/32 2 1/16 2 1/16 2 1/16 2 1/16 2 1/16 1 35/64 1 35/64 1 35/64 1 35/64 1 35/64 - 4 5/8 4 5/8 4 5/8 4 5/8 4 5/8 23.1 25.9 29.4 37.0 45.5 80E70 80E72 80E80 80E84 80E96 80F112 E E E E E F 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 1-4 22.87 23.50 26.05 27.33 31.15 36.24 22.289 22.926 25.471 26.744 30.563 35.655 QD-2 QD-2 QD-2 QD-2 QD-2 QD-2 70 72 80 84 96 112 .575 .575 .575 .575 .575 .575 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 4 3/8 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 3 3/4 1 3/16 1 1/2 1 3/16 1 1/2 1 3/16 1 1/2 1 3/16 1 1/2 1 3/16 1 1/2 1 3/8 2 7/16 6 6 6 6 6 6 5/8 64.4 67.9 83.0 91.1 118 157 Type No. Teeth T Nom. Wt. Less H Bushing 2 11/16” 1.33 2 11/16 1.65 3 1/8 1.78 3 1/8 2.21 3 7/8 3.21 Part No. * Bushing mounts with capscrews on “A” side only. Table No. 2 HARDENED TEETH Part No. H809 H8010 H8011 H8012 H8013 H8014 H8015 H8016 H8017 H8018 H8019 H8020 H8021 H8022 H8023 H8024 H8025 H8026 H8027 H8028 H8029 H8030 8032 8035 8036 Steel Finished Bore Single Sprockets DIAMETERS No. STOCK BORES MARKED "X" Type Teeth Outside Pitch 1” 1 1/8” 1 3/16” 1 1/4” 1 3/8” 1 7/16” 1 1/2” 1 9/16” 1 5/8” 1 3/4” 1 7/8” 1 15/16” 3.35” 2.924” 9 1 X X X X 3.68 3.236 10 1 X X X X 4.01 3.550 11 1 X X X X X X X X X 4.33 3.864 12 1 X X X X X X X X X X 4.66 4.179 13 1 X X X X X X X X X X X X 4.98 4.494 14 1 X X X X X X X X X X X 5.31 7.810 15 1 X X X X X X X X X X X 5.63 5.126 16 1 X X X X X X X X X 5.96 5.442 17 1 X X X X X X X X X 6.27 5.759 18 1 X X X X X X X X X 6.59 6.076 19 1 X X X X X X X X X 6.91 6.392 20 1 X X X X X X X X X 7.24 6.710 21 1 X X X X X X X X X 7.56 7.027 22 1 X X X X X X X X X 7.88 7.344 23 1 X X X X X X X X X 8.20 7.661 24 1 X X X X X X X X X 8.52 7.979 25 1 X X X X X X X X X 8.84 8.296 26 1 X X X X X X X 9.16 8.614 27 1 X X X X X X X 9.48 8.931 28 1 X X X X X X X 9.80 9.249 29 1 X X X X X X X 10.11 9.567 30 1 X X X X X X X X X 10.75 10.202 32 1 X 11.71 11.156 35 1 12.03 11.474 36 1 X DIMENSIONS 2” 2 3/16” 2 7/16” 2 15/16” T Norm L Max. P .575” 1 5/8” 47/64” .575 1 5/8 47/64 .575 1 5/8 47/64 .575 1 5/8 47/64 X .575 1 5/8 47/64 X .575 1 5/8 47/64 X .575 1 5/8 47/64 X X X .575 1 1/2 47/64 X X X .575 1 1/2 47/64 X X X .575 1 5/8 47/64 X X X .575 1 1/2 47/64 X X X .575 1 5/8 47/64 X X X .575 1 5/8 47/64 X X X .575 1 5/8 13//64 X X X .575 1 5/8 13/64 X X X .575 1 5/8 47/64 X X X .575 1 5/8 13/64 X X X X .575 1 15/16 1 23/64 X X X X .575 1 15/16 1 23/64 X X X X .575 1 15/16 1 23/64 X X X X .575 1 15/16 1 23/64 X X X X .575 1 15/16 1 23/64 .575 1 15/16 1 23/64 X .575 1 15/16 1 23/64 .575 1 15/16 1 23/64 Wt. Lbs. 1.1 1.5 2.0 2.5 2.9 3.9 4.4 6.1 7.5 7.3 7.5 8.7 9.3 10.3 10.9 10.4 12.1 11.1 15.9 16.6 17.3 14.0 15.5 18.0 18.6 All stock Finished Bore Sprockets are furnished with Standard Keyway on Centerline of Tooth Hollow Head Setscrew over Keyway. Sprockets with HARDENED TEETH have an additional Setscrew at 90° to Keyway. H-36 Roller Chain Sprockets Type "A" Steel Plate Sprockets Table No. 1 Standard Keyseats Table No. 3 Bore Range Keyseat 1/2" — 9/16" 5/8 — 7/8 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 3 3/8 — 3 3/4 3 7/8 — 4 1/2 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 7/8 x 7/16 1 x 1/2 80 Part No. Outside Dia. Pitch Dia. No. Teeth Stock Bore T (Nom.) Wt. Lbs. Part No. Outside Dia. Pitch Dia. No. Teeth Stock Bore T (Nom.) Wt. Lbs. 80A9 80A10 80A11 80A12 80A13 3.35” 3.68 4.01 4.33 4.66 2.924” 3.236 3.550 3.864 4.179 9 10 11 12 13 3/4” 3/4 3/4 3/4 3/4 .575” .575 .575 .575 .575 1.0 1.2 1.5 1.8 2.1 80A40 80A41 80A42 80A46 80A44 13.31” 13.63 13.94 14.26 14.58 12.428” 13.064 13.382 13.700 14.018 40 41 42 43 44 1 1 1 1 1 .575” .575 .575 .575 .575 20.0 20.7 21.3 23.0 23.9 80A14 80A15 80A16 80A17 80A18 4.98 5.30 5.63 5.95 6.27 4.494 4.810 5.126 5.442 5.759 14 15 16 17 18 3/4 3/4 3/4 3/4 3/4 .575 .575 .575 .575 .575 2.5 2.8 3.2 3.6 4.1 80A45 80A46 80A47 80A48 80A49 14.90 15.22 15.54 15.86 16.18 14.336 14.654 14.972 15.290 15.608 45 46 47 48 49 1 1 1 1 1 .575 .575 .575 .575 .575 25.7 26.3 27.5 28.8 31.3 80A19 80A20 80A21 80A22 80A23 6.59 6.91 7.24 7.56 7.88 6.076 6.392 6.710 7.027 7.344 19 20 21 22 23 3/4 3/4 3/4 3/4 3/4 .575 .575 .575 .575 .575 4.5 5.0 5.6 6.1 6.7 80A50 80A51 80A52 80A53 80A54 16.50 16.81 17.13 17.45 17.77 15.926 16.244 16.562 16.880 17.168 50 51 52 53 54 1 1 1 1 1 .575 .575 .575 .575 .575 32.4 33.9 36.1 34.9 35.6 80A24 80A25 80A26 80A27 80A28 8.20 8.52 8.84 9.16 9.48 7.661 7.979 8.296 8.614 8.931 24 25 26 27 28 3/4 3/4 1 1 1 .575 .575 .575 .575 .575 7.3 7.9 8.0 8.7 9.5 80A55 80A56 80A57 80A58 80A59 18.09 18.41 18.73 19.04 19.36 17.517 17.835 18.153 18.471 18.789 55 56 57 58 59 1 1 1 1 1 .575 .575 .575 .575 .575 38.1 39.9 40.6 41.8 43.0 80A29 80A30 80A31 80A32 80A33 9.80 10.11 10.43 10.75 11.07 9.249 9.567 9.885 10.202 10.520 29 30 31 32 33 1 1 1 1 1 .575 .575 .575 .575 .575 10.1 11.0 11.8 12.4 13.5 80A60 80A65 80A70 80A72 80A76 19.64 21.23 22.83 23.46 24.74 19.107 20.698 22.289 22.926 24.198 60 65 70 72 76 1 1 1 1 1 7/16 .575 .575 .575 .575 .575 43.6 53.4 62.0 63.0 71.4 80A34 80A35 80A36 80A37 80A38 80A39 11.39 11.71 11.98 12.35 12.67 12.99 10.838 11.156 11.474 11.792 12.110 12.428 34 35 36 37 38 39 1 1 1 1 1 1 .575 .575 .575 .575 .575 .575 14.3 15.0 15.6 16.6 17.4 19.0 80A80 80A84 80A90 80A96 80A112 26.01 27.33 29.20 31.11 36.20 25.471 26.744 28.654 30.563 35.655 80 84 90 96 112 1 7/16 1 7/16 1 7/16 1 7/16 1 7/16 .575 .575 .575 .575 .575 77.0 86.0 97.0 119 153 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. Steel Single Type "B" Minimum Bore Sprockets Table No. 2 Part No. DIAMETERS B B B B B Stock 3/4” 3/4 3/4 3/4 3/4 Max.* 1 1/16” 1 5/16 1 1/2 1 5/8 1 7/8 T Nom. .575” .575 .575 .575 .575 DIMENSIONS L P Max. 1 5/8 47/64” 1 5/8 47/64 1 5/8 47/64 1 5/8 47/64 1 5/8 47/64 H 1 61/64† 2 17/64† 2 37/64† 2 57/64† 3 13/64† 13 14 15 16 17 B B B B B 3/4 3/4 3/4 3/4 3/4 2 1/8 2 1/4 2 1/2 2 5/8 2 5/8 .575 .575 .575 .575 .575 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 47/64 47/64 47/64 47/64 47/64 3 5/32 3 3/8 3 13/16 3 7/8 4 1/4 3.5 4.3 5.2 5.6 6.0 18 19 20 21 22 B B B B B 3/4 3/4 3/4 3/4 3/4 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 .575 .575 .575 .575 .575 1 1/2 1 5/8 1 5/8 1 5/8 1 5/8 47/64 47/64 47/64 1 3/64 1 3/64 4 1/4 4 1/4 4 1/4 4 1/4 4 1/4 7.0 7.5 8.0 9.8 10.3 No. Teeth Type 8 9 10 11 12 4.179 4.494 4.810 5.126 5.442 5.759 6.076 6.392 6.710 7.027 80B8 80B9 80B10 80B11 80B12 Outside 3.01” 3.35 3.68 4.01 4.33 Pitch 2.613” 2.924 3.236 3.550 3.864 80B13 80B14 80B15 80B16 80B17 4.66 4.98 5.31 5.63 5.95 80B18 80B19 80B20 80B21 80B22 6.27 6.59 6.91 7.24 7.56 BORE Wt. Lbs. 1.5 2.0 2.6 3.2 4.0 *Maximum bore shown is with standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. †Hub is recessed for chain clearance These Type “B” and “C” Sprockets are furnished with no keyway and no setscrew. They are made with minimum bore which can be rebored to size, keywayed and setscrewed for a reasonable extra charge. H-37 Roller Chain Sprockets Sprockets for No. 80 , 1" Pitch ANSI Chain Steel Single Type "B" Minimum Bore Sprockets Table No. 1 DIAMETERS Outside Pitch 7.88 7.344 8.20 7.661 8.52 7.979 8.84 8.296 9.16 8.614 Part No. 80B23 80B24 80B25 80B26 80B27 80 No. Teeth 23 24 25 26 27 Type B B B B B BORE Stock Max.* 3/4 2 3/4 3/4 2 3/4 3/4 2 3/4 1 3 1/4 1 3 1/4 T Nom. .575 .575 .575 .575 .575 DIMENSIONS L P Max. 1 5/8 1 3/64 1 5/8 1 3/64 1 5/8 1 3/64 1 15/16 1 23/64 1 15/16 1 23/64 H 4 1/4 4 1/4 4 1/4 4 3/4 4 3/4 Wt. Lbs. 10.9 11.5 12.1 15.2 15.9 80B28 80B29 80B30 80B31 80B32 9.48 9.80 10.11 10.43 10.75 8.931 9.249 9.567 9.885 10.202 28 29 30 31 32 B B B B B 1 1 1 1 1 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 .575 .575 .575 .575 .575 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 1 23/64 1 23/64 1 23/64 1 23/64 1 23/64 4 3/4 4 3/4 4 3/4 4 3/4 4 3/4 16.6 17.3 18.1 18.9 19.7 80B33 80B34 80B35 80B36 80B37 11.07 11.39 11.71 11.98 12.35 10.520 10.838 11.156 11.474 11.792 33 34 35 36 37 B B B B B 1 1 1 1 1 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 .575 .575 .575 .575 .575 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 1 23/64 1 23/64 1 23/64 1 23/64 1 23/64 4 3/4 4 3/4 4 3/4 4 3/4 4 3/4 20.5 21.4 22.3 23.2 24.2 80B38 80B39 80B40 80B41 80B42 12.67 12.99 13.31 13.63 13.94 12.110 12.428 12.746 13.064 13.382 38 39 40 41 42 B B B B B 1 1 1 1 1 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 .575 .575 .575 .575 .575 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 1 23/64 1 23/64 1 23/64 1 23/64 1 23/64 4 3/4 4 3/4 4 3/4 4 3/4 4 3/4 25.1 26.1 27.2 28.2 29.3 80B44 80B45 80B46 80B47 14.58 14.90 15.22 15.54 14.018 14.336 14.654 14.972 44 45 46 47 B B B B 1 1 1 1 3 1/4 3 1/4 3 1/2 3 1/2 .575 .575 .575 .575 1 15/16 1 15/16 1 15/16 1 15/16 1 23/64 1 23/64 1 23/64 1 23/64 4 3/4 4 3/4 5 1/4 5 1/4 31.5 32.7 35.4 36.6 80B48 80B49 80B50 80B53 15.86 16.18 16.50 17.45 15.290 15.608 15.926 16.880 48 49 50 53 B B B B 1 1 1 1 3 1/2 3 1/2 3 1/2 3 1/2 .575 .575 .575 .575 1 15/16 1 15/16 1 15/16 1 15/16 1 23/64 1 23/64 1 23/64 1 23/64 5 1/4 5 1/4 5 1/4 5 1/4 37.8 39.1 40.3 44.4 80B54 80B55 80B56 80B57 17.77 18.09 18.41 18.73 17.198 17.517 17.835 18.153 54 55 56 57 B B B B 1 1 1 1 3 1/2 3 1/2 3 1/2 3 1/2 .575 .575 .575 .575 1 15/16 1 15/16 1 15/16 1 15/16 1 23/64 1 23/64 1 23/64 1 23/64 5 1/4 5 1/4 5 1/4 5 1/4 45.7 47.2 48.7 50.2 80B60 80B65 80B70 80C70 80C72 19.68 21.27 22.83 22.83 23.46 19.107 20.698 22.289 22.289 22.926 60 65 70 70 72 B B B C C 1 1 1 1 1 3 1/2 3 1/2 3 1/2 4 3/8 4 3/8 .575 .575 .575 .575 .575 1 15/16 1 15/16 1 15/16 2 5/8 2 5/8 1 23/64 1 23/64 1 23/64 1 1/32 1 1/32 5 1/4 5 1/4 5 1/4 6 3/8 6 3/8 54.6 62.7 75.6 81.4 85.1 80C76 80C80 80C90 80C96 80C112 24.74 26.05 29.20 31.15 36.20 24.198 25.471 28.654 30.563 35.655 76 80 90 96 112 C C C C C 1 7/16 1 7/16 1 7/16 1 7/16 1 7/16 4 3/8 4 3/8 4 3/8 4 3/8 4 3/8 .575 .575 .575 .575 .575 2 5/8 2 5/8 2 5/8 2 5/8 2 5/8 1 1/32 1 1/32 1 1/32 1 1/32 1 1/32 6 3/8 6 3/8 6 3/8 6 3/8 6 3/8 92.1 100 122 137 180 *Maximum bore shown is with standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. †Hub is recessed for chain clearance These Type “B” and “C” Sprockets are furnished with no keyway and no setscrew. They are made with minimum bore which can be rebored to size, keywayed and setscrewed for a reasonable extra charge. Steel Double Sprockets with Browning Split Taper® Bushings HARDENED TEETH Table No. 2 DIAMETERS No. Type Outside Pitch Teeth DIMENSIONS Wt. Less Bushing 3.6 5.4 5.4 4.8 6.0 Part No. Bushing Bore Range D80P13 D80Q14 D80Q15 D80Q16 D80Q17 P1 Q2 Q2 Q1 Q1 1/2 - 1 3/4” 1 - 2 5/8 1 -2 5/8 3/4 - 2 11/16 3/4 - 2 11/16 4.66” 4.179” 13 4.98 4.494 14 5.31 4.810 15 5.63 5.126 16 5.95 5.442 17 13 .557” 1.710” 2 19/32” 1 15/16” 5/8” 13/32” 12 .557 1.710 3 51/64 3 1/2 1 55/64 1/16 12 .557 1.710 3 51/64 3 1/2 1 55/64 1/16 13 .557 1.710 2 25/32 2 1/2 27/32 1/32 13 .557 1.710 2 25/32 2 1/2 27/32 1/32 D80Q18 D80Q19 D80R20 D80R21 D80R22 Q1 Q1 R1 R1 R1 3/4 - 2 11/16 3/4 - 2 11/16 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 6.27 6.59 6.91 7.24 7.56 5.759 6.076 6.392 6.710 7.027 13 13 12 12 12 2 25/32 2 25/32 3 5/32 3 5/32 3 5/32 2 1/2 2 1/2 2 7/8 2 7/8 2 7/8 27/32 1/32 4 1/8 27/32 1/32 4 1/8 1 5/32 5 3/8 1 5/32 5 3/8 1 5/32 5 3/8 7.3 8.5 7.8 9.4 10.8 D80R23 D80R24 D80R25 R1 R1 R1 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 7.88 8.20 8.52 7.344 23 12 .557 1.710 3 5/32 7.661 24 12 .557 1.710 3 5/32 7.979 25 12 .557 1.710 3 5/32 LARGER SIZES ON NEXT PAGE 2 7/8 2 7/8 2 7/8 1 5/32 1 5/32 1 5/32 12.3 14.1 15.8 18 19 20 21 22 T .557 .557 .557 .557 .557 M 1.710 1.710 1.710 1.710 1.710 OL L P C - H 3” 4 1/8 4 1/8 4 1/8 4 1/8 5 3/8 5 3/8 5 3/8 H-38 80 Roller Chain Sprockets Steel Double Sprockets with Browning Split Taper® Bushings Table No. 1 Bushing Bore Range D80R26 D80R27 D80R28 D80R30 D80R36 R1 R1 R1 R1 R1 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 D80R42 D80R45 D80R48 D80R52 D80R54 R1 R1 R2 R2 R2 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 3/8 - 3 5/8 1 3/8 - 3 5/8 1 3/8 - 3 5/8 13.94 14.90 15.86 17.13 17.77 13.382 14.336 15.290 16.562 17.198 42 45 48 52 54 12 12 15 15 15 .557 .557 .557 .557 .557 1.710 1.710 1.710 1.710 1.710 D80R60 D80R68 D80R72 D80U76 D80U95 R2 R2 R2 U0 U0 1 3/8 - 3 5/8 1 3/8 - 3 5/8 1 3/8 - 3 5/8 2 3/8 - 5 1/2 2 3/8 - 5 1/2 19.64 22.23 23.46 24.74 30.83 19.107 21.653 22.926 24.198 30.245 60 68 72 76 95 15 15 15 15 15 .557 .557 .557 .557 .557 1.710 1.710 1.710 1.710 1.710 H Wt. Less Bushing - 5 3/8” 5 3/8 5 3/8 5 3/8 5 3/8 18.1 20.4 22.7 26.8 41.6 3 5/32 3 5/32 5 5/32 5 5/32 5 5/32 2 7/8” 1 5/32 5 3/8 2 7/8” 1 5/32 5 3/8 4 7/8 7/8 2 9/32 5 3/8 4 7/8 7/8 2 9/32 5 3/8 4 7/8 7/8 2 9/32 5 3/8 58.0 68.0 86.0 103 111 5 5/32 5 5/32 5 5/32 5 23/32 5 23/32 4 7/8 4 7/8 4 7/8 5 1/4 5 1/4 135 176 198 219 342 7/8 7/8 7/8 1 1/2 1 1/2 2 9/32 2 9/32 2 9/32 2 1/32 2 1/32 5 3/8 5 3/8 5 3/8 8 3/8 8 3/8 Steel Double Sprockets with Q-D® Bushings Table No. 2 DIAMETERS Part No. Bushing Bore Range Outside Pitch D80E36 D80E42 D80E45 D80E52 E E E E 7/8 - 3 1/2” 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 12.03” 13.94 14.90 17.13 11.474” 13.382 14.336 16.562 D80E60 D80E68 D80E76 E E E 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 19.68 22.23 24.78 Type No. Teeth T QD-6 QD-6 QD-6 QD-6 36 42 45 52 .557” .557 .557 .557 19.107 QD-6 21.653 QD-6 24.198 QD-6 60 68 76 .557 1.710 .557 1.710 .557 1.710 M DIMENSIONS OL L P Max. C H 1 7/64” 1 7/64 1 7/64 1 7/64 - 6” 6 6 6 Wt. Less Bushing 41.1 58.5 68.3 93.9 3 1/4 3 1/4 3 1/4 2 3/4 1 7/64 2 3/4 1 7/64 2 3/4 1 7/64 - 6 6 6 128 166 210 1.710” 3 1/4” 1.710 3 1/4 1.710 3 1/4 1.710 3 1/4 2 3/4” 2 3/4 2 3/4 2 3/4 DIAMETERS Wt. Lbs. .557” .557 .557 .557 .557 DIMENSIONS L P H Max 1.710” 2 3/4” 1 3/64” 2 9/16”† 1.710 2 1/2 51/64 2 1/2 1.710 2 1/2 51/64 2 27/32 1.710 2 1/2 51/64 3 5/32 1.710 2 1/2 51/64 3 15/32 2 1/2 2 3/4 3 3 1/4 3 5/16 .557 .557 .557 .557 .557 1.710 1.710 1.710 1.710 1.710 2 1/2 2 3/4 2 3/4 2 3/4 2 3/4 51/64 1 3/64 1 3/64 1 3/64 1 3/64 3 51/64 4 4 27/64 4 47/64 5 9.5 11.7 13.7 15.6 17.6 1 1 1 1 1 1 1 1 1 1 1 3 5/16 3 5/16 3 5/16 3 5/16 3 1/2 3 1/2 3 1/2 3 3/4 3 3/4 3 3/4 3 3/4 .557 .557 .557 .557 .557 .557 .557 .557 .557 .557 .557 1.710 1.710 1.710 1.710 1.710 1.710 1.710 1.710 1.710 1.710 1.710 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 3 3 3 3 3 3 1/8 1 3/64 1 3/64 1 3/64 1 3/64 1 3/64 1 19/64 1 19/64 1 19/64 1 19/64 1 19/64 1 27/64 5 5 5 5 5 1/4 5 1/4 5 1/4 5 3/4 5 3/4 5 3/4 5 3/4 18.9 20.5 22.1 23.7 26.0 29.3 31.2 41.0 45.6 58.9 56.6 DB DB DB DC 1 1 1/4 1 1/4 1 7/16 3 3/4 4 4 4 .557 .557 .557 .557 1.710 1.710 1.710 1.710 3 1/8 3 1/8 3 1/8 3 3/4 1 27/64 1 27/64 1 27/64 1 1/64 5 3/4 6 6 6 68.0 74.7 84.5 114 DC DC DC DC 1 1/2 1 1/2 1 1/2 1 1/2 4 4 1/4 4 1/4 4 1/2 .557 .557 .557 .557 1.710 1.710 1.710 1.710 3 3/4 4 4 4 1/4 1 1/64 1 9/64 1 9/64 1 17/64 6 6 1/4 6 1/4 6 1/2 148 190 210 311 Part No. Outside Pitch No. Teeth Type D80B10 D80B11 D80B12 D80B13 D80B14 3.68” 4.01 4.33 4.66 4.98 3.236” 3.550 3.864 4.179 4.494 10 11 12 13 14 D80B15 D80B16 D80B17 D80B18 D80B19 5.31 5.63 5.95 6.27 6.59 4.810 5.126 5.442 5.759 6.076 D80B20 D80B21 D80B22 D80B23 D80B24 D80B25 D80B26 D80B30 D80B32 D80B35 D80B36 6.91 7.24 7.56 7.88 8.20 8.52 8.84 10.11 10.75 11.71 12.03 D80B40 D80B42 D80B45 D80C52 D80C60 D80C68 D80C76 D80C95 BORE Stock Max. * T DB DB DB DB DB 3/4” 3/4 3/4 1 1 1 1/2” 1 5/8 1 7/8 2 1/4 2 3/8 15 16 17 18 19 DB DB DB DB DB 1 1 1 1 1 6.392 6.710 7.027 7.344 7.661 7.979 8.296 9.567 10.202 12.156 11.474 20 21 22 23 24 25 26 30 32 35 36 DB DB DB DB DB DB DB DB DB DB DB 13.31 13.94 14.90 17.13 12.746 13.382 14.336 16.562 40 42 45 52 19.68 22.23 24.78 30.83 19.107 21.653 24.198 30.245 60 68 76 95 *Maximum bore shown is with standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. †Hub is recessed for chain clearance These Type “B” and “C” Sprockets are furnished with no keyway and no setscrew. They are made with minimum bore which can be rebored to size, keywayed and setscrewed for a reasonable extra charge. Table No. 4 M 4.3 5.2 5.8 6.7 8.1 Standard Keyseats Bore Range Keyseat Bore Range Keyseat 1/2" — 9/16" 5/8 — 7/8 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 2 5/16" — 2 3/4" 2 13/16 — 3 1/4 3 3/8 — 3 3/4 3 7/8 — 4 1/2 4 5/8 — 5 1/2 5/8" x 5/16" 3/4 x 3/8 7/8 x 7/16 1 x 1/2 1 1/4 x 5/8 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. HARDENED TEETH Steel Double Type "B" and "C" Minimum Bore Sprockets Table No. 3 H-39 C DIAMETERS No. DIMENSIONS Type Outside Pitch Teeth T M OL L P SMALLER SIZES ON PRECEDING PAGE 8.84” 8.296” 26 12 .557” 1.710” 3 5/32” 2 7/8” 1 5/32” 9.16 8.614 27 12 .557 1.710 3 5/32 2 7/8” 1 5/32 9.48 8.931 28 12 .557 1.710 3 5/32 2 7/8” 1 5/32 10.11 9.567 30 12 .557 1.710 3 5/32 2 7/8” 1 5/32 12.03 11.474 36 12 .557 1.710 3 5/32 2 7/8” 1 5/32 Part No. Roller Chain Sprockets Sprockets for 80-100 No. 80 , 1" Pitch ANSI Chain Steel Triple Sprockets with Browning Split Taper® Bushings Table No. 1 DIAMETERS Wt. (lbs.) Less Bushing 5.7 7.5 8.1 9.3 9.8 Bushing Bore Range M OL L T80P13 T80Q14 T80Q15 T80Q16 T80Q17 P1 Q2 Q2 Q2 Q2 3/4 - 1 3/4” 1 - 2 5/8 1 - 2 5/8 1 - 2 5/8 1 - 2 5/8 4.66 4.98 5.31 5.63 5.95 4.179 4.494 4.810 5.126 5.442 24 22 22 24 24 13 14 15 16 17 .557 .557 .557 .557 .557 2.863 2.863 2.863 2.863 2.863 3 11/16 4 61/64 4 61/64 2 25/32 2 25/32 1 15/16 3 1/2 3 1/2 3 1/2 3 1/2 T80Q18 T80Q19 T80R20 T80R21 T80R22 T80R23 Q2 Q2 R1 R1 R1 R1 1 - 2 5/8 1 - 2 5/8 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 6.27 6.59 6.91 7.24 7.56 7.88 5.759 6.076 6.392 6.710 7.027 7.344 24 24 24 24 24 25 18 19 20 21 22 23 .557 .557 .557 .557 .557 .557 2.863 2.863 2.863 2.863 2.863 2.863 2 25/32 2 25/32 4 1/32 4 1/32 4 1/32 3 5/32 3 1/2 3 1/2 2 7/8 2 7/8 2 7/8 2 7/8 27/32 27/32 7/8 7/8 7/8 0 3/16 3/16 7/8 7/8 7/8 0 4 1/8 4 1/8 5 3/8 5 3/8 5 3/8 5 3/8 12.0 13.9 10.2 12.4 14.6 15.9 T80R24 T80R25 T80R26 T80R27 T80R28 R1 R1 R1 R1 R1 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 8.20 8.52 8.84 9.16 9.48 7.661 7.979 8.296 8.614 8.931 25 25 25 25 25 24 25 26 27 28 .557 .557 .557 .557 .557 2.863 2.863 2.863 2.863 2.863 3 5/32 3 5/32 3 5/32 3 5/32 3 5/32 2 7/8 2 7/8 2 7/8 2 7/8 2 7/8 0 0 0 0 0 0 0 0 0 0 5 3/8 5 3/8 5 3/8 5 3/8 5 3/8 18.5 20.3 23.4 25.8 28.1 T80R30 T80S36 T80S42 T80S45 T80U52 T80U60 R1 S1 S1 S1 U0 U0 1 1/8 - 3 3/4 1 11/16 - 4 1/4 1 11/16 - 4 1/4 1 11/16 - 4 1/4 2 3/8 - 5 1/2 2 3/8 - 5 1/2 10.11 12.03 13.94 14.9 17.13 19.68 9.567 11.474 13.382 14.336 16.562 19.107 25 22 22 22 25 25 30 36 42 45 52 60 .557 .557 .557 .557 .557 .557 2.863 3 5/32 2.863 5 1/8 2.863 5 1/8 2.863 5 1/8 2.863 5 23/32 2.863 5 23/32 0 0 0 0 0 0 5 3/8 6 3/8 6 3/8 6 3/8 8 3/8 8 3/8 33.3 67.0 96.1 112 150 207 T80U68 T80U76 T80U95 U0 U0 U0 2 3/8 - 5 1/2 2 3/8 - 5 1/2 2 3/8 - 5 1/2 22.23 24.78 30.83 21.653 24.198 30.245 25 25 25 68 .557 2.863 5 23/32 5 1/4 1 25/32 0 8 3/8 76 .557 2.863 5 23/32 5 1/4 1 25/32 0 8 3/8 95 .557 2.863 5 55/64 5 1/4 1 13/32 1/32 8 3/8 271 344 183 Outside Pitch Type No. Teeth T DIMENSIONS Part No. P C H 5/8 1 35/64 3 1 7/8 1 7/32 4 1/8 1 7/8 1 7/32 4 1/8 27/32 3/16 4 1/8 27/32 3/16 4 1/8 2 7/8 0 4 3/8 1 1/2 4 3/8 1 1/2 4 3/8 1 1/2 5 1/4 1 25/32 5 1/4 1 25/32 Steel Triple Sprockets with Q-D® Bushings Table No. 2 Part No. Bushing Bore Range DIAMETERS T80E36 T80E42 T80E45 T80E52 E E E E 7/8 - 3 1/2” 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 12.03” 13.94 14.90 17.13 11.474” QD-9 13.382 QD-9 14.336 QD-9 16.562 QD-9 36 42 45 52 DIMENSIONS OL L P T M Max .557” 2.863” 3 7/8” 2 3/4” 9/16” .557 2.863 3 7/8 2 3/4 9/16 .557 2.863 3 7/8 2 3/4 9/16 .557 2.863 3 7/8 2 3/4 9/16 T80F60 T80F68 T80F76 T80F95 F F F F 1-4 1-4 1-4 1-4 19.68 22.23 24.78 30.83 19.107 21.653 24.198 30.245 60 68 76 95 .557 .557 .557 .557 Outside Pitch Type QD-9 QD-9 QD-9 QD-9 No. Teeth 2.863 2.863 2.863 2.863 3 7/8 3 7/8 3 7/8 3 7/8 3 3/4 3 3/4 3 3/4 3 3/4 1 3/16 1 3/16 1 3/16 1 3/16 C H 39/64”* 39/64* 39/64* 39/64* 6” 6 6 6 Wt. Less Bushing 61.7 90.8 107 150 11/64 11/64 11/64 11/64 6 5/8 6 5/8 6 5/8 6 5/8 207 272 345 551 *Capscrew Head is under Sprocket Rim. H-40 Roller Chain Sprockets Steel Single Sprockets with Browning Split Taper® Bushings Table No. 1 HARDENED TEETH 100 P C H 2 3/16” 1 15/16” 2 29/32 2 1/2 2 53/64 2 1/2 2 53/64 2 1/2 2 53/64 2 1/2 1 1/4” 1 63/64 1 29/32 1 29/32 1 29/32 0 11/64 3/32 3/32 3/32 3” 4 1/8 4 1/8 4 1/8 4 1/8 Wt. Less Bushing 3.0 3.5 4.3 5.6 6.5 .692 .692 .692 .692 .692 2 53/64 2 53/64 2 53/64 2 53/64 2 53/64 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1 29/32 1 29/32 1 29/32 1 29/32 1 29/32 3/32 3/32 3/32 3/32 3/32 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 7.4 8.2 9.0 9.9 10.8 4 4 4 4 4 .692 .692 .692 .692 .692 2 53/64 3 5/32 2 53/64 2 53/64 2 53/64 2 1/2 2 7/8 2 1/2 2 1/2 2 1/2 1 29/32 2 3/16 1 29/32 1 29/32 1 29/32 3/32 0 3/32 3/32 3/32 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 11.7 13.3 12.5 13.9 15.5 24 25 25 26 26 4 4 4 4 4 .692 .692 .692 .692 .692 3 5/32 2 53/64 3 5/32 2 53/64 3 5/32 2 7/8 2 1/2 2 7/8 2 1/2 2 7/8 2 3/16 0 1 29/32 3/32 2 3/16 0 1 29/32 3/32 2 3/16 0 5 3/8 4 1/8 4 1/8 4 1/8 5 3/8 16.1 16.2 17.0 17.9 18.5 10.767 10.767 11.164 11.164 11.958 11.958 27 27 28 28 30 30 4 4 4 4 4 4 .692 .692 .692 .692 .692 .692 2 53/64 3 5/32 2 53/64 3 5/32 2 53/64 3 5/32 2 1/2 2 7/8 2 1/2 2 7/8 2 1/2 2 7/8 1 29/32 3/32 2 3/16 0 1 29/32 3/32 2 3/16 0 1 29/32 3/32 2 3/16 0 4 1/8 5 3/8 4 1/8 5 3/8 4 1/8 5 3/8 18.2 19.6 19.9 21.0 22.6 24.5 13.44 13.44 14.64 14.64 15.04 12.753 12.753 13.945 13.945 14.342 32 32 35 35 36 4 4 4 4 4 .692 .692 .692 .692 .692 2 53/64 3 5/32 2 53/64 3 5/32 3 5/32 2 1/2 2 7/8 2 1/2 2 7/8 2 7/8 1 29/32 3/32 2 3/16 0 1 29/32 3/32 2 3/16 0 2 3/16 0 4 1/8 5 3/8 4 1/8 5 3/8 5 3/8 25.3 26.5 30.2 29.8 33.0 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 16.63 17.43 18.63 19.82 22.21 15.932 16.727 17.920 19.112 21.498 40 42 45 48 54 4 4 4 4 5 .692 .692 .692 .692 .692 3 5/32 3 5/32 3 5/32 3 5/32 3 5/32 2 7/8 2 7/8 2 7/8 2 7/8 2 7/8 2 3/16 0 2 3/16 0 2 3/16 0 2 3/16 0 7/8 1 5/16 5 3/8 5 3/8 5 3/8 5 3/8 5 3/8 40.9 44.3 50.5 57.5 69.0 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 24.55 28.53 29.33 32.52 34.11 23.884 27.862 28.657 31.839 33.430 60 70 72 80 84 5 5 5 5 5 .692 .692 .692 .692 .692 3 5/32 3 5/32 3 5/32 3 5/32 3 5/32 2 7/8 2 7/8 2 7/8 2 7/8 2 7/8 5 3/8 5 3/8 5 3/8 5 3/8 5 3/8 84.0 104 106 135 138 DIAMETERS Part No. Bushing Bore Range Outside Pitch No. Type Teeth T Nom. H100P11 H100Q12 H100Q13 H100Q14 H100Q15 P1 Q1 Q1 Q1 Q1 1/2 - 1 3/4 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 5.01” 5.42 5.82 6.23 6.63 4.437” 4.830 5.223 5.617 6.012 11 12 13 14 15 4 4 4 4 4 .692” .692 .692 .692 .692 H100Q16 H100Q17 H100Q18 H100Q19 H100Q20 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 7.03 7.44 7.84 8.24 8.64 6.407 6.803 7.198 7.595 7.991 16 17 18 19 20 4 4 4 4 4 H100Q21 H100R21 H100Q22 H100Q23 H100Q24 Q1 R1 Q1 Q1 Q1 3/4 - 2 11/16 1 1/8 - 3 3/4 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 9.04 9.04 9.44 9.84 10.25 8.387 8.387 8.783 9.180 9.577 21 21 22 23 24 H100R24 H100Q25 H100R25 H100Q26 H100R26 R1 Q1 R1 Q1 R1 1 1/8 - 3 3/4 3/4 - 2 11/16 1 1/8 - 3 3/4 3/4 - 2 11/16 1 1/8 - 3 3/4 10.25 10.65 10.65 11.05 11.05 9.577 9.973 9.973 10.370 10.370 H100Q27 H100R27 H100Q28 H100R28 H100Q30 H100R30 Q1 R1 Q1 R1 Q1 R1 3/4 - 2 11/16 1 1/8 - 3 3/4 3/4 - 2 11/16 1 1/8 - 3 3/4 3/4 - 2 11/16 1 1/8 - 3 3/4 11.45 11.45 11.84 11.84 12.64 12.64 100Q32 100R32 100Q35 100R35 100R36 Q1 R1 Q1 R1 R1 3/4 - 2 11/16 1 1/8 - 3 3/4 3/4 - 2 11/16 1 1/8 - 3 3/4 1 1/8 - 3 3/4 100R40 100R42 100R45 100R48 100R54 R1 R1 R1 R1 R1 100R60 100R70 100R72 100R80 100R84 R1 R1 R1 R1 R1 DIMENSIONS OL L 7/8 7/8 7/8 7/8 7/8 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 Where two sprockets with the same number of teeth but different bushings are offered, we suggest using the one with the larger bushing for heavier service drives. Standard Keyseats Table No. 2 Bore Range Keyseat 3/4" — 7/8" 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 3 3/8 — 3 3/4 3 7/8 — 4 1/4 4 5/8 — 5 1/2 3/16" x 3/32" 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 7/8 x 7/16 1 x 1/2 1 1/4 x 5/8 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-41 Roller Chain Sprockets Sprockets for No. 100 , 1 1/4" Pitch ANSI Chain Steel Single Sprockets with Q-D® Bushings Table No. 1 Part No. HARDENED TEETH 100 Bushing H100SDS11 H100SDS12 H100SK13 H100SK14 H100SF15 DIAMETERS Bore Range SDS 1/2 - 2” SDS 1/2 - 2 SK 1/2 - 2 5/8 SK 1/2 - 2 5/8 SF 1/2 - 2 15/16 Type No. Teeth T Nom. DIMENSIONS C H Wt.Less Bushing 1 5/16” 3/4” 1 5/16 3/4 1 15/16 1 3/8 1 15/16 1 3/8 2 1/16 1 7/16 - 3 1/8” 3 1/8 3 7/8 3 7/8 4 5/8 2.33 2.91 3.80 4.62 5.5 2 15/32 2 1/16 1 7/16 2 15/32 2 1/16 1 7/16 3 1/4 2 3/4 2 1/8 3 1/4 2 3/4 2 1/8 3 1/4 2 3/4 2 1/8 - 4 5/8 4 5/8 6 6 6 6.2 7.0 9.9 11.0 11.7 Outside Pitch OL 5.01” 5.42 5.82 6.23 6.63 4.437” 4.830 5.223 5.617 6.012 QD-1 QD-1 QD-1 QD-1 QD-1 11 12 13 14 15 .692” .692 .692 .692 .692 1 21/32” 1 21/32 2 11/32 2 11/32 2 15/32 L P H100SF16 H100SF17 H100E18 H100E19 H100E20 SF SF E E E 1/2 - 2 15/16 1/2 - 2 15/16 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 7.03 7.44 7.84 8.24 8.64 6.407 6.803 7.198 7.595 7.991 QD-1 QD-1 QD-1 QD-1 QD-1 16 17 18 19 20 .692 .692 .692 .692 .692 H100E21 H100E22 H100E23 H100E24 H100E25 E E E E E 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 9.04 9.44 9.84 10.25 10.65 8.387 8.783 9.180 9.557 9.973 QD-1 QD-1 QD-1 QD-1 QD-1 21 22 23 24 25 .692 .692 .692 .692 .692 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 2 1/8 2 1/8 2 1/8 2 1/8 2 1/8 - 6 6 6 6 6 12.6 13.6 14.6 15.6 16.7 H100E26 H100E27 H100E28 H100E30 E E E E 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 11.05 11.44 11.84 12.64 10.370 10.767 11.164 11.958 QD-1 QD-1 QD-1 QD-1 26 27 28 30 .692 .692 .692 .692 3 1/4 3 1/4 3 1/4 3 1/4 2 3/4 2 3/4 2 3/4 2 3/4 2 1/8 2 1/8 2 1/8 2 1/8 - 6 6 6 6 17.8 19.0 20.2 22.8 100E32 100E35 100E36 100E40 100E42 100E45 E E E E E E 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 13.44 14.64 15.04 16.63 17.43 18.63 12.753 13.945 14.342 15.932 16.727 17.920 QD-1 QD-1 QD-1 QD-1 QD-1 QD-1 32 35 36 40 42 45 .692 .692 .692 .692 .692 .692 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 2 1/8 2 1/8 2 1/8 2 1/8 2 1/8 2 1/8 - 6 6 6 6 6 6 25.5 29.9 31.5 38.2 41.8 47.5 100E48 100E54 100E60 100F70 100F72 100F80 100F84 E E E E F F F 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 1-4 1-4 1-4 1-4 19.82 22.21 24.60 28.58 29.38 32.57 34.16 19.112 21.498 23.884 27.862 28.657 31.839 33.430 QD-1 QD-2 QD-2 QD-2 QD-2 QD-2 QD-2 48 54 60 70 72 80 84 .692 .692 .692 .692 .692 .692 .692 3 1/4 3 1/4 3 1/4 4 3/8 4 3/8 4 3/8 4 3/8 2 3/4 2 3/4 2 3/4 3 3/4 3 3/4 3 3/4 3 3/4 2 1/8 1 3/16 1 3/16 1 3/8 1 3/8 1 3/8 1 3/8 1 25/64 1 25/64 2 21/64 2 21/64 2 21/64 2 21/64 6 6 6 6 5/8 6 5/8 6 5/8 6 5/8 53.7 67.1 82.2 117 123 140 154 Type "A" Steel Plate Sprockets Table No. 2 Part No. Outside Dia. Pitch Dia. 100A7 100A8 100A9 100A10 100A11 3.35” 3.77 4.18 4.60 5.01 2.881” 3.266 3.665 4.045 4.437 7 8 9 10 11 1” 1 1 1 1 100A12 100A13 100A14 100A15 100A16 5.42 5.82 6.23 6.63 7.03 4.830 5.223 5.617 6.012 6.407 12 13 14 15 16 100A17 100A18 100A19 100A20 100A21 7.44 7.84 8.24 8.64 9.04 6.803 7.198 7.595 7.991 8.387 100A22 100A23 100A24 100A25 100A26 9.44 9.84 10.25 10.65 11.05 100A27 100A28 100A29 100A30 100A31 100A32 100A33 100A34 100A35 100A36 100A37 No. Stock T Teeth Bore (Nom.) Wt. Lbs. Part No. Outside Dia. Pitch Dia. No. Stock T Teeth Bore (Nom.) Wt. Lbs. .692” .692 .692 .692 .692 .9 1.0 1.5 2.0 2.3 100A38 100A39 100A40 100A41 100A42 15.84” 16.23 16.63 17.03 17.43 15.137” 15.534 15.932 16.329 16.727 38 39 40 41 42 1” 1 1 1 1 .692” .692 .692 .692 .692 31.7 33.4 35.1 36.9 38.7 1 1 1 1 1 .692 .692 .692 .692 .692 3.1 3.4 4.1 4.8 5.4 100A43 100A44 100A45 100A46 100A47 17.83 18.23 18.63 19.02 19.42 17.124 17.522 17.920 18.317 18.715 43 44 45 46 47 1 1 1 1 1 .692 .692 .692 .692 .692 40.6 42.5 44.5 46.5 48.5 17 18 19 20 21 1 1 1 1 1 .692 .692 .692 .692 .692 6.2 7.2 7.5 8.9 9.6 100A48 100A49 100A50 100A51 100A52 19.82 20.22 20.62 21.02 21.42 19.112 19.510 19.908 20.305 20.703 48 49 50 51 52 1 1 1 1 1 .692 .692 .692 .692 .692 50.6 52.7 54.9 57.1 59.4 8.783 9.180 9.577 9.973 10.370 22 23 24 25 26 1 1 1 1 1 .692 .692 .692 .692 .692 11.3 12.0 13.3 14.1 15.3 100A53 100A54 100A55 100A56 100A57 21.81 22.21 22.61 23.01 23.41 21.100 21.498 21.896 22.296 22.691 53 54 55 56 57 1 1 1 1 1 .692 .692 .692 .692 .692 61.7 64.1 66.5 68.9 71.4 11.44 11.84 12.24 12.64 13.04 10.767 11.164 11.561 11.958 12.356 27 28 29 30 31 1 1 1 1 1 .692 .692 .692 .692 .692 16.4 17.5 19.6 20.4 22.3 100A58 100A59 100A60 100A70 100A72 23.81 24.20 24.60 28.58 29.38 23.089 23.486 23.884 27.862 28.657 58 59 60 70 72 1 1 1 1 7/16 1 7/16 .692 .692 .692 .692 .692 73.9 76.5 79.1 108 114 13.44 13.84 14.24 14.64 15.04 15.44 12.753 13.150 13.547 13.945 14.342 14.740 32 33 34 35 36 37 1 1 1 1 1 1 .692 .692 .692 .692 .692 .692 22.5 23.9 25.4 26.9 28.4 30.0 100A76 100A80 100A84 100A90 100A96 30.97 32.96 34.16 36.55 38.93 30.248 32.237 33.430 35.817 38.203 76 80 84 90 96 1 7/16 1 7/16 1 7/16 1 7/16 1 7/16 .692 .692 .692 .692 .692 127 141 155 178 202 Standard Keyseats Table No. 3 Bore Range Keyseat 1/2" — 9/16" 5/8 — 7/8 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 3 3/8 — 3 3/4 3 7/8 — 4 1/2 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 7/8 x 7/16 1 x 1/2 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-42 100 Roller Chain Sprockets Steel Single Type "B" and "C" Minimum Bore Sprockets Table No. 1 DIAMETERS Part No. Outside Pitch No. of Teeth Type 100B8 100B9 100B10 100B11 100B12 3.77” 4.18 4.60 5.01 5.42 3.266” 3.655 4.045 4.437 4.830 8 9 10 11 12 100B13 100B14 100B15 100B16 100B17 5.82 6.23 6.63 7.03 7.44 5.223 5.617 6.012 6.407 6.803 100B18 100B19 100B20 100B21 100B22 7.84 8.24 8.64 9.04 9.44 100B23 100B24 100B25 100B26 100B27 BORE DIMENSIONS Stock Max.* T Nom. L Max. P H Wt. Lbs. B B B B B 1” 1 1 1 1 1 3/8” 1 5/8 1 7/8 2 1/4 2 3/8 .692” .692 .692 .692 .692 1 7/8” 1 7/8 1 7/8 1 7/8 1 7/8 1 3/16” 1 3/16 1 3/16 1 3/16 1 3/16 2 31/64”† 2 7/8† 3 17/64† 3 21/32† 4 3/64† 2.8 3.8 5.1 6.3 5.0 13 14 15 16 17 B B B B B 1 1 1 1 1 2 5/8 2 3/4 3 3 1/4 3 1/4 .692 .692 .692 .692 .692 1 5/8 1 5/8 1 3/4 1 3/4 1 3/4 15/16 15/16 1 1/16 1 1/16 1 1/16 3 7/8 4 3/16 4 9/16 4 3/4 4 3/4 6.3 9.2 10.5 11.2 12.0 7.198 7.595 7.991 8.387 8.783 18 19 20 21 22 B B B B B 1 1 1 1 1 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 .692 .692 .692 .692 .692 1 3/4 2 2 2 2 1 1/16 1 5/16 1 5/16 1 5/16 1 5/16 4 3/4 4 3/4 4 3/4 4 3/4 4 3/4 12.9 15.0 15.9 16.9 18.0 9.84 10.25 10.65 11.05 11.44 9.180 9.577 9.973 10.370 10.767 23 24 25 26 27 B B B B B 1 1 1 1 1 3 1/4 3 1/4 3 1/4 3 1/2 3 1/2 .692 .692 .692 .692 .692 2 2 2 2 2 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 4 3/4 4 3/4 4 3/4 5 1/4 5 1/4 19.1 20.2 21.4 24.1 25.4 100B28 100B29 100B30 100B32 100B35 11.84 12.24 12.64 13.44 14.64 11.164 11.561 11.958 12.753 13.945 28 29 30 32 35 B B B B B 1 1 1 1 1 3 1/2 3 1/2 3 1/2 3 1/2 3 1/2 .692 .692 .692 .692 .692 2 2 2 2 2 1 5/16 1 5/16 1 5/16 1 5/16 1 5/16 5 1/4 5 1/4 5 1/4 5 1/4 5 1/4 26.7 28.1 29.6 32.6 37.5 100B36 100B39 100B40 100B42 100B45 15.04 16.23 16.63 17.43 18.63 14.342 15.534 15.932 16.727 17.920 36 39 40 42 45 B B B B B 1 1 1 1 1 3 1/2 3 3/4 3 3/4 3 3/4 4 .692 .692 .692 .692 .692 2 2 3/16 2 3/16 2 3/16 2 3/16 1 5/16 1 1/2 1 1/2 1 1/2 1 1/2 5 1/4 6 6 6 6 39.2 48.6 50.5 54.5 60.9 100B48 100C54 100C60 100C70 100C72 19.82 22.21 24.60 28.58 29.38 19.112 21.498 23.880 27.862 28.657 48 54 60 70 72 B C C C C 1 1 1 1 7/16 1 7/16 4 4 4 5 1/4 5 1/4 .692 .692 .692 .692 .692 2 3/16 3 1/4 3 1/4 3 1/4 3 1/4 1 1/2 1 9/32 1 9/32 1 9/32 1 9/32 6 6 6 7 1/8 7 1/8 67.7 90.8 108 147 155 100C76 100C80 100C84 100C90 100C96 30.97 32.57 34.16 36.55 38.93 30.248 29.850 33.430 35.817 38.203 76 80 84 90 96 C C C C C 1 7/16 1 7/16 1 7/16 1 7/16 1 7/16 5 1/4 5 1/4 5 1/4 5 1/4 5 1/4 .692 .692 .692 .692 .692 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 1 9/32 1 9/32 1 9/32 1 9/32 1 9/32 7 1/8 7 1/8 7 1/8 7 1/8 7 1/8 168 183 199 225 252 * Maximum bore shown is with standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. † Hub is recessed for chain clearance These type “B” and “C” Sprockets are furnished with no keyway and no setscrew. They are made with minimum bore which can be rebored to size, keywayed and setscrewed for a reasonable extra charge Steel Double Sprockets with Browning Split Taper® Bushings HARDENED TEETH Table No. 2 H-43 Part No. Bushing Bore Range T M D100P11 D100Q12 D100Q13 D100Q14 P1 Q2 Q2 Q1 1/2 - 1 3/4 1-2 5/8 1-2 5/8 3/4 - 2 11/16 5.01 5.42 5.82 6.23 4.437 4.830 5.223 5.617 11 12 13 14 14 12 12 14 .669 .669 .669 .669 2.077 2.077 2.077 2.077 2 15/16 1 15/16 5/8 3/4 4 7/32 3 1/2 1 55/64 7/16 4 7/32 3 1/2 1 55/64 7/16 3 3/32 2 1/2 3/4 5/16 Wt.(lbs) Less H Bushing 3 4.7 4 1/8 5.9 4 1/8 7.9 4 1/8 7.4 D100Q15 D100Q16 D100R17 D100R18 Q1 Q1 R1 R1 3/4 - 2 11/16 3/4 - 2 11/16 1 1/8 - 3 3/4 1 1/8 - 3 3/4 6.63 7.03 7.44 7.84 6.012 6.407 6.803 7.198 15 16 17 18 14 14 14 14 .669 .669 .669 .669 2.077 2.077 2.077 2.077 3 3/32 3 3/32 3 7/32 3 7/32 2 1/2 2 1/2 2 7/8 2 7/8 3/4 3/4 7/8 7/8 5/16 5/16 1/16 1/16 4 1/8 4 1/8 5 3/8 5 3/8 9.1 10.9 10.0 12.3 D100R19 D100R20 D100R21 D100R22 D100R24 R1 R1 R1 R1 R1 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 8.24 8.64 9.04 9.44 10.25 7.595 7.991 8.387 8.783 9.577 19 20 21 22 24 14 14 14 14 14 .669 .669 .669 .669 .669 2.077 2.077 2.077 2.077 2.077 3 7/32 3 7/32 3 7/32 3 7/32 3 7/32 2 7/8 2 7/8 2 7/8 2 7/8 2 7/8 7/8 7/8 7/8 7/8 7/8 1/16 1/16 1/16 1/16 1/16 5 3/8 5 3/8 5 3/8 5 3/8 5 3/8 14.9 17.4 20.3 22.8 29.5 D100R35 D100S45 D100S60 D100S70 D100S80 R1 S1 S1 S2 S2 1 1/8 - 3 3/4 1 11/16 - 4 1/4 1 11/16 - 4 1/4 1 7/8 - 4 3/16 1 7/8 - 4 3/16 14.64 18.63 24.60 28.58 32.57 13.945 17.920 23.884 27.862 31.839 35 45 60 70 80 14 15 15 18 18 .669 .669 .669 .669 .669 2.077 3 7/32 2.077 4 3/4 2.077 4 3/4 2.077 7 1/8 2.077 7 1/8 2 7/8 4 3/8 4 3/8 6 3/4 6 3/4 7/8 1/16 5 3/8 1 1/16 1 15/64 6 3/8 1 1/16 1 15/64 6 3/8 2 7/16 2 1/4 6 3/8 2 7/16 2 1/4 6 3/8 76.8 138 251 358 431 DIAMETERS No. of Type Outside Pitch Teeth DIMENSIONS OL L P C Roller Chain Sprockets Sprockets for No. 100 , 1 1/4" Pitch ANSI Chain Steel Minimum Bore Double Sprockets Table No. 1 HARDENED TEETH 100 DIAMETERS Stock Max.* T DB DB DB DB DB 1” 1 1 1 1 1 5/8” 1 7/8 2 1/8 2 1/4 2 1/2 .669” .669 .669 .669 .669 DIMENSIONS L P Max. 2.077” 2 7/8” 51/64” 2.077 2 7/8 51/64 2.077 2 7/8 51/64 2.077 2 7/8 51/64 2.077 2 7/8 51/64 14 15 16 17 18 DB DB DB DB DB 1 1 3/16 1 3/16 1 3/16 1 3/16 2 3/4 3 1/8 3 5/16 3 1/2 3 1/2 .669 .669 .669 .669 .669 2.077 2.077 2.077 2.077 2.077 2 7/8 3 1/8 3 1/8 3 1/8 3 1/8 7.595 7.991 8.387 8.783 9.180 19 20 21 22 23 DB DB DB DB DB 1 3/16 1 1/4 1 1/4 1 1/4 1 1/4 3 3/4 3 3/4 3 3/4 3 3/4 3 3/4 .669 .669 .669 .669 .669 2.077 2.077 2.077 2.077 2.077 10.25 10.65 11.05 12.64 14.64 9.577 9.973 10.370 11.958 13.945 24 25 26 30 35 DB DB DB DB DC 1 1/4 1 1/4 1 7/16 1 7/16 1 1/2 3 3/4 3 3/4 3 3/4 3 3/4 4 1/4 .669 .669 .669 .669 .669 18.63 24.60 28.58 32.57 17.920 23.884 27.862 31.839 45 60 70 80 DC DC DC DC 1 1/2 1 1/2 1 1/2 1 1/2 4 1/4 5 3/8 5 3/8 5 3/8 .669 .669 .669 .669 Part No. Pitch No. Teeth Outside Type D100B9 D100B10 D100B11 D100B12 D100B13 4.15” 4.60 5.01 5.40 5.82 3.655” 4.045 4.437 4.830 5.223 9 10 11 12 13 D100B14 D100B15 D100B16 D100B17 D100B18 6.23 6.63 7.03 7.44 7.84 5.617 6.012 6.407 6.803 7.198 D100B19 D100B20 D100B21 D100B22 D100B23 8.24 8.64 9.04 9.44 9.84 D100B24 D100B25 D100B26 D100B30 D100C35 D100C45 D100C60 D100C70 D100C80 BORE H Wt. Lbs. 2 13/32” 2 3/4 3 1/8 3 3/8 3 13/16 4.5 6.0 7.7 9.3 11.5 51/64 1 3/64 1 3/64 1 3/64 1 3/64 4 3/16 4 5/8 5 5 1/4 5 1/4 13.8 17.2 20.1 22.9 25.2 3 3/8 3 3/8 3 3/8 3 3/8 3 3/8 1 19/64 1 19/64 1 19/64 1 19/64 1 19/64 5 1/2 5 1/2 5 1/2 5 3/4 5 3/4 30.1 33.0 35.7 39.8 43.1 2.077 2.077 2.077 2.077 2.077 3 3/8 3 3/8 3 3/8 3 3/8 4 1/4 1 19/64 1 19/64 1 19/64 1 19/64 1 3/32 5 3/4 5 3/4 5 3/4 5 3/4 6 1/4 46.1 49.8 53.3 69.0 101 2.077 2.077 2.077 2.077 4 1/2 5 5 5 1 7/32 1 15/32 1 15/32 1 15/32 6 1/4 7 1/2 7 1/2 7 1/2 160 287 381 205 M * Maximum bores shown will accommodate standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. These sprockets are furnished with minimum bore and no keyway. They can be rebored to size, keywayed and setscrewed for a reasonable extra charge. Steel Double Sprockets with Q-D® Bushings Table No. 2 DIAMETERS Part No. Bushing Bore Range D100F35 D100F45 D100J60 D100J70 D100J80 F F J J J 1 - 4” 1-4 1 1/2 - 4 1/2 1 1/2 - 4 1/2 1 1/2 - 4 1/2 Outside Pitch 14.64” 18.63 24.60 25.58 32.57 13.945” 17.920 23.884 27.862 31.839 Type No. Teeth T M QD-4 QD-4 QD-4 QD-4 QD-4 35 45 60 70 80 .669” .669 .669 .669 .669 2.077” 2.077 2.077 2.077 2.077 DIMENSIONS OL L P Max. 4 3/8” 3 3/4” 1 3/8” 4 3/8 3 3/4 1 3/8 5 5/16 4 5/8 1 19/32 5 5/16 4 5/8 1 19/32 5 5/16 4 5/8 1 19/32 C H 27/64” 27/64 1 5/64 1 5/64 1 5/64 6 5/8” 6 5/8 7 1/4 7 1/4 7 1/4 Wt. Less Bushing 77.8 135 250 343 416 Steel Triple Sprockets with Q-D® Bushings Table No. 3 Part No. Bushing Bore Range T100F35 T100F45 T100J60 T100J70 T100J80 F F J J J 1 - 4” 1-4 1 1/2 - 4 1/2 1 1/2 - 4 1/2 1 1/2 - 4 1/2 DIAMETERS Outside Pitch 14.64” 18.63 24.60 28.58 32.57 13.945” 17.820 23.884 27.862 31.839 DIMENSIONS Type No. Teeth T M OL QD-9 QD-9 QD-7 QD-7 QD-7 35 45 50 70 80 .669” .669 .669 .669 .669 3.485” 3.485 3.485 3.485 3.485 4 7//8” 4 7/8 5 5/16 5 5/16 5 5/16 L P C H 3 3/4” 7/8” 31/64” 6 5/8” 3 3/4 7/8 31/64 6 5/8 4 5/8 7/8 25/32 7 1/4 4 5/8 7/8 25/32 7 1/4 4 5/8 7/8 25/32 7 1/4 Wt. Less Bushing 118 211 400 556 205 Standard Keyseats Table No. 4 Bore Range Keyseat 1/2" — 9/16" 5/8 — 7/8 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 3 3/8 — 3 3/4 3 7/8 — 4 1/2 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 7/8 x 7/16 1 x 1/2 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-44 Roller Chain Sprockets Sprockets for No. 120 , 1 1/2" Pitch ANSI Chain Steel Single Sprockets with Browning Split Taper® Bushings Table No. 1 HARDENED TEETH 120 OL L P C H 4 4 4 4 4 4 T Nom. .924” .924 .924 .924 .924 .924 2 25/32” 2 25/32 2 25/32 2 25/32 2 25/32 2 25/32 2 1/2” 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1 9/16” 1 9/16 1 9/16 1 9/16 1 9/16 1 9/16 0 0 0 0 0 0 4 1/8” 4 1/8 4 1/8 4 1/8 4 1/8 4 1/8 Wt. Less Bushing 4.8 6.3 7.9 9.1 10.4 11.8 16 17 17 18 18 19 4 4 4 4 4 4 .924 .924 .924 .924 .924 .924 3 5/32 2 25/32 3 5/32 2 25/32 3 5/32 3 5/32 2 7/8 2 1/2 2 7/8 2 1/2 3 5/32 3 5/32 1 15/16 1 9/16 1 15/16 1 9/16 1 9/16 1 9/16 0 0 0 0 0 0 5 3/8 4 1/8 5 3/8 4 1/8 5 3/8 5 3/8 12.3 13.4 13.6 15.6 15.9 16.8 9.589 10.064 10.540 11.016 11.492 20 21 22 23 24 4 4 4 4 4 .924 .924 .924 .924 .924 3 5/32 3 5/32 3 5/32 3 5/32 3 5/32 2 7/8 2 7/8 2 7/8 2 7/8 2 7/8 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 0 0 0 0 0 5 3/8 5 3/8 5 3/8 5 3/8 5 3/8 18.8 21.0 22.5 24.8 26.9 11.968 12.444 13.397 14.350 25 26 28 30 4 5 5 5 .924 .924 .924 .924 3 5/32 3 5/32 3 5/32 3 5/32 2 7/8 1 15/16 0 5 3/8 2 7/8 7/8 1 1/16 5 3/8 2 7/8 7/8 1 1/16 5 3/8 2 7/8 7/8 1 1/16 5 3/8 29.8 32.9 38.3 43.4 16.13 15.303 32 5 .924 3 5/32 2 7/8 49.4 17.57 18.05 19.96 19.96 20.92 16.734 17.211 19.118 19.118 20.072 35 36 40 40 42 6 6 6 5 5 .924 .924 .924 .924 .924 5 5/32 5 5/32 5 5/32 4 3/4 4 3/4 4 7/8 1 15/16 2 4 7/8 1 15/16 2 4 7/8 1 15/16 2 4 3/8 1 1/16 2 3/8 4 3/8 1 1/16 2 3/8 5 3/8 5 3/8 5 3/8 6 3/8 6 3/8 68.0 72.0 82.0 83.0 90.0 1 3/8 - 3 5/8 1 11/16 - 4 1/4 1 11/16 - 4 1/4 1 11/16 - 4 1/4 1 3/8 - 3 5/8 22.35 22.35 23.79 26.65 29.52 21.503 21.503 22.935 25.798 28.661 45 45 48 54 60 6 5 5 5 6 .924 .924 .924 .924 .924 5 5/32 4 3/4 4 3/4 4 3/4 5 5/32 4 7/8 1 15/16 2 4 3/8 1 1/16 2 3/8 4 3/8 1 1/16 2 3/8 4 3/8 1 1/16 2 3/8 4 7/8 1 15/16 2 5 3/8 6 3/8 6 3/8 6 3/8 5 3/8 102 100 111 138 179 1 11/16 - 4 1/4 1 3/8 - 3 5/8 1 11/16 - 4 1/4 1 3/8 - 3 5/8 1 7/8 - 4 3/16 29.52 34.30 34.30 39.08 39.08 28.661 33.434 33.434 38.207 38.207 60 70 70 80 80 5 6 6 6 6 .924 .924 .924 .924 .924 4 3/4 5 5/32 7 1/8 5 5/32 7 1/8 4 3/8 4 7/8 6 3/4 4 7/8 6 3/4 6 3/8 5 3/8 6 3/8 5 3/8 6 3/8 180 148 167 291 305 DIAMETERS Part No. Bushing Bore Range No. Type Outside Pitch Teeth H120Q11 H120Q12 H120Q13 H120Q14 H120Q15 H120Q16 Q1 Q1 Q1 Q1 Q1 Q1 3/4 - 2 11/16” 3/4 - 2 11/16” 3/4 - 2 11/16” 3/4 - 2 11/16” 3/4 - 2 11/16” 3/4 - 2 11/16” 6.01” 6.50 6.99 7.47 7.96 8.39 5.324” 5.796 6.268 6.741 7.215 7.689 11 12 13 14 15 16 H120R16 H120Q17 H120R17 H120Q18 H120R18 H120R19 R1 Q1 R1 Q1 R1 R1 1 1/8 - 3 3/4 3/4 - 2 11/16” 1 1/8 - 3 3/4 3/4 - 2 11/16” 1 1/8 - 3 3/4 1 1/8 - 3 3/4 8.39 8.88 8.88 9.41 9.41 9.89 7.689 8.163 8.163 8.638 8.638 9.113 H120R20 H120R21 H120R22 H120R23 H120R24 R1 R1 R1 R1 R1 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 10.37 10.85 11.33 11.81 12.29 H120R25 H120R26 H120R28 H120R30 R1 R1 R1 R1 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 12.77 13.25 14.21 15.17 120R32 R1 1 1/8 - 3 3/4 120R35 120R36 120R40 120S40 120S42 R2 R2 R2 S1 S1 1 3/8 - 3 5/8 1 3/8 - 3 5/8 1 3/8 - 3 5/8 1 11/16 - 4 1/4 1 11/16 - 4 1/4 120R45 120S45 120S48 120S54 120R60 R2 S1 S1 S1 R2 120S60 120R70 120S70 120R80 120S80 S1 R2 S2 R2 S2 DIMENSIONS 7/8 1 1/16 5 3/8 1 1/16 2 3/8 1 15/16 2 2 15/16 2 7/8 1 15/16 2 2 15/16 2 7/8 Where two sprockets with the same number of teeth but different bushings are offered, we suggest using the one with the larger bushing for heavier service drives. H-45 Roller Chain Sprockets Sprockets for No. 120 , 1 1/2" Pitch ANSI Chain Steel Single Sprockets with Q-D® Bushings Table No. 1 HARDENED TEETH 120 OL L P C H 12 13 14 15 T Nom. .924” .924 .924 .924 2 15/32” 2 15/32 2 15/32 2 15/32 2 1/16” 2 1/16 2 1/16 2 1/16 1 13/64” 1 13/64 1 13/64 1 13/64 - 4 5/8” 4 5/8 4 5/8 4 5/8 Wt. Less Bushing 5.8 6.8 8.1 9.5 QD-1 QD-1 QD-1 QD-1 16 17 18 19 .924 .924 .924 .924 3 1/4 3 1/4 3 1/4 3 1/4 2 3/4 2 3/4 2 3/4 2 3/4 1 57/64 1 57/64 1 57/64 1 57/64 - 6 6 6 6 12.4 13.9 15.4 17.0 10.37 10.85 11.33 11.81 12.29 9.589 QD-1 10.064 QD-1 10.540 QD-1 11.016 QD-1 11.492 QD-1 20 21 22 23 24 .924 .924 .924 .924 .924 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 1 57/64 1 57/64 1 57/64 1 57/64 1 57/64 - 6 6 6 6 6 18.8 20.6 22.5 24.5 26.6 12.77 13.25 14.21 15.17 11.968 QD-1 12.444 QD-1 13.397 QD-1 14.350 QD-1 25 26 28 30 .924 .924 .924 .924 3 1/4 3 1/4 3 1/4 3 1/4 2 3/4 2 3/4 2 3/4 2 3/4 1 57/64 1 57/64 1 57/64 1 57/64 - 6 6 6 6 28.8 31.0 35.8 41.0 1-4 16.13 15.303 QD-2 32 .924 4 3/8 3 3/4 1 3/8 - 6 5/8 52.0 1-4 1-4 1-4 1-4 1-4 17.57 18.05 19.96 20.92 22.35 16.734 QD-2 17.211 QD-2 19.118 QD-2 20.072 QD-2 21.503 QD-2 35 36 40 42 45 .924 .924 .924 .924 .924 4 3/8 4 3/8 4 3/8 4 3/8 4 3/8 3 3/4 3 3/4 3 3/4 3 3/4 3 3/4 1 3/8 1 3/8 1 3/8 1 3/8 1 3/8 - 6 5/8 6 5/8 6 5/8 6 5/8 6 5/8 61.0 64.1 77.6 84.9 96.5 1-4 1-4 1 1/2 - 4 1/2 1 1/2 - 4 1/2 1 1/2 - 4 1/2 23.79 26.65 29.52 34.30 39.08 22.935 QD-2 25.798 QD-2 28.661 QD-2 33.434 QD-2 38.207 QD-2 48 54 60 70 80 .924 .924 .924 .924 .924 4 3/8 4 3/8 5 5/16 5 5/16 5 5/16 3 3/4 3 3/4 4 5/8 4 5/8 4 5/8 1 3/8 6 5/8 1 3/8 6 5/8 1 9/16 2 17/64” 7 1/4 1 9/16 2 17/64 7 1/4 1 9/16 2 17/64 7 1/4 109 136 171 229 281 DIAMETERS Part No. Bushing Bore Range Type No. Teeth H120SF12* H120SF13 H120SF14 H120SF15 SF SF SF SF 1/2 - 2 15/16” 1/2 - 2 15/16 1/2 - 2 15/16 1/2 - 2 15/16 6.50” 6.99 7.47 7.96 5.796” 6.268 6.741 7.215 QD-1 QD-1 QD-1 QD-1 H120E16 H120E17 H120E18 H120E19 E E E E 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 8.44 8.92 9.41 9.89 7.689 8.163 8.638 9.113 H120E20 H120E21 H120E22 H120E23 H120E24 E E E E E 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 H120E25 H120E26 H120E28 H120E30 E E E E 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 7/8 - 3 1/2 120F32 F 120F35 120F36 120F40 120F42 120F45 F F F F F 120F48 120F54 120J60 120J70 120J80 F F J J J Outside Pitch DIMENSIONS *Bushing mounts with capscrews on “B” side only. Steel Type "A" Plate Sprockets Table No. 2 Part No. Outside Dia. Pitch Dia. No. Stock T Teeth Bore (Nom.) Wt. Lbs Part No. Outside Dia. Pitch Dia. 120A8 120A9 120A10 120A11 120A12 120A13 4.52” 5.02 5.52 6.01 6.50 6.99 3.920” 4.386 4.854 5.324 5.796 6.268 8 9 10 11 12 13 1” 1 1 1 1 1 120A14 120A15 120A16 120A17 120A18 120A19 7.47 7.96 8.39 8.88 9.41 9.89 6.741 7.215 7.689 8.163 8.638 9.113 14 15 16 17 18 19 120A20 120A21 120A22 120A23 120A24 120A25 10.37 10.85 11.33 11.81 12.29 12.77 9.589 10.064 10.450 11.016 11.492 11.968 20 21 22 23 24 25 No. Stock Teeth Bore T (Nom.) Wt. Lbs .924” .924 .924 .924 .924 .924 2.8 3.5 4.4 5.3 6.3 7.4 120A26 120A27 120A28 120A30 120A32 120A34 13.25” 13.73 14.21 15.17 16.13 17.09 12.444” 12.921 13.397 14.350 15.303 16.257 26 27 28 30 32 34 1” 1 1 1 1 1 .924” .924 .924 .924 .924 .924 29.9 32.3 34.8 40.0 45.3 51.2 1 1 1 1 1 1 .924 .924 .924 .924 .924 .924 8.6 9.9 11.3 12.8 14.3 15.9 120A35 120A36 120A40 120A42 120A45 120A48 17.57 18.05 19.96 20.92 22.35 23.79 16.734 17.211 19.118 20.072 21.503 22.935 35 36 40 42 45 48 1 1 1 7/16 1 7/16 1 1/2 1 1/2 .924 .924 .924 .924 .924 .924 54.3 57.4 71.0 80.0 87.0 105 1 1 1 1 1 1 .924 .924 .924 .924 .924 .924 17.7 19.5 21.4 23.4 25.5 27.7 120A54 120A60 120A70 120A80 120A90 26.65 29.52 34.30 39.08 43.85 25.798 28.661 33.434 38.207 42.981 54 60 70 80 90 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 .924 .924 .924 .924 .924 137 164 211 286 350 Standard Keyseats Table No. 3 Bore Range Keyseat 1/2" — 9/16" 5/8 — 7/8 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 3 3/8 — 3 3/4 3 7/8 — 4 1/2 4 5/8 — 5 1/2 1/8” x 1/16” 3/16 x 3/32 1/4 x 1/8 5/16 x 5/32 3/8 x 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 7/8 x 7/16 1 x 1/2 1 1/4 x 5/8 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-46 120 Roller Chain Sprockets Steel Single Minimum Bore Sprockets Table No. 1 DIAMETERS 1 3/4” 2 1/4 2 3/8 2 3/4 3 T Nom. .924” .924 .924 .924 .924 DIMENSIONS L P H Max. 2 1/4” 1 21/64” 3 31/64”† 2 1/4 1 21/64 3 61/64† 2 1 5/64 3 9/16 2 1 5/64 4 1/8 2 1/4 1 21/64 4 9/16 7.1 9.0 11.4 10.8 14.2 1 1 1 1 1 3 1/4 3 1/4 3 1/2 3 1/2 3 1/2 .924 .924 .924 .924 .924 2 1/4 2 1/4 2 1/4 2 1/4 2 1/4 1 21/64 1 21/64 1 21/64 1 21/64 1 21/64 4 3/4 4 3/4 5 1/4 5 1/4 5 1/4 15.5 16.8 19.8 21.3 22.9 B B B B B 1 1 1 1 1 3 1/2 3 1/2 3 1/2 3 1/2 3 1/2 .924 .924 .924 .924 .924 2 1/4 2 1/4 2 1/4 2 1/4 2 1/4 1 21/64 1 21/64 1 21/64 1 21/64 1 21/64 5 1/4 5 1/4 5 1/4 5 1/4 5 1/4 24.7 26.5 28.4 30.4 32.5 24 25 26 28 30 B B B B B 1 1 1 1 1 3 1/2 3 1/2 4 4 4 .924 .924 .924 .924 .924 2 1/4 2 1/4 2 7/16 2 7/16 2 7/16 1 21/64 1 21/64 1 33/64 1 33/64 1 33/64 5 1/4 5 1/4 6 6 6 34.7 37.0 43.4 48.4 53.9 15.303 16.734 17.211 19.118 20.072 32 35 36 40 42 B B B C C 1 1 1 1 7/16 1 7/16 4 4 4 4 1/2 4 1/2 .924 .924 .924 .924 .924 2 7/16 2 7/16 2 7/16 3 3 1 33/64 1 33/64 1 33/64 1 1/32 1 1/32 6 6 6 6 5/8 6 5/8 59.7 69.1 72.4 93.9 102 21.503 22.935 25.798 28.661 33.434 38.207 45 48 54 60 70 80 C C C C C C 1 7/16 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 4 1/2 4 1/2 4 1/2 5 3/8 5 3/8 5 3/8 .924 .924 .924 .924 .924 .924 3 1/16 3 1/16 3 1/16 3 1/16 3 1/16 3 1/16 1 1/16 1 1/16 1 1/16 1 1/16 1 1/16 1 1/16 6 5/8 6 5/8 6 5/8 7 5/8 7 5/8 7 5/8 114 127 156 195 256 326 Part No. Outside Pitch No. Teeth Type 120B9 120B10 120B11 120B12 120B13 5.02” 5.52 6.01 6.50 6.99 4.386” 4.854 5.324 5.796 6.268 9 10 11 12 13 120B14 120B15 120B16 120B17 120B18 7.47 7.96 8.39 8.88 9.41 6.741 7.215 7.689 8.163 8.638 120B19 120B20 120B21 120B22 120B23 9.89 10.37 10.85 11.33 11.81 120B24 120B25 120B26 120B28 120B30 BORE Stock Max. * B B B B B 1 1 1 1 1 14 15 16 17 18 B B B B B 9.113 9.589 10.064 10.540 11.016 19 20 21 22 23 12.29 12.77 13.25 14.21 15.17 11.492 11.968 12.444 13.397 14.350 120B32 120B35 120B36 120C40 120C42 16.13 17.57 18.05 19.96 20.92 120C45 120C48 120C54 120C60 120C70 120C80 22.35 23.79 26.65 29.52 34.30 39.08 Wt. Lbs. * Maximum bores shown will accommodate standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. † Hub is recessed for chain clearance These sprockets are furnished with minimum bore and no keyway. They can be rebored to size, keywayed and setscrewed for a reasonable extra charge. Steel Double Sprockets with Browning Split Taper® Bushings Table No. 2 Bushing Bore Range D120S30 D120S35 D120S45 D120U60 S1 S1 S2 U0 1 11/16 - 4 1/4” 1 11/16 - 4 1/4 1 7/8 - 4 3/16 2 3/8 - 5 1/2 Outside Pitch 15.17” 17.57 22.35 29.52 14.350” 16.734 21.503 28.661 Type 15 15 18 15 No. Teeth DIMENSIONS T M OL 30 .894” 2.683” 4 3/4” 35 .894 2.683 4 3/4 45 .894 2.683 7 1/8 60 .894 2.683 5 23/32 L 4 3/8” 4 3/4 6 3/4 5 1/4 P C 1 1/16” 5/8” 1 1/16 5/8 2 7/32 1 27/32 19/32 1 9/32 H 6 3/8” 6 3/8 6 3/8 8 3/8 Wt. Less Bushing 105 148 268 183 Steel Double Sprockets with Q-D® Bushings Table No. 3 H-47 DIAMETERS Part No. Part No. Bushing D120J30 D120J35 D120J45 J J J Bore Range DIMENSIONS Outside Pitch Type 1 1/2 - 4 1/2” 15.17” 14.350” QD-4 1 1/2 - 4 1/2 17.57 16.734 QD-4 1 1/2 - 4 1/2 22.35 21.502 QD-4 No. Teeth 30 35 45 Wt. Less T M OL L P C H Bushing .894” 2.683” 5 5/16” 4 5/8” 1 13/32” 21/32” 7 1/4” 103 .894 2.683 5 5/16 4 5/8 1 13/32 21/32 7 1/4 145 .894 2.683 5 5/16 4 5/8 1 13/32 21/32 7 1/4 251 DIMENSIONS Roller Chain Sprockets Sprockets for 120-140 No. 120 , 1 1/2" Pitch ANSI Chain Steel Minimum Bore Double Sprockets Table No. 1 DIAMETERS Part No. Outside D120B11 D120B12 D120B13 D120B14 D120B15 Stock Max.* T DB DB DB DB DB 1 1/2” 1 1/2 1 1/2 1 1/2 1 1/2 2 3/8” 2 3/4 3 3 5/16 3 3/4 .894” .894 .894 .894 .894 DIMENSIONS L P Max. 2.683” 3 3/4” 1 1/16” 2.683 3 3/4 1 1/16 2.683 3 3/4 1 1/16 2.683 3 3/4 1 1/16 2.683 3 3/4 1 1/16 16 17 18 19 20 DB DB DB DB DB 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 3 3/4 3 3/4 3 3/4 3 3/4 3 3/4 .894 .894 .894 .894 .894 2.683 2.683 2.683 2.683 2.683 3 3/4 3 3/4 3 3/4 3 3/4 3 3/4 10.064 10.540 11.016 11.492 11.968 21 22 23 24 25 DB DB DB DB DB 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 3 3/4 3 3/4 4 1/2 4 1/2 4 1/2 .894 .894 .894 .894 .894 2.683 2.683 2.683 2.683 2.683 12.444 14.350 16.734 21.503 28.661 26 30 35 45 60 DB DB DC DC DC 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 4 1/2 4 1/2 5 3/8 5 3/8 5 3/8 .894 .894 .894 .894 .894 2.683 2.683 2.683 2.683 2.683 Pitch No. Teeth Type 6.01” 6.50 6.99 7.47 7.96 5.324” 5.796 6.268 6.741 7.215 11 12 13 14 15 D120B16 D120B17 D120B18 D120B19 D120B20 8.39 8.88 9.41 9.89 10.37 7.689 8.163 8.638 9.113 9.589 D120B21 D120B22 D120B23 D120B24 D120B25 10.85 11.33 11.81 12.29 12.77 D120B26 D120B30 D120C35 D120C45 D120C60 13.25 15.17 17.57 22.35 29.52 BORE H Wt. Lbs 3 9/16” 4 1/16 4 9/16 5 5 1/2 13.7 17.4 21.6 25.8 31.0 1 1/16 1 1/16 1 1/16 1 1/16 1 1/16 5 1/2 5 1/2 5 3/4 5 3/4 5 3/4 34.6 38.2 44.6 49.0 55.0 3 3/4 4 4 4 4 1 1/16 1 5/16 1 5/16 1 5/16 1 5/16 5 3/4 5 3/4 6 1/2 6 1/2 6 1/2 60.3 67.6 76.1 82.2 88.6 4 4 6 6 6 1 5/16 1 5/16 1 21/32 1 21/32 1 21/32 6 1/2 6 1/2 7 1/2 7 1/2 9 1/2 95.2 124 195 301 361 M * Maximum bores shown will accommodate standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. These sprockets are furnished with minimum bore and no keyway. They can be rebored to size, keywayed and setscrewed for a reasonable extra charge. Sprockets for , 1 3/4" Pitch ANSI Chain Steel Single Sprockets with Browning Split Taper® Bushings Table No. 2 HARDENED TEETH No. 140 DIMENSIONS C H Q1 Q1 R1 R1 R1 No. Type T OL Outside Pitch Teeth Nom. 3/4 - 2 11/16” 7.01” 6.212” 11 4 .924” 2 25/32” 3/4 - 2 11/16 7.58 6.762 12 4 .924 2 25/32 1 1/8 - 3 3/4 8.15 7.313 13 4 .924 3 5/32 1 1/8 - 3 3/4 8.72 7.864 14 4 .924 3 5/32 1 1/8 - 3 3/4 9.28 8.417 15 4 .924 3 5/32 2 1/2” 1 9/16” 2 1/2 1 9/16 2 7/8 1 15/16 2 7/8 1 15/16 2 7/8 1 15/16 0 0 0 0 0 4 1/8” 4 1/8 5 3/8 5 3/8 5 3/8 Wt. Less Bushing 6.4 9.0 11.1 12.6 14.7 H140R16 H140R17 H140R18 H140R19 H140R20 R1 R1 R1 R1 R1 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 9.85 10.41 10.97 11.54 12.10 8.970 9.524 10.078 10.632 11.187 16 17 18 19 20 4 4 4 4 4 .924 .924 .924 .924 .924 3 5/32 3 5/32 3 5/32 3 5/32 3 5/32 2 7/8 2 7/8 2 7/8 2 7/8 2 7/8 1 15/16 1 15/16 1 15/16 1 15/16 1 15/16 0 0 0 0 0 5 3/8 5 3/8 5 3/8 5 3/8 5 3/8 16.5 18.5 20.5 23.0 25.4 H140R21 H140R22 H140R23 H140R24 H140R25 R1 R1 R1 R1 R1 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 12.66 13.22 13.78 14.34 14.90 11.742 12.297 12.852 13.407 13.963 21 22 23 24 25 4 5 5 5 5 .924 .924 .924 .924 .924 3 5/32 3 5/32 3 5/32 3 5/32 3 5/32 2 7/8 2 7/8 2 7/8 2 7/8 2 7/8 1 15/16 7/8 7/8 7/8 7/8 0 1 1/16 1 1/16 1 1/16 1 1/16 5 3/8 5 3/8 5 3/8 5 3/8 5 3/8 27.8 32.5 36.0 37.6 40.3 H140R26 H140R30 R1 R2 1 1/8 - 3 3/4 1 3/8 - 3 5/8 15.46 17.70 14.518 16.742 26 30 5 6 .924 .924 3 5/32 5 5/32 2 7/8 4 7/8 7/8 7/8 1 1/16 2 5 3/8 5 3/8 44.0 68.0 140R35 140R36 R2 R2 1 3/8 - 3 5/8 1 3/8 - 3 5/8 20.49 21.05 19.523 20.079 35 36 6 6 .924 .924 5 5/32 5 5/32 4 7/8 4 7/8 7/8 7/8 2 2 5 3/8 5 3/8 88.0 90.0 140S36 140R40 140S40 140S45 S1 R2 S1 S1 1 11/16 - 4 1/4 1 3/8 - 3 5/8 1 11/16 - 4 1/4 1 11/16 - 4 1/4 21.05 23.29 23.29 26.08 20.079 22.305 22.305 25.087 36 40 40 45 5 6 5 5 .924 .924 .924 .924 4 3/4 5 5/32 4 3/4 4 3/4 4 3/8 4 7/8 4 3/8 4 3/8 1 1/16 7/8 1 1/16 1 1/16 2 3/8 2 2 3/8 2 3/8 6 3/8 5 3/8 6 3/8 6 3/8 89.0 109 107 132 140S48 140S54 140S60 140S70 140S80 S2 S2 S2 S2 S2 1 7/8 - 4 3/16 1 7/8 - 4 3/16 1 7/8 - 4 3/16 1 7/8 - 4 3/16 1 7/8 - 4 3/16 27.75 31.10 34.44 40.02 45.59 26.757 30.097 33.438 39.006 44.575 48 54 60 70 80 6 6 6 6 6 .924 .924 .924 .924 .924 7 1/2 7 1/2 7 1/2 7 1/2 7 1/2 6 3/4 6 3/4 6 3/4 6 3/4 6 3/4 2 15/16 2 15/16 2 15/16 2 15/16 2 15/16 2 7/8 2 7/8 2 7/8 2 7/8 2 7/8 6 3/8 6 3/8 6 3/8 6 3/8 6 3/8 169 208 230 311 242 Part No. Bushing H140Q11 H140Q12 H140R13 H140R14 H140R15 Bore Range DIAMETERS L P H-48 Roller Chain Sprockets Steel Single Sprockets with Q-D® Bushings HARDENED TEETH Table No. 1 Bore Range DIAMETERS Wt. Less Bushing Bushing C H H140SF11 SF 1/2 - 2 15/16” 7.01” 6.212” QD-1 11 .924” 2 15/32” 2 1/16” 1 13/64” - 4 5/8” 6.4 H140SF12 SF 1/2 - 2 15/16 7.58 6.762 QD-1 12 .924 2 15/32 2 1/16 1 13/64 - 4 5/8 8.2 H140SF13 SF 1/2 - 2 15/16 8.15 7.313 QD-1 13 .924 2 15/32 2 1/16 1 13/64 - 4 5/8 9.8 H140E14 E 7/8 - 3 1/2 8.72 7.864 QD-1 14 .924 3 1/4 2 3/4 1 57/64 - 6 12.8 H140E15 E 7/8 - 3 1/2 9.28 8.417 QD-1 15 .924 3 1/4 2 3/4 1 57/64 - 6 14.8 H140E16 E 7/8 - 3 1/2 9.85 8.970 QD-1 16 .924 3 1/4 2 3/4 1 57/64 - 6 16.5 H140E17 E 7/8 - 3 1/2 10.41 9.524 QD-1 17 .924 3 1/4 2 3/4 1 57/64 - 6 18.5 20.6 Outside Pitch Type No. Teeth DIMENSIONS Part No. T Nom. OL L P H140E18 E 7/8 - 3 1/2 10.98 10.078 QD-1 18 .924 3 1/4 2 3/4 1 57/64 - 6 H140E19 E 7/8 - 3 1/2 11.54 10.632 QD-1 19 .924 3 1/4 2 3/4 1 57/64 - 6 22.9 H140E20 E 7/8 - 3 1/2 12.10 11.187 QD-1 20 .924 3 1/4 2 3/4 1 57/64 - 6 25.2 H140F23 F 1-4 13.78 12.852 QD-1 23 .924 4 3/8 3 3/4 2 61/64 - 6 5/8 38.6 H140F24 F 1-4 14.34 13.407 QD-1 24 .924 4 3/8 3 3/4 2 61/64 - 6 5/8 41.4 H140F25 F 1-4 14.90 13.963 QD-1 25 .924 4 3/8 3 3/4 2 61/64 - 6 5/8 44.4 - H140F26 F 1-4 15.46 14.518 QD-1 26 .924 4 3/8 3 3/4 2 61/64 6 5/8 47.5 H140F30 F 1-4 17.70 16.742 QD-1 30 .924 4 3/8 3 3/4 2 61/64 1 37/64” 6 5/8 61.0 140F35 F 1-4 20.49 19.523 QD-2 35 .924 4 3/8 3 3/4 1 3/8 1 37/64 6 5/8 80.6 140F36 F 1-4 21.05 20.079 QD-2 36 .924 4 3/8 3 3/4 1 3/8 1 37/64 6 5/8 84.9 140J40 J 1 1/2 - 4 23.29 22.305 QD-2 40 .924 5 5/16 4 5/8 1 9/16 2 17/64 7 1/4 108 140J45 J 1 1/2 - 4 26.08 25.087 QD-2 45 .924 5 5/16 4 5/8 1 9/16 2 17/64 7 1/4 134 140J48 J 1 1/2 - 4 27.75 26.757 QD-2 48 .924 5 5/16 4 5/8 1 9/16 2 17/64 7 1/4 151 140J60 J 1 1/2 - 4 34.44 33.438 QD-2 60 .924 5 5/16 4 5/8 1 9/16 2 17/64 7 1/4 214 Standard Keyseats Table No. 2 Bore Range Keyseat 1/2" — 9/16" 5/8 — 7/8 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 3 3/8 — 3 3/4 3 7/8 — 4 1/2 4 5/8 — 5 1/2 1/8” X 1/16” 3/16 X 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 7/8 x 7/16 1 x 1/2 1 1/4 x 5/8 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-49 140 Roller Chain Sprockets 140 No. 140 Sprockets for , 1 3/4" Pitch ANSI Chain Type "A" Steel Plate Sprockets Table No. 1 Part No. Outside Dia. Pitch Dia. No. Teeth Stock Bore T (Nom.) Wt. Lbs. Part No. Outside Dia. Pitch Dia. No. Teeth Stock Bore T (Nom.) Wt. Lbs. 140A11 140A12 140A13 140A14 140A15 7.01” 7.58 8.15 8.72 9.28 6.212” 6.672 7.313 7.864 8.917 11 12 13 14 15 1 7/16” 1 7/16 1 1/2 1 1/2 1 1/2 .924” .924 .924 .924 .924 7.1 8.3 8.8 10.6 12.1 140A26 140A27 140A28 140A30 140A31 15.46” 16.02 16.58 17.70 18.26 14.518” 15.074 15.630 16.742 17.298 26 27 28 30 31 1 1/2” 1 1/2 1 1/2 1 1/2 1 1/2 .924” .924 .924 .924 .924 40.6 45.3 47.1 54.0 57.0 140A16 140A17 140A18 140A19 140A20 9.85 10.41 10.97 11.54 12.10 8.970 9.524 10.078 10.632 11.187 16 17 18 19 20 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 .924 .924 .924 .924 .924 14.5 16.4 18.4 20.5 23.8 140A32 140A35 140A36 140A40 140A45 18.82 20.49 21.05 23.29 26.08 17.854 19.523 20.079 22.305 25.087 32 35 36 40 45 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 .924 .924 .924 .924 .924 60.5 74.0 75.0 97.0 124 140A21 140A22 140A23 140A24 140A25 12.66 13.22 13.78 14.34 14.90 11.742 12.297 12.852 13.407 13.963 21 22 23 24 25 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 .924 .924 .924 .924 .924 25.7 28.3 32.1 35.3 37.6 140A48 140A54 140A60 140A70 140A80 27.75 31.10 34.44 40.02 45.59 26.757 30.097 33.438 39.006 44.575 48 54 60 70 80 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 .924 .924 .924 .924 .924 141 185 225 305 370 Steel Minimum Bore Single Sprockets Table No. 2 DIAMETERS DIMENSIONS L P Max. 2 1/4” 1 21/64” 2 1/4 1 21/64 2 3/8 1 29/64 2 3/8 1 29/64 2 3/8 1 29/64 H Wt. Lbs. 2 3/4” 3 1/4 3 3/4 3 3/4 4 1/4 T Nom. .924” .924 .924 .924 .924 4 1/4” 4 3/4 5 1/2 5 1/2 6 1/4 12.2 15.0 19.5 21.3 26.0 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 4 1/4 4 1/4 4 1/4 4 1/4 4 1/4 .924 .924 .924 .924 .924 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1 37/64 1 37/64 1 37/64 1 37/64 1 37/64 6 1/4 6 1/4 6 1/4 6 1/4 6 1/4 29.0 31.1 33.3 35.6 38.1 B B B 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 4 1/4 4 1/4 4 1/4 4 1/4 4 1/4 4 1/4 .924 .924 .924 .924 .924 .924 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 2 1/2 1 37/64 1 37/64 1 37/64 1 37/64 1 37/64 1 37/64 6 1/4 6 1/4 6 1/4 6 1/4 6 1/4 6 1/4 40.7 43.5 46.4 49.3 52.5 55.7 27 28 30 32 35 40 B B B B C C 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 4 3/8 4 3/8 4 3/8 4 3/8 5 1/4 5 3/8 .924 .924 .924 .924 .924 .924 2 1/2 2 1/2 2 1/2 2 1/2 4 4 1 37/64 1 37/64 1 37/64 1 37/64 1 17/32 1 17/32 6 3/8 6 3/8 6 3/8 6 3/8 7 7 1/2 59.7 63.2 70.6 78.5 110 139 45 48 54 60 70 80 C C C C C C 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 5 3/8 5 3/8 5 3/8 5 1/2 5 1/2 5 1/2 .924 .924 .924 .924 .924 .924 4 4 4 4 1/2 4 1/2 4 1/2 1 17/32 1 17/32 1 17/32 1 25/32 1 25/32 1 25/32 7 1/2 7 1/2 7 1/2 8 8 8 166 184 223 278 361 457 Part No. Outside Pitch No. Teeth Type 140B11 140B12 140B13 140B14 140B15 7.01” 7.58 8.15 8.72 9.28 6.212” 6.762 7.313 7.864 8.417 11 12 13 14 15 140B16 140B17 140B18 140B19 140B20 9.85 10.41 10.98 11.54 12.10 8.970 9.524 10.078 10.632 11.187 140B21 140B22 140B23 140B24 140B25 140B26 12.66 13.22 13.78 14.34 14.90 15.46 140B27 140B28 140B30 140B32 140C35 140C40 140C45 140C48 140C54 140C60 140C70 140C80 BORE Stock Max.* B B B B B 1 7/16” 1 7/16 1 1/2 1 1/2 1 1/2 16 17 18 19 20 B B B B B 11.742 12.297 12.852 13.407 13.963 14.518 21 22 23 24 25 26 B B 16.02 16.58 17.70 18.82 20.49 23.29 15.074 15.630 16.742 17.854 19.523 22.305 26.08 27.75 31.10 34.44 40.02 45.59 25.087 26.757 30.097 33.438 39.006 44.575 * Maximum bores shown will accommodate standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. These sprockets are furnished with minimum bore and no keyway. They can be rebored to size, keywayed and setscrewed for a reasonable extra charge. Steel Double Sprockets with Q-D® Bushings Table No. 3 DIAMETERS Part No. Bushing Bore Range Outside D140J35 D140J45 D140M60 J J M* 1 1/2 - 4 1/2” 1 1/2 - 4 1/2 2 - 5 1/2 20.49” 26.08 34.44 Pitch Type 19.523” QD-4 25.087 QD-4 33.438 QD-4 H Wt. Less Bushing 7 1/4” 7 1/4 9 169 288 370 DIMENSIONS No. Teeth T 35 45 60 .894” .894 .894 M OL L P C 2.818” 7 15/32” 4 5/8” 1 11/32” 19/32” 2.818 7 15/32 4 5/8 1 11/32 19/32 2.818 7 15/32 6 3/4 1 11/32 1 19/32 *Bushing mounts with capscrews on “B” side only. H-50 Roller Chain Sprockets 140-160 Steel Minimum Bore Double Sprockets Table No. 1 DIAMETERS Part No. Pitch No. Teeth Outside Type D140B13 D140B14 D140B15 D140B16 D140B17 8.15” 8.72 9.28 9.85 10.41 7.313” 7.864 8.417 8.970 9.524 13 14 15 16 17 D140B18 D140B19 D140B20 D140B21 D140B22 D140B23 10.98 11.54 12.10 12.66 13.22 13.78 10.078 10.632 11.187 11.742 12.297 12.852 D140B24 D140B25 D140B26 D140C35 D140C45 D140C60 14.34 14.90 15.46 20.49 26.08 34.44 13.407 13.963 14.518 19.523 25.087 33.438 BORE H Wt. Lbs. .894” .894 .894 .894 .894 DIMENSIONS L P Max. 2.818” 3 3/4” 15/16” 2.818 3 3/4 15/16 2.818 3 3/4 15/16 2.818 4 1 3/16 2.818 4 1 3/16 5” 5 1/2 6 1/2 7 7 1/4 31.0 36.9 44.6 55.1 61.0 4 3/4 4 3/4 4 3/4 4 3/4 4 3/4 4 3/4 .894 .894 .894 .894 .894 .894 2.818 2.818 2.818 2.818 2.818 2.818 4 4 4 4 4 4 1 3/16 1 3/16 1 3/16 1 3/16 1 3/16 1 3/16 7 1/4 7 1/4 7 1/4 7 1/4 7 1/4 7 1/4 67.4 74.1 81.2 88.7 96.6 105 4 3/4 4 3/4 4 3/4 5 5 6 7/16 .894 .894 .894 .894 .894 .894 2.818 2.818 2.818 2.818 2.818 2.818 4 4 4 6 6 6 1/4 1 3/16 1 3/16 1 3/16 1 19/32 1 19/32 1 19/32 7 1/4 7 1/4 7 1/4 7 1/2 7 1/2 9 3/8 114 123 132 260 410 410 Stock Max.* T DB DB DB DB DB 1 1/2” 1 1/2 1 1/2 1 1/2 1 1/2 2 15/16” 3 3/8 4 3/8 4 3/4 4 3/4 18 19 20 21 22 23 DB DB DB DB DB DB 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 24 25 26 35 45 60 DB DB DB DC DC DC 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 M * Maximum bores shown will accommodate standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. These sprockets are furnished with minimum bore and no keyway. They can be rebored to size, keywayed and setscrewed for a reasonable extra charge. Sprockets for HARDENED TEETH Standard Keyseats Bore Range Keyseat 3/4" — 7/8" 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 3 3/8 — 3 3/4 3 7/8 — 4 1/2 4 9/16 — 5 1/2 3/16” X 3/32” 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 7/8 x 7/16 1 x 1/2 1 1/4 x 5/8 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-51 , 2" Pitch ANSI Chain Steel Single Sprockets with Browning Split Taper® Bushings Table No. 2 Table No. 3 No. 160 C H 2 7/8” 1 31/32” 2 7/8 1 3/4 2 7/8 1 3/4 2 7/8 1 3/4 2 7/8 1 3/4 1/4” 1/16 1/16 1/16 1/16 5 3/8” 5 3/8 5 3/8 5 3/8 5 3/8 Wt. Less Bushing 10.8 14.2 15.5 18.5 21.6 3 9/64 3 9/64 3 9/64 3 9/64 5 5/32 2 7/8 2 7/8 2 7/8 2 7/8 4 7/8 1 3/4 1 3/4 1 3/4 1 3/4 1 23/32 1/16 1/16 1/16 1/16 2 5 3/8 5 3/8 5 3/8 5 3/8 5 3/8 25.0 28.0 31.9 35.9 51.0 1.156 1.156 1.156 1.156 1.156 5 5/32 5 5/32 5 5/32 5 5/32 5 5/32 4 7/8 4 7/8 4 7/8 4 7/8 4 7/8 1 23/32 1 23/32 1 23/32 1 23/32 1 23/32 2 2 2 2 2 5 3/8 5 3/8 5 3/8 5 3/8 5 3/8 56.0 60.0 65.0 71.5 74.0 6 6 6 6 6 6 1.156 1.156 1.156 1.156 1.156 1.156 5 5/32 7 1/8 5 5/32 7 1/8 5 5/32 7 1/8 4 7/8 6 3/4 4 7/8 6 3/4 4 7/8 6 3/4 1 23/32 2 23/32 1 23/32 2 23/32 1 23/32 2 23/32 2 2 7/8 2 2 7/8 2 2 7/8 5 3/8 6 3/8 5 3/8 6 3/8 5 3/8 6 3/8 79.0 79.0 99.8 99.8 106 115 6 6 6 6 6 6 1.156 7 1/8 1.156 7 1/8 1.156 7 1/8 1.156 5 25/32 1.156 5 25/32 1.156 7 19/32 6 3/4 6 3/4 6 3/4 5 1/4 5 1/4 7 1/8 2 23/32 2 7/8 2 23/32 2 7/8 2 23/32 2 7/8 1 21/32 1 15/16 1 21/32 1 15/16 2 19/32 2 7/8 6 3/8 6 3/8 6 3/8 8 3/8 8 3/8 8 3/8 150 165 204 354 308 684 DIAMETERS No. Type T OL Outside Pitch Teeth Nom. 8.01” 7.099” 11 4 1.156” 3 13/32” 8.66 7.727 12 4 1.156 3 9/64 9.31 8.357 13 4 1.156 3 9/64 9.96 8.988 14 4 1.156 3 9/64 10.61 9.620 15 4 1.156 3 9/64 Part No. Bushing Bore Range H160R11 H160R12 H160R13 H160R14 H160R15 R1 R1 R1 R1 R1 1 1/8 - 3 3/4” 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 H160R16 H160R17 H160R18 H160R19 H160R20 R1 R1 R1 R1 R2 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 3/8 - 3 5/8 11.25 11.90 12.54 13.19 13.83 10.252 10.882 11.518 12.151 12.785 16 17 18 19 20 4 4 4 4 6 1.156 1.156 1.156 1.156 1.156 H160R21 H160R22 H160R23 H160R24 H160R25 R2 R2 R2 R2 R2 1 3/8 - 3 5/8 1 3/8 - 3 5/8 1 3/8 - 3 5/8 1 3/8 - 3 5/8 1 3/8 - 3 5/8 14.47 15.11 15.75 16.39 17.03 13.419 14.053 14.688 15.323 15.958 21 22 23 24 25 6 6 6 6 6 H160R26 H120S26 H160R28 H160S28 H160R30 H160S30 R2 S2 R2 S2 R2 S2 1 3/8 - 3 5/8 1 7/8 - 4 3/16 1 3/8 - 3 5/8 1 7/8 - 4 3/16 1 3/8 - 3 5/8 1 7/8 - 4 3/16 17.67 17.67 18.95 18.95 20.23 20.23 16.593 16.593 17.863 17.863 19.134 19.134 26 26 28 28 30 30 160S35 160S40 160S45 160U60 160U70 160U80 S2 S2 S2 U0 U0 U1 1 7/8 - 4 3/16 1 7/8 - 4 3/16 1 7/8 - 4 3/16 2 3/8 - 5 1/2 2 3/8 - 5 1/2 2 3/8 - 5 1/2 23.42 26.61 29.80 39.36 45.73 52.10 22.312 25.491 28.671 38.215 44.578 50.943 35 40 45 60 70 80 DIMENSIONS L P Where two sprockets with the same number of teeth but different bushings are offered, we suggest using the one with the larger bushing for heavier service drives. Roller Chain Sprockets Sprockets for No. 160 , 2" Pitch ANSI Chain Steel Single Sprockets with Q-D® Bushings Table No. 1 HARDENED TEETH 160 OL L P C 12 13 14 15 T Nom. 1.156” 1.156 1.156 1.156 3 1/4” 3 1/4 3 1/4 4 3/8 2 3/4” 2 3/4 2 3/4 3 3/4 1 21/32” 1 21/32 1 21/32 2 23/32 - Wt. Less H Bushing 6” 13.9 6 16.3 6 18.5 6 5/8 26.3 QD-1 QD-1 QD-1 QD-1 QD-1 16 17 18 19 20 1.156 1.156 1.156 1.156 1.156 4 3/8 4 3/8 4 3/8 4 3/8 4 3/8 3 3/4 3 3/4 3 3/4 3 3/4 3 3/4 2 23/32 2 23/32 2 23/32 2 23/32 2 23/32 - 6 5/8 6 5/8 6 5/8 6 5/8 6 5/8 29.3 32.5 35.8 39.4 43.1 QD-1 QD-1 QD-1 QD-1 QD-1 21 22 23 24 25 1.156 1.156 1.156 1.156 1.156 4 3/8 4 3/8 4 3/8 4 3/8 4 3/8 3 3/4 3 3/4 3 3/4 3 3/4 3 3/4 2 23/32 2 23/32 2 23/32 2 23/32 2 23/32 - 6 5/8 6 5/8 6 5/8 6 5/8 6 5/8 47.0 51.2 55.5 60.0 64.7 1 1/2 - 4 1/2 17.67 1 1/2 - 4 1/2 18.95 1 1/2 - 4 1/2 20.23 16.593 QD-2 17.863 QD-2 19.134 QD-2 26 28 30 1.156 1.156 1.156 5 5/16 5 5/16 5 5/16 4 5/8 4 5/8 4 5/8 1 9/16 2 1/32” 1 9/16 2 1/32 1 9/16 2 1/32 7 1/4 7 1/4 7 1/4 74.2 84.5 95.6 1 1/2 - 4 1/2 23.42 2 - 5 1/2 26.61 22.312 QD-2 25.491 QD-3 35 40 1.156 5 5/16 4 5/8 1.156 7 15/32 6 3/4 1 9/16 3 7/32 2 1/32 2 7/16 7 1/4 9 127 186 28.671 QD-3 34.397 QD-3 38.215 QD-3 45 54 60 1.156 7 15/32 6 3/4 1.156 7 15/32 6 3/4 1.156 7 15/32 6 3/4 3 7/32 3 7/32 3 7/32 2 7/16 2 7/16 2 7/16 9 9 9 227 295 360 Part No. Bushing Bore Range H160E12 H160E13 H160E14 H160F15 E E E F H160F16 H160F17 H160F18 H160F19 H160F20 F F F F F 1 -4 1 -4 1 -4 1 -4 1 -4 H160F21 H160F22 H160F23 H160F24 H160F25 F F F F F 1 -4 1 -4 1 -4 1 -4 1 -4 H160J26 H160J28 H160J30 J J J 160J35 160M40* J M 160M45* 160M54* 160M60* M M M DIAMETERS Type No. Teeth 7.727” 8.357 8.988 9.620 QD-1 QD-1 QD-1 QD-1 11.26 11.90 12.54 13.19 13.83 10.252 10.885 11.518 12.151 12.785 14.47 15.11 15.75 16.39 17.03 13.419 14.053 14.688 15.323 15.958 Outside Pitch 7/8 - 3 1/2” 8.66” 7/8 - 3 1/2 9.31 7/8 - 3 1/2 9.96 1 -4 10.61 2 - 5 1/2 2 - 5 1/2 2 - 5 1/2 29.80 35.54 39.36 DIMENSIONS *Bushing mounts with capscrews on “B” side only. Standard Keyseats Table No. 3 Type "A" Steel Plate Sprockets Table No. 2 Part No. Outside Dia. Pitch No. Stock Dia. Teeth Bore T (Nom.) Wt. Lbs. Part No. Outside Dia. Pitch Dia. 160A8 160A9 160A10 160A11 160A12 6.03” 6.70 7.36 8.01 8.66 5.226” 5.848 6.472 7.099 7.727 8 9 10 11 12 1 1/2” 160A13 160A14 160A15 160A16 160A17 9.31 9.96 10.61 11.25 11.90 8.357 8.988 9.620 10.252 10.885 160A18 160A19 160A20 160A21 160A22 12.54 13.19 13.83 14.47 15.11 11.518 12.151 12.785 13.419 14.053 No. Stock Teeth Bore T (Nom.) Wt. Lbs. 1 1/2 1 1/2 1 1/2 1.156” 1.156 1.156 1.156 1.156 5.1 6.8 8.5 10.5 12.6 160A23 160A24 160A25 160A26 160A27 15.75” 16.39 17.03 17.67 18.31 14.688” 15.323 15.958 16.593 17.228 23 24 25 26 27 1 1/2” 1 1/2 1 1/2 1 1/2 1 1/2 1.156” 1.156 1.156 1.156 1.156 51.0 55.5 64.9 66.5 71.0 13 14 15 16 17 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1.156 1.156 1.156 1.156 1.156 15.3 17.7 20.7 23.9 27.0 160A28 160A30 160A35 160A40 160A45 18.95 20.23 23.42 26.61 29.80 17.863 19.134 22.312 25.491 28.671 28 30 35 40 45 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1.156 1.156 1.156 1.156 1.156 76.0 88.0 127 155 210 18 19 20 21 22 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1.156 1.156 1.156 1.156 1.156 31.3 34.6 39.3 43.1 48.4 160A54 160A60 160A70 160A80 35.54 39.36 45.73 52.10 34.397 38.215 44.578 50.943 54 60 70 80 1 1/2 1 1/2 1 1/2 1 1/2 1.156 1.156 1.156 1.156 298 368 499 628 Bore Range Keyseat 3/4" — 7/8" 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 3 3/8 — 3 3/4 3 7/8 — 4 1/2 4 5/8 — 5 1/2 5 5/8 — 6 1/2 3/16” X 3/32” 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 7/8 x 7/16 1 x 1/2 1 1/4 x 5/8 1 1/2 x 3/4 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-52 160 Roller Chain Sprockets Steel Minimum Bore Single Sprockets Table No. 1 DIAMETERS DIMENSIONS L P Max. 2 1/4” 1 3/32” 2 1/4 1 3/32 2 1/4 1 3/32 2 1/2 1 11/32 2 1/2 1 11/32 H Wt. Lbs. 2 1/4” 2 3/8 2 3/4 3 1/4 3 3/4 T Nom. 1.156” 1.156 1.156 1.156 1.156 3 1/4” 3 5/8 4 1/8 4 3/4 5 1/2 8.5 10.9 13.8 18.4 23.1 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 4 4 1/2 5 1/4 5 1/4 5 1/4 1.156 1.156 1.156 1.156 1.156 2 5/8 2 5/8 2 5/8 2 3/4 2 3/4 1 15/32 1 15/32 1 15/32 1 19/32 1 19/32 6 6 1/2 7 7 7 28.4 33.2 38.5 43.0 46.4 B B B B B 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 5 1/4 5 1/4 5 1/4 5 1/4 5 1/4 1.156 1.156 1.156 1.156 1.156 2 3/4 2 3/4 2 3/4 2 3/4 2 3/4 1 19/32 1 19/32 1 19/32 1 19/32 1 19/32 7 7 7 7 7 1/8 50.1 53.9 58.0 62.3 67.4 23 24 25 26 27 B B B B B 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 5 1/4 5 1/4 5 1/4 5 1/4 5 1/4 1.156 1.156 1.156 1.156 1.156 2 3/4 2 15/16 2 15/16 2 15/16 2 15/16 1 19/32 1 25/32 1 25/32 1 25/32 1 25/32 7 1/8 7 1/8 7 1/8 7 1/8 7 1/8 72.0 79.0 84.1 89.4 94.9 17.863 19.134 22.312 25.491 28.671 28 30 35 40 45 B B C C C 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 5 1/4 5 1/4 5 1/2 5 1/2 5 1/2 1.156 1.156 1.156 1.156 1.156 2 15/16 2 15/16 4 1/4 4 1/4 4 1/4 1 25/32 1 25/32 1 35/64 1 35/64 1 35/64 7 1/8 7 1/8 8 8 8 100.6 112.7 169.8 208.8 253.1 34.397 38.215 44.578 50.943 54 60 70 80 C C C C 1 1/2 1 1/2 1 1/2 1 1/2 5 1/2 5 1/2 5 1/2 5 1/2 1.156 1.156 1.156 1.156 5 5 5 5 1/2 1 59/64 1 59/64 1 59/64 2 11/64 8 8 8 9 356.2 427.4 562.8 742.3 Part No. Outside Pitch No. Teeth Type 160B8 160B9 160B10 160B11 160B12 6.03” 6.70 7.36 8.01 8.66 5.226” 5.848 6.472 7.099 7.727 8 9 10 11 12 160B13 160B14 160B15 160B16 160B17 9.31 9.96 10.61 11.25 11.90 8.357 8.988 9.620 10.252 10.885 160B18 160B19 160B20 160B21 160B22 12.54 13.19 13.83 14.47 15.11 160B23 160B24 160B25 160B26 160B27 BORE Stock Max.* B B B B B 1 1/2” 1 1/2 1 1/2 1 1/2 1 1/2 13 14 15 16 17 B B B B B 11.518 12.151 12.785 13.419 14.053 18 19 20 21 22 15.75 16.39 17.03 17.67 18.31 14.688 15.323 15.958 16.593 17.228 160B28 160B30 160C35 160C40 160C45 18.95 20.23 23.42 26.61 29.80 160C54 160C60 160C70 160C80 35.54 39.36 45.73 52.10 * Maximum bores shown will accommodate standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. These sprockets are furnished with minimum bore and no keyway. They can be rebored to size, keywayed and setscrewed for a reasonable extra charge. Steel Double Sprockets with Q-D® Bushings Table No. 2 Part No. Bushing D160M35* D160N45* D160N60* M N N Bore Range DIAMETERS Outside Pitch Type No. Teeth DIMENSIONS T M OL L P C H 2 - 5 1/2” 23.42” 22.312” QD-4 35 1.119” 3.424” 7 15/32” 6 3/4” 2 15/64” 1 5/32” 9” 2 7/16 - 5 7/8 29.80 28.671 QD-4 45 1.119 3.424 9 1/8 8 1/8 2 3/4 2 11/64 10 2 7/16 - 5 7/8 39.36 38.215 QD-4 60 1.119 3.424 9 1/8 8 1/8 2 3/4 2 11/64 10 Wt. Less Bushing 343 384 570 *Bushing mounts with capscrews on “B” side only. Steel Minimum Bore Double Sprockets Table No. 3 DIAMETERS Part No. Outside D160B13 D160B14 D160B15 D160B16 D160B17 Pitch No. of Teeth Type 9.31 9.96 10.61 11.26 11.90 8.357 8.988 9.620 10.252 10.885 13 14 15 16 17 D160B18 D160B19 D160B20 D160B21 12.54 13.19 13.83 14.47 11.518 12.151 12.785 13.419 D160B22 D160B23 D160B24 D160B25 15.11 15.75 16.39 17.03 D160B26 D160C35 D160C45 D160C60 17.67 23.42 29.80 39.36 BORE DIMENSIONS Stock Max.* T M L Max. P H Wt. (lbs.) DB DB DB DB DB 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 4 4 3/4 5 1/4 5 1/4 5 1/4 1.119 1.119 1.119 1.119 1.119 3.424 3.424 3.424 3.424 3.424 4 3/4 4 3/4 4 3/4 4 3/4 4 3/4 1 21/64 1 21/64 1 21/64 1 21/64 1 21/64 6 6 3/4 7 3/8 7 3/8 7 3/8 52.7 63.2 74.0 82.9 92.4 18 19 20 21 DB DB DB DB 1 1/2 1 1/2 1 1/2 1 1/2 5 1/4 5 1/4 5 7/16 5 7/16 1.119 1.119 1.119 1.119 3.424 3.424 3.424 3.424 4 3/4 4 3/4 4 3/4 4 3/4 1 21/64 1 21/64 1 21/64 1 21/64 7 3/8 7 3/8 7 3/4 7 3/4 102 113 126 138 14.053 14.688 15.323 15.958 22 23 24 25 DB DB DB DB 1 1/2 1 1/2 1 1/2 1 1/2 5 7/16 5 7/16 5 7/16 5 7/16 1.119 1.119 1.119 1.119 3.424 3.424 3.424 3.424 4 3/4 4 3/4 4 3/4 4 3/4 1 21/64 1 21/64 1 21/64 1 21/64 7 3/4 7 3/4 7 3/4 7 3/4 151 164 176 192 16.593 22.312 28.671 38.215 26 35 45 60 DB DC DC DC 1 1/2 1 1/2 1 1/2 1 1/2 5 7/16 6 3/4 7 7 1.119 1.119 1.119 1.119 3.424 3.424 3.424 3.424 4 3/4 6 5/8 7 1/8 7 1/8 1 21/64 1 19/32 1 27/32 1 27/32 7 3/4 9 3/4 10 10 207 419 458 611 * Maximum bores shown will accommodate standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. These sprockets are furnished with minimum bore and no keyway. They can be rebored to size, keywayed and setscrewed for a reasonable extra charge. H-53 Roller Chain Sprockets Sprockets for 200 No. 200 , 2 1/2" Pitch ANSI Chain Steel Single Sprockets for Browning Split Taper® Bushings Table No. 1 C H 12 13 14 15 DIMENSIONS T OL L P Nom. 1.389” 5 5/32” 4 7/8” 1 1/2” 1.389 7 1/8 6 3/4 2 1/2 1.389 7 1/8 6 3/4 2 1/2 1.389 7 1/8 6 3/4 2 1/2 2” 2 7/8 2 7/8 2 7/8 5 3/8” 6 3/8 6 3/8 6 3/8 Wt. Less Bushing 35.3 52.2 57.5 61.0 6 6 6 6 16 17 18 19 1.389 7 1/8 1.389 7 1/8 1.389 5 23/32 1.389 5 23/32 6 3/4 2 1/2 6 3/4 2 1/2 5 1/4 2 17/32 5 1/4 2 17/32 2 7/8 2 7/8 1 5/8 1 5/8 6 3/8 6 3/8 8 3/8 8 3/8 71.0 79.0 76.5 83.7 15.982 16.775 17.567 18.360 6 6 6 6 20 21 22 23 1.389 1.389 1.389 1.389 5 23/32 5 23/32 5 23/32 5 23/32 5 1/4 5 1/4 5 1/4 5 1/4 2 17/32 2 17/32 2 17/32 2 17/32 1 5/8 1 5/8 1 5/8 1 5/8 8 3/8 8 3/8 8 3/8 8 3/8 91.3 99.4 110 117 20.49 21.29 22.09 23.69 25.29 19.152 19.947 20.740 22.330 23.917 6 6 6 6 6 24 25 26 28 30 1.389 1.389 1.389 1.389 1.389 5 23/32 5 23/32 5 23/32 5 23/32 5 23/32 5 1/4 5 1/4 5 1/4 5 1/4 5 1/4 2 17/32 2 17/32 2 17/32 2 17/32 2 17/32 1 5/8 1 5/8 1 5/8 1 5/8 1 5/8 8 3/8 8 3/8 8 3/8 8 3/8 8 3/8 126 140 150 169 188 26.88 29.28 33.27 37.25 44.42 49.20 25.505 27.890 31.865 35.840 42.995 47.767 6 6 6 6 6 6 32 35 40 45 54 60 1.389 1.389 1.389 1.389 1.389 1.389 5 23/32 7 19/32 7 19/32 7 19/32 10 19/32 10 19/32 5 1/4 2 17/32 7 1/8 2 7/8 7 1/8 2 7/8 7 1/8 2 7/8 10 1/8 3 29/32 10 1/8 3 29/32 1 5/8 2 7/8 2 7/8 2 7/8 4 1/4 4 1/4 8 3/8 8 3/8 8 3/8 8 3/8 8 3/8 8 3/8 212 252 306 290 385 445 DIAMETERS Part No. Bushing Bore Range Type No. Teeth 200R12 200S13 200S14 200S15 R2 S2 S2 S2 1 3/8 - 3 5/8” 1 7/8 - 4 3/16 1 7/8 - 4 3/16 1 7/8 - 4 3/16 10.83” 9.660” 11.64 10.447 12.46 11.235 13.26 12.025 6 6 6 6 200S16 200S17 200U18 200U19 S2 S2 U0 U0 1 7/8 - 4 3/16 1 7/8 - 4 3/16 2 3/8 - 5 1/2 2 3/8 - 5 1/2 14.07 14.87 15.68 16.48 12.815 13.605 14.397 15.190 200U20 200U21 200U22 200U23 U0 U0 U0 U0 2 3/8 - 5 1/2 2 3/8 - 5 1/2 2 3/8 - 5 1/2 2 3/8 - 5 1/2 17.29 18.09 18.89 19.69 200U24 200U25 200U26 200U28 200U30 U0 U0 U0 U0 U0 2 3/8 - 5 1/2 2 3/8 - 5 1/2 2 3/8 - 5 1/2 2 3/8 - 5 1/2 2 3/8 - 5 1/2 200U32 200U35 200U40 200U45 200U54 200U60 U0 U1 U1 U1 U2 U2 2 3/8 - 5 1/2 2 3/8 - 5 1/2 2 3/8 - 5 1/2 2 3/8 - 5 1/2 2 7/16 - 5 2 7/16 - 5 Outside Pitch Steel Single Sprockets with Q-D® Bushings Table No. 2 DIAMETERS Bushing Bore Range 200F12 200J13 200J14 200J15 F J J J 1 - 4” 1 1/2 - 4 1/2 1 1/2 - 4 1/2 1 1/2 - 4 1/2 10.83” 9.660” QD-2 12 11.64 10.447 QD-2 13 12.46 11.235 QD-2 14 13.26 12.025 QD-2 15 T Nom. 1.389” 1.389 1.389 1.389 200J16S* 200M17* 200M18* J M M 1 1/2 - 4 1/2 2 - 5 1/2 2 - 5 1/2 14.07 14.87 15.68 12.815 QD-2 16 13.605 QD-3 17 14.397 QD-3 18 200M21* 200M24* M M 2 - 5 1/2 2 - 5 1/2 18.09 20.49 200M25* 200M26* 200M28* M M M 2 - 5 1/2 2 - 5 1/2 2 - 5 1/2 200M35* 200M40* 200N45* 200N54* M M N N 2 - 5 1/2 2 - 5 1/2 2 7/16 - 5 7/8 2 7/16 - 5 7/8 Type No. Teeth DIMENSIONS Part No. Wt. Less Bushing 29.9 38.9 44.1 48.9 OL L P C H 4 3/8” 7 1/4 7 1/4 7 1/4 3 3/4” 4 5/8 4 5/8 4 5/8 1 3/8” 1 9/16 1 9/16 1 9/16 1 7/64” 1 51/64 1 51/64 1 51/64 6 5/8” 7 1/4 7 1/4 7 1/4 1.389 7 1/4 1.389 7 15/32 1.389 7 15/32 4 5/8 6 3/4 6 3/4 1 9/16 1 51/64 7 1/4 3 1/8 2 19/64 9 3 1/8 2 19/64 9 54.8 83.2 89.8 16.775 QD-3 21 19.152 QD-3 24 1.389 7 15/32 1.389 7 15/32 6 3/4 6 3/4 3 1/8 3 1/8 2 19/64 2 19/64 9 9 112 138 21.29 22.09 23.69 19.947 QD-3 25 20.740 QD-3 26 22.330 QD-3 28 1.389 7 15/32 1.389 7 15/32 1.389 7 15/32 6 3/4 6 3/4 6 3/4 3 1/8 3 1/8 3 1/8 2 19/64 2 19/64 2 19/64 9 9 9 147 157 177 29.28 33.27 37.25 44.42 27.890 31.865 35.840 42.995 1.389 7 15/32 1.389 7 15/32 1.389 9 1/8 1.389 9 1/8 6 3/4 6 3/4 8 1/8 8 1/8 3 1/8 3 1/8 3 25/32 3 25/32 2 19/64 2 19/64 3 11/64 3 11/64 9 9 10 10 261 310 322 414 Outside Pitch QD-3 QD-3 QD-3 QD-3 35 40 45 54 *Bushing mounts with capscrews on “B” side only. Standard Keyseats Table No. 3 Bore Range Keyseat 15/16" — 1 1/4" 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 3 3/8 — 3 3/4 3 7/8 — 4 1/2 4 5/8 — 5 1/2 5 5/8 — 6 1/2 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 7/8 x 7/16 1 x 1/2 1 1/4 x 5/8 1 1/2 x 3/4 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-54 Roller Chain Sprockets 200 Type "A" Steel Plate Sprockets Table No. 1 DIAMETERS Part No. No. of Stock Pitch Teeth Bore Outside 200A10 200A11 200A12 200A13 9.20 10.02 10.83 11.64 8.090 8.872 9.660 10.447 10 11 12 13 200A14 200A15 200A16 200A17 12.46 13.26 14.07 14.87 11.235 12.025 12.815 13.605 200A18 200A19 200A20 200A21 200A22 15.68 16.48 17.29 18.09 18.89 14.397 15.190 15.982 16.775 17.567 DIAMETERS T Nom. Wt. (lbs.) Part No. Outside Pitch No. of Teeth Stock Bore T Nom. Wt. (lbs.) 1 1/2 1 1/2 1 1/2 1 1/2 1.389 1.389 1.389 1.389 17.4 21.3 27.5 32.4 200A23 200A24 200A25 200A26 19.69 20.49 21.29 22.09 18.360 19.152 19.947 20.740 23 24 25 26 1 1/2 1 1/2 1 1/2 1 1/2 1.389 1.389 1.389 1.389 101 110 119 130 14 15 16 17 1 1/2 1 1/2 1 1/2 1 1/2 1.389 1.389 1.389 1.389 37.6 42.9 48.8 55.1 200A28 200A30 200A32 200A35 23.69 25.29 26.88 29.28 22.330 23.917 25.505 27.890 28 30 32 35 1 1/2 1 1/2 1 1/2 1 1/2 1.389 1.389 1.389 1.389 150 172 196 234 18 19 20 21 22 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 1.389 1.389 1.389 1.389 1.389 61.8 68.9 76.6 84.6 92.1 200A40 200A45 200A54 200A60 33.27 37.25 44.42 49.20 31.865 35.840 42.995 47.767 40 45 54 60 1 1/2 1 1/2 1 1/2 1 1/2 1.389 1.389 1.389 1.389 307 390 563 776 Steel Minimum Bore Single Sprockets Table No. 2 DIAMETERS Part No. Pitch No. Teeth Type Outside 200B10 200B11 200B12 200B13 200B14 9.20” 10.02 10.83 11.64 12.46 8.090” 8.872 9.660 10.447 11.235 10 11 12 13 14 200B15 200B16 200B17 200B18 200B19 13.26 14.07 14.87 15.68 16.48 12.025 12.815 13.605 14.397 15.190 200B20 200B21 200B22 200B23 200B24 17.29 18.09 18.89 19.69 20.49 200B25 200C26 200C28 200C30 200C32 200C35 200C40 200B45 200C54 200C60 BORE DIMENSIONS L P Max. 3” 1 39/64” 3 1 39/64 3 1 39/64 3 1 39/64 3 1/2 2 7/64 H Wt. Lbs 5 1/2” 6 1/4 6 5/8 7 1/8 7 5/8 29.5 35.7 43.0 50.4 64.5 2 7/64 2 7/64 2 7/64 2 7/64 2 7/64 8 8 8 8 8 72.9 79.0 85.4 92.3 99.5 3 1/2 3 1/2 4 4 4 2 7/64 2 7/64 2 39/64 2 39/64 2 39/64 8 8 8 1/2 8 1/2 8 1/2 107 115 135 144 153 1.389 1.389 1.389 1.389 1.389 4 4 1/2 4 1/2 4 1/2 4 1/2 2 39/64 1 9/16 1 9/16 1 9/16 1 9/16 8 1/2 8 1/2 8 1/2 8 1/2 8 1/2 163 181 202 224 249 1.389 1.389 1.389 1.389 1.389 4 1/2 5 5 5 1/2 5 1/2 1 9/16 1 13/16 1 13/16 2 1/16 2 1/16 8 1/2 9 9 9 1/2 9 1/2 288 376 459 651 784 Stock Max.* B B B B B 1 1/2” 1 1/2 1 1/2 1 1/2 1 1/2 3 3/4” 4 1/4 4 1/2 5 1/4 5 3/8 T Nom. 1.389” 1.389 1.389 1.389 1.389 15 16 17 18 19 B B B B B 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 5 1/2 5 1/2 5 1/2 5 1/2 5 1/2 1.389 1.389 1.389 1.389 1.389 3 1/2 3 1/2 3 1/2 3 1/2 3 1/2 15.982 16.775 17.567 18.360 19.152 20 21 22 23 24 B B B B 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 5 1/2 5 1/2 5 3/4 5 3/4 5 3/4 1.389 1.389 1.389 1.389 1.389 21.29 22.09 23.69 25.29 26.88 19.947 20.740 22.330 23.917 25.505 25 26 28 30 32 B C C C C 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 5 3/4 5 3/4 5 3/4 5 3/4 5 3/4 29.28 33.27 37.25 44.42 49.20 27.890 31.865 35.840 42.995 47.767 35 40 45 54 60 C C C C C 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 5 3/4 6 6 6 1/2 6 1/2 * Maximum bores shown will accommodate standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. These sprockets are furnished with minimum bore and no keyway. They can be rebored to size, keywayed and setscrewed for a reasonable extra charge. Steel Minimum Bore Double Sprockets Table No. 3 H-55 DIAMETERS Part No. Outside Pitch No. Teeth Type D200B11 D200B12 D200B13 D200B14 D200B15 10.02 10.83 11.64 12.46 13.26 8.872 9.660 10.447 11.235 12.025 11 12 13 14 15 D200B16 D200B17 D200B18 D200B19 D200B20 14.07 14.87 15.68 16.48 17.29 12.815 13.605 14.397 15.190 15.932 D200B21 D200B22 D200B23 D200B24 D200B25 18.09 18.89 19.69 20.49 21.29 D200B26 D200C45 D200C60 22.09 37.25 49.20 BORE DIMENSIONS Stock Max.* T M L Max. P H Wt. (lbs.) DB DB DB DB DB 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 4 4 1/2 5 5/16 5 9/16 5 7/8 1.344 1.344 1.344 1.344 1.344 4.161 4.161 4.161 4.161 4.161 5 7/8 6 1/4 6 3/8 6 3/8 6 3/8 1 23/32 2 3/32 2 7/32 2 7/32 2 7/32 6 6 5/8 7 1/4 8 1/4 8 3/4 69.6 88.0 107 129 149 16 17 18 19 20 DB DB DB DB DB 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 5 7/8 5 7/8 5 7/8 5 7/8 5 7/8 1.344 1.344 1.344 1.344 1.344 4.161 4.161 4.161 4.161 4.161 6 5/8 6 5/8 6 5/8 6 5/8 6 5/8 2 15/32 2 15/32 2 15/32 2 15/32 2 15/32 8 3/4 8 3/4 8 3/4 8 3/4 8 3/4 170 188 207 227 248 16.775 17.567 18.360 19.152 19.947 21 22 23 24 25 DB DB DB DB DB 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 5 7/8 5 7/8 5 7/8 5 7/8 5 7/8 1.344 1.344 1.344 1.344 1.344 4.161 4.161 4.161 4.161 4.161 6 5/8 6 5/8 6 5/8 6 5/8 6 5/8 2 15/32 2 15/32 2 15/32 2 15/32 2 15/32 8 3/4 8 3/4 8 3/4 8 3/4 8 3/4 272 295 320 346 374 20.740 35.840 47.767 26 45 60 DB DC DC 1 1/2 1 1/2 1 1/2 5 7/8 7 7 1.344 1.344 1.344 4.161 4.161 4.161 6 5/8 8 1/2 8 1/2 2 15/32 2 11/64 2 11/64 8 3/4 10 10 402 663 929 * Maximum bores shown will accommodate standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway, shallow keyway or setscrew at angle to keyway. These sprockets are furnished with minimum bore and no keyway. They can be rebored to size, keywayed and setscrewed for a reasonable extra charge. Taper Bore Sprockets Sprockets for Table No. 1 Part No. 35TB18 35TB19 35TB20 35TB21 35TB22 No. 35 , 3/8" Pitch ANSI Chain Diameter Bore Bushing Range Outside Pitch 1008 1/2 - 1 2.35 2.160 1008 1/2 - 1 2.47 2.278 1008 1/2 - 1 2.59 2.397 1008 1/2 - 1 2.71 2.516 1210 1/2 - 1 1/4 2.83 2.635 No. of Teeth. 18 19 20 21 22 L H 1 1 1 1 1 T (Nom.) .168 .168 .168 .168 .168 7/8 7/8 7/8 7/8 1 1 7/8 1 13/16 1 15/16 2 1/16 2 3/8 Wt. Lbs less Bush. 0.4 0.5 0.6 0.7 0.8 Type 35TB23 35TB24 35TB25 35TB26 35TB28 1210 1210 1210 1610 1610 1/2 - 1 1/4 1/2 - 1 1/4 1/2 - 1 1/4 1/2 - 1 5/8 1/2 - 1 5/8 2.95 3.07 3.19 3.31 3.55 2.754 2.873 2.992 3.111 3.349 23 24 25 26 28 1 1 1 1 1 .168 .168 .168 .168 .168 1 1 1 1 1 2 7/16 2 7/16 2 7/16 2 7/8 3 0.9 0.9 1.2 1.1 1.2 35TB30 35TB32 35TB35 35TB36 35TB40 1610 1610 1610 1610 1610 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 3.79 4.03 4.39 4.51 4.99 3.588 3.826 4.183 4.303 4.780 30 32 35 36 40 1 1 1 1 1 .168 .168 .168 .168 .168 1 1 1 1 1 3 3 3 3 3 1.2 1.3 1.4 1.4 1.9 35TB42 35TB45 35TB48 35TB54 35TB60 1610 1610 1610 1610 1610 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 5.23 5.59 5.95 6.66 7.38 5.018 5.376 5.734 6.449 7.165 42 45 48 54 60 1 1 1 1 1 .168 .168 .168 .168 .168 1 1 1 1 1 3 3 3 3 3 2.0 2.1 2.3 2.6 3.0 35TB70 35TB72 35TB80 35TB84 35TB96 35TB112 1610 1610 1610 1610 1610 1610 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 8.58 8.81 9.77 10.25 11.68 13.59 8.358 8.597 9.552 10.029 11.461 13.371 70 72 80 84 96 112 1 1 1 1 1 1 .168 .168 .168 .168 .168 .168 1 1 1 1 1 1 3 3 3 3 3 3 3.7 3.9 4.5 4.9 6.0 7.8 D35TB19 D35TB20 D35TB21 D35TB22 D35TB24 1008 1008 1008 1008 1210 1/2 - 1 1/2 - 1 1/2 - 1 1/2 - 1 1/2 - 1 1/4 2.47 2.59 2.71 2.83 3.07 2.278 2.397 2.516 2.635 2.873 19 20 21 22 24 2 2 2 2 2 .162 .162 .162 .162 .162 7/8 7/8 7/8 7/8 1 1 53/64 1 15/16 2 1/16 2 3/16 2 7/16 0.6 0.8 1.4 1.7 1.8 D35TB26 D35TB30 D35TB32 D35TB35 D35TB40 1210 1610 1610 1610 1610 1/2 - 1 1/4 1/2 - 5/8 1/2 - 5/8 1/2 - 5/8 1/2 - 5/8 3.31 3.79 4.03 4.39 4.99 3.111 3.588 3.826 4.183 4.780 26 30 32 35 40 2 2 2 2 2 .162 .162 .162 .162 .162 1 1 1 1 1 2 5/8 3 1/8 3 1/4 3 1/4 3 1/4 2.0 1.8 2.0 2.3 2.9 D35TB45 D35TB48 D35TB54 D35TB60 D35TB70 1610 1610 1610 1610 1610 1/2 - 5/8 1/2 - 5/8 1/2 - 5/8 1/2 - 5/8 1/2 - 5/8 5.59 5.95 6.66 7.38 8.58 5.376 5.734 6.449 7.165 8.358 45 48 54 60 70 2 2 2 2 2 .162 .162 .162 .162 .162 1 1 1 1 1 3 1/4 3 5/8 3 5/8 3 5/8 3 5/8 3.2 3.1 3.9 4.9 6.3 D35TB80 D35TB96 D35TB112 1610 1610 1610 1/2 - 5/8 1/2 - 5/8 1/2 - 5/8 9.77 11.68 13.59 9.552 11.461 13.371 80 96 112 2 2 2 .162 .162 .162 1 1 1 3 5/8 3 5/8 3 5/8 7.9 9.9 10.9 Steel Double Sprockets HARDENED TEETH Table No. 2 Sprockets for Table No. 3 Part No. 41TB14 41TB15 41TB16 41TB17 41TB18 No. 41 , 1/2" Pitch ANSI Chain Diameter Bore Bushing Range Outside Pitch 1008 1/2 - 1 2.49 2.247 1008 1/2 - 1 2.65 2.405 1008 1/2 - 1 2.81 2.563 1210 1/2 - 1 1/4 2.97 2.721 1210 1/2 - 1 1/4 3.14 2.879 No. of Teeth. 14 15 16 17 18 L H 1 1 1 1 1 T (Nom.) .227 .227 .227 .227 .227 7/8 7/8 7/8 1 1 1 7/8 1 7/8 2 2 3/8 2 3/8 Wt. Lbs less Bush. 0.4 0.5 0.6 0.7 0.9 Type 41TB19 41TB20 41TB21 41TB22 41TB23 1210 1610 1610 1610 1610 1/2 - 1 1/4 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 3.30 3.46 3.62 3.78 3.94 3.038 3.196 3.355 3.513 3.672 19 20 21 22 23 1 1 1 1 1 .227 .227 .227 .227 .227 1 1 1 1 1 2 1/2 2 7/8 3 3 3 1.1 1.1 1.2 1.3 1.4 41TB24 41TB25 41TB26 41TB28 41TB30 1610 1610 1610 1610 1610 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 4.10 4.26 4.42 4.74 5.06 3.831 3.989 4.148 4.466 4.783 24 25 26 28 30 1 1 1 1 1 .227 .227 .227 .227 .227 1 1 1 1 1 3 1/4 3 1/4 3 1/4 3 1/4 3 1/4 1.4 1.5 1.7 1.7 1.8 41TB32 41TB35 41TB36 41TB40 41TB45 1610 1610 1610 1610 1610 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 5.38 5.86 6.02 6.65 7.45 5.101 5.578 5.737 6.373 7.168 32 35 36 40 45 1 1 1 1 1 .227 .227 .227 .227 .227 1 1 1 1 1 3 1/4 3 3 3 3 1.9 2.3 2.4 2.7 3.5 41TB48 41TB54 41TB60 41TB70 41TB72 1610 1610 1610 1610 1610 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 7.93 8.88 9.84 11.43 11.75 7.645 8.599 9.554 11.145 11.463 48 54 60 70 72 1 1 1 1 1 .227 .227 .227 .227 .227 1 1 1 1 1 3 3 3 3 3 4.1 4.9 5.7 7.4 8.2 41TB80 41TB96 1610 1610 1/2 - 1 5/8 1/2 - 1 5/8 13.03 15.57 12.736 15.282 80 96 1 1 .227 .227 1 1 3 3 9.6 13.1 H-56 Taper Bore Sprockets HARDENED TEETH No. 40 Sprockets for Table No. 1 , 1/2" Pitch ANSI Chain Pitch No. of Teeth Type T Nom. L H 2.247 2.405 2.563 2.721 2.879 14 15 16 17 18 1 1 1 1 1 .284 .284 .284 .284 .284 7/8 7/8 7/8 1 1 1 13/16 1 13/16 1 15/16 2 3/8 2 15/32 Wt. Lbs. Less Bush. 0.3 0.4 0.5 0.3 0.4 3.30 3.46 3.62 3.78 3.94 3.038 3.196 3.355 3.513 3.672 19 20 21 22 23 1 1 1 1 1 .284 .284 .284 .284 .284 1 1 1 1 1 2 15/32 2 25/32 2 25/32 2 25/32 3 0.7 0.6 0.8 0.8 0.9 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 4.10 4.26 4.42 4.74 5.06 3.831 3.989 4.148 4.466 4.783 24 25 26 28 30 1 1 1 1 1 .284 .284 .284 .284 .284 1 1 1 1 1 3 1/4 3 1/4 3 1/4 3 3 1.0 1.1 1.1 1.4 1.6 1610 1610 1610 1610 1610 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 5.38 5.86 6.02 6.65 6.97 5.101 5.578 5.737 6.373 6.691 32 35 36 40 42 1 1 1 1 1 .284 .284 .284 .284 .284 1 1 1 1 1 3 3 3 3 3 1.8 2.0 2.1 2.5 2.7 40TB45 40TB48 40TB54 40TB60 40TB70 1610 1610 1610 1610 2012 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 2 7.45 7.93 8.88 9.84 11.43 7.168 7.645 8.599 9.554 11.145 45 48 54 60 70 1 1 1 1 1 .284 .284 .284 .284 .284 1 1 1 1 1 1/4 3 3 3 3 3 7/8 3.1 4.1 5.0 6.0 7.3 40TB72 40TB80 40TB84 40TB96 40TB112 2012 2012 2012 2012 2517 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 1/2 11.75 13.03 13.66 15.57 18.12 11.463 12.736 13.372 15.282 17.828 72 80 84 96 112 1 1 1 1 1 .284 .284 .284 .284 .284 1 1/4 1 1/4 1 1/4 1 1/4 1 3/4 3 7/8 3 7/8 3 7/8 3 7/8 4 5/8 7.5 8.3 10.2 15.3 21.5 Diameter Part No. Bushing Bore Range Outside H40TB14 H40TB15 H40TB16 H40TB17 H40TB18 1008 1008 1008 1210 1210 1/2 - 1 1/2 - 1 1/2 - 1 1/2 - 1 1/4 1/2 - 1 1/4 2.49 2.65 2.81 2.97 3.14 H40TB19 H40TB20 H40TB21 H40TB22 H40TB23 1210 1610 1610 1610 1610 1/2 - 1 1/4 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 H40TB24 H40TB25 H40TB26 H40TB28 H40TB30 1610 1610 1610 1610 1610 40TB32 40TB35 40TB36 40TB40 40TB42 Steel Double Sprockets HARDENED TEETH Table No. 2 H-57 Part No. Bushing Bore Range Outside Pitch No. of Teeth Type T (Nom.) L H D40TBA15 D40TBA16 D40TBA17 D40TB18 D40TB19 1008 1008 1008 1210 1210 1/2 - 1 1/2 - 1 1/2 - 1 1/2 - 1 1/4 1/2 - 1 1/4 2.65 2.81 2.97 3.14 3.30 2.405 2.563 2.721 2.879 3.038 15 16 17 18 19 3 3 3 2 2 .275 .275 .275 .275 .275 7/8 7/8 7/8 1 1 2 11/16 2 1/2 Wt. Lbs. Less Bush. 0.4 0.5 0.8 0.6 0.8 D40TB20 D40TB21 D40TB23 D40TB25 D40TB30 1610 1610 1610 2012 2012 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 2 1/2 - 2 3.46 3.62 3.94 4.26 5.06 3.196 3.355 3.672 3.989 4.783 20 21 23 25 30 2 2 2 2 2 .275 .275 .275 .275 .275 1 1 1 1 1/4 1 1/4 2 21/32 2 53/64 3 9/64 3 15/32 4 17/64 0.9 1.0 1.3 1.1 2.9 D40TB36 D40TB42 D40TB48 D40TB52 D40TB60 2012 2517 2517 2517 2517 1/2 - 2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 6.02 6.97 7.93 8.57 9.84 5.737 6.691 7.645 8.281 9.554 36 42 48 52 60 2 2 2 2 2 .275 .275 .275 .275 .275 1 1/4 1 3/4 1 3/4 1 3/4 1 3/4 5 1/8 4 1/4 4 1/4 4 1/4 4 1/4 5.3 7.0 9.6 11.4 15.4 D40TB68 D40TB76 D40TB84 2517 2517 2517 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 11.11 12.39 13.66 10.826 12.099 13.372 68 76 84 2 2 2 .275 .275 .275 1 3/4 1 3/4 1 3/4 4 1/4 4 1/4 4 1/4 20.5 25.7 31.6 Diameter Taper Bore Sprockets HARDENED TEETH No. 50 Sprockets for Table No. 1 , 5/8" Pitch ANSI Chain Pitch No. of Teeth Type T Nom. L H 2.415 2.612 2.809 3.006 3.204 12 13 14 15 16 1 1 1 1 1 .343 .343 .343 .343 .343 7/8 7/8 7/8 1 1 1 15/16 1 13/16 1 15/16 2 1/2 2 25/32 Wt. Lbs. Less Bush. 0.3 0.5 0.8 0.6 0.5 3.72 3.92 4.12 4.32 4.52 3.401 3.599 3.797 3.995 4.193 17 18 19 20 21 1 1 1 1 1 .343 .343 .343 .343 .343 1 1 1 1 1 2 25/32 2 25/32 3 3 1/4 3 0.8 1.1 1.3 1.5 1.7 1/2 - 1 5/8 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 4.72 4.92 5.12 5.32 5.52 4.392 4.590 4.788 4.987 5.185 22 23 24 25 26 1 1 1 1 1 .343 .343 .343 .343 .343 1 1 1/4 1 1/4 1 1/4 1 1/4 3 3 7/8 3 7/8 3 7/8 3 7/8 1.9 1.2 1.4 1.5 1.7 2012 2012 2012 2012 2012 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 5.72 5.92 6.32 6.72 7.32 5.384 5.582 5.979 6.376 6.972 27 28 30 32 35 1 1 1 1 1 .343 .343 .343 .343 .343 1 1/4 1 1/4 1 1/4 1 1/4 1 1/4 3 7/8 3 7/8 3 7/8 3 7/8 3 7/8 1.8 1.9 2.3 2.5 3.2 50TB36 50TB40 50TB42 50TB45 50TB48 2012 2012 2012 2012 2012 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 7.52 8.32 8.72 9.31 9.91 7.171 7.966 8.363 8.960 9.556 36 40 42 45 48 1 1 1 1 1 .343 .343 .343 .343 .343 1 1/4 1 1/4 1 1/4 1 1/4 1 1/4 3 7/8 3 7/8 3 7/8 3 7/8 3 7/8 3.6 5.3 5.7 6.4 7.2 50TB54 50TB60 50TB70 50TB72 50TB80 2012 2012 2517 2517 2517 1/2 - 2 1/2 - 2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 11.11 12.30 14.29 14.69 16.28 10.749 11.942 13.931 14.328 15.920 54 60 70 72 80 1 1 1 1 1 .343 .343 .343 .343 .343 1 1/4 1 1/4 1 3/4 1 3/4 1 3/4 3 7/8 3 7/8 4 1/4 4 1/4 4 1/4 9.8 11.0 14.5 15.5 18.8 50TB84 50TB96 50TB112 2517 2517 2517 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 17.08 19.47 22.65 16.715 19.102 22.285 84 96 112 1 1 1 .343 .343 .343 1 3/4 1 3/4 1 3/4 4 1/4 4 1/4 4 1/4 20.7 27.7 37.5 Diameter Part No. Bushing Bore Range Outside H50TB12 H50TB13 H50TB14 H50TB15 H50TB16 1008 1008 1008 1210 1610 1/2 - 1 1/2 - 1 1/2 - 1 1/2 - 1 1/4 1/2 - 1 5/8 2.71 2.91 3.11 3.32 3.52 H50TB17 H50TB18 H50TB19 H50TB20 H50TB21 1610 1610 1610 1610 1610 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 H50TB22 H50TB23 H50TB24 H50TB25 H50TB26 1610 2012 2012 2012 2012 H50TB27 H50TB28 H50TB30 50TB32 50TB35 Steel Double Sprockets HARDENED TEETH Table No. 2 Part No. Bushing Bore Range Outside Pitch No. of Teeth Type T Nom. L H D50TBA14 D50TBA15 D50TBA16 D50TBA17 D50TBA18 D50TBA19 1008 1210 1210 1610 1610 1610 1/2 - 1 1/2 - 1 1/4 1/2 - 1 1/4 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 3.11 3.32 3.52 3.72 3.92 4.12 2.809 3.006 3.204 3.401 3.599 3.797 14 15 16 17 18 19 3 3 3 3 3 3 .332 .332 .332 .332 .332 .332 7/8 1 1 1 1 1 - Wt. Lbs. Less Bush. 0.9 0.7 1.1 0.9 1.1 1.4 D50TB20 D50TB21 D50TB25 D50TB30 D50TB36 2012 2012 2012 2517 2517 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 1/2 1/2 - 2 1/2 4.32 4.52 5.32 6.32 7.52 3.995 4.193 4.987 5.979 7.171 20 21 25 30 36 2 2 2 2 2 .332 .332 .332 .332 .332 1 1/4 1 1/4 1 1/4 1 3/4 1 3/4 3 3/8 3 37/64 4 21/64 5 21/64 4 1/4 0.9 1.3 3.2 6.2 9.4 D50TB42 D50TB48 D50TB52 D50TB60 D50TB68 2517 2517 2517 2517 2517 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 8.72 9.91 10.71 12.30 13.89 8.363 9.556 10.351 11.942 13.533 42 48 52 60 68 2 2 2 2 2 .332 .332 .332 .332 .332 1 3/4 1 3/4 1 3/4 1 3/4 1 3/4 4 1/4 4 1/4 4 3/8 4 3/8 4 3/8 13.4 18.6 22.2 30.3 39.4 D50TB76 D50TB84 D50TB95 2517 2517 2517 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 15.49 17.08 19.27 15.124 16.715 18.903 76 84 95 2 2 2 .332 .332 .332 1 3/4 1 3/4 1 3/4 4 3/8 4 3/8 4 3/8 41.2 45.3 58.8 Diameter H-58 Taper Bore Sprockets HARDENED TEETH No. 60 Sprockets for Table No. 1 , 3/4" Pitch ANSI Chain Diameter Part No. Bushing Bore Range Outside Pitch No. of Teeth Type T (Nom.) L H Wt. Lbs. Less Bush H60TB11 H60TB12 H60TB13 H60TB14 H60TB15 1008 1008 1210 1210 1610 1/2 - 1 1/2 - 1 1/2 - 1 1/4 1/2 - 1 1/4 1/2 - 1 5/8 3.00 3.25 3.49 3.74 3.98 2.662 2.898 3.134 3.370 3.607 11 12 13 14 15 1 1 1 1 1 .459 .459 .459 .459 .459 7/8 7/8 1 1 1 1 13/16 1 15/16 2 21/32 2 15/16 3 1/8 0.8 1.0 1.1 1.4 1.5 H60TB16 H60TB17 H60TB18 H60TB19 H60TB20 1610 1610 1610 1610 2012 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 2 4.22 4.46 4.70 4.94 5.19 3.844 4.082 4.319 4.557 4.794 16 17 18 19 20 1 1 1 1 1 .459 .459 .459 .459 .459 1 1 1 1 1 1/4 3 3 1/4 3 3 3 7/8 1.8 2.2 3.0 3.2 2.6 H60TB21 H60TB22 H60TB23 H60TB24 H60TB25 2012 2012 2012 2012 2012 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 5.43 5.67 5.91 6.15 6.39 5.032 5.270 5.508 5.746 5.984 21 22 23 24 25 1 1 1 1 1 .459 .459 .459 .459 .459 1 1/4 1 1/4 1 1/4 1 1/4 1 1/4 3 7/8 3 7/8 3 7/8 3 7/8 3 7/8 2.8 3.4 3.7 4.0 4.2 H60TB26 H60TB27 H60TB28 H60TB30 2012 2012 2012 2012 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 6.63 6.87 7.11 7.59 6.222 6.460 6.699 7.175 26 27 28 30 1 1 1 1 .459 .459 .459 .459 1 1/4 1 1/4 1 1/4 1 1/4 3 7/8 3 7/8 3 7/8 3 7/8 4.5 4.6 5.5 6.1 60TB32 60TB35 60TB36 60TB40 60TB42 2012 2012 2012 2012 2012 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 8.06 8.78 9.02 9.98 10.46 7.652 8.367 8.605 9.559 10.036 32 35 36 40 42 1 1 1 1 1 .459 .459 .459 .459 .459 1 1/4 1 1/4 1 1/4 1 1/4 1 1/4 3 7/8 3 7/8 3 7/8 3 7/8 3 7/8 6.8 8.3 8.9 10.7 11.3 60TB45 60TB48 60TB54 60TB60 60TB70 2012 2012 2517 2517 2517 1/2 - 2 1/2 - 2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 11.18 11.89 13.33 14.76 17.15 10.752 11.467 12.899 14.330 16.717 45 48 54 60 70 1 1 1 1 1 .459 .459 .459 .459 .459 1 1/4 1 1/4 1 3/4 1 3/4 1 3/4 3 7/8 3 7/8 4 1/4 4 1/4 4 1/4 12.8 14.2 19.2 22.9 29.0 60TB72 60TB80 60TB84 2517 2517 2517 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 17.63 19.54 20.49 17.194 19.104 20.058 72 80 84 1 1 1 .459 .459 .459 1 3/4 1 3/4 1 3/4 4 1/4 4 1/4 4 1/4 30.7 38.5 42.5 Steel Double Sprockets HARDENED TEETH Table No. 2 H-59 Diameter Part No. Bushing Bore Range Outside Pitch No. of Teeth Type T (Nom.) L H Wt. Lbs. Less Bush D60TB13 D60TB14 D60TB15 D60TB16 D60TB17 1215 1215 1615 1615 1615 1/2 - 1 1/4 1/2 - 1 1/4 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 3.49 3.74 3.98 4.22 4.46 3.134 3.370 3.607 3.844 4.082 13 14 15 16 17 2 2 2 2 2 .444 .444 .444 .444 .444 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 2 19/64 2 35/64 3 25/32 3 1/32 3 17/64 1.2 1.6 1.3 1.8 2.3 D60TBA18 D60TBA19 D60TB20 D60TB21 D60TB25 2012 2012 2517 2517 2517 1/2 - 2 1/2 - 2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 4.70 4.94 5.19 5.43 6.39 4.319 4.557 4.794 5.032 5.984 18 19 20 21 25 3 3 2 2 2 .444 .444 .444 .444 .444 1 1/4 1 1/4 1 3/4 1 3/4 1 3/4 3 63/64 4 15/64 5 3/16 1.9 2.3 1.6 2.4 6.1 D60TB30 D60TB36 D60TB42 D60TB45 D60TB52 2517 2517 2517 2517 2517 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 7.59 9.02 10.46 11.18 12.85 7.175 8.605 10.036 10.752 12.422 30 36 42 45 52 2 2 2 2 2 .444 .444 .444 .444 .444 1 3/4 1 3/4 1 3/4 1 3/4 1 3/4 6 25/64 4 1/4 4 1/4 4 1/4 4 1/4 11.5 17.5 25.5 29.5 41.0 D60TB60 D60TB68 D60TB76 D60TB95 2517 2517 3020 3020 1/2 - 2 1/2 1/2 - 2 1/2 15/16 - 3 15/16 - 3 14.76 16.67 18.58 23.12 14.330 16.240 18.149 22.684 60 68 76 95 2 2 2 2 .444 .444 .444 .444 1 3/4 1 3/4 2 2 4 1/4 4 1/2 5 1/4 5 1/4 32.5 36.5 42.5 48.5 Taper Bore Sprockets HARDENED TEETH No. 80 Sprockets for Table No. 1 , 1" Pitch ANSI Chain Diameter Part No. Bushing Bore Range Outside Pitch No. of Teeth Type T (Nom.) L H Wt.lbs. Less Bush. H80TB10 H80TB11 H80TB12 H80TB13 H80TB14 1215 1215 1615 1615 1615 1/2 - 1 3/8 1/2 - 1 3/8 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 1 5/8 3.68 4.01 4.33 4.66 4.98 3.236 3.549 3.864 4.179 4.494 10 11 12 13 14 1 1 1 1 1 .575 .575 .575 .575 .575 1 1/2 1 1/2 1 1/2 1 1/2 1 1/2 2 1/2 2 15/32 3 3 3 7/32 1.4 1.5 1.2 2.3 3.1 H80TB15 H80TB16 H80TB17 H80TB18 H80TB19 1615 2012 2012 2012 2012 1/2 - 1 5/8 1/2 - 2 1/2 - 2 1/2 - 2 1/2 - 2 5.30 5.63 5.95 6.27 6.59 4.810 5.126 5.442 5.759 6.076 15 16 17 18 19 1 1 1 1 1 .575 .575 .575 .575 .575 1 1/2 1 1/4 1 1/4 1 1/4 1 1/4 3 7/32 3 7/8 3 7/8 3 7/8 3 7/8 3.5 4.4 5.3 5.7 6.1 H80TB20 H80TB21 H80TB22 H80TB23 H80TB24 2517 2517 2517 2517 2517 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 6.91 7.23 7.56 7.88 8.20 6.392 6.710 7.027 7.344 7.661 20 21 22 23 24 1 1 1 1 1 .575 .575 .575 .575 .575 1 3/4 1 3/4 1 3/4 1 3/4 1 3/4 4 1/4 4 1/4 4 1/4 4 1/4 4 1/4 4.8 5.2 5.8 6.3 7.0 H80TB25 H80TB26 H80TB27 H80TB28 H80TB30 2517 2517 2517 2517 2517 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 8.52 8.84 9.16 9.48 10.11 7.979 8.296 8.614 8.931 9.567 25 26 27 28 30 1 1 1 1 1 .575 .575 .575 .575 .575 1 3/4 1 3/4 1 3/4 1 3/4 1 3/4 4 1/4 4 1/4 4 1/4 4 1/4 4 1/4 7.6 9.9 10.0 10.0 12.6 80TB32 80TB35 80TB36 80TB40 80TB45 2517 2517 2517 2517 2517 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 10.75 11.71 12.03 13.31 14.90 10.202 11.156 11.474 12.745 14.336 32 35 36 40 45 1 1 1 1 1 .575 .575 .575 .575 .575 1 3/4 1 3/4 1 3/4 1 3/4 1 3/4 4 1/4 4 1/4 4 1/4 4 1/4 4 1/4 14.1 14.5 17.6 21.1 28.0 80TB48 80TB54 80TB60 80TB70 80TB80 2517 2517 2517 3020 3020 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 15/16 - 3 15/16 - 3 15.86 17.77 19.68 22.87 26.05 15.290 17.198 19.107 22.289 25.471 48 54 60 70 80 1 1 1 1 1 .575 .575 .575 .575 .575 1 3/4 1 3/4 1 3/4 2 2 4 1/4 4 1/4 4 1/4 5 1/4 5 1/4 31.4 38.8 47.2 63.5 83.5 Steel Double Sprockets Table No. 2 HARDENED TEETH H Diameter Part No. Bushing Bore Range Outside Pitch No. of Teeth Type T (Nom.) L H Wt.lbs. Less Bush. D80TBA13 D80TBA14 D80TBA15 D80TBA16 D80TBA17 D80TBA18 1615 2012 2012 2517 2517 2517 1/2 - 1 5/8 1/2 - 2 1/2 - 2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 4.66 4.98 5.30 5.63 5.95 6.27 4.179 4.494 4.810 5.126 5.442 5.759 13 14 15 16 17 18 3 3 3 3 3 3 .557 .557 .557 .557 .557 .557 1 1/2 1 1/4 1 1/4 1 3/4 1 3/4 1 3/4 — — — — — — 2.7 2.5 3.5 2.5 3.6 4.9 D80TB19 D80TB20 D80TB21 D80TB25 D80TB30 3020 3020 3020 3020 3020 15/16 - 3 15/16 - 3 15/16 - 3 15/16 - 3 15/16 - 3 6.59 6.91 7.23 8.52 10.11 6.076 6.392 6.710 7.979 9.567 19 20 21 25 30 2 2 2 2 2 .557 .557 .557 .557 .557 2 2 2 2 2 5 5 5/16 5 41/64 6 59/64 5 1/4 3.2 4.5 6.5 14.5 25.1 D80TB36 D80TB42 D80TB45 D80TB52 D80TB60 3020 3020 3020 3020 3020 15/16 - 3 15/16 - 3 15/16 - 3 15/16 - 3 15/16 - 3 12.03 13.94 14.90 17.13 19.68 11.474 13.381 14.336 16.562 19.107 36 42 45 52 60 2 2 1 2 2 .557 .557 .557 .557 .557 2 2 2 2 2 5 1/4 5 1/4 5 1/4 5 1/4 5 1/4 39.4 36.4 41.4 56.2 66.3 D80TB68 D80TB76 3020 3020 15/16 - 3 15/16 - 3 22.23 24.78 21.653 24.198 68 76 2 2 .557 .557 2 2 5 1/4 5 1/4 72.0 89.1 H-60 Taper Bore Sprockets HARDENED TEETH Table No. 1 H-61 Sprockets for No. 100 , 1 1/4" Pitch ANSI Chain Diameter Part No. Bushing Bore Range Outside Pitch No. of Teeth Type T (Nom.) L H Wt. lbs. less Bush. H100TB11 H100TB12 H100TB13 H100TB14 H100TB15 1615 1615 2012 2012 2517 1/2 - 1 5/8 1/2 - 1 5/8 1/2 - 2 1/2 - 2 1/2 - 2 1/2 5.01 5.42 5.82 6.23 6.63 4.437 4.830 5.223 5.617 6.012 11 12 13 14 15 1 1 1 1 1 .692 .692 .692 .692 .692 1 1/2 1 1/2 1 1/4 1 1/4 1 3/4 3 3 7/32 3 7/8 3 7/8 4 1/4 3.0 5.1 5.8 8.1 7.2 H100TB16 H100TB17 H100TB18 H100TB19 H100TB20 2517 2517 2517 2517 2517 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 7.03 7.44 7.84 8.24 8.64 6.407 6.803 7.198 7.594 7.991 16 17 18 19 20 1 1 1 1 1 .692 .692 .692 .692 .692 1 3/4 1 3/4 1 3/4 1 3/4 1 3/4 4 1/4 4 1/4 4 1/4 4 1/4 4 1/4 8.0 8.8 9.7 11.7 12.7 H100TB21 H100TB22 H100TB24 H100TB26 H100TB28 H100TB30 2517 2517 2517 2517 3020 3020 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 1/2 - 2 1/2 15/16 - 3 15/16 - 3 9.04 9.44 10.24 11.04 11.84 12.64 8.387 8.783 9.577 10.370 11.164 11.958 21 22 24 26 28 30 1 1 1 1 1 1 .692 .692 .692 .692 .692 .692 1 3/4 1 3/4 1 3/4 1 3/4 2 2 4 1/4 4 1/4 4 1/4 4 1/4 5 1/4 5 1/4 13.8 14.8 17.3 21.0 21.1 23.5 100TB32 100TB35 100TB36 100TB40 3020 3020 3020 3020 15/16 - 3 15/16 - 3 15/16 - 3 15/16 - 3 13.44 14.64 15.04 16.63 12.753 13.945 14.342 15.932 32 35 36 40 1 1 1 1 .692 .692 .692 .692 2 2 2 2 5 1/4 5 1/4 5 1/4 5 1/4 26.5 28.5 34.0 41.3 100TB45 100TB48 100TB54 100TB60 3020 3020 3020 3020 15/16 - 3 15/16 - 3 15/16 - 3 15/16 - 3 18.63 19.82 22.21 24.60 17.919 19.112 21.498 23.884 45 48 54 60 1 1 1 1 .692 .692 .692 .692 2 2 2 2 5 1/4 5 1/4 5 1/4 5 1/4 51.5 57.5 71.5 87.5 Taper Bore Sprockets Table No. 1 HARDENED TEETH Part No. Bushing Bore Range No. 120 , 1 1/2" Pitch ANSI Chain Diameter Outside Pitch No. of Teeth Type T (Nom.) L H Wt.lbs. less Bush. H120TB12 2012 1/2 - 2 6.50 5.796 12 1 .924 1 1/4 3 9/16 5.5 H120TB13 2517 1/2 - 2 1/2 6.99 6.268 13 1 .924 1 3/4 4 1/4 8.0 H120TB14 2517 1/2 - 2 1/2 7.47 6.741 14 1 .924 1 3/4 4 1/4 9.3 H120TB15 2517 1/2 - 2 1/2 7.96 7.215 15 1 .924 1 3/4 4 1/4 10.5 H120TB16 3020 15/16 - 3 8.44 7.689 16 1 .924 2 5 1/4 9.1 H120TB17 3020 15/16 - 3 8.92 8.163 17 1 .924 2 5 1/4 15.0 H120TB18 3020 15/16 - 3 9.41 8.638 18 1 .924 2 5 1/4 17.0 H120TB19 3020 15/16 - 3 9.89 9.113 19 1 .924 2 5 1/4 19.1 H120TB20 3020 15/16 - 3 10.37 9.589 20 1 .924 2 5 1/4 15.5 H120TB21 3020 15/16 - 3 10.85 10.064 21 1 .924 2 5 1/4 17.5 H120TB24 3020 15/16 - 3 12.29 11.492 24 1 .924 2 5 1/4 23.5 H120TB26 3020 15/16 - 3 13.25 12.444 26 1 .924 2 5 1/4 32.5 H120TB30 3020 15/16 - 3 15.17 14.350 30 1 .924 2 5 1/4 33.5 120TB35 3020 15/16 - 3 17.57 16.734 35 1 .924 2 5 1/4 52.0 120TB36 3020 15/16 - 3 18.05 17.211 36 1 .924 2 5 1/4 54.0 120TB45 3030 15/16 - 3 22.35 21.503 45 1 .924 3 5 7/8 82.0 120TB60 3535 15/16 - 3 29.52 28.661 60 1 .924 3 1/2 6 1/2 140.0 120TB70 3535 15/16 - 3 34.30 33.434 70 1 .924 3 1/2 6 1/2 175.0 120TB80 3535 15/16 - 3 39.08 38.207 80 1 .924 3 1/2 6 1/2 220.0 Table No. 2 Part No. HARDENED TEETH Sprockets for Sprockets for No. 140 , 1 3/4" Pitch ANSI Chain Diameter Bushing Bore Range H140TB12 2517 1/2 - 2 1/2 7.58 6.761 12 H140TB13 3020 15/16 - 3 8.15 7.313 13 Outside Pitch No. of Teeth T (Nom.) L 1 .924 1 3/4 4 1/4 10.5 1 .924 2 5 1/4 12.5 Type H Wt.lbs. less Bush. H140TB14 3020 15/16 - 3 8.72 7.864 14 1 .924 2 5 1/4 13.5 H140TB15 3020 15/16 - 3 9.28 8.417 15 1 .924 2 5 1/4 15.5 H140TB16 3020 15/16 - 3 9.85 8.970 16 1 .924 2 5 1/4 17.5 H140TB17 3020 15/16 - 3 10.41 9.524 17 1 .924 2 5 1/4 19.5 H140TB18 3020 15/16 - 3 10.97 10.078 18 1 .924 2 5 1/4 22.5 H140TB19 3020 15/16 - 3 11.54 10.632 19 1 .924 2 5 1/4 25.5 H140TB21 3020 15/16 - 3 12.66 11.742 21 1 .924 2 5 1/4 29.5 H140TB26 3020 15/16 - 3 15.46 14.518 26 1 .924 2 5 1/4 44.5 140TB35 3535 15/16 - 3 20.49 19.523 35 1 .924 3 1/2 6 1/2 78.0 140TB36 3535 15/16 - 3 21.05 20.079 36 1 .924 3 1/2 6 1/2 83.0 140TB45 4040 1 7/16 - 4 26.08 25.087 45 1 .924 4 7 3/4 118.0 140TB60 4040 1 7/16 - 4 34.44 33.438 60 1 .924 4 7 3/4 188.0 140TB70 4040 1 7/16 - 4 40.02 39.006 70 1 .924 4 7 3/4 241.0 H-62 Taper Bore Sprockets HARDENED TEETH Part No. H-63 Diameter Bushing Bore Range Outside Pitch No. of Teeth Type T (Nom.) L H Wt. lbs. Less Bush. H160TB11 2517 1/2 - 2 1/2 8.01 7.099 11 1 1.156 1 3/4 4 1/4 11.5 H160TB12 3020 15/16 - 3 8.66 7.727 12 1 1.156 2 5 1/4 13.5 H160TB13 3020 15/16 - 3 9.31 8.357 13 1 1.156 2 5 1/4 15.5 H160TB14 3020 15/16 - 3 9.96 8.988 14 1 1.156 2 5 1/4 17.5 H160TB15 3535 15/16 - 3 10.61 9.619 15 1 1.156 3 1/2 6 1/2 16.0 H160TB16 3535 15/16 - 3 11.25 10.252 16 1 1.156 3 1/2 6 1/2 19.0 H160TB17 3535 15/16 - 3 11.90 10.884 17 1 1.156 3 1/2 6 1/2 22.0 H160TB18 3535 15/16 - 3 12.54 11.518 18 1 1.156 3 1/2 6 1/2 26.0 H160TB19 3535 15/16 - 3 13.19 12.151 19 1 1.156 3 1/2 6 1/2 35.0 H160TB20 3535 15/16 - 3 13.83 12.785 20 1 1.156 3 1/2 6 1/2 44.0 H160TB21 3535 15/16 - 3 14.47 13.419 21 1 1.156 3 1/2 6 1/2 54.0 H160TB24 3535 15/16 - 3 16.39 15.323 24 1 1.156 3 1/2 6 1/2 59.0 H160TB26 3535 15/16 - 3 17.67 16.592 26 1 1.156 3 1/2 6 1/2 86.0 160TB35 4040 1 7/16 - 4 23.42 22.312 35 1 1.156 4 7 3/4 118.0 160TB36 4040 1 7/16 - 4 24.06 22.947 36 1 1.156 4 7 3/4 130.0 160TB45 4040 1 7/16 - 4 29.80 28.671 45 1 1.156 4 7 3/4 186.0 160TB60 4040 1 15/16 - 4 1/2 39.36 38.215 60 1 1.156 4 1/2 8 3/4 292.0 Stock Double Single Sprockets HARDENED TEETH Steel Double Single Sprockets with Browning Split Taper® Bushings Table No. 1 Part No. Bushing Bore Range DIAMETERS Outside Pitch No. Type Teeth T M OL L C H G E Wt. Less Bushing .284” .284 .284 .284 1 13/32” 1 13/32 1 13/32 1 13/32 2 1/32” 2 1/32 2 9/32 2 9/32 1 1/4” 1 1/4 1 15/16 1 15/16 19/32” 19/32 3/32 3/32 2 1/2” 2 1/2 3 3 7/16” 7/16 5/8 5/8 3/16” 3/16 1/4 1/4 1.5 2.0 2.3 2.5 .343 .343 .343 .343 .343 1 21/32 1 21/32 1 21/32 1 21/32 1 21/32 2 9/32 2 17/32 2 17/32 2 17/32 2 17/32 1 1/4 1 15/16 1 15/16 1 15/16 1 15/16 27/32 11/32 11/32 11/32 11/32 2 1/2 3 3 3 3 7/16 5/8 5/8 5/8 5/8 3/16 1/4 1/4 1/4 1/4 2.3 2.8 3.8 4.6 5.0 .459 .459 .459 .459 .459 .459 1 61/64 1 61/64 1 61/64 1 61/64 1 61/64 1 61/64 2 53/64 2 53/64 2 63/64 2 63/64 2 63/64 2 63/64 1 15/16 1 15/16 2 1/2 2 1/2 2 1/2 2 1/2 41/64 41/64 13/64 13/64 13/64 13/64 3 3 4 1/8 4 1/8 4 1/8 4 1/8 5/8 5/8 3/4 3/4 3/4 3/4 1/4 1/4 9/32 9/32 9/32 9/32 3.9 5.3 5.4 6.2 6.9 7.6 .575 .575 .575 .575 .575 2 13/64 2 13/64 2 13/64 2 13/64 2 13/64 3 15/64 3 15/64 3 15/64 3 23/64 3 23/64 2 1/2 2 1/2 2 1/2 2 7/8 2 7/8 29/64 29/64 29/64 13/64 13/64 4 1/8 4 1/8 4 1/8 5 3/8 5 3/8 3/4 3/4 3/4 7/8 7/8 9/32 9/32 9/32 9/32 9/32 7.2 10.5 12.2 10.3 13.2 2 11/16 2 11/16 2 11/16 3 27/32 3 27/32 3 27/32 2 7/8 2 7/8 2 7/8 11/16 11/16 11/16 5 3/8 5 3/8 5 3/8 7/8 7/8 7/8 9/32 9/32 9/32 12.5 18.8 23.1 DIMENSIONS For No. 40, 1/2” Pitch Standard Single Strand Roller Chain DS40H19 DS40H21 DS40P23 DS40P24 H H P1 P1 3/8 - 1 1/2” 3/8 - 1 1/2 1/2 - 1 3/4 1/2 - 1 3/4 3.28” 3.62 3.94 4.10 3.038” 3.355 3.672 3.831 19 21 23 24 DS-1 DS-1 DS-2 DS-2 For No. 50, 5/8” Pitch Standard Single Strand Roller Chain DS50H17 DS50P19 DS50P21 DS50P23 DS50P24 H P1 P1 P1 P1 3/8 - 1 1/2 1/2 - 1 3/4 1/2 - 1 3/4 1/2 - 1 3/4 1/2 - 1 3/4 3.72 4.12 4.52 4.92 5.12 3.401 3.797 4.194 4.590 4.788 17 19 21 23 24 DS-1 DS-2 DS-2 DS-2 DS-2 For No. 60, 3/4” Pitch Standard Single Strand Roller Chain DS60P17 DS60P19 DS60Q21 DS60Q22 DS60Q23 DS60Q24 P1 P1 Q1 Q1 Q1 Q1 1/2 - 1 3/4 1/2 - 1 3/4 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 4.46 4.95 5.43 5.67 5.91 6.15 4.082 4.557 5.032 5.270 5.508 5.746 17 19 21 22 23 24 DS-2 DS-2 DS-2 DS-2 DS-2 DS-2 For No. 80, 1” Pitch Standard Single Strand Roller Chain DS80Q17 DS80Q19 DS80Q20 DS80R21 DS80R23 Q1 Q1 Q1 R1 R1 3/4 - 2 11/16 3/4 - 2 11/16 3/4 - 2 11/16 1 1/8 - 3 3/4 1 1/8 - 3 3/4 5.95 6.59 6.91 7.24 7.88 5.442 6.076 6.392 6.710 7.344 17 19 20 21 23 DS-2 DS-2 DS-2 DS-2 DS-2 For No. 100, 1 1/4” Pitch Standard Single Strand Roller Chain DS100R17 DS100R19 DS100R21 R1 R1 R1 1 1/8 - 3 3/4 1 1/8 - 3 3/4 1 1/8 - 3 3/4 7.44 8.24 9.04 6.803 7.595 8.387 17 19 21 DS-2 DS-2 DS-2 .692 .692 .692 Browning Stock Double Single Sprockets with Split Taper Bushings are for use with two single strand chains, normally one drive chain and one driven chain as on roll case drives or live roller conveyor drives. They are made of steel, have HARDENED TEETH and are ready to use right off the shelf. No reworking is necessary since they use Browning Split Taper Bushings. Standard Keyseats Table No. 2 Bore Range Keyseat 3/8" — 7/16" 1/2 — 9/16 5/8 — 7/8 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 2 13/16 — 3 1/4 3 3/8 — 3 3/4 None 1/8" x 1/16" 3/16 x 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 3/4 x 3/8 7/8 x 7/16 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-64 Stock Double Single Sprockets HARDENED TEETH Stock Steel Type "A" Double Single Sprockets Table No. 1 Part No. DIAMETERS O.D. P.D. D Type No. Teeth Bore “B” DIMENSIONS Stock Max. M T Wt. Lbs. For No. 40, 1/2” Pitch Standard Single Strand Roller Chain DS40A17 2.96” 2.721” 2 9/64” DS-A 17 1/2” 1 7/16” 1 13/32” .284” 2.8 DS40A19 3.28 3.038 2 15/32 DS-A 19 5/8 1 3/4 1 13/32 .284 3.4 DS40A21 3.62 3.355 2 25/32 DS-A 21 5/8 1 7/8 1 13/32 .284 4.1 For No. 50, 5/8” Pitch Standard Single Strand Roller Chain DS50A17 3.72 3.401 2 11/16 DS-A 17 5/8 1 7/8 1 21/32 .343 4.1 DS50A19 4.12 3.797 3 5/32 DS-A 19 5/8 2 1/8 1 21/32 .343 5.1 DS50A21 4.52 4.194 3 1/2 DS-A 21 5/8 2 3/8 1 21/32 .343 6.3 6.8 For No. 60, 3/4” Pitch Standard Single Strand Roller Chain DS60A17 4.46 4.082 3 1/4 DS-A 17 3/4 2 1/4 1 61/64 .459 DS60A19 4.95 4.557 3 23/32 DS-A 19 3/4 2 1/2 1 61/64 .459 8.5 DS60A21 5.43 5.032 4 13/64 DS-A 21 3/4 2 3/4 1 61/64 .459 10.5 For No. 80, 1” Pitch Standard Single Strand Roller Chain DS80A17 5.95 5.442 4 21/64 DS-A 17 1 2 13/16 2 13/64 .575 13.8 DS80A19 6.59 6.076 4 31/32 DS-A 19 1 3 1/4 2 13/64 .575 17.4 DS80A21 7.24 6.710 5 39/64 DS-A 21 1 3 3/4 2 13/64 .575 21.4 Browning Stock Type "A" Double Single Sprockets are for use with two single strand chains, normally one drive chain and one driven chain as on roll case drives or live roller conveyor drives. They are made of steel and have HARDENED TEETH. They can be rebored to the maximum shown in the table which is with standard keyway and setscrew over keyway. Slightly larger bores are possible with no keyway or with setscrew at angle to keyway. H-65 Sprockets for Extended Pitch Chain Browning Stock Sprockets for Extended Pitch Chain have larger pitch diameters than standard roller chain sprockets as extended pitch chain will not operate satisfactorily on standard roller chain sprockets with less than 24 teeth. They will normally operate satisfactorily on standard roller chain sprockets with 24 or more teeth. Sprockets for Extended Pitch Chain with Large Rollers are available on special order. Table No. 1 Stock Sprockets with Browning Split Taper® Bushings for Extended Pitch Chain with Standard Rollers For No. 2040,1” Extended Pitch Roller Chain Part No. Bushing Bore Range Diameter Outside Pitch 2040H17 H 3/8 - 1 1/2 2.96 2.768 2040H21 H 3/8 - 1 1/2 3.62 3.392 For No. 2050,1 1/4” Extended Pitch Roller Chain 2050H17 H 3/8 - 1 1/2 3.72 3.460 2050P21 P1 1/2 - 1 3/4 4.52 4.241 2050P23 P1 1/2 - 1 3/4 4.92 4.633 For No. 2060,1 1/2” Extended Pitch Roller Chain 2060P17 P1 1/2 - 1 3/4 4.46 4.152 2060P19 P1 1/2 - 1 3/4 4.95 4.620 2060P23 P1 1/2 - 1 3/4 5.90 5.560 For No. 2080,2” Extended Pitch Roller Chain 2080P17 P1 1/2 - 1 3/4 5.94 5.536 2080Q19 Q1 3/4 - 2 11/16 6.59 6.160 2080Q21 Q1 3/4 - 2 11/16 7.23 6.785 2080Q23 Q1 3/4 - 2 11/16 7.87 7.413 No. of Teeth.* Type T (Nom.) O.L. L P C H G X E 17 17 3 3 .275 .275 1 1/2 1 1/2 1 1/4 1 1/4 1 1/32 1 1/32 1/16 1/16 2 1/2 2 1/2 7/16 7/16 7/8 7/8 3/16 3/16 Wt. lbs. less Bush. .6 .9 17 21 23 3 4 4 .343 .343 .343 1 1/2 2 3/16 2 3/16 1 1/4 31/32 1 15/16 1 19/32 1 15/16 1 19/32 1/16 0 0 2 1/2 3 3 7/16 5/8 5/8 7/8 1 5/16 1 5/16 3/16 1/4 1/4 1.0 2.0 2.4 17 19 23 4 4 4 .459 .459 .459 2 3/16 2 3/16 2 3/16 1 15/16 1 15/32 1 15/16 1 15/32 1 15/16 1 15/32 0 0 0 3 3 3 5/8 5/8 5/8 1 5/16 1 5/16 1 5/16 1/4 1/4 1/4 2.2 2.6 3.5 17 19 21 23 4 4 4 4 .575 .575 .575 .575 2 3/16 2 25/32 2 25/32 2 25/32 1 15/16 2 1/2 2 1/2 2 1/2 0 0 0 0 3 4 1/8 4 1/8 4 1/8 5/8 3/4 3/4 3/4 1 5/16 1 3/4 1 3/4 1 3/4 1/4 9/32 9/32 9/32 3.9 6.4 7.4 8.5 1 3/8 1 3/8 1 3/8 1 3/8 Table No. 2 Stock Sprockets with Taper Bore Bushings for Extended Pitch Chain with Standard Rollers For No. 2040, 1" Extended pitch Roller Chain Part No. Bushing Bore Range Diameter Outside Pitch 2040TB17 1008 1/2 - 1 2.97 2.768 2040TB19 1210 1/2 - 1 1/4 3.30 3.080 2040TB21 1610 1/2 - 1 5/8 3.62 3.392 2040TB23 1610 1/2 - 1 5/8 3.94 3.706 2040TB25 1610 1/2 - 1 5/8 4.26 4.021 2040TB35 1610 1/2 - 1 5/8 5.86 5.600 For No. 2050, 1 1/4” Extended Pitch Roller Chain 2050TB17 1210 1/2 - 1 1/4 3.72 3.460 2050TB19 1610 1/2 - 1 5/8 4.12 3.850 2050TB21 1610 1/2 - 1 5/8 4.52 4.241 2050TB23 2012 1/2 - 2 4.92 4.633 2050TB25 2012 1/2 - 2 5.32 5.026 2050TB35 2012 1/2 - 2 7.32 6.927 For No. 2060, 1 1/2” Extended Pitch Roller Chain 2060TB17 1610 1/2 - 1 5/8 4.46 4.152 2060TB19 1610 1/2 - 1 5/8 4.94 4.620 2060TB21 2012 1/2 - 2 5.43 5.089 2060TB23 2012 1/2 - 2 5.91 5.560 2060TB25 2012 1/2 - 2 6.39 6.032 2060TB35 2012 1/2 - 2 8.78 8.367 For No. 2080, 2” Extended Pitch Roller Chain 2080TB17 2012 1/2 - 2 5.95 5.536 2080TB19 2517 1/2 - 2 1/2 6.59 6.160 2080TB21 2517 1/2 - 2 1/2 7.23 6.785 2080TB23 2517 1/2 - 2 1/2 7.88 7.413 2080TB25 2517 1/2 - 2 1/2 8.52 8.042 2080TB35 2517 1/2 - 2 1/2 11.71 11.156 *NOTE — Chain engages every other tooth in sprocket. No. of Teeth.* Type T (Nom.) O.L. L Wt. lbs. less Bush 17 19 21 23 25 35 1 1 1 1 1 1 .275 .275 .275 .275 .275 .275 7/8 1 1 1 1 1 2 2 15/32 2 25/32 3 3 1/4 3 1.0 1.4 1.7 1.8 2.1 3.4 17 19 21 23 25 35 1 1 1 1 1 1 .343 .343 .343 .343 .343 .343 1 1 1 1 1/4 1 1/4 1 1/4 2 25/32 2 15/16 3 3 7/8 3 7/8 3 7/8 1.3 2.1 2.2 3.3 3.8 5.6 17 19 21 23 25 35 1 1 1 1 1 1 .459 .459 .459 .459 .459 .459 1 1 1 1/4 1 1/4 1 1/4 1 1/4 3 3 3 7/8 3 7/8 3 7/8 3 7/8 2.5 3.0 4.1 4.7 5.3 8.6 17 19 21 23 25 35 1 1 1 1 1 1 .575 .575 .575 .575 .575 .575 1 1/4 1 3/4 1 3/4 1 3/4 1 3/4 1 3/4 3 7/8 4 1/4 4 1/4 4 1/4 4 1/4 4 1/4 4.8 9.0 9.7 10.8 11.7 19.3 Standard Keyseats Table No. 3 Bore Range Keyseat 3/8" — 7/16" 1/2 — 9/16 5/8 — 7/8 15/16 — 1 1/4 1 5/16 — 1 3/8 1 7/16 — 1 3/4 1 13/16 — 2 1/4 2 5/16 — 2 3/4 None 1/8" x 1/16" 3/16 x 3/32 1/4 X 1/8 5/16 X 5/32 3/8 X 3/16 1/2 x 1/4 5/8 x 5/16 1 3/8" Bore Bushings also available with 3/8" x 3/16" Keyseat. H-66 Notes: H-67
Similar documents
Sprocket Catalog
abrasion, and withstand heavy shock loads. Alloy and stainless steel
sprockets are also available for extra corrosion resistance and food-grade
applications. Precision manufacturing at our ISO-cert...
