8031 winter gardens blvd suite 41 el cajon, ca

BMW LED
8031 WINTER GARDENS BLVD
SUITE 41
EL CAJON, CA 92021
(619) 792-2872
www.bmwled.com
www.bmwled.net
BMWLED Angel Eye Marker Installation
E90/E91/E92/E93
Time Estimate (25 Minutes per side)
Tools Required:
 1 Jack
 17mm Socket + Wrench
o This will remove tire
o Possibly a Rubber Mallet
 10mm Socket
 8mm Socket
 Slotted Screw Driver
 Torx Wrench (T-15)
Process:
1. Jack up BMW, remove wheel
2. Remove entire wheel well
3. Remove back plastic housing of OEM Angel Eye housing
4. Unscrew OEM bulb
5. Connect in New BMWLED Angel Eye.
a. Blue Wire=Postive
b. White Wire=Negative
6. Test and screw into place
7. Put back plastic housing back on
8. Reinstall wheel well
*For E90 2006* you will need to modify housing so it can fit properly into the car’s
housing. This is shown below.
Original, the black piece will not fit inside housing. This must be removed (very
easy)
Take flat head and remove both plastic sides.
Slide out electronics from black housing
Slide electronics into light fixture. This is safe and okay.
Done, ready to install. Follow instructions below.
Process with Pictures:
Process 1:
Jack up BMW and remove the wheel.
Once the car is placed on a jack, use your 17mm socket to remove all 5 nuts and
remove wheel. If wheel is hard to slide off, try hitting the tire softly with a rubber
mallet in a circular motion to loosen. By doing so the wheel should come off easily
from there. Place wheel in a safe location and continue to Process 2.
Process 2:
Remove entire wheel well
By removing the wheel well, you can access the light housing much easier. The
wheel well is held together with 9 screws and 1 nut. Additionally, there are 4 screws
to be removed underneath the front bumper. Once all screws/nuts are removed,
move wheel well around to free up and remove it. Place wheel well off to the side
and continue onto Process 3.
(This vehicle had some screws missing from previous installations)
(Underneath bumper, remove screws and nuts such as one displayed that are
holding wheel well)
Process 3:
Remove back plastic housing of OEM Angel Eye housing
To remove this cover, place your body into wheel well and locate the two clips on
the housing (top and bottom). Grab you slotted screwdriver and unclip. For this
process I tried to pry but was afraid I was going to break the plastic. Instead I placed
the flat head in-between the housing and the clip and made a twisting motion while
gently pulling on the housing.
Came off easily and safely.
Remove housing and continue onto Process 4.
Process 4:
Unscrew OEM bulb
Picture below shows old bulb. This particular one is not OEM, but a old Angel eye
that has burnt out. On each side of bulb there is one very long screw that needs to be
unscrewed with a Torx T-15. Unscrew and remove Positive and Negative wires.
Place old bulb off to side and continue onto Process 5.
Process 5:
Connect in New BMWLED Angel Eye.
Blue Wire=Positive
White Wire=Negative
Tested and works perfectly! Time to reassemble by moving onto Process 6.
Process 6:
Screw assembly back into using original screws or use the ones provided in the kit
Now check to make sure both rings are illuminated properly. Check!
Process 7:
Put back plastic housing back on
(Looking at the housing, make sure the plastic piece with the circular hole in it is in
the top right position. This is the correct way when placing it back onto the car)
Process 8:
Reinstall wheel well
Place wheel back on and do not forget to torque your wheels! Enjoy the new bright
white Angel Eyes 