1-800`-833-0732 - General Pneumatic

IJB1JBf1JJjJ lJB!JjJJ1J1Je
-f!J!JJ~
for riveting,swagimQ,
;fl;Q;:I\e
p:u:ncfling,stakingand inserting captivehardware.
"
Manufacturer of Riveting and Insertion Tools and Accessories
1-800'-833-0732
.
www.generalpneumatic.com
email: [email protected]
2.
INTRODUCTION
When selecting a tool from this catalog be guided by the requirements
of the workpiece and the
largest fastener or rivet to be installed. Tool selection is normally based upon access to the
workpiece and maximum power required. The maximum power capability of each tool is
specified along with a photograph and other pertinent data.
Tool requirements for riveting are determined by rivet diameter and material type such as
copper, steel, titanium, aluminum, monel, etc., and whether solid or semi-tubular. In the case of
captive hardware such as studs, threaded inserts, floaters, stand ofts, etc., diameter and
material type must be considered.
General Pneumatic Tools are light, easy to hold and simple to operate. All are essentially
noiseless expect for the muffled exhaust. All General Pneumatic Tools function as squeezers,
not as hammers. This squeezing action whether in a hand held or stationary tool is deemed
necessary to produce the vital cold metal flow essential for proper retention of captive
hardware. These same characteristics
assure uniformity required to meet the rigid specifications of MIL-403B.
Whether your requirements
are for the military, aerospace, airline
assured the finest quality and value available anywhere in the world.
or commercial
you are
Elsewhere in this catalog you will find general information pertaining to rivets of all types used
throughout the United States. In addition we have included complete information on tooling for
these rivets.
RIVETING
What You Should
Know About Our Pneumatic
We suggest that our adjustment
procedure
period of many years and it works.
be followed
Compression
Tools
closely because it has evolved over a
1.
Air Line Pressure remains fixed at 90-100 pounds.
(DO NOT ATTEMPT TO CONTROL THE SQUEEZE WITH AIR PRESSURE.)
2.
The RAM or Anvil will bottom out at precisely the same point on every cycle.
3.
Full power is developed
4.
The precise squeeze is obtained
5.
The proper gap is obtained
use of spacer shims.
during the final1/16th
by adjusting
by selecting
inch of the RAM travel.
the gap between Anvils at end of stroke.
squeezer sets of the proper length and with the
How To Preset The Tool For A
Specific Rivet
EXAMPLE: To squeeze a flat head rivet 1/8th inch dia. X 1/4 inch long STEP NO.1: Insert 2 flat squeezer sets in the tool. Apply air and measure the gap between sets
at end of stroke. This gap should always measure slightly less than the length of the rivet. Flat
squeezer sets are graduated in 1/16 inch increments from 1/8th thru 1 inch in length. All other
squeezer sets are graduated in 1/8th inch increments.
Make a trial squeeze on scrap material. If more squeeze is needed, add a shim under the head of
either set. Hardened shims are available for this purpose in three increments: 1/64th inch,
1/32nd inch, and 1/16th inch. This system allows adjustment between squeezer set increments.
The gap at end of stroke is important, if too small the tool will stall. Keeping in mind that full
power is obtained during the final1/16th
inch of RAM travel.
Because the tool cannot squeeze beyond the end of travel it is therefore possible to squeeze
even the tiniest rivet or fastener precisely without damage to the workpiece. It's all in the gap
adjustment.
POPULAR RIVET HEAD STYLES & STANDARD
Example: AN-470 - AD-4-.8
AN - When these two letters
precede numbers, they
indicate Army and Navy
specifications.
MS - When these two letters
precede numbers, they
indicate Military
Standard specifications.
470 - The first three numbers
ind icate the type of head:
470 = universal head,
430 = round head, etc.
AD - Letters following head
type code indicate
material: A = 1100 (2S)
aluminum, AD =2117-T4
(A17ST) , etc.
4 - First numbers after
material code indicate
diameter of rivet in
32nds of an inch.
4::: 4/32" or 1/8",
12 = 12/32" or 3/8", etc.
8 - Last numbers indicate
length of rivet in 16ths
of an inch: 8 = 8/16" or
1/2",10 = 10/16" or
5/8", etc.
A
1100
(25)
NO MARK
AD
2117-T4
(A175T)
Rivel
ShankDiameter
Lto
ROUND HEAD
AN430AD
MS20426A
MS20470A
AN455A
TIo UO LJo ITo ITo
100 C'SUNK
UNIVERSAL
BRAZIER
FLAT HEAD
MS20426AD'
MS20470AD
AN455AD
AN442AD
100' C'SUNK
UNIVERSAL
BRAZIER
FLAT HEAD
D
AN430D
MS20426D
MS20470D
AN455D
AN442D
2017-T4
'ITo
UOI ITo
RAISED DOT
ROUND HEAD
100' C'SUNK
UNIVERSAL
DD
2024-T4
AN430DD
MS20426DD
MS20470DD
(245T)
RAISED
DOUBLE DASH
,
B
5056
(565)
UO
ROUND
HEAD
AN430B
BRAZIER
FLAT HEAD
AN455DD
AN442DD
C'SUNK
UNIVERSAL
BRAZIER
MS20426B
MS20470B
AN455B
100'
AN456D
MODIFIED
BRAZIER
AN456DD
MODIFIED
BRAZIER
FLAT WF:AD
AN4428
AN456B
UG TIe UG u0 LTo TIe
UNIVERSAL
BRAZIER
FLAT HEAD
MS20615CU
AN420C
AN441C
100' C'SUNK
C
MS20435C
MS20427C
NO MARK
ROUND HEAD
100' C'SUNK
UNIVERSAL
90' C'SUNK
F
MS20435F
MS20427F
MS20613F
AN420F
STAINLESS
STEEL
MODIFIED
BRAZIER
TIo UO 1fo ITo Uo
ROUND HEAD
.".
AN456AD
UO LTo TIo
RAISEDCROSS
COPPER
MODIFIED
BRAZIER
UO UO Lto uO LTo LTo
ROUND HEAD
(175T)
AN456A
AN442A
DIMPLE
NO MARK
It may be helpful to know just
how much a rivet should be
squeezed. This is general information and may not apply
in specific cases. (Information
on semi-tubulars
is listed
separately). The upset or shop
head should fall within the
limits of our table.
AN430A
3.
HEAD MARKINGS
MODIFIED
BRAZIER
UO UO Lto UO ITo
FLAT HEAD
AN441f
UO UO ITo uO 'ITo
ROUND
HEAD
100'
C'SUNK
UNIVERSAL
C'SUNK
FLAT HEAD
AN420M
AN441M
90'
",
M
MONEL
NO MARK
STEEL
RECESSED
TRIANGLE
MS20435M
MS20427M
MS20615M
UO UO ue Uo LTo
ROUND HEAD
100' C'SUNK
UNIVERSAL
90' C'SUNK
FLAT HEAD
MS20435
MS20427
MS20613
AN420
AN441
U0 U0 U0 UO 'ITo
ROUND
HEAD
100' C'SUNK
UNIVERSAL
Min.
Max.
HeadHeight
Min.
Max.
ShopHeadDiameter
1/16
.063
.08
.11
.02
,04
3/32
.094
.12
.16
.03
.06
1/8
.125
.16
,21
.04
.08
5/32
.156
.20
.27
.05
.10
3/16
.188
.24
.32
.06
.12
1/4
.250
.33
.43
.08
.17
5/16
.313
.41
.53
.11
.21
3/8
.375
.49
.64
.12
.25
90'
C'SUNK
FLAT HEAD
DIA.
-1
r- SHOPHD.HEIGHT
In this catalog, we have listed correct tooling (squeezer sets) for all American made rivets. A single item is referred to as a
set. Two sets are required to upset any rivet. Normally one will be flat and the other will be selected to properly nest the
head of the rivet. If there is any question as to the proper tooling check the MS or AN number. If this is not available
compare the head shape with the drawings.
4.
SQUEEZER
SETS
FLATS
(ROUND HEAD AN-430 CONTINUED)
IT
TI
(BUTTON
HEAD AN-435
CONTINUED)
1/16
1/16
1/16
1/16
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
5/32
5/32
5/32
5/32
5/32
5/32
5/32
5/32
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
BodvDiameter
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
1/2
Shank
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
Lenoth
1/8
3/16
1/4
5/16
3/8
7/16
1/2
9/16
5/8
11/16
3/4
13/16
7/8
15/16
1 Inch
1/8
3/16
1/4
5/16
3/8
GP200604
GP200605
GP200606
GP200607
200601X
200601
200602
200603
200604
200605
200606
200607
200608X
200608
200609
200610
200611
200612
200613
200614
200615X
200615
200616
200617
200618
200619
200620
200621
200321
200322
200323
1/2
1/2
1/2
3/16
3/16
3/16
7/16
1/2
9/16
200622X
200622
200623
3/16
3/16
3/16
3/16
3/16
3/16
1/8
1/4
3/8
200324
200325
200326
200327
200328
200329
200330
200331
200332
200333
200334
200335
200336
200337
200338
200339
200340
200341
200342
200343
1/2
1/2
1/2
1/2
1/2
1/2
1/2
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
5/8
11/16
3/4
13/16
7/8
15/16
1 Inch
1/8
3/16
1/4
5/16
3/8
7/16
1/2
9/16
5/8
11/16
3/4
13/16
7/8
200624
200625
200626
200627
200628
200629X
200629
200630
200631
200632
200633
200634
200635
3/16
3/16
3/16
3/16
3/16
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
AN-442
FlatSetsPI.#
200301
200302
200303
200304
200305
200306
200307
200308
200309
200310
200311
200312
200313
200314
200315
200316
200317
200318
200319
200320
AN-426
& AN-427
200344
200345
200346
200347
200348
200349
200350
3/4
3/4
1Inch
1Inch
1Inch
1Inch
1Inch
3/16
3/16
3/16
3/16
3/16
3/16
3/16
15/16
1 Inch
1/8
3/16
1/4
5/16
3/8
200351
200352
200353
200354
200355
200356
200357
200358
200359
200360
200361
200362
200363
200364
200365
1 Inch
1 Inch
1 Inch
1 Inch
1 Inch
1 Inch
1Inch
1 Inch
1Inch
1 Inch
#2PEM
#4PEM
#6PEM
#8 PEM
#10PEM
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
7/16
1/2
9/16
5/8
11/16
3/4
13/16
7/8
15/16
1 Inch
1/2
1/2
1/2
1/2
1/2
HEAD
LJ
AN-435
Bu"onHeadPt.#
GP200
601X
GP200
601
GP200
602
GP200
603
RivetSize
1/16
1/16
1/16
1/16
CONTINUED
Shank
3/16
3/16
3/16
3/16
Lenoth
1/8
1/4
3/8
1/2
1/8
1/8
3/16
3/16
3/8
1/2
200011
2O!J012
200013
200014
200015X
200015
200016
200017
200018
200019
200020
200021
200022X
200022
200023
200024
200025
200026
200027
200028
200029X
200029
200030
200031
200032
200033
200034
200,035
1/8
1/8
1/8
1/8
5/32
5/32
5/32
5/32
5/32
5/32
5/32
5/32
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
UNIVERSAL
ROUND HEAD
HEAD
TI
AN-470
UniversatHd. PI. #
GP200201X
GP200201
GP200202
GP200,203
Rivet Size
1/16
1/16
1/16
1/16
Shank
3/16
3/16
3/16
3/16
Lenoth
1/8
1/4
3/8
1/2
GP200,204
GP200,205
GP200206
GP200
207
200201X
200201
200202
1/16
1/16
1/16
1/16
3/32
3/32
3/32
3/16
3/16
3/16
3/16
3/16
3/16
3/16
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
3/32
3/32
3/32
3/32
3/32
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
5/32
5/32
5/32
5/32
5/32
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
BodvDiameter
Shank
GP20001X
GP200001
GP200002
1/16
1/16
1/16
Lenoth
200203
200204
200205
200 206
200207
200208X
200208
200209
200210
200211
200212
200213
200214
200215X
200215
200216
200217
200218
3/16
3/16
3/16
1/8
1/4
3/8
200219
200220
200221
5/32
5/32
5/32
3/16
3/16
3/16
3/4
7/8
1 Inch
GP200003
GP200004
GP200005
GP200006
GP200007
200001X
200 001
200002
200003
200 004
200 005
200006
200 007
20008X
200008
200009
1/16
1/16
1/16
1/16
1/16
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
1/8
1/8
1/8
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
200222X
200 222
200 223
200224
200,225
200 226
200227
200 228
200229X
200 229
200 230
200231
200 232
200 233
200234
200,235
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/8
1/4
1/2
5/8
3/4
7/8
1 Inch
lJ
AN-430
RoundHeadPI.#
BUTTON
200009
200010
CONTINUED
r
5.
TOOLING FOR SEMI-TUBULAR & SOLID RIVETS
COMMON HEAD STYLES
MOD. BRAZIER HD.
BRAZIER HD
TYPICAL SEMI-TUBULAR
RIVETDIMENSIONS
1
Bodv
Dia.
0.060
Head
Dia.
0.109
ClinchAllowance
0.032
HoleDia.
0.067
2
3
4
5
0.066
0.088
0.098
0.125
0.109
0.141
0.188
0.218
0.032
0.045
0.055
0.062
6
0.070
0.093
0.104
0.128
0.125
0.250
0.062
0.128
0.141
0.141
0.141
0.141
0.188
0.188
0.188
0.188
0.188
0.219
0.250
0.250
0.313
0.281
0.234
0.312
0.312
0.359
0.312
0.359
0.375
0.359
0.469
0.438
0.438
0.469
0.563
0.062
0.093
0.093
0.093
0.093
0.110
0.110
0.110
0.110
0.110
0.140
0.156
0.156
0.188
0.128
0.152
0.152
0.152
0.152
0.196
0.196
0.196
0.196
0.196
0.234
0.265
0.265
0.328
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0.125
I
\
FLARING
RivetDiameter
1116
1/16
1/16
1/16
1/16
1/16
1/16
1/16
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
5/32
5/32
5/32
5/32
5/32
5/32
5/32
5/32
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
5/16
5/16
5/16
5/16
5/16
5/16
5/16
5/16
Shank
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
----.m.o.
Lenoth
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
I
- - - -..,- - -
OR
BodvDiameter
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
5/32
5/32
5/32
5/32
5/02
5/32
5/32
5/32
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
114
1/4
1/4
1/4
1/4
1/4
1/4
1/4
...,.
I
AN-456
- _J
FOR AN-450
SEMI-TUBULAR
RIVETS
MODIFIED BRAZIER
AN-456
BRAZIER
AN-455
BrazierHd.PI.#
GP200101X
GP200101
GP200102
GP200103
GP200104
GP200105
GP200106
GP200107
200101X
200101
200102
200103
200104
200105
200106
200107
200108X
200108
200109
200110
200111
200112
200113
200114
200115X
200115
200116
200117
200118
200119
200120
200121
200122X
200122
200123
200124
200125
200126
200127
200128
200129X
200129
200130
200131
200132
200133
200134
200135
I
AN-455
ROLLING DIE 2005
FLARING DIE FOR
SEMI-TUBULAR AN-450 RIVETS.
Semi.Tubular
PI.#
GP200
501X
GP200
501
GP200
502
GP200
503
GP200
504
GP200
505
GP200
506
GP200
507
200501X
200501
200502
200503
200504
200505
200506
200507
200508X
200508
200509
200510
200511
200512
200513
200514
200515X
200515
200516
200517
200518
200519
200520
200521
200522X
200522
200523
200524
200525
200526
200527
200528
200529X
200529
200530
200531
200532
200533
200534
200535
200536X
200536
200537
200538
200539
200540
200541
200,542
...
Shank
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
Lenoth
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
Mod.BrazierHd.Pt.#
GP200401X
GP200401
GP200402
GP200403
GP200404
GP200405
GP200406
GP200407
200401X
200401
200402
200403
200404
200405
200406
200407
200408X
200408
200409
200410
200411
200412
200413
200414
200415X
200415
200416
200417
200418
200419
200420
200421
200422X
200422
200423
200424
200425
200426
200427
200428
200429X
200429
200430
200431
200432
200433
200434
200435
RivetSize
1/16
1/16
1/16
1/16
1/16
1/16
1/16
1/16
3/32
3/32
3/32
3/32
3/32
3/32
3/32
3/32
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
5/32
5/32
5/32
5/32
5/32
5/32
5/32
5/32
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
Shank
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
3/16
Lenoth
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
1/8
1/4
3/8
1/2
5/8
3/4
7/8
1 Inch
.- l
6.
SELECTING A YOKE
C-YOKE NOMENCLATURE
Four factors will determine how to select the
proper yoke for your application.
1.
The gap dimension
("B") on our yoke
drawing, the length of your rivet determines minimum gap.
2.
The reach (dimension "A") edge distance
determines reach.
3.
Allowances must be made for rivet material
such as aluminum, brass, copper, steel,
stainless steel, monel and whether solid or
semi-tubular. The rivet diameter directly
affects your choice of yoke.
A
B
C
D
Reach
Gap
Center Line Between Bolt Mounting
Set Holder Diameter
E Top Set Hole Diameter
-A.E
I
F Thickness of Yoke
G Base Height
D --./
4.
Tool power rating (maximum
force).
compressive
Because of these variables ouryokes are manufactured as either light or heavy duty types.
All General Pneumatic yokes are made of
chromemoly steel, precision machined, heat
treated and ground for long life.
In general it's best to select a yoke with the
smallest gap and shortest reach consistant with
your application. Go as light as possible. It
saves both weight and money.
As the rivet length increases it is necessary to
increase the gap of the yoke. Consult our chart
for gap requirements based on rivet length.
RIVETLENGTH
A
1-1/2
2
2-1/2
3
3-1/2
B
1-i /4
1-1/4
1-1/4
1-1/2
1-1/2
1
I
.--
TF
r--c
C-YOKE TYPES
STANDARD
Yoke
PartNo.
060,000
060,001
060,002
060,004
060,005
Holes
C
1-5/16
1-5/16
1-5/16
1-5/16
1-5/16
D
3/8
3/8
3/8
3/8
3/8
E
3/16
3/16
3/16
3/16
3/16
F
9/16
9/16
9/16
1
1
G
1
1
1
1-1/4
1-1/4
ALLIGATOR NOMENCLATURE
A Reach
B Total Yoke Gap
C Closed Height
D Set Hole Diameter
D
MINIMUM
GAP
1/4"
1-1/4"
1/2"
1-1/2"
3/4"
1-3/4"
1.00"
2.00"
1.25"
2.25"
1.5"
2.50"
1.75"
2.75"
2.00"
3.00"
It can be readily seen that the minimum
STANDARD
yoke
gap must always be one inch greater than the
longest rivet. This allows for two 1/4 inch high
rivet sets and a 1/16th squeeze on the rivet plus
the stroke of the tool.
PartNo.
275,001
285,001
275,002
285,002
275,003
285,003
275,004
285,004
275,005
285,005
275,006
285,006
.
.
Jaw
MovinQ
Stationary
MovinQ
Stationary
MovinQ
Stationary
MovinQ
Stationary
MovinQ
Stationary
MovinQ
Stationary
ALLIGATOR TYPES
A
1-1/2
1-1/2
1-1/2
1-1/2
2-1/4
2-1/4
2-1/4
2-1/4
3
3
3
3
B
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
7/8
C
1-5/8
1-5/8
1-5/8
1-5/8
1-3/4
1-3/4
1-3/4
1-3/4
2-1/8
2-1/8
2-1/8
2-1/8
D
3/16
3/16
1/4
1/4
3/16
3/16
1/4
1/4
3/16
3/16
1/4
1/4
7.
General Pneumatic Tools
6000 CHP
TOOLING
~
;~~(')
sfi
u
m,~
;~;
*0
0"
" f 'w
KIT
Uni",," Thmad Sy,,<em
'H
f~l
v
"'
'
ces'i;d) cesy
6
~02
0
e.02
'"
DC"
W-02
O.
""..
Shown
With Standard 3" Reach Yoke.
The 6000 CHP - this is our most powerful hand tool. Employing a twin tandem cylinder design,
developing in excess of three tons squeezing force, this easy to handle tool can function as a
hardware insertion press or as a hi-power riveter. To ensure flatness the 6000 CHP is fitted with a
special extra heavy duty yoke with increased gap. It accommodates
studs up to one half inch in
length as well as threaded inserts, floating nutplates, standoffs, etc. This unit comes complete with
special tooling for No.2, 4, 6, 8,10 studs and 2, 4, 6, 8,10 threaded inserts. This versatile tool with
proper tooling can be easily adapted to most all captive press-in-style
hardware. The tooling is
organized and shipped in an attractive custom fitted wooden box.
8.
General Pneumatic Tools
3000 A
Shown With 1-1/2" Reach Jaws.
The Model 3000 A is a lightweight single cylinder alligator type tool designed for applications
requiring special access. The 3000 A can be fitted with interchangeable
jaws. It is powerful, easy to
handle and comfortable to use. In many applications this is the ideal tool. Jaws are interchangeable
with the 6000 A.
Maximum Rivet Diameter 1/8" Aluminum 3/32" Steel
9.
General Pneumatic Tools
6000 A
Shown
With 3" Reach Jaws.
The 6000 A alligator type employs a twin tandem cylinder for added power. This design provides
maximum power in a lightweight easy to handle tool. It can be fitted with optional size alligator jaws.
This tool utilizes standard squeezer tooling for rivets and threaded inserts. The 6000 A is our most
powerful alligator tool. All jaws are interchangeable with the Model 3000 A tool.
Maximum Rivet Diameter 3/16" Aluminum 5/32" Steel
10.
General Pneumatic Tools
3000 C
Shown
With 1-1/2" Reach Yoke.
The Model 3000 C Hand Held Tool - is a single cylinder, powerful, and yet lightweight handheld
compression tool used primarily for riveting, and inserting captive hardware. Among it's many other
uses are swaging, staking and numerous other applications making this our most popular hand held
tool. It is available in a wide variety of interchangeable
"C" yokes.
Maximum Rivet Diameter 1/8" Aluminum 3/32" Steel
11.
General Pneumatic Tools
6000 C
Shown
With 1-1/2" Reach Yoke.
The Model 6000 C Hand Held Tool features a lightweight twin tandem cylinder for added power.
Developing 6000 Ibs. total compressive force, it provides maximum power at minimum weight.
Compact and easy to handle, this tool is first choice where additional power is required. The 6000 C
utilizes interchangeable
"C" yokes. (Yokes are also interchangeable
with the Model 3000 C).
Maximum Rivet Diameter 3/16" Aluminum 5/32" Steel
12.
General Pneumatic Tools
8000 CSA
,f
The 8000 CSA is a heavy duty high power stationary tool offering unparalled versatility. The deep
reach, 9-1/2" or optional 12-1/2" yoke provides a system that will accommodate the vast majority of
workpieces.
13.
General Pneumatic Tools
8000 CSA
STANDARD ACCESSORY GROUP
I
"A" TOOLING KIT
........
....-...
"B" TOOLING GROUP
The 8000 CSA system includes the standard accessories group including the flanger, standard and
special tooling bars. Tooling bar spacer, wrenches, squeezer sets, spacer shi ms, adjustable
mandrel and other miscellaneous hardware items.
Everything is useful in many ways to
accommodate the nearly infinite number of special demands of the workpiece.
The 8000 CSA accepts standard squeez~r tooling for rivets of all descriptions including semitubular and eyelets. The unique design of the 8000 CSA offers precise pressure settings and stroke
control which guarantees first quality finished work. The 8000 CSA provides a smooth squeezing
action necessary to generate proper cold metal flow. All hardware manufacturers emphasize the
necessity for cold metal flow to assure proper retention of captive hardware and in most cases
caution against attempting hardware installation with a hammer blow.
The 8000 CSA is equipped with our standard heavy duty foot control FC-1 and guard, thereby
freeing the operators hands for workpiece manipulation. Shipped complete and ready for use.
14.
General Pneumatic Tools
3000 AS
Model 3000 AS - This unique tool may be ideal foryourspecial dedicated assembly requirements. It
features a single cylinder, alligator type with our standard stroke adjustment. It is designed for foot
control FC-2, and simple bench mounting. Assemblers hands are freed for easy workpiece
manipulation. A large selection of standard squeezer tooling is readily available for small solid and
semi-tubular rivets, eyelets, and many types of captive hardware. It can be fitted with optional,
interchangeable alligator jaws. See optional alligator jaw table on page 6.
3000 CS
I
The 3000 CS - This is one of our most
popular bench mounted tools for handsfree operation. It employs a single cylinder
compression unit. The 3000 CS is fitted to
a heavy duty stationary
"C" yoke. The
adjustable mandrel permits simple, precise
pressure settings. It is ideal for eyelets,
solid and semi-tubular rivets, plus captive
hardware of all kinds. With proper tooling,
it is also ideal for staking and swaging. The
3000 CS incorporates
the handy stroke
control adjuster. Equipped with foot control FC-2 and guard, all hoses, hardware,
and connectors. Shipped completed, ready
to operate. See specifications
on page 6.
15.
General Pneumatic Tools
6000 ASI
' "
''
"'
i
'" 11,"'.. ..~
".',~
.-".
.." .' . . .. .' '.."
,,«,Im
,/
,
,
,
,
'
,
,
,
,,
,
, ,,,"",,,,ffIi, ,,
,J
'.'
." .'..
.
.'
.
.
"",..,.,
.'...
,
"
"","'".,.-;;j
'..
.. '. '.'
", ,
,
,
The Model 6000 AS is our high powertwin tandem alligator type featuring unique adjustable stroke
control. It is designed for simple bench mounting. It is portable and easy to set up, and like all
General Pneumatic Tools, is near noiseless making it ideally suited to work in confined areas. The
added power makes this one of our most versatile tools. It is perfect for riveting and inserting captive
hardware. Shipped with bench mount, foot control FC-2 and guard plus all hoses and connectors
ready to operate. See optional alligator jaw table on page 6.
6000 CS
The 6000 CS is a twin tandem cylinder
compression
unit mounted on a heavy
duty bench type "C" yoke. It is intended
for very small to medium diameter rivets
and captive hardware. Its simple hands
free operation
allows easy workpiece
handling. It also features our unique stroke
control. The 6000 CS is shipped complete
with foot control FC-2 and guard plus all
hoses, connectors and necessary hardware
ready to operate. See specifications
on
page 6.
,
16.
General Pneumatic Tools
8000 CS
~
Model 8000 CS power unit is identical to the 8000 CSA power unit. The difference is in the yoke and
tooling accessories. The 8000 CS is normally used where high power is required but not a large
yoke. This tool is used for staking, swaging, punching, riveting or pressing in captive hardware.
Although this is a hi-power tool, it can also be used for the lightest and most delicate work. As with
all General Pneumatic Tools, a maximum power rating is specified. With proper adjustment any
fraction of the maximum rating is at the operators command. This unit can be tooled for your
specific needs. Shipped complete with our FC-1 foot control and guard, adjustable mandrel, plus all
hoses and connectors. Ready to operate.
17.
General Pneumatic Tools
15 KCS
Model15 KCS - This is our largest, heaviest and most powerful machine. Despite the size and weight
it offers the widest power range of any General Pneumatic Tool. The squeezing force, ranging from
less than an ounce to seven and one-half tons is infi nitely adjustable and under di rect control of the
operator. When properly tooled and adjusted it will render consistently accu rate fin ished work. It is
capable of meeting the most rigid specifications.
This machine can be used for swaging, staking,
hole punching, riveting and pressing in captive hardware. The 15 KCS can be fitted to any of our
standard yokes. If your needs are special we will build a special tool to meet your requirements.
Shipped complete with our FC-1 foot control and guard, adjustable mandrel, all hoses, fittings and
connectors ready to go.
18.
FOOT CONTROLS
FC-4
FC-3
4-WAY VALVE
FOR
8000 CS
8000 CSA
15 KCS
3-WAY VALVE
FOR
3000 AS
6000 AS
3000 CS
6000 CS
Each stationary tool is equipped with either our FC-1 or FC-2 foot control and guard, all hoses and
connectors.
Each foot control is supplied with a heavy duty ribbed rubber base.
A 1/4" NPT female fitting is provided for simple adaption to your air system.
These foot control valves are designed for heavy duty everyday use. They are simple and reliable.
As an added safety feature, all tools REVERSE DIRECTION IMMEDIATELY when the operator's
foot is removed.
19.
A PARTIAL LIST OF OUR SATISFIED CUSTOMERS
Ford Motor Co.
Lockheed Aircraft
Allen Bradley
U.S. Navy
Borg Warner
ITT Cannon
Boeing Airplane Co.
Litton Industries
TRW - TECHNAR
Northrop
Ai r Research
Hughes Aircraft
Co.
Teleflex Defense Systems
GRACO
Kim Lighting
Penn Engineering
Bega Lighting
Grumman Aircraft
Norman Enterprises
North American
Co.
Rockwell
Peavey Electronics
Johnson Controls
Crouse Hinds
Wire Forms
National Magnetics
Roh r Ai rcraft
Superform
Comet Trailers
Skat Enterprises
Bedline
Teledyne Ryan
Control
Cipher Data
Motorola
Arrowsmith
Kaman Aerospace
Westinghouse
General Electric Co.
& Mfg. Corp.
Devices Inc.
Garrett Engine Div.
Turbine Metal Tech.
Plastics Research
NASA
Hartzell Mfg. Co.
Arco Solar
Jet Propulsion Labs
M & J Metalcraft
Cable Link Corp.
UNARCO
Breed Corp.
Woodbine Products
AGM Container
General Dynamics
Micro Computer
Superior
Corp.
Fireplace
Accessories
!JB1JHf1JJjJlJB!J1JJ1JJ]!j-SJJJJJ0
tur,riv,ef'ing,
swaging,hl,le'punching,stakin.g
andinsertingcaptivehardware.
Pictured
is our Model
8000CSA riveter/insertion
tool featuring ourdeep reach
12%" heavy duty "c" yoke.
The mounting pedestal incorporates built-in filter,
lubricator and regulator. It is
shipped complete with all
hoses, connectors and air
fittings. It requires 90-100
PSI air connection.
*
Also available
with 9%"
reach.
**The mounting pedestal is
optional equipment.
IManufacturerof Ri.vetingand Insertion Tools and Accessories
!ForFurtherInformation Contact:
r
GENERAL PNEUMATIC TOOLS ~
4591 w. SELWAY. POST FALLS, IDAHO 83854 u.S.A.
1.800.833.0732
'--
(208) 773-8080
Fax (208) 773-6918
~