Sunpentown Int`l Inc. Please retain this instruction booklet for future

SB-2025L (elongated)
SB-2025S (round)
Sunpentown Int’l Inc.
Please retain this instruction booklet for future references.
Grounding Instructions
6) Never block air vent openings, Keep air vents free of lint, hair, dust and other particles.
7) Do not use product while drowsy or sleepy to reduce the possibility of falling asleep while seated on
the unit.
not
Water supply should not be ground water or industrial water.
Flexible pipe
to bidet
L-Fitting x 2
1. Check that the bidet fits on the toilet.
2. Check that the toilet shutoff valve is working properly.
3. There is small amount of water in the tank.
Step 1: Shut off water valve, drain toilet tank by flushing the toilet. Remove the flexible pipe connected
to toilet tank. (Diagram 6)
Step 2: Remove the existing toilet seat and cover by removing the mounting nuts and bolts.
Step 3: Install mounting plate as shown. Make necessary adjustments to fit the two mounting holes.
(Diagram 5)
Step 4: Attach T-Valve to the water shutoff valve as shown. (Diagram 6)
Step 5: Attach flexible pipe – A connecting the T-Valve to toilet tank. (Diagram 6)
Step 6: Mount the bidet by aligning the grooves underneath the main body to that on the base plate.
Slide the main body onto base plate until it “clicks. (Diagram 7)
If water filter will be installed:
Step 7:
• Attach one L-Fitting to each end of the water filter. (Diagram 6)
• Connect a flexible hose from the T-Valve to the L-fitting below the water filter. (Diagram 6)
• Connect second flexible hose from the L-fitting above the water filter to the bidet. (Diagram 6)
If water filter will NOT be installed:
Step 7: Attach flexible pipe – B connecting the T-Valve to the bidet. (Diagram 6)
Step 8: Check that the unit is seated properly on the toilet and tighten the nuts and bolts once bidet is in
desired position.
Step 9: Plug in power cord and check that unit is functioning properly.
Note: Save the old toilet seat and cover so that the toilet may be restored to its original condition when
desired.
[without water filter]
Initial Usage
1.
Connect power and bidet will turn on automatically.
2.
Allow 1-2 minutes for the water tank to fill.
3.
Activate the bidet by sitting on the seat.
4.
Press and hold the WASH/MOVE button for about 2 seconds until nozzles begin to spray.
5.
In rare cases the spray may not start due to air blockage in water pump. Try gently tapping the
control panel to help release trapped air.
Note: Bidet has a built-in pressure sensor (refer to Diagram 1). When a child uses the bidet and their
weight is not enough to activate bidet, the supervising adult can apply pressure with their to the right
side of the seat (when facing the bidet).
STOP
Stops all functions when pressed.
Press WASH button for regular wash, press again to have
nozzle move back and forth during wash. Function
automatically stops after 50 seconds.
WATER PRESSURE/AIR TEMPERATURE
In washing functions: press HI or LOW to adjust water
pressure.
In drying functions: press HI or LOW to adjust air
temperature.
Press BIDET button for feminine wash, press again to have
nozzle move back and forth during wash. Function
automatically stops after 50 seconds.
Cleaning
This bidet is made of antibacterial resin to control the spread of germs. The nozzles have a self-cleaning
function. Nevertheless, routine cleaning is advised. Use mild detergents and a sponge or soft cloth to clean
the exterior of the unit.
Before cleaning the nozzle heads, unplug the power cord. Hold the end of the washing nozzles and pull out
gently to clean them. They may be scrubbed gently with a soft toothbrush. Be sure that the nozzle hole is
not damaged or obstructed during cleaning. (see below)
Water Tank Maintenance
The water in the water tank should be replaced whenever unit has not been used for a while or after water
service has been interrupted. Unplug unit and turn off the water. Place a large receptacle below the drainage
cap and remove the cap to drain water completely (see diagram 2).
Removing the bidet unit
In case the bidet needs to be removed, just press the Quick Release button ad slide the main body off the
base plate as shown.
Check that the water pressure meets the required psi of 15.65 psi. Spray may be
weak when pressure falls below 15.65 psi.
ON.
Find the source of the leak (the connection points at the T-Valve or the toilet tank). Apply Teflon
tape to thread and fasten nut tightly.
• The tank capacity of warm water is 2.75
pints. Water temperature can be
adjusted to 4 levels press WATER
TEMP button to change.
• It takes 3~5 minutes to achieve the set
temperature.
Product Specifications
Model
SB-2025S
SB-2025L
Power supply
120V / 60Hz
Power consumption
600W (max)
Power cord length
4 ft. / 1.2 m (max)
2
Water pressure range
7.11 ~ 106.7 psi (0.5-7.5 kg f/cm )
Water supply method
Direct connection to tap water
Water supply control
By solenoid valve
Dimension
Weight
12.1 lbs
Fuse
7A (contact breaker inside)
Water tank capacity
Wash
Bidet
Water pressure
Temperature
Cleansing
Nozzle position
Temp control
Heater
Safety device
Temperature
Temp control
Heated seat
Heater
Spray volume: max 2.75 pt/min
Wash & bidet at 8 levels, adjusted by Micom
Adjustable at 4 levels: room temp, 93°F, 99°F, 104° F
(Room temp ~ 107.6°F)
Adjusted by Micom, along with Move, Massage, Water
pressure
Controlled by Micom: Room temp ~ 107.6°F
550W
Bimetal, thermal fuse, overheat prevention circuit
Adjustable at 4 levels: room temp, 93°F, 99°F, 104° F
(Room temp ~ 107.6°F)
Adjustable at 4 levels: Room temp ~ 107.6°F
45W
Damper (slow down) shock absorber by ABS oil pressure
Thermistor, thermal fuse
Adjustable at 4 levels: room temp, 97°F, 102°F, 109 °F
(Room temp ~ 136.4°F)
270W
Heater
Fan
Feature
Fan
Occupied seat sensor
Installation
Spray volume: max 2.75 pt/min
Safety device
Safety device
Deodorizer
2.75 pints (1.3 liter)
Anti-slam seat
Temperature
Drying
12.1 lbs
Accessories
Filter
Thermal fuse
Low noise, strong air pressure
Ceramic deodorizing catalyst
Strong suction, low noise, strong air pressure
Touch sensor
Mounting plate 1, fixing bolt 2, nut 2, bracket 2
Flexible connection pipe 2, packing 2, T-valve connector 1
Rubber washer 2
Purifying filter, fitting 2, spare nut, flexible connection hose 2
Your Guarantee
If this product is found to be faulty as a result of faulty materials or workmanship
within one year from date of purchase, it will be repaired free of charge.
This guarantee is subject to the following terms:
• Sunpentown must be notified of the fault.
• Proof of purchase must be presented to Sunpentown’s nominated representative.
• The warranty will be void if the product is modified, misused or repaired by an
unauthorized person.
• The warranty after repair will not be extended beyond the original one-year period.
• All replacement parts will be new or reconditioned.
• Parts, which are replaced, become the property of Sunpentown.
• The warranty applies for the use of the product in the USA only.
What is NOT COVERED:
• Warranty does not include freight charges.
• Incidental or consequential damage caused by possible defects with this product.
• Damage to product caused by improper power supply voltage, accident, fire, floods
or acts of nature.
• Failure of product resulting from unauthorized modifications to the product.
• Improper installation or failure to perform the necessary maintenance.
This GUARANTEE is in addition to your Statutory Rights
SUNPENTOWN INTERNATIONAL INC.
14625 Clark Avenue, City of Industry, CA 91745
Tel: 626-336-2299 · Fax: 626-336-7116
[email protected]
www.sunpentown.com