docGroup 2 - Fluid Control AS
download 
Report Transcription
Group 2 - Fluid Control AS
Group 2 Thermoplastic Hoses Teflon Hoses Water Jetting Hoses INDEX Page Contents 3-5 2 Selection Tables for Hoses and Fittings 6 Micro Hoses, 2020N, Mini Control System thermo-plastic 7 Teflon Hoses (PTFE) 8 Medium Pressure, Type 518C, 550H Hydraulic 9 Medium Pressure, Type 540N 10 High Pressure, Type 520N, 528N Hydraulic, Gases, Non-conductive 11 High Pressure, Type 590, 575X Hydraulic 12 High Pressure, Type AS10, AS13, Hydraulic, Grease, Gases 13 High Pressure, Type HP, 2040N Hydraulic, Grease, Gases, Spray Paint 14 High Pressure, Type 2040H, 2370N/H Hydraulic 15 High Pressure, Type 2370M, 2244N, 2245N 16 High Pressure, 714 Spray Paint, Hydraulic, Type 715 Spray Paint, Hydraulic 17 Ultra high Pressure, Type 2448N (V91) Umbilical Hose 18 Ultra high Pressure, Type 2380N, 2380M, 2388N Hydraulic 19 Ultra high Pressure, Type 2X80N, 2390N (V91) Hydraulic 20 Ultra high Pressure, Type 2440D/N, 2640D/N 21 Black Eagle Family + ColorgardTM 22 Golden Eagle Family + ColorgardTM 23 Phalcon + ColorgardTM 24 Water Jetting, Type 2240D, 2240M 25 Water Jetting, Type 2388N “Blueline”, 2580N “Blueline” 26 Water Jetting, Type 2440D/N, 2440M 27 Water Jetting, Type 2640D/N 28 Water Jetting, Type 2740D, 2840D 29-33 Chemical table Symbol Key # Part No 2388N-04V12W Part No Fitting Series R mm 6.3 inch dash 1/4 -04 Inside Diameter mm 13.3 Out. Dia. bar psi 1280 18560 Working Pressure bar psi 3200 46400 Burst Pressure mm 80 B. Radius kg/m 0.30 Weight Available for rental Fluid Control is now a Approved Collaborator for Parker Hannifin. We hold in stock a wide range of thermoplastic hoses, as well as other Parker products. 2-2 Flexible Solutions BS SELECTION OF HOSES Selection Table for Hoses MpA multiplied by 10 = Bar (1 MpA = 10 Bar) Hose Dimension inch 5/64 1/8 5/32 3/16 1/4 5/16 3/8 1/2 5/8 3/4 1 1¼ 1½ 2 mm 2.0 3.2 4.0 4.8 6.4 7.9 9.5 12.7 15.9 19.0 24.4 31.8 38.1 50.8 dash -012 -02 -025 -03 -04 -05 -06 -08 -10 -12 -16 -20 -24 -32 2 3 4 5 6 8 10 12 16 20 25 32 40 50 DN Micro Hoses 2020N Working Pressure Mpa 63 53 2 Fittings Series 50 EX Medium-pressure Hoses 518C 17.5 550H 55LT 20 510A 21 19 17.5 15.5 15.5 10.5 8.5 7 51/55/56/58 22.5 21 17.5 15.5 14 10 8.5 7 55/56/58 22.5 21 17.5 15.5 14 8.5 55/56/58 21 19 17.5 15.5 14 8.5 51/55/56 High-pressure Hoses 520N 34.5 34.5 31 27.5 24 528N 34.5 34.5 31 27.5 24 19 55/56 55/56 580N 34.5 27.5 24 19 15.5 14 58 588N 34.5 27.5 24 19 15.5 14 58 21 590 34.5 34.5 27.5 24 575X 34.5 34.5 34.5 34.5 HP/HP8/HP8X 69 69 55 69 55 2022NO 57CR 2040N 17.5 14 55/56/58 34.5 34.5 55/56/58H HP NX-OF 34,5 35 2040H 34,5 CR 34 31 25 24 18.5 14 12.5 10 56/PX 34 31 25 24 18.5 14 12.5 10 56/PX 33 30 27.5 2240N 43 2245N 45 40 37,5 35 RX 2370N/2370H 46.5 44 42 35 NX/RX/9X 53.5 55 8X 57,5 55 8X 44,5 41,5 29 130 100 180 140 27.5 8X/NX Ultra-high-pressure Hoses 2244N 75 2370N 69 2380N 70 2388N 80 62.5 8X 2390NV91 2X80N 72.0 2440D/2440N 220 180 280 250 2448NV91 164 70 150 103 2640D/2640N RX 140 28 9X 90 LX 45 8X/LX 103* 210 8X/ * 69 69 5X Teflon Hoses PTFE/FEP 919U 21 2030T 27.5 2033T 91N 24 20 17.5 15 12.5 10 8 YX 27.5 25 22.5 20 17.5 15 11 PX/YX 14 12.5 10 HPX Paint Spray Hoses 714 715 35 36 31 22,5 19 34 48 38 29 PX Water Jetting Hoses 2240D 110 120 100 2380N 100 90 TX/AX 110 100 KX 2244N 86 2388N 128 2580N 2440D/2440N 220 160 140 120 180 164 150 86 KX 110 BS BL 140 130 100 90 140 120 LX 2640D/2640N 280 250 210 180 2740D 300 280 250 200 HX 400 300 250 WX 2840D HX/5X * Ask us about fittings www.fluidcontrol.no 2-3 SELECTION OF FITTINGS Selection Table for Fittings 2 NPTF Male 60° Cone NPTF Female-rigid JIC Male-37° Cone UNF Male/O-ring JIC-37° Cone Metric Swivel Strong Series 90° Elbow O-ring JIC 37°Cone 45° Elbow JIC 37°Cone 90° Elbow BSP Male-60° Cone BSP Swivel 60° Cone UNF Swivel 59° Cone BSP Swivel 45° Elbow BSP Swivel 90° Elbow Metric Swivel Light Series Cone Metric Swivel Light Series Cone 45° Elbow Metric Swivel Light Series Cone 90° Elbow Metric Swivel Strong Series Metric Swivel Strong Series O-ring Metric Swivel Light Series O-ring Metric Swivel Light Series 45° Elbow O-ring Metric Swivel Light Series 90° Elbow O-ring Metric Male 24° Cone Light Series Metric Male 24° Cone Strong Series BSP Male M16X2 Swivel (Knurled nut) BSP Swivel 60° Cone BSP Male- For USIT Ring AE Fitting High Pressure 59° Cone UNF-LH Metric Swivel Nut AE Fitting Medium Pressure 59° Cone UNF-LH AE Fitting High Pressure 59° Cone UNF-LH AE Fitting High Pressure 59`Metric cone 01 NPTF Male - 60˚ Cone 02 NPTF Female - rigid 51 54 55 56 58 5X 8X 91N 93N BL EX HP BS NX PX RX YX 51 54 55 56 58 9X 8X 91N 93N AX EX HP LX NX PX RX YX 51 54 55 56 58 BL 8X 91N 9X BS EX KX LX NX PX RX YX 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX 06 JIC - 37˚ Cone UNF Swivel Nut 92 Sealing Head (60˚) BSP Swivel Nut C3 Sealing Head Light Series Metric Swivel Nut 2-4 AB EX HP LX NX PX RX YX 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX Light Series Metric Swivel Nut X X 56 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X AB EX HP LX NX PX RX YX 5X 8X X 9X X X X X X X X X X X X X X X X X X X X 91N X X X X X X X X X X X X X X X X 05 UNF Male / O-Ring 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX 90˚ Elbow UNF Swivel Nut 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX BSP Swivel Nut 45˚ Elbow 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX 90˚ Elbow 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX Light Series Metric Swivel Nut Flexible Solutions 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX 3B BSP Male - 60˚Cone 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX B2 Sealing Head (60˚) C5 Sealing Head 51 54 55 56 58 5X 8X 91N 93N 58 X X B1 Sealing Head (60˚) 51 – AB – 54 – HX – 55 – KX – 56 – LX 113 58 – NX – 5X 69 PX – 8X – RX – 91N – YX – 93N – C4 Sealing Head 45˚ Elbow X 55 X 39 JIC - 37˚ Cone AY 59˚ Sealing Cone UNF Swivel Nut 54 03 JIC Male - 37˚ Cone 51 54 55 56 58 5X 8X 91N 93N 37 JIC - 37˚ Cone 45˚ Elbow UNF Swivel Nut 51 X 01 02 03 05 06 1C 37 39 3B 92 AY B1 B2 C3 C4 C5 C6 C9 CA CE CF D0 D2 D9 R8 UO Y9 YA YR Y2 Y4 YM BSP Swivel Nut 90˚ Elbow C6 Sealing Head Heavy Series Metric Swivel Nut SELECTION OF FITTINGS 01 NPTF Male - 60˚ Cone 93N X X AB EX X 06 JIC - 37˚ Cone X X UNF Swivel Nut X 02 NPTF Female - rigid 51 54 55 56 58 HP 5X 8X X 91N 93N BL EX HP BS NX LX PX RX YX 51 X 54 55 56 58 9X 8X 91NX 93N AX EX HP LX NX PX RX YX 92 Sealing Head (60˚) BSP Swivel Nut X C3 Sealing Head X X Light Series Metric Swivel Nut X X X X X 51 54 55 56 58 BL 8X 91N 9X BS EX KX LX NX PX RX YX 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX X X X X X X X X X X NX X PX X RX X X X 37 JIC - 37˚ Cone X X X 45˚ Elbow UNF X Swivel NutX X X X X X X X X X Cone AY 59˚ Sealing X X UNF Swivel Nut X X X X X X X X X C4 Sealing X Head 45˚ Elbow X Light Series X Metric Swivel Nut X X X X X X 03 JIC Male - 37˚ Cone 51 54 55 56 58 YX 5X 8X X 91N 93N AB EX HP LX NX AX PX RX YX 51 X 54 55 56 X 58 X 5X 8X X 91NX 93N AB EX HP LX NX PX RX YX X X X X KX BS X AB EX HP LX NX HX PX RX YX 51 54 55 56 58 5X 8X 91NX 93N AB EX HP LX NX PX RX YX 90˚ Elbow UNF Swivel Nut X X X 51 54 55 56 58 5X 8X 91NX 93N AB EX HP LX NX PX RX YX 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX X B1 Sealing Head (60˚) AB – HX – KX – LX 113 NX – PX – RX – YX X – 51 54 55 X 56 X 58 X 5X 8X 91NX 93N AB EX HP LX NX PX RX YX BSP Swivel Nut 45˚ Elbow X X Heavy Series Metric Swivel Nut ISO 12151-2 51 54 55 56 58 5X 8X 9X BL D0 Metric Male 24˚ Cone Light Series ISO 12151-2 90˚ Elbow Light Series Metric Swivel Nut X AB EX HP LX NX PX RX YX 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX Y2 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX 51 54 55 56 58 5X 8X 91N 93N Y4 High Pressure Connector 59˚ Cone UNF - Left Hand Thread 51 54 55 56 58 5X 8X 91N 93N Light Series Metric Swivel Nut ISO 12151-2 DIN 3852 Shape A AB EX HP LX NX PX RX YX 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX 59˚ Cone UNF - Left Hand Thread 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX X Heavy Series Metric Swivel Nut 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX X X 90˚ Elbow Light Series Metric Swivel Nut ISO 12151-2 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX R8 Quick Connect Fitting YA High Pressure Connector AB EX HP LX NX PX RX YX AB EX HP LX NX PX RX YX CF 24˚ Sealing Cone / O-Ring 51 54 55 56 58 5X 8X 91N 93N D9 BSP Male AB EX HP LX NX PX RX YX Y9 BSP Male - for USIT Ring Medium Pressure Connector 59˚ Cone UNF - Left Hand Thread Heavy Series ISO 12151-2 51 54 55 56 58 5X 8X 91N 93N 45˚ Elbow 51 54 55 56 58 5X 8X 91N 93N C6 Sealing Head CE 24˚ Sealing Cone / O-Ring AB EX HP LX NX PX RX YX D2 Metric Male 24˚ Cone 51 54 55 56 58 5X 8X 91N 93N U0 Sealing Head (60˚) BSP Swivel Nut Light Series Metric Swivel Nut ISO 12151-2 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX B2 Sealing Head (60˚) BSP Swivel Nut X X CA 24˚ Sealing Cone / O-Ring AX EX BS LX NX PX RX YX HX WX 90˚ Elbow C5 Sealing Head X C9 24˚ Sealing Cone / O-Ring 51 54 55 56 58 5X 8X 91N 93N 3B BSP Male - 60˚Cone 39 JIC - 37˚ Cone X 51 – 54 – 55 – 56 – 58 – 5X 69 8X – 91NX – 93N – X TX 05 UNF Male / O-Ring 51 54 55 56 58 BL 5X 8X X 91N 93N 51 54 55 56 58 5X 8X 91N 93N Metric Swivel Nut Knurled 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX YR Quick Connect Fitting AB EX HP LX NX PX RX YX Metric Swivel Nut 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX YX YM High Pressure Connector AB EX HP LX NX PX RX HX WX 59˚ Metric Cone Metric - Left Hand Thread www.fluidcontrol.no 51 54 55 56 58 5X 8X 91N 93N AB EX HP LX NX PX RX HX WX 2-5 2 THERMO-PLASTIC HOSES MICRO HOSES Type 2020N Mini Control System 2 Construction: Applications: Covering: Reinforcement: Internal: High-pressure hose for use with petroleum and synthetic hydraulic oils and gases. Special hose for Mini Control pressure measurement equipment (minimess). Supplied with fittings as specified on the next page. Max length change is +2% / -4% at working pressure. * Safety factor reduced for diagnostic applications. Black Polyamide 1 layer braided synthetic fiber Polyamide Temperature range: ÷40oC to +100oC for synthetic and oil-based hydraulic oils # Part No Fitting Series R 2020N-012V30 2020N-02V30 2020N-025V30 mm 2.0 2.9 4.0 inch 5/64 1/8 5/32 dash -012 -02 -025 mm 4.9 6.0 8.1 bar 475 400 440 psi 6885 5800 6380 bar 1900 1600 1760 psi 27550 23200 25520 mm 20 30 40 kg/m 0.016 0.023 0.042 EX EX EX 2020N-012V50 2020N-02V50 2020N-025V50 2.0 2.9 4.0 5/64 1/8 5/32 -012 -02 -025 4.9 6.0 8.1 * 630 * 530 * 500 9135 7685 7250 1900 1600 1760 27550 23200 25520 20 30 40 0.016 0.023 0.042 EX EX EX See page 5-19 for fittings Mini control system – HOSE COUPLINGS FOR USE WITH HOSE type 2020N M16x2 Screw lock coupling Part No A mm 801.10.162 19 d mm d1 mm M16x2 P.max bar 640 Coupling with pipe socket 801.32.006 801.32.008 24 24 801.50.204 801.50.208 25 25 6 8 M14x1,5 M16x1,5 640 640 1/4” BSP 1/2” BSP 640 640 Pressure gauge coupling Other sizes, thread types and materials available on request 2-6 Flexible Solutions Part No of the couplings are complete with pressure sleeve, and includes sleeve with dust plug M16x2 screw lock couplings. THERMO-PLASTIC HOSES PTFE TEFLON HOSES Type 2030T PTFE Teflon Hose 2 Construction: Applications: Covering: Reinforcement: Internal: There are currently no known solvents for PTFE. Can be used for steam, acids, alkalis, articles of food, oils and corroding oils and corroding substances. PTFE is highly resistant to natural degradation and aging and does not absorb water. The exceptional low friction resistance minimizes loss of pressure in the hoses. Type 2030T is well suited for spray painting. Stainless steel wire braid (reinforcement) 1 layer stainless steel wire braiding Polytetrafluoroethylene PTFE) Temperature range: ÷50oC to +150oC (+230oC up to 20 bar) # Part No 2030T-03V70 2030T-04V70 2030T-05V70 2030T-06V70 2030T-08V70 2030T-10V70 2030T-12V70 2030T-16V70 Fitting Series R mm 4.8 6.3 7.9 9.5 12.7 15.9 19.0 25.4 inch 3/16 1/4 5/16 3/8 1/2 5/8 3/4 1 dash -03 -04 -05 -06 -08 -10 -12 -16 mm 7.8 9.5 11.5 13.3 16.7 20.0 23.5 29.0 bar 275 240 200 175 150 125 100 80 psi 3990 3480 2900 2540 2180 1810 1450 1160 bar 1100 960 800 700 600 500 400 320 psi 15950 13920 11600 10150 8700 7250 5800 4640 mm 50 75 100 120 135 160 200 250 kg/m 0.09 0.13 0.17 0.19 0.29 0.34 0.41 0.51 BPX BPX BPX BPX BPX BPX BPX BPX Type 2033T PTFE Teflon Hose Construction: Applications: Covering: Reinforcement: Internal: There are currently no known solvents for PTFE. Can be used for steam, acids, alkalis, articles of food, oils and corroding oils and corroding substances. PTFE is highly resistant to natural degradation and aging and does not absorb water. The exceptional low friction resistance minimizes loss of pressure in the hoses. Type 2030T is well suited for spray painting. Stainless steel wire braid (reinforcement) 2 layers stainless steel wire braiding Polytetrafluoroethylene PTFE) Temperature range: ÷50oC to +150oC (+230oC up to 20 bar) # Part No 2033T-04V70 2033T-05V70 2033T-06V70 2033T-08V70 2033T-10V70 2033T-12V70 2033T-16V70 Fitting Series R mm 6.3 7.9 9.5 12.7 15.9 19.0 25.4 inch 1/4 5/16 3/8 1/2 5/8 3/4 1 dash -04 -05 -06 -08 -10 -12 -16 mm 11.0 13.2 15.0 18.8 21.5 25.5 31.0 bar 275 250 225 200 175 150 125 psi 3990 3630 3260 2900 2540 2180 1810 www.fluidcontrol.no bar 1100 1000 900 800 700 600 500 psi 15950 14500 13050 11600 10150 8700 7540 mm 75 100 120 135 160 200 250 kg/m 0.23 0.26 0.34 0.47 0.53 0.69 0.81 PX PX PX PX PX PX PX 2-7 THERMOPLASTIC HOSES MEDIUM PRESSURE Type 518C Non-conductive Hose Specifications Exceed SAE 100 R7 2 Construction: Applications: For medium-pressure hydraulic systems with petroleum or synthetic hydraulic oils, where it is required that the hose must not be electrically conductive. Well suited for hydraulic systems at highvoltage installation working platforms. Max length change is +/- 2% at working pressure. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Covering: Reinforcement: Internal: Special PFX, orange 1 layer braided synthetic fiber Polyester Elastomer Temperature range: ÷40oC to +100oC for hydraulic oils ÷40oC to +57oC for synthetic oils and water-based fluids Insulation resistance: SAE J517 (less than 50 μA leakage during 75,000 volts per foot) # Part No 518C-02 518C-03 518C-04 518C-05 518C-06 518C-08 518C-10 518C-12 518C-16 Fitting Series R mm inch dash mm bar psi bar psi mm kg/m 3.2 4.8 6.3 7.9 9.5 12.7 15.9 19.1 25.4 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 1 -02 -03 -04 -05 -06 -08 -10 -12 -16 8.6 10.7 12.0 14.5 16.0 20.6 24.9 27.4 33.5 175 210 190 175 155 155 105 85 70 2 500 3 000 2 750 2 500 2 250 2 250 1 500 1 250 1 000 690 830 760 690 620 620 420 345 275 10 000 12 000 11 000 10 000 9 000 9 000 6 000 5 000 4 000 13 19 38 44 51 76 102 152 203 0.05 0.07 0.08 0.11 0.14 0.22 0.30 0.31 0.40 58 51/55/56 51/55/56 51/55/56 51/55/56 51/55/56 51/58 51/55/56 51/55/56 Type 550H, SAE 100 R7 High Performance Construction: Applications: Covering: Reinforcement: Internal: Medium-pressure systems, also for mobile hydraulics and agriculture machinery. Also available as dual- or multi-hose or “Non-Conductive” hose. Max length change is +/- 2% at working pressure. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Black pin-pricked Polyurethane 2 layers braided synthetic fiber Hytrel Temperature range: ÷70oC to +100oC for water and water-based oils ÷40oC to +100oC for petroleum and synthetic-based oils and gases # Part No 550H-03 550H-04 550H-05 550H-06 550H-08 550H-10 550H-12 550H-16 mm inch dash mm bar psi bar psi mm kg/m 4.8 6.3 7.9 9.5 12.7 15.9 19.0 25.4 3/16 1/4 5/16 3/8 1/2 5/8 3/4 1 -03 -04 -05 -06 -08 -10 -12 -16 10.9 13.0 14.5 16.5 20.6 24.9 26.9 33.3 225 210 175 155 140 105 85 70 3250 3000 2500 2250 2000 1500 1250 1000 900 830 700 620 560 420 345 275 13000 12000 10000 9000 8000 6000 5000 4000 19 32 44 51 76 102 127 203 0.08 0.10 0.11 0.14 0.21 0.30 0.31 0.40 For more information on coupling options and quality of materials, please contact us 2-8 Fitting Series R Flexible Solutions 55/56 55/56 55/56 55/56 55/56 56/58 55/56 55/56 THERMOPLASTIC HOSES MEDIUM PRESSURE Type 540N Medium-pressure Hose Specifications Exceed SAE 100 R7 2 Construction: Applications: Medium-pressure systems for oil and synthetic hydraulic fluids and certain chemicals. Also suitable for agricultural machines, robotic systems and for use with fire resisting fluids. Max length change is +/- 2% at working pressure. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Covering: Reinforcement: Internal: Black pin-pricked Polyurethane 1 layer braided synthetic fiber Polyamide Temperature range: ÷40oC to +100oC for oil, water and synthetic hydraulic fluids # Part No 540N-02 540N-03 540N-04 540N-05 540N-06 540N-08 540N-12 Fitting series R mm inch dash mm bar psi bar psi mm kg/m 3.2 4.8 6.3 7.9 9.5 12.7 19.1 1/8 3/16 1/4 5/16 3/8 1/2 3/4 -02 -03 -04 -05 -06 -08 -12 8.4 10.5 12.6 14.1 16.0 20.1 26.3 175 210 190 175 155 140 85 2500 3000 2750 2500 2250 2000 1250 690 830 760 690 620 560 345 10000 12000 11000 10000 9000 8000 5000 13 19 38 44 51 76 152 0.05 0.08 0.10 0.12 0.14 0.21 0.25 58 55/56 55/56 55/56 55/56 55/56 55/56 Also available in twin design and as multiline. www.fluidcontrol.no 2-9 THERMOPLASTIC HOSES HIGH PRESSURE Type 520N Standard Hydraulic Hose Specifications Exceed SAE 100 R8 2 Construction: Applications: Covering: Reinforcement: Internal: High-pressure hose for use with oil-based and synthetic hydraulic oils, as well as gases. Low volumetric expansion and small outer diameter due to aramid fiber reinforcement. Also available as dual- or multi-hose. Max length change is +/- 2% at working pressure. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Black pin-pricked Polyurethane 1 layer braided synthetic aramid fiber Polyamide Temperature range: ÷40oC to +100oC for synthetic and oil-based hydraulic oils # Part No 520N-03 520N-04 520N-05 520N-06 520N-08 Fitting Series R mm 4.8 6.3 7.9 9.5 12.7 inch 3/16 1/4 5/16 3/8 1/2 dash -03 -04 -05 -06 -08 mm 10.9 13.0 14.5 16.5 20.6 bar 345 345 310 275 240 psi 5000 5000 4500 4000 3500 bar 1380 1380 1240 1100 960 psi 20000 20000 18000 16000 14000 mm 38 51 64 64 102 kg/m 0.07 0.10 0.12 0.12 0.20 55/56 55/56 55/56 55/56 55/56 Type 528N Standard Hydraulic Hose Non-conductive Hose Specifications Exceed SAE 100 R8 Construction: Applications: High-pressure hose for use with oil-based and synthetic hydraulic oils, as well as gases. Low volumetric expansion and small outer diameter due to aramid fiber reinforcement. Not electrically conductive according to SAE J517 (less than 50 µA at 75,000 Volts per foot). Max length change is +/- 2% at working pressure. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Covering: Reinforcement: Internal: Orange Polyurethane 1 layer braided synthetic aramid fiber Polyamide Temperature range: ÷40oC to +100oC for synthetic and oil-based hydraulic oils # Part No 528N-03 528N-04 528N-05 528N-06 528N-08 2 - 10 Fitting Series R mm 4.8 6.3 7.9 9.5 12.7 inch 3/16 1/4 5/16 3/8 1/2 dash -03 -04 -05 -06 -08 mm 10.9 13.0 14.5 16.5 20.6 bar 345 345 310 275 240 psi 5000 5000 4500 4000 3500 Flexible Solutions bar 1380 1380 1240 1100 960 psi 20000 20000 18000 16000 14000 mm 38 51 64 64 102 kg/m 0.07 0.10 0.12 0.12 0.20 55/56 55/56 55/56 55/56 55/56 THERMOPLASTIC HOSES HIGH PRESSURE Type 590 Hybrid High Pressure Hose Specifications Exceed SAE 100 R2 2 Construction: Applications: Covering: Reinforcement: Internal: High-pressure hose for use with oil-, water- and synthetic-based hydraulic oils. Ideal for applications where small bend radius and excellent aging characteristics are important. Max length change is +/- 2% at working pressure. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Black Polyurethane 1 layer aramid and 1 layer steel wire braiding Polyester Elastomer Temperature range: ÷40oC to +121oC for oil-based hydraulic oils ÷40oC to +57oC for synthetic and water-based oils # Part No 590-03 590-04 590-06 590-08 590-10 590-12 590-16 Fitting Series R mm 4.8 6.3 9.5 12.7 15.9 19.1 25.0 inch 3/16 1/4 3/8 1/2 5/8 3/4 1 dash -03 -04 -06 -08 -10 -12 -16 mm 10.9 13.0 16.3 20.1 24.6 27.9 36.1 bar 345 345 275 240 210 175 140 psi 5000 5000 4000 3500 3000 2500 2000 bar 1380 1380 1100 960 840 690 560 psi 20000 20000 16000 14000 12000 10000 8000 mm 38 44 57 83 152 178 203 kg/m 0.15 0.21 0.29 0.37 0.57 0.66 0.88 55/56 55/56 55/56 55/56 56/58 56/58 56/58 Type 575X High Pressure Hose Low Volumetric Expansion Construction: Applications: Covering: Reinforcement: Internal: High-pressure hose for use with oil-based and synthetic hydraulic oils. Especially designed for applications where low volumetric expansion and stable pressure is required. Max length change is +/- 2% at working pressure. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Black special Polyurethane 1 or 2 layers braided synthetic aramid fiber Polyamide Temperature range: ÷40oC to +100oC for synthetic and oil-based hydraulic oils max. 70oC for water or methanol-based fluids # Part No 575X-03 575X-04 575X-06 575X-08 575X-12 575X-16 Fitting Series R mm 4.8 6.3 9.5 12.7 19.0 25.4 inch 3/16 1/4 3/8 1/2 3/4 1 dash -03 -04 -06 -08 -12 -16 mm 10.8 12.8 16.3 20.6 29.2 40.4 bar 345 345 345 345 345 345 psi 5000 5000 5000 5000 5000 5000 www.fluidcontrol.no bar 1380 1380 1380 1380 1380 1380 psi 20000 20000 20000 20000 20000 20000 mm 38 51 76 102 203 254 kg/m 0.07 0.10 0.13 0.20 0.53 0.80 55/56 55/56 55/56 55/56 58H 58H 2 - 11 THERMOPLASTIC HOSES HIGH PRESSURE 2 Type AS10 Standard Hydraulic Hose Specifications Equivalent to SAE 100 R11 Construction: Applications: Covering: Reinforcement: Internal: High-pressure hose for use with oil-based and synthetic hydraulic oils, as well as gases. Max length change is +/- 2% at working pressure. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Also available in other colors. Black Polyurethane 2 layers braided aramid fiber Polyamide Temperature range: ÷40oC to +100oC for continuous use # Part No AS10-03 AS10-04 AS10-05 AS10-06 AS10-08 AS10-10 AS10-16 Fitting Series R mm 5.0 6.0 8.0 10.0 13.0 16.0 25.0 inch 3/16 1/4 5/16 3/8 1/2 5/8 1 dash -03 -04 -05 -06 -08 -10 -16 mm 13.5 14.8 18.3 19.3 22.6 27.9 36.2 bar 690 690 550 520 415 345 345 psi 10000 10000 8000 7500 6000 5000 5000 bar 2760 2760 2200 2070 1650 1380 1380 psi 40000 40000 32000 30000 24000 20000 20000 mm 100 127 152 175 203 279 356 kg/m 0.14 0.15 0.20 0.25 0.35 0.42 0.52 AS10 AS10 AS10 AS10 AS10 AS10 AS10 Type AS13 Standard Hydraulic Hose Specifications Exceed SAE 100 R8 Construction: Applications: Covering: Reinforcement: Internal: High-pressure hose for use with oil-based and synthetic hydraulic oils, as well as gases. Max length change is +/- 2% at working pressure. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Also available with orange non-electrically conductive covering. Black pin-pricked Polyurethane 2 layers braided polyester fiber Hytrel Temperature range: ÷40oC to +95oC for continuous use # Part No AS13-03 AS13-04 AS13-06 AS13-08 AS13-10 AS13-12 AS13-16 mm 5.0 6.0 10.0 13.0 16.0 20.0 25.0 inch 3/16 1/4 3/8 1/2 5/8 3/4 1 dash -03 -04 -06 -08 -10 -12 -16 mm 12.7 15.7 18.7 22.6 25.9 28.7 37.2 bar 340 340 270 240 190 150 140 psi 5000 5000 4000 3500 2750 2250 2000 bar 1370 1370 1100 960 750 620 550 psi 20000 20000 16000 14000 11000 9000 8000 mm 38 50 63 100 150 200 254 For more information on coupling options and quality of materials, please contact us 2 - 12 Fitting Series R Flexible Solutions kg/m 0.13 0.19 0.23 0.31 0.37 0.42 0.61 ASC13 ASC13 ASC13 ASC13 ASC13 ASC13 ASC13 THERMOPLASTIC HOSES HIGH PRESSURE Type HP High-pressure Hose 2 Construction: Applications: High-pressure hose for hydraulic, pneumatic and lubrication oils - such as high-pressure tools, test equipment, offshore pressure control equipment and offshore oil applications. HP8 is not electrically conductive. Covering: Reinforcement: Internal: Polyamide HP=Blue, HPX=Orange, 1 layer braided aramid Polyamide Temperature range: ÷40oC to +100oC, max 70oC for water and methanol-based fluids # Part No HP-3 HP-4 HPX-6 HP8-3 HP8-4 HP8X-6 Fitting Series R mm 5.0 6.0 10.0 5.0 6.0 10.0 inch 3/16 1/4 3/8 3/16 1/4 3/8 dash -03 -04 -06 -03 -04 -06 mm 13.2 15.2 18.8 13.2 15.2 18.8 bar 690 690 690 690 690 690 psi 10000 10000 10000 10000 10000 10000 bar 2760 2760 2210 2760 2760 2210 psi 40000 40000 32000 40000 40000 32000 mm 38 64 76 38 64 76 kg/m 0.13 0.16 0.24 0.13 0.16 0.24 HP HP HP HP HP HP Type 2040N Multi-use Hose Specifications DIN 20 022 Part 1 DNV Approved Construction: Applications: High-pressure hose for hydraulic systems with petroleum, synthetic or water based hydraulic oils. Also ideal for grease, gases and paint spraying. Max length change is +/- 2% at working pressure. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Covering: Reinforcement: Internal: Black Polyurethane 1 layer steel wire braiding Polyamide Temperature range: ÷40oC to +100oC for synthetic- and oil-based hydraulic oils Available in other colors # Part No 2040N-02V00 2040N-03V00 2040N-04V00 2040N-05V00 2040N-06V00 2040N-08V00 2040N-10V00 2040N-12V00 2040N-16V00 Fitting Series R mm 3.2 4.8 6.3 7.9 9.5 12.7 16.0 19.1 25.0 inch 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 1 dash -02 -03 -04 -05 -06 -08 -10 -12 -16 mm 7.0 9.8 11.9 14.0 15.9 19.3 23.5 26.7 33.5 bar 350 340 310 250 240 185 140 125 100 psi 5075 4930 4495 3625 3480 2680 2030 1810 1450 www.fluidcontrol.no bar 1400 1360 1240 1000 960 740 560 500 400 psi 20300 19720 17980 14500 13920 10730 8120 7250 5800 mm 30 30 40 50 60 75 110 170 230 kg/m 0.07 0.11 0.16 0.21 0.24 0.29 0.39 0.50 0.60 PX 56/PX 56/PX 56/PX 56/PX 56/PX PX PX PX 2 - 13 THERMOPLASTIC HOSES HIGH PRESSURE 2 Type 2040H Standard Hydraulic Hose Specifications DIN 20 022 Part 1 DNV Approved Construction: Applications: High-pressure hose for hydraulic systems with synthetic-, water- or petroleum-based hydraulic oils. Good flexibility due to the special construction method. Ideal for lifting equipment, machines and applications requiring high durability. Also available as dual- or multi-hose. Max length change is +/- 2% at working pressure. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Covering: Reinforcement: Internal: Black Polyurethane 1 layer steel wire braiding Polyester Elastomer Temperature range: ÷40oC to +100oC for oil-based hydraulic oils ÷40oC to +57oC for synthetic- and water-based oils # Part No 2040H-03V10 2040H-04V10 2040H-05V10 2040H-06V10 2040H-08V10 2040H-10V10 2040H-12V10 2040H-16V10 Fitting Series R mm 4.8 6.3 7.9 9.5 12.7 16.0 19.1 25.0 inch 3/16 1/4 5/16 3/8 1/2 5/8 3/4 1 dash -03 -04 -05 -06 -08 -10 -12 -16 mm 9.8 11.9 14.0 15.9 19.3 23.5 26.7 33.5 bar 340 310 250 240 185 140 125 100 psi 4930 4495 3625 3480 2680 2030 1810 1450 bar 1360 1240 1000 960 740 560 500 400 psi 19720 17980 14500 13920 10730 8120 7250 5800 mm 30 40 50 60 75 110 170 230 kg/m 0.12 0.17 0.21 0.26 0.31 0.43 0.53 0.72 56/PX 56/PX 56/PX 56/PX 56/PX PX PX PX Type 2370N/H Universal High Pressure Hose Specifications Exceed DIN 20 022 Part 2 TÜV/CGA/AGA Approved for CNG Construction: Applications: Covering: Black Polyurethane Reinforcement: 2 layers steel wire spiral and 2 layers braided synthetic fiber Internal H: Polyester Elastomer Internal N: Polyamide High-pressure hydraulic systems for petroleum- and syntheticbased hydraulic oils and gases and aggressive media. Ideal for hydraulic and rescue tools. For CNG use, the hose is only sold pre-assembled with fittings including kink guards. Also available as dual- or multi-hose. Max length change is +/- 2% at working pressure. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Temperature range: ÷40oC to +100oC for oil-based hydraulic oils (to +120oC for shorter periods) V71 has PA11 inside. For paint spraying, use fittings series NX # Fitting Series R Part No 2370N-04V10 2370N-05V10 2370N-06V10 2370N-08V10 mm 6.3 8.2 9.7 12.8 inch 1/4 5/16 3/8 1/2 dash -04 -05 -06 -08 mm 12.4 14.3 16.4 19.6 bar 465 440 420 350 psi 6740 6380 6090 5075 bar 1860 1760 1680 1400 psi 26970 25520 24360 20300 mm 70 100 120 150 kg/m 0.19 0.25 0.33 0.42 RX RX 9X 9X 2370N-06V71 9.5 3/8 -06 16.4 690 10000 1725 25000 120 0.33 RX 2370H-08V10 12.8 1/2 -08 19.6 350 5075 1400 20300 150 0.42 9X 2 - 14 Flexible Solutions THERMOPLASTIC HOSES HIGH PRESSURE - CHEMJEC Type 2370M (V30) Universal High Pressure Hose Polyflex Hose - ChemJec Specifications Exceed ISO 13628-5 Construction: Applications: Withstands high pressure cycles with no signs of stress cracking. Proven to handle methanol. High collapse resistance (HCR) and also providing longer service life. Extremely low permeability. Medium pressure, high temperature, low volumetric expansion hose. Long length subsea umbilical hose. Excellent chemical resistance. Available in long continous length up to 2,500 m. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Covering: Reinforcement: Internal: Black PA12 High strength wire, synthetic fibre Coextruded core tube with fluoropolymer inside Temperature range: -40°C up to 125°C -40°F up to 257°F # Part No 2370M-06V10 Fitting Series R mm 9.9 inch 3/8 dash -06 mm 16.6 bar 430 psi 6250 bar 1725 psi 25000 mm 70 kg/m 0.33 RX Type 2244N/2245N High-pressure Hose Specifications Exceed SAE 100 R9/R10 Construction: Applications: Covering: Black Polyurethane (Polyurethane from 5/8”) Reinforcement: 2 layers steel wire spiral and 1 layer steel wire braiding Internal: Polyamide High-pressure hydraulic systems for petroleum- and syntheticbased hydraulic oils, spray painting, gases and aggressive media. Ideal for hydraulic and rescue tools. 3/4“ and 1” hoses are DNV type-approved. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Temperature range: ÷40oC to +100oC for oil-based hydraulic oils (to +125oC for shorter periods) # Fitting Series R Part No 2244N-06V00 mm 9.5 inch 3/8 dash -06 mm 18.0 bar 535 psi 7760 bar 2150 psi 31175 mm 120 kg/m 0.50 8X 2244N-08V10 2244N-20V30 2245N-04V00 2245N-05V00 2245N-06V00 2245N-08V00 2245N-10V30 2245N-12V30 2245N-16V30 12.7 32.0 6.3 8.0 9.5 12.7 15.9 19.0 25.4 1/2 1.1/4 1/4 5/16 3/8 1/2 5/8 3/4 1 -08 -20 -04 -05 -06 -08 -10 -12 -16 22.7 44.0 12.5 14.3 17.0 20.7 24.5 28.5 34.0 550 275 450 400 375 350 330 300 275 7970 3990 6530 5800 5440 5080 4780 4350 3990 2200 1100 1800 1600 1500 1400 1320 1200 1100 31900 15950 26100 23200 21750 20300 19140 17400 15950 150 400 70 100 120 165 200 240 280 0.80 1.83 0.25 0.32 0.42 0.52 0.72 0.92 1.15 8X NX NX NX NX NX NX NX NX www.fluidcontrol.no 2 - 15 2 THERMOPLASTIC HOSES HIGH PRESSURE Type 714 Spray Paint Hose 2 Construction: Applications: Type 714 is a special hose for high-pressure spray paint designed to meet the market demands. The steel wire braiding makes the hose 100% electrically conductive. Inner tube specially designed for chlorinated solvents. The polyurethane covering provides excellent flexibility and durability. Also excellent for use as a hydraulic hose. Covering: Reinforcement: Internal: Blue Polyurethane 1 layer steel wire braiding Polyamide Temperature range: ÷40oC to +100oC for synthetic- and oil-based hydraulic oils # Part No 714-03 714-04 714-06 714-08 Fitting Series R mm 4.8 6.3 9.5 12.7 inch 3/16 1/4 3/8 1/2 dash -03 -04 -06 -08 mm 9.4 11.7 15.1 18.3 bar 360 310 225 190 psi 5250 4500 3250 2760 bar 1440 1240 900 760 psi 21000 18000 13000 11000 mm 25 37 50 75 kg/m 0.12 0.16 0.23 0.30 PX PX PX PX Type 715 Spray Paint Hose Construction: Applications: Type 715 is a special hose for high-pressure spray paint designed to meet the market demands. The steel wire braiding makes the hose 100% electrically conductive. Inner tube specially designed for chlorinated solvents. The polyurethane covering provides excellent flexibility and durability. Also excellent for use as a hydraulic hose. Covering: Reinforcement: Internal: Blue Polyurethane 2 layers steel wire braiding Polyamide Temperature range: ÷40oC to +100oC for synthetic- and oil-based hydraulic oils # Part No 715-04 715-06 715-08 2 - 16 Fitting Series R mm 6.3 9.5 12.7 inch 1/4 3/8 1/2 dash -04 -06 -08 mm 13.7 17.0 20.2 bar 480 380 290 psi 7000 5500 4250 Flexible Solutions bar 1920 1520 1160 psi 28000 22000 17000 mm 25 37 62 kg/m 0.30 0.42 0.51 HPX HPX HPX THERMOPLASTIC HOSES ULTRA-HIGH PRESSURE Type 2448N (V91) Umbilical hose 2 Construction: Applications: Covering: Reinforcement: Internal: Available in long lengths for use in subsea umbilicals. Black PA12 4 layers steel wire spiral Methanol washed PA11 Temperature range: ÷40oC to +100oC +70oC for water- or methanol-based fluids # Part No 2448N-04V91 2448N-06V91 Fitting Series R mm 6.0 10.0 inch 1/4 3/8 dash -04 -06 mm 13.8 20.3 bar 1035 1035 psi 15000 15000 bar 4140 4140 psi 60000 60000 mm 150 190 kg/m 0.38 0.74 8X * * For coupling type, please contact us For machines and tools, see group 19 For more information on coupling options and quality of materials, please contact us www.fluidcontrol.no 2 - 17 THERMOPLASTIC HOSES ULTRA-HIGH PRESSURE - CHEMJEC Type 2380N Specifications Exceed SAE R10 Construction: Applications: 2 Covering: Black Polyurethane (other colors on request) Reinforcement: 2 layers steel wire spiral and 2 layers steel wire braid Internal: Polyamide. V91 has methanol-washed PA11 High-pressure hydraulic systems for petroleum- and syntheticbased hydraulic oils. Ideal for hydraulic and rescue tools. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Temperature range: ÷40oC to +100oC for oil-based hydraulic oils, V91 also for methanolbased fluids # Part No 2380N-04V00 2380N-04V91 2380N-05V00 Fitting Series R mm 6.3 6.4 7.9 inch 1/4 1/4 5/16 dash -04 -04 -05 mm 13.3 13.5 15.7 bar 700 690 625 psi 10150 10000 9625 bar 2800 2760 2500 psi 40600 40000 36250 mm 70 70 90 kg/m 0.32 0.27 0.41 8X LX/8X 8X Also available in twin design Type 2380M - Polyflex Hose - ChemJec Specifications Exceed ISO 13628-5 Construction: Applications: Covering: Reinforcement: Internal: Withstands high pressure cycles with no signs of stress cracking. Proven to handle methanol. High collapse resistance (HCR) and also providing longer service life. Extremely low permeability. High pressure, high temperature, low volumetric expansion hose. Long length subsea umbilical hose. Excellent chemical resistance. Available in long continuos length up to 3,000 m. Black PA12 High strength wire Coextruded core tube with fl uoropolymer inside Temperature range: -40°C up to +100°C, short term 125°C # Part No 2380M-04V30 2380M-05V30 Fitting Series R mm 6.4 8.2 inch 1/4 5/16 dash -04 -05 mm 13.4 15.7 bar 690 600 psi 10000 8700 bar 2800 2400 psi 40000 34800 mm 230 90 Also available in twin design kg/m 0.27 0.34 8X/LX * *Consult factory Type 2388N Specifications Exceed SAE R10 Construction: Applications: High-pressure hydraulic systems for petroleum and synthetic based hydraulic oils. Ideal for hydraulic and rescue tools. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Covering: Black Polyurethane (other colors on request) Reinforcement: 2 layers steel wire spiral and 2 layer steel wire braid Internal: Polyamide Temperature range: ÷40oC to +100oC for oil-based hydraulic oils # Part No 2388N-04V00 mm 6.3 inch 1/4 dash -04 mm 13.3 bar 800 psi 11600 bar 3200 psi 46600 mm 80 For more information on coupling options and quality of materials, please contact us 2 - 18 Fitting Series R Flexible Solutions kg/m 0.305 8X THERMOPLASTIC HOSES ULTRA-HIGH PRESSURE Type 2X80N Construction: Applications: Covering: Reinforcement: Internal: High-pressure hydraulic systems for petroleum- and syntheticbased hydraulic oils. Ideal for hydraulic and rescue tools. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Temperature range: ÷40oC to +100oC for oil-based hydraulic oils # Part No 2X80N-04V10 2X80N-06V10 2X80N-12V10 Fitting Series R mm 6.3 9.8 19.8 inch 1/4 3/8 3/4 dash -04 -06 -12 mm 13.4 18.6 30.0 2 Black Polyurethane Steel wire and aramid combination Polyamide bar 700 700 450 psi 10150 10150 6525 bar 2800 2800 1800 psi 40600 40600 26100 mm 38 70 100 kg/m 0.237 0.540 1.080 8X LX LX Type 2390N (V91) Construction: Applications: Covering: Reinforcement: Internal: High-pressure hydraulic systems for petroleum- and syntheticbased hydraulic oils. Ideal for hydraulic and rescue tools. Given pressures are indicative. Maximum working pressure is dependent on temperature and medium. Black Polyurethane Steel wire and aramid combination Polyamide PA11 Temperature range: ÷40oC to +100oC for oil-based hydraulic oils # Part No Fitting Series R 2390N-06V91 2390N-08V91 2390N-12V91 2390N-16V91 mm 9.5 12.7 19.1 25.4 inch 3/8 1/2 3/4 1 dash -06 -08 -12 -16 mm 18.4 21.3 29.0 35.0 bar 445 415 350 280 psi 6454 6019 5076 4061 bar 1780 1660 1400 1120 psi 25800 24100 20300 16200 mm 180 200 300 340 kg/m 0.33 0.54 0.90 1.35 9X 9X 9X 9X 2390N-06V91-10K 9.5 3/8 -06 18.4 712 10320 1780 25800 180 0.33 9X For more information on coupling options and quality of materials, please contact us www.fluidcontrol.no 2 - 19 THERMOPLASTIC HOSES ULTRA-HIGH PRESSURE Type 2440D/2440N Ultra-high-pressure Hose 2 Construction: Applications: Covering: Covering: Reinforcement: Internal: Internal: For use with petroleum or synthetic hydraulic fluids, gases and chemicals. Well suited for hydraulic prestress tools, test rigs and offshore oil applications. The hose is marked with manufacturer, type of hose, working pressure and production date. Also available as pin-prickled - add -P after Part No. Also available in a methanol-washed version - V91. 2440D Blue Polyamide 2440N Black Polyamide 4 layers steel wire spiral 2440D Polyoxymethylene 2440N Polyamide Temperature range ÷40oC to +70oC # Part No 2440D-025V32 2440D-03V32 2440D-04V32 2440D-05V32 2440N-06V30 2440N-08V30 2440N-12V30 2440N-16V30 Fitting Series R mm 3.9 4.7 6.3 8.0 9.7 12.8 19.6 25.0 inch 5/32 3/16 1/4 5/16 3/8 1/2 3/4 1 dash -025 -03 -04 -05 -06 -08 -12 -16 mm 10.4 11.5 12.5 15.1 19.4 22.5 30.0 37.0 bar 2200 1800 1640 1500 1400 1300 1000 900 psi 31900 26090 23770 21740 20290 18840 14490 13040 bar 5500 4400 4100 3750 3500 3250 2500 2250 psi 79750 65220 59420 54350 50720 47100 36230 32610 mm 100 120 155 175 190 200 250 300 kg/m 0.21 0.25 0.33 0.44 0.70 0.94 1.39 1.90 LX LX LX LX LX LX LX LX Type 2640D/2640N Ultra-high-pressure Hose Construction: Applications: For use with petroleum or synthetic hydraulic fluids and chemicals. Well suited for hydraulic prestress tools, test rigs and offshore oil applications. The hose is marked with manufacturer, type of hose, working pressure and production date. Covering: Reinforcement: Internal: Internal: Blue Polyamide 6 layers steel wire spiral 2640D Polyoxymethylene 2640N Polyamide Temperature range: ÷40oC to +70oC # Part No 2640D-025V32 2640D-03V32 2640D-05V32 2640N-08V32 2640N-12V32 mm 4.0 4.8 7.9 12.7 19.0 inch 5/32 3/16 5/16 1/2 3/4 dash -025 -03 -05 -08 -12 mm 12.0 13.0 16.9 24.5 33.0 bar 2800 2500 2100 1800 1400 psi 40600 36230 30430 26090 20290 bar 7000 6250 5250 4500 3500 For water jetting - see page 2-25 2 - 20 Fitting Series R Flexible Solutions psi 101500 90580 76090 65220 50720 mm 140 175 225 290 350 kg/m 0.29 0.41 0.68 1.36 2.10 5X 5X 5X 5X 5X BLACK EAGLE COLORGARD™ POLYFLEX HOSE BLACK EAGLE FAMILY + COLORGARD™ Type 2640N / 2580N Main Features • • • • • COLORGARD, dual colour safety feature with extra thick cover for superior abrasion resistance. Plyamide-11 core tube for cleanliness Weight up to 27.5 kg/m Smaller OD than flexible pipe allows more hose per reel Excellent chemical resistance providing long service life in sea water Applications: Flexible, lightweight, chemical resistant alternative to steel or flexible pipe. Used for high volume pumping in well service applications such as cementing chemical injection and other onshore and subsea well stimulation operations. Available in long continuous lengths (500m to 2,000m depending on size). Construction: Core tube: PA11 Pressure reinforcement: High strength wire Cover: Extra thick polyurethane cover Colour:ColorGardTM Safety feature (red inner, black outer cover) Temperature range: -40oC up to +70oC -40oF up to +158oF # Part No Fitting Series R mm inch dash mm bar psi bar psi mm kg/m 2640N-16V80 26.0 1 -16 40.0 1035* 15000* 3000 43500 400 2.90 HX 2640N-24V80 2580N-32V80** 2640N-48V80 38.1 50.5 76.0 1.1/2 2 3 -24 -32 -48 70.0 84.5 130.0 690* 690* 690* 10000* 10000* 10000* 2277 1725 2330 33000 25000 33750 500 800 1200 7.20 9.40 27.50 5X BL 5X Notes: *Maximum working pressure with safety factor less than 4:1 ** 2580N-32V80 is a replacement for 2640N-32V80 www.fluidcontrol.no 2 - 21 2 GOLDEN EAGLE COLORGARD™ POLYFLEX HOSE GOLDEN EAGLE FAMILY + COLORGARD™ Type 2640M / 2580M / 2448M 2 Main Features • • • • • COLORGARD, dual colour safety feature with extra thick cover for superior abrasion resistance. Fluorpolymer based. Weight up to 9.2 kg/m Smaller OD than flexible pipe allows more hose per reel Excellent chemical resistance providing long service life in sea water GOLDEN EAGL COLORGARD™ Applications: Flexible, lightweight, chemical resistant alternative to steel or flexible pipe. Used for high volume pumping in well service applications with acid fluids and chemical injection and other onshore and subsea well stimulation operations. Available in long continuous lengths (500m to 2,000m depending on size). Construction: Core tube: Fluorpolymer based Pressure reinforcement: High strength wire Cover: Extra thick Polyurethane Colour:ColorGardTM Safety feature (red inner, black outer cover) Temperature range: -40oC up to +100oC, short term 125oC -40oF up to +212oF, short term 257oF # Part No Fitting Series R mm inch dash mm bar psi bar psi mm kg/m 2640M-16V80 26.0 1 -16 40.0 690* 10000* 2300 33350 400 2.90 HX 2640M-24V60** 38.0 1.1/2 -24 62.0 690* 10000* 2300 33350 500 6.40 5X 2640M-24V88 38.0 1.1/2 -24 70.5 690 10000* 2300 33350 500 7.20 5X 2448M-32V80 50.5 2 -32 82.0 345* 5000* 1380 20000 500 7.00 BL 2448M-32V88 51.0 2 -32 80.5 345* 5000* 1380 20000 500 8.50 BL 2580M-32V80 2580M-32V88 50.5 51.0 2 2 -32 -32 84.5 84.5 690* 690* 10000* 10000* 1725 1725 25000 25000 800 800 9.20 9.40 BL BL Notes: *Maximum working pressure with safety factor less than 4:1 ** V60: black PVDF cover 2 - 22 Flexible Solutions LE ™ PHALCON COLORGARD™ POLYFLEX HOSE PHALCON+ COLORGARD™ Type 2440N / 2448N Main Features • • • • • COLORGARD, dual colour safety feature with extra thick cover for superior abrasion resistance. Fluorpolymer- core tube for cleanliness. Weight up to 7 kg/m Smaller OD than flexible pipe allows more hose per reel Excellent chemical resistance providing long service life in sea water Applications: Used for high volume pumping in well service applications such as chemical injection and other onshore and subsea well stimulation operations. Available in long continuous lengths. Construction: Core tube: PA11 Pressure reinforcement: High strength wire Cover: Extra thick Polyurethane cover Colour:ColorGardTM Safety feature (red inner, black outer cover) Temperature range: -40oC up to +70oC -40oF up to +159oF # Part No Fitting Series R mm inch dash mm bar psi bar psi mm kg/m 2440N-16V80 26.0 1 -16 45.0 517 7500 2070 30000 300 3.00 2440N-24V80 38.0 1.1/2 -24 65.0 345 5000 1380 20000 450 4.20 * * 2448N-32V80 50.5 2 -32 80.5 345 5000 1380 20000 500 8.50 BL Notes: *Consult factory www.fluidcontrol.no 2 - 23 2 THERMOPLASTIC HOSES CHEMJEC Type 2240D Ultra-high-pressure Hose For Pipe-cleaning 2 Construction: Applications: Covering: Reinforcement: Internal: Ultra-high-pressure hose for cleaning of pipes, heat exchangers, etc. in the chemical and oil industries. The hose can be used as a flexible lance with pressure over 750 bar. The hose is available as a special hose with stainless steel wicker work for added external protection. The hose is marked with manufacturer, type of hose, working pressure and production date. Blue Polyamide 2 layers steel wire spiral Polyoxymethylene Temperature range: ÷10oC to +70oC for water # Part No 2240D-02V32 2240D-025V32 2240D-03V32 2240D-04V32 2240D-05V32 Fitting Series R mm 3.0 4.0 4.8 6.3 7.9 inch 1/8 5/32 3/16 1/4 5/16 dash -02 -025 -03 -04 -05 mm 7.0 7.7 9.5 11.5 13.3 bar 1100 1200 1000 1000 900 psi 16950 17400 14500 14500 13050 bar 2750 3000 2800 2500 2250 psi 39875 43500 40580 36230 32610 mm 60 75 95 110 120 kg/m 0.07 0.10 0.20 0.26 0.22 TX/AX TX/AX TX/AX TX/AX TX/AX Type 2240M Ultra-high-pressure Hose Polyflex Hose - ChemJec Construction: Applications: Withstands high pressure cycles with no signs of stress cracking. Proven to handle methanol. High collapse resistance (HCR) and also providing longer service life. Extremely low permeability. Meets or exceeds the performance requirements of ISO 13628-5. Medium pressure, high temperature, low volumetric expansion hose. Excellent chemical resistance. Long length subsea umbilical hose. Available in long continous length up to 3,000 m. Covering: Reinforcement: Internal: Black PA12 High strength wire Coextruded core tube with fl uoropolymer inside Temperature range: -40°C up to +100°C, short term 125°C -40°F up to +212°F, short term 257°F # Part No 2240M-04V30 2 - 24 Fitting Series R mm 6.4 inch 1/4 dash -04 mm 11.7 bar 430 psi 6250 Flexible Solutions bar 1725 psi 25000 mm 120 kg/m 0.17 RX THERMOPLASTIC HOSES WATER JETTING HOSES Type 2388N Ultra-high-pressure Hose “Blueline” Water Jetting Hose Construction: Applications: Covering: Blue Polyurethane, RAL 5001 Reinforcement: 2 layers steel wire spiral and 2 open layers steel wire spiral Internal: Polyamide Ultra-high-pressure hose for cleaning-applications. Particularly suitable for use in water jet cleaning in production, shipbuilding, ships, tanks, concrete work, etc. Well suited for removing dirt, rust, paint, cement, asphalt, etc. The hose is marked with manufacturer, type of hose, working pressure and production date. Temperature range: ÷40oC to +70oC for water # Part No 2388N-04V12W 2388N-08V12W Fitting Series R mm 6.3 12.7 inch 1/4 1/2 dash -04 -08 mm 13.3 23.0 bar 1280 1100 psi 18560 15950 bar 3200 2750 psi 46400 39875 mm 80 80 kg/m 0.30 0.80 BS BS Type 2580N Ultra-high-pressure Hose “Blueline” Water Jetting Hose Construction: Applications: Covering: Blue Polyurethane Reinforcement: 4 layers steel wire spiral and 2 open layers steel wire spiral Internal: Polyamide Ultra-high-pressure hose for cleaning-applications. Particularly suitable for use in water jet cleaning in production, shipbuilding, ships, tanks, concrete work, etc. Well suited for removing dirt, rust, paint, cement, asphalt, etc. The hose is marked with manufacturer, type of hose, working pressure and production date. Temperature range: ÷40oC to +70oC for water # Part No 2580N-06V12 2580N-08V12 2580N-12V12 Fitting Series R mm 9.5 12.7 19.0 inch 3/8 1/2 3/4 dash -06 -08 -12 mm 21.6 25.0 32.6 bar 1600 1400 1200 psi 23200 20300 17400 www.fluidcontrol.no bar 4000 3500 3000 psi 58000 50750 43500 mm 95 110 170 kg/m 0.94 1.19 1.76 BL BL BL 2 - 25 2 THERMOPLASTIC HOSES WATER JETTING HOSES - CHEMJEC Type 2440D/2440N Ultra-high-pressure Hose Water Jetting Hose 2 Construction: Applications: Covering: Reinforcement: Internal: Internal: Ultra-high-pressure hose for cleaning-applications. Particularly suitable for use in water jet cleaning in production, shipbuilding, ships, tanks, concrete work, etc. Well suited for removing dirt, rust, paint, cement, asphalt, etc. The hose is marked with manufacturer, type of hose, working pressure and production date. Polyamide, V32=Blue, V30=Black 4 layers steel wire spiral 2440D Polyoxymethylene 2440N Polyamide Temperature range: ÷40oC to +70oC for water # Part No 2440D-025V32 2440D-03V32 2440D-04V32 2440D-05V32 2440N-06V30 2440N-08V30 2440N-12V30 2440N-16V30 Fitting Series R mm 3.9 4.7 6.3 8.0 9.7 12.8 19.6 25.0 inch 5/32 3/16 1/4 5/16 3/8 1/2 3/4 1 dash -025 -03 -04 -05 -06 -08 -12 -16 mm 10.4 11.5 12.5 15.1 19.4 22.5 30.0 37.0 bar 2200 1800 1640 1500 1400 1300 1000 900 psi 31900 26090 23770 21740 20290 18840 14490 13040 bar 5500 4400 4100 3750 3500 3250 2500 2250 psi 79750 65220 59420 54350 50720 47100 36230 32610 mm 100 120 155 175 190 200 250 300 kg/m 0.21 0.25 0.33 0.44 0.70 0.94 1.39 1.90 LX LX LX LX LX LX LX LX Type 2440M Ultra-high-pressure Hose Polyflex Hose - ChemJec Construction: Applications: Covering: Reinforcement: Internal: Withstands high pressure cycles with no signs of stress cracking. Proven to handle methanol. High collapse resistance (HCR) and also providing longer service life. Extremely low permeability. Meets or exceeds the performance requirements of ISO 13628-5. High pressure, high temperature, low volumetric expansion hose. Long length subsea umbilical hose. Excellent chemical resistance. Available in long continuos length up to 3,000 m. Black PA12 High strength wire Coextruded core tube with fl uoropolymer inside Temperature range: -40°C up to +100°C, short term 125°C -40°F up to +212°F, short term 257°F # Part No 2440M-04V30 2440M-05V30 2440M-06V30 2440M-08V30 2440M-12V30 2440M-16V30* mm 6.4 8.1 9.9 12.9 19.8 25.2 inch 1/4 5/16 3/8 1/2 3/4 1 dash -04 -05 -06 -08 -12 -16 mm 13.1 16.0 19.5 22.7 30.2 37.2 bar 865 690 690 690 630 560 psi 12500 10000 10000 10000 9135 8120 *Product under development 2 - 26 Fitting Series R Flexible Solutions bar 3450 2760 2760 2760 2500 2250 psi 50000 40000 40000 40000 36250 32625 mm 150 175 190 200 250 300 kg/m 0.31 0.49 0.73 0.94 1.46 1.90 8X LX LX LX LX LX THERMOPLASTIC HOSES WATER JETTING HOSES Type 2640D/2640N Ultra-high-pressure Hose Water Jetting Hose Construction: Applications: Covering: Reinforcement: Internal: Internal: Ultra-high-pressure hose for cleaning-applications. Particularly suitable for use in water jet cleaning in production, shipbuilding, ships, tanks, concrete work, etc. Well suited for removing dirt, rust, paint, cement, asphalt, etc. The hose is marked with manufacturer, type of hose, working pressure and production date. Blue Polyamide 6 layers steel wire spiral 2640D Polyoxymethylene 2640N Polyamide Temperature range: ÷40oC to +70oC for water # Part No 2640D-025V32 2640D-03V32 2640D-05V32 2640N-08V32 2640N-12V32 2640N-16V32 Fitting Series R mm 4.0 4.8 7.9 12.7 19.0 25.4 inch 5/32 3/16 5/16 1/2 3/4 1 dash -025 -03 -05 -08 -12 -16 mm 12.0 13.0 16.9 24.5 33.0 40.0 bar 2800 2500 2100 1800 1400 1200 psi 40600 36230 30430 26090 20290 17390 www.fluidcontrol.no bar 7000 6250 5250 4500 3500 3000 psi 101500 90580 76090 65220 50720 43480 mm 140 175 225 290 350 400 kg/m 0.29 0.41 0.68 1.36 2.10 2.90 HX/5X HX/5X HX/5X HX/5X HX/5X HX/5X 2 - 27 2 THERMOPLASTIC HOSES WATER JETTING HOSES Type 2740D Ultra-high-pressure Hose Water Jetting Hose 2 Construction: Applications: Covering: Reinforcement: Internal: Ultra-high-pressure hose for cleaning-applications. Particularly suitable for use in water jet cleaning in production, shipbuilding, ships, tanks, concrete work, etc. Well suited for removing dirt, rust, paint, cement, asphalt, etc. The hose is marked with manufacturer, type of hose, working pressure and production date. Red or yellow Polyamide 6 layers steel wire spiral Polyoxymethylene Temperature range: ÷40oC to +70oC for water # Part No 2740D-025V16 2740D-03V34 2740D-05V34 2740D-08V30 Fitting Series R mm 4.0 4.8 7.9 12.7 inch 5/32 3/16 5/16 1/2 dash -025 -03 -05 -08 mm 12.0 13.2 17.2 27.0 bar 3000 2800 2500 2000 psi 43500 40600 36250 29000 bar 7800 7000 6250 5000 psi 113100 101500 90625 72500 mm 120 200 200 300 kg/m 0.40 0.47 0.70 1.85 HX HX HX HX Type 2840D Ultra-high-pressure Hose Water Jetting Hose Construction: Applications: Covering: Reinforcement: Internal: Ultra-high-pressure hose for cleaning-applications. Particularly suitable for use in water jet cleaning in production, shipbuilding, ships, tanks, concrete work, etc. Well suited for removing dirt, rust, paint, cement, asphalt, etc. Can replace the steel pipes where flexibility is required. The hose is marked with manufacturer, type of hose, working pressure and production date. Red Polyamide 8 layers steel wire spiral Polyoxymethylene Temperature range: ÷40oC to +70oC for water # Part No 2840D-03V34 2840D-05V34 2840D-08V30 2 - 28 Fitting Series R mm 4.8 7.9 12.7 inch 3/16 5/16 1/2 dash -03 -05 -08 mm 15.0 19.5 29.8 bar 4000 3000 2500 psi 58000 43500 36250 Flexible Solutions bar 8000 7000 6250 psi 116000 101500 90625 mm 200 250 350 kg/m 0.66 1.10 2.50 WX WX WX CHEMICAL TABLE THERMOPLASTIC HOSES Ratings Code G -Good to excellent. Little or no swelling, tensile or surface changes. Preferred choice. 2 L -Marginal or conditional. Noticeable effects but not necessarily indicating lack of safety. Further testing suggested for specific application. P -Poor or unsatisfactory. Not recommended without extensive and realistic testing. – -Indicates that this was not tested. Material Code for Hose Core Tubes polyflex ® / Parflex® Part Numbers H Polyester elastomer 2040H, 2370H, 515H, 518B, 518C, 550H, 558H, 55LT, 560, 590, 593, 1202LT N Polyamide 2010N, 2020N, 2X20N, 2040N, 2244N, 2245N, 2370N, 2440N, 2380N, 2640N, 520N, 540N, 573X, 573XL, 575X, 580N, 588N, HP, HP8 PV Polyvinylchloride (PVC) GPH NC Nylon co polymer 510A, 515A TFE Polytetrafluorethylene (PTFE) 2030T, 2033T, 919, 929, 939/939B, 919U Polyoxymethylene 2440D, 2640D POM Material Code for Hose Covers Polyurethane 2010N, 2040N, 2040H, 2244N, 2245N, 2370H, 2370N, 2380N, 510, 830, 838, 515A, 515H, 510A, 518B, 540N, 550H, 558H 560, 520N, 580N, 588N, 590, 593, HP, HP8, 919U HF Special elastomer 55LT, 1202LT PV Polyvinylchloride (PVC) GPH Polyester elastomer 2040N Special elastomer 518C Polyamide 2010N, 2020N, 2X20N, 2440D, 2440N, 2640D2245N, 2244N U H PFX N Material Code for Sealing Components V FKM O-rings Notes on the Chemical Resistance Table (1) The fluid resistance tables are simplified rating tabulations based on immersion tests at 24° C. Higher temperatures tend to reduce ratings. Since final selection depends on pressure, fluid and ambient temperature and other factors not known to Parker Hannifin , no performance guarantee is expressed or implied. The indications do not imply any compliance with standards and regulations and do not refer to possible changes of colour, taste or smell. For food and drinking water specially approved materials have to be used. For fluids not listed or for advice on particular applications, please consult Parker Hannifin GmbH, Polyflex Division in Hüttenfeld, Germany. (2) Hose applications for these fluids must take into account legal and insurance regulations. The chemical resistance indicated does not express or imply approval by certain institutions. (3) Satisfactory at some concentrations and temperatures, unsatisfactory at others. (4) For gas applications, the cover should be pin-pricked and the pressure must not be released quickly. Special safety guard accessories are to be used to prevent damage or personal injury in the event of failure. (5) Chemical resistance does not imply low permeation rates. Please consult Parker Hannifin for a recommendation for your specific requirements (6)The indication of chemical resistance does not imply any special food compatibility; it refers only to the chemical resistance of the material. (7)Chemical resistance does not imply acceptability for use in airless paintspray applications. These applications require a special, electrically conductive hose. www.fluidcontrol.no 2 - 29 CHEMICAL TABLE THERMOPLASTIC HOSES 2 2 - 30 Flexible Solutions CHEMICAL TABLE THERMOPLASTIC HOSES 2 www.fluidcontrol.no 2 - 31 CHEMICAL TABLE THERMOPLASTIC HOSES 2 2 - 32 Flexible Solutions CHEMICAL TABLE THERMOPLASTIC HOSES 2 www.fluidcontrol.no 2 - 33 NOTES 2 2 - 34 Flexible Solutions
Similar documents
Right Hand Female for Water Jetting Nozzle Fitting
mm
SCO-2370
Sens-up (Frame Integration)
Gain Control
White Balance
Electronic Shutter Speed
Digital Zoom
Flip / Mirror
Alarm
Communication
Protocol
Environmental
Operating Temperature / Humidity
Ingress Protec...
Radiation Curing: State-of-the-Art Assessment
After a review of the literature on all aspects of radiation-processing technologies, the project team interviewed U.S., European, and Japanese equipment manufacturers, material suppliers, and end ...
