i 40 Indicator i 40-SS i 40-PM i 40-DR

i 40 Indicator
WWW.PRECIAMOLEN.COM
i 40-SS
i 40-DR
User Guide
04-55-00-1 MU A - 12/2012
i 40-PM
This guide is intended for i40 indicator users.
It allows starting the equipment quickly. For electrical
connection and installation, refer to the following manuals:
• Wiring diagram: 04-50-00 DD.
• Installation manual: 04-55-00 MI.
Safety
For devices connected through a power outlet, the
NF EN 60 950 standard requires to have this outlet installed
close to the equipment and easily accessible. For equipment
connected permanently to mains, an easily accessible cut-off
device must be included to the permanent installation.
Contents
Foreword
Document conventions ...................................................................................................
Recommendations .........................................................................................................
2
2
Overview
Keyboard ........................................................................................................................
Navigation principle ........................................................................................................
Screen ............................................................................................................................
Help area – Valid key indication detail ...........................................................................
Basic parameters ...........................................................................................................
3
4
5
6
6
Operator functions
Introduction .....................................................................................................................
Power on ........................................................................................................................
Zeroing ...........................................................................................................................
Taring .............................................................................................................................
Initial zero setting ...........................................................................................................
Gross weight recall .........................................................................................................
Range W2 ......................................................................................................................
Information viewing ........................................................................................................
DSD reading ...................................................................................................................
7
7
8
8
8
9
9
9
11
Operator setting
Introduction .....................................................................................................................
Manually entering a tare value (preset tare) ...................................................................
Threshold configuration ..................................................................................................
Metrological screen ........................................................................................................
12
12
13
14
Operator configuration
Introduction .....................................................................................................................
Threshold configuration ..................................................................................................
Threshold switching ........................................................................................................
Saving ............................................................................................................................
15
15
16
17
Error messages
04-55-00-1 MU A
1
i 40 Indicator
Foreword
$ Document conventions
%
Pictograms
O
P
O
Important warning concerning people safety.
Remark concerning the preservation and proper equipment maintenance.
Note aiming to:
- facilitate reading the manual.
- optimally implement the equipment.
%
Terminology and abbreviations
The menu options or parameters are noted:
• OPERATOR / OPTION 1 / OPTION 2... / PARAMETER
or
• INSTALLER / OPTION 1 / OPTION 2... / PARAMETER
In this manual, the functions are all executed in OPERATOR mode, the notations are
abbreviated as follows:
• OPTION 1 / OPTION 2...
2 / PARAMETER
$ Recommendations
For optimum accuracy and equipment preservation:
• Do not submit the indicator and scale to shocks or overloads.
• Do not store any load on the instrument unload it as soon as weighing is complete.
• Never use solvents or abrasives product for cleaning.
2
04-55-00-1 MU A
Overview
$ Keyboard
Function
E
Escape
Escape a menu or the input without having it taken
into account.
- In operating mode, provides access to
application setting.
- Allows entering configuration mode by
pressing and holding power.
m
Menu
R
Validation
Input in a menu or take into account the current
input.
E+R
Restart
Hold these keys pressed to restart the indicator.
u
< >
d
Z
t
B
04-55-00-1 MU A
Navigation keys
Navigating in the menu or list options.
Indication < > in the help area.
Zeroing
Taring
Gross weight recall
3
i 40 Indicator
$ Navigation principle
• The navigation keys allow moving in menus and lists of predefined values. They
are active when the symbols < > are displayed in zone 3 of the screen (Voir
“Screen”, page 5.):
< >
R
1. Scroll through the options at the same level (or possible
values).
2. Validate the selected option (or the selected value).
• In the same case for the consultation of recorded values:
< >
Scroll through the displayed information.
• In case of navigation error:
E
Exit a menu, an item or option (move up one level).
• Reach the store option (configuration mode):
E
4
Back to the configuration top level menu to reach the
storage option.
Actuate the button repeatedly, if necessary.
04-55-00-1 MU A
$ Screen
5
1
8888.888
d
k
4
888
3
8888888888 W z
i
.
7
2
6
Function
Title / Symbol
1.
Weight area
2.
User area
Indications intended for the user.
NET indication if tare taken into account.
Additional unit.
Indication of valid keys.
See detail below.
Help area.
kg g t lb
Unit.
5.
D
6.
Displaying weight present on the receiver.
-
3.
4.
Operating mode
- No symbol. The displayed weight is a metrological
reference.
- Symbol D displayed. The displayed weight is not a
metrological reference.
W1W2
Range 1 or 2 is active.
i
The weight is unstable.
z
7.
04-55-00-1 MU A
.
The weight is in the zero area and stable.
Confirmation of a key-press
5
i 40 Indicator
$ Help area – Valid key indication detail
<>
Choice of menu, of value.
0-9
Numeric input.
0-Z
Alphanumeric input.
1-6
Numeric entry between two specified values ??(e.g.between 1 and 6).
<>
Indication of a menu (even if there is only one option).
ESC
Output of a screen showing data display only.
$
Validation by R if necessary
$ Basic parameters
%
Language
• PARAMETERS / LANGUAGE
Choose English or French.
%
Display
• PARAMETERS / DISPLAY / ECO MODE allows setting auto-extinction:
ON
OFF
- Turning off the backlight after 30s of inactivity, weight to zero.
- After 1hour of inactivity, weight zero, the indicator turns off.
Not auto-extinction.
• PARAMETERS / DISPLAY / BRIGHTNESS adjusts the backlight intensity:
3 levels or extinction.
• PARAMETERS / DISPLAY / COLOR sets the background colour of the
screen: 7possible colours.
6
04-55-00-1 MU A
Operator functions
$ Introduction
The operator functions are available when the indicator is powered on.
$ Power on
1. The instrument performs a self-test.
Check the proper display operation (no
defective segment).
8888.888
.
.
k
888
0
6
8888888888 W z
i
v 1.0.5
2. The software version is displayed.
0.0
3. The self-test is complete, the instrument
initialises the measurement and it is ready for
use.
T:
04-55-00-1 MU A
md
0 KG
k
z
7
i 40 Indicator
$ Zeroing
When the load receiver is empty and the displayed weight is not zero, the zero function
allows to reset to zero the displayed weight (This function is limited to ± 2% of the maximum
instrument range from the initial zero in trade use or to a configuration value outside legal
metrology).
0.2
1. Receiver empty, the weight displayed is different
from zero.
O1:
50.0KG
0.0
2. Select the reset to zero function (Z).
The displayed weight is set to zero.
O1:
k
50.0KG
k
z
$ Taring
The taring function allows storing the load weight in place on the receiver (container) as
tare value and then obtain the product net weight (displayed weight = total weight - tare).
0.2
1. Place the container on the load receiver.
O1:
50.0KG
0.0
2. Select the taring function (T).
The displayed weight corresponds to the net
weight.
O1:
k
50.0KG
k
z
$ Initial zero setting
This zero setting can be made when the indicator is powered on. To do this, when
powering on, the user presses the key T until the equipment starts.
This zero is used as reference to other zero devices.
8
04-55-00-1 MU A
$ Gross weight recall
0.2
1. The result of a net weighing is displayed.
O1:
50.0KG
0.0
2. Press the key B.
The screen changes colour (cyan) and the result
is displayed as gross weight for a few seconds.
O1:
k
50.0KG
k
z
$ Range W2
In dual range, the measurement range selection is ensured automatically by the
instrument based on the weight on the receiver. It is possible to force the instrument to use the
range W2.
Remark: This function is only available for dual range models.
$ Information viewing
Press the keys < and > to scroll through the various information available.
105.0
1. Weight threshold value 1.
O1:
105.0
2. Weight threshold value 2.
O2:
04-55-00-1 MU A
50.0KG
100.0KG
k
z
k
z
9
i 40 Indicator
105.0
3. Weight threshold value 3.
O3:
105.0
4. Weight threshold value 4.
O4:
300.0KG
105.0
5. Tare value.
T:
1.0KG
0.0
105.0
6. Output status.
When one of the thresholds is exceeded, its
status moves from 0 to 1.
200.0KG
O: 0 0 0 0
k
z
k
z
k
z
k
z
k
O: 1 1 0 0
0.0
k
105.0
k
7. Input status.
I: 0 0
8. Weight in High Resolution.
The last number corresponding to the high
resolution is displayed in red.
10
HR:
105.02
z
z
04-55-00-1 MU A
$ DSD reading
MAX :
0
DSD.
0
1. Switching to metrological mode (M).
2. Press key m and scroll through the various
functions with the navigation keys.
3. Select the function DSD and then validate (R).
DSD REF.
0
0
DSD NUM
0
349
0
RECORD
0
4. Select the function READ DSD and then
validate (R),
READ DSD
or select the function DSD REF. and then
validate (R).
This reference allows identifying a bridge.
5. Select the function DSD NUM and then
validate (R).
6. Enter the record number to be read using the
keys < et > and then validate.
Remark: Enter 0 to display the last recording.
7. Validate once again to view the information
corresponding to the record.
04-55-00-1 MU A
k
k
< >
k
< >
k
< >
k
< >
k
0-9
k
< >
11
i 40 Indicator
Operator setting
$ Introduction
Press key m to access operator setting. Then use the keys < and > to access various
available functions.
$ Manually entering a tare value (preset tare)
This function allows to manually entering a tare value for the net weight display.
2.270
1. Select the preset tare function (PT) and then
validate (R).
k
< >
PT
2.270
2. The actual tare value is displayed.
k
0-9
0 KG
2.270
3. Enter the new tare value by pressing the
navigation keys:
• u and d : Change the selected number
value.
• < and > : Move from one number to another.
0.170
The value is taken as tare value. The weighing
result is now displayed as Net.
T:
12
0-9
KG
0.000
4. Validate this new value (R).
d
k
k
NET
0.170 KG
04-55-00-1 MU A
$ Threshold configuration
0.0
0.0
1. Select threshold 1 and then validate (R).
Set the threshold value and then validate to
move to the next threshold.
THRESHOLD1
O1:
0.0
0.0
2. Select threshold 2 and then validate (R).
Set the threshold value and then validate to
move to the next threshold.
THRESHOLD2
O2:
THRESHOLD3
O3:
THRESHOLD4
O4:
04-55-00-1 MU A
200.0KG
0.0
0.0
4. Select threshold 4 and then validate (R).
Set the threshold value and then validate to
move to the next threshold.
100.0KG
0.0
0.0
3. Select threshold 3 and then validate (R).
Set the threshold value and then validate to
move to the next threshold.
50.0KG
300.0KG
k
< >
z
k
z
k
< >
z
k
z
k
< >
z
k
z
k
< >
z
k
z
13
i 40 Indicator
$ Metrological screen
0.0
1. Select the metrology label and then validate
(R).
MET. INFO
2. Press key > to view the metrological data.
The corresponding information is:
• MAX: Equipment maximum range (A).
• MIN: Equipment minimum range (A).
• e: Step (C).
MAX
A
MIN
B
e
C
14
:
0.0
0.0
0.0
0.0
0.0
0.0
300.0kg
:
20e
:
0.1kg
k
< >
z
k
z
k
z
k
z
k
z
k
z
k
z
04-55-00-1 MU A
Operator configuration
$ Introduction
Press key m at indicator power on or restart to access the operator configuration.
$ Threshold configuration
1. Select the function THRESHOLD N in the configuration menu.
(LOGIN / OPERATEUR / APP / THRESHOLD N).
2. Enter the parameter ACTIVE.
This parameter allows enabling the threshold:
• YES ⇒ threshold enabled.
• NO ⇒ threshold disabled.
3. Enter the parameter WEIGHT.
This parameter allows selecting the threshold switching mode:
• NET ⇒ the action is carried out on NET weight.
• GROSS⇒ the action is carried out on GROSS weight.
4. Enter the parameter TRIGGER.
This parameter allows selecting the output switching time:
• >= THRESHOLD⇒ output enabled if the weight is greater than or equal to the
threshold, otherwise disabled.
• <= THRESHOLD ⇒ output enabled if the weight is less than or equal to the
threshold, otherwise disabled.
04-55-00-1 MU A
15
i 40 Indicator
$ Threshold switching
Threshold enabled at
"1" state
Weight
Weight curve
Threshold State
Threshold enabled at
"0" state
Weight
Weight curve
Threshold State
16
04-55-00-1 MU A
$ Saving
When configuration parameters have been changed, the storing can be done in two
ways:
- going back to the highest level in the configuration menu:
menu
< >
SAVE
The SAVE option screen is displayed for about 1s
and then the choice for validating the modified parameters
or not is offered.
NO
save
< >
YES
Select NO to return to the
configuration menu without storing the
changed parameters.
save
< >
Select YES to return to the
configuration menu after storing the
changed parameters.
- by Pressing the keys E + R at the same time.
Similarly, the SAVE option screen is displayed for about 1s, then the choice
whether or not to confirm the modified parameters is proposed.
NO
save
< >
Select NO to turn the indicator off
without storing the modified parameters.
04-55-00-1 MU A
YES
save
< >
Select YES to turn the indicator off
after storing the modified parameters.
17
i 40 Indicator
Error messages
1. Instrument under-load.
• Check the load receiver.
• Carry out a reset to zero.
2. Instrument overload.
• Remove part of the load.
_______
+++++++
d
E23
d
E23
3. Command denied
• Example: Taring with an unstable weight
4. Zero rejected
The allowable weight limit for this function is
exceeded.
• Remove the load and press the zero key.
18
975
975
k
E26
i
k
E40
04-55-00-1 MU A
Notes
04-55-00-1 MU A
19
i 40 Indicator
Notes
20
04-55-00-1 MU A
WWW.PRECIAMOLEN.COM
WWW.PRECIAMOLEN.COM
Head Office & Plant PRECIA-MOLEN
BP 106 - 07000 Privas - France
Tel.
33 (0) 475 664 600
Fax
33 (0) 475 664 330
E-MAIL
[email protected]
www.preciamolen.com
RCS: 386 620 165 RCS Aubenas