Instructions

Instructions
Safety Warnings & Advice
Thank you for purchasing EZ Bed from JML. Please ensure you read these instructions in full
before using your new bed and keep them safe for future reference.
• NEVER unfold or inflate EZ Bed in temperatures below freezing and avoid extensive
exposure to the sun.
• Protect from contact with sharp objects and rough ground.
• Make sure to handle the pump with care.
• DANGER- To reduce the risk of electric shock. Always unplug this appliance from the
electrical outlet before cleaning.
• Keep out of the reach of children at all times.
• This bed is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or a lack of experience and knowledge, unless they have
been given supervision or instruction concerning use by a person responsible for their
safety. Children should be supervised to ensure that they do not play with EZ Bed.
• Use this appliance only for its intended use as described in this manual. DO NOT use
attachments unless recommended for use with EZ Bed.
• NEVER operate EZ Bed if it has a damaged cord or plug. If it is not working properly, has
been dropped and damaged, or dropped into water, seek advice from customer services
regarding its repair.
• Keep the power cord away from heated surfaces.
• NEVER inflate or use EZ Bed with the air openings blocked. Keep the air openings free of
dust, lint, hair and other obstructions.
• NEVER drop or insert any object into any opening.
• DO NOT use outdoors. For indoor household use only.
• DO NOT operate where aerosol (spray) products are being used or where oxygen is being
administered. Keep the pump away from flammable liquids. The area where the pump is
used should be well ventilated.
• To disconnect, turn all controls to the off position then remove the plug from the outlet.
• Power supply for pump must be 230V AC.
• DO NOT leave plugged in when unattended.
• DO NOT obstruct the ventilation hole on the pump.
• DO NOT open the pump case - electrical hazard may result.
• DO NOT over-inflate.
• For proper pump usage: it is recommended not to exceed five minutes of continuous
inflation/deflation time. Pump does not turn off automatically.
• IMPORTANT: Your pump has been designed with a safety feature to avoid overheating. If
your pump stops working during use, please allow 30 minutes before using again.
• In case the pump overheats due to excessive continuous inflation/deflation, the power
will automatically cut-off. The pump cool-down indicator will be on, and will reset to begin
working within 30 minutes. The pump cool-down indicator will be off.
• The pump included in this airbed is thermally protected.
2
Safety Warnings & Advice
• We advise regular inspection of the EZ bed and that any maintenance required is carried
out before use.
• This is an electrical product. To avoid risk of fire, burns, injury, and shock, it should not be
played on or placed near where small children can reach it. DO NOT use in or around
water.
• KEEP AWAY FROM FIRE AND OTHER HEAT SOURCES.
• Make sure there are no sharp objects, steps, drops, or breakable objects where you intend
to lay out EZ Bed before use.
• Unplug when not in use.
SAVE THESE INSTRUCTIONS. This appliance is double insulated. In a double-insulated
product, two systems of insulation are provided instead of grounding. No grounding means
is provided on a double-insulated product, nor is a means for grounding to be added to the
product.
Servicing a double-insulated product requires extreme care and knowledge of the system,
and is to be done only by factory-qualified service personnel. Replacement parts for a
double-insulated product must be identical to the parts they replace.
NOTE:
• Airbed material may stretch during first use and may need additional air to reach desired
firmness.
• Air inside of EZ Bed may expand and contract with varying temperatures, potentially
leading to reduced pressure inside of the bed. If this occurs, simply add more air using the
built-in pump to achieve desired firmness.
PUNCTURE REPAIR (Repair kit included):
1.First, deflate the bed by following the instructions for deflation. Clean and repair the
affected area thoroughly.
2.Cut a piece of clear patch material (included in the repair kit) into a size that will cover the
puncture.
3.Apply the self-adhesive patch over the affected area by peeling off the backing and placing
sticky side down on the bed. Rub patch to ensure adhesion. Allow four hours for repair to
set before attempting to inflate the airbed.
3
Using your EZ Bed
Air bed
Cord
storage
pocket
Pump cool
down indicator
Air inlet
Inflate/deflate
switch
Storage case panel
Bed frame
Instructions for EZ Bed set-up
WARNING: Make sure to fully unzip the
storage case before inflating so the panel
of the storage case is laid flatly off the
floor. This will prevent damage to the bed
frame and ensure smooth extension of its
storage case.
WARNING: When the zipper on the storgae
case is not fully unzipped, the panel of the
storage case is raised off the floor and will
obstruct frame from opening freely. This may
case damage to the bed frame.
4
Using your EZ Bed
1.
2.
3.
Unzip the storage case completely before
inflation. Make sure the panel of the storage
case is laid flatly on the floor, this will prevent
damage to the bed frame and ensure the
smooth extension out of its storage case.
•DO NOT set anything on top or around
EZ Bed during inflation.
•EZ Bed will expand to approximately 9ft in
length and 7ft in width. Clear space
accordingly.
•Plug pump into a polarised 230V AC
outlet.
•Turn switch to Inflate position, EZ Bed will
begin to inflate.
•The frame will automatically extend from
its storage case.
•Pump does not turn off automatically. DO
NOT leave on for more than five minutes.
• When EZ Bed reaches desired
firmness, turn switch to the Off position.
4.
•Unplug and store the cord in the cord
storage pocket.
5.
• EZ Bed is ready for use.
5
Using your EZ Bed
Instructions for EZ Bed storage
1.
•Clear area, bedding and any other
items on top or around EZ Bed prior to
deflation.
•Plug pump into a polarised 230V AC outlet
•Turn switch to the Deflate position.
•The pump will remove the air in your
EZ Bed.
2.
•Pump does not turn off automatically.
•When deflation is completed, turn switch
to the Off position then unplug from the
power outlet and store cord in the cord
storage pocket.
3.
Gently lift up the EZ Bed frame by the end
opposite the pump and push it back into its
storage case.
IMPORTANT: Please ensure that the
mattress is completely deflated prior to
folding up to avoid any risk of puncturing.
6
4.
Zip-up storage case for storage.
5.
Handle and wheels are located on the
storage case for easy and convenient
transport.
Technical Information
Technical Information
Model number
109T / 109F / 109Q
Weight limit
QUEEN SIZE BED
450lbs
204kg
Pump
EZ111-01
DOUBLE SIZE BED
400lbs
181kg
Power
SINGLE SIZE BED
300lbs
136kg
220 - 240 ˜ 50/60Hz
072A, 154W
0.54 PSI MAX
Guarantee
This product is unconditionally guaranteed for one year against all defects of workmanship
and materials. This guarantee does not affect your statutory rights. If you have any problems
or queries about this product please contact JML.
JML Customer Helpline: 0800 781 7831
Disposal and the environment
This product is covered by the waste electrical and electronic equipment (WEEE)
regulations. It should not be discarded with normal household waste, but taken
to your local collection centre for recycling. For further information, please contact
the local authority or approved disposal agency.
This product may be covered under one or more of the following U.S. and / or foreign patents: U.S. Pat.
Nos. : 2,425,162; 2,610,119; 5,827,052; 6,004,116; 6,120,264; 6,332,760 B1; 6,457,192; 6,581,223; 6,679,686
B2; 6,722,306 B1; 6,754,925 B1; 6,754,926 B2; 6,763,540; 6,793,469; 6,990,700 B2; 7,020,921 B2; 7,040,347 B2;
7,114,207; 7,120,955; 7,152,265; 7,246,394; 7,306,694; 7,313,837; 7,334,274; 7,346,950 B2; 7,365,277; 7,475,443;
7,597,123; 7,647,662; 7,739,760; 7,703,160; 7,739,763; 7,922,461 B2; 8,024,830 B2; 8,151,390; 8,214,953; RE42,
559 E; GB2378987; GB2396670; CN 221,800; ZL01129383 Others U.S. and International Patents Pending.
7
JML
JML House, Regis Road, London NW5 3EG
Tel: 020 7691 3800, Fax: 020 7691 3801
E-mail: [email protected]
05/13
Web: www.jmldirect.com