chipper/shredders

Transcription

chipper/shredders - Dorian Drake International Inc.

TABLE OF CONTENTS
PRODUCT INFORMATION
Horsepower Conversion Chart..............................3
Who Uses What.................................................4
Frequently Asked Questions.............................5-8
Product Noise Levels.........................................9
Rotor Specs....................................................10
CHIPPER/SHREDDERS
5cm – Model SC2170......................................11
8cm – Models SC3206 & SC3265
SC3305 & SC3342.......................12-13
CHIPPER/SHREDDER BLOWER
13cm – Model SC5720B..................................14
STUMP GRINDER
Model SG340..................................................15
CHIPPERS
10cm – Model CH4400...................................16
10cm – Model CH5653...................................17
15cm – Models CH611DH & CH6730H.......18-19
20cm – Turntable Models CH8720iH &
CH8993H.................................20-21
23cm – Models CH911DH & CH922DH.......22-23
PTO MACHINES
11cm – Model CH45540.................................24
13cm – Models CH5540H & CH5540...............25
13cm – Model – SC5540B
Chipper/Shredder/Blower.................26
20cm – Model – CH8540.................................27
23cm – Models – CH9540H & CHF9540H..28-29
SKID STEER CHIPPERS
11cm – Models CH450H..................................30
WHEELED VACUUMS
Models – WV190, WV190S...............................31
DEBRIS LOADERS
Models – DL8390 & DL10570.........................32
Models – DL12653 & DL12720.......................33
WARRANTY / PRODUCT CHARTS
Warranty Coverage – Current Models.............36-37
Warranty Coverage – Non-Current Models......38-39
Belts Reference Guide.....................................40
Rotor, Shredder/Chipper Replacement Kits.........41
Blade Kits Chart.........................................42-43
ACCESSORIES
Photos and Part Numbers............................44-50
2
www.bearcatproducts.com
CONVERSION CHART
Horsepower to cc Conversion Chart
GASOLINE ENGINES
cc
Gross
HP
kW
Model Number
Horizontal
170
5.7
4.3
SC2170
Briggs & Stratton
Vertical-Intek
190
6**
4.8
WV190 & WV190S
Briggs & Stratton
Horizontal
205
5.5**
4.1
SC3206
Subaru
Horizontal
265
9
6.7
SC3265
Briggs & Stratton
Horizontal
305
8**
6.0
SC3305
Honda
Vertical-GXV
340
8.9
6.6
SG340
Briggs & Stratton
Horizontal-Intek
342
11**
8.3
SC3342
Honda
Horizontal-GX
390
11.7
8.7
DL8390
Subaru
Horizontal
404
14
10.4
CH4400
Briggs & Stratton
Horizontal Vanguard
570
18
13.4
DL10570
Subaru
Horizontal/Elec.
653
22
16.4
CH5653,DL12653
Subaru
Horizontal/Elec.
720
25
18.6
DL12720,SC5720B
Subaru
Horizontal/Elec./Fuel
Injected
720
28
20.9
CH8720iH
Kohler
Horizontal/Elec.
730
25
18.6
CH6730H
Briggs & Stratton
Horizontal/Elec.-Vanguard
993
35
26.1
CH8993H
Engine Manufacturer
Engine Type
Subaru
DIESEL ENGINES
Engine Manufacturer
Engine Type
Liters
Gross
HP
kW
Model Number
Kubota
1105/Mech.
1.1
25
18.5
CH611DH
Kubota
1105/Mech.
1.1
25
18.5
CH911DH
Kubota
2203/Mech.
2.2
48
35.9
CH922DH
*A non-current ECHO Bear Cat model number **Horsepower rating based on Engine Manufacturer at time of manufacture
011 + 1 + 701.282.5520
3
WHO USES WHAT
ECHO Bear Cat has a wide-range of products to get the job done!
Industry
Product
Used for
Industry
Tobacco stalks
Ag - Specialty
Cemetery
Chipper/Shredder
Animal bedding
Job site clean up
Chipper/Shredder
Job site clean up
Create mulch
Wheeled Vacuum
Leaf removal
Debris Loader
Leaf clean up
Chipper/Shredder
Brush and tree
pruning
Wheeled Trimmer
Aesthetics
Wheeled Vacuum
Leaf removal
Chipper
Shelter belt
clean out
Wheeled Trimmer
Fence line
clean up
Debris Loader
Disposal of broken
branches and
fallen trees
Chipper/Shredder
Dead plant
recycling/moisture
control
Wheeled Trimmer
Tree plots
Chipper/Shredder
Trail maintenance
Chipper
Property
maintenance
clean up
Chipper/Shredder
Golf Course
Wheeled Trimmer
Chipper/Shredder
Brush/hedge clean
up
Wheeled Trimmer
Fence clean up
Wheeled Vacuum
Parking lots and
stadium clean up
Wheeled Trimmer
Wheeled Vacuum
Municipalities
Nurseries
Heavy grass and
weed cleaning for
ponds and creeks
Grass clipping tidy
Chipper/Shredder
Storm damage
Chipper
Create mulch for
landscaping
Wheeled Vacuum
Debris Loader
4
Chipper
Stable clean up
Chipper
Home Owner
with Acreage
Used for
Wheeled Vacuum
Farming
Grounds and
Maintenance
Landscaper
Product
Collecting grass
clippings and leaf
removal
Wheeled Trimmer
Overpass, road
side maintenance
Wheeled Vacuum
City park clean up
Parks and Rec
Wheeled Trimmer
Rental
Yard maintenance
Riding trails
Leaf removal
Street clean up
Leaf pick up
Trail maintenance
Fence lines
Wheeled Vacuum
Parking lot
clean up
Chipper/Shredder
Compost/home
owner clean up
Wheeled Vacuum
Leaf removal
Stump Grinder
Stump removal
Refuse reduction
Pruning
Fence line
Palm frawn
disposal
Tree Service
Chipper
Air quality
protection
Power line clearing
Easements
clearing
FAQ
CHIPPER/SHREDDERS
MODELS: SC2170, SC3206, SC3265, SC3305, SC3342, SC5540B* & SC5720B**
What are these machines designed for?
The ECHO Bear Cat chipper/shredders are designed to effectively reduce the volume of wood, leaves and other organic
material.
When should I chip?
If you don’t plan on composting the material, the material is green and stringy, or larger than 2cm (.75") in diameter.
When should I shred?
If you plan on composting or if the material is smaller than 2cm (.75"), use the shredder. Shredding is also an efficient way
to reduce the volume of leaves or trimmings.
How long will the chipper blades last?
Depending on the type of wood, age and cleanliness, chipper blades will work well for between 5-15 hours.
Dry, dirty wood will dull the blades faster. Alternate dry and wet material to extend blade life.
What is the maximum size of material will these machines chip or shred?
ECHO Bear Cat 5cm (2") chipper/shredders will chip up to 5cm (2") and shred up to 2cm (.75") diameter material.
Do not attempt to put material larger than 2cm (.75") in diameter into the shredder hopper. Doing so may
cause machine failure and will void the warranty.
*PTO Machines
**Electric start models do not include battery.
STUMP GRINDER
MODEL: SG340
What is the application of the Stump Grinder?
The ECHO Bear Cat Stump Grinder is designed with a compact 58.4cm (23") wheel base, enabling it to be used on stumps found in
places large stump grinders cannot get to.
How do I engage the Stump Grinder?
Position the stump grinder so the cutter head is adjacent to the stump. Start the stump grinder and hold up the bottom bail so
it doesn't shut off. Pull the top bail to the handle and hold it there to activate the left wheel brake, holding it so it does not turn.
Gradually, using the locked left tire as a pivot point, slowly pivot the cutter head until the cutting teeth contact the stump. Pivot
the stump grinder on the left wheel in a slow, smooth sweeping motion from left to right as the teeth grind the stump. Do not force
the cutting teeth. Check position by watching through the screen opening. Grind the stump down to a maximum of 10cm (4") below
ground level.
How difficult is it to perform maintenance on the machine?
ECHO Bear Cat products are designed with ease of maintenance in mind. Proper maintenance is vital and should be performed
routinely with blades, belts and bearings being most important.
011 + 1 + 701.282.5520
5
FAQ
CHIPPERS
MODELS: CH4400, CH45540, CH5653, CH5540, CH5540H, CH611DH, CH6730H, CH8540, CH8993H,
CH8720iH, CH9540H, CHF9540H, CH911DH & CH922DH
What are these machines designed for?
The ECHO Bear Cat chipper is designed to effectively reduce the volume of wood, branches, and other organic material.
The typical application for this product group is anywhere from light commercial to municipalities and/or rental.
What types of chippers are available?
ECHO Bear Cat makes chippers with gravity or hydraulic feed, powered by an engine package or a tractor PTO. A hydraulic feed machine
has a hydraulic driven feed roller to efficiently feed branches to the chipper rotor.
When should I buy a gravity feed machine?
If you have an infrequent need for a chipper and time is not a factor, a gravity feed machine will fit your needs.
When should I buy a hydraulic feed machine?
If time or efficiency is an issue, a hydraulic feed chipper allows you to be more productive.
What does it mean when you say hydraulic feed chippers feature an "Auto Feed" system?
"Auto Feed" refers to the way the system senses if the rotor has slowed down too much for maximum chipping performance. When this
happens, the feed roller stops feeding the material, allowing the engine and rotor RPM to recover. Once the engine and rotor RPM have
recovered sufficiently, the feed roller reengages and begins feeding material again. It has also been referred to as the "try again" feature.
Depending on the type of wood, age and cleanliness, chipper blades will work well for between 5-15 hours. Dry, dirty wood will dull the
blades faster. Alternate dry and wet material to extend blade life. Hydraulic feed chippers will have longer blade life.
Will electric start chippers include the starting battery?
No. ECHO Bear Cat products are not shipped with a battery and will need to be purchased separately.
POWER TAKE OFF (PTO) MACHINES
MODELS: CH45540, CH5540, CH5540H, SC5540B, CH8540, CH9540H & CHF9540H
When do I buy a chipper powered by a tractor Power Take Off (PTO) vs. an engine-driven unit?
If you own a tractor a PTO chipper is a smart economic choice.
What are the tractor requirements for these chippers and chipper/shredders?
The ECHO Bear Cat 11cm (4.5") chipper requires a tractor with PTO hp ranging from 11kW-21kW (15hp to 28hp). The ECHO Bear Cat
13cm (5") chippers and chipper/shredders require a tractor with PTO hp ranging from 19kW-34kW (25hp to 45hp). The ECHO Bear Cat
20cm (8") and 23cm (9") chippers require a tractor with PTO hp ranging from 26kW-45kW (35hp to 60hp).
Will the chipper fit my tractor?
The ECHO Bear Cat chippers and chipper/shredders are designed to fit all Category 1 three-point hitches. Chipper weight and tractor hp
needs to be taken into consideration. All Chipper models fit a Category 1 Quick Hitch.
6
FAQ
DEBRIS LOADERS
MODELS: DL8390, DL10570, DL12653 & DL12720
What is the application for the Debris Loader?
The Debris Loader is used for commercial or municipal pickup of leaves, grass, or other light debris.
How much reduction of debris will I get?
There is very limited reduction of the material due to the design for compaction vs. reduction. The Debris Loader is designed to effectively
load leaves, grass, or other light debris from the ground to a vehicle collection bin.
Is there a rental application for this machine?
Yes. Commercial landscapers and municipalities will have a seasonal need for this piece of equipment.
Will electric start Debris Loaders include the starting battery?
No. ECHO Bear Cat products are not shipped with a battery and will need to be purchased separately.
WHEELED VACUUMS
MODELS: WV190 & WV190S
Where can I use the Wheeled Vacuum?
The Wheeled Vacuum is designed to be used for residential, commercial or municipal pickup of leaves, grass or other light debris.
How much reduction of debris will I get?
There is not much reduction; however, by passing through a six-bladed fan into the bag some natural breakage occurs allowing the
five-bushel bag to be filled. Reduction through compaction will happen.
Is it hard to push the Wheeled Vacuum on turf?
The large wheels have ball bearing hubs that allow easy movement.
How many speeds do the Self-Propelled Wheeled Vacuums have and how fast does it go?
There are three separate gears on the transmission of the Self-Propelled Wheeled Vacuum, and the speed range is 1.6-4.8 km/h (1 to 3
mph).
How many height adjustments does the Wheeled Vacuum have?
The Wheeled Vacuum can be adjusted into four different nozzle settings ranging from .64cm-11.4cm (.25" - 4.5") to accommodate all types
of terrain.
What do I use the optional 10.2cm (4") Vacuum Hose Kit for?
This hose kit is designed to allow vacuuming hard to reach places.
011 + 1 + 701.282.5520
7
FAQ
SKID STEER CHIPPERS
MODELS: CH450H, CH500H & CH800H
What is this machine designed for?
The ECHO Bear Cat chipper is designed to effectively reduce wood, brush, and other organic material while using your skid steer as the
power unit.
What is the capacity and hydraulic flow requirements of these machines?
The CH450H has a maximum capacity of 11cm (4.5") and requires at least 41.6 to 56.8 LPM (11 to 15 GPM) on a mini skid steer.
The CH500H has a maximum capacity of 13cm (5") and requires at least 56.7 to 83.3 LPM (15 to 22 GPM) on a low-flow skid steer.
The CH800H has a maximum capacity of 20cm (8") and requires at least 94.6 to 43.8 LPM (25 to 38 GPM) on a hi-flow skid steer.
Will the chipper fit my skid steer?
The ECHO Bear Cat CH500H and CH800H skid steer chippers are equipped with universal attachment ends, capable of hooking up to most
skid steers. The CH450H is designed to mount to mini skid steers.
Depending on the type of wood, age and cleanliness, chipper blades will work well for between 5-15 hours. Dry, dirty wood will dull the
blades faster. Alternate dry and wet material to extend blade life. Hydraulic feed chippers will have longer blade life.
I have a chipper that requires the belt to be engaged. How do I engage
and disengage the belt without it squealing and causing damage to the
belt or other drive components?
ENGAGING THE BELT:
1. AFTER engine is warmed and ready for use, move the throttle control back down to approximately 25% of full throttle.
2. When engine is running at approximately 25% of full throttle, SLOWLY engage belt by using the belt engagement .
DO NOT engage the belt with engine running at high RPM. Engaging belt while engine is running at high RPM WILL result in
significant belt squealing and possible damage.
Engaging belt while engine is running at high RPM may also damage vital drive components of the chipper or chipper/shredder,
3. If the chipper engine stalls while engaging the belt, return the belt engagement back to the START position, restart engine,
SLIGHTLY increase throttle and attempt engagement again.
4. Once the belt is engaged, SLOWLY increase throttle to 100% or full throttle.
5. ALWAYS run the machine at 100% or full throttle when chipping or shredding material.
ENGINE SHUTDOWN/BELT DISENGAGEMENT:
1. WITH THE BELT STILL ENGAGED, SLOWLY move the throttle to the SLOW position.
2. Allow the engine to run at slow idle for 30-60 seconds. This will slow the rotor down to the same RPM as the engine.
3. Stop the engine by moving the throttle to the STOP position or turning off the ignition switch.
4. Allow rotor to come to a complete stop.
5. Once the engine is off and the rotor has completely stopped, the belt can be disengaged by moving the belt engagement back to
the START position.
NEVER disengage the belt as part of the stopping or shut down process. The belt should remain engaged during the entire shutdown process.
Leaving the belt engaged is a vital part of proper shutdown and ensures the rotor stops spinning in conjunction with the engine
shutting off.
8
PRODUCT NOISE LEVELS
Model
Description
CHIPPER/SHREDDERS
dB (pressure)
dB level
SC2170
4cm Capacity – 170cc Subaru SP
97
111
SC3206
8cm Capacity – 205cc Briggs & Stratton OHV
97
111
SC3265
8cm Capacity – 265cc Subaru EX
97
111
SC3305
98
112
SC3342
94
114
SC5720B
13cm Capacity Chipper/Shredder/Blower 720cc Subaru (Towable)
106
120
SG340
Stump Grinder, 340cc Honda
73
87
CH4400
11cm 404cc Subaru EX
87
107
CH5653
13cm Capacity – 653cc Subaru EH
92
109
CH611DH
15cm Capacity – 1.1 Liter Kubota Diesel with Hydralic Feed
94
111
CH6730H
15cm Capacity – 730cc Kohler Command Pro with Hydraulic feed
94
117
CH8720iH
20cm Capacity – 720cc Subaru – turntable with Hydraulic Feed
96
114
CH8993H
20cm Capacity – 993cc Briggs & Stratton Vanguard – Turntable with Hydraulic Feed
96
114
CH911DH
23cm Capacity – 1.1 Liter Diesel with Hydraulic Feed
95
112
CH922DH
23cm Capacity – 2.2 Liter Kubota with Hydraulic Feed
95
112
CHIPPER/SHREDDER/BLOWER
STUMPGRINDER
CHIPPERS
PTO CHIPPERS AND CHIPPER/SHREDDERS
CH45540
11cm Capacity – 540 PTO – 11-21kW (15-28 hp) Input Range
87*
107
CH5540
86*
103
CH5540H
13cm Capacity – 540 PTO with Hydraulic Feed – 19-34kW (25-45 hp) Input Range
86*
103
SC5540B
13cm Capacity – Chipper/Shredder – PTO - 19-34kW (25-45 hp) Input Range
99*
113
CH8540
95*
112
CH9540H
23cm Capacity – 540 PTO rpm with Hydraulic Feed - 26-45kW (35-60 hp) Input Range
95*
112
CHF9540H
23cm Capacity – 540 PTO with Hydraulic Feed - 26-45kW (35-60 hp) hp Input Range
95*
112
WHEELED VACUUMS
WV190
190cc Briggs & Stratton OHV
84
98
WV190S
190cc Briggs & Stratton OHV - Self-Propelled
84
98
DL8390
390cc Honda GX – 20.3cm Intake
116
134
DL10570
570cc Briggs & Stratton Vanguard – 25.4cm Intake
120
138
DL12653
653cc Subaru EH – 30.5cm Intake
97
120
DL12720
720cc Subaru EH – 30.5cm Intake
99
122
DEBRIS LOADERS
*based off towable model
011 + 1 + 701.282.5520
These values were obtained using harmonized EN ISO 3744:2010
9
CHIPPERS
COMMON ROTOR SPECS
35.6cm (14") rotor weighing 22.2kg (49 lbs.) fully assembled
•
•
•
•
•
•
•
2.5cm (1") thick machine balanced cantilever rotor
Models: CH4400, CH45540 & CH450H
Standard 11.4cm x 22.9cm (4.5" x 9") discharge chute. Optional discharge chute is 11.4cm (4.5") square
33cm x 36.8cm (13" x 14.5") feed chute
Two reversible heat-treated steel chipper blades
Four-sided cutter bar/anvil
Chipper Blade Kit: P/N: 76295-00
•
•
•
•
•
•
•
•
3.2cm (1.25") thick machine balanced
10cm (4") and 13cm (5") chippers, Models CH5540, CH5540H & CH5653 – same chipper body
15cm (6") discharge chute rotating 360 degrees
14cm x 17.8cm (5.5" x 7") feed opening
Reversible heat-treated steel chipper blades.
Four-sided adjustable steel anvil/cutter bar
Double-banded belt drive
Chipper Blade Kit: P/N: 72493
66cm (26") rotor weighing 74.8kg (165 lbs.) fully assembled
•
•
•
•
•
•
•
•
•
•
•
2.5cm (1") thick machine balanced cantilever rotor
Chipper Models: CH6730H & CH611DH
17cm (6.7") square discharge chute
16.5cm x 34.3cm (6.5" x 13.5") feed chute for easy feeding of limbs
Four reversible heat-treated steel chipper blades
Four-sided anvil/cutter bar mounted on the side of the feed chute
Triple-banded belt
New style local sensing two-stage pump with live hydraulics
SmartFeed Sensor
Hand-operated belt engagement lever
•
•
•
•
•
•
•
•
23cm (9") machine – Model CHF9540H
15cm (6") diameter square discharge. Discharges toward the ground from a height of 86cm (34")
23cm x 23cm (9" x 9") feed throat opening
16 reversible heat-treated steel chipper blades
Triple-banded belt drive
•
•
•
•
•
•
•
•
•
10
20.3cm (8") and 23cm (9") machines
Models CH8720iH, CH8993H, CH8540, CH9540H, CH911DH & CH922DH – same chipper body
20.3cm (8") discharge chute rotating 360 degrees
23cm x 23cm (9" x 9") feed throat opening
Four reversible heat-treated steel chipper blades
Triple-banded belt drive, except model CH800H is hydraulic driven – no belts
CHIPPER/SHREDDERS
4cm CAPACITY CHIPPER/SHREDDER
Model: SC2170
ENGINE
DISCHARGE SCREEN
• Max torque: 11.25 Nm (8.3 ft-lbs.) at 2,500 rpm, runs at
3,800 rpm
MACHINE DIMENSIONS AND WEIGHT
FUEL CAPACITY
• 54.4kg (120 lbs. )
• Comes standard with 2.9cm screen (1.13")
• Subaru SP 170cc
• 3.4 liters (.9 gal.)
• LxWxH – 74cm x 58cm x 127cm (29" x 23" x 50")
SAFETY
DIRECT DRIVE
• Meets ISO safety decal standards
FEED CHUTES
• Shredder hopper is 40.6cm x 50.8cm (16" x 20")
PARTS & ACCESSORIES
• Standard Screen 2.8cm (1.13") (P/N: 76758-35)
• Maximum shredder capacity of up to 2cm (.75")
• Fine Screen 2cm (.75" ) (P/N: 76893-35)
• Maximum chipper feed size of up to 5cm (2")
• Wet Debris Screen (P/N: 77639-35)
CHIPPING BLADES & SHREDDING KNIVES
• Shredder Knives Kit (P/N: 77616-00)
• Two reversible heat-treated steel chipper blades
• Additional Shredder Knives Kit (P/N: 77618-00)
• Blade Dimensions: 8cm x 5cm x .6cm (3.125" x 2" x .25")
• Chipper Blade Kit (P/N: 70738)
• Four reversible Shredder Knives (standard)
• Hour/Tach Kit (P/N: 31605-00)
• Four additional Shredder Knives optional
CHIPPER/SHREDDER ROTOR ASSEMBLY
• Rotor weight is 6.8kg (15 lbs.)
• Rotor turns at 3,800 rpm
• 32.6cm (12.8") diameter
EASY TO TRANSPORT
• Easy grip wide handle
• Weight of machine is distributed evenly throughout
SC2170 Debris Screens
1.9cm Fine
011 + 1 + 701.282.5520
2.87cm
Standard
Wet
Debris
11
CHIPPER/SHREDDERS
8cm CAPACITY CHIPPER/SHREDDERS
1 of 2
Models: SC3206, SC3265, SC3305 & SC3342
ENGINES
SC3206
• Briggs & Stratton OHV 206cc
• Max torque: 12.2 Nm (9 ft-lbs.) at 2,700 rpm, runs at
3,600 rpm
SC3206
• Weighs 9.5kg (21 lbs.)
SC3305
• 30.4cm (12") diameter
3,600 rpm
SC3265, SC3305, SC3342
SC3265
• Subaru EX 265cc
3,800 rpm
SC3342
3,600 rpm
• Rotates at 3,600 rpm
• 2.5cm (1") diameter rotor shaft
• 2.5cm (1") diameter rotor shaft
• 30.4cm (12") diameter
CHIPPER BLADES & SHREDDER KNIVES
• Two reversible heat-treated chipper steel blades
• Blade Dimensions: LxWxH: 7.6cm x 5cm x 6cm
(3.125" x 2"x .25")
• Eight Reversible Shredder Knives – SC3206
FUEL CAPACITY
• Twelve Reversible Shredder Knives
SC3265, SC3305, SC3342
• SC3265 - 6.1 liters (1.6 gal.)
BEARINGS
• SC3206 - 3 liters (.8 gal.)
• SC3305, SC3342 - 3.8 liters (1 gal.)
• Two 2.5cm (1") greasable bearings with three bolt cast
flanges
BELT DRIVE
• Manual belt engagement
• SC3206, SC3305 – single belt driven
• SC3265, SC3342 – dual belt driven
• Spring-loaded belt tensioner
FEED CHUTES
• Shredder hopper is 30.5cm x 63.5cm (12" x 25")
• Maximum chipper feed size of up to 7.6cm (3")
SIDE DISCHARGE
• You don’t have to move the equipment as often with a side
discharge as you do with a bottom discharge
• Heavy-duty 4.76mm (7 gauge) steel screens available
in four different sizes to fit your needs
CONVENIENT TRANSPORTATION
• Shredder hopper handle for ease of transporting
• Pneumatic tires feature grease zerks, enabling easy
greasing of the hub
12
CHIPPER/SHREDDERS
8cm CAPACITY CHIPPER/SHREDDERS
2 of 2
Models: SC3206, SC3265, SC3305 & SC3342
HEAVY-DUTY CONSTRUCTION
• Extra strength and reinforcements in areas that matter
most
• 1.98mm (14 gauge) steel construction
• Built to last with welded construction instead of bolt
together
MACHINE DIMENSIONS
PARTS & ACCESSORIES (Cont.)
SC3206
• Screen - Fine .95cm (.375" ) (P/N: 77382-12)
• Screen - Medium 2cm (.75") (P/N: 77383-12)
• Screen - Coarse Standard 3.5cm (1.375") (P/N: 77384-12)
• Screen - Wet Debris (P/N: 77385-12)
• Shredder Knives Kit – SC3206 (P/N: 77589-00)
SC3265, SC3305, SC3342
WEIGHTS
• SC3206 - 106.6.5kg (235 lbs.)
• SC3265 - 131.5kg (290 lbs.)
• Screen - Fine .95cm (.375" ) (P/N: 77386-12)
• Screen - Medium 2cm (.75") (P/N: 77387-12)
• Screen - Coarse Standard 3.5cm (1.375") (P/N: 77388-12)
• SC3305 - 121.6kg (268 lbs.)
• Screen - Wet Debris (P/N: 77389-12)
• SC3342 - 137.4kg (303 lbs.)
• Blower Attachment (P/N: 70251)
PARTS & ACCESSORIES
• Shredder Knives Kit (P/N: 70973)
• Two-Wheel Tow Kit (P/N: 77000-00)
• Leaf Tamper (P/N: 70089)
• Debris Bag with Handles (P/N: 17854)
• All Weather Cover (P/N: 70093)
• Tach/Hour Meter (P/N: 31605-00)
Debris Screens
.95cm
1.9cm
3.5cm
Standard
Wet
Debris
A 3.5cm debris screen is standard with three others
available depending on desired mulch size/type.
011 + 1 + 701.282.5520
13
CHIPPER/SHREDDER/BLOWER
13cm CAPACITY CHIPPER/SHREDDER/BLOWER
Model: SC5720B
ENGINE
• Subaru EH 720cc
DOUBLE-BANDED BELT DRIVE
• Manual belt engagement
3,600 rpm
FUEL CAPACITY
• Shredder hopper is 33cm x 48.7cm (13" x 18")
• 34.1 liters (9 gal.)
• Machine balanced
• 3.8cm (1.5") diameter rotor shaft
• Easily accessible through the hinged cover, when open it
exposes one half of the rotor for easy access to the chipping blades and makes for easy clean out
CHIPPER BLADES & SHREDDER KNIVES
• Four reversible heat-treated chipper steel blades
FEED CHUTES
INTEGRATED DISCHARGE
• With a 360° rotatable, 15.25cm (6") diameter steel
tubing with adjustable spout cap allows you to put the
chips where you want them the first time
• Discharge height is 234cm (92")
UNIQUE SCREENLESS SHREDDER
• Unique product, self-feed chipper/shredder without a
screen. This greatly reduces the chance of plugging,
especially with damp material
• Blade Dimensions: 7.6cm x 5cm x 6cm
(3.125" x 2" x .25")
• 4.76mm (7 gauge) steel
• 36 Shredder Knives
• 127cm (50") tread width (center to center) and 5.3-12
tires with 454kg (1,000 lb.) torsion axle suspension
enables the chipper to be easily towed down the highway
BEARINGS
• Two 3.8cm (1.5") greasable bearings with two bolt
cast flanges
HIGHWAY TOWABLE
TOWING WEIGHT
• 437.7kg (965 lbs.) with fluids at capacity
HITCH
• 50mm coupler with handle
MACHINE DIMENSIONS
SAFETY
• Safety chains
• 12 volt tail lights standard
• Meets NATM Certification
PARTS & ACCESSORIES
• Shredder Knives Kit (P/N: 77613-00)
14
STUMP GRINDER
Model: SG340
ENGINE
MACHINE DIMENSIONS
DOUBLE-BANDED BELT DRIVE SYSTEM
WEIGHT
• Reduces belt maintenance greatly
SAFETY
• Honda GXV 340cc
• Double-banded belt driving the cutter head for more
positive power transfer. Belt tension idler
• 88kg (195 lbs.)
CARBIDE TIPPED TEETH
• 12 carbide tipped teeth offer maximum cutting
performance. These teeth are locked into the cutter head
(8 curved, 4 straight teeth)
PARTS
• 12 Blade C
utter Replacement Kit (P/N: 76292-00)
• The cutter head turns at 3,600 rpm with a speed at the
tips 2578 m/min (8,460 ft/min)
• A screen covered opening increases visibility to the
cutter head
17.8cm (7") DIAMETER CUTTER HEAD
• Large cutting diameter giving a smooth cut and can be
easily removed for quick and easy sharpening
• Cutter head at 15 degree angle
• Designed for use on stumps from 15.2cm (6") above grade
to a maximum of 10.2cm (4") below grade
DEBRIS FLAP
• Mounted to the stump grinder axle
LARGE ENCLOSED DRIVE SHAFT
• Prevents chips from building up in the belts and pulleys
• Large 3.8cm (1.5") diameter drive shaft provides superior
reliability
40.64cm (16") PNEUMATIC WHEELS
• Pneumatic tires 4.80-8 rim with ball bearing hub
SINGLE WHEEL BRAKE
• Allows the stump grinder to pivot and keep in position
while grinding effortlessly
ENGINE KILL SWITCH
• Safety feature to shut engine off if disengaged for
added safety
Single Wheel Brake
011 + 1 + 701.282.5520
12 Blade Cutter
Replacement Kit
P/N: 76292-00
15
CHIPPERS
10cm CAPACITY CHIPPER
Model: CH4400
ENGINE
• Subaru EX 404cc
• Tongue is 5cm x 5 cm (2" x 2") with 3.18mm (11 gauge)
wall thickness
• Max torque: 27.1Nm (20 ft-lbs.) achieved at 2,400 rpm
operates at 3,800 rpm
HIGHWAY TOWABLE
FUEL CAPACITY
• 7 liters (1.85 gal.)
35.6cm (14") DIAMETER CANTILEVER ROTOR
• 35.6cm (14") diameter by 2.5cm (1") thick rotor
TWO CHIPPING BLADES
• Blade Dimensions: 12.7cm x 10.2cm x 1.3cm
(5" x 4" x .5")
BEARINGS
• Two 3.2cm (1.25") greasable bearings with
two bolt cast flanges
BELT DRIVE
• 43" (109cm) tread width (center to center) and
4.80-8 tires with 454kg (1,000 lb.) torsion axle
suspension enables the chipper to be easily towed
down the highway
• 12 volt safety and directional lighting and tow chains are
standard
TOWING WEIGHT
• 264kg (582 lbs.)
HITCH
MACHINE DIMENSIONS
SAFETY
• Safety chains
PARTS & ACCESSORIES
• Double-banded belt drive with manual belt engagement
• Blade Kit (P/N: 76295-00)
• Optional Discharge Chute
11.4cm x 11.4cm (4.5" x 4.5") (P/N: 74634-00)
ANVIL/CUTTER BAR
• Four-sided adjustable to insure good chipping ability
• Tach/Hour Meter Kit - Gas (P/N: 31605-00)
• 12.7cm long x 4.4cm wide x .95cm thick
(5" long x 1.75" wide x .375" thick)
FEED CHUTE
• Opening 33cm x 38cm (13" x 15"), 124.5cm (49")
off the ground
• Feed throat opening is 12.7cm x 12.7cm (5" x 5")
• Maximum feed size of up to 10cm (4")
• Standard Discharge
11.4cm x 22.9cm (4.5" x 9") and discharges towards the
ground, from a height of 36cm (14")
• Optional Discharge
11.4cm x 11.4cm (4.5" x 4.5") square discharge with adjustable deflector, discharges at a height of 140cm (55")
• 4.76mm (7 gauge) steel throughout housing with welded
construction
• Trailer is made of 4.76mm (7 gauge) steel
16
CHIPPERS
13cm CAPACITY CHIPPER
Model: CH5653
ENGINE
• Subaru EH engine 653cc
3,800 rpm
FUEL CAPACITY
51cm (20") DIAMETER ROTOR
• 51cm (20") diameter by 3.2cm (1.25") thick rotor
HIGHWAY TOWABLE
• 112cm (44") tread width (center to center) and 5.30-12
tires with 454kg (1,000 lb.) torsion axle suspension enables the chipper to be easily towed down the highway
• 12 volt safety and directional lighting and tow chains are standard
TOWING WEIGHT
• 446.8kg (985 lbs.)
HITCH
MACHINE DIMENSIONS
exposes one half of the rotor for easy access to the chipping blades and makes for easy clean out
SAFETY
FOUR CHIPPING BLADES
• Blade Dimensions: 7.9cm x 5cm x .6cm (3.1" x 2" x .25")
PARTS & ACCESSORIES
BEARINGS
• Four reversible heat-treated steel chipper blades
• Safety chains
• Blade Kit (P/N: 72493)
• Two 3.8cm (1.5") greasable bearings
with two bolt cast flanges
BELT DRIVE
ANVIL/CUTTER BAR
• Four-sided adjustable
• 14.2cm long x 10.2cm wide x .95cm thick (5.6" long x 4"
wide x .375" thick)
FEED CHUTE
• Opening 68.6cm x 71.1cm (27" x 28")
115.6cm (45.5") off the ground
• Feed throat opening is 14cm x 15.2cm (5.5" x 6")
• Maximum feed size of up to 12.7cm (5")
•With a 360° rotatable, 15.2cm (6") diameter steel tubing
with adjustable spout cap allows you to put the chips where
you want them the first time
• Discharge height is 2.4m (95")
• 6.35cm (.25") steel housing with welded
construction
•Trailer is made of 4.76mm (7 gauge) steel
• Tongue is 5cm x 5 cm (2" x 2") with 6.35mm (.25")
wall thickness
011 + 1 + 701.282.5520
17
CHIPPERS
15cm CAPACITY CANTILEVER CHIPPERS -
1 of 2
Models: CH611DH & CH6730H
ENGINES
CH611DH
• Kubota 1.1 Liter Diesel, 69 cu in. (1.1 liter)
• Max torque: 73.5 Nm (54.2 ft-lbs.) achieved at 2,200 rpm
• Operates at 3,220 rpm
CH6730H
• Kohler 730cc
• Max torque: 55.5 Nm (40.9 ft-lbs.) achieved at 2,400 rpm
HYDRAULIC FEED SYSTEM
• Steel hydraulic reservoir, 15 liters (4 gal.) capacity on
CH611DH and a Nylon hydraulic reservoir,
11.5 liters (3 gal.) capacity on the CH6730H
• Self-contained hydraulic feed system allows you to evenly
feed limbs into the chipper
• Variable feed rate on the CH611DH (available as
an accessory on the CH6730H) with load sensing
2-stage pump
• Feed rate 0-46 m/min (0-150 fpm)
Average 30 m/min (100 fpm)
FUEL CAPACITY/CONSUMPTION
• Self-contained system with infinite speed settings,
dedicated neutral and full reverse, pump output
25 LPM (6.6 GPM) and 4hp with maximum
pressure and maximum flow, however
this is rarely required
• Fuel consumption on the Kohler 730cc is estimated at
8 liters (2.1 gal.) per hour at full load
• Fuel consumption on the Kubota 1.1 L is estimated at
6.44 liters (1.7 gal.) per hour at full load
66cm (26" ) DIAMETER ROTOR
• 66cm (26") diameter by 2.5cm (1") thick rotor
• Weighs 75kg (165 lbs.)
• Rotates at 1,780 rpm (CH611DH)
• Rotates at 1,650 rpm (CH6730H)
• Easily accessible through the hinged cover, when
open it exposes one half of the rotor for easy access to the chipping blades and makes for easy clean out
• Feed system operates under 2,500 psi
• Single 38cm (15") diameter top feed roller
• 2-stage pump
PLUS+1® ELECTRONIC CONTROLLER
• Smart feed with automatic “try again” feature to clear jams
• Maximizes chipping efficiency and manpower
• Minimizes fuel consumption
• Provides an Amber code that alerts the operator every
15 hours to inspect chipping blades
FEED CHUTE
• Opening 84cm x 94cm (33" x 37") tray 76.2cm (30") off
the ground
• Feed throat opening is 16.5cm x 33cm (6.5" x 13")
(5" x 4" x .5")
• 90° feed angle
BEARINGS
• Two 4.5cm (1.75") greasable bearings with four bolt cast
flanges
BELT DRIVE
• Maximum feed size of up to 15.2cm (6")
CH6730H
tubing with adjustable spout cap
• Triple-banded belt drive with manual belt engagement
CH611DH
ANVIL/CUTTER BAR
• With a 360° rotatable, 17cm (6.7") square steel chute with
screw-type adjustable spout cap
• Four-sided adjustable anvil to insure good chipping ability
• 16.5cm long x 10.2cm wide x 1.6cm thick (6" long x 4" wide
x .625" thick)
18
CHIPPERS
15cm CAPACITY CANTILEVER CHIPPERS -
2 of 2
Models: CH611DH & CH6730H
• .25" (6.35cm) housing with welded construction
• Feed table is 3.57mm (10 gauge) steel on the CH6730H
and 4.76mm (7 gauge) steel on the CH611DH
• Tongue is 7.6cm x 7.6 cm (3" x 3") with 3.18mm (11
gauge) wall thickness
HIGHWAY TOWABLE
CH6730H
• 127cm (50") tread width (center to center) and
P205-75R14 tires with 816kg (1,800 lb.) torsion
axle suspension
CH611DH
• 127cm (50") tread width (center to center) and
P215-75R15 tires with 1030kg (2,500 lb.) torsion
axle suspension
TOWING WEIGHT
MACHINE DIMENSIONS
CH611DH
CH6730H
SAFETY
• Safety chains (CH6730H only)
PARTS & ACCESSORIES
• Blade Kit (P/N: 76293-00)
• Spare Tire Kit (CH611DH)(P/N: 75291-00)
• Adjustable Feed Speed Sensor Kit (P/N: 76820-00)
• CH611DH – 1,052kg (2,320 lbs.)
• CH6730H – 750kg (1,655 lbs.)
HITCH
ADJUSTABLE TONGUE JACK
• Roller wheel with 385kg (850 lbs.) rating
• Adjustable jack allows one person to easily maneuver
the chipper around and hook up to a vehicle
Cantilever-Mounted Rotor on these Models
011 + 1 + 701.282.5520
19
CHIPPERS
20cm CAPACITY TURNTABLE CHIPPERS -
1 of 2
Models: CH8720iH & CH8993H
ENGINES
CH8720iH
• EFI Subaru EH 720cc, Fuel injected
• Max torque: 52.2 Nm (38.5 ft-lbs.) at 2,800 rpm
(5" x 4" x .5")
BEARINGS
• Two 4.5cm (1.75") greasable bearings with 4 bolt castflanges
CH8993H
• Briggs & Stratton Vanguard 993cc
• Max torque: 71 Nm (52.4 ft-lbs.) at 2,350 rpm
BELT DRIVE
ANVIL/CUTTER BAR
• Fuel consumption on the Briggs & Stratton 993cc is
estimated at 11.3 liters (3 gal.) per hour at full load
• 22.9cm long x 8.9cm wide x 1.6cm thick
(9" long x 4" wide x .625" thick)
• Fuel consumption on the EFI Subaru EH 720cc is
estimated at 5.7 liters (1.5 gal.) per hour at full load
• Steel hydraulic reservoir, 11.5 liters (3 gal.) capacity
• Variable feed rate with load sensing 2-stage pump
• Easily accessible through the hinged cover, when open
it exposes one half of the rotor for easy access to the chipping blades and makes for easy clean out
• Self-contained system with infinite speed settings,
dedicated neutral and full reverse, pump output 25 LPM
(6.6 GPM) and 4hp with maximum pressure and maximum
flow, however this is rarely required
• Single 15" (38cm) diameter top feed roller
• 2-stage pump
CH8993H
Shown
Heavy Duty Rotors
20
CHIPPERS
20cm CAPACITY TURNTABLE CHIPPERS
2 of 2
Models: CH8720iH & CH8993H
HIGHWAY TOWABLE
• 174cm (69" ) tread width (center to center) and
P215-75R15 tires with 1360kg (3,000 lb.) torsion axle
suspension enables the chipper to be easily towed down
the highway
• Provides an Amber code that alerts the operator every 15
hours to change chipping blades
TOWING WEIGHT
FEED CHUTE
• CH8993H – 1,075kg (2,370 lbs.)
• Opening 76cm x 79cm (30" x 31")
Tray 68cm (27") off the ground
• Feed throat opening is 23cm x 23cm (9" x 9")
• 90° Feed Angle
• With a 360° rotatable, 20cm (8") diameter steel tubing
• .95cm (.375") steel face plate on the rotor housing
• 6.35cm (.25") steel on the rest of the housing
• Frame is 5cm x 5cm (2.5" x 2.5") with 4.76mm (7 gauge)
tubing
• CH8720iH – 1,018kg (2,245 lbs.)
HITCH
MACHINE DIMENSIONS
360° ROTATIONAL BED
• Bed can rotate 360° for ease of feeding from any direction
• Brake for locking bed in place. With drop pin for positive
transport lock
• Keeps work crews out of the street
SAFETY
PARTS & ACCESSORIES
• Feed table is 3.57mm (10 gauge) steel
• Blade Kit (P/N: 76293-00)
• Tongue is 7.6cm x 7.6cm (3" x 3") with 6.35mm (.25")
wall thickness
• Low Profile Discharge Chute Kit (P/N: 74581-00)
CH8993H
Shown
011 + 1 + 701.282.5520
21
CHIPPERS
23cm CAPACITY -
1 of 2
Models: CH911DH & CH922DH
ENGINES
ANVIL/CUTTER BAR
• Kubota engine 1.1 Liter Diesel, 1.1 liter (69 cu in.)
• Max torque: 71 Nm (54.2 ft-lbs.) achieved at 2,200 rpm
CH922DH
• Steel hydraulic reservoir, 11.5 liters (3 gal.) capacity
• Kubota engine 2.2 Liter Diesel, 2.2 liter (134 cu in.)
CH911DH
• Max torque: 147 Nm (108.4 ft-lbs.) achieved at 1,800
rpm
• 68 liters (18 gal.)
• Fuel consumption on the 1.1 Liter Diesel Kubota is
estimated at 7.57 liters (1.7 gal.) per hour at full load
• Variable feed rate with load sensing two-stage pump
• Self-contained system with infinite speed settings, dedicated neutral and full reverse, pump output 25 LPM (6.6
GPM) and 4 hp with maximum pressure and maximum
flow, however this is rarely required
• Fuel consumption on the 2.2 Liter Diesel Kubota is
estimated at 14.2 liters (3 gal.) per hour at full load
• 2-stage pump
• 76cm (30" ) diameter by 3.2cm (1.25") thick rotor
15 hours to change chipping blades
• Easily accessible through the hinged cover, when
open it exposes one half of the rotor for easy access to the chipping blades and makes for easy clean out
FEED CHUTE
• Opening 76cm x 79cm (30" x 31")
(5" x 4" x .5")
• 90° Feed Angle
BEARINGS
• Two 4.5cm (1.75") greasable bearings with four bolt cast flanges
• Feed table is 96.5cm (38") long
BELT DRIVE
with adjustable spout cap allows you to put the chips
where you want them the first time
• Discharge height is 2.4m (96" )
22
CHIPPERS
23cm CAPACITY -
2 of 2
Models: CH911DH & CH922DH
• 6.35mm (.25") steel on the rest of the housing
• 10cm (4") "C" Channel frame construction
TOWING WEIGHT
• CH911DH – 1,125kg (2,480 lbs.)
• CH922DH – 1,225kg (2,700 lbs.)
MACHINE DIMENSIONS
• LxWxH – 271.8cm x 200cm x 244cm (107" x 79" x 96")
SAFETY
PARTS & ACCESSORIES
• Blade Kit (P/N: 76293-00)
• Electric Brake Kit (P/N: 72730)
• Fine Chip Rotor Kit (P/N: 76775-00)
• Hour Meter Kit - Diesel (P/N: 71921)
Hitch pole, axle and wheels shown in picture for illustratration
purposes only. CH911DH & CH922DH models do not include
hitch, axle and wheels for CE compliant models.
011 + 1 + 701.282.5520
23
PTO MACHINES
11cm CAPACITY
Model: CH45540
PTO DRIVE
ANVIL/CUTTER BAR
• Recommend 11-21kW (15-28 hp) at the PTO
(5.6" long x 4" wide x .375" thick)
• 540 rpm input
35.6cm (14") DIAMETER ROTOR
CHIPPER BLADES
(5" x 4" x .5")
BEARINGS
• Two 3.2cm (1.25") greasable bearings with two bolt cast flanges
FEED CHUTE
• Opening 40.6cm x 58.4cm (16" x 23"), 129.5cm (51")
off the ground
• Feed throat opening is 11.4cm x 12.7cm (4.5" x 5")
• Maximum feed size of up to 11.4cm (4.5")
• Standard discharge is 11.4cm x 11.4cm (4.5" x 4.5")
and discharges towards the ground, from a height of
38cm (14.9")
• Optional Discharge is 11.4cm x 11.4cm (4.5" x 4.5") discharges with adjustable deflector at a height of
140cm (55")
BELT DRIVE
• 4.76mm (7 gauge) steel throughout housing with welded construction
3-POINT HITCH
• Double-banded belt drive
• Category 1
• Chipper weight is 185.5kg (409 lbs.)
MACHINE DIMENSIONS
• LxWxH – 134.6cm x 104cm x 144.8cm (53" x 41" x 57")
SAFETY
PARTS & ACCESSORIES
• Blade Kit (P/N: 76295-00)
• Optional Discharge Chute 11.4cm x 11.4cm (4.5" x 4.5")
(P/N: 74634-00)
24
PTO MACHINES
13cm CAPACITY
Models: CH5540 & CH5540H
PTO DRIVE
HYDRAULIC FEED SYSTEM (CH5540H)
• Maximum capacity of 11.36 liters/minute (3 gal.) at
2,500 psi
• 540 rpm input
51cm (20") DIAMETER ROTOR
• Rotates at 1,615 rpm (CH5540)
• Rotates at 1,630 rpm (CH5540H)
• 3.8cm (1.5" ) diameter rotor shaft
• Easily accessible through the hinged cover, when open it exposes one half of the rotor for easy access to the chipping blades and makes for easy clean out
CHIPPER BLADES
• Blade Dimensions: 7.9cm x 5cm x .64cm (3.1" x 2" x .25")
BEARINGS
• Two 3.8cm (1.5") greasable bearings with two bolt cast flanges.
BELT DRIVE
ANVIL/CUTTER BAR
• Electric/Hydraulic System to control feed roller direction
• 2-stage hydraulic pump
15 hours to change chipping blades
FEED CHUTE
• Opening 71cm x 71cm (28" x 28")
• Feed throat opening is 14cm x 19cm (5.5" x 7.5")
• Maximum feed size of 13cm (5")
tubing with adjustable spout cap allows you to put the
chips where you want them the first time
• 6.35mm (.25") steel throughout housing with welded construction
CATEGORY 1 3-POINT HITCH
(5.6" long x 4" wide x .375" thick)
• CH5540H - Weight is 453.6kg (1000 lbs.)
• CH5540 - Weight is 281.2kg (620 lbs.)
MACHINE DIMENSIONS
• CH5540 – LxWxH 127cm x 114cm x 229cm
(50" x 45" x 90")
• CH5540H – LxWxH 173cm x 124cm x 229cm
(68" x 49" x 90")
SAFETY
PARTS & ACCESSORIES
• Blade Kit (P/N: 72493)
• Auto Feed Kit - CH5540H (P/N: 73071)
011 + 1 + 701.282.5520
25
PTO MACHINES
13cm CAPACITY CHIPPER/SHREDDER/BLOWER
Model: SC5540B
POWER SOURCE
• 540 rpm input
• Easily accessible through the hinged cover, when open it exposes one half of the rotor for easy access to the chipping blades and makes for easy clean out
• 4.76mm (7 gauge) reinforced steel bed
MACHINE DIMENSIONS
• Weight: 342.5kg (755 lbs.)
SAFETY
PARTS & ACCESSORIES
• Shredder Knives Kit (P/N: 70972)
CHIPPER BLADES & SHREDDING KNIVES
• Four reversible heat-treated chipper steel blades
• Blade Dimensions: 7.9cm x 5cm x .64cm
(3.125" x 2" x .25")
• 36 Reversible Shredding Knives
BEARINGS
• Two 3.8cm (1.5") greasable bearings with two bolt cast
flanges
BELT DRIVE
FEED CHUTES
• Shredder hopper is 33cm x 51cm (13" x 20")
140.5cm (55.3") off the ground
tubing with adjustable discharge
UNIQUE SCREENLESS SHREDDER
• Unique product, self-feed chipper/shredder without a
screen
26
PTO MACHINES
20cm CAPACITY
Model: CH8540
PTO DRIVE
ANVIL/CUTTER BAR
• Recommend 26kW-45kW (35hp to 60hp) at the PTO
• 540 rpm input
• 4.5cm (1.75")-diameter rotor shaft
• Four-sided adjustable anvil
FEED CHUTE
• Opening 76cm x 79cm (30" x 31")
149cm (58.75") off the ground
• Easily accessible through the hinged cover, when opened,
it exposes one half of the rotor for easy access to the chipping blades and makes for easy clean out
CHIPPER BLADES
(5" x 4" x .5")
BEARINGS
• 6.35mm (.25") steel on the wrap around with welded construction
• Two 4.5cm (1.75") greasable bearings with 4 bolt cast flanges
BELT DRIVE
• Triple-banded belt drive
• Frame is 5cm x 5cm (2" x 2"), 4.76mm (7 gauge) thick
steel
3-POINT HITCH
• Category 1
MACHINE DIMENSIONS
• Weight: 411kg (906 lbs.)
SAFETY
PARTS & ACCESSORIES
• Blade Kit (P/N: 76293-00)
011 + 1 + 701.282.5520
27
PTO MACHINES
23cm CAPACITY
1 of 2
Models: CH9540H & CHF9540H
PTO DRIVE
• 540 rpm input
BEARINGS
• Recommend 26kW-45kW (35hp to 60hp) at the PTO
• Two 4.5cm (1.75") greasable bearings with 4 bolt cast
flanges
76CM (30") DIAMETER ROTOR
BELT DRIVE
• Triple-banded belt drive
ANVIL/CUTTER BAR
• Four-sided adjustable anvil
• 22.9cm long x 10.2cm wide x 1.6cm thick (9" long x 4"
wide x .625" thick)
exposes one half of the rotor for easy access to
the chipping blades and makes for easy clean out
CHIPPER BLADES
• Steel hydraulic reservoir, 11.5 liter (3 gal.) capacity
• Self-contained hydraulic feed system allows you to evenly feed limbs into the chipper
CH9540H
• Variable feed rate with load sensing two-stage pump
(5" x 4" x .5")
• 16 reversible heat-treated steel chipper blades
• Self-contained system with infinite speed settings, dedicated neutral and full reverse, pump output
25 LPM (6.6 GPM) and 4Hp with maximum pressure and
maximum flow, however this is rarely required
• Blade Dimensions: 7.9cm x 5cm x .6cm ( 3.1" x 2" x .25")
• Blades are spaced on the rotor to provide maximum coverage and produce an extremely small chip
CHF9540H
28
• 2-stage hydraulic pump
PTO MACHINES
23cm CAPACITY
2 of 2
Models: CH9540H & CHF9540H
3-POINT HITCH
• Category 1
• Chipper weight is 598.7kg (1,320 lbs.)
MACHINE DIMENSIONS
15 hours to inspect chipping blades
FEED CHUTE
• Opening 76cm x 79cm (30" x 31")
CH9540H
CHF9540H
SAFETY
• 90° feed angle
PARTS & ACCESSORIES
• Blade Kit for model CH9540H (P/N: 76293-00)
CH9540H
• Blade Kit for model CHF9540H (P/N: 74830-00)
• 360° rotatable, 20cm (8") diameter steel
tubing with adjustable spout cap discharges
from a height of 236cm (93")
• Fine Chip Rotor Kit (P/N: 76775-00)
CHF9540H
• 15cm (6") diameter square discharge. Discharges toward
the ground from a height of 86cm (34")
• 6.35mm (.25") steel on the rest of the housing
• Frame is 5cm x 5cm (2" x 2" ), 4.76mm (7 gauge) thick
steel
011 + 1 + 701.282.5520
29
SKID STEER CHIPPERS
11cm CAPACITY
Model: CH450H
SKID-STEER MOUNT
• CH450 fits mini skid steer
Minimum: 41.6 LPM - Maximum: 56.8 LPM
(Minimum: 11 GPM - Maximum: 15 GPM)
ANVIL/CUTTER BAR
• Easy to attach just connect chipper to the SAE J2513
Quik-Attach, attach the hydraulic hoses, and you are ready
to go
• The CH450H's standard discharge is 11.4cm x 22.9cm
(4.5" x 9") and discharges towards the ground, from a
height of 27cm.
CHIPPER ROTOR
MACHINE DIMENSION & WEIGHT
• 181.4kg (400 lbs.)
SAFETY
• 134.6cm x 90cm x 127cm (53" x 35" x 50")
• Meets applicable CE safety standards
CHIPPING BLADES
PARTS
• Double-Edge Blade Kit (P/N: 76295-00)
• Dimensions: 12.7cm x 10.2cm x 1.3cm (5" x 4" x .5")
• Optional Discharge Chute 11.4cm x 11.4cm (4.5" x 4.5")
(P/N: 74634-00)
BEARINGS
• Two 3.2cm (1.25") greasable bearings with two bolt cast
flanges
30
WHEELED VACUUMS
Models: WV190 & WV190S
ENGINES
• WV190/WV190S – Briggs & Stratton
190cc Professional Series
FAN ROTOR
• 5-blade steel fan
• 6.35mm (.25") Steel welded rotor construction
ONE PIECE HOUSING
SAFETY
PARTS & ACCESSORIES
• Additional Debris Bag (P/N: 31339-00)
• Caster Wheels (P/N: 76967-00)
• 10.2cm (4") Diameter Hose Kit
(P/N: 73606-00)
• Made with .5cm (.20") thick Linear Low Density
Polyurethane with a UV inhibitor
• Durable Nozzle Wear Plate
(P/N: 73640-00)
• Easily removable adapter with bag
• Vacuum Wear Liner (P/N: 76466-00)
• Discharge opening 15cm x 16.27cm (6" x 6.5")
• Intake width 68.58cm (27")
SELF-PROPELLED
• 3 speed self-propelled
1st – 1.14 kph (.71 mph)
2nd – 1.5 kph (.93 mph)
3rd – 1.95 kph (1.21 mph)
• Self-propelled rear wheel drive provides more traction
• Ball bearing wheels for a smoother, easier ride
HANDLEBARS
• Four adjustable height settings
• Cushion Grip
BAG
• Large capacity, hard bottom, quick dump bag,
5-bushel capacity
• Dust reducing
• Heavy-duty, double stitched nylon zipper with
deflector flaps
• Adjustable hanger straps
ADJUSTABLE FRONT – FIVE HEIGHT SETTINGS
• .64cm (.25" ) above ground, ground level set at factory
• 3.175cm (1.25")
• 6.0cm (2.4")
• 8.89cm (3.5")
• 4.4cm (4.5")
MACHINE DIMENSIONS
• 155cm x 69cm x 117cm (61" x 27" x 46")
at maximum handle height
• WV190 – 51kg (113 lbs.)
• WV190S – 57kg (126 lbs.)
011 + 1 + 701.282.5520
31
DEBRIS LOADERS
HITCH MOUNT DEBRIS LOADERS
Models: DL8390 & DL10570
ENGINES
• DL8390
Honda GX 390cc with recoil start
• DL10570
Briggs & Stratton Vanguard 570cc with recoil start
FUEL CAPACITY
• DL8390 - 6 liters (1.6 gal.)
• DL10570 - 7.9 liters (2.1 gal.)
FAN AND HOUSING
• Wear liners made out of high strength steel
• 4-blade fan made of .9cm (.375") steel
• Scrolled fan housing for more efficient transfer of air
• Direct drive
• One bolt access cover removal for easy fan clean out
DISCHARGE CHUTE
• 360° Rotational 20.3cm (8") discharge chute
MACHINE DIMENSIONS
DL8390
DL10570
WEIGHTS
DL8390
• 127kg (280 lbs.)
DL10570
• 127kg (280 lbs.)
SAFETY
PARTS & ACCESSORIES
• Wear Liner Replacement Kit (P/N: 75768-00)
• 1.2 m (4') Flexible Horizontal Chute Extension
(P/N: 74737-00)
BUILT TO LAST
• Heavy-duty hose swivel boom
• 40.6cm (16") Vertical Chute Extension (P/N: 7588800)
• Light-weight aluminum handle
• Swing Away Hitch Mount Kit (P/N: 75739-00)
• 20.3cm (8") diameter 3.6m (12') long flex hose
(model DL8390)
• Tailgate Adapter Kit (P/N: 75753-00)
(model DL10570)
CFMS
• DL8390 – 2300
• DL10570– 2500
32
WHEELED
DEBRIS LOADERS
VACUUMS
SKID MOUNT DEBRIS LOADERS
Model: DL12653 & DL12720
ENGINES
CFMS
• Subaru EH 653cc with electric start
• DL12720 – 3400
DL12653
DL12720
• Subaru EH 720cc with electric start
FUEL CAPACITY
• 34.1 liters (9 gal.) Polyethylene tank
FAN AND HOUSING
• Wear liners made out of special high strength steel
• 4-blade fan made out of 9.5mm (.375") steel
• DL12653 – 3400
SAFETY
PARTS & ACCESSORIES
• Flexible Hose 30.5cm x 3.7m (12" x 12') (P/N: 12778)
• Wear Liner Replacement Kit (P/N: 77073-00)
• 40.6 cm (16") Vertical Chute Extension
(P/N: 75888-00)
• Scrolled fan housing for more efficient transfer of air
• 1.2m (4') Flexible Horizontal Chute Extension
(P/N: 74737-00)
DRIVE
• 12 Volt Work Light Kit (P/N: 77105-00)
DL12653
• Direct drive
DL12720
DISCHARGE CHUTE
• 360° rotational 20cm (8" )
BUILT TO LAST
• Heavy-duty swivel boom with hose storage
• Lightweight aluminum handle
• One bolt access cover removal for easy fan clean out
MACHINE DIMENSIONS
DL12653
DL12720
WEIGHTS
DL12653
• 269.9 kg (595 lbs.)
DL12720
• 306.2 kg (675 lbs.)
Model shown with optional trailer.
Trailer is not available in CE compliant required areas.
011 + 1 + 701.282.5520
33
ECHO BEAR CAT GEAR
REUSABLE V INYL
E ARPLUGS W ITH CASE
The handy carrying case can be worn on your belt
when not in use. Cleanup is easy with just warm
water. CE and OSHA approved.
P/N: 31539-00
E AR MUFFS
These light-weight ear
muffs have an NRR of
29 dB(A) when used
as directed and meet
CE standard 3.19.
P/N: 36775-00
CE EN352-1:2002
SAFET Y GL ASSES
HELMET SYSTEM
Lightweight and impact resistant. Hard-coated opticalgrade, abrasion resistant lenses. Polycarbonate lenses
offer 99.9% protection from the most intense UV rays.
Includes
helmet, mesh
face visor and
ear protection.
P/N: 36776-00
Tech Glasses
P/N: 36773-00
Zone II Glasses
P/N: 36774-00
PREMIUM SAFET Y
VEST
Highly visible vest features
5-point tear away
panels for safety.
P/N: 36777-00 (large)
P/N: 36778-00 (xlarge)
P/N: 36779-00 (xxlarge)
ISEA 107-2004
34
CE EN397:1995 CLASS EG & C
CE EN1663B
CE EN352-3:1997
V IBR AT ION-REDUCING
SPOR T/L ANDSCAPE GLOVES
Premium, padded-leatherpalm gloves help reduce
vibration. Also feature form
fitting fingers and
Velcro® -type wrist
band for tight fit.
P/N: 31299-00 (large)
P/N: 31300-00 (xlarge)
NOTES
011 + 1 + 701.282.5520
35
WARRANTY COVERAGE
CURRENT MODELS
PRODUCT
1 of 2
ECHO BEAR CAT WARRANTY
CHIPPER/SHREDDER
MODEL
ENGINE
CONSUMER
COMMERCIAL
RENTAL
PARTS
LABOR
SC2170
170cc Subaru
2 year
N/A
N/A
YES
YES
SC3206
205cc B&S
2 year
N/A
N/A
YES
YES
SC3265
265cc Subaru
2 year
1 year
6 mo.
YES
YES
SC3305
305cc B&S
2 year
1 year
6 mo.
YES
YES
SC3342
342cc B&S
2 year
1 year
6 mo.
YES
YES
SC5540B
N/A
2 year
1 year
6 mo.
YES
YES
SC5720B
720cc Subaru
2 year
1 year
6 mo.
YES
YES
CHIPPERS
36
MODEL
ENGINE
CONSUMER
COMM.
RENTAL
PARTS
LABOR
CH4400
404cc Subaru
2 year
1 year
6 mo.
YES
YES
CH45540
N/A
2 year
1 year
6 mo.
YES
YES
CH5540
N/A
2 year
1 year
6 mo.
YES
YES
CH5540H
N/A
2 year
1 year
6 mo.
YES
YES
CH5653
653cc Subaru
2 year
1 year
6 mo.
YES
YES
CH611DH
1.1 Liter Kubota
2 year
1 year
6 mo.
YES
YES
CH6730H
730cc Kohler
2 year
1 year
6 mo.
YES
YES
CH8720iH
720cc Subaru
2 year
1 year
6 mo.
YES
YES
CH8993H
993cc B&S
2 year
1 year
6 mo.
YES
YES
CH8540
N/A
2 year
1 year
6 mo.
YES
YES
CH9540H
N/A
2 year
1 year
6 mo.
YES
YES
CHF9540H
N/A
2 year
1 year
6 mo.
YES
YES
CH911DH
1.1 L Kubota
2 year
1 year
6 mo.
YES
YES
CH922DH
2.2 L Kubota
2 year
1 year
6 mo.
YES
YES
WARRANTY COVERAGE
CURRENT MODELS
PRODUCT
2 of 2
DEBRIS LOADERS
MODEL
ENGINE
CONSUMER
COMM.
RENTAL
PARTS
LABOR
DL8390
390cc Honda GX
2 year
1 year
6 mo.
YES
YES
DL10570
570cc B&S
2 year
1 year
6 mo.
YES
YES
DL12653
653cc Subaru
2 year
1 year
6 mo.
YES
YES
DL12720
720cc Subaru
2 year
1 year
6 mo.
YES
YES
STUMP GRINDERS
MODEL
ENGINE
CONSUMER
COMM.
RENTAL
PARTS
LABOR
SG340
340cc Honda GXV
2 year
1 year
6 mo.
YES
YES
MODEL
ENGINE
CONSUMER
COMM.
RENTAL
PARTS
LABOR
190cc B&S
2 year
1 year
6 mo.
YES
YES
WHEELED VACUUMS
WV190
WV190S
NOTE: “Consumer” use means personal residential household use by the original retail customer. “Commercial" or "Rental” use means all
other uses, including commercial, income producing or rental. Once a unit has experienced commercial or rental use, it will thereafter be
considered as commercial or rental.
ENGINE WARRANTY: For Engine Warranty information or service needs regarding the engine of your machine, record the serial number of
the engine and refer to the Engine Owners Manual for terms and conditions of the manufacturer or see your nearest dealer.
011 + 1 + 701.282.5520
37
WARRANTY COVERAGE
NON-CURRENT PRODUCTION
PRODUCT
1 of 2
CHIPPER/SHREDDER
MODEL
ENGINE
CONSUMER
COMMERCIAL.
RENTAL
PARTS
LABOR
SC2206
190cc B&S
2 year
N/A
N/A
YES
YES
240cc Honda GX
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
(purchased on or before Dec. 31, 2008)
SC3240, SC3240T
240cc Honda GX
(purchased on or after Jan. 1, 2009)
270cc Honda GX
SC3270, SC3270T
270cc Honda GX
614cc Honda GX/20hp Kohler
SC5614
614cc Honda GX
670cc Honda GX
SC5670B
670cc Honda GX
CHIPPER ONLY
MODEL
ENGINE
CONSUMER
COMMERCIAL.
RENTAL
PARTS
LABOR
CH45342
342cc B&S
2 year
1 year
6 mo.
YES
YES
390cc Honda GX
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
N/A
2 year
1 year
6 mo.
YES
YES
614cc Honda GX
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
CH45390
390cc Honda GX
CH45540
CH4614
614cc Honda GX
CH4540
N/A
614cc Honda GX
CH6614
(20hp Kohler) (purchased on or before Dec. 31,
2008)
614cc Honda GX
38
WARRANTY COVERAGE
NON-CURRENT PRODUCTION
PRODUCT
2 of 2
CHIPPER (continued)
614cc Honda GX
CH6614H
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
993cc B&S Vanguard
2 year
1 year
6 mo.
YES
YES
670cc Honda GX
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
CONSUMER
COMMERCIAL.
RENTAL
PARTS
LABOR
2 year
1 year
6 mo.
YES
YES
2 year
1 year
6 mo.
YES
YES
(20hp Kohler) (purchased on or before Dec. 31,
2008)
614cc Honda GX
670cc Honda GX
CH6670H
670cc Honda GX
CH6993H
CH8670H
670cc Honda GX
CH123DH
3 L Kubota
DEBRIS LOADERS
MODEL
ENGINE
670cc Honda GX
DL12670
670cc Honda GX
WHEELED VACUUMS
MODEL
ENGINE
CONSUMER
COMMERCIAL.
RENTAL
PARTS
LABOR
WV179
179cc Kawasaki
2 year
1 year
6 mo.
YES
YES
WV179S
179cc Kawasaki
2 year
1 year
6 mo.
YES
YES
Depending on the global region in which the machine is sold, suffixs for all the models listed could include: , XF, XS, XN or S.
NOTE: “Consumer” use means personal residential household use by the original retail customer. “Commercial" or "Rental” use means all
other uses, including commercial, income producing or rental. Once a unit has experienced commercial or rental use, it will thereafter be
considered as commercial or rental.
ENGINE WARRANTY: For Engine Warranty information or service needs regarding the engine of your machine, record the serial number of
the engine and refer to the Engine Owners Manual for terms and conditions of the manufacturer or see your nearest dealer.
011 + 1 + 701.282.5520
39
BELT REFERENCE GUIDE
Part Number
12106
Description
Belt, 3V670 Kevlar
Models
Area Used
72085, 72285, 72385 (SN =>21300), 75011, 75111
Beater Bar
12119
Belt, 2RB65
73525
Drive
12273
Belt, 3B90 Banded
CH922DH (74950)
Drive
12317
Belt, 4L 53
73040, 73050, 73450, 74040, 74450, 74455, 74050, 74060, 74065, 75065, 76065
Drive
12365
Belt, 3VX530
73710, SG340 (73711)
Drive
12573
Belt, 3L x 52 Kevlar
73150, 73350, 73265, 73455, 75365
Drive
12660
Belt, 4L350
CH5540H (74554), 74624, 74520
16000
Belt, BX-65
70500
Drive
16043
Belt, 29”
CH6730H, CH6670H (76624) & CH6993H (76635)(SN>603143),
Pump
16043
Belt, 29”
SC3206 (70050) (SN>105334), SC3342 (75311) (Single Belt Drive SN<C03478),
SC3305 (70080), SC3270E (70085), SC3240 (78380), 70180
Drive
16081
Belt, 27”
SC3206 (70050) (SN<105334)
Drive
16086
Belt, BX-49
70487
Drive
16347
Belt, 2B70 Banded
SC5614 (71020), 73413, 73420, 74520, 73120, 73125, 73725, 71014,
DL12670 (75124), DL12720
Drive
16500
Belt, VGates 6958
71110, 71125
Drive
16559
Belt, 3B83 Banded
CH8720iH, CH6614 (71620), CH6614H (72620), CH911DH (72928),
CH8670H (76824), CH8993H (76835), 71825, 72825, 74824,
Drive
16636
Belt, BX-43
CH9540H (72854), CHF9540H (76854)
Hyd Feed
16660
Belt, BX-38
CH911DH (72928) & CH922DH (74950)(VIN<5VJAA00118W000989),
CH6614 (72620), 72825, 74824, 72942,
Hyd Feed
16691
Belt, 3VX500
71755
Hyd Feed
Drive
16787
Belt, 3B85 Banded
72942
Drive
16799
Belt, 2R3VX475 EL COG
71785
Drive
16911
Belt, 3V560
72085, 72285, 72385, 75011, 75111
16912
Belt, 3V600
72085, 72285, 72385 (SN<21300)
17055
Belt, BX-56 [Qty 2]
SC5540B (73454), CH5540H (74554), CH5540, 70520
Drive
17558
Belt, 4L-38
70251, 70252
Drive
Belts, 29” (Matched set)
SC3265, SC3240 (70380), SC3240T (70580), 70385,
SC3342 (Dual Belt Drive SN=>C03478)
13426-00
Belt, 2RBP56
SC5540B (73554)
Drive
13884-00
Belt, SP BEARVAC (3L32)
WV190S (75360)
Drive
13973-00
Belt, 2RB63 Banded
SC5670B (75524)
Drive
17996
Drive
Beater Bar
Dual Belt Drive
14261-00
Belt, 3RB48 Banded
CH6730H, CH6993H (76635), CH611DH (76628), CH6670H (76624), 74628, 74624,
Drive
14770-00
Belt, 2RB61
CH4400, CH45342 (77412), CH45390 (77413)
Drive
14804-00
Belt, 5-5V750, Non Cog
CH123DH (7812086)
Drive
18093-00
Belt, 2RB47 [Qty 2]
CH45540 (77454)
18277-00
BX44 Belt
CH8720iH, CH8670H (76824), CH8993H (76835)
Hydraulic
Drive
18531-00
BX30 Belt
CH911DH, CH922DH (VIN>5VJAA00178W001015)
Hydraulic
18633-00
BX33 Belt
CH611DH (76628)
Hydraulic
31460-00
Belt, 2BRP67
CH5653
Drive
31498-00
Belt, 2RB40
SC5720B
Drive
32252-00
Belt, 3RB64
CH8540 (71854), CH9540H (72854), CHF9540H (76854)
Drive
40
ROTOR & CHIPPER/SHREDDER KITS
SHREDDER KNIVES REPLACEMENT KITS
All Kits contain knives, spacers, shafts, hardware and installation instructions
Part Number
Description
Models
70316
Kit, Shredder Knives
70530, 70515, 70525
70972
SC5614 (71020), SC5670B (75524), SC5540B
(73554), 73525, 71014, 70520
70973
Kit, Shredder Knives (Wide body 3” SC models)
SC3265, SC3305 (70080), SC3240 (70380),
SC3270, SC3342 (75311), 70385, 70180
71381
Kit, Shredder Knives (Narrow body 3” SC models)
SC3206 (70050) - Serial # C03159 and below
75502-00
SC2206
77589-00
Kit, Shredder Knives (Narrow body 3” SC models)
SC3206 - Serial # C03478 and above
77613-00
SC5720B
77616-00
77618-00
Kit, Optional Additional Shredder Knives
SC2170
COMPLETE ROTOR REPLACEMENT ASSEMBLIES
Part Number
Description
Models
70062
Replacement Rotor Assembly, 8 HP machines
(SN 25659 and below) (Shredder kit not included)
SC3265, SC3305 (70080), SC3240 (70380),
SC3270, SC3342 (75311), 70385, 70180
70277
Replacement Rotor Assembly, 5 HP machines
SC3206 (70050)
70366
Replacement Rotor Assembly, 5” Chipper/Shredders
SC5540B (71020)
73371-00
Replacement Rotor Assembly, 5” Chipper/Shredders
SC5670B (75524), SC5540B (73554), 73525
74209-00
Rotor Replacement Assembly, 3” Chipper/Shredders
(Wide body models)
SC3265, SC3305 (70080), SC3240 (70380),
SC3270, SC3342 (75311), 70385, 70180
75399-00
Rotor Replacement Assembly
SC2206
77591-00
SC3206
77612-00
SC5720B
77615-00
SC2170
011 + 1 + 701.282.5520
41
BLADE KITS
KITS CONTAIN ALL NECESSARY BLADES AND HARDWARE 1 of 2
MODELS
SN RANGE
VIN RANGE
KIT P/N
DESCRIPTION
BLADE P/N
0 - Current
70317
Small Chipper Blade
Kit
70293
0 - 25658*
70205
Single Edge
Small Blade Kit
70155
70738
Tool Steel Blade Kit
70739
76295-00
Chipper Blade Kit
76112-00
72493
Chipper Blade Kit
70739
4cm & 8cm CHIPPER/SHREDDERS
70515, 70525, 70530
SC2170, SC2206, SC3206 (70050),
SC3265, SC3305 (70080), SC3305E
(70085), SC3270 (70380), SC3270T
(70580), SC3342 (75311), SC3240,
70385, 70030, 72085, 72285, 70180
25659 - Current
5VJAA00137W000009 Current
10cm & 13cm CHIPPERS
CH4400
CH5653, CH5540, CH4540 (73454),
CH5540H (74554), CH500H (74500),
73412
CH4614 (73420)
0 - Current
0 - Current
0 - 705078
5VJAA00197W000009 - Current
11cm CHIPPERS
CH45342 (77412), CH45540 (77454),
CH450H, CH45390 (77413)
0 - 902474
0 - 5VJAA00109W001849
74744-00
77412/13 Blade Kit
71122
902475 - Current
76295-00
4-1/2 Chipper Blade
Kit
76112-00
70453
Single Edge
Blade Kit
70155
72493
Chipper Blade Kit
70739
0 - 5VJAA00159W001743
74220-00
6 Inch Blade Kit
71122
76293-00
Chipper Blade Kit
76112-00
71426
8 Inch Chipper Blade
Kit
71122
13cm CHIPPER/SHREDDERS
0 - 26376*
SC5614 (71020), SC5540B (73554),
SC5670B (75524), SC5720B, 70500,
70520, 71014, 74520, 73525
26377 - Current
15cm CHIPPERS
CH6730H, CH6670H (76624), CH611DH
(76628), CH6993H (76635), 74624,
74628
CH6614 (71620),
CH6614H (72620)
42
0 - 704809
0 - 705118
BLADE KITS
KITS CONTAIN ALL NECESSARY BLADES AND HARDWARE 2 of 2
MODELS
SN RANGE
VIN RANGE
KIT P/N
DESCRIPTION
BLADE P/N
20cm CHIPPERS
CH8720iH, CH8993H (76835),
CH8670H (76824)
71426
8 Inch Chippe
Blade Kit
71122
76293-00
Chipper Blade Kit
76112-00
71426
8 Inch Chipper
Blade Kit
71122
0 - 901387
71426
Kit
71122
901388 - Current
76293-00
Chipper Blade Kit
76112-00
502304 - Current
74830-00
Blade Kit
70739
0 - 5VJAA00109W001785
71426
Kit
71122
76293-00
Chipper Blade Kit
76112-00
73900-00
12" Blade Kit
74320-00
0 - 704960
0 - 5VJAA00119W001755
904473 - Current
74824, CH800H (74800)
0 - 804669
20cm & 23cm PTO CHIPPERS
CH8540 (71854),
CH9540H (72854)
CHF9540H (76854)
23cm CHIPPERS
0 - 704696
CH911DH (72928),
CH922DH (74950)
30cm CHIPPERS
CH123DH (7812086)
500423 - Current
STUMPGRINDERS
SG340 (73711), 71755, 71785, 73710
0 - 805549
SG340
810639 - Current
73711 with 12-blade retrograde fit kit,
PN 76256-00
0 - Current
0 - Current
71445
4 Blade Stump Cutter
16687 & 16688
Kit
76292-00
12 Blade Cutter
Replacement Kit
76903-00
12 Blade Cutter Retro
Fit Kit (To change
from 4 blade to 12
blade system)
16687 (4) &
16688 (8)
16687 (4) &
16688 (8)
SG340
0 - Current
76906-00
12 Blade Cutter
Upgrade Kit (To
change from 6 bolt to
12 bolt system)
011 + 1 + 701.282.5520
43
ACCESSORIES
Blades and Knives Kits
44
Blade Kit, P/N: 70738
Models: SC2170, SC3206, SC3265, SC3305 & SC3342
Blade Kit, P/N: 76293-00
Models: CH611DH, CH6730H, CH8720iH, CH8993H,
CH911DH, CH922DH, CH8540, CH9540H & CHF9540
Blade Kit, P/N: 72493 Models: SC5720B, SC5540B,
CH5653, CH5540H & CH5540
Shredder Knives Kit
P/N: 70972. Models: SC5540B.
Blade Kit, P/N: 76295-00
Models: CH4400, CH45540 & CH450H
Shredder Knives Kit
P/N: 77616-00. Model: SC2170.
Additional 4 Knives Kit, P/N: 77618-00
ACCESSORIES
Blades and Knives Kits
3" SC Screens
See model page for specific corresponding part numbers.
Coarse Screen
Standard
Fine Screen
Medium Screen
Wet Debris Screen
Shredder Knives Kit
P/N: 77613-00. Model: SC5720B
SC2170 Screens
See model page for specific corresponding part numbers.
Wet
2.87cm
Standard
1.9cm Fine
Debris
Shredder Knives Kit
P/N: 77589-00. Model: SC3206
Shredder Knives Kit, P/N: 70973
Models: SC3265, SC3305 & SC3342
011 + 1 + 701.282.5520
45
ACCESSORIES
Blower Kit with 2-Blade Radial Fan, P/N: 70251
Models: SC3265, SC3305 & SC3342
All Weather Cover, P/N: 70093
Models: All 8cm (3") Chipper/Shredders
Debris Bag, P/N: 17854
Models: Any models that discharge to the ground
46
Two Wheel Tow Kit, P/N: 77000-00
Leaf Tamper, P/N: 70089
12 Tooth Cutter Replacement Kit P/N: 76292-00.
Model SG340
ACCESSORIES
Optional 10cm x 10cm Discharge Chute, P/N: 74634-00.
Models: CH4400 & CH45540.
Low Profile Discharge, P/N: 74581-00.
Models: CH8540, CH8720iH, CH8993H, CH911DH,
CH922DH, CH9540H & CHF9540H.
Hour Meter Kit - Diesel P/N: 71921.
Models: CH611DH, CH911DH & CH922DH.
Adjustable Feed Speed Kit, P/N: 76820-00.
Models: CH611DH & CH6730H.
Hour/Tach Kit - Gas, P/N: 31605-00
Models: All gasoline engine powered machines
011 + 1 + 701.282.5520
47
ACCESSORIES
Vacuum Hose Kit
P/N: 73606-00. Models: WV190 & WV190S
Debris Bag
P/N: 31339-00. Models: WV190 & WV190S
Caster Wheel Kit
P/N: 76967-00. Models: WV190 & WV190S
Swing Away Hitch Mount Kit
P/N: 75739-00. Models: DL8390 & DL10570
Nozzle Wear Plate
P/N: 73640-00. Models: WV190 & WV190S
Vacuum Liner
P/N: 76466-00. Models: WV190 & WV190S
48
Tailgate Adapter Kit
P/N: 75753-00. Models: DL8390 & DL10570
ACCESSORIES
1.2m (4') Flexible Chute Extension
P/N: 74737-00. Models: All Debris Loaders
Debris Loader Light Kit
P/N: 77105-00. Models: DL12653 & DL12720
Wear Liner Replacement Kit
P/N: 75768-00. Models: DL8390 & DL10570
41cm (16") Vertical Chute Extension, P/N: 75888-00
Models DL8390, DL10570, DL12653 & DL12720
To view a complete list of
ECHO Bear Cat parts and
accessory options,
please visit our website
Wear Liner Replacement Kit
P/N: 77073-00. Models: DL12653 & DL12720
011 + 1 + 701.282.5520
and click on
Options and Accessories under the Products tab.
49
NOTES
50
NOTES
011 + 1 + 701.282.5520
51
ECHO Bear Cat • 237 12th St. NW, West Fargo, ND 58078
For customer service or for your nearest ECHO Bear Cat dealer call 888.625.4520
For International call 011 + 1 + 701.282.5520
Specifications, descriptions and illustrative material in this literature is as accurate as
known at the time of publication, but are subject to change without notice. Illustrations may
include optional equipment and accessories and may not include all standard equipment
©2014 ECHO Bear Cat, a subsidiary of ECHO Incorporated
All Rights Reserved. Printed in the USA
Updated 11/2013

chipper/shredders - Dorian Drake International Inc.

Transcription

Similar documents

CHIPPERS CHIPPER/SHREDDERS

Where you come to know.

Boneng Gearboxes

MORBARK® 40/36 NCL WHOLE TREE CHIPPER

The 7272 is a heavy-duty shear type shredder. The elements that

model 1390xp

chipper shredder

30/36 NCL Whole Tree Chipper Spec Sheet PDF

- Brooks Construction