SYNCRO AS-2M4 Brochure

Transcription

WWW.INCITEFIRE.COM.AU
SYNCRO AS 1-2 LOOP SYSTEMS
Syncro AS
Key Features
Analogue Addressable
Fire Control Panels
(1 or 2 Loops)
* The Syncro has wireless options
* The Syncro can be networked - why have one large panel ?
Did you know ?
* The multisensor can operate as 2 detectors : smoke local and heat all.
* The sounder base has 51 tones and 8 can be operated from the panel Why use OWS?
* There is a modem for remote access to the Syncro
Standard Features
Product Overview
• Approved to AS7240.2 and AS7240.4
The Syncro AS addressable control panel
is designed to meet the requirements of
AS7240.2, AS7240.4
• Available in 1 or 2 loops and
networkable up to 64 panels with up
to 500 zones per network (the perfect
solution for small and large solutions)
Available in 1 or 2 loops and networkable up to
64 panels with up to 500 zones per network
(the perfect solution for small and large
projects)
• 127 devices per loop / Up to 800 sub
addressable
The Syncro AS is capable of driving a full loop of
sounders @ 85dB
• LCD display & 16 zone LED indication
• Compatible with Hochiki ESP detectors
and modules
• Open protocol, non-proprietary
software
• ActivFire listed AFP-2761
• System enabled with 003 key
Housed in the same installer friendly and
attractively styled enclosure as the Sigma CP
(conventional) and Sigma XT (extinguishant)
range of control panels, the Syncro AS
combines compact and practical styling with
the programming power and connectivity
normally associated with much larger systems
• Optional OWS available - 20,40,60,120
• Optional fan control available
• Capable of driving a high number of
loop powered sounders
• Base cabinet size 385W x 520H x 110D
(mm)
• Range of cabinet sizes available
Other Features
* Standard or Deep cabinet options
Config Features
* Comprehensive day/night mode facility
* Programmable one touch test mode
* Powerful and versatile cause & effect
programming
* Cause and effect wizard including:
* Cause and effect action
* Disablement configuration
* Test mode configuration
• 16 zonal LED indicators
• 5 preconfigured digital inputs
• Easily configured using Loop Explorer
software
• Up to 32 RS485 expansion modules
per panel
42
QLD 07 3252 5366 NSW 02 9644 7144
New Features
* Hotel Mode
* AAF
* Non latching detectors
* Non fire attributes: Detector options for
system control only
VIC 03 9544 2211
SYNCRO AS 1-2 LOOP SYSTEMS
Technical Specifications
Overall size (std)
385W x 520H x 110D (mm)
FinishEpoxy powder coated
Colour - lid & box
BS 00 A 05 grey - fine texture
Colour - controls plate & labels
RAL 7047 light grey - satin
Supply voltage
230V AC +10%/-15% (100 Watts maximum)
Mains supply fuse
1.6 Amp (F1.6A L250V
Operating voltage
18 to 30 volts DC
Battery charging circuit impedance Rimax
1.35R
Min ouput current for correct operation Imin 130mA
Max ripple current
1.5 +/- 0.3V
Battery typesealed lead acid
Aux 24V output rating
300mA maximum load (fused at 500mA)
Sounder output rating (2 outputs)
Each rated at 1A
Relay contacts30VDC, 1A maximum
Fault contact rating
Local fire contact rating
Fire contact rating
30V DC 1 Amp
30V DC 1 Amp
30V DC 1 Amp
Panels
SYNCRO AS-1M3
Syncro AS 1 Loop in M3 Cabinet (385W x 520H x 110D)
SYNCRO AS-1M3TD
SYNCRO AS-1M4TD
SYNCRO AS-2M3TD
SYNCRO AS-2M4TD
Cabinet Options
M3 Cabinet
• 385W x 520H x 110D (mm)
• 2 viewing / control apertures
• Lockable window door available
M3D Cabinet
• 385W x 520H x 200D (mm)
M4 Cabinet
• 385W x 700H x 200D (mm)
Flush surround available for all cabinets
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
43
METALWORK OPTIONS
Metalwork Options For Sigma and Syncro
Systems
Product Overview
All the metalwork options available are designed to match and complement the complete range of SigmaCP, SigmaXT & SyncroAS
control panels.
The 19” rack mount is particularly ideal for use in a combined FIP / QE90 EWIS panel or when fitting in IP rated enclosure. It houses and
supports the entire FIP on a fully hinged swingout frame constructed of welded steel for strength and powder coated to match the
fitted panel.
The flush surrounds are available for all cabinet sizes and warning signs. They are designed to complement the look of the entire range
of cabinets. All the flush surrounds are easy to install, are constructed of welded steel and powder coated to match the fitted panels.
The ASE brackets are custom made for ROMTEK & CENTAUR alarm signalling equipment. They are finished in light grey satin, to match
the entire range Sigma and Syncro panels.
KM - FS-M2
Flush Sourround
M2 Flush Surround
• 415W x 340H x 15D (mm)
• Cutout - 385W x 310H (mm)
• Fascia width - 15mm
KM - FS-M3
M3 Flush Surround
• 415W x 550H x 15D (mm)
KM - FS-M4
M4 Flush Surround
• 415W x 730H x 15D (mm)
KM - FS-WS
44
QLD 07 3252 5366 NSW 02 9644 7144
Flush surround also available for warning signs
VIC 03 9544 2211
METALWORK OPTIONS
19’’ Rack Mount
• Available for M2 and M3 size cabinets
• Houses the complete panel for rack mounting
• Fully hinged to swing out complete panel
• Robust fully welded steel construction
• Epoxy powder coated to match panel coulour
• Ideal for QE90 combination panel
* Mounting information into 19” IP rated enclosure
KM -HS-M2-9RU M2
M2 19” Hinged sourround
KM-HS-M3-13RU M3
M3 19” Hinged sourround
ASE Brackets
• Available for ROMTEK and CENTAUR
• Light grey satin finish to suit other modules
• Fits neatly into viewing aperture
KM -ASE-RT
• Suitable for use in M3 and M4 size cabinets
• Mounts ASE to be flush
KM -ASE-CT
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
45
SYNCRO CABINET OPTIONS
Cabinet Options
Product Overview
Constructed of 1.2mm sheet steel and finished with light grey epoxy powder coating, our range of cabinets are designed to be
aesthetically pleasing and functional.
The viewing or control apertures provide a fully modular system for fitting of equipment such as manual call point, fan controls, OWS
controls, ASE and other equipment.
An ample number of knockouts for cable entry are provided on the rear, top and sides of the cabinets, and their lightweight
construction makes installation easy.
Lockable window doors are available for the M3 & M4 size cabinets, providing an extra level of protection against tampering.
Flush surrounds are available for all 3 cabinet sizes & hinged 19” rack mounts are available for the M2 & M3 cabinets
Range
M2 Cabinet
• 385W x 310H x 90D (mm)
• 1 viewing / control aperture
• Also available in M2D - 110mm deep
M3 Cabinet
• 385W x 520H x 110D (mm)
• Also available in M3D - 200mm deep
M4 Cabinet
• 385W x 700H x 200D (mm)
• Fault indicator - Yellow LED
* Flush surround available for all cabinets
Construction1.2mm mild sheet steel
Colour - lid & box
IP rating30
Locks
1 lock on M2, 2 locks on M3 & M4
Keyed003
46
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
SYNCRO CABINET OPTIONS
Industrial Cabinet
Features
Standard Cabinet
• Various sizes available to suit application
• 1.6mm thick zinc coated steel
• Powdercoated finish
• Polycarbonate viewing window
• Protection rating IP 66
Stainless Steel Cabinet
• Various sizes available to suit application
• 1.6mm thick 316 stainless steel
• Polycarbonate viewing window
• Protection rating IP 66
* Optional 003 keyed lock for any cabinet
* 3 point locking on larger cabinets
* Polyurethane gasket foamed in place
* Guttered door opening
Construction (standard)
1.6mm Zinc coated steel (corrosion resistant)
Finish (standard)
Epoxy powder coated - RAL7032
Construction (s/steel)
316 Stainless steel
Finish (s/steel)
N4 surface finish (eliminates ‘tea staining’)
LockSquare key multi point locking mechanism
KeyedOptional 003 keyed lock
GasketFixed polyurethane gasket
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
47
OCCUPANT WARNING CONTROL
& FAN CONTROLS
Occupant Warning Control
Product Overview
The Incite occupant warning system control module has been designed
to enable an easy interface of the Sigma and Syncro fire control panels to
Evactron or Tgen amplifiers, and to provide paging and manual control
facilities.
The module is supplied on a carrier plate suitable for ease of fitting
neatly into a Sigma or Syncro control panel. The SOWC is secured from
unauthorised operation via a 003 keyswitch. It has test and PA buttons, alarm
and fault LED’s, and an inbuilt microphone.
Features
• Fits the standard Syncro AS & Sigma cabinet carrier plate
• Secure access to the control via standard 003 Key switch
• Alarm and Fault indicators
• High quality Inbuilt panel microphone
EVAC-SD-OWC
• Compatible with Evactron 20,40,60,120 OWS AMPS
• Compatible with Tyco TGEN50 OWS AMPS
• Quick and easy to fit
Fan Control Module
Product Overview
The Incite SyncroAS fan control module (SFCM) has been designed to
enable ease of interface to building services providing smoke control in an
installation.
The SFCM manual controls will only operate when the enable keyswitch on
the SyncroAS panel is in the enable position.
The SCFM contains 3 off 1668 control and status indicators, a general fire trip
and isolate, and a lamp test button. The module connects to the SyncroAS
panel by four wires, two for power and two for RS485 communications.
Features
• Contains 3 x AS1668 controls
• Connects directly to SyncroAS RS485 data bus
• Auto - fan on and fan off modes
SYNCRO-KAU2016
• Configurable through SyncroAS control panel or via a PC with Loop Explorer
software
• Provides seamless fan control integration with SyncroAS panels
• Interfaces SyncroAS control panel to the duct detectors
ANC Control
Features
• Enables ease of interfacing to building services providing mual control &
indication in an installation
• Controls enabled by the keyswitch on the Syncro AS panel
• 4 push button controls, 8 LED indicators & 3 clean contact relays
• Simple 4 wire connection to the Syncro AS panel, 2 for power, 2 for RS485
SYNCRO-K556
48
• the ANC control may be mixed on the RS485 bus with other
expansion/control devices
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
DOCBOXES
DocBox
Product Overview
Another addition to the range, the document box is designed to
complement the design and colour of the Sigma and Syncro range
of control panels. The document box will hold up to 100 sheets of A4
documents or log books.
The “DocBox” also doubles up as a key box providing 7 (M2) or 14
(M3) easily accessible key hooks inside the enclosure.
Features
• Matches design and colour scheme for standard Sigma and
Syncro control panel range
• Easy to install
• Key lockable
• Designed for versatility
• Holds A4 size documents and Log books
• The document box also doubles as a key box providing 7 (M2) or
14 (M3) easily accessible key hooks inside
Sigma-M2-DocBox
Sigma-M2-DocBox
Sigma-M3-DocBox
Size
(M2) 385W x 310H x 90D (mm)
(M3) 385W x 520H x 110D (mm)
Construction 1.2. mild steel sheet
Colour BS 00 A 05 grey - fine texture
Weight 3Kg
Lock type 003
Document space A4 (M2) A3 (M3)
No of key spaces 7 (M2) and 14 (M3)
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
49
SYNCRO IO
Syncro IO
16 channel input /output board
Syncro-K560
Product Overview
Standard Features
To add more I/O capability to the extensive options already
offered by the Syncro control panel, up to thirty two, 16 channel
I/O boards may be connected.
* 16 channels
The 16 channel boards may be mixed on the RS485 bus
with 8 way sounder boards, 6 way sounder boards or 4 way
conventional detection zone boards to provide a very flexible
system of I/O to satisfy any requirement.
* Each channel configurable as input or output
* Inputs opto-isolated
* Outputs open collector transistor
* Simple 2 wire connection to control panel Up to 32
boards supported per panel
When using a simple two wire RS485 communications protocol,
these boards may be mounted locally to the control panel or
distributed on a bus up to 1200 metres long by using a suitable
cable.
* (512 Input/Output Channels)
The flexibility of these boards is further enhanced by the fact
that each of the channels is configurable as either an input or
an output.
* Multi drop RS485 communications can be used with
other Syncro I/O modules on the same panel
* Inputs and outputs configurable as per field devices
* Full cause and effects on all inputs and outputs
* Compatible with Syncro AS panels
Each channel may also be configured to produce a variety of
input actions or respond to a variety of output types.
All channels can contribute to, or respond to, system wide cause
and effects logic.
Typical uses for I/O boards include geographical LED mimic
displays and plant alarm inputs.
Standard Syncro control panels contain fixings for one sounder,
relay, conventional detection or I/O board, which can easily
be connected using four small signal wires to the power and
comms bus within the panel.
Consideration must be taken as to the loading on the main
panel.
50
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
SYNCRO IO
Product codeSYNCRO-K560
Supply voltage
21 - 30V DC
Quiescent current consumption
20mA
Weight1kg
Current per input3mA (maximum)
Current per output100mA (maximum)
CommunicationsRS485 two wire
Maximum distance from panel
1.2Km (using correct type of cable)
PCB size190mm x 61mm
Cable capacity2.5mm per terminal
Operating temperature
-10°C to +50°C
Operating humidity
To 95% (non condensing)
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
51
SYNCRO IO
Syncro IO
4 way conventional
Detection Zone
Module
Syncro-K545
Product Overview
Standard Features
To further enhance the versatility of the Syncro fire alarm system,
four conventional detection circuits can be connected with up to 30
detectors per circuit.
* 4 monitored detection zone inputs
Conventional control panels can be replaced with this simple
module and existing conventional systems can be interfaced
directly to modern analogue addressable control systems and
networks.
A fail safe mode ensures that the detection inputs will still operate
the sounder outputs and fire contact if communication to the
Syncro panel is lost.
* 2 monitored sounder outputs
* Volt free fire contact
* Local power supply fault input
* RS485 comms connection to Syncro Fire Alarm Panel
* Individual fault and operated indications for inputs and
outputs
* Directly replaces a conventional control panel when
integrating into an analogue addressable system
Up to 32 of these boards can be connected to the dedicated RS485
communications bus in the control panel giving the capability of up
to 128 conventional zones with 64 sounder outputs.
* Can be used with other Syncro I/O modules on the same
panel
The detection zone boards may be mixed on the RS485 bus with 16
channel I/O Boards, 6 way sounder boards or 8 way relay boards to
provide a very flexible system of I/O to satisfy any requirement.
* Compatible with Hochiki range of detectors. For any
other brands please contact Incite Fire.
* Compatible with Syncro AS panels
All inputs and outputs are configurable in the same way as devices
connected to the loops and all may be acted upon by cause and
effect logic.
Standard Syncro control panels contain fixings for one (four way)
Detection Zone board, Sounder board, Relay board or I/O board,
all of which can easily be connected using four signal wires to the
power and comms bus within the panel.
Consideration must be taken as to the loading on the main panel.
52
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
SYNCRO IO
Supply voltage range
21 to 30 volts DC
Quiescent current consumption
70mA
Weight1kg
Operating current (all outputs on)
250mA
Output contact rating
30V DC 1 Amp
Detection zone monitoring resistor
6k8
Sounder circuit monitoring resistor
10k
CommunicationsRS485 two wire
Max. distance from panel
1.2Km (using RS485 data cable)
PCB size190mm x 74mm
Fixing centres51.5mm x 180mm
Cable capacity2.5mm per terminal
-5°C to +50°C
Operating humidity
To 95% (non condensing)
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
53
PSU - SWITCH MODULE POWER
SUPPLY/CHARGER
PSU
Approved Switch Mode Power Supply/Charger
PS-406 (5 AMP)
PS-408 (10 AMP)
Product Overview
PS-408 Standard Features
The PS407-PS408 power supply/battery charger has been developed using
switched mode technology to produce an efficient and lightweight power unit
for a host of fire alarm applications.
* Complies with AS7240-4
Suited to almost any application, the PS407-PS408 is designed to be a universal
power source which will reduce spares stock holding and increase serviceability
of systems.
The comprehensive monitoring features of the PS407-PS408 include true
battery present detection, low battery voltage warning, battery overcharge
warning, high battery impedance monitoring and low battery shut off.
These features combined with the temperature compensated charger output
will increase the service life of sealed lead acid batteries.
* Fully enclosed construction
* Small and lightweight
* True 10 Amp continuous output
* Comprehensive fault monitoring
* Temperature compensated charger
* Wide input supply voltage
* Low battery shut off to prevent deep discharge of
battery
PS-406 Standard Features
* Complies with AS7240-4
* Fully enclosed construction
* Small and lightweight
* True 5 Amp continuous output
* Comprehensive fault monitoring
* Microprocessor controlled
* Temperature compensated charger
* Wide input supply voltage
* Low battery shut off
54
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
PSU - SWITCH MODULE POWER
SUPPLY/CHARGER
Technical PS-408
(10 Amp)
Construction
Finish
Epoxy powder coated
Colour
Black
Size
260mm x 120mm x 65mm
Weight
2Kg
Supply voltage
230V AC (+10%/-15%)
Output voltage
24V DC
Total output current
10.25 A
Battery charge current
2.25 A
Load Current
8.0A (with flat battery)
Fault outputs rating
50mA max.
Mains fuse
5 Amp 20mm HRC
Load fuses
10 Amp (self resetting)
Mains failed warning
Switched -ve output
Battery disconnected warning
Switched -ve output
Battery low warning
Switched -ve output
Battery overcharge warning
Switched -ve output
Earth fault warning
Switched -ve output
Common fault output
Switched -ve output
-5 to +50 deg. C
Technical PS-406
(5.25 Amp)
Construction
Aluminium base - sheet steel cover
Finish
Epoxy powder coated
Colour
Black
Size
226mm x 120mm x 55mm
Weight
0.9Kg
Supply voltage
230V AC (+10%/-15%)
Output voltage
24V DC
Total output current
5 Amps (continuous)
1.25 Amps max.
Load current
4.0 Amps (with flat battery)
Fault outputs rating
50mA max.
Mains fuse
3 Amp 20mm HRC
Load fuses
5 Amp (self resetting)
Mains failed warning
Switched -ve output
Battery disconnected warning
Switched -ve output
Battery low warning
Switched -ve output
Battery overcharge warning
Switched -ve output
Earth fault warning
Switched -ve output
Common fault output
Switched -ve output
-5 to +50 deg. C
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
55
PSU - FIRE POWER SUPPLIES
PSU
Approved Fire Alarm Power Supplies
PS 407-M2D
ActivFire #: AFP 2793
PS 406-M3
Product Sizes
PS407
= PSU S407 - 24V - 2.5Amp Power Supply
PS407-M2D= 24V-2.5A PSU CABINET, UP TO 12AH (385W X 310H X 110D)
PS407
PSU-S407
= PSU S406 - 24V - 5.25Amp Power Supply
PS406-M3 = 24V-5.25A PSU CABINET, UP TO 22AH (385W X 520H X 110D)
PS408 = PSU S408-24V@10 Amp Powersupply
Product Overview
Power supplies provide a stable and fully regulated, true 24V output for fire
alarm system applications under all power conditions.
The unique regulation techniques ensure that even when running on standby
batteries, a stable 24V supply is available to all parts of the system ensuring that
all 24V powered devices connected are supplied with optimum power.
The powerful onboard micocontroller ensures that all battery types are
conditioned with optimum, temperature compensated charging algorythms to
maximise battery life and maintain batteries in top condition.
Standard Features
* 2.5A, 5.25A and 10A versions
* Chassis only or enclosure mounted with battery
space
* 110V or 240V input
* Regulated, true 24V output
* Intelligent battery charging and temperature
compensation
* House up to 26Ah batteries
* Status indicators for monitored faults
Enclosed units are available to match both Sigma and Syncro equipment ranges
and all are finished with matching livery and provide power on and power fault
indications.
* Dual output option for powering fire alarm control
panels remotely
* Chassis versions have same mounting points
* Fully enclosed and robust construction
* Approved to A7240-4
56
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
PSU - FIRE POWER SUPPLIES
Construction
1.2 mild sheet steel
IP Rating
IP30
Finish
Epoxy powder coated
Colour - lid & box
Mains input supply voltage
240V AC 50/60Hz or 110V AC 50/60Hz (link selectable)
Mains supply fuse
250V, 3A, SB, 5mm X 20mm
Load output voltage
19- 30V DC +/- 1%
Maximum ripple
1 Volt
Load fuse
5 Amp, self resetting Polyfuse
Maximum current draw
5 Amps
from batteries
Battery charge output voltage
27.4V DC nominal at 20 degrees C
(temperature compensated from -5 to 45 degrees C
Two stage, constant voltage. 1.25 Amps maximum
Deep discharge prevention
Battery disconnects at 19V
-5 to 45 degrees C
Common fault output
Normally energised volt free changeover relay – 30V DC 1 Amp
Battery disconnected output
Open collector 50 milliamps
Battery low output
Charger fault output
Earth fault output
Mains failed output
Fault output connector
14 way DIL header 0.1” spacing
Mains connector
3 way terminal, 7.62mm spacing, 2.5mm maximum cable size
Load connector
Battery connector
Front panel Power On indicator
Green LED
Front panel Fault indicator
Yellow LED
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
57
Syncro AS
Analogue Addressable
Fire Control Panels
Networkable
SYNCRO AS LARGE SYSTEMS
For large projects there is the option of
networking Syncros in one enclosure to
provide addressable loops.
Networking
The flexibility of the SyncroAS system can be further enhanced by connecting up to 64 control panels together on a high integrity network. A
simple two wire connection between each panel allows events to be transmitted to other parts of the system to provide indication or control on
a system wide basis.
Using the Loop Explorer configuration software, up to 64 nodes can be programmed to respond in a variety of ways to any system events as
required.
This flexibility extends the comprehensive cause and effect programming capability of SyncroAS panels to the entire network allowing actions,
test modes or disablements to be started from any point.
The fault tolerance of the network is such that any single open or short circuit fault will not result in any loss of information. Multiple faults are
isolated and the network breaks into smaller networks which continue to work autonomously.
Each SyncroAS on the network also provides a RS485 data bus which can accomodate up to 32 field devices such as SyncroVIEW repeaters,
SyncroMATRIX mimic displays and ancillary PCB’s. The maximum number of SyncroVIEW or Syncro MATRIX is limited to 15 per RS485 data bus.
Networking Features
• High integrity protocol
• Up to 1,000 mtrs (1Km) between panels
• 1 or 2 loops per panel, each loop capable of up to 127 Hochiki devices / 800 sub addressable
• Colour graphics interface
• Up to 32 field modules per panel on a RS485 data bus
• Repeaters & Mimic panels on RS485 data bus
• Fully secure against short or open circuit faults
• Network wide test and disablement functions
• Network wide cause and effect logic
58
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
SYNCRO AS LARGE SYSTEMS
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
59
SYNCRO REPEATER
Syncro View
Local LCD Control Panel
Repeater
Product Overview
Designed and manufactured to the highest standards in a quality
controlled environment the Syncro VIEW fire alarm annunciator
provides a simple and convenient method of extending the controls
and indications of the Syncro fire alarm control panel to other
locations.
The large, graphic liquid crystal display and high brightness LED
indicators duplicate the indications on the Syncro fire alarm control
panel at up to 15 additional locations via a simple, two-wire serial
data connection.
The Syncro VIEW is available in either a 24V DC powered option
(which can be powered via an additional 2 cores from the Syncro
control panel/local 24V DC supply) or a 230V powered option with
local battery back up.
Syncro View
Standard Features
Syncro VIEW is housed in a small enclosure which is styled similarly
to the Syncro control panel and is ideal for installations where a large
control panel would be detrimental to décor such as entrance halls.
Up to 15 Syncro VIEW annunciators can be connected to each control
panel on the Syncro network making VIEW ideal where multiple
points of indication and/or control are required such as nurses
stations or shop units.
* Up to 15 annunciators can be connected to each Syncro,
Response or Syncro AS fire control panel.
* Large liquid crystal display (240 x 64 pixels)
* High brightness LED indications
* Internal sounder
* Replicates all Syncro panel controls
* Simple, two-wire serial connection
* Small, Syncro style enclosure
* Removable electronics for easy installation
* 24V DC or 230V AC power options
* Low power consumption
* Multi language options
* Connection monitored by Syncro fire
control panel
60
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
SYNCRO REPEATER
Construction
1.2mm mild sheet steel
IP RatingIP30
Colour - lid and box
Ral 7047 light grey - satin
Weight4kg (standard panel)
Display
8 lines of 40 characters graphic LCD
Cable entry
5 x 20mm knockouts in top of box and 5 in rear
Mains supply (Mains models only)
230V AC +10% - 15% (20 Watts maximum)
24V supply (24V DC models only)
21 to 30V DC
Mains supply fuse
2 Amp, 20mm
Power supply rating
28V 750mA total (including battery charging)
Maximum ripple current
200 millivolts
Battery type (Yuasa NP)
Two 12 Volt 1.9Ah sealed lead acid in series
Battery charge voltage
27.6VDC nominal
200mA maximum
Battery fuse
200mA, 20mm, glass
Maximum current draw from batteries
95mA
Quiescent current of panel in mains fail
0.03 Amps
Serial data connection
2 core RS485 (Up to 1200 metres total cable length)
Maximum terminal capacity
2.5mm²
Ordering
Syncro View Syncro View repeater panel
255H x 330W x 90D
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
61
SYNCRO LED INDICATION PANEL
Syncro
Product Overview
Programable LED Indication
Syncro Ident panels provide a compact and attractive display for up
to 24 indications from a Syncro or Syncro AS fire control panel.
Panels
As with all inputs and outputs on the Syncro system, each indicator
is fully programmable to indicate a variety of events as well as being
fully programmable via cause and effects to operate in response to
logically connected inputs. Each indication defaults to a zonal fire
indicator but may be configured via the Loop Explorer configuration
utility to operate upon any event type or combination of inputs.
Requiring only a low current 24V power supply and a 2 core data
connection to the fire panel, Syncro Ident panels can be installed
quickly and easily to provide supplementary information on the
status of the fire alarm system with the minimum of cost and effort.
The compact, slimline enclosure is unobtrusive and is ideal for
mounting in locations where a larger control and indication unit
would be unsuitable.
Syncro Ident
Each indication has a dedicated field for customised text to provide
a concise description of the indication. Multiple Syncro Ident panels
can be connected to the Syncro serial bus to provide a diverse range
of indications at multiple locations.
Standard Features
* 8 and 24 LED versions available as standard
* Large versions available to special order
* Up to 16 x 24 way Syncro Ident can be
connected to each fire panel
* Programmable flashing or steady states
* Red, yellow or green indications/ options
* Common Fire, Fault and Disabled
indication
* Customisable label identification tags
* Buzzer with silence control and re-sound
* Lamp test control
* Low power 24V DC supply
* Connects to 2 wire Syncro RS485
62
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
SYNCRO LED INDICATION PANEL
Construction
1.2mm mild sheet steel
IP RatingIP30
Colour - lid & box
Weight4kg
LED colours
Red, yellow or green
Supply Voltage
18 to 30V DC
Data Connection
RS485 Syncro comms bus (Max 1200 metres)
Indicator Status
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
63
SYNCRO MATRIX
Syncro Matrix
Intelligent Fire Alarm
Mimic Display System
Product Overview
The Syncro Matrix system uses flexible, fibre optic light guides to
illuminate areas on a floor plan, laid over a high resolution grid.
This unique system dispenses completely with wiring and enables
indicators to be moved, removed or added on site without the need
for any wiring.
All indicators can be configured to operate upon any event type and
at point, zone or group level via Kentec’s powerful and intuitive Loop
Explorer configuration programme. Syncro Matrix can be supplied
with or without LEDs and controls. Optional LEDs indicate Power
on, Fire, Fault and Disablement and optional controls are for Alarm
silence, Buzzer silence, Lamp test and Reset.
Product Sizes
Housed in attractive, slimline enclosures to match Syncro and Syncro
AS fire alarm panels and with high quality, full colour or monochrome
floor plans, Syncro Matrix provides a clear, geographical indication of
fire alarm activation enabling speedy identification of the source of
an alarm.
Syncro Matrix-CP-M2
Matrix CP Mimic panel in M2 cabinet ( Max 24 zones)
Syncro Matrix-CP-M3
Matrix CP Mimic panel in M3 cabinet ( Max 56 zones)
Syncro Matrix-CP-S4
Matrix CP Mimic panel in S cabinet ( Max 88 zones)
Standard Features
* Up to 504 LED’s can be controlled from any Syncro or Syncro
AS panel
* Full colour printing
* Available in a range of standard enclosures to suit any
applications
* Bespoke sized units can be made upon request
* Choice of Red, Green or Yellow LED’s
* Available with or without controls
* Same look and feel as Syncro range
* Syncro Matrix can easily be upgraded on site with minimal cost
and effort
* Configured via standard Loop Explorer Software
64
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
SYNCRO MATRIX
Construction
IP Rating
Finish
Colour - lid & box
Mimic
Number of indicators (standard models)
Mains supply*
Mains supply fuse*
1.2mm mild steel
IP30
Epoxy powder coated
3mm Clear Anti-Glare Acrylic
M2 size - up to 32, M3 and S3 size - up to 64, S4 size - up to 96
230V AC +10% - 15% (100 Watts max.)
T2A L250V Replace only with similar type
Power supply rating*
Maximum ripple current*
5.25 Amps total including battery charge 28V +/ 2V
200 millivolts
Battery charge voltage*
Battery charge current*
Max. current draw from batteries*
Supply voltage (24V versions)
Terminal capacity
Cabinet locks
Maximum distance from control panel
27.6VDC nominal (temperature compensated)
1.5A maximum
3 Amps. With mains power source disconnected
18 to 30V DC
0.5mm2 to 2.5mm2 solid or stranded wire
M2/M3 - standard 003 key, S3/S4 - standard 003 key
1km with 1.5mm2 cable
-5°C to +50°C
* When power supply fitted
Enclosure Size Options
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
65
SYNCRO NET
Syncro Net
Syncro Networking
Product Overview
The flexibility of the Syncro system can be further enhanced by
connecting control panels and repeaters together using a high integrity
network.
A simple 2-wire connection between each panel allows events to be
transmitted to other parts of the system to provide indication or control
on a system wide basis.
Using the Loop Explorer configuration programme, up to 64 nodes can
be programmed to respond in a variety of ways to any system events as
required.
Syncro-K555
This flexibility extends the comprehensive cause and effect programming
capability of Syncro control panels to the entire network allowing actions,
test modes or disablements to be started from any point.
The fault tolerance of the network is such that any single open or short
circuit fault will not result in any loss of information. Multiple faults are
isolated and the network breaks into smaller networks which continue to
work autonomously.
With regards to the design of fire systems for larger sites its widely
acknowledged globally that instead of producing ever larger loop
capacity panels a modular/networked peer-to-peer approach provides a
more evenly distributed system. Typically in the past a large system for a
10 storey building may have been designed with a single 10 loop panel.
This type of centralised system is far more susceptible to a single critical
fault like for instance a display board or maybe a motherboard failure,
indeed it could even a structural issue at the location of the FIP. This
could leave the whole system incapacitated for a duration of time until a
replacement or repair can be made. But the same site suffering the same
failures but instead installed with five 2 loop Syncro panels located evenly
throughout the 10 floors, would not only incorporate shorter loop cable
runs but would in this instance only result in the system either missing 1
of 5 displays or in the worst case scenario have a maximum of two loops
non functioning. But the Syncro network would largely remain functional
across the rest of the site due to its distributed design.
66
Standard Features
* Up to 64 nodes
* High integrity protocol
* Fully secure against short or open circuit faults
* Simple 2-wire loop connection
* Supports open ended networks for retrofit applications
* Repeaters share network connection
* Network wide test and disablement functions
* Network wide cause and effect logic
* Flexible configuration options
* Panels configurable to act on network events or not as
required
* Hochiki panels supported on single network
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
SYNCRO NET
ProtocolRS485
ConnectionTwo wire loop
Current Consumption40mA
Integrity
Full isolation of faulty nodes or wiring segments
Indicators
Data In and Data Out communications status
Cable length
200 metres to adjacent nodes
(subject to cable type) (see technical manual)
Cable type
Belden 9271, Belden 9860, FP200 Gold
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
67
SYNCRO GUIDE
Syncro Guide
Graphic User Interface for Fire
Detection Equipment
Product Overview
Syncro fire control panels can send data to, and be controlled
by, the Guide system providing a single point of co-ordination
for all alarms.
The powerful 32 bit programme features a standard Windows
look and feel and runs under Windows® 2000 , XP, Vista or
Windows 7 Professional.
The system is highly configurable in terms of the style of
presentation so that the end user can be presented with maps,
text, photographs, audio or a combination of all as required.
User profiles allow the system manager to control the facilities
available to each individual system user.
A comprehensive history logging and reporting system
allows analysis of events and trends to be identified to reduce
unwanted alarms.
Easy to programme and simple to use, Guide provides a cost
effective solution for fire alarm management at many levels.
Virtual window allows direct control
Standard Features
* Choice of text, graphic, event list display when an event
occurs
* Versatile event analysis
* Total history archive
* Easy to programme
Powerful event log filter
* Secure system
* Cost effective compared to other systems
* Simple to use Unlimited map linking & zoom facility
* Support for 100’s of graphics
* Display and control for multiple panels
* Event history explore and export facility to text or HTML
documents
68
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
SYNCRO GUIDE
Recommended MinimumNotes
Processor
Intel Pentium 1Ghz
The faster the better
Operating system
Windows® XP/Vista , 7
Will operate under Windows® 2000
Professional
Memory1Gb minimumThe larger the better.
Hard disk
10GB minimum
Graphics
1024 x 768 16M colours
The driver must allow this mode with
large fonts. Separate Graphics card with
256MB graphics memory recommended
Sound card
Any PC sound card
Loudspeaker
Any PC speakers
More convenient if built into PC.
Monitor
Any that supports above
17 inch minimum recommended
graphics driver
the larger the better. (1024 x 768)
Pointing device
Mouse essential
Third button and wheels are supported.
Touch screen option supported
PrinterOptionalAny type.
Serial ports
One RS232 per network
Isolated converter supplied for
connection to fire alarm system.
CDROM drive
Any
Required for installation of software
and updates.
Backup drive
CD Writer
To back up history.
Note: Guide will be operating 24 hours a day for many years. It may be desirable to include on site PC maintenance as part of the package.
Note: The Syncro panel to which the Guide system is connected must not have a printer fitted.
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
69
SYNCRO COMMS
Syncro Comms
Communication Module
(modem)
Product Overview
The K556 communications module enables service companies to
interrogate control panels remotely via a telephone link.
* View devices near calibration limits
The communications module is simple to install and requires a PSTN
telephone line.
* Plan maintenance visits
The module mounts on existing pillars in the control panel and is supplied
with all wiring and connections to enable speedy installation and
commissioning.
* Dial in and observe reported faults
Once connected to the control panel via the Loop Explorer software,
users can upload configuration data and event logs or take control of the
system via the virtual panel interface.
This allows the panel controls to be operated as if the user was standing
at the panel.
The Loop Explorer configuration programme (version 3.0 or higher) is
used to dial into control panels but the dial up facility will not be available
unless the PC calling the control panel is fitted with a registered dongle
(part number B2158 for parallel port or B2158USB for USB version).
70
Standard Features
* Retrieve event log
* Assist commissioning from remote location
* Offer value added service to customers
* Check software version to see if updates are available
* Retrieve configuration
* Avoid unnecessary call outs
* Simple to install
* Dongle protected access, for customers security
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
SYNCRO COMMS
Module part numberSYNCRO-K556
Size190mm(H) x 62mm(W) x 40mm(D)
Supply voltage
21V to 30V DC
Current consumption50 milliamps
ConnectionPSTN
Dongle part number
B2158 (parallel port)
B2158USB (USB serial port)
Note: One dongle required per user, to enable the
‘dial in’ facility within the Loop Explorer program
Note: The Communications Module is compatible with Loop Explorer Software version 3 or
above and Syncro Control Panel Firmware version 3 or above.
QLD 07 3252 5366 NSW 02 9644 7144
VIC 03 9544 2211
71

SYNCRO AS-2M4 Brochure

Transcription

Similar documents

Westfalia Syncro Multivan

MK170 FireCell Control Panel Hybrid Software iss2

DORMA AGILE 150 / SYNCRO —

Overland Journal Fall 2011

7 Case Study, JCT600 Car showroom, Castleford

flash upgrade instructions

1991 Volkswagen Syncro 4WD Westfalia Full Camper

Building Code Training – August 30th at Burgundy Basin Inn

Syncro - ITW Security and

Installation Manual for Lowering Module Bentley Continental GT