PD-II MANUAL

Transcription

PD-II MANUAL

PD-II MANUAL
1
< Table of Contents >
1. Introductions ....................................................................................................................4
1.1.
1.2.
1.3.
1.4.
The Preface.......................................................................................................4
Precautions .......................................................................................................4
Specifications (CE)............................................................................................5
Sealing Method .................................................................................................7
2. Calibration Mode .............................................................................................................8
2.1.
How to Go to Normal mode (C – 0) ..................................................................9
2.2
How to Confirm Span Calibrated A/D Value(C – 1) ..........................................9
2.3.
Span Calibration(C – 3).....................................................................................9
2.4.
Capacity Display and Option Setting(C – 4) ...................................................10
2.4.1. UNIT, TARE Setting(C–4–1)......................................................................10
2.4.2. Capacity Setting(C–4–2) ............................................................................10
2.4.3. Comma Setting (C–4–3) ............................................................................11
2.4.4. Save Setting(C–4–4)..................................................................................11
2.5.
Averaging A/D Value(C - 5).............................................................................11
2.6.
Real A/D Value(C – 6).....................................................................................12
2.7.
%
Calibration
(C
–
7)………………………………………………………………122
2.8.
Gravity Constant (C – 9) .................................................................................13
2.9.
ECR INTERFACE ...........................................................................................13
2.9.1
ECR Interface.............................................................................................13
2.9.2
ECR Type Selection...................................................................................13
Table 1 ............................................................................................................................14
3. INTERFACE WITH EXTERNAL DEVICE .....................................................................15
3.1.
INTERFACE with RS-232C.............................................................................15
3.1.1.
3.1.2.
3.1.3.
3.1.4.
TYPE-2 INTERFACE .................................................................................15
TYPE-3 INTERFACE .................................................................................16
TYPE-0 and TYPE-1 INTERFACE ............................................................17
TYPE-4 INTERFACE .................................................................................18
3.1.5.
3.1.6.
3.1.7.
3.1.8.
TYPE-5 INTERFACE .................................................................................20
TYPE-6 INTERFACE .................................................................................21
TYPE-7 INTERFACE…………………………………………………………..22
TYPE-8 INTERFACE…………………………………………………………..23
3.2.
INTERFACE with 4-BIT PARALLEL ...............................................................23
2
3.2.1.
3.2.2.
TYPE-0 and1 INTERFACE ........................................................................23
COMMUNICATIONS BY USING UNIVERSAL 4-BIT PARALLEL ............26
4. The Schematics and Diagram .......................................................................................31
4.1.
System Block Diagram....................................................................................31
4.2.
Circuit Diagram................................................................................................32
4.2.1. Main............................................................................................................32
4.2.2. Power .........................................................................................................33
4.2.3. Display........................................................................................................34
4.2.4. Communication (Serial and Parallel) .........................................................35
4.3.
Wiring Diagram................................................................................................36
4.4.
Parts Location .................................................................................................37
4.4.1. Main and Power Part..................................................................................37
4.4.2. Display Part ................................................................................................38
5. EXPLODED VIEW.........................................................................................................39
6. PARTS LIST ..................................................................................................................41
3
1. Introductions
1.1. The Preface
Thank you for purchasing of our CAS scale.
This scale has been designed with CAS reliability, under rigid quality control
and with outstanding performance.
Your departments can enjoy with this high quality reliable CAS product.
We believe that your needs will be satisfied and you will have proper reliability
with in variable weight.
This manual will help you with proper operations and care of the PD-II series.
Please keep it handy for the future references.
1.2. Precautions
To ensure that you get the most from your scale, please follow these instructions.
1. Do not disassemble the scale. When any damage or defect occurs, contact your CAS authorized
dealer immediately for proper repair.
2. Do not overload beyond the maximum weight limit.
3. Scale must be grounded to minimize electricity static. This will minimize defect or electric shock.
4. Do not pull the plug by its cord when unplugging. Damaged cord could cause electric shock or
fire.
5. To prevent from fire occurring. Do not place or use the scale near flammable or corrosive gas.
6. To reduce electric shock or incorrect reading. Do not spill water on the scale or place it in humid
condition.
7. Avoid placing the scale near heater or in direct sunlight.
8. Insert plug firmly to wall outlet to prevent electric shock.
Make sure to plug your scale into the proper power outlet. For maximum performance,
plug into a power outlet 30 minutes before the usage for warm up.
9. For consistent and accurate reading, maintain periodical check by your CAS authorized dealer.
10. Avoid sudden shock to the scale. Internal mechanism could be damaged.
11. Grab on the bottom of the scale when moving. Do not hold by the platter.
12. Place the scale on firm and temperature consistent environment.
13. If the scale is not properly level, please adjust the 4 legs at the bottom of the scale
(turn legs clockwise or counterclockwise) so as to center the bubble of the
leveling gauge inside the indicated circle.
14. Keep the scale away from other electromagnetic generating devices. This may interfere with
accurate reading.
4
1.3. Specifications (CE)
MODEL
CAPACITY
INTERNAL
RESOLUTION
EXTERNAL
RESOLUTION
TARE
SUBTRACTION
PDII – 6kg
PDII – 15kg
PDII – 30kg
PDII-60kg
Single Interval
Single Interval
Single Interval
Single Interval
6 kg
15 kg
30 kg
60 kg
1 / 90,000
1 / 90,000
1 / 90,000
1 / 90,000
1 / 3,000
1 / 3,000
1 / 3,000
1 / 3,000
-6kg
– 15kg
– 30kg
-60kg
DISPLAY
VFD 6 digit
DISPLAY LAMP
ST, ZERO, NET, kg, lb
INTERFACE
RS – 232C, 4-Bit Parallel Communication. (ECR Interface)
PRODUCT SIZE
380× 280 × 79 [mm]
PLATTER SIZE
380 × 280 [mm]
OPERATING
- 10 °C ~ +40 °C
TEMPERATURE
POWER
SOURCE
OPTION
AC 230 V / 50 Hz
Remote Display, Customer Display
5
Pound(lb) Version (UL)
MODEL
Capacity
INTERNAL
RESOLUTION
EXTERNAL
RESOLUTION
PD2 – 15LB
PD2 – 30LB
PD2 – 60LB
PD2-150LB
Single Interval
Single Interval
Single Interval
Single Interval
15 lb / 0.005 lb
30 lb/ 0.01 lb
60 lb/ 0.02 lb
150 lb / 0.05 lb
Dual Interval
Dual Interval
Dual Interval
Dual Interval
6 lb / 0.002 lb
15lb / 0.005 lb
30 lb/ 0.01 lb
60 lb / 0.02 lb
15 lb / 0.005 lb
30 lb/ 0.01 lb
60 lb/ 0.02 lb
150 lb / 0.005 lb
1 / 90,000
1 / 90,000
1 / 90,000
1 / 90,000
1 / 3,000
1 / 3,000
1 / 3,000
1 / 3,000
Display
VFD 6 digit
DISPLAY LAMP
STABLE, ZERO.
INTERFACE
RS – 232C, 4-Bit Parallel Communication.( ECR Interface )
PRODUCT SIZE
380× 280 × 79 [mm]
380× 280
PLATTER SIZE
OPERATING
- 10 °C ~ +40 °C
TEMPERATURE
OPTION
POWER
SOURCE
[mm]
Remote Display, Option Display
AC 120 V / 60 Hz
6
1.4. Sealing Method
7
2. Calibration Mode
To go to calibration mode, turn on the power while pressing the calibration switch.
The display shows “CAL” three times, and then “C-0”.
Mode Selection : [#]key or [*] key
Enter : [ZERO] key
MODE
DESCRIPTION
C–0
Normal Mode
C–1
Span calibrated A/D value
C–3
Span Calibration
C–4
Capacity Display and Option Setting
C–5
Averaging A/D Value
C–6
Real A/D Value
C–7
% Calibration (10%~100%)
C–9
Gravity Constant
Calibration Mode
MODE
C-4-1
Save Setting
DESCRIPTION
Calibration Unit, Tare setting
C-4-2
Capacity setting
Capacity Setting
C-4-3
Comma setting
Comma Setting
C-4-4
Save setting
Capacity Setting
C – 4 Setting
8
2.1. How to Go to Normal Mode (C – 0)
To go to calibration mode, turn on the power while pressing the calibration switch.
The
display shows “CAL” three times, and then “C-0”.
To go to Normal mode, press the [ZERO] key.
2.2
How to Confirm Span Calibrated A/D Value(C – 1)
(1) To go to calibration mode, turn on the power while pressing the calibration switch.
The
(2) Press the [#] key until the display shows “C – 1” .
(3) Press the [ZERO] key, the display shows “0”.
(4) Place full capacity on the platter. The display shows “90,000”. If the number is not
“90,000”, press the [*] or [#] key to have number up or down.
(5) Press the [ZERO] key, the display shows “C – 1”. You can change the mode by pressing
[#] or [*] key.
2.3
Span Calibration(C – 3)
The
(2) Press the [#] key until the display shows “C – 3”.
(3) Press the [ZERO] key, the display shows “UnLOAd”.
(4) Remove items from the platter and press the [ZERO] key.
The display shows “StAbLE”
and then “LOAd”. (If you want to finish this mode, press the [#] key.
(5) Place full capacity on the platter and press the [ZERO] key. The display shows “C-3
End” and “C-3”.
(6) Remove full capacity from the platter. You can change the mode by pressing [#] or [*]
key.
9
2.4 Capacity Display and Option Setting(C – 4)
For pariculars please inquire at CAS .
Key operation :
◆ Press the ZERO key to enter setting value.
◆ Press the [#] key to change digit position.
◆ Press the [* ] key to have number Up.
2.4.1 UNIT, TARE Setting(C–4–1)
B7
B6
B5
Display
Calibration
Unit
Unit
0:kg
B3
B4
NTEP
B1
Initial
TARE Relase
0:TARE
0:10%
0:kg
1:One time Tare
ZERO
1: NTEP
1:2%
TARE
0:Successive Tare
1:TARE,
1:lb
Don’t care
B0
Zero
0: Others
1:lb
B2
Don’t care
Don’t care
2.4.2 Capacity Setting(C–4–2)
B7
B6
B5
B4
B3
CAPACITY
B2
B1
INTERVAL
Kg
lb
00011
6
15
00 : Single
00111
15
30
01 : Dual
01001
30
60
01100
60
150
10
B0
2.4.3 Comma Setting (C–4–3)
B7
B6
B5
B4
B3
B2
B1
B0
B4
B3
B2
B1
B0
Comma
Dislplay
1: Possible
0: Impossible
2.4.4 Save Setting(C–4–4)
B7
B6
B5
UNIT
CHANGE
1: Possible
0: Impossible
Î If NTEP(C-4-1 3rd bit) is set, please do not care of “C-4-4” setting.
2.5 Averaging A/D Value(C - 5)
(3) Press the [ZERO] key, the display shows averaging A/D.
(4) Press the [ZERO] key to finish this mode.
(5) You can change the mode by pressing [#] or [*] key.
11
The
2.6
Real A/D Value(C – 6)
The display
shows “CAL” three times, and then “C-0”.
(3) Press the [ZERO] key, the display shows real A/D value.
(4) Press the [ZERO] key to finish this mode.
2.7
% Calibration (C – 7)
(1) To go to calibration mode, turn on the power while pressing the calibration switch. The display
(3) Press the [ZERO] key, the display shows “Per 10”.
(4) Press the [*] key to have number up or down The display shows 10, 20, 30, 40, 50, 60,
70, 80 and 90 every time pressing [*] key.
If you want to calibrate PDII-150lb with 30 lb, select 20.
(5) Press the [ZERO] key, the display shows “UnLOAd”.
(6) Remove items from the platter and press the [ZERO] key.
The display shows “StAbLE”
and then “LOAd”.
(7) Place 20% weight of full capacity that you setup on step (3). And press the [ZERO] key,
the display shows “StAbLE” and then “C-7End”.
(6) Remove the weight from the platter. You can change the mode by pressing [#] or [*]
key.
12
2.8
Gravity Constant (C – 9)
The display
(3) Press the [ZERO] key the display shows ”C91 “ and “ 9.7994”. Default value is 9.7994.
(4) You can change gravity constant for calibration place. Press the [*] key to have number
up or down. To move to next digit, press the [#] key.
(5) To save it, press the [ZERO] key. The display shows “C92” and “ 9.7994”.
(6) You can change gravity constant for using place. Press the [*] key to have number up or
down. To move to next digit, press the [#] key.
(7) Press the ZERO key, the display shows “C9-End” and “C – 9”.
2.9
ECR INTERFACE
2.9.1
ECR Interface
PD-II can interface with most ECRs by selecting TYPE 0 to TYPE 6.
2.9.2 ECR Type Selection
(1) Make sure that power is OFF. While pressing [#] key, turn on the power. “EcrSEt” is shown
on the display. And then current ECR type is shown on the display as “tYPE-2.
(2) If you select ECR type 5, press the [#] key until the display shows it. (Refer to Table 1.)
(3) To save current ECR type, press the ZERO key.
13
Table 1
Description
MENU
4-Bit Parallel
ECR-TYPE 0
RS-232 Serial
TEC 4 Digit 4Bit Paralle (New kg)
Most P.O.S, ECRs and Some TEC P.O.S
System
ECR-TYPE 1
TEC 5 Digit 4Bit Paralle (Old kg)
SHARP ER-Axxx, ER-A450T, New SANYO
ECR-TYPE 2
ECRs using RS-232 and others
ECR-TYPE 3
Most P.O.S System
CRS, NCR2170, SAMAUNG ER-5100,
ECR-TYPE 4
ER5115 and Many other ECRs
Universal 4 Bit Parallel
NCI General.
ECR-TYPE 5
SAMSUNG ER-5100
Most P.O.S Software
ECR-TYPE 6
SAMSUNG ER-670
ECR-TYPE7
SAMSUNG ECR(SPAIN)
ECR-TYPE8
SAMSUNG(PORTUGAL)
※ Serial Communication
Æ 9600 Baud rate, 7 Data bit, Even Parity, 1 Stop bit
14
3 INTERFACE WITH EXTERNAL DEVICE
3.1
INTERFACE with RS-232C
1
1
6
6
2 RxD
`
2
7
7
3
8
3 TxD
8
4
9
4
9
5
ECR(삼성), PC
D-SUB Connector
5
PD-II
(9-PIN SUB CONNECTOR)
Î 7-BIT ASCII code
Î Even parity
Î 1 stop bit
Î 9600 baud rate
3.1.1 TYPE-2 INTERFACE
: Discontinual RS-232C Interface
Î SHARP ER-AXXX, ER-A450T, New SANYO ECRs using RS-232,TOLEDO 3213 etc.
1) PROTOCOL
ECR
Command
SCALE(PD-II)
------------Æ
<W>
Å------------
Response
<STX> 0XXXX <CR>
: lb weighing mode
or <STX> XXXXX <CR>
: kg weighing mode
Error message
: <STX>?<status byte><CR>
15
== STATUS BYTE ==
PARITY BIT
ALWAYS==1
Bit 7
cf)
ZERO
Bit 6
Bit 5
MINUS
Bit 4
Bit3
OVERLOAD
Bit 2
Bit 1
W : 57H (ASCII code)
STX : 02H (ASCII code)
CR
: ODH (ASCII code)
Ex)
Weight
:
12.34 lb
ECR
W<57H>
SCALE
------Æ
<02H><30H><31H><32H><33H><34H><0DH>
Å------
STX
0
1
2
3
4
: ASCII code
CR
: Continual RS-232C Interface
Î SHARP ER-AXXX, New SANYO ECRs using RS-232,TOLEDO 3213 etc
1) PROTOCOL
ECR
Command
SCALE(PD-II)
------------Æ
<W>
Å------------
Response
<STX> 0XXXX <CR>
: lb weighing mode
<STX> XXXXX <CR>
: kg weighing mode
Error message
<CR>
------------Æ
: <STX>?<status byte><CR>
Stop transmitting data
16
MOTION
Bit 0
Ex)
Weight
:
12.34 lb
ECR
SCALE
W<57H>
------Æ
Å------<02H><30H><31H><32H><33H><34H><0DH> : ASCII code
STX
0
1
2
3
4
CR
<02H><30H><30H><30H><30H><30H><0DH>
STX
0
0
0
0
0
: ASCII code
CR
Å------<02H><3FH><44H><0DH>
STX
? MINUS
CR
TRANSMISSION PROCEDURE
(1) PD-II sends data to External Device whenever weight is changed after receiving <W> signal
from the External Device.
(2) PD-II stops sending data when receives <CR> signal from the External Device.
External Device
<W>
<CR>
------Æ
Å-----
DATA (If weight is changed)
Å------
DATA (If weight is changed)
------Æ
Stop transmitting data
3.1.3 TYPE-0 and TYPE-1 INTERFACE
Î Most P.O.S Systems, ECRs and some TEC P.O.S Systems.
1) PROTOCOL
EXTERNAL DEVICE
SCALE(PD-II)
<ENQ>
------------Æ
Initiate communication
<DC2>
------------Æ
Request of weight data
Å------------
<ACK>
: Acknowledge the request of weight data
Inquiry
17
i>
ii>
Å------------
<STX>
: Start Transmission
Å------------
<ID>
: Scale type identifier
Å------------
<W5>
: Weight data
Å------------
<W4>
: Weight data
Å------------
<W3>
: Weight data
Å------------
<W2>
: Weight data
Å------------
<W1>
: Weight data
Å------------
<BCC>
: Block Check Character
Å------------
<ETX>
: End Transmission
Scale Type Identifier
41H = 15 kg
44H = 30 lb
43H = 6 kg
46H = 15 lb
NA = 3 kg
NA = 6 lb
42H = 25 kg
45H = 50 lb
Block Check Character
: <BCC> has all data bytes except <STX> and <ETX> through exclusive OR(XOR).
* Parity Bit : Even
- Data Byte :
<STX><ID><W5><W4><W3><W2><W1><BCC><ETX>
Î NCI ECR(NCR2170), SAMSUNG ER-5100,ER-5115, CRS .etc
1) PROTOCOL
<W>
------------Æ
<CR>
------------Æ
Inquiry
Å------------
<LF> XX.XXX
LB <CR>
Å------------
<LF> S b1b2 <CR><ETX>
lb CASE
Å------------
<LF> XX.XXX KG <CR>
Å------------
18
(A)
XX.XXX
(B)
LB = The Characters L and B
(C)
KG =
(D)
S
(E)
b1b2 = Two status Characters
i>
= Weight value
The Characters K and G
= The Character S
Status Bytes
Bit7
Parity Bit
Parity Bit
Bit6
0
0
Bit5
1 (Always 1)
1 (Always 1)
Bit4
1 (Always 1)
1 (Always 1)
Bit3
0
0
Bit2
0
0
1 = Scale at Zero
1 = Over Capacity
0 = Not at Zero
0 = Not Over Capacity
1 = Scale in Motion
1 = Under Capacity
0 = Stable
0 = Not Under Capacity
Bit1
Bit0
ii>
Simplified Status Codes
B1
B2
ASCII
ASCII
STATUS
Character
Character
Definition
(ASCII Code)
(ASCII Code)
0 (30H)
0 (30H)
OK
1 (31H)
0 (30H)
Motion
2 (32H)
0 (30H)
Scale at Zero
0 (30H)
1 (31H)
Under capacity
0 (30H)
2 (32H)
Over capacity
19
Î NCI GENERAL , SAMSUNG ER-5115, ER-5100 and Most P.O.S Software
1) PROTOCOL
<W>
------------Æ
<CR>
------------Æ
Inquiry
Å------------
<LF> XX.XXX
LB <CR>
Å------------
<LF> b1b2 <CR><ETX>
lb CASE
Å------------
<LF> XX.XXX KG <CR>
Å------------
(F)
XX.XXX
(G)
LB = The Characters L and B
(H)
KG =
(I)
b1b2 = Two status Characters
i>
= Weight value
Status Bytes
Bit7
Parity Bit
Parity Bit
Bit6
0
0
Bit5
1 (Always 1)
1 (Always 1)
Bit4
1 (Always 1)
1 (Always 1)
Bit3
0
0
Bit2
0
0
1 = Scale at Zero
1 = Over Capacity
0 = Not at Zero
0 = Not Over Capacity
1 = Scale in Motion
1 = Under Capacity
0 = Stable
0 = Not Under Capacity
Bit1
Bit0
20
ii>
3.1.6
Simplified Status Codes
B1
B2
ASCII
ASCII
STATUS
Character
Character
Definition
(ASCII Code)
(ASCII Code)
0 (30H)
0 (30H)
OK
1 (31H)
0 (30H)
Motion
2 (32H)
0 (30H)
Scale at Zero
0 (30H)
1 (31H)
Under capacity
0 (30H)
2 (32H)
Over capacity
TYPE-6 INTERFACE
Î 8 Data bit
Î Noneparity
Î 1 stop bit
Î 9600 baud ate
Î SAMSUNG ECR (ER-670)
1> PROTOCOl
EXTERNAL DEVICE
<ENQ>
<DC1> or <DC2>
SCALE(PD-II)
------------Æ
Initiate communication
Å------------
<ACK>
------------Æ
DC1 : For Weight Data
: Acknowledge the request of weight data
DC2 : For All Data ( PD-II NOT USE)
Å------------
Send Data Block
1> The Data Trains
1. “DC1”
SOH
STX
Command
STA
SIGN
W5
W4
W3
W2
DATA BLOCK
21
W1
W0
UN1
UN0
BCC
ETX
EOT
Command
z
-
Remark
STA : A WEIGHING STATUS OF THE SCALE
SCALE IS STABLE ->”S”, NOT STABLE -> “U”
-
SIGN : SIGN OF THE WEIGHT DATA
ZERO AND POSITIVE WEIGHT -> “ “ , NEGATIVE WEIGHT -> “-“
OVER LOAD -> “F”
-
W5 THROUGH W0 –> WEIGHT DATA
BUT ALL “F” WHEN THE SCALE IS PUT ON OVER LOAD.
-
UN1 THROUGH UN0 -> UNIT OF WEIGHT ( Kg OR Lb)
-
BCC
: BLOCK CHECK CHARACTER
: RS-232C Interface
Î 8 Data bit
Î None parity
Î 1 stop bit
Î 9600 baud rate
Î SAMSUNG ECR (SPAIN)
1) PROTOCOL
ECR
SCALE(PD-II)
Command
------------Æ
<$>
Å------------
Response
XXX.XXX <CR>
cf)
$ : 24H (ASCII code)
“.” : 2EH (ASCII code)
CR
: ODH (ASCII code)
Ex)
Weight
:
12.34 kg
ECR
$<24H>
SCALE
------Æ
Å------
<30H><31H><32H><2EH><3H><34H><0DH>
0
1
2
22
.
3
4
CR
: ASCII code
3.1.8
TYPE-8 INTERFACE
Î SAMSUNG (PORTUGAL)
1) PROTOCOL
<W>
------------Æ
<CR>
------------Æ
Inquiry
Å------------
<LF> XXX.XX KG <CR>
Å------------
<LF> S00 <CR><ETX>
lb CASE
Å------------
<LF> XX.XXX KG <CR>
Å------------
i.
XXX.XX
ii.
KG =
iii.
S
= The Character S
00
= <30H><30H>
iv.
= Weight value
3.2 INTERFACE with 4-BIT PARALLEL
3.2.1
TYPE-0 and1 INTERFACE
Î TEC ECR
⒜
New : Type 0 (4 Digit)
⒝
Old : Type 1 (5 Digit)
(1) CONNECTOR
:
25 PIN D-SUB CONNECTOR
(2) LOCATION
:
BOTTOM OF THE SCALE
(3) INTERFACE WITH ECR(TEC)
: PIN ASSIGNMENT
PIN NO.
DOCUMENT
1
DATA1
(Output from PD-II to ECR)
2
DATA2
3
DATA3
4
DATA4
11
CLOCK
(Input from ECR to PD-II)
23
13
MOTION
19
ENABLE
20
SIGNAL READY (Output from PD-II to ECR)
21
ENABLE
22
GND
23
GND
24
GND
(4) DATA OUTPUT FORMAT
: INVERTED BCD DATA!!!
Example1)
Weight
:
12.34 lb & 87.56 lb
lb Weight Mode
1
2
3
4
8
7
5
6
DATA1
0
1
0
1
1
0
0
1
DATA2
1
0
0
1
1
0
1
0
DATA3
1
1
1
0
1
0
0
0
DATA4
1
1
1
1
0
1
1
1
Example2)
Weight
: 5.342 kg & 13.897 kg
kg Weight Mode
5
3
4
2
1
3
8
9
7
DATA1
0
0
1
1
0
0
1
0
0
DATA2
1
0
1
0
1
0
1
1
0
DATA3
0
1
0
1
1
1
1
1
0
DATA4
1
1
1
1
1
1
0
0
1
(5) SIGNAL DESCRIPTION
MOTION : LOW
---Æ
HIGH ---Æ
SIGNAL READY :
WEIGHT IS STABLE
WEIGHT IS UNSTABLE
HIGHT ---Æ
:
LOW ---Æ
DATA READY ( The acknowledge signal for enabling)
DATA NOT READY
24
(6) PIN CONNECTION
ECR ( TEC )
PD-II
16 PIN CONNECTOR
1
Å---------------------------Æ
1
3
Å---------------------------Æ
2
5
Å---------------------------Æ
3
7
Å---------------------------Æ
4
11
Å---------------------------Æ
11
19
Å---------------------------Æ
13
15
Å---------------------------Æ
19
13
Å---------------------------Æ
20
15
Å---------------------------Æ
21
2
Å---------------------------Æ
22
4
Å---------------------------Æ
23
6
Å---------------------------Æ
24
8
Å---------------------------Æ
25
(Jump with 19 pin)
(7) TIMMING DIAGRAM
MOTION
(PD-II --> ECR)
ENABLE
(ECR --> PD-II)
tr
MOTION
(SCALE --> PD-II)
tc
MOTION
(ECR --> PD-II)
tf
A
note>
B
C
D
E
tr : When tr is more than 3 sec, the ECR judges SCALE DOWN < 100 ns
tc
:
< 20 usec
tf :
< 20 usec
25
DATA FORMAT
:
1>
LB weighing mode
---Æ
4 bit : AB.CD (lb)
5 bit : BC.DE (lb)
2>
KG weighing mode ---Æ
AB.CDE (kg)
3.2.2 COMMUNICATIONS BY USING UNIVERSAL 4-BIT PARALLEL
Î SANYO, TOLEDO, CASIO, SHARP, etc.
(1) CONNECTOR
:
(2) LOCATION
:
BOTTOM OF THE SCALE
(3) PIN ASSIGNMENT AND PIN CONNECTION
(3.1)
INTERFACE WITH ECR (SANYO)
⒜ PIN ASSIGNMENT
PIN NO.
DOCUMENT
1
DATA1
2
DATA2
3
DATA3
4
DATA4
11
CLOCK
19
ENABLE
(Input fromm ECR to PD-II)
22
GND
23
GND
24
GND
⒝ PIN CONNECTION
ECR ( SANYO )
PD-II
1
Å---------------------------Æ
1
2
Å---------------------------Æ
2
3
Å---------------------------Æ
3
4
Å---------------------------Æ
4
5
Å---------------------------Æ
11
6
Å---------------------------Æ
19
7
Å---------------------------Æ
22
26
8
Å---------------------------Æ
23
9
Å---------------------------Æ
24
(3.2)
INTERFACE WITH ECR (CASIO)
⒜ PIN ASSIGNMENT
PIN NO.
DOCUMENT
1
DATA1
2
DATA2
3
DATA3
4
DATA4
11
CLOCK
13
MOTION
19
ENABLE
21
OUT OF RANGE
22
GND
23
GND
⒝ PIN CONNECTION
ECR ( CASIO )
PD-II
11
Å---------------------------Æ
1
7
Å---------------------------Æ
2
8
Å---------------------------Æ
3
9
Å---------------------------Æ
4
12
Å---------------------------Æ
11
13
Å---------------------------Æ
13
10
Å---------------------------Æ
19
14
Å---------------------------Æ
21
15
Å---------------------------Æ
22
16
Å---------------------------Æ
23
27
(3.3)
INTERFACE WITH ECR (SHARP)
⒜ PIN ASSIGNMENT
PIN NO.
DOCUMENT
1
DATA1
2
DATA2
3
DATA3
4
DATA4
11
CLOCK
13
MOTION
19
ENABLE
(Input form ECR to PD-II)
21
OUT OF RANGE
22
GND
23
GND
24
GND
⒝ PIN CONNECTION
ECR ( SHARP )
PD-II
1
Å---------------------------Æ
1
3
Å---------------------------Æ
2
4
Å---------------------------Æ
3
5
Å---------------------------Æ
4
7
Å---------------------------Æ
11
15
Å---------------------------Æ
13
8
Å---------------------------Æ
19
9
Å---------------------------Æ
21
10
Å---------------------------Æ
22
11
Å---------------------------Æ
23
12
Å---------------------------Æ
24
(3.4)
① MOTION
SIGNAL DESCRIPTION
:
LOW
---Æ
HIGH
---Æ
WEIGHT IS STABLE
WEIGHT IS UNSTABLE
28
② OUT OF RANGE
:
HIGH ---Æ
HIGH LEVEL FOR WEIGHT BETWEEN ZERO AND FULL CAPACITY
LOW
OTHERWISE
---Æ
(2) DATA OUTPUT FORMAT
: BCD
Example1)
Weight
:
12.34 lb & 87.56 lb
lb Mode
1
2
3
4
8
7
5
6
DATA1
1
0
1
0
0
1
1
0
DATA2
0
1
1
0
0
1
0
1
DATA3
0
0
0
1
0
1
1
1
DATA4
0
0
0
0
1
0
0
0
Example2)
Weight
:
5.342 kg & 11.897 kg
kg Mode
5
3
4
2
11(B)
8
9
7
DATA1
1
1
0
0
1
0
1
1
DATA2
0
1
0
1
1
0
0
1
DATA3
1
0
1
0
0
0
0
1
DATA4
0
0
0
0
1
1
1
0
29
(3) TIMMING DIAGRAM
TD4
COMPLETE SEQUENCE
TD5
ENABLE
CLOCK
TD3
TD2
A
B
DATA1
DATA2
DATA3
DATA4
A :
B
Note>
UNIT
: Tenth’s place
C
D
X.000
0.X00
C :
Hundredth’s place 0.0X0
D :
Thousandth’s place 0.00X
TD2
: < 100 ns --Æ data set up delay from rising edge of clock
TD3
: 200 ns maximum --Æ data set up delay from Enable
TD4
: 1 microsec. minimum --Æ time between interrogation
TD5
: 200 ns minimum
MAXIMUM CLOCK FREQUENCY : 100 KHZ
30
NEXT SEQ.
4
4.1
The Schematics and Diagram
System Block Diagram
6-Digit VFD
Display 부는 본체 및 Post 에 사용자가
간편하게 설치 하여 사용.
VFD Driver (PT6311)
Wire 길이는 1.5 m 이내로 함
Load
Cell
ADC Circuit
(Dual Sloop type)
CPU
AC 220V
Transform er
KEY
(ZERO ,T ARE,Kg/Lb ,
POW ER ON/OFF KEY)
Pow er
M odule
RS-232C
Serial
SANYO,CASIO,ESPER,
SHARP,TEC ...etc
Parallel Communication (4-Bit BCD)
9 pin D-SUB Connector
25 pin D-SUB Connector
ECR Interface Circuit
ECR , POS System .
31
4.2
4.2.1
Circuit Diagram
Main
VDD
R3~5,14~16
uPD789177
C31
100u
28
37
9
44
24
CON 5
8 Vpp
XTAL
5.0MHz
R13
0.1u
CAL
CON8
P61/AN11
P62/AN12
P63/AN13
P64/AN14
P65/AN15
P66/AN16
P67/AN17
uPD789177
U5
A0
A1
A2
VSS
24C16N
To VFD Driver DIN
To VFD Driver CLK
To VFD Driver STB
VDD
WP
SCL
SDA
8
7
6
5
CON1
25
RESET
R6
100k
0.5%
C18
0.1u
3
3
INT CLK (TO A/D)
CAPTURE (From A/D)
VDD
U3
KIA7045F
R2
10K
0.5%
JP3
VDD
VDD
6 /RESET
7
8 Vpp
9
10
1
2
3
4
5
0.5%
R17 10K
R18 10K
0.5%
CON10
C15
VDD
1
2
3
4
To ECR (Motion,Pin#13)
VDD
To Q1
C19
0.1u
To ECR (Out of range, CON 7 Pin#21)
To ECR (Overcapacity, CON 7 Pin#20 )
IC 74HC670 Pin#14,WA
IC 74HC670 Pin#13,WB
IC 74HC670 Pin#12,GW
18
19
P21/SO20/TxD20
P22/SI20/RxD20
X1
X2
XT2
2
3
4
5
6
7
8
10k
0.5%
C5
IC0(Vpp)
27
26
23
P31/INTP1/TO81
P30/INTP0/TI81/CPT90
C16
18pF
VDD
22
C17
18pF
13
12
R7
10k
P10
P60/AN10
P11
0.1u
10
1
11
C33
0.1u
P32/INTP21/TO90
P33/INTP3/TO82/BZO90
P20/SCK20/ASCK20
C14
33
32
31
30
21
20
P01
P00
P26/TO80
P25/TO80/SS20
P24/SDA0
P23/SCL0
0
CON9
Display Con 1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Vsso
Vss1
AVss
AVref
XT1
1
+
0.1u
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
To U14 IC(74HC670) Pin#15
21
C32
10K
0.5%
42
41
40
39
38
36
35
34
P53
P52
P51
P50
P05
P04
P03
P02
14
15
16
Display Con 2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Vddo
Vdd1
AVdd
2
29
17
43
0.1u
GND
VDD
Connect CPU Pin#22 (IC <Vpp>)
R9 10k
0.5%
R10 10k
0.5%
R11
100k 0.5%
Q1
1504
From CPU P1.1
L9,10,11
6100-PPD-2000-A
Title
TDK221 X 3
MAIN CIRCUIT (uPD789177) For VFD
32
Size
Document Number
Custom
First Drawing H.J
Date:
Tuesday, August 12, 2003
Rev
Sheet
1
of
1
4.2.2
2
Power
TRANSFORMER50
SW50
1
3
F50
1
3
FUSE
.
BD1
16.5V/100mA
IC2
2 I
+
EC2
KA7912
C1
O
3
-12v
EC5
COM
C4
1
470uF
104
+
+
RB153
AC MALE(220V)
100uF
104
CON1
8.8V/100mA
1
2
3
4
5
6
7
8
9
2
J50
3
AC220V
E
Noise Filter
(CA5-V32)
1
29V/50mA
BD2
IC1
L2
FERITE
+5V
1 I
+
EC3 +
KA7805
C2
O
3
+ 100uF C3
COM
2
RB153
EC4
1000uF 104
104
CON7
To Digital Power(5V)
3.3u(tantal)
C12
C13
VDD(+5v)1
2
3
4
5
6
7
8
C11
0.01u
4.7uF
1.65V/700mA
D1
VEE(-30V)
1.65V/700mA
2
4
1N4004
D2
To VFD Driver
1N4004
No artwork
EC1
ZD1
330uF/50V
+
6.8V 1w
ZD2
: POWER GND
: DIGITAL GND
6.8V 1w
L6
R1
FERITE
: ANALOG INPUT GND
30k
FL+
AGND
: ANALOG GND
FL-
To VFD Display
: SHIELD GND
-12V
471u
VDD(+5V)
-12v
L7
JP1
L35
L8
To A/D MODULE
+ EC6
+ EC7
330uF/25V
EC8
+
AGND
330uF/25V
EC9
+
VREF
: ANALOG REFERENCE GND
330uF/25V
To Analog Module Power(5V)
330uF/25V
6140-PPD-2000-A
Title
Power Circuit for PD-II VFD Version
Size
Document Number
Custom
<Doc>
Date:
33
Rev
<RevCode>
Sheet
1
of
1
Display
a
b
c
d
e
g
f
DP
TR
COM
FL+
H2
36
35
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
a
b
c
DP
COM
1D
2D
3D
VFD
U100
VDD3
14
33
C1
0.1u
45
52
VSS
OSC
L1,2,3
TDK221 X 3
VDD(+5V)
VEE (-30V)
+FL
13
12
11
10
R1
56k
IC
SW1
SW2
SW3
SW4
7
VDD2
DOUT
DIN
CLK
STB
51
10 k
R 3,4,5
VDD1
U102
PT6311
1
2
3
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Key4
Key3
Key2
Key1
VDD
VEE
5
6
8
9
Grid8
Grid7
Grid6
Grid5
Grid4
Grid3
Grid2
Grid1
34
VDD
37
38
39
40
41
42
43
44
LED1
LED2
LED3
LED4
LED5
FL-
H1
1D
2D
3D
4D
5D
6D
7D
50
49
48
47
46
4D
5D
6D
7D
TR
d
e
g
f
Seg20/Grid9
Seg19/Grid10
Seg18/Grid11
Seg17/Grid12
Seg16/Grid13
Seg15/Grid14
Seg14/Grid15
Seg13/Grid16
Seg12
Seg11
Seg10
Seg9
Seg8
Seg7
Seg6
Seg5
Seg4
Seg3
Seg2
Seg1
4.2.3
U1
VDD
VEE(-30V)
10 k
R 6,7,8
6110-PPD-2000-A
Title
-FL
ZERO TARE
PD-II DISPLAY PART (MAIN)
Size
Document Number
Custom
Designed by H.J Chang
KG/LB
CON12
Date:
34
Rev
<RevCode>
Sheet
1
of
1
4.2.4
Communication (Serial and Parallel)
+5V
+5V
AR1
7
a
t
aU
DP
~C
0
am
to
ar
DF
:
7
D
~
0
D
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
4
t
r
o
P
CON5
16
VCC
CC2+
V-
0.1u
C2T1OUT
R1IN
T2OUT
R2IN
T1IN
R1OUT
T2IN
R2OUT
GND
5
12
13
9
WA
WB
RA
RB
GW
GR
4
1
RA
RB
C8
0.1u
/GR
TO OPTION BOARD
TO OPTION BOARD
To U14 IC74HC14 Pin #13
FROM OPTION BOARD
FROM OPTION BOARD
TO OPTION BOARD
TO OPTION BOARD
DATA4 (Pin#4)
TO OPTION BOARD
TO OPTION BOARD
FROM OPTION BOARD
To U14 IC74HC14 Pin#1
From PD-II (CPU #32 IC22 MC68705K Pin#11)
From PD-II (CPU #33 )
DATA3 (Pin#3)
3
2
10
9
7
6
DATA2 (Pin #2)
6
5
Q1
Q2
Q3
Q4
DATA1 (Pin#1)
8
10
U15
D1
D2
D3
D4
11
74HC03
data 1
data 2
data 3
data 4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
D0
D1
D2
D3
FROM MAX232 PIN#14
TO MAX232 PIN#13
U9D
WA
WB
RA
RB
GW
GR
+5V
+5V
+5V
DTR
CLK 10 R32 3K R33
1K
CLK 11
NCR VCC
CLOCK
NCR OUT
Motion
+5V
X0 (CLK00)
SIG (CLK01)
ED1
CP1
R36
1K
A1
enable
Overcapacity
out of range
DSR
J1
74HC670
C9
0.1u
11
12
10
9
+5V
1
6
3
6
5
3
74HC32
74HC32
D
Q
Q
5
GR
CLK
6
/GR
1
74HC14
2
IC13B
4
IC13A
2
/ENABLE
D
3
PR
2
RA
Q
CL
4
+5V
Q
5
RB
CLK
6
1
74HC74
/ENABLE
NCR OUT (Pin#12)
IC11A
2
/ENABLE
R20 R
1
ENABLE (25 PIN D-SUB CONNECTOR Pin #19)
CLOCK (25 PIN D-SUB CONNECTOR Pin #11)
R22 R
74HC14
C20
27pF
4
C21
27pF
r)
o
tR
cC
eE
n
no
oT
C
(
B
U
S
D
N
I
P
5
2
+5V
RA
5
Q
PR
5
PR
IC11C
RA
CL
4
RB
D
CLK
6
Q
IC11E
2
3
10
IC11F
11
12
13
CL
14
13
7
8
10
9
7
6
15
1
2
3
4
5
6
7
8
9
232
1
3
4
Q1
Q2
Q3
Q4
D1
D2
D3
D4
74HC74
74HC14
74HC14
1
J3
6
C+
14
13
5
4
12
11
1
3
#
n
i
P
U
P
C
m
o
r
F
C10
U1
10
23
##
nn
ii
PP
UU
PP
CC
mm
oo
rr
FF
To CON7 Pin#5
From CON7 Pin#6
V+
15
1
2
3
(Pin #34) D4
(Pin #33) D5
(Pin #32) D6
(Pin #31) D7
Motion
2
U14
74HC670
VDD
C7
0.1u
14
13
5
4
12
11
GR
Out of Range
Overcapacity
C42
0.1u
15
1
2
3
(Pin #38) D0
(Pin #37) D1
(Pin #36) D2
(Pin #35) D3
/ENABLE
A
0
0
0
2
D
P
P
0
4
1
6
Title
ECR Interface Circuit (POWER PCB)
Size
Document Number
<Doc>
Custom
Date:
35
Rev
<RevCode>
Sheet
1
of
1
Wiring Diagram
ECR(Serial and Parallel Interface)
or
Serial Interface Device
1
2
3
4
5
6
7
8
9
10
11
12
14
6
13
1
7
2
8
3
9
4
5
CN3
15
Trans
16
POWER
Power
TRANS
25 24 23 22 21 20 19 18 17
4.3
J1
J3
CUSTOMER and
REMOTE
DISPLAY
SERIAL
COMMUNICATION
PARALLEL
COMUNICATION
CON8
CON5
X6
ECR
INTERFACE CABLE
CN2
CN1
ANALOG M/D
MAIN
X5
CN4
LoadCell
FL-PR3
DISPLAY
(Flash Rom
Write)
36
4.4
4.4.1
Parts Location
Main and Power Part
4.4.1.1
TOP
4.4.1.2
Bottom
37
4.4.2
Display Part
4.4.2.1
Top
4.4.2.2
Bottom
38
5 EXPLODED VIEW
39
40
6 PARTS LIST
PD-II Parts List
PARTS NAME : PD-II
[PPP-PD0-153G-PPPP-P1]
Parts Code
Parts Name
Size
140-AD3-EAMP-PA01-02
ANALOG MODULE ASS'Y
AD-20H
140-PD2-EDIP-UN01-02
DISPLAY PCB ASS'Y
PD-II
EA
1
140-PD2-EMAP-UN01-02
MAIN PCB ASS'Y
PD-II
EA
1
140-PD2-EPWP-UN01-02
POWER PCB ASS'Y
PD-II
EA
1
140-PD2-MBOD-UN01-02
BODY ASS'Y
PD-II
EA
1
140-PD2-MCTB-UN01-02
C/T BOX ASS'Y
PD-II
EA
1
140-PD2-MDIC-UN01-02
DISPLAY ASS'Y
PD-II
EA
1
140-PD2-MPLA-UN01-02
PLATFORM ASS'Y
PD-II
EA
1
140-PD2-MPWP-UN01-02
POWER ASS'Y
PD-II
EA
1
41
Unit Q'ty
1
Remark
PARTS NAME : DISPLAY ASS'Y
[PPP-PD0-EDIS-PPPP-P1]
Parts Code
Parts Name
Size
2631-A00-0008-0
VFD CUSHION
43*8*1T(DB-1S)
EA
2
43*8*1T (DB-1S)
6110-PPD-2000-A
PCB-DISPLAY
6110-PPD-2000-0 (PD-II)
EA
1
6110-PPD-2000-0(PD-II)
6224-IS0-6311-0
IC(FIP-DRIVER)
PT6311 QFP
EA
1
U1
6527-ID3-0100-0
RESISTOR-CHIP 1/10W
RR1220P-103D(10K)
EA
7
R2,3,4,5,6,7,8
6527-ID3-0560-0
RESISTOR-CHIP 1/10W
RR1220P-563D(56K)
EA
1
RR1220P-563D(56K)
6712-CHP-0104-0
CHIP CONDENSER
CL21F 104 KBNC
EA
1
CL21F 104 KBNC
7202-D00-052B-0
VFD(FIP)
F-52B (7 DIGIT)
EA
1
V.F.D
7600-STA-1212-0
TACT S/W
12*12(SKHK)DJTA-1103E
EA
3
12*12 TACT S/W
7813-C00-0026-0
SOCKET CONNECTOR
5332-26P LP-Ⅱ
EA
1
HIF-3F-26PA-2.54-DSA
PARTS NAME : MAIN PCB ASS'Y
Unit Q'ty
Remark
[PPP-PD0-EMAP-PPPP-P1]
Parts Code
Parts Name
Size
6100-PPD-2000-A
PCB-MAIN
6100-PPD-2000-0 (PD-II
EA
1
6100-PPD-2000-2 (PD-II)
6200-IPU-9177-0
CPU
uPD78F9177
EA
1
CPU
6205-IS0-2416-0
IC(EEP-ROM)
AT24C164-10SC
EA
1
U5
6210-IS0-7045-0
IC(RESET)
KIA7045F
EA
1
U3
6281-I00-1504-0
CHIP TRANSISTOR
KTA1504 SY
EA
1
Q1
42
Unit Q'ty
Remark
6527-ID0-0510-0
CHIP RESISTOR 1/10W
RR1220P-510D(51Ω)
EA
4
R8,12,L17,19
6527-ID3-0100-0
RESISTOR-CHIP 1/10W
RR1220P-103D(10K)
EA
9
R13,14,15,16,3,4,5,9,10
6527-ID3-1000-0
RESISTOR-CHIP 1/10W
RR1220P-104D(100K)
EA
1
R6,R11
6670-T00-0470-0
INDUCTANCE
470µH
EA
2
L7,8
6704-C25-0330-0
ELECTRIC-CONDENSER
330UF/25V
EA
4
EC6,7,8,9
6712-CAP-0180-0
CHIP CAPACITOR
18PF/50V(CL21C180J)
EA
2
C16,17
6712-CHP-0104-0
CHIP CONDENSER
CL21F 104 KBNC
EA
7
C5,14,19,18,32,33,?
6712-CHP-0471-0
CHIP CONDENSER
CL21F 471 KBNC
EA
6
C35,36,37,38,39,40
6712-CHP-0472-0
CHIP CONDENSER
CL21F 472 KBNC
EA
1
C41
6720-CAP-0474-A
POLYESTER-CONDENSER
0.47UF/63V-J(BOX)
EA
1
C34
6800-F00-0101-0
FERRITE BEADS SMD
MMZ 2012 S102A
EA
2
L16,18
6800-F00-0220-0
EMI FILTER
EFST221YTB(220PF)
EA
5
L4,9,10,11,15
6800-F00-3565-A
EMI BEAD FILTER
BFD-3565 R2
EA
1
L6
7010-ZM0-0500-0
CRYSTAL
5.000MHz
EA
1
7600-STA-1212-0
TACT S/W
12*12(SKHK)DJTA-1103E
EA
1
7808-CLA-0005-A
CONNECTOR(WAFER)
LA1143-05(GOLD)
EA
1
7810-C00-9294-0
CONNECTOR
929400-40(MALE)
EA 0.35
7813-C00-0026-B
SOCKET CONNECTOR
HIF-3F-26PA-2.54-DS
EA
2
7830-W00-0008-0
FLAT CABLE (PD-II POWER)
8(PIN)*190mm
EA
1
POWER WIRE
7830-W00-0016-0
FLAT CABLE (PD-II 병렬)
16(PIN)*80mm
EA
1
병렬통신 WIRE
7830-W00-0026-0
FLAT CABLE (PD-II DISPLAY)
26(PIN)*100mm
EA
1
DISPLAY WIRE
43
12*12 TACT S/W
14/40
PARTS NAME : POWER PCB ASS'Y
[PPP-PD0-EPOW-PPPP-P1]
Parts Code
Parts Name
Size
6140-PPD-2000-A
PCB-POWER
6140-PPD-2000-0 (PD-II
EA
1
6140-PPD-2000-0 (PD-II)
6220-I00-7805-0
IC(REGULATOR)
TA7805S
EA
1
IC2
6220-I00-7912-0
IC(REGULATOR)
LM7912CT
EA
1
IC1
6236-IS0-0014-0
IC(C-MOS)
74HC14
EA
1
U11
6236-IS0-0032-0
IC(C-MOS)
74HC32D
EA
1
U13
6236-IS0-0074-0
IC(CMOS)
74HC74
EA
2
U10,12
6236-IS0-0670-0
IC(C-MOS)
74HC670
EA
2
U14,15
6236-IS0-7403-0
IC(C-MOS)
74HC03D
EA
1
U9
6240-IS0-0232-0
IC(LINE DRIVER)
ICL232CBE(SMD)
EA
1
U1
6290-IBR-0153-0
BRIDGE-DIODE
RB-153
EA
2
BD1,2
6291-IPO-4004-0
POWER-DIODE
1N4004
EA
2
D1,2
6292-IZE-4736-0
ZENER-DIODE
6.8V/1W
EA
2
ZD1,2
6515-CJ3-0300-0
RESISTOR 1/4W
(±5%)
EA
1
R1
6527-ID3-0010-0
RESISTOR-CHIP 1/10W
RR1220P-102D(1K)
EA
2
R19,21
6527-IF0-0003-0
RESISTOR-CHIP 1/10W
FTR 0805 331 FR(3Ω)
EA
1
R23
6527-IF0-0051-0
RESISTOR-CHIP 1/10W
FTR 0805 331 FR(51Ω)
EA
2
R20,22
6550-M05-0472-0
RESISTOR-NETWORK
M5-1-472J
EA
1
6700-C25-0003-0
TANTAL-CONDENSER
3.3uF/25V
EA
1
C12
6704-C25-0100-0
ELECTRIC-CONDENSER
100UF/25V
EA
2
EC4,5
6704-C25-0470-0
ELECTRIC-CONDENSER
470uF/25V
EA
1
EC2
CFR 30K
44
Unit Q'ty
Remark
6704-C25-1000-0
ELECTRIC-CONDENSER
1000UF/25V
EA
1
EC3
6704-C50-0004-0
ELECTRIC-CONDENSER
4.7uF/50V
EA
1
C11
6704-C50-0330-0
ELECTRIC-CONDENSER
330UF/50V
EA
1
EC1
6710-CAP-0104-0
CERAMIC-CONDENSER
0.1UF/25V(50V)
EA
4
C1,2,3,4
6712-CHP-0103-0
CHIP CONDENSER
CL21F 103 KBNC
EA
1
C13
6712-CHP-0104-0
CHIP CONDENSER
CL21F 104 KBNC
EA
12
6712-CHP-0222-0
CHIP CONDENSER
CL21F 222KBNC
EA
2
C20,21
6800-F00-3565-A
EMI BEAD FILTER
BFD-3565 R2
EA
2
L1,2
6830-F00-0040-0
NOISE FILTER
NFB-103S(삼일부품)
EA
1
NFB-103S(삼일)
7801-CLW-0008-0
CONNECTOR(WAFER)
LW 0640-08
EA
1
CON8
7801-CLW-0009-0
CONNECTOR(WAFER)
LW 0640-09
EA
1
CON7
7812-C00-0009-B
D-SUB CONNECTOR
RD9S
EA
1
7812-C00-0025-0
D-SUB CONNECTOR
D25S R-ANGEL(PD-1,LP-2
EA
1
7813-C00-0016-0
SOCKET CONNECTOR
5332-16P
EA
1
45
C7,8,9,10,22,23,24,25,26,
27,28,42
PARTS NAME : BODY ASS'Y
[PPP-PD0-MBOD-PPPP-P1]
Parts Code
Parts Name
Size
1000-A00-0134-0
TRAY
PD-II
EA
1
1030-A00-0208-0
BODY COVER
PD-II
EA
1
1030-A00-0210-0
SIDE BRACKET
PD-II
EA
1
1050-A00-0002-0
SELECT S/W COVER
30*13*0.5T(AL)
EA
1
1100-A00-0056-0
BODY
PD-II
EA
1
1261-A00-0009-0
LIMIT BOLT
M5*0.8*9.2(BSBM 6Kg)
EA
1
1502-A00-0306-0
SCREW-MACHINE(PH)
M3*6
EA
2
1502-MPN-0406-0
SCREW-MACHINE(PH)
M4*6-NI
EA
14
1505-MSU-0410-0
SCREW-MACHINE(TH)
M4*10-SUS
EA
4
1535-MSU-0620-0
BOLT-WRENCH(WA)
M6*20-SUS
EA
4
L/C(BODY , PLATFORM)
1563-A00-0308-0
RIVET
φ3.2*8
EA
2
SPEC PLATE
1810-DB2-0000-0
SPEC PLATE
DB-Ⅱ 내수
EA
1
2610-A00-0002-B
FOOT
M8*37*Φ30 (PD,EP) SUS
EA
4
46
Unit Q'ty
Remark
SELECT SWITCH COVER
BODY COVER ,
POWER ASS'Y,MAIN PCB
DISPLAY ASS'Y ,
SIDE PLATE
PARTS NAME : C/T BOX ASS'Y
[PPP-PD0-MCTB-PPPP-P1]
Parts Code
Parts Name
Size
1260-A00-0015-0
SEALING BOLT
M3*9(CI-3000A,CASTON)
EA
2
7560-PAC-0001-0
AC CORD(ND공용)
(내수.폴란드.필리핀)
EA
1
9100-PD2-0130-0
C/T BOX
무지(PD-II)
EA
1
9102-PD2-4640-0
PAD
460*405 (PD-II)
EA
0
9204-AS0-0013-0
STYROFOAM BOX
PD-II(400*160*100)
EA
2
9301-A00-0003-0
POLY BAG(MANUAL)
170*250*0.05T
EA
1
9303-A00-0004-0
POLY BAG(HEAD)
350*450*0.05T
EA
1
TRAY
9304-A00-0005-A
POLY BAG(SET,HD)
450*580*0.04T(M)
EA
1
PD-II ASS'Y
9400-A00-0046-0
SILICAGEL
10 g
EA
1
9900-A00-0001-0
봉인납
수출용
EA
1
9900-A00-0002-0
SEALING WIRE
300M/ROLL
EA
0
47
Unit Q'ty
Remark
[PPP-PD0-MDIS-PPPP-P1]
Parts Code
Parts Name
Size
1512-A00-0306-0
SCREW-TAPPING(PH)-2
M3*6
EA
4
DISPLAY PCB
1512-A00-0308-0
SCREW-TAPPING(PH)-2
M3*8
EA
2
FRONT CASE
1550-A00-0305-0
WASHER (FLAT)
φ3*φ6*0.5
EA
2
FRONT CASE
2004-A00-0043-0
FRONT CASE
PD-II
EA
1
2004-A00-0044-0
BOTTOM CASE
PD-II
EA
1
2010-A00-0024-0
DISPLAY FILTER
104.9*34.4*1t (SMOG)
EA
1
2200-PD2-1533-0
KEY BOARD PAD
PD-II(15kg) 영공
EA
1
Unit Q'ty
Remark
[PPP-PD0-MDIS-PPPP-P1]
Parts Code
Parts Name
Size
1100-A00-0057-0
PLATFORM
PD-II
EA
1
1502-A00-0415-0
SCREW-MACHINE(PH)
M4*0.7*15
EA
4
PLATFORM RUBBER
1532-MST-0415-0
WRENCH BOLT(ST)
M4*0.7*15-SUS(NYLOK)
EA
4
LIMIT
2022-A00-0003-0
W/L GAGE ASS'Y
φ19*φ21*14.5(BLACK)
EA
1
2600-A00-0080-0
PLATFORM RUBBER
PD-II
EA
4
`2631-A00-0025-0
PLATFORM CUSHION
35*18*1.6t NBR BLACK
EA
6
48
Unit Q'ty
Remark
PARTS NAME : POWER ASS'Y
[PPP-PD0-MPOW-PPPP-P1]
Parts Code
Parts Name
Size
1030-A00-0211-0
TRANS BRACKET
PD-II
EA
1
1502-A00-0305-0
SCREW-MACHINE(PH)
M3*5
EA
2
NOISE FILTER
1502-A00-0306-0
SCREW-MACHINE(PH)
M3*6
EA
3
POWER PCB
1503-A00-0406-0
MACHINE SCREW (WPH)
M4*6
EA
2
TRANS
1550-A00-0305-0
WASHER (FLAT)
φ3*φ6*0.5
EA
2
NOISE FILTER
1552-A00-0300-0
WASHER (OTO)
φ3
EA
1
NOISE FILTER (접지)
7502-PAP-0220-0
POWER TRANS(48)
220V/50~60Hz(AP)
EA
1
POWER TRANS(48)
웰포인
EA
1
AC SOCKET INLET
250mA/250V Φ5 UL,S,VD
EA
2
FUSE
7612-S00-0004-0
7620-S05-0250-0
AC SOCKET CONNECTER
(I
3P-0717 (FUSE))
FUSE
49
Unit Q'ty
Remark

PD-II MANUAL

Transcription

Similar documents

Paymentez User How To Guide en

Sharp Triangle Beads instruction

Help Document Open the URL – www.irctc.co.in Enter your login

Mousekeeping Tip Envelopes

BUYology Warehouse and Discount Stores Deploy the Casio DT

neovisc_reimbursementassistance info_020513

Halloween Party Invitations

February 2016

press release