RM4100 User Guide - American Innovations

Transcription

RM4100 Series
User Guide
Information in this document is subject to change without notice.
© 1999-2015 American Innovations, Ltd. All rights reserved.
American Innovations | www.aiworldwide.com | 12211 Technology Blvd | Austin, TX 78727
Reproduction in any manner whatsoever without the written permission of American Innovations is strictly
forbidden.
Trademarks used in this text: the American Innovations logo and icon are trademarks of American
Innovations, Ltd. The Bullhorn logo and icon are registered trademarks of American Innovations, Ltd.
Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Other trademarks and trade names may be used in this document to refer to either the entities claiming
the marks and names or their products. American Innovations, Ltd. disclaims any proprietary interest in
trademarks and trade names other than its own.
July 1, 2015
Part No. 122195-000, Rev. 3
Contents
Change Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
C HAPTER 1 
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety and Equipment Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ESD Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Bullhorn System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
RM4100 Series Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Required Tools and Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Required Hardware / Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Configuration and Support Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
BATtools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Microsoft .NET Framework. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing Microsoft .NET Framework. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing BATtools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Bullhorn Information Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Contacting Technical Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
C HAPTER 2 
RM4150 and RM4151 Installation . . . . . . . . . . . . . . . . . . . . . 15
RM4150 / RM4151 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Preparing for the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Electrostatic Discharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Ground Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Placement / Mounting Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Mounting the Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Connecting the Dual GPS / GSM Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Connecting the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Connecting Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Connecting the Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Connecting Input Wires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
C HAPTER 3 
RM4100 Series Configuration . . . . . . . . . . . . . . . . . . . . . . . 28
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Configuration Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Disable Synchronization Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Connect the Unit and Start BATtools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Load Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
i
RM4100 Series User Guide
Verify Unit Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Set Up Reporting Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Set Up Interruption and Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Set Up Input Channels and Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Enable Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Set Up Analog Input and Alarm Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
DC or AC Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Instant Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Analog Inputs Graphics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Enable Digital and Accumulator Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Set Up Digital and Accumulator Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Edit Power Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Send Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Create a Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Manage Templates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Upgrade Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Exit BATtools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
A PPENDIX A 
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
A PPENDIX B 
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Replacing the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
A PPENDIX C 
Maintenance & Troubleshooting . . . . . . . . . . . . . . . . . . . . . 57
General Maintenance Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Sealed Lead Acid Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Troubleshooting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
A PPENDIX D
Mercury Relay Customer Advisory . . . . . . . . . . . . . . . . . . . 60
A PPENDIX E
Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
FCC Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
TUV and CE Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Export Control Classification Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
A PPENDIX F
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
ii
Change Notes
The following list identifies product enhancements and updated information included in
the current release of this manual:
•
BATtools 1.5 - BATtools configuration software was updated to version 1.5.
The configuration chapter was updated to reflect the new version. For more
information, refer to Chapter 3, RM4100 Series Configuration.
•
Technical Specifications - update to the RM4100 Switch Output value. Refer
to Appendix A, Technical Specifications.
iii
1
Getting Started
This guide explains how to install Bullhorn® RM4100 Series units, including the RM4150
and RM4151, and to configure the units for service using the BATtools configuration
software. The information applies to the RM4100 Series units that use cellular network
services for communication with Bullhorn Web (http://www.bullhornsys.com).
This guide provides the following information:
•
Chapter 1 - Getting Started
•
Chapter 2 - RM4150 and RM4151 Installation
•
Chapter 3 - RM4100 Series Configuration
NOTE: The RM4100 Series User Guide and other related documentation can be
downloaded in Adobe® PDF format from Bullhorn Web, under the Help menu (Help
menu > Documents). Use Adobe® Reader® version 5 or higher to view the PDF. If needed,
visit the Adobe website at http://www.adobe.com to download a free copy of the
software. Configuration and support software can be downloaded from Help >
Downloads.
1
Safety and Equipment Symbols
WARNING: If the RM4150 or RM4151 is used in a manner not specified by AI, the
protection provided by the equipment may be impaired.
The information in Table 1-1 provides a description of the safety and equipment symbols
present on the outside and inside of the enclosure. Safety symbols alert you to safety
hazards or conditions that have the potential to cause personal injury, death, or
equipment damage. Equipment symbols may indicate a functional state (such as on and
off) and connections (such as a Earth ground terminal).
Getting Started
2
Table 1-1. Safety and Equipment Symbols
Symbol
Description
Caution: Failure to observe this warning may result in personal
injury, death, or equipment damage. A potential risk exists if the
installation instructions are not followed.
Warning: Risk of electrical shock. Failure to observe this warning
may result in personal injury, death, or equipment damage. A
potential risk exists if the installation instructions are not followed.
Earth (ground) terminal: This symbol indicates a protective earth
ground connection is required.
On (Supply): Indicates power is on when the toggle switch is in
the “ON” position.
Off (Supply): Indicates power is off when the toggle switch is in
the “OFF” position.
DC power: Indicates that the input requires DC power.
Both direct and alternating current.
Positive: Indicates a positive input.
Negative: Indicates a negative input.
ESD Precautions
WARNING: To prevent electrostatic discharge (ESD) damage when handling electronic
equipment, always wear an antistatic wrist strap attached to an unpainted, grounded
metal object. Ensure the wrist strap has maximum contact with bare skin.
If an antistatic wrist strap is unavailable, discharge static electricity from yourself and your
clothing by touching a grounded metal object before handling electronic equipment.
Getting Started
3
Bullhorn System Overview
Bullhorn is a wireless telemetry system that provides scheduled and by-exception inbound
reporting for field equipment typically located in remote areas. Data and alarm packets
transmit from remote field locations to your account on the secure, Bullhorn Web (http://
www.bullhornsys.com) using digital cellular or satellite communication networks. You can
quickly determine the status of field equipment anytime using information that posts to
your website account.
Bullhorn provides remote monitoring with full coverage using GSM cellular network, GEOS
satellite (SkyWave-Inmarsat), or LEOS satellite (ORBCOMM) communication networks.
RM4100 Series Overview
RM4100 Series units, including the RM4150 and RM4151, monitor oil and gas assets in
cathodic protection (CP) applications using various communication networks for
communication with the Bullhorn Asset Tracker website.
NOTE: To view a satellite coverage map, log on to Bullhorn Web at http://
www.bullhornsys.com, click Help, and then Coverage Maps in the navigation menu.
RM4100 Series units provide built-in surge protection, rectifier interface, and test point
filtering functionality. The RM4150 and RM4151 measure the output of rectifier current
across shunt resistors. Additionally, the RM4150 and RM4151 support GPS synchronized
current interruption.
The RM4150 supports two (2) configurable digital and five (5) configurable analog inputs
with the following specifications:
•
Input ANALOG CH 1 through ANALOG CH 5 (channels 1 through 5) are isolated
inputs that support analog ±150 V DC, 150 V AC, 4 - 20 mA with external resistor,
or active digital input devices.
•
Input DIGITAL CH 1 and DIGITAL CH 2 are non-isolated inputs (0-24 V DC) that
support digital dry contact closure input devices. DIGITAL CH 1 can also be used as
a pulse count accumulator, and DIGITAL CH 2 can be used as an accumulator
reset.
The RM4151 supports two (2) configurable digital and two (2) configurable analog inputs
•
Input ANALOG CH 1 and ANALOG CH 2 (channels 1 and 2) are isolated inputs that
support analog ±150 V DC, 150 V AC, 4 - 20 mA with external resistor, or active
digital input devices.
Getting Started
4
•
Input DIGITAL CH 1 and DIGITAL CH 2 are non-isolated inputs (0-24 V DC) that
support digital dry contact closure input devices. DIGITAL CH 1 can also be used as
a pulse count accumulator, and DIGITAL CH 2 can be used as an accumulator
reset.
Installation Requirements
Before you install the RM4150 or RM4151 unit, use the following information as a checklist
to ensure a successful installation:
Power Disconnect and Branch Circuit Protection: A customer-supplied,
power disconnect device is required for the unit installation. The power disconnect
device (such as a switch, main circuit breaker, or other type of power disconnect)
should provide an easy and accessible means for removing the main input supply
power source from the unit. Multiple-pole circuit breakers shall interrupt all neutral
and ungrounded connectors of mains supply simultaneously. The power
disconnect device must be clearly marked to identify it as the disconnect device for
the unit. The power disconnect or separate overcurrent protection device should
also provide overcurrent protection in the form of a 20 amp fuse or circuit breaker
suitable for branch circuit protection per local codes and requirements.
Backup Battery: The units should only be used with a 12 V DC, 0.8 AH capacity,
re-chargeable sealed lead acid battery. If you need to replace the battery, please
contact Technical Support for information about purchasing a replacement battery
(American Innovations’ part number 370109-000; manufacturer’s part number PS1208).
NOTE: Refer to Appendix B, Battery Replacement on page 54 for instructions on
changing the backup battery.
Wiring Requirements: For optimum protection from transient voltages (typically,
Channels 1 and 2), all analog inputs must be in their own multi-conductor jacket
cable (such as cable AI part number 211061-000 - Belden 5308UE, or its
equivalent). All cables must have intact outer jackets, except for end cuts. Do not
remove cable jackets as they protect the unit input cable from transient voltages.
Cable insulation should be suited for voltage range of inputs. Cables should be
rated at a minimum of 600 V and 105˚ C.
Input Channel Voltage Levels: All input channels are marked with acceptable
input voltage ranges. Ensure that devices connected to the RM4100 units fall within
the voltages ranges listed next to the channel input connections.
Getting Started
5
Cellular Radio Transmitter: The RM4150 and RM4151 contain a cellular radio
transmitter, and usage may be dangerous in environments such as:
•
Where it can interfere with other electronic devices in environments such as
hospitals, airports, aircraft, etc.
•
Where there is risk of explosion such as gasoline stations, oil refineries, etc.
•
The antenna has to be installed with care in order to avoid any interference
with other electronic devices and has to be guaranteed a minimum distance
from the body (20 cm). In the event that this requirement cannot be satisfied,
the system integrator has to assess the final product against the SAR
regulation.
•
It is the responsibility of the user to enforce the country regulation and the
specific environment regulation.
Earth (ground) terminal: Indicates a protective earth ground connection is
required. The RM4100 Series units require grounding.
•
Antenna Installation: The dual GSM/GPS antenna should be placed outside the
rectifier.
•
Mounting the Enclosure: Place the RM4150 or RM4151 inside the rectifier,
either by placing it on the floor of the rectifier case or by attaching magnets to the
unit and securing to an available area. Choose an area that provides enough room
to easily access the unit or to perform routine maintenance after completing the
installation. Use the information in Figure 1-1 when deciding where to install the
unit.
WARNING: Equipment intended to be mounted on a wall or ceiling shall withstand
a force of four times (4x) the weight of the equipment.
Getting Started
6
4.82 inches
(width)
Front
View
Depth: 2.17 inches
6.73 inches
(length)
Figure 1-1. Enclosure Dimensions
WARNING: Only accessories that meet American Innovations’ specifications may be used
with the RM4150 or RM4151.
Required Tools and Equipment
The following tools and equipment are required for installing and configuring the unit for
service:
•
Antistatic wrist strap
•
Small slotted screwdriver
•
Small Phillips head screwdriver
•
Wire stripper / Wire cutter
•
Voltmeter
•
Adjustable wrench
•
Socket or open end wrench set
•
Waterproof sealing tape
Getting Started
7
•
Silicon adhesive
•
Mounting hardware (appropriate type for mounting surface; supplied by customer)
•
Appropriate tools for preparing the mounting surface for installation (such as a
hand drill and metal, masonry, or wood drilling bit)
•
Installation drawing (provided)
•
Configuration cable (provided; standard mini USB cable typically used with most
digital cameras)
Required Hardware / Software
IBM-compatible computer with the following hardware and software specifications:
•
Pentium® processor or equivalent
•
2 GB RAM (minimum)
•
400 MB free hard drive space (minimum)
•
Spare USB port
•
Microsoft® Windows Vista® Home Premium, Business, or Ultimate with Service
Pack 1 or higher; or Windows 7® Home Premium, Professional, or Ultimate
•
BATtools configuration software (provided)
•
Windows .NET Framework version 4.0 or higher
•
Windows® Internet Explorer® version 8.0 or higher
•
Adobe® Reader® version 6.0 or higher
Configuration and Support Software
To configure the RM4100 Series units for service, you will need the following software
installed on your computer:
•
BATtools
•
.NET Framework
Installation files for BATtools and support software are available through the Bullhorn Web
Help menu > Downloads. BATtools Installation (part number 122201-000) document is
available through the Help menu > Documents.
Getting Started
8
BATtools
BATtools® is a software program you use to set and read the adjustable parameters of the
unit. After installing the unit, you then configure it for service using BATtools software.
BATtools also provides diagnostic tools for checking input channel measurements, RSSI
and Signal Strength level, and transmitting a test packet to confirm communications with
Bullhorn Web.
Using the BATtools software requires that your computer be installed with Microsoft® .NET
Framework version 4.0 or higher.
IMPORTANT: Before installing BATtools, first export all saved templates from BATtools
1.3 (or previous) to your computer using File > Template Management (refer to
Manage Templates on page 49). Then uninstall the previous version of BATtools. After
installing BATtools, import the saved templates.
Microsoft .NET Framework
Before installing BATtools, your computer must be installed with Microsoft® .NET
Framework version 4.0 or higher. Microsoft .NET Framework is a set of software
components that enable your computer to run any software program that has been
developed using Microsoft .NET technology. Microsoft .NET Framework can be
downloaded from your Bullhorn Web account, through the Help menu. Select
Downloads to access the file. For more information about Microsoft .NET Framework,
visit the Microsoft website at the following web address:
http://www.microsoft.com
Installing Microsoft .NET Framework
To install Microsoft .NET Framework:
1
Download the Microsoft .NET Framework executable file from either the Microsoft
website or Bullhorn Web.
2
Navigate to the installation files and double-click the
dotNetFx40_Full_x86_x64.exe file to begin the installation.
3
Follow the installation instructions.
Getting Started
9
Installing BATtools
BATtools is the software used to configure an RM4100 Series unit for service. BATtools can
also be used to view unit information and to create settings templates, which can be used
to configure multiple similar units.
NOTE: Before installing an upgrade to BATtools, first uninstall the previous version.
BATtools requires 44MB of hard disk space.
Complete the following steps to install BATtools:
1
Download BATtools from Bullhorn Web.
2
Navigate to the location of the BATtools file and double-click the BATtools installer
(BATtools_x.xxx.x86.msi) file to begin the installation.
NOTE: The latest version of BATtools that is available on the Help site will have the
current version number in the file name.
3
When the BATtools Setup Wizard window (Figure 1-2) displays, click Next.
Figure 1-2. BATtools Setup Wizard
4
If BATtools is already installed on your computer, the Change, repair, or remove
installation window displays (Figure 1-3). It is recommended that you first
uninstall any previous version of BATtools before installing the latest
version.
Getting Started
10
Figure 1-3. Change, repair, or remove installation
5
If no previous version is installed on your computer, the End-User License
Agreement window (Figure 1-4). Click the I accept the terms in the License
Agreement check box and then Next.
Figure 1-4. End-User License Agreement
6
In the Custom Setup window (Figure 1-5), Click the Create a shortcut for this
program on the desktop check box, if desired. Click Next.
Getting Started
11
Figure 1-5. Custom Setup
7
In the Ready to install BATtools window (Figure 1-6), click Install.
Figure 1-6. Ready to Install BATtools
8
When the installation is complete, click Finish (Figure 1-7).
Getting Started
12
Figure 1-7. Installation Complete
9
To start BATtools, click the BATtools desktop icon
menu and select BATtools.
or click Windows
Start
Bullhorn Information Line
The Bullhorn Information Line is an automated attendant telephone system. It is typically
used when installing units in the field. The system identifies when the last data
transmission (or test packet) was received on your website account for a unit you specify.
Complete the following steps to use the Bullhorn Information Line:
1
Call the Bullhorn Information Line at 866-287-6739.
2
Press 1 to access the packet log when prompted.
3
Use your telephone keypad to enter the unit serial number when prompted. The
unit serial number is included on the bar code label on the side of the unit. It is also
included on the label of the shipping carton. If required, repeat this step to check
another unit.
Getting Started
13
Contacting Technical Services
If you need assistance with the installation or configuration, contact American Innovations
(AI) Technical Services in any of the following ways.
Telephone:
Local: 512-249-3400
Toll-free: 800-229-3404
Email:
[email protected]
Address:
American Innovations, Ltd.
ATTN. Technical Services
12211 Technology Blvd.
Austin, TX 78727
Fax:
512-249-3444
Getting Started
14
2
RM4150 and RM4151 Installation
The procedures in this chapter explain how to install the RM4150 or the RM4151.
WARNING: If the RM4150 or RM4151are used in a manner not specified by American
Innovations, the protection provided by the equipment may be impaired.
RM4150 / RM4151 Overview
The RM4150 and RM4151 (Figure 2-1) are housed in a NEMA-rated weatherproof
enclosure. They are designed primarily for cathodic protection applications and supports
two-way communication with the Bullhorn Web website using the GSM cellular network.
The units support an optional relay connection for GPS-synchronized current interruption.
The RM4150 supports two (2) configurable digital and five (5) configurable analog inputs
•
Input ANALOG CH 1 through ANALOG CH 5 (channels 1 through 5) are isolated
inputs that support analog ±150 V DC, 150 V AC, 4 - 20 mA with external resistor,
or active digital input devices.
•
Input DIGITAL CH 1 and DIGITAL CH 2 are non-isolated inputs (0 - 24 V DC) that
support digital dry contact closure and active digital input devices. DIGITAL CH 1
can also be used as a pulse count accumulator, and DIGITAL CH 2 can be used as
an accumulator reset.
The RM4151 supports two (2) configurable digital and two (2) configurable analog inputs
•
Input ANALOG CH 1 and ANALOG CH 2 (channels 1 and 2) are isolated inputs that
support analog ±150 V DC, 150 V AC, 4 - 20 mA with external resistor, or active
digital input devices.
15
•
Input DIGITAL CH 1 and DIGITAL CH 2 are non-isolated inputs (0 - 24 V DC) that
support digital dry contact closure and active digital input devices. DIGITAL CH 1
can also be used as a pulse count accumulator, and DIGITAL CH 2 can be used as
an accumulator reset.
3
2
1
6
7
Front View
Need New Diagram
4
5
Legend:
4
1 DC Input, Relay Switch Out for
Interruption Verification,and Input
5
Channels (DIGITAL CH1/CH2
and ANALOG CH 1 – CH 5)
6
2 USB Config Port
7
3 GPS and GSM antenna
Input Channels (DIGITAL CH 1 & CH 2 and
ANALOG CH 1 – CH 5): See manual for input
channel specifications.
Switch Out (500 mA max): Relay connection for
for rectifier current interruption. RM4150 supports
mercury or solid state relay.
DC Input 12 V DC = 1.5 A max
Power Switch
Ground
Radio LED
Packet Queue LED
Radio LED: Red when acquiring satellite signal;
green when signal acquired.
Packet in Queue LED: Yellow when waiting to
transmit packet; black when no packets waiting to
transmit.
Figure 2-1. RM4150 and RM4151 Hardware Configuration
16
NOTE: The backup battery is the only serviceable item in the RM4150 and RM4151.
GSM ANTENNA
Port
USB CONFIG Port
GPS ANTENNA
Port
Figure 2-2. RM4150/RM4151 Enclosure Connectors - Antenna and USB Config
POWER Switch
Ground
Figure 2-3. RM4150/RM4151 Enclosure Connectors - Power and Ground
NOTE: Because of the variations in customer's installation and grounding methods, AI
cannot warranty any damage to equipment caused by lightning strikes.
17
Preparing for the Installation
WARNING: Only accessories that meet American Innovations’ specifications may be used
with the RM4150 or RM4151.
WARNING: Turn off power to the rectifier before beginning any wiring installation to the
RM4150 or RM4151.
Use the following items as a checklist prior to installing either the RM4150 or RM4151:
1
For information regarding safety symbols found on the unit, refer to Safety and
Equipment Symbols on page 2.
2
If the unit will be placed or mounted inside the rectifier, refer to Placement /
Mounting Requirements on page 19 for more information.
3
Ensure that the latest version of BATtools and other support software are installed
on the computer you plan to use during the installation. Refer to Configuration
and Support Software on page 8 for more information.
Electrostatic Discharge
Electrostatic Discharge (ESD) can damage electronic components. Provide ESD protection
by wearing an antistatic wrist strap attached to any unpainted metal surface before
opening the enclosure door of the unit or handling electronic parts. If an antistatic wrist
strap is unavailable, discharge static electricity from yourself and your clothing by touching
a nearby metal surface before opening the enclosure door of the unit or handling
electronic components.
Ground Connection
Common practice is to ground the shield of the instrument cable at only one end. Instead,
ground the shield drain wire to a suitable ground point at the source of the signal. This
method is intended to drain off electrically induced voltage levels from external sources in
an effort to ensure the most accurate and stable signal. The shield wire should never be
grounded on both ends. If the signal has unacceptable fluctuation, the system ground
should be repaired or improved.
18
Placement / Mounting Requirements
The RM4150 and RM4151 are designed to be installed inside the rectifier. The list below
identifies conditions to consider before installing the unit. Magnets are included with the
units for mounting on an available surface inside the rectifier.
4.82 inches
(width)
Front
View
Depth: 2.17 inches
6.73 inches
(length)
Figure 2-4. RM4150/RM4151 Enclosure Dimensions
•
If the unit will be placed inside the rectifier, enough room should be available to
place the unit to the back or front of the rectifier case so that it is not directly over
the air vent. Enough room will also be needed for input wires that will be routed
from the unit.
•
If the unit will be mounted inside the rectifier, mounting magnets (Figure 2-5) are
included and can be attached to the unit for easy mounting. See Mounting the
Enclosure on page 21 for more information.
Figure 2-5. Magnetic Disk for Mounting RM4150
19
•
The area should provide enough working space to easily access the unit to wire
inputs, configure the unit for service using the BATtools software, or perform
routine maintenance.
Installation Overview
The following steps provide an overview of a typical installation. The information also
identifies the recommended installation sequence.
1
Determine where to place or mount the RM4150 or RM4151 (page 21).
2
Connect dual GPS/GSM antenna (page 21).
3
Connect incoming power in DC Input connector of RM4150 or RM4151 (page 22).
4
Connect ground wire to rectifier (page 18).
5
Power on the RM4150 or RM4151 (see Figure 2-1 on page 16 for location of
switch).
6
Connect configuration cable (see Figure 2-1 on page 16 for location of USB config
port), and then start BATtools software.
7
If using RM4150 or RM4151to interrupt rectifier current, install and connect a
mercury or solid state relay to the unit (page 24).
8
Connect inputs to RM4150 or RM4151 input channels (page 25).
9
Configure RM4150 or RM4151 for service using BATtools software (Chapter 3,
RM4100 Series Configuration on page 28).
10 If enclosure will be placed (instead of mounted) inside rectifier, place RM4150 or
RM4151 to the rear or front, ensuring that the air vent is left as unobstructed as
possible.
IMPORTANT: Electrostatic Discharge (ESD) can damage electronic components.
Provide ESD protection by wearing an antistatic wrist strap attached to any
unpainted metal surface before opening the enclosure door of the unit or handling
electronic parts. If an antistatic wrist strap is unavailable, discharge static electricity
from yourself and your clothing by touching a nearby metal surface before
opening the enclosure door of the unit or handling electronic components.
20
Mounting the Enclosure
The following section explains how to mount the RM4150 or RM4151 enclosure using the
optional mounting magnets (Figure 2-6).
Figure 2-6. Mounting Magnetic Disks to Back of Unit
Complete the following steps to mount the RM4150 or RM4151 using the four (4)
magnetic disks, screws, and nuts from the accessory kit.
1
Thread a screw through each magnetic disk.
2
Attach a disk to each corner of the unit.
3
Tighten nut onto screw as shown in Figure 2-6.
4
Use a Phillips head screwdriver to tighten screw and secure magnetic disk to unit
case.
5
Mount the enclosure on an available surface inside the rectifier.
Connecting the Dual GPS / GSM Antenna
Complete the following steps to install the dual magnetic-mount GPS and GSM antenna
(Figure 2-7). The dual GPS/GSM antenna is used to synchronize rectifier current
interruption as well as to acquire cellular signal.
21
Figure 2-7. Dual GPS/GSM Antenna Cable
Complete the following steps:
1
Connect the GPS connection end of the dual antenna cable in the connector on the
top of the RM4150 or RM4151 enclosure labeled GPS ANTENNA (see Figure 2-2
on page 17 for location of the connector). The cable for the GPS antenna is labeled.
It also has a red ring at the top of the connector.
2
Connect the GSM connection end of the dual antenna cable in the connector on
the top of the RM4150 or RM4151 enclosure labeled GSM ANTENNA (see
Figure 2-2 on page 17 for location of the connector). The cable for the GSM
antenna is labeled. It also has a blue ring at the top of the connector.
3
Place the antenna on a metal surface, such as the rectifier enclosure. The antenna
will be permanently mounted on the outside of the rectifier.
Connecting the Power Supply
Before beginning the power supply installation, take note of the following safety
specifications:
•
Any line-connected, single-pole switch with a marked OFF position shall be
connected to a TERMINAL or lead intended for connection to the ungrounded
conductor of the supply circuit.
22
•
Overcurrent protective devices shall be connected to the ungrounded supply
connector.
•
A switch or circuit-breaker must be included in the installation.
•
The switch must be suitably located and easily reached.
•
The switch must be marked as the disconnecting device for the equipment.
•
A multiple-pole circuit breaker shall interrupt all neutral and ungrounded
connectors of mains supply simultaneously.
•
Equipment intended for permanent connection to the mains shall have provisions
for connection of a wiring system in accordance with ANSI/NFPA 70, NEC, with CSA
C22.1, CEC, Part I or with both, as appropriate.
Complete the following steps to install a power supply for the RM4150 or RM4151. Refer
to Figure 2-1 on page 16 for location of the power input connector.
Figure 2-8. Power Supply
1
Mount the AC/DC power supply. Typically, the power supply installs inside the
rectifier enclosure.
2
Connect the power supply’s AC Input wires to the AC power source (neutral, white
to white; and hot, black to black).
3
Connect the power supply’s DC Output wires to the DC INPUT connector on the
RM4150 or RM4151 (see Figure 2-1 on page 16 for location of connector).
NOTE: The RM4150/RM4151 make a clicking sound after turning on the power
switch. This is a normal function and indicates the unit is polling input channels.
23
Connecting Ground
Complete the following steps to ground the RM4150 or RM4151 to the rectifier frame.
Refer to Figure 2-1 on page 16 for the location of the ground connection on the unit.
1
Connect ground wire (attached to the unit) to rectifier frame using spade
connectors (Figure 2-9).
Figure 2-9. Ground Wire with Spade Connectors
2
If necessary, use I-beam clamp to secure spade connectors. Remember to remove
any paint where the clamp will be attached to the frame (Figure 2-10).
Figure 2-10. I-beam Ground Clamp and Spade Connectors for Ground
Wire
Connecting the Relay
NOTE: Please see the Mercury Relay Customer Advisory in Appendix D on page 60
regarding the manufacturer’s published limitations on mercury relays.
Complete the following steps to install the relay (mercury or solid state relay).
1
Identify the most suitable location and connection points for installing the relay.
This may be in the secondary AC circuit, the DC positive (+) output, or DC negative
(–) output.
24
2
Mount the relay on a suitable surface.
If you are installing the mercury relay, the relay functions with a contact in a pool of
mercury, therefore making orientation of the relay important. Ensure that the relay
is mounted in a vertical position (within 10 degrees from vertical) so that the
writing on the relay is upright and readable.
3
Connect the appropriate cable for the load being switched, from the copper
connectors on the bottom and top of the relay, to the connections points used
earlier in step 1.
4
Connect relay wires in the SWITCH OUT connector on the unit (positive to
positive; negative to negative). See Figure 2-1 on page 16 for location of
connector.
Connecting Input Wires
WARNING: Ensure that power to the rectifier has been turned off before wiring to unit.
Complete the following steps to connect input wires to the RM4150 or RM4151.
American Innovations recommends using AI part number 211061-000 (Belden 5308UE), or
equivalent, for wiring inputs.
1
Connect your rectifier input wires to the RM4150 (DIGITAL CH 1 and DIGITAL CH
2 and ANALOG CH 1 through ANALOG CH 5 in Figure 2-11) or to the RM4151
(DIGITAL CH 1 and DIGITAL CH 2 and ANALOG CH 1 and ANALOG CH 2 ).
Refer to RM4150 / RM4151 Overview on page 15 for unit input specifications.
25
Figure 2-11. RM4150 Inputs - Side View
NOTE: To ensure a clean stable reading, keep field wiring as short as possible and
use shielded twisted pair wire such as Alpha 2463C.
2
Dress input wires inside the rectifier.
3
Connect unit input wires to the output terminals of your rectifier.
WARNING: If wires are to be buried or covered, conduit must be used to protect
wires.
4
If rectifier is turned off, turn ON to restore power to field wiring.
5
Continue with Chapter 3, RM4100 Series Configuration on page 28 to configure
the RM4150 for service.
26
6
After configuring the RM4150 or RM4151:
a
Remove USB cable and re-attach USB port cover.
b
If the unit is to be placed (not mounted) inside the rectifier, position the unit to
the front or rear of the rectifier case so that the unit covers only a minimal
amount of the rectifier air vent.
27
3
RM4100 Series Configuration
Introduction
Information in this chapter explains how to configure the RM4100 series units, such as the
RM4150 and RM4151, for service using the BATtools configuration software. Refer to
Installing BATtools on page 10 for instructions.
After configuring the RM4100 Series unit, the unit information and settings can be
accessed through the Bullhorn Web website (http://www.bullhornsys.com).
Refer to Glossary for definition of terms used in this section.
Configuration Overview
The configuration process includes the following tasks:
1
If present, disable synchronization software, such as Microsoft®
ActiveSync®(page 29).
2
Connect the unit to your computer and start BATtools (page 29).
3
Load a template if one is available for the unit type you plan to configure
(page 30). If using a template, skip to step 11.
4
Verify unit and hardware information (page 31).
5
Set up reporting settings (page 33).
6
Set up interruption settings (page 34).
7
Enable analog inputs (page 37).
28
8
Set up analog input and alarm settings (page 38).
9
Enable digital and accumulators (page 43).
10 Set up digital and accumulator settings (page 43).
11 Set battery installation date and type (page 46).
12 Send a message to test communication (page 47).
13 Upgrade firmware (optional) (page 50).
14 Save settings in a template (page 48).
Disable Synchronization Software
If you use a synchronization software to synchronize a mobile device with your computer,
temporarily disable the software before starting BATtools.
If you use Microsoft ActiveSync to synchronize the Allegro field computer with your
computer, complete the following steps to temporarily disable the software:
1
Click Start > Programs > Microsoft ActiveSync .
2
Click File > Connection Settings . If enabled, click to remove the check mark and
disable COM port, USB, and network options.
3
Click OK to close Connection Settings. Click File > Close to exit ActiveSync.
Connect the Unit and Start BATtools
1
Connect the configuration cable in the USB port of your computer. Connect the
other end of the cable in the USB CONFIG port on the unit.
2
Power on the unit.
3
Start BATtools. Refer to Configuration and Support Software on page 8 for
instructions on installing BATtools and its support software.
4
The Unit Overview window displays (Figure 3-1). Click
Refresh to read unit
settings and verify the unit and BATtools software are communicating. If so, the
informational fields, such as Serial and Unit SIM, will populate.
RM4100 Series Conf iguration
29
Figure 3-1. BATtools Unit Overview Window
At start up, a packet is sent to your Bullhorn Web account. You can view the details on the
Unit Detail page (Figure 3-2).
Figure 3-2. Start Up Packet Details on Bullhorn Web
Load Template
If a template is available for the unit type you plan to configure, load the template using
the following steps:
1
Click File > Load Template (Figure 3-3).
30
Figure 3-3. Load Template
2
From the Apply Template window, select a template that has been previously
saved in BATtools from the list shown in the pull-down menu (Figure 3-4).
Figure 3-4. Select Template
3
Click Apply.
4
OR click Import to locate a template. Locate and select the template (should have
the extension .bht) and then click Open.
5
Click Apply. The settings are applied to the unit.
6
Verify unit information, then continue with Edit Power Information.
Verify Unit Information
Use the following steps to check unit and hardware information:
31
1
Click the name of the unit to view Unit Information, Transmission
Information, Interrupter Information, GPS Information, and Power
Information (Figure 3-5).
Figure 3-5. Unit Overview
2
Click
Hardware Info to view Unit, Radio, GPS, and Firmware Versions
(Figure 3-6).
Figure 3-6. Hardware Info
32
Set Up Reporting Schedule
Reporting schedule determines when and how often channel measurements transmit to
your website account.
Complete the following steps to schedule reports:
1
Click
Reporting (Figure 3-7).
Figure 3-7. Reporting
The Reporting window displays (Figure 3-8):
Figure 3-8. Reporting Settings
2
Enter a value in the UTC Offset field. You can also click the up and down arrows to
adjust the time. For more information about UTC, visit the Naval Oceanography
Portal website at http://aa.usno.navy.mil/faq/docs/UT.php.
3
Select either On or Off in Schedule Reporting field.
4
Select either Repeat or Day of Month in Reporting Mode field.
a
If you selected Repeat for Reporting Mode:
33
1) Enter a time in Time of First Report to set when the first report will be
sent. For example, typing a 2 will display 2:00 AM .
• Time defaults to AM. To change to PM, click on AM and type a P.
• To change hour or minutes, click on the number and type over with new
time.
2) Select a value in the Repeat Interval drop down field to set the amount
of time (one hour to 30 days) the unit will wait between reports.
b
If you selected Day of Month for Reporting Mode , enter a value in the Day
of Month 1 field (Figure 3-8). You can also click the up and down arrows to
adjust the value. Repeat, as needed, for Day of Month 2, Day of Month 3 ,
and Day of Month 4 fields.
NOTE: The days selected for Day of Month 1 - 4 must be in ascending order, and
a latter day cannot be set before an earlier day.
5
6
Enter a time in Time of Day field. For example, typing a 2 will display 2:00 AM .
a
Time defaults to AM. To change to PM, click on AM and type a P.
b
To change hour or minutes, click on the number and type over with new time.
Click
Save to save settings or
Cancel to clear all fields.
Set Up Interruption and Interference
Complete the following steps to set up the RM4150 or RM4151 interruption settings:
1
Click
Interruption (Figure 3-9).
Figure 3-9. Interruption
34
The Interruption Settings window displays (Figure 3-10):
Figure 3-10. Interruption and Interference Settings
2
Click the down arrow next to Interrupter Mode and select one of the following
options: Off, Daily, Start/Stop , Continuous, or Always Off.
a
If you selected Daily interrupter mode, enter a Start Time and a Stop Time:
1) Enter a time in the text field. For example, typing a 2 will display 2:00 AM .
• Time defaults to AM. To change to PM, click on AM and type a P.
• To change hour or minutes, click on the number and type over with new
time.
b
If you selected Start/Stop interrupter mode:
1) Click the down arrow in the Start Date and Stop Date fields to display a
calendar; select a date to start and stop the interruption.
2) Enter a Start Time and a Stop Time:
i)
3
Enter a time in the text field. For example, typing a 2 will display 2:00
AM .
•
Time defaults to AM. To change to PM, click on AM and type a P.
•
To change hour or minutes, click on the number and type over with
new time.
Set up interrupter On/Off Times to indicate how many seconds the interrupter
switches current on and off.
35
NOTE: On/Off Times can be set in 0.1 second increments, with the minimum cycle
or period time being 0.2 seconds (on for 0.1 second/off for 0.1 second).
4
5
6
a
Enter the number of seconds in the On Time field to specify the amount of
time current is switched on. You can also click the up or down arrow to
increase or decrease the number of seconds.
b
Enter the number of seconds in the Off Time field to specify the amount of
time current is switched off. You can also click the up or down arrow to
increase or decrease the number of seconds.
Set up Output & Synchronization:
a
Output Mode: If using a normally closed relay, click Normally Closed . If
using a normally open relay instead, click Normally Open.
b
Sync Mode: If the interruption should start with the off cycle, click the option
Off/On . If the interruption should start with the on cycle instead, click the
option On/Off.
Set up Interference Mode:
a
To enable Interference Mode, select Enabled from the Interference Mode
field.
b
Enter the total number of units that will be included in the group in the
Number of Units field. This number must be at least 2.
c
Enter a value for this unit in the My Number field. This number must be less
than or equal to Number of Units.
d
Enter a value (in seconds) for Delay.
Click
Set Up Input Channels and Alarms
Based on the type of input device connected to the input channels of the unit, use the
procedures in the following sections to set up channels and alarms:
•
Enable Analog Inputs
•
Enable Digital and Accumulator Inputs
36
Enable Analog Inputs
Complete the following steps to enable and define the inputs for Analog CH1 - CH5. Refer
to Technical Specifications on page 52 for channel ratings.
1
Click
Analog Inputs (Figure 3-11).
Figure 3-11. Analog Inputs
The Analog Inputs window displays (Figure 3-12):
Figure 3-12. Analog Inputs Enable/Disable
2
Select a value for each channel that will be used or select Disabled for unused
channels.
a
DC Enabled (CH1 - CH5) - input is DC.
b
Instant Off (CH3) - measures reading at Instant Off.
c
DC & Instant Off (CH3) - the input is DC, and the channel will measure
Instant Off.
3
d
AC Enabled (CH4 and CH5) - the input is AC.
e
AC & DC Enabled (CH4 and CH5) - the input is both AC and DC.
Click
37
Set Up Analog Input and Alarm Settings
Edit the input and alarm settings for each analog channel that you enabled in the previous
section. Refer to Appendix F, Glossary for definitions of fields and terms.
DC or AC Enabled
1
Click the
next to the channel name, such as Analog CH1 or Analog CH4, to
expand, if not already expanded.
2
Click the input name (for example,
channel name (Figure 3-13).
DC_AMPS,
DC_VOLTS) under the
Figure 3-13. Analog Inputs
The DC (or AC ) Channel settings window displays (Figure 3-14):
38
Figure 3-14. DC/AC Channel Input and Alarm Settings
3
Optional: Enter a name for the input in the Input Name field. This name will
display in the navigation tree.
4
Select either Volts or Milli-Volts in Input Type field.
5
Enter the maximum voltage value in Input Maximum Value field. You can also
use the up and down arrows to change the value.
6
Enter the minimum voltage value in Input Minimum Value field. You can also use
the up and down arrows to change the value.
NOTE: The Input Maximum Value must be greater than the Input Minimum
Value.
39
7
Enter a label for the Scaled Label. The value you enter here will display in the
Settings Preview area of the window, as well as the Unit Overview window,
under the dial icon (for DC enabled channels only). The value will also be used with
Scaled Maximum Value and Scaled Minimum Value.
8
Enter the maximum scaled value in Scaled Maximum Value field. You can also
use the up and down arrows to change the value.
9
Enter the minimum scaled value in Scaled Minimum Value field. You can also use
the up and down arrows to change the value.
NOTE: The Scaled Maximum Value must be greater than the Scaled Minimum
Value.
10 Enter a value for Alarm Persistence . Entering a zero (0) disables persistence.
11 Select either Enable or Disable for High Alarm Enable.
12 If enabling a high alarm, also enter the following settings:
a
Enter a value for the High Alarm Threshold .
b
Enter a value for the High Alarm Deadband . This value will display on the
analog channel dial icon shown in the setup window (Figure 3-15) as well as on
the Unit Overview window. The yellow and orange sections of the dial mark
the deadband value (2.00) that was entered in the High Alarm Deadband
field. The deadband values “buffer” the High Alarm Threshold value of 45.
40
Figure 3-15. Deadband for High and Low Alarm
13 Select either Enable or Disable for Low Alarm Enable .
14 If enabling a low alarm, also enter the following settings:
a
Enter a value for the Low Alarm Value.
b
Enter a value for the Low Alarm Deadband . This value will display on the
analog channel dial icon shown in the setup window (Figure 3-15) as well as on
the Unit Overview window. The yellow and orange sections of the dial mark
the deadband value (2.00) that was entered in the Low Alarm Deadband
field. The deadband values “buffer” the Low Alarm Value of 5.33.
15 Select either Enable or Disable for Transmit Alarm Clear. Enabling this setting
will transmit a packet to your Bullhorn Web account when the unit is out of alarm.
41
16 Click
Instant Off
1
Click the
next to Analog CH3 to expand, if not already expanded.
2
Click
3
Enter a value (in milliseconds) in the IOX Edge Offset field to set how long the
unit will wait before taking a measurement after power from the rectifier has been
turned off.
4
Click
Instant Off under the channel name.
Analog Inputs Graphics
After you configure the analog inputs, a graphical representation of the settings will
display for each enabled input (except Instant Off) on the Unit Overview window. The
graphic includes a dial that shows the Scaled Maximum Value, along with the Low
Alarm/Deadband and High Alarm/Deadband (see also Figure 3-15, page 41). The graphic
also displays the current reading and input value. The graphic can also be seen when you
Analog CH5) or in the Settings Preview of the input settings
click on an input (
window (Figure 3-16).
Figure 3-16. Analog Inputs Graphics
42
Enable Digital and Accumulator Inputs
Complete the following steps to enable or disable Digital CH1 and CH2. Refer to Technical
Specifications on page 52 for channel ratings.
1
Click
Digitals & Accumulators (Figure 3-17).
Figure 3-17. Digitals & Accumulators
The Digitals & Accumulators window displays (Figure 3-18):
Figure 3-18. Digitals & Accumulators Enable/Disable
2
Select Enable for a channel that will be used or Disabled for an unused channel.
3
Click
Set Up Digital and Accumulator Inputs
Edit the digital and accumulator settings for each digital channel that you enabled in the
previous section. Refer to Appendix F, Glossary for definitions of terms.
1
Click the
expanded.
next to
Digitals & Accumulators to expand, if not already
2
Click the channel name. For example,
Digital CH1 (Figure 3-19).
43
Figure 3-19. Digital CH1
The Digital Settings / Accumulator Settings window displays (Figure 3-20):
Figure 3-20. Digital Settings / Accumulator Settings
3
Enter a value (in milliseconds) in Input Persistence field. You can also use the up
and down arrows to change the value.
4
Select either Enable or Disable for High (Open) Alarm.
5
Select either Enable or Disable for Low (Closed) Alarm.
6
If the channel will be used as an accumulator, complete the following steps:
a
Enter a value in Accumulator Count field. You can also use the up and down
arrows to change the value.
b
Select a Reset Mode .
44
c
If you selected Reset on Alt Channel Edge for the Reset Mode, select either
Reset on Falling Edge or Reset on Rising Edge in the Alt Channel Edge
field.
d
If you selected Reset on Count , enter a value in Reset Accumulator At (the
value, when reached, that resets the accumulator) and Reset Accumulator
To (the count at which the accumulator will be reset) fields (Figure 3-21). You
can also use the up and down arrows to change the value.
Figure 3-21. Reset Accumulator At and Reset Accumulator To
7
e
Select either Enable or Disable for Accumulator Alarm to have an alarm
sent when the accumulator reaches the value that is set in the Accumulator
Alarm Value (step f, below).
f
If you enabled the Accumulator Alarm, enter a value in Accumulator
Alarm Value field. You can also use the up and down arrows to change the
value.
Click
The Unit Overview window will display a graphic (Figure 3-22) for the digital
channels that you enabled. Yellow indicates a High input state; gray indicates a Low
input state. The graphic also contains accumulator count and alarm settings.
45
Figure 3-22. Digital Channel Graphic
Edit Power Information
Complete the following steps to edit battery information:
1
Click
Power (Figure 3-23).
Figure 3-23. Power
The Power window displays (Figure 3-24):
46
Figure 3-24. Power Settings
2
Click the down arrow in Battery Install Date field to open a calendar (Figure 325).
Figure 3-25. Installation Calendar
3
Select a date.
4
To clear the field, click Clear.
5
Select a battery type in Battery Type field.
6
Click
Send Message
Complete the following steps to send a message to the Bullhorn Asset Tracker website
account:
NOTE: At start-up, the unit will send a Startup packet to the Bullhorn Web account.
1
Click Action > Send Message .
47
2
Select either Profile or Test from the Select Command field (Figure 3-26). Both
Profile and Test command will send the current values of the data points.
Figure 3-26. Send Message - Select Command
3
Click Send .
A confirmation window displays briefly.
A packet is sent to your Bullhorn Web account with current data point information.
View the packet on the Unit Detail page, under the Incoming Packets tab. The
example below shows an incoming Test message from the unit.
Figure 3-27. Test Message on Incoming Packets in Bullhorn Web
Create a Template
After configuring a unit, the settings can be saved in a template. You can use the template
to set up another unit of the same type.
48
Complete the following steps to create a new template:
1
Click File > Create Template.
2
Enter a name for the new template (Figure 3-28).
Figure 3-28. Create Template
3
Click Save.
Manage Templates
Saved templates can be exported to your computer or deleted from BATtools.
Complete the following steps to export or delete a template:
1
Click File > Template Management .
2
Select a template (Figure 3-29).
Figure 3-29. Template Management
3
To export the template as a Bullhorn Template (.bht) file, click Export.
4
Select a destination for the file and then click Save .
NOTE: This type of file can be imported when using the File > Load Template,
Import function (refer to Load Template on page 30).
5
To delete the template, click Delete .
49
Upgrade Firmware
Available upgrades to the RM4100 Series firmware can be applied to the unit. Complete
the following steps to upgrade firmware:
NOTE: The latest firmware can be downloaded from the Bullhorn Web (Help >
Downloads). Download the latest firmware before completing the steps in this section.
1
Click Action > Upgrade Firmware .
2
Click Browse to search for the firmware file. This file should have the extension
.bhf.
a
Open the firmware file.
b
Click Upgrade .
c
To verify that the firmware was updated, click the name of the unit in the
navigation pane. The Firmware Version is displayed in the Unit Information
section of the Unit Overview window (Figure 3-30). The firmware version
number should match the version you selected in step 2 .
Figure 3-30. Firmware Version
Exit BATtools
1
Click File > Exit .
2
Disconnect the configuration cable from the unit and your computer.
50
3
Re-enable any synchronization software previously disabled.
The configuration is now complete.
51
A
Technical Specifications
This appendix includes technical specifications for the RM4150 and RM4151.
•
•
•
Environmental conditions:
•
Outdoor use only.
•
Maximum altitude: 3,000 m.
•
Temperature range: -30˚ C to +70˚ C.
•
Maximum relative humidity: 95% at 45˚ C, decreasing linearly to 45% at 70˚ C.
•
Minimum temperature rating for PCB (printed circuit board): at least 105˚ C.
DC Input:
•
Voltage: 10 - 14 V DC.
•
Current: 1.5 A DC max.
AC Input (requires optional external AC-DC power supply):
•
Voltage: 100 - 240 V AC.
•
Current: 0.15 - 0.3 A AC.
•
Frequency range: 50 - 60 Hz.
•
Battery: Power Sonic PS-1208, 12 V rechargeable, sealed lead acid battery.
Specified battery shall be used.
•
Switch Output: 10 - 14 V DC, 0.5 A DCmax source current.
52
•
Digital Ch1 and Ch2: Dry contacts or 0 - 24 V DC input voltage.
•
Analog Inputs:
•
RM4150 Analog Ch1 - Ch5: ±150 V DC, 150 V AC input voltage, CAT II rating.
•
RM4151 Analog Ch1 and Ch2: ±150 V DC, 150 V AC input voltage, CAT II
rating.
•
Scan Rate (accumulator): input sampled 20 times per second, with a minimum
pulse width of 250 ms.
•
Interconnect cable: Belden 5308UE; 300 Vrms; rated FT4; 600 V - 105˚ C, or
equivalent.
Technical Specif ications
53
B
Battery Replacement
The RM4150 and RM4151 units should only be used with a 12 V DC, 0.8 AH
capacity, re-chargeable sealed lead acid battery. If you need to replace the battery,
please contact Technical Support for information about purchasing a replacement
battery (American Innovations’ part number 370109-000; manufacturer’s part
number PS-1208).
The procedures in this appendix explain how to replace the 12 volt lead acid battery in the
RM4150/RM4151.
IMPORTANT: Turn off power from field wiring before performing either the battery
replacement or fuse replacement procedures.
Replacing the Battery
WARNING: To prevent electrostatic discharge (ESD) damage when handling electronic
equipment, always wear an antistatic wrist strap attached to an unpainted, grounded metal
object. Ensure the wrist strap has maximum contact with bare skin. If an antistatic wrist
strap is unavailable, discharge static electricity from yourself and your clothing by touching
a grounded metal object before handling electronic equipment.
1
Turn OFF the power to the unit.
2
Turn OFF power to remove power from field wiring.
54
3
Disconnect input channel wiring.
4
Use a Phillips head screwdriver to loosen the four (4) screws securing the cover
(Figure B-1). You do not need to remove the screws.
Figure B-1. RM4150 Faceplate
5
Set aside cover.
Battery Replacement
55
6
Disconnect the battery (Figure B-2, highlighted in yellow).
Figure B-2. Disconnect Battery
7
Lift battery from unit.
8
Replace with new battery.
9
Connect new battery.
10 Replace unit cover.
11 Tighten cover corner screws.
12 Reconnect input channel wiring.
13 Turn power ON to restore power to field wiring.
14 Turn ON the power to the unit.
The battery replacement is now complete.
Battery Replacement
56
C
Maintenance & Troubleshooting
This appendix provides general maintenance tips and troubleshooting guidelines for the
RM4100 Series. If you experience problems with the equipment or BATtools software and
are unable to resolve a problem using the following information, contact Technical
Support for assistance at 512-249-3400 (or toll-free at 800-229-3404).
General Maintenance Tips
NOTE: The only serviceable item in the RM4150/RM4151 is the battery.
Sealed Lead Acid Battery
•
Use BATtools software or a voltmeter to monitor the battery voltage level. The
battery is considered low at 11.0 volts and dead at 10.5 volts.
•
Bullhorn units monitor the voltage level when the unit is on or transmitting. If the
unit detects a low battery, the battery and charging system should be checked as
soon as possible, and the battery replaced when required. Refer to Appendix B,
Battery Replacement on page 54 for instructions on how to change the internal
battery.
•
The battery requires a charger to keep it charged, such as the AC/DC charger
provided by AI.
57
Troubleshooting Guidelines
Table C-1. Troubleshooting Guidelines
Description
Action
BATtools software cannot find the
unit.
• Verify the configuration cable connects
securely to the unit and computer.
• Verify the power switch is on (see Figure 2-1,
on page 16). The front LED lights will be lit if
power is going to the unit.
Unit does not communicate or
transmit.
• Verify the power switch is on (see Figure 2-1,
on page 16). The front LED lights will be lit if
power is going to the unit.
• Verify the dual antenna cable is connected
securely to the unit (see Connecting the
Dual GPS / GSM Antenna on page 21).
• Use the BATtools software to verify the
battery voltage level is above 11.0 volts (see
Verify Unit Information on page 31). If not,
check the battery charging system and
replace the battery, if required.
• Use the BATtools software to verify the RSSI
level is sufficient for transmissions (see
Figure 3-6, on page 32). Based on the unit
type, verify the RSSI meets the following
qualifications:
• GSM Digital Cellular: unit requires an
RSSI greater than -110dB. RSSI is on a
negative scale. Numbers closer to zero
indicate a stronger signal.
• Use the BATtools software to send a
message to confirm communication with
the Bullhorn Web(see Send Message on
page 47). If the message does not show up
in the Incoming Packets table in Unit
Detail on the website within 10 minutes, call
the Bullhorn Information Line or contact
Technical Support (see Contacting
Technical Services on page 14) to confirm
the website received the message from the
unit.
Unit is not reading input channel.
Use the BATtools software to verify the
channel is enabled for service (see Set Up
Input Channels and Alarms on page 36).
58
Table C-1. Troubleshooting Guidelines (continued)
Description
Action
Channel reading has incorrect polarity.
Verify positive/negative input wires are
connected correctly in the input channel
terminal (see Connecting Input Wires on
page 25). Positive input wire connects in
positive terminal; negative input wire connects
in negative terminal.
59
D
Mercury Relay Customer Advisory
The information in this section is intended to notify American Innovations (AI) customers
of the manufacturer’s published limitations on mercury relays.
Customers primarily purchase mercury relays for use with current interrupters. Current
interrupters provide great programming flexibility to enable customers to use a wide
variety of interruption cycles.
AI supplies mercury relays from a variety of respected and reliable vendors including MDI
and American Electronic Components (AEC). These manufacturers publish expected relay
lives of 3 to 6 million cycles depending upon the type of relay selected. AEC, the
manufacturer of Durakool relays, indicates that relay life will be significantly shortened at
rates exceeding 1,500 cycles per hour. MDI recommends no more than 900 cycles per hour.
Depending upon the interruption cycle chosen by the customer, it is possible to exceed
the manufacturer’s recommendation, which would result in a likely reduction of service life.
As an example, customers who elect to use mercury relays to interrupt at 1 cycle per
second will generate 3600 cycles per hour. Customers should consult the manufacturer’s
documentation to select the appropriate relay for the application.
Durakool information can be found on the AEC web page at the following address:
http://www.aecsensors.com/html
In the Durakool documentation, the following two situations are explained that may
impact the current carrying capacity of the relay: 1) cycle rate and 2) voltage values. The
sizing tables indicate a methodology for determining the maximum amperage that can be
carried depending upon the cycle rate. An additional de-rating table for mercury relays is
provided for those instances where voltage in excess of 48 V DC is being interrupted.
When selecting relays, customers should be aware of both of these de-rating tables to
choose the best relay for the application.
60
To avoid depolarization of the CP system, the mercury relays that AI sells are of the
normally closed variety. It is possible that a normally closed relay will fail at the end of its
life in the open position due to a malfunction of the spring mechanism which drives the
plunger/contacts into a normally closed position. If this occurs, a depolarization situation
would result. AI has the following two recommendations:
1
Customers using mercury relays should consider periodic replacement of these
relays based upon engineering estimated life via a preventive maintenance
program to reduce the likelihood of an open circuit failure.
2
If fast cycle operation is common, AI recommends a solid state relay for maximum
life and reliability.
Although most interrupters are capable of being programmed for faster interruption
cycles, AI recommends that customers not exceed 900 cycles per hour (or a cycle time of
less than four seconds) and will not warranty devices that are utilized in this manner. AI
adds a serial number to relays that is supplied that we supply to enable the tracking of the
shipment date. The approximate age of the relay may be used to assist AI in return
material response, failure analysis, and warranty claims. Manufacturers will be consulted to
help determine failure cause and to advise customers that warranties may not be honored
if it is deemed that the mercury relay is used outside of recommended parameters.
If you have questions or need additional information, please contact Technical Support
(800-299-3404). Office hours are Monday–Friday, 8:30–5:00 Central Time.
Mercury Relay Customer Advisory
61
E
Regulatory Notices
FCC Requirements
The following FCC requirements are met by the products described in this guide.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment in an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
62
TUV and CE Certification
RM4100 Series units have been tested and certified by TUV SUD, a Nationally Recognized
Testing Laboratory (NRTL). The RM4100 Series units meet or exceeds the quality and safety
requirements for UL 61010-1:2004 and CAN/CSA-C22.2 61010-1:2004. The RM4100 Series
is also CE certified. The TUV test mark assigned to the RM4100 Series, as well as the CE
symbol, are shown below.
Export Control Classification Number
The Export Control Classification Number (ECCN) assigned to the BATtools software by the
U.S. Bureau of Industry and Security (BIS) is as follows:
•
ECCN Classification:
•
ECCN Code:
No Classification
EAR99 or NLR
Regulatory Notices
63
F
Glossary
The following information is an alphabetical list of technical terms and BATtools fields
identified in this manual.
Table F-1. Glossary of Technical Terms
Term
Definition
Alarm Persistence
In BATtools, the amount of time, in milliseconds, that the
unit will wait before re-sending an alarm.
BATtools
Software program used to configure a unit for service
and view status information such as channel
measurements, battery voltage level, and RSSI.
Bullhorn Control Module
Firmware version of the RM4100 Series unit. The version
number can be found on the BATtools Hardware Info
window.
Deadband
Deadband applies hysteresis to low and high alarm
values. It is an area of equal value above and below the
alarm values. The deadband acts as a buffer: when the
input voltage passes below the deadband area, this is
the alarm point that triggers a low alarm transmission;
likewise, when the input voltage passes above the
deadband area, this is the alarm point that triggers a
high alarm transmission. In BATtools, the deadband is
identified on the dial icon for each channel in either
yellow or orange (see Figure 3-15, page 41).
64
Table F-1. Glossary of Technical Terms (continued)
Term
Definition
Firmware Version
Version number of the firmware currently installed on
the unit.
GPS
Global Positioning System. Global navigation satellite
system that provides location and time information
when three or more GPS satellites are in view.
GPS Information
Information field showing unit GPS and elevation
coordinates. Antenna Status applies to the magneticmount antenna.
IMEI
International Mobile Equipment Identity. Unique
number assigned to the digital cellular radio by the
manufacturer for identification purposes.
Interference Mode
The ability to test for interference on a pipeline from
other sources (see Set Up Interruption and
Interference on page 34).
IOX Edge Offset
For Instant Off setting in BATtools, the amount of time
(in milliseconds) that the unit waits before taking a
measurement after power from the rectifier has been
turned off.
LED
Light Emitting Diode.
Model #
The model number of the radio installed on the unit.
Found on BATtools Hardware Info window.
Output Mode
The state of the relay; either Normally Closed or
Normally Open. Found on BATtools Interruption
window.
Glossary
65
Term
Definition
Persistence
Persistence (Alarm Persistence, Input Persistence) is the
number of samples an input channel must complete
while in a particular state before that state is recognized
as an alarm. Persistence is an optional filter. The purpose
of the filter is to prevent short spurious noise pulses
from triggering an alarm. If the input channel goes out
of alarm during the polling cycle, the unit resets and
does not transmit an alarm. When Persistence is set to
zero (0), no filter is applied and the alarm state is
recognized immediately.
For example, if an input channel is set up with a high
alarm and a persistence value of 5, the input channel
must complete 6 samples in a high state before it is
recognized as a high alarm.
Polling Cycle
Polling cycle refers to how often the unit scans or reads
input channels. BATtools scans input channels at regular
intervals based on the hardware sampling of the unit
type.
Radio ISN
Radio Identification Serial Number. The SkyWave
satellite terminal and unit ship from the factory as a
matching pair. Both are assigned the same ISN at the
factory for identification purposes. Also see Unit ISN.
Refresh
Clicking
Refresh in BATtools updates unit
information.
Reporting
Scheduled data transmission at regular time intervals.
Reset on Falling Edge
In BATtools, this field selection for Alt Channel Edge
(Accumulator Settings - Digital inputs) defines that the
accumulator will be reset to 0 when Digital CH2’s Input
State changes to Low (see Set Up Digital and
Accumulator Inputs on page 43).
Reset on Rising Edge
In BATtools, this field selection for Alt Channel Edge
(Accumulator Settings - Digital inputs) defines that the
accumulator will be reset to 0 when Digital CH2’s Input
State changes to High (see Set Up Digital and
Accumulator Inputs on page 43).
Glossary
66
Term
RSSI
Definition
Refresh
Receive Signal Strength Indicator. Clicking
forces BATtools to display a “live” RSSI reading. The
RM4100 Series units use a cellular network to
communicate. The units require an RSSI greater than –
110dB. RSSI is on a negative scale. Numbers closer to
zero indicate a stronger signal.
Serial
Unique serial number assigned to the unit at the factory
for identification purposes. Found on the BATtools Unit
Overview window.
SIM
The number assigned to the SIM card located inside the
RM4100 Series units. Found on the BATtools Hardware
Info window.
SMS
Short Message Service; text messaging service
component of phone, web, or mobile communication
systems. Found on the BATtools Hardware Info window.
TCP/IP Session
File transfer protocol. Found on the BATtools Hardware
Info window.
Type
The unit type connected to computer running BATtools.
Found on the BATtools Hardware Info window.
Unit Clock Time
Time-of-day clock running inside the unit. The clock is
used for all time-related operations such as transmission
schedules.
USB
Universal Serial Bus. Communication protocol used by a
computer for communications with an externally
connected device.
UTC Offset
Coordinated Universal Time. The primary time standard
by which the world regulates clocks and time. Time
zones around the world are expressed as positive or
negative offsets from the UTC, in eastward order from
the western-most zone (UTC-12:00). For example, Pacific
Time Zone is UTC -08:00, where the UTC Offset is -8
(see Set Up Reporting Schedule on page 33).
Glossary
67
Term
Definition
Verify Interruption
Only applies to units that support interruption. During
interruption verification, the BATtools verifies 3 or more
satellites are in view and the external relay switches from
off to on. If less than 3 satellites are in view, or the AC or
DC power source is not functional, or the external relay
does not switch from off to on, interruption verification
has failed.
Glossary
68
Index
Symbols
C
.NET Framework 9
installing 9
cathodic protection 15
caution symbol 3
channel reading
polarity 59
channel setup 36
circuit-breaker (switch) 23
current interrupter 20
A
AC channel settings 38
AC/DC power supply 23
Accumulator Count 44
ActiveSync 29
Alarm Persistence 40
alarms 36
analog inputs 37
graphs 42
Analog Inputs fields 37
antistatic wrist strap 3, 54
B
Battery
replacement 54
battery
backup 5
replacement 5
Battery Install Date 47
battery replacement 54
Battery Type field 47
BATtools 1, 20, 28
Accumulator Count 44
Analog Inputs 37
Battery Install Date 47
Digitals & Accumulators 43
Input Persistence 44
Instant Off 42
Output & Synchronization 36
Output Mode 36
starting 29
Sync Mode 36
unit information 31
branch circuit protection 5
Bullhorn information line 13
Bullhorn Web 1, 4, 28
D
DC channel settings 38
Deadband 64
Digitals and Accumulators fields 43
dual GPS/GSM antenna 21
E
earth ground 2
earth ground terminal symbol 3
ECCN code 63
Electrostatic Discharge 18
electrostatic discharge 20
equipment symbols 2
equipment warranty 17
ESD 20
precautions 3, 54
F
fuse 5
G
GPS antenna 20
GPS/GSM antenna 21
installation 21
ground 16, 24
connection 18
GSM antenna 20
H
hardware / software requirements 8
69
AC/DC 23
installation 22
safety specifications 22
hardware configuration 16
I
IMEI 65
incoming power
DC input 20
input device wiring 26
Input Persistence 44
input wires
installation 25
installation
overview 20
installation preparation 18
installation site qualifications 18
Instant Off 42
interrupter 20
L
LED
packet queue 16
lightning strikes 17
M
mercury relay 20
customer advisory 60
mounting magnets 21
O
Output Mode 36
overcurrent protection
20 amp fuse 5
branch circuit protection 5
circuit-breaker 5
overcurrent protection device 5
P
Packet Queue LED 16
Persistence 66
Polarity
channel readings 59
polling cycle 66
power disconnect 5
external overcurrent protection
device 5
overcurrent protection device 5
power supply
R
Radio ISN 66
Radio LED 16
rectifier current interruption 20
refresh unit information 29
relay
installation 24
mercury 20
normally closed 36
normally open 36
solid state 20
Replacement battery 54
replacement battery 5
Reporting Mode 34
reporting schedule 33
RM4100 Series
specifications 4
RM4150
inputs 15
RM4151
inputs 15
RSSI 67
GSM unit 67
S
safety symbols 2
satellite
SkyWave 15
schedule reporting 33
serial number
unit 67
site survey 18
solid state relay 20
specifications
RM4100 units 4
switch (circuit-breaker) 23
SWITCH OUT connector 25
symbols
caution 3
earth ground terminal 3
equipment 2
off supply 3
70
on supply 3
safety 2
Sync Mode 36
T
technical support 14
template
load 30
saving 48
transmission schedule 66
two-way communication 15
U
Unit Clock Time 67
USB 67
USB Config port 16
W
warning symbol 3
wiring
diagram 16
standards 23
71

RM4100 User Guide - American Innovations

Transcription

Similar documents

Atlantis Energy Systems Inc.

Sensaphone 2000 Brochure-New

Coffing EC3 Manual

Check Out Andtech`s 2009 Newsletter

Garrett SuperWand - Garrett Metal Detectors

NAUTICO UTICO 3 NAUTICO UTICO 3

Model 1800 Literature PDF

Pak-Lite Flashlight

318CTB - RCS: Remote Control Solutions

LIFEPAK 500 Maintenance Checklist