OM, Flymo, Glide Master 340, Glide Master 360, Glide

Glide Master 340
Glide Master 360
Glide Master 380
Original Instructions
TIO
A
M
R
N
NFO
I
T
TA N se
R
nce
O
I M P before u re refere
tu
Read in for fu
ta
& re
For all customer enquiries or for replacement parts, contact:-
01325 300303
www.flymo.com
[email protected]
1
Carton Contents
Easi Reel
cable winder
electric cable with
moulded plug
start/stop levers
switchbox
cutting height
spacers (1 fitted to
lawnmower & 2 inside product under
grassbox)
instruction
manual
spanner/scraper tool
(inside product under
grassbox)
IMPORTANT !
Please check the contents of the carton are correct BEFORE assembling your new Flymo product.
IF ANY PARTS ARE MISSING CONTACT:- Husqvarna UK Ltd. Customer Service Department direct
Telephone :
01325 300303
Fax :
01325 302530
Safety
If not used properly this lawnmower can be dangerous! This lawnmower can cause serious injury to the
operator and others, the warnings and safety instructions must be followed to ensure reasonable safety
and efficiency in using this lawnmower. The operator is responsible for following the warning and safety
instructions in this manual and on the lawnmower. Never use the mower unless the grassbox or guards
provided by the manufacturer are in the correct position.
Explanation of Symbols on your product
Warning
Read the user instructions carefully to make
sure you understand all the controls and what
they do.
Always keep the product on the ground when operating. Tilting or lifting the product may cause
stones to be thrown out.
Keep bystanders away. Do not mow whilst
people especially children or pets are in the
area.
General
1. This product is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning the use of the product by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with
the product. Local regulations may restrict the age
of the operator.
Beware of sharp blades - remove plug from
mains before maintenance or if cable is damaged.
Blades continue to rotate after the machine is
switched off.
Keep the cable supply away from the cutting
means
Unwind and remove fully before use.
2. Only use the lawnmower in the manner and for the
functions described in these instructions.
3. Never operate the lawnmower when you are tired, ill or
under the influence of alcohol, drugs or medicine.
4. The operator or user is responsible for accidents or
hazards occurring to other people or their property.
Electrical
1. The British Standards Institute recommend the use of a
Residual Current Device (R.C.D.) with a tripping current
of not more than 30mA. Even with a R.C.D. installed
2
100% safety cannot be guaranteed and safe working
practice must be followed at all times. Check your
R.C.D. every time you use it.
2. Before use, examine cable for damage, replace it if
there are signs of damage or ageing.
3. Do not use the lawnmower if the electric cables are
damaged or worn
4. Immediately disconnect from the mains electricity supply if the cable is cut, or the insulation is damaged. Do
not touch the electric cable until the electrical supply
has been disconnected. Do not repair a cut or damaged cable. Replace it with a new one.
5. Your extension cable must be uncoiled, coiled cables
can overheat and reduce the efficiency of your mower.
6. Keep cable away from lawnmower, always work
away from the power point mowing up and down,
never in circles.
7. Do not pull cable around sharp objects.
8. Always switch off at the mains before disconnecting
any plug, cable connector or extension cable.
9. Switch off, remove plug from mains and examine electric
supply cable for damage or ageing before winding cable
for storage. Do not repair a damaged cable, replace it with
a new one. Use only Flymo replacement cable.
10. Always wind cable carefully, avoiding kinking.
11. Never carry the product by the cable.
12. Never pull on the cable to disconnect any of the plugs.
13. Use only on AC mains supply voltage shown on the
product rating label.
14. Our products are double insulated to EN60335.
Under no circumstance should an earth be connected to any part of the product.
Preparation
1. While using your product, always wear substantial
footwear and long trousers.
2. Make sure the lawn is clear of sticks, stones, bones,
wire and debris; they could be thrown by the blade.
3. Before using the machine and after any impact, check
for signs of wear or damage and repair as necessary.
4. Replace worn or damaged blades together with their
fixings in sets to preserve balance.
Use
1. Use the lawnmower only in daylight or good artificial light.
2. Avoid operating your lawnmower in wet grass,
where feasible.
3. Take care in wet grass, you may lose your footing.
4. On slopes, be extra careful of your footing and wear
non-slip footwear.
5. Mow across the face of slopes, never up and down.
6. Exercise extreme caution when changing direction
on slopes. Walk never run.
7. Mowing on banks and slopes can be dangerous. Do
not mow on banks or steep slopes.
8. Do not walk backwards when mowing, you could trip.
9. Never cut grass by pulling the mower towards you.
10. Switch off before pushing the mower over surfaces
other than grass.
11. Never operate the lawnmower with damaged guards
or without guards in place.
12. Keep hands and feet away from the cutting means at
all times and especially when switching on the motor.
13. Do not tilt lawnmower when the motor is running, except when starting and stopping. In this case, do not
tilt more than absolutely necessary and lift only the part
which is away from the operator. Always ensure that
both hands are in the operating position before returning the appliance to the ground.
14. Never pick up or carry a mower when it is operating
or still connected to the mains supply.
15. Remove the plug from the mains :
before leaving the mower unattended for any period;
before clearing a blockage;
before checking, cleaning or working on the appliance;
if you hit an object. Do not use your lawnmower
until you are sure that the entire lawnmower is in a
safe operating condition;
if the lawnmower starts to vibrate abnormally. Check
immediately. Excessive vibration can cause injury.
Maintenance and storage
1. Caution: Do not touch rotating blade(s)
2. Keep all nuts, bolts and screws tight to be sure the
lawnmower is in safe working condition.
3. Check the grassbox frequently for wear or deterioration.
4. Replace worn or damaged parts for safety.
5. Only use the replacement blade, blade bolt, spacer
and impeller specified for this product.
6. Be careful during adjustment of the lawnmower to
prevent entrapment of the fingers between moving
blades and fixed parts of the machine.
7. Store in a cool dry place and out of reach of
children. Do not store outdoors.
Cables
CABLES - IMPORTANT
• Use only 1.00mm2 size cable up to 40 metres length
maximum.
Maximum rating :
1.00mm2 size cable, 10 amps 250 volts AC.
• YOUR PRODUCT IS SUPPLIED WITH AN ELEC-
TRIC MAINS CABLE FITTED WITH A FEMALE
CONNECTOR.
1. Flymo Mains Cables and Extension Cables are available
from your local Approved Service Centre.
2. Do not wire an extension cable directly to your product yourself. Please contact your local Approved
Service Centre for further information on the connectors and kits available.
3. Only use extension cables specifically designed for
outdoor use.
CONNECTORS - IMPORTANT
• Flymo connectors are suitable for use with 2 core
cable only. Under no circumstances should these
connectors be used for earthed products.
• All Flymo connectors and cables are of splashproof
construction. They are not waterproof and must not
be left outside permanently nor should they be submerged or immersed in water. Do not let cable lay or
trail through pools of water or splashed with water
from hose pipes.
MAINS PLUG REPLACEMENT - IMPORTANT
• If the plug supplied is cut off it should be de-
1.
2.
3.
4.
5.
6.
7.
stroyed. There is an electric shock hazard if a cut
off plug is inserted into a 13 amp socket.
No earth required. Flymo products are double insulated to EN60335 and under no circumstances
should an earth be connected to any part of the product.
Ensure the mains voltage suits your product
IMPORTANT!
The wires in the mains lead are coloured in accordance with the following code:
BLUE
NEUTRAL
BROWN LIVE
The wire which is coloured BLUE must be connected
to the Terminal which is marked with the letter 'N' or
coloured BLACK.
The wire which is coloured BROWN must be connected to the Terminal which is marked with the letter
'L' or coloured RED.
It is important that the outer sheath is clamped correctly into the 3-pin plug.
If in doubt consult your local Service Repairer or
qualified electrician before the machine is used.
A 13 Amp fuse must be fitted to the Mains Plug.
The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard
against electrocution.
3
Assembly Instructions
A
B
Preparing your lawnmower for use
• Your lawnmower is supplied with the upper handle folded over the machine for packing and
transportation.
Handle in Operating Position
1. Lift handle as illustrated in figure A.
• Do not drop the handle.
• Make sure that the cable does not become
trapped between the handles
Attach the Easi-Reel cable winder as illustrated in
figure B
This is used to store the power cable after using the
product - see ʻEasi-Reel Cable Winderʼ section.
Starting and Stopping
C
D
E
F
G
H
To Start your Lawnmower
1. Connect the female extension cable connector to the
back of the switchbox. (C)
2. Form a loop in mains cable and push the loop through
the slot as illustrated in picture (D)
3. To secure, position the loop over the hook and pull the
cable back through the slot as illustrated in picture
(E).
4. Connect plug to mains and switch on.
5. To prevent a ring being cut in your lawn and to clear
any residual grass in the collection chute, tilt your
lawnmower slightly (F).
The switchbox is provided with a lock-off button (G1)
to prevent accidental starting.
6. Press and hold the lock-off button (G) on the switchbox, then squeeze one of the Start/Stop levers towards the upper handle (H).
7. Continue to squeeze the start/stop lever towards the
upper handle and release the lock-off button.(J)
8. When the lawnmower has reached full speed gently
lower it onto the lawn.
NOTE: There are two start/stop levers fitted. Either
one can be used for starting the lawnmower.
IMPORTANT: Do not use the start/stop levers intermittently
1
J
To Stop your Lawnmower
1. To prevent a ring being cut in your lawn and to clear
any residual grass in the collection chute, tilt your
lawnmower slightly (F).
2. Release the pressure on the Start/Stop lever.
How to Mow
1. Start mowing the edge of the lawn nearest to the
power point so the cable is laid out on the lawn you
have already cut.
2. Mow twice a week during the growing season, your lawn
will suffer if more than a third of its length is cut at one
time and this may also result in poor collection.
Do Not Overload Your Mower
Mowing long thick grass may cause the motor speed to
drop, you will hear a change in the motor sound. If the
motor speed drops you may overload your lawnmower
which may cause damage. When mowing in long thick
grass a first cut with the cutting height set higher will help
reduce the load. See Adjusting the Cutting Height.
REMEMBER: For best grass collection always mow in a
straight line, do not swing the lawnmower from side to side.
Grassbox Instructions
K
grassbox
is full
grassbox
is empty
L
Grassbox Full (K)
1. As the grassbox fills up, grass will be clearly visible
through the window in the lid (K).
2. When the window is full it is time to empty the grassbox.
Emptying the Grass
• Stop the lawnmower, and wait until the blade has
stopped rotating BEFORE lifting the grassbox lid.
1. Lift grassbox lid. (L)
2. Lift out grassbox and empty. (M)
3. Replace grassbox and close lid carefully.
• Failure to fit the grassbox and grassbox lid correctly will
cause poor grass collection. Ensure there is no grass
trapped between the lid and the hood.
M
Lift out box
Easi-Reel Cable Winder
N1
N3
N2
N4
Storing your cable in the Easi-Reel cable winder
1. Insert the female connector into the centre of the cable
winder (N1)
2. Place the cable under the cable guide (N2)
3. Turn the cable winder (N3) until all of the cable is
wound in.(N4)
Unwinding the cable before re-use
1. Pull the cable by the plug and unwind the cable fully.
• Ensure that the cable is released from the cable
guide (N2) before using your machine.
• Ensure cable is not entangled with any other cables and that it is not trapped in any parts of the
product.
Spanner & Spacers
P
There is a spanner and additional spacers, for height
adjustment, stored inside the lawnmower underneath
the grassbox.(P) These can be stored inside the
lawnmower even whilst it is use.
Adjusting the Cutting Height
Q
Always handle the blade with care - sharp edges
could cause injury. USE GLOVES. Never use more
than 3 Cutting Height Spacers. Spacers must only be
fitted between the blade and the fan and NEVER between the blade and the bolt.
1. Remove the blade bolt, and blade as described in Removing the Blade and Fan.
2. For a Lower Cut - Add spacers to a maximum of 3.
3. For a Higher Cut - Take spacers away.
4. Refit the blade as described in Fitting the Blade and Fan.
Removing and fitting the Blade and Fan
Removing the Blade and Fan
1. To remove the blade bolt, hold the fan firmly and with
the spanner provided loosen the blade bolt by turning
it anti-clockwise (Q).
2. Remove the blade bolt, blade, spacers and fan. (R)
3. Inspect for damage and clean as necessary.
• Renew your metal blade after 50 hours mowing or
2 years whichever is the sooner - regardless of
condition. If the blade is cracked or damaged replace it with a new one. Never use a blade bolt if
the insulated head is damaged cracked or missing.
Fitting the Blade and Fan
1. Ensure the fan is located correctly.(R)
2. Place the spacers onto the fan ensuring the pegs have
located into the holes.(R)
3. Place the blade onto the spacers ensuring the pegs have
located into the holes on the blade and ensuring the
blades is positioned as illustrated in Figure R
4. Place the blade bolt through the centre hole of the blade.
5. Tighten down clockwise by hand.
6. Hold the fan firmly and tighten the blade bolt with the
spanner provided.
R
blade bolt
blade
spacers
fan
Caring for your Lawnmower
Cleaning
IMPORTANT: It is very important that you keep your
lawnmower clean. Grass clippings left in any of the air
intakes or under the hood could become a potential fire
hazard. USE GLOVES.
Switch off and remove the plug from the mains before cleaning.
It is recommended that you clean your lawnmower
straight after mowing while the grass is still wet.
1. Remove grass from under the hood with the spanner/scraper tool provided. (S1)
2. Remove the blade, see Figure R, to gain access to
the fan and clean with a soft brush. (S2)
3. Lever the roller out of position and clean with a soft
brush. (S3)
4. Using a soft brush, remove grass clippings from:
• all air intakes (S4)
• grassbox (S5)
• inside of grassbox lid (S6 & S7)
5. Wipe over the surface of your lawnmower with a dry
cloth.(S8)
• IMPORTANT
Never use water for cleaning your lawnmower. Do not
clean with chemicals, including petrol, or solvents some can destroy critical plastic parts.
S1
S2
S3
S4
S5
S6
S7
S8
Cleaning the Easi-Reel cable winder
1. At the back of the cable winder, squeeze together the
two catches (T1) and remove the cable spool.
2. Clean the cable spool and the area it was located with
a soft brush (T2 & T3)
3. Replace the cable spool, ensuring it clicks into place.
Transporting the lawnmower.
• The lawnmower may be transported on its roller (V).
At the End of the Mowing Season
1. Replace blade, bolts, nuts or screws, if necessary.
2. Clean your lawnmower thoroughly.
3. Ask your local Service Centre to clean the air filter thoroughly
and carry out any service or repairs required.
4. Make sure that the electric cable is coiled properly.
Storing the lawnmower
The handles can be folded to take up the minimum of
space
T2
T1
T3
V
1. Hold onto the lower handle with your left hand as illustrated in fig. W.
2. Hold the upper handle with your right hand and push
in the direction of the arrow.
3. Move the handle slowly forward to rest it on the lawnmower (X). Do not drop the handle.
•
•
•
Ensure the switchbox cable is not trapped.
Do not hang the product on the wall as this will damage the switchbox.
Store in a dry place where your lawnmower is protected from damage.
W
X
Fault Finding Hints
Fails to Operate
1. Is the correct Starting procedure being followed?
See ʻTo Start your Lawnmowerʼ
2. Is the Power Turned On?
3. Check the fuse in the plug, if blown replace.
4. Fuse continues to blow?
Immediately disconnect from the mains electricity
supply and consult your local approved Service
Centre.
Poor Flotation
1. Disconnect from the mains electricity supply.
2. Clean the underside of the hood and the fan blades.
3. Raise to a higher height of cut. See ʻAdjusting the
Cutting Heightʼ.
4. If poor flotation persists?
Disconnect from the mains electricity supply and
consult your local approved Service Centre.
Poor Collection
1. Is the grassbox lid firmly closed?
2. Is the grassbox fitted correctly?
3. Are you mowing correctly?
4. Check all air vents and openings are not obstructed.
5. Raise to a higher height of cut. See ʻAdjusting the
Cutting Heightʼ.
6. If poor collection persists.
Disconnect from the mains electricity supply and
consult your local approved Service Centre.
Excessive Vibration
1. Disconnect from the mains electricity supply.
2. Check that the blade is fitted correctly?
3. If the blade is damaged or worn, replace it with a new one.
4. If vibration persists?
Disconnect from the mains electricity supply and
consult your local approved Service Centre.
Guarantee & Guarantee Policy
If any part is found to be defective due to faulty manufacture
within the guarantee period, Husqvarna UK Ltd., through its Authorised Service Repairers will effect the repair or replacement
to the customer free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty
adjustment by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired,
taken apart or tampered with by any person not authorised by Husqvarna UK Ltd.
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
*
This guarantee is additional to, and in no way diminishes
the customers statutory rights.Failures due to the following
are not covered, therefore it is important that you read the
instructions contained in this Operator's Manual and understand how to operate and maintain your machine:
Failures not covered by guarantee
*
Replacing worn or damaged blades.
*
Failures as a result of not reporting an initial fault.
*
Failures as a result of sudden impact.
*
Failures as a result of not using the product in accordance
with the instructions and recommendations contained in
this Operator's Manual.
*
Machines used for hire are not covered by this guarantee.
*
The following items listed are considered as wearing
parts and their life is dependent on regular maintenance
and are, therefore not normally subject to a valid warranty claim: Blade, Electric Mains cable, belt.
*
Caution!
Husqvarna UK Ltd. does not accept liability under
the warranty for defects caused in whole or part, directly or indirectly by the fitting of replacement parts
or additional parts that are not either manufactured
or approved by Husqvarna UK Ltd., or by the machine having been modified in any way.
Service Recommendations
1. We strongly recommend that your product is serviced at least every twelve months, more often in a
professional application.
2. Always use genuine Flymo Spare Parts.
3. Prepacked spares are available from most Husqvarna UK Ltd. stockists.
4. Your product is uniquely identified by a silver and
black product rating label
5. If you have a problem with your machine contact your local
Approved Service Centre ensuring you have full details of
your product as described on the product rating label.
6. Should it be necessary for work to be carried out
by your Service Centre, it is important to take
your complete machine including cable and any
extension cables used.
A network of specialist dealers can be found in your
local Yellow Pages.
To obtain service on your Flymo product simply telephone or visit your local Service Centre.
Should you require service under the terms of our guarantee the Service Centre will require proof of purchase.
All of the centres listed stock genuine Flymo Spare
Parts.
NOTE: Our Service Repairers act on their own behalf and are not empowered to commit or legally
bind Husqvarna UK Ltd. in any manner whatsoever.
Environmental Information
Husqvarna UK Ltd. are manufactured under an Environmental Management System (ISO 14001) using, where practical, components manufactured in the most environmentally responsible manner, according to company procedures,
and with the potential for recycling at the end of the productsʼ life.
•
Packaging is recyclable and plastic components have been labelled (where practical) for categorised recycling.
•
Awareness of the environment must be considered when disposing of ʻend-of-lifeʼ product.
•
If necessary, contact your local authority for disposal information.
The symbol
on the product or on its packaging indicates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic
equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
For more detailed information about recycling of this product, please contact your local council office, your household
waste disposal service or the shop where you purchased the product.
EC Declaration of Conformity
Husqvarna UK Ltd., Aycliffe Industrial Park
Newton Aycliffe, Co. Durham, DL5 6UP, England
Declare under our sole responsibility that the product(s);
Category............................Electric Lawnmower
Type(s) ...........................GM340, GM360, GM380
Identification of Series.......See Product Rating Label
Year of Construction..........See Product Rating Label
Conforms to the essential requirements & provisions of the following EC Directives:
98/37/EC (until 31.12.09), 2006/42/EC (from 01.01.10), 2004/108/EC, 2000/14/EC
based on the following EU harmonized standards applied:
EN60335-1, EN60335-2-77, EN836, EN50366, EN55014-1, EN61000-3-2, EN61000-3-3
The maximum A weighted sound pressure level LpA at the operatorʼs position, recorded on a sample of the above product(s)
corresponds to the Level given in the table.
The maximum hand / arm vibration weighted value measured according to EN ISO 5349 on a sample of the above product(s)
corresponds to the Value given in the table.
2000/14/EC: The Measured Sound Power LWA & Guaranteed Sound Power LWA values are according to the tabulated figures.
Conformity Assessment Procedure..................
Annex VI
Notified Body....................................................
Intertek, Cleeve Road
Leatherhead, Surrey
KT22 7SB, England
Newton Aycliffe 25/11/2008
M.Bowden
Research & Development Director
Husqvarna UK Ltd.
Type
Width of Cut (cm)
Speed of Rotation of Cutting Device (rpm)
Power (kW)
Measured Sound Power LWA (dB(A))
Guaranteed Sound Power LWA (dB(A))
Level (dB(A))
Value (m/s2)
Weight (Kg)
GM340
34
4200
1550
90
92
79
1.86
11.45
GM360
36
4200
1650
90
92
79
1.86
11.45
GM380
38
4200
1750
90
92
79
2.75
11.55
Husqvarna UK Ltd.
Aycliffe Industrial Park
NEWTON AYCLIFFE
Co.Durham DL5 6UP
ENGLAND
Telephone - (00) 44 1325 302302 Fax - (00) 44 1325 310339
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
5052848-01