INARI Inari Bring Up Guide

Transcription

Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Title: Inari bring up guide
Revision: B
Prepared by: Timo Kinnunen
Issue Date: 22.5.2014
INARI
Inari Bring Up Guide
__________________________________________________________________________
Page 1 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
INTRODUCTION ................................................................................................................ 3
1.
CREATE INSTALLATION USB STICK ............................................................................. 4
2.
HOW TO CONNECT EXTERNAL USB-DEVICES TO INARI ............................................... 5
3.
HOW TO UPDATE OS AND BIOS ................................................................................. 6
3.1. 32BIT BIOS IS INSTALLED BUT DEVICE DOES NOT BOOT TO WINDOWS ....................................... 6
3.2. 32BIT WINDOWS IS ALREADY INSTALLED AND BOOTS NORMALLY .............................................. 8
4.
HOW TO UPDATE ONLY BIOS..................................................................................... 9
5.
HOW TO FIND OUT THE PRODUCT VARIANT AND THE HW VERSION ........................ 10
6.
HOW TO UPDATE ULPMC FW .................................................................................. 14
6.1. FROM EFI SHELL ........................................................................................................... 14
6.2. FROM WINDOWS .......................................................................................................... 16
7.
HOW TO UPDATE TOUCH CONFIGURATION ............................................................. 17
8.
HOW TO CHECK TOUCH FW VERSION ...................................................................... 18
9.
HOW TO UPDATE SENSOR HUB CONFIGURATION .................................................... 19
10.
HOW TO UPDATE HUAWEI MODEM (MU736) FIRMWARE ON INARI DEVICE ......... 20
__________________________________________________________________________
Page 2 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
Introduction
This document describes how to install Windows 8.1 and essential firmware updates to
Inari product family.
__________________________________________________________________________
Page 3 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
1. Create installation USB stick
Follow these steps to create bootable installation USB stick.
Note: Use 8GB stick or larger.
1. Insert USB stick to host PC.
2. From Windows Explorer right click USB stick and Format to FAT32, as below:
3. Extract desired autoInstaller zip to the USB stick.
4. Rename stick as “BOOTME” by right click in Explorer and rename.
__________________________________________________________________________
Page 4 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
2. How to connect external USB-devices to Inari
1. Inari tablet
2. USB keyboard connected to USB hub
3. USB hub with external power source
4. Bootable installation USB stick connected to USB hub
5. Power source (for setup without battery pack)
6. USB charger connected to micro USB port
7. USB cable connecting hub to USB port
__________________________________________________________________________
Page 5 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
3. How to update OS and Bios
NOTE: For installing 32bit Windows, device MUST have:
- 32 bit Windows and BIOS installed
OR
-
32bit BIOS installed
3.1. 32bit BIOS is installed but device does not boot to Windows
1. Attach installation USB stick to USB hub as in example.
2. Reboot the device.
3. When Bios logo is seen, press ESC button from keyboard.
4. Device boots to BIOS.
5. Select “Boot Manager” with keyboard and press Enter.
6. When USB stick is attached three items are seen:
__________________________________________________________________________
Page 6 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B

Windows Boot Manager (eMMC)

EFI USB Device (USB stick)

Internal EFI Shell
7. Select “EFI USB Device” and press Enter.
8. Device boots to WinPE and installs OS and BIOS. Installation will take 9 min.
9. If you at this point get an error on the display saying ‘Windows Boot Manager failed’,
just press OK to continue installation
10. When complete, device boots to Windows 8.1.
11. If touchscreen or sensors have orientation issues, update configurations according to
chapters: ‘How to Update Touch Configuration’ and ‘How to Update Sensor Hub
Configuration’.
__________________________________________________________________________
Page 7 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
3.2. 32bit Windows is already installed and boots normally
1. Boot device do Windows
3. Run ‘bootToUSB.exe’ as Administrator from the root of installation USB stick
4. Click ‘Boot To USB’ button from the appearing dialog.
5. Wait until device has made necessary updates to configurations.
6. Device boots to WinPE and installs OS and BIOS. Installation will take 9 min.
7. If you at this point get an error on the display saying ‘Windows Boot Manager failed’,
just press OK to continue installation
8. When complete, device boots to Windows 8.1.
__________________________________________________________________________
Page 8 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
4. How to update only BIOS
NOTE: When OS is updated according to chapter How to update OS and Bios, BIOS is
updated automatically and there is no need for separate BIOS update.
1. Boot device do Windows
3. Run ‘Aava_bios_inari_<version>-32].exe’ from the ‘biosUpdate’ folder of installation
USB stick.
4. Click ‘OK’ button from the appearing dialog.
5. Device will restart and install BIOS update.
__________________________________________________________________________
Page 9 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
5. How to find out the product variant and the HW version
1. Open Settings
2. Select Change PC Settings
__________________________________________________________________________
Page 10 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
3. Select Update and Recovery
4. Select Recovery
__________________________________________________________________________
Page 11 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
5. Select Restart now
6. Select Troubleshoot
7. Select Advanced options
8. Select UEFI Firmware Settings
9. Press Restart
10. The device will boot to Bios and Bios menu will appear
11. Use USB keyboard to select SCU.
__________________________________________________________________________
Page 12 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
12. Check Board ID for Product Variant information and Fab ID for HW version.
__________________________________________________________________________
Page 13 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
6. How to update ULPMC FW
ULPMC update is needed for Inari hardware.
6.1. From EFI Shell
2. Reboot the device.
3. When Bios logo is seen, press ESC button from keyboard.
4. Device should boot to BIOS.
5. Select “Boot Manager” with keyboard and press Enter.
6. When USB stick is attached three items are seen:

Windows Boot Manager (eMMC)

EFI USB Device (USB stick)

Internal EFI Shell
__________________________________________________________________________
Page 14 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
7. Select Internal EFI Shell and press Enter.
8. Go to ULPMC FW Update folder

Type “fs1:”

Type “cd ulpmc_fw_update”
9. Start ULPMC FW updater:

Type “Ulpmc_fw_update.nsh”
10. Accept EULA, browse to bottom with enter and on the last page type “y”
11. Check that ULPMC FW update is Completed Successfully.
12. Device is now ready.

Type “exit” to return to BIOS menu.

Select “Continue” from BIOS menu to boot the device.
__________________________________________________________________________
Page 15 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
6.2. From Windows
NOTE: Aava_bios_inari_028 or newer is needed for the update from Windows.
1. Run UPDATE_ULPMC.bat from ‘ulpmc_fw_update\driver’ folder of installation USB
stick.
2. Click ‘Install’ on Windows Security prompt to install driver.
3. The device will be rebooted automatically after driver is installed.
4. ULPMC FW will be updated on boot phase.
5. After install you can check if install was successful from device manager:
o ‘Firmware->Device Firmware’: yellow bang indicates problem.
o ‘Firmware->Device Firmware ->Propertiers->Details->Hardware Ids’: last
parameter beginning with REV tells you current version number(for
example REV_2817 for Aava_ULPMC_28_Aava_17)
6. If installation fails for some reason, uninstall driver with "Delete the driver..."
selected. This is necessary before retrying.
__________________________________________________________________________
Page 16 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
7. How to update touch configuration
IMPORTANT: Before programming touch configuration make sure you know
the product variant of the particular device. If not sure, see chapter How to
find out the product variant and the HW version for instructions.
1. Start Windows and connect installation USB stick to device
2. Run [usb stick]:\atmelTouch\”Product Variant”\flashTouchCfg.bat
Product Variant: Inari8 or Inari10, etc.
3. Check that “Configuration was updated successfully” is shown.

Note: you have 20 seconds to check the message before the window closes.

If updating fails, you can retry running the flashTouchCfg.bat.
__________________________________________________________________________
Page 17 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
8. How to check touch FW version
Touch FW check/update is not mandatory step of SW update. In case you are not
sure of touch FW, you can check the version with following instructions. If version
is different than 2.0, please contact to [email protected] for further
info.
1. Boot windows to “Efi settings”

When Windows is running, swipe in from the right edge of the screen and tap
“Settings”.

Select ”Change PC settings”->”Update and recovery”->”recovery”->”advanced
startup”->“Restart now”.

In Option boot menu select “Troubleshoot”->”Advanced options”->”Uefi firmware
Settings”->”Restart”

In BIOS menu set “SCU”->”Advanced”->”LPSS & SCC Configuration”->Touchpanel
FW device” to Enable

Exit and save F10
2. Start windows and connect installation USB stick to device
3. Install FW flash driver [USB stick]:atmelTouch/mxtBootBridge/x86/mxtBootBridge.inf
4. Run getTouchFW.bat in atmelTouch folder and check version info from output.
__________________________________________________________________________
Page 18 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
9. How to update Sensor Hub configuration
It should not be necessary to configure Sensor Hub. However if there is something
strange in behaviour of the Sensor Hub and the sensors, then perform the following to
update correct configuration values to hub
1. Start Windows and connect installation USB stick to device
2. Run update script as administrator:
[usb stick]:\sensorsUpdate\UpdateSensors.bat
3. Check that “Sensor orientation update OK” is shown.
If updating fails, you can retry running the UpdateSensors.bat.
__________________________________________________________________________
Page 19 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
10. How to update Huawei modem (MU736) firmware on Inari device
1. Start Inari tablet
2. Open Device Manager and check that modem is up and running, no yellow bang:
Network adapters -> HUAWEI Mobile Broadband Module
3. Attach installation USB stick to Inari.
4. Execute modem flasher, double click:
“modem_fw_update/MU736Update_12.100.00.01.1818.exe”
5. Following steps are shown during the update process, follow the instructions:
__________________________________________________________________________
Page 20 of 21
Document No:
© Aava Mobile Ltd.
CONFIDENTIAL
Revision: B
__________________________________________________________________________
Page 21 of 21

INARI Inari Bring Up Guide

Transcription

Similar documents

EMUKEY Product Sheet

What does it measure? The Visioscan® VC 98 USB is a special UVA

Convert your laptop to a desktop in seConds!

INARI-CE_Right Issue Announcement 13012015

portable usb dj mixer + scratch controll er + dj software

3.5" SATA to USB 3.0 External Hard Drive Enclosure

SC-2300 spec

Charging your PowerSLIMTM 9.0 - eshop x

www.globo.com.pl OPTICUM HD 9600 PRIMA id: O9600PRIMA

AccuPower hardware

Technical specification