Assembly manual - Modele.sklep.pl
Transcription
Assembly manual - Modele.sklep.pl
U.S.S. ENTERPRISE NCC-1701-D TM AMT662 DECAL & PAINT INSTRUCTIONS HINT: For more details on paint and decal placement, refer to box art. 24 26 J 23 21 22 25 28 27 70 x4 B 50 x2 67 66 54 x2 B G E B 42 44 B 62 60 64 ® 38 32 40 36 71 65 U.S.S. ENTERPRISE NCC-1701-D TM 33 30 34 69 55 61 63 51 53 62 60 43 52 69 J 63 61 64 65 HINT: To seal decals, and for a more finished look, apply a clear dullcoat spray after paint and decals are completely dry. KEY TO NUMBERING B 29 37 35 41 31 39 KEY TO PAINT COLOR First Layer Decal Application A Light Gray F Copper 000 Second Layer Decal Application B Medium Gray G Yellow 000 Opposite Side Decal Application C Black H Pearl White Paint Color (optional) D White I E Red J Medium Blue 000 A Light Blue Special thanks to E. James Small for developing the aztec decals included in this kit. For excellence in model building, visit his web site at smallartworks.ca AMT is a registered trademark of Learning Curve Brands, Inc. used under license to Round 2, LLC. © 2010 Learning Curve Brands, Inc. All rights reserved. TM, & © 2010 CBS Studios Inc. All rights reserved. STAR TREK and related marks are trademarks of CBS Studios Inc. © 2010 Paramount Pictures Corp. All rights reserved. © 2010 Round 2, LLC South Bend, IN 46628 USA. Product and packaging designed in the USA. Made in China. All rights reserved. ® A662-200 GENERAL ASSEMBLY: This highly-detailed kit features precision-tooled parts for ease of assembly. Care and patience must be exercised to achieve optimal results. The kit has been designed to assemble via snap assembly. GLUE ASSEMBLY: If a modeler chooses to glue their model, it is B B ASSEMBLY INSTRUCTIONS recommended that the instructions be examined carefully before applying cement. You will find this very helpful, as it will allow you to gain a clear understanding of how the parts fit together in order to best plan painting and final assembly. If doing a test fit, scraping the attachment pins with a knife blade may be beneficial to separate parts before re-assembling with glue. SUB-ASSEMBLIES: Note that this kit is intended to be built in sub-assemblies. This makes building the kit far more manageable. It is very important to note that it can be extremely advantageous to apply paint and decals to sub-assemblies before completing final assembly. DECALS & PAINT: This kit includes extensive water slide decals. Note that the large areas of aztec paneling decals are applied first, allowed to dry, and a second set of smaller decals (primarily marking decals) are placed on top. These decals are compatable with setting solution which can be applied to conform around surface details. Paint is not required to produce satisfactory results. However, some modelers prefer to add additional painted detail to their kits. See the diagrams on this sheet for instructions regarding decal placement and optional paint specs. For best results apply dull coat for final finish. For more model building tips and techniques, visit the Workbench section of our website at round2models.com/workbench round2models.com U.S.S. ENTERPRISE NCC-1701-D 1 4 FINAL ASSEMBLY 4A Snap the starboard HINT: It is helpful to apply paint and decals to subassemblies before completing final assembly. nacelle in place on starboard strut. Press tightly until nacelle clicks into place. Repeat assembly with port nacelle and port strut. SAUCER Snap the upper saucer half (30) and lower saucer half (31) together, being sure to press together tightly for a snug fit. 30 4B 31 2 Port (left) NACELLES Snap the port nacelle halves (35 & 36) together. Repeat assembly with starboard nacelle halves (37 & 38). U.S.S. ENTERPRISE NCC-1701-D TM 35 & 37 DECAL & PAINT INSTRUCTIONS HINT: If painting ship an overall base color, allow paint to dry thoroughly before applying decals. Kit is molded in correct base color; however, if you desire to paint your model, Enterprise-D is a base color of Light Gray A 36 & 38 3 Starboard (right) Snap saucer assembly in place on secondary hull. Seat the rear tab and slot first, then press saucer down until it snaps securely into place. IMPORTANT: For keys to decal numbering and paint color, see back page. SECONDARY HULL 59 Snap the secondary hull halves (32 & 33) together, trapping deflector dish (34) in place. 68 58 B 5 72 9 13 11 7 3 19 1 69 56 32 45 49 46 18 14 17 15 47 B 34 48 57 B 16 69 2 59 33 68 58 B 4 20 6 10 8 12
Similar documents
POL820 Instr Sht Front1
#106 into the left side of the hull and part #107 into the right side of the hull.
More information