2N Helios IP Server Setup Guide

2N Helios IP and Elastix Server
Setup Guide
http://www.elastix.org
PaloSanto Solutions
2N Helios IP Server Setup Guide
1.0 Setup Diagram
Figure 1-1 is a setup diagram for a single intercom 2N Helios IP configuration. The
intercom is setup as a SIP telephony device.
Figure 1-1. Setup Diagram
2.0 Host PC Environment
Table 2-1. Host Server Environment Details
Hardware Type
Hardware Version
Software Type
Software Version
Description
Elastix Appliance ELX-Series
ELX-3000
Elastix
2.3
3.0 Test Setup Equipment
Equipment
IP (SIP) Phone
2N
PoE Switch
Table 3-1. Test Setup Equipment
Model
Version
N/A
N/A
Helios IP 9137130KE
FW: 1.11.0.268.0 (HW: 535v2)
N/A
N/A
2
PaloSanto Solutions
2N Helios IP Server Setup Guide
4.0 Setup Procedure
To set up the Elastix Server for the 2N Helios IP,
1. Go to the web address of the Elastix Server Login page. The web address is
determined by the user, for this guide we have used the IP address 192.168.5.186
2. On the Login page, type the username and password for an administrative user into
the Username and Password fields, see Figure 4-1. The username and password are
determined by the user.
Figure 4-1. Login
3. Press Enter or click on the Submit button to go to Elastix’s Dashboard
4. Once inside, click on the PBX tab on the menu at the top of the screen
Figure 4-2. Dashboard
3
PaloSanto Solutions
2N Helios IP Server Setup Guide
5. Click on the Submit button to add an extension, see Figure 4-3. This will take you to
the Add SIP Extension page.
Figure 4-3. Add an Extension
6. On the Add SIP Extension page (Figure 4-4), fill in the following information:
• User Extension (301 in this example)
• Display Name (2NHeliosIP in this example)
• secret (h7Dka3Rf9si0t in this example)
Figure 4-4. Add SIP Extension
4
PaloSanto Solutions
2N Helios IP Server Setup Guide
7. Click on the ‘Submit’ button at the end of the page. The extension will be created and
you will see the page on Figure 4-5 displaying the “Apply Configuration Changes Here”
pink ribbon on top of the screen.
8. Click in the “Apply Configuration Changes Here” link
Figure 4-5. Apply Configuration Changes Here
9. With this you have just finished creating a SIP extension that will be used by the 2N
Helios IP to register with the Elastix Server. Repeat Steps 5 through 8 to similarly
create another extension (different values on Step 6) to be used by the IP (SIP) Phone to
register as well, we’ll use extension 302for it in this example. Once finished you will
see something similar to Figure 4-6
Figure 4-6. 2N Helios IP and IP Phone extensions successfully created
10. To register the 2N Helios IP, you will need to enter the information from the
extension created on the Elastix Server (Step 6) into the Helios IP by logging into the
2N Helios IP WebUI.
Log in to the 2N Helios IP WebUI by pointing your browser to the 2N Helios’s IP
address.
For the initial configuration, refer to the 2N Helios IP User Manual which can be found
at: http://www.2n.cz/download/2/3/8/4/2n-helios-ip-user-manual-pb1510-v1.11.1.18.pdf
You can figure out the IP address by running any network scanner or packet capture
software.
Factory default settings
Web Access User Name Admin
Web Access Password
2n
5
PaloSanto Solutions
2N Helios IP Server Setup Guide
11. When prompted, enter the Web Access Username and Web Access Password to
access the WebUI (Figure 4-7).
Figure 4-7. 2N Helios IP WebUI
12. Use the information from the Add SIP Extension page (Step 6) to enter the
following necessary information on “Advance Setting => SIP Settings“ section of the
2N Helios IP WebUI (Figure 4.8):
User Settings
 Display Name(2NHeliosIP in this example)
 User ID(301 in this example)
 Domain(Elastix Server’s IP Address, 192.168.5.186 in this example)
 Use Auth ID: Yes
 Auth ID(301 in this example)
 Password (h7Dka3Rf9si0t in this example)
SIP Proxy Settings
 Proxy Address(192.168.5.186 in this example)
 Port: 5060
SIP Registration
 Register Helios IP: Yes
6
PaloSanto Solutions
2N Helios IP Server Setup Guide
Figure 4-8. Account Configuration
13. Once you have entered the required information, click on ‘Submit’ button located at
the end of the page on the right. To apply changes reboot the intercom by going to
“Tools => Reboot device”. If the intercom is not able to register after rebooting, make
sure you’ve entered the correct information. Confirm the registration in “Information”
section (Figure 4-9).
Figure 4-9. Information section
14. Once it is registered, we have to assign a number extension to the first quick dialing
button on the 2N Helios IP. To do this go to “Basic Settings => Phone Book” and fill in
the following information:
7
PaloSanto Solutions
2N Helios IP Server Setup Guide
General Settings


Position Enable: Yes
Position Name (2NHeliosIP in this example)
Phone Numbers



Number 1(302 in this example)
Number 2(Any other extension if you require)
Number 3 (Any other extension if you require)
Figure 4-10. Phone Book
15. Once you have entered the extension apply changes.
16. To test the 2N Helios IP call reception feature, pick up the previously configured IP
(SIP) Phone and call the2N Helios IP’s extension number (301 in this example). When
the call is established, speak into the phone and verify that your voice can be heard
through the intercom and vice versa.
17. To test the 2N Helios IP call origination feature, press the first quick dialing button
previously configured and the IP (SIP) Phone will start ringing. When the call is
established, speak into the intercom and verify that your voice can be heard through the
phone and vice versa.
This step completes the procedure.
8