864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs

 864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs
Installation Instructions (SKU 96900144)
Compatibility
864 HO NB
Packing List



Ember-Fyre Burner Assembly
Log Set With Embers and Rock Wool
Grate Assembly




Front & Rear Andiron Brackets
Burner Air Deflectors (Natural Gas and LP)
Rivet (for LP installations only)
Air Deflectors
Installation Tips
If using LP, convert the appliance before installing the burner.
Make sure to have the firebacks for the appliance on hand. They will be
installed before burner installation.
Installation Warnings
The logs are fragile, especially after being exposed to heat.
Make sure the gas control valve is OFF and the heater is cool before
servicing.
Failure to position the parts in accordance with these diagrams or failure to
use only parts specifically approved with this appliance may result in
property damage or personal injury.
The burner must be correctly positioned before installing the logs. Make sure
the burner is fully seated and the pilot is properly aligned.
Page 1 of 10
17601715.docx — 8/8/12
© Travis Industries, Inc.
864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs
Installation Instructions (SKU 96900144)
1.
Install the front and side air deflectors. On older models, these are pre‐installed at the factory. Note that the screw holes are circled below. The illustration below shows the air deflectors installed. Page 2 of 10
17601715.docx — 8/8/12
© Travis Industries, Inc.
864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs
Installation Instructions (SKU 96900144)
2.
Install the firebacks. 3.
Install the burner as shown below. NOTE: When installing the air deflectors, make sure the locking tabs face toward the front of the burner. NOTE: The NG and LP are deflectors are shaped differently, and the LP has a notch at the bottom. NG (Natural G as )
LP (P ropane)
This notch indicates LP.
4.
Bend up the tab on the burner as shown below. Bend this tab up; it is shipped flat. Page 3 of 10
17601715.docx — 8/8/12
© Travis Industries, Inc.
864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs
Installation Instructions (SKU 96900144)
Special Instructions for LP
Install the rivet included with this kit into the hole shown below.
Andiron Installation (Optional)
The optional andirons should be installed before installing the logs. See the directions below for installation.
1
Remove the grate from the
firebox. Remove and discard
the two andiron prongs (see
step “a” to the right).
NOTE: The nuts do not need to
be removed, they can be
loosened to remove the prongs.
2
Attach the andiron brackets
(shipped with the burner) to the
grate (see step “b”).
3
Attach the andirons using the
screws included with the
andirons (see step “c”).
11/32" Nutdriver
a
b
5/32 Hex
Wrench
c
Page 4 of 10
17601715.docx — 8/8/12
© Travis Industries, Inc.
864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs
Installation Instructions (SKU 96900144)
Log Set Installation
Back Log
Install the back log as shown below. Make sure the bottom of the log lays flat against the two steel
platforms on the burner. Slide the log forward (NG units) or backward (LP units).
Bend this tab up; if not done previously. NG units:
Slide the log forward.
LP units:
Slide the log backward.
Page 5 of 10
17601715.docx — 8/8/12
© Travis Industries, Inc.
864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs
Installation Instructions (SKU 96900144)
Right Log
Install the right log as shown below. Position the log so the back edge contacts the metal plate on the
burner and does not cover any burner holes.
Page 6 of 10
17601715.docx — 8/8/12
© Travis Industries, Inc.
864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs
Installation Instructions (SKU 96900144)
Middle Log
Install the middle log as shown below.
Left Log
Install the left log as shown below.
Page 7 of 10
17601715.docx — 8/8/12
© Travis Industries, Inc.
864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs
Installation Instructions (SKU 96900144)
Left Twig
Install the left twig as shown below.
Right Twig
Install the right twig as shown below.
Page 8 of 10
17601715.docx — 8/8/12
© Travis Industries, Inc.
864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs
Installation Instructions (SKU 96900144)
Center Twig
Install the center twig as shown below.
Page 9 of 10
17601715.docx — 8/8/12
© Travis Industries, Inc.
864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs
Installation Instructions (SKU 96900144)
Ember Installation
Install the embers as shown below. Make sure to cover the screws on the burner and any fireback seams
with embers to create an aesthetic firebox.
Rock Wool Installation
The included rock wool is placed on top of the burner to enhance the glow from the burner. The rock
wool works best when it is applied in a very thin, porous layer. The best method for applying the
rock wool is to brush it on to the burner. Compress a clump of rock wool between your thumb and
forefinger. Use a stiff brush to apply a thin layer of rock wool fibers onto the burner. Do not use the
entire bag of rock wool. Use only a small amount and save the remainder. Over-use of rock wool will
diminish the glow and may cause sooting or other adverse conditions.
Page 10 of 10
17601715.docx — 8/8/12
© Travis Industries, Inc.