F3xDGA Instalation instruction

Transcription

F3xDGA Instalation instruction
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Installation Guide
AWRON Display F36DGA
BMW
•
F36 Gran Coupe
Page:
1
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page:
2
Table of Contents
Table of Contents
2
Scope of delivery
3
Toolkit
4
Cabel system
5
Schematic
6
Installation Guide
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Disassembly interior trim
Disassembly panel under the glove box on passenger side
Disassembly door sill on passenger side
Disassembly side trim on the passenger side
Expose the connector from the FEM control unit
Dismounting plug CON 2
Dismounting plug CON 3
Unpin cable from connector
Pin the cable into the connector
Plug CON 3 into the connector
Remove plug CON 2
Disassembly trim on the passenger side
Plug CON 10 connection
Remove plug CON 10
Support & FAQs
7
9
12
13
14
15
16
17
18
20
21
22
24
25
28
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Scope of delivery
F3xDGA Display module
Power cord set
Page:
3
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page:
Toolkit
Mounting wedge
Assembly tool
Flat screwdriver 2mm
Socket wrench 10mm
Screwdriver TORX T25
2mm
4
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page:
150cm
USB
Cabel system
5
Schematic
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page:
6
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page:
7
Disassembly interior trim
1. Remove with a plastic wedge
strip the interior. Begin from the
right.
2. Pay attention to the connector
on startup button and the
operating unit warning lights, etc.
(see picture below right)
3. Disconnect the connectors,
then you can remove air vent.
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page:
8
Disassembly panel under the glove box on passenger side
Unfolding the screw
Hex, wrench size 8 mm
Unfolding the screw
Hex, wrench size 8 mm
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page:
9
Disassembly panel under the glove box on passenger side
No tools required
Remove connector
No tools required
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page: 10
Disassembly panel under the glove box on passenger side
Remove connector
No tools required
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Disassembly door sill on passenger side
Use a plastic wedge
Unclip side trim
Use a plastic wedge
Page: 11
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Disassembly side trim on the passenger side
Remove the side panel
Use a plastic wedge
Unscrew the cover
Screwdriver TORX T25
Page: 12
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Expose the connector from the FEM control unit
Remove the side panel
No tools required
Remove connector CON2
No tools required
Page: 13
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page: 14
Dismounting plug CON 2
CON10
CON3
CON2
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Dismounting plug CON 2
Unlocking bracket
at the connector
solve
No tools required
Remove connector
No tools required
Page: 15
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Unpin cable from connector (CON 2)
Remowe connector
from the case
Flat screwdriver 2mm
18 = PT_CAN_LOW (rot)
19 = PT_CAN_HIGH (blau/rot)
21 20 19 18 17 16 15 14
19 18
Unpin 18 and 19 Pin
Flat screwdriver 2mm
Page: 16
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Pin the cable into the connector (CON 2)
Pin 1 = PT_CAN_LOW (rot)
Pin 2 = PT_CAN_HIGH
(blau/rot)
Install the supplied white
connector
No tools required
21
14
Cable red and blue / red from
Pin the AWRON cable harness in chamber 18 and 19
No tools required
Page: 17
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Pin the cable into the connector (CON 2)
No tools required
Page: 18
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page: 19
Plug CON 3 into the connector
CON10
CON3
CON2
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Remove plug CON 3
Unlocking bracket
at the connector
solve
Kein Werkzeug notwendig
Remove connector
Kein Werkzeug notwendig
Page: 20
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page: 21
Disassembly trim on the passenger side (CON 3)
Remowe connector from the case
No tools required
20 = Kl.15 (!2V) (braun/grau)
24 = Kl.31 MASSE (braun/schwarz)
19 18
Unpin 20 und 24 Pin
Flachschraubenzieher 2mm
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page: 22
Disassembly trim on the passenger side (CON 3)
Pin 1 = Kl.15 (12V) (grün/grau)
Pin 2 = Kl.31 MASSE (braun/schwarz)
Install the supplied
black connector
No tools required
19 18
Cable green / brown and brown / black from
Pin AWRON cable harness in chamber 20 and 24
No tools required
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page: 23
Plug CON 10 connection
CON10
CON3
CON2
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page: 24
Remove plug CON 10
Unlocking bracket
at the connector
solve
No tools required
Remove connector
19 18
No tools required
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page: 25
Remove plug CON 10
Remowe connector from the case
No tools required
19 18
Unpin Pin 3
Flachschraubenzieher 2mm
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page: 26
Remove plug CON 10
Pin 1 = ETH_WUP (blau/gelb)
Install the supplied
blue connector
No tools required
19 18
No tools required
Installation Guide: F3xDGA
Version: V1.1
Autor:
AWRON GmbH
Datum: 04.05.2016
Page: 27
Support & FAQs
For all enquiries concerning your
AWRON display system, or if you
have problems with installation
guide the AWRON support team
at [email protected] are at your
service.
Please also seen us and our
another AWRON products on
our website www.awron.de

Similar documents

front mount intercooler – part #48.10.95

front mount intercooler – part #48.10.95 11. Remove plastic outside air temp mount from steel bumper then remove sensor from plastic mount. 15. Using a 13mm wrench, unbolt left-side horn from its bracket. Remove OE bracket and using suppl...

More information