SE5 Cover.p65

Transcription

SE5 Cover.p65

SE5
ROTARY MOWER
P/N 00764585MB
Published 01-07
MASTER PARTS BOOK
S/N 00101 TO CURRENT
PARTS LISTING
Rhino®
An Alamo Group Company
1020 S. Sangamon Ave.
Gibson City, Il 60936
1-800-446-5158
Email: [email protected]
© 2007 Alamo Group Inc.
TO THE OWNER/OPERATOR/DEALER
All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who
recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to
be used with all its safety equipment properly attached to minimize the chance of accidents.
BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.
Observe the rules of safety and common sense!
WARRANTY INFORMATION:
Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form
in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card
and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic
failure with possible injury or death.
PARTS
SECTION
Parts Section – 1
PARTS ORDERING GUIDE
The following instructions are offered to help eliminate needless delay and error in processing
purchase orders for the equipment in this section.
1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the
basic machine featured in this manual. Part Numbers and Descriptions are given to help
locate the parts and quantities required.
2. The Purchase Order must include the name and address of the person or organization
ordering the parts, who should be charged, and if possible, the serial number of the machine
for which the parts are ordered.
3. The Purchase Order must clearly list the quantity of each part, the complete and correct part
number (be sure to include all periods), and the basic name of the part.
4. The Manufacturer reserves the right to substitute parts where applicable.
5. Some parts are unlisted items which are special production items not normally stocked and
are subject to special handling. Request a quotation for such parts before sending a
Purchase Order.
6. The Manufacturer reserves the right to change prices without prior notice.
NOTE:
Please refer to The Safety Section in the front of this Manual for the proper
Part Number when ordering Replacement Safety Decals.
For maximum safety and to guarantee optimum product reliability, always use
genuine Servis-Rhino Parts. The use of inferior replacement parts may cause
premature or catastrophic failure which could result in serious injury or death.
Direct any questions regarding parts to:
RHINO ®
Gibson City, IL 60936
800-446-5158
©2007 Alamo Group Inc.
Parts Section – 2
PART NAME INDEX
A-FRAME ASSEMBLY S/N 00101 - 17004 MAR 1984 - SEPT 1993 ................................................................................... 4
A-FRAME ASSEMBLY S/N 17005 - 20080 SEPT 1993 - JUN 1995 .................................................................................... 5
A-FRAME ASSEMBLY S/N 20081 - 32013 JUN 1995 - SEPT 2000 .................................................................................... 6
A-FRAME ASSEMBLY S/N 32014 - CURRENT SEPT 2000 - CURRENT ........................................................................... 7
AXLE ASSEMBLY S/N 13150 - 32013 JUN 1991 - SEPT 2000 ........................................................................................... 8
AXLE ASSEMBLY S/N 32014 - CURRENT SEPT 2000 - CURRENT .................................................................................. 9
BLADE PAN ASSEMBLY S/N 00101 - 13508 MAR 1984 - OCT 1991............................................................................... 10
BLADE PAN ASSEMBLY S/N 13509 - CURRENT OCT 1991 - CURRENT....................................................................... 11
CHAINGUARD ASSEMBLY - FRONT S/N 00101 - 20080 MAR 1989 - JUN 1995............................................................ 12
CHAINGUARD ASSEMBLY - FRONT S/N 20081 - 32013 JUN 1995 - SEPT 2000 .......................................................... 13
CHAINGUARD ASSEMBLY - FRONT S/N 32014 - 40092 SEPT 2000 - OCT 2004.......................................................... 14
CHAINGUARD ASSEMBLY - FRONT S/N 40093 - CURRENT OCT 2004 - CURRENT ................................................... 15
CHAINGUARD ASSEMBLY - REAR S/N 00101 - 13508 MAR 1984 - OCT 1991 ............................................................. 16
CHAINGUARD ASSEMBLY - REAR S/N 13509 - 20080 OCT 1991 - JUN 1995 .............................................................. 17
CHAINGUARD ASSEMBLY - REAR S/N 20081 - 32013 JUN 1995 - SEPT 2000............................................................. 18
CHAINGUARD ASSEMBLY - REAR S/N 32014 - 40092 SEPT 2000 - OCT 2004 ............................................................ 19
CHAINGUARD ASSEMBLY - REAR S/N 40093 - CURRENT OCT 2004 - CURRENT ..................................................... 20
CHECK CHAIN KIT S/N 00101 - CURRENT MAR 1984 - CURRENT................................................................................ 21
DEFLECTOR ASSEMBLY - FRONT S/N 00101 - 20080 MAR 1989 - JUN 1995 .............................................................. 22
DEFLECTOR ASSEMBLY - FRONT S/N 20081 - 25932 JUN 1995 - OCT 1997 .............................................................. 23
DEFLECTOR ASSEMBLY - FRONT S/N 25933 - 32013 OCT 1997 - SEPT 2000 ............................................................ 24
DEFLECTOR ASSEMBLY - FRONT S/N 32014 - 40376 SEPT 2000 - NOV 2004 ............................................................ 25
DEFLECTOR ASSEMBLY - FRONT S/N 40377 - CURRENT NOV 2004 - CURRENT ..................................................... 26
DEFLECTOR ASSEMBLY - REAR S/N 00101 - 13508 MAR 1984 - OCT 1991 ................................................................ 27
DEFLECTOR ASSEMBLY - REAR S/N 13509 - 20080 OCT 1991 - JUN 1995 ................................................................. 28
DEFLECTOR ASSEMBLY - REAR S/N 20081 - 32013 JUN 1995 - SEPT 2000 ............................................................... 29
DEFLECTOR ASSEMBLY - REAR S/N 32014 - CURRENT - SEPT 2000 - CURRENT................................................... 30
DRIVELINE ASSEMBLY - SHEAR BOLT LIFT TYPE S/N 00101 - 11308 MAR 1984 - JAN 1989 ................................... 31
DRIVELINE ASSEMBLY - SHEAR BOLT LIFT TYPE S/N 10947 - 17616 DEC 1989 - JUN 1994.................................... 32
DRIVELINE ASSEMBLY - SHEAR BOLT LIFT TYPE S/N 11309 - 10946 FEB 1989 - DEC 1989.................................... 33
DRIVELINE ASSEMBLY - SHEAR BOLT LIFT TYPE S/N 17617 - 29460 JUN 1994 - JUL 1999..................................... 34
DRIVELINE ASSEMBLY - SHEAR BOLT LIFT TYPE S/N 29461 - 39824 JUL 1999 - AUG 2004 .................................... 35
DRIVELINE ASSEMBLY - SHEAR BOLT LIFT TYPE S/N 39825 - CURRENT AUG 2004 - CURRENT .......................... 36
DRIVELINE ASSEMBLY - SHEAR BOLT PULL TYPE S/N 13150 - 33086 JUN 1991 - MAY 2001.................................. 37
DRIVELINE ASSEMBLY - SHEAR BOLT PULL TYPE S/N 33087 - CURRENT MAY 2001 - CURRENT......................... 38
DRIVELINE ASSEMBLY - SLIP CLUTCH LIFT TYPE S/N 11309 - 14470 JUN 1990 - APR 1992 ................................... 39
DRIVELINE ASSEMBLY - SLIP CLUTCH LIFT TYPE S/N 14471 - 23850 APR 1992 - JAN 1997 ................................... 40
DRIVELINE ASSEMBLY - SLIP CLUTCH LIFT TYPE S/N 23851 - 29179 JAN 1997 - JUL 1999 .................................... 41
DRIVELINE ASSEMBLY - SLIP CLUTCH LIFT TYPE S/N 29180 - 39374 JUL 1999 - SEPT 2004.................................. 42
DRIVELINE ASSEMBLY - SLIP CLUTCH LIFT TYPE S/N 39375 - CURRENT SEPT 2004 - CURRENT ........................ 43
GEARBOX ASSEMBLY S/N 00101 - 29460 MAR 1984 - JUL 1999................................................................................... 44
GEARBOX ASSEMBLY S/N 29461 - 32013 JUL 1999 - SEPT 2000 ................................................................................. 46
GEARBOX ASSEMBLY S/N 32014 - 33447 SEPT 2000 - MAY 2001................................................................................ 48
GEARBOX ASSEMBLY S/N 33448 - CURRENT MAY 2001 - CURRENT ......................................................................... 50
GEARBOX SHIELD ATTACHMENT S/N 00101 - 20080 JUN 1991 - JUN 1995................................................................ 52
GEARBOX SHIELD ATTACHMENT S/N 20081 - CURRENT JUN 1995 - CURRENT....................................................... 53
HYDRAULIC CYLINDER S/N 13150 - CURRENT - JUN 1991 - CURRENT...................................................................... 54
HYDRAULIC LIFT KIT - PULL TYPE S/N 13150 - CURRENT JUN 1991 - CURRENT ..................................................... 55
HYDRAULIC RELIEF ASSEMBLY S/N OBSOLETE - OBSOLETE .................................................................................... 56
LEVEL ROD ASSEMBLY S/N 13150 - CURRENT - JUN 1991 - CURRENT ..................................................................... 57
OFFSET ADAPTER - THREE POINT S/N 00101 - CURRENT MAR 1984 - CURRENT ................................................... 58
SLIP CLUTCH - OBSOLETE S/N 14471 - 32013 APR 1992 - SEPT 2000 ........................................................................ 59
SLIP CLUTCH S/N 11309 - 14470 JUN 1990 - APR 1992 ................................................................................................. 60
SLIP CLUTCH S/N 14471 - 32013 APR 1992 - SEPT 2000 ............................................................................................... 61
SLIP CLUTCH S/N 32014 - CURRENT SEPT 2000 - CURRENT ...................................................................................... 62
TAILWHEEL ASSEMBLY S/N 00001 - 17004 MAR 1984 - SEPT 1993 ............................................................................. 63
TAILWHEEL ASSEMBLY S/N 17005 - 20080 OCT 1993 - JUN 1995................................................................................ 64
TAILWHEEL ASSEMBLY S/N 20081 - 32013 JUN 1995 - SEPT 2000 .............................................................................. 65
TAILWHEEL ASSEMBLY S/N 32014 - 39049 SEPT 2000 - MAY 2004 ............................................................................. 66
TAILWHEEL ASSEMBLY S/N 39050 - 40386 MAY 2004 - NOV 2004............................................................................... 67
TAILWHEEL ASSEMBLY S/N 40387 - 41506 NOV 2004 - FEB 2005................................................................................ 68
TAILWHEEL ASSEMBLY S/N 41507 - CURRENT FEB 2005 - CURRENT ....................................................................... 69
TONGUE ASSEMBLY S/N 13150 - 32013 JUN 1991 - SEPT 2000 ................................................................................... 70
TONGUE ASSEMBLY S/N 32014 - CURRENT SEPT 2000 - CURRENT .......................................................................... 71
SE5 Master Parts Book (01-07)
Parts Section – 3
A-FRAME ASSEMBLY S/N 00101 - 17004 MAR 1984 - SEPT 1993
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
483011A
0891050100
0891050200
0891050300
00750311
00695100
5810126
10318000
00001800
00748823
15B1400
00603500
00603600
00012200
423013
2
1
2
1
1
1
1
1
3
2
2
2
2
2
2
STRAPS A FRAME
A-FRAME, WLDMNT, LINK
LIFT STRAP, SE5
SE5 BUSHING
HEXB,5/8NC X 3-1/2,ZP,GRD5
LOCKNUT TOPLOCK 5/8NC PLB
SPACER
HEXB 1/2NCX3 PL8
LOCKNUT TLM 1/2 NC PLB
HHCS 1/2-13UNC 1-1/2 PL5
WASHER 7/8 SAE P
ASY,CAT.1 HITCH PIN W/LW & NUT
NUT, 7/8 NF HEX PL
LOCKWASHER 7/8 PL STD
BUSHING,PIVOT
Parts Section – 4
A-FRAME ASSEMBLY S/N 17005 - 20080 SEPT 1993 - JUN 1995
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
00764839
00767949
00765331
00757953
02025700
00037200
00001800
00748823
15B1400
00603500
00603600
00012200
2
1
2
1
1
1
3
2
2
2
2
2
BAR, A-FRAME
PLATE-DIVIDER
BAR-LIFT STRAP
BUSHING 1-1/4X7/32X3 A-FRAME
HEXB 3/4 NC 6 PL5
NUT 3/4-NC TOPLOCK GRC PL
HHCS 1/2-13UNC 1-1/2 PL5
WASHER 7/8 SAE P
NUT, 7/8 NF HEX PL
LOCKWASHER 7/8 PL STD
Parts Section – 5
A-FRAME ASSEMBLY S/N 20081 - 32013 JUN 1995 - SEPT 2000
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
00765331
00764839
00757949
00757953
00766587
00766586
00603500
00766086
37107B13
00756105
00762365
00770776
00770772
00770773
37107B12
2
2
1
1
1
1
2
8
1
10
2
8
1
1
1
BAR-LIFT STRAP
BAR, A-FRAME
LINK,TOP
PLATE, HITCH EAR RH
PLATE, HITCH EAR LH
WASHER,12 DIA UNI 6592
CLIP-X HAIR PIN
NUT,TOPLOCK METRIC 12MM-P1.25
HHCS M12x1.25x30 GR8.8
HEXB METRIC 12-P1.25- 40MM
HEXB METRIC 20-P1.5 -140MM PL5
LOCKNUT METRIC 20MM-P1.5
PIN TOP LINK CAT 1(PLATED)
Parts Section – 6
A-FRAME ASSEMBLY S/N 32014 - CURRENT SEPT 2000 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
00765331
00764839
00757949
00757953
00766587
00766586
00603500
00766086
37107B13
00756105
00762365
00770776
00770772
00770773
37107B12
2
2
1
1
1
1
2
8
1
10
2
8
1
1
1
BAR-LIFT STRAP
BAR, A-FRAME
LINK,TOP
PLATE, HITCH EAR RH
PLATE, HITCH EAR LH
CLIP-X HAIR PIN
HEXB METRIC 20-P1.5 -140MM PL5
PIN TOP LINK CAT 1(PLATED)
Parts Section – 7
AXLE ASSEMBLY S/N 13150 - 32013 JUN 1991 - SEPT 2000
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
00761038
02931300
511016
00037200
00753013
00001800
5JRC16140
00765337
0891030300
00756760
0891030200
00761034
00760820
00761046
00761267
00761037
15B1200
1
2
2
2
1
1
2
4
2
2
2
1
1
1
1
1
2
WLDMT-AXLE
HHCS,3/4NC X 2,ZP,GRD5
BUSHING
HHCS 1/2 NC 3 PL8
LOCKNUT 1 -14 TLDT GC ZP
SPACER
WLDMT, SPINDLE w/NUT
WHEEL,DEMOUNTABLE 16X4X2057
TIRE & WHEEL ASSY, SE5 4X8:00
WLDMNT-PIPE ADJ. SUPPORT
NUT, HEX 3/4-10 PLAIN
TRUNION
SPACER
WLDMT-ROD
WASHER 3/4 P SAE
11
12
13
14
15
16
Parts Section – 8
AXLE ASSEMBLY S/N 32014 - CURRENT SEPT 2000 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
00130010
00756760
00765337
0891030300
5JRC16140
00776008
7A16824
02030300
00775963
02918600
15B1200
00037200
00554600
8354
00606000
8527
00775996
02845700
00695100
00775967
00767294
511016
2
2
4
2
2
1
2
2
1
3
3
3
1
1
2
1
2
2
2
1
1
2
WHEEL & TIRE ASSEMBLY - LAMINATED
WHEEL & TIRE ASSEMBLY - SOLID
SPACER
PLATE-AXLE LUG
HHCS 1 NC 3 PL5
NUT TOPLOCK 1 NC PLB
WLDMT AXLE
HEXB 3/4-10UNC 2 PL8
WASHER 3/4 P SAE
ASY,RATCHET JACK
PIN, HYD. CYLINDER
PIN,COTTER 3/16X2
ASY, PIN
FLAT-AXLE CYLINDER LUG
HHCS 5/8 NC 4 PL5
WLDMT-LEVEL ROD
BUSHING, LEVEL ROD
BUSHING
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Parts Section – 9
BLADE PAN ASSEMBLY S/N 00101 - 13508 MAR 1984 - OCT 1991
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
0891040100
0891040300
36107A2ALH
5GL12160
15B1200
1
2
2
2
4
WLDMT,DISHPAN BLADE CARRIER
BLADE, SE5
BOLT SHOULDER
LOCKNUT TLM (LH) 3/4 NF PLB
WASHER 3/4 P SAE
NOTE: Blade bolt (item 3) is a round shoulder blade bolt left hand thread.
Blades and bolts WILL NOT interchange with later production.
Parts Section – 10
BLADE PAN ASSEMBLY S/N 13509 - CURRENT OCT 1991 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
00761358
00761357
00761319
00761402
00761535
00750226
1
2
2
2
2
ASSY-BLADE PAN
WLDMT-BLADE PAN
BLADE-SUCTION SE-5
BLADE BOLT 7/8 DIA X 3 LG
WASHER-7/8 STR PLAIN
NUT TOPLOCK 7/8 NF PLC
NOTE: Blade bolt (item 3) is a round shoulder blade bolt left hand thread.
Blades and bolts WILL NOT interchange with later production.
CHAINGUARD ASSEMBLY - FRONT S/N 00101 - 20080 MAR 1989 - JUN 1995
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
0891101000
0891101100
00752680
0901100102
00001800
0731371001
0731361104
15B800
1
4
2
10
1
51
4
ASSY-CG FRONT RHINO SE5
WLDMT-CG
HHCS 1/2-13UNC X 4LG PL5
MOUNTING FLAT, SE6
CHAIN ROD
CHAIN, 4 LINKS
WASHER 1/2 SAE ZP
CHAINGUARD ASSEMBLY - FRONT S/N 20081 - 32013 JUN 1995 - SEPT 2000
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
00766575
00766576
00766579
00766577
02967385
00766536
00766086
00755881
1
1
51
4
2
4
4
ASY,CHAINGUARD,FRT
WLDMT-CHAINGUARD
ROD 6X1511
CHAIN 4 LINK #8 PROOF COIL
HEXB METRIC 12-P1.75-120MM
FLAT,MOUNT
NUT METRIC TLM 12MM-P1.25 PL5
CHAINGUARD ASSEMBLY - FRONT S/N 32014 - 40092 SEPT 2000 - OCT 2004
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
5
6
7
8
9
10
00775871
00775870
00775869
00756210
0731361104
00756204
00775739
00001400
00695100
00008300
00748823
00001800
1
54
2
2
4
4
4
2
2
ASY MAIN FRT CG
ASY FRONT LH CG
ASY FRONT RH C/G
CHAIN GUARD ROD CYCLONE 60
CHAIN, 4 LINKS
CHAIN GUARD PLATE CYCLONE 60
DEFLECT SIDE FORMED
FLATWASHER 5/8 PL STD
HHCS 5/8 NC 1-3/4 PL5
HHCS 1/2-13UNC 1-1/2 PL5
CHAINGUARD ASSEMBLY - FRONT S/N 40093 - CURRENT OCT 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
00775871
00775870
00775869
00775739
00001400
00695100
02675800
02030700
00001800
1
1
2
4
4
4
2
2
ASY MAIN FRT CG
ASY FRONT LH CG
ASY FRONT RH C/G
DEFLECT SIDE FORMED
HHCS 5/8-11UNC 1-1/2 PL5
HHCS 1/2-13UNC 1-1/4 PL5
CHAINGUARD ASSEMBLY - REAR S/N 00101 - 13508 MAR 1984 - OCT 1991
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
0891111000
0891111100
0891111200
00750959
15B800
00001800
0652100102
0652100104
0731361104
0731361104
1
2
6
6
10
1
2
25
40
SE5 REAR CHAIN GUARD
CHN GD HOLDER ASSY, CTR-SE5
CHAIN, HOLDER ASY SIDE
HEXB,1/2NC X 1,ZP,GRD5
WASHER 1/2 SAE ZP
ROD,CHAINGUARD
ROD CHAIN
CHAIN, 4 LINKS
CHAIN, 4 LINKS
NOTE: The deck is turned downward at 90` in rear of mower where chainguard bolts on.
CHAINGUARD ASSEMBLY - REAR S/N 13509 - 20080 OCT 1991 - JUN 1995
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
00761364
00761365
00761366
00750959
15B800
00001800
00761363
0652130101
1
1
1
6
6
6
3
66
BRKT-CG.REAR CT
BRKT-CG REAR LH
BRKT-CG REAR RH
WASHER 1/2 SAE ZP
ROD-CHAINGUARD
CHAIN, 5/16 PROOF COIL 3 LINKS
NOTE: The rear of deck is at an angle downward approximately 45` where chainguard bolts on.
CHAINGUARD ASSEMBLY - REAR S/N 20081 - 32013 JUN 1995 - SEPT 2000
ITEM
PART NO.
QTY.
DESCRIPTION
5
00766560
00766567
00766564
00766561
00766568
00766566
00766525
00766565
00766562
6
7
8
00756026
00766086
00765966
1
1
1
1
2
24
20
6
6
6
ASSY-CHAINGUARD REAR CTR
ASSY-CHAINGUARD REAR LH
ASSY-CHAINGUARD REAR RH
PLATE-CHAINGUARD REAR CTR
PLATE-CHAINGUARD REAR L/H
PLATE-CHAINGUARD REAR R/H
ROD 6X787
ROD 6X610
CHAIN 3 LINK CTR
CHAIN 3 LINK L/H AND R/H
HHCS M12x1.75x30
NUT MET TLE 12MM-P1.75 PL
1
2
3
4
CHAINGUARD ASSEMBLY - REAR S/N 32014 - 40092 SEPT 2000 - OCT 2004
ITEM
1
2
3
4
5
6
7
8
9
10
PART NO.
QTY.
DESCRIPTION
00775643
00775512
00773667
00773663
00775501
0652100102
0652130101
02030700
00001800
00002700
7B81332
00775653
00775654
1
2 REF
1
1
2
1
48
22
23
17
1
1
1
ASSY, C/G REAR COMPLETE
ASY, REAR CHAINGUARD (INCLUDES ITEMS 3,4 & 5)
WLDMT, LEFT REAR DEFLECTOR
WLDMT, RIGHT REAR DEFLECTOR
FLAT, REAR CHAINGUARD
ROD,CHAINGUARD
CHAIN, 5/16 PROOF COIL 3 LINKS
HHCS 1/2-13UNC 1-1/4 PL5
HHCS 1/2 NC 4
PLATE, RH C/G MOUNT
PLATE, LH C/G MOUNT
CHAINGUARD ASSEMBLY - REAR S/N 40093 - CURRENT OCT 2004 - CURRENT
ITEM
1
2
3
4
5
6
7
8
PART NO.
QTY.
DESCRIPTION
00775643
00775512
00773667
00773663
00775512
02030700
00001800
00002700
7B81332
00775653
00775654
1
2 REF
1
1
2
22
23
17
1
1
1
ASSY, C/G REAR COMPLETE
ASY, REAR CHAINGUARD (INCLUDES ITEMS 3,4 & 5)
ASY, REAR CHAINGUARD
HHCS 1/2-13UNC 1-1/4 PL5
HHCS 1/2 NC 4
PLATE, RH C/G MOUNT
PLATE, LH C/G MOUNT
CHECK CHAIN KIT S/N 00101 - CURRENT MAR 1984 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
3570
8709
8708
02845500
00695100
2
2
2
2
KIT-CHECK CHAIN CAT I
CHAIN, ASY, CARRIER
CARRIER CHAIN ADJUSTMENT STRAP
HEXB 5/8 NC 2 PL5
DEFLECTOR ASSEMBLY - FRONT S/N 00101 - 20080 MAR 1989 - JUN 1995
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
00758340
00758253
02035800
00011100
00011400
00015800
1
9
18
9
9
ASY,DEFLECTOR,FRONT
DEFLECTOR,FRONT RUBBER
WASHER, WOOD, PLATED
FLATWASHER STD 3/8
HEXB 3/8 NC X 1 PL5
LOCKNUT TLM 3/8-NC PLC
DEFLECTOR ASSEMBLY - FRONT S/N 20081 - 25932 JUN 1995 - OCT 1997
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
00770024
00769195
00767282
00762365
00756105
1
1
7
7
ASSY-DEF. FRT
DEFLECTOR, DEBRIS FRONT
BAR-DEFLECTOR STRAP FRT SE5
DEFLECTOR ASSEMBLY - FRONT S/N 25933 - 32013 OCT 1997 - SEPT 2000
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
00773057R
00772760
00772759
00772756
00772732
00772731
00766536
00762365
00756105
02966989
00770783
1
1
1
1
1
2
10
14
4
2
ASY FRONT DEFLECTOR
PANEL FRONT DEFLECTOR
BRACKET FRONT DEFLECTOR
BAR DEFLECTOR STRAP
BRACKET, END - W/90 DEG BEND
PANEL END LEFT
FLAT-MOUNTING
DWG INST VALV CONV BA/SM-BA/SM
WASHER 13IDX 36ODX 3MM PL
DEFLECTOR ASSEMBLY - FRONT S/N 32014 - 40376 SEPT 2000 - NOV 2004
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
00775873
00015800
00011400
00011100
00001400
00695100
00008300
00758240
00775739
02035800
00775875
00748823
00001800
8
8
8
4
4
4
1
2
8
1
2
2
ASY MAIN FRT DEFLECTOR
HEXB 3/8 NC X 1 PL5
FLATWASHER STD 3/8
HHCS 5/8 NC 1-3/4 PL5
BRACKET,MOUNT,FRONT DEFLECTOR
DEFLECT SIDE FORMED
DEFLECTOR PANEL FRONT
HHCS 1/2-13UNC 1-1/2 PL5
DEFLECTOR ASSEMBLY - FRONT S/N 40377 - CURRENT NOV 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
00775873
00015800
00011400
00011100
00001400
00695100
02675800
00758240
00775851
02035800
00778904
02030700
00001800
8
8
8
4
4
4
1
2
8
1
2
2
ASY MAIN FRT DEFLECTOR
HEXB 3/8 NC X 1 PL5
FLATWASHER STD 3/8
HHCS 5/8-11UNC 1-1/2 PL5
BRACKET,MOUNT,FRONT DEFLECTOR
SHEET,SIDE DEFLECTOR
PANEL,RUBBER FRONT DEFLECTOR
HHCS 1/2-13UNC 1-1/4 PL5
DEFLECTOR ASSEMBLY - REAR S/N 00101 - 13508 MAR 1984 - OCT 1991
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
00758341
00758255
00758254
00011100
00011400
00015800
00758578
1
1
12
6
6
2
DEFLECTOR SE5 REAR
FLAP-DEFLECTOR,DEBRIS REAR
BAR-DEFLECTOR (REAR)
FLATWASHER STD 3/8
HEXB 3/8 NC X 1 PL5
BAR,DEFLECTOR REAR SIDE
DEFLECTOR ASSEMBLY - REAR S/N 13509 - 20080 OCT 1991 - JUN 1995
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
00761629
00761633
15B800
00750959
00001800
00761634
00761630
1
1
6
6
6
2
2
SHLD-DEF. RR. CTR
BAR-DEF. STRAP
WASHER 1/2 SAE ZP
BAR-DEF. STRAP
SHLD-DEF. OUTER
DEFLECTOR ASSEMBLY - REAR S/N 20081 - 32013 JUN 1995 - SEPT 2000
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
00762365
00770782
00769192
00769193
00756105
00769194
00769191
6
6
2
2
6
1
1
WASHER 13 IDX 24 ODX 2.5MM PL
SHIELD, DEFLECTOR REAR O/S
BAR, DEFLECTOR STRAP
BAR, DEFLECTOR STRAP
SHIELD, DEFLECTOR REAR CTR.
DEFLECTOR ASSEMBLY - REAR S/N 32014 - CURRENT - SEPT 2000 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
00775510
00773667
00773663
00773659
00773658
02030700
7B81332
00002700
00001800
00775653
00775654
1
1
2
4
22
1
17
23
1
1
ASSY, DEF. REAR COMPLETE
DEBRIS, DEFLECTOR
BAR, REAR STRAP
HHCS 1/2-13UNC 1-1/4 PL5
HHCS 1/2 NC 4
PLATE, RH C/G MOUNT
PLATE, LH C/G MOUNT
DRIVELINE ASSEMBLY - SHEAR BOLT LIFT TYPE S/N 00101 - 11308 MAR 1984 - JAN 1989
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
948122601
940122600
940000001
948000031
948000030
940000000
948002232
940000040
947132709
940132600
940000009
947000031
947000030
940000000
947002232
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
PTO DRIVELINE HALF W/SHIELD
YOKE & SHAFT WELDMENT ASSY
YOKE 1 3/8 - 6 SPL,
FLEX BELL
BEARING, OUTER SHIELD
REPAIR KIT 1800 U JT
SHIELD, PLASTIC OUTER
KIT, QD PIN
HOUSING ASSEMBLY W/SHIELD
YOKE & SHAFT WELDMENT
YOKE, 1800 SHEAR BOLT
BELL, 12 RING FLEX
BEARING, INNER SHIELD
REPAIR KIT 1800 U JT
SHIELD, PLASTIC INNER
NOTE: This D/L has round shaft and tube w/3 crimped ridges on it. Black shields - shear bolt driveline only. No torque
limiter used on these serial numbers. Replace with complete assembly 00759161A. Part WILL NOT interchange.
DRIVELINE ASSEMBLY - SHEAR BOLT LIFT TYPE S/N 10947 - 17616 DEC 1989 - JUN 1994
ITEM
PART NO.
QTY.
DESCRIPTION
1
3
4
6
7
8
9
10
11
13
15
16
17
18
19
22
23
24
27
00759161A
00759177A
00762574
00756005
00756231
00759162
00759517
00759164
00759165
00759166
00759173A
00759171
00756004
00759167
00759168
00759169
00754474
00759170
00762577
00759176A
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
DRIVELINE,CAT3 SE4&SE5 S 40
SHIELD HALF OUTER
BEARING OUTER SHIELD 540
DECAL-ROTATING DRIVELINE
CROSS & BEARING KIT SERIES 40
OUTER YOKE SHEAR BOLT
GREASE FITTING
YOKE INNER TUBE
PIN ROLL INNER TUBE
TUBE INNER
SHAFT, INNER W/PROTECTOR
KIT COLLAR COLLAR, KIT
DECAL-SHIELD MISSING
TUBE, OUTER
YOKE OUTER TUBE
PIN ROLL 8mm X 60mm
PUSH PIN SET
YOKE OUTER WITH QUIC
BEARING,INNER SHIELD 540
SHIELD HALF INNER
NOTE: This D/L has triangle shape tube and shaft with black shields. Parts WILL NOT interchange with previous
drivelines. This is Cat 3 D/L.
Items 1 and 3 must be purchased together, and items 24 and 27 must be purchased together to ensure proper fit.
DRIVELINE ASSEMBLY - SHEAR BOLT LIFT TYPE S/N 11309 - 10946 FEB 1989 - DEC 1989
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
8
9
10
11
12
13
14
15
16
17
18
19
8887
8937
8938
8923
8445
8924
8925
8926
8945
8927
8928
8929
8930
8932
7387
00756004
8936
8942
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
2
DRIVELINE COMPLETE
INNER HALF COMPLETE
OUTER HALF COMPLETE
YOKE - SLIDE COLLAR
Q.D. KIT
YOKE - SHEAR PIN
CROSS & BEARING KIT
YOKE INBOARD
PIN- SPRING
PROFILE INNER
PROFILE OUTER
YOKE INBOARD
CONE, SHIELD
TUBE OUTER SHIELD W/CAP
DECAL, DECK U-JOINT
TUBE INNER SHIELD W/CAP
RING, BEARING
NOTE: This D/L has lemon shape tube and shaft - yellow shields. Replace with complete assembly 00759161A - Parts
WILL NOT interchange.
DRIVELINE ASSEMBLY - SHEAR BOLT LIFT TYPE S/N 17617 - 29460 JUN 1994 - JUL 1999
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
00759161A
00757144
00764500
00756231
00759168
00759169
00768293
00759913
00759165
00759164
00777329
7A81324
00001800
00768342
00764506
00761078A
00764507
7192
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DRIVELINE,CAT3 SE4&SE5 S 40
KIT-SLIDE COLLAR REPAIR
YOKE-SLIDE COLLAR
YOKE OUTER TUBE
PIN ROLL 8mm X 60mm
TUBE, ASY, OUTER
INNER TUBE - WHEN INVENTORY
PIN ROLL INNER TUBE
YOKE INNER TUBE
KIT,SHEAR BOLT YOKE&PROTECTOR
HHCS 1/2NC X 3 PL2 MUST BE GR2
SHIELD, ASY, CMPLT
COLLAR-INNER-GUARD-RETAINER
SHIELD INNER HALF
COLLAR-OUTER-GUARD-RETAINER
SNAP RING 1-1/2 OD X 1-5/16 ID
DRIVELINE ASSEMBLY - SHEAR BOLT LIFT TYPE S/N 29461 - 39824 JUL 1999 - AUG 2004
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
00759161B
00768296
001465
00768257
00756231
00768295
00768294
00768293
00770391
00759170
00764506
00754330
00764507
00775112
00775113
1
1
1
2
1
1
1
1
1
1
6
1
1
1
DRIVELINE
SHAFT, ASY, INNER W/SHIELD
GREASE FITTING,STRAIGHT,M6
YOKE, SHEAR PIN 1-3/8
TUBE, ASY, INNER
SHAFT, ASY, OUTER W/SHIELD
TUBE, ASY, OUTER
KIT,REPAIR-TWIST COLLAR BLACK
BOLT, NYLON - SAFETY SHIELD]
SHIELD, INNER DRIVELINE
SHIELD, OUTER DRIVELINE
DRIVELINE ASSEMBLY - SHEAR BOLT LIFT TYPE S/N 39825 - CURRENT AUG 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
00759161C
00764500A
00756231
--------------00759169
----------------------------00759165
--------------00777329A
00764506
00754330
00764507
00768342
--------------------------------------------------------00768294
00768296
----------------------------00774079
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DRIVELINE,SP SER.40 SE5
ASY,YOKE COLLAR - COMPLETE
OUTER YOKE
PIN ROLL 8mm X 60mm
OUTER TUBE
INNER TUBE
PIN ROLL INNER TUBE
INNER YOKE
YOKE, 1-3/8 BORE SP
SHIELD, ASY, CMPLT
FEMALE TUBE YOKE
MALE TUBE YOKE
HALF FEMALE GUARD
HALF FEMALE GUARD
DANGER LABEL FOR OUTER TUBE
DANGER LABEL FOR OUTER GUARD TUBE
KIT,SLIDE COLLAR REPAIR
DRIVELINE ASSEMBLY - SHEAR BOLT PULL TYPE S/N 13150 - 33086 JUN 1991 - MAY 2001
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
00761057
00761437
00761438
00761439
00761440
00761441
00761442
00761443
00761444
00761445
00761446
7A81324
1
2
1
1
1
1
1
1
1
1
1
DRIVELINE
YOKE-SHEAR PIN EG SER 5
ASSY-CROSS BEARING SER 5 EG#
ASSY-OUTER TUBE&YOKE SER 5 EG#
ASSY-INNER TUBE&YOKE SER 5 EG#
KIT-SLIDE COLLAR SER.5 EG#
ASSY-QD YOKE 1-3/8-6 SER 5 EG#
ASSY-IMP HALF DL COMPT EG#
ASSY-TRAC HALF DL COMPT EG
ASSY-IMP HALF SHIELD COMPT EG#
ASSY-TRAC HALF SHIELD COMPT EG
NOTE: Triangle shape tube and shaft with yellow shields. Pull type optional 3 point standard.
DRIVELINE ASSEMBLY - SHEAR BOLT PULL TYPE S/N 33087 - CURRENT MAY 2001 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
00775835
00775353
00189700
00756934
00775317
00775375
00775838
00775318
00775462
8393
00775463
00759217
00767954
00775836
00775837
1
2
2
1
1
1
1
1
2
1
2
1
1
DRIVELINE 1-3/8-6 540 RPM
YOKE 1-3/8-6 SPLINE ASGE
CROSSKIT 35R U -JOINT KIT 35R
PIN,ROLL 10 X 80
YOKE INBOARD 1B
INNER PROFILE 1B
OUTER PROFILE ZA
YOKE INBOARD 2A
YOKE 1-3/8 RB
BEARING RING
GREASE ZERK
SCREW 1/2 LG #8 PAN
YOKE.Q.D.KIT - PLASTIC
DRIVELINE TRACTOR HALF
DRIVELINE IMPLEMENT HALF
DRIVELINE ASSEMBLY - SLIP CLUTCH LIFT TYPE S/N 11309 - 14470 JUN 1990 - APR 1992
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
7
8
9
10
11
12
13
14
15
16
17
18
19
8888
8937
8966
8923
8445
8910
8925
8926
8945
8927
8928
8929
8930
8932
7387
00756004
8936
8942
1
1
1
1
1
1
2
1
2
1
1
1
2
1
1
1
1
2
DRIVELINE WITH SLIP CLUTCH,
INNER HALF COMPLETE
OUTER HALF COMPLETE
YOKE - SLIDE COLLAR
Q.D. KIT
CLUTCH (S-5, S-6)
CROSS & BEARING KIT
YOKE INBOARD
PIN- SPRING
PROFILE INNER
PROFILE OUTER
YOKE INBOARD
CONE, SHIELD
TUBE OUTER SHIELD W/CAP
DECAL, DECK U-JOINT
TUBE INNER SHIELD W/CAP
RING, BEARING
NOTE: Lemon shape tube and shaft with yellow shields. Replace with assembly 00759318. Parts WILL NOT interchange
between assemblies.
DRIVELINE ASSEMBLY - SLIP CLUTCH LIFT TYPE S/N 14471 - 23850 APR 1992 - JAN 1997
ITEM
PART NO.
QTY.
DESCRIPTION
1
3
4
6
7
8
9
10
11
12
15
16
17
18
19
23
24
27
00759318
00759920A
00762574
00756005
00756231
00762242
00759517
00759164
00759165
00759913
00762241
00769592
00756004
00759914
00759168
00759169
00769591
00762577
00762246
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
DRIVELINE WITH SLIP CLUTCH
SHIELD HALF (OUTER)
DECAL-ROTATING DRIVELINE
CLUTCH 540 1-3/8 SMOOTH BORE
GREASE FITTING
YOKE INNER TUBE
PIN ROLL INNER TUBE
SHAFT, INNER W/PROTECTOR
KIT-TWIST COLLAR NEW DESIGN
OUTER TUBE
YOKE OUTER TUBE
PIN ROLL 8mm X 60mm
YOKE QD TWIST NEW DESIGN 1-3/8
SHIELD INNER HALF
NOTE: Some of the units shipped in 1997/98 were shipped with driveline 00759318 or 00759318A. The only difference
between the two are the slip clutches and shields. Driveline 00759318 has a slip clutch 00762242, and driveline
00759318A has a slipclutch 00773087.
Triangle shape tube and shaft with black shields. Parts WILL NOT interchange with earlier D/L’s. Cat 3 D/L.
DRIVELINE ASSEMBLY - SLIP CLUTCH LIFT TYPE S/N 23851 - 29179 JAN 1997 - JUL 1999
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
00759318A
00757144
00764500
00756231
00759168
00759165
00759914
00759913
00759165
00759164
00773087
00762574
00759920A
00762246
00762577
00773075
00759915A
00762241A
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DRIVELINE W/SLIP CLUTCH
KIT-SLIDE COLLAR REPAIR
YOKE-SLIDE COLLAR
YOKE OUTER TUBE
PIN ROLL INNER TUBE
OUTER TUBE
PIN ROLL INNER TUBE
YOKE INNER TUBE
CLUTCH 1-3/8 BORE, SERIES 40
OUTER SHIELD HALF
SHIELD INNER HALF
SHIELD COMPLETE
DRIVELINE TRACTOR HALF
SHAFT INNER W/PROTECTOR
NOTE: Some of the units shipped in 1997/98 were shipped with driveline 00759318 or 00759318A. The only difference
between the two are the slip clutches and shields. Driveline 00759318 has a slip clutch 00762242, and driveline
00759318A has a slipclutch 00773087.
DRIVELINE ASSEMBLY - SLIP CLUTCH LIFT TYPE S/N 29180 - 39374 JUL 1999 - SEPT 2004
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
4
5
6
7
8
9
10
11
12
13
14
00759318B
00768339
00768340
00756231
00768295
00768294
00768293
00770391
00759170
00764506
00754330
00764507
00768341
00775113
1
1
2
1
1
1
1
1
1
6
1
1
1
DRIVELINE W/SLIP CLUTCH
CLUTCH, SLIP 1-3/8 S/B
TUBE, ASY, INNER
TUBE, ASY, OUTER
KIT,REPAIR-TWIST COLLAR BLACK
SHIELD, ASY, INNER HALF
SHIELD, OUTER DRIVELINE
DRIVELINE ASSEMBLY - SLIP CLUTCH LIFT TYPE S/N 39375 - CURRENT SEPT 2004 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
00759318C
00764500A
00756231
00759169
00774079
00759165
00773087
00764506
00754330
00764507
00768339
00768342
00768294
1
2
1
1
1
1
1
6
1
1
1
1
DRIVELINE SC SER.40 SE5
ASY,YOKE COLLAR - COMPLETE
PIN ROLL 8mm X 60mm
KIT,SLIDE COLLAR REPAIR
PIN ROLL INNER TUBE
SHIELD, ASY, CMPLT
GEARBOX ASSEMBLY S/N 00101 - 29460 MAR 1984 - JUL 1999
GEARBOX ASSEMBLY S/N 00101 - 29460 MAR 1984 - JUL 1999
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
PART NO.
QTY.
DESCRIPTION
0711050100
00563900
00764949
00757683
00564700
00564000
00564600
00564800
00563700
00757682
00564400
00760929
00760928
7192
02956948
00564100
00563500
00564200
00565000
00749508
00758654
00011400
02161100
7A81324
00606000
00758671
7202
00001800
6192
1
1
1
1
1
1
1
3
1
AR
AR
AR
1
4
3
1
1
1
1
1
6
10
1
1
AR
1
1
1
ASY,GEARBOX 71105 W/GREASE
HOUSING, MAIN
CAP,INPUT BEARING I
OUTPUT CAP
INPUT SHAFT
SHAFT, PINION OUTPUT
INPUT GEAR WG #10-30
BEARING BALL 6207 NO
BEARING,40X80X18 620
SPACER, BEARING
SHIM IEG 30 08-004A
GASKET,OUTPUT (0.30)
GASKET,OUTPUT CAP (0.13)
LOCKNUT 5/8 NC PLC
RING,RETAINING IEG W
OUTPUT OIL SEAL IEG
OIL SEAL IEG WW30 05-002
PLUG, HEX HEAD PIPE
PLUG 1/2-14 NPT
PLUG,1/2 PRESSURIZED VENT
HEXB 3/8 NC X 1 PL5
DISH STAR LOCKWASHER 7/16
HHCS 1/2NC X 3 PL2 (MUST BE GR2)
PIN,COTTER 3/16X2
SHIM,0.2 STEEL GEAR BACKLASH
NUT, SLOTTED 1 NF THICK
WASHER WASHER
NOTE: Items 12, 21, and 25 are not included w/Gearbox Assembly.
GEARBOX ASSEMBLY S/N 29461 - 32013 JUL 1999 - SEPT 2000
GEARBOX ASSEMBLY S/N 29461 - 32013 JUL 1999 - SEPT 2000
ITEM
1
2
3
4
5
6
7
8
9
10
11
13
14
15
16
17
18
19
20
22
23
24
26
27
28
PART NO.
QTY.
DESCRIPTION
0711050100
00563900
00764949
00757683
00564700
00564000
00564600
00564800
00563700
00757682
00564400
00760929
00760928
02956948
00564100
00563500
00564200
00565000
00749508
00758654
00011400
02161100
00606000
00758671
7202
6192
00774567
7192
1
1
1
1
1
1
1
3
1
AR
AR
AR
4
3
1
1
1
1
1
6
10
1
AR
1
1
1
1
ASY,GEARBOX 71105 W/GREASE
HOUSING, MAIN
CAP,INPUT BEARING I
OUTPUT CAP
INPUT SHAFT
SPACER, BEARING
SHIM IEG 30 08-004A
GASKET,OUTPUT CAP (0.13)
LOCKNUT 5/8 NC PLC
OUTPUT OIL SEAL IEG
PLUG, HEX HEAD PIPE
PLUG 1/2-14 NPT
PLUG,1/2 PRESSURIZED VENT
HEXB 3/8 NC X 1 PL5
PIN,COTTER 3/16X2
SHIM,0.2 STEEL GEAR BACKLASH
NUT, SLOTTED 1 NF THICK
WASHER WASHER
BAG, 1/2 SHEAR PIN KIT (CONTAINS 6 PINS AND 6 LOCK RINGS)
GEARBOX ASSEMBLY S/N 32014 - 33447 SEPT 2000 - MAY 2001
GEARBOX ASSEMBLY S/N 32014 - 33447 SEPT 2000 - MAY 2001
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
PART NO.
QTY.
DESCRIPTION
00775857P
00775858
00775859
00564600
00564200
00775860
00564100
00775862
00864400
1
1
1
1
1
3
1
VAR
VAR
VAR
VAR
10
10
1
1
1
1
1
1
3
1
2
2
1
1
ASY,GEARBOX
HOUSING,MAIN
CAP,INPUT
SHAFT,INPUT
SPACER,GEAR
GASKET,INPUT (0.30)
GASKET,INPUT (0.13)
AXLE, ASY, LH OB W/BRKT
HEXB METRIC 10-P1.50- 25MM 5
NUT SLOTTED HEX FLG 1-14UNS PL
PIN,COTTER 3/16X2
OUTPUT OIL SEAL IEG
OUTPUT CAP
SPACER, BEARING
WASHER,SEALING,17.8M
LEVEL PLUG M18 X 1.5
BAG, 1/2 SHEAR PIN KIT (CONTAINS 6 PINS AND 6 LOCK RINGS)
00760929
00760828
02161100
9313055
00758692
00606000
00563500
00757683
00757682
00564000
00563700
00564800
00769321
00770737
00774567
7192
GEARBOX ASSEMBLY S/N 33448 - CURRENT MAY 2001 - CURRENT
GEARBOX ASSEMBLY S/N 33448 - CURRENT MAY 2001 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
25
26
27
00775857P
00775858
00775859
00564600
00564200
00775860
00564100
00775862
00780498
00780497
00760929
00760828
00755954
9313055
00758692
00606000
00563500
00757683
00757682
00564000
00563700
00564800
00769321
00770737
7192
7A81324
00001800
1
1
1
1
1
3
1
VAR
VAR
VAR
VAR
10
10
1
1
1
1
1
1
3
1
2
2
1
1
1
ASY,GEARBOX
HOUSING,MAIN
CAP,INPUT
SHAFT,INPUT
SPACER,GEAR
GASKET, INPUT (0.30)
GASKET, INPUT (0.13)
AXLE, ASY, LH OB W/BRKT
LOCKWASHER M10
NUT SLOTTED HEX FLG 1-14UNS PL
PIN,COTTER 3/16X2
OUTPUT OIL SEAL IEG
OUTPUT CAP
SPACER, BEARING
WASHER,SEALING,17.8M
LEVEL PLUG M18 X 1.5
GEARBOX SHIELD ATTACHMENT S/N 00101 - 20080 JUN 1991 - JUN 1995
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7541
7540
00002700
5F8130
00764259
4405
1
1
1
1
1
2
PLATE-SHIELD
BRKT-HOOD
1/2 NC WING NUT
CHAIN
PIN, COTTER 5/32 X 1 PL
NOTE: This shield was not used on all units in earlier production depending on style D/L used.
GEARBOX SHIELD ATTACHMENT S/N 20081 - CURRENT JUN 1995 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
00766581
00766559
00766086
00755881
00770066
1
1
1
1
1
PLATE-SHIELD
BRACKET, HOOD
ASY, CHAIN WITH PIN
HYDRAULIC CYLINDER S/N 13150 - CURRENT - JUN 1991 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
8727
8763
4675M
7339
00023100
00760671
8752
8753
00013901
02031800
8757
8754
8755
8756
1
1
1
1
1
1
1
1
8
1
1
1
4
HYDRAULIC CYLINDER, T
SEAL KIT
NUT PISTON
BREATHER, CYLINDER
HHCS 3/8 -16UNC 1-1/2 PL5
PISTON 2-1/2 BORE
TUBE (HYD. CYLINDER)
PISTON ROD
NUT HEX 3/8 NC PL
NUT HEX 3/8 NF PL
HEAD
CLEVIS,OUTER
CAP (HYD. CYLINDER)
TIE ROD
HYDRAULIC LIFT KIT - PULL TYPE S/N 13150 - CURRENT JUN 1991 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
00770844
8727
00770833
00770834
00770845
00770846
00767293
00748569
8354
02958979
00606000
7329
651132
02957510
00768968
02963531
00037200
03100104
1
1
1
2
1
1
1
2
1
1
1
1
1
2
KIT-HYD LIFT-PULL TYPE AXLE
HYDRAULIC CYLINDER, T
LUG,LEFT
LUG,RIGHT
LUG,BASE
BUSHING
TUBE-SPACER SE6
BUSHING
PIN, HYD. CYLINDER (USE EXISTING PIN)
PIN-CYL 4
PIN,COTTER 3/16X2
ADAPTER,HYD,STRAIGHT 8MP-8FPX
HOSE #6 - 8MP - 8MP - 144LG
HEXB METRIC 16-P1.5 - 90MM 8
HHCS 3/4 NC 3-1/4 PL5
FLATWASHER 3/4 X 1-1/4 X 14GA
NOTE: Items 1 and 12 are not included in kit.
HYDRAULIC RELIEF ASSEMBLY S/N OBSOLETE - OBSOLETE
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
62504
625041
483061
625042
625043
9A1121048
02023900
21600
1
1
1
1
1
1
2
ASSY-HYDRAULIC RELIEF (OBSOLETE)
TOP LINK
WLDMT-CHN RLF
BLOCK, ADJUSTING,HYD HT CONTRL
BUSHING,HYDRAULIC RELIEF
SETSCREW 3/4X6 NC
NUT 3/4 NC HEX PL JAMNUT
SHACKLE (OBSOLETE)
LEVEL ROD ASSEMBLY S/N 13150 - CURRENT - JUN 1991 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
00761056
00760820
00761046
00761267
00761037
02931300
00767294
00037200
15B1200
1
1
1
1
1
1
1
1
1
WLDMT-LEVEL ROD
TRUNION
SPACER
WLDMT-ROD
HHCS,3/4NC X 2,ZP,GRD5
BUSHING, LEVEL ROD
WASHER 3/4 P SAE
OFFSET ADAPTER - THREE POINT S/N 00101 - CURRENT MAR 1984 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
0702310100
0702310001
0702310300
0702310200
511027
7A14924
15B1400
423013
5JRC1490
3W6
1
1
1
1
2
2
4
4
2
2
ADAPTER, 3PT M/F WLDMNT
STBLR
BRACE LUG-CHN WLD
LUG, WLDMNT, LIFT
PIN 7/8 DIA X 4 PLATED
HHCS 7/8 NC 3 PL5
WASHER 7/8 SAE P
BUSHING,PIVOT
NUT TOPLOCK 7/8 NC PLB
PIN, RETAINING
SLIP CLUTCH - OBSOLETE S/N 14471 - 32013 APR 1992 - SEPT 2000
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
00762242
00752902
00756024
00762243
00762244
00762247
00762250
00762252
00762523
00762251
2
8
1
1
1
8
1
8
1
CLUTCH 540 1-3/8 SMOOTH BORE
LINING FF3 SERIES 6
CLUTCH BODY W/1-3/8 BORE
CLUTCH YOKE, 540
FLANGE, OUTER
SPRING
SHIELD, DIRT
LOCKNUT
NOTE: This Slip Clutch is used with D/L 00759318 WIll NOT interchange with earlier torque limiter. Used on 3 point lift
type only.
For replacement part identification please check the inside diameter of the outer flange (item 5). It should be 3-3/4". When
ordering please remember to specify the pressure plate ID.
SLIP CLUTCH S/N 11309 - 14470 JUN 1990 - APR 1992
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
8910
8425
8369
8465
8366
8736
8967
4
2
1
2
1
1
CLUTCH (S-5, S-6)
NUT, HEX 8MM REPL 8370
BELLEVILLE SPRING
THRUST PLATE WALTER
RING,CLUTCH LINING
HUB 1-3/8 RB
CLUTCH HOUSING
NOTE: Item 1 is used for assembly and disassembly of clip clutch - not for adjustments.
SLIP CLUTCH S/N 14471 - 32013 APR 1992 - SEPT 2000
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
00773087
00773080
00773082
00773081
00773083
00773085
00773086
00754316
00773084
1
1
1
1
2
8
8
1
YOKE FLANGED
CLUTCH SUPPORT W/1-3/8 BORE
BUSHING
PRESSURE PLATE
LINING CLUTCH SERIES 40
SPRING
NUT & BOLT M10X80
NUT & BOLT
NOTE: This Slip Clutch is used with D/L 00759318 WIll NOT interchange with earlier torque limiter. Used on 3 point lift
type only.
NOTE: For replacement part identification plese check the inside diameter of the preseeure plate (item 4). It should be 3"
When ordering please remember to specify the pressure plate ID.
SLIP CLUTCH S/N 32014 - CURRENT SEPT 2000 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
00768340
00768349
00756024
00768348
00768347
00768346
00762523
00768345
00768344
1
8
8
2
1
8
1
1
CLUTCH, SLIP 1-3/8 S/B
YOKE, CLUTCH FLANGE
SPRING, CLUTCH 1-3/8 S/B
DISK, CLUTCH
PLATE, CLUTCH PRESSURE
HUB, CLUTCH SUPPORT 1-3/8 S/B
BUSHING, NYLON
TAILWHEEL ASSEMBLY S/N 00001 - 17004 MAR 1984 - SEPT 1993
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
0891030100
00756760
0891030300
5JRC16140
0891020100
00036900
15B2000
10318000
00001800
00750311
00695100
0891030201
02961453
1
1
1
1
1
1
1
2
2
1
1
2
1
WLDMT CASTER FORK
WLDMT T/W BEAM
PIN-COTTER 1/4 X 2-1/2
WASHER SAE 1 1/4 PLATED
HEXB 1/2NCX3 PL8
BUSHING, SINTERED IRON
GREASE FITTING 1/4-28 TAPER 45
NOTE: Semi-solid wheel not used prior to 1990. Will fit earlier units without modification. Check type of tire before
ordering.
TAILWHEEL ASSEMBLY S/N 17005 - 20080 OCT 1993 - JUN 1995
ITEM
PART NO.
QTY.
DESCRIPTION
1
3
4
5
6
7
8
9
10
11
13
14
15
16
17
0891030100
0891030300
5JRC16140
0891020100
00036900
15B2000
10318000
00001800
00750311
00695100
02961453
00765337
00013600
00013701
00756750
1
1
1
1
1
1
2
2
1
1
1
2
2
2
1
WLDMT CASTER FORK
WLDMT T/W BEAM
HEXB 1/2NCX3 PL8
SPACER
SEAL
BEARING CONE 1.0000" ID
TIRE/WHL. W/CUPS(BREAK DOWN
TAILWHEEL ASSEMBLY S/N 20081 - 32013 JUN 1995 - SEPT 2000
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0891020100
02957510
00768968
00766611
00766610
00770781
00770777
02963669
00756105
0891030100
15B2000
00036900
00766603
00765337
00013701
00013600
00130010
00756750
00750621
02961453
1
1
1
1
1
4
4
2
2
1
1
1
1
2
2
2
1
1
2
1
WLDMT T/W BEAM
WDMT, GAUGE WHEEL MOUNT
FLAT, MOUNTING
WLDMT CASTER FORK
WLDMT-SPINDLE LOCK WITH NUT
SPACER
SEAL
ASY,TIRE & WHEEL 4:00 X 8:00
CUP, BEARING
TAILWHEEL ASSEMBLY S/N 32014 - 39049 SEPT 2000 - MAY 2004
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0891020100
02957510
00768968
00766611
00770781
00770777
02963669
00756105
0891030100
15B2000
00036900
00766603
00765337
00013701
00013600
00130010
00756750
02961453
00750621
1
1
1
1
4
4
2
2
1
1
1
1
2
2
2
1
1
1
2
WLDMT T/W BEAM
WLDMT CASTER FORK
SPACER
SEAL
CUP, BEARING
TAILWHEEL ASSEMBLY S/N 39050 - 40386 MAY 2004 - NOV 2004
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
6
7
8
9
10
11
12
13
14
17
0891020100
02957510
00768968
00766611
00770781
00770777
02963669
00755881
00776224
15B2000
00036900
0891030300
00776217
00776210
1
1
1
1
4
4
2
2
1
1
1
1
2
1
WLDMT T/W BEAM
FORK CASTER ASSEMBLY
WASHER FLAT 026 X 044 X 4 FLAT
AG SE CASTER FORK WHEEL ASSY
TAILWHEEL ASSEMBLY S/N 40387 - 41506 NOV 2004 - FEB 2005
ITEM
PART NO.
QTY.
DESCRIPTION
1
3
4
6
7
8
9
10
11
12
13
14
15
16
17
18
21
22
0891020100
00768968
00766611
00770781
00770777
02963669
00755881
0891030100
15B2000
00036900
00766603
00765337
00013701
00013600
00130010
00756750
00756760
00750621
1
1
1
4
4
2
2
1
1
1
1
2
2
2
1
1
1
2
WLDMT T/W BEAM
WLDMT CASTER FORK
SPACER
SEAL
CUP, BEARING
TAILWHEEL ASSEMBLY S/N 41507 - CURRENT FEB 2005 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
6
7
8
9
10
11
12
13
14
17
0891020100
02957510
00768968
00766611
00770781
00770777
02963669
00755881
00776224
15B2000
00036900
0891030300
00776217
00776210
1
1
1
1
4
4
2
2
1
1
1
1
2
1
WLDMT T/W BEAM
FORK CASTER ASSEMBLY
WASHER FLAT 026 X 044 X 4 FLAT
AG SE CASTER FORK WHEEL ASSY
TONGUE ASSEMBLY S/N 13150 - 32013 JUN 1991 - SEPT 2000
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
00766275
7092
7A114916
15B1400
423013
5JRC1490
00764515
02881000
00759275
00037200
1
1
2
2
2
2
1
1
2
1
WLDMT-TONGUE
JACK, TONGUE COMPLETE W/PIN
HHCS 7/8-9 NC 2 PL5
WASHER 7/8 SAE P
BUSHING,PIVOT
CHAIN, SAFETY TOW-6000# CAP.
HHCS 3/4 NC 3-1/2 PL5
WASHER, HITCH CLEVIS
TONGUE ASSEMBLY S/N 32014 - CURRENT SEPT 2000 - CURRENT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
00766586
00766587
00775964
7092
00764515
00761037
00761267
00761046
5JRC1490
00776701
15B1400
02793900
00755881
00766086
00770776
00760820
00775967
1
1
1
1
1
1
1
1
2
2
2
2
8
8
8
1
1
PLATE, HITCH EAR LH
PLATE, HITCH EAR RH
WLDMT-TONGUE
JACK, TONGUE COMPLETE W/PIN
CHAIN, SAFETY TOW-6000# CAP.
WLDMT-ROD
SPACER
TRUNION
BUSHING 1-1/8 x .885 x 1.0 LG
WASHER 7/8 SAE P
HHCS 7/8-9UNC 2-1/2 GR 5
WLDMT-LEVEL ROD
SERVIS-RHINO
LIMITED
WARRANTY
1. LIMITED WARRANTIES
1.01.Servis-Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal
purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”)
that the goods purchased are free from defects in material or workmanship.
1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be
defective under normal use and service due to defects in material or workmanship.
1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use,
negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or
lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal
combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found
in your Operator’s Manual.
1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any
nature on behalf of Manufacturer.
2. REMEDIES AND PROCEDURES.
2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer
within 30 days of purchase.
2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the
goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the
claim is based.
2.03.Purchaser is responsible for returning the goods in question to the Dealer.
2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and
service due to defects in material or workmanship, Manufacturer will:
(a) Repair or replace the defective goods or part(s) or
(b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer)
if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty
by Manufacturer.
The choice of remedy shall belong to Manufacturer.
2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and
for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory.
3. LIMITATION OF LIABILITY.
3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES
WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR
USE OF THE GOODS.
3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO
PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE
CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT
LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM
THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE
ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGES
INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS.
3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER
THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS
OCCURRED.
4. MISCELLANEOUS.
4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County,
Texas.
4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall
be deemed to be a waiver of any other term.
4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the
invalidity of such provision shall not invalidate any other provisions herein.
4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein.
KEEP FOR YOUR RECORDS
ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine
identification when applying for warranty.
Servis-Rhino Implement Model _______________________________ Serial Number ________________________________
Date Purchased __________________________________________ Dealer ______________________________________
ATTENTION:
READ YOUR OPERATOR'S MANUAL
RHINO®
Gibson City, IL 60936
800-446-5158
TO THE OWNER/OPERATOR/DEALER
To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and
the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily
find the information you need.
The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety
requirements of tractor operators:
REQUIRED OF THE OWNER:
1.
2.
3.
4.
Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and
Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and
Ensure that each employee uses such Seatbelt while the tractor is moving; and
Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected
area provided by the ROPS.
REQUIRED OF THE OPERATOR
1.
2.
3.
4.
5.
6.
7.
8.
9.
Securely fasten seatbelt if the tractor has a ROPS.
Where possible, avoid operating the tractor near ditches, embankments, and holes.
Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.
Stay off slopes too steep for safe operation.
Watch where you are going - especially at row ends, on roads, and around trees.
Do not permit others to ride.
Operate the tractor smoothly - no jerky turns, starts, or stops.
Hitch only to the drawbar and hitch points recommended by the tractor manufacturer.
When the tractor is stopped, set brakes securely and use park lock, if available.
Keep children away from danger all day, every day...
Equip tractors with rollover protection (ROPS) and keep all machinery
guards in place...
Please work, drive, play and live each day with care and concern for
your safety and that of your family and fellow citizens.
SE5 PL 01-07
Printed U.S.A.
P/N 00764585MB

SE5 Cover.p65

Transcription

Similar documents

FL20/FL14

part`s manual

REPLACMENT PARTS FOR SHORTLINE SECTION

00764581MB---FM15 FM10 MPB PUB 07-05 Rev 10-11

TURBO 120 MPB PUB 09-05 Rev 11-05

Flex10/Flex15 MAGNUM

TILLER PUB 02-03 Rev 05-07 PARTS