Complete Systems Complete Systems Kits - MIL-SIM

Complete Systems Complete Systems Kits - MIL-SIM

Complete Systems
Kits
MIL-ECH-IMEESS
* A complete training kit including an ECHO system which allows the user a multiple signature detonation
with audio, visual effects and damage assessment
* Includes high output LED strobes for night training
* Can be converted to use as four separate units for daisy chaining
* Includes NEW 27 MHz long range detonator (.5 Mile LOS)
* Self Inventorying
Description
ECHO System IMEESS
Complete Systems
MIL-MCO-IMEESS
* A complete Mounted Convoy Operations training Kit
* Kit includes a number of large tubes, heads, detonators and a supporting Field Supply Box with start up
consumables
* Includes 315 MHz 75mm E-Detonator (500 foot LOS)
* Items to cover a large visual cue, required noise levels and damages assessment
* Includes high output LED strobes for night training
* Self-inventorying
* Steel, powder coated cases
Description
Mounted Convoy Operations IMEESS
MIL-MCO-SCS
A complete start up kit of consumables, service parts and spare parts for the MIL-MCO-IMEESS
* Kit Includes:
1- skid grey FX Powder (Cool Smoke) (936 bottles per skid)
1- skid white Cool Smoke FX Powder (Cool Smoke) (936 bottles per skid)
2500 plastic burst discs
900 - 12gram CO2 cartridges
CO2 Fill Station with 2 weigh scales, tools and spare parts
300 feet of airline in Orange, Tan and Olive Drab colors
Also incluces an assorted supply of airline connectors, repair kits, etc..
Description
MCO IMEESS Support- Site Start up Kit
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –1
Complete Systems
Kits
MIL-URB-IMEESS
* Urban Improvised Munitions Explosive Effects Simulator System
* Comprised of devices that operate on the disposable CO2 cartridge and rubber burst disc platforms
including a distraction device, pipe bombs and suicide vest simulators.
* Contains a variety of detonators including radio controlled (315 Mhz), hard-wire via airline, hacksaw blades
and auxiliary trigger.
* Also included is a supporting Field Supply Box with start up consumables
* Self-inventorying, steel, powder coated cases
Description
Urban Training IMEESS
Complete Systems
MIL-URB-SCS
* A complete start-up kit of consumables, service parts and spare parts for the MIL-URB-IMEESS Kit
* Kit Includes:
5 - Cases of Special FX White Powder
5 - Cases of Special FX Grey Powder
500 - Plastic Burst Discs
500 - Rubber Burst Discs
1200 - 12 gram CO2 cartridges
300 ft of assorted coloured Airline (Tan and Olive Drab)
* An assorted supply of airline connectors, service tools, O-Rings etc
Description
URB IMEESS Startup Kit
MIL-DD-KIT
* Distraction Device Kit with consumables for 50 detonations
* 10 Distraction Devices
* 50 Disposable 12 Gram CO2 Cartridges
* 50 Rubber Burst Discs
* 1 Self inventorying steel powder coated carrying case.
Description
Distraction Device Kit
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –2
Complete Systems
Kits
MIL-120-VBIED
* VBIED simulator Kit Includes:
1 - ARC Head/Male Adapter
1 - 120mm Tube
1 - Base/Firing Actuator
1 - Airline
1 - Airline Clippers
1 - Trigger Command Detonator and
1 - Wooden Case
Description
VBIED Kit
Complete Systems
MIL-E3-KIT
* Includes a variety of interchangeable 2 inch diameter pipe bomb simulators
* Radio controlled (315 MHz) detonation - 500 foot LOS
* Two channel transmitter included
* Machined aluminum, MIL SPEC hard anodized matte finish
* Self-inventorying carry case
* Start up consumables
Description
E3 Kit
MIL-SV1
* Vest has marking rounds capability for damage assessment
* Uses disposable 12 gram CO2 cartridges, plastic burst discs and FX Powder (Cool Smoke)
* Includes 1 Trigger Command Detonator
* Machined aluminum
* MIL SPEC hard anodized matte finish
* Polypropylene webbed harness
Description
Suicide Vest V1 Complete Kit
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –3
Complete Systems
Kits
MIL-SV42
* A two tube suicide vest simulator complete kit
* Tubes have blow forward (right angle) heads to direct powder away from user
* Uses disposable 12 gram CO2 cartridges, rubber burst discs and FX Powder (Cool Smoke)
* Includes 1 Trigger Command Detonator
* Comes with X-Vest and 2 pouches.
Description
Suicide Vest V4.2 Complete Kit
Complete Systems
MIL-SV44
* A four tube suicide vest simulator complete kit
* Tubes have blow forward (right angle) heads to direct powder away from user
* Uses disposable 12 gram CO2 cartridges, rubber burst discs and FX Powder (Cool Smoke)
* Includes 1 Trigger Command Detonator
* Comes with X-Vest and 4 pouches
Description
Suicide Vest V4.4 Complete Kit
MIL-SV4R
* A four tube suicide vest simulator complete kit
* Includes Remote Control Power Pack, E3 Universal Booby Trap Device, Ripcord and Trigger Command
Detonator
* Tubes have blow forward (right angle) heads to direct powder away from user
* Uses disposable 12 gram CO2 cartridges, rubber burst discs and FX Powder (Cool Smoke)
* Comes withX-Vest, 5 pouches and remote control box pouch
Description
Suicide Vest V4.R Complete Kit
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –4
Complete Systems
Kits
MIL-FIL-SYS
Complete Systems
* Complete Fill Station System includes:
1 - Fill Station
1 - Vent Hose Muffler
1 - Vent Hose
2 - Weigh Scale
2 - Adapter Hose Assembly w/ Pin Depress
2 - Adapter w/ Pin Depress
1 - Fill Station Service Kit
1 - Package of 10 Pin Depress O-Rings
1 - Package of 5 Bulk Tank Washers
1 - Tube Silicone Lube
1 - 5/16" Allen Wrench
1 - Adjustable Wrench
10 - Rupture Discs
1 - Plastic Carrying Case
Description
Fill Station Complete Start up Kit
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –5
Detonators
Hardwire via Airline
MIL-12G-TCD
* Detonates any MIL-SIM-FX device
* Uses disposable 12 gram cartridge for initiation
* Command detonation
* Standard issue with suicide vest
* Cast and machined plastic
Description
Trigger Command Detonator
MIL-12G-MFD
Detonators
* Detonates any MIL-SIM-FX device
* Uses disposable 12 gram cartridge for initiation
* Tripwire, Command, Pressure sensitive capabilities
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Multi-Function Detonator
MIL-12G-DMS
* Pressure Release Detonator
* Uses disposable 12 gram cartridge for initiation
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Dead Man’s Switch - Pressure Release Detonator
MIL-12G-PAD
* Pressure Applied Detonator
* 10lb pressure applied detonation
* Uses disposable 12 gram cartridge for initiation
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Pressure Applied Detonator
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –6
Detonators
Radio Controlled
MIL-E3-EFD
* E3 Electronic Firing Device
* Streamlines the functions of MIL-EIPB-EOD, MIL-RX-EFD and MIL-RX-IED into one device
* 2 Channel remote control power pack
* Tripwire capabilities
* External trigger banana jacks
* 315 MHz and 500ft LOS
Description
Electronic Firing Device
MIL-RX-75SK
Detonators
* Single Air Solenoid Trigger and Compressed Air Chamber Set
* Radio controlled detonator with 2 Channel Transmitter
* 315 MHz - 500 Feet LOS
* Allows for two consecutive detonations
* Uses low pressure compressed air for initiation
* Machined aluminum
* MIL SPEC anodized matte finish
Description
75mm E-Detonator
MIL-4CH-RXASK
* ECHO Long Range 4 Channel Receiver
* Compressed Air Chamber with Sure Seal Connectors
* 5 Pin Connector Harness
* External Trigger Inputs-Initiate or cut an improvised firing circuit to trigger detonation
* 4 Channel LED Status Indicators, Battery Status Test Button, On/Off Switch with LED Status Indicator
* 4 Channel/Button Hand Held Transmitter
* Includes Quick Fill Trigger
* Storage Case
* 27 MHz and .5 Mile LOS
Description
Radio Controlled 4 Channel Extended Range Detonator
MIL-4CH-RXAS
* ECHO Long Range 4 Channel Receiver and Transmitter with 5 Pin Connector
* 27 MHz - .5 Mile LOS
* 4 Channel/Button Hand Held Transmitter
* With Normally Open/Normally Closed firing circuit
Compressed Air Chamber - Sold Separately
Description
ECHO Long Range Detonator
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –7
Dismounted Training Devices
External Detonation Devices
MIL-5-105
* Improvised ordnance round for detection / reaction drills
* Anti-personnel training
* Uses disposable 12 gram CO2 cartridge and FX Powder (Cool Smoke)
* Machined aluminum
* MIL SPEC anodized matte finish
Description
105mm IED Threat SIM with 5 inch Tube
Dismounted Training Devices
MIL-5-BMB
* An improvised bomb for detection / reaction drills
* Anti-personnel training
* Uses disposable 12 gram CO2 cartridge and FX Powder (Cool Smoke)
* Machined aluminum
* MIL SPEC anodized matte finish.
Description
Bomb IED Threat SIM with 5 inch Tube
MIL-5-DCP
* Anti-personnel or convoy training
* Uses disposable 12 gram CO2 cartridge and FX Powder (Cool Smoke)
* Machined aluminum
* MIL SPEC anodized matte finish
* Has marking rounds capability for damage assessment
Description
Directional Charge IED Threat SIM with 5 inch Tube
MIL-5-EFP
* Explosively Formed Penetrator Simulator Assembly
* Specifically designed to be used with marking rounds
* 42” marking zone at approximately 25 feet
* MIL SPEC anodized matte finish
Description
Explosively Formed Penetrator Assembly with 5 inch Tube
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –8
Dismounted Training Devices
External Detonation Devices
MIL-5-MTR
* Improvised mortar round for detection/reaction drills
* Anti-personnel training
* Uses disposable 12 gram CO2 cartridge and F/X powder
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Mortar IED Threat with 5 inch Tube
Dismounted Training Devices
MIL-5-NCA
* Improvised ordnance round with nose cone firing actuator for detection / reaction drills
* Anti-personnel training
* Uses disposable 12 gram CO2 cartridge and F/X powder
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Det Cord to Nose Cone IED with 5 inch Tube
MIL-5-RAH
* Uses disposable 12 gram CO2 cartridge and F/X powder
* Anti-personnel training
* Machined aluminum
* MIL SPEC anodized matte finish
* Has marking rounds capability for damage assessment
Description
A.R.C Threat SIM with 5 inch Tube
MIL-5-UXO
* Replica mortar round for detection / reaction drills
* Anti-personnel training
* Uses disposable 12 gram CO2 cartridge and F/X powder
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Mortar UXO Trainer with 5 inch Tube
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –9
Dismounted Training Devices
External Detonation Devices
MIL-PB-RAH
* A short pipe bomb simulator
* Requires external detonation device
* Uses rubber burst discs
* Uses FX Powder (Cool Smoke)
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Pipe Bomb Tube with Right Angle Head
Dismounted Training Devices
MIL-PBST-S
* A short pipe bomb simulator
* Requires external detonation device
* Uses rubber burst discs
* Uses FX Powder (Cool Smoke)
* Machined aluminum
* MIL SPEC anodized clear coat finish
Description
Pipe Bomb SIM Tube (Short)
MIL-RB-SQB
* A small explosion simulator
* Requires an external detonation device
* Magnetic bottom
* Uses rubber burst discs
Description
Magnetic Squib
Internal Detonation Devices
MIL-DD-SIM
* Distraction Device Simulator
* Uses disposable 12 gram CO2 cartridge
* Creates an audible report
* Used for dynamic entry training
* Aluminum body with MIL SPEC anodized matte finish
Description
Distraction Device Simulator
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –10
Dismounted Training Devices
Internal Detonation Devices
MIL-DD-SIM2
* Distraction Device Simulator with Powder Cavity for Visual Effect
* Uses disposable 12 gram CO2 cartridge
* Creates an audible and visible report
* Used for dynamic entry training
* Aluminum body with MIL SPEC anodized matte finish
Description
Distraction Device Simulator with Powder Cavity
Dismounted Training Devices
MIL-DMS-IED
* Low Profile - Pressure Release Detonation
* Uses disposable 12 gram CO2 cartridge
* Creates an audible report
* Aluminum body with MIL SPEC anodized matte finish
Description
Dead Man Switch Improvised Explosive Device Simulator
MIL-LM
* Equipped with 6 drain holes which prevent water build up inside the head during extended deployment
* Uses disposable 12 gram CO2 cartridge, Plastic Burst Disc and FX Powder (Cool Smoke)
* Can be quickly converted from pressure applied to pressure release by changing the pierce pin plug (included).
* Includes plug removal tool
Description
Landmine
MIL-LM-TC6
* TC/6 Anti-Tank Mine Simulator
* MIL-LM uses disposable 12 gram CO2 cartridge, Plastic Burst Disc and FX Powder (Cool Smoke)
* Can be quickly converted from pressure applied to pressure release by changing the pierce pin plug (included).
* Includes plug removal tool
Description
TC6 Anti-Tank Mine Simulator
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –11
Dismounted Training Devices
Internal Detonation Devices
MIL-PB-TW
*A single Trip Wire Pipe Bomb simulator
* Internal Detonation
* Uses rubber burst discs
* Uses FX Powder (Cool Smoke)
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Tripwire Initiated Pipe Bomb
Dismounted Training Devices
MIL-PB-TWS
* Two Trip Wire Pipe Bomb Simulators in Magnetic Caddy
* Internal Detonation
* Uses rubber burst discs and FX Powder (Cool Smoke)
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Tripwire Initiated Pipe Bomb Set
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –12
Mounted Training Devices
E4 Family
MIL-E4
* Designed for rugged training conditions, the streamlined E4 combines MIL-SIM-FX's Firing Actuator,
Compressed Air Chamber and IED effect simulator in one compact buriable device.
* 60 inch bare wire leads
Description
Electrically Initiated Buriable Device- with Bare Wire Leads
MIL-E4-1
Mounted Training Devices
* Designed for rugged training conditions, the streamlined E4-1 combines MIL-SIM-FX's Firing Actuator
Compressed Air Chamber and IED effect simulator in one compact buriable device.
* 60 inch banana plug leads
Description
Electrically Initiated Buriable Device- with Banana Plugs Leads
ECHO System
MIL-ECHO-1
* ECHO System with built in ILLUM-FX for night training
* Includes:
4 - ECHO Devices (heads sold separately)
1 - 4 Solenoid Compressed Air Chamber with 5 pin connector
1 - 5 Cell Caddy
2 - Ground Stakes
Description
ECHO System
External Detonation Devices
MIL-120-DCP8
* Includes 2 - 8 Inch Ground Stakes
* Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 44 oz)
* Machined aluminum
* MIL SPEC anodized matte finish
* Has marking rounds capability for damage assessment
Description
Directional Charge with 120 mm Tube
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –13
Mounted Training Devices
External Detonation Devices
MIL-20-105
* Improvised ordnance round for detection / reaction drills
* Mounted or dismounted convoy training
* Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz)
* Machined aluminum
* MIL SPEC anodized matte finish
Description
105mm IED Threat SIM with 20 inch Tube
MIL-20-BMB
Mounted Training Devices
* Improvised bomb for detection / reaction drills
* Mounted or dismounted convoy training
* Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz)
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Bomb IED Threat SIM with 20 inch Tube
MIL-20-CBA
* Non-directional concussive effects device used to achieve a significant audio signature
* Consumable platform used is P.E.T. beverage (pop/soda) bottles
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Concussive FX IED Threat SIM with 20 inch Tube
MIL-20-DCP6
* Mounted or dismounted convoy training device
* Includes 2 - 6 Inch Ground Stakes
* Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz)
* Machined aluminum
* MIL SPEC anodized matte finish
* Has marking rounds capability for damage assessment
Description
TC6 Anti-tank Mine Simulator
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –14
Mounted Training Devices
External Detonation Devices
MIL-20-DCP8
* Mounted or dismounted convoy training device
* Includes 2 - 8 Inch Ground Stakes
* Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz)
* Machined aluminum
* MIL SPEC anodized matte finish
* Has marking rounds capability for damage assessment
Description
Directional Charge with 20 inch Tube
Mounted Training Devices
MIL-20-FHA
* IED Threat Simulator with 180 degree Spray pattern
* Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz)
* Machined aluminum
* MIL SPEC anodized matte finish
Description
IED Threat SIM- 180 Degree with 20 inch Tube
MIL-20-MTR
* Improvised mortar for detection / reaction drills
* Mounted or dismounted convoy training
* Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz)
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Mortar IED Threat SIM with 20 inch Tube
MIL-20-NCA
* Improvised ordnance round with nose cone firing actuator for detection / reaction drills
* Mounted or dismounted convoy training
* Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz)
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Det Cord to Nose Cone IED with 20 inch Tube
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –15
Mounted Training Devices
External Detonation Devices
MIL-20-RAH
* Improvised claymore for detection / reaction drills
* Has marking rounds capability for damage assessment
* Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz)
* Machined aluminum
* MIL SPEC anodized matte finish
Description
IED Threat SIM with 20 inch Tube
MIL-20-UXO
Mounted Training Devices
* Replica mortar round for detection / reaction drills
* Mounted or dismounted convoy training
* Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz)
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Mortar UXO Trainer with 20 inch Tube
Improvised Mortar Simulators
MIL-MTR-DFLTAS
* Improvised Mortar Round Launch Tube and Base Set
* Drop Fired Mortars
* Includes:
1 - Launch Tube
1 - Base Assembly
8 - Drop Fired Rounds
1 - Carrying Case
Description
Improvised Mortar System - Drop Fired
MIL-MTR-RFLTAS
* Improvised Mortar Round Launch Tube and Base Set
* Remote Fired Mortar
* Includes:
1 - Launch Tube
1 - Base Assembly
1 - Remote Fired Round
Description
Improvised Mortar System - Remote Fired
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –16
Mounted Training Devices
Improvised Mortar Simulators
MIL-MTR-RFLTS
* Improvised Mortar Round Launch Tube System
* Remote Fired Mortar
* Includes:
1- Launch Tube
1- Remote Fired Round
Description
Improvised Mortar Round
Mounted Training Devices
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –17
Refillable Bottles
C02 Bottles and HPA Bottles
MIL-35-HPN
* Refillable high pressure bottle with high flow valve
* Includes magnetic thread/pin protector cap
* Light weight alloy steel cylinder
* Machined brass
Description
35 Cubic Inch - 1800 PSI High Pressure Bottle
MIL-9R-HFV
Refillable Bottles
* Refillable high pressure bottle with high flow valve
* Includes magnetic thread/pin protector cap
* Light weight alloy steel cylinder
* Machined brass
Description
High Pressure Bottle with High Flow Valve
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –18
Inert
Inert Training Devices
MIL-155-ICAR
* Inert training round
* Light weight aluminum cast
* Olive drab powder coat finish
Description
155mm Inert Cast Aluminum Rounds
MIL-155-PET
* Works with Non-Directional Concussive FX System
* Window adds shape charge directional capability when detonating PET bottles
* Light weight aluminum cast
* Olive drab powder coat finish
Description
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Inert
150mm Concussive FX VISMOD
Page –19
Consumables
Airline
MIL-GRN-100
* Green airline used to connect detonator with device
* Par flex 1/8 O.D. x .031 wall nylon 500 WP line
Description
Olive Drab Airline
MIL-ORG-100
* Orange airline used to connect detonator with device
* Par flex 1/8 O.D. x .031 wall nylon 500 WP line
Description
Orange Airline
Consumables
MIL-TAN-100
* Tan airline used to connect detonator with device
* Par flex 1/8 O.D. x .031 wall nylon 500 WP line
Description
Tan Airline
Burst Discs
MIL-PBD-2500
* Case of 2500 Plastic burst discs
* Molded plastic
Description
Plastic Burst Discs
MIL-RBD-500
* Bag of 500 rubber burst discs
* Bulk purchase pricing
Description
Ruber Burst Discs
MIL-RBD-1000
* Case of 1000 rubber burst discs
* Bulk purchase pricing
Description
Rubber Burst Discs
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –20
Consumables
Burst Discs
MIL-GBD-250
* Bag of 250 thermoplastic burst discs
* Fragment free
* Considerably louder than the standard black rubber burst disc
Description
Thermoplastic Burst Disc - Green
PET Bottles
MIL-PET-500
* 500 ML PET (Polyethylene Terephthalate) plastic bottle
* Used with the Concussive FX Bottle Adapter , Concussive FX IED Threat SIM and the CFX System
* New, Non-Recycled Plastic
* Recyclable
Consumables
Description
PET Plastic Bottle
C02 Cartridges
MIL-C02-300
* Case of 300 cartridges
* 12 gram liquid CO2
* Disposable formed plated steel cartridge
* Authorized for use with MIL-SIM-FX products
Description
Disposable CO2 Cartridges
Powder
MIL-GRY-CS
* Grey FX Powder (Cool Smoke) used to simulate the visual cloud effect of an explosion
* Ground Talc Powder
* Case of 12 - 22 oz bottles
Description
Cool Smoke - Special FX Powder- Grey
MIL-GRY-SKD
* Grey FX Powder (Cool Smoke) used to simulate the visual cloud effect of an explosion
* Non-scented ground talc powder
* Skid of 78 cases (936 - 22 oz bottles)
Description
Cool Smoke - Special FX Powder- Grey
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –21
Consumables
Powder
MIL-WHT-CS
* White FX Powder (Cool Smoke) used to simulate the visual cloud effect of an explosion
* Ground Talc Powder
* Case of 12 - 22 oz bottles
Description
Cool Smoke - Special FX Powder- White
MIL-WHT-SKD
* White FX Powder (Cool Smoke) used to simulate the visual cloud effect of an explosion
* Non-scented ground talc powder
* Skid of 78 cases (936 - 22 oz bottles)
Description
Cool Smoke - Special FX Powder- White
Consumables
Marking Rounds
MIL-68-FO
*Yellow Marking rounds used in some of the MIL-SIM-FX IED devices
* Gel cap filled with non-toxic, non staining paint filler
Description
Fluorescent Orange Color Paint Pallets
MIL-68-FY
* Orange Marking rounds used in some of the MIL-SIM-FX IED devices
* Gel cap filled with non-toxic, non staining paint filler
Description
Fluorescent Yellow Color Paint Pallets
Dry Lubricant
MIL-PTFE
* Dry lubricant used for lubing the threads of the MIL-SIM-FX IED devices
* Contains - Hexane, Propanone, Propane/isobutane/w-butane blend, Toluene, Tetrafluroethylene
Description
PTFE Dry Lubricant
MIL-PTFE-CS
* Case of 12
* Dry lubricant used for lubing the threads of the MIL-SIM-FX IED devices
* Contains - Hexane, Propanone, Propane/isobutane/w-butane blend, Toluene, Tetrafluroethylene
Description
PTFE Dry Lubricant - Case of Twelve
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –22
75mm EDet Support Items
75mm EDet Support
MIL-75S-BJS
* Replacement Banana Jacks for the MIL-RX-75
* Set of Two - One Black, One Red
* Flush fitting - won't snap off
* Plastic
Description
Flush Fitting Banana Jack Set (Black/Red)
MIL-BP-4S
75mm EDet Support Items
* Set of four red and four black banana plugs
Description
Set of Banana Plugs
MIL-75S-CCA
* Circuit Card Replacement
Description
75mm E-Detonator Circuit Card Assembly
MIL-GAUGE-160PSI
* 160 PSI pressure custom gauge
* Color coded to identify minimum and maximum
operating pressures
* Polycarbonate window, stainless steel construction
Description
Pressure Gauge
MIL-RX-75
* Radio controlled (315Mhz) detonation (100m LOS)
* Initiate any 12 volt device
* Two channel transmitter included
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
2 Channel Radio Controlled Receiver (315 MHz)
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –23
75mm EDet Support Items
75mm EDet Support
MIL-EC-ET
* Replacement End Cap for the MIL-RX-75
* Machined aluminum
* MIL SPEC hard anodized matte Clear Coat finish
Description
2 Channel Radio Receiver (315 MHz) End Cap with Wiring Harness
MIL-EC-ETCB
75mm EDet Support Items
*Replacement End Cap and Circuit Board for the MIL-RX-75
* Includes circuit board
* Machined aluminum
* MIL SPEC hard anodized matte Clear Coat finish
Description
2 Channel Radio Controlled Receiver (315 MHz) End Cap with Wiring Harness and Circuit Board
MIL-ILLUM-FX
* High output LED strobe for night training
* 2 LED lights mounted on a steel powder coated base with magnetic feet
Description
Illumination FX- High Output LED Strobe
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –24
Airline Support Items
Airline Support Items
MIL-01-AC
* Airline clippers with lanyard
* Plastic, mould with stainless steel cutting blade
Description
Airline Clippers
MIL-18-1032-ACK
* Package of 10 - 1/8" x 10/32" airline connectors
* Push lock connection
* Plated brass with nylon part
Description
Airline Support Items
Airline Connectors 1/8 x 10/32
MIL-18-18-ACO
* Package of 10 stainless steel airline connectors
* All stainless steel construction
Description
Steel Collar Airline Connectors 1/8 x 1/8
MIL-18-18-KIT
* 100 Steel Airline Connectors
* 5 Collar Unlock Tools
* Plasma cut C10-18 hot rolled mild steel wrench with blue powder coat finish
* 1/8 X 1/8" Stainless steel airline connectors
Description
Airline Connector/Tool Kit
MIL-18-AC10K
* Package of 10 - 1/8" x 1/8" standard airline connectors
* Push lock connection
* Plated brass with nylon part
Description
Airline Connector 1/8 X 1/8
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –25
Airline Support Items
Airline Support Items
MIL-18-AECK
* Package of 5 - 90 degree airline connectors
* Plated brass with nylon part
Description
Airline "Elbow" Connector Kit
MIL-18-AJK
* Package of 5 airline connectors used for joining two airlines together
* Plated brass with nylon part
Description
Airline Support Items
Airline Junction Kit
MIL-18-ATCK
* A package of 5 - "T" airline connectors used for daisy chaining two or more devices together
* Plated brass with nylon part
Description
Airline "T" Connector Kit
MIL-4-WAY
* Airline fitting used for daisy chain detonations when activating up to 4 individual devices
Description
Daisy Chain Fitting
MIL-AC-COMBO
* A steel combination wrench to remove airline and airline connectors
* Plasma cut C10-18 hot rolled steel
* Blue powder coat finish
Description
Combination Collar Unlock Tool and 1/2 inch Wrench
MIL-AC-DBGK
* Package of 10 airline connector protectors
* Rubber device used to protect the airline connectors of the MIL-SIM-FX devices
* High temperature silicone rubber
Description
Airline Connector Dust Boots
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –26
Bases
Bases
MIL-12G-SB
* A base for any 12 gram Firing actuator
* Includes 12 gram CO2 Cartridge Housing
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
12 Gram Cartridge Base
MIL-9R-SB
* A base for any 9oz firing actuator
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Bases
9 Ounce Tank Base
Page –27
Basic Tools
Basic Tools
MIL-1B-SWS
* Single High Quality Strap Wrench
* Molded plastic and rubber
Description
High Quality Strap Wrench
MIL-2-SWS
* A set of Good Quality Strap Wrenches
* Molded plastic and rubber
Description
Strap Wrench Set
MIL-38T-AW
Basic Tools
* 3/8" T-handle Allen wrench
* Treated, forged steel alloy tool
Description
3/8 inch T-Handle Allen Wrench
MIL-532T-AW
* 5/32" T-handle Allen Wrench
* Treated, forged steel alloy tool
Description
5/32 inch T-Handle Allen Wrench
MIL-516T-AW
* 5/16" T-Handle Allen Wrench used to service the CO2 Fill Station
* Forged steel
Description
5/16 inch T-Handle Allen Wrench
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –28
Basic Tools
Basic Tools
MIL-EFD-RTK
* Tool kit for repairing/servicing the MIL-RX-EFD
* Includes:
1 - 7/16" T-Handle Allen Wrench
1 - 5/32" T-Handle Allen Wrench
1 - Pair of Soft Jaw Pliers
Description
EFD Repair Tool Kit
MIL-FSW
Basic Tools
* Fill Station Wrench
* Used to attach/remove valve to tank
* Steel powder coated
Description
Fill Station Wrench
MIL-12-AW
* 12" Adjustable Wrench
Description
Adjustable Wrench
MIL-THN-D
* Used to remove SS Fasteners from the 5 cell caddy
* Also used to remove airline connectors
* A steel ½" x 6" point socket T-Handle wrench
* Powder-coated blue
Description
T-handle Nut Driver
MIL-SPN
* Measuring spoon for measuring FX Powder (Cool Smoke)
* Stainless Steel
Description
Measuring Spoon
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –29
Basic Tools
Basic Tools
MIL-6-SJS
* Magnetic Soft Jaws for Vice Grip
* Rubber pads prevent damage to any of products when using a bench vice grip
* Magnetic so they stay in place
Description
Soft Jaw Set
MIL-SO-TWS
* Inch pound torque wrench used for servicing High Flow Valves
* Includes 6 point - 3/8" drive
* High grade stainless tooling steel
Description
Basic Tools
Dial Torque Wrench with Drive Socket
MIL-375-6PT
* 3/8" x 3/8" Socket-6 Point- 3/8" drive
* Replacement socket for the MILSO-TWS
Description
6 Point Socket
MIL-BPH
* Ball Peen Hammer used to service High Flow Valve bottle
Description
Ball Peen Hammer
MIL-HFV-BP
* Brass Punch used to service High Flow Valve bottle
Description
Brass Punch
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –30
C02 and HPA Bottle Support Items
C02 and HPA Bottle Support Items
MIL-41010-ORK
* Package of 10
* Urethane O-Rings used on the High Pressure Bottle, ECHO Set Plug and ECHO Firing Indicator
Description
Urethane O-ring
MIL-BTL-CAP
C02 and HPA Bottle Support Items
* High Pressure Bottle valve thread protector cap
* Blue aluminum cap
Description
Valve Cap (Blue Aluminum)
MIL-HFV-MEC
* HFV bottle thread/pin protector cap
* Magnetic
* Machined aluminum, olive drab anodized finish
Description
Green Magnetic Bottle Valve Cap
MIL-LIQ-MEC
* HFV bottle thread/pin protector cap
* Magnetic
* Machined aluminum, light blue anodized finish
Description
Blue Magnetic Bottle Valve Cap
MIL-HFV-RDK
* Package of 10 replaceable rupture disc for the 9oz CO2 tank high flow valve
* Machined brass, copper insert
Description
Tank Rupture Discs
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –31
C02 and HPA Bottle Support Items
C02 and HPA Bottle Support Items
MIL-SO-TWS
* Inch pound torque wrench used for servicing High Flow Valves
* Includes 6 point - 3/8" drive
* High grade stainless tooling steel
Description
Dial Torque Wrench with Drive Socket
C02 and HPA Bottle Support Items
MIL-375-6PT
* 3/8" x 3/8" Socket-6 Point- 3/8" drive
* Replacement socket for the MILSO-TWS
Description
6 Point Socket
MIL-BPH
* Ball Peen Hammer used to service High Flow Valve bottle
Description
Ball Peen Hammer
MIL-HFV-BP
* Brass Punch used to service High Flow Valve bottle
Description
Brass Punch
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –32
Caddies and Cases
Caddies
MIL-2-CC
* A two holster caddy used for the 75mm E-Detonator
* 3" Diameter Cells
* Steel powder coated green
Description
3 inch Cell Caddy
MIL-2-CC2
* A two holster caddy with magnetic feet
* 2" Diameter Cells
* Steel powder coated green
Caddies and Cases
Description
2 inch Cell Caddy
MIL-5-CC
* Five Cell Caddy
* Powder coated steel
Description
Five Cell Caddy
MIL-75S-RB
* Replacement rubber bumper
* Includes Washer and Screw
Description
Rubber Bumper
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –33
Caddies and Cases
Cases
MIL-15-TC
* A wooden case used for carrying 15 CO2 tanks
* ¾" pressure treated wood
* Green all weather stain
* Plated steel carry handles
Description
CO2 Tank Case
MIL-08-SC
Caddies and Cases
* A wooden case used for carrying 8 20inch MIL-SIM-FX tubes
* ¾" pressure treated wood
* Green all weather stain
* Plated steel carry handles
Description
Eight Pocket Case
MIL-120-SPC
* A wooden case used for carrying one 120mm MIL-SIM-FX tube
* ¾" pressure treated wood
* Green all weather stain
* Plated steel carry handles
Description
Single 120mm Case
MIL-120-DPC
* A wooden case used for carrying two 120mm MIL-SIM-FX tubes
* 3/4" pressure treated wood
* Grenn all weather stain
* Plated steel carrying handles
Description
Double 120mm Case
MIL-FSB-S
* Used for MIL-SV1; MIL-SV22;MIL-SV24; MIL-SV32, MIL-SV34; and MIL-75S
* Plastic
Description
Small Field Supply Box
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –34
Caddies and Cases
Cases
MIL-FSB-M
* Used for MIL-RD-KIT, MIL-FIL-SYS, and MIL-ECH-RX4
* Plastic
Description
Medium Field Supply Box
MIL-FSB-L
* Used for MIL-ECH-RXL4, MIL-RXL-1CHS, MIL-RXL-4CHS
* Plastic
Description
Caddies and Cases
Large Field Supply Box
MIL-IMEESS
* A case used for carrying the MIL-SIM-FX devices.
* Hot rolled mild steel
* Spot welded and full weld construction
* Green powder coat finish
* Dense ULB charcoal ester foam inserts
Description
IMEESS Case- Metal with Custom Foam Insert
MIL-FSB
* A case used for carrying the items that support the MIL-SIM-FX devices
* Hot rolled mild steel
* Spot welded and full weld construction
* Green powder coat finish
Description
Steel Field Supply Box
MIL-UDO-CS
* Urban Dismounted Operations Case
* Custom cut foam insert
* Hot rolled mild steel
* Spot welded and full weld construction
* Green powder coat finish
Description
UDO Case
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –35
Caddies and Cases
Cases
MIL-UDOX-CS
* Urban Dismounted Operations with Extended Capabilities Case
* Custom cut foam insert
* Hot rolled mild steel
* Spot welded and full weld construction
* Green powder coat finish
Description
UDOX Case
MIL-DD-BX
Caddies and Cases
* A case for used for carrying 10 MIL-DD-SIM as well as support items
* Hot rolled mild steel
* Spot welded and full weld construction
* Green powder coat finish
Description
Distraction Device Box
MIL-SP-OB
* Organizer Box for service parts
* Plastic
Description
Service Parts Organizer Box
MIL-SP-OBS
* Small Organizer Box for service parts
* Plastic
Description
Small Service Parts Organizer Box
MIL-12G-CT
* A tray that holds disposable 12 gram CO2 cartridges
* Holds up to 50 cartridges
* Plastic
Description
12 gram CO2 Cartridge Tray
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –36
Caddies and Cases
Cases
MIL-MCO-GSS
* Set of Two
* Replacement Gas Struts for the Large IMEESS Case
Description
Gas Spring Strut for the MCO-IMEESS Case
MIL-UDOX-GSS
* Set of Two
* Replacement Gas Struts for the Small IMEESS Case
Description
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Caddies and Cases
Gas Spring Strut for the UDO-IMEESS Case
Page –37
Compressed Air Chamber / Solenoid Support Items
Compressed Air Chamber/Air-Solenoid Trigger
MIL-CH-ASK
* Replacement solenoid kit for the MIL-RX-75S
* Kit includes: 1 Solenoid/wiring harness/banana jacks, 2 Screws, 1 O-Ring, 1 Airline Connector, 1 Blue Thread Locker Capsule
Compressed Air Chamber / Solenoid Support Items
* 14 inch lead
Description
Short Leads with Banana Plugs
MIL-1SOL-KIT
* Replacement solenoid kit for the Compressed Air Chamber
* Kit includes: 1 Solenoid/wiring harness/banana jacks, 2 Screws, 1 O-Ring, 1 Airline Connector, 1 Blue Thread Locker Capsule
* 60 inch lead
Description
Long Leads with Banana Plugs
MIL-SV2-AT
* Two Air-Solenoid Trigger/Compressed Air Chamber with Banana Plugs
* Detonates any MIL-SIM-FX device
* Initiated by any 12 volt .5 amp output
* Uses low pressure (100 psi) CO2 or compressed air for initiation
* Includes pressure gauge and fill valve
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Two Air-Solenoid Compressed Air Chamber
MIL-SV4-AT
* Four Air-Solenoid Trigger/Compressed Air Chamber with Banana Plugs
* Detonates any MIL-SIM-FX device
* Initiated by any 12 volt .5 amp output
* Uses low pressure (100 psi) CO2 or compressed air for initiation
* Includes pressure gauge and fill valve
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Four Air-Solenoid Compressed Air Chamber
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –38
Compressed Air Chamber / Solenoid Support Items
Compressed Air Chamber/Air-Solenoid Trigger
MIL-EC-SSA
* Single Solenoid Head Assembly
* New style solenoids
Compressed Air Chamber / Solenoid Support Items
(Contact your sales representative if you are uncertain if your existing product uses the new style solenoids)
Description
Single Solenoid Head Assembly
MIL-EC-DSA
* Dual Solenoid Head Assembly
* New style solenoids
(Contact your sales representative if you are uncertain if your existing product uses the new style solenoids)
Description
Dual Solenoid Head Assembly
MIL-EC-FG
* Replacement part for the compressed air chamber
* Includes: End Cap, Gauge, Fill Valve and Fill Valve Cap
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Compressed Air Chamber End Cap
MIL-GAUGE-160PSI
* 160 PSI pressure custom gauge
* Color coded to identify minimum and maximum
operating pressures
* Polycarbonate window, stainless steel construction
Description
160 PSI Gauge
MIL-FVC2
* Replacement Fill Valve Cap with Tether
* Threadless Pliable Rubber Cap
Description
Fill Valve Cap with Tether
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –39
Compressed Air Chamber / Solenoid Support Items
Compressed Air Chamber/Air-Solenoid Trigger
MIL-SOL-BLUK
* Solenoid Kit with sure seal connectors, blue shrink wrap, O-Ring, screws loctite and silicone capsule
Description
Blue Lead Solenoid with Sure Seal Connector
Compressed Air Chamber / Solenoid Support Items
MIL-SOL-GRNK
* Solenoid Kit with sure seal connectors, green shrink wrap, O-Ring, screws loctite and silicone capsule
Description
Green Lead Solenoid with Sure Seal Connector
MIL-SOL-REDK
* Solenoid Kit with sure seal connectors, red shrink wrap, O-Ring, screws loctite and silicone capsule
Description
Red Lead Solenoid with Sure Seal Connector
MIL-SOL-YELK
* Solenoid Kit with sure seal connectors, yellow shrink wrap, O-Ring, screws loctite and silicone capsule
Description
Yellow Lead Solenoid with Sure Seal Connector
MIL-SV4-AT2
* Four Air-Solenoid Trigger with Sure Seal Connectors
* Wiring harness (sold separately) is available with 5 pin connector orbanana plugs
* Initiated by any 12 volt .5 amp output
* Uses low pressure (100 psi) CO2 or compressed air for initiation
* Includes pressure gauge and fill valve
* Machined aluminum
* MIL SPEC anodized matte finish
Description
Four Solenoid Compressed Air Chamber with Sure Seal Connectors
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –40
Compressed Air Chamber / Solenoid Support Items
Compressed Air Chamber/Air-Solenoid Trigger
MIL-ECH-WHB
Compressed Air Chamber / Solenoid Support Items
* Color coded wiring harness for the Four Solenoid Compressed Air Chamber
* Banana Plug Leads
* Sure Seal connectors
* Four solenoid connectors, two ECHO illum-fx connectors
Description
Sure Seal Connector Wiring Harness with Banana Plugs
MIL-ECH-WHSC
* Color coded wiring harness for the Four Solenoid Compressed Air Chamber
* Single (5 Pin ) Lead
* Sure Seal connectors
* Four solenoid connectors, Two ECHO Illum-Fx connectors
Description
Sure Seal Connector Wiring Harness with 5 Pin Connector
MIL-TSK
* Package of 10 Test/Tether Shunt
* Looped end fits under the airline connector to prevent loss of the shunt
* Plastic
Description
Tether Shunt
MIL-TST-K
* Package of 10 Tether Shunts
Description
Test Shunt
MIL-12G-QFT
* Used for filling Compressed Air Chambers
* Uses disposable 12 gram cartridges
* Brass and machined plastic
Description
Quick Fill Trigger
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –41
Compressed Air Chamber / Solenoid Support Items
Compressed Air Chamber/Air-Solenoid Trigger
MIL-12G-QFTK
* Converts existing MIL-12G-FVA to MIL-12G-QFT
Description
Quick Fill Trigger Upgrade Kit
Compressed Air Chamber / Solenoid Support Items
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –42
Distraction Device Support Items
Distraction Device Support Items
MIL-DD-012
* Package of 5 O-Rings used with MIL-DD-SIM Inner Piston
Inner Piston O-Ring Kit
MIL-DD-015
Distraction Device Support Items
* Package of 5 O-Rings used with MIL-DD-SIM Outer Piston
Description
Outer Piston O-Ring Kit
MIL-DD-129
* Package of 5 O-Rings used with MIL-DD-SIM CO2 Cartridge Housing
Description
CO2 Cartridge Housing O-Ring Kit
MIL-DD7-KIT
* Repair kit for the MIL-DD-SIM
* Includes 1 Outer Piston and 1 Inner Piston
Description
Distraction Device Repair Kit
MIL-DD-PIN
* Safety Pin replacement part for the MIL-DD-SIM
* Quick release pin with spring loaded ball
* Stainless steel
Description
Safety Pin
MIL-PPS-10
* Package of 10 Pierce Pin seals for DD-SIM
Description
Pierce Pin Seal
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –43
E3 Family Support Items
E3 Family
MIL-E3-RXPP
* Radio controlled 2 channel power supply
* 2 channel, 315 MHz - 500 foot LOS
* Timer, crush wire, pressure plate and tilt switch capabilities
* Aluminum with MIL SPEC anodized matte finish
Description
RX 2 Channel- Power Pack
MIL-E3-PP
E3 Family Support Items
* Power supply used for improvised detonation control with the buriable E3 system
* Timer, crush wire, pressure plate and tilt switch capabilities
* Aluminum with MIL SPEC anodized matte finish
Description
9 Volt Battery Power Pack
MIL-E3-BPH
* E3 powering device
* Electronically initiated
* Uses E3 head attachments
* Designed for extreme conditions (wet, dusty or buried)
* Aluminum with MIL SPEC anodized matte finish
Description
Buriable Power House
MIL-E3-PPBT
* E3 powering device
* Electronically, striker or hair pin initiated
* Uses E3 head attachments
* Aluminum with MIL SPEC anodized matte finish
Description
Universal Push/Pull Booby Trap
MIL-E3-DC
* Transfers initiating pressure from E3 Powering Device to detonate any MIL-SIM-FX product
* Aluminum with MIL SPEC anodized matte finish
Description
Detonator Cap
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –44
E3 Family Support Items
E3 Family
MIL-E3-ILH
* For use with E3 powering device
* Uses rubber burst disc and FX Powder (Cool Smoke)
* Directs effect straight out along a target line
* Aluminum with MIL SPEC anodized matte finish
Description
Inline Head Assembly
MIL-E3-RAH
E3 Family Support Items
* For use with E3 powering device
* Uses rubber burst disc and FX Powder (Cool Smoke)
* Directs effect at a 90° angle
* Aluminum with MIL SPEC anodized matte finish
Description
Right Angle Head Assembly
MIL-E3-RAHM
* Right Angle Head (with airline port) for use within the E3 family
Description
Right Angle Head with MILES Capability
MIL-E3-ETS
* External Trigger Switch with banana plugs
* Opens or closes an electrical current
Description
External Trigger Switch
MIL-E3-HBS
* Hacksaw Blade Switch Detonator
* Opens or closes an electrical current
Description
Hacksaw Blades
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –45
E3 Family Support Items
E3 Family
MIL-EIPB-MSW
* Ball Bearing Switch
* Tilt switch with wire harness and banana plugs
Description
Tilt Switch
MIL-E3-CBL
* 14 inch Connector Cable
Description
E3 Family Support Items
E3 Cable
MIL-SVX-CBL
* 38 inch Connector Cable
Description
38 inch Connector Cable
MIL-E3-RXC
* Magnetic Lid for the MIL-E3-RXPP
Description
Magnetic Lid
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –46
E4 Support Items
E4 Support Items
MIL-E4-SOLKIT
* One solenoid repair kit with 60 inch leads
* Bare wire leads specific to the E4
Description
E4 Solenoid Replacement Kit
MIL-E41-SOLKIT
* One solenoid repair kit with 60 inch leads
* Banana Plug leads specific to the E4-1
Description
E4-1 Solenoid Replacement Kit with Banana Plug Leads
E4 Support Items
MIL-E4-AT
* Compressed Air Chamber for the E4
* 60 inch bare wire leads
Description
E4 Air Trigger with Bare Wire Leads
MIL-E4-AT1
* Compressed Air Chamber for the E4-1
* With 60 inch banana plug leads
Description
E4 Air Trigger with Banana Plug Leads
MIL-E4-ATA
* Compressed Air Chamber / Base Assembly for the E4
* 60 inch bare wire leads
Description
E4 Air Trigger and Base Assembly with Bare Wire Leads
MIL-E4-ATA1
* Compressed Air Chamber / Base Assembly for the E4-1
* 60 inch banana plug leads
Description
E4 Air Trigger and Base Assembly with Banana Plug Leads
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –47
ECHO System Support Items
ECHO System Support Items
MIL-06ST-SMU
* 6" Volumizer with Male Union installs on existing ECHO System
* Doubles the FX Powder (Cool Smoke) (Cool Smoke) capacity/powder signature effect
* Holds 11 ounces of FX Powder (Cool Smoke) (Cool Smoke)
* MIL SPEC hard anodized matte finish
Description
6 inch Volumizer with Male Union
MIL-12-TP
ECHO System Support Items
* 12" Bottle Protector safeguards device when burying or placing a single ECHO device on a roadway
* MIL SPEC hard anodized matte finish
Description
Bottle Protector
MIL-ECH-BKIT
* Kit converts an individual device from the ECHO into a buriable device
* Includes: Airline, Dead Man Switch, Volumizer, Tank Protector and Right Angle Head
* MIL SPEC hard anodized matte finish
Description
Buriable Upgrade Kit
MIL-ECH-SP
* ECHO Set Plug replacement part
* Machined Aluminum
* MIL SPEC hard anodized matte finish
Description
Set Plug for Firing Initiator
MIL-ECH-TP
* ECHO Thread Protector replacement part
* Machined Aluminum
* MIL SPEC hard anodized matte finish
Description
Thread Protector
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –48
ECHO System Support Items
ECHO System Support Items
MIL-SS-FAS/W-2
* Stainless Steel fasteners used to attach the
MIL-ECH-CDH6 to the 5 cell caddy (NPSSD)
* Stainless/Rubber Washers
* Sold in Set of 2
Description
Replacement Bolts and Washers
MIL-THN-D
ECHO System Support Items
* Used to remove SS Fasteners from the 5 cell caddy
* Also used to remove airline connectors
* A steel ½" x 6" point socket T-Handle wrench
* Powder-coated blue
Description
T-handle Nut Driver
MIL-WOH6-ORK
* O-Ring replacement kit for the ECHO System
* Includes:
4 - 401 O-Rings
4 - 230 O-Rings
4 - Green Loctite capsules
Description
O-Ring Replacement Kit for the ECHO
MIL-ECH-FIS
* Dry Firing Set for New Equipment Training
* Can be used for indoor classroom environment or outdoor systems use
Description
Fire Indicator Set
MIL-4SOL-KIT
Replacement solenoid kit for the Compressed Air Chamber
* Long leads, no banana plugs
Description
4 Solenoid Repair Kit with Bare Wire Leads
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –49
Fill Station Support Items
Fill Station and Fill Station Support Items
MIL-FIL
* Includes:
1 - Fill Station
1 - Adaptor Hose/Adapter w/ Pin Depress Assembly
1 - Vent Hose Assembly
1 - Vent Hose Muffler
* Used for filling CO2 in the Refillable CO2 bottles
* Machined aluminum
Description
Fill Station Support Items
Fill Station
MIL-SCALE
* Used for weighing Refillable 9 oz CO2 tanks Molded plastic housing
* Digital electronics internal
Description
Weigh Scale
MIL-FIL-ADP
* Fill station adapter assembly replacement piece with pin depress
* Machined aluminum
* Stainless steel internal parts
* Plastic knob
Description
Fill Station Adapter
MIL-FIL-AHA
* Fill Station adapter assembly replacement piece with hose/pin depress
* Machined aluminum
* Stainless steel internal parts
* High pressure nylon hose
Description
Fill Station Adapter Hose Assembly
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –50
Fill Station Support Items
Fill Station and Fill Station Support Items
MIL-PD-ORK
* Package of 10 O-Ring
* Replacement O-Ring for the Fill Station Pin Depressor
* Urethane O-Ring
Description
Fill Station Pin Depressor O-Ring
MIL-FIL-BCW
Fill Station Support Items
* Package of 5 Bulk Tank Coupling Washers
* Design allows washer to seat snuggly in the threads and prevents washers from falling out and becoming lost
Description
Bulk Coupling Washer
MIL-FIL-KIT2
* Includes:
- Replacement O-Rings
- Valve Seats
- Pipe Nipple Disassembly Tool
- Silicone Grease Capsule
* Stainless, nylon, Buna internal parts
Description
Fill Station Service Kit
MIL-SL
* Silicone lube used to lubricate the O-Ring of the CO2 Filling Station
* Silicone lube
Description
Silicone Lube
MIL-FSW
* Fill Station Wrench
* Used to attach/remove valve to tank
* Steel powder coated
Description
Fill Station Wrench
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –51
Fill Station Support Items
Fill Station and Fill Station Support Items
MIL-12-AW
* 12" Adjustable Wrench
Description
Adjustable Wrench
MIL-516T-AW
* 5/16" T-Handle Wrench used to service the CO2 Fill Station
* Forged steel
Fill Station Support Items
Description
5/16 T-Handle Allen Wrench
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –52
Firing Actuators and Firing Actuator Assemblies
Firing Actuators and Firing Actuator Assemblies
MIL-12G-FA
* A standard 12 gram firing actuator
* Used in the small MIL-SIM-FX devices
* Machined aluminum
* MIL SPEC hard anodized matte finish
Firing Actuators and Firing Actuator Assemblies
Description
12 Gram Firing Actuator
MIL-12G-FBA
* 12 gram Tank Base/Firing Actuator Assembly Includes:
1 - 12 gram Tank Base
1 - 12 gram Tank Firing Actuator
1 - 5 Inch Slams Tube
1 - 12 gram Cartridge Housing
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
12 Gram Tank Base Firing Actuator Assembly
MIL-12G-NCA
* 12 gram Tank Base/Nose Cone Firing Actuator Assembly Includes:
1 - 12 gram Tank Base
1 - 12 gram Nose Cone Firing Actuator
1 - 5 Inch Slams Tube
1 - 12 gram Cartridge Housing
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
12 Gram Nose Cone Firing Actuator Assembly
MIL-9R-FA
* Standard 6oz firing actuator
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
9 Ounce Firing Actuator
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –53
Firing Actuators and Firing Actuator Assemblies
Firing Actuators and Firing Actuator Assemblies
MIL-12G-NFA
* 12 gram nose cone firing actuator
* Used in the small MIL-SIM-FX devices
* Machined aluminum
* MIL SPEC hard anodized matte finish
Firing Actuators and Firing Actuator Assemblies
Description
12 Gram Nose Cone Firing Actuator
MIL-9R-FBA
* 9 ounce Tank Base/Firing Actuator Assembly Includes:
1 - 9 ounce Tank Base
1 - 9 ounce Tank Firing Actuator
1 - Airline Connector
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
9 Ounce Tank Base/ 9 Ounce Firing Actuator Assembly
MIL-9R-NFA
* 9oz nose cone firing actuator
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
9 Ounce Nose Cone Firing Actuator
MIL-9R-NCA
* 9 Ounce Tank Base/Nose Cone Firing Actuator Assembly Includes:
1 - 9 Ounce Tank Base
1 - 9 Ounce Nose Cone Firing Actuator
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
9 Ounce Tank Base/ 9 Ounce Nose Cone Firing Actuator Assembly
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –54
Ground Stakes and Ground Stake Support Items
Ground Stakes and Ground Stake Support Items
MIL-4.5-GS
* 4.5" ground stake used with the ECHO System
* Heat treated anodized steel
Description
Ground Stakes and Ground Stake Support Items
4.5 inch Ground Stake
MIL-06-GS
* 6" ground stake used on the Directional Charge Head (MIL-180-CH) and the Ground Stake Block (MIL-90-GSB)
* Heat treated anodized steel
Description
6 inch Ground Stake
MIL-08-GS
* 8" ground stake used on the Ground Stake Block (MIL-90-GSB)
* Heat treated anodized steel
Description
8 inch Ground Stake
MIL-90-GSB
* Ground stake block used with ground stakes on a number of MIL-SIM-FX devices
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
90 Degree Ground Stake Black
MIL-GSB-6A
* Ground Stake Block / 6 Inch Ground Stake Assembly
* Machined aluminum / Heat treated anodized steel
Description
Ground Stake Assembly with 6 inch Stakes
MIL-GSB-8A
* Ground Stake Block / 8 Inch Ground Stake Assembly
* Machined aluminum / Heat treated anodized steel
Description
Ground Stake Assembly with 8 inch Stakes
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –55
Ground Stakes and Ground Stake Support Items
Ground Stakes and Ground Stake Support Items
MIL-GSB-BLT
* Replacement 3/8" bolt used in the ground stake block
* Stainless steel
Description
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Ground Stakes and Ground Stake Support Items
Ground Stake Block Replacement Bolt
Page –56
Hardwire Detonators Support Items
Hardwire via Airline Support Items
MIL-12G-TCDA
* Trigger Command Detonator Upgraded Airline Connector Kit
* Includes brass fitting, airline connector and roll pin
Description
Trigger Command Detonator Upgrade
Hardwire Detonators Support Items
MIL-18-1032-ACK
* Package of 1/8" x 10/32" airline connector for connecting the airline to the MIL-SIM-FX device
* Push lock connection
* Plated brass with nylon part
Description
Airline Connectors 1/8 X 10/32
MIL-DMS-PLG
* Replacement Part
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Dead Man's Switch Detonator Plug
MIL-PAD-PLG
* Replacement Part
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Pressure Applied Detonator Plug
MIL-DMS-SQB
* Replacement Part
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Low Profile SQUIB for the Dead Man's Switch Detonator
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –57
Hardwire Detonators Support Items
Hardwire via Airline Support Items
MIL-LIB
* Lever Initiated Body - Replacement Part
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Lever Initiated Body
MIL-FVA-ORK
Hardwire Detonators Support Items
* Small O-Ring fits inside the Fill Valve Adapter
* Package of 10 O-Rings
Description
Fill Valve Adapter O-Ring Kit
MIL-LP
* Used in the MIL-12G-PAD, MIL-12G-DMS, MIL-DMS-IED
* Plastic lanyard with two stainless steel pins
Description
Pressure/Sensitive Device Lanyard and 2 Safety Pins
MIL-MFD-KIT
* Striker, spring and screw used in the Multifunction Detonator
* Stainless Steel
Description
Multi-function Detonator Repair Kit
MIL-TCD-12C
* Cup used for holding the disposable 12 gram cartridges
* Connects to the Trigger Command Detonators head
* Molded plastic
Description
Trigger Command Detonator Cup
MIL-TCD-FVA
* A Conversion adapter that allows for the Trigger Command Detonator to be used as a compressed air filling device
* Stainless steel
Description
Trigger Command Detonator Adapter
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –58
Hardwire Detonators Support Items
Hardwire via Airline Support Items
MIL-TCD-ORK
* O-Ring used in the head of the Trigger Command Detonator
* Includes capsule of silicone grease
* 10 - Urethane O-Rings
Description
12 gram Trigger Command Detonator O-Ring
Hardwire Detonators Support Items
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –59
Heads
Heads
MIL-110-FHA
* Female Adapter used on the MIL-SIM-FX IED heads for a 110 degree ground marking effect
* Machined aluminum
* MiIL SPEC hard anodized matte finish
Description
LP Female Adapter with 110 Degree Spray Pattern
MIL-110-MFA
* Head assembly includes:
1 - Mortar Fin Attachment w/ 7 Fins
1 - Dispersed Impact Head
1 - LP Female Adapter w/ 110° Spray Pattern
1 - Stainless Steel Deflector
Heads
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Mortar Fin Head/ Female Adapter with 110 Spray Assembly
MIL-110-PEA
* Head assembly includes:
1 - Pointed End Cap
1 - LP Female Adapter w/ 110° Spray Pattern
1 - Stainless Steel Deflector
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Pointed End Cap/Female Adapter with 110 Spray Assembly
MIL-180-CH
* Directional charge head used on the MIL-SIM-FX IED tubes (recommend to be used with ground stakes attached)
* Has marking rounds capability for damage assessment
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Directional Charge/Improvised Claymore
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –60
Heads
Heads
MIL-180-CHA6
* Head assembly includes:
1 - Directional Charge Head
1 - LP Male Adapter
2 - 6 Inch Ground Stakes
* Has marking rounds capability for damage assessment
* Machined aluminum
* Mil spec hard anodized matte finish
Description
Directional Charge Head/Male Adapter with 6 inch Stakes
MIL-180-CHA8
Heads
* Head assembly includes:
1 - Directional Charge Head
1 - LP Male Adapter
2 - 8 Inch Ground Stakes
* Has marking rounds capability for damage assessment
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Directional Charge Head/Male Adapter with 8 inch Stakes
MIL-180-FHA
* Female Adapter used on the MIL-SIM-FX IED heads for a 180 degree ground marking effect
* Machined aluminum
* MiIL SPEC hard anodized matte finish
Description
LP Female Adapter with 180 Degree Spray Pattern
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –61
Heads
Heads
MIL-180-MFA
* Head assembly includes:
1 - Mortar Fin Attachment w/ 7 Fins
1 - Dispersed Impact Head
1 - LP Female Adapter w/ 180° Spray Pattern
1 - Stainless Steel Deflector
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Mortar Fin Head/ Female Adapter with 180 Spray Assembly
MIL-180-PEA
Heads
* Head assembly includes:
1 - Pointed End Cap
1 - LP Female Adapter w/ 180° Spray Pattern
1 - Stainless Steel Deflector
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Pointed End Cap/Female Adapter with 180 Spray Assembly
MIL-250-SMA
* Male Adapter used on the MIL-SIM-FX IED heads
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
LP Male Adapter
MIL-3-CDH
* This combination Head uses either rubber or plastic burst discs
* Machined Aluminum with MIL SPEC hard anodized matte finish
* Retainer ring (MIL-BD-RR) sold separately
Description
Combination Disc Head
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –62
Heads
Heads
MIL-4-BFA
* Bomb Fin Visual Modification
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Bomb Fin Attachment with 4 Fins
MIL-6-DPH
* Commonly used with the Bomb Fin attachment (MIL-4-BFA) and the Mortar Fin Attachment (MIL-7-MFA)
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Dispersed Impact Head
Heads
MIL-6-MFA
* A 6 fin mortar head visual modification used on the MIL-SIM-FX IED tubes
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Mortar Fin Assembly with 6 Fins
MIL-7-MFA
* A 7 fin mortar visual modification used with the MIL-6-DPH
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Mortar Fin Assembly with 7 Fins
MIL-90-CH
* Directional charge head used on the MIL-SIM-FX IED tubes
* Eyelets can be attached for fastening head to an object
* Has marking rounds capability for damage assessment
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
ARC Head
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –63
Heads
Heads
MIL-90-CHA
* Head assembly includes:
1 - A.R.C. Head
1 - LP Male Adapter
2 - Eyelet Screws
* Has marking rounds capability for damage assessment
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
ARC Head/Male Adapter Assembly - With Eyelets
MIL-E4-CHA
Heads
* Head assembly includes:
1 - A.R.C. Head
1 - LP Male Adapter
* Has marking rounds capability for damage assessment
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
ARC Head/Male Adapter Assembly - No Eyelets
MIL-EC-ST
* End cap used when transporting powder filled MIL-SIM-FX IED 120mm (MIL-120-SM) and 20 inch (MIL-20-ST) tubes
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
End Cap
MIL-EFP
* Explosively Formed Penetrator Simulator Head
* Specifically designed to be used with marking rounds
* 42" marking zone at approximately 25 feet
* MIL SPEC anodized matte finish
Description
Explosively Formed Penetrator Array Head
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –64
Heads
Heads
MIL-PEC-ST
* Pointed End cap used on the MIL-SIM-FX IED devices
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Pointed End Cap
MIL-PET-BA
* Used on the larger MIL-SIM-FX tubes for exploding plastic beverage bottles
* Allows for maximum audio signature
* Machined aluminum
* MIL SPEC hard anodized matte finish
Heads
Description
Concussive PET Bottle Adapter
MIL-PET-DBA
* Directional Charge Capabilities ( 60° Cone Spray)
* Used on the larger MIL-SIM-FX tubes and ECHO System for exploding plastic beverage bottles
* Allows for maximum audio signature
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Directional Charge Concussive PET Bottle Adapter
MIL-SMA-TP
* Thread protector replacement part
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Thread Protector for LP Male Adapter
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –65
Landmine Support Items
Landmine Support Items
MIL-14-40-OFF
* Pressure Sensitive CO2 Pierce Pin for Pressure Sensitive Landmine
* 40 lbs step off detonation
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Pressure Release Pin for MIL-LM
MIL-14-40-ON
Landmine Support Items
* Pressure sensitive CO2 pierce pin for Pressure Sensitive Landmine
* 40 lbs step on detonation
* Machined Aluminum
* MIL SPEC hard anodized matte finish
Description
Pressure Applied Pin for MIL-LM
MIL-16-SPK
* Package of 2
* 7/8 X 2 Landmine Spring
Description
Landmine Spring
MIL-M16LM6
* Landmine base plug
* MIL SPEC hard anodized aluminum
Description
Landmine Base Plug
MIL-LM-PRT
* Removes Landmine base plug
* Stainless steel with lanyard
Description
Landmine Base Plug Removal Tool
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –66
Miscellaneous Support Items
Miscellaneous Service Parts
MIL-BD-RR
* Rubber burst disc retainer ring used with various devices
* Machined aluminum
* MIL SPEC hard anodized matte Olive Drab finish
Description
Burst Disc Retainer Ring
MIL-PET-N
Miscellaneous Support Items
* Replacement nut
* Works in conjunction with the Concussive FX PET Bottle Adapter Head and the Directional Charge PET Bottle Adapter Head
Description
PET Bottle Adapter- Replacement Nut
MIL-12G-SB1
* 12 gram Cartridge Housing used in the 5 inch tube assembly
* MIL SPEC hard anodized matte finish
* Machined aluminum
Description
12 gram CO2 Cartridge Housing
MIL-PP
* Safety/Pull pin used in MIL-E3-PPBT
* Sold in singles
Description
Safety/Pull Pin
MIL-SFTY-K
* Package of 10
* Safety pin for many of the MIL-SIM-FX IED's
* 4571 Stainless Steel
Description
Anti-Personnel Safety Pin
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –67
Miscellaneous Support Items
Miscellaneous Service Parts
MIL-HTP
* A tapered pin for use in specific Tripwire devices
* 4571 stainless steel
* Sold in singles
Description
Hair Trigger Pin
MIL-6F-TW
Miscellaneous Support Items
* Tripwire and Hair Trigger Pin
* 4571 stainless steel
Description
Tripwire - 6 Foot Length
MIL-CHA-ENS
* Package of ten Eyelets with nuts for the CHA head
Description
Eyelet and Nut Set
MIL-LNYRD
* Lanyard
* Polypropylene web
Description
Lanyard
MIL-SPN
* Measuring spoon for measuring FX Powder (Cool Smoke)
* Stainless Steel
Description
Measuring Spoon
MIL-6-001
* Steel deflector used in the MIL-SIM-FX ordnance and mortar fin vismods
* Stainless steel
Description
Stainless Steel Deflector
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –68
Miscellaneous Support Items
Miscellaneous Service Parts
MIL-12V-7AH
* Rechargeable Battery
* 7 AMP Hours
* Bolt Posts
Description
Rechargeable Battery
Miscellaneous Support Items
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –69
O-Rings
O-Ring
MIL-TCD-ORK
* Package of 10
* Trigger Command O-Ring Replacement
Description
Trigger Command Detonator O-Rings
MIL-PD-ORK
* Package of 10
* Pin Depressor O-Ring Replacement
Description
Pin Depressor O-Ring
MIL-41010-ORK
O-Rings
* Package of 10
* Urethane O-Rings used on the High Pressure Bottle, ECHO Set Plug and ECHO Firing Indicator
Description
CO2 Bottle O-Ring
MIL-013-ORK
* Package of 10
* 013 O-Ring
Description
Solenoid Replacement O-Ring Buna
MIL-020-ORK
* Package of 10
* 020 O-Ring
Description
Urethane O-Ring Kit
MIL-022-ORK
* Package of 10
* 022 HNBR 70 Durometer O-Rings
Description
O-Ring Kit for the 12 gram Cartridge Housing
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –70
O-Rings
O-Ring
MIL-116H-ORK
* Package of 10
* 116 HNBR 70 Durometer O-Rings
Description
HNBR O-Ring Kit for the Firing Actuator and Landmine Base Plug
MIL-126-ORK
* Package of 10
* 126 HNBR 70 Durometer O-Rings
Description
HNBR O-Ring Kit
MIL-130-ORK
O-Rings
* Package of 10
* 130 HNBR 70 Durometer O-Rings
Description
HNBR O-Ring Kit for the PET Bottle Adapter
MIL-228-ORK
* Package of 10
* 228 HNBR 70 Durometer O-Rings
Description
HNBR O-Ring Kit
MIL-230-ORK
* Package of 10
* 230 Urethane 70 Durometer O-Rings
* Used Specifically on the MIL-3-CDH
Description
Urethane O-Ring Kit
MIL-230H-ORK
* Package of 10
* 230 HNBR 70 Durometer O-Rings
Description
HNBR O-Ring Kit
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –71
O-Rings
O-Ring
MIL-401-ORK
* Package of 10
* 401 HNBR 70 Durometer O-Rings
Description
HNBR O-Ring Kit
O-Rings
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –72
Radio Controlled Support Items
Antenna
MIL-ANT-1A
* Antenna used on the Long Range Electronic Firing Device as well as the Long Range Transmitters
* Rubber antenna with steel fitting
* Includes Antenna Adapter (MIL-ANT-ADP)
Description
8 inch Rubber Whip Receiver Antenna
MIL-ANT-1B
Radio Controlled Support Items
* Antenna used on the Long Range Electronic Firing Device as well as the Long Range Transmitters
* Rubber antenna with steel fitting
* Antenna Adapter (MIL-ANT-ADP) NOT Included
Description
8 inch Rubber Whip Antenna - No Adapter
MIL-ANT-ADP
*Antenna adapter used on the Long Range Electronic Firing Device/Long Range Transmitters
Description
Antenna Adapter
Transmitters
MIL-TX-1CH
* Single button short range remote with lanyard
* Used with any short range radio controlled device
* Formed plastic
* 315 MHz - 500 Feet LOS
Description
One Channel/Button Transmitter (315 MHz)
MIL-TX-2CH
* A two button short range remote with lanyard
* Used with any short range radio controlled device
* 315 MHz - 500 Feet LOS
* Formed plastic
Description
Two Channel/Button Transmitter (315 MHz)
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –73
Radio Controlled Support Items
Transmitters
MIL-TXL-1CH
* A single button long range radio transmitter
* Used with any long range radio controlled device
* 27 MHz - 1 Mile LOS
* Cast plastic
Description
One Channel/Button Transmitter (27 MHz)
Radio Controlled Support Items
MIL-TXL-4CH
* A four button long range radio transmitter
* Used with any long range radio controlled device
* 27 MHz - 1 Mile LOS
* Cast plastic
Description
Two Channel/Button Transmitter (27 MHz)
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –74
Suicide Vest Support Items
Suicide Vests Support Items
MIL-SVX
* Modular Velcro pouches distribute weight evenly and allow for a variety of configurations on both front and back of vest
* One size fits all
* Pouches are sold separately
* Power pack pouch (for remote detonation) is also available
Description
Suicide X-Vest
MIL-SVX-PBP
Suicide Vest Support Items
* One Single Pipe Bomb Pouch used with the Suicide X-Vest
* H.D. Canvas
Description
SVX Power Pack Pouch
MIL-SVX-RBP
* One Single Power Pack Pouch used with the Suicide X-Vest
* H.D. Canvas
Description
SVX Pipe Bomb Pouch
MIL-SVX-CBL
* 38 inch Connector Cable
Description
38 inch Connector Cable
MIL-SVX-RC
* MIL-SVX4R Ripcord Replacement
* 14 inches length
Description
SV4R Ripcord Replacement
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –75
Tubes
Tubes
MIL-05-ST
* Small IED Tube
* Holds up to 4 oz of FX Powder (Cool Smoke)
* Base (MIL-12G-SB) not included
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
5 Inch Tube
MIL-06ST-A
* ECHO Tube
* Holds up to 11 oz of FX Powder (Cool Smoke)
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
Tubes
6 inch Tube
MIL-20-ST
* Medium IED Tube
* Holds up to 22 oz of FX Powder (Cool Smoke)
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
20 inch Tube
MIL-120-SIM
* Large IED Tube
* Holds up to 44 oz of FX Powder (Cool Smoke)
* Machined aluminum
* MIL SPEC hard anodized matte finish
Description
120mm SIM Tube
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected]
Page –76